The PCI bus

Main features
•  coupling of the processor and expansion bus by means of a bridge,
•  32-bit standard bus width with a maximum transfer rate of 133
Mbytes/s,
•  expansion to 64 bits with a maximum transfer rate of 266 Mbytes/s,
–  PCI-64/66 532 Mbytes/s,PCI-X 64/133 1064 Mbytes/s
•  supporting of multi-processor systems,
•  burst transfers with arbitrary length,
•  supporting of 5 V and 3.3 V power supplies,
•  write posting and read prefetching,
•  multimaster capabilities,
•  operating frequencies from 0 MHz to a maximum of 33 MHz,
–  PCI-66 3.3V only, PCI-X 100MHz-133MHz
•  multiplexing of address and data bus reducing the number of pins,
•  supporting of ISA/EISA/MCA,
•  configuration through software and registers,
•  processor independent specification
Block diagram of a PCI bus system
Processor/Main Memory System
Copro- Main
CPU Cache
cessor Memory

PCI Motion
Audio
Bridge Video
PCI Bus

SCSI host Interface to LAN Graphics

I/O
adapter Expansion Bus adapter adapter
Expansin Bus (ISA/EISA)

Bus Slot Bus Slot Bus Slot Bus Slot

PCI Chipset on Motherboard
PCI bus
PCI bus Signals
•  ACK64 # : acknowledge 64-bit transfer
•  AD31-AD0: 32 address and data pins form the multiplexed PCI address and data bus
•  C/BE3#-C/BE0#: command and byte-enable
•  CLK: PCI clock signal
•  DEVSEL#: device select
•  FRAME:
•  GNT#: grant
•  IDSEL: device select during configuration
•  INTA#, INTB#, INTC#, INTD#: interrurpt signals
•  IRDY#: initiator ready
•  LOCK: defines an atomic access
•  PAR: even parity for AD31-AD0 and C/BE3#-C/BE0#
•  PERR#: parity error
•  PRSNT1#, PRSNT2#: indicate that an adapter is installed
•  REQ#: request signal to the bus arbitration unit
•  REQ64#: 64-bit transfer request
•  RST: resets all PCI units
•  SBO#: snoop backoff, indicates a hit to a modified cache line
•  SDONE: snoop done
•  SERR#: system error
•  STOP: target-abort
•  TCK, TDI, TDO, TMS, TRST#: JTAG boundary scan test signals
•  TRDY: target ready
•  64 bit expansion
–  AD63-AD32: 32 address and data pins form the expansion of the multiplexed PCI address and
data bus
–  C/BE7#-C/BE4#
–  PAR64: even parity for the 64bit expansion
The PCI read transfer burst
The PCI write transfer burst.
PCI bus features

•  Bus Arbitration
–  Parallel arbitration
–  Hidden arbitration
–  Arbitration algorithm is not defined
•  DMA
–  Burst transfers
•  Interrupts
–  INTA# activated
–  Data: interrupt vector
 PCI Bus Cycles
•  INTA sequence (0000)
•  special cycle (0001)
•  I/O read access (0010)
•  I/O write access (0011)
•  memory read access (0110)
•  memory write access (0111)
•  configuration read access (1010)
•  configuration write access (1011)
•  memory multiple read access (1100)
•  dual addressing cycle (1101)
•  line memory read access (1110)
•  memory write access with invalidation (1111)
 PCI Configuration Address Space

31 16 15 0
•  Manufacturer ID
64 Byte Header
Unit ID
Status
Manufacturer ID
Command
–  allocated by PCI SIG
BIST
Class code
Header Latency
Revision
CLS •  Unit ID, revision
–  identifies unit
192 Bytes Available

•  Class code
for PCI Unit
Base Address register

–  type of PCI unit

Reserved
Reserved
Expansion ROM Base Address
Reserved
Reserved
Max. Lat. Min. GNT INT-Pin INT-Line
 Status and Command Registers

•  Status: •  Command:
–  PER: Parity error –  BEE: Fast back-to-back cycles
–  SER: System error (Back-to-Back Enable)
–  MAB: Master abort –  SEE: SERR Enable
–  TAB: Target abort received –  WC: Wait cycle control
–  STA: Target abort signaled –  PER: Parity error (Parity Error
–  DEVTIM: DEVSEL timing Response)
•  00=fast 01=medium –  VPS: VGA palette snoop
10=slow 11=reserved –  MWI: Memory write access with
–  DP: Data parity error invalidation
–  FBB: Fast back-to-back –  SC: Special cycle
cycles supported/ –  BM: Busmaster
unsupported –  MAR: Activate/deactivate
Memory address area
–  IOR: Activate/deactivate I/O
address area
 PCI Configuration Address Spaces

•  Configuration Mechanism #1
–  CONFIG-ADDRESS (0cf8h) and CONFIG-
DATA (0cfch) registers are defined in the I/O
area
31 30 24 23 16 15 11 10 8 7 2 1 0
ECD

Reserved Bus Unit Function Register Type

•  Configuration Mechanism #2 (for PC

systems)
–  4k I/O address range between c000h and cfffh
 PCI Base Address Registers
For Memory Address Space
31 16 15 4 3 2 1 0

PRF
Base Address Type 0

For I/O Address Space

31 16 15 2 1 0

PRF
Base Address 0

For Expansion ROM Address Space

31 16 15 11 10 2 1 0

AD
Base Address Reserved 0

•  PRF: Prefetching not possible/prefetching possible

•  Type: Positioning type
–  00=any 32-bit address, 01=less than 1M, 10=any 64-bit address,
11=reserved
•  AD: Address decoding and expansion ROM deactivated/
activated
Evolution of PC buses
 The PCI Express Bus
•  Point to point protocol
–  x1, x2, x4, x8, x12, x16 or x32 point-to-point
Link

•  Differential Signaling
 Electrical Physical Layer Showing
Differential Transmitter and Receiver
PCI Express System
 PCI Express Properties
•  Packet Based Protocol
•  Bandwidth and Clocking
–  2.5 Gbits/sec/lane/direction
–  8b/10b encoding
–  250 Mbytes/sec/lane/direction
•  Address Spaces
–  Memory
–  I/O
–  Configuration (extended from 256 Bytes to 4
Kbytes)
 PCI Express Transactions
•  Transactions
–  memory read / write
–  I/O read / write
–  configuration read / write
–  new transaction type: Message transactions
•  Transaction Model
–  posted (split transaction communication)
–  non-posted
PCI Express Properties
•  Quality of Service (QoS)
–  deterministic latencies and bandwidth
•  Traffic Classes (TCs)
–  TCs can move through the fabric with different priority
•  Virtual Channels (VCs)
–  Each Traffic Class is individually mapped to a Virtual Channel
•  Interrupt Handling
–  Virtual wires
•  Power Management
–  device power states: D0, D1, D2, D3-Hot and D3-Cold
•  D0 is the full-on power state
•  D3-Cold is the lowest power state.
–  Link power states: L0, L0s, L1, L2 and L3
•  Hot Plug Support
•  PCI Compatible Software Model
PCI Express Topology
PCI Express Device Layers
PCI Express Transaction Layer Packets
 PCI-X-AS (advanced switching) Packet format

The PCI Express AS protocol is inserted into a base PCI Express format. The data
payload, in this case a PCI Express base packet, could be data in any protocol format as PCI
Express AS is protocol agnostic. The PCI Express AS protocol requires a start indicator, or
comma, and an AS header that contains the PI or Protocol Interface and the routing path of the AS packet.