SCANTLING CALCULATION

I. SCANTLING PARTICULARS
Length Overall (LOA) = 63 M
Length Between Perpendicular (L) = 61 M
Breadth (B) = 13 M
Draft (d) = 2.5 M
Depth(D) = 3.6 M

II. SCANTLING LENGTH (L)

L = LOA
63 x 97
100
L = 61.11 M

BREADTH (B)
B = 13 M

SCANTLING DEPTH (D)

D = 3.6 M

DRAFT (d)
d = 2.5 M

SECTION 3: SHELL PLATING

FRAME SPACING
REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 7,P.85

1
s = 720 ( L / 100 )¼ mm
s = 720 ( 61 / 100 )¼ mm
s = ### mm

2
s = 2 L + 480 mm
s = 2 61 + 480 mm
s = 602 mm

Adopt 558.8 millimeters for designed used

BOTTOM SHELL AND BILGE STRAKE

REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 3,P.55

b = 900 + 3.5 L mm
b = 900 + 3.5 61 mm
 SCANTLING CALCULATION

b = 1113.5 mm

Adopt 1219.2 mm for designed used

The thickness of the keel is not less than to be

THICKNESS OF THE KEEL PLATE

REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 3,P.55

t = 0.1 L + 5 mm
t = 0.1 61 + 5 mm
t = 11.1 mm

11.1 mm or 7/16 inch for design used that must higher

TRANSVERSE BOTTOM FRAMING

REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 3,P.55 √

t = 0.0063 s d + 2
t = 0.0063 600 2.121
t = 8.0186 mm
7.9375 mm or 5/16 inch for design used that must higher
(ROUND OFF)

LONGITUDINAL BOTTOM FRAMING

REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 3,P.55

1 s ( L + 170 ) mm
t = 4450
t = 558.8 61 + 170 mm
t = 4450
t = 5.8724 mm

2
t = 0.1 (L + 2) mm
t = 0.1 61 + 2 mm
t = 6.3 mm
Adopt 6.35 mm or 1/4 inch for design used
 SCANTLING CALCULATION

THICKNESS OF BOTTOM SHELL PLATING (INCLUDING SIDE SHELL PLATING)

√(𝑆/600)
FOR 0
REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 3,P.55

t = ( 0.05 L + 5) mm

t = 0.05 61 + 5
mm
t = 8.05 mm

7.9375 mm or 5/16 inch for design used (standard)

(ROUND OFF)

SIDE SHELL AND SHEERSTRAKE

THICKNESS OF SIDE SHELL PLATING WITHIN 0.4L AMIDSHIPS

REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 3,P.56

t = 0.0833 L + 3.5 mm
t = 0.0833 61 + 3.5 mm
t = 5.373 mm
6.35 mm or 1/4 inch for design used (standard)

THICKNESS OF SIDE SHELL PLATING

REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 3,P.56

t = 0.05 L + 5 mm
t = 0.05 61 + 5 mm
t = 8.05 mm
7.9375 mm or 5/16 inch for design used (standard)
(ROUND OFF)

WIDTH OF SHEERSTRAKE
REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 3,P.57

b = 870 + 4.5 L mm
b = 870 + 4.5 61 mm
b = 1144.5 mm
Adopt 1200 mm for designed used

SECTION 4: DECKS

THICKNESS OF STRENGTH DECK PLATING

 SCANTLING CALCULATION

REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS

CHAPTER E,SECTION 4,P.62

t = 0.05 L + 5 mm
t = 0.05 61 + 5 mm
t = 8.05 mm
7.9375 mm or 5/16 inch for design used (standard)
(ROUND OFF)

STRINGER PLATES

BREADTH OF STRINGER PLATES

REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 4,P.62

b = 6.8 L + 500 mm
b = 6.8 61 + 500 mm
b = 914.8 mm
Adopt 1219.2 mm for designed used

THICKNESS OF STRINGER PLATES

REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 4,P.62

t = t ( thickness of strength deck plating) x 1.35

mm
t = 8.05 x 1.35 mm
t = 10.868 mm

11.11 mm or 7/16 inch for design used (standard)

THICKNESS OF LOWER DECK PLATING

THICKNESS OF SECOND DECK PLATING OUTSIDE LINE
REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 4,P.65

t = 0.025 L + 5.5 mm
t = 0.025 61 + 5.5 mm
t = 7.025 mm
7.9375 mm or 5/16 inch for design used (standard)

