MCT 10 Set-up Software

MCT 10 Set-up Software Project -- Untitled Tuesday, May 21, 2019

Group Folder: Project

Drive Name: 1; FC-101 0.75kW 220-240V

Connected Drive Information Database Information
Drive Series: FC-101 FC-101
Drive Type: 0.75kW 200-240V 0.75kW 220-240V
SW Version: 02.90 02.90
Option A No Option No Option
Option B No Option No Option
Option C0/E0 No Option No Option
Option C1/E1 No Option No Option
Drive Address: 1
Field-bus: Serial
Description

Parameter Group: All Parameters

ID Name Setup 1 Unit

001 Language Espanol
003 Regional Settings International
004 Operating State at Power-up Resume
006 GridType 200-240V/50Hz
007 Auto DC Braking On
010 Active Set-up Set-up 1
011 Programming Set-up Set-up 1
012 Link Setups Linked
030 Custom Readout Unit %
031 Custom Readout Min Value 0.00
032 Custom Readout Max Value 100.00
037 Display Text 1
038 Display Text 2
039 Display Text 3
040 [Hand on] Key on LCP Enabled
042 [Auto on] Key on LCP Enabled
044 [Off/Reset] Key on LCP Enabled
050 LCP Copy No copy
051 Set-up Copy No copy
060 Main Menu Password 0
061 Access to Main Menu w/o Password
Full access
100 Configuration Mode Process Closed Loop
101 Motor Control Principle VVC+
103 Torque Characteristics Variable Torque
106 Clockwise Direction Normal
108 Motor Control Bandwidth Medium
110 Motor Construction Asynchron
114 Damping Gain 120 %
115 Low Speed Filter Time Const.0.10 s
116 High Speed Filter Time Const.0.10 s
117 Voltage filter time const. 0.025 s
120 Motor Power 1.1 kW - 1.5 hp
122 Motor Voltage 230 V
123 Motor Frequency 50 Hz
124 Motor Current 4.87 A
125 Motor Nominal Speed 1420 rpm
126 Motor Cont. Rated Torque 219.5 Nm
129 Automatic Motor Adaption (AMA)
Off
130 Stator Resistance (Rs) 3.554 ohm
133 Stator Leakage Reactance (X1)2.238 ohm
135 Main Reactance (Xh) 38.20 ohm
137 d-axis Inductance (Ld) 7.300 mH

Page: 1 of 9
MCT 10 Set-up Software Project -- Untitled Tuesday, May 21, 2019

138 q-axis Inductance (Lq) 7.300 mH

139 Motor Poles 4
140 Back EMF at 1000 RPM 57 V
142 Motor Cable Length 5 m
143 Motor Cable Length Feet 16 ft
144 d-axis Inductance Sat. (LdSat)6.935 mH
145 q-axis Inductance Sat. (LqSat)6.935 mH
146 Position Detection Gain 100 %
148 Current at Min Inductance for 100
d-axis %
149 Current at Min Inductance for 100
q-axis %
150 Motor Magnetisation at Zero Speed
100 %
152 Min Speed Normal Magnetising 1.0[Hz] Hz
155.0 U/f Characteristic - U 0 V
155.1 U/f Characteristic - U 230 V
155.2 U/f Characteristic - U 230 V
155.3 U/f Characteristic - U 230 V
155.4 U/f Characteristic - U 230 V
155.5 U/f Characteristic - U 230 V
156.0 U/f Characteristic - F 0 Hz
156.1 U/f Characteristic - F 50 Hz
156.2 U/f Characteristic - F 50 Hz
156.3 U/f Characteristic - F 50 Hz
156.4 U/f Characteristic - F 50 Hz
156.5 U/f Characteristic - F 50 Hz
162 Slip Compensation 0 %
163 Slip Compensation Time Constant
0.10 s
164 Resonance Dampening 100 %
165 Resonance Dampening Time Constant
0.005 s
166 Min. Current at Low Speed 50 %
170 PM Start Mode Parking
171 Start Delay 0.0 s
172 Start Function Coast/delay time
173 Flying Start Disabled
180 Function at Stop Coast
182 Min Speed for Function at Stop0.0[Hz] Hz
188 AC Brake Gain 1.4
190 Motor Thermal Protection ETR trip 1
193 Thermistor Source None
200 DC Hold/Motor Preheat Current 50 %
201 DC Brake Current 50 %
202 DC Braking Time 10.0 s
204 DC Brake Cut In Speed 0.0 Hz
206 Parking Current 100 %
207 Parking Time 3.0 s
210 Brake Function Off
216 AC Brake, Max current 100 %
217 Over-voltage Control Enabled
302 Minimum Reference 0.000
303 Maximum Reference 50.000
310.0 Preset Reference 0.00 %
310.1 Preset Reference 0.00 %
310.2 Preset Reference 0.00 %
310.3 Preset Reference 0.00 %
310.4 Preset Reference 0.00 %
310.5 Preset Reference 0.00 %
310.6 Preset Reference 0.00 %
310.7 Preset Reference 0.00 %
311 Jog Speed [Hz] 5.0 Hz
314 Preset Relative Reference 0.00 %
315 Reference 1 Source No function
316 Reference 2 Source No function
317 Reference 3 Source Local bus reference
341 Ramp 1 Ramp Up Time 1.00 s
342 Ramp 1 Ramp Down Time 10.40 s

