REF 610

Feeder Protection Relay

Technical Reference Manual - ANSI Version

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine
 1MRS 755535 Feeder Protection Relay REF 610
Issued: January 30, 2005 Technical Reference Manual - ANSI Version
Version: A

Content
1. Introduction ...............................................................................6
1.1. About this manual .........................................................................6
1.2. The use of the relay ......................................................................6
1.3. Features ........................................................................................6
1.4. Warranty ........................................................................................8
1.5. Revision history .............................................................................8
2. Safety information .....................................................................9
3. Instructions ..............................................................................10
3.1. Application ...................................................................................10
3.2. Requirements ..............................................................................10
3.3. Configuration ...............................................................................10
4. Technical description .............................................................13
4.1. Functional description .................................................................13
4.1.1. Product functions .............................................................13
4.1.1.1. Protection functions ............................................13
4.1.1.2. Inputs .................................................................13
4.1.1.3. Outputs ...............................................................14
4.1.1.4. Disturbance recorder ..........................................14
4.1.1.5. HMI .....................................................................14
4.1.1.6. Non-volatile memory ..........................................14
4.1.1.7. Self-supervision ..................................................14
4.1.1.8. Time synchronization .........................................15
4.1.2. Measurements .................................................................16
4.1.3. Configuration ....................................................................16
4.1.4. Protection .........................................................................18
4.1.4.1. Block diagram ....................................................18
4.1.4.2. Overcurrent protection .......................................19
4.1.4.3. Ground-fault protection ......................................20
4.1.4.4. Thermal protection for cables .............................21
4.1.4.5. Phase discontinuity protection ...........................26
4.1.4.6. Circuit-breaker failure protection ........................26
4.1.4.7. Arc protection .....................................................27
4.1.4.8. Auto-reclose function .........................................28
4.1.4.9. Inverse definite minimum time characteristics ...34
4.1.4.10.Settings ..............................................................46
4.1.4.11.Technical data on protection functions ..............58
4.1.5. Trip-circuit supervision .....................................................63

©Copyright 2004 ABB, Distribution Automation, Allentown, PA 3

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

4.1.6. Trip lockout function ........................................................ 64

4.1.7. Trip counters for circuit-breaker condition monitoring ...... 65
4.1.8. Indicator LEDs and operation target messages ............... 65
4.1.9. Demand values ................................................................ 65
4.1.10.Commissioning tests ........................................................ 66
4.1.11.Disturbance recorder ....................................................... 66
4.1.11.1.Function ............................................................. 66
4.1.11.2.Disturbance recorder data ................................. 66
4.1.11.3.Control and target of disturbance
recorder status ................................................... 67
4.1.11.4.Triggering .......................................................... 68
4.1.11.5.Settings and unloading ....................................... 68
4.1.11.6.Event code of the disturbance recorder ............. 68
4.1.12.Recorded data of the last events ..................................... 68
4.1.13.Communication ports ....................................................... 70
4.1.14.IEC 60870-5-103 remote communication protocol .......... 71
4.1.15.Modbus remote communication protocol ......................... 75
4.1.15.1.Protocol overview .............................................. 75
4.1.15.2.Profile of Modbus REF 610 ............................... 76
4.1.16.DNP 3.0 remote communication protocol ........................ 89
4.1.16.1.Protocol overview .............................................. 89
4.1.16.2.Protocol parameters of REF 610 ....................... 89
4.1.16.3.DNP 3.0 point list of REF 610 ............................ 89
4.1.16.4.DNP 3.0 device profile of REF 610 .................... 93
4.1.16.5.REF 610-specific DNP features ....................... 100
4.1.17.SPA bus communication protocol parameters ............... 103
4.1.17.1.Event codes ..................................................... 118
4.1.18.Self-supervision (IRF) system ........................................ 122
4.1.19.Relay parameterization .................................................. 123
4.2. Design description .................................................................... 124
4.2.1. Input/output connections ............................................... 124
4.2.2. Light sensor input connections ...................................... 129
4.2.3. Serial communication connections ................................ 129
4.2.4. Technical data ............................................................... 134
5. Application examples .......................................................... 139
5.1. Auto-reclose function ................................................................ 139
5.1.1. Fast tripping and initiation of shot 1 using two
protection stages .......................................................... 139
5.1.2. Fast tripping and initiation of shot 1 using pickup signals 140
5.1.3. Selecting adaptive sequence length .............................. 141
5.2. Arc protection ............................................................................ 142
5.2.1. Arc protection with one REF 610 relay .......................... 142

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

5.2.2. Arc protection with several REF 610 relays ...................144

5.2.3. Arc protection with several REF 610 relays and
one REA 101 ..................................................................145
6. Ordering information ............................................................146
7. Revision History of REF 610 .................................................148
7.1. Revision identification ................................................................148
7.2. Changes and additions to earlier released revision A................148
8. References .............................................................................149
9. Abbreviations ........................................................................150
10.Check lists ............................................................................152

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

1. Introduction

1.1. About this manual

This manual provides thorough information on the protection relay REF 610
Revision B and its applications. For more information about the earlier revisions,
refer to section "Revision history of the REF 610".
Refer to the Operator’s Manual for instructions on how to use the
Human-Machine Interface (HMI) of the relay, also known as the Man-Machine
Interface (MMI), and to the Installation Manual for installation of the relay.

1.2. The use of the relay

The feeder protection relay REF 610 is a versatile multifunction protection relay
mainly designed to protect incoming and outgoing feeders in a wide range of feeder
applications.
REF 610 is based on a microprocessor environment. A self-supervision system
continuously monitors the operation of the relay.
The HMI includes a Liquid Crystal Display (LCD) which makes the local use of the
relay safe and easy.
Local control of the relay via serial communication can be carried out with a
computer connected to the front communication port. Remote control can be carried
out via the rear connector connected to the control and monitoring system through
the serial communication bus.

1.3. Features
• Three-phase non-directional overcurrent protection with definite-time or IDMT
(mode) characteristic, low-set element
• Three-phase non-directional overcurrent protection, high-set element
• Three-phase non-directional overcurrent protection, instantaneous element
• Non-directional ground-fault protection with definite-time or IDMT (mode)
characteristic, low-set element
• Non-directional ground-fault protection, high-set element
• Phase discontinuity protection
• Three-phase thermal overload protection for cables
• Arc protection
• two lens sensors for arc detection (optional)
• automatic reference level adjustment based on backlight intensity
• arc detection via a remote light signal
• Automatic reclosing 1...3 shots
• Circuit-breaker failure protection
• Trip counters for circuit-breaker condition monitoring
• Trip-circuit supervision with possibility to route the warning signal to a non-trip
output

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

• Trip lockout function

• Four accurate current inputs
• User-selectable rated frequency 50/60 Hz
• Three normally open trip output contacts
• Two change-over (Form C) non-trip output contacts and three additional change
over (Form C) non-trip output contacts on the optional I/O module
• Output contact functions freely configurable for desired operation
• Two galvanically isolated digital inputs and three additional galvanically isolated
digital inputs on the optional I/O module
• Disturbance recorder
• recording time up to 80 seconds
• triggering by one or several internal or digital input signals
• records four analogue channels and up to eight user-selectable digital channels
• adjustable sampling rate
• Non-volatile memory for
• up to 100 event codes with time stamp
• setting values
• disturbance recorder data
• recorded data of the five last events with time stamp
• number of AR shots and pickups/trips for protection elements
• operation target messages and LEDs showing the status at the moment of
power failure
• HMI with an alphanumeric LCD and maneuvering buttons
• eight programmable LEDs
• Operation target messages displayed in ANSI mode
• Multi-language support
• User-selectable password protection for the HMI
• Display of primary current values
• Demand values
• All settings can be modified with a PC
• Optical front communication connection: wirelessly or via cable
• Optional rear communication module with plastic fibre-optic, combined
fibre-optic (plastic and glass) or RS-485 connection for system communication
using the SPA-bus, IEC 60870-5-103 or Modbus (RTU and ASCII)
communication protocol
• Optional DNP 3.0 rear communication module with RS-485 connection for
system communication using the DNP 3.0 communication protocol.
• Battery back-up for real-time clock

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

• Battery charge supervision

• Continuous self-supervision of electronics and software.
• Detachable plug-in unit

1.4. Warranty
Please inquire about the terms of warranty from your nearest ABB representative.

1.5. Revision history

Version Date Remarks

A Jan. 30 2005 Modified for ANSI compliance from the original manual
version 1MRS755310 version A

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

2. Safety information

Dangerous voltages can occur on the connectors, even though the

auxiliary voltage has been disconnected.
! National and local electrical safety regulations must always be
followed.
The device contains components which are sensitive to electrostatic
discharge. Unnecessary touching of electronic components must
therefore be avoided.
The frame of the device has to be carefully grounded.
Only a competent electrician is allowed to carry out the electrical
installation.
Non-observance can result in death, personal injury or substantial
property damage.
Breaking the sealing tape on the upper handle of the device will result
in loss of warranty and proper operation will no longer be guaranteed.
When the plug-in unit has been detached from the case, do not touch
the inside of the case. The relay case internals may contain high voltage
potential and touching these may cause personal injury.

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

3. Instructions

3.1. Application
REF 610 is a versatile multifunction protection relay mainly designed for protection
of incoming and outgoing feeders in MV distribution substations. REF 610 can also
be used as back-up protection for motors, transformers and generators, in industrial
as well as in utility applications.
The large number of integrated protection functions, including three overcurrent
protection elements, non-directional ground-fault protection elements as well as
thermal protection, makes REF 610 a complete protection against overcurrent and
ground faults.
The optional arc protection for detection of arc situations in air insulated metal-clad
switchgears and the auto-reclose function for automatic clearing of overhead line
faults increase the range of applications further.
The large number of digital inputs and output contacts allows a wide range of
applications.

3.2. Requirements
To secure correct and safe operation of the relay, preventive maintenance is
recommended to be performed every five years when REF 610 is operating under
the specified conditions; see below and section Technical data.
When being used for real-time clock or recorded data functions, the battery should
be changed every five years.
Environmental conditions

• Recommended temperature range (continuous) -10...+55°C

• Limit temperature range (short-term) -40...+70°C
• Temperature influence on the operation accuracy of the 0.1%/°C
protection relay within the specified service temperature range
• Transport and storage temperature range -40...+85°C

3.3. Configuration
Setting and connection examples
The appropriate configuration of the output contact matrix enables the use of the
signals from the protection elements as contact functions. The pickup signals can be
used for blocking co-operating protection relays and signalling.
Fig. 3.3.-1 and Fig. 3.3.-2 represent REF 610 with the default configuration: all trip
signals are routed to trip the circuit breaker. In Fig. 3.3.-1, the residual current is
measured via a core-balance current transformer and the output contacts are
connected to enable the use of the auto-reclose function. In Fig. 3.3.-2, the residual
current is measured via a summation connection of the phase current transformers
and the output contacts are connected to enable the use of the trip lockout function.

10

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535

A
B
C +

+ +
52a 52b CS
CS T
C

52b 52a
(dc/ac)
U 52 52
aux
CLOSE TC

Downloaded from www.Manualslib.com manuals search engine

+ +
- - - -

D15 D14 D13 D12 D11 IRF SO1 SO4 PO3 PO2 PO1 SO5 SO4 SO3
X2.1 7 81 2 3 45 6 X3.1 6 5 4 3 2 1 21 22 23 24 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 16 17 18 19 20 21 22 23 24 X3.1

Fig. 3.3.-1 Connection diagram, example 1

(dc/ac)

Self-supervision IRF Optional

Optional Warning

SGB5 SGB4 SGB3 SGB2 SGB1 51P Pickup 1 1 1 1 1 1 1 1

11 11 11 11 11 Blocking Trip 2 2 2 2 2 2 2 2

50P-1 Pickup 3 3 3 3 3 3 3 3
Blocking Trip 4 4 4 4 4 4 4 4
12 12 12 12 12

50P-2 Pickup
5 5 5 5 5 5 5 5
Trip
Feeder Protection Relay

6 6 6 6 6 6 6 6

51N Pickup
7 7 7 7 7 7 7 7
Blocking Trip
13 13 13 13 13 8 8 8 8 8 8 8 8

50N Pickup 9 9 9 9 9 9 9 9
Blocking Trip
14 14 14 14 14 10 10 10 10 10 10 10 10

46 Pickup
11 11 11 11 11 11 11 11
Blocking Trip
15 15 15 15 15 12 12 12 12 12 12 12 12

49 Alarm
Trip 13 13 13 13 13 13 13 13
X5.1 14 14 14 14 14 14 14 14
Technical Reference Manual - ANSI Version

Light Sensor 1
Light Sensor 2 Arc 51P/51N Arc light output 23 23 23 23 23 23 23 23
9 9 9 9 9 External Arc Trip 22 22 22 22 22 22 22 22
X5.2
Optional
79

18 18 18 18 18 16 16 16 16 16 16 16 16
CB Position Open Open CB Command 17 17 17 17 17 17 17 17
19 19 19 19 19
CB Position Closed Close CB Command 19 19 19 19 19 19 19 19
16 16 16 16 16
AR Disable CB Reclosing Failed 20 20 20 20 20 20 20 20
17 17 17 17 17
20 20 20 20 20 CB Close Disable Shot Due 18 18 18 18 18 18 18 18
External AR Initiation Definite Trip Alarm 21 21 21 21 21 21 21 21

Trip Lockout

8 8 8 8 8
External Triggering
10 10 10 10 10
Reset Trip Lockout
6 6 6 6 6 15 15 15 15 15 15 15 15
External Trip External Trip

CB FAIL
7 7 7 7 7
External Triggering Trip
1 1 1 1 1
Indications Cleared
2 2 2 2 2 Output contacts unlatched
3 3 3 3 3 Memorized values cleared
4 4 4 4 4 Setting group selection
5 5 5 5 5 Time sync
SGF1...SGF5
SGL1...SGL8

ConnDiagr1REF610_a
REF 610

11
 12
L1
L2
L3
REF 610

+ +
CS
CS T
C

(dc/ac) 52b 52a

U
aux
52 52
CLOSE TC
+ +
- -

D15 D14 D13 D12 D11 IRF SO2 SO1 PO3 PO2 PO1 SO5 SO4 SO3
X2.1 7 81 2 3 45 6 X3.1 6 5 4 3 2 1 21 22 23 24 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 16 17 18 19 20 21 22 23 24 X3.1
(dc/ac)

Downloaded from www.Manualslib.com manuals search engine

Self-supervision IRF Optional
Optional Warning
SGR5 SGR4 SGR3 SGR2 SGR1 SGR8 SGR7 SGR6

SGB5 SGB4 SGB3 SGB2 SGB1 51P Pickup 1 1 1 1 1 1 1 1

11 11 11 11 11 Blocking Trip 2 2 2 2 2 2 2 2

Fig. 3.3.-2 Connection diagram, example 2

50P-1 Pickup 3 3 3 3 3 3 3 3
Blocking Trip 4 4 4 4 4 4 4 4
12 12 12 12 12

50P-2 Pickup
5 5 5 5 5 5 5 5
Trip
6 6 6 6 6 6 6 6

51N Pickup
7 7 7 7 7 7 7 7
Blocking Trip
13 13 13 13 13 8 8 8 8 8 8 8 8

50N Pickup 9 9 9 9 9 9 9 9
Blocking Trip
14 14 14 14 14 10 10 10 10 10 10 10 10

46 Pickup
11 11 11 11 11 11 11 11
Blocking Trip
15 15 15 15 15 12 12 12 12 12 12 12 12
Feeder Protection Relay

49 Alarm
Trip 13 13 13 13 13 13 13 13
X5.1 14 14 14 14 14 14 14 14
Light Sensor 1
Light Sensor 2 Arc 51P/51N Arc light output 23 23 23 23 23 23 23 23
9 9 9 9 9 External Arc Trip 22 22 22 22 22 22 22 22
X5.2
Optional
79

18 18 18 18 18 16 16 16 16 16 16 16 16
CB Position Open Open CB Command
19 19 19 19 19 17 17 17 17 17 17 17 17
CB Position Closed Close CB Command
16 16 16 16 16 19 19 19 19 19 19 19 19
AR Disable CB Reclosing Failed
17 17 17 17 17 20 20 20 20 20 20 20 20
CB Close Disable Shot Due
20 20 20 20 20 18 18 18 18 18 18 18 18
External AR Initiation Definite Trip Alarm
21 21 21 21 21 21 21 21
Technical Reference Manual - ANSI Version

AR Lockout
Trip Lockout

8 8 8 8 8
External Triggering
10 10 10 10 10 Trip Lockout
Reset
6 6 6 6 6 15 15 15 15 15 15 15 15
External Trip External Trip

CB FAIL
7 7 7 7 7 External Triggering Trip
1 1 1 1 1
2 2 2 2 2 Indications Cleared
3 3 3 3 3 Output contacts unlatched
Memorized values cleared
4 4 4 4 4
Setting group selection
5 5 5 5 5
Time sync

SGF1 ...SGF5
SFL1 ...SGL8

ConnDiagr2 REF610_a
1MRS 755535
 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

4. Technical description

4.1. Functional description

4.1.1. Product functions

4.1.1.1. Protection functions

The protection functions of REF 610 with their IEC symbols and IEEE device
numbers are presented in the table below:

Table 4.1.1.1-1 IEC symbols and IEEE device numbers

IEEE Device
Function description IEC symbol
No.
Three-phase non-directional overcurrent protection, I> 51P
low-set element
Three-phase non-directional overcurrent protection, I>> 50P-1
high-set element
Three-phase non-directional overcurrent protection, I>>> 50P-2
instantaneous element
Phase discontinuity protection ΔI> 46
Three-phase thermal overload protection for cables θ> 49
Non-directional ground-fault protection, low-set element I0> 51N
Non-directional ground-fault protection, high-set I0>> 50N
element
Arc protection ARC ARC
Circuit-breaker failure protection CBFP CBFAIL
Automatic reclosing 0→1 79
Lockout relay 86

For descriptions of the protection functions, refer to sections:

• 4.1.4.2. Overcurrent protection
• 4.1.4.3. Ground-fault protection
• 4.1.4.4. Thermal protection for cables
• 4.1.4.5. Phase discontinuity protection
• 4.1.4.6. Circuit-breaker failure protection
• 4.1.4.7. Arc protection
• 4.1.4.8. Auto-reclose function

4.1.1.2. Inputs
REF 610 is provided with four energizing inputs, two optional light sensor inputs,
two digital inputs and three optional digital inputs controlled by an external voltage.
Three of the energizing inputs are for the phase currents and one for the ground-fault
current. For details, refer to section Input/output connections and tables 4.1.4.10-7,
4.2.1-1 and 4.2.1-5. The functions of the digital inputs are determined with the
SGB switches.

13

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

4.1.1.3. Outputs
REF 610 is provided with three trip outputs (PO1, PO2 and PO3), two non-trip
outputs (SO1 and SO2) and three optional non-trip outputs (SO3, SO4 and SO5).
Switchgroups SGR1...8 are used for routing internal signals from the protection
elements, the external trip signal and signals from the auto-reclose function to the
desired non-trip or trip output. The minimum pulse length can be configured to be
40 or 80 ms and the trip outputs can all be configured to be latched.

4.1.1.4. Disturbance recorder

REF 610 includes an internal disturbance recorder which records the instantaneous
measured values, or the RMS curves of the measured signals, and up to eight
user-selectable digital signals: the digital input signals and the internal signals from
the protection elements. Any digital signal can be set to trigger the recorder on either
the falling or rising edge.

4.1.1.5. HMI
The HMI of REF 610 is equipped with six push-buttons, an alphanumeric
2x16 characters’ LCD, eight programmable target LEDs, three target LEDs with
fixed functionality, and an target LED for front communication. The
push-buttons are used for navigating in the menu structure and for adjusting setting
values.
An HMI password can be set to protect all user-changeable values from being
changed by an unauthorized person. The HMI password will remain inactive and
will thus not be required for altering parameter values until the default HMI
password has been replaced. Entering the HMI password successfully can be
selected to generate an event code. This feature can be used to indicate interaction
activities via the local HMI. For further information on the HMI, refer to the
Operator’s Manual.

4.1.1.6. Non-volatile memory

REF 610 can be configured to store various data in a non-volatile memory, which
will retain its data also in case of loss of auxiliary voltage (provided that the battery
has been inserted and is charged). Operation target messages and LEDs, disturbance
recorder data, event codes and recorded data can all be configured to be stored in the
non-volatile memory whereas setting values will always be stored in the EEPROM.

4.1.1.7. Self-supervision
The self-supervision system of REF 610 manages run-time fault situations and
informs the user about an existing fault. There are two types of fault targets: internal
relay fault (IRF) targets and warnings.
When the self-supervision system detects a permanent internal relay fault, which
will prevent relay operation, the green target LED (ready) will begin to blink. At the
same time, the IRF contact, which is normally picked up, will drop off and a fault
code will appear on the LCD. The fault code is numerical and identifies the fault
type.

14

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

INTERNAL FAULT
FAULT CODE :30

IntFault_a
Fig. 4.1.1.7.-1 Permanent IRF
In case of a warning, the relay will continue to operate with full or reduced
functionality and the green target LED (ready) will remain lit as during normal
operation. A fault target message (see Fig. 4.1.1.7.-2), with a possible fault code (see
Fig. 4.1.1.7.-3), will appear on the LCD indicating the type of fault. In case of a
warning due to an external fault in the trip circuit detected by the trip-circuit
supervision, or due to continuous light on the light sensor inputs, SO2 will be
activated (if SGF1/8=1).

WARNING
BATTERY LOW
Warning_a

Fig. 4.1.1.7.-2 Warning with text message

WARNING
FAULT CODE: 33
WarnREF610_a

Fig. 4.1.1.7.-3 Warning with numeric code

For fault codes, refer to section Self-supervision (IRF) system.

4.1.1.8. Time synchronization

Time synchronization of the relay’s real-time clock can be realized in two different
ways: via serial communication using a communication protocol or via a digital
input.
Any digital input can be configured for time synchronization and used for either
minute-pulse or second-pulse synchronization. The synchronization pulse is
automatically selected and depends on the time range within which the pulse occurs.
The time must be set once, either via serial communication or manually via the HMI.
If the synchronization pulse differs more than +/- 0.05 seconds for second-pulse or
+/- 2 seconds for minute-pulse synchronization from the relay’s real-time clock, the
synchronization pulse will be rejected.

15

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

Time synchronization is always triggered on the rising edge of the digital input
signal. The time is adjusted in steps of five milliseconds per synchronization pulse.
The typical accuracy achievable with time synchronization via a digital input is
+2.5...-2.5 milliseconds for second-pulse and +5...-5 milliseconds for minute-pulse
synchronization.
Note!
The pulse length of the digital input signal does not affect time synchronization.

4.1.2. Measurements
The table below presents the measured values which can be accessed through the
HMI:

Table 4.1.2-1 Measured values

Indicator Description
la Current measured on phase la
lb Current measured on phase lb
lc Current measured on phase lc
ln Measured ground-fault current
l(unbal) Calculated phase unbalance
TH LEVEL Calculated thermal level
I1_min One-minute demand value
In_min Demand value during the specified time range
Max I Maximum one-minute demand value during
the specified time range

4.1.3. Configuration
Fig. 4.1.3.-1 illustrates how the internal and digital input signals can be configured
to obtain the required protection functionality.

16

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535

Downloaded from www.Manualslib.com manuals search engine

D15 D14 D13 D12 D11 IRF SO2 SO1 PO3 PO2 PO1 SO5 SO4 SO3

Fig. 4.1.3.-1
X3.1 6 5 4 3 2 1 X4.1 21 22 23 24 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 16 17 18 19 20 21 22 23 24 X3.1

Self-supervision IRF
Optional Warning

SGB5 SGB4 SGB3 SGB2 SGB1

51P Pickup 1 1 1 1 1 1 1 1
11 11 11 11 11 Blocking Trip 2 2 2 2 2 2 2 2

50P-1 Pickup 3 3 3 3 3 3 3 3
12 12 12 12 12 Blocking Trip 4 4 4 4 4 4 4 4
Ia
Feeder Protection Relay

Ib 50P-2 Pickup

Signal diagram
5 5 5 5 5 5 5 5
Icı ı Trip 6 6 6 6 6 6 6 6

51N Pickup 7 7 7 7 7 7 7 7
Blocking Trip 8 8 8 8 8 8 8 8
13 13 13 13 13

In 50N Pickup 9 9 9 9 9 9 9 9
14 14 14 14 14 Blocking Trip 10 10 10 10 10 10 10 10

46 Pickup 11 11 11 11 11 11 11 11
Blocking Trip 12 12 12 12 12 12 12 12
15 15 15 15 15
Technical Reference Manual - ANSI Version

49 Pickup 13 13 13 13 13 13 13 13
X5.1 Trip Trip 14 14 14 14 14 14 14 14
Light Sensor 1 Arc 51P/51N Arc light output
Light Sensor 2 23 23 23 23 23 23 23 23
9 9 9 9 9 External Arc Trip 22 22 22 22 22 22 22 22
X5.2
Optional
79 Arc light output

18 18 18 18 18 16 16 16 16 16 16 16 16
CB Position Open Open CB Command
19 19 19 19 19 17 17 17 17 17 17 17 17
CB Position Closed Close CB Command
16 16 16 16 16 19 19 19 19 19 19 19 19
AR Disable CB Reclosing Failed
17 17 17 17 17 20 20 20 20 20 20 20 20
CB Close Disable Shot Due
20 20 20 20 20 18 18 18 18 18 18 18 18
External AR Initiation Definite Trip Alarm
21 21 21 21 21 21 21 21
AR Lockout
Trip Lockout

8 8 8 8 8
External Triggering
10 10 10 10 10
Reset Trip Lockout
6 6 6 6 6 15 15 15 15 15 15 15 15
External Trip External Trip

CBFAIL
7 7 7 7 7
External Triggering Trip
1 1 1 1 1
2 2 2 2 2 Indications Cleared
3 3 3 3 3 Output contacts unlatched

4 4 4 4 4 Memorized values cleared

Setting group selection
5 5 5 5 5
Time sync

SGF1 ...SGF5
SFL1 ...SGL8

SignDiagrREF610_a
REF 610

17
 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

The functions of the relay are selected with the switches of switchgroups SGF, SGB,
SGR and SGL. The checksums of the switchgroups are found under SETTINGS in
the HMI menu. The functions of the switches are explained in detail in the
corresponding SG_ tables.

4.1.4. Protection

4.1.4.1. Block diagram

Switchgroups for Switchgroups for

digital inputs Protection relay functions programmable LEDs
SGB1...5
SGB1...5 51P 51N SGL1...8
SGL1...8
51P Trip
Reset 1 1) 50P-1 Trip
Reset 2 2) 50P-2 Trip
Reset 3 3) Pickup Pickup
51N Trip
Setting group Block Trip Block Trip
50N Trip
Time sync
DI1 50P-1 50N 46 Trip
Digital inputs Ext Trip LED1
DI2 Ex Trig CBFAIL 49 Alarm
49 Trip LED2
Optional digital DI3 Ext Trig Trip lockout LED3
DI4 Ext Arc Double Pickup Double Pickup Trip Lockout
inputs LED4 Programmable
DI5 Trip lockout reset Block Trip Block Trip Definate Trip Alarm
(I/O module) LED5 LEDs
Block 51P Shot Due
50P-2 46 AR Lockout LED6
Block 50P-1
CB Pos Open LED7
Block 51N
Block 50N CB Pos CLosed LED8
Block 46 Pickup Pickup DI1
AR Disable Trip Block Trip DI2
CB Close Disable I DI3
49
CB Pos Open DI4
CB Pos Close DI5
Ext AR Initiation Ia ı
Arc Trip
Ib Pickup Pickup Arc light output
Ic Trip Block Trip
In CBFAIL
Switchgroups for
output contacts
Ia
PO1 SGR1...5
Ib PO2 51P Pickup
In EXT TRIG
Ic 51P Trip
Analogue inputs Trip lockout Arc 50, Arc 50N 50P-1 Pickup
50P-1 Trip
Ext Trig Light1 50P-2 Pickup
In Light2 Light Output 50P-2 Trip
Reset
Trip lockout Ext Arc Trip 51N Pickup
PO3
51N Trip PO1
79, AR
Autoreclose 50N Pickup PO2 Digital outputs
PO3 (Output contacts)
CB Pos Open Open CB Cmd 50N Trip
Optional arc detector inputs Light sensor input1 SO1
CB Pos Closed Close CB Cmd
(Communication module)ı Light sensor input 2 46 Pickup SO2
AR Disable CB Reclose Failed 6 Trip SO3 Optional digital
CB Close Disable Shot DUe outputs
49 Alarm SO4
Ext AR Initiation Definite Trip Alarm (I/O module)
49 Trip SO5
51P Pickup AR Lockout Ext Trip
51P Trip Block 51P Open CB Cmd
50P-1 Trip Block 50P-1 Close CB Cmd
50P-2 Trip Block 50P-2 Definate Trip Alarm
51N Pickup Block 51N CB Reclose Failed
51N Trip Block 50N Shot Due
50N Pickup
AR Lockout
46 Trip
Arc Trip
49 Alarm
Arc light output
49 Trip
Arc Trip Trip lockout
CBFAIL Warning
IRF
ı SGF1...SGF5
ˇ ı
ııııı ˇ
Disturbance
Disturbance recorder
recorder IRF INDICATION IRF indication LED (green)
(4
(4 analogue
analogue ++ upup to
to 88 digital
digital channels)
channels) START/ALARM INDICATION Start/Alarm (yellow) and
TRIP INDICATION trip (red) indication LEDs
Ia DI1 51P Pickup
Ib DI2 51P Trip
Ic DI3 50P-1 Pickup
In DI4 50P-1 Trip
DI5 50P-2 Pickup
50P-2 Trip
51N Pickup
The dashed line indicates optional functionality. 51N Trip
50N Pickup
1) Clear indications by the digital input signal 50N Trip
2) Clear indications and unlatch output contacts by the 46 Pickup
digital input signal 46 Trip
3) Reset indications and memorized values; unlatch output 49 Pickup
contacts by the digital input signal 49 Trip
BlockDiagrREF610_a

Fig. 4.1.4.1.-1 Block diagram

18

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

4.1.4.2. Overcurrent protection

The non-directional overcurrent protection detects overcurrent caused by phase-to-
phase and phase-to-ground short circuits.
When one or several phase currents exceed the set pickup value of the low-set
element, 51P, the element will generate a pickup signal after a ~ 55 ms. When the
set operate time at definite-time characteristic or the calculated operate time at
IDMT (mode) characteristic elapses, the element will generate a trip signal. Element
51P has a settable resetting time (both at definite-time and IDMT (mode)
characteristics), RSET, for reset coordination with existing electromechanical relays
or for reducing fault clearance times of recurring, transient faults. If element 51P has
picked up and the phase currents fall below the set pickup value of the element, the
pickup of the element will remain active for the set resetting time. If the phase
currents exceed the set pickup value again, while the timer is being reset, the pickup
of the element will remain active. Consequently, the set resetting time ensures that
when the element picks up because of current spikes, it will not be immediately
reset. However, if element 51P has already tripped, the element will be reset in 50
ms after all three phase currents have fallen below 0.5 times the set pickup value of
the element.
The inverse-time function of element 51P can be set to be disabled when element
50P-1 and/or 50P-2 picks up. In this case, the operate time will be determined by
element 50P-1 and/or 50P-2. The selection is made in SGF4. It is possible to block
the tripping of the low-set overcurrent element by applying a digital input signal to
the relay.
When one or several phase currents exceed the set pickup value of the high-set
element, 50P-1, the element will generate a pickup signal after a ~ 30 ms’ pickup
time. When the set operate time at definite-time characteristic elapses, the element
will generate a trip signal. Element 50P-1 can be given an instantaneous
characteristic by setting the operate time to the minimum, i.e. 0.04 s.The set pickup
value of element 50P-1 can be set to be automatically doubled in a pickup situation,
i.e. when the object to be protected is being connected to a network. Consequently,
a set pickup value below the connection inrush current level can be selected for
element 50P-1. A pickup situation is defined as a situation where the maximum
phase current rises from a value below 0.12 x 51P to a value above 1.5 x 51P within
less than 60 ms. The pickup situation ends when all phase currents fall below 1.25 x
51P and remain below for at least 200 ms. The selection is made in SGF4.
It is possible to block the tripping of the high-set overcurrent element by applying a
digital input signal to the relay.
Element 50P-1 can be set out of operation in SGF3. This state will be indicated by
dashes on the LCD and by “999” when the set pickup value is read via serial
communication.
When one or several phase currents exceed the set pickup value of the instantaneous
element, 50P-2, the element will generate a pickup signal after a ~ 30 ms’ pickup
time. When the set operate time at definite-time characteristic elapses, the element
will generate a trip signal. Element 50P-2 can be given an instantaneous
characteristic by setting the operate time to the minimum, i.e. 0.04 s.

