Scribd
Upload
1K views3 pages

KWP2000 PLUS Manual PDF

The document provides instructions for using the KWP2000 PLUS ECU Flasher device to read and write ECU data. It explains how to install the driver, connect the device to the computer and vehicle, select the ECU type, and read or write data. The read process saves the original ECU data, while writing overrides the data with a new file. It stresses ensuring the correct ECU is selected before writing to avoid errors.

Uploaded by

Mário Pr
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
1K views3 pages

KWP2000 PLUS Manual PDF

The document provides instructions for using the KWP2000 PLUS ECU Flasher device to read and write ECU data. It explains how to install the driver, connect the device to the computer and vehicle, select the ECU type, and read or write data. The read process saves the original ECU data, while writing overrides the data with a new file. It stresses ensuring the correct ECU is selected before writing to avoid errors.

Uploaded by

Mário Pr
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

OBD2Repair

Web: www.obd2repair.com Email:[email protected]

KWP2000 PLUS Manual

OPERATION INSTRUCTIONS:

Install driver:

- Install the driver package to your notebook/pc.


- Connect the KWP2000 PLUS Flasher to a free USB port.
- At the window, point to the folder where you installed the driver package. -
Reboot.

How to READ data from a supported ECU:

- Connect the KWP2000 PLUS ECU Flasher to computer USB port and to the
diagnostic port of the car - Start the communication software in the computer.
- Turn ignition key to “ON” position. (Do not crank or start the engine). - Select
the ECU type you want to read/write from the given list.
- Select additional options (if needed)
- Click the READ button to read out the original data (where supported). - Save
the file to the Hard Disk, Edit or Forward it another folder

How to WRITE data to a supported ECU:

- Connect the KWP2000 PLUS ECU Flasher to computer USB port and to the
diagnostic port of the car - Start the communication software in the computer.
- Turn ignition key to “ON” position. (Do not crank or start the engine). - Select
the ECU type you want to read/write from the given list.
- Select additional options (if needed).
- Click the WRITE button and select the file you want to write - Follow the
instructions on screen
- Switch the ignition key to “OFF” position and wait for 10 seconds before
starting the engine again.

Reading the ECU EEPROM chip

First choose the vehicle and type of the engine's ecu you want to read/write
from the given list. If you have any doubt about the type of ECU, you can verify
it from the program.

When the dialogue window appears just click on INFO tab and wait for the
program to communicate with the
OBD2Repair
Web: www.obd2repair.com Email:[email protected]
ECU.

A moment later, the information about the ECU type will be shown. Just click
on “READ” tab to assure that you will have a copy of the original file (in case
there is some problem later).

When the program starts reading the ECU’s chip, DO NOT INTERRUPT the
process at this moment.

Choose where you want to save the original file and name it. To simplify your
work, name it same as the numbers that appear in the window display on
“Information of the ECU”.

Now the program will prompt you to turn the ignition key to “OFF” position. Do
as instructed and then click the “OK” button.

Writing into the ECU EEPROM chip

Choose the vehicle and type of the ECU (as in the “READ” process) click on
INFO tab. OPEN the file prepared for your vehicle or ECU type.

From the display, on the right window you will see the reference of the ECU
that corresponds to the open file. To confirm that this information matches with
our ECU type. Verify the numbers in both windows are the same just to be on
the save side.

If you are absolutely sure that everything you did is correct. Click on PROG tab,
the system will now erase the ECU flash memory and program it with the new
file. Please DO NOT INTERRUPT during this process.

When it had finished writing, just turn the ignition key to “OFF” position and
then confirm by clicking the OK button.

Wait for 10 seconds and it is done! Now you can enjoy the new ECU program.

NOTE:

For some cases, VAG cars (AUDI, VOLKSWAGEN, SEAT AND SKODA)
before attempting to flash the ECU
OBD2Repair
Web: www.obd2repair.com Email:[email protected]
chip, the instruments panel must be de-activated. Open the fuse box cover;
remove the 5A fuses as
indicated in red (refer figure below). With the instruments panel power cut off
you can try to access the ECU.

You might also like