1X5X3 WITH 1.5m Cast-In-situ

Project: CONSTRUCTION OF ACCESS CONTROLLED NAGPUR - MUMBAI SUPER COMMUNICATION EXPRESSWAY
(MAHARASHTRA SAMRUDDHI MAHAMARG) IN THE STATE OF MAHARASHTRA ON EPC MODE FOR PACKAGE 06, FROM
KM. 259.900 TO KM. 296.000, (Section- Village Belgaon to Village Parda) in District Buldhana
Design note of BOX CULVERT @ KM 279+272 (Single cell box type) of size 5 m x
Title:
3 m with1.04m earthcushion, 0.310 PQC, 0.150 DLC (total cushion 1.5m)
279+272
MAHARASHTRA STATE ROAD DEVELOPMENT

CLIENT
CORPORATION LTD. (MSRDC)
R0 21-01-2019 Design of Box Culvert

Rev Date Description
Design consultant :
CIVIL MANTRA INFRACON PRIVATE LIMITED
Index
S.NO. DESCRIPTION Page No
1.0 Introduction 3
2.0 Dimension of Box 4
3.0 Basic input data 5
4.0 Idealised Structure for Staad Analysis 6
5.0 Load Calculation 7-16
6.0 STAAD input file 17-36
7.0 Summary of Design Moments 37-38
8.0 Design of Top Slab 39-42
9.0 Design of Bottom slab 43-47
10.0 Design of outer wall 48-55
12.0 Summary of reinforcement provided 64-65
13.0 Base pressure check 66

1.0 Introduction
Design note of BOX CULVERT @ KM 279+272 (Single cell box type) of size 5 m x 3 m with1.04m
earthcushion, 0.310 PQC, 0.150 DLC (total cushion 1.5m)
1.2 Design Basis
All the Loads are calculated based on IRC : 6 and design has been done based on IRC : 112 - 2011.
Structure has been analysed as a box section resting over a series of soil springs with stiffness
being considered depending on SBC of soil and allowable settlement.
The Structure is modelled as two dimensional centre line model, All other inputs are given with
load combinations as per IRC 6 and the results thus obtained for various members at different
locations are extracted for design in Ultimate limit state and checked for serviceability limit state.
For crack width check quasi permanent load combinations have been used.
1.3 Reference documents :-
a) IRC 6 d) Specialised literature as relevant

b) IRC 21 e) IRC 112-2011
c) IRC 78
1.4 Loads has been adopted as per IRC-6
a) Dead load -Self weight command is assigned to all members for calculating the dead load of the structure
b) Superimposed dead load-As structure is analyze for unit width, 0.5m width is considered for
crash barrier/railing.
c) Earth Pressure-The earth pressure at rest has been applied on walls reatining earth as structure
is not free to deform.
d) Live load - 70R Wheel ,70R Tracked, 40 T Boggie load considered using effective width method
given in clause B 3.2 of Annexure 3 of IRC 112.
e) Live load Surcharge-The Live load surcharge equivalent to 1.2m fill has been applied on walls
reatining earth.
f) Temperature- Linear & gradient both temperatur case has been considered as per clause 215 of IRC 6:2017.
h) Cushion/fill load (if any) is considered as dead load.
i) Impact factor considered for live load (Clause 208.3 of IRC:6-2017) = 1.25.
1.5 Load cases considered:

Load combination as per IRC - 6 : 2017 have been considered in STAAD model.
2.0 Dimension of Box
No. of Cells 1 No.
Clear Depth 3.00 m
Clear Span 1 Ministry of Road Transport and Highway 5.00 m
Top slab thickNess 0.350 m
Bottom slab thickNess 0.400 m
ThickNess of Outer Wall 0.400 m

1.040
0.350
0.350
3.000 0.15
0.15
#N/A 3.00
3.75
0.400
0.400
5.00
0.400
0.400
5.800
3.375 5.400
Idealised Structure for Staad Analysis
The Structure is modeled using STAAD as a plane frame in X-Y plane of unit (1m) width.
3.0 Basic Input Data
Skew angle 0.00 degree

Free board Ministry of Road Transport and Highway 0.300 m
No of cells 1
Clear span 5.00 m
Clear Height 3.00 m
Water Height 2.70 m
Top slab thickNess 0.350 m
Bottom slab thickNess 0.400 m
Side wall thickNess 0.400 m
Haunch Size 0.15 X 0.15 m
Total width of deck slab 47.50 m
ThickNess of wearing coat 0.460 m
Carriageway 44.50 m
Crash barrier width/Parapet 0.50 m
Imapact factor 1.25
Basic Parameters
Concrete Grade 30 Mpa
Steel Grade 500.00 Mpa
Co-efficient of earth pressure at rest 0.50
Co-efficient of active earth pressure 0.279
БSc (Concrete) 10.00 MPa
БSt (Steel) 435 Mpa
Modular ratio 9.33
Net Safe Bearing pressure (As per geotechnical report) 120 kN/m2
Earth cushion 1.04 m
Live load Surcharge 1.20
Unit Weight
Unit weight of concrete 25.00 kN/m3
Unit weight of earth 20.00 kN/m3
Unit weight of water 10.00 kN/m3
Unit Weight of Wearing Coat/PQC,DLC 24.00 kN/m3
4.0 Idealised Structure for Staad Analysis
The Structure is modeled using STAAD as a plane frame in X-Y plane of unit (1m) width.
The structural model is shown in figure 2.0.
Ministry of Road Transport and Highway
8
8
4
3.375 5.400 0.000 3
0.5
Figure-C/L of Box
a) Material properties:-
Density Modulus E Posion

Material Grade
(kg/m^3) kN/mm^2 ratio(v)
Conrete M-30 2500 31 0.20
Steel Fe-500 7850 200 0.30
Nos of beam for one span at bottom = 10 Nos.

Spacing between support = 0.540 m
Modulus of Subgrade Reaction = 1600 kN/m3
Spring constant at intermediate support = 864 kN/m
Spring constant at end support = 432 kN/m
1.2
b) Number of Load Cases 23
c) Load combination 296
5.0 Load Calculation
5.1 Dead load Calucations on top slab (DL)

a) Weight of wearing coat = 0.46*24 11.04 kN/m2
b) Self Weight of slab = 0.35*25 8.75 kN/m2
c) Weight of Crash Barrier/Parapet = 0.36*25 9.00 kN/m2
d) Dead weight due earth fill = 1.04*20 20.80 kN/m2
5.2 Side Wall Loads :
Earth presuure is applied as linearly varying load on each member. The model is centre line model,
so the resultant force and moment caused due to earth pressure between outer face
of slab and centre line are applied as nodal loads on the corresponding nodes.
5.2.1 Active Earth Pressure Height
5.80 Kn/m2 1.04 m Top of Slab

6.78 Kn/m2 1.22 m Cg of Top Slab
23.52 Kn/m2 4.22 m Cg of Wall
24.64 Kn/m2 4.42 m Cg of Base Slab

25.75 Kn/m2 4.62 m Base Slab Bottom
Earth pressure at rest (Dry conditions) =0.5*(3+0.35/2+0.4/2+1.04)*20

= 44.150
Earth pressure at rest (HFL conditions) =0.5*(3+0.35/2+0.4/2+1.04)*(20-10)
+10*(3+0.35/2+0.4/2+1.04)*0
2
= 22.075 kN/m
Active Earth pressure (Dry conditions) =0.279*(3+0.35/2+0.4/2+1.04)*20
2
= 27.203 kN/m
Active Earth pressure (HFL conditions) =0.279*(3+0.35/2+0.4/2+1.04)*(20-10)
+10*(3+0.35/2+0.4/2+1.04)*0
= 12.318 kN/m2
5.2.2 Live Load Surcharge
Earth Pressure at base due to live load surcharge = 0.5*20*1.2

2
(1.2m surcharge) at rest = 12.00 kN/m
Earth Pressure at base due to live load surcharge = 0.279*20*1.2

2
(1.2m surcharge) active earth pressure conditions = 6.696 kN/m
Earth Pressure at base due to live load surcharge =0.279*(20-10)*1.2+10*1.2*0

(1.2m surcharge) active earth pressure conditions(HFL) = 3.348 kN/m2
5.3 Dead load on base slab due to water =10*2.7

2
= 27.000 kN/m
5.5 Live Load on Top slab
A) 70 R (Tracked on Midspan)
Direction of Traffic
b = 47.50 m
8
0.84 8
4
3
350 Kn 350 Kn
4.57 lo = 5.00 m
0.5
2.12 2.06
Total Load= 700 Kn 8.27 m 5.00 m

140.00 Kn/m
Effective width of Loading
a = 2.50 m
b1 = 3.84 m
b/lo = 9.50
α = 2.60
beff = 7.09 m
2.06 m < 7.09 m
Therefore overlaping due to load dispersion occurs.
Effective width = 7.73 m

Width along span = 5.00 m
Load intensity = 18.12 Kn/m2
Increase due to impact = 22.65 Kn/m2
Say = 22.70 Kn/m2
B) 70 R (Tracked at support)

140.00 Kn/m 12
Effective width of Loading = 0.279*20*1.2
a = 2.29 m
b1 = 3.84 m
b/lo = 9.50
α = 2.60
beff = 7.07 m
2.06 m < 7.07 m

Say = 22.70 Kn/m2
C) 40 T (Boggie load on Midspan)
Direction of Traffic
b = 47.50 m
0.86
0.22
100 Kn 100 Kn
100 Kn 100 Kn 1.22 lo = 5.00 m
2.13 1.93
40 T (Boggie load midspan)

80.00 Kn/m
a = 2.50 m
b1 = 3.86 m
b/lo = 9.50
α = 2.60
beff = 7.11 m
1.93 m < 7.11 m

Say = 12.80 Kn/m2
D) 40 T (Boggie load at support)

121.58 Kn/m
a = 0.61 m
b1 = 3.86 m
b/lo = 9.50
α = 2.600
beff = 5.25 m
1.93 m < 5.25 m

Say = 22.70 Kn/m2
E) 70R Wheel Case 1
12 12 17 17 17 17
1.52 2.13 1.37 3.05m 1.37m 0.86m 1.93m 0.86m
2.50m
Width along span = 3.920m
S.No. Load a a beff Overlap Eff. Width Load Int. With Imp.
1 166.77 1.96m 2.60 6.96m Yes 7.54m 5.6 kN/sqm 7 kN/sqm
0 0 0.00m 0.00 0.00m No 0.00m 0.0 kN/sqm 0 kN/sqm
F) 70R Wheel Case 2
12 12 17 17 17 17
1.52 1.5 1.37 3.05m

2.13 1.37
2.70m
1 166.77 2.015 2.60 6.99m Yes 7.55m 5.6 kN/sqm 7 kN/sqm
0 0 0.000 0.00 0.00m No 0.00m 0.0 kN/sqm 0 kN/sqm
0 0 0.000 0.00 0.00m No 0.00m 0.0 kN/sqm 0 kN/sqm
0 0 0.000 0.00 0.00m No 0.00m 0.0 kN/sqm 0 kN/sqm
0 0 0.000 0.00 0.00m No 0.00m 0.0 kN/sqm 0 kN/sqm
G)70R Wheel Case 3
12 12 17 17 17 17
1.52
1.52 2.13
2.13 1.37
1.37 3.05m
3.05m 1.37m
1.37
2.70m
0 0 0.000 0.00 0.00m No 0.00m 0.0 kN/sqm 0 kN/sqm
0 0 0.000 0.00 0.00m No 0.00m 0.0 kN/sqm 0 kN/sqm
0 0 0.000 0.00 0.00m No 0.00m 0.0 kN/sqm 0 kN/sqm
H) SV LOADING Case 1
18 18 18 18 18 18 0.156 3.156
1.5 1.5 1.5 1.5m 1.5 m 1.5 m 0.274m 1.2000m 0.274m
2.50m
I) SV LOADING CASE 2
18 18 18 18 18 18
1.5 1.5 1.5 1. 1.5m 1.5m
2.70m
0 0 0.000 0.00 0.00m No 0.00m 0.0 kN/sqm 0 kN/sqm
0 0 0.000 0.00 0.00m No 0.00m 0.0 kN/sqm 0 kN/sqm
0 0 0.000 0.00 0.00m No 0.00m 0.0 kN/sqm 0 kN/sqm
J) SV LOADING CASE 3
18 18 18 18 18 18
1.52
1.5 2.13
1.5 1.5
1.37 1.5m
3.05m 1.37m
1.5m
2.70m
0 0 0.000 0.00 0.00m No 0.00m 0.0 kN/sqm 0 kN/sqm
0 0 0.000 0.00 0.00m No 0.00m 0.0 kN/sqm 0 kN/sqm
0 0 0.000 0.00 0.00m No 0.00m 0.0 kN/sqm 0 kN/sqm
0 0 0.000 0.00 0.00m No 0.00m 0.0 kN/sqm 0 kN/sqm
H) Braking load 20% Av. Eff. Width Load per meter

Load on the span 70R Wheel 0 kN 0 kN 7.55m 0 kN/m
Load on the span 40T 0 kN 0 kN 6.69m 0 kN/m
Load on the span 70R Track 0 kN 0 kN 7.73m 0 kN/m
Load on the span sv loading 0 kN 0 kN 5.81m 0 kN/m
Max. force 0 kN/m
5.6 Calculation for Temperature Load ( IRC : 6 - 2017 )
Maximum air shade temperature 47.5 °C

Minimum air shade temperature 3.75 °C
Mean of max and min temperature 25.625 °C
Temperature Rise 35.625 °C
Temperature fall 15.625 °C
+/- 0
Temperature force 2698.92 kN
Effect of temperature Gradient
The Box has been checked for temperature differential
F= Ec*a*Dt*A
Ec= Modulus of Elasticity of concrete 3.21E+06 t/m^2
a= Coefficient of thermal expansion 1.20E-05 /° C (as per IRC 6)
Dt= Temperature Differential
A= X sectional area of of section where temperature
differential is Dt
Average Thickness of Deck 350 mm
Effect of temperature rise:

#N/A
4 13.8
0.11 m 1 2
3
0.11 m
0.35 m
0.04 m
1.2
23
0.11 m 4
2.1
Sr. no. Dt b t A=bxt F(force) Acting at Eccentricity Moment
m m sqm kN m m kN-m
1 4.00 1.00 0.105 0.105 161.935 0.053 0.123 19.837
2 6.90 1.00 0.105 0.105 279.338 0.035 0.140 39.107
3 2.00 1.00 0.105 0.105 80.968 0.140 0.035 2.834
4 1.05 1.00 0.105 0.105 42.508 0.315 -0.140 -5.951
SF 564.749 Moment 55.827
= 0.279*20*1.2
Effect of temperature drop:
9.9 0.7
2
1 0.07 m
3
0.09 m
0.35 m
0.04 m
0.09 m
6
5 0.07 m
4
5.8 0.8
Acting at
Sr. no. Dt b t A=bxt F(force) Eccentricity e Moment
from top
m m sqm kN m m kN-m
1 0.70 1.00 0.070 0.070 18.892 0.035 0.140 2.645
2 4.95 1.00 0.070 0.070 133.597 0.023 0.152 20.262
3 0.35 1.00 0.088 0.088 11.808 0.099 0.076 0.895
4 2.90 1.00 0.070 0.070 78.269 0.327 -0.152 -11.871
5 0.80 1.00 0.070 0.070 21.591 0.315 -0.140 -3.023
6 0.40 1.00 0.088 0.088 13.495 0.251 -0.076 -1.023
SF 277.651 Moment 7.886
6.0 STAAD input file
Ministry of Road Transport and Highway
STAAD SPACE
INPUT WIDTH 79
UNIT METER KN
JOINT COORDINATES
1000
2 0 3.375 0
3 5.4 3.375 0
4 5.4 0 0
5 0.54 0 0
6 1.08 0 0
7 1.62 0 0
8 2.16 0 0
9 2.7 0 0
10 3.24 0 0
11 3.78 0 0
12 4.32 0 0
13 4.86 0 0
MEMBER INCIDENCES
112
223
334
415
556
667
778
889
9 9 10
10 10 11
11 11 12
12 12 13
13 13 4
***********************************
DEFINE MATERIAL START
ISOTROPIC CONCRETE
E 31000000
POISSON 0.17
DENSITY 25
ALPHA 1e-005
DAMP 0.05
END DEFINE MATERIAL
CONSTANTS
MATERIAL CONCRETE ALL
MEMBER PROPERTY INDIAN
2 PRIS YD 0.35 ZD 1
1 3 PRIS YD 0.4 ZD 1
4 to 13 PRIS YD 0.4 ZD 1
SUPPORTS
1 FIXED BUT MX MY MZ KFY 432
5 TO 13 FIXED BUT MX MY MZ KFY 864
4 FIXED BUT MX MY MZ KFY 432
********************************************
***DL***
LOAD 1 LOADTYPE Dead TITLE DEAD LOAD
SELFWEIGHT Y -1 LIST ALL
***DL HFL CASE***
LOAD 2 LOADTYPE Dead TITLE DEAD LOAD (HFL)
SELFWEIGHT Y -1 LIST 2
SELFWEIGHT Y -0.85 LIST 1 3 TO 13
***SIDL+ Earth Fill****
LOAD 3 LOADTYPE Dead TITLE SIDL+ EARTH FILL
MEMBER LOAD
2 UNI GY -9
2 UNI GY -20.8
**Surfacing (wearing coat)
LOAD 4 LOADTYPE Dead TITLE WEARING COAT
MEMBER LOAD
2 UNI GY -11.04
****ACTIVE EARTH PRESSURE ****
LOAD 5 LOADTYPE None TITLE EARTH PRESSURE NORMAL CONDITION
MEMBER LOAD
3 TRAP GX -6.7797 -27.2025
1 TRAP GX 27.2025 6.7797
LOAD 6 LOADTYPE None TITLE LL SURCHARGE NORMAL CONDITIONS
MEMBER LOAD
3 UNI GX -6.696
1 UNI GX 6.696
LOAD 7 LOADTYPE None TITLE HFL EARTH PRESSURE
MEMBER LOAD
3 TRAP GX -3.38985 -12.31785
1 TRAP GX 12.31785 3.38985
LOAD 8 LOADTYPE None TITLE HFL LL SURCHARGE
MEMBER LOAD
3 UNI GX -3.348
1 UNI GX 3.348
LOAD 9 LOADTYPE None TITLE EARTH PRESSURE AT REST
MEMBER LOAD
3 TRAP GX -12.15 -44.15
1 TRAP GX 44.15 12.15
LOAD 10 LOADTYPE None TITLE HFL EARTH PRESSURE AT REST
MEMBER LOAD
3 TRAP GX -6.075 -22.075
1 TRAP GX 22.075 6.075
LOAD 11 WT. OF WATER ON BOTTOM SLAB
MEMBER LOAD
4 TO 13 UNI GY -27
3 TRAP GX 0 27 0.475
1 TRAP GX -27 0 0 2.9
****CLASS 70R (TOP SLAB AT MID SPAN)*******
LOAD 12 CLASS 70R (TOP SLAB AT MID SPAN)
JOINT LOAD
2 FX 0
MEMBER LOAD
2 UNI GY -22.7 0.2 5.2
******CLASS 40T (TOP SLAB AT MID SPAN)*********
LOAD 13 CLASS 40T (TOP SLAB AT MID SPAN)
JOINT LOAD
2 FX 0
MEMBER LOAD
2 UNI GY -12.8 0.13 5.27
******CLASS 40T AT SUPPORT (TOP SLAB AT SUPP.)*********
LOAD 14 CLASS 40T AT SUPPORT (TOP SLAB AT SUPP.)
JOINT LOAD
2 FX 0
MEMBER LOAD
2 UNI GY -22.7 0 3.29
******CLASS 70R AT SUPPORT (TOP SLAB AT SUPP.)**
LOAD 15 CLASS 70R AT SUPPORT (TOP SLAB AT SUPP.)
JOINT LOAD
2 FX 0
MEMBER LOAD
2 UNI GY -22.7 0 5
****CLASS 70R Wheel Case 1(TOP SLAB AT SUPPORT)*******
LOAD 16 CLASS 70R WHEEL CASE 1
JOINT LOAD
2 FX 0
MEMBER LOAD
2 UNI GY -7.05 0 3.92
2 UNI GY -7.03 1.37 5.29
**
**
**
**
**
****CLASS 70R Wheel Case 2(TOP SLAB AT MID SPAN)*******
JOINT LOAD
2 FX 0
MEMBER LOAD
2 UNI GY -7.04 0.055 3.975
2 UNI GY -7.04 1.425 5.345
**
**
**
**
**
****CLASS 70R Wheel Case 3(TOP SLAB AT MID SPAN)*******
JOINT LOAD
2 FX 0
MEMBER LOAD
2 UNI GY -7.05 0 3.92
2 UNI GY -7.03 1.37 5.29
**
**
**
**
**
LOAD 23 SV LOADING CASE 1
JOINT LOAD
2 FX 0
MEMBER LOAD
2 UNI GY -7.2 0 3.974
2 UNI GY -7.22 1.5 5.4
2 UNI GY -8.7 3 5.4
**
**
**
**
****SV LOADING Case 2(TOP SLAB AT MID SPAN)*******
JOINT LOAD
2 FX 0
MEMBER LOAD
2 UNI GY -7.2 0 3.974
2 UNI GY -7.22 1.5 5.4
2 UNI GY -10.87 3 5.4
**
**
**
**
****SV LOADING Case 3(TOP SLAB AT MID SPAN)*******
JOINT LOAD
2 FX 0
MEMBER LOAD
2 UNI GY -7.2 0 3.974
**
**
**
**
LOAD 19 TEMPERATURE LOADING (RISE)
TEMPERATURE LOAD
2 TEMP 0
*********Uniform decrease****
LOAD 20 TEMPERATURE LOADING (FALL)
TEMPERATURE LOAD
2 TEMP 0
***********Temperature gradient
LOAD 21 TEMPERATURE GRADIENT (RISE)
JOINT LOAD
2 FX -0
3 FX 0
2 MZ 0
3 MZ -0
LOAD 22 TEMPERATURE GRADIENT (FALL)
JOINT LOAD
2 FX 0
3 FX -0
2 MZ -0
3 MZ 0
*Partial Safety for Verification of Structural Strength (Basic Combination)
LOAD COMBINATION 26 BASIC COMBINATION EARTH PRESSURE AS A LEADING LOAD
1 1.35 3 1.35 4 1.75 5 1.5 6 1.2 12 1.15 19 1.5 21 1.5 11 1
1 1.35 3 1.35 4 1.75 5 1.5 6 1.2 13 1.15 19 1.5 21 1.5 11 1
1 1.35 3 1.35 4 1.75 5 1.5 6 1.2 14 1.15 19 1.5 21 1.5 11 1
1 1.35 3 1.35 4 1.75 5 1.5 6 1.2 15 1.15 19 1.5 21 1.5 11 1
1 1.35 3 1.35 4 1.75 5 1.5 6 1.2 16 1.15 19 1.5 21 1.5 11 1
1 1.35 3 1.35 4 1.75 5 1.5 6 1.2 17 1.15 19 1.5 21 1.5 11 1
1 1.35 3 1.35 4 1.75 5 1.5 6 1.2 18 1.15 19 1.5 21 1.5 11 1
1 1.35 3 1.35 4 1.75 5 1.5 6 1.2 23 1 19 1.5 21 1.5 11 1
1 1.35 3 1.35 4 1.75 5 1.5 6 1.2 24 1 19 1.5 21 1.5 11 1
1 1.35 3 1.35 4 1.75 5 1.5 6 1.2 25 1 19 1.5 21 1.5 11 1
LOAD COMBINATION 36 BASIC COMBINATION LIVE LOAD AS A LEADING LOAD
1 1.35 3 1.35 4 1.75 5 1 6 1.2 12 1.5 20 1.5 22 1.5
1 1.35 3 1.35 4 1.75 5 1 6 1.2 13 1.5 20 1.5 22 1.5
1 1.35 3 1.35 4 1.75 5 1 6 1.2 14 1.5 20 1.5 22 1.5
1 1.35 3 1.35 4 1.75 5 1 6 1.2 15 1.5 20 1.5 22 1.5
1 1.35 3 1.35 4 1.75 5 1 6 1.2 16 1.5 20 1.5 22 1.5
1 1.35 3 1.35 4 1.75 5 1 6 1.2 17 1.5 20 1.5 22 1.5
1 1.35 3 1.35 4 1.75 5 1 6 1.2 18 1.5 20 1.5 22 1.5
1 1.35 3 1.35 4 1.75 5 1 6 1.2 23 1 20 1.5 22 1.5
1 1.35 3 1.35 4 1.75 5 1 6 1.2 24 1 20 1.5 22 1.5
1 1.35 3 1.35 4 1.75 5 1 6 1.2 25 1 20 1.5 22 1.5
LOAD COMBINATION 46 BASIC COMBINATION STR. AT REST
1 1.35 3 1.35 4 1.75 9 1.5
*HFL Partial Safety for Verification of Structural Strength (Basic Combination)
2 1.35 3 1.35 4 1.75 7 1.5 8 1.2 12 1.15 11 1 19 1.5 21 1.5
2 1.35 3 1.35 4 1.75 7 1.5 8 1.2 13 1.15 11 1 19 1.5 21 1.5
2 1.35 3 1.35 4 1.75 7 1.5 8 1.2 14 1.15 11 1 19 1.5 21 1.5
2 1.35 3 1.35 4 1.75 7 1.5 8 1.2 15 1.15 11 1 19 1.5 21 1.5
2 1.35 3 1.35 4 1.75 7 1.5 8 1.2 16 1.15 11 1 19 1.5 21 1.5
2 1.35 3 1.35 4 1.75 7 1.5 8 1.2 17 1.15 11 1 19 1.5 21 1.5
2 1.35 3 1.35 4 1.75 7 1.5 8 1.2 18 1.15 11 1 19 1.5 21 1.5
2 1.35 3 1.35 4 1.75 7 1.5 8 1.2 23 1 11 1 19 1.5 21 1.5
2 1.35 3 1.35 4 1.75 7 1.5 8 1.2 24 1 11 1 19 1.5 21 1.5
2 1.35 3 1.35 4 1.75 7 1.5 8 1.2 25 1 11 1 19 1.5 21 1.5
2 1.35 3 1.35 4 1.75 7 1 8 1.2 12 1.5 11 1 20 1.5 22 1.5
2 1.35 3 1.35 4 1.75 7 1 8 1.2 13 1.5 11 1 20 1.5 22 1.5
2 1.35 3 1.35 4 1.75 7 1 8 1.2 14 1.5 11 1 20 1.5 22 1.5
2 1.35 3 1.35 4 1.75 7 1 8 1.2 15 1.5 11 1 20 1.5 22 1.5
2 1.35 3 1.35 4 1.75 7 1 8 1.2 16 1.5 11 1 20 1.5 22 1.5
2 1.35 3 1.35 4 1.75 7 1 8 1.2 17 1.5 11 1 20 1.5 22 1.5
2 1.35 3 1.35 4 1.75 7 1 8 1.2 18 1.5 11 1 20 1.5 22 1.5
2 1.35 3 1.35 4 1.75 7 1 8 1.2 23 1 11 1 20 1.5 22 1.5
2 1.35 3 1.35 4 1.75 7 1 8 1.2 24 1 11 1 20 1.5 22 1.5
2 1.35 3 1.35 4 1.75 7 1 8 1.2 25 1 11 1 20 1.5 22 1.5
2 1.35 3 1.35 4 1.75 10 1.5 11 1