19

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

Element 50P-2 can be set out of operation in SGF3. This state will be indicated by
dashes on the LCD and by “999” when the set pickup value is read via serial
communication. Elements 50P-1 and 50P-2 will be reset in 50 ms after all three
phase currents have fallen below the set pickup value of the element.
Note!
Elements 51P and 50P-1 can be set to be blocked by the auto-reclose function.

4.1.4.3. Ground-fault protection

The non-directional ground-fault current protection detects phase-to-ground
currents, caused by insulation failure due to ageing and thermal cycling, for instance.
When the ground-fault current exceeds the set pickup value of the low-set element,
51N, the element will generate a pickup signal after a ~ 60 ms’ pickup time. When
the set operate time at definite-time characteristic or the calculated operate time at
IDMT (mode) characteristic elapses, the element will generate a trip signal. The
low-set element can be given an instantaneous characteristic by setting the operate
time to the minimum, i.e. 0.05 s.
Element 51N has a settable resetting time (both at definite-time and IDMT (mode)
characteristics),RSET, for reset coordination with existing electromechanical relays
or for reducing fault clearance times of recurring, transient faults. If element 51N has
picked up and the ground-fault current falls below the set pickup value of the
element, the pickup of the element will remain active for the set resetting time. If the
ground-fault current exceeds the set pickup value again, while the timer is being
reset, the pickup of the element will remain active. Consequently, the set resetting
time ensures that when the element picks up because of current spikes, it will not be
immediately reset. However, if element 51N has already tripped, the element will be
reset in 50 ms after the ground-fault current has fallen below 0.5 times the set pickup
value of the element.
The inverse-time function of element 51N can be set to be disabled when element
50N picks up. In this case, the operate time will be determined by element 50N. The
selection is made in SGF4.
When the ground-fault current exceeds the set pickup value of the high-set element,
50N, the element will generate a pickup signal after a ~ 40 ms’ pickup time. When
the set operate time at definite-time characteristic elapses, the element will generate
a trip signal. The high-set element can be given an instantaneous characteristic by
setting the operate time to the minimum, i.e. 0.05 s. The element will be reset in 50
ms after the ground-fault current has fallen below the set pickup value of the
element.
The set pickup value of element 50N can be set to be automatically doubled in a
pickup situation, i.e. when the object to be protected is being connected to a network.
Consequently, a set pickup value below the connection inrush current level can be
selected for the element. A pickup situation is defined as a situation where the
ground-fault current rises from a value below 0.12 x 51N to a value above 1.5 x 51N
within less than 60 ms. The pickup situation ends when the current falls below 1.25
x 51N and remain below for at least 200 ms. The selection is made in SGF4.
Element 50N can be set out of operation in SGF3. This state will be indicated by
dashes on the LCD and by “999” when the set pickup value is read via serial
communication.

20

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

It is possible to block the tripping of an ground-fault element by applying a digital

input signal to the relay.
Note!
Elements 51N and 50N can be set to be blocked by the auto-reclose function.

4.1.4.4. Thermal protection for cables

The thermal protection detects long-time overloads during normal operation.
Prolonged overloading results in the thermal stress capacity of the cable being
exceeded, which degrades the insulation of the cable, which in turn may cause a
short circuit or an ground fault. The heating up of the cable follows an exponential
curve, the levelled-out value of which is determined by the squared value of the load
current. The thermal protection may equally well be used to protect dry-type
transformers, capacitor banks, busbars and overhead lines, for instance.
The thermal protection element continuously calculates the thermal capacity used as
a percentage of the cable’s total thermal capacity. The thermal capacity is calculated
as follows:

2 –t ⁄ τ
θ = ⎛ -------------------------⎞ × ( 1 – e
I
) × 100%
⎝ 1.05 × FLA⎠
where

θ1) = thermal capacity

I = phase current value
FLA = set full load current
t = time (in minutes)
τ = time constant (in minutes)
1)
θ equals TH LEVEL

“When one or several phase currents exceed the set full load current, FLA, element
49 will pickup. At the same time, the thermal capacity will start to increase at a rate
depending on the current amplitude and the prior load of the cable.
When the thermal capacity, influenced by the thermal history of the cable, exceeds
the set alarm level, 49ALARM the element will generate an alarm signal. The
thermal alarm can be used to avoid unnecessary tripping due to a beginning
overload. The thermal level at various constant currents are presented in the table
below:

Table 4.1.4.4-1 Thermal level at constant currents

I/FLA Thermal level (%)
1.0 90.7
0.9 73.5
0.8 58
0.7 44.4

21

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

Table 4.1.4.4-1 Thermal level at constant currents

I/FLA Thermal level (%)
0.5 22.7
0.3 8.2
0 0
When the thermal capacity exceeds the trip level, the element will generate a trip
signal. The operate time, i.e. the time from when the element picks up until it trips,
is determined by the time constant, τ, and depends on the cable (cable cross section
area and cable rated voltage). The time constant is provided by the cable
manufacturer. For a 22 kV cable, the typical time constant is 20 minutes. For operate
times, see Fig. 4.1.4.4.-1...Fig. 4.1.4.4.-3.

⎧
⎪
t = τ x ln ⎨
( ) I
FLA
2
− ( ) ⎫⎪⎬
I p
FLA
2

⎪⎩ ( )
FLA
I 2
− 1 . 1025 ⎪⎭
The operate time is calculated as follows:
where
FLA = set full load current
Ip = prior load current
t = time (in minutes)
τ = time constant (in minutes)
ln = natural logarithm
At power up, the thermal level will be set to 75 percent of the thermal capacity of
the cable. This will ensure that the element will trip within a safe time span in case
of an overload. The calculated thermal level will approach the thermal level of the
cable.
Element 49 can be set out of operation in SGF3. This state will be indicated by
dashes on the LCD and by “999” when the set full load current is read via serial
communication.
Note!
At an alarm level below 75 percent, connecting the auxiliary supply to the relay will
cause a thermal alarm due to the initialization of the thermal level to 75 percent of
the thermal capacity of the cable. The thermal level can be reset via the HMI during
power up.
Note!
The thermal level can be reset or changed via serial communication, which will
generate an event code.

22

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

t/s

100000

10000

1000

t[min]

100
90
60
40
25
10 15
10

1
1

1.05
PrLoad0_a

0
1 10 I/I q
CURRENT IN MULTIPLES OF FULL LOAD CURRENT SETTING

Fig. 4.1.4.4.-1 Trip curves when no prior load

23

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

t/s

100000

10000

1000

t[min]

100

90
60
40
10 25
15
10

5
1

1
PrLoad0.7_a

1.05
0
1 10 I/Iq
CURRENT IN MULTIPLES OF FULL LOAD CURRENT SETTING

Fig. 4.1.4.4.-2 Trip curves at prior load 0.7 x FLA

24

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

t/s

100000

10000

1000

t[min]

100

10

90
60
40
25
1
15
10

5
1
1.05
PrLoad1_a

0
1 10 I/Iq
CURRENT IN MULTIPLES OF FULL LOAD CURRENT SETTING

Fig. 4.1.4.4.-3 Trip curves at prior load 1 x FLA

25

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

4.1.4.5. Phase discontinuity protection

The phase discontinuity protection detects phase unbalance between phases Ia, Ib
and Ic, caused by a broken conductor, for instance. The difference between the
minimum and maximum phase currents is calculated as follows:

I max − I min
I ( unbal ) = x 100%
I max
When the current difference exceeds the set pickup value of the phase discontinuity
element, 46, the element will generate a pickup signal after a ~ 100 ms. When the
set operate time at definite-time characteristic elapses, the element will generate a
trip signal. The element will be reset in 70 ms after the current difference has fallen
below the set pickup value of the element.
The phase discontinuity protection will be disabled when all phase currents fall
below 0.1 x CT.
It is possible to block the tripping of the phase discontinuity element by applying a
digital input signal to the relay.
Element 46 can be set out of operation in SGF3. This state will be indicated by
dashes on the LCD and by “999” when the set pickup value is read via serial
communication.

4.1.4.6. Circuit-breaker failure protection

The circuit-breaker failure protection (CBFAIL) detects situations where the trip
remains active although the circuit breaker should have operated.
If a trip signal generated via output PO1 is still active and the current has not been
cut off on expiration of the CBFAIL set operate time, the CBFAIL will generate a
trip signal via output PO2.
Note!
The CBFAIL will not be triggered in case of a thermal alarm, thermal or external
trip.
The CBFAIL can also be selected to be triggered by applying a digital input signal
to the relay. In this case, the CBFAIL will generate a trip signal via output PO2 if
the current has not been cut off on expiration of the set operate time.
Internal triggering is selected by activating the CBFAIL in SGF and external
triggering by activating the CBFAIL in SGB. Both triggering options can be selected
at the same time.
Normally, the CBFAIL controls the upstream circuit breaker. However, it can also
be used for tripping via redundant trip circuits of the same circuit breaker.

26

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

4.1.4.7. Arc protection

The arc protection detects arc situations in air insulated metal-clad switchgears,
caused by human error during maintenance or poor contact in the cable connections,
for instance. Local light detection requires the optional arc light detection hardware.
The arc protection can be realized as a stand-alone function in a single REF 610 or
as a station-wide arc protection including several REF 610 protection relays. If
realized as a station-wide arc protection, different tripping schemes can be selected
for the operation of the circuit breakers of the incoming and outgoing feeders.
Consequently, the REF 610 relays in the station can, for instance, be set to trip the
circuit breaker of either the incoming or the outgoing feeder depending on the fault
location in the switchgear. For maximum safety, the REF 610 relays can be set to
always trip both the circuit breaker of the incoming feeder and that of the outgoing
feeder.
The arc protection consists of:
• optional arc light detection hardware with automatic backlight compensation for
two lens sensors
• a non-trip light signal output for routing the locally detected light signal to
another relay
• the protection element ARC with phase- and ground-fault current measurement.
The light from an arc is detected either locally or via a remote light signal. Locally,
the light is detected by lens sensors connected to inputs Light sensor 1 and Light
sensor 2 on the serial communication module of the relay. The lens sensors can be
placed, for instance, in the busbar compartment and the cable compartment of the
metal-clad cubicle.
The light detected by the lens sensors is compared to an automatically adjusted
reference level. Inputs Light sensor 1 and Light sensor 2 have their own reference
levels. When the reference level of either or both inputs is exceeded, an arc has been
detected locally.
When light has been detected locally or remotely and one or several phase currents
exceed the set current limit Arc50P, or the ground-fault current the set current limit
Arc50N, the arc protection element (ARC) will generate a trip signal in less than 15
ms. The element will be reset in 30 ms after all three phase currents and the ground-
fault current have fallen below the set current limits.
The non-trip light signal output, L>, can be configured to be activated either
immediately upon detection of light in all situations, or only when the arc has not
been extinguished by the time the trip signal is generated. The selection is made in
SGF4. By routing the light signal output to an output contact connected to a digital
input of another REF 610 non-trip relay, a station-wide arc protection is realized.
Element ARC and the non-trip light signal output can be set out of operation in
SGF3.
Note!
Inputs not in use should be covered with dust caps.
Note!

27

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

The warning signal generated in case of continuous light on the light sensor inputs
can be routed to SO2 by setting switch SGF1/8 to 1.

Arc50P (setting)

Ip (max. measured phase

current)
SGF3/6

0
Arc Trip
25ms
Arc50N (setting)

I0 (measured)

Remote Light Signal (binary

input)

Light reference level SGB1..5/9

(automatically adjusted)

Light sensor 1 Light Signal Output

SGF4/6
SGF3/7

Light reference level

(automatically adjusted)

Light sensor 2

Fig. 4.1.4.7.-1 Block diagram of the arc protection

4.1.4.8. Auto-reclose function

The vast majority of MV overhead line faults are transient and automatically cleared
by momentarily de-energizing the line. De-energizing of the fault location for a
selected time period is implemented through automatic reclosing, during which
most faults can be cleared.
At a permanent fault, auto-reclosing is followed by definite tripping. A permanent
fault must be located and cleared before the fault location can be re-energized.
The auto-reclose (AR) function of REF 610 can be used with any circuit breaker
suitable for auto-reclosing. The AR function provides three programmable
auto-reclose shots and can thus be set to perform one to three successive
auto-reclosures of desired type and duration, one high-speed and one delayed, for
instance.
The AR function can be initiated by pickup and trip signals from certain overcurrent
and ground-fault protection elements. Consequently, tripping of the arc protection
element, for instance, does not initiate the AR function. Initiation is also possible
from an external device via a digital input.
The AR function can be disabled (AR Disable) by trip signals from certain
protection elements or via a digital input. Disable is advantageous with tripping
faults as this type of fault cannot be cleared during an auto-reclose sequence.
Tripping faults are detected by the CBFAIL, for instance. Disable will also interrupt
any ongoing shot.

28

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

The initiation of one or several auto-reclose shots can be set to be blocked by trip
signals from certain protection elements. Blocking is also possible via a digital
input. Blocking can be used to limit the number of shots in an auto-reclose sequence,
which may be advantageous with certain types of faults. In case of shot initiation
while a blocking is active, the next shot will be initiated.
The AR function monitors the position and status of the circuit breaker. Information
on the circuit-breaker position is always required whereas circuit-breaker status is
optional. For safety reasons, shot initiation is not possible when the circuit breaker
is open. If the circuit breaker is not ready, due to an discharged spring, for instance,
reclosing can be disabled via a digital input (CB Close Disable). Disable of
reclosing is checked only when necessary and can therefore not be used to prevent
initiation or progression of a shot.
For co-ordination of the other protection devices in the network, such as
down-stream fuses, the AR function supports optional blocking of selectable
overcurrent and ground-fault protection elements (refer to section Blocking of
protection elements). By setting a element with a short operate time to trip and
initiate only the first auto-reclose shot, fast tripping and shot initiation will be
achieved. After this, the element will be blocked to allow selective delayed tripping
of another element in accordance with the time-grading plan of the system.
The typical auto-reclose sequence is as follows: the overcurrent or ground-fault
protection detects a network fault, trips the circuit breaker and initiates the first
auto-reclose shot. At the time of shot initiation, the set open time for shot 1 will
pickup. When the set open time elapses, the blocking of selected protection elements
will be activated and the AR function will issue a reclosing command (Close CB
Command) to the circuit breaker, the duration of which is settable. In addition, the
set reset time and set cutout time will pickup when the set open time elapses. The
blocking of protection elements will be reset on expiration of the cutout time. For
the cutout time, refer to section Fast tripping and initiation of shot 1 using two
protection elements.
If the network fault is cleared, i.e. the auto-reclosure is successful, the set reset time
will expire and the AR function will be automatically reset to the quiescent
condition.
However, if the network fault is not cleared, i.e. the auto-reclosure is unsuccessful,
and the protection trips the circuit breaker before expiration of the set reset time, the
next shot will be initiated (provided that a further auto-reclosure is allowed). At the
time of shot initiation, the set open time for shot 2 will pickup. When the set open
time elapses, the blocking of selected protection elements (may differ from shot 1)
will be activated and the AR function will issue a reclosing command to the circuit
breaker. In addition, the set reset time and set cutout time will pickup when the set
open time elapses. The blocking of protection elements will be reset on expiration
of the set cutout time.
If the network fault is cleared, the AR function will be automatically reset after the
reset time. However, if the fault is not cleared and the protection trips the circuit
breaker before expiration of the reset time, the next shot will be initiated (provided
that a further auto-reclosure is allowed). At the time of shot initiation, the set open
time for shot 3 will pickup. When the set open time elapses, the blocking of selected
protection elements (the same as for shot 2) will be activated and the AR function

29

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

will issue a reclosing command to the circuit breaker. In addition, the set reset time
and set cutout time will pickup when the set open time elapses. The blocking of
protection elements will be reset on expiration of the set cutout time.
If the network fault has still not been cleared, i.e. all selected auto-reclose shots have
been unsuccessful, and the protection trips the circuit breaker before expiration of
the set reset time, the AR function will generate a definite trip alarm. The circuit
breaker will now remain open and the AR function will be locked out.
As default, the AR function is not in use (number of auto-reclose shots = 0). The AR
function can be activated either via the HMI or with SPA parameter S25 by setting
the number of auto-reclose shots to 1, 2 or 3.

Shot Due
S

Shot 1 t 0
Shot Initiation
Shot 2 t 0
t
Shot 3 0

CB Close Diasable

Close CB Command
S

CB Closed
R
CB Closing Time
t
0

CB Reclosing Failed

Fig. 4.1.4.8.-1 Simplified shot logic diagram

Shot initiation
The AR function can be initiated by any of the following signals:
• external AR initiation signal
• pickup signal from elements 51P and 51N
• trip signal from elements 51P, 50P-1, 51N and 50N
The pickup signal from elements 51P and 51N will initiate a shot on expiration of a
settable pickup delay for the respective element. At the factory default delay of 300
s, the pickup signal will, in practise, not be used for shot initiation. External AR
initiation by the digital input signal is selected in SGB.
Note!
Shot initiation by a pickup signal applies only to shot 1 and definite tripping.
Note!

30

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

The AR function will issue an opening command to the circuit breaker at shot
initiation by a pickup or a trip signal.

CB Closed
0
100ms

Shot Due

Shot Initiation

50P-1 Trip

External AR Initiation
Open CB Command
51P Trip

51P Pickup 51P pickup delay

t
0

50N Trip

51N Trip
51N pickup delay
51N Pickup t
0

Blocking of shot
SG1/
1..8

Fig. 4.1.4.8.-2 Simplified shot initiation logic diagram

Blocking of shot initiation
The initiation of one or several auto-reclose shots can be set to be blocked by any of
the following signals:
• external AR initiation signal
• trip signal from overcurrent elements 51P and 50P-1
• trip signal from ground-fault elements 51N and 50N
The selection is made in SG1 (see table 4.1.4.10-10).
Blocking of shot initiation can also be used to skip the entire shot sequence (by
blocking the initiation of all three shots), and go directly to definite tripping. Further,
it can be used, for instance, to allow shot initiation by the trip signal from element
51P, but to go directly to definite tripping in case of shot initiation by the trip signal
from element 50P-1.
Note!
Activation of any above-mentioned signal will always cause the AR function to
issue an opening command to the circuit breaker. If the signal used for blocking is
not simultaneously used for initiation of the next shot, the AR function will generate
a definite trip alarm and be locked out.
Note!
Shot initiation is blocked only for as long as the blocking signal is active.

31

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

Note!
In case of shot initiation while a blocking is active, the next shot (if such has been
selected and not blocked) will be initiated. This can be used to skip Shot 1, for
instance.
Disable of the auto-reclose function
The AR function can be disabled (AR Disable) by any of the following signals:
• external AR disable signal
• trip signal from the arc protection element, ARC
• trip signal from the thermal protection element, 49
• trip signal from the CBFAIL
• alarm signal from the thermal protection element, 49
• trip signal from overcurrent element 50P-2
• trip signal from ground-fault element 50N
• trip signal from the phase discontinuity element, 46
The trip signals from elements ARC and 49 and from the CBFAIL are fixed and will
thus always disable the AR function. External AR disable by the digital input signal
is selected in SGB, and the alarm signal from element 49 and the trip signals from
elements 50P-2, 50N and 46 in SG3 (see table 4.1.4.10-12).
Note!
The AR function will remain disabled after all disable signals have been reset for a
time equal in length to the set reset time.
Note!
Disable will always also interrupt any ongoing shot.
Information on the circuit-breaker position
The AR function requires information on the circuit-breaker position. Any digital
input can be selected for the information on the circuit breaker being open (CB
Position Open) and closed (CB Position Closed) in SGB. Normally, two
digital inputs is recommended although either one is enough for the AR function.
Information on the circuit-breaker position is used in the following situations:
• At manual circuit-breaker closing, the AR function will be disabled for the reset
time.
• At manual circuit-breaker closing during an ongoing shot, the shot will be
interrupted and the AR function disabled during the reset time.
• Shot initiation is allowed only when the circuit breaker is closed.
• Reclosing of the circuit breaker is ended immediately after the AR function has
received information that the circuit breaker has been closed.
Circuit-breaker closing
When the set open time elapses, the AR function will issue a reclosing command to
the circuit breaker (Close CB Command). Reclosing can be disabled via a digital
input (CB Close Disable). External disable of reclosing by the digital input
signal is selected in SGB.

32

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

When reclosing is disabled, or the circuit breaker does not close before expiration of
the set CB closing time, the circuit breaker will remain open and the AR function
will generate a CB Reclosing Failed signal.
Reclosing is disabled and the CB Reclosing Failed signal generated also if
an AR initiation signal is active, i.e. the fault has not been cleared, when reclosing
begins.
The duration of the reclosing command is settable (CB closing time). However,
reclosing of the circuit breaker will end immediately after the AR function has
received information that the circuit breaker has been closed, or if a protection trips
the circuit breaker again.
Blocking of protection elements
In several applications, such as fuse-saving (refer to section Fast tripping and
initiation of shot 1 using two protection elements), the aim is at fast tripping and
initiation of shot 1 and delayed tripping and initiation of shot 2 and 3. Consequently,
if two protection elements are used, one fast and the other one delayed, the fast
element should be set to be blocked by the AR function during shot 2 and 3.
The protection elements can be set to be blocked at shot 1 and/or shot 2 and 3. The
selection is made in SG2 (see table 4.1.4.10-11).
Definite trip alarm
The AR function will generate a definite trip alarm signal after an unsuccessful
auto-reclose sequence, i.e. when no more auto-reclose shots are allowed but the
network fault has not be cleared, the circuit breaker is open and there is no ongoing
shot. The definite trip alarm signal will also be generated in case a protection trips
the circuit breaker while the AR function is disabled.
Note!
The definite trip alarm signal is active for 1 second.
Note!
The definite trip alarm signal will not be generated if the AR function has been set
out of operation.
Lockout of the auto-reclose function
The lockout signal indicates whether the AR function is ready for shot initiation. The
AR function will be locked out in any of the following situations:
• the AR function generates a definite trip alarm
• the AR function is disabled
• circuit-breaker closing fails
• manual circuit-breaker closing is detected
The lockout signal will be reset and the AR function ready for shot initiation on
expiration of the set reset time. The set reset time will pickup when the definite trip
alarm signal, the AR disable signal or the CB reclosing failed signal has
been reset or the circuit breaker closed, depending on the reason for the AR function
being locked.

33

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

4.1.4.9. Inverse definite minimum time characteristics

The low-set overcurrent and ground-fault elements can be given an inverse definite
minimum time (IDMT (mode)) characteristic. At IDMT (mode) characteristic, the
operate time of the element is dependent on the current value: the higher the current
value, the shorter the operate time.
REF 610 provides eight IDMT (mode) characteristics, of which four comply with
the IEC 60255-3 and three with the IEEE C37.112 standard. One is a special
characteristic according to ABB praxis and is referred to as RI.
The time/current characteristics can be selected either via the HMI or the SPA bus
as follows:

Table 4.1.4.9-1 Time/current characteristic settings

Value Time/current characteristic
0 Definite time
1 IEC Extremely inverse
2 IEC Very inverse
3 IEC Normal inverse
4 IEC Long-time inverse
5 RI-type
6 IEEE Extremely inverse
7 IEEE Very inverse
8 IEEE Moderately inverse

IDMT (mode) characteristics according to IEC 60255-3

REF 610 provides four time/current curve groups which comply with the IEC
60255-3 standard: normal inverse, very inverse, extremely inverse and long-time
inverse. The relationship between time and current is expressed as follows:

⎛ β ⎞
t [ s ] = ⎜ ------------------ ⎟ × TD
⎝ Mα – 1 ⎠

where
t = operate time
TD = time multiplier
M = multiplies of pickup current

Note!
The actual operate time of the relay (see Fig. 4.1.4.9.-1...Fig. 4.1.4.9.-4), includes an
additional filter and detection time, and the operate time of the trip output contact.
When the operate time of the relay is calculated as above, approximately 30 ms
should be added to the result.

34

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

Table 4.1.4.9-2 Values of constants α and β

Time/current curve group α β
Normal inverse 0.02 0.14
Very inverse 1.0 13.5
Extremely inverse 2.0 80.0
Long-time inverse 1.0 120

According to the standard, the normal current range is 2...20 times the set pickup
value at normal inverse, very inverse or extremely inverse characteristic. The relay
is to pickup before the current exceeds the set pickup value by 1.3 times. At long-
time inverse characteristic, the normal current range is specified to be 2...7 times the
set pickup value, and the relay is to pickup before the current exceeds the set pickup
value by 1.1 times.

Table 4.1.4.9-3 Operate time tolerances specified by the standard 1)

M 2) Normal Very Extremely Long time
2 2,22E 2,34E 2,44E 2,34E
5 1,13E 1,26E 1,48E 1,26E
7 - - - 1,00E
10 1,01E 1,01E 1,02E -
20 1,00E 1,00E 1,00E -
1)
E = accuracy in percent; - = not specified
2)
Multiples or pickup current (a phase and ground)

Within the normal current range the inverse-time element fulfils the tolerance
requirements of class 5 at all degrees of inversity.
The time/current curve groups based on the IEC standard are illustrated in
Fig. 4.1.4.9.-1...Fig. 4.1.4.9.-4.
Note!
If the ratio between the current and the set pickup value is higher than 20, the operate
time will be the same as when the ratio is 20.

35

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

t/s
t/s
70
60
50
40

30

20

10
9
8
7
6
5
4

3 TD
k

1.0
2 0.9
0.8
0.7
0.6
0.5
1
0.9 0.4
0.8
0.7 0.3
0.6
0.5
0.2
0.4

0.3
0.1
0.2

0.05

0.1
0.09
0.08
0.07
0.06
0.05
0.04
IEC_NoInvREF610_a

0.03

0.02
1 2 3 4 5 6 7 8 910 20 I/I>
CURRENT IN MULTIPLES OF SETTING

Fig. 4.1.4.9.-1 Normal inverse-time characteristic

36

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

t/s
t/s
t/s
70
60
50
40

30

20

10
9
8
7
6
5
4

1
0.9 k
TD
0.8
0.7 1.0
0.9
0.6 0.8
0.5 0.7
0.6
0.4
0.5
0.3 0.4

0.3
0.2
0.2

0.1
0.09 0.1
0.08
0.07
0.06
0.05
0.05
0.04
IEC_VeInvREF610_a

0.03

0.02
1 2 3 4 5 6 7 8 9 10 20 I/I>
CURRENT IN MULTIPLES OF SETTING

Fig. 4.1.4.9.-2 Very inverse-time characteristic

37

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

t/s
t/s
70
60
50
40

30

20

10
9
8
7
6
5
4

1
0.9
0.8
0.7
0.6
0.5
0.4

0.3
TD
k

0.2 1.0
0.8

0.6

0.1
0.09 0.4
0.08
0.07 0.3
0.06
0.2
0.05
0.04
0.1
IEC_ExInvREF610_a

0.03 0.05

0.02
1 2 3 4 5 6 7 8 9 10 20 I/I>
CURRENT IN MULTIPLES OF SETTING

Fig. 4.1.4.9.-3 Extremely inverse-time characteristic

38

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

t/s
t/s
t/s
700
600
500
400

300

200

100
90
80
70
60
50
40

30

20

10
9
8 k
TD
7
1.0
6 0.9
5 0.8
0.7
4 0.6
0.5
3
0.4

2
0.3

0.2

1
0.9
0.8
0.7
0.1
0.6
0.5
0.4
IEC_LoInvREF610_a

0.05
0.3

0.2
1 2 3 4 5 6 7 8 910 20 I/I>
CURRENT IN MULTIPLES OF SETTING

Fig. 4.1.4.9.-4 Long-time inverse-time characteristic

39

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

IDMT (mode) characteristics according to the IEEE C37.112

REF 610 provides three time/current curve groups which comply with the IEEE
C37.112 standard: extremely inverse, very inverse and moderately inverse. The
relationship between time and current is expressed as follows:

⎛ ⎞
⎜ A
⎟x
t(s) =
⎜ p
+B
⎟ TD
⎝ ( M ) −1 ⎠
where
t = operate time (in seconds)
TD = time dial
M = multiplies of pickup current

Note!
The actual operate time of the relay (see Fig. 4.1.4.9.-5...Fig. 4.1.4.9.-7), includes an
additional filter and detection time, and the operate time of the trip output contact.
When the operate time of the relay is calculated as above, approximately 30 ms
should be added to the result.

Table 4.1.4.9-4 Values of constants A, B and P

Time/current curve group A B P
Extremely inverse 6.407 0.025 2.0
Very inverse 2.855 0.0712 2.0
Moderately inverse 0.0086 0.0185 0.02

The time/current curve groups based on the IEEE standard are illustrated in
Fig. 4.1.4.9.-5...Fig. 4.1.4.9.-7.

40

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

t/s
t/s
70
60
50
40

30

20

10
9
8
7
6
5
4

1
0.9
0.8 n
0.7
TD
0.6 15
0.5 12
0.4 10
8
0.3
6
5
0.2
4

0.1 2
0.09
0.08
0.07
0.06 1
0.05
0.04
ANSI_ExInvREF610_a

0.03

0.02
1 2 3 4 5 6 7 8 9 10 20 I/I>
CURRENT IN MULTIPLES OF SETTING

Fig. 4.1.4.9.-5 Extremely inverse-time characteristic

41

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

t/s
t/s
70
60
50
40

30

20

10
9
8
7
6
5
4

n
TD
15
1
0.9 12
0.8 10
0.7
0.6 8
0.5 6
0.4 5
4
0.3
3
0.2
2

0.1 1
0.09
0.08
0.07
0.06
0.05
0.04
ANSI_VeInvREF610_a

0.03

0.02
1 2 3 4 5 6 7 8 9 10 20 I/I>
CURRENT IN MULTIPLES OF SETTING

Fig. 4.1.4.9.-6 Very inverse-time characteristic

42

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

t/s
t/s
70
60
50
40

30

20

10
9
8
7
6
5
4
TD
n
3
15
2 12
10
8

1 6
0.9
0.8 5
0.7 4
0.6
0.5 3
0.4
2
0.3

0.2
1

0.1
0.09
0.08
0.07
0.06
0.05
0.04
ANSI_MoInvREF610_a

0.03

0.02
1 2 3 4 5 6 7 8 9 10 20 I/I>
CURRENT IN MULTIPLES OF SETTING

Fig. 4.1.4.9.-7 Moderately inverse-time characteristic

43

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

RI-type characteristic
The RI-type characteristic is a special characteristic which is principally used for
obtaining time grading with mechanical relays. The relationship between time and
current is expressed as follows:

TD
t(s) = 1
0 . 339 − 0 . 236 x
M
where
t = operate time (in seconds)
TD = time dial
M = multiples of pickup current

Note!
The actual operate time of the relay (see Fig. 4.1.4.9.-8), includes an additional filter
and detection time, and the operate time of the trip output contact. When the operate
time of the relay is calculated as above, approximately 30 ms should be added to the
result.
The RI-type characteristic is illustrated in Fig. 4.1.4.9.-8.

44

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

t/s
t/s
70
60
50
40

30

20

10
9
8
7
6
5
4 k
TD
3 1.0
0.9
0.8
0.7
2
0.6
0.5
0.4
1 0.3
0.9
0.8
0.7
0.6 0.2
0.5
0.4
0.1
0.3

0.2
0.05

0.1
0.09
0.08
0.07
0.06
0.05
0.04

0.03
RI_InvREF610_a

0.02
1 2 3 4 5 6 7 8 910 20 I/I>
CURRENT IN MULTIPLES OF SETTING

Fig. 4.1.4.9.-8 RI-type characteristic

45

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

4.1.4.10. Settings
There are two alternative setting groups available, setting groups 1 and 2. Either of
these setting groups can be used as the actual settings, one at a time. Both groups
have their related registers. By switching between the setting groups, a whole group
of settings can be changed at the same time. This can be done in any of the following
ways:
• via the HMI
• entering SPA parameter V150 via serial communication
• via a digital input
Note!
Switching between setting groups via a digital input has higher priority than via the
HMI or with V150.
The setting values can be altered via the HMI or with a PC provided with the Relay
Setting Tool.
Before the relay is connected to a system it must be assured that the relay has been
given the correct settings. If there is any doubt, the setting values should be read with
the relay trip circuits disconnected or tested with current injection; refer to section
Check lists for additional information.

