Sew Motor Maintenance

Drive Technology \ Drive Automation \ System Integration \ Services
Assembly and Operating Instructions
Explosion-Proof Gear Units

R..7, F..7, K..7, S..7, SPIROPLAN® W Series
Edition 09/2012 20050542 / EN

SEW-EURODRIVE—Driving the world
Contents
Contents
1 General Information ............................................................................................ 6
1.1 How to use this documentation................................................................... 6
1.2 Structure of the safety notes ....................................................................... 6
1.3 Rights to claim under warranty ................................................................... 7
1.4 Exclusion of liability..................................................................................... 7
1.5 Copyright..................................................................................................... 7
1.6 Product names and trademarks.................................................................. 7
2 Safety Notes ........................................................................................................ 8
2.1 Preliminary information ............................................................................... 8
2.2 General information .................................................................................... 8
2.3 Target group ............................................................................................... 9
2.4 Designated use ........................................................................................... 9
2.5 Other applicable documentation ............................................................... 10
2.6 Transport/storage...................................................................................... 10
2.7 Installation/assembly................................................................................. 10
2.8 Startup/operation ...................................................................................... 10
2.9 Inspection/maintenance ............................................................................ 10
3 Check Lists ........................................................................................................ 11
3.1 Before startup ........................................................................................... 11
3.2 During startup ........................................................................................... 12
4 Gear Unit Structure ........................................................................................... 13
4.1 Basic design of helical gear units.............................................................. 13
4.2 Basic structure of parallel shaft helical gear units ..................................... 14
4.3 Basic structure of helical-bevel gear units ................................................ 15
4.4 Basic design of helical-worm gear units.................................................... 16
4.5 Basic design of SPIROPLAN® W10-W30 gear units ................................ 17
4.6 Basic design of SPIROPLAN® W37 gear units......................................... 18
4.7 Nameplate and type designation .............................................................. 19
5 Mechanical Installation ..................................................................................... 21
5.1 Required tools/resources .......................................................................... 21
5.2 Installation requirements........................................................................... 22
5.3 Installing the gear unit............................................................................... 23
5.4 Gear unit with solid shaft........................................................................... 31
5.5 Gear units and gearmotors in category II2GD .......................................... 34
5.6 Torque arms for shaft-mounted gear units................................................ 36
5.7 Shaft-mounted gear units with keyway or splined hollow shaft................. 39
5.8 Shaft-mounted gear units with shrink disk ................................................ 46
5.9 Shaft-mounted gear units with TorqLOC® ................................................ 50
5.10 Installing the cover .................................................................................... 57
5.11 Coupling of AM adapter ............................................................................ 59
5.12 Coupling of AQ adapter ............................................................................ 63
5.13 Adapter with a torque limiting coupling AR ............................................... 65
5.14 AD input shaft assembly ........................................................................... 67
Assembly and Operating Instructions – Explosion-Proof Gear Units 3

Contents
6 Startup................................................................................................................ 73
6.1 Checking the oil level ................................................................................ 74
6.2 Measuring the surface and oil temperature .............................................. 75
6.3 Pseudo-leakage at shaft seals.................................................................. 76
6.4 Helical-worm and SPIROPLAN® W gear units ......................................... 76
6.5 Helical/parallel shaft helical/helical-bevel gear units ................................. 77
6.6 Gear units with backstop........................................................................... 77
6.7 Speed monitoring...................................................................................... 78
6.8 Installation and adjustment of the WEX speed monitor ............................ 78
6.9 Installation of the voltage encoder ............................................................ 82
7 Inspection/Maintenance ................................................................................... 84
7.1 Preliminary work regarding gear unit inspection/maintenance ................. 84
7.2 Inspection/maintenance intervals.............................................................. 86
7.3 Lubricant change intervals ........................................................................ 86
7.4 Inspection/maintenance for the AL / AM / AQ. / EWH adapter ................. 87
7.5 AR adapter................................................................................................ 87
7.6 Inspection/maintenance for the AD input shaft assembly ......................... 91
7.7 Inspection/maintenance for the gear unit.................................................. 92
8 Mounting Positions ......................................................................................... 109
8.1 Designation of the mounting positions .................................................... 109
8.2 Churning losses ...................................................................................... 110
8.3 Mounting positions of SPIROPLAN® gear units...................................... 110
8.4 Key.......................................................................................................... 110
8.5 Helical gearmotors R .............................................................................. 111
8.6 Helical gearmotors RX ............................................................................ 114
8.7 Parallel-shaft helical gearmotors F ......................................................... 116
8.8 Helical-bevel gearmotors K..................................................................... 119
8.9 Helical-worm gearmotors S..................................................................... 124
8.10 SPIROPLAN® W gearmotors.................................................................. 130
9 Technical Data ................................................................................................. 136
9.1 Extended storage.................................................................................... 136
9.2 Lubricants ............................................................................................... 137
10 Malfunctions .................................................................................................... 141
10.1 Gear unit ................................................................................................. 142
10.2 AM / AQ. / AL / EWH adapter ................................................................. 143
10.3 AD input shaft assembly ......................................................................... 143
10.4 Adapter with a torque limiting coupling AR ............................................. 143
10.5 Customer service .................................................................................... 144
10.6 Disposal .................................................................................................. 144
4 Assembly and Operating Instructions – Explosion-Proof Gear Units

Contents
11 Declarations of Conformity ............................................................................ 145

11.1 Gear units in category 2G and 2D with AM / AQA / AL / AD / AR adapter.. 145
11.2 Gear units in category 3G and 3D with AR adapter............................... 146
12 Address List .................................................................................................... 148
Index................................................................................................................. 160

General Information
1 How to use this documentation
1 General Information
1.1 How to use this documentation
The documentation is an integral part of the product and contains important information
on operation and service. The documentation is written for all employees who assemble,
install, startup, and service this product.
The documentation must be accessible and legible. Make sure that persons responsible
for the system and its operation, as well as persons who work independently on the unit,
have read through the documentation carefully and understood it. If you are unclear
about any of the information in this documentation, or if you require further information,
contact SEW-EURODRIVE.
1.2 Structure of the safety notes

1.2.1 Meaning of the signal words
The following table shows the grading and meaning of the signal words for safety notes,
notes on potential risks of damage to property, and other notes.
Signal word Meaning Consequences if disregarded
DANGER Imminent danger Severe or fatal injuries
WARNING Possible dangerous situation Severe or fatal injuries
CAUTION Possible dangerous situation Minor injuries
NOTICE Possible damage to property Damage to the drive system or its
environment
NOTE ON Important note on explosion Suspension of explosion protection and
EXPLOSION protection resulting hazards
PROTECTION
INFORMATION Useful information or tip:
Simplifies the handling of the
drive system.
1.2.2 Structure of the section-related safety notes

Section-related safety notes do not apply to a specific action, but to several actions per-
taining to one subject. The used symbols indicate either a general or a specific hazard.
This is the formal structure of a section-related safety note:
SIGNAL WORD
Nature and source of danger.
Possible consequence(s) if disregarded.
• Measure(s) to avoid the danger.
1.2.3 Structure of the embedded safety notes

Embedded safety notes are directly integrated in the instructions just before the descrip-
tion of the dangerous action.
This is the formal structure of an embedded safety note:
• SIGNAL WORD Nature and source of danger.
Possible consequence(s) if disregarded.
– Measure(s) to avoid the danger.