*Partial Safety for Verification of Structural Strength (Basic Combination)
1 1.35 3 1.35 4 1.75 5 1.5 19 1.5 21 1.5
1 1.35 3 1.35 4 1.75 5 1.5 19 1.5 21 1.5
1 1.35 3 1.35 4 1.75 5 1.5 19 1.5 21 1.5
1 1.35 3 1.35 4 1.75 5 1.5 19 1.5 21 1.5
1 1.35 3 1.35 4 1.75 5 1.5 19 1.5 21 1.5
1 1.35 3 1.35 4 1.75 5 1.5 19 1.5 21 1.5
1 1.35 3 1.35 4 1.75 5 1.5 19 1.5 21 1.5
1 1.35 3 1.35 4 1.75 5 1 20 1.5 22 1.5
1 1.35 3 1.35 4 1.75 5 1 20 1.5 22 1.5
1 1.35 3 1.35 4 1.75 5 1 20 1.5 22 1.5
1 1.35 3 1.35 4 1.75 5 1 20 1.5 22 1.5
1 1.35 3 1.35 4 1.75 5 1 20 1.5 22 1.5
1 1.35 3 1.35 4 1.75 5 1 20 1.5 22 1.5
1 1.35 3 1.35 4 1.75 5 1 20 1.5 22 1.5
1 1.35 3 1.35 4 1.75 9 1.5
*HFL Partial Safety for Verification of Structural Strength (Basic Combination)
2 1.35 3 1.35 4 1.75 7 1.5 11 1 19 1.5 21 1.5
2 1.35 3 1.35 4 1.75 7 1.5 11 1 19 1.5 21 1.5
2 1.35 3 1.35 4 1.75 7 1.5 11 1 19 1.5 21 1.5
2 1.35 3 1.35 4 1.75 7 1.5 11 1 19 1.5 21 1.5
2 1.35 3 1.35 4 1.75 7 1.5 11 1 19 1.5 21 1.5
2 1.35 3 1.35 4 1.75 7 1.5 11 1 19 1.5 21 1.5
2 1.35 3 1.35 4 1.75 7 1.5 11 1 19 1.5 21 1.5
2 1.35 3 1.35 4 1.75 7 1 11 1 20 1.5 22 1.5
2 1.35 3 1.35 4 1.75 7 1 11 1 20 1.5 22 1.5
2 1.35 3 1.35 4 1.75 7 1 11 1 20 1.5 22 1.5
2 1.35 3 1.35 4 1.75 7 1 11 1 20 1.5 22 1.5
2 1.35 3 1.35 4 1.75 7 1 11 1 20 1.5 22 1.5
2 1.35 3 1.35 4 1.75 7 1 11 1 20 1.5 22 1.5
2 1.35 3 1.35 4 1.75 7 1 11 1 20 1.5 22 1.5
2 1.35 3 1.35 4 1.75 10 1.5 11 1
*Partial Safety for Verification of Serviceability Limit State (Accidental Combination)
LOAD COMBINATION 98 LL AS LEADING LOAD
1 1 3 1 4 1 5 1 6 0.2 12 0.75 19 0.5 21 0.5
1 1 3 1 4 1 5 1 6 0.2 13 0.75 19 0.5 21 0.5
1 1 3 1 4 1 5 1 6 0.2 14 0.75 19 0.5 21 0.5
1 1 3 1 4 1 5 1 6 0.2 15 0.75 19 0.5 21 0.5
1 1 3 1 4 1 5 1 6 0.2 16 0.75 19 0.5 21 0.5
1 1 3 1 4 1 5 1 6 0.2 17 0.75 19 0.5 21 0.5
1 1 3 1 4 1 5 1 6 0.2 18 0.75 19 0.5 21 0.5
1 1 3 1 4 1 5 1 6 0.2 23 0.75 19 0.5 21 0.5
1 1 3 1 4 1 5 1 6 0.2 24 0.75 19 0.5 21 0.5
1 1 3 1 4 1 5 1 6 0.2 25 0.75 19 0.5 21 0.5
1 1 3 1 4 1 5 1 6 0.2 12 0.75 20 0.5 22 0.5
1 1 3 1 4 1 5 1 6 0.2 13 0.75 20 0.5 22 0.5
1 1 3 1 4 1 5 1 6 0.2 14 0.75 20 0.5 22 0.5
1 1 3 1 4 1 5 1 6 0.2 15 0.75 20 0.5 22 0.5
1 1 3 1 4 1 5 1 6 0.2 16 0.75 20 0.5 22 0.5
1 1 3 1 4 1 5 1 6 0.2 17 0.75 20 0.5 22 0.5
1 1 3 1 4 1 5 1 6 0.2 18 0.75 20 0.5 22 0.5
1 1 3 1 4 1 5 1 6 0.2 23 0.75 20 0.5 22 0.5
1 1 3 1 4 1 5 1 6 0.2 24 0.75 20 0.5 22 0.5
1 1 3 1 4 1 5 1 6 0.2 25 0.75 20 0.5 22 0.5
LOAD COMBINATION 118 THERMAL AT REST CONDITIONS
1 1 3 1 4 1 9 1 19 0.5 21 0.5
1 1 3 1 4 1 9 1 20 0.5 22 0.5
* HFL Partial Safety for Verification of Serviceability Limit State (Accidental Combination)
2 1 3 1 4 1 7 1 8 0.2 12 0.75 19 0.5 21 0.8 11 1
2 1 3 1 4 1 7 1 8 0.2 13 0.75 19 0.5 21 0.8 11 1
2 1 3 1 4 1 7 1 8 0.2 14 0.75 19 0.5 21 0.8 11 1
2 1 3 1 4 1 7 1 8 0.2 15 0.75 19 0.5 21 0.8 11 1
2 1 3 1 4 1 7 1 8 0.2 16 0.75 19 0.5 21 0.8 11 1
2 1 3 1 4 1 7 1 8 0.2 17 0.75 19 0.5 21 0.8 11 1
2 1 3 1 4 1 7 1 8 0.2 18 0.75 19 0.5 21 0.8 11 1
2 1 3 1 4 1 7 1 8 0.2 23 0.75 19 0.5 21 0.8 11 1
2 1 3 1 4 1 7 1 8 0.2 24 0.75 19 0.5 21 0.8 11 1
2 1 3 1 4 1 7 1 8 0.2 25 0.75 19 0.5 21 0.8 11 1
2 1 3 1 4 1 7 1 8 0.2 12 0.75 20 0.5 22 0.8 11 1
2 1 3 1 4 1 7 1 8 0.2 13 0.75 20 0.5 22 0.8 11 1
2 1 3 1 4 1 7 1 8 0.2 14 0.75 20 0.5 22 0.8 11 1
2 1 3 1 4 1 7 1 8 0.2 15 0.75 20 0.5 22 0.8 11 1
2 1 3 1 4 1 7 1 8 0.2 16 0.75 20 0.5 22 0.8 11 1
2 1 3 1 4 1 7 1 8 0.2 17 0.75 20 0.5 22 0.8 11 1
2 1 3 1 4 1 7 1 8 0.2 18 0.75 20 0.5 22 0.8 11 1
2 1 3 1 4 1 7 1 8 0.2 23 0.75 20 0.5 22 0.8 11 1
2 1 3 1 4 1 7 1 8 0.2 24 0.75 20 0.5 22 0.8 11 1
2 1 3 1 4 1 7 1 8 0.2 25 0.75 20 0.5 22 0.8 11 1
2 1 3 1 4 1 10 1 19 0.5 21 0.5 11 1
2 1 3 1 4 1 10 1 20 0.5 22 0.5 11 1
*Partial Safety for Verification of Serviceability Limit State (Rare Combination)
1 1 3 1 4 1 5 1 6 0.8 12 1 19 0.8 21 0.8
1 1 3 1 4 1 5 1 6 0.8 13 1 19 0.8 21 0.8
1 1 3 1 4 1 5 1 6 0.8 14 1 19 0.8 21 0.8
1 1 3 1 4 1 5 1 6 0.8 15 1 19 0.8 21 0.8
1 1 3 1 4 1 5 1 6 0.8 16 1 19 0.8 21 0.8
1 1 3 1 4 1 5 1 6 0.8 17 1 19 0.8 21 0.8
1 1 3 1 4 1 5 1 6 0.8 18 1 19 0.8 21 0.8
1 1 3 1 4 1 5 1 6 0.8 23 1 19 0.8 21 0.8
1 1 3 1 4 1 5 1 6 0.8 24 1 19 0.8 21 0.8
1 1 3 1 4 1 5 1 6 0.8 25 1 19 0.8 21 0.8
1 1 3 1 4 1 5 1 6 0.8 12 1 20 0.8 22 0.8
1 1 3 1 4 1 5 1 6 0.8 13 1 20 0.8 22 0.8
1 1 3 1 4 1 5 1 6 0.8 14 1 20 0.8 22 0.8
1 1 3 1 4 1 5 1 6 0.8 15 1 20 0.8 22 0.8
1 1 3 1 4 1 5 1 6 0.8 16 1 20 0.8 22 0.8
1 1 3 1 4 1 5 1 6 0.8 17 1 20 0.8 22 0.8
1 1 3 1 4 1 5 1 6 0.8 18 1 20 0.8 22 0.8
1 1 3 1 4 1 5 1 6 0.8 23 1 20 0.8 22 0.8
1 1 3 1 4 1 5 1 6 0.8 24 1 20 0.8 22 0.8
1 1 3 1 4 1 5 1 6 0.8 25 1 20 0.8 22 0.8
LOAD COMBINATION 162 THERMAL AS LEADING LOAD
1 1 3 1 4 1 5 1 6 0.8 12 0.75 19 1 21 1
1 1 3 1 4 1 5 1 6 0.8 13 0.75 19 1 21 1
1 1 3 1 4 1 5 1 6 0.8 14 0.75 19 1 21 1
1 1 3 1 4 1 5 1 6 0.8 15 0.75 19 1 21 1
1 1 3 1 4 1 5 1 6 0.8 16 0.75 19 1 21 1
1 1 3 1 4 1 5 1 6 0.8 17 0.75 19 1 21 1
1 1 3 1 4 1 5 1 6 0.8 18 0.75 19 1 21 1
1 1 3 1 4 1 5 1 6 0.8 23 0.75 19 1 21 1
1 1 3 1 4 1 5 1 6 0.8 24 0.75 19 1 21 1
1 1 3 1 4 1 5 1 6 0.8 25 0.75 19 1 21 1
1 1 3 1 4 1 5 1 6 0.8 12 0.75 20 1 22 1
1 1 3 1 4 1 5 1 6 0.8 13 0.75 20 1 22 1
1 1 3 1 4 1 5 1 6 0.8 14 0.75 20 1 22 1
1 1 3 1 4 1 5 1 6 0.8 15 0.75 20 1 22 1
1 1 3 1 4 1 5 1 6 0.8 16 0.75 20 1 22 1
1 1 3 1 4 1 5 1 6 0.8 17 0.75 20 1 22 1
1 1 3 1 4 1 5 1 6 0.8 18 0.75 20 1 22 1
1 1 3 1 4 1 5 1 6 0.8 23 0.75 20 1 22 1
1 1 3 1 4 1 5 1 6 0.8 24 0.75 20 1 22 1
1 1 3 1 4 1 5 1 6 0.8 25 0.75 20 1 22 1
1 1 3 1 4 1 9 1 19 1 21 1
1 1 3 1 4 1 9 1 20 1 22 1
* HFL Partial Safety for Verification of Serviceability Limit State (Rare Combination)
2 1 3 1 4 1 7 1 8 0.8 12 1 19 0.8 21 0.8 11 1
2 1 3 1 4 1 7 1 8 0.8 13 1 19 0.8 21 0.8 11 1
2 1 3 1 4 1 7 1 8 0.8 14 1 19 0.8 21 0.8 11 1
2 1 3 1 4 1 7 1 8 0.8 15 1 19 0.8 21 0.8 11 1
2 1 3 1 4 1 7 1 8 0.8 16 1 19 0.8 21 0.8 11 1
2 1 3 1 4 1 7 1 8 0.8 17 1 19 0.8 21 0.8 11 1
2 1 3 1 4 1 7 1 8 0.8 18 1 19 0.8 21 0.8 11 1
2 1 3 1 4 1 7 1 8 0.8 23 1 19 0.8 21 0.8 11 1
2 1 3 1 4 1 7 1 8 0.8 24 1 19 0.8 21 0.8 11 1
2 1 3 1 4 1 7 1 8 0.8 25 1 19 0.8 21 0.8 11 1
2 1 3 1 4 1 7 1 8 0.8 12 1 20 0.8 22 0.8 11 1
2 1 3 1 4 1 7 1 8 0.8 13 1 20 0.8 22 0.8 11 1
2 1 3 1 4 1 7 1 8 0.8 14 1 20 0.8 22 0.8 11 1
2 1 3 1 4 1 7 1 8 0.8 15 1 20 0.8 22 0.8 11 1
2 1 3 1 4 1 7 1 8 0.8 16 1 20 0.8 22 0.8 11 1
2 1 3 1 4 1 7 1 8 0.8 17 1 20 0.8 22 0.8 11 1
2 1 3 1 4 1 7 1 8 0.8 18 1 20 0.8 22 0.8 11 1
2 1 3 1 4 1 7 1 8 0.8 23 1 20 0.8 22 0.8 11 1
2 1 3 1 4 1 7 1 8 0.8 24 1 20 0.8 22 0.8 11 1
2 1 3 1 4 1 7 1 8 0.8 25 1 20 0.8 22 0.8 11 1
2 1 3 1 4 1 7 1 8 0.8 12 0.75 19 1 21 1 11 1
2 1 3 1 4 1 7 1 8 0.8 13 0.75 19 1 21 1 11 1
2 1 3 1 4 1 7 1 8 0.8 14 0.75 19 1 21 1 11 1
2 1 3 1 4 1 7 1 8 0.8 15 0.75 19 1 21 1 11 1
2 1 3 1 4 1 7 1 8 0.8 16 0.75 19 1 21 1 11 1
2 1 3 1 4 1 7 1 8 0.8 17 0.75 19 1 21 1 11 1
2 1 3 1 4 1 7 1 8 0.8 18 0.75 19 1 21 1 11 1
2 1 3 1 4 1 7 1 8 0.8 23 0.75 19 1 21 1 11 1
2 1 3 1 4 1 7 1 8 0.8 24 0.75 19 1 21 1 11 1
2 1 3 1 4 1 7 1 8 0.8 25 0.75 19 1 21 1 11 1
2 1 3 1 4 1 7 1 8 0.8 12 0.75 20 1 22 1 11 1
2 1 3 1 4 1 7 1 8 0.8 13 0.75 20 1 22 1 11 1
2 1 3 1 4 1 7 1 8 0.8 14 0.75 20 1 22 1 11 1
2 1 3 1 4 1 7 1 8 0.8 15 0.75 20 1 22 1 11 1
2 1 3 1 4 1 7 1 8 0.8 16 0.75 20 1 22 1 11 1
2 1 3 1 4 1 7 1 8 0.8 17 0.75 20 1 22 1 11 1
2 1 3 1 4 1 7 1 8 0.8 18 0.75 20 1 22 1 11 1
2 1 3 1 4 1 7 1 8 0.8 23 0.75 20 1 22 1 11 1
2 1 3 1 4 1 7 1 8 0.8 24 0.75 20 1 22 1 11 1
2 1 3 1 4 1 7 1 8 0.8 25 0.75 20 1 22 1 11 1
