Inverter

User manual
Frequency Inverter
Serie CV/3CV 200-240V/380 – 480V 0,37 bis 55kW
Tel. (09189) 4147-0, Fax (09189) 4147-47

PETER electronic GmbH & Co. KG, Bruckäcker 9, D-92348 Berg eMail: [email protected]
Internet: www.peter-electronic.com
Quick Start Guide
This guide is to assist in installing and running the inverter to verify that the drive and
motor are working properly. Starting, stopping and speed control will be from the
keypad. If your application requires external control or special system programming,
consult the 7300CV Instruction Manual supplied with your inverter.
Step 1 Before Starting the Inverter

Please review Preface and Safety Precautions (page 0-1 through 1-3) of the 7300CV
Instruction Manual. Verify drive was installed in accordance with the procedures as
described in 7300CV Ambient Environment and Installation on pages 3-1 through 3-8.
If you feel this was abnormal, do not start the drive until qualified personnel have
corrected the situation. (Failure to do so could result in serious injury.)
z Check inverter and motor nameplates to determine that they have the same
HP and voltage ratings. (Ensure that full load motor amps do not exceed
that of the inverter.)
z Remove the terminal cover to expose the motor and power terminals.
a. Verify that AC power is wired to L1, L2, and L3 (pages 3-12).

b. Verify that Motor leads are connected to T1, T2, and T3 (pages 3-12).
(The two leads may need to be reversed if motor rotation is not correct.
1. SEQ LED：1_00 =1, LED Lit.

2. FRQ LED：1_01 = 1/2/3/4, LED Lit
3. FWD LED：Forward Direction, LED action(Flash in stop, Keep Lit in operation).
4. REV LED：Reverse Direction, LED action(Flash in stop, Keep Lit in operation).
5. Four action of FUN、Hz/RPM、VOLT、AMP LED and display of four 7-segment
display, refer to operation description of the keypad.
6. LCD keypad without FUN, Hz/RPM, VOLT, AMP LED.
i
Step 2 Apply Power to the Drive
z Apply AC power to the Drive and observe Operator. Four 7-segment
Display should read Power Voltage for 3~5 seconds and then read
Frequency/Speed, 05.00. Four 7-segment Display and FWD LED should be
flashed all the time.
Step 3 Check Motor Rotation Without Load

z Press RUN key (FWD LED should light); Four 7-segment Display should
run from 00.00 to 05.00.
z Check motor rotation.
If it is not correct:
Press STOP key. Remove AC power. Wait for LED “charge” lamp to extinguish.
Reverse motor leads T1 and T2.Restart the drive and check new rotation.
z Press STOP key to stop the drive.
Step 4 Check Full Speed at 50Hz/60Hz

z Frequency/Speed can be changed by pressing the up or down Arrow keys.
To move right or left for next digit, press SHIFT / RESET key. Press the
READ / ENTER key to set the speed.
z Set frequency up to 50Hz/60Hz in accordance with the last rule.
z Press RUN key. Check drive acceleration to full speed.
z Press STOP key to stop drive and check deceleration.
Step 5 Other Operations

For information, see 7300CV Instruction Manual.
Please refer to the following pages:
Set Accel ......................................................................p. 4-11
Set Decel ..................................................................... p. 4-11
Set Max Speed ............................................................ p. 4-11
Set Min Speed ............................................................. p. 4-11
Set Motor Rated Current .......................................…. p. 4-9
Set Control Mode (Vector, V/F) .............................…. p. 4-7
ii
Table of Content
Quick Start Guide i
Chapter 0 Preface 0-1
0.1 Preface 0-1
0.2 Products Inspection 0-1
Chapter 1 Safety Precautions 1-1
1.1 Operation Precaution 1-1
1.1.1 Before Power ON 1-1
1.1.2 During Power ON 1-2
1.1.3 Before Operation 1-2
1.1.4 During Operation 1-3
1.1.5 During Maintenance 1-3
Chapter 2 Definition of Model 2-1
Chapter 3 Ambient Environment and Installation 3-1
3.1 Environment 3-1
3.2 Environmental Precautions 3-2
3.3 Inflammable Materials 3-3
3.3.1 Notice for Wiring 3-3
3.3.2 Applicable Specification of Magnetic Contactor and Wires 3-5
3.3.3 Precautions for Peripheral Applications 3-6
3.4 Specifications 3-9
3.4.1 Products Individual Specifications 3-9
3.4.2 General Specifications 3-10
3.5 Wiring Diagram 7300CV Series Inverter 3-12
3.6 Description of Terminals Troubleshooting Inverter 3-13
3.7 Outline Dimension 3-15
Chapter 4 Software Index 4-1
4.1 Keypad Description 4-1
4.1.1 Keypad Display and Operation Instruction 4-1
4.1.2 Operation Instruction of the Keypad 4-2
4.1.3 Operation Instruction of the LED Keypad 4-3
4.1.4 Operation Instruction of the LCD Keypad 4-4
4.1.5 Keypad Operating Example 4-5
4.2 Control Mode Selection 4-7
4.3 7300CV Programmable Functions List 4-8
4.4 Parameter Function Description 4-20
4.5 Specification Description on Built-in PLC Function 4-63
4.5.1 Basic Instruction 4-63
4.5.2 Function of Basic Instruction 4-64
4.5.3 Application Instructions 4-65
Chapter 5 Troubleshooting and Maintenance 5-1
5.1 Error Display and Remedy 5-1
5.1.1 Error which can not be Recovered Manually 5-1
5.1.2 Error which can be recovered manually and automatically 5-2
5.1.3 Error which can be recovered manually but not auto matically 5-3
5.1.4 Special Conditions 5-4
5.1.5 Operation Errors 5-5
5.2 General Troubleshooting 5-6
5.3 Quick Troubleshooting 7300CV Series 5-7
5.4 Routine Inspection and Period Inspection 5-13
iii
5.5 Maintenance and Inspection 5-14
Chapter 6 Peripheral Components 6-1
6.1 Reactor Specification at Input Side 6-1
6.2 Reactor Specification at DC Side 6-1
6.3 Braking Resistor 6-2
6.4 Digital Operator and Extension Cable 6-3
6.5 EMC Filter 6-5
6.6 Interface Card 6-7
6.6.1 RS-485 Interface Card 6-7
6.6.2 RS-232 Interface Card 6-8
6.6.3 Program Copy Unit 6-9
6.6.4 PDA Link 6-9
AppendixⅠ 7300CV Motor Internal Parameter List App1
AppendixⅡ 7300CV Parameters Setting List App2
iv
Chapter 0 Preface
Chapter 0 Preface
0.1 Preface
To extend the performance of the product and ensure your safety, please read this manual
thoroughly before using the inverter. Should there be any problem in using the product
and can not be solved with the information provided in the manual, contact your nearest
Teco’s distributor or our sales representatives who will be willing to help you. Please
keep using Teco’s products in the future.
※Precautions
The inverter is an electrical electronic product. For your safety, there are symbols such as
“Danger”, “Caution” in this manual to remind you to pay attention to safety instructions
on handling, installing, operating, and checking the inverter. Be sure to follow the
instructions for highest safety.
Indicates a potential hazard could cause death or serious personal injury

Danger
if misused.
Indicates that the inverter or the mechanical system might be damaged

Caution
if misused.
Danger
z Do not touch any circuit boards or components if the charging indicator is still lit after
turned the power off.
z Do not wire when the inverter is electrified. Do not check parts and signals on circuit boards
during the inverter operation.
z Do not disassemble the inverter and modify internal wires, circuits and parts.
Ground the ground terminal of the inverter properly. As for 200V class ground to 100 Ω or
below, 400v class ground to 10Ω or below.
Caution
z Do not perform a voltage test on parts inside the inverter. High voltage will easily destroy
these semiconductor parts.
z Do not connect T1 (U), T2 (V), and T3 (W) terminals of the inverter to AC power supply.
z CMOS ICs on the inverter’s main board are susceptible to static electricity. Do not touch
the main circuit board
0.2 Products Inspection

Teco’s inverters are all passed the function test before delivery. Please check the
followings when you received and unpacked the inverter:
z The model and capacity of the inverter are the same as those specified in your purchase order.
z Check where there are any damages caused by transportation. Please do not apply the power, and do
contact Teco’s sales representatives if any of the above problems happened.
0-1
Chapte 1 Safety Precautions
Chapter 1 Safety Precautions

1.1 Operation Precaution
1.1.1 Before Power ON
Caution
The line voltage applied must comply with the inverter’s specified input voltage.
Danger
Make sure the main circuit connections are correct. L1(L), L2 and L3(N) are power-input
terminals and must not be mistaken for T1, T2 and T3. Otherwise, the inverter might be
damaged.
Caution
z To avoid the front cover from disengaging, do not pull the cover during handling for
the heat sink should be fallen off. Accident falling down will damage the inverter or
injure to person, which should be avoided.
z To avoid the risk of fire, do not install the inverter on a flammable object. Install it on
nonflammable object such as metal.
z If several inverters are placed in the same control panel, add extra heat sink to keep
the temperature below 40 to avoid overheat or fire.
z When removing or installing the operator, turn OFF the power first, and manipulate
the operator following the instruction of the diagram to avoid operator error or no
display caused by bad contact.
Warning
This is a product of the restricted sales distribution class according to IEC 61800-3. In a
domestic environment this product may cause radio interference in which case the user
may be required to take adequate measures.
1-1
1.1.2 During Power ON
Danger
z Do not plug or unplug the connectors on the inverter when electrified to avoid the
control panel damage resulting from erratic transition voltage surge due to contact
bounce.
z When momentary power loss is longer than 2 seconds (the larger of horse power, the
longer of time), the inverter does not have enough storage power to control the circuit;
Therefore, when power is regenerated, the operation of the inverter is based on the
setup of 1-00 / 2-05 and the condition of external switch, this is considered to be
「restart」in the following paragraphs.
z When the momentary power loss is short, the inverter still has enough storage power
to control the circuit. Therefore, when power is regenerated, the inverter will
automatically restart depending on the setup of 2-00/2-01.
z When restart the inverter, the operation of the inverter is based on the setup of 1-00
and 2-05 and the condition of external switch (FWD/REV button). Attention: the
start operation is irrelevant with 2-00/2-01/2-02/2-03.
1. When 1-00=0000, the inverter will not automatically run after restart.
2. When 1-00=0001 and the external switch (FWD/REV button) is OFF, the inverter
will not run after restart.
3. When 1-00=0001, the external switch (FWD/REV button) is ON, and 2-05=0000,
the inverter will run automatically after restart. Attention: In the sake of safety,
please turn off the external switch (FWD/REV button) after power loss to avoid
underling damage to the machine and the human body after sudden regeneration of
power.
z To ensure the safety of people and machine, please refer to the description and
suggestion of 2-05
1.1.3 Before Operation
Danger
Make sure the model and capacity are the same as those set by 15-0.
Caution
The inverter will flash the power voltage set by 0-07 for 5 seconds when applying power.
1-2
1.1.4 During Operation
Danger
Do not engage or disengage the motor during operation. Otherwise, the over-current will
cause the inverter to disconnect or the main circuit to burn.
Danger
z To avoid electric shock, do not take the front cover off during electrifying
z The motor will restart automatically after stop when auto-restart function is on. In this
case, do not get close to the machine.
z Note: The stop switch is different from the usage of the emergency stop switch. It must
be set first to be effective.
Caution
z Do not touch heat-generating components such as heat sink and braking resistor.
z The inverter can drive the motor running from low speed to high speed. Verify the
allowable capacities range of the motor and the mechanism.
z Note the settings related to the braking reactor.
z Do not check signals on circuit boards while the inverter is running.
Caution
It is after 5 minutes that disassembling or checking the components could be performed as
power supply OFF and the indicator turned off.
1.1.5 During Maintenance
Caution
The inverter should be used in a non-condensed environment with temperature from –10
to +40 and relative humidity of 95% non-condense.
Caution
When the inverter top cover has removed, it can be used in a non-condensed environment
with temperature from –10 to +50 and relative humidity of 95%, but the environment
should be free from water and metal dust.
1-3
Chapter 2 Description of models
Chapter 2 Definition of model
Inverter model → MODEL： JNTHBCBA0001AC-UF
Input voltage → I/P： AC 1 PH
200~240V 50/60Hz
Output specifications→ O/P： AC 3PH 0~264V

1.2 KVA 3.1 A
TECO ELECTRIC & MACHINERY CO., LTD.
JNTH BC BA 0001 AC - U F
Series:
Keypad Panel Horsepower： UL Approval：
BC：LED R500：0.5 HP U：Yes

Noise Filter：
BG：LCD 0001：1.0 HP
-：None
0002：2.0 HP Power supply:
AC：Single phase 220V

0003：3.0 HP
BC：Three phase 220V

Enclosure： 0005：5.0 HP
BE Th h 440V
BA：Open chassis type 7R50：7.5 HP
0010：10 HP
2-1
Chapter 3 Ambient Environment and Installation

3.1 Environment
The environment will directly affect the proper operation and the life span of the inverter, so install the
inverter in an environment complying with the following conditions:
z Ambient temperature: -10oC ~ +40oC; without cover: -10oC ~ +50oC

z Avoid exposure to rain or moisture. z Avoid direct sunlight.
z Avoid oil mist and salinity. z Avoid erosive liquid and gas.
z Avoid dust, bats, and small metal pieces. z Keep away from radioactive and
flammable materials.
z Avoid electromagnetic interference (soldering machine, power machine).
z Avoid vibration (punching machine). Add a vibration-proof pad if the situation cannot be
avoided.
z If several inverters are placed in the same control panel, add extra heat sinks to keep the
temperature below 40oC.
Air exchanging fan Air exchanging fan
Inside the power Inside the

distributor power
Distributor Inside the
power
distributor
(Correct configuration) (Incorrect configuration) (Correct configuration) (Incorrect configuration)

z Place the front side of the inverter onward and top upward to in favor of heat sink.
z Install the inverter according to the following figures: (take the dustproof cover off in favor of heat
sinking if it is installed in a box or the environment allows to do so)
Air convection
-10oC - +40oC
(a) Front view (b) Side view
3-1
3.2 Environmental precautions
Do not use the inverter in an environment with the following conditions:
Oil
Direct sunlight Corrosive gas and liquid Oil Mist
Salt
Wind, rain, and water

Salt drops may get into Iron filings, dust
Strong vibration Extreme low temperature Excessive high temperature
Electromagnetic wave and

ultra high wave Radioactive materials Inflammable materials
(Near an electric welding machine)
3-2
3.3 Inflammable materials

3.3.1 Notice for wiring
A. Screwdriver torque:
Wiring with a screwdriver or other tools and follow the torque listed below:
Securing torque
Horsepower Power source Nominal torque for TM1 terminal
0.5/1/2(3φ) 200-240V 0.59/0.08 7.10/8.20
1/ 2 380-480V (LBS-FT / KG-M) (LBS-IN/KG-CM)
2(1φ)/3/5/7.5/10 200-240V 1.5/0.21 18.00/20.28
3/ 5/ 7.5/ 10/15 380-480V (LBS-FT/KG-M) (LBS-IN/KG-CM)
15/20/25 200-240V 1.84/0.3 22.1/30
20/25/30 380-480V (LBS-FT / KG-M) (LBS-IN/KG-CM)
30/40 200-240V 4.42/0.66 53.1/66
40/50/60/75 380-480V (LBS-FT/KG-M) (LBS-IN/KG-CM)
B. Power wires:
Power wires are connecting to L1, L2, L3, T1, T2, T3, P, BR and P1. Choose wires in
accordance with the following criteria:
(1) Use copper wires only. Deciding diameters of wires should be based on rating working at
105oC.
(2) For rating voltage of wires, the minimum voltage of 230VAC type is 300V, and 460VAC
type is 600V.
(3) For safety reason, the power wires should be fixed by type terminal.
C. Control wires:
Control wires are wires connecting to TM2 control terminal. Choose the wire in accordance with
the following criteria:
(1) Use copper wires only. Deciding diameters of wires should be based on rating working at
105oC.
(2) For rating voltage of wires, the minimum voltage of 230VAC type is 300V, and 460VAC
type is 600V.
(3) To avoid noise interference, do not route the control wires in the same conduit with power
wires and motor wires.
D. Nominal electrical specifications of the terminals Block:

The following list is nominal values of TM1:
Horsepower Power source Volts Amps
0.5/1/ 2(3φ) 200-240V
15A
1/ 2 380-480V
5/ 7.5/ 10 200-240V
40A
2(1φ)/3/ 5/ 7.5/ 10/15 380-480V
15/20/25 200-240V 600 80A
20/25/30 380-480V 60A
30 200-240V
100A
40/50 380-480V
40 200-240V
150A
60/75 380-480V
Note: Nominal values of input and output signals (TM2) – follow the specifications of class 2
wiring.
3-3
E. Fuse types
Drive input fuses are provided to disconnect the drive from power in the event that a component fails in the
drive’s power circuitry. The drive’s electronic protection circuitry is designed to clear drive output short circuits
and ground faults without blowing the drive input fuses. Below table shows the 7300CV input fuse ratings.
To protect the inverter most effectively, use fuses with current-limit function.
RK5, CC/T TYPE FUSE FOR 7300CV
220V class(1φ)
100% CONT Max.RK5 Max.CC or T
JNTHBCBA- HP KW KVA
Output AMPS (A) FUSE Rating(A) FUSE Rating(A)
R500AC 0.5 0.4 1.2 3.1 10 20
0001AC 1 0.75 1.7 4.5 15 30
0002AC 2 1.5 2.9 7.5 20 40
0003AC 3 2.2 4.0 10.5 25 50
220V class(3φ)
JNTHBCBA HP KW KVA
R500BC 0.5 0.4 1.2 3.1 8 10
0001BC 1 0.75 1.7 4.5 12 15
0002BC 2 1.5 2.9 7.5 15 20
0003BC 3 2.2 4.0 10.5 20 30
0005BC 5 3.7 6.7 17.5 30 50
7R50BC 7.5 5.5 9.9 26 50 60
0010BC 10 7.5 13.3 35 60 70
0015BC 15 11.0 20.6 48 80 100
0020BC 20 15.0 27.4 64 100 125
0025BC 25 18.5 34.0 80 125 150
0030BC 30 22.0 41.0 96 160 200
0040BC 40 30.0 54.0 130 200 250
440V class(3φ)
JNTHBCBA- HP KW KVA
0001BE 1 0.75 1.7 2.3 6 10
0002BE 2 1.5 2.9 3.8 10 15
0003BE 3 2.2 4.0 5.2 10 20
0005BE 5 3.7 6.7 8.8 20 30
7R5BE 7.5 5.5 9.9 13 25 35
0010BE 10 7.5 13.3 17.5 30 50
0015BE 15 11.0 20.6 25 50 60
0020BE 20 15.0 27.4 32 60 70
0025BE 25 18.5 34.0 40 70 80
0030BE 30 22.0 41.0 48 80 100
0040BE 40 30.0 54.0 64 100 125
0050BE 50 37.0 68.0 80 125 150
0060BE 60 45.0 82.0 96 150 200
0075BE 75 55.0 110.0 128 200 250
*Fuse ratings are based upon 300V fuses for 230V inverter, and 500V for 460V inverters
3-4
Notice
z To avoid shock hazards, do not touch any electrical component when the power is applied or
just after five minutes the power plug is unplugged. The other action should be performed
after the charge indicator went off.
z Do not perform wiring on the inverter while it is still electrified. Disregard of this notice
could cause serious injure or death to persons.
This product is designed to use in Pollution Degree 2 environment or equivalent environments.
3.3.2 Applicable specification of magnetic contactor and wires

Molded-case circuit breaker/magnetic contactor
z Teco bears no responsibility to service for failures caused by the following conditions:
(1) A molded-case circuit breaker is not installed, or an improper or overrated breaker is
used, between the power source and the inverter.
(2) A magnetic contactor, a phase capacitor, or a burst absorber is connected between the
inverter and the motor.
7300CV model JNTHBCBA□□□□AC / JNTHBCBA□□□□BC
R500 0001 0002 0003 0005 7R50 0010 0015 0020 0025 0030 0040
Molded-case
TO-50E TO-50E TO-50E TO-50E TO-50E TO-50E TO-100S TO-100S TO-100S TO-225S TO-225S TO-225S
circuit breaker 10A 20A 30A 30A 30A 50A 60A 100A 100A 150A 175A 175A
made by Teco
Magnetic
contactor (MC) CN-11 CN-16 CN-18 CN-25 CN-50 CN-65 CN-80 CN-100 CN-125
made by Teco
Main circuit Wire Wire Wire
Wire gauge Wire gauge Wire gauge 5.5 Wire gauge
terminals gauge gauge gauge
2.0 mm2 3.5 mm2 mm2 22 mm2
(TM1) 14 mm2 38mm2 60mm2
Signal terminals
Wire gauge 0.75mm2 ( # 18 AWG)
(TM2)
JNTHBCBA□□□□BE
7300CV model
0001/ 0002/ 0003/ 0005 7R50 0010 0015 0020 0025 0030 0040 0050 0060 0075
Molded-case circuit TO-50E TO-50E TO-50E TO-50E TO-100S TO-100S TO-100S TO-100S TO-125S TO-225S TO-225S
breaker made by Teco 15A 20A 30A 50A 50A 75A 100A 100A 125A 175A 175A
Magnetic contactor
CN-11 CN-16 CN-18 CN-25 CN-35 CN-50 CN-50 CN-65 CN-80 CN-100 CN-125
(MC) made by Teco
Wire Wire Wire Wire
Main circuit terminals Wire gauge Wire gauge Wire gauge
Wire gauge 2.0mm2 gauge gauge gauge gauge
(TM1) 3.5mm2 8mm2 22mm2
5.5mm2 14mm2 38mm2 60mm2
Signal terminals (TM2)