General Information
Rights to claim under warranty
1
1.3 Rights to claim under warranty

A requirement of fault-free operation and fulfillment of any rights to claim under limited
warranty is that you adhere to the information in the documentation. Read the documen-
tation before you start working with the unit!
1.4 Exclusion of liability

You must comply with the information contained in this documentation to ensure safe
operation of the Explosion-proof gear unit series R..7, F..7, K..7, S..7, SPIROPLAN® W
units and to achieve the specified product characteristics and performance require-
ments. SEW-EURODRIVE assumes no liability for injury to persons or damage to equip-
ment or property resulting from non-observance of the documentation. In such cases,
any liability for defects is excluded.
1.5 Copyright
© 2012 - SEW-EURODRIVE. All rights reserved.
Copyright law prohibits the unauthorized duplication, modification, distribution, and use
of this document, in whole or in part.
1.6 Product names and trademarks

The brands and product names contained within this publication are trademarks or
registered trademarks of the titleholders.

Safety Notes
2 Preliminary information
2 Safety Notes
The following basic safety notes must be read carefully to prevent injury to persons and
damage to property. The operator must ensure that the basic safety notes are read and
adhered to. Make sure that persons responsible for the system and its operation, as well
as persons who work independently on the unit, have read through the operating instruc-
tions carefully and understood them. If you are unclear about any of the information in
this documentation or if you require further information, please contact SEW-
EURODRIVE.
2.1 Preliminary information

The following safety notes are primarily concerned with the use of the following compo-
nents: Explosion-proof gear unit series R..7, F..7, K..7, S..7, SPIROPLAN® W. If using
gearmotors, please also refer to the safety notes in the corresponding operating instruc-
tions for:
• Gear unit
Also observe the supplementary safety notes in the individual sections of this documen-
tation.
2.2 General information
WARNING
During operation, the motors and gearmotors can have live, bare (in the event of open
connectors/terminal boxes) and movable or rotating parts as well as hot surfaces, de-
pending on their enclosure.
Severe or fatal injuries.
• All work related to transportation, storage, installation, assembly, connection,
startup, maintenance and repair may only be carried out by qualified personnel, in
strict observance of:
– The relevant detailed operating instructions
– The warning and safety signs on the motor/gearmotor
– All other project planning documents, operating instructions and wiring dia-
grams related to the drive
– The specific regulations and requirements for the system
– The national/regional regulations governing safety and the prevention of acci-
dents
• Never install damaged products
• Immediately report any damage to the shipping company
Removing the required protection cover or the housing without authorization, improper
use as well as incorrect installation or operation may result in severe injuries to persons
or damage to property.
This documentation provides additional information.

Safety Notes
Target group
2
2.3 Target group

Any mechanical work may only be performed by adequately qualified personnel. Quali-
fied staff in the context of this documentation are persons familiar with the design, me-
chanical installation, troubleshooting and servicing of the product who possess the fol-
lowing qualifications:
• Training in mechanical engineering, e.g. as a mechanic or mechatronics technician
(final examinations must have been passed).
• They are familiar with these operating instructions.
Any electronic work may only be performed by adequately qualified electricians. Quali-
fied electricians in the context of this documentation are persons familiar with electrical
installation, startup, troubleshooting and servicing of the product who possess the fol-
lowing qualifications:
• Training in electrical engineering, e.g. as an electrician, electronics or mechatronics
technician (final examinations must have been passed).
• They are familiar with these operating instructions.
All work in further areas of transportation, storage, operation and waste disposal must
only be carried out by persons who are trained appropriately.
All qualified personnel must wear appropriate protective clothing.
2.4 Designated use

The gear units are intended for industrial systems and may only be used in accordance
with the information provided in SEW-EURODRIVE's technical documentation and the
information given on the nameplate. They meet the requirements set forth in Directive
94/9/EC and comply with the applicable standards and regulations.
The gear units are components for the installation in machines and plants according to
the 2006/42/EC Machinery Directive. Within the scope of the Directive, you must not op-
erate the machine in the designated fashion until you have established that the end
product complies with Machinery Directive 2006/42/EC.
NOTE ON EXPLOSION PROTECTION

A drive motor connected to the gear unit is only allowed to be operated under the con-
ditions described in chapter "Mechanical Installation / Gear units and gearmotors in
category II2GD" (page 34).
A motor mounted to the gear unit may only be operated on a frequency inverter if the
data on the gear unit nameplate is met!
If a gear unit is operated in combination with a variable speed gear unit, the operating
instructions of the variable speed gear unit must be observed in addition.
A motor mounted to a gear unit by means of an adapter or belt may only be operated
if the data on the gear unit nameplate is met!
Make sure that there are no aggressive substances in the vicinity that could damage
the paint and seals.

Safety Notes
2 Other applicable documentation
2.5 Other applicable documentation

2.5.1 Explosion-proof gear units
The following publications and documents have to be observed as well:
• "Explosion-Proof AC Motors DR.71 – 225" operating instructions
• Operating instructions of any attached options
• "Explosion-Proof AC Motors" catalog and, if applicable,
• "Explosion-proof drives" catalog
2.6 Transport/storage
Inspect the shipment for any damage that may have occurred in transit as soon as you
receive the delivery. Inform the shipping company immediately. It may be necessary to
preclude startup.
Tighten the eyebolts securely. They are designed to only carry the weight of the mo-
tor/gearmotor; do not attach any additional loads.
The built-in lifting eyebolts comply with DIN 580. Always observe the loads and regula-
tions listed in this standard. If the gearmotor is equipped with two eyebolts, then both
should be used for transportation. In this case, the tension force vector of the slings must
not exceed a 45° angle according to DIN 580.
Use suitable, sufficiently rated handling equipment if required. Reattach these in the
case of further transportation.
Store the motor/gearmotor in a dry, dust-free environment if it is not to be installed
straight away. You must not store the motor/gearmotor outdoors or on the fan guard.
The motor/gearmotor can be stored for up to 9 months without requiring any special
measures before startup.
2.7 Installation/assembly
Observe the notes in section "Mechanical Installation" (page 21)!
2.8 Startup/operation
Check the oil level before startup as described in chapter Inspection/Maintenance
(page 84).
Check that the direction of rotation is correct in decoupled status. Listen out for unusual
grinding noises as the shaft rotates.
Secure keys for test mode without output elements. Do not deactivate monitoring and
protection equipment even in test mode.
Switch off the gearmotor if in doubt whenever changes occur in relation to normal oper-
ation (e.g. increased temperature, noise, vibration). Determine the cause and contact
SEW-EURODRIVE, if required.
2.9 Inspection/maintenance
Observe the notes in chapter "Inspection/Maintenance" (page 84).