THICKNESS OF SECOND DECK PLATING INSIDE LINE

REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 4,P.65
 SCANTLING CALCULATION

t = 0.02 L + 5 mm
t = 0.02 61 + 5 mm
t = 6.22 mm

6.35 mm or 1/4 inch for design used (standard)

THICKNESS OF THIRD DECK PLATING OUTSIDE LINE

REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 4,P.65

t = 0.022 L + 5 mm
t = 0.022 61 + 5 mm
t = 6.342 mm

7.9375 mm or 5/16 inch for design used (standard)

THICKNESS OF THIRD DECK PLATING INSIDE LINE

REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 4,P.65

t = 0.02 L + 5 mm
t = 0.02 61 + 5 mm
t = 6.22 mm

6.35 mm or 1/4 inch for design used (standard)

NOTE: NO NEED TO ADJUST THE SPACING

THICKNESS OF PLATFORM DECK PLATING

REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 4,P.65

t = 0.02 L + 5 mm
t = 0.02 61 + 5 mm
t = 6.22 mm

6.35 mm or 1/4 inch for design used (standard)

SECTION 6: DOUBLE BOTTOM

DEPTH OF CENTER GIRDER

REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 6,P.74

h = L + 42 d + 530 mm
h = 61 + 42 2.5 + 530 mm
 SCANTLING CALCULATION

h = 696 mm

Adopt 760 mm for designed used

THICKNESS OF CENTER GIRDER

REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 6,P.74
a.) for 0.4 L amidships

t = 0.065 L + 5.5 mm
t = 0.065 61 + 5.5 mm
t = 9.465 mm

9.525 mm or 3/8 inch for design used (standard)

b.) for 0.1 L at ends

t = 0.045 L + 5.5 mm
t = 0.045 61 + 5.5 mm
t = 8.245 mm

9.525 mm or 1/4 inch for design used (standard)

SECTION 6: DOUBLE BOTTOM

CENTER GIRDERS
REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 6,P.74

h = L + 42 d + 530 mm
h = 61 + 42 2.5 + 531 mm
h = 697 mm

THICKNESS OF CENTER GIRDER

REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 6,P.74

a.) for 0.4 L amidships

t = 0.065 L + 5.5 mm
t = 0.065 61 + 5.5 mm
t = 9.465 mm

9.525 mm or 1/4 inch for design used (standard)

b.) for 0.1 L at ends

t = 0.045 L + 5.3 mm �^2
 SCANTLING CALCULATION

�^2
t = 0.045 61 + 5.3 mm
t = 8.045 mm

9.525 mm or 1/4 inch for design used (standard)

DUCT KEELS
SECTION MODULUS
REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 6,P.75

w = 22 s d cm³
w = 22 0.5588 2.5 0.76 ² cm³
w = 17.752 cm³

TRANSVERSE FRAMING -THICKNESS PLATE FLOORS

REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 6,P.77
�^2

t = 0.03 L + 5 s + 2.6
t = 0.03 61 + 5 0.5588 + 2.6
t = 7.224 mm

Adopt 8 mm for designed used

SECTION MODULUS OF STIFFINERS

REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 6,P.77 √ℎ

w = 5.5 s h cm³
w = 5.5 0.5588 3.9 0.76 cm³
w = 9.11 cm³

PLANE BULKHEAD PLATING

THICKNESS OF THE PLANE WATERIGHT BULKHEAD

REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 11,P.118 �_1

t = 3.2 s + 2.3 mm
t = 3.2 0.5588 1.685 + 2.3 mm
t = 5.31 mm

Adopt 6.35 mm for designed used

SECTION MODULUS OF BOTTOM FRAMES OF BRACKET FLOORS

 SCANTLING CALCULATION

REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS

CHAPTER E,SECTION 6,P.78

w = ( 15 2.5 ) sd cm³
w = 15 2.5 2.5 8.7313 cm³
w = 76.398 cm³

TRANSVERSE FRAMING-INNER BOTTOM PLATING AND MARGIN PLATE

REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 6,P.79

t = 0.04 L 5 s + 2.1 mm
t = 0.04 61 5 0.5588 + 2.1 mm
t = 8.9174 mm

9.525 mm or 1/4 inch for design used (standard)

for 0.4 l amidship but not is less than 6mm

t = 0.055 L + 5.8 mm
t = 0.055 61 + 5.8 mm
t = 9.155 mm
9.525 mm or 1/4 inch for design used (standard)