Wire gauge 0.75mm2 ( # 18 AWG), terminal screw M3
z Use three-phase cage induction motor with capacity suitable for the inverter.
z One inverter is driving several motors, the total current of all motors running simultaneously
must be less than the rated current of the inverter, and each motor has to be equipped with a
proper thermal relay.
z Do not add capacitive component, such as a phase capacitor, LC or RC, between the inverter
and the motor.
3-5
3.3.3 Precautions for peripheral applications:

Power supply:
z Make sure the voltage applied is correct to avoid
Power damaging the inverter.
z A molded-case circuit breaker must be installed
between the AC source and the inverter
Molded-case circuit breaker:
z Use a molded-case circuit breaker that conforms to
Molded-case the rated voltage and current of the inverter to
circuit breaker control the power ON/OFF and protect the inverter.
z Do not use the inverter as the switch for run/stop
switch.
Leakage breaker:
z Install a leakage breaker to prevent error operation
Magnetic caused by electric leakage and to protect operators
contactor z Setting current should be 200mA or above and the
operating time at 0.1 second or longer to prevent
malfunction.
Magnetic contactor:
AC reactor z Normal operations do not need a magnetic contactor.
for power But a contactor has to be installed in primiary side
improvement when performing functions such as external control
and auto restart after power failure, or when using
brake controller.
z Do not use the magnetic contactor as the run/stop
Install fast switch of the inverter.
action fuse AC reactor for power improvement:
z When inverters below 200V/400V 15KW are
supplied with high capacity (above 600KVA) power
source or an AC reactor can be connected to
Input noise improve the power performance.
Install fast action fuse:
filter z To ensure the safety of peripheral devices, please
install the fast action fuse. Regarding the
specification, please refer to P3-4.
Input noise filter:
7300CV inverter z A filter must be installed when there are inductive
load around the inverter
Inverter:
z Input power terminals L1, L2, and L3 can be used in
Ground any sequence regardless of phases.
z Output terminals T1, T2, and T3 are connected to U,
V, and W terminals of the motor. If the motor is
reversed while the inverter is forward, just swap any
Three-phase two terminals of T1, T2, and T3.
cage motor z To avoid damaging the inverter, do not connect the
input terminals T1, T2, and T3 to AC power.
z Connect the ground terminal properly. 200 V series:
class 3 grounding, <100Ω; 400 V series : <10Ω.
Ground
3-6
Make external connections according to the following instruction. Check connections after
wiring to make sure all connections are correct. (Do not use the control circuit buzzer to check
connections)
z The inverter uses dedicated power line A general noise filter may not provide
rightful results
z Add a noise filter or separation transformer whenter

shares the power line with other machines.
z the inverter shares the power line with other machines.
(A) Main circuit’s wiring must separate from other high voltage or high current power line to
avoid noise interference. Refer to the figures below:
z A noise filter in the output of the main circuit can suppress conductive noise. To prevent radiative noise,
the wires should be put in a metal pipe and distance from signal lines of other control machines for more
than 30 cm.
MCCB Metal Box

Metal Pipe
Power Supply
Noise 7300CV Noise
Filter Filter
above
Signal Wire
Controller
3-7
z When the connection between the inverter and the motor is too long, consider the
voltage drop of the circuit. Phase-to-phase voltage drop (V) =
3 ×resistance of wire (Ω/km)×length of line (m)×current×10-3. And the number of
carriers must be adjusted based on the length of the line.
The length of the line between
Below 25m Below 50m Below 100m Over 100m
the inverter and the motor
Number of carriers allowed Below 16KHz Below 12KHz Below 8KHz Below 5KHz
Settings of 3-22parameter 16 12 8 5
(B) The wiring of the control circuit must be separated and routed away from the main circuit
control line or other high voltage or current power lines to avoid noise interference
z To avoid error actions caused by noise interference, shield the control circuit wiring
with a twisted wire, and connect the shielded wire to a ground terminal. Refer to the
figure below.
The wiring distance should not exceed 50 m.
Protective
Shielding Wire
To ground terminal Do not connect this end

(refer to instructions of
filter wiring Wrapped with insulating
(C) Ground the ground terminal of the inverter properly. For 200V class ground 100Ω or less;
for 400V class ground 10Ω or less.
z Ground wiring is based on the electrical equipment technical basis (AWG). The shorter,
the better.
z Do not share the ground of the inverter to other high current loads (welding machine,
high power motor). Connect the terminals to ground respectively.
z Do not make a loop when several inverters share a common ground point.
(a) Good (b) Good (c) Bad

(D) To ensure maximum safety, use proper wire gauges (AWG) for the main power circuit and
control circuit according to relative regulations.
(E) After wiring, check that the wiring is correct, wires are intact, and terminal screws are
secured.
3-8
3.4 Specifications
3.4.1 Products Individual Specifications
Single phase, 200-240V model
J N T H BC B A□ □ □ □ AC - U ( F ) R500 0001 0002 0003
Horsepower(HP) 0.5 1 2 3
Suitable Motor Capacity(KW) 0.4 0.75 1.5 2.2
Rated Output Current(A) 3.1 4.5 7.5 10.5
Rated Capacity(KVA) 1.2 1.7 2.9 4.0
Max. Input Voltage Sing le Phase: 200 ~240V +10% -15%，50 /60H Z ± 5 %
Max. Output Voltage Th ree Phases: 0 ~240V
Input Current(A) 8.5 12 16 23.9
Net Weight(KG) 1.2(1 .3) 1.2(1 .3) 1.5(1 .8) 1.9(2 .3)
Allowable momentary power loss
1.0 1.0 2.0 2.0
time (second)
Three phases, 200 – 240V model
0 00 0 00 0 00 0 01 0 01 0 02 0 02 0 03 0 04
JNTHBC BA□□□□BC-U R500 0 00 5 7 R 50
1 2 3 0 5 0 5 0 0
Horsepower(HP) 0.5 1 2 3 5 7.5 10 15 20 25 30 40
Suitable Motor Capacity(KW) 0.4 0.75 1.5 2.2 3.7 5.5 7.5 11 15 18.5 22 30
Rated Output Current(A) 3.1 4.5 7.5 10.5 17.5 26 35 48 64 80 96 130
Rated Capacity(KVA) 1.2 1.7 2.9 4.0 6.7 9.9 13.3 20.6 27.4 34 41 54
Max. Input Voltage Th ree Vo ltag e : 200 ~240V +10% -15% ，50 /60H Z ± 5 %
Max. Output Voltage Th ree Vo ltag e : 0 ~240V
Input Current(A) 4.5 6.5 11 12.5 20.5 33 42 57 70 85 108 138
Net Weight(KG) 1.2 1.2 1.2 1.75 1.9 5.6 5.6 15 15 15 33 34
Allowable momentary power
1.0 1.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0
loss time (second)
Three phases, 380 – 480V model
0 00 0 00 0 00 0 00 7 R 5 0 01 0 01 0 02 0 02 0 03 0 04 0 05 0 06 0 07
J N T H BC B A□ □ □ □ B E-U ( F )
1 2 3 5 0 0 5 0 5 0 0 0 0 5
Horsepower(HP) 1 2 3 5 7.5 10 15 20 25 30 40 50 60 75
Suitable Motor Capacity(KW) 0.75 1.5 2.2 3.7 5.5 7.5 11 15 18.5 22 30 37 45 55
Rated Output Current(A) 2.3 3.8 5.2 8.8 13.0 17.5 25 32 40 48 64 80 96 128
Rated Capacity(KVA) 1.7 2.9 4.0 6.7 9.9 13.3 19.1 27.4 34 41 54 68 82 110
Max. Input Voltage Th ree Vo ltag e :380~480V +10% -15%， 50 /60H Z ± 5 %
Max. Output Voltage Th ree Vo ltag e : 0 ~480V
Input Current(A) 4.2 5.6 7.3 11.6 17 23 31 38 48 56 75 92 112 142
1.2 1.2 1.8 1.8 5.6 5.6 5.6
Net Weight(KG) 15 15 15 33 33 50 50
(1.3 ) (1.3 ) (2.2 ) (2.2 ) (6.6 ) (6.6 ) (6.6 )
Allowable momentary power loss
1.0 1.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0
time (second)
NOTE1: DC Reactor is built-in for 30hp above in 200V class series.
NOTE2: DC Reactor is built-in for 40hp above in 400V class series.
3-9
3.4.2 General Specifications
Item 7300CV TYPE
Control Mode V/F or Current Vector Control
Range 0.1~650.0 Hz
Start control torque 150%/1Hz (Current Vector)
Speed control range 1:50 (Current Vector)
Speed Control Precision ±0.5% (Current Vector)

Frequency Control
Setting resolution Digital: 0.01Hz( Note *1 ): Analog: 0.06Hz/ 60Hz(10bits)
Keypad setting Set directly with▲▼ keys or the VR on the keypad
Four digital LED (or 2×16 LCD) and status indicator; display
frequency/ speed/ line speed/ DC voltage/ Output voltage/ Current/
Display Function
Rotation direction/ Inverter parameter/ Trouble Log/ Program
Version
1. External variable resistor/ 0-10V/ 0-20mA/ 10-0V/ 20-0mA
2. Performs up/down controls, speed control or automatic procedure
External signal setting control with multifunctional contacts on the terminal block
(TM2)
Frequency Limit Function Respectively setting upper/lower frequency limits and three-stage
prohibited frequencies
Carrier frequency 2 ~ 16 kHz
V/F pattern 18-fixed patterns, 1 programmable pattern
Two-stage Acc/Dec time (0.1 – 3,600 seconds) and two-stage S

Acc/Dec control
curves (refer to descriptions on 3-05)
Multifunctional analog 6 functions (refer to description on 8-00/8-01)
General Control
output
Multifunctional input 30 functions (refer to description on 5-00~5-06)
Multifunctional output 16 functions (refer to description on 8-02~8-03)
Digital Input Signal NPN (SINK) / PNP (SOURCE) toggle

Momentary Power Loss Restart, Speed Search, Overload Detection, 8
preset speeds ( PLC use 16 preset speeds). Acc/Dec Switch (2
Stages), S Curves, 3-wire Control, PID control, torque boost, Slip
Other Function
Compensation, Frequency Upper/ Lower Limit, Auto energy saving,
Modbus slave and PC/PDA Link, Auto Restart, Built-in Simple PLC
Function.
3-10
Item 7300CV TYPE
Communication Control 1. Control by RS232 or RS485
2. One to one or One to more (RS485 ONLY) control.
3. BAUD RATE/STOP BIT/PARITY/bit can be set
Braking Torque About 20﹪, the model built-in braking transistor and connected
braking resistor is 100%
Operation temperature -10 ~ 50℃(note 2)
Storage temperature -20 ~ 60℃
Humidity 0 – 95% Relative Humidity(Non-condense)
Height Below 1000M

Vibration Sustention 1G (9.8m/s2 )
EMC Comply with requirement EN 61800-3 (with optional Filter).
LVD Comply with requirement EN 50178
Enclosure IP00 or IP20 ( NEMA 1 by external box attached)
Safety Level UL 508C
The relays to protect the motor (the curve can be set) and the inverter
Overload protection
(150 % / 1min)
FUSE protection The motor stops after FUSE melt
Over Voltage 200V class：DC Voltage＞410V 400V class：DC Voltage＞820V

Protective Functions
Under Voltage 200V class：DC Voltage＜190V 400V class：DC Voltage＜380V
Momentary Power Stop for more than 15ms-power-loss can be restarted with spin start
Loss Restart after momentary power loss in Max 2 sec.
Stall Prevention Stall prevention for Acceleration/ Deceleration/ Operation.
Short-circuit output Electronic Circuit Protection

terminal
Grounding Fault Electronic Circuit Protection
Protection for overheating of heat sink, over torque detection, error

Other Function contact control, reverse restriction, restrictions for direct start after
power up and error recovery, parameter lock up.
Note 1: The setting resolution of above 100Hz is 0.1Hz when controlled with operation keypad,
and 0.01 Hz when controlled using computer PC or programmable controller (PLC).
Note 2: –10 ~ 50℃ in distributor (without dustproof cover)
–10 ~ 40℃ outside distributor (with dustproof cover)
3-11
Note 3: 220V 15HP and above capacity are not CE complied
3-12
3.5 Wiring diagram 7300CV series inverter
Wiring diagram I:
DC Braking
reactor Resistor(note1)
Molded-case circuit breaker

Magnetic Install fast BR
P P1
MCCB contactor action fuse (Note2) (Note2) (Note2) Induction
MC
(
L1(R) T1(U) motor
AC
Power Power T2(V)
(
Power L2(S)
input output
source
( L3(T) T3(W)
200V:Class 3 ground
PE
ON-OFF 400V: Special ground
MC
Burst absorber
CON 2
RS485
TM2
RS232 (Option Card)
Multifunction input terminal
Digital
Control Memory Card
Forward/stop or run/stop S1
panel
Reverse/stop or reverse/forward S2
S3 CON1
Speed control S4
S5
Common point for PNP input 24V
PE R1A
R1B
Common point for NPN COM

R1C
Reset /Error recovery S6/AI2
(Multifunction input terminal) Multifunctional output terminals
+ 10V 250VAC/1A (30VDC/1A)
Frequency indicator P
AIN
R2A
P
device - COM R2B
+ FM+
FM
V NPN SW2: AIN 0~10V/0~20mA selective
Frequency indicator - COM SW3: S6/AI2 0~10V/0~20mA selective
SW2 SW3 SW1
0~10VDC or 2~10V/4~20mA (after Ver.2.3)
PNP I POSITION: 0~20mA signal
I
V POSITION: 0~10V signal
SW1: NPN/PNP selective
Note 1: Please refer to description of main circuit terminals (P1, BR) and specification of braking
resistor for value selection.
Note 2: Above wiring diagram refers for 0.4~1.5KW at 220V and 0.75~1.5KW at 440V only.
3-13
Wiring diagram II:
Note 1: Please refer to description of main circuit terminals (P1, BR) and specification of braking
resistor for value selection.
Note 2: Above wiring diagram refers for 2.2~7.5KW at 220V and 2.2~11KW at 440V only.
3-14
3.6 Description of terminals of troubleshooting inverter
Descriptions of main circuit terminals
Symbol Description
R / L1 ( L )
Main power input Single-phase: L/N
S / L2 Three-phase: L1/L2/L3
T / L3 ( N )
P1 Braking resistor or connecting terminal: Used in cases where the inverter
For
frequently disconnects due to large load inertia or short deceleration time
BR 220V:0.5~10HP,
(refer to specifications of braking resistor)
440V:1~15HP
P1/ P DC reactor connecting terminals
B1/P z B1 /P- Ө : DC pow er supp ly inpu t -
B2 B1 /P- B2 : Ex ternal br aking r e sistor
Ө Fo r 220V : 15 ~20HP and 440V : 20HP z ⊕- Ө : D C pow er supp ly inpu t or Exte rna l
br ak ing un it. Check Chapter 6.3
⊕ -
Fo r 220V : 25 ~40HP and 440V : 25~75HP
U / T1
V / T2 Inverter outputs
W / T3
Descriptions of 7300CV control circuit terminals
Symbol Description
R2A
Multifunctional terminal – Normal open Contact rated capacity:
R2B
(250VAC/1A or 30VDC/1A)
R1C Common contact
Contact using description:(refer to 8-
R1B Normal close contact Multifunctional output terminals 02, 8-03)
R1A Normal open contact
10V Frequency knob (VR) power source terminal (pin 3)
Analog frequency signal input terminal or multifunction input terminals S7 (H level:>8V, L level:<2V,
AIN PNP only) (refer to5-06 description)
Common contact for S1~S5 (S6, S7) in PNP (Source) input. Shift to PNP position (refer to wiring
24V diagram) of SW1 when used PNP input
1. Common contact and analog input /output signal for S1~S5 in NPN (Sink) input.
COM Shift to NPN position (refer to wiring diagram I) of SW1 when used NPN input.
24G 2. AGND for AIN,AI2 and FM+ (analog input /output signal) & 24G for S1~S6 (digital input /output
AGND signal in NPN (Sink) input). Shift to NPN position (refer to wiring diagram II) of SW1 when used
NPN input.
The positive analog output for multifunction (refer to 8-00 description), the signal for output terminal is
FM+ 0-10VDC (below 2mA).
．220V: 15 ~ 20 HP 440V: 20HP
R/L1 S /L2 T/L3 B1/P B2 U/T1 V/T2 W/T3

Power Dynamic To Motor
．220V: 25 ~ 40HP 440V: 25~75HP
R/L1 S/L2 T/L3 ⊕ U/T1 V/T2 W/T3
3-15
Symbol Function Description

S1
S2 Multifunction input terminals(refer to 5-00 ~ 5-04 description)
S3 (S5 = Encoder input terminal, the Encoder voltage range: 19.2V~24.7V)
S4
S5
1. Multifunction input terminals (Digital terminal H level:>8V, L level:<2V, PNP only) or analog input
terminal AI2(0 ~10Vdc /4 ~20 mA) ( refer to 5-05 description)
S6 2. The V2 .9 v ersion (con tains) abov e the ed ition, S6 on ly is the Multi-function input
terminal use, A I2 h ave rep laced S6 to tak e analog inpu t use. (Above wiring diagram
refers for 2.2~7.5KW at 220V and 2.2~11KW at 440V only.)
Descriptions of SW function
SW2/SW3 Type of external signal Remarks

V
0~10VDC analog signal
(1) External control is available as

1-06=0002
V (2) Factory setting is voltage input
0~20mA analog signal
SW1 Type of external signal Remarks
NPN (SINK) input
PNP (SOURCE) input Factory default
3-16
3.7 Outline Dimensions
(1) Frame1 : Single phase JNTHBCBA__AC: R500, 0001
Three phase JNTHBCBA__BC/BE: R500, 0001, 0002
(2) Frame2 : Single phase JNTHBCBA__AC: 0002, 0003
Three phase JNTHBCBA__BC/BE: 0003, 0005
4-Ø5.5
B
A
C
D
E
F
G
Unit : mm/inch
LENGTH
A B C D
MODEL
Frame 1 163/6.42 150/5.9 78/3.07 90/3.54
Frame 2 187.1/7.36 170.5/6.71 114.6/4.51 128/5.04
LENGTH
E F G
MODEL
Frame 1 147/5.79 141/5.55 7/0.28
Frame 2 148/5.83 142.1/5.59 7/0.28
3-17
(3) Frame3 : Three phase JNTHBCBA__BC: 7R50, 0010
JNTHBCBA __BE: 7R50, 0010, 0015
4-Ø5.5
B
A
C
D
E
F
Unit : mm/inch
LENGTH
A B C D E F
MODEL
Frame 3 260/10.24 244/9.61 173/6.81 186/7.32 195/7.68 188/7.4
3-18
(4) Frame4 : Three phase JNTHBCBB __ BC: 0015, 0020, 0025
JNTHBCBB __ BE: 0020, 0025, 0030
E
D 4-Ø7.0
A
B
C
F
(5) Frame5 : Three phase JNTHBCBA __ BC: 0030, 0040
JNTHBCBA __ BE: 0040, 0050
(6) Frame6 : Three phase JNTHBCBA __ BE: 0060, 0075
E 4-Ø10
C
A
B
F
（Open Chassis Type－IP00）

Unit : mm/inch
LENGTH
MODEL A B C D E F
Frame4 360/14.2 340/13.4 10/0.4 245/9.6 265/10.4 247.5/9.7
Frame5 553/21.8 530/20.9 10/0.4 210/8.3 269/10.6 303.6/12
Frame6 653/25.7 630/24.8 10/0.4 250/9.8 308/12.1 308.6/12.1
3-19
3-20
Chapter 4 Software Index
4.1 Keypad Description
4.1.1Keypad Display and Operation Instruction
1. SEQ LED：1_00 =1/2/3, LED Lit.
2. FRQ LED：1_06 = 1/2/3/4, LED Lit
3. FWD LED：Forward Direction, LED action(Flash in stop, Keep Lit in operation).
4. REV LED：Reverse Direction, LED action(Flash in stop, Keep Lit in operation).
5. Four action of FUN、Hz/RPM、VOLT、AMP LED and display of four 7-segment display, refer to
operation description of the keypad.