Check Lists
Before startup
3
3 Check Lists
3.1 Before startup
This checklist includes all activities that will have to be executed prior to startup of a
gear unit according to Directive 94/9/EC for operation in potentially explosive atmo-
spheres.
Checked Information
Check prior to startup in potentially explosive atmospheres
in section ...
Inspect the shipment for any damage that may have occurred in transit as soon as you receive the deliv- 2.6
ery. Inform the shipping company immediately. Startup may have to be precluded. Remove transportation
safety fixtures prior to startup.
Does the following information on the gear unit nameplate correspond with the permitted conditions for 4.7 and 5.5
potentially explosive atmospheres on site:
• Equipment group
• Atex category
• Atex zone
• Temperature class
• Maximum surface temperature
Have arrangements been made to prevent explosive atmospheres, oils, acids, gases, vapors or radiation 5.2
during installation of the gear unit?
Is the ambient temperature maintained according to the lubricant table? 9.2
Have arrangements been made for sufficient ventilation and that there will be no external heat generation 5.3 and 5.5
(e.g. via clutches)? The cooling air may not exceed a temperature of 40 °C.
Does the mounting position on the gear unit nameplate correspond to the indicated mounting position? 5.3 and 8.1
Important: The mounting position may only be changed after consultation with SEW-EURODRIVE. ATEX
approval will become void without prior consultation.
Does the oil level for the mounting position on the gear unit nameplate correspond to the indicated oil fill 5.3
quantity?
Are all oil check and drain plugs as well as breather plugs and valves freely accessible? 5.3
Do all input and output elements to be installed have ATEX certification? 5.4.2
Have you checked that the data on the nameplate of the gear unit are not exceeded for standalone gear 6.2
units with adapter or input shaft assembly?
When mounting gear units with hollow shaft and shrink disk: 5.8
• Is the cover mounted properly?
When mounting the coupling of AM, AQA adapters: 5.11 and 5.12
• You must not use distance bushings as an assembly tool!
When mounting a motor on the AD input shaft assembly: 5.14
• Has the belt between input shaft end and motor shaft sufficient electrical leakage resistance < 109 ȍ?
• Before mounting a protection cover: Does a risk analysis performed by the manufacturer of the protec-
tion cover demonstrate that no sources of ignition can occur (such as impact sparks from grinding)?
For mains-operated motors: 6.2
• Check that the data specified on the nameplate of the gear unit and the motor corresponds to the
ambient conditions at the location where the drive is to be installed.
For inverter-operated gearmotors: Check that the gearmotor is approved for operation with an inverter 6.5
• The parameter settings made for the inverter must prevent the gear unit from being overloaded (see
gear unit nameplate).

Check Lists
3 During startup
3.2 During startup

This checklist includes all activities that will have to be executed during startup of a
gear unit according to Directive 94/9/EC for operation in potentially explosive atmo-
spheres.
Checked Information
Check during startup in potentially explosive atmospheres
in section ...
Measure the surface temperature after three hours of operation. Do not exceed a temperature difference of 6.2
70 K compared to the ambient temperature. If the value is > 70 K, stop the drive immediately and contact
SEW-EURODRIVE!
Measure the oil temperature. Add 10 K to the measured value. Determine lubricant change interval using 6.2
this value.
Observe for gear units with AM adapter or AD input shaft assembly with RS backstop: 5.11 and 5.12
• In rated operation, the lift-off speeds of the backstops must not drop below the minimum values.

Gear Unit Structure
Basic design of helical gear units
4
4 Gear Unit Structure

INFORMATION
The following figures are block diagrams. They help you to assign components to the
spare parts list. Discrepancies may occur depending on the gear unit size and version.
4.1 Basic design of helical gear units
[59]
[20]
[24]
[515] [101]
[516]
[517] [100]
[47] [1]
[102]
[2] [45]
[59]
[43]
[181]
[42] [3]
[41]
[6] [25]
[88]
[22]
[11] [17]
[12]
[9]
[19]
[521]
[522]
[8] [7] [523]
[59]
[31] [30]
[32]
[34] [4]
[5]
[37]
[506]
[39] [507]
[131] [508]
19194251
[1] Pinion [19] Key [42] Roller bearing [507] Shim

[2] Gearwheel [20] Breather valve [43] Key [508] Shim
[3] Pinion shaft [22] Gear unit housing [45] Roller bearing [515] Shim
[4] Gearwheel [24] Lifting eyebolt [47] Circlip [516] Shim
[5] Pinion shaft [25] Roller bearing [59] Screw plug [517] Shim
[6] Gearwheel [30] Roller bearing [88] Circlip [521] Shim
[7] Output shaft [31] Key [100] Gear cover plate [522] Shim
[8] Key [32] Spacer tube [101] Hex head screw [523] Shim
[9] Oil seal [34] Roller bearing [102] Seal
[11] Roller bearing [37] Roller bearing [131] Closing cap
[12] Circlip [39] Circlip [181] Closing cap
[17] Spacer tube [41] Circlip [506] Shim

Gear Unit Structure
4 Basic structure of parallel shaft helical gear units
4.2 Basic structure of parallel shaft helical gear units
[2] [45] [20]

[515] [59]
[516] [43] [22] [1]
[517]
[3]
[41] [42]
[181] [161]
[4] [30]
[32] [59]
[31]
[5]
[506] [37]
[507] [39] [183] [165]
[131] [508]
[160]
[19]
[102]
[88]
[94]
[25] [521] [100]
[92] [522]
[93]
[91] [523] [101]
[7]
[59]
[17]
[6]
[9]
[11]
[81]
[14]
[16]
19298059
[1] Pinion [22] Gear unit housing [91] Retaining ring [506] Shim
[2] Gear [25] Rolling bearing [92] Washer [507] Shim
[3] Pinion shaft [30] Rolling bearing [93] Lock washer [508] Shim
[4] Gear [31] Key [94] Hexagon screw [515] Shim
[5] Pinion shaft [32] Spacer tube [100] Inspection cover [516] Shim
[6] Gear [37] Rolling bearing [101] Hexagon screw [517] Shim
[7] Hollow shaft [39] Retaining ring [102] Seal [521] Shim
[9] Oil seal [41] Retaining ring [131] Closing cap [522] Shim
[11] Rolling bearing bearing [42] Rolling bearing [160] Closing plug [523] Shim
[14] Hexagon screw [43] Key [161] Closing cap
[16] Output flange [45] Rolling bearing [165] Closing plug
[17] Spacer tube [59] Screw plug [181] Closing cap
[19] Key [81] Shield ring [183] Oil seal
[20] Breather valve [88] Retaining ring

Gear Unit Structure
Basic structure of helical-bevel gear units
4
4.3 Basic structure of helical-bevel gear units
[100] [102]
[3] [20]
[536]
[43] [537] [533] [59]
[538] [534] [22]
[535]
[45] [2]
[114]
[101]
[113]
[42] [119] [59]
[116]
[523] [89] [59]
[522]
[521][88]
[25]
[84] [1]
[19]
[7] [59]
[8]
[6] [59]
[83] [17]
[11]
[12]
[9] [161]
[132]
[133]
[31]
[30] [542]
[543]
[135] [544]
[4]
[5]
[131] [37]
[506]
[507]
[137] [508]
19301131
[1] Pinion [25] Rolling bearing [102] Seal [522] Shim