Table 4.1.4.10-1 Setting values

Setting Description Setting range Default setting
51P/In (CT) Pickup value of element 51P(CT) 0.30...5.00 x In (CT) 0.30 x In (CT)
51P TDLY Operate time of element 51P 0.05...300 s 0.05 s
51P MODE Time/current characteristic for 0...8 0
element 51P
51P TD IEC Time multiplier 51P TD IEC 0.05...1.00 0.05
51P TD Time multiplier 51P TD ANSI 1.0...15.0 1.0
ANSI
51P RSET Resetting time of element 51P 0.05...2.50 s 0.05 s
50P-1/In (CT) Pickup value of element 50P-1 0.50...35.0 x In (CT) 0.50 x In (CT)
50P-1 TDLY Operate time of element 50P-1 0.04...300 s 0.04 s
50P-2/In (CT) Pickup value of element 50P-2 0.50...35.0 x In (CT) 0.50 x In (CT)
50P-2 TDLY Operate time of element 50P-2 0.04...30.0 s 0.04 s
51N/In (CT) Pickup value of element 51N 1.0...100% In (CT) 1.0% In (CT)
51N TDLY Operate time of element 51N 0.05...300 s 0.05 s
51N MODE Time/current characteristic for 0...8 0
element 51N
51N TD IEC Time multiplier 51N TD IEC 0.05...1.00 s 0.05 s
51N TD Time multiplier 51N TD ANSI 1.0…15.0 1.0
ANSI
51N RSET Resetting time of element 51N 0.05...2.50 0.05
50N/In (CT) Pickup value of element 50N 5.0...400% In (CT) 5.0% In (CT)
50N TDLY Operate time of element 50N 0.05...300 s 0.05 s
46 PICKUP Pickup value of element 46 Pickup 10...100% 100%
46 TDLY Operate time of element 46 Pickup 1...300 s 60 s
FLA Full load current 0.30...1.50 x In (CT) 0.30 x In (CT)

46

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

Table 4.1.4.10-1 Setting values

Setting Description Setting range Default setting
τ Time constant of element 49 1...200 min 1 min
49 Alarm Alarm level of element 49 50...100% 49 trip 95% 49 trip
CBFAIL Operate time of CBFAIL 0.10...60.0 s 0.10 s
79 Number of AR shots 0 = AR is not in use 0
1 = shot 1
2 = shot 1 and 2
3 = shot 1, 2 and 3
Arc50P Current limit Arc51P of element ARC 0.50...35.0 x In (CT) 2.50 x In (CT)
Arc50N Current limit Arc51N of element ARC 5.0...400% In (CT) 20.0% In (CT)

47

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

Switchgroups and parameter masks

The settings can be altered and the functions of the relay selected in the SG_ selector
switchgroups. The switchgroups are software based and thus not physical switches
to be found in the hardware of the relay.
A checksum is used for verifying that the switches have been properly set. The
figure below shows an example of manual checksum calculation.

Switch Position Weighting Value

number factor
1 1 x 1 = 1
2 0 x 2 = 0
3 1 x 4 = 4
4 0 x 8 = 0
5 1 x 16 = 16
6 0 x 32 = 0
7 1 x 64 = 64
8 0 x 128 = 0
9 1 x 256 = 256
10 0 x 512 = 0
11 1 x 1024 = 1024
12 0 x 2048 = 0
13 1 x 4096 = 4096
14 0 x 8192 = 0
15 1 x 16384 = 16384
16 0 x 32768 = 0
17 1 x 65536 = 65536
18 0 x 131072 = 0
19 1 x 262144 = 262144
20 0 x 524288 = 0
21 1 x 1048576 = 1048576
22 0 x 2097152 = 0
23 1 x 4194304 = 4194304

checksum SG_ ∑ = 5505024

Fig. 4.1.4.10.-1 An example of calculating the checksum of a SG_ selector

switchgroup
When the checksum, calculated according to the example above, equals the
checksum of the switchgroup, the switches in the switchgroup have been properly
set.
The factory default settings of the switches and the corresponding checksums are
presented in the tables below.

48

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

SGF1...SGF5
Switchgroups SGF1...SGF5 are used for configuring the desired function as follows:

Table 4.1.4.10-2 SGF1

Default
Switch Function
setting
SGF1/1 Selection of the latching feature for PO1 0
SGF1/2 Selection of the latching feature for PO2 0
SGF1/3 Selection of the latching feature for PO3 0
• When the switch is in position 0 and the measuring signal
which caused the trip falls below the set pickup value, the
output contact will return to its initial state.
• When the switch is in position 1, the output contact will remain
active although the measuring signal which caused the trip
falls below the set pickup value.
A latched output contact can be unlatched either via the HMI, a
digital input or the serial bus.
SGF1/4 Minimum pulse length for SO1 and SO2 and optional SO3, SO4 0
and SO5
• 0=80 ms
• 1=40 ms
SGF1/5 Minimum pulse length for PO1, PO2 and PO3 0
• 0=80 ms
• 1=40 ms
Note!
The latching feature being selected for PO1, PO2 and PO3 will
override this function.
SGF1/6 CBFAIL 0
• 0 = CBFAIL is not in use
• 1 = the signal to PO1 will pickup a timer which will generate a
delayed signal to PO2, provided that the fault is not cleared
before the CBFAIL operate time has elapsed.
SGF1/7 Trip lockout function 0
• 0 = the trip lockout function is not in use.
• 1 = the trip lockout function is in use. PO3 is dedicated to this
function.
SGF1/8 External fault warning 0
• When the switch is in position 1, the warning signal from the
trip-circuit supervision or generated in case of continuous light
on light sensor inputs is routed to SO2.
ΣSGF1 0

49

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

Table 4.1.4.10-3 SGF2

Default
Switch Function
setting
SGF2/1 Operation mode of the pickup target of element 51P 0
SGF2/2 Operation mode of the pickup target of element 50P-1 0
SGF2/3 Operation mode of the pickup target of element 50P-2 0
SGF2/4 Operation mode of the pickup target of element 51N 0
SGF2/5 Operation mode of the pickup target of element 50N 0
SGF2/6 Operation mode of the pickup target of element 46 0
SGF2/7 Operation mode of the alarm target of element 49 0
• 0 = the pickup target will automatically be cleared once the
fault has disappeared
• 1 = latching. The pickup target will remain active although the
fault has disappeared.
ΣSGF2 0

Table 4.1.4.10-4 SGF3

Default
Switch Function
setting
SGF3/1 Disable of element 50P-1 0
SGF3/2 Disable of element 50P-2 0
SGF3/3 Disable of element 50N 0
SGF3/4 Disable of element 46 1
SGF3/5 Disable of element 49 1
SGF3/6 Disable of element ARC 1
• When the switch is in position 1, the element is disabled.
SGF3/7 Disable of light signal output 1
• When the switch is in position 1, the output is disabled.
ΣSGF3 120

Table 4.1.4.10-5 SGF4

Default
Switch Function
setting
SGF4/1 Automatic doubling of the pickup value of element 50P-1 0
• When the switch is in position 1, the set pickup value of the
element will be automatically doubled at high inrush situations.
SGF4/2 Inverse-time operation of element 51P disabled by the pickup of 0
element 50P-1
SGF4/3 Inverse-time operation of element 51P disabled by the pickup of 0
element 50P-2
• When the switch is in position 1, inverse-time operation is
disabled.
SGF4/4 Automatic doubling of the pickup value of element 50N 0
• When the switch is in position 1, the set pickup value of the
element will be automatically doubled at high inrush situations.
SGF4/5 Inverse-time operation of element 51N disabled by the pickup 0
of element 50N
• When the switch is in position 1, inverse-time operation is
disabled.

50

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

Table 4.1.4.10-5 SGF4

Default
Switch Function
setting
SGF4/6 Operation mode of light signal output 0
• When the switch is in position 1, the light signal output will be
blocked by the trip signal from element ARC.
ΣSGF4 0

Table 4.1.4.10-6 SGF5

Default
Switch Function
setting
SGF5/1 Selection of the latching feature for programmable LED1 0
SGF5/2 Selection of the latching feature for programmable LED2 0
SGF5/3 Selection of the latching feature for programmable LED3 0
SGF5/4 Selection of the latching feature for programmable LED4 0
SGF5/5 Selection of the latching feature for programmable LED5 0
SGF5/6 Selection of the latching feature for programmable LED6 0
SGF5/7 Selection of the latching feature for programmable LED7 0
SGF5/8 Selection of the latching feature for programmable LED8 0
• When the switch is in position 0 and the signal routed to the
LED is reset, the programmable LED will be cleared.
• When the switch is in position 1, the programmable LED will
remain lit although the signal routed to the LED is reset.
A latched programmable LED can be cleared either via the
HMI, a digital input or the serial bus.
ΣSGF5 0

SGB1...SGB5
The DI1 signal is routed to the functions below with the switches of switchgroup
SGB1, the DI2 signal with those of SGB2, and so forth.

Table 4.1.4.10-7 SGB1...SGB5

Default
Switch Function
setting
SGB1...5/1 • 0 = targets are not cleared by the digital input signal 0
• 1 = targets are cleared by the digital input signal
SGB1...5/2 • 0 = targets are not cleared and latched output contacts are not 0
unlatched by the digital input signal
• 1 = targets are cleared and latched output contacts are
unlatched by the digital input signal
SGB1...5/3 • 0 = targets and memorized values are not cleared and latched 0
output contacts are not unlatched by the digital input signal
• 1 = targets and memorized values are cleared and latched
output contacts are unlatched by the digital input signal
SGB1...5/4 Switching between setting groups 1 and 2 using the digital input 0
• 0 = the setting group cannot be changed using the digital input
• 1 = the setting group is changed by using the digital input.
When the digital input is energized, setting group 2 will be
activated, if not, setting group 1 will be activated.
Note!
When SGB1...5/4 is set to 1, it is important that the switch has
the same setting in both setting groups.

51

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

Table 4.1.4.10-7 SGB1...SGB5

Default
Switch Function
setting
SGB1...5/5 Time synchronization by the digital input signal 0
SGB1...5/6 External tripping by the digital input signal 0
SGB1...5/7 External triggering of the CBFAIL by the digital input signal 0
SGB1...5/8 External triggering of the trip lockout by the digital input signal 0
SGB1...5/9 External arc signalling by the digital input signal 0
SGB1...5/10 Resetting of the trip lockout by the digital input signal 0
SGB1...5/11 Blocking of tripping of element 51P by the digital input signal 0
SGB1...5/12 Blocking of tripping of element 50P-1 by the digital input signal 0
SGB1...5/13 Blocking of tripping of element 51N by the digital input signal 0
SGB1...5/14 Blocking of tripping of element 50N by the digital input signal 0
SGB1...5/15 Blocking of tripping of element 46 by the digital input signal 0
SGB1...5/16 External AR disable by the digital input signal 0
SGB1...5/17 External disable of CB reclosing by the digital input signal 0
SGB1...5/18 CB position open 0
SGB1...5/19 CB position closed 0
SGB1...5/20 External AR initiation by the digital input signal 0
ΣSGB1...5 0

SGR1...SGR8
The pickup, trip and alarm signals from the protection elements, the signals from the
auto-reclose function, and the external trip signal are routed to the output contacts
with the switches of switchgroups SGR1...SGR8. The signals are routed to
PO1...PO3 with the switches of switchgroup SGR1...SGR3 and to SO1...SO5 with
those of SGR4...SGR8.
The matrix below can be of help when making the desired selections. The pickup,
trip and alarm signals from the protection elements, the signals from the auto-reclose
function and the external trip signal are combined with the output contacts by
encircling the desired intersection point. Each intersection point is marked with a
switch number, and the corresponding weighting factor of the switch is shown to the
right in the matrix. The switchgroup checksum is obtained by vertically adding the
weighting factors of all the selected switches of the switchgroup.
Note!
The trip lockout signal is always routed to PO3.
Note!
The trip signal from CBFAIL is always routed to PO2.
Note!
The external fault warning is always routed to SO2.

52

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

PS_I/O card Optional I/O card

Weighting
PO1 PO2 PO3 SO1 SO2 SO3 SO4 SO5 factor
SGR1...8/1 51P 1 1 1 1 1 1 1 1 1

SGR1...8/2 51P TDLY 2 2 2 2 2 2 2 2 2

SGR1...8/3 50P-1 3 3 3 3 3 3 3 3 4

SGR1...8/4 50P-1 TDLY 4 4 4 4 4 4 4 4 8

SGR1...8/5 50P-2 5 5 5 5 5 5 5 5 16

SGR1...8/6 50P-2 TDLY 6 6 6 6 6 6 6 6 32

SGR1...8/7 51N 7 7 7 7 7 7 7 7 64
SGR1...8/8 51N TDLY 8 8 8 8 8 8 8 8 128
SGR1...8/9 50N 9 9 9 9 9 9 9 9 256
SGR1...8/10 50N TDLY 10 10 10 10 10 10 10 10 512
SGR1...8/11 46 Pickup 11 11 11 11 11 11 11 11 1024
SGR1...8/12 46 TDLY 12 12 12 12 12 12 12 12 2048
SGR1...8/13 49 Alarm 13 13 13 13 13 13 13 13 4096
SGR1...8/14 49 Trip 14 14 14 14 14 14 14 14 8192
SGR1...8/15 Ext. Trip 15 15 15 15 15 15 15 15 16384
SGR1...8/16 Open CB
16 16 16 16 16 16 16 16 32768
Command

SGR1...8/17 Close CB 17 17 17 17 17 17 17 17 65536

Command

SGR1...8/18 Definate
18 18 18 18 18 18 18 18 131072
Trip Alarm

SGR1...8/19 CB
Reclosing 19 19 19 19 19 19 19 19 262144
Failed

SGR1...8/20 Shot Due 20 20 20 20 20 20 20 20 524288

SGR1...8/21 AR Lockout 21 21 21 21 21 21 21 21 1048576
SGR1...8/22 ARC Trip 22 22 22 22 22 22 22 22 2097152

SGR1...8/23 L> 23 23 23 23 23 23 23 23 4194304

ΣSGR1

ΣSGR2

ΣSGR3

ΣSGR4

ΣSGR5

ΣSGR6

ΣSGR7

ΣSGR8

Checksum
OutpSignREF610_b

Fig. 4.1.4.10.-2 Output signal matrix

53

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

Table 4.1.4.10-8 SGR1...SGR3

Default setting
Switch Function
SGR1...SGR3 SGR4...SGR5 SGR6...SGR8
1)
SGR1...8/1 Pickup signal from element 0 1 0
51P
SGR1...8/2 Trip signal from element 51P 1 0 0
SGR1...8/3 Pickup signal from element 0 1 0
50P-1
SGR1...8/4 Trip signal from element 50P-1 1 0 0
SGR1...8/5 Pickup signal from element 0 1 0
50P-2
SGR1...8/6 Trip signal from element 50P-2 1 0 0
SGR1...8/7 Pickup signal from element 0 1 0
51N
SGR1...8/8 Trip signal from element 51N 1 0 0
SGR1...8/9 Pickup signal from element 0 1 0
50N
SGR1...8/10 Trip signal from element 50N 1 0 0
SGR1...8/11 Pickup signal from element 46 0 1 0
SGR1...8/12 Trip signal from element 46 1 0 0
SGR1...8/13 Alarm signal from element 49 0 1 0
SGR1...8/14 Trip signal from element 49 1 0 0
SGR1...8/15 External trip signal 0 0 0
SGR1...8/16 Open CB command from AR 0 0 0
SGR1...8/17 Close CB command from AR 0 0 0
SGR1...8/18 Definite trip alarm signal from 0 0 0
AR
SGR1...8/19 CB reclosing failed signal from 0 0 0
AR
SGR1...8/20 Shot due signal from AR 0 0 0
SGR1...8/21 Lockout signal from AR 0 0 0
SGR1...8/22 Trip signal from element ARC 1 0 0
SGR1...8/23 Light signal output 0 0 0
ΣSGR1...8 2108074 5461 0
1) If the optional I/O module has not been installed, dashes will be shown on the LCD and “9999999”
when the parameter is read via the SPA bus.

SGL1...SGL8
The signals are routed to LED1 with the switches of switchgroup SGL1, to LED2
with those of SGL2, and so forth.

Table 4.1.4.10-9 SGL1...SGL8

Switch Function Default setting
SGL1...8/1 Trip signal from element 51P 0
SGL1...8/2 Trip signal from element 50P-1 0
SGL1...8/3 Trip signal from element 50P-2 0
SGL1...8/4 Trip signal from element 51N 0
SGL1...8/5 Trip signal from element 50N 0

54

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

Table 4.1.4.10-9 SGL1...SGL8

Switch Function Default setting
SGL1...8/6 Trip signal from element 46 0
SGL1...8/7 Alarm signal from element 49 0
SGL1...8/8 Trip signal from element 49 0
SGL1...8/9 Trip lockout signal 0
SGL1...8/10 Definite trip alarm signal from AR 0
SGL1...8/11 Shot due signal from AR 0
SGL1...8/12 Lockout signal from AR 0
SGL1...8/13 CB position open 0
SGL1...8/14 CB position closed 0
SGL1...8/15 DI1 signal 0
SGL1...8/16 DI2 signal 0
SGL1...8/17 DI3 signal 0
SGL1...8/18 DI4 signal 0
SGL1...8/19 DI5 signal 0
SGL1...8/20 Trip signal from element ARC 0
SGL1...8/21 Light signal output 0
ΣSGL1...SGL8 0

Auto-reclose SG1...SG3
Switchgroup SG1 is used for blocking the initiation of one or several auto-reclose
shots, SG2 for blocking of protection elements at one or several auto-reclose shots,
and SG3 for disabling the AR function as follows:

Table 4.1.4.10-10SG1
Default
Switch Function
setting
SG1/1 Blocking of initiation of shot 1 by the trip signal from element 50P-1 0
SG1/2 Blocking of initiation of shot 1 by the external AR initiation signal 0
SG1/3 Blocking of initiation of shot 1 by the trip or delayed pickup signal from 0
element 51P
SG1/4 Blocking of initiation of shot 1 by the trip or delayed pickup signal from 0
element 51N or the trip signal from element 50N
SG1/5 Blocking of initiation of shot 2 and 3 by the trip signal from element 0
50P-1
SG1/6 Blocking of initiation of shot 2 and 3 by the external AR initiation signal 0
SG1/7 Blocking of initiation of shot 2 and 3 by the trip or delayed pickup signal 0
from element 51P
SG1/8 Blocking of initiation of shot 2 and 3 by the trip or delayed pickup signal 0
from element 51N or the trip signal from element 50N
• When the switch is in position 1, shot initiation is blocked.
ΣSG1 0

55

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

Table 4.1.4.10-11SG2 1)
Switch Function Default setting
SG2/1 Blocking of tripping of element 51P at shot 1 0
SG2/2 Blocking of tripping of element 50P-1 at shot 1 0
SG2/3 Blocking of tripping of element 50P-2 at shot 1 0
SG2/4 Blocking of tripping of element 51N at shot 1 0
SG2/5 Blocking of tripping of element 50N at shot 1 0
SG2/6 Blocking of tripping of element 51P at shots 2 and 3 0
SG2/7 Blocking of tripping of element 50P-1 at shots 2 and 3 0
SG2/8 Blocking of tripping of element 50P-2 at shots 2 and 3 0
SG2/9 Blocking of tripping of element 51N at shots 2 and 3 0
SG2/10 Blocking of tripping of element 50N at shots 2 and 3 0
• When the switch is in position 1, the element is blocked. 0
ΣSG2 0
1) The blocking is active until the set cutout time or the set reclaim time elapses or the AR function is
locked out.

Table 4.1.4.10-12SG3
Switch Function Default setting
SG3/1 Disable of the AR function by the trip signal from element 50P-2 1
SG3/2 Disable of the AR function by the trip signal from element 50N 1
SG3/3 Disable of the AR function by the alarm signal from element 49 1
SG3/4 Disable of the AR function by the trip signal from element 46 1
• When the switch is in position 1, the AR function is disabled.
SG3/5 Resetting targets at CB reclosing 0
• When the switch is in position 1, targets are reset when the AR
function issues a reclosing command to the circuit breaker.
ΣSG3 15

New trip target timer

The new trip target timer can be configured to allow a second trip target on the LCD.
When several protection elements trip, the first trip target will be displayed until the
time, as specified by the NEW TRIP IND. setting value, has expired. After this,
a new trip target can displace the old one. The basic protection functions are not
affected by the NEW TRIP IND. setting.

Table 4.1.4.10-13 New trip target timer

Setting Default
Setting Description
range setting
New trip target New trip target timer in minutes 0...998 60
No new trip target allowed until the previous 999
one has been manually cleared.

56

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

Non-volatile memory settings

The table below presents data which can be configured to be stored in the battery
backed-up non-volatile memory. All of the functions mentioned below can be
selected separately with switches 1...5 either via the HMI or the SPA bus.

Table 4.1.4.10-14 Memory settings

Default
Setting Switch Function
setting
Non-volatile memory 1 • 0 = operation target messages and LEDs will 1
settings be cleared
• 1 = operation target messages and LEDs will
be retained 1)
2 • 1 = disturbance recorder data will be 1
retained1)
3 • 1 = event codes will be retained 1) 1
4 • 1 = recorded data and information on the 1
number of pickups of the protection elements
will be retained 1)
5 • 1 = the real-time clock will be running also 1
during loss of auxiliary voltage 1)

Checksum 31
1) The prerequisite is that the battery has been inserted and is charged.

Note!
When all switches have been set to zero, the battery supervision will be disabled.

57

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

4.1.4.11. Technical data on protection functions

Table 4.1.4.11-1 Elements 51P, 50P-1 and 50P-2
Feature Element 51P Element 50P-1 Element 50P-2
Set pickup value, 51P,
50P-1 and 50P-2
• at definite-time 0.30...5.00 x In (CT) 0.50...35.0 x In (CT) 0.50...35.0 x In (CT)
characteristic
• at IDMT (mode)
characteristic
Pickup time, typical 55 ms 30 ms 30 ms
Time/current characteristic
• definite-time
operate time, 51P TDLY, 0.05...300 s 0.04...300 s 0.04...300 s
50P-1 TDLY and 50P-2
TDLY
• IDMT (mode) according to Extremely inverse
IEC 60255-3 Very inverse
Normal inverse
Long-time inverse
time multiplier, 51P TD 0.05...1.00
IEC
• Special type of IDMT RI-type inverse
(mode) characteristic

time multiplier, 51P TD 0.05...1.00

IEC
• IDMT (mode) according to Extremely inverse
IEEE C37.112 Very inverse
Moderately inverse
time dial, 51P TD ANSI 1...15
Resetting time, maximum 50 ms 2) 50 ms 50 ms
Retardation time, typical 30 ms 30 ms 30 ms
Set resetting time, 51P 0.05...2.50 s
RSET
Drop-off/pick-up ratio, 0.96 0.96 0.96
typical
Operate time accuracy
• at definite-time ±2% of the set ±2% of the set ±2% of the set
characteristic operate time or ±25 operate time or ±25 operate time or ±25
ms ms ms
• at IDMT (mode) 5
characteristic according to
IEC 60255-3: accuracy
class index E
• at IDMT (mode) ±7% of the
characteristic according to calculated operate
IEEE C37.112 time
• at RI-type characteristic ±7% of the
calculated operate
time

58

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

Table 4.1.4.11-1 Elements 51P, 50P-1 and 50P-2

Feature Element 51P Element 50P-1 Element 50P-2
Operation accuracy
• 0.3...0.5 x In (CT) ±5% of the set
pickup value or
0.05% In (CT)
• 0.5...5.0 x In (CT) ±3% of the set ±3% of the set ±3% of the set
pickup value pickup value pickup value
• 5.0...35.0 x In (CT) ±3% of the set ±3% of the set
pickup value pickup value
1) At IDMT (mode) characteristic, the relay allows settings above 2.5 x In (CT) for element 51P, but
regards any setting >2.5 x In (CT) as equal to 2.5 x In (CT).
2) Resetting time of the trip signal.

59

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

Table 4.1.4.11-2 Elements 51N and 50N

Feature Element 51N Element 50N
Set pickup value, 51N and 50N
• at definite-time characteristic 1.0...100% In (CT) 5.0...400% In (CT)
• at IDMT (mode) characteristic 1.0...40% In (CT) 1)
Pickup time, typical 60 ms 40 ms
Time/current characteristic
• definite time
operate time, 51N TDLY and 0.05...300 s 0.05...300 s
50N TDLY
• IDMT (mode) according to IEC Extremely inverse
60255-3 Very inverse
Normal inverse
Long-time inverse
time multiplier, 51N TD IEC 0.05...1.00
• Special type of IDMT (mode) RI-type inverse
characteristic

time multiplier, 51N TD IEC 0.05...1.00

• IDMT (mode) according to Extremely inverse
IEEE C37.112 Very inverse
Moderately inverse
time dial, 51N TD ANSI 1...15
Resetting time, maximum 50 ms 2) 50 ms
Retardation time, typical 30 ms 30 ms
Set resetting time, 51N RSET 0.05...2.50 s
Drop-off/pick-up ratio, typical 0.96 0.96
Operate time accuracy
• at definite-time characteristic ±2% of the set operate ±2% of the set operate
time or ±25 ms time or ±25 ms
• at IDMT (mode) characteristic 5
according to IEC 60255-3:
accuracy class index E
• at IDMT (mode) characteristic ±7% of the calculated
according to IEEE C37.112 operate time
• at RI-type characteristic ±7% of the calculated
operate time
Operation accuracy
• 1.0...10.0% In (CT) ±5% of the set pickup ±5% of the set pickup
value or value or
0.05% In (CT) 0.05% In (CT)
• 10.0...100% In (CT) ±3% of the set pickup ±3% of the set pickup
value value
• 100...400% In (CT) ±3% of the set pickup
value
1) At IDMT (mode) characteristic, the relay allows settings above 0.4 x In (CT) for element 51N, but
regards any setting >0.4 x In (CT) as equal to 0.4 x In (CT).
2) Resetting time of the trip signal.

60

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

Table 4.1.4.11-3 Element 49

Feature Value
Set full load current, FLA 0.30...1.50 x In (CT)
Set alarm level, 49 ALARM 50...100%
Trip level, 49 Trip 100%
Time constant, τ 1...200 min
Operate time accuracy
• I/FLA >1.2 ±2% of the set
operate time or
±1 s

Table 4.1.4.11-4 Element 46

Feature Value
Set pickup value, 46
• at definite-time characteristic 10...100%
Pickup time, typical 100 ms
Time/current characteristics
• definite time
operate time, 46 TDLY s 1...300 s
Resetting time, maximum 70 ms
Drop-off/pick-up ratio, typical 0.90
Operate time accuracy
• at definite-time characteristic ±2% of the set
operate time or ±25
ms
Operation accuracy
• 10...100% ±3% of the set
pickup value and ±1
unit

Table 4.1.4.11-5 Element ARC and L>

Feature Value
Element ARC
Set current limit
• Arc 50P 0.5...35.0 x In (CT)
• Arc 50N 5.0...400% In (CT)
Operate time < 15 ms 1)
Resetting time 30 ms
Operation accuracy ±7% of the set
pickup value
L>
Activation time of L> < 15 ms
Resetting time 20 ms
1) Appliesonly if a non-trip output contact (SO1...5) is used. If a trip output contact (PO1...3) is used,
2...3 ms will be added.

61

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

ArcSensitREF610_a

Fig. 4.1.4.11.-1 Relative sensitivity of lens sensors

Table 4.1.4.11-6 Auto-reclose function

Feature Value
Number of shots 0...3
CB Closing time 0.1...10 s
Pickup delay of element 51P 0...300 s
Pickup delay of element 51N 0...300 s
Reset time 3...300 s
Cutout time 0.1...300 s
Open time of shot 1 0.1...300 s
Open time of shot 2 0.1...300 s
Open time of shot 3 0.1...300 s
Operate time accuracy ±2% of the set time
and ±25 ms

Table 4.1.4.11-7 CBFAIL

Feature Value
Set operate time 0.10...60.0 s
Phase-current threshold for
external triggering of the CBFAIL
• pick-up/drop-off 0.08/0.04 x In (CT)

62

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

4.1.5. Trip-circuit supervision

The trip-circuit supervision (TCS) detects open circuits, both when the circuit
breaker is open and closed, and trip-circuit supply failure.
The trip-circuit supervision is based on the constant current injection principle: by
applying an external voltage, a constant current is forced to flow through the
external trip circuit. If the resistance of the trip circuit exceeds a certain limit, due to
oxidation or a bad contact, for instance, the trip-circuit supervision will be activated
and a warning will appear on the LCD together with a fault code. The warning signal
from the trip-circuit supervision can also be routed to SO2 by setting switch SGF1/
8 to 1.
Under normal operating conditions, the applied external voltage is divided between
the relay’s internal circuit and the external trip circuit so that at least 20 V remains
over the relay’s internal circuit. If the external trip circuit’s resistance is too high or
the internal circuit’s too low, due to welded relay contacts, for instance, the voltage
over the relay’s internal circuit will fall below 20 V (15...20 V), which will activate
the trip-circuit supervision.
The operation condition is:
U c – ( Rext + R int + R s ) × I inj ≥ 20Vac ⁄ dc
where
• Uc = operating voltage over the supervised trip circuit
• Iinj = current flowing through the trip circuit, ~1.5 mA
• Rext = external shunt resistor
• Rint = internal shunt resistor, 1 kΩ
• Rs = trip coil resistance
The external shunt resistor is used to enable trip-circuit supervision also when the
circuit breaker is open.
The resistance of the external shunt resistor is to be calculated so that it does not
cause malfunction of the trip-circuit supervision or affect the operation of the trip
coil. Too high a resistance will cause too high a voltage drop, which in turn will
result in the operation conditions not being fulfilled, whereas too low a resistance
may cause faulty operation of the trip coil.
The following values are recommended for the external resistor, Rext:

Table 4.1.5-1 Recommended values for Rext

Operating voltage, Uc Shunt resistor Rext
48 V dc 1.2 kΩ, 5 W
60 V dc 5.6 kΩ, 5 W
110 V dc 22 kΩ, 5 W
220 V dc 33 kΩ, 5 W

The circuit breaker is to be provided with two external contacts, one opening and one
closing contact. The closing contact is to be connected in parallel with the external
shunt resistor, which will enable trip-circuit supervision when the circuit breaker is

63

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

closed. The opening contact, on the contrary, is to be connected in series with the
external shunt resistor, which will enable trip-circuit supervision when the circuit
breaker is open; see Fig. 4.1.5.-1.
Trip-circuit supervision can be selected either via the HMI or with SPA parameter
V113.

X4.1

18 +
PO1

Rint
Rext Rs
19
16
TCS
17 -

7
8
SO2

6
HW
SW SGF1/8

TRIP-CIRCUIT

TCSopenREF610_a
SUPERVISION
TCS STATE WARNING HMI

Fig. 4.1.5.-1 Connecting the trip-circuit supervision using two external contacts
and the external resistor in the trip circuit

4.1.6. Trip lockout function

The trip lockout function is used to prevent accidental closing of the circuit breaker
after a trip. The trip lockout function must be locally reset with a separate reset
command before the circuit breaker can be closed again. This function is useful
when the trip output contact of the relay is latched or the open circuit of the circuit
breaker remains activated.
The trip lockout function is selected in SGF1. When selected, PO3 will be dedicated
to this function. As long as no trip occurs, PO3 will be closed.
Every signal which has been routed to PO3 via the output signal matrix will activate
the trip lockout function and open the contacts of PO3. When the contacts have
opened, they will be locked into the open state. The trip lockout function can also be
activated externally, via a digital input.
The trip lockout function can be reset via a digital input, the HMI or SPA parameter
V103, but not before the signal which activated the function has been reset.

64

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

In case of loss of auxiliary power when the trip lockout function is in use, the
contacts of PO3 will return to the same state as before the loss, provided that the
battery has been inserted and is charged. If no battery has been inserted, the trip
lockout function will be activated and the contacts of PO3 will remain open when
the auxiliary power is switched on again.

4.1.7. Trip counters for circuit-breaker condition monitoring

The trip counters for circuit-breaker condition monitoring provide history data,
which can be used for circuit-breaker service scheduling. With this information, the
service cycle can be estimated for the future.
The monitoring function consists of four counters, which count the number of trip
signals generated to the circuit breaker by REF 610. Every time a element generates
a trip signal, the corresponding counter value will be increased by one. The number
of trips is stored in the non-volatile EEPROM memory.
There are separate counters for the different protection elements because breaking
the current in different fault situations wears the circuit breaker differently. Each
overcurrent element (51P, 50P-1 and 50P-2) has its own trip counter, whereas there
is a common trip counter for elements 51N, 50N, 46, 49 and ARC, the AR function
(Open CB Command) and the external trip.
The counters can be read via the HMI or SPA parameters V9...V12 and cleared via
SPA parameter V166. When a counter reaches its maximum value, it will roll over.
Note!
In case several elements trip during the same fault sequence, only the counter of the
element which tripped first will be incremented.