6. LCD keypad without FUN, Hz/RPM, VOLT, AMP LED and FREQ.SET knob.
Caution
To avoid impairing the keypad, do not operate it with screwdriver or sharp and hard tool.
Remote/Local Mode
․Local mode – Operation Command by RUN/STOP key on keypad

4-1
– Frequency Command by ▲▼ key on keypad
․Remote mode – Operating Command by 1-00
– Frequency Command by 1-06
To Change the Remote/Local mode, you must push FWD/REV and《/RESET key at the same time.
The Remote /Local mode of change can used in STOP mode, it can’t used in Run mode.
4-2
4.1.2 Operation Instruction of the keypad
Power On ● LED Light Lit

:LED Light Flash
Power Voltage (*1)
5 second later or Enter operation signal or Press DSP to modify frequency.
Frequency/Speed
HZ/RPM v < Frequency/Speed/
/Line Speed HZ/RPM
^ Line Speed
RUN/STOP (*3)
Frequency/Speed
HZ/RPM
/Line Speed READ/
ENTER (*2)
DSP
Selecting the READ/

parameter group ENTER
FUN
v ☉ Parameter Setting
^ FUN
Selecting the
DSP
FUN parameter group
DSP READ/
ENTER
END
DSP
Output Voltage DSP DC Voltage

VOLT VOLT
DSP
Build-in PLC Status DSP
Output Current AMP
(*4)
*1：The inverter will flash the current setting of 0-07 (power supply voltage) after power up.
*2：4-04, 4-05 determines the displaying of frequency, speed or line speed.
*3：It is not necessary to press ENTER key when stopped for modification. Refer to example 1, 2.
4-3
4.1.3 Operation Instruction of the LED keypad
Power On
● : LED Light Lit
: LED Light Flash
5 seconds later or Enter operation signal or Press DSP to modify the display frequency.
HZ/RPM ‧
^ v ＜
HZ/RPM ‧
RUN/STOP
HZ/RPM ‧ READ/
ENTER
READ/
ENTER
FUN ☉
DSP — FUN
^ v ^ v
DSP
☉
FUN — FUN
READ/
ENTER
DSP
DSP
VOLT VOLT
DSP
DSP
AMP
4-4
4.1.4 Operation Instruction of the LCD keypad
Power On
Power Source
220 V
5 second later or Enter operation signal or Press DSP to modify frequency
Master Freq.
60.00 Hz ^ v ^ ＜ Setting Freq.
060.00Hz
RUN/STOP
READ/
Output Freq.
ENTER
50.99 Hz
DSP
READ/
00- 00=Vector(CT) 00-06= 0
ENTER
Control Mode Disabled
^ v ^ v
00- 06=Disabled DSP 00-06= 1
Auto Tuning Enabled
END READ/
ENTER
DSP DSP
Output Voltage DSP DC Bus Voltage

220V 311V
DSP
PLC State
DSP Output Current
Stop
3.1 Amp
4-5
4.1.5 Keypad Operating Example
4-6
Example4. Modify the Frequency in Operating

Example4. Modify the Value of Parameter
Example 5. Operation Control
6-00
6-00
Power On
FWD RUN FWD RUN

REV STOP REV STOP
FWD LED ~ { { ● ~
REV LED { ~ ● { {
●: LED Lit ~: LED Flash {: LED Go Out
4-7
4.2 Control Mode Selection

7300CV Series inverter has three control modes:
1. General Vector Control Mode
2. VT Vector Control Mode (Special for Blower, Pump).
3. V/F Control Mode。
The user can choose these modes with the digital keypad according to the application characteristics.
The factory setting is general vector control mode. Before operation, please set the control mode and
the relative parameters of the motor in accordance with the following flow chart. (The Vector control
mode only suits for the inverter with same capacity comparing to the motor, or a grade bigger or
smaller one).
Setting procedure of
control mode
Vector Control
Control mode
V/F Control
Control mode selection 0-00=2 Control mode selection
0-00=0
Set the following parameter: 0-00=1
V/F Pattern 10-0
Torque Boost 10-1
Set the following parameter:
Motor no load current 10-2 (<=0-02)
Motor rated voltage 0-01
Motor Rated Slip 10-3
Motor rated current 0-02
Max output frequency 10-4
Motor power 0-03
Max output voltage 10-5
Motor rated Speed 0-04
Medium output Frequency 10-6
Motor rated Frequency 0-05
Medium output voltage 10-7
Power Voltage
Min output frequency 10-8
Min output voltage 10-9 Perform Auto tuning (0-06=1)
Suitable motor capacity 0-02 (OL1 reference index)
End
※Note:
1. Use V/F Control Mode:

(1) Use one inverter to drive several motors simultaneously
(2) Motor’s nameplate is unknown or motor ’s specifications are too special, it will
cause Auto-tuning fault.
(3) Specification of inverter and motor differ more than 1 class.
2. One inverter drives several motors (Only V/F mode available), set the motor parameter complying
with the following rules:
(1). As for the current, sum the rated current of all motors.
(2). As for others, input correct VF Pattern parameter (10-4~10-9).
3. When the nameplate of the motor is unknown, the inverter will set the internal parameter
according to the standard TECO motor.
4-8
4. When parameter 0-00 does set to 2, the keypad will display ‘Err2’ in performing Auto tuning.
5. When VF control, 0-01~0-05 max. & min. value by the TECO standard motor specification
limit(one more & one less level). When VF control, no district.
4.3 7300CV Programmable Functions List
Parameter
Description
Group No.
0- Drive Operation Mode
1- Start/Stop and Frequency Control Modes
2- Manual/Automatic Restart Modes
3- Operating Parameters
4- Digital Display Operation Mode
5- Multifunction Input Terminals (MFIT)
6- Jog, and Preset (MFIT) Speed Setting on Keypad
7- Analog Input Signal Operation
8- Multifunction Output Relays and Output Signal Operation
9- Drive and Load Protection Modes
10- Volts/Hz Pattern Operation Mode
11- PID Operation Mode
12- PID "Limits" and "Out of Range" Mode
13- Communication Mode
14- Motor Auto-Tuning Parameters
15- Drive Status and Function Reset
4-9
0- Drive Operation Mode
Function Factory
LCD Display Description Range/Code Remarks
Code No. Setting
0000: Vector (General Purpose)
0001: Vector (Variable Torque)
0-00 (Control Mode) Control Mode 0000 *3
0002: Volts/Hz (Refer to Parameter
Group 10- Volts/Hz Mode)
0-01 (Motor Rated Volt) Motor Rated Voltage (Vac) ----- *3*5
0-02 (Motor Rated Amp) Motor Rated Current (Amp) ----- *3*5
0-03 (Motor Rated KW) Motor Rated Power (kW) ----- *3*5
(Motor Rated RPM) Motor Rated Speed *3*5
0-04 -----
(RPM)X100*7
0-05 (Motor Rated Hz) Motor Rated Frequency (Hz) ----- *3*5
0000: Invalid
0-06 (Auto Tuning) Motor Parameter Auto Tuning 0000
0001: Valid
220V SERIES:170.0~264.0
0-07 (AC Input Volt) AC Line Input Voltage (Vac) *3
440V SERIES:323.0~528.0
0000: English
0001: German Only for
0-08 (Select Language) Language Selection 0002: French 0000 LCD
0003: Italian keypad
0004: Spanish
1- Start/Stop and Frequency Control Modes

Function Factory
LCD Display Description Range/Code Remarks
Code No. Setting
0000: Keypad
0001: External Run/Stop Control
1-00 (Run Source) Run Command Source Selection (See 1-01) 0000
0002: Communication
0003: Built-In PLC
0000: Forward/Stop-Reverse/Stop
Run/Stop-Forward/Reverse
0001: Run/Stop-Forward/Reverse
1-01 (MFIT Run Mode) Operation Mode with External 0000
0002: 3-Wire Control Mode-
Terminals
Run/Stop
0000: Enable Reverse Command
1-02 (Reverse Oper) Prohibition of Reverse operation 0000
0001: Disable Reverse Command
0000: Stop Button Enabled
1-03 (Keypad Stop) Keypad Stop Button 0000
0001: Stop Button Disabled
0000: Normal Start
1-04 (Starting Method) Starting Method Selection 0000
0001: Enable Speed Search
0000: Controlled Deceleration-to-
Stop with DC Injection
1-05 (Stopping Method) Stopping Method Selection
Braking (Rapid Stop)
0001: Free run Stop
4-10
0000: Keypad
0001: Potentiometer on Keypad
0002: External Analog Signal Input
or Remote Potentiometer
0003: Up/Down Frequency
Frequency Command Source
1-06 (Frequency Source) Control Using MFIT (S1 - 0000
Selection
S6)
0004: Communication setting
frequency
0005: Impulse (S5) setting
frequency (ver2.3)
0000: ‘Enter’ must be pressed after
frequency change with
Keypad Operation with Up/Down Up/Down Keys on keypad.
1-07 (Keypad Up/Down) 0000
Keys in Run Mode 0001: Frequency will be changed
directly when Up/Down
Keys are Pressed
2- Manual/Automatic Restart Modes

Function LCD Factory
Description Range/Code Remarks
Code No. Display Setting
0000: Momentary power loss and
restart disable
0001: Momentary power loss and
Momentary Power Loss and restart enable
2-00 (PwrL Selection) 0000
Restart 0002: Momentary power loss and
restart enable while CPU is
operating. (According to the
capacity of DC power)
Momentary Power Loss
2-01 (PwrL Ridethru T) 0.0 - 2.0 0.5
Ride-Thru Time (Seconds)
Auto Restart Delay Time
2-02 (Delay of Restart) 0.0 - 800.0 0.0
(Seconds)
Number of Auto Restart
2-03 (Num of Restart) 0 - 10 0
Attempts
2-04 (Auto Restart) Auto Restart Method 0000
0001: Normal Start
0000: Enable Direct running after
power up
2-05 (Direct Start Sel) Direct Running After Power Up 0000
0001: Disable Direct running after
power up
2-06 (Delay-on Timer) Delay-ON Timer (Seconds) 0.0-300.0 0.0
0000: Enable Reset Only when Run
Command is Off
2-07 (Reset Mode Sel) Reset Mode Setting 0000
0001: Enable Reset when Run
Command is On or Off
Kinetic Energy Back-up 0.0:Disable
2-08 (KEB_Decel_Time) 0.0
Deceleration Time 0.1~25.0: KEB Deceleration Time
4-11
3- Operating Parameters
50.00／
3-00 (Freq Upper Limit) Frequency Upper Limit (Hz) 0.01 - 650.00 *4
60.00
3-01 (Freq Lower Limit) Frequency Lower Limit (Hz) 0.00 - 650.00 0.00
Acceleration Time # 1
3-02 (Accel Time 1) 0.1 – 3600.0 10.0 *1
(Seconds)
Deceleration Time # 1
3-03 (Decel Time 1) 0.1 – 3600.0 10.0 *1
(Seconds)
3-04 (S-Curve 1) S-Curve Acc/Dec # 1 (Seconds) 0.0 - 4.0 0.2
3-05 (S-Curve 2) S-Curve Acc/Dec # 2(Seconds) 0.0 - 4.0 0.2
Acceleration Time # 2 (MFIT)
3-06 (Accel Time 2) 0.1 – 3600.0 10.0 *1
(Seconds)
Deceleration Time # 2 (MFIT)
3-07 (Decel Time 2) 0.1 – 3600.0 10.0 *1
(Seconds)
Jog Acceleration Time (MFIT)
3-08 (Jog Acc Time) 0.1 - 25.5 0.5 *1
(Seconds)
Jog Deceleration Time (MFIT)
3-09 (Jog Dec Time) 0.1 - 25.5 0.5 *1
(Seconds)
DC Injection Brake Start
3-10 (DCInj Start Freq) 0.1 - 10.0 1.5
Frequency (Hz)
3-11 (DCInj Level) DC Injection Brake Level (%) 0.0 – 20.0 5.0 *7
DC Injection Brake Time
3-12 (DCInj Time) 0.0 - 25.5 0.5
(Seconds)
3-13 (Skip Freq 1) Skip Frequency # 1 (Hz) 0.00 - 650.00 0.0 *1
Skip Frequency Bandwidth(±
3-16 (Skip Bandwidth) 0.00 - 30.00 0.0 *1
Hz)
0000: Enable all Functions
0001: 6-00 - 6-08 cannot be changed
3-17 (Parameter Lock) Parameter Lock 0002: All Functions Except 6-00 - 0000
6-08 cannot be changed
0003: Disable All Function
0000: Disable
0001: Inverter to Copy Unit
3-18 (ROM Pack Operate) Copy Unit 0000
0002: Copy Unit to Inverter
0003: Verify
0000: Auto (Depend on temp.)
0001: Operate while in RUN mode
3-19 (Fan Control) Fan Control 0000
0002: Always Run
0003: Always Stop
0000: Disabled
3-20 (Energy Save Mode) Energy Saving Mode *1 0001: Controlled by MFIT at Set 0000 *6
Frequency
3-21 (Energy Save Gain) Energy Saving Gain (%)*1 0 - 100 80 *6
3-22 (Carrier Freq) Carrier Frequency (kHz) 2 - 16 10
3-23 reserved
4-12
3-24 reserved
3-25 reserved
3-26 reserved
3-27 reserved
3-28 reserved
3-29 reserved
※ Notes: 1. Energy Saving Mode is available only under Volts/Hz Mode (0-00 = 0002).
4- Digital Display Operation Mode

0000: Disable Motor Current Display
4-00 (Motor Curr Disp) Motor Current Display Selection 0000 *1
0001: Enable Motor Current Display
0000: Disable Motor Voltage Display
4-01 (Motor Volt Disp) Motor Voltage Display Selection 0000 *1
0001: Enable Motor Voltage Display
DC Bus Voltage Display 0000: Disable Bus Voltage Display
4-02 (Bus Volt Disp) 0000 *1
Selection 0001: Enable Bus Voltage Display
0000: Disable PLC Status Display
4-03 (PLC Status Disp) PLC Status Display Selection 0000 *1
0001: Enable PLC Status Display
Custom Units (Line Speed)
4-04 (Display Scaling) 0 - 9999 1800 *1
Value
0000: Drive Output Frequency is
Displayed
0001: Line Speed is Displayed in
Integer (xxxx)
Custom Units (Line Speed) 0002: Line Speed is Displayed with
4-05 (Display Units) 0000 *1
Display Mode One Decimal Place (xxx.x)
0003: Line Speed is Displayed with
Two Decimal Places (xx.xx)
0004: Line Speed is Displayed with
Three Decimal Places (x.xxx)
0000: Disable PID Feedback Display
4-06 (PID Feed Disp) PID Feedback Display Selection 0000 *1
0001: Enable PID Feedback Display
5- Multifunction Input Terminals (MFIT)

4-13
0000: Forward/Stop Command *1
0001: Reverse/Stop Command *2
5-00 (MFIT S1 Sel) Multifunction Input Term. S1 0002: Preset Speed # 1 (6-02) 0000
0003: Preset Speed # 2 (6-03)
0004: Preset Speed # 3 (6-05) *3
0005: Jog
5-01 (MFIT S2 Sel) Multifunction Input Term. S2 0006: Acc/Dec # 2 0001
0007: Emergency Stop A Contact
0008: Base Block
0009: Speed Search
0010: Energy Saving
5-02 (MFIT S3 Sel) Multifunction Input Term. S3 0002
0011: Control Signal Selection
0012: Communication Selection
0013: Acc/Dec Disabled
0014: Up Command
5-03 (MFIT S4 Sel) Multifunction Input Term. S4 0015: Down Command 0003
0016: Master/Auxiliary Speed
0017: PID Function Disabled
0018: Reset
5-04 (MFIT S5 Sel) Multifunction Input Term. S5 0019: Encoder input terminal 0004
( terminal S5 )
0020: PID feedback signal A12
（terminal S6）
0021: AI2 Bias signal 1 input
5-05 (MFIT S6 Sel) Multifunction Input Term. S6 0018
（terminal S6）
0022: AI2 Bias signal 2 input
（terminal S6）
0023: Analog input（terminal AIN）
0024: PLC Application
0025: Traverse Run
5-06 (MFIT AIN Sel) Multifunction Input Term. AIN 0026: Traverse run upper deviation 0023
0027: traverse run lower deviation
0028: Power Source Detect for KEB
Function
0029: Emergency Stop B Contact *7
Multifunction Input Term. S1 -
5-07 (MFIT Scan Time) S6 Signal Verification Scan 1 – 100 5
Time (mSec X 4 )
4-14
0000: When the MFITs are
Programmed for Up/Down
Frequency Control, the Set
Frequency will remain when
the Drive stops. And when the
Drive stops, Up/Down
Function Disabled.
0001: Up/Down is used. The preset
5-08 (Stop Sel by MFIT) Stop Mode Using MFIT frequency is reset to 0 Hz as 0000
the inverter stops.
0002: When the MFITs are
Programmed for Up/Down
Frequency Control, the Set
Frequency will remain when
the Drive stops. And when the
Drive stops, Up/Down
Function Enabled. *7
5-09 (Step Up/Down Fun) Step of Up/Down Function (Hz) 0.00 – 5.00 0.00
5-10 (Pulse Inp. Mult.) Encoder Impulse Ratio 0.001 – 9.999 1.000 *7
Select the source of auxiliary
5-11 (Ref.Source2) 0-4 0 *7
frequency command
※Notes: 1. To switch to Run/Stop with Function 1-01 = 0001.
2. To switch to Forward/Reverse with Function 1-01 = 0001.
3. Preset Speed # 3 is obtained by activating Terms. S3 and S4 simultaneously.
6- Jog, and Preset (MFIT) Frequency Setting on Keypad
6-00 (Keypad Freq) Keypad Frequency (Hz) 0.00 - 650.00 5.00 *1
6-01 (Jog Freq) Jog Frequency (Hz) 0.00 - 650.00 2.00 *1
6-02 (Preset Speed #1) Preset Speed # 1 (Hz) 0.00 - 650.00 5.00 *1
7- Analog Input Signal Operation
7-00 (AIN Gain) AIN Gain (%) 0 - 200 100 *1
7-01 (AIN Offset) AIN Bias (%) 0 - 100 0 *1
0000: Positive
7-02 (AIN Bias) AIN Bias Selection 0000 *1
0001: Negative
0000: Positive
7-03 (AIN Slope) AIN Slope 0000 *1
0001: Negative
AIN Signal Verification Scan
7-04 (AIN Scan Time) Time (AIN, AI2) 1 - 100 50
(mSec x 2)
4-15
7-05 (AI2 Gain) AI2 Gain (%)(S6) 0 - 200 100 *1
※ Notes: Group 7 is available when 5-06=0023 (AIN term.=Analog input)
8- Multifunction Output Relays and Output Signal Operation
0000: Output Frequency
0001: Frequency Setting
Analog Output Voltage Mode 0002: Output Voltage
8-00 (AO Mode Sel) 0000 *1
(0 - 10 VDC, Term. FM+) 0003: DC Voltage
0004: Output Current
0005: PID Feedback *7
8-01 (AO Gain) Analog Output Gain (%) 0 - 200 100 *1
0000: Run
0001: Frequency Reached
(Frequency Command) (Set
Frequency ± 8-05)
0002: Set Frequency (8-04 ± 8-05)
Output Relay R1 Operation 0003: Frequency Threshold Level (>
8-02 (Relay R1 Sel) 0006
Mode 8-04) - Frequency Reached
0004: Frequency Threshold Level (<
8-04) - Frequency Reached
0005: Over torque Threshold Level
0006: Fault
0007: Auto Restart
0008: Momentary AC Power Loss
0009: Rapid Stop Mode
0010: Coast-to-Stop Mode
Output Relay R2 Operation 0011: Motor Overload Protection
8-03 (Relay R2 Sel) 0000
Mode 0012: Drive Overload Protection
0013: PID Feedback Signal Loss
0014: PLC Operation
0015: Power On *7
Frequency Reached (Hz)
8-04 (Freq Agree) 0.00 - 650.00 0.00 *1
(Refer to 8-02: 0001)
Frequency Reached Bandwidth
8-05 (Freq Agree width) 0.00 - 30.00 2.00 *1
(± Hz)
9- Drive and Load Protection Modes
0000: Enable Trip Prevention During
Trip Prevention Selection Acceleration
9-00 (Trip ACC Sel) 0000
During Acceleration 0001: Disable Trip Prevention
During Acceleration
Trip Prevention Level During
9-01 (Trip ACC Level) 50 - 300 200
Acceleration (%)
0000: Enable Trip Prevention During
Trip Prevention Selection Deceleration
9-02 (Trip DEC Sel) 0000
During Deceleration 0001: Disable Trip Prevention
During Deceleration
4-16
Trip Prevention Level During
9-03 (Trip DEC Level) 50 - 300 200
Deceleration (%)
0000: Enable Trip Prevention in Run
Trip Prevention Selection in Mode
9-04 (Trip RUN Sel) 0000
Run Mode 0001: Disable Trip Prevention in
Run Mode
Trip Prevention Level In Run
9-05 (Trip Run Level) 50 - 300 200
Mode (%)
0000: Trip Prevention Deceleration
Trip Prevention Deceleration Time Set by 3-03
9-06 (Dec Sel Trip RUN) 0000
Time Selection in Run Mode 0001: Trip Prevention Deceleration
Time Set by 9-07
(Dec Time Trip Deceleration Time In Trip
9-07 0.1 – 3600.0 3.0
RUN) Prevention Mode (Seconds)
0000: Enable Electronic Motor
Electronic Motor Overload Overload Protection
9-08 (Motor OL1 Sel) 0000
Protection Operation Mode 0001: Disable Electronic Motor
Overload Protection
0000: Electronic Motor Overload
Protection Set for
Non-Inverter Duty Motor
9-09 (Motor Type) Motor type Selection 0000
0001: Electronic Motor Overload
Protection Set for Inverter
Duty Motor
0000: Constant Torque (OL =103 %)
Motor Overload Protection (150 % for 1 Minute)
9-10 (Motor OL1 Curve) 0000
Curve Selection 0001: Variable Torque (OL = 113 %)
(123 % for 1 Minute)
0000: Coast-to-Stop After Overload
Protection is Activated
Operation After Overload
9-11 (Motor OL1 Operat) 0001: Drive Will Not Trip when 0000
Protection is Activated
Overload Protection is
Activated (OL1)
0000: Disable Over torque Operation
0001: Enable Over torque Operation
Only if at Set Frequency
9-12 (Torq Det Sel) Over torque Detection Selection 0000
0002: Enable Over torque Operation
while the Drive is in Run
Mode
0000: Drive will Continue to
Operate After Over torque is
Operation After Over torque
9-13 (Torq Det Operat) Activated 0000
Detection is Activated
0001: Coast-to-Stop After Over
torque is Activated
Over torque Threshold Level
9-14 (Torq Det Level) 30 - 200 160
(%)
Over torque Activation Delay
9-15 (Torq Det Delay) 0.0 - 25.0 0.1
Time (Seconds)
4-17
10- Volts/Hz Operation Mode