[2] Gear [30] Rolling bearing [113] Slotted nut [523] Shim
[3] Pinion shaft [31] Key [114] Multi-tang washer [533] Shim
[4] Gear [37] Rolling bearing [116] Thread locker [534] Shim
[5] Pinion shaft [39] Retaining ring [119] Spacer tube [535] Shim
[6] Gear [42] Rolling bearing [131] Closing cap [536] Shim
[7] Output shaft [43] Key [132] Retaining ring [537] Shim
[8] Key [45] Rolling bearing [133] Supporting ring [538] Shim
[9] Oil seal [59] Screw plug [135] Shield ring [542] Shim
[11] Rolling bearing [83] Shield ring [161] Closing cap [543] Shim
[12] Retaining ring [84] Shield ring [506] Shim [544] Shim
[17] Spacer tube [88] Retaining ring [507] Shim
[19] Key [89] Closing cap [508] Shim
[20] Breather valve [100] Inspection cover [521] Shim
[22] Gear unit housing [101] Hexagon screw [521] Shim

Gear Unit Structure
4 Basic design of helical-worm gear units
4.4 Basic design of helical-worm gear units
[59]
[101] [20]
[506] [100]
[131] [507]
[39] [137]
[37] [102]
[22]
[5]
[43] [30] [2] [61] [59]
[1]
[19]
[89]
[59]
[523] [88]
[25] [522]
[521]
[7]
[6]
[11]
[520]
[12] [519]
[518]
[9]
19304203
[1] Pinion [20] Breather valve [88] Circlip [518] Shim

[2] Gearwheel [22] Gear unit housing [89] Closing cap [519] Shim
[5] Worm [25] Roller bearing [100] Gear cover plate [520] Shim
[6] Worm gear [30] Roller bearing [101] Hex head screw [521] Shim
[7] Output shaft [37] Roller bearing [102] Seal [522] Shim
[9] Oil seal [39] Circlip [131] Closing cap [523] Shim
[11] Roller bearing [43] Key [137] Supporting ring
[12] Circlip [59] Screw plug [506] Shim
[19] Key [61] Circlip [507] Shim

Gear Unit Structure
Basic design of SPIROPLAN® W10-W30 gear units
4
4.5 Basic design of SPIROPLAN® W10-W30 gear units
[100] [101]
[65]
[66]
[102] [68]
[71] [143]
[72]
[1]
[22]
[89]
[88]
[521]
[522]
[523]
[25]
[6]
[19] [250]
[251]
[17]
[8]
[7]
[11]
[518]
[519]
[12] [520]
[9]
19307275
[1] Pinion [19] Key [88] Circlip [251] Circlip

[6] Gearwheel [22] Gear unit housing [89] Closing cap [518] Shim
[7] Output shaft [25] Roller bearing [100] Gear cover plate [519] Shim
[8] Key [65] Oil seal [101] Hex head screw [520] Shim
[9] Oil seal [66] Roller bearing [102] Seal [521] Shim
[11] Roller bearing [71] Supporting ring [132] Circlip [522] Shim
[12] Circlip [72] Circlip [183] Oil seal [523] Shim
[17] Spacer tube [143] Supporting ring [250] Circlip

Gear Unit Structure
4 Basic design of SPIROPLAN® W37 gear units
4.6 Basic design of SPIROPLAN® W37 gear units
[521]
[89]
[522]
[523] [88]
[6] [25]
[22]
[19]
[7]
[8]
[59] [5]
[518] [33]
[519] [11]
[520] [32]
[12]
[9] [59]
[44] [133] [1]
[506] [37]
[5]
[31]
[30]
[137]
[2]
[61]
[26] [36]
605872395
[1] Pinion [22] Gear unit housing [44] O-ring [137] Shim
[2] Wheel [24] Eyebolt [59] Screw plug [150] Hex nut
[5] Pinion shaft [25] Grooved ball bearing [61] Retaining ring [183] Oil seal
[6] Wheel [26] Housing stage 1 [68] Retaining ring [506] Shim
[7] Output shaft [30] Grooved ball bearing [72] Retaining ring [518] Shim
[8] Key [31] Key [80] Key [519] Shim
[9] Oil seal [32] Spacer tube [88] Retaining ring [520] Shim
[11] Grooved ball bearing [33] Retaining ring [89] Closing cap [521] Shim
[12] Retaining ring [36] Hex head screw [106] Stud [522] Shim
[19] Key [37] Grooved ball bearing [133] Shim [523] Shim

Gear Unit Structure
Nameplate and type designation
4
4.7 Nameplate and type designation

4.7.1 Nameplate
SEW - Eurodrive
76646 Bruchsal/Germany
RF47/A/II2GD IM M1
na r/min 40 ne max r/min 1380 fB 3,1

Ma Nm 89 Me max Nm 2,6 kg 13,4
Fra max N 5313 i 34,73
FSA GmbH, EU Code 0588 IP 65
RF47/A/II2GD Made in Germany
CLP HC 220 Synth. Öl / 0,65l 0641 543 1
210927627
fb = Service factor
FRa max [N] = Maximum overhung load on the output side
FRe max [N] = Maximum overhung load on the input side (with input shaft assembly AD)
i = Gear unit reduction ratio
IM = Mounting position
IP.. = Degree of protection
ne max [rpm] = maximum input speed
na [rpm] = Output speed
Memax [Nm] = maximum input torque
Ma [Nm] = Output torque
MR [Nm] = Overload torque when using an AR adapter
MRS [Nm] = Locking torque of the backstop
Information about
special markings

In some cases SEW gear units/gearmotors must only be operated in compliance with
special measures. For these cases, there is a special indication on the nameplate
"II..X".
These special measures may be necessary due to varying reasons (e.g. intermittent
operation only, reduced output torque, etc.). The customer has been informed about
the required special measures on the initial distribution of the gear unit/gearmotor. The
customer is obliged to ensure the compliance with these special measures.
EAC marking
On requests, the explosion-proof gear units from SEW-EURODRIVE meet the require-
ments of the technical regulations of the Eurasian Economic customs union (Russia,
Kazakhstan, Belarus, and Armenia). The EAC marking on the product certifies the
conformity with the safety requirement of the Customs Union.

Gear Unit Structure
4 Nameplate and type designation
4.7.2 Type designation

For a detailed overview of type designations and additional information, refer to the fol-
lowing publications:
• "Explosion-Proof Gearmotors" catalog
• "Explosion-Proof AC Motors" catalog
Example: Helical
gear unit, category
RF 47 /A /II2GD
II2GD
Explosion-proof design to directive 94/9/EC
For direct motor mounting
Gear unit size
Helical gear unit series (flange mounted)

Mechanical Installation
Required tools/resources
5
5 Mechanical Installation
5.1 Required tools/resources
• Set of wrenches
• If necessary, torque wrench for:
– Shrink disks
– Motor adapter AQH Or EWH
– Input shaft assembly with centering shoulder
• Mounting device
• Compensation elements (shims, spacing rings)
• Fasteners for input and output elements
• Lubricant (e.g. NOCO® Fluid)
• Bolt locking compound (for input shaft assembly with centering shoulder), e.g.
Loctite® 243
Standard parts are not included in the delivery
5.1.1 Installation tolerances
Shaft end Flanges

Diameter tolerance in accordance with DIN 748 Centering shoulder tolerance to DIN 42948
• ISO k6 for solid shafts with Ø 50 mm • ISO j6 for b1 230 mm
• ISO m6 for solid shafts with Ø > 50 mm • ISO h6 with b1 > 230 mm
• ISO H7 for hollow shafts
• Center bore in accordance with DIN 332, shape
DR

5 Installation requirements
5.2 Installation requirements
CAUTION
Risk of injury due to protruding gear unit parts.
Minor injuries.
• Keep a sufficient safety distance to the gear unit/gearmotor.
NOTICE
Damage to the gear unit/gearmotor due to improper installation.
Possible damage to property
• Do closely observe the notes in this chapter.

