SUSPENSION

WT
A

B
SECTION
ROAD WHEELS & TIRES C

WT
CONTENTS
PRECAUTION ............................................... 2 WHEEL AND TIRE ............................................. 5 F
Adjustment ................................................................ 5
PRECAUTIONS ................................................... 2
Precaution for Supplemental Restraint System REMOVAL AND INSTALLATION ................ 8 G
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ................................................................... 2 WHEEL AND TIRE ............................................. 8
Service Notice and Precautions for Road Wheel ...... 2 Exploded View .......................................................... 8
Removal and Installation .......................................... 8 H
PREPARATION ............................................ 3
SERVICE DATA AND SPECIFICATIONS
PREPARATION ................................................... 3 (SDS) ............................................................. 9 I
Commercial Service Tool .......................................... 3
SERVICE DATA AND SPECIFICATIONS
PERIODIC MAINTENANCE .......................... 4 (SDS) .................................................................. 9
Wheel ....................................................................... 9 J
WHEEL ................................................................ 4 Tire Air Pressure ....................................................... 9
Inspection .................................................................. 4
K

Revision: April 2013 WT-1 2014 Note

 PRECAUTIONS
< PRECAUTION >
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER" INFOID:0000000009445894

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Service Notice and Precautions for Road Wheel INFOID:0000000009443478

• Genuine NISSAN aluminum wheel is designed for each type of vehicle. Use it on the specified vehicle only.
• Use Genuine NISSAN parts for the road wheels, valve caps and wheel nuts.
• Always use them after adjusting the wheel balance. For the balance weights, use Genuine NISSAN alumi-
num wheel weights.
• Use caution when handling the aluminum wheels, because they can be easily scratched. When removing
dirt, do not use any abrasives, a wire brush, or other items that may scratch the coating. Use a neutral deter-
gent if a detergent is needed.
• After driving on roads scattered with anti-icing salts, wash off the wheels completely.
• When installing road wheels onto the vehicle, always wipe off any dirt or foreign substances to prevent them
from being trapped between the contact surfaces of wheel.
• Do not apply oil to nut and bolt threads.
• When tightening the valve cap there is a risk of damaging the valve cap if a tool is used. Tighten by hand.

Revision: April 2013 WT-2 2014 Note

 PREPARATION
< PREPARATION >
PREPARATION A
PREPARATION
Commercial Service Tool INFOID:0000000009443480
B

Tool name Description

C
Power tool Loosening nuts, screws and bolts

WT
PIIB1407E

Revision: April 2013 WT-3 2014 Note

 WHEEL
< PERIODIC MAINTENANCE >
PERIODIC MAINTENANCE
WHEEL
Inspection INFOID:0000000009641735

1. Check tires for wear and improper inflation.

2. Check wheels for deformation, cracks and other damage. If deformed, remove wheel and check wheel
runout.
a. Remove tire from wheel and mount wheel on a balancer machine.
b. Set dial indicator as shown.
c. Check runout, if runout value exceeds the limit, replace wheel.

Limit
Axial Runout (A) Refer to WT-9, "Wheel".
Radial Runout (B) Refer to WT-9, "Wheel".

SEIA0737E

Revision: April 2013 WT-4 2014 Note

 WHEEL AND TIRE
< PERIODIC MAINTENANCE >
WHEEL AND TIRE
A
Adjustment INFOID:0000000009641736

BALANCING WHEELS (ADHESIVE WEIGHT TYPE) B

Preparation Before Adjustment
Remove inner and outer balance weights from the wheel and tire. Using releasing agent, remove double-faced
adhesive tape from the wheel and tire. C
CAUTION:
• Be careful not to scratch the wheel and tire during removal.
• After removing double-faced adhesive tape, wipe clean all traces of releasing agent from the wheel D
and tire.
Wheel Balance Adjustment
CAUTION: WT
• DO NOT use center hole cone-type clamping machines to hold the wheel during tire removal/installa-
tion or balancing or damage to the wheel paint, cladding or chrome may result. Use only rim-type or
universal lug-type clamping machines to hold the wheel during servicing.
• If a balancer machine has an adhesive weight mode setting, select the adhesive weight mode setting and F
skip Step 2 below. If a balancer machine only has the clip-on (rim flange) weight mode setting, follow Step 2
to calculate the correct size adhesive weight.
1. Set wheel and tire on balancer machine using the center hole as a guide. Start the balancer machine. G
2. For balancer machines that only have a clip-on (rim flange) weight mode setting, follow this step to calcu-
late the correct size adhesive weight to use. When inner and outer imbalance values are shown on the
balancer machine indicator, multiply outer imbalance value by 5/3 (1.67) to determine balance weight that H
should be used. Select the outer balance weight with a value closest to the calculated value above and
install in to the designated outer position of or at the designated angle in relation to the wheel and tire.
a. Indicated imbalance value × 5/3 (1.67) = balance weight to be I
installed
Calculation example:
23 g (0.81 oz) × 5/3 (1.67) = 38.33 g (1.35 oz) ⇒ 40 g (1.41 oz)
J
balance weight (closer to calculated balance weight value)
NOTE:
Note that balance weight value must be closer to the calculated
balance weight value. K
Example:
37.4 ⇒ 35 g (1.23 oz)
37.5 ⇒ 40 g (1.41 oz) L
SMA054D