2 1 3 1 4 1 10 1 19 1 21 1 11 1
2 1 3 1 4 1 10 1 20 1 22 1 11 1
*Partial Safety for Verification of Serviceability Limit State (Frequent Combination)
1 1 3 1 4 1 5 1 12 0.75 19 0.5 21 0.5
1 1 3 1 4 1 5 1 13 0.75 19 0.5 21 0.5
1 1 3 1 4 1 5 1 14 0.75 19 0.5 21 0.5
1 1 3 1 4 1 5 1 15 0.75 19 0.5 21 0.5
1 1 3 1 4 1 5 1 16 0.75 19 0.5 21 0.5
1 1 3 1 4 1 5 1 17 0.75 19 0.5 21 0.5
1 1 3 1 4 1 5 1 18 0.75 19 0.5 21 0.5
1 1 3 1 4 1 5 1 23 0.75 19 0.5 21 0.5
1 1 3 1 4 1 5 1 24 0.75 19 0.5 21 0.5
1 1 3 1 4 1 5 1 25 0.75 19 0.5 21 0.5
1 1 3 1 4 1 5 1 12 0.75 20 0.5 22 0.5
1 1 3 1 4 1 5 1 13 0.75 20 0.5 22 0.5
1 1 3 1 4 1 5 1 14 0.75 20 0.5 22 0.5
1 1 3 1 4 1 5 1 15 0.75 20 0.5 22 0.5
1 1 3 1 4 1 5 1 16 0.75 20 0.5 22 0.5
1 1 3 1 4 1 5 1 17 0.75 20 0.5 22 0.5
1 1 3 1 4 1 5 1 18 0.75 20 0.5 22 0.5
1 1 3 1 4 1 5 1 23 0.75 20 0.5 22 0.5
1 1 3 1 4 1 5 1 24 0.75 20 0.5 22 0.5
1 1 3 1 4 1 5 1 25 0.75 20 0.5 22 0.5
1 1 3 1 4 1 5 1 12 0.2 19 0.6 21 0.6
1 1 3 1 4 1 5 1 13 0.2 19 0.6 21 0.6
1 1 3 1 4 1 5 1 14 0.2 19 0.6 21 0.6
1 1 3 1 4 1 5 1 15 0.2 19 0.6 21 0.6
1 1 3 1 4 1 5 1 16 0.2 19 0.6 21 0.6
1 1 3 1 4 1 5 1 17 0.2 19 0.6 21 0.6
1 1 3 1 4 1 5 1 18 0.2 19 0.6 21 0.6
1 1 3 1 4 1 5 1 23 0.2 19 0.6 21 0.6
1 1 3 1 4 1 5 1 24 0.2 19 0.6 21 0.6
1 1 3 1 4 1 5 1 25 0.2 19 0.6 21 0.6
1 1 3 1 4 1 5 1 12 0.2 20 0.6 22 0.6
1 1 3 1 4 1 5 1 13 0.2 20 0.6 22 0.6
1 1 3 1 4 1 5 1 14 0.2 20 0.6 22 0.6
1 1 3 1 4 1 5 1 15 0.2 20 0.6 22 0.6
1 1 3 1 4 1 5 1 16 0.2 20 0.6 22 0.6
1 1 3 1 4 1 5 1 17 0.2 20 0.6 22 0.6
1 1 3 1 4 1 5 1 18 0.2 20 0.6 22 0.6
1 1 3 1 4 1 5 1 23 0.2 20 0.6 22 0.6
1 1 3 1 4 1 5 1 24 0.2 20 0.6 22 0.6
1 1 3 1 4 1 5 1 25 0.2 20 0.6 22 0.6
1 1 3 1 4 1 9 1 19 0.6 21 0.6
1 1 3 1 4 1 9 1 20 0.6 22 0.6
* HFL Partial Safety for Verification of Serviceability Limit State (Frequent Combination)
2 1 3 1 4 1 7 1 12 0.75 19 0.5 21 0.5 11 1
2 1 3 1 4 1 7 1 13 0.75 19 0.5 21 0.5 11 1
2 1 3 1 4 1 7 1 14 0.75 19 0.5 21 0.5 11 1
2 1 3 1 4 1 7 1 15 0.75 19 0.5 21 0.5 11 1
2 1 3 1 4 1 7 1 16 0.75 19 0.5 21 0.5 11 1
2 1 3 1 4 1 7 1 17 0.75 19 0.5 21 0.5 11 1
2 1 3 1 4 1 7 1 18 0.75 19 0.5 21 0.5 11 1
2 1 3 1 4 1 7 1 23 0.75 19 0.5 21 0.5 11 1
2 1 3 1 4 1 7 1 24 0.75 19 0.5 21 0.5 11 1
2 1 3 1 4 1 7 1 25 0.75 19 0.5 21 0.5 11 1
2 1 3 1 4 1 7 1 12 0.75 20 0.5 22 0.5 11 1
2 1 3 1 4 1 7 1 13 0.75 20 0.5 22 0.5 11 1
2 1 3 1 4 1 7 1 14 0.75 20 0.5 22 0.5 11 1
2 1 3 1 4 1 7 1 15 0.75 20 0.5 22 0.5 11 1
2 1 3 1 4 1 7 1 16 0.75 20 0.5 22 0.5 11 1
2 1 3 1 4 1 7 1 17 0.75 20 0.5 22 0.5 11 1
2 1 3 1 4 1 7 1 18 0.75 20 0.5 22 0.5 11 1
2 1 3 1 4 1 7 1 23 0.75 20 0.5 22 0.5 11 1
2 1 3 1 4 1 7 1 24 0.75 20 0.5 22 0.5 11 1
2 1 3 1 4 1 7 1 25 0.75 20 0.5 22 0.5 11 1
2 1 3 1 4 1 7 1 12 0.2 19 0.6 21 0.6 11 1
2 1 3 1 4 1 7 1 13 0.2 19 0.6 21 0.6 11 1
2 1 3 1 4 1 7 1 14 0.2 19 0.6 21 0.6 11 1
2 1 3 1 4 1 7 1 15 0.2 19 0.6 21 0.6 11 1
2 1 3 1 4 1 7 1 16 0.2 19 0.6 21 0.6 11 1
2 1 3 1 4 1 7 1 17 0.2 19 0.6 21 0.6 11 1
2 1 3 1 4 1 7 1 18 0.2 19 0.6 21 0.6 11 1
2 1 3 1 4 1 7 1 23 0.2 19 0.6 21 0.6 11 1
2 1 3 1 4 1 7 1 24 0.2 19 0.6 21 0.6 11 1
2 1 3 1 4 1 7 1 25 0.2 19 0.6 21 0.6 11 1
2 1 3 1 4 1 7 1 12 0.2 20 0.6 22 0.6 11 1
2 1 3 1 4 1 7 1 13 0.2 20 0.6 22 0.6 11 1
2 1 3 1 4 1 7 1 14 0.2 20 0.6 22 0.6 11 1
2 1 3 1 4 1 7 1 15 0.2 20 0.6 22 0.6 11 1
2 1 3 1 4 1 7 1 16 0.2 20 0.6 22 0.6 11 1
2 1 3 1 4 1 7 1 17 0.2 20 0.6 22 0.6 11 1
2 1 3 1 4 1 7 1 18 0.2 20 0.6 22 0.6 11 1
2 1 3 1 4 1 7 1 23 0.2 20 0.6 22 0.6 11 1
2 1 3 1 4 1 7 1 24 0.2 20 0.6 22 0.6 11 1
2 1 3 1 4 1 7 1 25 0.2 20 0.6 22 0.6 11 1
2 1 3 1 4 1 10 1 19 0.6 21 0.6 11 1
2 1 3 1 4 1 10 1 20 0.6 22 0.6 11 1
*Partial Safety for Verification of Serviceability Limit State (Quasi-permanent Combination)
1 1 3 1 4 1 5 1 19 0.5 21 0.5
1 1 3 1 4 1 5 1 20 0.5 22 0.5
*HFL Partial Safety for Verification of Serviceability Limit State (Quasi-permanent Combination)
2 1 3 1 4 1 7 1 19 0.5 21 0.5 11 1
2 1 3 1 4 1 7 1 20 0.5 22 0.5 11 1
*Combination for Base Pressure and Design of Foundation (Combination 1 )
LOAD COMBINATION 314 EARTH PRESSURE AS A LEADING LOAD
1 1.35 3 1.35 4 1.75 5 1.5 6 1.2 12 1.15 19 0.9 21 0.9
1 1.35 3 1.35 4 1.75 5 1.5 6 1.2 13 1.15 19 0.9 21 0.9
1 1.35 3 1.35 4 1.75 5 1.5 6 1.2 14 1.15 19 0.9 21 0.9
1 1.35 3 1.35 4 1.75 5 1.5 6 1.2 15 1.15 19 0.9 21 0.9
1 1.35 3 1.35 4 1.75 5 1.5 6 1.2 16 1.15 19 0.9 21 0.9
1 1.35 3 1.35 4 1.75 5 1.5 6 1.2 17 1.15 19 0.9 21 0.9
1 1.35 3 1.35 4 1.75 5 1.5 6 1.2 18 1.15 19 0.9 21 0.9
1 1.35 3 1.35 4 1.75 5 1.5 6 1.2 23 1 19 0.9 21 0.9
1 1.35 3 1.35 4 1.75 5 1.5 6 1.2 24 1 19 0.9 21 0.9
1 1.35 3 1.35 4 1.75 5 1.5 6 1.2 25 1 19 0.9 21 0.9
1 1.35 3 1.35 4 1.75 5 1.5 6 1.2 12 1.15 20 0.9 22 0.9 11 1
1 1.35 3 1.35 4 1.75 5 1.5 6 1.2 13 1.15 20 0.9 22 0.9 11 1
1 1.35 3 1.35 4 1.75 5 1.5 6 1.2 14 1.15 20 0.9 22 0.9 11 1
1 1.35 3 1.35 4 1.75 5 1.5 6 1.2 15 1.15 20 0.9 22 0.9 11 1
1 1.35 3 1.35 4 1.75 5 1.5 6 1.2 16 1.15 20 0.9 22 0.9 11 1
1 1.35 3 1.35 4 1.75 5 1.5 6 1.2 17 1.15 20 0.9 22 0.9 11 1
1 1.35 3 1.35 4 1.75 5 1.5 6 1.2 18 1.15 20 0.9 22 0.9 11 1
1 1.35 3 1.35 4 1.75 5 1.5 6 1.2 23 1 20 0.9 22 0.9 11 1
1 1.35 3 1.35 4 1.75 5 1.5 6 1.2 24 1 20 0.9 22 0.9 11 1
1 1.35 3 1.35 4 1.75 5 1.5 6 1.2 25 1 20 0.9 22 0.9 11 1
LOAD COMBINATION 334 LL AS A LEADING LOAD
1 1.35 3 1.35 4 1.75 5 1 6 1.2 12 1.5 19 0.9 21 0.9
1 1.35 3 1.35 4 1.75 5 1 6 1.2 13 1.5 19 0.9 21 0.9
1 1.35 3 1.35 4 1.75 5 1 6 1.2 14 1.5 19 0.9 21 0.9
1 1.35 3 1.35 4 1.75 5 1 6 1.2 15 1.5 19 0.9 21 0.9
1 1.35 3 1.35 4 1.75 5 1 6 1.2 16 1.5 19 0.9 21 0.9
1 1.35 3 1.35 4 1.75 5 1 6 1.2 17 1.5 19 0.9 21 0.9
1 1.35 3 1.35 4 1.75 5 1 6 1.2 18 1.5 19 0.9 21 0.9
1 1.35 3 1.35 4 1.75 5 1 6 1.2 23 1 19 0.9 21 0.9
1 1.35 3 1.35 4 1.75 5 1 6 1.2 24 1 19 0.9 21 0.9
1 1.35 3 1.35 4 1.75 5 1 6 1.2 25 1 19 0.9 21 0.9
1 1.35 3 1.35 4 1.75 5 1 6 1.2 12 1.5 20 0.9 22 0.9 11 1
1 1.35 3 1.35 4 1.75 5 1 6 1.2 13 1.5 20 0.9 22 0.9 11 1
1 1.35 3 1.35 4 1.75 5 1 6 1.2 14 1.5 20 0.9 22 0.9 11 1
1 1.35 3 1.35 4 1.75 5 1 6 1.2 15 1.5 20 0.9 22 0.9 11 1
1 1.35 3 1.35 4 1.75 5 1 6 1.2 16 1.5 20 0.9 22 0.9 11 1
1 1.35 3 1.35 4 1.75 5 1 6 1.2 17 1.5 20 0.9 22 0.9 11 1
1 1.35 3 1.35 4 1.75 5 1 6 1.2 18 1.5 20 0.9 22 0.9 11 1
1 1.35 3 1.35 4 1.75 5 1 6 1.2 23 1 20 0.9 22 0.9 11 1
1 1.35 3 1.35 4 1.75 5 1 6 1.2 24 1 20 0.9 22 0.9 11 1
1 1.35 3 1.35 4 1.75 5 1 6 1.2 25 1 20 0.9 22 0.9 11 1
*HFL Combination for Base Pressure and Design of Foundation (Combination 1 )
2 1.35 3 1.35 4 1.75 7 1.5 6 1.2 12 1.15 19 0.9 21 0.9 11 1
2 1.35 3 1.35 4 1.75 7 1.5 6 1.2 13 1.15 19 0.9 21 0.9 11 1
2 1.35 3 1.35 4 1.75 7 1.5 6 1.2 14 1.15 19 0.9 21 0.9 11 1
2 1.35 3 1.35 4 1.75 7 1.5 6 1.2 15 1.15 19 0.9 21 0.9 11 1
2 1.35 3 1.35 4 1.75 7 1.5 6 1.2 16 1.15 19 0.9 21 0.9 11 1
2 1.35 3 1.35 4 1.75 7 1.5 6 1.2 17 1.15 19 0.9 21 0.9 11 1
2 1.35 3 1.35 4 1.75 7 1.5 6 1.2 18 1.15 19 0.9 21 0.9 11 1
2 1.35 3 1.35 4 1.75 7 1.5 6 1.2 23 1 20 0.9 22 0.9 11 1
2 1.35 3 1.35 4 1.75 7 1.5 6 1.2 24 1 20 0.9 22 0.9 11 1
2 1.35 3 1.35 4 1.75 7 1.5 6 1.2 25 1 20 0.9 22 0.9 11 1
2 1.35 3 1.35 4 1.75 7 1.5 6 1.2 12 1.15 20 0.9 22 0.9 11 1
2 1.35 3 1.35 4 1.75 7 1.5 6 1.2 13 1.15 20 0.9 22 0.9 11 1
2 1.35 3 1.35 4 1.75 7 1.5 6 1.2 14 1.15 20 0.9 22 0.9 11 1
2 1.35 3 1.35 4 1.75 7 1.5 6 1.2 15 1.15 20 0.9 22 0.9 11 1
2 1.35 3 1.35 4 1.75 7 1.5 6 1.2 16 1.15 20 0.9 22 0.9 11 1
2 1.35 3 1.35 4 1.75 7 1.5 6 1.2 17 1.15 20 0.9 22 0.9 11 1
2 1.35 3 1.35 4 1.75 7 1.5 6 1.2 18 1.15 20 0.9 22 0.9 11 1