Check the transportation packaging for oil residues. Oil residues could indicate an oil
leak. In this case, the lubrication of the gear unit is not guaranteed. This could cause
excessive temperature on the surface.
Please contact SEW-EURODRIVE if there are oil residues on the gear unit.
Check that the following conditions have been met:

• The entries on the nameplate of the gearmotor match the voltage supply system.
• The drive has not been damaged during transportation or storage.
• Ensure that the following requirements have been met:
For standard gear units:
– Ambient temperature according to the technical documentation, nameplate and
lubricant table in section "Lubricants" (page 138).
– No harmful oils, acids, gases, vapors, radiation etc. in the vicinity
For special versions:
– The drive is designed in accordance with the ambient conditions. Refer to the in-
formation on the nameplate.
For helical-worm/SPIROPLAN® W gear units:
– No large external mass moments of inertia which could exert a retrodriving load
on the gear unit.
[for Ș’ (retrodriving) = 2 – 1/Ș < 0.5 self-locking]
• You must clean the output shafts and flange surfaces thoroughly to ensure they are
free of anti-corrosion agents, contamination or similar. Use a commercially available
solvent. Do not expose the sealing lips of the oil seals to the solvent – damage to the
material.
• When the drive is installed in abrasive ambient conditions, protect the output end oil
seals against wear.

Installing the gear unit
5
5.3 Installing the gear unit
NOTICE
Improper assembly may result in damages to the gear unit/gearmotor.
• Do closely observe the notes in this chapter.
• Work on the gear unit only when the machine is not in use. Secure the drive unit
against unintentional power-up.
• Protect the gear unit from direct cold air currents. Condensation may cause water to
accumulate in the oil.
The gear unit or gearmotor is only allowed to be installed in the specified mounting po-
sition. Refer to the information on the nameplate. SPIROPLAN® gear units of sizes
W10-W30 do not depend on a particular mounting position.
The support structure must have the following characteristics:
• Level
• Vibration damping
• Torsionally rigid
The maximum permitted flatness error for foot and flange mounting (guide values with
reference to DIN ISO 1101):
• Gear unit size 67: Max. 0.4 mm

• Gear unit size 77 – 107: Max. 0.5 mm
Do not tighten the housing legs and mounting flanges against one another and ensure
that you comply with the permitted overhung and axial loads! Observe chapter "Project
Planning" in the Gear unit/gearmotor catalog for calculating the permitted overhung and
axial loads.
Secure gearmotors using quality 8.8 screws.
Secure the following gearmotors using quality 10.9 screws:
• RF37, R37F with flange Ø = 120 mm
• and RZ37, RZ47, RZ57, RZ67, RZ77, RZ87
INFORMATION
When installing the gear unit, make sure that the oil level and drain plugs as well as
the breather plugs are easily accessible!

5 Installing the gear unit

• Processes that cause strong electrical charge due to fast moving particles on the
coating must be excluded.
• Prior to startup, check that the oil level is as specified for the mounting position! See
chapter "Lubricants" (page 137), or data on nameplate.
Check that the oil level is as specified for the mounting position. see chapter "Lubricants"
(page 137), or data on nameplate. The gear units are filled with the required oil volume
at the factory. There may be slight deviations at the oil level plug as a result of the mount-
ing position, which are permitted within the manufacturing tolerances.
If you change the mounting position, make sure that you change the lubricant fill
quantities and the position of the breather valve accordingly. Observe chapter "Lu-
bricant fill quantities" (page 140) and chapter "Mounting positions" (page 109).
Consult the SEW customer service if you intend to change the mounting position of K
gear units to or between M5 and M6.
Please contact our SEW customer service if you change the mounting position of size
S47 – S97 helical-worm gear units to mounting position M2 or M3.

The mounting position may only be changed after consultation with SEW-EURO-
DRIVE. ATEX approval will become void without prior consultation.
Use plastic inserts (2 – 3 mm thick) if there is a risk of electrochemical corrosion between

the gear unit and the driven machine. The material used must have an electrical leakage
resistance < 109 ȍ. Electrochemical corrosion can occur between various metals, for ex-
ample, cast iron and high-grade steel. Also fit the bolts with plastic washers.

Electrical sparks could be generated if the housing is not grounded additionally.
Possible generation of electrical sparks.
• Ground the housing additionally and use grounding screws on the motor.

5
5.3.1 Tightening torques for retaining screws

Mount the gearmotors with the following tightening torques:
Tightening torque screw / nut
Screw/nut Strength class 8.8
[Nm]
M6 11
M8 25
M10 48
M12 86
M16 210
M20 410
M24 710
M30 1450
M36 2500
M42 4600
M48 6950
M56 11100
Mount the specified gearmotors in flange-mounted design with the following increased
tightening torques:
Tightening torque screw / nut
Screw/nut
Flange Gear unit Strength class 10.9
[Nm]
120 RF37 M6 14
140 RF37, RF47 M8 35
160 RF57 M8 35
60ZR RZ37 M8 35
70ZR RZ47 M8 35
80ZR RZ57 M10 69
95ZR RZ67 M10 69
110ZR RZ77 M12 120
130ZR RZ87 M12 120
FF77, KF77,
250 M12 120
FAF77, KAF77

5.3.2 Gear unit mounting
INFORMATION
For gear units in foot/flange-mounted design in connection with VARIBLOC® variable-
speed gear units, use quality 10.9 and suitable washers for connecting the customer
flange.
To improve the friction contact between flange and mounting surface, SEW-
EURODRIVE recommends anaerobic gaskets or an anaerobic glue.
Foot-mounted gear The following table shows the thread sizes of the gear units in foot-mounted design de-
unit pending on the gear unit type and size:
Gear unit type
Screw R / R..F RX F/ K / KH..B / S W
FH..B / FA..B KV..B / KA..B
M6 07 10/20
M8 17/27/37 27/37 37 30/37/47
M10 57 47 37/47 47/57
M12 47/57/67 67 57/67 57/67 67
M16 77/87 77/87 77/87 77 77
M20 97 97/107 97 87 87
M24 107 107 97 97
M30 137 127 107/167
M36 147/167 157 127/157/187
Gear unit with B14 The following table shows the thread sizes of the gear units with B14 flange and/or hol-
flange design low shaft depending on the gear unit type and size:
and/or hollow shaft
Gear unit type
Screw RZ FAZ / FHZ KAZ / SA / WA
KHZ / KVZ SAZ / SHZ
M6 07/17/27 37 10/20/301)
M8 37/47 27/37/47 37/47 47/57 37
M10 57/67 47
M12 77/87 57/67/77 57/67/77 67/77
M16 87/97 87/97 87/97
M20 107/127 107/127
M24 157 157
1) For W30 gear units mounted directly to a CMP motor or mounted via an EWH.. adapter, the thread size
is M8.