10-0 (V/F Selection) Volts/Hz Patterns 0 - 18 0/9 *4*6
Volts/Hz Curve Modification
10-1 (Torque Boost) 0 – 30.0 0.0 *1*6
(Torque Boost) (%)
Motor No Load Current
10-2 (Motor noLoad Amp) ----- *5*6
(Amps AC)
10-3 (Motor rated Slip) Motor Slip Compensation (%) 0.0 – 100.0 0.0 *1*6
50.00/
10-4 (Max frequency) Maximum Frequency (Hz) 0.20 - 650.00 *4*6
60.00
Maximum Frequency Voltage
10-5 (Max Voltage) 0.0 - 100.0 100.0 *6
Ratio (%)
25.00/
10-6 (Mid frequency) Mid Frequency (Hz) 0.10 - 650.00 *4*6
30.00*7
Mid Frequency Voltage Ratio
10-7 (Mid Voltage) 0.0 - 100.0 50.0*7 *6
(%)
10-8 (Min frequency) Minimum Frequency (Hz) 0.10 - 650.00 0.50/ 0.60 *6
Minimum Frequency Voltage
10-9 (Min Voltage) 0.0 - 100.0 1.0*7 *6
Ratio (%)
11- PID Operation Mode

0000: Disabled
0001: Bias D Control
0002: Feedback D Control
0003: Bias D Reversed
Characteristics Control
0004: Feedback D Reversed
0005: Frequency Command + Bias D
11-0 (PID Mode Sel) Mode Selection Control 0000
0006: Frequency Command +
Feedback D Control
0007: Frequency Command + Bias D
Reversed Characteristics
Control
0008: Frequency Command +
Feedback D Reversed
11-1 (Feedback Gain) Feedback Gain (%) 0.00 - 10.00 1.00 *1
11-2 (PID Gain) Proportional Gain (%) 0.0 - 10.0 1.0 *1
11-3 (PID I Time) Integration Time (Seconds) 0.0 - 100.0 10.0 *1
11-4 (PID D Time) Differentiation Time (Seconds) 0.00 - 10.00 0.00 *1
0000: Positive
11-5 (PID Offset) PID Offset 0000 *1
0001: Negative
11-6 (PID Offset Adj) PID Offset Adjust (%) 0 - 109 0 *1
4-18
Output Lag Filter Time
11-7 (Output Filter T) 0.0 - 2.5 0.0 *1
(Seconds)
12- PID "Limits" and "Out of Range" Mode
0000: Disabled
0001: Enabled - Drive Continues to
12-0 (Fb Los Det Sel) Feedback Loss Detection Mode Operate After Feedback Loss 0000
0002: Enabled - Drive "STOPS"
After Feedback Loss
Feedback Loss Detection Level
12-1 (Fb Los Det Lvl) 0 - 100 0
(%)
Feedback Loss Detection Delay
12-2 (Fb Los Det Time) 0.0 -25.5 1.0
Time (Seconds)
12-3 (PID I Limit) Integration Limit Value (%) 0 - 109 100 *1
Integration Value Resets to Zero 0000: Disabled
12-4 (I Time value Sel) when Feedback Signal Equals 0001: 1 Second 0000
the Intended Value 0030: 30 Seconds
Allowable Integration Error
12-5 (I Error Margin) Margin (Units) 0 - 100 0
(1 Unit = 1/8192)
0000: 0~10V or 0~20mA
12-6 (PID Comm. Source) PID Feedback signal 0000 *7
0001: 2~10V or 4~20mA
12-7 (Sleep Level) Sleep Function Operation Level 0.00-650.00 0.0
12-8 (Sleep Delay Time) Sleep Function Delay Time 0.0-25.5 0.0
13- Communication Mode

Assigned Communication
13-0 (Serial Comm Adr) 1 - 254 1 *2*3
Station Number
0000: 4800
0001: 9600
13-1 (Serial Baud Rate) Baud Rate Setting (bps) 0003 *2*3
0002: 19200
0003: 38400
0000: 1 Stop Bit
13-2 (Comm Stop Bit) Stop Bit Selection 0000 *2*3

0001: 2 Stop Bits
0000: Without Parity

13-3 (Comm Parity Sel) Parity Selection 0001: With Even Parity 0000 *2*3
0002: With Odd Parity
(Comm Data 0000: 8-Bits Data
13-4 Data Format Selection 0000 *2*3
Format) 0001: 7-Bits Data
4-19
14- Motor Auto-Tune Parameters

14-0 (Stator Resistor) Stator Resistance (Ohms) ----- *3*5
14-1 (Rotor Resistor) Rotor Resistance (Ohms) ----- *3*5
14-2 (Equi Inductance) Equivalent Inductance (mH) ----- *3*5
Magnetizing Current (Amps
14-3 (Magnet Current) ----- *3*5
AC)
14-4 (Ferrite Loss) Ferrite Loss Conductance (gm) ----- *3*5
15- Drive Status and Function Reset
15-0 (Drive Model) Drive Horsepower Code (See page 4-53) *3
15-1 (Software Version) Software Version ----- ----- *3
15-2 (Fault Log) Fault Jog (Last 3 Faults) (See page 4-53) ----- *3
Accumulated Operation Time
15-3 (Elapsed Hours) 0 - 9999 ----- *3
(Hours)
Accumulated Operation Time
15-4 (Elapsed Hr*10000) 0 - 27 ----- *3
(Hours X 10000)
Accumulated Operation Time 0000: Time Under Power
15-5 (Elapsed Time Sel) 0000 *3
Mode 0001: Run Mode Time Only
1110:Reset for 50 Hz Motor
Operation
15-6 (Reset Parameter) Reset Drive to Factory Settings 1111: Reset for 60 Hz Motor 0000 *4
Operation
1112: Reset PLC Program
※Notes: *1 can be modified during operation
*2 cannot be modified during communication

*3 do not change while making factory setting
*4 as parameter related to factory setting
*5 the parameter will be changed by replacing model (see descriptions of the
POSTSCRIPT 1)
*6 only available in V/F mode
*7 only for version 2.3 and above.
4-20
4.4 Parameter Function Description
Parameter Group 0: Drive Operation Mode
0-00：Control Mode
0000：Vector mode (General Mode)
0001：Vector mode (VT Mode)
0002：V/F mode
To select the most suitable vector control mode or V/F mode according to the load characteristics.
1. Vector (general mode) is inclined to control the general load or rapidly-changed torque load.
2. Vector (VT mode) is suitable for Blower/ Pump and HVAC load. The magnetic current of
motor will be variable with the torque, which will reduce the current to save the energy.
3. As V/F mode is selected, please set the parameter group10 comply with the load features.
0-01:Motor Rated Voltage（Vac）
0-02:Motor Rated Current（A）
0-03:Motor Rated Power (kW)
0-04:Motor Rated Speed (RPM)
0-05:Motor Rated Frequency (Hz)
0-06:Motor Parameter Auto Tuning
0000: Disabled 0001: Enabled
It is necessary to input the data on nameplate and auto tuning as long as changing the motor as
vector mode is selected.
Auto tuning: firstly input the data to 0-01~0-05 according to the nameplate after power off, then set
0-06=0001and perform auto tuning; the motor will run. It will stop as the inverter finishes auto
tuning. The detected internal data will auto be written to parameter group 14.
ex. If the motor rated speed is 1700 rpm, please set 0-04 to 17.0
Precaution
1. The motor parameter auto tuning is the stationary auto tuning. During motor auto tuning, the motor
does not rotate, and the keypad display -AT-.
2. During motor parameter auto tuning, the input signal in control circuit is invalid.
3. Before motor parameter auto tuning, please confirm the stop state of the motor.
4. The motor parameter auto tuning is only available for vector control mode (0-00=0000or 0-00=0001).
0-07 AC Line Input Voltage (Volts AC)
220V series：170.0~264.0
440V series：323.0~528.0
To make sure the voltage level of inverter, please input the actual on-site voltage value.
0-08 Language Selection
0000: English
0001: German
0002: French
0003: Italian
0004: Spanish
4-21
The function is only available for the products with LCD operation keypad. The operation is not
necessary for the one with LED.
4-22
Parameter Group 1 - Start/Stop and Frequency Control Modes

1-00 : Run Command Source Selection
0000:Keypad
0001:External terminal control
0002:Communication control
0003:Built-in PLC
1.) 1-00=0000 the inverter is controlled by the keypad.
2.) 1-00=0001 the inverter is controlled by the external terminals, and the Stop key for emergency
does work. (Refer to 1-03 description).
Note: 1-00=0001, please refer to parameter group 2-00, 2-01, 2-02 and 2-03 for detail description
to make secure of persons and machines.
3.) 1-00=0002 the inverter is communication controlled.
4.) 1-00=0003 the inverter is built-in PLC controlled, and 1-06 preset value is invalid.
1-01 : Operation modes for external terminals

0000:Forward/stop-reverse/stop
0001:Run/stop-forward/reverse
0002:3-wire control mode -run/stop
1.) When operation command 1-00 = 0001 (external terminal), 1-01 is valid.
2.) When operation command 1-00 = 0001 (external terminal control), the stop button for emergency
is available. (Refer to 1-03 for detail description).
3.) That both forward and reverse commands are ON will be treated as STOP.
1-01 = 0000, Control mode is as below:

(2). Input signal is PNP:
(1).Input signal is NPN:
S1 (forward) S1 (forward)
S2 (reverse) S2 (reverse)
COM (0V common) 24V (common)
轉

(2). Input signal is PNP:
(1). Input signal is NPN:
S1 (run)
S1 (run)
S2 (forward/reverse)
S2
COM (0Vcommon)
(forward/reverse)
4-23
(1). Input signal is NPN: (2). Input signal is PNP:
S1 (run) S1 (run)
S2 (stop) S2 (stop)
S3 (FWD/REV) S3 (FWD/REV)
COM 24V(common)
※Note: As 3 wire control mode is selected, the terminal S3 is not controlled by 5-02.
※Note: 1-02=0001, the reverse command is unavailable.
1-02 : Prohibition of Reverse Operation 0000: Enable Reverse Command

0001: Disable Reverse Command
1-02=0001, the reverse command is invalid.
1-03 : Keypad Stop Button 0000: Stop Button Enable
0001: Stop Button Disable
1-03=0000，The STOP key is available for controlling the inverter to stop.
1-04 : Starting Method Selection 0000: Normal Start
1.) 1-04=0000：As starting, the inverter accelerates from 0 to target frequency in the set time.
2.) 1-04=0001：As starting, the inverter accelerates to target frequency from the detected speed of
motor.
1-05 : Stopping Method 0000: Controlled Deceleration-to- Stop with DC Injection Braking
4-24
(Rapid Stop)
0001: Free run stop
1.) 1-05=0000: the inverter will decelerate to 0Hz in preset deceleration time after receiving the stop
command.
2.) 1-05=0001: the inverter will stop output as receiving the stop command. The motor will inertia
free run to stop.
1-06 : Frequency Command Source Selection
0000: Set the Frequency with Keypad
0001: Potentiometer on Keypad
0002: External Analog Signal Input or Remote Potentiometer
0003: Up/Down Frequency Control Using MFIT (S1 - S6)
0004: Communication Setting Frequency
0005: Impulse frequency (S5) setting frequency (ver2.3)
1.) 1-06=0001，as one of the parameter in group 5-00~ 5-06is set 16 and multifunction terminal is
OFF, the frequency is set by the KNOB(VR for principal speed) on keypad. While the
multifunction is ON, the frequency is set by analog signal (auxiliary speed) on terminal block
(TM2).
2.) 1-06=0002，as one of the parameter in group 5-00~ 5-06 is set 16 and the multifunction terminal
is OFF, he frequency is set by analog signal (principal speed) on terminal block (TM2), While
the multifunction is ON, the frequency is set by the KNOB(VR for auxiliary speed) on keypad.
3.) Please refer to description of parameter group 5-00~ 5-06 (multifunction input terminals) for the
function Up/Down terminal.
4.) The priority in reading frequency is PLC frequency control >traverse run >Jog> preset
speed>▲▼ on keypad or Up / Down or communication control.
5.) Impulse frequency command input source should be setting as S5 terminal and need to
coordinate with 5-10 frequency exchange times ratio. For example, the input value S5 is 4KHZ,
5-10 is 1.500 times, and output frequency is 40.00*1.5=60.00HZ. 5-04(S5) should be setting as
19.
1-07:Keypad Operation with Up/Down Keys in Run Mode
0000: ‘Enter’ must be pressed after frequency change with Up/Down Keys on keypad.
0001: Frequency will be changed directly when Up/Down Keys are Pressed
4-25
Parameter Group 2 - Manual/Automatic Restart Modes

2-00: Momentary Power Loss and Restart
0000: Momentary Power Loss and Restart Disable
0001: Momentary Power Loss and Restart is Enable
0002: Momentary Power Loss and Restart Enable while CPU is Operating.
2-01 : Momentary Power Loss Ride-Thru Time(sec): 0.0 - 2.0 second
1.) As start of the other load of power supply results in lowering the voltage below the under voltage
level, the inverter will stop output at once. If the power supply recovers in the 2-01 preset time, it
will spin start tracing from the trip frequency, or the inverter will trip with ‘LV-C’ displayed.
2.) The allowable power loss time differs with the models. The range is from 1second to 2 second.
3.) 2-00=0000: as power lost, the inverter will not start.
4.) 2-00=0001: if the loss time is less than the value of 2-01, the inverter will Spin Start in 0.5
second as the power supplied and restart times are infinite.
5.) 2-00=0002: the power lost for long time, before the inverter lost the control power for the CPU,
the inverter will restart according to the 1-00 and 2-04 setting and status of external switch as the
power resupplied.
※Note: 1-00=0001, 2-04=0000, 2-00=0001or 0002 after power lost for a long time, please OFF the
power and power switches in case of injury to person and machine by the resupplied power.
2-02：Auto restart Delay Time :0 ~ 800.0 second
2-03：Number of Auto restart Attempts :0 ~ 10 times
1.) 2-03=0：the inverter will not auto restart as trip for accident.
2.) 2-03>0，2-02= 0:
The inverter will conduct SPIN START in 0.5 second after trip for accident. The motor will
inertia run to frequency at the trip stop, then according to setting accelerate or decelerate time to
target frequency.
3.) 2-03>0，2-02>0：
The output will be stopped for a period which is determined by the 2-02 after accident trip. Then,
spin start to present target frequency.
4.) As the inverter is set in braking deceleration or DC braking, it will not perform restart after accident.
2-04 : Start Method:

0001: Normal Start
1.) 2-04=0000：the inverter will detect motor speed and accelerated the setting frequency as speed
4-26
search enable.
2.) 2-04=0001：the inverter will accelerated the motor speed from stop (zero speed) to setting
frequency.
2-05 :Direct running after power up:
0000: Enable Direct Running After Power Up
0001: Disable Direct Running After Power Up
Danger：
1.) 2-05=0000 and the inverter is set external terminal controlled（1-00=0001）, if the run switch is
ON as power is supplied, the inverter will auto start. It is recommend that to cut off the power
switch and run switch in case of injury to persons or machine as power is supplied again.
2.) 2-05=0001and the inverter is set external terminal controlled（1-00=0001）, if the run switch is
ON as power is supplied, the inverter will not auto start and flash STP1. It is necessary to
OFF the run switch and then ON to normally start.
2-06 : Delay-ON Timer (seconds): 0 ~ 300.0 second

As power on and 2-05=0000, the inverter will perform auto restart in the setting time for delay.
2-07: Error reset mode setting 0000: Enable Reset Only when Run Command is Off
0001: Enable Reset when Run Command is On or Off
2-07=0000as the inverter is detected the accident, please cut off the Run switch to perform reset, or
restarting does not work.
2-08: Kinetic Energy Back-up Deceleration Time:0.00~25.00 second
2-08 = 0 KEB function disable
2-08≠0 KEB function enable
Ex: 220V system
4-27
※NOTE:
1.When 2-08≠0，the momentary power loss and Restart is disabled,the inverter will do KEB
Function.
2.When power off，CPU detect the DC Voltage. KEB function enable when DC Voltage below than
190V（220V system）or 380V（440V system）.
3.When KEB function enabled,the inverter decelerate to zero by 2-08,and the inverter stop.
4.IF the power on signal enabled during the KEB function ,the inverter accelerate to original
frequency.
Parameter Group 3 - Operating Parameters

3-00: Frequency Upper limit(Hz) : 0.01 - 650.00
3-01: Frequency Lower limit(Hz) : 0.01 - 650.00
Internal frequency
3-00 (upper frequency limit)
3-01 (lower frequency limit)

(note)
※Note: When 3-01 = 0 Hz and frequency command is 0 Hz，the inverter will stop at 0 speed.
When 3-01 > 0 Hz and frequency command ≦3-01，the inverter will output 3-01 preset
value.
3-02 : Acceleration Time #1 （second）: 0.1 – 3600.0

4-28
3-03 : Deceleration Time #1 （second）: 0.1 – 3600.0

3-04 : S Curve of First Acceleration Stage（second）: 0.0 – 4.0
3-05 : S Curve of Second Acceleration Stage（second）: 0.0 – 4.0
3-06 : Acceleration Time #2 （second）: 0.1 – 3600.0
3-07 : Deceleration Time #2 （second）: 0.1 – 3600.0
3-08 : Jog Acceleration Time（second）: 0.1 –25.5
3-09 : Jog Deceleration Time（second）: 0.1 – 25.5
1.) Formula for calculating acceleration and deceleration time: The denominator is base on the
rated frequency of motor.
Preset frequency Preset frequency
Acceleration time = 3-02 (or 3-06) x ，Deceleration time = 3-03 (or 3-07) x
0-05 0-05
2.)When 5-00 – 5-06 is set 06 (the second acceleration and deceleration time)，the first
acceleration/ deceleration/ S curve or the second acceleration/ deceleration/ S curve will be set
by ON the external input terminal.
3.) When 5-00 – 5-06 is set 05 (Jog)，Jog run is controlled by external terminals. The acceleration
and deceleration action will be at Jog acceleration and deceleration time.