2 1.35 3 1.35 4 1.75 7 1.5 6 1.2 23 1 21 0.9 23 0.9 11 1
2 1.35 3 1.35 4 1.75 7 1.5 6 1.2 24 1 21 0.9 23 0.9 11 1
2 1.35 3 1.35 4 1.75 7 1.5 6 1.2 25 1 21 0.9 23 0.9 11 1
2 1.35 3 1.35 4 1.75 7 1 6 1.2 12 1.5 19 0.9 21 0.9 11 1
2 1.35 3 1.35 4 1.75 7 1 6 1.2 13 1.5 19 0.9 21 0.9 11 1
2 1.35 3 1.35 4 1.75 7 1 6 1.2 14 1.5 19 0.9 21 0.9 11 1
2 1.35 3 1.35 4 1.75 7 1 6 1.2 15 1.5 19 0.9 21 0.9 11 1
2 1.35 3 1.35 4 1.75 7 1 6 1.2 16 1.5 19 0.9 21 0.9 11 1
2 1.35 3 1.35 4 1.75 7 1 6 1.2 17 1.5 19 0.9 21 0.9 11 1
2 1.35 3 1.35 4 1.75 7 1 6 1.2 18 1.5 19 0.9 21 0.9 11 1
2 1.35 3 1.35 4 1.75 7 1 6 1.2 23 1 20 0.9 22 0.9 11 1
2 1.35 3 1.35 4 1.75 7 1 6 1.2 24 1 20 0.9 22 0.9 11 1
2 1.35 3 1.35 4 1.75 7 1 6 1.2 25 1 20 0.9 22 0.9 11 1
2 1.35 3 1.35 4 1.75 7 1 6 1.2 12 1.5 20 0.9 22 0.9 11 1
2 1.35 3 1.35 4 1.75 7 1 6 1.2 13 1.5 20 0.9 22 0.9 11 1
2 1.35 3 1.35 4 1.75 7 1 6 1.2 14 1.5 20 0.9 22 0.9 11 1
2 1.35 3 1.35 4 1.75 7 1 6 1.2 15 1.5 20 0.9 22 0.9 11 1
2 1.35 3 1.35 4 1.75 7 1 6 1.2 16 1.5 20 0.9 22 0.9 11 1
2 1.35 3 1.35 4 1.75 7 1 6 1.2 17 1.5 20 0.9 22 0.9 11 1
2 1.35 3 1.35 4 1.75 7 1 6 1.2 18 1.5 20 0.9 22 0.9 11 1
2 1.35 3 1.35 4 1.75 7 1 6 1.2 23 1 20 0.9 22 0.9 11 1
2 1.35 3 1.35 4 1.75 7 1 6 1.2 24 1 20 0.9 22 0.9 11 1
2 1.35 3 1.35 4 1.75 7 1 6 1.2 25 1 20 0.9 22 0.9 11 1
1 1.35 3 1.35 4 1.75 5 1.5 12 1.15 19 0.9 21 0.9
1 1.35 3 1.35 4 1.75 5 1.5 13 1.15 19 0.9 21 0.9
1 1.35 3 1.35 4 1.75 5 1.5 14 1.15 19 0.9 21 0.9
1 1.35 3 1.35 4 1.75 5 1.5 15 1.15 19 0.9 21 0.9
1 1.35 3 1.35 4 1.75 5 1.5 16 1.15 19 0.9 21 0.9
1 1.35 3 1.35 4 1.75 5 1.5 17 1.15 19 0.9 21 0.9
1 1.35 3 1.35 4 1.75 5 1.5 18 1.15 19 0.9 21 0.9
1 1.35 3 1.35 4 1.75 5 1.5 12 1.15 20 0.9 22 0.9
1 1.35 3 1.35 4 1.75 5 1.5 13 1.15 20 0.9 22 0.9
1 1.35 3 1.35 4 1.75 5 1.5 14 1.15 20 0.9 22 0.9
1 1.35 3 1.35 4 1.75 5 1.5 15 1.15 20 0.9 22 0.9
1 1.35 3 1.35 4 1.75 5 1.5 16 1.15 20 0.9 22 0.9
1 1.35 3 1.35 4 1.75 5 1.5 17 1.15 20 0.9 22 0.9
1 1.35 3 1.35 4 1.75 5 1.5 18 1.15 20 0.9 22 0.9
1 1.35 3 1.35 4 1.75 5 1.5 23 1 20 0.9 22 0.9
1 1.35 3 1.35 4 1.75 5 1.5 24 1 20 0.9 22 0.9
1 1.35 3 1.35 4 1.75 5 1.5 25 1 20 0.9 22 0.9
1 1.35 3 1.35 4 1.75 5 1 12 1.5 19 0.9 21 0.9
1 1.35 3 1.35 4 1.75 5 1 13 1.5 19 0.9 21 0.9
1 1.35 3 1.35 4 1.75 5 1 14 1.5 19 0.9 21 0.9
1 1.35 3 1.35 4 1.75 5 1 15 1.5 19 0.9 21 0.9
1 1.35 3 1.35 4 1.75 5 1 16 1.5 19 0.9 21 0.9
1 1.35 3 1.35 4 1.75 5 1 17 1.5 19 0.9 21 0.9
1 1.35 3 1.35 4 1.75 5 1 18 1.5 19 0.9 21 0.9
1 1.35 3 1.35 4 1.75 5 1 23 1 19 0.9 21 0.9
1 1.35 3 1.35 4 1.75 5 1 24 1 19 0.9 21 0.9
1 1.35 3 1.35 4 1.75 5 1 25 1 19 0.9 21 0.9
1 1.35 3 1.35 4 1.75 5 1 12 1.5 20 0.9 22 0.9
1 1.35 3 1.35 4 1.75 5 1 13 1.5 20 0.9 22 0.9
1 1.35 3 1.35 4 1.75 5 1 14 1.5 20 0.9 22 0.9
1 1.35 3 1.35 4 1.75 5 1 15 1.5 20 0.9 22 0.9
1 1.35 3 1.35 4 1.75 5 1 16 1.5 20 0.9 22 0.9
1 1.35 3 1.35 4 1.75 5 1 17 1.5 20 0.9 22 0.9
1 1.35 3 1.35 4 1.75 5 1 18 1.5 20 0.9 22 0.9
1 1.35 3 1.35 4 1.75 5 1 23 1 20 0.9 22 0.9
1 1.35 3 1.35 4 1.75 5 1 24 1 20 0.9 22 0.9
1 1.35 3 1.35 4 1.75 5 1 25 1 20 0.9 22 0.9
*Combination for Base Pressure and Design of Foundation (Combination 2 )
1 1 3 1 4 1 5 1.3 6 1 12 1 19 0.8 21 0.8
1 1 3 1 4 1 5 1.3 6 1 13 1 19 0.8 21 0.8
1 1 3 1 4 1 5 1.3 6 1 14 1 19 0.8 21 0.8
1 1 3 1 4 1 5 1.3 6 1 15 1 19 0.8 21 0.8
1 1 3 1 4 1 5 1.3 6 1 16 1 19 0.8 21 0.8
1 1 3 1 4 1 5 1.3 6 1 17 1 19 0.8 21 0.8
1 1 3 1 4 1 5 1.3 6 1 18 1 19 0.8 21 0.8
1 1 3 1 4 1 5 1.3 6 1 23 1 19 0.8 21 0.8
1 1 3 1 4 1 5 1.3 6 1 24 1 19 0.8 21 0.8
1 1 3 1 4 1 5 1.3 6 1 25 1 19 0.8 21 0.8
1 1 3 1 4 1 5 1.3 6 1 12 1 20 0.8 22 0.8 11 1
1 1 3 1 4 1 5 1.3 6 1 13 1 20 0.8 22 0.8 11 1
1 1 3 1 4 1 5 1.3 6 1 14 1 20 0.8 22 0.8 11 1
1 1 3 1 4 1 5 1.3 6 1 15 1 20 0.8 22 0.8 11 1
1 1 3 1 4 1 5 1.3 6 1 16 1 20 0.8 22 0.8 11 1
1 1 3 1 4 1 5 1.3 6 1 17 1 20 0.8 22 0.8 11 1
1 1 3 1 4 1 5 1.3 6 1 18 1 20 0.8 22 0.8 11 1
1 1 3 1 4 1 5 1.3 6 1 23 1 20 0.8 22 0.8 11 1
1 1 3 1 4 1 5 1.3 6 1 24 1 20 0.8 22 0.8 11 1
1 1 3 1 4 1 5 1.3 6 1 25 1 20 0.8 22 0.8 11 1
1 1 3 1 4 1 5 0.8 6 1 12 1.3 19 0.8 21 0.8
1 1 3 1 4 1 5 0.8 6 1 13 1.3 19 0.8 21 0.8
1 1 3 1 4 1 5 0.8 6 1 14 1.3 19 0.8 21 0.8
1 1 3 1 4 1 5 0.8 6 1 15 1.3 19 0.8 21 0.8
1 1 3 1 4 1 5 0.8 6 1 16 1.3 19 0.8 21 0.8
1 1 3 1 4 1 5 0.8 6 1 17 1.3 19 0.8 21 0.8
1 1 3 1 4 1 5 0.8 6 1 18 1.3 19 0.8 21 0.8
1 1 3 1 4 1 5 0.8 6 1 23 1 19 0.8 21 0.8
1 1 3 1 4 1 5 0.8 6 1 24 1 19 0.8 21 0.8
1 1 3 1 4 1 5 0.8 6 1 25 1 19 0.8 21 0.8
1 1 3 1 4 1 5 0.8 6 1 12 1.3 20 0.8 22 0.8 11 1
1 1 3 1 4 1 5 0.8 6 1 13 1.3 20 0.8 22 0.8 11 1
1 1 3 1 4 1 5 0.8 6 1 14 1.3 20 0.8 22 0.8 11 1
1 1 3 1 4 1 5 0.8 6 1 15 1.3 20 0.8 22 0.8 11 1
1 1 3 1 4 1 5 0.8 6 1 16 1.3 20 0.8 22 0.8 11 1
1 1 3 1 4 1 5 0.8 6 1 17 1.3 20 0.8 22 0.8 11 1
1 1 3 1 4 1 5 0.8 6 1 18 1.3 20 0.8 22 0.8 11 1
1 1 3 1 4 1 5 0.8 6 1 23 1 20 0.8 22 0.8 11 1
1 1 3 1 4 1 5 0.8 6 1 24 1 20 0.8 22 0.8 11 1
1 1 3 1 4 1 5 0.8 6 1 25 1 20 0.8 22 0.8 11 1
*HFL Combination for Base Pressure and Design of Foundation (Combination 2 )
2 1 3 1 4 1 7 1.3 6 1 12 1 19 0.8 21 0.8 11 1
2 1 3 1 4 1 7 1.3 6 1 13 1 19 0.8 21 0.8 11 1
2 1 3 1 4 1 7 1.3 6 1 14 1 19 0.8 21 0.8 11 1
2 1 3 1 4 1 7 1.3 6 1 15 1 19 0.8 21 0.8 11 1
2 1 3 1 4 1 7 1.3 6 1 16 1 19 0.8 21 0.8 11 1
2 1 3 1 4 1 7 1.3 6 1 17 1 19 0.8 21 0.8 11 1
2 1 3 1 4 1 7 1.3 6 1 18 1 19 0.8 21 0.8 11 1
2 1 3 1 4 1 7 1.3 6 1 23 1 19 0.8 21 0.8 11 1
2 1 3 1 4 1 7 1.3 6 1 24 1 19 0.8 21 0.8 11 1
2 1 3 1 4 1 7 1.3 6 1 25 1 19 0.8 21 0.8 11 1
2 1 3 1 4 1 7 1.3 6 1 12 1 20 0.8 22 0.8 11 1
2 1 3 1 4 1 7 1.3 6 1 13 1 20 0.8 22 0.8 11 1
2 1 3 1 4 1 7 1.3 6 1 14 1 20 0.8 22 0.8 11 1
2 1 3 1 4 1 7 1.3 6 1 15 1 20 0.8 22 0.8 11 1
2 1 3 1 4 1 7 1.3 6 1 16 1 20 0.8 22 0.8 11 1
2 1 3 1 4 1 7 1.3 6 1 17 1 20 0.8 22 0.8 11 1
2 1 3 1 4 1 7 1.3 6 1 18 1 20 0.8 22 0.8 11 1
2 1 3 1 4 1 7 1.3 6 1 23 1 20 0.8 22 0.8 11 1
2 1 3 1 4 1 7 1.3 6 1 24 1 20 0.8 22 0.8 11 1
2 1 3 1 4 1 7 1.3 6 1 25 1 20 0.8 22 0.8 11 1
2 1 3 1 4 1 7 0.8 6 1 12 1.3 19 0.8 21 0.8 11 1
2 1 3 1 4 1 7 0.8 6 1 13 1.3 19 0.8 21 0.8 11 1
2 1 3 1 4 1 7 0.8 6 1 14 1.3 19 0.8 21 0.8 11 1
2 1 3 1 4 1 7 0.8 6 1 15 1.3 19 0.8 21 0.8 11 1
2 1 3 1 4 1 7 0.8 6 1 16 1.3 19 0.8 21 0.8 11 1
2 1 3 1 4 1 7 0.8 6 1 17 1.3 19 0.8 21 0.8 11 1
2 1 3 1 4 1 7 0.8 6 1 18 1.3 19 0.8 21 0.8 11 1
2 1 3 1 4 1 7 0.8 6 1 23 1 19 0.8 21 0.8 11 1
2 1 3 1 4 1 7 0.8 6 1 24 1 19 0.8 21 0.8 11 1
2 1 3 1 4 1 7 0.8 6 1 25 1 19 0.8 21 0.8 11 1
2 1 3 1 4 1 7 0.8 6 1 12 1.3 20 0.8 22 0.8 11 1
2 1 3 1 4 1 7 0.8 6 1 13 1.3 20 0.8 22 0.8 11 1
2 1 3 1 4 1 7 0.8 6 1 14 1.3 20 0.8 22 0.8 11 1
2 1 3 1 4 1 7 0.8 6 1 15 1.3 20 0.8 22 0.8 11 1
2 1 3 1 4 1 7 0.8 6 1 16 1.3 20 0.8 22 0.8 11 1
2 1 3 1 4 1 7 0.8 6 1 17 1.3 20 0.8 22 0.8 11 1
2 1 3 1 4 1 7 0.8 6 1 18 1.3 20 0.8 22 0.8 11 1
2 1 3 1 4 1 7 0.8 6 1 23 1 20 0.8 22 0.8 11 1
2 1 3 1 4 1 7 0.8 6 1 24 1 20 0.8 22 0.8 11 1
2 1 3 1 4 1 7 0.8 6 1 25 1 20 0.8 22 0.8 11 1
** For base pressure check only
LOAD COMBINATION 511 BASE PRESSURE CHECK FOR LWL CONDITION
1 1 3 1 4 1 5 1 6 1 14 1
LOAD COMBINATION 512 BASE PRESSURE CHECK FOR HFL CONDITION
2 1 3 1 4 1 7 1 8 1 14 1 11 1
PERFORM ANALYSIS PRINT STATICS CHECK
FINISH
7.0 - Summary of Design moments
Values from stadd model
Dimension of Cell TOP SLAB BOTTOM SLAB OUTER SLAB
Moment in Mid- Moment at end Moment in Mid- Moment at end Moment in Mid- Moment at top Moment at Bottom
Load Case
span support span support span support support
Bottom Face Top Face Inner face