LONGITUDINAL FRAMING - BOTTOM GIRDERS

REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 6,P.74

h = L + 42 d + 530 mm
h = 61 + 42 0 + 530 mm
h = 591 mm

Adopt 760 mm for designed used

The thickness of the center girden is not to be less than

a.) for 0.4 L amidships

t = 0.065 L + 5.5 mm
t = 0.065 0 + 5.5 mm
t = 5.5 mm

6.35 mm or 1/4 inch for design used (standard)

b.) for 0.1 L at ends

 SCANTLING CALCULATION

t = 0.045 L + 5.5 mm
t = 0.045 0 + 5.5 mm
t = 5.5 mm

9.525 mm or 1/4 inch for design used (standard)

LONGITUDINAL FRAMING-BOTTOM LONGITUDINAL

STANDARD SPACING OF BOTTOM LONGITUDINAL
REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 6,P.81
1
s = 2.3 L + 550 mm
s = 2.3 61 + 550 mm
s = 690.3

2
s = 2 L + 510 mm
s = 2 61 + 510 mm
s = 632

3
s = 720 ( L / 100 )^¼ mm
s = 720 61 / 100 )^¼ mm
s = ### mm
Adopt 558.8 millimeters for designed used

SECTION MODULUS OF BOTTOM LONGITUDINAL

REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 6,P.81

W = 11.5 C s d ɭ²
W = 11.5 1 0.632 2.5 1.21
W = 21.986 cm³

SECTION MODULUS OF INNER BOTTOM LONGITUDINAL

REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 6,P.82

W = 21.986 x 85%
W = 18.688 cm³

LONGITUDINAL FRAMING - THICKNESS INNER BOTTOM PLATING

REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 6,P.82

for 0.4L amidship but is not less than 6mm

 SCANTLING CALCULATION

t = 0.04 L 5 s + 2.1 mm
t = 0.04 61 5 0.632 + 2.1 mm
t = 9.8104 mm
11.11 mm or 7/16 inch for design used (standard)

For machinery spaces

REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 6,P.82

t = 0.055 L + 5.8 mm
t = 0.055 61 + 5.8 mm
t = 9.155 mm

9.525 mm or 3/8 inch for design used (standard)

THCKNESS OF THE MARGIN PLATES

REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 6,P.83

t = 0.04 L 5 s + 2.1 mm
t = 0.04 61 5 0 + 2.1 mm
t = 2.1 mm
3.175 mm or 1/18 inch for design used (standard)

for 0.4 l amidship but not is less than 6mm

t = 0.055 L + 5.8 mm √
t = 0.055 61 + 5.8 mm
t = 9.155 mm

9.525 mm or 1/4 inch for design used (standard)