Page: 2 of 9
MCT 10 Set-up Software Project -- Untitled Tuesday, May 21, 2019

351 Ramp 2 Ramp Up Time 10.00 s

352 Ramp 2 Ramp Down Time 10.00 s
380 Jog Ramp Time 10.00 s
381 Quick Stop Ramp Time 10.00 s
410 Motor Speed Direction Both directions
412 Motor Speed Low Limit [Hz] 0.0 Hz
414 Motor Speed High Limit [Hz] 60.0 Hz
418 Current Limit 90 %
419 Max Output Frequency 60.0 Hz
440 Warning Freq. Low 0.0 Hz
441 Warning Freq. High 60.0 Hz
450 Warning Current Low 0.00 A
451 Warning Current High 4.91 A
454 Warning Reference Low -4,999.000
455 Warning Reference High 4,999.000
456 Warning Feedback Low -4,999.000
457 Warning Feedback High 4,999.000
458 Missing Motor Phase FunctionOn
461.0 Bypass Speed From [Hz] 0.0 Hz
461.1 Bypass Speed From [Hz] 0.0 Hz
461.2 Bypass Speed From [Hz] 0.0 Hz
463.0 Bypass Speed To [Hz] 0.0 Hz
463.1 Bypass Speed To [Hz] 0.0 Hz
463.2 Bypass Speed To [Hz] 0.0 Hz
464 Semi-Auto Bypass Set-up Off
500 Digital Input Mode PNP
503 Digital Input 29 Mode PNP
510 Terminal 18 Digital Input Start
511 Terminal 19 Digital Input No operation
512 Terminal 27 Digital Input No operation
513 Terminal 29 Digital Input No operation
534 On Delay, Digital Output 0.01 s
535 Off Delay, Digital Output 0.01 s
540.0 Function Relay Alarm
540.1 Function Relay Drive running
541.0 On Delay, Relay 0.01 s
541.1 On Delay, Relay 0.01 s
542.0 Off Delay, Relay 0.01 s
542.1 Off Delay, Relay 0.01 s
550 Term. 29 Low Frequency 20 Hz
551 Term. 29 High Frequency 32000 Hz
552 Term. 29 Low Ref./Feedb. Value
0.000
553 Term. 29 High Ref./Feedb. Value
50.000
590 Digital & Relay Bus Control 0hex
600 Live Zero Timeout Time 10 s
601 Live Zero Timeout Function Off
602 Fire Mode Live Zero Timeout Off
Function
610 Terminal 53 Low Voltage 0.07 V
611 Terminal 53 High Voltage 10.00 V
612 Terminal 53 Low Current 4.00 mA
613 Terminal 53 High Current 20.00 mA
614 Terminal 53 Low Ref./Feedb. Value
0.000
615 Terminal 53 High Ref./Feedb. 50.000
Value
616 Terminal 53 Filter Time Constant
0.01 s
619 Terminal 53 mode Current mode
620 Terminal 54 Low Voltage 0.00 V
621 Terminal 54 High Voltage 10.00 V
622 Terminal 54 Low Current 4.00 mA
623 Terminal 54 High Current 20.00 mA
624 Terminal 54 Low Ref./Feedb. Value
0.000
625 Terminal 54 High Ref./Feedb. 100.000
Value
626 Terminal 54 Filter Time Constant
1.00 s
629 Terminal 54 mode Current mode
670 Terminal 45 Mode 0-20 mA