4.1.8. Target LEDs and operation target messages

The operation of REF 610 can be monitored via the HMI by means of LED targets
and text messages on the LCD. On the front panel of the relay there are three target
LEDs with fixed functionality: a green target LED (ready), a yellow target LED
(pickup/alarm) and a red target LED (trip). In addition, there are eight
programmable LEDs and an target LED for front communication. Refer to the
Operator’s Manual for a more thorough presentation.
The messages on the LCD have a certain priority order. If different types of targets
are activated simultaneously, the message with the highest priority will appear on
the LCD.
The priority order of the messages:
1. CBFAIL
2. Trip
3. Pickup/Alarm

4.1.9. Demand values

REF 610 provides three different kinds of demand values. The first value shows the
average current of all three phases measured during one minute. The value is
updated once a minute. The second value shows the average current during an
adjustable time range, ranging from 0 to 999 minutes, with an accuracy of one

65

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

minute. This value is updated at the expiration of each time range. The third value
shows the highest one-minute average current value measured during the previous
time range. However, if the time range is set to zero, only the one-minute and the
maximum demand value will be shown. The maximum value is the highest
one-minute mean value since the last reset.
The demand values can be set to zero through serial communication using SPA
parameter V102. The demand values will also be reset if SPA parameter V105 is
changed or the relay is reset.

4.1.10. Commissioning tests

The following two product functions can be used during the commissioning of the
relay: function test and digital input test.
The function test is used for testing the configuration as well as the connections from
the relay. By selecting this test, the internal signals from the protection elements, the
external trip signal and the IRF function can be activated one by one. Provided that
the signals have been set to be routed to the output contacts (PO1...PO3 and
SO1...SO5) with the switches of SGR1...8, the output contacts will be activated and
their corresponding event codes generated when the test is run. However, activation
of the internal signals from the protection elements, the signals from the auto-reclose
function, the external trip signal and the IRF function will not generate an event
code.
The digital input test is used for testing the connections to the relay. The state of the
digital inputs can be monitored via the HMI.
Refer to the Operator’s Manual for instructions on how to perform the tests.

4.1.11. Disturbance recorder

4.1.11.1. Function
REF 610 features an integrated disturbance recorder for recording monitored
quantities. The recorder continuously captures the curve forms of the currents as
well as the status of both internal and digital input signals and stores these in the
memory.
Triggering of the recorder will generate an event code. After the recorder has been
triggered, it will continue to record data for a pre-defined post-triggering time. An
asterisk will be shown on the LCD on completion of the recording. The status of the
recording can also be viewed using SPA parameter V246.
As soon as the recorder has been triggered and the recording has finished, the
recording can be uploaded and analysed by means of a PC provided with a special
program.

4.1.11.2. Disturbance recorder data

One recording contains data from the four analogue channels and up to eight digital
channels. The analogue channels, whose data is stored either as RMS curves or as
instantaneous measured values, are the currents measured by the relay. The digital

66

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

channels, referred to as digital signals, are pickup and trip signals from the
protection elements, the alarm signal from element 49, the signals from the auto-
reclose function and the digital input signals linked to the relay.
The user can select up to eight digital signals to be recorded. If more than eight
signals are selected, the first eight signals will be stored, beginning with the internal
signals followed by the digital input signals. The digital signals to be stored are
selected with parameters V238 and V243; see tables 4.1.17-6 and 4.1.17-7.
The recording length varies according to the selected sampling frequency. The RMS
curve is recorded by selecting the sampling frequency to be the same as the nominal
frequency of the relay. The sampling frequency is selected with SPA parameter
M15; see the table below for details.

Table 4.1.11.2-1 Sampling frequency

Nominal frequency Sampling frequency
Cycles
Hz Hz
50 800 250
400 500
50 1) 4000
60 960 250
480 500
60 1) 4000
1)
RMS curve.

Recording length:

Cycles
[ s ] = ----------------------------------------------------------------
-
Nominal frequency [ Hz ]

Changing the setting values of parameters M15, V238 and V243 is allowed only
when the recorder is not triggered.
The post-triggering recording length defines the time during which the recorder
continues to store data after it has been triggered. The length can be changed with
SPA parameter V240. If the post-triggering recording length has been defined to be
the same as the total recording length, no data stored prior to the triggering will be
retained in the memory. By the time the post-triggering recording finishes, a
complete recording will have been created.
Triggering of the recorder immediately after it has been cleared or the auxiliary
voltage connected may result in a shortened total recording length. Disconnection of
the auxiliary voltage after the recorder has been triggered, but before the recording
has finished, on the other hand, may result in a shortened post-triggering recording
length. This, however, will not affect the total recording length.
At a power reset, triggered recorder data will be retained in the memory provided
that it has been defined non-volatile.

4.1.11.3. Control and target of disturbance recorder status

It is possible to control and monitor the recording status of the disturbance recorder
by writing to and reading SPA parameters M1, M2 and V246. Reading SPA
parameter V246 will return either the value 0 or 1, indicating whether the recorder

67

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

has not been triggered or triggered and ready to be uploaded. Event code E31 will
be generated the moment the disturbance recorder is triggered. If the recorder is
ready to be uploaded, this will also be indicated by an asterisk shown in the lower
right-hand corner of the LCD when it is in the idle mode.
Writing the value 1 to SPA parameter M2 will clear the recorder memory, restart the
recording of new data and enable the triggering of the recorder. Recorder data can
be cleared by performing a master reset, i.e. clearing targets and memorized values
and unlatching output contacts. Writing the value 2 to SPA parameter V246 will
restart the unloading process by setting the time stamp and the first data ready to be
read.

4.1.11.4. Triggering
The user can select one or several internal or digital input signals to trigger the
disturbance recorder, either on the rising or falling edge of the signal(s). Triggering
on the rising edge means that the post-triggering recording sequence will start when
the signal is activated. Correspondingly, triggering on the falling edge means that
the post-triggering recording sequence will start when the active signal is reset. The
trigger signal(s) and the edge are selected with SPA parameters V236...V237 and
V241...V242; see tables 4.1.17-6 and 4.1.17-7. The recorder can also be triggered
manually with SPA parameter M1.
Triggering of the disturbance recorder is only possible if the recorder has not already
been triggered.

4.1.11.5. Settings and unloading

The setting parameters for the disturbance recorder are V parameters V236...V238,
V240...V243 and V246, and M parameters M15, M18, M20 and M80...M83.
Unloading correct information from the recorder requires that M80 and M83 have
been set. Unloading is done using a PC application. The uploaded recorder data is
stored in separate files defined by the comtrade® format.

4.1.11.6. Event code of the disturbance recorder

The disturbance recorder generates an event code on triggering (E31) and clearing
(E32) the recorder. The event mask is determined using SPA parameter V155.

4.1.12. Recorded data of the last events (Fault Summary)

REF 610 records up to five events. This enables the user to analyze the last five fault
conditions in the electrical power network. Each event includes the measured
currents, pickup durations and time stamp, for instance. Additionally, information
on the number of pickups, trips and auto-reclose shots is provided.
Recorded data is non-volatile by default, provided that the battery has been inserted
and is charged. A master reset, i.e. clearing of targets and memorized values and
unlatching of output contacts, will erase the contents of the stored events and the
number of pickups.

68

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

Note!
The number of trips and auto-reclose shots is stored in the non-volatile EEPROM
memory and will thus not be cleared when performing a master reset. The number
of trips can be erased by entering the value 1 and the number of auto-reclose shots
by entering the value 2 into parameter V166.
REF 610 collects data during fault conditions. When all pickup or thermal alarm
signals have been reset or a element trips, the collected data and time stamp will be
stored as “EVENT1” and the previously stored events will move one step forward.
When a sixth event is stored, the oldest event will be cleared.

Table 4.1.12-1 Recorded data

REGISTER Data description
EVENT1 • Phase current la, measured as a multiple of the rated current, In (CT), is
displayed in two registers: the main register and the sub register. When a
element picks up but does not trip, the maximum fault current during the
pick-up period will be stored in both the main register and the sub register.
When a element trips, the fault current at the time of the trip will be stored in
the main register and the maximum fault current during the pick-up period in
the sub register. The same applies to phase currents lb, lc and ln.
• The phase unbalance, I (unbal), as a percentage of the maximum phase
current value. When the element picks up but does not trip, the maximum
phase unbalance value during the pick-up period will be stored. When the
element trips, the fault unbalance at the time of the trip will be stored.
• Thermal level, as a percentage of the maximum thermal level of the cable, at
activation of a pickup or alarm signal. If the thermal protection element has
been set out of operation, dashes will be shown on the LCD and “999” when
read via serial communication.
• The maximum thermal level during the time the pickup or alarm signal was
active, as a percentage of the maximum thermal level of the cable, or in case
of a trip, the thermal level, as a percentage of the maximum thermal level of
the cable, at activation of a trip signal. If the thermal protection element has
been set out of operation, dashes will be shown on the LCD and “999” when
read via serial communication.
• Duration of the pickup of elements 51P, 50P-1, 50P-2, I (unbal), 51N and
50N, the trip of element ARC (local), the trip of element ARC (remote), and
of the external trip. A value other than zero indicates that the corresponding
element has picked up whereas the value 100% indicates that the operate
time of the element has elapsed, i.e. the element has tripped. If the operate
time of a element has elapsed but the element is blocked, the value will be
99% of the set or calculated operate time.
• Trip number in the auto-reclose sequence. The number 1...20 indicates the
order of the trip in the AR sequence. The value 1 indicates the first trip in the
AR sequence, the value 2 the second trip, and so forth. On expiration of the
set reset time, the value will pickup from 1 again. If the AR function has been
set out of operation, the value will always be 1.
• Time stamp for the event. The time when the collected data was stored. The
time stamp is displayed in two registers, one including the date expressed as
yy-mm-dd, and the other including the time expressed as HH.MM; SS.sss.
EVENT 2 Same as EVENT 1.
EVENT 3 Same as EVENT 1.
EVENT 4 Same as EVENT 1.
EVENT 5 Same as EVENT 1.
Number of • The number of times each protection element, 51P, 50P-1, 50P-2, I (unbal),
pickups 51N and 50N, has picked up, counting up to 999.

69

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

Table 4.1.12-1 Recorded data

REGISTER Data description
Number of • The number of times each protection element, 51P, 50P-1 and 50P-2, has
trips tripped. When the counters reach their maximum values (65535), it will roll
over.
• The number of times protection elements 51N, 50N, 49 or ARC elements
have issued a trip or an external trip. When the counter reaches its maximum
value (65535), it will roll over.
Number of • Number of AR shots (shot 1) initiated by the trip signal from element 50P-1,
AR shots counting up to 255
• Number of AR shots (shot 1) initiated by the digital input signal, counting up
to 255
• Number of AR shots (shot 1) initiated by the pickup or trip signal from
element 51P, counting up to 255
• Number of AR shots (shot 1) initiated by the pickup or trip signal from
element 51N, counting up to 255
• Number of AR shots (shot 2) initiated by the trip signal from element 50P-1,
counting up to 255
• Number of AR shots (shot 2) initiated by the digital input signal, counting up
to 255
• Number of AR shots (shot 2) initiated by the pickup or trip signal from
element 51P, counting up to 255
• Number of AR shots (shot 2) initiated by the pickup or trip signal from
element 51N, counting up to 255
• Number of AR shots (shot 3) initiated by the trip signal from element 50P-1,
counting up to 255
• Number of AR shots (shot 3) initiated by the digital input signal, counting up
to 255
• Number of AR shots (shot 3) initiated by the pickup or trip signal from
element 51P, counting up to 255
• Number of AR shots (shot 3) initiated by the pickup or trip signal from
element 51N, counting up to 255

4.1.13. Communication ports

REF 610 is provided with an optical communication port (infrared) on the front
panel. Rear communication is optional and requires a communication module,
which can be provided with either a plastic fibre-optic, combined fibre-optic (plastic
and glass) or RS-485 connection. The relay is connected to an automation system
via the rear connection. The optional rear communication module allows the use of
either the SPA bus, IEC 60870-5-103 or Modbus communication protocol.
For connection to the DNP 3.0 communication system, REF 610 can be provided
with an optional DNP 3.0 rear communication module with RS-485 connection.
For further information on optional rear communication module connections, refer
to section Serial communication connections.

70

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

FrConREF 610_b

Fig. 4.1.13.-1 Front connection (1) for local communication

The relay is connected to a PC used for local parameterization via the infrared port
on the front panel. The front connection allows the use of the SPA bus protocol only.
The optical front connection galvanically isolates the PC from the relay. The front
connection can be used in two different ways: wirelessly using a PC compatible to
the IrDA® Standard specifications or using a specific front communication cable
(ABB art. no 1MRS050698). The cable is connected to the serial RS-232 port of the
PC. The optical element of the cable is powered by RS-232 control signals. The
cable has a fixed baud rate of 9.6 kbps.
The following serial communication parameters are to be set for RS-232:

• Number of data bits 7

• Number of stop bits 1
• Parity even
• Baud rate 9.6 kbps

Relay data such as events, setting values and all input data and memorized values
can be read via the front communication port.
When setting values are altered via the front communication port, the relay will
check that the entered parameter values are within the permitted setting range. If an
entered value is too high or too low, the setting value will remain unchanged.
REF 610 has a counter which can be accessed via COMMUNICATION under
CONFIGURATION in the HMI menu. The counter value is set to zero when the relay
receives a valid message.

4.1.14. IEC 60870-5-103 remote communication protocol

REF 610 supports the IEC 60870-5-103 remote communication protocol
(henceforward referred to as the IEC_103) in the unbalanced transmission mode.
The IEC_103 protocol is used to transfer measurand and status data from the slave
to the master. However, the IEC_103 protocol cannot be used to transfer disturbance
recorder data.
The IEC_103 protocol can be used only through the rear connection of the relay on
the optional communication module. Connecting REF 610 to a fibre-optic
communication bus requires a fibre-optic communication module. The line-idle
state of the fibre-optic communication module can be selected either via the HMI or
the SPA bus. According to the IEC_103 standard, however, the line-idle state is

71

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

“light on”. To ensure communication, the line-idle state should be the same for both
the master and the slave device. The connection topology can be selected to be either
loop or star, the default being loop, and either via the HMI or the SPA bus. The
selected line-idle state and connection topology apply irrespective of which rear
communication protocol is active.
REF 610 will use the SPA bus protocol as default when the optional communication
module is in use. The protocol selection is memorized and will therefore always be
activated when the rear connection is in use. The baud rate can be selected either via
the HMI or the SPA bus. According to the IEC_103 standard, however, the baud rate
is 9.6 kbps. When the IEC_103 protocol is active, event masks are not in use.
Consequently, all events in the selected configuration set will be included in the
event reporting.
REF 610 is provided with two different selectable configuration sets, of which
configuration set 1 is used by default. Configuration set 1 is intended to be used
when the optional I/O module has not been installed. Configuration set 2 includes
additional information, e.g. output contact events 6...8 (SO3...SO5) and digital input
events 3...5 (DI3...DI5), provided that the optional I/O module has been installed.
Function type and information number have been mapped into configuration sets
according to the IEC_103 standard to the extent that these have been defined by the
standard. If not defined by the standard, the type of function and/or the information
number have/has been mapped into a private range.
The tables below indicate the information mapping of the corresponding
configuration sets. The column GI indicates whether the status of the specified
information object is transmitted within the general interrogation cycle. The relative
time in messages with the type identification 2 is calculated as a time difference
between the occurred event and the event specified in the column Relative time. The
measurand multiplied by the normalize factor is proportional to the rated value.
Therefore, the maximum value of each measurand is the normalize factor multiplied
by the rated value.

72

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

Table 4.1.14-1 Information mapping of configuration set 1 and 2

Configuration

Configuration

identification
Information
Event code

Function

Relative
Event reason

number
set 1

set 2

Type
type

time
GI
Disturbance recorder E31/ X X 178 100 - - 1
Triggered/Cleared E32

HMI Password E33/ X X 178 101 - - 1

Opened/Closed E34

51P Pickup/Reset 1E1/ X X 160 84 X 1E1 2

1E2

51P Trip/Reset 1E3/ X X 160 90 - 1E1 2

1E4

50P-1 Pickup/Reset 1E5/ X X 162 94 X 1E5 2

1E6

50P-1 Trip/Reset 1E7/ X X 160 91 - 1E5 2

1E8

50P-2 Pickup/Reset 1E9/ X X 162 96 X 1E9 2

1E10

50P-2 Trip/Reset 1E11/ X X 162 98 - 1E9 2

1E12

51N Pickup/Reset 1E13/ X X 160 67 X 1E13 2

1E14

51N Trip/Reset 1E15/ X X 160 92 - 1E13 2

1E16

50N Pickup/Reset 1E17/ X X 162 95 X 1E17 2

1E18

50N Trip/Reset 1E19/ X X 160 93 - 1E17 2

1E20

46 Pickup/Reset 1E21/ X X 173 84 X 1E21 2

1E22

46 Trip/Reset 1E23/ X X 173 90 - 1E21 2

1E24

49 Pickup/Reset 1E25/ X X 184 84 X 1E25 2

1E26

49 Alarm/Reset 1E27/ X X 184 11 X - 1

1E28

49 Trip/Reset 1E29/ X X 184 90 - 1E25 2

1E30

ARC (light and 1E31/ X X 100 90 - 1E31 2

current) Trip/Reset 1E32

ARC (DI and current) 1E33/ X X 100 50 - 1E33 2

Trip/Reset 1E34

Arc light signal output 1E35/ X X 100 20 - - 1

Activated/Reset 1E36

73

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

Table 4.1.14-1 Information mapping of configuration set 1 and 2

Configuration

Configuration

identification
Information
Event code

Function

Relative
Event reason

number
set 1

set 2

Type
type

time
GI
Trip Lockout/Reset 1E37/ X X 10 223 X - 1
1E38

External Trip/Reset 1E39/ X X 10 222 - - 1

1E40

CBFAIL Activated/ 1E41/ X X 160 85 - - 1

Reset 1E42

PO1 Activated/Reset 2E1/ X X 251 27 X - 1

2E2

PO2 Activated/Reset 2E3/ X X 251 28 X - 1

2E4

PO3 Activated/Reset 2E5/ X X 251 29 X - 1

2E6

SO1 Activated/Reset 2E7/ X X 251 30 X - 1

2E8

SO2 Activated/Reset 2E9/ X X 251 31 X - 1

2E10

SO3 Activated/Reset 2E11/ - X 251 32 X - 1

2E12

SO4 Activated/Reset 2E13/ - X 251 33 X - 1

2E14

SO5 Activated/Reset 2E15/ - X 251 34 X - 1

2E16

DI1 Activated/ 2E17/ X X 249 231 X - 1

Deactivated 2E18

DI2 Activated/ 2E19/ X X 249 232 X - 1

Deactivated 2E20

DI3 Activated/ 2E21/ - X 249 233 X - 1

Deactivated 2E22

DI4 Activated/ 2E23/ - X 249 234 X - 1

Deactivated 2E24

DI5 Activated/ 2E25/ - X 249 235 X - 1

Deactivated 2E26

Shot 1 Initiated/ 3E1/ X X 169 101 - - 1

Ended 3E2

Shot 2 Initiated/ 3E3/ X X 169 102 - - 1

Ended 3E4

Shot 3 Initiated/ 3E5/ X X 169 103 - - 1

Ended 3E6

CB Position 3E7/ X X 240 160 - - 1

Open/Closed 3E8

74

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

Table 4.1.14-1 Information mapping of configuration set 1 and 2

Configuration

Configuration

identification
Information
Event code

Function

Relative
Event reason

number
set 1

set 2

Type
type

time
GI
Definite Trip Alarm/ 3E9/ X X 169 150 - - 1
Reset 3E10

AR Lockout/Reset 3E11/ X X 169 164 - - 1

3E12

Open CB Command/ 3E13/ X X 169 127 - - 1

Reset 3E14

Close CB Command/ 3E15/ X X 169 128 - - 1

Reset 3E16

CB Reclosing Failed/ 3E17/ X X 169 163 - - 1

Reset 3E18

CB Reclosing 3E19/ X X 169 162 - - 1

Disabled/Reset 3E20

AR Cancelled/Reset 3E21/ X X 169 130 - - 1

3E22

Table 4.1.14-2 Information mapping of configuration set 1 and 2

Configuration

Configuration

identification
Rated value

Information
Normalize

Function
Measurant

number
factor

set 1

set 2

Type
type

Current la 2.40 In (CT) X X 135 140 9

Current Ib 2.40 In (CT) X X

Current Ic 2.40 In (CT) X X

Current In 2.40 In (CT) X X

4.1.15. Modbus remote communication protocol

4.1.15.1. Protocol overview

The master/slave protocol Modbus was first introduced by Modicon Inc. and is
widely accepted as a communication standard for industrial device controllers and
PLCs. For the protocol definition, refer to “Modicon Modbus Protocol Reference
Guide PI-MBUS-300 Rev. E”.
The implementation of the Modbus protocol in REF 610 supports both the RTU and
the ASCII link mode. Both the link mode and the line setting parameters are
user-configurable.

75

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

The character codings of the link modes follow the protocol definition. The RTU
character format is presented in table 4.1.15.1-1 and the ASCII character format in
table 4.1.15.1-2:

Table 4.1.15.1-1 RTU character format

Coding system 8-bit binary
Bits per character 1 pickup bit
8 data bits, the least significant bit is sent first
1 bit for even/odd parity; no bit if parity is not used
1 stop bit if parity is used; 2 stop bits if parity is not used

Table 4.1.15.1-2 ASCII character format

Coding system Two ASCII characters representing a hexadecimal
number
Bits per character 1 pickup bit
7 data bits, the least significant bit is sent first
1 bit for even/odd parity; no bit if parity is not used
1 stop bit if parity is used; 2 stop bits if parity is not used

Note!
The turnaround time (response time) of REF 610 depends on the amount of data
requested in a query. Therefore, the turnaround time can vary between
approximately 20 and 100 milliseconds. However, a turnaround timeout no lower
than 150 ms is recommended for the Modbus master.
Note!
The data address range in the Modbus network follows the protocol definition and
picks up from 0. Consequently, the data addresses in table 4.1.15.2-5 will be
decreased by one when transferred over the network.
Note!
The Modbus data type digital input (DI) is commonly also referred to as 1X, coils
as 0X, input register (IR) as 3X and holding register (HR) as 4X, of which the former
will be used here. Thus, HR 123, for instance, can also be referred to as register
400123.

4.1.15.2. Profile of Modbus REF 610

The Modbus protocol (ASCII or RTU) is selected via the HMI and can be used only
through the rear connection of the relay on the optional communication module.
Modbus line settings, i.e. parity, CRC byte order and baud rate, can be adjusted
either via the HMI or the SPA bus.

76

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

The implementation of the Modbus protocol in REF 610 supports the following
functions:

Table 4.1.15.2-1 Supported application functions

Function code Function description
01 Read coil status
Reads the status of discrete outputs.
02 Read digital input status
Reads the status of discrete inputs.
03 Read holding registers
Reads the contents of output registers.
04 Read input registers
Reads the contents of input registers.
05 Force single coil
Sets the status of a discrete output.
06 Preset single register
Sets the value of a holding register.
08 Diagnostics
Checks the communication system between the master and
the slave.
15 Force multiple coils
Sets the status of multiple discrete outputs.
16 Preset multiple registers
Sets the value of multiple holding registers.
23 Read/write holding registers
Exchanges holding registers in one query.

Table 4.1.15.2-2 Supported diagnostic subfunctions

Code Name Description
00 Return query data The data in the query data field is returned (looped back) in
the response. The entire response is to be identical to the
query.
01 Restart The slave’s peripheral port is initialized and restarted and the
communication communication event counters are cleared. Before this, a
option normal response will be sent provided that the port is not in the
listen only mode. However, if the port is in the listen only
mode, no response will be sent.
04 Force listen only The slave is forced to enter the listen only mode for Modbus
mode communication.
10 Clear counters and All counters and the diagnostic register are cleared.
diagnostic register
11 Return bus The number of messages in the communications system
message count detected by the slave since its last restart, clear counters
operation or power up is returned in the response.
12 Return bus The number of CRC errors encountered by the slave since its
communication last restart, clear counters operation or power up is returned in
error count the response.
13 Return bus The number of Modbus exception responses sent by the slave
exception error since its last restart, clear counters operation or power up is
count returned in the response.
14 Return slave The number of messages addressed to the slave or broadcast
message count which the slave has processed since its last restart, clear
counters operation or power up is returned in the response.

77

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

Table 4.1.15.2-2 Supported diagnostic subfunctions

Code Name Description
15 Return slave no The number of messages addressed to the slave for which a
response count response (neither a normal response nor an exception
response) has not been sent since its last restart, clear
counters operation or power up is returned in the response.
16 Return slave The number of messages addressed to the slave for which a
NACK response NACK response has been sent is returned in the response.
count
18 Return bus The number of messages addressed to the slave for which it
character overrun has not been able to send a response due to a character
count overrun since its last pickup, clear counters operation or
power up is returned in the response.
Note!
Sending other subfunction codes than those listed above will cause an “Illegal data
value” response.
The Modbus protocol provides the following diagnostic counters:

Table 4.1.15.2-3 Diagnostic counters

Name Description
Bus message count The number of messages in the communications system
detected by the slave since its last pickup, clear counters
operation or power up.
Bus communication error The number of CRC or LRC errors encountered by the slave
count since its last restart, clear counters operation or power up.
Bus exception error count The number of Modbus exception responses sent by the slave
since its last restart clear counters operation or power up.
Slave message count The number of messages addressed to the slave or broadcast
which the slave has processed since its last restart, clear
counters operation or power up.
Slave no response count The number of messages addressed to the slave for which a
response (neither a normal response nor an exception
response) has not been sent since its last restart, clear
counters operation or power up.
Slave NACK response The number of messages addressed to the slave for which a
count NACK response has been sent.
Bus character overrun count The number of messages addressed to the slave for which it
has not been able to send a response due to a character
overrun since its last pickup, clear counters operation or power
up.

The following exception codes may be generated by the Modbus protocol:

Table 4.1.15.2-4 Possible exception codes

Code Name Description
01 Illegal function The slave does not support the requested function.
02 Illegal data The slave does not support the data address or the number of
address items in the query is incorrect.
03 Illegal data value A value contained in the query data field is out of range.
04 Slave device An unrecoverable error has occurred while the slave was
failure attempting to perform the requested task.

78

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

Note!
If an “Illegal data value” exception response is generated when attempting to preset
multiple registers, the contents of the register to which an illegal value has been
imposed and of the following registers will not be changed. Registers which have
already been preset will not be restored.
User-defined registers
Reading of unwanted data in a data block wastes bandwidth and complicates data
interpretation. For optimum efficiency in Modbus communication, data has
therefore been organized into consecutive blocks. In addition, a set of programmable
user-defined registers (UDR) has been defined in the holding register area.
The first sixteen holding registers, i.e. HR1...16, are user-defined registers. The
UDRs can be linked to any holding register, except for HR721...727, using SPA
parameters 504V1...504V16. However, one UDR cannot be linked to another, i.e.
linking cannot be nested. Each parameter contains the address of the holding register
to which the UDR is linked.
If a UDR is linked to a non-existent holding register, reading from the register will
fail and an “Illegal address exception” response will be sent. Giving the link address
the value 0 will disable the UDR. If the master reads from a disabled UDR, the value
0 will be returned.
The UDRs are mirrored in HR385…400.
Fault records
The data recorded during a fault sequence is called a fault record (FR). The slave
stores the five latest fault records. When a sixth record is stored, the oldest record
will be deleted. To read a fault record:
1. Write a preset single register command (function 06) to HR601 using a selection
code as data value.
2. Read the selected fault record (function 04) from HR601, register count 28.
Alternatively, a fault record can be read using one command (function 23) only.
Selection code 1: The master reads the oldest unread record
Status register 3 (HR403) informs whether there are unread fault records (see Fig.
4.1.15.2.-2). If there is one or several unread fault records, the master can read the
contents using selection code 1.
The fault record contains a sequence number which makes it possible for the master
to determine whether one or several unread fault records have been deleted due to
overflow. The master compares the sequence number to that of the previously read
fault record.
The slave keeps track of which fault record is currently the oldest unread. The master
can continue reading fault records for as long as Status register 3 indicates that there
are unread records.
Special case 1: If there are no unread fault records, the contents of the last read
record will be returned. If the buffer is empty, however, the registers will contain
only zeros. This is the only time when sequence number zero will appear.

79

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

Special case 2: If the master tries to read the next unread fault record without
entering selection code 1 again, the contents of the last read record will be returned.
Selection code 2: The master reads the oldest stored record
By resetting the read pointer using selection code 2, the master can read the oldest
stored fault record. After this, the master can continue reading the following records
using selection code 1, irrespective of whether they have been read before.
Note!
Resetting the read pointer will not affect the sequence number of the fault record.
Note!
A master reset, i.e. clearing of targets and memorized values and unlatching of
output contacts, will clear the fault records, after which the sequence number will
pickup from 1 again.
Event records
Modbus events are derived from SPA events. With a few exceptions, SPA events
update binary points in the DI and the packed HR area. Simultaneously, a
corresponding Modbus event record will be generated. The event record contains the
Modbus DI/CO data point address and the value to which the point has changed
(0 or 1). SPA events lacking a corresponding DI/CO data point are shown as SPA
channel and event code (informative event) in the event record. The maximum
capacity of the Modbus event buffer is 99 events. The time stamp of Modbus events
is extended to contain complete information, from date to millisecond. To read an
event record:
1. Write a preset single register command (function 06) to HR671 using a selection
code as data value.
2. Read the selected fault record (function 04) from HR672, register count 8.
Alternatively, a fault record can be read using one command (function 23) only.
Selection code 1: reading the oldest unread record
Status register 3 (HR403) informs whether there are unread event records (see Fig.
4.1.15.2.-2). If there is one or several unread event records, the master can read the
contents using selection code 1.
The event record contains a sequence number which makes it possible for the master
to determine whether one or several unread event records have been deleted due to
overflow by comparing it to the sequence number of the previously read event
record.
The slave keeps track of which event record is currently the oldest unread. The
master can continue reading event records for as long as Status register 3 indicates
that there are unread records.
Special case 1: If there are no unread event records, the contents of the last read
record will be returned. If the buffer is empty, however, the registers will contain
only zeros. This is the only time when sequence number zero will appear.
Special case 2: If the master tries to read the next unread event record without
entering selection code 1 again, the contents of the last read record will be returned.

80

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

Selection code 2: reading the oldest stored record

By resetting the read pointer using selection code 2, the master can read the oldest
stored event record. After this, the master can continue reading the following records
using selection code 1, irrespective of whether they have been read before.
Note!
Resetting the read pointer will not affect the sequence number of the event record.
Selection code -1...-99
With selection code -1...-99, the master can move backwards from the newest event
as many events as defined by the selection code and read that specific event record.
After this, the master can continue reading the following records using selection
code 1, irrespective of whether they have been read before.
Special case: If there is not as many events in the buffer as specified by the selection
code, the oldest stored event will be read.
Selection code 3
The Modbus event buffer is cleared with selection code 3. Clearing the buffer does
not require any read operation to follow.
Digital Inputs
As the master may not detect the state changes of all digital signals when scanning,
an additional change detect (CD) target bit will be created for every instantaneous
target point; see the example below.

Momentary

Change detect
Master reads

Master reads

Master reads

Master reads
ChDet_a

Fig. 4.1.15.2.-1 Change detection bit

If the instantaneous value of an target bit has changed two or more times since the
master last read it, the CD bit will be set to one. When the CD bit has been read, it
will be set to zero.
The instantaneous and the CD bit of a certain target point always occur as a pair in
the Modbus memory map.

81

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

Modbus data mapping

There are two types of monitoring data: digital targets and measurands. For
convenience and efficiency, the same data can be read from different data areas.
Measurands and other 16-bit values can be read either from the IR or HR
(read-only) area and digital target values from either the DI or coil (read-only) area.
It is also possible to read the status of the DIs as packed 16-bit registers from both
the IR and the HR area.
Consequently, all monitoring data can be read as consecutive blocks of data from the
IR or HR area.
The register and bit addresses are presented in table 4.1.15.2-5. Some register
structures are presented in separate sections below.
Note!
The HR and IR values are unsigned 16-bit integers unless otherwise specified.