SECTION 7 SIDE FRAMING

MAIN FRAMES
REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 7,P.85

SECTION MODULUS OF MAIN FRAMES

w = C Cı s d ɭ² cm³
w = 6.0158 1 0.5588 2.5 1.82² cm³
w = 27.838 cm³

Coefficient
C = 2 + d/D x 0.65
 SCANTLING CALCULATION

1.45 D/ ɭ
C = 2 + 2.5/ 3.6 x 0.65
1.45 1.043
C = 6.0158

Cı = 1.08 0.01 D
Cı = 1.08 0.01 3.6
Cı = 1.044

FRAMES IN TWEEN DECKS AND SUPERSTRUCTURE

REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 7,P.87

C = 0.7 + 4 (d / D)
C = 0.7 + 4 2.5 / 3.6
C = 3.478 cm³

I.I LOWER TWEENDECK

W = C Cı S d ɭ D cm³
W = 3.478 1.25 0.5588 2.5 2.6 1.897 cm³
W = 29.959 cm³

I.II SUPERSTRUCTURE SPACES

W = C Cı S d ɭ D cm³
W = 3.478 1.25 0.5588 2.5 2.3 1.897 cm³
W = 26.50 cm³

II.I UPPER TWEENDECK SPACES BELOW SUPERSTRUCTURE

W = C Cı S d ɭ D cm³
W = 3.478 1 0.5588 2.5 2.6 1.897 cm³
W = 23.97 cm³

II.I UPPER TWEENDECK SPACES BELOW SUPERSTRUCTURE

W = C Cı S d ɭ D cm³
W = 3.478 1 0.5588 2.5 2.3 1.897 cm³
W = 21.20 cm³

III.I UPPER TWEENDECK SPACES OUTSIDE THE SUPERSTRUCTURE

W = C Cı S d ɭ D cm³
W = 3.478 0.95 0.5588 2.5 2.6 1.897 cm³
W = 22.77 cm³

III.II UPPER TWEENDECK SPACES OUTSIDE THE SUPERSTRUCTURE

W = C Cı S d ɭ D cm³
W = 3.478 0.95 0.5588 2.5 2.3 1.897 cm³
 SCANTLING CALCULATION

W = 20.14 cm³

III.II UPPER TWEENDECK SPACES OUTSIDE THE SUPERSTRUCTURE

W = C Cı S d ɭ D cm³
W = 3.478 0.8 0.5588 2.5 2.6 1.897 cm³
W = 19.17 cm³

IV.I IN POOP
W = C Cı S d ɭ D cm³
W = 3.478 0.7 0.5588 2.5 2.3 1.897 cm³
W = 14.84 cm³

IV.II IN POOP
W = C Cı S d ɭ D cm³
W = 3.478 0.7 0.5588 2.5 2.6 1.897 cm³
W = 16.777 cm³
V.I IN BRIDGE
W = C Cı S d ɭ D cm³
W = 3.478 0.6 0.5588 2.5 2.3 1.897 cm³
W = 12.721 cm³

V.I IN BRIDGE
W = C Cı S d ɭ D cm³
W = 3.478 0.6 0.5588 2.5 2.3 1.897 cm³
W = 12.721 cm³

SECTION MODULUS OF WEB FRAMES

REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 7,P.88

W' = 0.2 n C W
W' = 0.2 1 4.4 27.838
W' = 24.497 cm³

SECTION 8 DECK FRAMING

WEATHER STRENGTH DECK

REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 7,P.87

h = 0.0072 L + ( d / )
h = 0.0072 61 + 0.7 0.21 m
h = 0.929 m

FORECASTLE DECKAND WEATHER STRENGTH DECK FORWARD OF 0.075 FROM F.P

REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
 SCANTLING CALCULATION

CHAPTER E,SECTION 8,P.91

h = 0.929 + 20%
h = 1.1292 m

FORECASTLE DECKAND WEATHER STRENGTH DECK BETWEEN OF 0.075 FROM F.P

REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 8,P.91

h = 0.929 + 10%
h = 1.029 m

DECK CARGO AREA OF WEATHER STRENGTH DECK

REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 8,P.91

h = 0.929 + 0.3
h = 1.229 m
DECKS CARRYING HANGING MEAT CARGO
REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 8,P.91

h = 0.929 + 0.55
h = 1.479 m

THE LOWER DECKS .PLATFORMDECKS OR DECK BELOW SUPERSTRUCTURE DECK F

REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 8,P.91

h = 0.0072 L + ( d / )
h = 0.0072 61 + 0.7 0.21 m
h = 0.929 m

Adopt 1 m for designed used

The same as the required by water head of the weather strength deck but not gr

STRENGTH DECK IN A WAY OF DECK HOUSES FOR ACCOMODATION OR STORE SPA

REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 8,P.91

h = 0.0072 L + ( d / )
h = 0.0072 61 + 0.7 0.21
h = 0.929 m

SHORT BRIDGE DECK, POOP DECK AND TOP OF FIRST TIER HOUSES
REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
 SCANTLING CALCULATION

CHAPTER E,SECTION 8,P.91

h = 0.0072 L + ( d / )
h = 0.0072 61 + 0.7 0.21
h = 0.9292

h = 0.929 x 80%
h = 0.7434 m

DECKS ABOVE THE SUPERSTUCTURE DECK OR ABOVE THE TOP FIRST TIER DECKH
REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 8,P.91

h = 0.0072 L + ( d / )
h = 0.0072 61 + 0.7 0.21
h = 0.9292

h = 0.929 x 60%
h = 0.5575

SECTION MODULUS DECK BEAMS

REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 8,P.91

W = C s h ɭ² cm³
W = 6.67 6.5 0.929 1.83² cm³
W = 130.52 cm³

SECTION MODULUS OF DECK GIRDERS

REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 8,P.94

W = C b h ɭ² cm³
W = 6.2 6.5 0.929 1.83² cm³
W = 125.41 cm³

SECTION MODULUS OF HATCH GIRDERS (INCLUDING COAMIMGS) �^2

REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 8,P.96

W = 1.6 C h b ɭ² cm³
W = 1.6 6.2 0.929 1.8 1.83 cm³
W = 30.363 cm³
 SCANTLING CALCULATION