4.)When 5-00 – 5-06 is set as 05(Jog) and 06(acceleration and deceleration time toggle), to
change the acceleration and deceleration time by ON the external terminals, and the list
setting:
Function Acc/ Dec time 1(3-02/3-03) Acc/ Dec time 2 (3-06/3-07) JOG Acc/Dec time (3-08/3-09)
1-06 determines the output 1-06 determines the output
preset value Run at 6-01Jog frequency
frequency frequency
5-00~5-05=05 Jog command Off Off On
5-00~5-05=04
Off On Off
Toggle Acc/Dec time.
5.)When S curve time (3-04/3-05) is set as 0, the S curve is useless. Namely, acceleration and deceleration
is at line.
6.)When S curve time (3-04/3-05) is larger than 0, the acceleration and deceleration action is as following
diagram.
7.)Regardless of the stall prevention period, actual acceleration and deceleration time =preset acceleration
/ deceleration time + S curve time. For example: acceleration time = 3-03+ 3-04。
4-29
8.)During acceleration and deceleration process, there might be residual error in acceleration and
deceleration toggling. Please set the S curve time as 0 (3-04/3-05), if you need to toggle acceleration
and deceleration time in acceleration / deceleration process.
SC ti
Output frequency
Time
3-10 : DC Injection Brake Start Frequency (Hz) : 0.1 – 10.0
3-11 : DC Injection Brake Level (%) : 0.0 – 20.0
3-12 : DC Injection Brake Time(second) : 0.0 – 25.5
3-12 / 3-10 is the action time and start frequency of DC braking, as graph below:
HZ
3-10
t
3-12
The upper setting of 3-11 will be corrected 20.0 after manual V2.3.
3-13 : Skip Frequency #1 (Hz) : 0.00 –650.00
3-16 : Skip Frequency Bandwidth (± Hz) : 0.00 –30.00
Example: as 3-13is set as 10.0Hz / 3-14 as 20.0 Hz / 3-15a s 30.0 Hz / 3-16 as 2.0Hz
10Hz ±2Hz=8-12Hz
20Hz ±2Hz=18-22Hz skip frequency
30Hz ±2Hz=28-32Hz
3-16
3-15
3-14
3-13
3-17: Parameter lock function

0000: Enable all Functions
0001: 6-00 - 6-08 cannot be changed
0002: All Functions Except 6-00 - 6-08 cannot be changed
0003: Disable All Function
4-30
3-18: Copy Unit

0000: Disable
0001: Inverter to Copy Unit
0002: Copy Unit to Inverter
0003: Verify
1.) 3-18=0000：Inverter can not copy parameter.
2.) 3-18=0001：Copy the inverter parameters to module.
3.) 3-18=0002：Copy the module parameters to inverter.
4.) 3-18=0003：Copy the parameters to inverter or module to mutually verify the parameters.
※Note: The copy function is available for the models with same capacity.
3-19: Fan Running Controlling

0000: Auto (Depend on temp.)
0001: Operate while in RUN Mode
0002: Always Run
0003: Always Stop
1.) 3-19=0000：The fan run as the inverter senses temperature rises. Thusly, extend the service
period.
2.) 3-19=0001：The fan runs while the inverter is running.
3.) 3-19=0002：The fan is continuously running regardless of the action of the inverter.
4.) 3-19=0003：The fan is always stopping regardless of the action of the inverter.
※Note: Depend on the hardware, the function is disable at 15HP above of 220V class and 20HP
above of 440V class. The fan is running after the inverter power on.
3-20: Energy Saving Mode Operation 0000: Disabled
0001: Controlled by MFIT at Set Frequency
3-21: Energy saving operation gain (%): 0-100
1.) In terms of FAN, PUMP or other heavy inertia loads which need greater start torsion, while in
operation they need not so high torsion. Consequently, to decline the output voltage to saving
energy by setting 3-20 is necessary.
2.) 5-00 ~5-06(Multifunction input terminal) set as10 to saving energy.
4-31
3.) 3-20=0001, If the multifunction terminal is set as 10（energy saving control terminal），the output
voltage will gradually decline to ‘original voltage’×‘3-21’ preset value as the terminal’ is ON.
The output voltage will rise to original voltage as the terminal is OFF.
※Note：1.The declining and rising speeds of voltage for energy saving is same as the ones for
SPEED SEARCH.
2. Energy saving mode is only available under V/F mode. (0-00 = 0002)。
3-22：Carrier Frequency (KHz) ： 2-16
Carrier Carrier Carrier Carrier

3-22 3-22 3-22 3-22
Frequency Frequency Frequency Frequency
2 2KHz 6 6KHz 10 10KHz 14 14KHz
3 3KHz 7 7KHz 11 11KHz 15 15KHz
4 4KHz 8 8KHz 12 12KHz 16 16KHz
5 5KHz 9 9KHz 13 13KHz
※ Note：The external electronic components maybe interfered, more serious, even the
motor vibration due to cutting of the high carrier frequency waveform, although the
inverter provides low noise environment in running. Thusly, it is necessary to regulate
the carrier frequency.
4-32
Parameter Group 4 - Digital Display Operation Mode
4-00：Motor Current Display Selection： 0000: Disable Motor Current Display
0001: Enable Motor Current Display
4-01：Motor Voltage Display Selection： 0000: Disable Motor Voltage Display
0001: Enable Motor Voltage Display
4-02：DC Bus Voltage Display Selection： 0000: Disable Bus Voltage Display
0001: Enable Bus Voltage Display
4-03：PLC Status Display Selection： 0000:Disable PLC Status Display
0001:Enable PLC Status Display

The function is available for LCD operation keypad, but not for LED one.
4-04：Custom Units (Line Speed) Value ： 0-9999

The max preset line value of 4-04 is equal to the rated frequency (0-05) of the motor. For
instance, given line speed 1800 is equal to display 900 when output is 30Hz while the operation
frequency is 60Hz.
4-05 : Custom Units (Line Speed) Display Mode

0000:Drive Output Frequency is Displayed
0001:Line Speed is Displayed in Integer (xxxx)
0002:Line Speed is Displayed with One Decimal Place (xxx.x)
0003:Line Speed is Displayed with Two Decimal Places (xx.xx)
0004:Line Speed is Displayed with Three Decimal Places (x.xxx)
The preset frequency is displayed as the inverter stops while the operation line speed is displayed as
the inverter is running.
4-06：PID Feedback Display 0000:Disabled
0001:Enable
Keypad displays PID feedback value :
Parameter 5-05=20 (That is, S6 is set as the PID feedback analog terminal, refer to PID),
11-0=1(PID is enabled), and 4-06=1(Display S6 as PID analog feedback value 0~100, the formula as
follow:)
4-33
If feedback signal is 0~10V, (12-6=0000), keypad display value = (S6/10V)*100
If feedback Signal is 4~20mA, (12-6=0001), keypad display value = (S6/20mA)*100
※Note: Please press DSP Key to switch between the output frequency and PID feedback value.
※Note: The inverter displays XXXF as Running, while XXXr as Stop.
4-34
Parameter Group 5-Multifunction Input Terminals (MFIT)

Multifunction input terminals (TM2 S1-S6/AIN) controlling：
5-00~06 0000: Forward/Stop Command *1
0001: Reverse/Stop Command *2
0002: Preset Speed # 1 (6-02)
0003: Preset Speed # 2 (6-03)
0004: Preset Speed # 3 (6-05) *3
0005: Jog
0006: Acc/Dec time # 2
0007: Emergency Stop Contact A
0008: Base Block
0009: Speed Search Stop
0010: Energy Saving
0011: Control Signal Selection
0012: Communication Control Signal Selection
0013: Acc/Dec Disabled
0014: Up Command
0015: Down Command
0016: Principal/Auxiliary Speed
0017: PID Function Disabled
0018: Reset
0019: Encoder Input Terminal（Terminal S5）
0020: PID Feedback Signal A12 （Terminal S6）
0021: AI2 Bias Signal 1 Input（Terminal S6）
0022: AI2 Bias Signal 2 Input（Terminal S6）
0023: Analog Input（Terminal AIN）
0024: PLC Application
0025: Traverse Run
0026: Traverse Run Upper Deviation
0027: Traverse Run Lower Deviation
0028: Power Source Detect for KEB Function
0029: Emergency Stop Contact B
A. The terminals S1-AIN on terminal block (TM2) are multifunction input terminals. The above 30
functions can be set in these terminals.
B. Function Description for 5-00~06:
1. 5-00~06=0/1(Forward/Reverse/Stop)
As forward command is ON, the inverter runs while stops as OFF. The 5-00 factory set is
forward.
As reverse command is ON, the inverter runs while stops as OFF. The 5-01factory set is
reverse.
2. 5-00~06=2-4(Preset speed 1~3)

External multifunction input terminals are ON, the inverter is operation at the preset time, and
the duration is determined by the time of the terminal ON. The corresponding frequency
parameter is illustrated below:
4-35
3. 5-00~06=5(Jog)
To select Jog operation as ON the external input terminals. Now, the inverter operates at the
Jog acceleration and deceleration time. The corresponding frequency parameter is illustrated
below:
The priority order of frequency: Jog Speed→Preset Speed→Keypad frequency or external frequency
signal
Multifunction Multifunction Multifunction terminal 1 Jog Command Output frequency
terminal3 terminal 2 Preset value =02 terminal preset value
Preset value=04 Preset value =03 Preset value =05
0 0 0 0 6-00
X X X 1 6-01
0 0 1 0 6-02
0 1 0 0 6-03
0 1 1 0 6-04
1 0 0 0 6-05
1 0 1 0 6-06
1 1 0 0 6-07
1 1 1 0 6-08
4. 5-00~06=6 (toggle acceleration and deceleration time)
On the external input terminal, to select the acceleration 1/ deceleration 1/ S curve 1 or
acceleration 2/ deceleration 2/ S curve 2.
5. 5-00~06=7 /29：External Emergency Stop Contact A or B.
The inverter will decelerate to stop and Flash E.S as the emergency stop signal received
regardless of 1-05 setting. After such signal released, OFF the operation switch then ON or Press
Operation Key, the inverter will restart from the start frequency. If the emergency signal was
released before the inverter stop completely, the inverter still carries out emergency stop. The
8-02/03 determines the action of the error terminal. As 8-02/0=0: the error terminal does not act
when the external emergency signal input. While 8-02/03=9, the error terminal does act when
emergency signal input.
6. 5-00~06=8：Base Block
The inverter stop output as receiving STOP command, and the motor Free-Run stops.
7. 5-00~06=9：Speed Search Stop
When starting, the inverter detects the present speed of the motor firstly, then, the inverter
accelerates from the present speed to preset speed.
8. 5-00~06=10：Energy-saving operation
In terms of FAN, PUMP or other heavy inertia loads which need greater start torque, while in
operation they need not so high torsion. Thusly, to decline the output voltage is to saving energy.
The output voltage gradually declines as the multifunction terminal is ON. It will gradually
increase (to the original voltage) as the Multifunction terminal is OFF.
※Note：The acceleration and deceleration speed of energy saving operation is the same as the speed of
SPEED SEARCH.
4-36
9. 5-00~06=11： Switch of the control signal
External switch terminal is OFF：1-00/01 determines the operation signal and frequency signal.
External switch terminal is ON：Keypad controls the operation signal and frequency signal but not
controlled by 1-00/01.
10. 5-00~06=12： Switch of the inverter controlling in communication
External switch terminal is OFF：in communication, the master (PC or PLC) can control the
inverter operation and frequency signal and allowably modify the parameters, and the operation
signals from Keypad and TM2 are idle. Furthermore, the keypad can only display the voltage,
current and frequency, the parameters are readable and not writable, and Emergency Stop is
valid.
External switch terminal is ON：in communication, the inverter is controlled by the keypad
regardless of the setting of 1-00/1-06 and master. Under such circumstance, the master still can
read and write the inverter parameters.
11. 5-00~06=13：Disable acceleration and deceleration
The acceleration and deceleration action is unavailable till the forbid acceleration and
deceleration signals are released. The action is illustrated in the graph below:
Operation
Signal
Disable
ACC/DEC
※Note： Operation Switch is OFF,

the command of disable
Output
Frequency
12. 5-00~06=14,15：UP / DOWN Function (Actual ACC/DEC time is base on the setting)：
(1)Please set 1-06 = 3 if you want to use the UP/DOWN Function, and the other frequency signals
are useless.
(2)Set 5-08 = 0 and 5-09 = 0, the inverter accelerates to the preset value of 6-00 when the
operation terminal is ON. Then, it maintains the certain speed. As the inverter receives the
UP/DOWN command, it will accelerate / decelerate till the command is released. The
inverter runs at the certain speed. The inverter will ramp stop or Free-Fun stop which is
determined by the 1-05 as long as the inverter receives the STOP command. And the
frequency of Stopping will be stored in 6-00. The UP/DOWN KEY is invalid as the inverter
stops. It is necessary to use the Keypad to modify the preset parameter.
4-37
(3)Set 5-08 = 1, the inverter will operate from 0Hz when the operation terminal is ON. The
action of UP/DOWN is as above description. The inverter will ramp stop or free-run stop
which determined by1-05 setting when as it receiving the Stop Command and back to 0Hz.
The next operation will start at 0 Hz.
(4) That UP/Down Signal Simultaneously act are invalid
(5) 5-09≠ 0, the inverter will accelerate to the setting of 6-00 and maintain at the speed. When
the UP/Down terminal is On, setting frequency is present value 6-00±5-09, and the inverter
will accelerate/ decelerate to frequency 6-00. The upper frequency limit and lower frequency
limit also restrict the operation. If the signal of UP/ DOWN is maintained over 2 seconds, the
inverter will begin to accelerate/ decelerate. If 5-09=0, the operation is the same, till the UP/
DOWN signal stops. Please refer to the time diagram of 5-09.
Operation
UP
DOWN
Output 6-00
Frequency
13. 5-00~06=16 Principal/Auxiliary speed toggle
Multifunction terminal = OFF, the frequency is set by the VR (Master Speed) on the
Keypad. Whereas, Multifunction terminal = ON, the frequency is set by the analog signal
terminal (Auxiliary Speed) on the TM2 on terminal Block.
14. 5-00~06=17(PID Function Disable)
The PID Function Disable is ON. PID is not controlled by 11-0, while OFF, it is controlled
by 11-0.
15. 5-00~06=18(Reset Command)
The Reset command is same as Reset Key on the panel is ON. The command is OFF, and the
inverter does not response. The factory set of 5-05 is Reset command.
16. 5-04=19 (Encoder Input terminal)
The multifunction terminal S5 is set 19 means it is the input terminal for PLC program
Encoder.
17. 5-05=20 (PID feedback input terminal)
The multifunction terminal S6=20 means the PID feedback input terminal and 0~10V (0~
20 mA) or 2~10V (4~20mA) is available by the setting of 11-0.
18. 5-05=21 /22(Bias signal 1/2 input)
To regulate the Offset of the Keypad VR or AIN analog input, only the signal of 0~10V (0~ 20 mA)
or 2~10V (4~20mA) is available.
5-05=21 Function 5-05=22Function * The value is 0 when AIN+(S6-5V)＜0
Hz Hz
4-38 Upper Frequency
Upper Frequency Limit 3-00
Limit 3-00
V V
0 10 0 5
19. 5-06=23 (Analog input AIN)

The multifunction terminal AIN = 23. The action is provided for setting the frequency.
20. 5-00~06=24 (PLC Application)
The multifunction terminal S1-AIN=24, which means the terminal is for PLC application.
The terminal is provided for the PLC program input.
21. 5-00~06=25 (Traverse Run); 5-00~06=26(Upper Deviation Traverse); 5-00~06=27(Lower
deviation Traverse).
The motion description refers to 3-23~3-29 for detail description.
22. 5-00~06=28 (Power Source Detect for KEB Function)
Please refer to the description of 2-08
Digital /Analog input signal scan times:

5-07: Multifunction terminal S1～S6 and AIN signal confirm the scan times (mSec X 4)，1~100
times
1.TM2 terminal used as scanning, if there are same signals continuously input for N times(Namely, Scan
times), the inverter will treated the signal as normal. During performing the signal, if the scan times
are less than N, the signal will be as noise.
2. Each scan period is 4ms.
3. The user can specify the scan times interval duration according to the noise environment. If the
noise is serious, upper modify the value of 5-07, but the response speed will be slow down.
4. Note: If the S6 and AIN is for digital signal, the voltage level for digital signal above 8V is treated
as ON, below 2V is OFF.
Stop Mode Using MFIT:

5-08:
0000: When Up/Down is used, the preset frequency is hold as the inverter stops, and the UP/Down is
idle.
0001: When Up/Down is used, the preset frequency is reset to 0 Hz as the inverter stops.
0002: When Up/Down is used, the preset frequency is hold as the inverter stops, and the UP/Down is
available.
(1) Set 5-08=0, the inverter will accelerate to the speed of 6-00 as receiving the Run command and
run at such certain speed. The inverter begins to accelerate (decelerate) as the UP (Down) terminal
is energized. The inverter will hold the speed as the UP/DOWN command released. When the Run
Signal releases, the inverter will ramp stop or stop output (determined by the 1-05). It will store the
frequency when the operation signal disappeared. UP/DOWN keys are idle when the inverter is
stop. The keypad is available for you modify the preset frequency (6-00). If 5-08=0002, the
UP/Down is available as the inverter stops.
4-39
(2)Set 5-08=1, as the Run terminal is energized, the inverter operates from 0 Hz, the Function of
UP/DOWN is same as the above description. When the Run Signal released, the inverter will
ramp stop or stop output (determined by 1-05) .And back to 0 Hz. The following operation will
always begin from 0 Hz.
Step of Up/Down Function (Hz):
5-09：Up/Down (Hz) 0.00 – 5.00
There are two modes covered below:

(1) 5-09 = 0.00, the function is disable. The operation is just as the original one. As UP terminal is
ON, the frequency increases while the DOWN terminal is ON, the frequency decreases. (Refer to
the following graph).
(2) 5-09 = 0.01 to 5.00, UP/ DOWN terminal ON, that equivalent to increase/ decrease the
frequency of 5-09. If the pressing is over 2second, revive the original UP/DOWN mode (Please
refer to the following diagram)
Encoder Impulse Ratio：
5-10 Impulse input frequency time ratio

When frequency source 1-06 be setting as 0005, the impulse signal frequency will be
according to this parameter to decide to the real inside frequency of inverter.
The inside calculate formula : Frequency = S5(impulse frequency)*5-10(times ratio)
For example, when S5 impulse is 1KZ（1000）, and 5-10 be setting as 1.50 times. The inverter
4-40
frequency command is 1000*1.5=1500=15.00HZ. The frequency accuracy of S5 is by base
of 100, 1K(1000) present 10.00 HZ.
Reference Source 2：
5-11 Auxiliary frequency source can be selected

Ex.
When frequency source command setting as impulse command, (1-06= 5)
If master speed operating (5-00~5-06 setting to 16 and the terminal is OFF), frequency
running as impulse frequency.
If auxiliary speed operating (5-00~5-06 setting to 16 and the terminal is ON), frequency
should be decided by 5-11 setting.
The action process as below:
5-11= 0, frequency refer to 6-00.
5-11= 1, frequency refer to the VR analog signal on the Keypad.
5-11= 2, frequency refer to the VR analog signal on TM2.
5-11= 3, frequency refer to the frequency value which is calculated by Up/Down on TM2.
5-11= 4, frequency refer to the input communication frequency.
4-41
Parameter Group 6- Jog and Preset (MFIT) Speed Setting on Keypad
Jog and Preset (MFIT) Speed Setting on Keypad：
6-00~08: Set Jog and preset speed by Keypad

A. 5-00~06=2-4(preset speed 1~3)
The external multifunction terminal = ON, the inverter operates at preset speed. The operation
time of the 8 stages is base on the ON time of the terminal. Please refer to the corresponding
parameters list:
B. 5-00~06=5(Jog terminal)
The external multifunction terminal = ON, the inverter operates in Jog acceleration time/ Jog
decelerate time/ON
Function LCD
Description Range/Code
Code No. Display
6-00 (Keypad Freq) Keypad Frequency (Hz) 0.00 - 650.00
6-01 (Jog Freq) Jog Frequency (Hz) 0.00 - 650.00
6-02 (Preset Speed #1) Preset Speed # 1 (Hz) 0.00 - 650.00
Priority in reading the frequency: Jog > Preset speed > Keypad frequency or external frequency signal
Multifunction Multifunction Multifunction Jog Command Output
terminal3 terminal 2 terminal 1 terminal frequency preset
Preset value=04 Preset value =03 Preset value =02 Preset value =05 value
0 0 0 0 6-00
X X X 1 6-01
0 0 1 0 6-02
0 1 0 0 6-03
0 1 1 0 6-04
1 0 0 0 6-05
1 0 1 0 6-06
1 1 0 0 6-07
1 1 1 0 6-08
4-42
Parameter Group 7 - Analog input signal operation mode