Page: 3 of 9
MCT 10 Set-up Software Project -- Untitled Tuesday, May 21, 2019

671 Terminal 45 Analog Output No operation

672 Terminal 45 Digital Output No operation
673 Terminal 45 Output Min Scale0.00 %
674 Terminal 45 Output Max Scale100.00 %
676 Terminal 45 Output Bus Control
0
690 Terminal 42 Mode 0-20 mA
691 Terminal 42 Analog Output No operation
692 Terminal 42 Digital Output No operation
693 Terminal 42 Output Min Scale0.00 %
694 Terminal 42 Output Max Scale100.00 %
696 Terminal 42 Output Bus Control
0
801 Control Site Digital and ctrl.word
802 Control Source FC Port
803 Control Timeout Time 1.0 s
804 Control Timeout Function Off
831 Address 1
832 Baud Rate 9600 Baud
833 Parity / Stop Bits Even Parity, 1 Stop Bit
835 Minimum Response Delay 0.010 s
836 Maximum Response Delay 5.000 s
837 Maximum Inter-char delay 0.025 s
842.0 PCD Write Configuration FC Port CTW
842.1 PCD Write Configuration FC Port REF
842.2 PCD Write Configuration None
842.3 PCD Write Configuration None
842.4 PCD Write Configuration None
842.5 PCD Write Configuration None
842.6 PCD Write Configuration None
842.7 PCD Write Configuration None
842.8 PCD Write Configuration None
842.9 PCD Write Configuration None
842.10 PCD Write Configuration None
842.11 PCD Write Configuration None
842.12 PCD Write Configuration None
842.13 PCD Write Configuration None
842.14 PCD Write Configuration None
842.15 PCD Write Configuration None
843.0 PCD Read Configuration [1603] Status Word
843.1 PCD Read Configuration [1605] Main Actual Value [%]
843.2 PCD Read Configuration None
843.3 PCD Read Configuration None
843.4 PCD Read Configuration None
843.5 PCD Read Configuration None
843.6 PCD Read Configuration None
843.7 PCD Read Configuration None
843.8 PCD Read Configuration None
843.9 PCD Read Configuration None
843.10 PCD Read Configuration None
843.11 PCD Read Configuration None
843.12 PCD Read Configuration None
843.13 PCD Read Configuration None
843.14 PCD Read Configuration None
843.15 PCD Read Configuration None
850 Coasting Select Logic OR
851 Quick Stop Select Logic OR
852 DC Brake Select Logic OR
853 Start Select Logic OR
854 Reversing Select Digital input
855 Set-up Select Logic OR
856 Preset Reference Select Logic OR
870 BACnet Device Instance 1
872 MS/TP Max Masters 127
873 MS/TP Max Info Frames 1
874 "I am Service Send at power-up