Table 4.1.15.2-5 Mapping of Modbus data

HR/IR DI/Coil bit Value
Description Writeable Comment
address (.bit) address range
User-defined registers
UDR 1 1 or 385
UDR 2 2 or 386
UDR 3 3 or 387
UDR 4 4 or 388
UDR 5 5 or 389
UDR 6 6 or 390
UDR 7 7 or 391
UDR 8 8 or 392
UDR 9 9 or 393
UDR 10 10 or 394
UDR 11 11 or 395
UDR 12 12 or 396
UDR 13 13 or 397
UDR 14 14 or 398
UDR 15 15 or 399
UDR 16 16 or 400
Status registers
Status register 1 401 IRF code See Structure 1
Status register 2 402 Warning See Structure 1
codes
Status register 3 403 See Structure 1
Analogue data
Phase current Ia x In (CT) 404 0...5000 0...50 x In (CT)

Phase current Ib x In (CT) 405 0...5000 0...50 x In (CT)

Phase current Ic x In (CT) 406 0...5000 0...50 x In (CT)

Ground-fault current x In (CT) 407 0...800 0...800% In (CT)

Phase discontinuity x In (CT) 408 0...100 0...100% In (CT)

Digital data
Pickup signal from element 409.00 1 0/1 1 = activated
51P

82

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

Table 4.1.15.2-5 Mapping of Modbus data

HR/IR DI/Coil bit Value
Description Writeable Comment
address (.bit) address range
Pickup signal from element 409.01 2
51P CD
Trip signal from element 51P 409.02 3 0/1 1 = activated
Trip signal from element 51P 409.03 4
CD
Pickup signal from element 409.04 5 0/1 1 = activated
50P-1
Pickup signal from element 409.05 6
50P-1 CD
Trip signal from element 50P- 409.06 7 0/1 1 = activated
1
Trip signal from element 50P- 409.07 8
1 CD
Pickup signal from element 409.08 9 0/1 1 = activated
50P-2
Pickup signal from element 409.09 10
50P-2 CD
Trip signal from element 50P- 409.10 11 0/1 1 = activated
2
Trip signal from element 50P- 409.11 12
2 CD
Pickup signal from element 409.12 13 0/1 1 = activated
51N
Pickup signal from element 409.13 14
51N CD
Trip signal from element 51N 409.14 15 0/1 1 = activated
Trip signal from element 51N 409.15 16
CD
Pickup signal from element 410.00 17 0/1 1 = activated
50N
Pickup signal from element 410.01 18
50N CD
Trip signal from element 50N 410.02 19 0/1 1 = activated
Trip signal from element 50N 410.03 20
CD
Pickup signal from element 46 410.04 21 0/1 1 = activated
Pickup signal from element 410.05 22
46 CD
Trip signal from element 46 410.06 23 0/1 1 = activated
Trip signal from element 410.07 24
46 CD
Pickup signal from element 49 410.08 25 0/1 1 = activated
Pickup signal from element 49 410.09 26
CD
Alarm signal from element 49 410.10 27 0/1 1 = activated
Alarm signal from element 49 410.11 28
CD
Trip signal from element 49 410.12 29 0/1 1 = activated
Trip signal from element 49 410.13 30
CD
Trip signal from element ARC 410.14 31 0/1 1 = activated
(light and current)
Trip signal from element ARC 410.15 32
(light and current) CD

83

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

Table 4.1.15.2-5 Mapping of Modbus data

HR/IR DI/Coil bit Value
Description Writeable Comment
address (.bit) address range
Trip signal from element ARC 411.00 33 0/1 1 = activated
(light and DI)
Trip signal from element ARC 411.01 34
(light and DI) CD
Light signal output 411.02 35 0/1 1 = activated
Light signal output CD 411.03 36
Trip lockout signal 411.04 37 0/1 1 = activated
Trip lockout signal CD 411.05 38
External trip signal 411.06 39 0/1 1 = activated
External trip signal CD 411.07 40
CBFAIL 411.08 41 0/1 1 = failure
CBFAIL CD 411.09 42
Shot 1 411.10 43 0/1 1 = initiated
Shot 1 CD 411.11 44
Shot 2 411.12 45 0/1 1 = initiated
Shot 2 CD 411.13 46
Shot 3 411.14 47 0/1 1 = initiated
Shot 3 CD 411.15 48
CB position 412.00 49 0/1 1 = closed
0 = open
CB position CD 412.01 50
Definite trip alarm signal 412.02 51 0/1 1 = activated
Definite trip alarm signal CD 412.03 52
AR lockout signal 412.04 53 0/1 1 = activated
AR lockout signal CD 412.05 54
Open CB command 412.06 55 0/1 1 = activated
Open CB command CD 412.07 56
Close CB command 412.08 57 0/1 1 = activated
Close CB command CD 412.09 58
CB reclosing failed signal 412.10 59 0/1 1 = activated
CB reclosing failed signal CD 412.11 60
CB reclosing disabled 412.12 61 0/1 1 = activated
CB reclosing disabled CD 412.13 62
AR cancelled 412.14 63 0/1 1 = activated
AR cancelled CD 412.15 64
PO1 413.00 65 0/1 1 = activated
PO1 CD 413.01 66
PO2 413.02 67 0/1 1 = activated
PO2 CD 413.03 68
PO3 413.04 69 0/1 1 = activated
PO3 CD 413.05 70
SO1 413.06 71 0/1 1 = activated
SO1 CD 413.07 72
SO2 413.08 73 0/1 1 = activated
SO2 CD 413.09 74
SO3 413.10 75 0/1 1 = activated
SO3 CD 413.11 76
SO4 413.12 77 0/1 1 = activated
SO4 CD 413.13 78
SO5 413.14 79 0/1 1 = activated
SO5 CD 413.15 80
DI1 414.00 81 0/1 1 = activated

84

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

Table 4.1.15.2-5 Mapping of Modbus data

HR/IR DI/Coil bit Value
Description Writeable Comment
address (.bit) address range
DI1 CD 414.01 82
DI2 414.02 83 0/1 1 = activated
DI2 CD 414.03 84
DI3 414.04 85 0/1 1 = activated
DI3 CD 414.05 86
DI4 414.06 87 0/1 1 = activated
DI4 CD 414.07 88
DI5 414.08 89 0/1 1 = activated
DI5 CD 414.09 90
Disturbance recorder 414.10 91 0/1 1 = triggered
0 = cleared
Disturbance recorder CD 414.11 92
HMI password 414.12 93 0/1 1 = opened
0 = closed
HMI password CD 414.13 94
IRF 414.14 95 0/1 1 = activated
IRF CD 414.15 96
Warning 415.00 97 0/1 1 = activated
Warning CD 415.01 98
SPA event overflow 415.02 99
SPA event overflow CD 415.03 100 Only the CD bit
will be activated
in case of
overflow.
Recorded data
Fault record 601...628 See Structure 2
Event record 671...679 See Structure 3
Relay identification
Type designation of the relay 701...708 ASCII chars,
2 chars/register
Real-time clock
Time reading and setting 721...727 W See Structure 4
Additional analogue data
Thermal level 801 0...106 %
One-minute demand value 802 0...5000 0...50 x In (CT)
Demand value during the 803 0...5000 0...50 x In (CT)
specified time range
Maximum one-minute demand 804 0...5000 0...50 x In (CT)
value during the specified time
range
Element/phase which caused 805 HI word 0...131071 See table
the trip 4.1.17-3
806 LO word
Trip target code 807 0...21 See table
4.1.17-3
Number of pickups of element 808 0...999 Counter
51P
Number of pickups of element 809 0...999 Counter
50P-1
Number of pickups of element 810 0...999 Counter
50P-2

85

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

Table 4.1.15.2-5 Mapping of Modbus data

HR/IR DI/Coil bit Value
Description Writeable Comment
address (.bit) address range
Number of pickups of element 811 0...999 Counter
51N
Number of pickups of element 812 0...999 Counter
50N
Number of pickups of element 813 0...999 Counter
46
Number of trips of element 814 0...65535 Counter
51P
Number of trips of element 815 0...65535 Counter
50P-1
Number of trips of element 816 0...65535 Counter
50P-2
Number of trips of other 817 0...65535 Counter
elements
Number of AR shots (shot 1) 818 0...255 Counter
initiated by the trip signal from
element 50P-1
Number of AR shots (shot 1) 819 0...255 Counter
initiated by the digital input
signal
Number of AR shots (shot 1) 820 0...255 Counter
initiated by the pickup or trip
signal from element 51P
Number of AR shots (shot 1) 821 0...255 Counter
initiated by the pickup or trip
signal from element 51N
Number of AR shots (shot 2) 822 0...255 Counter
initiated by the trip signal from
element 50P-1
Number of AR shots (shot 2) 823 0...255 Counter
initiated by the digital input
signal
Number of AR shots (shot 2) 824 0...255 Counter
initiated by the pickup or trip
signal from element 51P
Number of AR shots (shot 2) 825 0...255 Counter
initiated by the pickup or trip
signal from element 51N
Number of AR shots (shot 3) 826 0...255 Counter
initiated by the trip signal from
element 50P-1
Number of AR shots (shot 3) 827 0...255 Counter
initiated by the digital input
signal
Number of AR shots (shot 3) 828 0...255 Counter
initiated by the pickup or trip
signal from element 51P
Number of AR shots (shot 3) 829 0...255 Counter
initiated by the pickup or trip
signal from element 51N
Control points
LED reset 501 W 1 1 = LED reset 1)
1)
Coil area, only writeable.

86

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

Structure 1
The status registers contain information on unread fault and event records, and relay
status. The registers are arranged as in the figure below.

15 8 7 0
401 Reserved IRF code

402 Warning code

403 FR ER Reserved SP MP
StatRegREF610_a

Fig. 4.1.15.2.-2 Status registers

When the value of the FR/ER bit is 1, there is one or several unread fault/event
records. If time synchronization is realized via a digital input, either the SP
(second-pulse) or MP (minute-pulse) bit will be activated. Refer to table 4.1.18-1
for IRF codes and table 4.1.18-2 for warning codes.
Structure 2
This structure contains data recorded during a fault sequence. Refer to section Fault
records for the reading method.

Table 4.1.15.2-6 Fault record

Address Signal name Range Comment
601 Latest selection code 1) 1...2 1 = read oldest
unread record
2 = read oldest
stored record
602 Sequence number 1...255
603 Unread records left 0...6
604 Time stamp of the recorded data, date 2 bytes: YY.MM
605 Time stamp of the recorded data, date and 2 bytes: DD.HH
time
606 Time stamp of the recorded data, time 2 bytes: MM.SS
607 Time stamp of the recorded data, time 0...999 0...999 ms
608 Phase current la 0...5000 0...50 x In (CT)
609 Phase current lb 0...5000 0...50 x In (CT)
610 Phase current lc 0...5000 0...50 x In (CT)
611 Ground-fault current 0...800 0...800% In (CT)
612 Phase discontinuity 0...100 0...100% In (CT)
613 Thermal level at pickup 0...106 0...106%
614 Thermal level at trip 0...106 0...106%
615 Maximum pick-up phase current la 0...5000 0...50 x In (CT)
616 Maximum pick-up phase current lb 0...5000 0...50 x In (CT)
617 Maximum pick-up phase current lc 0...5000 0...50 x In (CT)
618 Maximum pick-up ground-fault current 0...800 0...800% In (CT)
619 Pickup duration of element 51P 0...100 0...100%
620 Pickup duration of element 50P-1 0...100 0...100%
621 Pickup duration of element 50P-2 0...100 0...100%
622 Pickup duration of element 51N 0...100 0...100%

87

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

Table 4.1.15.2-6 Fault record

Address Signal name Range Comment
623 Pickup duration of element 50N 0...100 0...100%
624 Pickup duration of element 46 0...100 0...100%
625 Pickup duration of external trip 0/100 0/100%
626 Trip number of AR sequence 0...255
627 Pickup duration of element ARC (local) 0/100 0/100%
628 Pickup duration of element ARC (remote) 0/100 0/100%
1) Readable and writeable register.

Structure 3
This structure contains Modbus event records. Refer to section Event records for the
reading method.

Table 4.1.15.2-7 Event record

Address Signal name Range Comment
671 Latest selection code 1) 1...3 1 = read oldest
unread record
2 = read oldest
stored record
3 = clear Modbus
event buffer
-1...-99 -1...-99 = move to
the nth newest
record
672 Sequence number 1...255
673 Unread records left 0...99
674 Time stamp of the event, date 2 bytes: YY.MM
675 Time stamp of the event, date and 2 bytes: DD.HH
time
676 Time stamp of the event, time 2 bytes: MM.SS
677 Time stamp of the event, time 0...999 0...999 ms
678 Modbus DI point or informative event 0/1
(SPA channel)
• DI event 0 When MSB = 0, bits
14...0 indicate the DI
point.
• Informative event 1 When MSB = 1, bits
14...0 indicate the
SPA channel.
679 DI value or SPA event code
• DI event 0/1 In case of a DI
event, the register
will contain the DI
value.
• Informative event 0...63 In case of an
informative event,
the register will
contain the SPA
event code.
1)
Readable and writeable register.

88

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

Structure 4
The relay's real-time clock is stored in this structure. It can be updated by presetting
the whole register structure in one Modbus transaction.

Table 4.1.15.2-8 Real-time clock structure

Address Description Range
721 Year 0...99
722 Month 1...12
723 Day 1...31
724 Hour 0...23
725 Minute 0...59
726 Second 0...59
727 Hundredth of a 0...99
second

4.1.16. DNP 3.0 remote communication protocol

4.1.16.1. Protocol overview

The DNP 3.0 protocol was developed by Harris Control based on the early versions
of the IEC 60870-5 standard telecontrol protocol specifications. Today, the DNP
protocol specifications are controlled by the DNP Users Group.
The DNP protocol supports the ISO OSI (Open System Interconnection) based
model, which only specifies physical, data link and application layers. This reduced
protocol stack is referred to as Enhanced Performance Architecture (EPA). To
support advanced RTU functions and messages larger than the maximum frame
length as defined in the IEC 60870-1, the DNP 3.0 Data Link is to be used with a
transport pseudo-layer. As a minimum, the transport pseudo-layer implements
message assembly and disassembly services.

4.1.16.2. Protocol parameters of REF 610

The DNP parameters can all be adjusted using the Relay Setting Tool. For the DNP
parameters, refer to table 4.1.17-14.
Storing DNP 3.0 parameters
All DNP parameters are stored on the external DNP 3.0 module. After
parameterization with the Relay Setting Tool, REF 610 must be switched to the rear
communication mode for at least 10 seconds in order for the DNP parameters to be
replicated and stored onto the DNP module. However, this is necessary only if the
DNP parameters have been altered.

4.1.16.3. DNP 3.0 point list of REF 610

The DNP data points (binary, analogue and counters) of REF 610, presented in
tables 4.1.16.3-1... 4.1.16.3-3 below, are all in use as default.

89

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

The default class settings of the DNP points within the different event object groups
are:
• binary inputs change events: class 1
• analogue inputs change events: class 2
• counter change events: class 3
All static data points belong to class 0.
Unsolicited reporting is enabled for all event objects as default. However, the
point-specific enable/disable parameters are meaningless unless unsolicited
reporting has been enabled with SPA parameter 503V24.
The pointers to the scaling factors for analogue objects are all 0 as default.
Consequently, the DNP and Modbus analogue values of REF 610 are identical as
default.
All DNP process points can be edited using the Relay Setting Tool. Editing features
include:
• re-organizing, adding and removing DNP points
• assigning event classes to specific DNP points
• DNP point-specific enabling/disabling of unsolicited reporting
• defining deadbands for event reporting
• defining scaling factors for analogue values

Table 4.1.16.3-1 Binary data

DNP point Event UR Value
Description Comment
address class enable range
Pickup signal from element 51P 0 1 1 0/1 1 = activated
Trip signal from element 51P 1 1 1 0/1 1 = activated
Pickup signal from element 50P-1 2 1 1 0/1 1 = activated
Trip signal from element 50P-1 3 1 1 0/1 1 = activated
Pickup signal from element 50P-2 4 1 1 0/1 1 = activated
Trip signal from element 50P-2 5 1 1 0/1 1 = activated
Pickup signal from element 51N 6 1 1 0/1 1 = activated
Trip signal from element 51N 7 1 1 0/1 1 = activated
Pickup signal from element 50N 8 1 1 0/1 1 = activated
Trip signal from element 50N 9 1 1 0/1 1 = activated
Pickup signal from element 46 10 1 1 0/1 1 = activated
Trip signal from element 46 11 1 1 0/1 1 = activated
Pickup signal from element 49 12 1 1 0/1 1 = activated
Alarm signal from element 49 13 1 1 0/1 1 = activated
Trip signal from element 49 14 1 1 0/1 1 = activated
Trip signal from element ARC 15 1 1 0/1 1 = activated
(light and current)
Trip signal from element ARC (DI 16 1 1 0/1 1 = activated
and current)
Light signal output 17 1 1 0/1 1 = detected
Trip lockout signal 18 1 1 0/1 1 = activated
External trip signal 19 1 1 0/1 1 = activated
CBFAIL 20 1 1 0/1 1 = failure
Shot 1 21 1 1 0/1 1 = initiated
Shot 2 22 1 1 0/1 1 = initiated

90

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

Table 4.1.16.3-1 Binary data

DNP point Event UR Value
Description Comment
address class enable range
Shot 3 23 1 1 0/1 1 = initiated
CB position 24 1 1 0/1 1 = closed
Definite trip alarm signal 25 1 1 0/1 1 = activated
AR lockout signal 26 1 1 0/1 1 = activated
Open CB command 27 1 1 0/1 1 = activated
Close CB command 28 1 1 0/1 1 = activated
CB reclosing failed signal 29 1 1 0/1 1 = activated
CB reclosing disabled 30 1 1 0/1 1 = activated
AR cancelled 31 1 1 0/1 1 = activated
PO1 32 1 1 0/1 1 = activated
PO2 33 1 1 0/1 1 = activated
PO3 34 1 1 0/1 1 = activated
SO1 35 1 1 0/1 1 = activated
SO2 36 1 1 0/1 1 = activated
SO3 37 1 1 0/1 1 = activated
SO4 38 1 1 0/1 1 = activated
SO5 39 1 1 0/1 1 = activated
DI1 40 1 1 0/1 1 = activated
DI2 41 1 1 0/1 1 = activated
DI3 42 1 1 0/1 1 = activated
DI4 43 1 1 0/1 1 = activated
DI5 44 1 1 0/1 1 = activated
Disturbance recorder 45 1 1 0/1 1 = triggered
0 = cleared
HMI password 46 1 1 0/1 1 = opened
0 = closed
IRF 47 1 1 0/1 1 = activated
Warning 48 1 1 0/1 1 = activated
SPA event overflow 49 1 1 0/1 1 = activated

Table 4.1.16.3-2 Analogue data

DNP Internal
Event UR Value
Description point Deadband scaling
class enable range
address factor (ix=0)
Phase current Ia x In (CT) 0 2 1 1 0...5000 100

Phase current Ib x In (CT) 1 2 1 1 0...5000 100

Phase current Ic x In (CT) 2 2 1 1 0...5000 100

Ground-fault current x In 3 2 1 1 0...800 10

(CT)
Phase discontinuity, I(unbal) 4 2 1 1 0...100 10
Thermal level 5 2 1 1 0...106 1
One-minute demand value 6 2 1 1 0...5000 100
Demand value during the 7 2 1 1 0...5000 100
specified time range
Maximum one-minute 8 2 1 1 0...5000 100
demand value during the
specified time range

91

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

Table 4.1.16.3-3 Counters

DNP point Event UR Value
Description Deadband
address class enable range
Number of pickups of element 51P 0 3 1 1 0...999
Number of pickups of element 50P-1 1 3 1 1 0...999
Number of pickups of element 50P-2 2 3 1 1 0...999
Number of pickups of element 51N 3 3 1 1 0...999
Number of pickups of element 50N 4 3 1 1 0...999
Number of pickups of element 46 5 3 1 1 0...999
Number of trips of element 51P 6 3 1 1 0...65535
Number of trips of element 50P-1 7 3 1 1 0...65535
Number of trips of element 50P-2 8 3 1 1 0...65535
Number of trips of other elements 9 3 1 1 0...65535
Number of AR shots (shot 1) initiated 10 3 1 1 0...255
by the trip signal from element 50P-1
Number of AR shots (shot 1) initiated 11 3 1 1 0...255
by the digital input signal
Number of AR shots (shot 1) initiated 12 3 1 1 0...255
by the pickup or trip signal from
element 51P
Number of AR shots (shot 1) initiated 13 3 1 1 0...255
by the pickup or trip signal from
element 51N
Number of AR shots (shot 2) initiated 14 3 1 1 0...255
by the trip signal from element 50P-1
Number of AR shots (shot 2) initiated 15 3 1 1 0...255
by the digital input signal
Number of AR shots (shot 2) initiated 16 3 1 1 0...255
by the pickup or trip signal from
element 51P
Number of AR shots (shot 2) initiated 17 3 1 1 0...255
by the pickup or trip signal from
element 51N
Number of AR shots (shot 3) initiated 18 3 1 1 0...255
by the trip signal from element 50P-1
Number of AR shots (shot 3) initiated 19 3 1 1 0...255
by the digital input signal
Number of AR shots (shot 3) initiated 20 3 1 1 0...255
by the pickup or trip signal from
element 51P
Number of AR shots (shot 3) initiated 21 3 1 1 0...255
by the pickup or trip signal from
element 51N

92

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

4.1.16.4. DNP 3.0 device profile of REF 610

DNP V3.00
DEVICE PROFILE DOCUMENT
Vendor Name: ABB Oy, Distribution Automation
Device Name: REF 610
Highest DNP Level Supported Device Function
For Requests lb Slave
For Responses lb
Notable objects, functions, and/or qualifiers supported in addition to the Highest DNP Levels
Supported (the complete list is described in the attached table):
Additions to level 2 are marked as shaded in the implementation table.
Maximum Data Link Frame Size (octets) Maximum Application Fragment Size (octets)
Transmitted 292 Transmitted 2048
Received 292 Received 2048
Maximum Data Link Re-tries: Maximum Application Layer Re-tries:
Configurable, range from 0 to 255 with Configurable, range from 0 to 255 with
primary data link layer retransmission count application layer retransmission count
Requires Data Link Layer Confirmation:
Configurable, with confirmation type selector, default NO ACK
Requires Application Layer Confirmation
Configurable with confirmation type selector when reporting Event Data
(Slave devices only)
Always after response to reset request

Always when sending multi-fragment responses (Slave devices only)

Configurable, with confirmation type selector

Timeouts while waiting for
Data Link Confirm Configurable with primary data link layer
timeout, not relevant when NO ACK
Complete Appl. Fragment No, multi-fragment application frames not
supported
Application Confirm Configurable with application layer timeout
Complete Appl. Response No, not relevant in slave
Sends/Executes Control Operations
WRITE Binary Outputs
Never
SELECT/OPERATE
Never
DIRECT OPERATE
Never
DIRECT OPERATE - NO ACK
Never
Count
Never
Code
Never
Trip/Close
Never
Pulse On
Never
Queue
Never
Clear Queue
Never

93

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

FILL OUT THE FOLLOWING ITEMS FOR SLAVE DEVICES ONLY

Reports Digital Input Change Events when Reports time-tagged Digital Input Change
no specific variation requested Events when no specific variation requested
Never Never

Only time-tagged Binary Input Change With

Time
Only non-time-tagged Binary Input Change With
Relative Time
Configurable to send both, one or the Configurable, depends on
other (depends on default variation) objects basic variation
(variation used at
initialization)
Sends Unsolicited Responses Sends Static Data in Unsolicited Responses
Never Never

Configurable When Device Restarts

Only certain objects When Status Flags Change

Sometimes (attach explanation)

ENABLE/DISABLE UNSOLICITED
Function codes supported
No other options are permitted.
Default Counter Object/Variation Counters Roll Over at
No Counters Reported No Counters Reported

Configurable, default object and variation Configurable (attach explanation)

Default Object 20 16 Bits (Counters 6...9)

Default Variation 2
Point-by-point list attached 32 Bits, but roll-over bits not used

Other value: 999 (Counters 0...5) and

255 (Counters 10...21)
Point-by-point list attached
Sends Multi-Fragment Responses
Yes No

Table 4.1.16.4-1 Supported function codes

Code Function Description Supported
Transfer Function Codes
0 Confirm Message fragment confirmation Yes
No response
1 Read Request objects from outstation Yes
Respond with requested objects
2 Write Store specified objects to outstation Yes
Respond with status of operation
Control Function Codes
3 Select Select output point of outstation No
Respond with status of control point

94

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

Table 4.1.16.4-1 Supported function codes

Code Function Description Supported
4 Operate Set previously selected output No
Respond with status of control point
5 Direct operate Set output directly No
Respond with status of control point
6 Direct operate NO ACK Set output directly No
No response
Freeze Function Codes
7 Immediate Freeze Copy specified objects to freeze buffer Yes
Respond with status of operation
8 Immediate Freeze NO ACK Copy specified objects to freeze buffer Yes
No response
9 Freeze and Clear Copy specified objects to freeze buffer Yes 1)
and clear objects
Respond with status of operation
10 Freeze and Clear NO ACK Copy specified objects to freeze buffer Yes 1)
and clear objects
No response
11 Freeze with time Copy specified objects to freeze buffer No
at specified time
Respond with status of operation
12 Freeze with time NO ACK Copy specified objects to freeze buffer No
at specified time
No response
Application Control Function Codes
13 Cold Restart Perform desired reset sequence Yes
Respond with a time object
14 Warm Restart Perform desired partial reset operation Yes
Respond with a time object
15 Initialize Data to Defaults Initialize the specified data to default No
Respond with status of operation
16 Initialize Application Set the specified application ready to No
be run
Respond with status of operation
17 Pickup Application Pickup the specified application to run Yes
Respond with status of operation
18 Stop Application Stop the specified application to run Yes
Respond with status of operation
Configuration Function Codes
19 Save configuration Save configuration No
Respond with status of operation
20 Enable Unsolicited Messages Enable Unsolicited Messages Yes
Respond with status of operation
21 Disable Unsolicited Disable Unsolicited Messages Yes
Messages Respond with status of operation
22 Assign Class Assign specified objects to a class Yes
Respond with status of operation
Time Synchronization Function Codes
23 Delay Measurement Perform propagation delay Yes
measurement

95

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

Table 4.1.16.4-1 Supported function codes

Code Function Description Supported
Response Function Codes
0 Confirm Message fragment confirmation Yes
129 Response Response to request message Yes
130 Unsolicited Message Spontaneous message without Yes
request
1)
Counters of REF 610 can not be cleared using the DNP 3.0 protocol.

Table 4.1.16.4-2 Supported objects

REQUEST RESPONSE
OBJECT
(slave must parse) (master must parse)

Function Qualifier Function Qualifier

Object
Variation Description Codes Codes Codes Codes
group
(dec) (hex) (dec) (hex)
1 0 Binary Input, all variations 1, 20, 00, 01, 129 00, 01,
21, 22 06, 07, 17, 28
08,
17,28
1 1 Binary Input 1, 20, 00, 01, 129 00, 01,
21, 22 06, 07, 17, 28
08,
17,28
1 2 Binary Input with Status 1, 20, 00, 01, 129 00, 01,
21, 22 06, 07, 17, 28
08,
17,28
2 0 Binary Input Change, all 1 06, 07,
variations 08
2 1 Binary Input Change without 1 06, 07, 129, 17, 28
Time 08 130
2 2 Binary Input Change with Time 1 06, 07, 129, 17, 28
08 130
2 3 Binary Input Change with
Relative Time
10 0 Binary Output, all variations
10 1 Binary Output
10 2 Binary Output with Status
12 0 Control Block, all variations
12 1 Control Relay Output Block
12 2 Pattern Control Block
12 3 Pattern Mask
20 0 Binary Counter, all variations 1, 7, 8, 00, 01, 129 00, 01,
20, 21, 06, 07, 17, 28
22 08,
17,28
20 1 32-Bit Binary Counter 1, 7, 8, 00, 01, 129 00, 01,
20, 21, 06, 07, 17, 28
22 08,
17,28
20 2 16-Bit Binary Counter 1, 7, 8, 00, 01, 129 00, 01,
20, 21, 06, 07, 17, 28
22 08,
17,28
20 3 32-Bit Delta Counter
20 4 16-Bit Delta Counter

96

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

Table 4.1.16.4-2 Supported objects

REQUEST RESPONSE
OBJECT
(slave must parse) (master must parse)

Function Qualifier Function Qualifier

Object
Variation Description Codes Codes Codes Codes
group
(dec) (hex) (dec) (hex)
20 5 32-Bit Binary Counter without
Flag
20 6 16-Bit Binary Counter without
Flag
20 7 32-Bit Delta Counter without
Flag
20 8 16-Bit Delta Counter without
Flag
21 0 Frozen Counter, all variations 1 00, 01, 129 00, 01,
06, 07, 17, 28
08,
17,28
21 1 32-Bit Frozen Counter 1 00, 01, 129 00, 01,
06, 07, 17, 28
08,
17,28
21 2 16-Bit Frozen Counter 1 00, 01, 129 00, 01,
06, 07, 17, 28
08,
17,28
21 3 32-Bit Frozen Delta Counter
21 4 16-Bit Frozen Delta Counter
21 5 32-Bit Frozen Counter with Time 1 00, 01, 129 00, 01,
of Freeze 06, 07, 17, 28
08,
17,28
21 6 16-Bit Frozen Counter with Time 1 00, 01, 129 00, 01,
of Freeze 06, 07, 17, 28
08,
17,28
21 7 32-Bit Frozen Delta Counter with
Time of Freeze
21 8 16-Bit Frozen Delta Counter with
Time of Freeze
21 9 32-Bit Frozen Counter without
Flag
21 10 16-Bit Frozen Counter without
Flag
21 11 32-Bit Frozen Delta Counter
without Flag
21 12 16-Bit Frozen Delta Counter
without Flag
22 0 Counter Change Event, all 1 06, 07, 129, 17, 28
variations 08 130
22 1 32-Bit Counter Change Event 1 06, 07, 129, 17, 28
without Time 08 130
22 2 16-Bit Counter Change Event 1 06, 07, 129, 17, 28
without Time 08 130
22 3 32-Bit Delta Counter Change
Event without Time
22 4 16-Bit Delta Counter Change
Event without Time

97

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

Table 4.1.16.4-2 Supported objects

REQUEST RESPONSE
OBJECT
(slave must parse) (master must parse)

Function Qualifier Function Qualifier

Object
Variation Description Codes Codes Codes Codes
group
(dec) (hex) (dec) (hex)
22 5 32-Bit Counter Change Event 1 06, 07, 129, 17, 28
with Time 08 130
22 6 16-Bit Counter Change Event 1 06, 07, 129, 17,28
with Time 08 130
22 7 32-Bit Delta Counter Change
Event with Time
22 8 16-Bit Delta Counter Change
Event with Time
23 0 Frozen Counter Event, all
variations
23 1 32-Bit Frozen Counter Event
without Time
23 2 16-Bit Frozen Counter Event
without Time
23 3 32-Bit Frozen Delta Counter
Event without Time
23 4 16-Bit Frozen Delta Counter
Event without Time
23 5 32-Bit Frozen Counter Event
with Time
23 6 16-Bit Frozen Counter Event
with Time
23 7 32-Bit Frozen Delta Counter
Event with Time
23 8 16-Bit Frozen Delta Counter
Event with Time
30 0 Analogue Input, all variations 1, 20, 00, 01, 129 00, 01,
21, 22 06, 07, 17, 28
08,
17,28
30 1 32-Bit Analogue Input 1, 20, 00, 01, 129 00, 01,
21, 22 06, 07, 17, 28
08,
17,28
30 2 16-Bit Analogue Input 1, 20, 00, 01, 129 00, 01,
21, 22 06, 07, 17, 28
08,
17,28
30 3 32-Bit Analogue Input without 1, 20, 00, 01, 129 00, 01,
Flag 21, 22 06, 07, 17, 28
08,
17,28
30 4 16-Bit Analogue Input without 1, 20, 00, 01, 129 00, 01,
Flag 21, 22 06, 07, 17, 28
08,
17,28
31 0 Frozen Analogue Input, all
variations
31 1 32-Bit Frozen Analogue Input
31 2 16-Bit Frozen Analogue Input
31 3 32-Bit Frozen Analogue Input
with Time of Freeze

98

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

Table 4.1.16.4-2 Supported objects

REQUEST RESPONSE
OBJECT
(slave must parse) (master must parse)

Function Qualifier Function Qualifier

Object
Variation Description Codes Codes Codes Codes
group
(dec) (hex) (dec) (hex)
31 4 16-Bit Frozen Analogue Input
with Time of Freeze
31 5 32-Bit Frozen Analogue Input
without Flag
31 6 16-Bit Frozen Analogue Input
without Flag
32 0 Analogue Change Event, all 1 06, 07, 129, 17, 28
variations 08 130
32 1 32-Bit Analogue Change Event 1 06, 07, 129, 17, 28
without Time 08 130
32 2 16-Bit Analogue Change Event 1 06, 07, 129, 17, 28
without Time 08 130
32 3 32-Bit Analogue Change Event 1 06, 07, 129, 17, 28
with Time 08 130
32 4 16-Bit Analogue Change Event 1 06, 07, 129, 17, 28
with Time 08 130
33 0 Frozen Analogue Event, all
variations
33 1 32-Bit Frozen Analogue Event
without Time
33 2 16-Bit Frozen Analogue Event
without Time
33 3 32-Bit Frozen Analogue Event
with Time
33 4 16-Bit Frozen Analogue Event
with Time
40 0 Analogue Output Status, all
variations
40 1 32-Bit Analogue Output Status
40 2 16-Bit Analogue Output Status
41 0 Analogue Output Block, all
variations
41 1 32-Bit Analogue Output Block
41 2 16-Bit Analogue Output Block
50 0 Time and Date, all variations 1 06, 07, 129 17, 28
08
50 1 Time and Date 1 06, 07, 129 17, 28
(def) 08
50 1 Time and Date 2 07, 08 129
(def)
50 2 Time and Date with Interval
51 0 Time and Date CTO, all
variations
51 1 Time and Date CTO
51 2 Unsynchronized Time and Date
CTO
52 0 Time Delay, all variations
52 1 Time Delay Coarse
52 2 Time Delay Fine 23 07 129 07
60 0 All classes 1 06 129 28

99

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

Table 4.1.16.4-2 Supported objects

REQUEST RESPONSE
OBJECT
(slave must parse) (master must parse)

Function Qualifier Function Qualifier

Object
Variation Description Codes Codes Codes Codes
group
(dec) (hex) (dec) (hex)
60 1 Class 0 Data 1 06, 07, 129 17, 28
08
60 2 Class 1 Data 1 06, 07, 129 17, 28
08
60 3 Class 2 Data 1 06, 07, 129 17, 28
08
60 4 Class 3 Data 1 06, 07, 129 17, 28
08
70 1 File Identifier
80 1 Internal Targets 2 00 129
81 1 Storage Object
82 1 Device Profile
83 1 Private Registration Object
83 2 Private Registration Object
Descriptor
90 1 Application Identifier
100 1 Short Floating Point
100 2 Long Floating Point
100 3 Extended Floating Point
101 1 Small Packed Binary-Coded
Decimal
101 2 Medium Packed Binary-Coded
Decimal
101 3 Large Packed Binary-Coded
Decimal
No Object 13, 14

4.1.16.5. REF 610-specific DNP features

Time synchronization
If time synchronization (minute-pulse or second-pulse) of the relay’s real-time clock
is realized via a digital input, the following applies to the DNP interface of REF 610:
• Depending on the pulse type, either the date-to-minute or the date-to-second
information of the DNP time synchronization message will be used.
• REF 610 will send only one request for time synchronization to the DNP master,
which is at power up.

