E-ATM300 Field Configuration Tool

(EFCT)

Installation and Operation

User Guide

Visit the Andrew tab on the Commscope website at

www.commscope.com to download latest firmware (soft-
ware) and antenna definition file before initial installation.

Register online to receive email notifications of file updates.

Andrew, A CommScope Company www.commscope.com/andrew

Customer Support Center Visit our Web site at aw.commscope.com or contact your local Andrew representative for more information.
North America: +1-800-255-1479, Option 1 © 2009 CommScope, Inc. All rights reserved.
Andrew Wireless Solutions is a trademark of CommScope. All trademarks identified by ® or ™ are registered
International: +1-779-435-6500, Option 1 trademarks or trademarks, respectively, of CommScope. This document is for planning purposes only and is not
intended to modify or supplement any specifications or warranties relating to Andrew products or services.

Bulletin 639556 • Revision C • December 2008

Table
of Contents

Introduction ......................................................................................................... iii

Section 1 Initial Installation of EFCT on the PC ...............................................1-1
Section 2 Operation ..........................................................................................2-1
Section 3 Updating the Antenna Definition File ...............................................3-1
Section 4 Error Messages ..................................................................................4-1

Bulletin 639556 • Revision C December 2008 i

Table of Contents E-ATM300 Field Configuration Tool (EFCT)

This page intentionally left blank.

ii December 2008 Bulletin 639556 • Revision C

Introduction

The E-ATM300 Field Configuration Tool (EFCT) is a software tool that controls the E-ATM300
actuator specifically designed for the Ericsson RBS controller, which uses the Ericsson
proprietary protocol to control the actuator. The EFCT resides on a PC and allows the user to
communicate tilt commands to the actuator through an ATC200-LITE-USB controller.
Note that the E-ATM300 EFCT has the following limitations:
• Communicates with one actuator at a time directly connected to the controller by a con-
trol cable. The Ericsson RBS controller only controls one actuator per sector. Therefore
daisy chaining is not recommended.
• Works only over a serial port and not a USB port.
• Only use the EFCT software and not the ATCLite software.

Bulletin 639556 • Revision C December 2008 iii

 E-ATM300 Field Configuration Tool (EFCT)

Notices and Precautions

IMPORTANT
Before installing the EFCT Tool to operate the
ATC200-LITE-USB controller, please DOWNLOAD
the latest antenna definition file and controller
software from the Commscope web site at
www.commscope.com. Please register online to
receive E-mail notifications for software updates.

WARRANTY NOTICE
Proper installation procedures must be followed when
installing and operating RET equipment. Failure to assure
installations are done properly by trained installation
personnel and to follow procedures discussed in this bulletin
may cause warranty for such products to be void.
Andrew requires that all RET installations be pre-tested
and configured prior to installation. Failure to conduct pre-
test and pre-installation procedures defined by Andrew will
void warranty.

SAFETY NOTICE
The installation, maintenance, or removal of an antenna
requires qualified, experienced personnel. Andrew
installation instructions are written for such installation
personnel. Antenna systems should be inspected once
a year by qualified personnel to verify proper installation,
maintenance, and condition of equipment.
Andrew disclaims any liability or responsibility for the results
of improper or unsafe installation practices.

Do not install near power lines. Do not install on a wet or Wear shoes with rubber soles
Power lines, telephone lines, windy day or when and heels. Wear protective
and guy wires look the same. lightning or thunder is clothing including a
Assume any wire or line can in the area. Do not use long-sleeved shirt and rubber
electrocute you. metal ladder. gloves.

Installation Training Available at Andrew Institute

iv
ii December 2008
August 2008 Bulletin 639556 • Revision C
B
Section 1
Initial Installation of EFCT Software on the PC

The installation program is obtained from the CommScope website (www.commscope.com):

go to Andrew→Products→Antennas→Base Station Antenna Systems→Teletilt RET
System→Downloads→Teletilt® RET Products Software, Firmware, Tools, and Manuals.
Download the zip file, E-FCTSetup, to the Desktop of the PC and expand the zip file.
Begin the installation by double-clicking on E-FCTSetup.msi.
The following screens show the installation process.