Revision: April 2013 WT-5 2014 Note

 WHEEL AND TIRE
< PERIODIC MAINTENANCE >
3. Install balance weight in the position shown.
CAUTION:
• Do not install the inner balance weight before installing
the outer balance weight.
• Before installing the balance weight, be sure to clean the
mating surface of the wheel and tire.
• When installing balance weight (1) to wheel and tire, set it into
the grooved area (A) on the inner wall of the wheel and tire as
shown so that the balance weight center (B) is aligned with the
balancer machine indication position (angle) (C).
CAUTION:
• Always use Genuine NISSAN adhesive balance weights.
• Balance weights are non-reusable; always replace with
new ones.
• Do not install more than three sheets of balance
weights.

JPEIC0040ZZ

4. If calculated balance weight value exceeds 50 g (1.76 oz), install

two balance weight sheets in line with each other as shown.
CAUTION:
Do not install one balance weight sheet on top of another.
5. Start balancer machine again.
6. Install balance weight on inner side of wheel and tire in the bal-
ancer machine indication position (angle).
CAUTION:
Do not install more than two balance weights.
7. Start balancer machine. Make sure that inner and outer residual
imbalance values are 5 g (0.17 oz) each or below. PEIA0033E

8. If either residual imbalance value exceeds 5 g (0.17 oz), repeat installation procedures.

Wheel balance Dynamic (At flange) Static (At flange)

Maximum allowable im-
Refer to WT-9, "Wheel".
balance

TIRE ROTATION
• Follow the maintenance schedule for tire rotation service intervals.
Refer to MA-7, "FOR MEXICO : Periodic Maintenance" (FOR
MEXICO), or MA-9, "EXCEPT FOR MEXICO : Periodic Mainte-
nance" (EXCEPT FOR MEXICO).
• Rotate the wheel and tires front to back in the pattern as shown.
• When installing the wheel, tighten wheel nuts to the specified
torque.
WARNING:
• After rotating the tires, check and adjust the tire pressure.
• Retighten the wheel nuts when the vehicle has been driven
for 1,000 km (600 mi) (also in case of a flat tire, etc.). SMA829C
• Do not include the spare tire when rotating the tires.

CAUTION:
• When installing wheels, tighten them diagonally by dividing the work two to three times in order to
prevent the wheels from developing any distortion.

Revision: April 2013 WT-6 2014 Note

 WHEEL AND TIRE
< PERIODIC MAINTENANCE >
• Be careful not to tighten the wheel nuts to a torque exceeding specification to prevent strain on the
disc rotor. A
• Use Genuine NISSAN wheel nuts.

Wheel nut tightening : WT-8, "Exploded View" B

torque

WT

Revision: April 2013 WT-7 2014 Note

 WHEEL AND TIRE
< REMOVAL AND INSTALLATION >
REMOVAL AND INSTALLATION
WHEEL AND TIRE
Exploded View INFOID:0000000009446829

JSGIA0969GB

1. Wheel and tire

Removal and Installation INFOID:0000000009446830

REMOVAL
1. Remove wheel nuts using power tool.
2. Remove wheel and tire.
INSTALLATION
Installation is in the reverse order of removal.

Revision: April 2013 WT-8 2014 Note

 SERVICE DATA AND SPECIFICATIONS (SDS)
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS) A
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel INFOID:0000000009443523
B

ALUMINUM WHEEL
C
Item Limit
Axial runout
Runout Less than 0.3 mm (0.012 in)
Radial runout D
Dynamic (At flange) Less than 5 g (0.17 oz) (one side)
Allowable imbalance
Static (At flange) Less than 10 g (0.35 oz)
WT
Tire Air Pressure INFOID:0000000009443524

Unit: kPa (kg/cm2, psi) F

Cold tire pressure
Tire size
Front Rear Spare
P195/55R16 86H
G
230 (2.3, 33) 230 (2.3, 33) —
P185/65R15 88H
T125/70D15 — — 420 (4.2, 60) H

Revision: April 2013 WT-9 2014 Note