5
Gear unit with B5 The following table shows the thread sizes of the gear units with B5 flange depending
flange on the gear unit type, size and flange diameter:
Gear unit type
Ø flange Screw RF / FF / KF / KAF / SF / WF / WAF
[mm] R..F / RM FAF / FHF KHF / KVF SAF /SHF
80 M6 10
110 M8 20
120 M6 07/17/27 37 10/20/30/37
140 M8 07/17/27/37/47
160 M8 07/17/27/37/47 27/37 37 37/47 30/37/47
200 M10 37/47/57/67 47 47 57/67
250 M12 57/67/77/87 57/67 57/67 77
300 M12 67/77/87 77 77
350 M16 77/87/97/107 87 87 87
450 M16 97/107/137/147 97/107 97/107 97
550 M16 107/137/147/167 127 127
660 M20 147/167 157 157

5.3.3 Installation in damp locations or in the open

Drives are supplied in corrosion-resistant versions with an according surface protection
coating for use in damp areas or outdoors. Repair any damage to the paint work (e.g.
on the breather valve or the eyebolts).
When mounting the motors onto AM, AQ, AR, AT adapters and to start-up and friction
couplings, seal the flange areas with a suitable sealing compound, e.g. Loctite® 574.
Units installed outdoors must be protected from the sun. Suitable protective devices are
required, such as covers or roofs. Avoid any heat accumulation. The operator must en-
sure that foreign objects do not impair the function of the gear unit (e.g. falling objects
or coverings).
5.3.4 Components made of elastomers with fluorocarbon rubber

Under normal operating conditions and at temperatures up to 200 °C, fluorocarbon rub-
ber is very stable and safe. However, when heated to more than 300 °C, e.g. by fire or
the flame of a cutting torch, it forms harmful gases and vapors as well as harmful resi-
due.
.
CAUTION
Irritation and injuries caused by improper handling of fluorocarbon rubber
Injuries
• Components containing fluorocarbon rubber must be protected from excessive
thermal load or removed in order to prevent the forming of harmful gases, vapors,
or residue.
• Avoid inhaling the gases and vapors as well as skin and eye contact, also after the
fluorocarbon rubber component has cooled down.
The following components of R..7, F..7, K..7, S..7, and SPIROPLAN® W gear units can
contain elastomers made of fluorocarbon rubber.
• Oil seals
• Breather valve
• Screw plugs
The user is responsible for safe handling during the service life including eco-friendly
disposal.
SEW-EURODRIVE is not responsible for damage caused by improper handling.

5
5.3.5 Gear unit ventilation

No breather plug is required for the following gear units:
• R07 in mounting positions M1, M2, M3, M5 and M6
• R17, R27 and F27 in mounting positions M1, M3, M5 and M6
• SPIROPLAN® W10, W20, W30 gear units
• SPIROPLAN® W37 and W47 gear units in mounting positions M1, M2, M3, M5, M6
SEW-EURODRIVE supplies all other gear units with the breather valve installed and ac-
tivated according to the particular mounting position.
Exceptions:
1. SEW supplies the following gear units with a screw plug on the vent hole provided:
– Pivoted mounting positions, if possible
– Gear units for mounting on a slant
The breather valve is located in the motor terminal box. Before startup, you must re-
place the highest screw plug with the provided breather valve.
2. SEW supplies a breather valve in a plastic bag for gear head units requiring venting
on the input end.
3. Enclosed gear units are supplied without a breather valve.

The assembly of mount-on gear units with motors or adapters may be performed by
authorized personnel only. Please consult SEW-EURODRIVE.

Activating the Check whether the breather valve is activated. If the breather valve has not been acti-
breather valve vated, you must remove the transport fixture from the breather valve before starting up
the gear unit!
1. Breather valve with transport fixture
211319051
2. Removing the transport fixture
211316875
3. Activated breather valve
211314699

Gear unit with solid shaft
5
5.3.6 Painting the gear unit
NOTICE
Breather valves and oil seals may be damaged during painting or re-painting.
Potential damage to property.
• Thoroughly cover the breather valves and the sealing lip of the oil seals with strips
prior to painting.
• Remove the strips after painting.
5.4 Gear unit with solid shaft

5.4.1 Notes on installation

Only use input and output elements with ATEX certification, if these are subject to Di-
rective 94/9/EC.
• Only use a mounting device for installing input and output elements. Use the center
bore and the thread on the shaft end for positioning.
INFORMATION
Use belts with sufficient electrical bleeder resistance < 109 ȍ only.
• These have to meet the requirements set forth in IEC 60695-11-10, category FV-0.
• Power transmission elements should be balanced after fitting and must not give
rise to any impermissible radial or axial forces (see the "Gearmotors" or "Explosion-
Proof Gearmotors" catalog for permitted values).
INFORMATION
Mounting is easier if you first apply lubricant to the output element or heat it up briefly
(to 80 - 100 °C).

5 Gear unit with solid shaft
5.4.2 Assembling input and output elements
CAUTION
Bearing, hosing or shaft may be damaged due to improper assembly.
• Only assemble the input and output components with a mounting device. Use the
center bore and the thread on the shaft end for positioning.
• Never force belt pulleys, couplings, pinions, etc. onto the shaft end by hitting them
with a hammer.
• In the case of belt pulleys, make sure the belt is tensioned correctly in accordance
with the manufacturer's instructions.
• Power transmission elements should be balanced after fitting and must not give
rise to any impermissible radial or axial forces (see the "Gearmotors" or "Explosion-
Proof Drives" catalog for permitted values).
Using a mounting The following figure shows a mounting device for installing couplings or hubs on gear
device unit or motor shaft ends. Should you be able to tighten the screw without any problems,
you may not need the thrust bearing on the mounting device.
[1] [2]
[3]
211368587
[1] Gear unit shaft end

[2] Thrust bearing
[3] Coupling hub

Gear unit with solid shaft
5
Avoiding excessive Avoid high overhung loads by: Installing the gear or chain sprocket according to figure
overhung loads B if possible.
[1] [1]
[A] [B]
211364235
[1] Hub
[A] unfavorable
[B] correct
INFORMATION
Mounting is easier if you first apply lubricant to the output element or heat it up briefly
(to 80 - 100 °C).
5.4.3 Mounting of couplings
CAUTION
Input and output components such as belt pulleys, couplings etc. are in fast motion
during operation.
Risk of jamming and crushing.
• Cover input and output components with a touch guard.
Adjust the following misalignments according to the coupling manufacturer's specifica-
tions when mounting couplings.
a) Maximum and minimum clearance
b) Axial offset
c) Angular offset
a) b) c)
211395595

5 Gear units and gearmotors in category II2GD
5.5 Gear units and gearmotors in category II2GD

• Explosion-proof gear units and gearmotors of the R..7, F..7, K..7, S..7, and
SPIROPLAN® W series comply with the design requirements for equipment group
II, categories 2G (potentially explosive gas atmosphere) and 2D (potentially explo-
sive dust atmosphere). These units are intended for use in zones 1 and 21.
• The explosion-proof R..7, F..7, K..7 and S..7 series gear units with AR adapter
(adapter with torque limiting coupling) comply with equipment group II, category 3G
(potentially explosive gas atmosphere) and 3D (potentially explosive dust atmo-
sphere). These units are intended for use in zones 2 and 22.
• Do not operate gear units and gearmotors of the SPIROPLAN® W10.. series in a
potentially explosive atmosphere.
5.5.1 Ambient temperature

Gear units in category II2GD may be operated at ambient temperatures of –20 °C to
+40 °C only.