DECK LONGITUDINAL (LONGITUDINAL FRAMING)

REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 8,P.100

W = C s h ɭ² cm³
W = 18.062 0.929 0.929 2² cm³
W = 62.380 cm³

Coefficient
REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 8,P.101

C = k L + b
C = 0.042 61 + 15.5
C = 18.062

DECK TRANSVERSE
REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 8,P.102
W = 7 S h
W = 7 3.5 0.929 3.3489
W = 76.239 cm³

SECTION MODULUS OFC TWEENDECK LONGITUDINAL

REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 8,P.103

W = C s h ɭ² cm³
W = C 3.5 0.929 2 cm³

SECTION MODULUS OF STRENGTH DECK OR TWEENDECK TRANSVERSE

REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 8,P.103

W = 7 S h ɭ² cm³
W = 7 3.5 0.929 ɭ² cm³
 SCANTLING CALCULATION

STRENGTH DECK
for ships having one continous deck
REFERENCE:PRS RULES FOR THE CONST
CHAPTER E,SECTION 4,P.60

where:
= ( L
= 61
= 0.146

Z =
Z = 0.146
Z = 8.438

D
B +

13 +

0.0244

TION OF STEEL VESSELS 2017

where:
L = 61 m

TION OF STEEL VESSELS 2017

where:
L = 61 m
 SCANTLING CALCULATION

TION OF STEEL VESSELS 2017

TION OF STEEL VESSELS 2017

L = 61 m
s = 600 mm
d = 2.5 m

TION OF STEEL
√(𝑑/𝐿) VESSELS 2017

√(2.5/61)
where:
L = 61 m
s = 558.8 mm
d = 2.5 m
 SCANTLING CALCULATION

HELL PLATING)
√(𝑆/600)
FOR 0.075 FROM THE ENDS.
TION OF STEEL VESSELS 2017
√(600/600)