kN-m kN-m kN-m kN-m kN-m kN-m
Partial safety factor for verification

of structural strength(Basic 200.37 141.41 - - 155.15 191.76 142.62
combination) LC-23 to 52

of structural strength(Accidental 126.83 87.40 - - 102.12 119.15 91.74

of Serviceability limit state(Rare 137.02 99.46 143.00 64.20 106.50 130.55 98.82

of Serviceability limit
127.19 87.05 135.34 57.24 103.56 119.16 91.65
state(Frequent combination) LC-
145 to 204

of Serviceability limit state (Quasi- 95.58 65.92 189.14 46.53 45.62 89.51 72.62
permanent) LC-205 to 208
Partial safety factor for design of

foundation(Combination-1) - - 209.66 90.98 - - -
LC-209 to 264

foundation(Combination-2)
LC-265 to 320
- - 150.86 68.80 - - -
0.5
Summary of Design Shear Force at deff from face of support
Top slab Bottom slab Outer wall Inner wall

Load Case
kN kN kN
Partial safety for verification of

structural strength(Basic 180.15 - 17.93 49.21
combination)

173.23

129.53
8.1 Verification of structural strength for top slab
Grade of Concrete fck 30 N/mm2
fcd 13.40 N/mm2 For Basic Combination

fcd 16.75 N/mm2 For Accidental Combination
fcd 13.40 N/mm2 For Seismic Combination
Ec 31000 Mpa As per Table A4.2 of (IRC 112-
2011)
Grade of Steel fy 500.00 N/mm2
As per clause 6.4.2.8, IRC : 112-2011
fyd 434.78 N/mm2 For Basic Combination
fyd 500.00 N/mm2 For Accidental Combination
fyd 434.78 N/mm2 For Seismic Combination
Compressive force in concrete Cu= fcd *b*(3/7xu + 2/3*4/7xu)
17/21*fcd*b*xu
Tensile force in steel Tu= fyd * Ast
Lever Arm = d - (0.416*xu)
Basic combination Accidental combination

Moment of the section Mid span Support Mid span Support Unit
Factored Moment (M1) 200.37 141.41 126.83 87.40 kNm

Design Moment(M=M1) 200.37 141.41 126.83 87.40 kNm
Width(b) 1000 1000 1000 1000 mm
Overall depth of section(D) 350 350 350 350 mm
Cover 45 45 45 45 mm
Effective depth(d) 300 300 300 300 mm
fck 30 30 30 30 N/mm2
fy 500 500 500 500 N/mm2
fctm 2.5 2.5 2.5 2.5
Ru = 4.6*Mu/(fck*b*d2) 0.341 0.241 0.216 0.149
Area of design steel required (Ast =fck/fy*b*d/2*[1-(1-Ru)0.5]) 1696.0 1158.7 1031.5 697.1 mm2
Minimum steel req.(0.13bd%) or 0.26 fctm/fyk bt d 502.3 502.3 502.3 502.3 mm2
Ast required 1696.0 1158.7 1031.5 697.1 mm2
Dia of Bar 10 10 10 10 mm
Spacing of bar 145 145 145 145
Dia of Bar 16 16 16 16
Spacing of bar 145 145 145 145 mm
Ast provided 1928.3 1928.3 1928.3 1928.3 mm2
Pt(%) provided 0.643 0.643 0.643 0.643
Hence Safe Hence Safe Hence Safe Hence Safe
Distrubtion steel
Ast required 385.66 385.66 385.66 385.66 mm2
Ast Provided 436.33 436.33 436.33 436.33 mm2
OK OK OK OK
Check for Shear

Shear force from face of wall
Ultimate design shear force per m length 148.00 kN
Shear Stress(Tv) 0.493 N/mm2
Pt(%) provided 0.643
Depth of section at critical point
cl. 10.3.2(2) Eq. 10.2 of IRC :112-2011
K = 1+Sqrt(200/d) <= 2.0 1.816
cl. 10.3.2(2) Eq. 10.3 of IRC :112-2011
vmin = 0.031 K3/2 fck1/2 0.416
cl. 10.3.1 of IRC :112-2011
p1 = Asl/(bw d) <= 0.02 0.0064
0.12* K *(80* p1* fck )0.33 0.538
Axial compressive force NEd (KN) 0.00 kN
σcp = NEd / Ac < 0.2 fcd 0.00 N/mm2
cl. 10.3.2(2) Eq. 10.1 of IRC :112-2011
VRd.c= [0.12*K*(80*p1 *fck )0.33 + 0.15*σcp]*b*d 161 kN
Min. value VRd.c= [Vmin+ 0.15*σcp]*b*d 125 kN
VRd.c(Max of above two value) 161 kN
Ok
cl. 10.3.2(5) Eq. 10.6 of IRC :112-2010

cl. 10.3.2(5) Eq. 10.5 of IRC :112-2011
0.5 bw d n fcd 1271 kN
OK
Check if shear reinf. Required
No. of link for shear reinf. 6
Dia. of bar for shear reinf. 8 mm
Spacing of the Stirrups (mm) 175 mm
S l.max = 0.75 d 225
OK
Spacing provided in Long. Direction (mm) 180 mm
S t.max = 0.75 d <= 600mm 225
S t. mm 360 mm
Lever arm z 267.85 mm
fywd 347.83
ASW 279.25 mm2
x 77.29 mm
Design strength of reinforcement to resist shear (fywd) 434.78 N/mm2
Design shear resistance of reinforcement,
VRd.s = Asw*z*fywd*cotθ/s 186 KN
Design shear resistance of section > Ultimate shear force, Hence OK
8.2 Verification for serviceability limit state for top slab

As per clause 12.2.1, IRC : 112-2011
fcd 14.40 N/mm2 For Rare Combination
fcd 14.40 N/mm2 For Frequent Combination
fcd 10.80 N/mm2 For Quasi-perma. Combination
Ec 31000 Mpa As per Table A4.2 of (IRC 112-

2011)
As per clause 12.2.2, IRC : 112-2011
fyd 300.00 N/mm2 For Rare Combination
fyd 300.00 N/mm2 For Frequent Combination
fyd 300.00 N/mm2 For Quasi-perma. Combination
Rare Combination Quasi-permanent

Width(b) 1000 1000 1000 1000 mm
Cover 45 45 45 45 mm
fck 30 30 30 30 N/mm2
fy 500 500 500 500 N/mm2
fctm 2.5 2.5 2.5 2.5
Ru = 4.6*Mu/(fck*b*d2) 0.233 0.169 0.163 0.112
Ast required 1120.2 797.9 765.3 520.4 mm2
Ast provided 1928.3 1928.3 1928.3 1928.3 mm2
Pt(%) provided 0.643 0.643 0.643 0.643
Distrubtion steel
Ast required 385.7 385.7 385.7 385.7 mm2
Ast Provided 436.33 436.33 436.33 436.33 mm2
OK OK OK OK
x (mm) 50.22 50.22 66.95 66.95 mm
xu,sls/d 0.70 0.70 0.70 0.70

x/d 0.17 0.17 0.22 0.22
OK OK OK OK
z (mm) 279.11 279.11 272.15 272.15
MRsls (KNm) 161.46 161.46 157.43 157.43
OK OK OK OK
ssc = M/( As z ) 255 185 182 126 N/mm2
OK OK OK OK
sca = M/( 0.8095 z b xu ) 12.08 8.77 6.48 4.47 N/mm2
OK OK OK OK
Calculation of crack width :- LONG TERM Mid span Support

Creep Coefficient, Φ 1.85 1.85
Ecm'= Ecm/(1+Φ) 10.54 10.54
m1 = Es/Ecm 18.98 18.98
m2 = 280/3σcbc 5.27 5.27
m1 18.98 18.98
cl. 12.3.4 (3) of IRC :112-2011
Cover 45.00 45.00
k1 0.80 0.80
k2 0.50 0.50
For skew slab refer eq. 12.10 of IRC :112-2011
r p.eff = As / Ac,eff 0.02 0.02
Sr,max ={ 3.4 c + ( 0.425 k1 k2 f ) / rp.eff } 362 362
cl. 12.3.4 (3) of IRC :112-2011

kt 0.50 0.50
fct,eff 2.90 2.90
Es 200000 200000
Ecm 31000 31000
ae = Es / Ecm 6.45 6.45
(esm-ecm)=(ssc-kt fct,eff(1+ae rp,eff)/rp,eff )/Es >=0.6ssc/Es 0.0005 0.0004
cl. 12.3.4 (2) of IRC :112-2011
Wk = Sr,max (esm - ecm ) 0.20 0.14
cl. 12.3.4 (1) of IRC :112-2011
OK OK
CREEP CALCULATION
Age of concrete at the time of loading,t0 = 28 day

Age of concrete in days at the moment considered, t = 36500 days
Grade of concrete = M30
Mean compressive strength of concrete at age of 28 days,fcm = MPa
M40
Relative humidity,RH = 80 %
Notional size of member,h = 350 mm
0.7
 43.75 
 
