Scribd Logo
Upload

Welcome to Scribd!

  • 37 views

    Engineering Consultants Group: Checking and Packing Hall Checked by

    Uploaded by

    Ahmed Tawfik
    1) This document provides calculations for checking and packing hall beam SB-1. It specifies beam forces, material properties, beam section properties, and checks beam design for stresses, buckling, shear, and deflection. 2) The beam is an IPE 300 rolled steel section with applied forces of 7.1 mt of bending moment and 0.7 t of shear. Calculations verify the section is compact and satisfies stress, buckling, shear, and deflection limits. 3) A second beam is then analyzed using a built-up box section, with applied forces of 4 mt bending and 2.5 t shear. Again, calculations verify this section satisfies all design checks.

    Copyright:

    © All Rights Reserved
    Download as XLS, PDF, TXT or read online from Scribd

    Engineering Consultants Group: Checking and Packing Hall Checked by

    Uploaded by

    Ahmed Tawfik
    37 views3 pages
    1) This document provides calculations for checking and packing hall beam SB-1. It specifies beam forces, material properties, beam section properties, and checks beam design for stresses, buckling, shear, and deflection. 2) The beam is an IPE 300 rolled steel section with applied forces of 7.1 mt of bending moment and 0.7 t of shear. Calculations verify the section is compact and satisfies stress, buckling, shear, and deflection limits. 3) A second beam is then analyzed using a built-up box section, with applied forces of 4 mt bending and 2.5 t shear. Again, calculations verify this section satisfies all design checks.

    Original Description:

    MX

    Original Title

    MX MEMBER

    Copyright

    © © All Rights Reserved

    Available Formats

    XLS, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    1) This document provides calculations for checking and packing hall beam SB-1. It specifies beam forces, material properties, beam section properties, and checks beam design for stresses, buckling, shear, and deflection. 2) The beam is an IPE 300 rolled steel section with applied forces of 7.1 mt of bending moment and 0.7 t of shear. Calculations verify the section is compact and satisfies stress, buckling, shear, and deflection limits. 3) A second beam is then analyzed using a built-up box section, with applied forces of 4 mt bending and 2.5 t shear. Again, calculations verify this section satisfies all design checks.

    Copyright:

    © All Rights Reserved
    Download as XLS, PDF, TXT or read online from Scribd
    Download as xls, pdf, or txt
    37 views3 pages

    Engineering Consultants Group: Checking and Packing Hall Checked by

    Uploaded by

    Ahmed Tawfik
    1) This document provides calculations for checking and packing hall beam SB-1. It specifies beam forces, material properties, beam section properties, and checks beam design for stresses, buckling, shear, and deflection. 2) The beam is an IPE 300 rolled steel section with applied forces of 7.1 mt of bending moment and 0.7 t of shear. Calculations verify the section is compact and satisfies stress, buckling, shear, and deflection limits. 3) A second beam is then analyzed using a built-up box section, with applied forces of 4 mt bending and 2.5 t shear. Again, calculations verify this section satisfies all design checks.

    Copyright:

    © All Rights Reserved
    Download as XLS, PDF, TXT or read online from Scribd
    Download as xls, pdf, or txt
    of 3

    ECG Project Name

    Job Ref.
    Engineering Consultants Group CHECKING AND PACKING HALL

    Bldg. 2, Block 10, El Sefarat District Calc. By Date Checked By Date Rev.

    P.O.Box No. 1167, Cairo 11511, Egypt. M.Nour Sheet No.


    SEC. BEAM ID :- ( SB-1 ) Refrences
    Steel grade St.37 ECP
    Fy = 2.40 t/cm2
    P (2)
    Fu = 3.60 t/cm2 P (2)
    1)- APPLIED FORCES :- Case Combination
    M = 7.10 mt a
    Q = 0.70 t