100

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

Unsolicited reporting pick up

Due to implementation differences in DNP master devices, the following alternative
unsolicited reporting (SPA parameter 503V24) pick ups are available in REF 610:
• 1 = Unsolicited reporting picks up immediately, without permission from the
master.
• 2 = REF 610 will send an empty unsolicited response message when
communication begins, which the master will confirm. After this, REF 610 will
pickup to send unsolicited responses.
• 3 = REF 610 will send an empty unsolicited response message when
communication begins, which the master will confirm. After this, the master will
enable unsolicited reporting for certain or all classes using function 20. Classes
which are not enabled remain disabled.
Note!
Only the last alternative is compliant with the DNP 3.0 standard.
Event handling
The maximum capacity of the DNP event buffer is 100 events. When unsolicited
reporting has been enabled (SPA parameter 503V24), the event reporting will use
the following SPA parameters, called send throttle parameters:

503V18 Class 1 Event delay

503V19 Class 1 Event count
503V20 Class 2 Event delay
503V21 Class 2 Event count
503V22 Class 3 Event delay
503V23 Class 3 Event count

Example (class 1)
The events will be reported when the event delay (SPA parameter 503V18) has
elapsed or the defined amount of events (SPA parameter 503V19) have been
generated for class 1.
If send throttles are not desired, the event delay should be set to 0 and the event count
to 1. In this case, the class events will be sent to the host immediately as they occur.
Event buffer overflow
DNP 3.0 event buffer overflow is indicated with the internal target IIN2.3, as
defined by the standard. IIN2.3 can also indicate event buffer overflow in the
internal communication between the DNP3.0 module and the main CPU module of
REF 610. In this case, REF 610 will automatically activate and reset the IIN2.3 bit.
As events have been lost in both cases, the DNP 3.0 master should perform an
integrity scan after the IIN2.3 bit has been reset.
DNP counters and frozen counters
DNP counters in use have a corresponding frozen counter. The frozen counters in
object group 21 have the same DNP point index as the ordinary DNP counters.
Further, frozen counters can only be read as static objects, and frozen counter events
(object group 23) are not supported.

101

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

Collision avoidance and detection

REF 610 supports both collision avoidance and detection. Collision detection can be
enabled or disabled with SPA parameter 503V235.
Collision avoidance occurs before message transmission. When preparing to
transmit and the link is busy, REF 610 will first wait until the link becomes idle.
After this, a backoff time will pickup. When the backoff time elapses, REF 610 will
check the link again. If not busy, REF 610 will pickup the transmission. The backoff
time is calculated as follows:
backoff time = silent interval + random delay
The silent interval is set with SPA parameter 503V232 and the maximum random
delay with SPA parameters 503V233 (the width of a single time slot in milliseconds)
and 503V234 (the maximum number of time slots). By setting the time-slot width to
10 milliseconds and the maximum number of time slots to 10, for instance, the
maximum random delay will be 100 milliseconds.
Note!
In a network consisting of several slaves, the priority between the devices are
defined with SPA parameters 503V233 and 503V234. A device with shorter silent
interval and maximum random delay has higher sending priority than a device with
longer silent interval and maximum random delay.
Collision detection is always active during transmission (provided that it has been
enabled). While sending a message, REF 610 supervises collisions on the link. If a
collision is detected, the transmission will be immediately cancelled. After this, REF
610 will try to transmit the message again, using collision avoidance before sending
the message.
Scaling DNP analogue values
The DNP analogue values can be scaled using either an internal (fixed) or a
user-defined scaling factor. If the scaling factor index for a certain analogue value is
set to 0, the internal scaling factor will be used. If set to 1...5, the user-defined scaling
factor of the corresponding scaling factor parameter, SPA parameter
503V(100+index), will be used:

503V101 Scaling factor 1

503V102 Scaling factor 2
503V103 Scaling factor 3
503V104 Scaling factor 4
503V105 Scaling factor 5

Example

Phase current la 0.00...50.0 x In (CT)

Internal scaling factor 100
Default DNP range 0...5000
To show the analogue value in primary units, and if In (CT) = 300 A and the
accuracy of the analogue value = 1 A:
1. Take any unused scaling factor and set it to 300.
2. Set the scaling index pointer of the analogue value to point at the scaling factor.

102

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

3. The value range will now be 0.00 x 300....50.0 x 300 = 0...15000 A.

DNP analogue values deadband
The deadband is always defined in units of the original value when scaled using the
internal (fixed) scaling factor, irrespective of whether the internal scaling factor is
used for value presentation or not.
Example
For a deadband of 2% In (CT) when the internal scaling factor is 100, the deadband
value is set as follows: 0.02 x 100 = 2. If the scaling factor is set to 300 A, the scaled
deadband is 300 A x 0.02 = 6 A.

4.1.17. SPA bus communication protocol parameters

Altering parameter values via serial communication requires the use of the SPA
password in some cases. The password is a user-defined number within the range
1...999, the default value being 1. SPA parameters are found on channels 0...5,
503...504, 507 and 601...603.
To enter the setting mode, enter the password into parameter V160. To exit the
setting mode, enter the same password into parameter V161. The password
protection is also reactivated in case of loss of auxiliary voltage.
The HMI password can be changed with parameter V162, but it is not possible to
read the password via this parameter.
Abbreviations used in the following tables:
• R = readable data
• W = writeable data
• P = password protected writeable data
Settings
Table 4.1.17-1 Settings
Actual Group/ Group/
Variable settings (R), Channel 1 Channel 2 Setting range
channel 0 (R, W, P) (R, W, P)
Pickup value of element 51P S1 1S1 2S1 0.30...5.00 x In (CT)
Operate time of element S2 1S2 2S2 0.05...300 s
51P TDLY
Time/current characteristic S3 1S3 2S3 0...8
for element 51P
Time multiplier 51P TD IEC S4 1S4 2S4 0.05...1.00
Time multiplier 51P TD ANSI S5 1S5 2S5 1.0...15.0
Resetting time of element S6 1S6 2S6 0.05...2.50 s
51P RSET
Pickup value of element S7 1) 1S7 2S7 0.50...35.0 x In (CT)
50P-1
Operate time of element S8 1S8 2S8 0.04...300 s
51P-1 TDLY
Pickup value of element S9 1) 1S9 2S9 0.50...35.0 x In (CT)
50P-2

103

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

Table 4.1.17-1 Settings

Actual Group/ Group/
Variable settings (R), Channel 1 Channel 2 Setting range
channel 0 (R, W, P) (R, W, P)
Operate time of element S10 1S10 2S10 0.04...30.0 s
50P-2 TDLY
Pickup value of element 51N S11 1S11 2S11 1.0...100% In (CT)
Operate time of element S12 1S12 2S12 0.05...300 s
51N TDLY
Time/current characteristic S13 1S13 2S13 0...8
for element 51N
Time multiplier 51N TD IEC S14 1S14 2S14 0.05...1.00 s
Time multiplier 51N TD ANSI S15 1S15 2S15 1.0…15.0
Resetting time of element S16 1S16 2S16 0.05...2.50
51N RSET
Pickup value of element 50N S17 1) 1S17 2S17 5.0...400% In (CT)
Operate time of element S18 1S18 2S18 0.05...300 s
50N TDLY
Pickup value of element 46 S19 1) 1S19 2S19 10...100%
Operate time of element S20 1S20 2S20 1...300 s
46 TDLY
Full load current S21 1) 1S21 2S21 0.30...1.50 x In (CT)
Time constant of element 49 S22 1S22 2S22 1...200 min
Alarm level of element 49 S23 1) 1S23 2S23 50...100% 49 trip
Operate time of Trip Fail S24 1S24 2S24 0.10...60.0 s
Number of AR shots S25 1S25 2S25 0 = AR is not in use
1 = shot 1
2 = shot 1 and 2
3 = shot 1, 2 and 3
Current limit Arc 50P of S26 1) 2) 1S26 2S26 0.50...35.0 x In (CT)
element ARC
Current limit Arc 50N of S27 1) 2) 1S27 2S27 5.0...400% In (CT)
element ARC
Checksum, SGF 1 S61 1S61 2S61 0...255
Checksum, SGF 2 S62 1S62 2S62 0...127
Checksum, SGF 3 S63 1S63 2S63 0...127
Checksum, SGF 4 S64 1S64 2S64 0...63
Checksum, SGF 5 S65 1S65 2S65 0...255
Checksum, SGB 1 S71 1S71 2S71 0...1048575
Checksum, SGB 2 S72 1S72 2S72 0...1048575
Checksum, SGB 3 S73 3) 1S73 2S73 0...1048575
Checksum, SGB 4 S74 3) 1S74 2S74 0...1048575
Checksum, SGB 5 S75 3) 1S75 2S75 0...1048575
Checksum, SGR 1 S81 1S81 2S81 0...8388607
Checksum, SGR 2 S82 1S82 2S82 0...8388607
Checksum, SGR 3 S83 1S83 2S83 0...8388607
Checksum, SGR 4 S84 1S84 2S84 0...8388607
Checksum, SGR 5 S85 1S85 2S85 0...8388607
Checksum, SGR 6 S86 3) 1S86 2S86 0...8388607
Checksum, SGR 7 S87 3) 1S87 2S87 0...8388607

104

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

Table 4.1.17-1 Settings

Actual Group/ Group/
Variable settings (R), Channel 1 Channel 2 Setting range
channel 0 (R, W, P) (R, W, P)
Checksum, SGR 8 S88 3) 1S88 2S88 0...8388607
Checksum, SGL 1 S91 1S91 2S91 0...2097151
Checksum, SGL 2 S92 1S92 2S92 0...2097151
Checksum, SGL 3 S93 1S93 2S93 0...2097151
Checksum, SGL 4 S94 1S94 2S94 0...2097151
Checksum, SGL 5 S95 1S95 2S95 0...2097151
Checksum, SGL 6 S96 1S96 2S96 0...2097151
Checksum, SGL 7 S97 1S97 2S97 0...2097151
Checksum, SGL 8 S98 1S98 2S98 0...2097151
1)
If the protection element is out of operation, the number indicating the currently used value will be
displaced by “999” when the parameter is read via the SPA bus and by dashes on the LCD.
2)
If the optional/O module has not been installed, a dash will be shown on the LCD and “999” when the
parameter is read via the SPA bus.
3)
If the optional/O module has not been installed, a dash will be shown on the LCD and “9999999” when
the parameter is read via the SPA bus.

Auto-reclose parameters
Table 4.1.17-2 Settings
Parameter
Description (R, W, P), Value
channel 0
CB Closing time V121 0.1...10 s
Pickup delay of element 51P V122 0...300 s
Pickup delay of element 51N V123 0...300 s
Reset time V124 3...300 s
Cutout time V125 0.1...300 s
Open time of shot 1 V126 0.1...300 s
Open time of shot 2 V127 0.1...300 s
Open time of shot 3 V128 0.1...300 s
SG1 V129 0...255
SG2 V130 0...1023
SG3 V131 0...31

The AR function can be activated either via the HMI or with SPA parameter S25 by
setting the number of auto-reclose shots to 1, 2 or 3.

105

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

Recorded data
Parameter V1 shows the element which has caused the trip, parameter V2 the trip
target code, parameters V3...V8 show the number of pickups of the protection
elements, parameters V9...V12 the number of trips of the protection elements, and
parameters V13...V24 the number of initiated auto-reclose shots.

Table 4.1.17-3 Recorded data: Channel 0

Recorded data Parameter (R) Value
Element/phase which caused the trip V1 1=Ic(51P)
2=lb(51P)
4=la(51P)
8=51N
16=lc(50P-1)
32=lb(50P-1)
64=la(50P-1)
128=50N
256=lc(50P-2)
512=lb(50P-2)
1024=la(50P-2)
2048=46
4096=49
8192=external trip
16384=AR
32768=trip of element ARC (local)
65536=trip of element ARC
(remote)
Trip target code V2 0 = ---
1=pickup of element 51P
2=trip of element 51P
3=pickup of element 50P-1
4=trip of element 50P-1
5=pickup of element 50P-2
6=trip of element 50P-2
7=pickup of element 51N
8=trip of element 51N
9=pickup of element 50N
10=trip of element 50N
11=pickup of element 46
12=trip of element 46
13=alarm of element 49
14=trip of element 49
15=external trip
16=definite trip alarm
17=CB reclosing failed
18=AR shot due
19=AR lockout
20=trip of element ARC
21=CBFAIL
Number of pickups of element 51P V3 0...999
Number of pickups of element 50P-1 V4 0...999
Number of pickups of element 50P-2 V5 0...999
Number of pickups of element 51N V6 0...999
Number of pickups of element 50N V7 0...999
Number of pickups of element 46 V8 0...999
Number of trips of element 50P-1 V10 0...65535
Number of trips of element 50P-2 V11 0...65535

106

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

Table 4.1.17-3 Recorded data: Channel 0

Recorded data Parameter (R) Value
Number of trips of other elements V12 0...65535
Number of AR shots (shot 1) initiated V13 0...255
by the trip signal from element 50P-1
Number of AR shots (shot 1) initiated V14 0...255
by the digital input signal
Number of AR shots (shot 1) initiated V15 0...255
by the pickup or trip signal from
element 51P
Number of AR shots (shot 1) initiated V16 0...255
by the pickup or trip signal from
element 51N
Number of AR shots (shot 2) initiated V17 0...255
by the trip signal from element 50P-1
Number of AR shots (shot 2) initiated V18 0...255
by the digital input signal
Number of AR shots (shot 2) initiated V19 0...255
by the pickup or trip signal from
element 51P
Number of AR shots (shot 2) initiated V20 0...255
by the pickup or trip signal from
element 51N
Number of AR shots (shot 3) initiated V21 0...255
by the trip signal from element 50P-1
Number of AR shots (shot 3) initiated V22 0...255
by the digital input signal
Number of AR shots (shot 3) initiated V23 0...255
by the pickup or trip signal from
element 51P
Number of AR shots (shot 3) initiated V24 0...255
by the pickup or trip signal from
element 51N
The last five recorded values can be read with parameters V1...V23 on channels
1...5. Event n denotes the last recorded value, n-1 the next one, and so forth.

Table 4.1.17-4 Recorded data: Channels 1...5

Event (R)

Recorded data n-3 n-4 Value

n n-1 n-2
Channel Channel
Channel 1 Channel 2 Channel 3
4 5
Phase current la 1V1 2V1 3V1 4V1 5V1 0...50 x In (CT)
Phase current lb 1V2 2V2 3V2 4V2 5V2 0...50 x In (CT)
Phase current lc 1V3 2V3 3V3 4V3 5V3 0...50 x In (CT)
Ground-fault 1V4 2V4 3V4 4V4 5V4 0...800% In (CT)
current
Phase 1V5 2V5 3V5 4V5 5V5 0...100%
discontinuity
Thermal level at 1V6 2V6 3V6 4V6 5V6 0...106% 1)
pickup
Thermal level at 1V7 2V7 3V7 4V7 5V7 0...106% 1)
trip

107

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

Table 4.1.17-4 Recorded data: Channels 1...5

Event (R)

Recorded data n-3 n-4 Value

n n-1 n-2
Channel Channel
Channel 1 Channel 2 Channel 3
4 5
Maximum pick- 1V8 2V8 3V8 4V8 5V8 0...50 x In (CT)
up phase current
la
Maximum pick- 1V9 2V9 3V9 4V9 5V9 0...50 x In (CT)
up phase current
lb
Maximum pick- 1V10 2V10 3V10 4V10 5V10 0...50 x In (CT)
up phase current
lc
Maximum pick- 1V11 2V11 3V11 4V11 5V11 0...800%
up ground-fault
current
Pickup duration 1V12 2V12 3V12 4V12 5V12 0...100%
of element 51P
Pickup duration 1V13 2V13 3V13 4V13 5V13 0...100%
of element 50P-
1
Pickup duration 1V14 2V14 3V14 4V14 5V14 0...100%
of element 50P-
2
Pickup duration 1V15 2V15 3V15 4V15 5V15 0...100%
of element 51N
Pickup duration 1V16 2V16 3V16 4V16 5V16 0...100%
of element 50N
Pickup duration 1V17 2V17 3V17 4V17 5V17 0...100%
of element 46
Pickup duration 1V18 2V18 3V18 4V18 5V18 0/100%
of external trip
Trip number of 1V19 2V19 3V19 4V19 5V19 0...255
AR sequence
Pickup duration 1V20 2V20 3V20 4V20 5V20 0/100%
of element ARC
(local)
Pickup duration 1V21 2V21 3V21 4V21 5V21 0/100%
of element ARC
(remote)
Time stamp of 1V22 2V22 3V22 4V22 5V22 YY-MM-DD
the recorded
data, date
Time stamp of 1V23 2V23 3V23 4V23 5V23 HH.MM;
the recorded SS.sss
data, time
1)
If the thermal protection has been set out of operation (SGF3/5), dashes will be shown on the LCD
and “999” when the parameter is read via the SPA bus.

108

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

Disturbance recorder
Table 4.1.17-5 Parameters for the disturbance recorder
Parameter
Description R, W Value
(channel 0)
Remote triggering M1 2) W 1
Clear recorder memory M2 W 1
Sampling rate M15 3) R, W 800/960 Hz
400/480 Hz
50/60 Hz
Station identification/unit number M18 R, W 0...9999
Rated frequency M19 R 50 or 60 Hz
Name of the feeder M20 R, W Max 16 characters
Digital channel texts M40...M47 R
Analogue channel texts M60...M63 R
Analogue channel conversion factor and M80 1) 4) R, W Factor 0...65535, unit
unit for Ia, Ib and Ic M81 and (A, kA), e.g. 10,kA
M82 R
Analogue channel conversion factor and M83 1) R, W Factor 0...65535, unit
unit for the ground-fault current (A, kA), e.g. 10,kA
Internal trigger signals' checksum V236 R, W 0...16383
Internal trigger signal's edge V237 R, W 0...16383
Checksum of internal signal storing mask V238 3) R, W 0...16383
Post-triggering recording length V240 R, W 0...100%
External trigger signal's checksum V241 R, W 0...31
External trigger signal's edge V242 R, W 0...31
Checksum of external signal storing mask V243 3) R, W 0...31
Triggering state, clearing and restart V246 R, W R:
0 = recorder not
triggered
1 = recorder triggered
and recording stored
in the memory
W:
0 = clear recorder
memory
2 = download restart;
sets the first
information and the
time stamp for
triggering ready to be
read
4 = manual triggering
1)
The disturbance recorder requires this parameter to be set. The conversion factor is the
transformation ratio multiplied by the rated current of the relay. If this parameter has been given the
value 0, dashes will be shown on the LCD instead of the primary values and the recorded data will be
redundant.
2)
M1 can be used for broadcast triggering by using the unit address “900”.
3)
Parameters can be written if the recorder has not been triggered.
4)
This value is copied to parameters M81 and M82.

109

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

Table 4.1.17-6 Disturbance recorder internal triggering and storing

Default value of Default value of Default value of
Weighting triggering edge, storing mask,
Event triggering
factor
mask, V236 V237 1) V238
Pickup of element 51P 1 0 0 1
Trip of element 51P 2 1 0 1
Pickup of element 50P-1 4 0 0 1
Trip of element 50P-1 8 1 0 1
Pickup of element 50P-2 16 0 0 0
Trip of element 50P-2 32 1 0 1
Pickup of element 51N 64 0 0 1
Trip of element 51N 128 1 0 1
Pickup of element 50N 256 0 0 0
Trip of element 50N 512 1 0 1
Pickup of element 46 1024 0 0 0
Trip of element 46 2048 0 0 0
Alarm of element 49 4096 0 0 0
Trip of element 49 8192 0 0 0
Checksum 682 0 751
1) 0 = rising edge, 1 = falling edge.

Table 4.1.17-7 Disturbance recorder external triggering and storing

Default value of Default value of Default value of
Weighting triggering edge, storing mask,
Event triggering
factor
mask, V241 V242 1) V243
DI1 1 0 0 0
DI2 2 0 0 0
DI3 4 0 0 0
DI4 8 0 0 0
DI5 16 0 0 0
Checksum 0 0 0
1)
0 = rising edge, 1 = falling edge.

Control parameters
Table 4.1.17-8 Control parameters
Description Parameter R, W, P Value
Reading of the event buffer L R Time, channel number and
event code
Re-reading of the event buffer B R Time, channel number and
event code
Reading of relay state data C R 0 = normal state
1 = the relay has been
subject to an automatic
reset
2 = overflow of the event
buffer
3 = both 1 and 2

110

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

Table 4.1.17-8 Control parameters

Description Parameter R, W, P Value
Resetting of relay state data C W 0 = reset E50 and E51
1 = reset only E50
2 = reset only E51
4 = reset all events
including E51 except for
E50
Time reading and setting T R, W SS.sss
Date and time reading and setting D R, W YY-MM-DD HH.MM;SS.sss
Type designation of the relay F R REF 610
Unlatching output contacts V101 W 1 = unlatch
Clearing targets and memorized V102 W 1 = clear and unlatch
values and unlatching contacts
(master reset)
Resetting of trip lockout V103 W 1 = reset
Rated frequency V104 R, W (P) 50 or 60 Hz
Time setting range for demand values V105 R, W 0...999 min
in minutes
Non-volatile memory settings V106 R, W 0...31
Time setting for disabling new trip V108 R, W (P) 0...999 min
targets on the LCD
Testing the self-supervision V109 W (P) 1 = the self-supervision
output contact is activated
and the READY target LED
pickups to blink
0 = normal operation
LED test for pickup and trip targets V110 W (P) 0 = pickup and trip LEDs off
1 = trip LED on, pickup
LED off
2 = pickup LED on, trip
LED off
3 = pickup and trip LEDs
on
LED test for programmable LEDs V111 W (P) 0...255
Trip-circuit supervision V113 R, W 0 = not in use
1 = in use
Remote control of setting group V150 R, W 0 = setting group 1
1 = setting group 2
Entering the SPA password for V160 W 1...999
settings
Changing the SPA password or V161 W (P) 1...999
reinstating the password protection
Changing the HMI password V162 W 1...999
Clearing trip counters or AR counter V166 W (P) 1= clear trip counters
2= clear AR counters
Restoring factory settings V167 W (P) 2 = restore factory settings
for CPU
3 = restore factory settings
for DNP
Warning code V168 R 0...65535 1)
IRF code V169 R 0...255 1)
Unit address of the relay V200 R, W 1...254
Data transfer rate (SPA), kbps V201 R, W 9.6/4.8

111

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

Table 4.1.17-8 Control parameters

Description Parameter R, W, P Value
Rear communication V202 W 1 = rear connector
activated
Rear communication protocol V203 3) R, W 0 = SPA
1 = IEC_103
2 = Modbus RTU
3 = Modbus ASCII
4 = DNP 3.0 (read-only)
Connection type V204 R, W 0 = loop
1 = star
Line-idle state V205 R, W 0 = light off
1 = light on
Optional communication module V206 R, W (P) 0 = not in use
1 = in use 2)
CPU software number V227 R 1MRS118512
CPU software revision V228 R A...Z
CPU build number V229 R XXX
Language Set V226 R 00..99
DNP protocol name 2V226 R DNP 3.0
DNP software number 2V227 R 1MRS118531
DNP software revision 2V228 R A...Z
DNP build number 2V229 R XXX
Relay serial number V230 R BAxxxxxx
CPU serial number V231 R ACxxxxxx
DNP serial number V232 R AKxxxxxx
Test date V235 R YYMMDD
Date reading and setting V250 R, W YY-MM-DD
(RED 500 format)
Time reading and setting V251 R, W HH.MM;SS.sss
(RED 500 format)
1)
In case of a warning, the value 255 will be stored in V169. This will enable the master to continuously
read only V169.
2)
If the optional communication module has not been installed, a warning of a faulty communication
module will appear on the LCD together with the fault code.
3)
If the optional DNP 3.0 module has been installed, the DNP 3.0 communication protocol will be
automatically selected.

The measured currents can be read with parameters I1...I4, the calculated phase
discontinuity value with parameter I5, the status of light detection with parameter I6,
the CB position with parameter I7 and the status of the digital inputs with parameters
I8...I12.

Table 4.1.17-9 Inputs

Parameter (R),
Description Value
channel 0
Current measured on phase la I1 0...50 x In (CT)
Current measured on phase lb I2 0...50 x In (CT)
Current measured on phase lc I3 0...50 x In (CT)
Measured ground-fault current I4 0...800% In (CT)
Calculated phase discontinuity value I5 0...100%
Light detected (arc) I6 0/1

112

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

Table 4.1.17-9 Inputs

Parameter (R),
Description Value
channel 0
CB position I7 0 = undefined
1 = closed
2 = open
3 = undefined
DI1 status I8 0/1 1)
DI2 status I9 0/1 1)
DI3 status I10 0/1 1) 2)
DI4 status I11 0/1 1) 2)
DI5 status I12 0/1 1) 2)
1)
When the value is 1, the digital input is energized.
2)
If the optional I/O module has not been installed, a dash will be shown on the LCD and “9” when the
parameter is read via the SPA bus.

Each protection element has its internal output signal. These signals can be read with
parameters O1...O26 and the recorded functions with parameters O61...86. The state
of the output contacts can be read or changed with parameters O41...O49 and the
recorded functions read with parameters O101...O109.

Table 4.1.17-10Output signals

State of element Recorded
Status of the protection
(R), functions (R), Value
elements
channel 0 channel 0
Pickup of element 51P O1 O61 0/1
Trip of element 51P O2 O62 0/1
Pickup of element 50P-1 O3 O63 0/1
Trip of element 50P-1 O4 O64 0/1
Pickup of element 50P-2 O5 O65 0/1
Trip of element 50P-2 O6 O66 0/1
Pickup of element 51N O7 O67 0/1
Trip of element 51N O8 O68 0/1
Pickup of element 50N O9 O69 0/1
Trip of element 50N O10 O70 0/1
Pickup of element 46 O11 O71 0/1
Trip of element 46 O12 O72 0/1
Pickup of element 49 O13 O73 0/1
Alarm of element 49 O14 O74 0/1
Trip of element 49 O15 O75 0/1
External trip O16 O76 0/1
Trip lockout O17 O77 0/1
CBFAIL Trip O18 O78 0/1
Trip of element ARC O19 O79 0/1
Light signal output O20 O80 0/1
Open CB command O21 O81 0/1
Close CB command O22 O82 0/1
Definite trip alarm O23 O83 0/1
CB reclosing failed O24 O84 0/1
Shot due O25 O85 0/1
AR Lockout O26 O86 0/1

113

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

Table 4.1.17-11 Outputs

State of output Recorded
Operation of output
(R, W, P), functions (R), Value
contact
channel 0 channel 0
Output PO1 O41 O101 0/1
Output PO2 O42 O102 0/1
Output PO3 1) O43 O103 0/1 2)
Output SO1 O44 O104 0/1
Output SO2 O45 O105 0/1
Output PO3 O46 0/1 2)
(trip lockout) 3)
Output SO3 O47 O107 0/1 4)
Output SO4 O48 O108 0/1 4)
Output SO5 O49 O109 0/1 4)
Enabling activation of O51 - 0/1
output contacts PO1,
PO2, PO3, SO1, SO2,
SO3, SO4 and SO5 via
the SPA bus
1) State of output when the trip lockout function is not in use.
2) Either O43/O103 or O46 is to be used at a time.
3) State of output when the trip lockout function is in use.
4) If the optional I/O module has not been installed, a dash will be shown on the LCD and “9” when the
parameter is read via the SPA bus.

Note!
Parameters O41...O49 and O51 control the physical output contacts which can be
connected to circuit breakers, for instance.
Parameters for the IEC 60870-5-103 remote communication
protocol
Table 4.1.17-12Settings
Parameter
Description R, W, P Value
(channel 507)
Unit address of the relay 507V200 R, W 1...254
Data transfer rate (IEC_103), kbps 507V201 R, W 9.6/4.8

114

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

Parameters for the Modbus remote communication protocol

Table 4.1.17-13Settings
Parameter
Description R, W, P Value
(channel 504)
User-defined register 1 504V1 R, W 0...65535 1)
User-defined register 2 504V2 R, W 0...65535 1)
User-defined register 3 504V3 R, W 0...65535 1)
User-defined register 4 504V4 R, W 0...65535 1)
User-defined register 5 504V5 R, W 0...65535 1)
User-defined register 6 504V6 R, W 0...65535 1)
User-defined register 7 504V7 R, W 0...65535 1)
User-defined register 8 504V8 R, W 0...65535 1)
User-defined register 9 504V9 R, W 0...65535 1)
User-defined register 10 504V10 R, W 0...65535 1)
User-defined register 11 504V11 R, W 0...65535 1)
User-defined register 12 504V12 R, W 0...65535 1)
User-defined register 13 504V13 R, W 0...65535 1)
User-defined register 14 504V14 R, W 0...65535 1)
User-defined register 15 504V15 R, W 0...65535 1)
User-defined register 16 504V16 R, W 0...65535 1)
Unit address of the relay 504V200 R, W 1...254
Data transfer rate (Modbus), kbps 504V201 R, W 9.6/4.8/2.4/
1.2/0.3
Modbus link parity 504V220 R, W 0 = even
1 = odd
2 = no parity
CRC order of Modbus RTU link 504V221 R, W 0 = low/high
1 = high/low
1)
The default value is 0.