TION OF STEEL VESSELS 2017

where:
L = 61 m

TION OF STEEL VESSELS 2017

TION OF STEEL VESSELS 2017

where:
L = 61 m
 SCANTLING CALCULATION

TION OF STEEL VESSELS 2017

where:
L = 61 m

TION OF STEEL VESSELS 2017

where:
L = 61 m

TION OF STEEL VESSELS 2017

TION OF STEEL VESSELS 2017

where:
L = 61 m

TION OF STEEL VESSELS 2017

 SCANTLING CALCULATION

where:
L = 61 m

TION OF STEEL VESSELS 2017

where:
L = 61 m

TION OF STEEL VESSELS 2017

where:
L = 61 m

TION OF STEEL VESSELS 2017

where:
L = 61 m

TION OF STEEL VESSELS 2017

where:
L = 61 m
 SCANTLING CALCULATION

TION OF STEEL VESSELS 2017

TION OF STEEL VESSELS 2017

TION OF STEEL VESSELS 2017

 SCANTLING CALCULATION

�^2

TION OF STEEL VESSELS 2017

where:
L = 61 m m
0.76 m m
s = 0.5588 m m

TION OF STEEL VESSELS 2017

mm where: �^2
mm L = 13 m
s = 0.5588 m

TION OF STEEL VESSELS 2017

√ℎ=
where:
L = 61 m
0.76 mm
s = 0.5588 m

TION OF STEEL VESSELS 2017

�^2

where: �^2
1.685
 SCANTLING CALCULATION

TION OF STEEL VESSELS 2017

where:
ɭ¹ 2.5
sd 1.397

GIN PLATE
TION OF STEEL VESSELS 2017

where:
L= 61

TION OF STEEL VESSELS 2017

where:
L = 61 m
d= 2.5 m
 SCANTLING CALCULATION

TION OF STEEL VESSELS 2017

TION OF STEEL VESSELS 2017

TION OF STEEL VESSELS 2017

TION OF STEEL VESSELS 2017

 SCANTLING CALCULATION

TION OF STEEL VESSELS 2017

TION OF STEEL VESSELS 2017

TION OF STEEL VESSELS 2017

√
 SCANTLING CALCULATION

TION OF STEEL VESSELS 2017

√
 SCANTLING CALCULATION

𝐷�

TION OF STEEL VESSELS 2017

TION OF STEEL VESSELS 2017

0.21 m

RD OF 0.075 FROM F.P

TION OF STEEL VESSELS 2017
 SCANTLING CALCULATION

𝐷�

𝐷�
EN OF 0.075 FROM F.P
TION OF STEEL VESSELS 2017

TION OF STEEL VESSELS 2017

𝐷�

TION OF STEEL VESSELS 2017

𝐷�

PERSTRUCTURE DECK FOR ACCOMODATION OR STRORES SPACES

TION OF STEEL VESSELS 2017

0.21 m

𝐷�
ength deck but not greater than 1m

DATION OR STORE SPACES

TION OF STEEL VESSELS 2017

0.21

HOUSES
TION OF STEEL VESSELS 2017
 SCANTLING CALCULATION

0.21

TOP FIRST TIER DECKHOUSES

TION OF STEEL VESSELS 2017

0.21

TION OF STEEL VESSELS 2017

TION OF STEEL VESSELS 2017

TION OF STEEL VESSELS 2017

 SCANTLING CALCULATION

TION OF STEEL VESSELS 2017

TION OF STEEL VESSELS 2017

TION OF STEEL VESSELS 2017

TION OF STEEL VESSELS 2017

RANSVERSE
TION OF STEEL VESSELS 2017
 SCANTLING CALCULATION

ng one continous deck: A = �_1

�
RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS 2017
R E,SECTION 4,P.60

/ � 75 ) ^ 4/3
/ � 75 ^ 4/3
�

L/D ( d + � 0.015 L )
16.94 2.5 + 0.015 61

�_1= �𝑧−�
𝐴_0/�
0.2
(𝑡_0+0.2 𝐴_0/�)
3.6
0.2 674.05 mm
SECTION MODULUS OF BOTTOM LONGITUDINAL
REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 6,P.81

W = 21.9857 cm³

FRAME SPACING = 558.8 mm

55.88 cm
22 inch
LONGITUDINAL BOTTOM FRAMING
REFERENCE:PRS RULES FOR THE CONSTRUCTION AND CLASSIFICATION OF STEEL VESSELS
CHAPTER E,SECTION 3,P.55

THICKNESS = 6.3 mm
1/4
METRIC

SECTION MODULUS 21.9857 cm³

SCANTLING THICKNESS 6.35 mm 0.635 cm
WEB 4 inch 10.16 cm
PLATING 3 1/2 inch 8.89 cm
THICKNESS 1/4 inch 0.635 cm
FRAME SPACING 558.80 mm 55.88 cm

SCANTLING MEMBER SIZE (S) AREA (A) dg (Y) adg (aY) adg² (aY)² I = ½ bh³
LONGITUDINAL BOTTOM 55.88 x 0.635 35.484 11.266 399.7643 4503.787
BOTTOM LONGITUDINAL FRAME 8.89 x 6.35 x 1.27 14.516 7.7978 113.1936 882.661 2765.997
� FA 50.000 512.9579 5386.448
2765.9966
8152.445

NEW dg = adg
a

512.958
50.000

= 10.2591788

NEW ICG = � adg² NEW adg²

8152.445 5262.527
= 2889.918

TOP ''C'' = 10.80 NEW dg

 10.80 10.25918
= 0.54

NEW a(dg)² = 50.000 x NEW dg ²

50.000 x 105.251
= 5262.527

SM ( W) = NEW ICG
C
2889.918
0.54

= 5393.437

english system
SECTION MODULUS 21.9857 cm³ 1.341655 inch ³
SCANTLING THICKNESS 1/4 inch 0.025 cm
WEB 4 inch 10.16 cm
PLATING 3 1/2 inch 8.89 cm
THICKNESS 1/4 inch 0.635 cm
FRAME SPACING 558.80 mm 22 inch

SCANTLING MEMBER SIZE (S) AREA (A) dg (Y) adg (aY) adg² (aY)² I = ½ bh³
LONGITUDINAL BOTTOM 55.88 x 0.635 5.500 0.688 3.78125 2.600
BOTTOM LONGITUDINAL FRAME 8.89 x 6.35 x 1.27 1.310 3.34 4.37409 14.605 1.17
� FA 6.810 8.15534 17.205
1.17
18.375