Any ambient temperatures deviating from this range have to be listed on the name-
plate.
5.5.2 Temperature class

Mains-operated gear units gearmotors in category II2G (potentially explosive gas atmo-
sphere) are approved for temperature classes T3 to T6 depending on their speed, re-
duction ratio and mounting position. The temperature class of the gear unit is indicated
on the nameplate. The situation for single gear units and inverter-operated gearmotors
(only 4 and 6 pole) is defined depending on the application, subject to consultation with
SEW-EURODRIVE.
5.5.3 Surface temperature

The maximum surface temperature of category II2D units is 120 °C or 140 °C depending
on the speed, gear ratio, and mounting position. Lower surface temperature limits are
only permitted after consultation with SEW-EURODRIVE and must be indicated on the
nameplate. The system operator must guarantee that a possible accumulation of dust
will not exceed a maximum thickness of 5 mm, in accordance with EN 50281-1-2.

Gear units and gearmotors in category II2GD
5
5.5.4 Degree of protection

The degree of protection for all gear unit versions is IP65 according to EN 60529.
5.5.5 Ambient conditions

Provide sufficient ventilation for the gear units and prevent external heat generation (e.g.
via couplings).
5.5.6 Output power and output torque

Observe the output torque and the permitted overhung loads.
5.5.7 Special designs

Special designs (e.g. modified output shaft) may only be operated in potentially explo-
sive atmospheres after prior approval by SEW-EURODRIVE.

5 Torque arms for shaft-mounted gear units
5.6 Torque arms for shaft-mounted gear units
CAUTION
Improper assembling may result in damages to the gear unit.
• Do not place torque arms under strain during installation.
• Use bolts of quality 8.8 to fasten torque arms.
5.6.1 Parallel shaft helical gear units

The following figure shows the toque arm for parallel shaft helical gear units.
c
[3]
a
[1]
ød
[2]
øb +0.5
9007199466107403
[1] Screw
[2] Washer
[3] Nut
Proceed as follows to mount the rubber buffers:

1. Use screws [1] and washers according to the following table.
2. Use two nuts to secure the screw connection [3].
3. Tighten the screw until the initial stress "ǻ L" of the buffers is reached according to
the table.
Rubber buffer
Gear unit Diameter Internal Length Washer width ǻ L (taut)
diameter (loose)
d [mm] b [mm] c [mm] [mm] [mm]
FA27 40 12.5 20 5 1
FA37 40 12.5 20 5 1
FA47 40 12.5 20 5 1.5
FA57 40 12.5 20 5 1.5
FA67 40 12.5 20 5 1.5
FA77 60 21.0 30 10 1.5
FA87 60 21.0 30 10 1.5
FA97 80 25.0 40 12 2
FA107 80 25.0 40 12 2
FA127 100 32.0 60 15 3
FA157 120 32.0 60 15 3

Torque arms for shaft-mounted gear units
5
5.6.2 Helical-bevel gear units

The following figure shows the toque arm for helical-bevel gear units.
• Bushing [1] with bearings on both ends.
• Install connection end B as a mirror image of A.
[1]
211362059
Gear unit bolts Tightening torque

KA37 4 × M10 × 25 – 8.8 48 Nm
KA47 4 × M10 × 30 – 8.8 48 Nm
KA67 4 × M12 × 35 – 8.8 86 Nm
KA77 4 × M16 × 40 – 8.8 210 Nm
KA87 4 × M16 × 45 – 8.8 210 Nm
KA97 4 × M20 × 50 – 8.8 410 Nm
KA107 4 × M24 × 60 – 8.8 710 Nm
KA127 4 × M36 × 130 – 8.8 2500 Nm
KA157 4 × M36 × 130 – 8.8 2500 Nm
5.6.3 Helical-worm gear units

The following figure shows the torque arm for helical-worm gear units.
[1]
211491723
Gear unit bolts Tightening torque

SA37 4 x M6 × 16 – 8.8 11 Nm
SA47 4 x M8 × 20 – 8.8 25 Nm
SA57 6 x M8 × 20 – 8.8 25 Nm
SA67 8 x M12 × 25 – 8.8 86 Nm
SA77 8 x M12 × 35 – 8.8 86 Nm
SA87 8 x M16 × 35 – 8.8 210 Nm
SA97 8 x M16 × 35 – 8.8 210 Nm

5 Torque arms for shaft-mounted gear units
5.6.4 SPIROPLAN® W gear units

The following figure shows the toque arm for SPIROPLAN® W gear units.
45˚
[1]
211489547
Gear unit Screws Tightening torque Nm

WA10 4 x M6 × 16 - 8.8 11
WA20 4 x M6 × 16 - 8.8 11
WA30 4 x M6 × 16 - 8.8 11
WA37 4 x M8 × 20 - 8.8 25
WA47 4 x M10 × 25 - 8.8 48

Shaft-mounted gear units with keyway or splined hollow shaft
5
5.7 Shaft-mounted gear units with keyway or splined hollow shaft
INFORMATION
Concerning the configuration of the customer shaft, please also refer to the design
notes in the Gearmotors catalog!
5.7.1 Installation notes

1. Apply and thoroughly spread NOCO® Fluid
®
O
C
O I
N U
L
F
®
O
C
O I
N U
L
F
211516171
2. Install the shaft and secure it axially

(mounting is facilitated by using a mounting device)
The three mounting types are described below:
• 2A: Standard scope of delivery
• 2B: installation and removal kit for customer shaft with contact shoulder
• 2C: installation and removal kit for customer shaft without contact shoulder
2A: Standard installation procedure
[1]
[2]
[3]
[4]
[5]
211518347
[1] Short retaining bolt (standard delivery scope)

[2] Lock washer
[3] Washer
[4] Retaining ring
[5] Customer shaft

5 Shaft-mounted gear units with keyway or splined hollow shaft
2B: Installation with SEW-EURODRIVE installation and removal kit (page 44)
– Customer shaft with contact shoulder
[1]
[2]
[3]
[4]
[5]
211520523
[1] Retaining screw

[2] Lock washer
[3] Washer
[4] Retaining ring
[5] Customer shaft with contact shoulder
2C: Installation with SEW-EURODRIVE installation and removal kit (page 44)
– Customer shaft without contact shoulder
[1] [2]
[3]
[4]
[5]
C
[6]
211522699
[1] Retaining screw

[2] Lock washer
[3] Washer
[4] Retaining ring
[5] Spacer tube
[6] Customer shaft without contact shoulder

5
3. Tighten the retaining screw to the appropriate torque (see table).
211524875
Screw Tightening torque [Nm]

M5 5
M6 8
M10/12 20
M16 40
M20 80
M24 200
INFORMATION
To avoid contact corrosion, we recommend that the customer shaft should additionally
be lathed down between the 2 contact surfaces.

