Scribd
Upload
625 views5 pages

A Study On Multimeter PDF

A multimeter is a very useful test instrument that can be used to measure voltage, current, resistance, and continuity in electrical circuits. It has different sockets to connect test leads for measuring these quantities in both DC and AC circuits. There are two main types - analog and digital. Digital multimeters are now more commonly used, as they have high input impedance and won't disrupt the circuit being tested. This document provides instructions on how to properly use a digital multimeter to measure resistance, voltage, current, test diodes and transistors.

Uploaded by

Nishanth.M nishu
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
625 views5 pages

A Study On Multimeter PDF

A multimeter is a very useful test instrument that can be used to measure voltage, current, resistance, and continuity in electrical circuits. It has different sockets to connect test leads for measuring these quantities in both DC and AC circuits. There are two main types - analog and digital. Digital multimeters are now more commonly used, as they have high input impedance and won't disrupt the circuit being tested. This document provides instructions on how to properly use a digital multimeter to measure resistance, voltage, current, test diodes and transistors.

Uploaded by

Nishanth.M nishu
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

A STUDY ON MULTIMETER

Multimeters are very useful test instruments. They are needed in every kind of robotic activity. Don’t ever
forget to carry this whenever you are going for a competition.

USE:
Multimeters can be used as an ammeter, a voltmeter, an ohmmeter; by operating a multi-position knob on
the meter. They can measure DC as well as AC (but you shall rarely require measuring an AC quantity in
robotics). There are also special functions in a multimeter like ‘Detecting a Short Circuit’, testing
transistors and some have additional features for measuring capacitance & frequency.

They are available in two types in market:

1.) Analog Multimeter

§ Analogue meters take a little power from the circuit under test to operate their pointer (a hand like in
a clock to indicate the reading).
§ They must have a high sensitivity of at least 20k /V or they may upset the circuit under test and give
an incorrect reading.

2.) Digital Multimeter


§ All digital meters contain a battery to power the display so they use virtually no power from the
circuit under test.
§ They have a digital display as shown.

There DC voltage ranges have a very high resistance (usually called input impedance) of 1M or more,
usually 10 M , and they are very unlikely to affect the circuit under test.

Here we will have discussion on digital multimeter (as they are commonly used).

There are three sockets of wire, the black lead is always connected into the socket marked COM, short
form for COMMON. The red lead is connected into the socket labeled V mA. The 10A socket is very
rarely used.

Measuring resistance with a multimeter

To measure the resistance of a component it must not be connected in a circuit. If you try to measure
resistance of components in a circuit you will obtain false readings (even if the supply is disconnected)
and you may damage the multimeter.
The techniques used for each type of meter are very different so they are treated separately:

Measuring resistance with a DIGITAL multimeter


1. Set the meter to a resistance range greater than you expect the resistance to be.
Notice that the meter display shows "off the scale" (usually blank except for a 1 on the left). Don't
worry, this is not a fault, it is correct - the resistance of air is very high!
2. Touch the meter probes together and check that the meter reads zero.
If it doesn't read zero, turn the switch to 'Set Zero' if your meter has this and try again.
3. Put the probes across the component.
Avoid touching more than one contact at a time or your resistance will upset the reading!
If the meter reads 1, this means that the resistance is more than the maximum which can be measured on
this range and you may need to switch to a new position, 2000 k or so, to take a reading.

Note: It is recommended purchasing a multimeter with a 'continuity' feature built in. This mode allows us
to 'tone' out circuits. In this mode, if you touch the two probes together (or there is a short circuit), you
should hear a tone indicating that there is a direct connection between one probe and the other (obviously
- you have them touching!). This feature is used countless times during trouble shooting.

Measuring Voltage with Voltmeter

1. Select a voltage range with a maximum greater than you expect the reading to be. If the reading goes
off the scale immediately disconnect and select a higher range.
2. Connect the red (positive +) lead to the point you where you need to measure the voltage
3. The black lead can be left permanently connected to 0V while you use the red lead as a probe to
measure voltages at various points. (The black lead can be fitted by using a crocodile clip.)
Similarly you can measure the current by choosing a suitable range. If it displays a ‘1’ at left, choose a
higher current range.

Testing a diode with a DIGITAL multimeter


§ Digital multimeters have a special setting for testing a diode, usually labeled with the diode symbol.
§ Connect the red (+) lead to the anode and the black (-) to the cathode. The diode should conduct and
the meter will display a value (usually the voltage across the diode in mV, 1000mV = 1V).

§ Reverse the connections. The diode should NOT conduct this way so the meter will display "off the
scale" (usually blank except for a 1 on the left).
Testing a transistor with a multimeter

Set a digital multimeter to diode test and an analogue multimeter to a low resistance range such as × 10
ohm as described above for testing a diode.
Test each pair of leads both ways (six tests in total):
§ The base-emitter (BE) junction should behave like a diode and conduct one way only.
§ The base-collector (BC) junction should behave like a diode and conduct one way only.
§ The collector-emitter (CE) should not conduct either way.
NOTE: Conducting in one way simply means it will behave as a short circuit and
The diagram shows how the junctions behave in an NPN transistor. The diodes are reversed in a PNP
transistor but the same test procedure can be used.
Some multimeters have a 'transistor test' function; please refer to the instructions supplied with the meter
for details.

Source : http://www.botskool.com/tutorials/electronics/general-electronics/
multimeter

You might also like