NEW dg = adg
a

8.155
6.810

= 1.1975536

NEW ICG = � adg² NEW adg²

18.375 9.766
= 8.608

TOP ''C'' = 10.19 NEW dg

10.19 1.197554
= 8.99

NEW a(dg)² = 6.810 x NEW dg ²

 6.810 x 1.434
= 9.766

SM ( W) = NEW ICG
C
8.608
8.99

= 0.958
OF STEEL VESSELS 2017

OF STEEL VESSELS 2017

BOTTOM LONGITUDINAL FRAME
SECTION MODULUS = 21.9857 cm³ 1.3417 inch ³
SCANTLING THICKNESS = 1/4 inch

DIMENSION
PLATE = 558.8 mm 22 inch
WEB = 3 inch
FLANGE = 2 inch
THICKNESS = 1/4 inch

SCANTLING MEMBER SIZE (S) AREA (A) Dg (Y) adg (aY) adg² (aY)²
BOTTOM LONGITUDINAL 22 x ¼ 5.50 0.688 3.781 2.60
BOTTOM LONGITUDINAL L3 x 2 x ¼ 1.19 2.26 2.68583 6.06
FRAME
FA 6.69 adg 6.467 8.66
+ 1.09
F(adg)² 9.75

New dg adg 6.467

= = ans =
a 6.69

New a(dg)²
= FA x 0.9667 = 6.69 x 0.9667 ans =

New ICG = adg² - New adg² = 9.75 x 6.252 ans =

TOP "C " = 3.25 - 0.9667 ans =

SM (W) New ICG 3.500

= = ans =
C 2.283

SM PERCENT = 1.533 - 1.3417

0.26 x 100 %
ans = 25.65 %

INNER BOTTOM LONGITUDINAL

SECTION MODULUS = 18.687845 cm³ 1.1404 inch ³
SCANTLING THICKNESS = 1/4 inch

DIMENSION
PLATE = 558.8 mm 22 inch
WEB = 3 inch
FLANGE = 2 1/2 inch
THICKNESS = 1/5 inch
 SCANTLING MEMBER SIZE (S) AREA (A) Dg (Y) adg (aY) adg² (aY)²
BOTTOM LONGITUDINAL 22 x ¼ 5.50 0.688 3.781 2.60
BOTTOM LONGITUDINAL L3 x 2 ½ x 5/16 0.996 2.36 2.352552 5.56
FRAME
FA 6.50 adg 6.134 8.16
+ 0.907
F(adg)² 9.06

New dg = adg = 6.134 ans =

a 6.50

New a(dg)² = FA x 1.0631 = 6.50 x 0.9442 ans =

New ICG = adg² - New adg² = 9.06 - 5.792 ans =

TOP "C " = 3.25 - 0.9442 ans =

SM (W) = New ICG = 3.272 ans =

C 2.306

SM PERCENT = 1.419 - 1.1404

0.32 x 100 %
ans = 31.75

DECK LONGITUDINAL
SECTION MODULUS = 62.380 cm³ 3.8067 inch ³
SCANTLING THICKNESS = 3/8 inch

DIMENSION
PLATE = 558.8 mm 22 inch
WEB = 4 inch
FLANGE = 3 1/2 inch
THICKNESS = 3/8 inch

SCANTLING MEMBER SIZE (S) AREA (A) Dg (Y) adg (aY) adg² (aY)²
BOTTOM LONGITUDINAL 22 x3 3/8 8.25 1.547 12.762 19.74
BOTTOM LONGITUDINAL L4 x 3 ½ x3/8 2.67 3.17 8.45055 26.75
FRAME
FA 10.92 adg 21.212 46.49
+ 4.18
F(adg)² 50.67
 New dg = adg = 21.212 ans =
a 10.92

New a(dg)² = FA x 1.0631 = 10.92x 1.9425 ans =

New ICG = adg² - New adg² = 50.67 x 41.205 ans =

TOP "C " = 4.38 - 1.9425 ans =

SM (W) = New ICG = 9.462 ans =

C 2.432

SM PERCENT = 3.890 - 3.8067

0.32 x 100 %
ans = 31.61

DECK TRANSVERSE
SECTION MODULUS = 5.6 cm³ 0.3410 inch ³
SCANTLING THICKNESS = 3/8 inch

DIMENSION
PLATE = 558.8 mm 22 inch
WEB ] 4 inch
FLANGE = 3 1/2 inch
THICKNESS = 3/8 inch