Parameters for the DNP 3.0 remote communication protocol

Table 4.1.17-14Settings
SPA
parameter
Description R, W Value range Default Explanation
(channel
503)
Unit address 503V1 R, W 0...65532 1 Address of REF 610 in the
DNP 3.0 network
Master address 503V2 R, W 0...65532 2 Address of the master
station (destination
address for unsolicited
responses)
Primary data link 503V3 R, W 0 = no data link 0 Used when REF 610
timeout timeout used sends data using service 3
1...65535 ms

115

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

Table 4.1.17-14Settings
SPA
parameter
Description R, W Value range Default Explanation
(channel
503)
Primary data link 503V4 R, W 0...255 0 Number of
layer retransmissions on data
retransmission link layer
count
Application layer 503V6 R, W 0...65535 ms 5000 Used when REF 610
confirmation sends messages with
timeout confirmation request
Application layer 503V7 R, W 0...255 0 Number of
retransmission retransmissions on the
count application layer when
REF 610 sends messages
with confirmation request
Confirmation on 503V9 R, W 0 = enabled only 0 Used to enforce inclusion
application layer for event of confirmation request in
messages all application messages
1 = enabled for (DNP 3.0 standard
all messages requires inclusion of
confirmation request in
event messages only)
Default variation 503V10 R, W 1...2 2
of binary input
objects
Default variation 503V11 R, W 1...2 2
of binary input
change event
objects
Default variation 503V15 R, W 1...4 2
of analogue input
objects
Default variation 503V16 R, W 1...4 2
of analogue input
change event
objects
Default variation 503V13 R, W 1...2 2
of counter objects
Default variation 503V14 R, W 1, 2, 5, 6 2
of counter change
event objects
Default variation 503V30 R, W 1, 2, 5, 6 2
of frozen counter
objects
Class 1 event 503V18 R, W 0...255 s 0
delay
Class 1 event 503V19 R, W 0...255 1
count
Class 2 event 503V20 R, W 0...255 s 0
delay
Class 2 event 503V21 R, W 0...255 1
count
Class 3 event 503V22 R, W 0...255 s 0
delay

116

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

Table 4.1.17-14Settings
SPA
parameter
Description R, W Value range Default Explanation
(channel
503)
Class 3 event 503V23 R, W 0...255 1
count
Unsolicited 503V24 R, W 0 = UR disabled 0 Refer to section
reporting mode 1 = immediate Unsolicited reporting pick
2 = empty UR up under section Protocol
3 = empty UR parameters of REF 610.
and enable UR
Scaling factor 1 503V101 R, W 0...4294967296 1
Scaling factor 2 503V102 R, W 0...4294967296 1
Scaling factor 3 503V103 R, W 0...4294967296 1
Scaling factor 4 503V104 R, W 0...4294967296 1
Scaling factor 5 503V105 R, W 0...4294967296 1
Baud rate 503V211 R, W 4.8/9.6/19.2/38.4 9.6
Number of stop 503V212 R, W 1...2 1
bits
Parity 503V230 R, W 0 = no parity 0
1 = odd
2 = even
Silent interval 503V232 R, W 0...65535 ms 20
Time slot width 503V233 R, W 0...255 ms 10
Number of time 503V234 R, W 0...255 8
slots
Collision 503V235 R, W 0 = disabled 0
detection enabled 1 = enabled
DNP module 503V168 R Bit coded
warning register 0 = OK
DNP module 503V169 R Bit coded
status register 0 = OK

Measurements
Table 4.1.17-15 Measured values
Parameter
Description R, W, P Value
(channel 0)
Thermal level V60 R, W (P) 0...106% 1) 3)
One-minute demand value V61 R 0...50 x In (CT)

Demand value during the specified time range V62 R 0...50 x In (CT)

Maximum one-minute demand value during V63 R 0...50 x In (CT)

the specified time range
1)
Changing the thermal level via serial communication will generate an event code.
2)
If the demand value is reset and the specified time has not elapsed, dashes will be shown on the LCD
and “999” when the parameter is read via the SPA bus.
3) If the thermal protection has been set out of operation, the parameter cannot be written to, and
dashes will be shown on the LCD and “999” when the thermal level is read via the SPA bus.

117

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

4.1.17.1. Operations Records

Special codes have been determined to represent certain events, such as pickup and
tripping of protection elements and different states of output signals.
The events are stored in the event buffer of the relay. The maximum capacity of the
buffer is 100 events. Under normal conditions the buffer is empty.
The contents of the buffer can be read using the L command, five events at a time.
Using the L command erases the previously read events from the buffer, with the
exception of events E50 and E51 which have to be reset using the C command.
Should a fault occur and reading fails, for example in data communication, the
events can be re-read using the B command. If needed, the B command can also be
repeated.
Events to be included in the event reporting are marked with the multiplier 1. The
event mask is formed by the sum of the weighting factors of all those events which
are to be included in event reporting.

Table 4.1.17.1-1 Event masks

Event mask Code Setting range Default setting
V155 E31...E34 0...15 1
1V155 1E1...1E12 0...4095 1365
1V156 1E13...1E24 0...4095 1365
1V157 1E25...1E42 0...262143 4180
2V155 2E1...2E16 0...65535 3
2V156 2E17...2E26 0...1023 0
3V155 3E1...3E12 0...4095 1023
3V156 3E13...3E22 0...1023 1008

Channel 0
Events always included in the event reporting:

Table 4.1.17.1-2 Event codes E1...E4 and E7

Channel Event Description
0 E1 IRF
0 E2 IRF disappeared
0 E3 Warning
0 E4 Warning disappeared
0 E7 The thermal level has been changed via serial
communication

Table 4.1.17.1-3 Event codes E50...E51

Channel Event Description
0 E50 Restart of relay
0 E51 Overflow of event buffer

118

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

Events possible to mask out:

Table 4.1.17.1-4 Event codes E31...E34

Weighting
Channel Event Description Default value
factor
0 E31 Disturbance recorder triggered 1 1
0 E32 Disturbance recorder cleared 2 0
0 E33 HMI password opened 4 0
0 E34 HMI password closed 8 0
Default value of event mask V155 1

Channel 1
Table 4.1.17.1-5 Event codes E1...E12
Weighting
Channel Event Description Default value
factor
1 E1 Pickup signal from element 51P activated 1 1
1 E2 Pickup signal from element 51P reset 2 0
1 E3 Trip signal from element 51P activated 4 1
1 E4 Trip signal from element 51P reset 8 0
1 E5 Pickup signal from element 50P-1 activated 16 1
1 E6 Pickup signal from element 50P-1 reset 32 0
1 E7 Trip signal from element 50P-1 activated 64 1
1 E8 Trip signal from element 50P-1 reset 128 0
1 E9 Pickup signal from element 50P-2 activated 256 1
1 E10 Pickup signal from element 50P-2 reset 512 0
1 E11 Trip signal from element 50P-2 activated 1024 1
1 E12 Trip signal from element 50P-2 reset 2048 0
Default value of event mask 1V155 1365

Table 4.1.17.1-6 Event codes E13...E24

Weighting
Channel Event Description Default value
factor
1 E13 Pickup signal from element 51N activated 1 1
1 E14 Pickup signal from element 51N reset 2 0
1 E15 Trip signal from element 51N activated 4 1
1 E16 Trip signal from element 51N reset 8 0
1 E17 Pickup signal from element 50N activated 16 1
1 E18 Pickup signal from element 50N reset 32 0
1 E19 Trip signal from element 50N activated 64 1
1 E20 Trip signal from element 50N reset 128 0
1 E21 Pickup signal from element 46 activated 256 1
1 E22 Pickup signal from element 46 reset 512 0
1 E23 Trip signal from element 46 activated 1024 1
1 E24 Trip signal from element 46 reset 2048 0
Default value of event mask 1V156 1365

119

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

Table 4.1.17.1-7 Event codes E25...E42

Weighting
Channel Event Description Default value
factor
1 E25 Pickup signal from element 49 activated 1 0
1 E26 Pickup signal from element 49 reset 2 0
1 E27 Alarm signal from element 49 activated 4 1
1 E28 Alarm signal from element 49 reset 8 0
1 E29 Trip signal from element 49 activated 16 1
1 E30 Trip signal from element 49 reset 32 0
1 E31 Trip signal from element ARC (light and 64 1
current) activated
1 E32 Trip signal from element ARC (light and 128 0
current) reset
1 E33 Trip signal from element ARC (DI and current) 256 0
activated
1 E34 Trip signal from element ARC (DI and current) 512 0
reset
1 E35 Light signal output activated 1024 0
1 E36 Light signal output reset 2048 0
1 E37 Trip lockout signal activated 4096 1
1 E38 Trip lockout signal reset 8192 0
1 E39 External trip signal activated 16384 0
1 E40 External trip signal reset 32768 0
1 E41 CBFAIL activated 65536 0
1 E42 CBFAIL reset 131072 0
Default value of event mask 1V157 4180

Channel 2
Table 4.1.17.1-8 Event codes E1...E16
Weighting
Channel Event Description Default value
factor
2 E1 PO1 activated 1 1
2 E2 PO1 reset 2 1
2 E3 PO2 activated 4 0
2 E4 PO2 reset 8 0
2 E5 PO3 activated 16 0
2 E6 PO3 reset 32 0
2 E7 SO1 activated 64 0
2 E8 SO1 reset 128 0
2 E9 SO2 activated 256 0
2 E10 SO2 reset 512 0
2 E11 SO3 activated 1024 0
2 E12 SO3 reset 2048 0
2 E13 SO4 activated 4096 0
2 E14 SO4 reset 8192 0
2 E15 SO5 activated 16384 0
2 E16 SO5 reset 32768 0
Default value of event mask 2V155 3

120

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

Table 4.1.17.1-9 Event codes E17...E26

Weighting
Channel Event Description Default value
factor
2 E17 DI1 activated 1 0
2 E18 DI1 deactivated 2 0
2 E19 DI2 activated 4 0
2 E20 DI2 deactivated 8 0
2 E21 DI3 activated 16 0
2 E22 DI3 deactivated 32 0
2 E23 DI4 activated 64 0
2 E24 DI4 deactivated 128 0
2 E25 DI5 activated 256 0
2 E26 DI5 deactivated 512 0
Default value of event mask 2V156 0

Channel 3
Table 4.1.17.1-10Event codes E1...E12
Weighting
Channel Event Description Default value
factor
3 E1 Shot 1 initiated 1 1
3 E2 Shot 1 ended 2 1
3 E3 Shot 2 Initiated 4 1
3 E4 Shot 2 ended 8 1
3 E5 Shot 3 initiated 16 1
3 E6 Shot 3 ended 32 1
3 E7 CB position open 64 1
3 E8 CB position closed 128 1
3 E9 Definite trip alarm signal activated 256 1
3 E10 Definite trip alarm signal reset 512 1
3 E11 AR lockout signal activated 1024 0
3 E12 AR lockout signal reset 2048 0
Default value of event mask 3V155 1023

Table 4.1.17.1-11Event codes E13...E22

Weighting
Channel Event Description Default value
factor
3 E13 Open CB command activated 1 0
3 E14 Open CB command reset 2 0
3 E15 Close CB command activated 4 0
3 E16 Close CB command reset 8 0
3 E17 CB reclosing failed signal activated 16 1
3 E18 CB reclosing failed signal reset 32 1
3 E19 CB reclosing disabled 64 1
3 E20 CB reclosing disabled reset 128 1
3 E21 AR cancelled 256 1
3 E22 AR cancelled reset 512 1
Default value of event mask 3V156 1008

121

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

4.1.18. Self-supervision (IRF) system

REF 610 is provided with an extensive self-supervision system which continuously
supervises the software and the electronics of the relay. It handles
run-time fault situations and informs the user about an existing fault via a LED on
the HMI and a text message on the LCD. There are two types of fault targets: IRF
targets and warnings.
Internal relay fault
When an internal relay fault is detected, which will prevent relay operation, the relay
will first try to eliminate it by restarting. Only after the fault has been found to be
permanent, the green target LED (ready) will begin to blink and the
self-supervision output contact will be activated. All other output contacts will be
returned to the initial state and locked for the internal relay fault. Further, a fault
target message will appear on the LCD, including a fault code.
IRF targets have the highest priority on the HMI. None of the other HMI targets can
override the IRF target. As long as the green target LED (ready) is blinking, the fault
target cannot be cleared. In case an internal fault disappears, the green target LED
(ready) will stop blinking and the relay will be returned to the normal service state,
but the fault target message will remain on the LCD until manually cleared.
The IRF code indicates the type of internal relay fault. When a fault appears, the
code is to be recorded and stated when ordering service. The fault codes are listed in
the following table:

Table 4.1.18-1 IRF codes

Fault code Type of fault
4 Error in output relay PO1
5 Error in output relay PO2
6 Error in output relay PO3
7 Error in output relay SO1
8 Error in output relay SO2
9 Error in the enable signal for output relay PO1, PO2, SO1
or SO2
10, 11, 12 Error in the feedback, enable signal or output relay PO1,
PO2, SO1 or SO2
13 Error in optional output relay SO3
14 Error in optional output relay SO4
15 Error in optional output relay SO5
16 Error in the enable signal for optional output relay SO3,
SO4 or SO5
17, 18, 19 Error in the feedback, enable signal or optional output
relay SO3, SO4 or SO5
20, 21 Auxiliary voltage dip
30 Faulty program memory
50, 59 Faulty work memory
51, 52, 53, 54, 56 Faulty parameter memory 1) 2)
55 Faulty parameter memory, calibration parameters
80 Optional I/O module missing
81 Optional I/O module unknown
82 Optional I/O module configuration error

122

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

Table 4.1.18-1 IRF codes

Fault code Type of fault
85 Power supply module faulty
86 Power supply module unknown
90 Hardware configuration error
95 Communication module unknown
104 Faulty configuration set (for IEC 60870-5-103)
131, 139, 195, 203, 222, 223 Internal reference voltage error
240 Faulty input, Light sensor 2
241 Faulty input, Light sensor 1
253 Error in the measuring unit
1) May be corrected by formatting to the factory setting.
2) The user-defined values will be set to zero during the internal fault state.

For further information on internal relay faults, refer to the Operator’s Manual.
Warnings
In case of a warning, the relay will continue to operate except for those protection
functions possibly affected by the fault, and the green target LED (ready) will
remain lit as during normal operation. Further, a fault target message, which
depending on the type of fault includes a fault code, will appear on the LCD. If more
than one type of fault occur at the same time, one single numeric code which
indicates all the faults will be displayed. The fault target message cannot be
manually cleared but will disappear with the fault.
When a fault appears, the fault target message is to be recorded and stated when
ordering service. The fault codes are listed in the following table:

Table 4.1.18-2 Warning codes

Fault Weight value
Battery low 1
Trip-circuit supervision 1) 2
Power supply module temperature high 4
Communication module faulty or missing 8
DNP 3.0 configuration error 16
DNP 3.0 module faulty 32
Continuous light detected by Light 64
sensor 1 or 2 1)
Σ 127
1)
The external fault warning can be routed to SO2 with SGF1/8.

For further information on warnings, refer to the Operator’s Manual.

4.1.19. Relay parameterization

Local parameterization
The parameters of the relay can be set either locally via the HMI or externally via
serial communication with the Relay Setting Tool. When the parameters are set
locally, the setting parameters can be chosen via the hierarchical menu structure.
The desired language can be selected for parameter descriptions. Refer to the
Operator’s Manual for further information.

123

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

External parameterization
The Relay Setting Tool is used for parameterizing the relay units. Adjusting the
parameter values using the Relay Setting Tool is done off-line, after which the
parameters can be downloaded to the relay via a communication port.

4.2. Design description

4.2.1. Input/output connections

All external circuits are connected to the terminals on the rear panel of the relay.
Terminals X2.1-_ are dimensioned for one 0.5...6.0 mm2 (awg 20-8) wire or two
max 2.5 mm2 wires and terminals X3.1-_ and X4.1-_ for one 0.2...2.5 mm2 (awg 24-
12) wire or two 0.2...1.0 mm2 (awg 24-16) wires.
The energizing phase currents of REF 610 are connected to terminals X2.1/1-2,
X2.1/3-4 and X2.1/5-6 (see table 4.2.1-1). The relay can also be used in single or
two-phase applications by leaving one or two energizing inputs unoccupied.
However, at least terminals X2.1/1-2 should be connected.
The energizing ground-fault current of REF 610 is connected to terminals X2.1/7-8
(see table 4.2.1-1).
The input terminals of the optional I/O module are located on connection socket
X3.1 (see tables 4.2.1-4 and 4.2.1-5).
Note!
REF 610 is provided with connection socket X3.1 only if the optional I/O module
has been installed.
Terminals X4.1/21-24 and X3.1/1-6 (optional) are digital input terminals (see table
4.2.1-5). The digital inputs can be used to generate a blocking signal, to unlatch
output contacts or for remote control of relay settings, for instance. The requested
functions are selected separately for each input in switchgroups SGB1...5. The
digital inputs can also be used to trigger the disturbance recorder; this function is
selected with SPA parameter V243.
The auxiliary voltage of the relay is connected to terminals X4.1/1-2 (see table
4.2.1-2). At dc supply, the positive lead is connected to terminal X4.1/1. The
permitted auxiliary voltage range of the relay is marked on the front panel of the
relay under the handle of the plug-in unit.
Output contacts PO1, PO2 and PO3 are heavy-duty trip contacts capable of
controlling most circuit breakers (see table 4.2.1-4). The signals to be routed to
PO1...PO3 are selected with the switches of switchgroups SGR1...SGR3. On
delivery from the factory, the trip signals from all the protection elements are routed
to PO1, PO2 and PO3.
Output contacts SO1...SO5 can be used for signalling on pickup and tripping of the
relay (see table 4.2.1-4). Output contacts SO3...SO5 are optional and available only
if the optional I/O module has been installed. The signals to be routed to SO1...SO5
are selected with the switches of switchgroups SGR4...SGR8. On delivery from the
factory, the pickup and alarm signals from all the protection elements are routed to
SO1 and SO2.

124

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

The IRF contact functions as an output contact for the self-supervision system of the
protection relay (see table 4.2.1-3). Under normal operating conditions the relay is
energized and the contact closed (X4.1/3-5). When a fault is detected by the
self-supervision system or the auxiliary voltage is disconnected, the output contact
will drop off and the contact close (X4.1/3-4).
Fig. 4.2.1.-1...Fig. 4.2.1.-3 present a rear view of REF 610, showing four connecting
sockets: one for measuring transformers, one for the optional I/O module, one for
power supply and one for optional serial communication.

X2.1

X3.1

11 12
X4.1
1 1
2 2
X5.1 3 3

10
4 4
5 5

9
X5.2 6 6
7 7
DANGER - RISK OF ELECTRIC SHOCK

8 8

8
TX 9 9
NEAR INSTRUMENT TERMINALS

X5.3 10 10

7
11 11
RX 12 12
13 13 6
14 14
TX 15 15
5

16 16
X5.4 17 17
18 18
4

RX
19 19
20 20
3

21 21
22 22
23 23
!

24 24

RearArcGlass_a
1

Fig. 4.2.1.-1 Rear view of REF 610 with the fibre-optic communication module
for plastic and glass fibre with light sensor inputs

125

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

X2.1

X3.1

11 12
X4.1
1 1
2 2
3 3

10
4 4
5 5

9
6 6
7 7

DANGER - RISK OF ELECTRIC SHOCK

8 8

8
9 9

NEAR INSTRUMENT TERMINALS

10 10

7
11 11
12 12
13 13

6
14 14
15 15

5
X5.5 16 16
17 17
6 18 18

4
5 19 19
4
3 20 20

3
2 21 21
1 22 22
23 23
!

24 24 2

RearRS_RE_61_a
1

Fig. 4.2.1.-2 Rear view of REF 610 with the RS-485 communication module

126

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

X2.1

X3.1

11 12
X4.1
1 1
2 2
3 3

10
4 4
5 5

9
6 6
7 7

DANGER - RISK OF ELECTRIC SHOCK

8 8

8
9 9

NEAR INSTRUMENT TERMINALS

10 10

7
11 11
12 12
13 13

6
14 14
15 15

5
16 16
8 17 17
7
6 18 18

4
X5.8 5 19 19
4
3 20 20

3
2 21 21
1 22 22
23 23
!

2
24 24
1

RearDNP_a
Fig. 4.2.1.-3 Rear view of REF 610 with the DNP 3.0 communication module
for RS-485

Table 4.2.1-1 Inputs for phase and ground-fault currents 1)

Function
REF610A12xxxx

REF610A15xxxx

REF610A51xxxx

REF610A52xxxx

REF610A55xxxx
REF610A11xxxx

Terminal

X2.1-1 la 1 A la 1 A la 1 A la 5 A la 5 A la 5 A
X2.1-2
X2.1-3 lb 1 A lb 1 A lb 1 A lb 5 A lb 5 A lb 5 A
X2.1-4
X2.1-5 lc 1 A lc 1 A lc 1 A lc 5 A lc 5 A lc 5 A
X2.1-6
X2.1-7 In 1 A In 0.2 A In 5 A In 1 A In 0.2 A In 5 A
X2.1-8
X2.1-9 - - - -
X2.1-10 - - - -
X2.1-11 - - - -
X2.1-12 - - - -
1)
The value denotes the rated current for each input.

127

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

Table 4.2.1-2 Auxiliary supply voltage

Terminal Function
X4.1-1 Input, +
X4.1-2 Input, -

Table 4.2.1-3 IRF contact

Terminal Function
X4.1-3 IRF, common
X4.1-4 Closed; IRF, or Uaux disconnected
X4.1-5 Closed; no IRF, and Uaux connected

Table 4.2.1-4 Output contacts

Terminal Function
X3.1-16 SO5, common 1)
X3.1-17 SO5, NC 1)
X3.1-18 SO5, NO 1)
X3.1-19 SO4, common 1)
X3.1-20 SO4, NC 1)
X3.1-21 SO4, NO 1)
X3.1-22 SO3, common 1)
X3.1-23 SO3, NC 1)
X3.1-24 SO3, NO 1)
X4.1-6 SO2, common
X4.1-7 SO2, NC
X4.1-8 SO2, NO
X4.1-9 SO1, common
X4.1-10 SO1, NC
X4.1-11 SO1, NO
X4.1-12 PO3 (trip lockout relay), NO
X4.1-13
X4.1-14 PO2, NO
X4.1-15
X4.1-16 PO1, NO
X4.1-17
X4.1-18 PO1 (TCS), NO
X4.1-19
X4.1-20 -
1) Optional

128

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

Table 4.2.1-5 Digital inputs

Terminal Function
X4.1-23 DI1
X4.1-24
X4.1-21 DI2
X4.1-22
X3.1-1 DI3 1)
X3.1-2
X3.1-3 DI4 1)
X3.1-4
X3.1-5 DI5 1)
X3.1-6
1)
Optional

4.2.2. Light sensor input connections

If REF 610 is provided with the optional communication module with light sensor
inputs, the pre-manufactured lens-sensor fibres are connected to inputs X5.1 and
X5.2 (see table 4.2.2-1 and Fig. 4.2.1.-1). For further information on the arc
protection, refer to section Arc protection.
Note!
REF 610 is provided with connection sockets X5.1 and X5.2 only if the optional
communication module with light sensor inputs has been installed (refer to section
Ordering information).

Table 4.2.2-1 Light sensor input connectors

Terminal Function
X5.1 Input Light sensor 1
X5.2 Input Light sensor 2

4.2.3. Serial communication connections

The optical front connection of the relay is used to connect the relay to the SPA bus
via the front communication cable 1MRS050698. If a PC compatible to the IrDA®
Standard specifications is used, wireless communication is possible as well. The
maximum wireless operating distance depends on the transceiver of the PC.
Rear communication of REF 610 is optional and the physical connection varies with
the communication option.

129

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

Plastic fibre-optic connection

If REF 610 is provided with the optional fibre-optic communication module for
plastic fibre, the fibre-optic cables are connected to terminals X5.3-RX (Receiver)
and X5.3-TX (Transmitter).

Table 4.2.3-1 Plastic fibre-optic rear connector

Terminal Function
X5.3-TX Transmitter
X5.3-RX Receiver

RS-485 connection
If REF 610 is provided with the optional RS-485 communication module, the cable
is connected to terminals X5.5/1-2 and X5.5/4-6. The connection socket is a 6-pin
header-type socket and the terminals are of screw compression type.
The RS-485 communication module follows the TIA/EIA-485 standard and is
intended to be used in a Daisy-chain bus wiring scheme with 2-wire, half-duplex,
multi-point communication. The maximum number of devices (nodes) connected to
the bus where REF 610 is being used is 32, and the maximum length of the bus is
1200 meters.
When connecting REF 610 to the bus, a quality twisted pair shielded cable is to be
used. The conductors of the pair are connected to A and B. If signal ground is being
used for balancing potential differences between devices/nodes, a quality dual
twisted pair shielded cable is to be used. In this case, one pair is connected to A and
B, and one of the conductors of the other pair to signal ground. When connecting
one device to another, A is connected to A and B to B.
The cable shield is to be connected directly to ground (shield GND) in one point/
device of the bus. Other devices connected to the bus should have the cable shield
connected to ground via a capacitor (shield GND via capacitor).
Note!
Signal ground can only be used for balancing potential differences between devices/
nodes if all devices connected to the bus have isolated RS-485 interfaces.
The RS-485 communication module is provided with jumpers for setting bus
termination and fail-safe biasing. The bus is to be terminated at both ends, which can
be done by using the internal termination resistor on the communication module.
The termination resistor is selected by setting jumper X5 to the ON position. If the
internal termination resistor of 120 Ω is used, the impedance of the cable should be
the same.
The bus is to be biased at one end to ensure fail-safe operation, which can be done
using the pull-up and pull-down resistors on the communication module. The
pull-up and pull-down resistors are selected by setting jumpers X3 and X4 to the ON
position.
The jumpers have been set to no termination (X5 in the OFF position) and no biasing
(X3 and X4 in the OFF position) as default.

130

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

off
on X3

off X4
on

off
X5
on

RS_JumpersREF610_a

Fig. 4.2.3.-1 Jumper location on the RS-485 communication module

Table 4.2.3-2 RS-485 rear connector

Terminal Function
X5.5-6 Data A (+)
X5.5-5 Data B (-)
X5.5-4 Signal GND (for potential balancing)
X5.5-3 -
X5.5-2 Shield GND (via capacitor)
X5.5-1 Shield GND

Combined fibre-optic connection (plastic and glass)

If REF 610 is provided with the optional fibre-optic communication module for
plastic and glass fibre, the plastic fibre-optic cables are connected to terminals
X5.3-RX (Receiver) and X5.3-TX (Transmitter) and the glass fibre-optic cables to
terminals X5.4-RX (Receiver) and X5.4-TX (Transmitter).
The fibre-optic interface is selected with jumpers X6 and X2 located on the PCB of
the communication module (see Fig. 4.2.3.-2).

Table 4.2.3-3 Transmitter selection

Transmitter Position of jumper X6
Plastic X5.3-TX
Glass X5.4-TX

131

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

Table 4.2.3-4 Receiver selection

Transmitter Position of jumper X2
Plastic X5.3-RX
Glass X5.4-RX

X5.3-TX(plastic)

X5.3-RX(plastic)
Fibre-optic Interface
X5.3 TX
X5.4 TX X6
X5.3 RX
X5.4 RX X2

X6

X2

X5.4-TX(glass)

X5.4-RX(glass)

JunpersMixREF610_a

Fig. 4.2.3.-2 Jumper location on the communication module for plastic and
glass fibre

Table 4.2.3-5 Fibre-optic rear connectors (plastic and glass)

Terminal Function
X5.3-TX Transmitter for plastic fibre
X5.3-RX Receiver for plastic fibre
X5.4-TX Transmitter for glass fibre
X5.4-RX Receiver for plastic fibre

RS-485 connection for the DNP 3.0 communication module

If REF 610 is provided with the optional DNP 3.0 communication module, the cable
is connected to terminals X5.8/1-2 and X5.8/4-8. The connection socket is a 8-pin
header-type socket and the terminals are of screw compression type.
The DNP communication module follows the DNP standard and is intended to be
used in a Daisy-chain bus wiring scheme with 2- or 4-wire, half-duplex, multi-point
communication. The maximum number of devices (nodes) connected to the bus
where REF 610 is being used is 32, and the maximum length of the bus is 1200
meters in optimum conditions and with slow communication speed.

132

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

When connecting REF 610 to the bus, a quality twisted pair shielded cable is to be
used. The conductors of the pair are connected to A and B. If signal ground is being
used for balancing potential differences between devices/nodes, a quality dual
twisted pair shielded cable is to be used. In this case, one pair is connected to A and
B, and one of the conductors of the other pair to signal ground. When connecting
one device to another, A is connected to A and B to B.
When using a 4-wire bus, one pair is connected to +RX and -RX and the other to
+TX and -TX. If signal ground is being used, a quality cable with three or several
pairs is to be used and one of the conductors of a pair connected to signal ground.
The cable shield is to be connected directly to ground (shield GND) in one
point/device of the bus. Other devices connected to the bus should have the cable
shield connected to ground via a capacitor (shield GND via capacitor).
Note!
Signal ground can only be used for balancing potential differences between
devices/nodes if all devices connected to the bus have isolated DNP interfaces.
The DNP communication module is provided with jumpers for setting bus
termination and fail-safe biasing. The bus is to be terminated at both ends, which can
be done by using the internal termination resistor on the DNP communication
module. The termination resistor is selected by setting jumper X6 or/and X12 to the
ON position. If the internal termination resistor of 120 Ω is used, the impedance of
the cable should be the same.
The bus is to be biased at one end to ensure fail-safe operation, which can be done
using the pull-up and pull-down resistors on the communication module. The
pull-up and pull-down resistors are selected by setting jumpers X8, X7, X13 and
X11 to the ON position.
The jumpers have been set to no termination (X5 in the OFF position) and no biasing
(X8, X7, X13 and X11 in the OFF position) as default.

Table 4.2.3-6 RS-485 rear connector (DNP 3.0)

Terminal Function
X5.8-8 Data A (+ RX)
X5.8-7 Data B (- RX)
X5.8-6 Data A (+ TX)
X5.8-5 Data B (- TX)
X5.8-4 Signal GND (for potential balancing)
X5.8-3 -
X5.8-2 Shield GND (via capacitor)
X5.8-1 Shield GND

133

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

Table 4.2.3-7 Jumper numbering

Terminal Function Signal
X8 Pull-up Data A (+ TX)
X6 Termination TX
X7 Pull-down Data B (- TX)
X13 Pull-up Data A (+ RX)
X12 Termination RX
X11 Pull-down Data B (- RX)
X14 4-wire/2-wire

ON X13
X8 ON
ON X12
X6 ON
ON X11
X7 ON
X14
DNP_JumpersREF610_a

4-Wire
2-Wire

Fig. 4.2.3.-3 Jumper location on the DNP 3.0 communication module

4.2.4. Technical data

Table 4.2.4-1 Dimensions 1)

Width, frame 177 mm, case 164 mm
Height, frame 177 mm (4U), case 160 mm
Depth, case 149.3 mm
Weight of the relay ~3.5 kg
Weight of the spare unit ~1.8 kg
1)
For dimension drawings, refer to the Installation Manual (1MRS 752265-MUM).