Page: 4 of 9
MCT 10 Set-up Software Project -- Untitled Tuesday, May 21, 2019

875 Intialisation Password admin

879.0 Protocol Firmware version 0.00
879.1 Protocol Firmware version 0.00
879.2 Protocol Firmware version 0.00
879.3 Protocol Firmware version 1.00
879.4 Protocol Firmware version 3.00
880 Bus Message Count 1334
881 Bus Error Count 0
882 Slave Messages Rcvd 1332
883 Slave Error Count 0
884 Slave Messages Sent 0
885 Slave Timeout Errors 0
888 Reset FC port Diagnostics Do not reset
894 Bus Feedback 1 0
895 Bus Feedback 2 0
1300 SL Controller Mode Off
1301 Start Event Start command
1302 Stop Event Drive stopped
1303 Reset SLC Do not reset SLC
1310.0 Comparator Operand Disabled
1310.1 Comparator Operand Disabled
1310.2 Comparator Operand Disabled
1310.3 Comparator Operand Disabled
1310.4 Comparator Operand Disabled
1310.5 Comparator Operand Disabled
1311.0 Comparator Operator Approx.Equal (~)
1311.1 Comparator Operator Approx.Equal (~)
1311.2 Comparator Operator Approx.Equal (~)
1311.3 Comparator Operator Approx.Equal (~)
1311.4 Comparator Operator Approx.Equal (~)
1311.5 Comparator Operator Approx.Equal (~)
1312.0 Comparator Value 0.000
1312.1 Comparator Value 0.000
1312.2 Comparator Value 0.000
1312.3 Comparator Value 0.000
1312.4 Comparator Value 0.000
1312.5 Comparator Value 0.000
1320.0 SL Controller Timer 0.00 s
1320.1 SL Controller Timer 0.00 s
1320.2 SL Controller Timer 0.00 s
1320.3 SL Controller Timer 0.00 s
1320.4 SL Controller Timer 0.00 s
1320.5 SL Controller Timer 0.00 s
1320.6 SL Controller Timer 0.00 s
1320.7 SL Controller Timer 0.00 s
1340.0 Logic Rule Boolean 1 False
1340.1 Logic Rule Boolean 1 False
1340.2 Logic Rule Boolean 1 False
1340.3 Logic Rule Boolean 1 False
1340.4 Logic Rule Boolean 1 False
1340.5 Logic Rule Boolean 1 False
1341.0 Logic Rule Operator 1 Disabled
1341.1 Logic Rule Operator 1 Disabled
1341.2 Logic Rule Operator 1 Disabled
1341.3 Logic Rule Operator 1 Disabled
1341.4 Logic Rule Operator 1 Disabled
1341.5 Logic Rule Operator 1 Disabled
1342.0 Logic Rule Boolean 2 False
1342.1 Logic Rule Boolean 2 False
1342.2 Logic Rule Boolean 2 False
1342.3 Logic Rule Boolean 2 False
1342.4 Logic Rule Boolean 2 False
1342.5 Logic Rule Boolean 2 False
1343.0 Logic Rule Operator 2 Disabled

Page: 5 of 9
MCT 10 Set-up Software Project -- Untitled Tuesday, May 21, 2019

1343.1 Logic Rule Operator 2 Disabled

1343.2 Logic Rule Operator 2 Disabled
1343.3 Logic Rule Operator 2 Disabled
1343.4 Logic Rule Operator 2 Disabled
1343.5 Logic Rule Operator 2 Disabled
1344.0 Logic Rule Boolean 3 False
1344.1 Logic Rule Boolean 3 False
1344.2 Logic Rule Boolean 3 False
1344.3 Logic Rule Boolean 3 False
1344.4 Logic Rule Boolean 3 False
1344.5 Logic Rule Boolean 3 False
1351.0 SL Controller Event False
1351.1 SL Controller Event False
1351.2 SL Controller Event False
1351.3 SL Controller Event False
1351.4 SL Controller Event False
1351.5 SL Controller Event False
1351.6 SL Controller Event False
1351.7 SL Controller Event False
1351.8 SL Controller Event False
1351.9 SL Controller Event False
1351.10 SL Controller Event False
1351.11 SL Controller Event False
1351.12 SL Controller Event False
1351.13 SL Controller Event False
1351.14 SL Controller Event False
1351.15 SL Controller Event False
1351.16 SL Controller Event False
1351.17 SL Controller Event False
1351.18 SL Controller Event False
1351.19 SL Controller Event False
1352.0 SL Controller Action Disabled
1352.1 SL Controller Action Disabled
1352.2 SL Controller Action Disabled
1352.3 SL Controller Action Disabled
1352.4 SL Controller Action Disabled
1352.5 SL Controller Action Disabled
1352.6 SL Controller Action Disabled
1352.7 SL Controller Action Disabled
1352.8 SL Controller Action Disabled
1352.9 SL Controller Action Disabled
1352.10 SL Controller Action Disabled
1352.11 SL Controller Action Disabled
1352.12 SL Controller Action Disabled
1352.13 SL Controller Action Disabled
1352.14 SL Controller Action Disabled
1352.15 SL Controller Action Disabled
1352.16 SL Controller Action Disabled
1352.17 SL Controller Action Disabled
1352.18 SL Controller Action Disabled
1352.19 SL Controller Action Disabled
1401 Switching Frequency 5.0 kHz
1403 Overmodulation Off
1407 Dead Time Compensation Level100
1408 Damping Gain Factor 96 %
1409 Dead Time Bias Current Level0 %
1410 Mains Failure No function
1411 Mains Fault Voltage Level 180 V
1412 Response to Mains ImbalanceTrip
1420 Reset Mode Manual reset
1421 Automatic Restart Time 10 s
1422 Operation Mode Normal operation
1427 Action At Inverter Fault Warning
1429 Service Code 0