Coefficient, α1 =
 f cm 
1.065
0.2
 43.75 
Coefficient, α2 =
 
1.018  f cm 
0.5
 43.75 
 
Coefficient, α3 =
 f cm 
1.046
Creep coefficient φ(t,to) =

ϕ o β c (t, t o )
= 1.8466
φo = ϕ RH .β ( f cm ).β (to )
= 1.862
1 − RH/100
Factor to allow for the effect of RH on notional creep coeff,φRH= 1+
0.13 h o For fcm <= 45
MPa
 1 − RH / 100 
= 1 + .α1 αFor
2 fcm > 45
 0.13 ho  MPa
= 1.284
Factor to allow for the effect of concrete strength on notional creep

coeff,β(fcm)= 18.78/√fcm
= 2.969
Factor to allow for the effect of concrete age at loading on notional

creep coeff,β(to)= 1/(0.1+to0.2)
= 0.488
0.3
coefficient to describe the development of creep with time after  (t − t 0 ) 
loading,βc(t,to)=  
 β H + t − t0 
= 0.992
Coefficient, βH = 1.5[1+(0.012RH)18]ho+250 <= 1500, for fcm <= 45
= 1026.79175
261.456258
Calculation of crack width :- SHORT TERM Mid span Support
n1 6.90 6.90
n2 6.90 6.90
φ eq =( n1 φ12 + n2φ22 ) / (n1 φ1+n2 φ2) 13.69 13.69
cl. 12.3.4 (3) of IRC :112-2011
Cover 45.00 45.00
k1 0.80 0.80
k2 0.50 0.50
r p.eff = As / Ac,eff 0.02 0.02
Sr,max ={ 3.4 c + ( 0.425 k1 k2 f ) / rp.eff } 304 304
cl. 12.3.4 (3) of IRC :112-2011

kt 0.50 0.50
fct,eff 2.90 2.90
Es 200000 200000
Ecm 31000 31000
ae = Es / Ecm 6.45 6.45
cl. 12.3.4 (2) of IRC :112-2011
Wk = Sr,max (esm - ecm ) 0.17 0.11
cl. 12.3.4 (1) of IRC :112-2011
OK OK
CHECK STRESS AS PER IRC : 112-2011
INPUTS
Grade of Concrete fck = 30 Mpa
Clear Cover c = 45 mm
Depth of Section h = 350 mm
Effective Depth d = 300 mm
Width of section b = 1000 mm
Modulus of elascticity Es = 200000.0 Mpa
Diameter of bar φ1 = 10 mm
n1 = 7
Bar spacing = 145 mm
n2 = 7
Area of Steel As = 1928.29 mm2
Bending Moment M = 137.02 kN-m
allowable crack width Wmax = 0.300 mm
Ecm = 31187 Mpa
(Eq. A2-5)
CALCULATIONS
Crack Width : Wk = Ser,max *(ɛsm -ɛcm ) (Eq 12.5)
Calculation of Sr max : (max. crack spacing)
Depth of Neutral Axis x = 116.03 mm
-m*Ast+SQRT(m*Ast)^2+2*mAst.bd
x=
b
Cracked Moment of Inertia (In steel units)

=
I= (bx^3)/3 +mAst (d-x)^2 1759201015 mm4
The Concrete Stress at Top of section
σc = M*x/I = 9.04 Mpa
The Reinforcement Stress
σs = m* (M* (d-x)/I) = 271.92 Mpa

9.1 Verification of structural strength for Bottom slab
fcd 13.40 N/mm2 Combination-1

fcd 16.75 N/mm2 Combination-2
Ec 31000 Mpa As per Table A4.2 of
(IRC 112-2011)
As per clause 6.4.2.8, IRC : 112-2011
fyd 434.78 N/mm2 Combination-1
fyd 500.00 N/mm2 Combination-2
17/21*fcd*b*xu
Combination-1 Combination-2

Width(b) 1000 1000 1000 1000 mm
Cover 45 75 45 75 mm
fck 30 30 30 30 N/mm2
fy 500 500 500 500 N/mm2
fctm 2.5 2.5 2.5 2.5
Ru = 4.6*Mu/(fck*b*d2) 0.264 0.136 0.190 0.103
Ast required 1487.4 677.9 1046.5 535.8 mm2
Dia of Bar 16 16 16 16
Ast provided 2166.6 1928.3 2166.6 1928.3 mm2
Pt(%) provided 0.621 0.603 0.621 0.603
Distrubtion steel
Ast required 433.32 385.66 433.32 385.66 mm2
Ast Provided 436.33 436.33 436.33 436.33 mm2
OK OK OK OK
Check for Shear

cl. 10.3.2(2) Eq. 10.2 of IRC :112-2010
K = 1+Sqrt(200/d) <= 2.0 1.791
cl. 10.3.2(2) Eq. 10.3 of IRC :112-2010
vmin = 0.031 K3/2 fck1/2 0.407
cl. 10.3.1 of IRC :112-2011
p1 = Asl/(bw d) <= 0.02 0.0060
0.12* K *(80* p1* fck )0.33 0.519
cl. 10.3.2(2) Eq. 10.1 of IRC :112-2010
VRd.c= [0.12*K*(80*p1 *fck )0.33 + 0.15*σcp]*b*d 166 kN
Provide shear reinforcement
cl. 10.3.2(5) Eq. 10.6 of IRC :112-2010
v = 0.6 ( 1 - fck / 310) 0.54
cl. 10.3.2(5) Eq. 10.5 of IRC :112-2011
OK
Check if shear reinf. Required
No. of link for shear reinf. 6
Dia. of bar for shear reinf. 8 mm
Spacing of the Stirrups (mm) 150 mm
S l.max = 0.75 d 240
OK
Spacing provided in Long. Direction (mm) 180 mm
S t.max = 0.75 d <= 600mm 240
S t. mm 360 mm
Lever arm z 287.85 mm
fywd 347.83
ASW 279.25 mm2
x 77.29 mm
Design strength of reinforcement to resist shear (fywd) 434.78 N/mm2
Design shear resistance of reinforcement,
VRd.s = Asw*z*fywd*cotθ/s 233 KN
Design shear resistance of section > Ultimate shear force, Hence OK
9.2 Verification for serviceability limit state for Bottom slab

As per clause 12.2.1, IRC : 112-2011

(IRC 112-2011)
As per clause 12.2.2, IRC : 112-2011

Design Moment(M=M1) 143 64.20 189.14 46.53 kNm
Width(b) 1000 1000 1000 1000 mm
Cover 45 75 45 75 mm
fck 30 30 30 30 N/mm2
fy 500 500 500 500 N/mm2
fctm 2.5 2.5 2.5 2.5
Ru = 4.6*Mu/(fck*b*d2) 0.180 0.096 0.238 0.070
Ast required 989.1 535.8 1331.1 535.8 mm2
Dia of Bar 16 16 16 16
Ast provided 2166.6 1928.3 2166.6 1928.3 mm2
Pt(%) provided 0.621 0.603 0.621 0.603
Distrubtion steel
Ast required 433.3 385.7 433.3 385.7 mm2
Ast Provided 436.33 436.33 436.33 436.33 mm2
OK OK OK OK
x (mm) 56.42 50.22 75.23 66.95 mm
xu,sls/d 0.70 0.70 0.70 0.70

x/d 0.16 0.16 0.22 0.21
OK OK OK OK
z (mm) 325.53 299.11 317.70 292.15
MRsls (KNm) 211.59 173.03 206.50 169.00
OK OK OK OK
ssc = M/( As z ) 203 111 275 83 N/mm2
OK OK OK OK
sca = M/( 0.8095 z b xu ) 9.62 5.28 9.78 2.94 N/mm2
OK OK OK OK
Calculation of crack width Mid span Support

Ecm'= Ecm/(1+Φ) 10.61 10.61
m = Es/Ecm 18.85 18.85
m 18.85 18.85
cl. 12.3.4 (3) of IRC :112-2011
Cover 40.00 50.00
k1 0.80 0.80
k2 0.50 0.50
r p.eff = As / Ac,eff 0.02 0.01
Sr,max ={ 3.4 c + ( 0.425 k1 k2 f ) / rp.eff } 325 502
cl. 12.3.4 (3) of IRC :112-2011

kt 0.50 0.50
fct,eff 2.90 2.90
Es 200000 200000
Ecm 31000 31000
ae = Es / Ecm 6.45 6.45
cl. 12.3.4 (2) of IRC :112-2011
Wk = Sr,max (esm - ecm ) 0.292 0.124
cl. 12.3.4 (1) of IRC :112-2011
OK OK
CREEP CALCULATION

Mean compressive strength of concrete at age of 28 days,fcm = 40 MPa
0.7
 43.75 
Coefficient, α1 =
 
1.065
 f cm 
0.2
 43.75 
Coefficient, α2 =
 
1.018  f cm 
0.5
 43.75 
 
Coefficient, α3 =
 f cm 
1.046
Creep coefficient φ(t,to) = ϕ o β c (t, t o )

= 1.8272
= 1.844
1 − RH/100
Factor to allow for the effect of RH on notional creep coeff,φRH= 1+ For fcm <= 45
0.13 h o MPa
 1 − RH / 100 
= 1 + .α1 α 2 For fcm > 45
 0.13 ho  MPa
= 1.271

coeff,β(fcm )= 18.78/√fcm
= 2.969

= 0.488
0 .3
 β H + t − t0 
= 0.991
1.5[1+(0.012RH)18]ho+250α3 <= 1500α3, for fcm > 45
= 1137.762
261.456258
Calculation of crack width :- SHORT TERM Mid span Support
n1 6.90 6.90
n2 6.90 6.90
φ eq =( n1 φ12 + n2φ22 ) / (n1 φ1+n2 φ2) 14.29 13.69
cl. 12.3.4 (3) of IRC :112-2011
Cover 45.00 50.00
k1 0.80 0.80
k2 0.50 0.50
r p.eff = As / Ac,eff 0.02 0.01
Sr,max ={ 3.4 c + ( 0.425 k1 k2 f ) / rp.eff } 296 411
cl. 12.3.4 (3) of IRC :112-2011

kt 0.50 0.50
fct,eff 2.90 2.90
Es 200000 200000
Ecm 31000 31000
ae = Es / Ecm 6.45 6.45
cl. 12.3.4 (2) of IRC :112-2011
Wk = Sr,max (esm - ecm ) 0.27 0.10
cl. 12.3.4 (1) of IRC :112-2011
OK OK
INPUTS
n1 = 7
n2 = 7
Ecm = 31187 Mpa
(Eq. A2-5)
CALCULATIONS
x=
b

=
I= (bx^3)/3 +mAst (d-x)^2 2689452023 mm4
σc = M*x/I = 9.34 Mpa
σs = m* (M* (d-x)/I) = 286.49 Mpa

10.1 Verification of structural strength for Outer wall

Ministry of Road Transport and Highway (IRC 112-2011)
As per clause 6.4.2.8, IRC : 112-2011
17/21*fcd*b*xu

Bottom Bottom
Moment of the section Top support Support Top support Support Unit

Width(b) 1000 1000 1000 1000 mm
Cover 45 75 45 75 mm
fck 30 30 30 30 N/mm2
fy 500 500 500 500 N/mm2
fctm 2.5 2.5 2.5 2.5
Ru = 4.6*Mu/(fck*b*d2) 0.240 0.214 0.149 0.137
Ast required 1346.5 1086.5 814.6 683.7 mm2
Dia of Bar 16 16 16 16
Ast provided 1928.3 1928.3 1928.3 1928.3 mm2
Pt(%) provided 0.551 0.603 0.551 0.603
Distrubtion steel
Ast required 385.66 385.66 385.66 385.66 mm2
Ast Provided 436.33 436.33 436.33 436.33 mm2
OK OK OK OK
Check for Shear

cl. 10.3.2(2) Eq. 10.2 of IRC :112-2010
K = 1+Sqrt(200/d) <= 2.0 1.791
cl. 10.3.2(2) Eq. 10.3 of IRC :112-2010
vmin = 0.031 K3/2 fck1/2 0.407
cl. 10.3.1 of IRC :112-2011
p1 = Asl/(bw d) <= 0.02 0.0060
0.12* K *(80* p1* fck )0.33 0.519
cl. 10.3.2(2) Eq. 10.1 of IRC :112-2010
V = [0.12*K*(80*p *f )0.33 + 0.15*σ ]*b*d 166 kN
Ok
cl. 10.3.2(5) Eq. 10.6 of IRC :112-2010

v = 0.6 ( 1 - fck / 310) 0.54
cl. 10.3.2(5) Eq. 10.5 of IRC :112-2011
OK
10.2 Verification for serviceability limit state for Outer wall

As per clause 12.2.1, IRC : 112-2011

(IRC 112-2011)
As per clause 12.2.2, IRC : 112-2011

Bottom Bottom
Moment of the section Top support Support Top support Support Unit
Width(b) 1000 1000 1000 1000 mm
Cover 45 75 45 75 mm
fck 30 30 30 30 N/mm2
fy 500 500 500 500 N/mm2
fctm 2.5 2.5 2.5 2.5
Ru = 4.6*Mu/(fck*b*d2) 0.163 0.148 0.112 0.109
Ast required 896.2 738.6 605.7 536.9 mm2
Spacing of bar 145 145 145 145 0
Dia of Bar 16 16 16 16 0
Ast provided 1928.3 1928.3 1928.3 1928.3 mm2
Pt(%) provided 0.551 0.603 0.551 0.603
Distrubtion steel
Ast required 385.7 385.7 385.7 385.7 mm2
Ast Provided 436.33 436.33 436.33 436.33 mm2
OK OK OK OK
x (mm) 50.22 50.22 66.95 66.95 mm
xu,sls/d 0.70 0.70 0.70 0.70

x/d 0.14 0.16 0.19 0.21
OK OK OK OK
z (mm) 329.11 299.11 322.15 292.15
MRsls (KNm) 190.39 173.03 186.36 169.00
OK OK OK OK
ssc = M/( As z ) 206 171 144 129 N/mm2
OK OK OK OK
sca = M/( 0.8095 z b xu ) 9.76 8.13 5.13 4.59 N/mm2
OK OK OK OK
Bottom
Top support
Calculation of crack width Support
Ecm'= Ecm/(1+Φ) 10.61 10.61
m = Es/Ecm 18.85 18.85
m2 = 280/3σcbc 9.33 9.33
m 18.85 18.85
cl. 12.3.4 (3) of IRC :112-2011
Cover 45.00 50.00
k1 0.80 0.80
k2 0.50 0.50
r p.eff = As / Ac,eff 0.02 0.01
Sr,max ={ 3.4 c + ( 0.425 k1 k2 f ) / rp.eff } 361 502
cl. 12.3.4 (3) of IRC :112-2011

kt 0.50 0.50
fct,eff 2.90 2.90
Es 200000 200000
Ecm 31000 31000
ae = Es / Ecm 6.45 6.45
cl. 12.3.4 (2) of IRC :112-2011
Wk = Sr,max (esm - ecm ) 0.16 0.19
cl. 12.3.4 (1) of IRC :112-2011
OK OK
CREEP CALCULATION