1 2

3 4
Shortcut Icon for EFCT on Desktop.

Bulletin 639556 • Revision C December 2008 1-1

Section 1–Initial Installation of EFCT Software on the PC E-ATM300 Field Configuration Tool (EFCT)

This page intentionally left blank.

1-2 December 2008 Bulletin 639556 • Revision C

Section 2
Operation

Typical setup:

Serial cable to PC (USB cable

1 cannot be used with EFCT.) 2
Controller
Click on icon
to start EFCT
program.

Power Actuator (Note: Actua-

Supply tor can be attached to
controller at any time.)

3 4

Wait for initialization.

Bulletin 639556 • Revision C December 2008 2-1

Section 2–Operation E-ATM300 Field Configuration Tool (EFCT)

5 6

Searching for actuator. Actuator found.

(Note: If not previously configured, Current Antenna
Model window is blank.)

7 8 Slider

Set Tilt

Choose correct antenna model type. Change tilt (drag slider and click Set Tilt button).

2-2 December 2008 Bulletin 639556 • Revision C

Section 3
Updating the Antenna Definition File

EFCT uses an antenna definition file to provide the pull-down menu listing the antenna models with
their electrical tilt ranges. If an antenna is missing from the list, it is necessary to update the antenna
definition file.
• To download the latest antenna definition file from the CommScope website (www.commscope.
com), go to: Andrew→Products→Antennas→Base Station Antenna Systems→Teletilt RET
System→Downloads→Antenna Definition Files.
• Locate the Andrew firmware on the Antenna Definition Files page. Click on the Andrew Antenna
Definition File hyperlink to download the latest data file.

Bulletin 639556 • Revision C December 2008 3-1

Section 3–Updating the Antenna Definition File E-ATM300 Field Configuration Tool (EFCT)

Choose the save option, and save the zip file in the folder where the EFCT program was installed
(default: C:→Program files→Andrew Corporation→E-ATM300 Field Configuration Tool).

Old File
New File

Extract the antenna definition file to the same folder and delete the old file. Note: The antenna defini-
tion file always begins with RET-AN-AT and the latest revision will have the highest number following
this prefix.
If EFCT is open, close it and click on the EFCT icon to restart the program. If EFCT is left open, it will
not access the new antenna definition file.

3-2 December 2008 Bulletin 639556 • Revision C

Section 4
Troubleshooting

Error/Symptom Possible Cause Remedy

No recognized Antenna The actuator was previously configured Update the antenna definition file (see Section 4).
Model? with an antenna model not in the current
antenna definition file.
The antenna definition file is missing. Restore the antenna definition file (see Section 4).

Not connected The actuator is not connected. Check connection.

Not using the Ericsson special actuator. Use appropriate actuator.

Problem opening port? Something is already using the COM port. Make sure only one EFCT is running.
Make sure nothing else is using the same COM port.
Desired Antenna Model is Antenna definition file is outdated or cor- Update the antenna definition file (see Section 4).
not found in pull-down list rupted.
No model in antenna Actuator not connected to controller. Verify actuator is properly connected to the controller.
model window EFCT program does not work with USB Use the serial cable to connect the controller to the PC
cable. (USB cable will not work with E-ATM300 actuator).

Incorrect tilt range or Corrupted antenna definition file. Update the antenna definition file (see Section 4).
same tilt for all antenna
models
Device scan does not find Used USB cable. Use serial cable.
actuator

Bulletin 639556 • Revision C December 2008 4-1

Section 4–Troubleshooting E-ATM300 Field Configuration Tool (EFCT)

This page intentionally left blank.

4-2 December 2008 Bulletin 639556 • Revision C