Page: 6 of 9
MCT 10 Set-up Software Project -- Untitled Tuesday, May 21, 2019

1430 Current Lim Ctrl, Proportional100

Gain %
1431 Current Lim Ctrl, Integration Time
0.020 s
1432 Current Lim Ctrl, Filter Time 26.0 ms
1440 VT Level 90 %
1441 AEO Minimum Magnetisation66 %
1444 d-axis current optimization for100
IPM %
1450 RFI Filter On
1451 DC-Link Voltage Compensation On
1452 Fan Control Auto
1453 Fan Monitor Warning
1455 Output Filter No Filter
1461 Function at Inverter Overload Trip
1463 Min Switch Frequency 2.0 kHz
1464 Dead Time Compensation ZeroDisabled
Current Level
1465 Speed Derate Dead Time Compensation
500 Hz
1490.0 Fault Level Trip lock
1490.1 Fault Level Trip lock
1490.2 Fault Level Trip lock
1490.3 Fault Level Trip lock
1490.4 Fault Level Trip lock
1490.5 Fault Level Trip lock
1490.6 Fault Level Trip lock
1490.7 Fault Level Trip lock
1500 Operating hours 18 h
1501 Running Hours 2 h
1502 kWh Counter 0 kWh
1503 Power Up's 55
1504 Over Temp's 0
1505 Over Volt's 0
1506 Reset kWh Counter Do not reset
1507 Reset Running Hours CounterDo not reset
1530.0 Alarm Log: Error Code 80
1530.1 Alarm Log: Error Code 80
1530.2 Alarm Log: Error Code 9
1530.3 Alarm Log: Error Code 53
1530.4 Alarm Log: Error Code 53
1530.5 Alarm Log: Error Code 32
1530.6 Alarm Log: Error Code 56
1530.7 Alarm Log: Error Code 56
1530.8 Alarm Log: Error Code 60
1530.9 Alarm Log: Error Code 47
1531 InternalFaultReason 0
1540 FC Type FC-101
1541 Power Section PK75: 0.75kW
1542 Voltage T2: 3x200-240VAC
1543 Software Version 2.90
1544 Ordered TypeCode FC-101PK75T2E20H4XXCXXXSXXXXAXBXCXXXXDX
1545 Actual Typecode String FC-101PK75T2E20H4XXCXXXSXXXXAXBXCXXXXDX
1546 Drive Ordering No 131L9794
1548 LCP Id No LCP 132b0200 v11.00
1549 SW ID Control Card A:2081 M:2041 D:0251
1550 SW ID Power Card SW:2041 EE:0139
1551 Drive Serial Number 091214A267
1553 Power Card Serial Number 132B6543 003250L177
1559 Filename
1600 Control Word 43Chex
1601 Reference [Unit] 0.000
1602 Reference [%] 0.0 %
1603 Status Word 7hex
1605 Main Actual Value [%] 0.00 %
1609 Custom Readout 0.00
1610 Power [kW] 0.000 kW
1611 Power [hp] 0.000 hp
1612 Motor Voltage 0 V