Mean compressive strength of concrete at age of 28 days,fcm = 40 MPa
0.7
 43.75 
 
Coefficient, α1 =
 f cm 
1.065
0.2
 43.75 
 
Coefficient, α2 =
1.018
 f cm 
0.5
 43.75 
 
Coefficient, α3 =
 f cm 
1.046
Creep coefficient φ(t,to) =

ϕ o β c (t, t o )
= 1.8272
= 1.844
1 − RH/100
0.13 h o For fcm <= 45
MPa
 1 − RH / 100 
= 1 + .α1 α 2 For fcm > 45
 0.13 ho  MPa
= 1.271

coeff,β(fcm )= 18.78/√fcm
= 2.969

= 0.488
0 .3
 β H + t − t0 
= 0.991
1.5[1+(0.012RH)18]ho+250α3 <= 1500α3, for fcm > 45
261.456258
Calculation of crack width :- SHORT TERM Top support Bottom Support
n1 6.90 6.90
n2 6.90 6.90
φ eq =( n1 φ12 + n2φ22 ) / (n1 φ1+n2 φ2) 13.69 13.69
cl. 12.3.4 (3) of IRC :112-2011
Cover 45.00 50.00
k1 0.80 0.80
k2 0.50 0.50
r p.eff = As / Ac,eff 0.02 0.01
Sr,max ={ 3.4 c + ( 0.425 k1 k2 f ) / rp.eff } 304 411
cl. 12.3.4 (3) of IRC :112-2011

kt 0.50 0.50
fct,eff 2.90 2.90
Es 200000 200000
Ecm 31000 31000
ae = Es / Ecm 6.45 6.45
cl. 12.3.4 (2) of IRC :112-2011
Wk = Sr,max (esm - ecm ) 0.13 0.16
cl. 12.3.4 (1) of IRC :112-2011
OK OK
INPUTS
n1 = 7
n2 = 7
Ecm = 31187 Mpa
(Eq. A2-5)
CALCULATIONS
x=
b

=
I= (bx^3)/3 +mAst (d-x)^2 2490135845 mm4
σc = M*x/I = 6.67 Mpa
σs = m* (M* (d-x)/I) = 220.11 Mpa

10.3 Verification of structural strength for Outer wall

Ec 31000 Mpa As per Table A4.2 of (IRC
Ministry of Road Transport and Highway 112-2011)
As per clause 6.4.2.8, IRC : 112-2011
17/21*fcd*b*xu

Bottom Bottom
Moment of the section Midspan Midspan Unit
Support Support

Width(b) 1000 1000 1000 1000 mm
Cover 45 75 45 75 mm
fck 30 30 30 30 N/mm2
fy 500 500 500 500 N/mm2
fctm 2.5 2.5 2.5 2.5
Ru = 4.6*Mu/(fck*b*d2) 0.198 0.220 0.130 0.142
Ast required 1084.9 1106.1 700.4 695.4 mm2
Spacing of bar 145 200 145
Dia of Bar 0 20 0 23
Ast provided 1386.6 3141.6 1386.6 #DIV/0! mm2
Pt(%) provided 0.400 0.997 0.400 #DIV/0!
Hence Safe Hence Safe Hence Safe #DIV/0!
Distrubtion steel
Ast required 277.33 628.32 277.33 #DIV/0! mm2
2
Ast Provided 279.25 654.50 279.25 654.50 mm
OK OK OK #DIV/0!
10.4 Verification for serviceability limit state for Outer wall

As per clause 12.2.1, IRC : 112-2011
Ec 31000 Mpa As per Table A4.2 of (IRC

112-2011)
As per clause 12.2.2, IRC : 112-2011

Bottom Bottom
Moment of the section Midspan Support Midspan Support Unit
Width(b) 1000 1000 1000 1000 mm
Cover 45 75 45 75 mm
fck 30 30 30 30 N/mm2
fy 500 500 500 500 N/mm2
fctm 2.5 2.5 2.5 2.5
2
Ru = 4.6*Mu/(fck*b*d ) 0.136 0.153 0.058 0.112
0.5 2
Area of design steel required (Ast =fck/fy*b*d/2*[1-(1-Ru) ]) 731.6 751.4 306.9 546.0 mm
Ast required 731.6 751.4 581.0 546.0 mm2
Spacing of bar 145 200 145 0 0
Dia of Bar 0 20 0 23 0
Ast provided 1386.6 3141.6 1386.6 #DIV/0! mm2
Pt(%) provided 0.400 0.997 0.400 #DIV/0!
Hence Safe Hence Safe Hence Safe #DIV/0!
Distrubtion steel
Ast required 277.3 628.3 277.3 #DIV/0! mm2
Ast Provided 279.25 654.50 279.25 654.50 mm2
OK OK OK #DIV/0!
x (mm) 36.11 130.90 48.15 #DIV/0! mm
xu,sls/d 0.70 0.70 0.70 0.70

x/d 0.10 0.42 0.14 #DIV/0!
OK OK OK #DIV/0!
z (mm) 331.98 260.55 326.97 #DIV/0!
MRsls (KNm) 138.10 245.56 136.02 #DIV/0!
OK OK OK #DIV/0!
ssc = M/( As z ) 231 121 101 #DIV/0! N/mm2
OK OK OK #DIV/0!
sca = M/( 0.8095 z b xu ) 10.97 3.58 3.58 #DIV/0! N/mm2
OK OK OK #DIV/0!
Calculation of crack width Midspan

Creep Coefficient, Φ 1.83
Ecm'= Ecm/(1+Φ) 10.61
m = Es/Ecm 18.85
n2 6.90
m 18.85
cl. 12.3.4 (3) of IRC :112-2011
Cover 45.00
k1 0.80
k2 0.50
r p.eff = As / Ac,eff 0.01
Sr,max ={ 3.4 c + ( 0.425 k1 k2 f ) / rp.eff } 459
cl. 12.3.4 (3) of IRC :112-2011

kt 0.50
fct,eff 2.90
Es 200000
Ecm 31000
ae = Es / Ecm 6.45
(esm-ecm)=(ssc-kt fct,eff(1+ae rp,eff)/rp,eff )/Es >=0.6ssc/Es 0.0003
cl. 12.3.4 (2) of IRC :112-2011
Wk = Sr,max (esm - ecm ) 0.14
cl. 12.3.4 (1) of IRC :112-2011
OK
CREEP CALCULATION

Mean compressive strength of concrete at age of 28 days,fcm = MPa
40
0.7
 43.75 
 
Coefficient, α1 =
 f cm 
1.065
0.2
 43.75 
 
Coefficient, α2 =
1.018
 f cm 
0.5
 43.75 
Coefficient, α3 =
 
1.046  f cm 
Creep coefficient φ(t,to) = ϕ o β c (t, t o )

= 1.8272
φo =
ϕ RH .β ( f cm ).β (t o )
= 1.844
1 − RH/100
0.13 h o For fcm <= 45
MPa
 1 − RH / 100 
= 1 + .α1 α 2 For fcm > 45
 0.13 ho  MPa
= 1.271
Factor to allow for the effect of concrete strength on notional

creep coeff,β(fcm)= 18.78/√fcm
= 2.969
Factor to allow for the effect of concrete age at loading on

notional creep coeff,β(to)= 1/(0.1+to0.2)
= 0.488
0.3
 β H + t − t0 
= 0.991
18
Coefficient, βH = 1.5[1+(0.012RH) ]ho+250 <= 1500, for fcm <= 45
18
1.5[1+(0.012RH) ]ho+250α3 <= 1500α3, for fcm > 45
= 1137.762
261.456258
Calculation of crack width :- SHORT TERM Midspan
n1 6.90
n2 6.90
φ eq =( n1 φ12 + n2φ22 ) / (n1 φ1+n2 φ2) 16.00
cl. 12.3.4 (3) of IRC :112-2011
Cover 45.00
k1 0.80
k2 0.50
r p.eff = As / Ac,eff 0.01
Sr,max ={ 3.4 c + ( 0.425 k1 k2 f ) / rp.eff } 413
cl. 12.3.4 (3) of IRC :112-2011

kt 0.50
fct,eff 2.90
Es 200000
Ecm 31000
ae = Es / Ecm 6.45
(esm-ecm)=(ssc-kt fct,eff(1+ae rp,eff)/rp,eff )/Es >=0.6ssc/Es 0.0003
cl. 12.3.4 (2) of IRC :112-2011
Wk = Sr,max (esm - ecm ) 0.12
cl. 12.3.4 (1) of IRC :112-2011
OK
INPUTS
n1 = 7
n2 = 7
Ecm = 31187 Mpa
(Eq. A2-5)
CALCULATIONS
x=
b

=
I= (bx^3)/3 +mAst (d-x)^2 2099277689 mm4
σc = M*x/I = 3.66 Mpa
σs = m* (M* (d-x)/I) = 262.78 Mpa

12.0 Summary of provided reinforcement 1X5X3 WITH 1.5M CUSHION
i) Top slab
At Midspan (Bottom reinforcement) 1695.96 mm2
Area of steel provided = 1928.29 mm2
10 mm @ 145 mm C/C
16 mm @ 145 mm C/C
ok
At Support (Top reinforcement) 1158.74 mm2
10 mm @ 145 mm C/C
16 mm @ 145 mm C/C
ok
ii) Bottom slab
At Midspan (Top reinforcement) 1487.36 mm2
12 mm @ 145 mm C/C
16 mm @ 145 mm C/C
ok
677.850035 mm2
At Support (Bottom reinforcement) 1928.2879 mm2
10 mm @ 145 mm C/C
16 mm @ 145 mm C/C
ok
iii) Outer wall
At midspan 1084.90 mm2
16 mm @ 145 mm C/C
0 mm @ 145 mm C/C
23
v) Shear Reinforcement
Top slab
8 mm dia 180 mm c/c (Long. Direction) 360 mm c/c (Trans. Direction)
Bottom slab
8 mm dia 180 mm c/c (Long. Direction) 360 mm c/c (Trans. Direction)
ok
Bottom support =
Area of steel required = 589.39 mm2
16 mm @ 145 mm C/C
12 mm @ 145 mm C/C
ok
v) Distrubution steel
Top slab
10 mm @ 180 mm C/C
ok
Bottom slab
10 mm @ 180 mm C/C
ok
Outer wall
8 mm @ 180 mm C/C
ok
13 Base Pressure Check
Check for Base Pressure
Weight of Top Slab 5.08 t/m

Weight of Bottom Slab 5.80 t/m
Weight of Side wall 6.00 t/m
Weight of Intermediate side wall 0.00 t/m
Weight of Railing/Crash Barrier 5.22 t/m
Weight of wearing coat+crust 6.40 t/m
Weight of earth cushion 12.064 t/m
Base Pressure Without Live Load 6.99 t/m2

Base Pressure With Live Load 10.10 t/m2

1X5X3 WITH 1.5m Cast-In-situ

Uploaded by

Copyright:

Available Formats

1X5X3 WITH 1.5m Cast-In-situ

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

1X5X3 WITH 1.5m Cast-In-situ

Uploaded by

Copyright:

Available Formats

Project: CONSTRUCTION OF ACCESS CONTROLLED NAGPUR - MUMBAI SUPER COMMUNICATION EXPRESSWAY

MAHARASHTRA STATE ROAD DEVELOPMENT

R0 21-01-2019 Design of Box Culvert

S.NO. DESCRIPTION Page No

2.0 Dimension of Box 4

3.0 Basic input data 5

4.0 Idealised Structure for Staad Analysis 6

5.0 Load Calculation 7-16

6.0 STAAD input file 17-36

7.0 Summary of Design Moments 37-38

8.0 Design of Top Slab 39-42

9.0 Design of Bottom slab 43-47

10.0 Design of outer wall 48-55

12.0 Summary of reinforcement provided 64-65

13.0 Base pressure check 66

1.2 Design Basis

1.3 Reference documents :-

a) IRC 6 d) Specialised literature as relevant

1.4 Loads has been adopted as per IRC-6

h) Cushion/fill load (if any) is considered as dead load.

1.5 Load cases considered:

No. of Cells 1 No.

Clear Depth 3.00 m

Clear Span 1 Ministry of Road Transport and Highway 5.00 m

Top slab thickNess 0.350 m

Bottom slab thickNess 0.400 m

ThickNess of Outer Wall 0.400 m

Idealised Structure for Staad Analysis

Skew angle 0.00 degree

Ministry of Road Transport and Highway

Density Modulus E Posion

Nos of beam for one span at bottom = 10 Nos.

5.1 Dead load Calucations on top slab (DL)

5.2 Side Wall Loads :

5.2.1 Active Earth Pressure Height

5.80 Kn/m2 1.04 m Top of Slab

23.52 Kn/m2 4.22 m Cg of Wall

24.64 Kn/m2 4.42 m Cg of Base Slab

Earth pressure at rest (Dry conditions) =0.5*(3+0.35/2+0.4/2+1.04)*20

Earth Pressure at base due to live load surcharge = 0.5*20*1.2

Earth Pressure at base due to live load surcharge = 0.279*20*1.2

Earth Pressure at base due to live load surcharge =0.279*(20-10)*1.2+10*1.2*0

5.3 Dead load on base slab due to water =10*2.7

Total Load= 700 Kn 8.27 m 5.00 m

Effective width of Loading

Therefore overlaping due to load dispersion occurs.

Effective width = 7.73 m

Total Load= 700 Kn 5.38 m 5.00 m

Effective width of Loading = 0.279*20*1.2

Therefore overlaping due to load dispersion occurs.

Effective width = 7.71 m

40 T (Boggie load midspan)

Total Load= 400 Kn 5.00 m 5.14 m

Effective width of Loading

Therefore overlaping due to load dispersion occurs.

Effective width = 7.62 m

Total Load= 400 Kn 5.00 m 3.29 m

Effective width of Loading

Therefore overlaping due to load dispersion occurs.

Earth pressure at rest (Dry conditions) =0.5(3+0.35/2+0.4/2+1.04)20

Earth Pressure at base due to live load surcharge = 0.5201.2

Earth Pressure at base due to live load surcharge = 0.279201.2

Earth Pressure at base due to live load surcharge =0.279(20-10)1.2+101.20

Effective width of Loading = 0.279201.2