Analog Input Signal Operation Mode:
7-00:AIN Gain(%) 0 - 200
7-01:AIN Bias(%) 0 - 100
7-02:AIN Bias Selection: 0000:positive 0001:Negative
7-03:AIN Slope: 0000:positive 0001:Negative
7-04: AIN signal verification Scan Time (AIN, AI2) 1–100 (× 4mSec)
7-05: AI2 Gain (%)(S6) 0 - 200
1. 7-02 = 0：0V(0mA) corresponding to Lower Frequency Limit.，10V (20mA) corresponding to Upper
Frequency Limit.
2. 7-02 = 1：10V(20mA) corresponding to Lower Frequency Limit，0V (0mA) corresponding to Upper
Frequency Limit.
3.12-6 = 0： 0~10V(0~20mA)
F= I*(3-00)/20 I > =0 ； SW 2=Ｉ or F=V*(3-00) /10 V >=0； SW 2=V
= 1： 2~10V(4~20mA)
F=(I -4)*(3-00) /16 I>=4 ； SW 2=Ｉ
F =0 I <4
F=(V-2)*(3 -00) /8 V > =2； SW 2=V or
F =0 V<2
The setting of figure 1: The setting of figure2:
7-00 7-01 7-02 7-03 7-05 7-00 7-01 7-02 7-03 7-05
A 100﹪ 50% 0 0 100% C 100﹪ 50% 0 1 100%
B 100﹪ 0% 0 0 100% D 100﹪ 0% 0 1 100%
Figure 1 Figure 2
Bias Hz
Bias Hz
100% 60Hz Upper Frequency 100% 60Hz Upper Frequency Limit
C (3-00=60)
A
50% 30Hz
50% 30Hz
0Hz B V D
0V 5V 10V 0Hz V
0V 5V 10V
(0mA) (20mA)
(0mA) (20mA)
The setting of figure 3: The setting of figure 4:
7-00 7-01 7-02 7-03 7-05 7-00 7-01 7-02 7-03 7-05
E 100﹪ 20% 1 0 100% F 100﹪ 50% １ 1 100%
Hz Figure 3 Hz Figure 4
60Hz Upper Frequency Limit 60Hz
Upper Frequency Limit
(3-00=60) (3-00=60)
30Hz 30Hz
Bias Bias F
0% E
0Hz V -0% 0Hz V
-50% 2V 5V 10V
10V -50%
(4mA) (20mA) (20mA)
-100% -100%
4-43
3. The inverter reads the average value of A/D signals once per (7-04×4ms). Users can determine scan
intervals according to noise in the environment. Increase 7-04 in noisy environment, but the respond
time will increase accordingly.
4-44
Parameter Group 8 - Multifunction output terminal and output signal
operation mode
Multifunction analog output control:
8-00：Analog Output Voltage Mode：
0000: Output frequency
0001: Frequency Setting
0002: Output voltage
0003: DC Bus Voltage
0004: Motor current
0005: FEEDBACK Signal of PID
8-01：Analog Output Gain = 0 ~ 200%
The multifunction analog output terminal of the terminal block (TM2), is 0~10Vdc analog output. The
output type is determined by the 8-01. The function of 8-01 is: when there is tolerance for the external
voltage meter and peripheral equipment, please regulate 8-00.
The FEEDBACK value of PID (That is the input voltage and current of S6) outputs analog value from
FM+ terminal. ( decide to parameter 4-06) The value is corresponding to the input signal 0~10V(0 ~ 20
mA) or 2~10V (4~20mA).
※Note: The max output voltage is 10V due to the circuit, even the output voltage should be higher than
10V.
Multifunction output terminals control:
8-02：RELAY1(R1C，R1B，R1A terminal on TM2)
8-03：RELAY2(R2C，R2A terminal on TM2)
0000: Run
0001: Frequency Reached (Target Frequency) (Set Frequency ± 8-05)
0002: Set Frequency (8-04 ± 8-05)
0003: Frequency Threshold Level (> 8-04) - Frequency Reached
0004: Frequency Threshold Level (< 8-04) - Frequency Reached
0005: Over torque Threshold Level
0006: Fault
0007: Auto-restart
0008: Momentary AC Power Loss
0009: Rapid Stop Mode
0010: Coast-to-Stop Mode
0011: Motor Overload Protection
0012: Drive Overload Protection
0013: PID Feedback Signal Break
0014: PLC Operation
0015: Power On
4-45
8-04：Frequency Reached Output Setting =0 ~ 650Hz
8-05：Frequency Output Detection Range =0 ~ 30Hz
4-46
8-02/03= 01：
The preset frequency is reached ( ± 8-05)
8-02/3= 02：
Arbitrary frequency consistency Fout = 8-04 ± 8-05
8-02/3 = 03：frequent detection Fout > 8-04
4-47
8-02/3 = 04：frequent detection Fout < 8-04
8-02/3= 05：over torque detection
4-48
4-49
Parameter Group 9 – Drive and Load Protection Modes

9-00：Trip Prevention Selection During Acceleration:
0000：Enable Trip Prevention During Acceleration
0001：Disable Trip Prevention During Acceleration
9-01：Trip Prevention Level During Acceleration: 50% ~ 300%
9-02：Trip Prevention Selection During Deceleration:
0000：Enable Trip Prevention During Deceleration
0001：Disable Trip Prevention During Deceleration
9-03：Trip Prevention Level During Deceleration: 50% ~ 300%
9-04：Trip Prevention Selection in Run Mode:
0000：Enable Trip Prevention in Run Mode
0001：Disable Trip Prevention in Run Mode
9-05：Trip Prevention Level in Run Mode: 50% ~ 300%
9-06：Trip Prevention Deceleration Time Selection in Run Mode:
0000: Trip Prevention Deceleration Time Set by 3-03
0001: Trip Prevention Deceleration Time Set by 9-07
9-07：Deceleration Time in Trip Prevention Mode (sec): 0.1 ~ 3600.0
1. In acceleration, the inverter will delay the acceleration time if the time is too short resulting in the
over current in order to prevent the inverter trips.
2. In deceleration, the inverter will delay the acceleration time if the time is too short resulting in the
over voltage of DC VUS in order to prevent the inverter trips with ‘OV’ displayed.
3. Some mechanical characteristics (such as press) or unusual breakdown (seize due to insufficient
lubrication, uneven operation, impurities of processed materials, etc.) will cause the inverter to trip,
thus inconvenience users. When the operating torque of the inverter exceeds the setting of 9-05,
the inverter will lower the output frequency following the deceleration time set by 9-06, and return
to the normal operation frequency after the torque get steady.
9-08：Electronic Motor Overload Protection Operation Mode:

0000：Enable Electronic Motor Overload Protection
0001：Disable Electronic Motor Overload Protection
9-09：Motor Type Selection:
0000：Electronic Motor Overload Protection Set for Non-Inverter Duty Motor
0001：Electronic Motor Overload Protection Set for Inverter Duty Motor
9-10：Motor Overload Protection Curve Selection:
0000：Constant Torque (OL=103%)(150%,1 minute)
0001：Variable Torque (OL=113%)(123%,1 minute)
9-11：Operation After Overload Protection is Activated:
4-50
0000：Coast-to-Stop After Overload Protection is Activated
0001：Drive Will not Trip when Overload Protection is Activated (OL1)
Description of the thermal relay function:
1. 9-10 = 0000：protect the general mechanical load, the load is less than 103% rated current, the
motor continue to run. The load is larger than 150% rated current, the motor will run
for 1 minute.(Refer to following curve(1).
= 0001：protect HVAC load(FAN、PUMP…so on)：the load is less than 113% rated current,
the motor continue to run. The load is larger than 123% rated current, the motor will
run for 1 minute.
2. The heat sinking function will declining when the motor run at low speed. So the thermal relay
action level will decline at the same time.(The curve 1 will change to curve 2).
3. 9-09 = 0000：set 0-05 as the rated frequency of the serve motor.
9-11 = 0000：the inverter coast to stop as the thermal relay acts and flash OL1. Press the ‘reset’ or
the external reset terminal to continue to run
= 0001：the inverter continues to run as the thermal relay acts and flash OL1. Till the
current decline to 103% or 113%(determined by 9-10), OL1 will disappear.
9-12：Over Torque Detection Selection:

= 0000：Disable Over Torque Operation
4-51
= 0001：Enable Over Torque Operation Only if at Set Frequency
= 0002：Enable Over Torque Operation while the Drive is in Run Mode
9-13：Operation After Over Torque Detection is Activated:
= 0000：Drive will Continue to Operate After Over Torque is Activated
= 0001：Coast-to-Stop After Over Torque is Activated
9-14：Over Torque Threshold Level (%)：30-200%
9-15：Over Torque Activation Delay Time (s)：0.0-25.0
The over torque is defined as: the output torque is inside parameter 9-15, the voltage level(the inverter
rated torque is 100%) is over 9-14 parameter.
9-13 = 0000：If there is over torque, the inverter can continue to run and flashes OL3 till the output
torque is less than the 9-14 setting value.
= 0001：If there is over torque, the inverter coasts to stop and flashes OL3. it is necessary to press
‘RESET’ or external terminal to continue to run.
Parameter8-02,03(Multifunction output terminal ) = 05, the output terminal is output over torque signal.
※Note: Over torque output signal will be output as the parameter 9-12=0001or 0002 when the level and
time are over the range.
Parameter Group 10 – Volts /Hz Pattern Operation Mode

V/F PATTERN Selection
10-0：V/F PATTERN Selection = 0 – 18
10-1：Torque boost gain(V/F pattern modulation)% = 0.0 – 30.0%
10-2：Motor no load current(Amps AC) -------------
10-3：Motor rated slip compensation(%) = 0.0 – 100.0%
10-4：Max output frequency(HZ) = 0.20 – 650.0Hz
10-5：Max output frequency voltage ratio(%) = 0.0 – 100.0%
10-6：Medium frequency(HZ) = 0.10 –650.0Hz
4-52
10-7：Medium output frequency voltage ratio (%) = 0.0 – 100.0%
10-8：Min output frequency(HZ) = 0.10 –650.0Hz
10-9：Min output frequency voltage ratio (%) = 0.0 – 100.0%
1. 10-0=18, set the V/F pattern freely complying with 10-4~10-9 (Refer to following diagram)
(V)
10-5
(Vmax)
10-7
(Vmid)
10-9
(Vmin)
Hz
10-8 10-6 10-4 650
4-53
2. 10-0 = 0 – 17 V / F Pattern (Refer to following list )。
Netz- Netz-fr
10-0 V/f-Modell 10-0 V/f-Modell
freq. eq.
V(%) V(%)
Standardanwendung
Standardanwendung
100 100
0 9
0.1 3 0.1 3
V(%) V(%)
Hohes Anzugsdrehmoment
Hohes Anzugsdrehmoment
10
1 100 100
11
2
0.1 3 12 0.1 3
3
50Hz 60Hz
V(%) V(%)
Variables Drehmoment
Variables Drehmoment
4 100 13 100
5 14
0.1 25 0.1 30
V(%) V(%)
Konstantes Drehmoment
Konstantes Drehmoment
6 15
100 100
7 16
8 17
0.1 5 0.1 6
4-54
10-0 B C
0/9 50.0% 1.0%
1 / 10 60.0% 1.0%
2 / 11 65.0% 1.0%
3 / 12 70.0% 1.0%
4 / 13 40.0% 1.0%
5 / 14 35.0% 1.0%
6 / 15 45.0% 1.0%
7 / 16 55.0% 1.0%
8 / 17 65.0% 1.0%
3. The inverter will output the value that B, C voltage (refer to 10-0) plus 10-1 V/F pattern setting.
And the start torque will be raised.
Voltag
100%
10-1=
Hz
1 50/6
2 5/3
※Note: 10-1=0, Torque boost function is invalid
4. When the induction motor is in running, there must be slip due to the load. It is necessary to boost to
improve the precision of the speed.
Output Current-(10-2) Note : 0-02=motor rated current
Slip frequency boost = × (10-3)
(0-02)-(10-2) 10-2=motor no load current
10-3 rough value= (Motor synchronization speed– Rated speed) / Motor synchronization speed
Marked on the motor nameplate

120
Motor synchronization speed (RPM)= × Motor rated frequency (50Hz or 60Hz)
Motor Poles
120
eg: 4 Poles，60Hzinduction motor synchronization speed = × 60=1800 RPM
4
※Note: Motor no load current(10-2) differs with the inverter capacities（15-0）(Refer to 0-02 note)，
It should be regulated according to the actual condition.
4-55
Parameter group 11 - PID operation mode
11-0：PID Operation Selection
0000: PID disable

0001: PID enable (Deviation is D-controlled)
0002: PID Feedback D-controlled
0003: PID D Reverse characteristic controlled
0004: PID Feedback D characteristic controlled
0005: PID, Frequency command + D controlled
0006: PID, Frequency command + Feedback D controlled
0007: PID, Frequency Command + D reverse Characteristic controlled.
0008: PID, Frequency Command + Feedback D reverse Characteristic controlled.
11-0 =1, D is the deviation of (target value –detected value) in the unit time (11-4).
=2, D is the deviation of the detected values in unit time (11-4).
=3, D is the deviation of (target value – detected value) in the unit time (11-4). If the deviation
is positive, the output frequency decreases, vice versa.
=4, D is the deviation of detected value in unit time (11-4). When the deviation is positive, the
frequency decreases, vice versa.
=5, D is equal to the deviation of (target value – detected value) in unit time (11-4) +Frequency
command.
=6, D is equal to the deviation of detected values in unit time + Frequency command.
=7, D is equal to the deviation of (target value – detected value) in unit time +Frequency
command. If the deviation is positive, the output frequency decreases, vice versa.
=8, D is equal to the deviation of detected values in unit time + Frequency command. When the
deviation is positive, the frequency decreases, vice versa.
11-1：Feedback Calibration Gain(%) ： 0.00 - 10.00
11-1 is the calibration gain. Deviation = (target value – detected value) × 11-1
11-2：Proportion Gain(%) ： 0.00 - 10.00
11-2：Proportion gain for P control.
11-3：Integrate Time（s）：0.0 - 100.0
11-3：Integrate time for I control
11-4：Differential Time（s）：0.00 - 10.00
11-4：Differential time for D control
4-56
11-5: PID Offset : 0000 : Positive Direction
0001 :Negative Direction
11-6: PID Offset Adjust (%) : -109% ~ +109%
11-5/11-6：PID the calculated result pluses 11-6 (the sign of 11-6 is determined by 11-5).
11-7：Output Lag Filter Time（s）：0.0 - 2.5
11-7：update time for output frequency.
※Note: PID Function is available for controlling the output flow, external fan flow and temperature.
The controlling flow is as follow:
1. Performing PID control, set 5-05=23, AI2 (S6) on TM2 as PID feedback signal.
2. The target value of above diagram is the 1-06 input frequency.
3. There are two ways to see the PID feedback signal, one is using the Keypad switch display (4-06
must be setting as 1), the other is using analog output FM+ (8-00 must be setting as 5).
4-57
Parameter Group 12 - PID "Limits" and "Out of Range" Mode
12-0：Feedback Loss Detection Mode: 0000:Disable
0001:Enable – Drive Continues to Operate After Feedback Loss

0002:Enable – Drive “STOPS” After Feedback Loss
12-0= 0：Disable; 12-0= 1：detect to run and display PDER；12-0= 2：detect to stop and display
PDER。
12-1：Feedback Loss Detection Mode (%)：0 - 100
12-1is the level for signal loss. Deviation = Command value – Feedback value. While the deviation
is larger than the loss level, the feedback signal is lost.
12-2：Feedback Loss Detection Delay Time (s)：0.0 -25.5
12-2：the action lay time as the feedback signal lost.
12-3：Integrate Limit Value (%)：0 - 109
12-3：the Limiter to prevent PID saturating.
12-4：Integrator Reset to 0 when Feedback Signal Equals the Intended Value:
0000:Disable
0001:1 second
0030: 30 seconds
12-4=0：As PID feedback value reaches the command value, the integrator will not be reset to 0.
12-4=1~30：As PID feedback value reaches the target value, reset to 0 in 1~30 seconds and inverter
stops output. The inverter will output again as the feedback value differs from the target
value.
12-5：Allowable Integration Error Margin (Unit Value) (1 Unit = 1/8192)：0 - 100
12-5=0 ~ 100% unit value：restart the tolerance after the integrator reset to 0.
12-6：PID Feedback Signal：0000: 0~10V or 0~20mA
0001: 2~10V or 4~20mA
12-6：Feedback signal selection, 12-6=0：0~10V o r 0~ 20mA (s igna l V or I dec id e to SW2)

4-58
12-6=1：2~1 0 V or 4~20mA( s ig na l V or I dec id e to SW2)
12-7, 12-8：PID Sleep Mode
PID SLEEP MODE:

11-0=1(PID Enable)
5-05=20(PID FEEDBACK Enable)
1-06=PID setting frequency source (Target Value)
12-7 Set the frequency for sleep start, Unit：HZ
12-8 Set the Time for sleep delay, Unit：sec
When PID output frequency is less than the frequency for sleep start and the reaches the time of sleep
delay, the inverter will decelerate to 0 and enter PID sleep mode.
When PID output frequency is larger than the frequency for sleep start the inverter will be awaked and
enter PID awake mode. The time diagram is as follow:
Parameter Group 13 - Communication mode
13-0：Assigned Communication Station Number：1 - 254
13-0: to set the communication station codes which are suitable for driving more than one inverters
situations.
4-59
13-1：Baud Rate setting (bps)： 0000: 4800
0001: 9600
0002: 19200
0003: 38400
13-2：Stop Bit Selection：0000: 1 stop bit
0001: 2 stop bit
13-3：Parity Selection ：0000 : no parity
0001 : even parity

0002 : odd parity
13-4：Data Format Selection：0000 :8 bit data
0001 :7 bit data

1.RS-485 Communication：
(1)1 vs 1 Controlling：to control one inverter by a PC or PLC or controller.(set 13-0 = 1~254)
(2)1 vs more Controlling：to control more than one inverters by PC or PLC or Controller (The max
number of inverter could be 254. set 13-0 = 1~254), when the inverter receives the communication
station code = 0, the communication controlling is acceptable regardless the setting value of 13-0.
2. RS-232communication: (RS232 interface is required)
1vs1 controlling: to control one inverter by a PC or PLC or controller. (Set 13-0 = 1~254)
※Note:
a. The BAUD RATE (13-1) of PC (or PLC or Controller) and the one of the inverter should be set as
the same .Communication format (13-2/13-3/13-4) should be set as the same.
b. The inverter will confirm the parameter efficient as PC modifies the parameter of the inverter.
c. Please refer to the 7300CV Communication PROTOCOL.
Parameter Group 14 - Auto Tuning
14-0：Stator Resistance(Ohms) Gain
14-1：Rotator Resistance(Ohms) Gain
14-2：Equivalent Inductance(mH) Gain
14-3：Magnetized Current(Amps AC) Gain
14-4：Ferrit Loss Conduction (gm) Gain
4-60
1. If 0-00=0 or 1(vector mode ) is selected, as power ON, set 0-06=1, the motor will run as the
inverter performs auto tuning. As the motor stop, it means that auto tuning finished. The inverter
will write the internal parameter of the motor to 14-0~ 14-4, and auto reset the 0-06 as 0.
2. Auto tuning must be carried out as long as the motor changed. If the internal parameters is known
already, they can be input to 14-0~14-4 directly.
3. 0-06=1，to perform auto tuning, after finished, 0-06 auto reset to 0, the Keypad displays END.
4.The parameter group only affect the current vector.
Parameter Group 15 - Operation Status and Function Reset
15-0：Drive Horsepower Code
15-0 Inverter Model 15-0 Inverter Model

2P5 R500AC/BC 401 0001BE
201 0001AC/BC 402 0002BE
202 0002AC/BC 403 0003BE
203 0003AC/BC 405 0005BE
205 0005BC 408 7R50BE
208 7R50BC 410 0010BE
JNTHBCBA
210 0010BC 415 0015BE
JNTHBCBA
215 0015BC 420 0020BE
220 0020BC 425 0025BE
225 0025BC 430 0030BE
230 0030BC 440 0040BE
240 0040BC 450 0050BE
460 0060BE
475 0075BE
15-1：Software Version
15-2：Fault Jog（Latest 3 times）
1. When the inverter doesn’t work normally, the former fault log stored in2.xxxx will be transferred
to 3.xxxx, then, the one in 1.xxxx to 2.xxxx. The present fault will be stored in the blank 1.xxxx.
Thusly, the fault stored in 3.xxxx is the earliest one of the three, while the one 1.xxxx is the latest.
2. Enter 15-2, the fault 1.xxxx will be displayed firstly, press▲, you can read 2.xxx→3.xxx→1.xxx,
whereas▼, the order is 3.xxx→2.xxx→1.xxx→3.xxx.
3. Enter 15-2, the three fault log will be cleared as the reset key is pressed. The log content will
changed to 1.---，2.---，3.---.
4-61
4. E.g. if the fault log content is ‘1.OCC’ which indicates the latest fault is OC-C, and so on.
15-3：Accumulated Operation Time 1 (Hours): 0 – 9999
15-4：Accumulated Operation Time 2 (Hours X 10000): 0 - 27
15-5：Accumulated Operation Time Mode: 0000: Power on time
0001: Operation time

1. When the operation time is to 9999 as the operation duration 1 is set. The next hour will be carried
to operation duration 2. Meanwhile, the recorded value will be cleared to 0000, and the record
value of operation duration 2 will be 01.
2. Description of operation time selection:
Preset value Description

0 Power on, count the accumulated time.
1 Inverter operation, count the accumulated operation time
15-6：Reset the factory setting: 1110: Reset the 50Hz factory setting
1111: Reset the 60Hz factory setting

1112: Reset PLC program
As 15-6 is set as 1111, the parameter will be reset to factory setting. The max output voltage will
comply with the voltage and frequency (0-01/0-05) on the nameplate of the motor. The output
frequency is 60Hz if the upper frequency limit is not set.
※Note:
Motor parameters (14-0~14-4) will be modified under V/F control mode when reset factory setting.
On the contrary, motor parameters (14-0~14-4) will not be modified under vector control mode
when reset factory setting.
4-62
4.5 Specification Description on Built-in PLC Function

7300CV has Built-in simple PLC function, user can download Ladder Diagram from PC (Windows
base software) or PDA (WinCE base software) very friendly.
4.5.1 Basic Instruction
¿ À P NO / NC
Input Instruction I i I1∼I7 / i1∼i7

Output Instruction Q Q Q Q Q q Q1∼Q2 / q1∼q2
Auxiliary Instruction M M M M M m M1∼MF / m1∼mF
Special Register V1~V7
Counter Instruction C C c C1~C4 / c1~c4
Timer Instruction T T t T1∼T8 / t1∼t8
Analog Comparing Instruction G G g G1∼G4 / g1∼g4
Encoder Comparing Instruction H H h H1~H4 / h1~h4
Operation Instruction F F f F1~F8 / f1~f8
Description for Special Register

V1: Setting Frequency Range: 0.1~650.0Hz
V2: Operation Frequency Range: 0.1~650.0Hz
V3: AIN Input value Range: 0~1000
V4: S6 Input Value Range: 0~1000
V5: Keypad VR Input Value Range: 0~1000
V6: Operation Current Range: 0.1~999.9A
V7: Torque Value Range: 0.1~200.0%
Upper differential Lower differential Other Instruction Symbol