Table 4.2.4-2 Power supply

Uaux rated
• REF610AxxHxxx Ur=100/110/120/220/240 V ac
Ur=110/125/220/250 V dc
• REF610AxxLxxx Ur=24/48/60 V dc
Uaux variation (temporary)

134

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

Table 4.2.4-2 Power supply

• REF610AxxHxxx 85...110% of Ur (ac)
80...120% of Ur (dc)
• REF610AxxLxxx 80...120% of Ur (dc)
Burden of auxiliary voltage supply under quiescent <9 W/13 W
(Pq)/operating condition
Ripple in the dc auxiliary voltage Max 12% of the dc value
Interruption time in the auxiliary dc voltage without <50 ms at Uaux rated
resetting the relay
Time to trip from switching on the auxiliary voltage <350 ms
Internal over temperature limit +100°C
Fuse type T2A/250 V

Table 4.2.4-3 Energizing inputs

Rated frequency 50/60 Hz ± 5 Hz
Rated current, In (CT) 0.2 A 1A 5A
Thermal withstand capability
• continuously • 1.5 A 4A 20 A
• for 1 s • 20 A 100 A 500 A
• for 10 s •5A 25 A 100 A
Dynamic current withstand
• half-wave value • 50 A 250 A 1250 A
Input impedance <750 mΩ <100 mΩ <20 mΩ

Table 4.2.4-4 Measuring range

Measured currents on phases Ia, Ib and Ic as multiples of the rated 0...50 x In (CT)
currents of the energizing inputs
Ground-fault current as a multiple of the rated current of the energizing 0...8 x In (CT)
input

Table 4.2.4-5 Digital inputs

Operating range ±20% of the rated voltage
Rated voltage DI1...DI2 DI3...DI5 (optional)
• REF610AxxHxxx 110/125/220/250 V dc
• REF610AxxLxxx 24/48/60/110/125/220/250 V dc
• REF610AxxxxLx 24/48/60/110/125/220/250 V dc
• REF610AxxxxHx 110/125/220/250 V dc
Current drain 2...18 mA
Power consumption/input ≤ 0.9 W

Table 4.2.4-6 Non-trip output SO1 and optional SO4 and SO5
Rated voltage 250 V ac/dc
Continuous carry 5A
Make and carry for 3.0 s 15 A
Make and carry for 0.5 s 30 A
Breaking capacity when the control-circuit time 1 A/0.25 A/0.15 A
constant L/R <40 ms, at 48/110/220 V dc (5 A/3 A/1 A for series connection of
SO4 and SO5)
Minimum contact load 100 mA at 24 V ac/dc

135

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

Table 4.2.4-7 Non-trip output SO2, optional SO3, and IRF output
Rated voltage 250 V ac/dc
Continuous carry 5A
Make and carry for 3.0 s 10 A
Make and carry for 0.5 s 15 A
Breaking capacity when the control-circuit time 1 A/0.25 A/0.15 A
constant L/R <40 ms, at 48/110/220 V dc
Minimum contact load 100 mA at 24 V ac/dc

Table 4.2.4-8 Trip outputs (PO1, PO2, PO3)

Rated voltage 250 V ac/dc
Continuous carry 5A
Make and carry for 3.0 s 15 A
Make and carry for 0.5 s 30 A
Breaking capacity when the control-circuit time 5 A/3 A/1 A
constant L/R <40 ms, at 48/110/220 V dc (PO1 with
both contacts connected in series)
Minimum contact load 100 mA at 24 V ac/dc
TCS
• Control voltage range 20...265 V ac/dc
• Current drain through the supervision circuit ~1.5 mA
• Minimum voltage over a contact 20 V ac/dc (15...20 V)

Table 4.2.4-9 Lens sensor and optic fibre for arc protection
Normal service temperature range -40...+100°C
Maximum service temperature range, max 1 h +140°C
Minimum permissible bending radius of the 100 mm
connection fibre

Table 4.2.4-10 Enclosure class of the flush-mounted relay

Front side IP 54 (NEMA 35)
Rear side, top of the relay IP 401)
Rear side, connection terminals IP 202)
1) IP 40
- Non protected
- Protected against solid objects greater than 1.0mm
2) IP 20
- Non protected
- Protected against solid objects greater than 12mm

Table 4.2.4-11 Environmental tests and conditions

Recommended service temperature range -10...+55°C
(continuous)
Limit temperature range (short-term) -40...+70°C
Transport and storage temperature range -40...+85°C according to
IEC 60068-2-48
Dry heat test According to IEC 60068-2-2
Dry cold test According to IEC 60068-2-1
Damp heat test, cyclic According to IEC 60068-2-30

136

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

Table 4.2.4-12 Electromagnetic compatibility tests

EMC immunity test level meets the requirements listed below
1 MHz burst disturbance test, class III According to IEC 60255-22-1
• Common mode 2.5 kV
• Differential mode 1.0 kV
Electrostatic discharge test, class IV According to IEC 61000-4-2,
IEC 60255-22-2 and
ANSI C37.90.3-2001
• For contact discharge 8 kV
• For air discharge 15 kV
Radio frequency interference tests
• Conducted, common mode According to IEC 61000-4-6 and
IEC 60255-22-6 (2000)
10 V (rms), f=150 kHz...80 MHz
• Radiated, amplitude-modulated According to IEC 61000-4-3 and
IEC 60255-22-3 (2000)
10 V/m (rms), f=80...1000 MHz
• Radiated, pulse-modulated According to the ENV 50204 and
IEC 60255-22-3 (2000)
10 V/m, f=900 MHz
Fast transient disturbance tests According to IEC 60255-22-4 and
IEC 61000-4-4
• Trip outputs, energizing inputs, power supply 4 kV
• I/O ports 2 kV
Surge immunity test According to IEC 61000-4-5
• Trip outputs, energizing inputs, power supply 4 kV, line-to-ground
2 kV, line-to-line
• I/O ports 2 kV, line-to-ground
1 kV, line-to-line
Power frequency (50 Hz) magnetic field 300 A/m continuous
IEC 61000-4-8
Voltage dips and short interruptions According to IEC 61000-4-11
30%/10 ms
60%/100 ms
60%/1000 ms
>95%/5000 ms
Electromagnetic emission tests According to the EN 55011
• Conducted, RF-emission (Mains terminal) EN 55011, class A, IEC 60255-25
• Radiated RF-emission EN 55011, class A, IEC 60255-25
CE approval Complies with the EMC directive 89/
336/EEC and the LV directive 73/23/
EEC

Table 4.2.4-13 Standard tests

Insulation tests
Dielectric tests According to IEC 60255-5
• Test voltage 2 kV, 50 Hz, 1 min
Impulse voltage test According to IEC 60255-5
• Test voltage 5 kV, unipolar impulses, waveform
1.2/50 μs, source energy 0.5 J

137

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

Table 4.2.4-13 Standard tests

Insulation resistance measurements According to IEC 60255-5
• Isolation resistance >100 MΩ, 500 V dc
Mechanical tests
Vibration tests (sinusoidal) According to IEC 60255-21-1, class I
Shock and bump test According to IEC 60255-21-2, class I

Table 4.2.4-14 Data communication

Rear interface, connector X5.3, X5.4, X5.5 or X5.8
• Fibre-optic or RS-485 connection
• SPA bus, IEC 60870-5-103, DNP 3.0 or Modbus protocol
• 9.6 or 4.8 kbps (additionally 2.4, 1.2 or 0.3 kbps for Modbus)
Front interface
• Optical connection (infrared): wirelessly or via the front communication cable
(1MRS050698)
• SPA bus protocol
• 9.6 or 4.8 kbps (9.6 kbps with front communication cable)

Auxiliary voltage
REF 610 requires a secured auxiliary voltage supply to operate. The internal power
supply of the relay forms the voltages required by the relay electronics. The power
supply is a galvanically isolated (flyback-type) DC/DC converter. When the
auxiliary voltage is connected, the green target LED (ready) on the front panel will
be on. For detailed information on power supply, refer to table 4.2.4-2.
The primary side of the power supply is protected with a fuse located on the PCB of
the relay.

138

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

5. Application examples

5.1. Auto-reclose function

5.1.1. Fast tripping and initiation of shot 1 using two protection

elements
In several applications, such as fuse-saving applications involving down-stream
fuses, tripping and initiation of shot 1 should be fast (instantaneous or short-time
delayed) and of shot 2 and 3, and definite tripping time delayed.
In this example, two overcurrent elements are used, 51P and 50P-1. Element 50P-1
is given an instantaneous characteristic and element 51P a time delay. By setting
SG2/2 to 1 and SG2/7 to 1, element 50P-1 will be blocked by the AR function during
shot 2 and 3.

Open CB

Close CB

79

Trip Close CB
51P

Block 50P-1 at
Shot 1,2 and 3
SG2/2=1 Block 50P-1
SG2/7=1
50P-1 Trip

50P-1 Trip 51P Trip 51P Trip 51P Trip

Block 50P-1 Block 50P-1 Block 50P-1

CB Closed

CB Open
Shot 1 Shot 2 Shot 3 Definite Trip

50P-1 TDLY 51P TDLY 51P TDLY 51P TDLY

Fig. 5.1.1.-1 Fast initiation of shot 1 using one fast and one delayed element
In case of a short-circuit in the network, element 50P-1 will trip the circuit breaker
and initiate shot 1. At the time of shot initiation, the blocking of element 50P-1 will
be activated. If the network fault is not cleared, element 51P will trip the circuit
breaker and continue the auto-reclose sequence to shot 2, shot 3 and finally definite
tripping.

139

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

As the set pickup value of element 51P in this example is higher than that of element
50P-1, as sometimes is the case, it is possible that the current will not exceed the set
pickup value of element 51P while the blocking of element 50P-1 is active. This will
lead to a pumping effect when the AR function is reset (the blocking of element 50P-
1 included), i.e. the AR sequence will pickup over and over again.
To avoid such a pumping effect, a cutout time is used. The cutout time, like the reset
time, will pickup when the set open time elapses and the AR function issues a
reclosing command to the circuit breaker. By setting the cutout time to be shorter
than the reset time (e.g. half of the reset time), the blocking of element 50P-1 (in this
case) will be reset before the AR function. Element 50P-1 will now be able to
continue the AR sequence and the pumping effect will thus be avoided.

5.1.2. Fast tripping and initiation of shot 1 using pickup signals

An alternative way to achieve fast tripping and shot initiation (typical for certain
countries, such as Finland), is to use pickup signals from protection elements for
shot initiation. The AR function of REF 610 can be initiated by the pickup signals
from elements 51P and 51N.
The pickup time of elements 51P and 51N is very short but can be extended with the settings
AR 51P Pickup Delay and AR 51N Pickup Delay of the AR function.
When the set pickup delay elapses, the shot will be initiated and the AR function will trip the
circuit breaker by issuing the Open CB Command.

Open CB

79

Trip Shots 1, 2 and 3 initiation

51P
Pick up t Shots 1 initiation
0

Open CB Command Open CB

51P Pick up
delay Close CB Command Close CB

Open CB Close CB Close CB Close CB

Command Command Command Command
51P Pickup
51P Pickup 51P Trip 51P Trip
Open CB
Command

CB Closed

CB Open
Shot 1 Shot 2 Shot 3 Definite Trip

51P TDLY 51P TDLY 51P TDLY 51P TDLY

Fig. 5.1.2.-1 Fast initiation of shot 1 using pickup signals

140

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

Shot initiation by a pickup signal applies only to shot 1, and to definite tripping, i.e.
when no more shots are allowed but the network fault has not been cleared. In this
case, the AR function will trip the circuit breaker on expiration of AR 51P Pickup
Delay and AR 51N Pickup Delay.
Note!
The signal Open CB Command must be routed to the output contact used for
tripping the circuit breaker.
Note!
At the factory default delay of 300 s for AR 51P Pickup Delay and AR 51N
Pickup Delay, the pickup signals will, in practise, not be used for shot initiation.
However, if elements 51P or 51N have been given an IDMT (mode) characteristic,
the factory default delay of 300 s will function as a trip time limiter. With small
currents, the operate time at IDMT (mode) characteristic may be relatively long.
However, since the pickup signals are always routed to the AR function, the circuit
breaker will be tripped and a shot initiated (provided that the signal Open CB
Command has been routed to the trip output contact) on expiration of the factory
default delay.
Note!
When using AR 51P Pickup Delay and AR 51N Pickup Delay for shot
initiation and the signal Open CB Command has been routed to the trip output
contact, elements 51P and 51N should not be used for blocking of shot 1.

5.1.3. Selecting adaptive sequence length

The auto-reclose sequence can be set to adapt to the fault current, either through
blocking of shot initiation or disable of the AR function.
In the examples below, three overcurrent elements (51P, 50P-1 and 50P-2) are used
and the number of shots of the AR sequence vary depending on which elements
trips.
Example 1
Pickup by checking that the switches have been properly set:

Settings Function
SG1/1=1 Blocking of initiation of shot 1 by the trip signal from element 50P-1
SG3/1=1 Disable of the AR function by the trip signal from element 50P-2
Number of shots = 3

If one or several phase currents

• exceed the set pickup value of element 51P but not of elements 50P-1 and 50P-2,
the AR sequence will include shot 1, 2 and 3.
• exceed the set pickup value of elements 51P and 50P-1 but not of element 50P-2,
the AR sequence will include shot 2 and 3.
• exceed the set pickup value of elements 51P, 50P-1 and 50P-2, no shots will be
performed (AR function disabled).
Note!

141

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

Element 50P-2 should have the shortest and element 51P the longest operate time.
Example 2
Pickup by checking that the switches have been properly set:

Settings Function
SG1/5=1 Blocking of initiation of shot 2 and 3 by the trip signal from element
50P-1
SG3/1=1 Disable of the AR function by the trip signal from element 50P-2
Number of shots = 3

If one or several phase currents

• exceed the set pickup value of element 51P but not of elements 50P-1 and 50P-2,
the AR sequence will include shot 1, 2 and 3
• exceed the set pickup value of elements 51P and 50P-1 but not of element 50P-2,
the AR sequence includes only shot 1
• exceed the set pickup value of elements 51P, 50P-1 and 50P-2, no shots will be
performed (AR function disabled).
Note!
Element 50P-2 should have the shortest and element 51P the longest operate time.

5.2. Arc protection

5.2.1. Arc protection with one REF 610 relay

In installations with limited possibilities to realize signalling between relays
protecting incoming and outgoing feeders, or if only the relay for the incoming
feeder is to be exchanged, an arc protection with a lower protective level can be
achieved with one protection relay.
An arc protection with one REF 610 only (see Fig. 5.2.1.-1) is realized by installing
two arc lens sensors, connected to the relay protecting the incoming feeder, to detect
an arc on the busbar. On arc detection, the arc protection element will trip the circuit
breaker of the incoming feeder. The maximum recommended installation distance
between the two lens sensors in the busbar area is 6 meters and the maximum
distance from a lens sensor to the end of the busbar 3 meters.

142

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

52

PO3

REF 610

PO1
52

52 52 52 52

Fig. 5.2.1.-1 Arc protection with one REF 610

143

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

5.2.2. Arc protection with several REF 610 relays

When using several REF 610 relays (see Fig. 5.2.2.-1), a REF 610 protecting an
outgoing feeder will trip the circuit breaker of the outgoing feeder when detecting
an arc at the cable terminations. If the REF 610 protecting the outgoing feeder
detects an arc on the busbar (via the other lens sensor), however, it will generate a
signal to the REF 610 protecting the incoming feeder. On detection of the signal, the
REF 610 protecting the incoming feeder will trip the circuit breaker of the incoming
feeder and generate an external trip signal to all REF 610 relays protecting outgoing
feeders, which in turn will result in tripping of all circuit breakers of outgoing
feeders.
For maximum safety, the REF 610 relays can be configured to trip all circuit
breakers, regardless of where the arc is detected.

52

PO3 DI1

REF 610

PO1 SO1
52

DI1 DI1 DI1 DI1

Q3
52 52 52 52

SO1 SO1 SO1 SO1

Fig. 5.2.2.-1 Arc protection with several REF 610 relays

144

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

5.2.3. Arc protection with several REF 610 relays and one REA 101
When realizing an arc protection with both REF 610 relays and an REA 101 (see Fig.
5.2.3.-1), the cable terminations of outgoing feeders are protected by REF 610 relays
using one lens sensor for each relay. The busbar and the incoming feeder is protected
by the sensor loop of the REA 101.
On arc detection at the cable terminations, REF 610 will trip the circuit breaker of
the outgoing feeder. However, on detection of an arc on the busbar, REA 101 will
trip the circuit breaker of the incoming feeder and generate an external trip signal to
all REF 610 relays protecting outgoing feeders, which in turn will result in tripping
of all circuit breakers of outgoing feeders.

52

HSO2

REA 101

HSO1 TRIP3
52

Fiber sensor loop

DI1 DI1 DI1 DI1

Q3
52 52 52 52

Fig. 5.2.3.-1 Arc protection with REF 610 and REA 101

145

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

6. Ordering information
When ordering REF 610 protection relays and/or accessories, please specify the
following:
• Order number
• Quantity
The order number identifies the protection relay type and hardware as described in
the figures below and is labelled on the marking strip under the lower handle of the
relay.
Use the ordering key in Fig. 6.-1 to generate the order number when ordering
complete protection relays. HMI language set numbers, and corresponding
terminology and languages included, are described in Table 6-1.

REF610B55HCNP XX
Language set: HMI language set number

Communication module: P = plastic fibre

M = plastic fibre with input for arc protection
G = plastic and glass fibre
K = plastic and glass fibre with input for arc protection
R = RS-485
T = RS-485 with input for arc protection
D = RS-485 including DNP 3.0 protocol
E = RS-485 including DNP 3.0 protocol and
input for arc protection
N = none

I/O extension module: H = 3xSO and 3xDI (110/125/220/250 V dc)

L = 3xSO and 3xDI (24/48/60/110/125/220/250 V dc)
N = none

Power supply: H = 100-240 V ac/110-250 V dc, 2xDI

(110/125/220/250 V dc), 3xPO, 2xSO
L = 24-60 V dc, 2xDI (24/48/60/110/125/220/250 V dc),

OrdInfo1REF610_b
3xPO, 2xSO

Ground-fault current input: 5 = 5A, 1=1A, 2=0.2A

Phase-current inputs: 5 = 5A, 1=1A

Revision

Fig. 6.-1 Ordering key for complete relays

Use the ordering key in Fig. 6.-2 to generate the order number when ordering spare
units. HMI language set numbers, and corresponding terminology and languages
included, are described in Table 6-1.

146

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

REF610B55HSNS XX
Language set: HMI language set number

I/O extension module: H = 3xSO and 3xDI (110/125/220/250 V dc)

L = 3xSO and 3xDI (24/48/60/110/125/220/250 V dc)
N = none

Power supply: H = 100-240 V ac/110-250 V dc, 2xDI

(110/125/220/250 V dc), 3xPO, 2xSO
L = 24-60 V dc, 2xDI (24/48/60/110/125/220/250 V dc),
3xPO, 2xSO

OrdInfo2REF610_b
Ground-fault current input: 5 = 5A, 1=1A, 2=0.2A

Phase-current inputs: 5 = 5A, 1=1A

Revision

Fig. 6.-2 Ordering key for spare units

Table 6.-1
Language set number Terminology Languages
11 ANSI English, Español, Portuguese

The following accessories are available:

Item Order number

Semi-flush mounting kit 1MRS050696
25o)
Inclined (/ semi-flush mounting kit 1MRS050831
Wall mounting kit 1MRS050697
19” Rack mounting kit, side-by-side 1MRS050695
19" Rack mounting kit, single relay 1MRS050694
19" Rack mounting kit for single relay and RTXP18 1MRS050783
19" equipment frame mounting (Combiflex), plain bracket 1MRS061208
19" equipment frame mounting (Combiflex), bracket for RTXP18 1MRS061207
Pre-manufactured lens-sensor and optic fibre for arc protection
• 1.5 m ±3% 1MRS120534-1.5
• 3 m ±3% 1MRS120534-3.0
• 5 m ±3% 1MRS120534-5.0
Front communication cable 1MRS050698

147

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

7. Revision History of REF 610

7.1. Revision identification

The different revisions of REF 610 products may involve functional additions and
changes to the product.

Table 7.1.-1
Product Revision Release
REF 610 A Q4/2004
REF 610 B Q1/2005

7.2. Changes and additions to earlier released revision A

General
• The product can be ordered with language set using ANSI terminology

148

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

8. References
Other available manuals:
• Operator’s Manual, 1MRS 755311
• Installation Manual, 1MRS 752265-MUM

149

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

9. Abbreviations
ANSI American National Standards Institute
AR Auto-reclose
ASCII American Standard Code for Information Interchange
AWG American wire gauge
CB Circuit breaker
CBFAIL Circuit-breaker failure protection
CD Change detect
CPU Central Processing Unit
CRC Cyclical Redundancy Check
CT Current transformer
DI Digital input
EEPROM Electrically erasable programmable read-only memory
EMC Electromagnetic compatibility
EPA Enhanced Performance Architecture
ER Event record
FR Fault record
GI General interrogation
HMI Human-Machine Interface
HR Holding register
IDMT (mode) Inverse definite minimum time
IEC International Electrotechnical Commission
IEC_103 Standard IEC 60870-5-103
IEEE Institute of Electrical and Electronics Engineers, Inc.
IR Input registers
IRF Internal relay fault
ISO International Organization for Standardization
LCD Liquid Crystal Display
LED Light-emitting diode
LRC Longitudinal Redundancy Check
LSB Least significant bit
MP Minute-pulse
MSB Most significant bit
MV Medium Voltage
NC Normally closed
NO Normally open
OSI Open System Interconnection
PC Personal Computer
PCB Printed Circuit Board
PLC Programmable Logical Controller
PO1, PO2, PO3 Trip outputs
RMS Root Mean Square
RTU Remote Terminal Unit

150

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

SGB Switchgroups for digital inputs

SGF Switchgroups for functions
SGL Switchgroups for programmable LEDs
SGR Switchgroups for output contacts
SO1...SO5 Non-trip outputs
SP Second-pulse
TCS Trip-circuit supervision
UDR User-defined register
UR Unsolicited reporting

151

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

10. Check lists

Table 10.-1Setting group 1
Group/
Customer’s
Variable Channel 1 Setting range Default setting
setting
(R, W, P)
Pickup value of element 1S1 0.30...5.0 x In (CT) 0.30 x In (CT)
51P
Operate time of element 1S2 0.05...300 s 0.05 s
51P (51P TDLY)
Time/current characteristic 1S3 0...8 0
for element 51P
Time multiplier 51P TD IEC 1S4 0.05...1.00 0.05
Time multiplier 51P TD 1S5 1.0...15.0 1.0
ANSI
Resetting time of element 1S6 0.05...2.50 s 0.05 s
51P (51P RSET)
Pickup value of element 1S7 0.50...35.0 x In (CT) 0.50 x In (CT)
50P-1
Operate time of element 1S8 0.04...300 s 0.04 s
50P-1 (50P-1 TDLY)
Pickup value of element 1S9 0.50...35.0 x In (CT) 0.50 x In (CT)
50P-2
Operate time of element 1S10 0.04...30.0 s 0.04 s
50P-2 (50P-2 TDLY)
Pickup value of element 1S11 1.0...100% In (CT) 1.0% In (CT)
51N
Operate time of element 1S12 0.05...300 s 0.05 s
51N (51N TDLY)
Time/current characteristic 1S13 0...8 0
for element 51N
Time multiplier 51N TD IEC 1S14 0.05...1.00 s 0.05 s
Time multiplier 51N TD 1S15 1.0…15.0 1.0
ANSI
Resetting time of element 1S16 0.05...2.50 0.05
51N (51N RSET)
Pickup value of element 1S17 5.0...400% In (CT) 5.0% In (CT)
50N
Operate time of element 1S18 0.05...300 s 0.05 s
50N (50N TDLY)
Pickup value of element 46 1S19 10...100% 100%
Operate time of element 1S20 1...300 s 60 s
46 (46 TDLY)
Full load current 1S21 0.30...1.50 x In (CT) 0.30 x In (CT)
Time constant of element 1S22 1...200 min 1 min
49
Alarm level of element 49 1S23 50...100% 49 trip 95% 49 trip
Operate time of CBFAIL 1S24 0.10...60.0 s 0.10 s
(Trip Fail)

152

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

Table 10.-1Setting group 1

Group/
Customer’s
Variable Channel 1 Setting range Default setting
setting
(R, W, P)
Number of AR shots 1S25 0 = AR is not in use 0
1 = shot 1
2 = shot 1 and 2
3 = shot 1, 2 and 3
Current limit Arc50P of 1S26 0.50...35.0 x In (CT) 2.50 x In (CT)
element ARC
Current limit Arc51N of 1S27 5.0...400% In (CT) 20% In (CT)
element ARC 2)
Checksum, SGF 1 1S61 0...255 0
Checksum, SGF 2 1S62 0...127 0
Checksum, SGF 3 1S63 0...127 120
Checksum, SGF 4 1S64 0...63 0
Checksum, SGF 5 1S65 0...255 0
Checksum, SGB 1 1S71 0...1048575 0
Checksum, SGB 2 1S72 0...1048575 0
Checksum, SGB 3 1S73 0...1048575 0
Checksum, SGB 4 1S74 0...1048575 0
Checksum, SGB 5 1S75 0...1048575 0
Checksum, SGR 1 1S81 0...8388607 2108074
Checksum, SGR 2 1S82 0...8388607 2108074
Checksum, SGR 3 1S83 0...8388607 2108074
Checksum, SGR 4 1S84 0...8388607 5461
Checksum, SGR 5 1S85 0...8388607 5461
Checksum, SGR 6 1S86 0...8388607 0
Checksum, SGR 7 1S87 0...8388607 0
Checksum, SGR 8 1S88 0...8388607 0
Checksum, SGL 1 1S91 0...2097151 0
Checksum, SGL 2 1S92 0...2097151 0
Checksum, SGL 3 1S93 0...2097151 0
Checksum, SGL 4 1S94 0...2097151 0
Checksum, SGL 5 1S95 0...2097151 0
Checksum, SGL 6 1S96 0...2097151 0
Checksum, SGL 7 1S97 0...2097151 0
Checksum, SGL 8 1S98 0...2097151 0

Table 10.-2Setting group 2

Group/
Default Customer’
Variable Channel 2 Setting range
setting s setting
(R, W, P)
Pickup value of element 2S1 0.30...5.0 x In (CT) 0.30 x In (CT)
51P
Operate time of element 2S2 0.05...300 s 0.05 s
51P (51P TDLY)
Time/current characteristic 2S3 0...8 0
for element 51P
Time multiplier 51P TD IEC 2S4 0.05...1.00 0.05

153

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

Table 10.-2Setting group 2

Group/
Default Customer’
Variable Channel 2 Setting range
setting s setting
(R, W, P)
Time multiplier 51P TD 2S5 1.0...15.0 1.0
ANSI
Resetting time of element 2S6 0.05...2.50 s 0.05 s
51P (51P RSET)
Pickup value of element 2S7 0.50...35.0 x In (CT) 0.50 x In (CT)
50P-1
Operate time of element 2S8 0.04...300 s 0.04 s
50P-1 (50P-1 TDLY)
Pickup value of element 2S9 0.50...35.0 x In (CT) 0.50 x In (CT)
50P-2
Operate time of element 2S10 0.04...30.0 s 0.04 s
50P-2 (50P-2 TDLY)
Pickup value of element 2S11 1.0...100% In (CT) 1.0% In (CT)
51N
Operate time of element 2S12 0.05...300 s 0.05 s
51N (51N TDLY)
Time/current characteristic 2S13 0...8 0
for element 51N
Time multiplier 51N TD IEC 2S14 0.05...1.00 s 0.05 s
Time multiplier 51N TD 2S15 1.0…15.0 1.0
ANSI
Resetting time of element 2S16 0.05...2.50 0.05
51N (51N RSET)
Pickup value of element 2S17 5.0...400% In (CT) 5.0% In (CT)
50N
Operate time of element 2S18 0.05...300 s 0.05 s
50N (50N TDLY)
Pickup value of element 46 2S19 10...100% 100%
Operate time of element 46 2S20 1...300 s 60 s
Full load current 2S21 0.30...1.50 x In (CT) 0.30 x In (CT)
Time constant of element 2S22 1...200 min 1 min
49
Alarm level of element 49 2S23 50...100% 49 Trip 95% 49 Trip
Operate time of CBFAIL 2S24 0.10...60.0 s 0.10 s
(Trip Fail)
Number of AR shots 2S25 0 = AR is not in use 0
1 = shot 1
2 = shot 1 and 2
3 = shot 1, 2 and 3
Current limit Arc50P of 2S26 0.50...35.0 x In (CT) 2.50 x In (CT)
element ARC
Current limit Arc51N of 2S27 5.0...400% In (CT) 20% In (CT)
element ARC 2)
Checksum, SGF 1 2S61 0...255 0
Checksum, SGF 2 2S62 0...127 0
Checksum, SGF 3 2S63 0...127 120
Checksum, SGF 4 2S64 0...63 0
Checksum, SGF 5 2S65 0...255 0

154

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

Table 10.-2Setting group 2

Group/
Default Customer’
Variable Channel 2 Setting range
setting s setting
(R, W, P)
Checksum, SGB 1 2S71 0...1048575 0
Checksum, SGB 2 2S72 0...1048575 0
Checksum, SGB 3 2S73 0...1048575 0
Checksum, SGB 4 2S74 0...1048575 0
Checksum, SGB 5 2S75 0...1048575 0
Checksum, SGR 1 2S81 0...8388607 10922
Checksum, SGR 2 2S82 0...8388607 10922
Checksum, SGR 3 2S83 0...8388607 10922
Checksum, SGR 4 2S84 0...8388607 5461
Checksum, SGR 5 2S85 0...8388607 5461
Checksum, SGR 6 2S86 0...8388607 0
Checksum, SGR 7 2S87 0...8388607 0
Checksum, SGR 8 2S88 0...8388607 0
Checksum, SGL 1 2S91 0...2097151 0
Checksum, SGL 2 2S92 0...2097151 0
Checksum, SGL 3 2S93 0...2097151 0
Checksum, SGL 4 2S94 0...2097151 0
Checksum, SGL 5 2S95 0...2097151 0
Checksum, SGL 6 2S96 0...2097151 0
Checksum, SGL 7 2S97 0...2097151 0
Checksum, SGL 8 2S98 0...2097151 0

Table 10.-3Control parameters

Parameter Default Customer’s
Description Setting range
(channel 0) setting setting
Rated frequency V104 50 or 60 Hz 50 Hz
Time setting range for V105 0...999 min 10 min
demand values in minutes
Non-volatile memory V106 0...31 31
settings
Time setting for disabling V108 0...999 min 60 min
new trip targets on the LCD
Trip-circuit supervision V113 0 = not in use 0
1 = in use
Remote control of settings V150 0 = setting group 1 0
1 = setting group 2
Unit address of the relay V200 1...254 1
Data transfer rate (SPA), V201 9.6/4.8 9.6
kbps
Rear communication V203 0 = SPA 0
protocol 1 = IEC_103
2 = Modbus RTU
3 = Modbus ASCII
Connection type V204 0 = loop 0
1 = star
Line-idle state V205 0 = light off 0
1 = light on

155

Downloaded from www.Manualslib.com manuals search engine

 REF 610 Feeder Protection Relay 1MRS 755535

Technical Reference Manual - ANSI Version

Table 10.-3Control parameters

Parameter Default Customer’s
Description Setting range
(channel 0) setting setting
Optional communication V206 0 = not in use 0
module 1 = in use

Table 10.-4Parameters for the disturbance recorder

Parameter Default Customer’
Description Setting range
(channel 0) setting s setting
Sampling rate M15 800/960 Hz 800 Hz
400/480 Hz
50/60 Hz
Station identification/unit M18 0...9999 0
number
Name of the feeder M20 Max 16 characters - ABB -
Analogue channel M80, M81 Factor 0...65535, unit 00001,In (CT)
conversion factor and unit (A, kA), e.g. 10,kA
for la, lb and lc
Analogue channel M83 Factor 0...65535, unit 00001,In (CT)
conversion factor and unit (A, kA), e.g. 10,kA
for the ground-fault current
Internal trigger signals' V236 0...16383 682
checksum
Internal trigger signal's V237 0...16383 0
edge
Checksum of internal signal V238 0...16383 751
storing mask
Post-triggering recording V240 0...100% 50%
length
External trigger signal's V241 0...31 0
checksum
External trigger signal's V242 0...31 0
edge
Checksum of external V243 0...31 0
signal storing mask

Table 10.-5Auto-reclose parameters

Parameter Default Customer’s
Description Value
(channel 0) setting setting
CB Closing time V121 0.1...10 s 0.2 s
Pickup delay of element V122 0...300 s 300 s
51P
Pickup delay of element V123 0...300 s 300 s
51N
Reclaim time V124 3...300 s 10 s
Cutout time V125 0.1...300 s 0.1 s
Dead time of shot 1 V126 0.1...300 s 0.3 s
Dead time of shot 2 V127 0.1...300 s 30 s
Dead time of shot 3 V128 0.1...300 s 30 s
SG1 V129 0...255 0
SG2 V130 0...1023 0
SG3 V131 0...31 15

156

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 Feeder Protection Relay REF 610
Technical Reference Manual - ANSI Version

157

Downloaded from www.Manualslib.com manuals search engine

 1MRS 755535 022005 - 2.2005

ABB Oy ABB Inc

Distribution Automation Distribution Automation
P.O. Box 699 7036 Snowdrift Rd
FI-65101 Vaasa Allentown, Pa. 18106
FINLAND Phone: (610) 395-7333
Tel. +358 10 22 11 Toll Free: (800) 634-6005
Fax. +358 10 224 1094
Fax: (610) 395-1055
www.abb.com/substationautomation

Downloaded from www.Manualslib.com manuals search engine