SCANTLING MEMBER SIZE (S) AREA (A) Dg (Y) adg (aY) adg² (aY)²
BOTTOM LONGITUDINAL 22 x3 3/8 8.25 1.547 12.762 19.74
BOTTOM LONGITUDINAL L4 x 3 ½ x3/8 2.67 3.17 8.45055 26.75
FRAME
FA 10.92 adg 21.212 46.49
+ 4.18
F(adg)² 50.67

New dg = adg = 21.212 ans =

a 10.92

New a(dg)² = FA x 1.0631 = 10.92x 1.9425 ans =

New ICG = adg² - New adg² = 50.67 x 41.205 ans =

 TOP "C " = 4.38 - 1.9425 ans =

SM (W) = New ICG = 9.462 ans =

C 2.432

SM PERCENT = 3.890 - 0.3410

1.21 x 100 %
ans = 121.01
I =1/12 bh³

1.09

0.9667

6.252

3.500

2.283

1.533 inch ³ / 25.808 cm³

 I = 1/12 bh³

0.907

0.9442

5.792

3.27153809567426

2.306

1.419 inch ³ / 23.88928 cm³

I = 1/12 bh³

4.18
 1.9425

41.205

9.462

2.432

3.890 inch ³ / 65.49074 cm³

I = 1/12 bh³

4.18

1.9425

41.205

9.462
2.432

3.890 inch ³ / 65.49074 cm³

BOTTOM LONGITUDINAL FRAME
SECTION MODULUS = 21.9857 cm³ 1.3058 inch ³
SCANTLING THICKNESS = 6.35 mm 0.64 cm
WEB = 4 inch 10.16 cm
PLATING = 3 1/2 inch 8.89 cm
THICKNESS = 1/3 inch 0.79 cm
FRAME SPACING = 558.8 mm 55.88 cm
24 inch 60.96 cm

SCANTLING MEMBER SIZE (S) AREA (A) dg (Y) adg (aY) adg² (aY)²
BOTTOM LONGITUDINAL 55.88x ¼ 48.39 0.397 19.204 7.62
BOTTOM LONGITUDINAL L4x 3 1/2 x 5/16 14.52 7.95 115.444 918.10
FRAME
FA 62.90 adg 134.647 925.72
+ 776.9653
F(adg)² 1702.69

New dg adg 134.647

= = ans =
a 62.90

New a(dg)²
= FA x 0.9667 = 37.73 x 0.8266 ans =

New ICG = adg² - New adg² = 957.02x 25.785 ans =

TOP "C " = 10.80 - 2.1406 ans =

SM (W) New ICG 1414.468

= = ans =
C 8.654

SM PERCENT = 163.438 - 21.9857

6.43 x 100 %
ans = 643.38 %

BOTTOM LONGITUDINAL FRAME

SECTION MODULUS = 21.9857 cm³ 1.3417 inch ³
SCANTLING THICKNESS = 6.35 mm 0.64 cm
WEB = 4 inch 10.16 cm
PLATING = 3 1/2 inch 8.89 cm
THICKNESS = 1/3 inch 0.79 cm
24 inch 60.96 cm

SCANTLING MEMBER SIZE (S) AREA (A) Dg (Y) adg (aY) adg² (aY)²
BOTTOM LONGITUDINAL 55.88x ¼ 48.39 0.318 15.363 4.88
BOTTOM LONGITUDINAL L4x 3 1/2 x 5/16 14.52 7.96 115.498 918.97
FRAME
FA 62.90 adg 130.861 923.84
 + 9.0424
F(adg)² 932.89

New dg adg 130.861

= = ans =
a 62.90

New a(dg)²
= FA x 0.9667 = 37.73 x 0.8266 ans =

New ICG = adg² - New adg² = 957.02x 25.785 ans =

TOP "C " = 10.80 - 2.0804 ans =

SM (W) New ICG 660.649

= = ans =
C 8.715

SM PERCENT = 75.809 - 21.9857

2.45 x 100 %
ans = 244.81 %
I = ½ bh³

776.97

2.1406

288.219

1414.47

8.654

163.438 cm³ / 10.008 inch ³

4.02 inch ³ 65.87598

I = ½ bh³

9.04
2.0804

272.238

660.65

8.715

75.809 cm³ / 4.642 inch ³