Differential Instruction D d
SET Instruction ¿
RESET Instruction À
P Instruction P
Open circuit (On status) “ ”

Short circuit (Off status) “ -- ”
Connection symbol Description

─ Connecting left and right Components
┴ Connecting left, right and upper Components
┼ Connecting left, right, upper and lower Components
┬ Connecting left, right and lower Components
4-63
4.5.2 Function of Basic Instruction
Function D (d) Command
Sample 1: I1─D ──[ Q1
I1 OFF ON OFF
D OFF ON OFF
One complete scan period
Q1 OFF ON OFF
Sample 2: i1─d ──[Q1
I1 OFF ON OFF
I1 is the reverse phase of i1.
i1 ON OFF ON
d1 OFF ON OFF
One complete scan period
Q1 OFF ON OFF
NORMAL ( - [ ) Output
I1 ── [Q1
I1 OFF ON OFF
Q1 OFF ON OFF
◎ SET (¿) Output
I1 ── ¿Q1
I1 OFF ON OFF
Q1 OFF ON
RESET (À) Output
I1 ── ÀQ1
I1 OFF ON OFF
Q1 ON OFF
P Output
i1 ──PQ1
I1 OFF ON OFF ON OFF ON OFF
I1 is the reverse
phase of i1.
i1
Q1 ON OFF ON OFF
4-64
4.5.3 Application Instructions

Counter
Symbol Description
1 c Counting Mode (1-4)

d Use (I1 ~ f8) to set counting up or counting down
OFF: counting up (0, 1, 2, 3, 4….)
2 4 ON: counting down ( ….3, 2, 1, 0)
e Use (I1 ~ f8) to RESET the counting value
5 6 ON: the counter is initialized to zero and h OFF
3 OFF: the counter continues to count
f Preset Counting Value
g Target (Setting) Value
h Code of the counter (C1 ~ C4 total: 4 groups).
(1) Counter Mode 1
4-65
Sample:
Input under the Ladder Program Mode
The ON/OFF of C3 input count pulse

I1 ─ i2 ─ -- ─﹝C3 is controlled by I1 and i2.
C3 ─ -- ─ -- ─﹝Q1
m1 ┬ -- ─ q1 ─﹝M2
M2 ┴
Input under the Function Program Mode
Count up/down Current Count Value
1 ┐
When the target value is reached, C3 =ON.
M2 │
0000
The input point C3 in the ladder program should be
│─
0020 C3
I3 ON.
┘
I3 ON the counter Target (Setting) value

is reset to zero for the counter
4-66
(2) Counter Mode 2
※Note:
Under this Mode, the counting preset value appeared will be greater than 20, unlike the Mode
1 in which the value is locked at 20.
(3) The counter Mode 3 is similar to the counter Mode 1 except that the former can memory the
recorded value after the power is cut off and continued counting when the power is turned on at
the next time.
(4) The counter Mode 4 is similar to the counter Mode 2 except that the former can memory the
recorded value after the power is cut off and continued counting when the power is turned on at
the next time.
4-67
Timer
Symbol Description
1
c Timing Mode (1-7)
d Timing unit
2 4 1: 0.0 – 999.9 sec
2: 0 – 9999 sec
5 6 3: 0 – 9999 min
3 e Use (I1 ~ f8) to RESET the timing value.
ON: the counter is reset to zero and h OFF
OFF: the counter continues to count
f Preset Timing Value
g Target (setting) Timing Values
h The code of the Timer (T1 ~T8 total: 8 groups).
(1) Timer Mode 1 (ON-Delay A Mode)
4-68
Sample:
I1 ─ -- ─ -- ─﹝T5 When I1 = ON, the fifth Timer starts operating
T5 ─ -- ─ -- ─﹝Q1
Timing unit = 0.1 sec Timer Mode 1
1 ┐
1 │
000.0
│─
When the time reaches to the target value
010.0 T5
10.0 sec, T5 is ON
┘
Target (setting) value Current value

in timer in timer
(2) Timer Mode 2 (ON-Delay B Mode)
4-69
(3) Timer Mode 3 (OFF-Delay A Mode)
(4) Timer Mode 4 (OFF-Delay B Mode)
4-70
(5) Timer Mode 5 (Flash A Mode)
(6) Timer Mode 6 (Flash B Mode)
(7) Timer Mode 7 (Flash C Mode)
4-71
Analog comparator
1 Symbol Description
c Analog comparison mode (1-3)

2 3 d Selection of the input comparison value
e Analog input value
4 6
f Setting reference comparison value (upper limit)
5 g Setting reference comparison value (lower limit)
h Output terminals of analog comparator (G1-G4)
Analog Comparison Mode (1-3)

(1) Analog comparator mode 1 (e ≤ g, h ON)
(2) Analog comparator mode 2 (e ≥ f, h ON)
(3) Analog comparator mode 3 (g ≤ e ≤ f, h ON)
Selection of the input comparison value (V1-V7)

(1) The input comparison value =V1: Setting Frequency
(2) The input comparison value =V2: Operation Frequency
(3) The input comparison value =V3: AIN Input Value
(4) The input comparison value =V4: AI2 Input Value
(5) The input comparison value =V5: Keypad VR input Value
(6) The input comparison value =V6: Operation Current
(7) The input comparison value =V7: Torque Value
4-72
Encoder input Comparing Instruction
Symbol Description
1
c Encoder control mode (1-2)
2 4 Use (I1 ~ f8) to set counting up or counting down
d OFF: counting up (0, 1, 2, 3, 4….)
5 7 ON: counting down ( ….3, 2, 1, 0)
3
e Use (I1~f8) to Reset counting value.
6
f A1, Encoder Input Value/Encoder dividing ratio(h)
g A2, Setting comparing value
h C, Encoder dividing ratio
i Encoder comparing output terminal, H1~H4
(1) Control Mode 1
Encoder Comparing Function: A1/C A2 Comparing Output
(2) Control Mode 2
Encoder Comparing Function: A1/C A2 Comparing Output
※Comparison Enable/ Disable of the Encoder input value is determined by the Ladder Program ON/OFF.
Running Instruction
4-73
Symbol Description
5 c Running mode could be set via I1~f8

1
OFF：(FWD)
2 6
ON：(REV)
3 7 9
d Segment Speed could be set via I1~f8
4 OFF：Operating at the frequency set on i
8
ON：Operating at the frequency set on j
e Select constant or V3, V5 for Setting Frequency

f Select constant or V3, V5 for Preset Speed
g Acceleration Time
h Deceleration Time
Sample: i Setting Frequency (Could be a constant or V3, V5)
j Segment Speed (Could be a constant or V3, V5)
k
Instruction code of operation (F1~F8，Total: 8 Groups)
ON/ OFF of I1 controls the Run/Stop
I1 ─ -- ─ -- ─﹝F1 status of F1.
F1 ─ -- ─ -- ─﹝Q1
10.0
M1 ┐ When Inverter operating, F1=ON.
M2 10.0
n The input terminal of F1 in the ladder program
│
60.00 F1
n mode should be ON.
30.00
│─
4-74
Chapter 5 Troubleshooting and maintenance
5.1. Error display and remedy

5.1.1. Errors which can not be recovered manually
Display Error Cause Remedy
Connect a parallel RC burst
CPF Program absorber across the magnetizing
External noise interference
problem coil of the magnetic contactor
that causes interference
EEPROM
EPR Faulty EEPROM Replace EEPROM
problem
Voltage too high Send the inverter back for

@ -OV- Detection circuit malfunction
during stop repairing
1. Power voltage too low 1. Check if the power voltage
2. Restraining resistor or fuse was correct or not
@ -LV- Voltage too low burnt out. 2. Replace the restraining
during stop 3. Detection circuit resistor or the fuse
malfunctions 3. Send the inverter back for
repairing
1. Detection circuit 1. Send the inverter back for
The inverter is
@ -OH- malfunctions repairing
overheated
2. Ambient temperature too high 2. Improve ventilation
during stop
or bad ventilation conditions
CTER Current Sensor Current sensor error or circuit Send the inverter back
detecting error malfunctions for repairing
※ Note：〝@ 〞the Failure contact does not function.
5-1
5.1.2. Errors which can be recovered manually and automatically

1. the motor wind and
1. inspect the motor
Over current at enclosure short circuit
OC-S 2. inspect the wire
start 2. the motor contacts and earth
3. replace the transistor module
short circuit
3. the IGBT module ruined
Over-current at The preset deceleration time is
OC-D deceleration too short.
Set a longer deceleration time
1. Acceleration time too short
2. The capacity of the
1. Set a longer acceleration time
motor higher than the
2. Replace a inverter with the
capacity of the inverter
same capacity as that of the
OC-A Over-current at 3. Short circuit between
motor
acceleration the motor coil and the
3. Check the motor
shell
4. Check the wiring
4. Short circuit between
5. Replace the IGBT module
motor wiring and earth
5. IGBT module damaged
1.Increase the capacity of the

inverter
2.Rerun parameter auto tuning
OC-C Over-current at 1. Transient load change
(0-06 = 1)
fixed speed 2. Transient power change
3. Reduce stator resistance (14-0)
if the above remedies are
helpless
1. Set a longer deceleration time

2. Add a brake resistor or brake
Voltage too high 1. Deceleration time setting too
module
OV-C during operation/ short or large load inertia
3. Add a reactor at the power input
deceleration 2. Power voltage varies widely
side
4. Increase inverter capacity
Illegal interrupt Send back to repair if it happens
Err4 Outside noise interference
of CPU many times
Over speed during 1. Moter load too big or Inverter 1. Increase acceleration /
operating capacity too small deceleration time (3-02/3-03)
2. Moter parameter error 2. Input correct motor
OVSP (vector mode) Parameter
3. The gain is too big during 3.Change stator Resistance gain
vector mode operating and Rotator resistance gain
4. The Current detect circuit (14-0/14-1), suggest that
fault decrease 50~100, until 0
4. Send back to Teco
5-2
5.1.3 Errors which can be recovered manually but not auto matically
1. Detection circuit
1.Check the noise between Power
Over-current during malfunctions
OC line and motor line
stop 2. Bad connection for CT
2.Send the inverter back for
signal cable
repairing
1. Heavy load 1. Increase the motor capacity

OL1 Motor overload 2. Inappropriate settings of
0-02, 9-08~11 2. set 0-02, 9-08~11 properly
OL2 Inverter overload Heavy Load Increase the inverter capacity
1. Heavy Load 1. Increase the inverter capacity

OL3 Over torque 2. Insufficient settings of 9-14,
9-15 2. set 9-14, 9-15 properly
1. Improve power quality or
increase the value of 2-01
LV-C Voltage too low 1. Power voltage too low 2. Set a longer acceleration time
during operation 2. Power voltage varies widely 3. Increase inverter capacitor
4. Add a reactor at the power input
side
1. Check if there are any
Heatsink
1. Heavy load problems with the load
OH-C temperature
2. Ambient temperature too 2. Increase inverter capacity
too High during
high or bad ventilation 3. Improve ventilation
operation
conditions
5-3
5.1.4 Special conditions
Display Error Description
STP0 Zero speed stop Happened when preset frequency <0.1Hz
1. If the inverter is set as external terminal control mode (1-00=1) and

direct start is disabled (2-04=0001), the inverter cannot be started
STP1 Fail to start directly and will flash STP1 when operation switch turned to ON after
applying power (refer to descriptions of 2-04).
2. Direct start is possible when 2-04=0001.
1. If the inverter is set as external control mode (1-00=0001) and Stop

key is enabled (1-03=0000), the inverter will stop according to the
setting of 1-05 when Stop key is pressed. STP2 flashes after stop.
Turn the operation switch to OFF and then ON again to restart the
inverter.
Keypad
STP2 2. If the inverter is in communication mode and Stop key is enabled (1-
emergency stop
03=0000), the inverter will stop in the way set by 1-05 when Stop
key is pressed during operation and then flashes STP2. The PC has
to send a Stop command then a Run command to the inverter for it to
be restarted.
3. Stop key cannot perform emergency stop when 1-03=0001
The inverter will ramp stop and then flash E.S., when input external
External
E.S. emergency stop signal via the multifunctional input terminal (refer to
emergency stop
descriptions of 5-00~5-06).
The inverter stops immediately and then flashes b.b., when external
b.b. External base
base block is input through the multifunctional input terminal (refer
block
to descriptions of 5-00~5-06).
1. Motor data error resulting in for auto-tuning failure

ATER Auto-tuning faults
2. Stop the inverter emergently during Auto-tuning
PDER PID feedback loss PID feedback loss detect
5-4
5.1.5 Operation errors

Parameter and
1.Attempt to modify frequency 1. Set 3-17=0000
frequency
LOC /parameter while 3-17>0000
reverse already 2. Set 1-02=0000
2.Attempt to reverse while 1-02=0001
locked
1.The ▲ or▼ is
1.Press ▲ or ▼while 1-06>0 or available for modifying
Key running at preset speed. the parameter only
Err1 operation error 2.Attempt to modify the parameter can
when 1-06=0
not be modified during operation 2.Modify the parameter
(refer to the parameter list). while STOP
1. 3-01in the range of 3-13 ± 3-16 or
Parameter setting 3-14 ± 3-16or 3-15 ± 3-16
1. Modify 3-13~3-15or 3-16
Err2 error 2. 3-00≤3-01 2. 3-00>3-01Set 1-00=0, 1-
3.The setting error as performing Auto 06=0 during Auto tuning
tuning(e.g. 1-00 ≠ 0，1-06 ≠ 0 )
1. Issue enable command
Err5 Modification of 1. Issue a control command during
before communication
parameter is communication disabled
2. Set the very parameter
not available in 2.Modify the function 13-1~13-4
of the function before
communication during communication
communication
1. Wiring error
Err6 Communication 2. Communication parameter setting
1.Check hardware and wiring
failed error.
2.Check Function 13-1~13-4
3. Sum-check error
4. Incorrect communication protocol
1. Attempt to modify the function 15-0
Err7 Parameter or 15-7
If Reset inverter is not
available, please send the
conflict 2. Voltage and current detection circuit
inverter back for repair
is abnormal
Err8
Factory setting When PLC is Running, Perform Please perform factory
error factory setting setting before PLC stops.
EPr1 Parameter setting 1.Set 3-18=1.2 without connecting

1.Modify 3-18
error copy unit copy unit.
2.Replace copy unit
failed 2. Copy unit failed.
EPr2
Parameter not Copy the parameter to inverter to 1.Rewrite again
match verify the parameter is not match. 2.Replace copy unit
5-5
5.2 General troubleshooting

Status Checking point Remedy
Is power applied to L1(L), L2, and L3(N) ‧Is the power applied?
terminals (is the charging indicator lit)? ‧Turn the power OFF and then ON again.
‧Make sure the power voltage is correct.
‧Make sure screws are secured firmly.
Are there voltage across the output terminal
‧Turn the power OFF and then ON again.
T1, T2, and T3?
Is overload causing the motor blocked? ‧Reduce the load to let the motor running.
Motor can
Are there any abnormalities in the inverter?
not run ‧See error descriptions to check wiring and
Is forward or reverse running command issued? correct if necessary.
‧ Is analog frequency input signal wiring

Has analog frequency signal been input? correct?
‧Is voltage of frequency input correct?
‧Operate operations through the digital

Is operation mode setting correct?
panel.
Are wiring for output terminals T1, T2, and T3 ‧Wiring must match U, V, and W terminals
correct? of the motor.
Motor runs
inversely
Are wiring for forward and reverse signals ‧Check wiring are correct if necessary.
correct?
Are wiring for analog frequency inputs correct? ‧Check wiring are correct if necessary.
The motor
speed can
not be
Is the setting of operation mode correct? ‧Check the operation mode of the operator.
regulated.
Is the load too heavy? ‧Reduce the load.
Are specifications of the motor (poles, ‧Confirm the motor’s specifications.

Motor voltage…) correct?
running
speed too Is the gear ratio correct? ‧Confirm the gear ratio.
high or too
low Is the setting of the highest output frequency ‧Confirm the highest output frequency.
correct?
Motor speed Is the load too heavy? ‧Reduce the load.
varies
‧Minimize the variation of the load.
unusually
Does the load vary largely? ‧Increase capacities of the inverter and the
motor.
5-6
‧Add an AC reactor at the power input side

Is the input power lack of phase? if using single-phase power.
‧Check wiring if using three-phase power.
5-7
5.3 Quick troubleshooting of 7300CV
7300CV INV Fault
Is fault fully NO
understood?
YES
Any
Symptoms other than burn NO symptoms of burn YES Check burnt and damaged
out, damage, or fuse meltdown in parts
the inverter?
out and damage?
YES
Abnormal NO
signal? Is the main circuit NO Replace DM
DM intact?
Check according to displayed

abnormal messages YES
Is the fuse NO Replace fuse

intact？
YES
Is the main circuit NO Replace I.G.B.T

I.G.B.T intact?
Visually check controller and YES
driver boards
YES
Any abnormalities in 有 Replace the abnormal boards
appearances?
Apply the power
Are displays and

indicators of the NO
operating unit working
normally?
YES Is LED lit? NO Replace the burst absorber
Any abnormal NO
display? YES
Any abnormal Is the DC input voltage NO

controlling the power
Check terminals and wiring
display?
What’s the correct
message? YES
3 abnormal values Is +5V control NO Replace the driver board

in 15-2 voltage correct?
Check 3 abnormal values of 15-2
with ▼key. YES
Replace control board and
digital operating unit
Is the error eliminated NO

after replacing control
board?
YES The inverter faults
Perform detailed check
*to next page
5-8
*to previous page

Check parameters of inverter
Perform parameter
initializations
Specify operation control

mode
FWD or REV LED NO Replace the control board

light after flashes
YES
Set up frequency command
Is the frequency value NO

Replace the control board
displayed in operation
unit
YES
Are there NO
voltage outputs in output Replace the control board
terminals U, V and W
YES
Connect the motor to run Is the control NO
board working well after
replacement
YES
Is there any YES

abnormal display?
NO
Are output NO
current of each phase
even?

The inverter is OK
5-9
Troubleshooting for OC, OL error displays

The inverter displays OC, OL
errors
Is the main circuit NO Replace I.G.B.T

I.G.B.T working
YES
Any abnormalities in Replace faulty circuit board

appearances?
Apply the power
YES
Any abnormal NO
Is the current detector
indications?
OK?
YES
Input operation command Replace control board Replace the current controller
Is FWD LED keeping Replace control board

lit after flash? NO
YES
Input frequency command
Is the output frequency of the NO Replace control board

operating unit displayed?
YES
Are there NO
voltage output at U,V and W output Replace control board
terminals?
YES
Is the inverter
NO
Connect the motor to run working well after
replacement
Any abnormal values YES YES

displayed?
NO
Any output current of NO

each phase even?

The inverter’s output is OK
5-10
Troubleshooting for OV, LV error

The inverter displays OV, LV
NO Replace the main circuit fuse

Is the main circuit fuse
intact？
YES
YES Replace the faulty circuit

Any abnormalities in
appearances? board
NO
Apply the power
Any abnormal YES Replace the control board

indications?
NO
Input operation command
Is FWD LED keeping Replace the control board

lit after flash? NO
YES
Input frequency commands
Is the output frequency of the NO

Replace the control board
operating unit displayed?
YES
Are there NO
voltage output at T1,T2,T3 Replace the control board
output terminals?
Is the inverter NO
YES working well after
Connect the motor to run replacement
YES
YES
Any abnormal value?
NO
Any current of all NO

phase even?

The inverter’s output is OK
5-11
The motor can not run
YES Is MCCB
applied?
NO
Can MCCB be NO
applied? Short circuited wiring
YES (within ±10% of the normal value)
Are voltages NO ˙The power is abnormal

between power
terminals correct? ˙Bad wiring
Is LED 101lit? NO
7300CV fault
Is the operation switch NO The operation switch is set to

in “RUN’ position “RUN’ position
YES
Are there outputs between NO

U,V,W terminals of the motor 7300CV fault
Are outputs between NO

U,V,W even 7300CV fault
YES (voltage deviation between pairs are even if within ±3%

of the normal value without the motor connected)
˙Motor
˙Motor faults
˙Bad wiring
5-12
The motor is overheated
Is load or current Reduce the load.