Page: 7 of 9
MCT 10 Set-up Software Project -- Untitled Tuesday, May 21, 2019

1613 Frequency 0.0 Hz

1614 Motor current 0.00 A
1615 Frequency [%] 0.0 %
1616 Torque [Nm] 0.0 Nm
1617 Speed [RPM] 0 rpm
1618 Motor Thermal 0 %
1622 Torque [%] 0 %
1630 DC Link Voltage 303 V
1634 Heatsink Temp. 18 °C
1635 Inverter Thermal 0 %
1636 Inv. Nom. Current 4.20 A
1637 Inv. Max. Current 4.91 A
1638 SL Controller State 0
1650 External Reference 0.0 %
1652 Feedback[Unit] -25.000
1654 Feedback 1 [Unit] -12.500
1655 Feedback 2 [Unit] -12.500
1660 Digital Input 0000000000000000bin
1661 Terminal 53 Setting Current mode
1662 Analog input 53 0.00
1663 Terminal 54 Setting Current mode
1664 Analog input 54 0.00
1665 Analog output 42 [mA] 0.00 mA
1666 Digital Output XX
1667 Pulse input 29[Hz] 0
1671 Relay output 0hex
1672 Counter A 0
1673 Counter B 0
1679 Analog output 45 [mA] 0.00 mA
1686 FC Port REF 1 0
1690 Alarm Word 0hex
1691 Alarm Word 2 0hex
1692 Warning Word 0hex
1693 Warning Word 2 0hex
1694 Ext. Status Word 0hex
1695 Ext. Status Word 2 983hex
1810.0 FireMode Log:Event 0
1810.1 FireMode Log:Event 0
1810.2 FireMode Log:Event 0
1810.3 FireMode Log:Event 0
1810.4 FireMode Log:Event 0
1810.5 FireMode Log:Event 0
1810.6 FireMode Log:Event 0
1810.7 FireMode Log:Event 0
1810.8 FireMode Log:Event 0
1810.9 FireMode Log:Event 0
2000 Feedback 1 Source Analog Input 53
2001 Feedback 1 Conversion Linear
2003 Feedback 2 Source Analog Input 53
2004 Feedback 2 Conversion Linear
2020 Feedback Function Sum
2081 PI Normal/ Inverse Control Inverse
2083 PI Start Speed [Hz] 0.0 Hz
2084 On Reference Bandwidth 0 %
2091 PI Anti Windup On
2093 PI Proportional Gain 1.17
2094 PI Integral Time 2.23 s
2097 PI Feed Forward Factor 100 %
2201 Power Filter Time 0.50 s
2202 Sleepmode CL Control Mode Normal
2223 No-Flow Function Off
2224 No-Flow Delay 10 s
2230 No-Flow Power 0.00 kW
2231 Power Correction Factor 100 %

Page: 8 of 9
MCT 10 Set-up Software Project -- Untitled Tuesday, May 21, 2019

2233 Low Speed [Hz] 0.0 Hz

2234 Low Speed Power [kW] 0.00 kW
2237 High Speed [Hz] 0.0 Hz
2238 High Speed Power [kW] 0.00 kW
2240 Minimum Run Time 10 s
2241 Minimum Sleep Time 10 s
2243 Wake-Up Speed [Hz] 10.0
2244 Wake-Up Ref./FB Diff 10 %
2245 Setpoint Boost 0 %
2246 Maximum Boost Time 60 s
2247 Sleep Speed [Hz] 0.0
2248 Sleep Delay Time 0 s
2249 Wake-Up Delay Time 0 s
2260 Broken Belt Function Off
2261 Broken Belt Torque 10 %
2262 Broken Belt Delay 10 s
2280 Flow Compensation Disabled
2281 Square-linear Curve Approximation
100 %
2282 Work Point Calculation Disabled
2284 Speed at No-Flow [Hz] 50.0 Hz
2286 Speed at Design Point [Hz] 50.0 Hz
2287 Pressure at No-Flow Speed 0.000
2288 Pressure at Rated Speed 4,999.000
2289 Flow at Design Point 0.000
2290 Flow at Rated Speed 0.000
2400 FM Function Disabled
2401 Fire Mode Configuration Open Loop
2405 FM Preset Reference 0 %
2406 Fire Mode Reference Source No function
2407 Fire Mode Feedback Source No function
2409 FM Alarm Handling Trip, Crit.Alarms
2410 Drive Bypass Function Disabled
2411 Drive Bypass Delay Time 0 s
3022 Locked Rotor Protection Off
3023 Locked Rotor Detection Time 0.10
[s] s

Page: 9 of 9