    2)- CHOISE OF SECTION :-

    The section is Rolled section IPE 300


    bFL = 150.0 mm
    tFL = 10.7 mm
    h = 300.0 mm
    tWEB = 7.1 mm

    3)- BEAM DATA :-


    Total length of Beam (L) = 5.00 m
    Lu of compressin flange = 5.00 m

    4)- CHECK SECTION :-


    PROPERTIES OF SECTION :-

    Y = 15.00 cm
    A = 53.80 cm2
    Ix = 8360.00 cm4
    Sx = 557.00 cm3
    rx = 12.50 cm
    ry = 3.35 cm

    CHECK COMPACTNESS :-
    dw/tw = 35.014 Web is Compact table(2.1a)
    C/tf = 5.276 Flange is Compact table(2.1c)
    The sec is Compact

    CHECK NORMAL STRESSES :-


    Cb = 1.13 table(2.2)
    ( 20.bf ) / (√ fy ) = 1.936 m ECP 16
    Lumax = 1.936 m
    ( 1380.Af ) / ( fy.d ) x Cb = 3.48 m eqn. 2.18
    Lateral torsional buckling of comp.flange There is LTB
    Fltb = 1.275 t/cm2
    Fbcx = 1.275 t/cm2
    fbcx = 1.275 t/cm2 < 1.275 SAFE

    CHECK SHEAR STRESSES :-


    qw = 0.04 t/cm2 < 0.840 SAFE eqn. 2.2

    CHECK DEFLICTION DUO TO LIVE LOAD :-


    WL.L = 0.30 t/m
    Beam type = simple
    δL.L = 0.139 cm < 1.67 SAFE ECP 132
    ECG Project Name
    Job Ref.
    Engineering Consultants Group CHECKING AND PACKING HALL

    Bldg. 2, Block 10, El Sefarat District Calc. By Date Checked By Date Rev.

    P.O.Box No. 1167, Cairo 11511, Egypt. M.Nour Sheet No.


    table(9.1)
    ECG Project Name
    Job Ref.
    Engineering Consultants Group CHECKING AND PACKING HALL

    Bldg. 2, Block 10, El Sefarat District Calc. By Date Checked By Date Rev.

    P.O.Box No. 1167, Cairo 11511, Egypt. M.Nour Sheet No.


    SEC. BEAM ID :- ( SB-1 ) Refrences
    Steel grade St.37 ECP
    Fy = 2.40 t/cm2 P (2)
    Fu = 3.60 t/cm2 P (2)
    1)- APPLIED FORCES :- Case Combination
    M = 4.00 mt a
    Q = 2.50 t

    2)- CHOISE OF SECTION :-

    The section is Built up section


    bFLU = 250.00 mm The Comprision flange is bFLU
    tFLU = 18.00 mm
    hWeb = 200.00 mm
    tWeb = 6.00 mm
    bFLL = 250.00 mm
    tFLL = 18.00 mm

    3)- BEAM DATA :-


    Total length of Beam (L) = 2.00 m
    Lu of compressin flange = 10.00 m

    4)- CHECK SECTION :-


    PROPERTIES OF SECTION :-

    Y = 11.80 cm
    A = 102.00 cm2
    Ix = 11117.20 cm4
    Sx.top = 942.14 cm3
    Sx.bot = 942.14 cm3

    CHECK COMPACTNESS :-
    dw/tw = 33.333 Web is Compact table(2.1a)
    C/tf = 6.778 Flange is Compact table(2.1c)
    The sec is Compact

    CHECK NORMAL STRESSES :-


    Cb = 1.30 table(2.2)
    ( 20.bf ) / (√ fy ) = 3.227 m ECP 16
    Lumax = 3.227 m
    ( 1380.Af ) / ( fy.d ) x Cb = 16.82 m eqn. 2.18
    Lateral torsional buckling of comp.flange There is LTB
    Fltb = 1.392 t/cm2
    Fbcx = 1.392 t/cm2
    fbcx = 0.425 t/cm2 < 1.392 SAFE

    CHECK SHEAR STRESSES :-


    qw = 0.21 t/cm2 < 0.840 SAFE eqn. 2.2

    CHECK DEFLICTION DUO TO LIVE LOAD :-


    WL.L = 1.50 t/m
    Beam type = simple
    δL.L = 0.013 cm < 0.67 SAFE ECP 132
    table(9.1)

    You might also like