YES Increase capacities of
exceeding the specified
value? 7300CV and the motor.
NO
Is it running at low YES

Select the motor again
speed for a long
time?
NO
Are voltage between 7300CV faults

U-V,V-W,W-U correct?
YES (within ±3% of the normal value)

Is there any YES
deterrence preventing Clear the deterrence
cooling the motor
NO
Bad connection between YES Correct the bad connection
7300CV and the motor
Motor runs unevenly
Does it happen YES Is the NO

acceleration time Increase the acc/ dec time
in decelerating?
correct?
NO Reduce the load.
YES
Increase capacities of
7300CV and the motor.
Are output voltages NO

between U-V,V-W,W-U 7300CV faults
balanced?
YES (within ±3% of rated output voltage

Is the load YES Reduce the load floating or
floating? add a flywheel.
NO
Vibration degree in transmission Input the mechanical system

parts such as gears?
Small 7300CV faults
5-13
5.4 Routine inspection and period inspection

To ensure stable and safe operations, check and maintain the inverter regularly and
periodically.
The table below lists the items to be check to ensure stable and safe operations.
Check these items 5 minutes after the “Charge” indicator goes out to prevent service
persons from being hurt by residual electric power.
Checking
Items Details period Methods Criteria Remedies
Daily 1Year
Measure with
Confirm the Temperature:
thermometer and
temperature and -10 – 40oC
○ hygrometer
Circumstances humidity around Humidity: Below
according to Improve the
around the the machine 95% RH
installation notices. circumstances
machine
Are there
inflammables ○ Visual check No foreign matters
piled up around?
Any unusual vibration
○ Visual, hearing No foreign matters Secure screws
from the machine
Installation 200V series: below
and grounding Measure the 100Ω
Is the grounding Improve the
of the inverter ○ resistance with a
resistance correct? 400V series: below grounding
multi-tester
10Ω
Voltage must
Input power Is the voltage of the Measure the voltage Improve input
○ conform with the
voltage main circuit correct? with a multi-tester voltage
specifications
External Are secure parts
○
terminals and loose?
Visual check
internal Is the terminal base Secure or send
mounting ○ Check with a No abnormalities
back for repair
damaged? screwdriver
screws of the
inverter
Obvious rust stains ○
Deformed or crooked ○
Replace or
Internal wiring Any damage of the Visual check No abnormalities send back for
of the inverter wrapping of the ○ repair
conducting wire
Heap of dust or Clean up
Heat sink ○ Visual check No abnormalities
mingled trifles heaped dust
Heap of conductive
○
metal or oil sludge Clean up or
Printed
Discolored, Visual check No abnormalities replace the
circuit board
overheated, or ○ circuit board
burned parts
Unusual vibration and Visual or hearing Replace the
○
noise check cooling fan
Cooling fan No abnormalities
Heap of dust or
○ Visual check Clean up
mingled trifles
Heap of dust or
○ Visual check No abnormalities Clean up
mingled trifles
Power Replace
Check resistance No short circuit or
component Measure with a power
between each ○ broken circuit in
multi-tester component or
terminals three-phase output
inverter
Any unusual odor or Replace
Capacitor ○ Visual check No abnormalities
leakage capacitor or
5-14
Any inflation or inverter

○
protrusion
5.5 Maintenance and Inspection
Inverter doesn’t need daily inspection and maintenance.
To ensure long-term reliability, follow the instructions below to perform regular
inspection. Turn the power off and wait for the charge indicator (LED101) to go out
before inspection to avoid potential shock hazard possibly caused by charges resides
in high-capacity capacitors.
(1) Clean up the accumulation of muck inside the inverter.

(2) Check if there are any loose terminal screws and securing screws. Tighten all
loose screws.
(3) Insulation tests
(a) Disconnect all leads connecting T-VERTER with external circuit when
performing insulation tests against external circuit.
(b) Internal insulation test should be performed against the main circuit of the T-
VERTER body only. Use a high resistance DC 500V meter with insulating
resistance higher than 5MΩ.
Caution! Do not perform this test against the control circuit.
L1(L) T1(V)
Power source Hookup of insulation test
L2 T-VERTER T2(V)
Motor
L3(N) T3(V)
Ground terminal
Ground terminal
DC-500V high resistance meter
5-15
Chapter 6 Peripherals Components

6.1 Reactor specification at Input side
AC inductance at input side AC inductance at input side
Model
Model Inductance Inductance
Current (A) Current (A)
(mH) (mH)
R500-AC/BC 5.0 2.1 0001-BE 2.5 8.4
0001-AC/BC 5.0 2.1 0002-BE 5.0 4.2
0002-AC/BC 10.0 1.1 0003-BE 7.5 3.6
0003-AC/BC 15.0 0.71 0005-BE 10.0 2.2
0005-BC 20.0 0.53 7R50-BE 15.0 1.42
7R50-BC 30.0 0.35 0010-BE 20.0 1.06
JNTHΧΧBA-
0010-BC 40.0 0.265 0015-BE 30.0 0.7
JNTHΧΧBA-
0015-BC 60.0 0.18 0020-BE 40.0 0.53
0020-BC 80.0 0.13 0025-BE 50.0 0.42
0025-BC 90.0 0.12 0030-BE 60.0 0.36
0030-BC 120.0 0.09 0040-BE 80.0 0.26
0040-BC 160.0 0.07 0050-BE 90.0 0.24
0060-BE 120.0 0.18
0075-BE 150.0 0.15
6.2 Reactor specification at DC side

DC inductance at input side
Model
Current (A) Inductance (mH)
R500-AC/BC 3.1 5.65
0001-AC/BC 4.5 3.89
0002-AC/BC 7.5 2.33
0003-AC/BC 10.5 1.67
0005-BC 17.5 1.00
7R50-BC 26 0.67
0010-BC 35 0.50
JNTHΧΧBA-
0001-BE 2.3 15.22
0002-BE 3.8 9.21
0003-BE 5.2 6.73
0005-BE 8.8 3.98
7R50-BE 13 2.69
0010-BE 17.5 2.00
0015-BE 25 1.40
6-1
6.3 Braking unit and braking resistor

7300CV series braking current calculation
Suitable Suitable Brake resistor
Braking Unit Brake Resistor Brake Brake
Inverter Motor Motor Specification Resistor dimension
resistor torque
Model Number Capacity Capacity (L*W*H) mm
Model Type (W) (Ω) ED(%) (%)
used (HP) (KW)
R500-AC/BC - - JNBR-150W200 0.5 0.4 150 200 10 238 251*28*60
0001-AC/BC - - JNBR-150W200 1 0.75 150 200 10 119 251*28*60
0002-AC/BC - - JNBR-150W100 2 1.5 150 100 10 119 251*28*60
0003-AC/BC - - JNBR-260W70 3 2.2 260 70 10 115 274*34*78
0005-BC - - JNBR-390W40 5 3.7 390 40 10 119 395*34*78
7R50-BC - - JNBR-520W30 7.5 5.5 520 30 10 108 400*40*100
0010-BC - - JNBR-780W20 10 7.5 780 20 10 119 400*40*100
0015-BC - - JNBR-2R4KW13R6 15 11 2400 13.6 10 117 535*50*110 (*2 pcs)
0020-BC - - JNBR-3KW10 20 15 3000 10 10 119 615*50*110 (*2 pcs)
0025-BC JNTBU-230 1 JNBR-4R8KW8 25 18.5 4800 8 10 119 535*50*110 (*4 pcs)
0030-BC JNTBU-230 1 JNBR-4R8KW6R8 30 22 4800 6.8 10 117 535*50*110 (*4 pcs)
0040-BC JNTBU-230 2 JNBR-3KW10 40 30 3000 10 10 119 615*50*110 (*2 pcs)
0001-BE - - JNBR-150W750 1 0.75 150 750 10 126 251*28*60
0002-BE - - JNBR-150W400 2 1.5 150 400 10 119 251*28*60
0003-BE - - JNBR-260W250- 3 2.2 260 250 10 126 274*34*78
0005-BE - - JNBR-400W150- 5 3.7 400 150 10 126 395*34*78
7R50-BE - - JNBR-600W130- 7.5 5.5 600 130 10 102 470*50*100
0010-BE - - JNBR-800W100 10 7.5 800 100 10 99 535*50*110
0015-BE - - JNBR-1R6KW50 15 11 1600 50 10 126 615*50*110
0020-BE - - JNBR-1R5KW40 20 15 1500 40 10 119 615*50*110
0025-BE JNTBU-430 1 JNBR-4R8KW32 25 18.5 4800 32 10 119 535*50*110 (*4 pcs)
0030-BE JNTBU-430 1 JNBR-4R8KW27R2 30 22 4800 27.2 10 117 535*50*110 (*4 pcs)
0040-BE JNTBU-430 1 JNBR-6KW20 40 30 6000 20 10 119 615*50*110 (*4 pcs)

*5
0050-BE JNVPHV-0060 1 JNBR-4R8KW32 50 37 4800 32 10 119 535*50*110 (*4 pcs)
0060-BE JNVPHV-0060 1*5 JNBR-4R8KW27R2 60 45 4800 27.2 10 117 535*50*110 (*4 pcs)
0075-BE JNTBU-430 2 JNBR-6KW20 75 55 6000 20 10 126 615*50*110 (*4 pcs)
Formula for brake resistor: W= ( Vpnb * Vpnb ) * ED% / Rmin

1. W : brake resistor consumption power
2. Vpnb: brake voltage (220V=380VDC, 440V=760VDC)
3. ED%: braking effective period
4. Rmin: allowable minimum brake resistor
5.Another choice: 0050-BE: (JNTBU-430 + JNBR-9R6KW32) × 2
0060-BE: (JNTBU-430 + JNBR-4R8KW27R2) × 2
Above 25HP, please add Braking Unit: 200V JNTBU-230
400V JNTBU-430
400V JUVPHV-0060
About the detail information, please contact with your supplier.
6-2
6.4 Digital operator and extension cable
A. Remote Cable Kit

Inverter Model Extension Cable Kit Cable Length (Meter)
JNSW-30P5 0.5
JNSW-3001 1.0
All models JNSW-3002 2.0
JNSW-3003 3.0
JNSW-3005 5.0
B. Content
c Inverter
d LED (JNSDOP-LED) or LCD (JNSDOP-LCD) Keypad
eREMOTE Cable for Keypad
C. Operation procedure:
Warning: Turn OFF the power supply. The following procedures should be performed after
there is no display on the keypad.
1. Remove the keypad from the Inverter.
2. Please refer to Diagram before mounting the keypad to your machine or Panel.
3. Connect the inverter and the keypad with the remote cable in accordance with the above
Diagram.
Supply the power to operate ONLY after all elements are securely fixed.
6-3
LED Keypad(JNSDOP-LED)Mounting Dimensions Unit： mm
LCD Keypad(JNSDOP-LCD)Mounting Dimensions Unit： mm
6-4
6. 5 EMC Filter
The inverter adopts rapid switching components to improve the efficiency of the motor and to
reduce the motor noise. Using the EMC Filter allows the EMI (Electromagnetic Interference) and
RFI (Radio Frequency interference) to be controlled within certain range.
EMC Directives
The inverter with optional filter complies with the EMC directives 89/336/EEC, limiting the
environmental EMI and RFI. Independent tests have demonstrated compliance to the following
standards when the optional filters are used.
EMI radio standard、EMS immunity standard
EN 61800-3 1996/A11: 2000：First Environment Unrestricted Distribution (Class B).
EN 61800-3 1996/A11: 2000：First Environment Restricted Distribution
Filter Selection
Filter Model
Inverter Model Rating (INPUT) First Environment First Environment
Restricted Distribution Unrestricted Distribution
R500AC-UF 1 φ 170 ~264V Built in FS 6146-11-07
0001AC-UF 1 φ 170~264V Built in FS 6146-11-07
0002AC-UF 1 φ 170~264V Built in FS 6146-27-07
0003AC-UF 1 φ 170 ~264V Built in FS 6146-27-07
R500AC-U 1 φ 170 ~264V FS 6146-11-07 --
0001AC-U 1 φ 170~264V FS 6146-11-07 --
0002AC-U 1 φ 170~264V FS 6146-27-07 --
0003AC-U 1 φ 170 ~264V FS 6146-27-07 --
R500BC-U 3 φ 170 ~264V FS 6147-8.9-07 --
0001BC-U 3 φ 170 ~264V FS 6147-8.9-07 --
0002BC-U 3 φ 170 ~264V FS 6147-8.9-07 --
0003BC-U 3 φ 170 ~264V FS 6147-19-07 --
0005BC-U 3 φ 170 ~264V FS 6147-19-07 --
7R50BC-U 3 φ 170 ~264V FS 6147-39-07 --
0010BC-U 3 φ 170 ~264V FS 6147-39-07 --
0001BE-UF 3 φ 323~528 V Built in FS 6149-4.6-07
0002BE-UF 3 φ 323~528 V Built in FS 6149-4.6-07
0003BE-UF 3 φ 323~528 V Built in FS 6149-10-07
JNTHBCBA
7R50BE-UF 3 φ 323~528 V Built in FS 6149-28-07
0001BE-U 3 φ 323~528 V FS 6149-4.6-07 --
0002BE-U 3 φ 323~528 V FS 6149-4.6-07 --
0003BE-U 3 φ 323~528 V FS 6149-10-07 --
0005BE-U 3 φ 323~528 V FS 6149-10-07 --
7R50BE-U 3 φ 323~528 V FS 6149-28-07 --
0010BE-U 3 φ 323~528 V FS 6149-28-07 --
0015BE-U 3 φ 323~528 V FS 6149-28-07 --
0020BE-U 3 φ 323~528 V JUNF34048S-MA --
0025BE-U 3 φ 323~528 V KMF370A --
0030BE-U 3 φ 323~528 V KMF370A --
0040BE-U 3 φ 323~528 V KMF3100A --
0050BE-U 3 φ 323~528 V KMF3100A --
0060BE-U 3 φ 323~528 V KMF3150A --
0075BE-U 3 φ 323~528 V KMF3180A --
6-5
7300CV External Filter Size
SIZE Inverter Mounting External Filter Size External Filter Mounting

MODEL Dimensions (C*B) (W*H*D) Dimensions(E*A)
FS 6146 - 11 - 07
FS 6147 - 8.9 - 07 78 * 150 91 * 192 * 28 74 * 181
FS 6149- 4.6 - 07
FS 6146 - 27 – 07
FS 6147 - 19 –07 114.6 * 170.5 128 * 215 * 37 111 * 204
FS 6149 - 10 - 07
FS 6147 - 39 – 07
FS 6149 - 28 - 07
173 * 244 188 * 289 * 42 165 * 278
Dimensions (mm)
Model
W W1 H H1 D d M
KMF370A 93 79 312 298 190 7 M6
KMF3100A 93 79 312 298 190 7 M6
JUNF34048S-MA KMF3150A 126 112 312 298 224 7 M6
KMF3180A 126 112 312 298 224 7 M6
250
225
L3
L3
LOAD
LINE
L2
100 50
L2
4 − φ 6.5
L1
L1
PE
PE
70
6-6
6.6 Interface Card
6.6.1 RS-485 Interface Card ( Model : JNSIF-485 )
JNSIF-485 Wiring Diagram：
Note:
Please put on the cover of inverter to avoid the Interface Card disturbed by outside
static electricity.
Please using isolated RS232 / RS485 converter to link PC and interface card to avoid damage
equipment.
6-7
6.6.2 RS-232 Interface Card (Model : JNSIF-232 )
JNSIF-232Wiring Diagram：
L1(L) T1
THREE-PHASE L2 T2
M
POWER SUPPLY L3(N) T3
7300CV
SERIES
RS-232 INVERTER
CON2 (12P)
JNSIF-232
1.8m
6-8
6.6.3 Program Copy Unit (Model: JNSIF-MP)
JNSIF-MP Wiring Diagram
L1(L) T1
THREE-PHASE
L2 T2 M
POWER SUPPLY
L3(N) T3
7300CV
SERIES
INVERTER
CON2 (12P)
JNSIF-MP
6.6.4 PDA Link
①. HP iPAQ Pocket PC h2210. (PDA)

②. PDA wire (JNSWPDA).
③. RS-232 Interface Card (JNSIF-232). 4
④. Inverter 3
1
55m
6-9
Appendix
Appendix 1: 7300CV Motor Internal Parameter List

Factory Setting of the Motor Internal Parameters：
Parameter 14-0 14-1 14-2 14-3 14-4

(Stator (Rotor (Equivalent (Magnetization (Iron Loss
Model Resistance) Resistance) Inductance) Current) Conductance)
R500AC/BC 200 200
0001AC/BC
380 300
0001BE
0002AC/BC
300 280
0002BE
0003AC/BC
280 240
0003BE
0005BC 7200 0
260 200
0005BE
7R50BC
240 160
7R50BE
0010BC
220 150
0010BE
JNTHBCBA 800
0015BC
200 140
0015BE
0020BC
0020BE
0025BC
0025BE
0030BC
0030BE 180 130 4100 205
0040BC
0040BE
0050BE
0060BE
0075BE
※Note：
1. The above motor internal parameters are idle under V/F Control Mode. These
parameters are usable under vector control mode.
App 1
Appendix
2. The motor parameters (14-0~14-4) are not be modified when factory setting
under vector mode. The internal parameters will be maintained at the ones
after auto tuning (refer to Auto Tuning and Description on motor Internal
Parameter).
3: The motor parameters (14-0~14-4) will be modified to factory setting
completely under whatever operation mode.
App 2
Appendix
Appendix 2: 7300CV parameter setting list

Customer Inverter Model
Using Site Contact Phone
Address
Parameter Setting Parameter Setting Content Parameter Setting Content Parameter Setting
Code Content Code Code Code Content
0-00 3-14 6-06 10-7
0-01 3-15 6-07 10-8
0-02 3-16 6-08 10-9
0-03 3-17 7-00 11-0
0-04 3-18 7-01 11-1
0-05 3-19 7-02 11-2
0-06 3-20 7-03 11-3
0-07 3-21 7-04 11-4
0-08 3-22 7-05 11-5
1-00 3-23 8-00 11-6
1-01 3-24 8-01 11-7
1-02 3-25 8-02 12-0
1-03 3-26 8-03 12-1
1-04 3-27 8-04 12-2
1-05 3-28 8-05 12-3
1-06 3-29 9-00 12-4
1-07 4-00 9-01 12-5
2-00 4-01 9-02 12-6
2-01 4-02 9-03 13-0
2-02 4-03 9-04 13-1
2-03 4-04 9-05 13-2
2-04 4-05 9-06 13-3
2-05 5-00 9-07 13-4
2-06 5-01 9-08 14-0
3-00 5-02 9-09 14-1
3-01 5-03 9-10 14-2
3-02 5-04 9-11 14-3
3-03 5-05 9-12 14-4
3-04 5-06 9-13 15-0
3-05 5-07 9-14 15-1
3-06 5-08 9-15 15-2
3-07 5-09 10-0 15-3
3-08 6-00 10-1 15-4
3-09 6-01 10-2 15-5
3-10 6-02 10-3 15-6
3-11 6-03 10-4
3-12 6-04 10-5
3-13 6-05 10-6
App 3

Inverter

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

Inverter

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Inverter

Uploaded by

Copyright:

Available Formats

User manual

Tel. (09189) 4147-0, Fax (09189) 4147-47

Step 1 Before Starting the Inverter

a. Verify that AC power is wired to L1, L2, and L3 (pages 3-12).

1. SEQ LED：1_00 =1, LED Lit.

Step 3 Check Motor Rotation Without Load

Step 4 Check Full Speed at 50Hz/60Hz

Step 5 Other Operations

AppendixⅡ 7300CV Parameters Setting List App2

Indicates a potential hazard could cause death or serious personal injury

Indicates that the inverter or the mechanical system might be damaged

0.2 Products Inspection

Chapter 1 Safety Precautions

1.1.2 During Power ON

1.1.3 Before Operation

1.1.4 During Operation

1.1.5 During Maintenance

Chapter 2 Definition of model

Inverter model → MODEL： JNTHBCBA0001AC-UF

Input voltage → I/P： AC 1 PH

Output specifications→ O/P： AC 3PH 0~264V

TECO ELECTRIC & MACHINERY CO., LTD.

Keypad Panel Horsepower： UL Approval：

BC：LED R500：0.5 HP U：Yes

AC：Single phase 220V

BC：Three phase 220V

Chapter 3 Ambient Environment and Installation

z Ambient temperature: -10oC ~ +40oC; without cover: -10oC ~ +50oC

Air exchanging fan Air exchanging fan

Inside the power Inside the

(Correct configuration) (Incorrect configuration) (Correct configuration) (Incorrect configuration)

Direct sunlight Corrosive gas and liquid Oil Mist

Wind, rain, and water

Strong vibration Extreme low temperature Excessive high temperature

Electromagnetic wave and

3.3 Inflammable materials

D. Nominal electrical specifications of the terminals Block:

This product is designed to use in Pollution Degree 2 environment or equivalent environments.

3.3.2 Applicable specification of magnetic contactor and wires

Signal terminals (TM2)

3.3.3 Precautions for peripheral applications:

z Add a noise filter or separation transformer whenter

MCCB Metal Box

To ground terminal Do not connect this end

(a) Good (b) Good (c) Bad

Control Mode V/F or Current Vector Control

Start control torque 150%/1Hz (Current Vector)

Speed control range 1:50 (Current Vector)

Speed Control Precision ±0.5% (Current Vector)

Setting resolution Digital: 0.01Hz( Note *1 ): Analog: 0.06Hz/ 60Hz(10bits)

Keypad setting Set directly with▲▼ keys or the VR on the keypad

V/F pattern 18-fixed patterns, 1 programmable pattern

Two-stage Acc/Dec time (0.1 – 3,600 seconds) and two-stage S

Multifunctional output 16 functions (refer to description on 8-02~8-03)

Digital Input Signal NPN (SINK) / PNP (SOURCE) toggle

Storage temperature -20 ~ 60℃

Humidity 0 – 95% Relative Humidity(Non-condense)

Height Below 1000M

13-2 (Comm Stop Bit) Stop Bit Selection 0000 23