5.7.2 Removal notes

This description is only applicable when the gear unit was assembled using the installa-
tion and removal kit (page 44) from SEW-EURODRIVE. Observe section "Installation
notes (page 39)", 2B or 2C.
1. Loosen the retaining screw [1].
2. Remove parts [2] to [4] and, if applicable, the distance piece [5].
[1]
[2]
[3]
[4]
[5]
[6]
211527051
[1] Retaining screw

[2] Lock washer
[3] Washer
[4] Retaining ring
[5] Spacer tube
[6] Customer shaft
3. Insert the forcing disk [8] and the fixed nut [7] from the SEW-EURODRIVE installa-
tion/removal kit between the customer shaft [6] and the retaining ring [4].
4. Re-install the retaining ring [4].

5
5. Screw the retaining screw [1] back in. Now you can force the gear unit off the shaft
by tightening the bolt.
[1]
[4]
[7]
[8]
[6]
211529227
[1] Retaining screw

[4] Retaining ring
[6] Customer shaft
[7] Fixed nut
[8] Forcing disk

5.7.3 SEW installation and removal kit

The SEW-EURODRIVE installation/removal kit can be ordered under the following part
number.
[1]
[7]
[8] [7]
[1]
211531403
[1] Retaining screw

[7] Fixed nut for disassembly
[8] Forcing disk
Type DH7 M1) C4 C5 C6 U-0.5 T -0.5 D3-0.5 L4 Part number of

[mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] installation/
removal kit
WA..10 16 M5 5 5 12 4.5 18 15.7 50 643 712 5
WA..20 18 M6 5 6 13.5 5.5 20.5 17.7 25 643 682 X
WA..20, WA..30, SA..37, WA..37 20 M6 5 6 15.5 5.5 22.5 19.7 25 643 683 8
FA..27, SA..47, WA..47 25 M10 5 10 20 7.5 28 24.7 35 643 684 6
FA..37, KA..37, SA..47, SA..57, WA..47 30 M10 5 10 25 7.5 33 29.7 35 643 685 4
FA..47, KA..47, SA..57 35 M12 5 12 29 9.5 38 34.7 45 643 686 2
FA..57, KA..57, FA..67, KA..67, SA..67 40 M16 5 12 34 11.5 41.9 39.7 50 643 687 0
SA..67 45 M16 5 12 38.5 13.5 48.5 44.7 50 643 688 9
FA..77, KA..77, SA..77 50 M16 5 12 43.5 13.5 53.5 49.7 50 643 689 7
FA..87, KA..87, SA..77, SA..87 60 M20 5 16 56 17.5 64 59.7 60 643 690 0
FA..97, KA..97, SA..87, SA..97 70 M20 5 16 65.5 19.5 74.5 69.7 60 643 691 9
FA..107, KA..107 80 M20 5 20 75.5 21.5 85 79.7 70 106 8211 2
FA..107, KA..107, SA..97 90 M24 5 20 80 24.5 95 89.7 70 643 692 7
FA..127, KA..127 100 M24 5 20 89 27.5 106 99.7 70 643 693 5
FA..157, KA..157 120 M24 5 20 107 31 127 119.7 70 643 694 3
1) Retaining screw

5
INFORMATION
The SEW installation kit for attaching the customer shaft is a recommendation by
SEW-EURODRIVE. You must always check whether this design can compensate the
axial loads. In particular applications (e.g. mounting mixer shafts), a different design
may have to be used to secure the shaft axially. In these cases, customers can use
their own devices. However, you must ensure that these designs do not cause poten-
tial sources of combustion according to DIN EN 13463 (for example, impact sparks).

5 Shaft-mounted gear units with shrink disk
5.8 Shaft-mounted gear units with shrink disk

5.8.1 Assembly notes
NOTICE
Tightening the screws without installed shaft may result in the hollow shaft being
deformed.
• Only tighten the locking screws with the shaft installed.
1. Loosen the locking screws by a few turns (do not unscrew them completely!).
A B
211533579
2. Carefully degrease the hollow shaft hole and the input shaft using a commercial
solvent.
211535755

Shaft-mounted gear units with shrink disk
5
3. Hollow shaft/input shaft after degreasing.
211537931
4. Apply NOCO® fluid to the input shaft in the area of the bushing.
It is essential to make sure that the clamping area of the shrink disk is free from
grease. As a result, never apply NOCO® Fluid directly to the bush. This is because
the paste may be able to get into the clamping area of the shrink disk when the input
shaft is put on.
211540107

5 Shaft-mounted gear units with shrink disk
5. Install the input shaft.

– Make sure that the locking collars of the shrink disk are installed in parallel to each
other.
– For gear unit housings with shaft shoulder:
Mount the shrink disk onto the stop on the shaft shoulder.
– For gear unit housings without shaft shoulder:
Install the shrink disk with a 1 to 2 mm distance from the gear unit housing.
– Tighten the locking screws by working round with the torque wrench several times
from one screw to the next (not in diametrically opposite sequence).
The exact values for the tightening torques are shown on the shrink disk.
1-2mm s>0mm
211542283
6. After the installation, make sure the remaining gap between the outer rings is
> 0 mm.
7. Grease the the area around the shrink disk outside of the hollow shaft to prevent
corrosion.

Shaft-mounted gear units with shrink disk
5
5.8.2 Removal notes

1. Loosen the locking screws one after the other by a quarter rotation to avoid tilting the
outer rings.
2. Unscrew the locking bolts evenly one after the other. Do not remove the locking
screws completely.
3. Remove the shaft or pull the hub off the shaft. (Remove any rust that may have
formed between the hub and the end of the shaft beforehand.)
4. Remove the shrink disk from the hub.
5.8.3 Cleaning and lubrication

There is no need to dismantle removed shrink disks before they are reinstalled.
Clean and lubricate the shrink disk if it is dirty.
Lubricate the tapered surfaces with one of the following solid lubricants:
Lubricant (Mo S2) Sold as
Molykote 321 (lube coat) Spray
Molykote spray (powder spray) Spray
Molykote G Rapid Spray or paste
Aemasol MO 19P Spray or paste
Aemasol DIO-sétral 57 N (lube coat) Spray
Grease the locking screws with a multipurpose grease such as Molykote BR 2 or similar.

5 Shaft-mounted gear units with TorqLOC®
5.9 Shaft-mounted gear units with TorqLOC®

5.9.1 Installation notes for customer shaft without contact shoulder
1. Clean the customer shaft and the inside of the hollow shaft. Ensure that all traces of
grease or oil are removed.
2. Install the stop ring and the bushing on the customer shaft.
211941003
3. Mount the torque arm to the drive unit, observe chapter "Torque arms for shaft-
mounted gear units" (page 36).
5128549131
4. Apply NOCO® Fluid on the bushing and spread thoroughly.

O
C
®
O D
N UI
L
F
211938827

Shaft-mounted gear units with TorqLOC®
5
5. Push the gear unit onto the customer shaft.
9007199466677643
6. Preassemble the torque arm (do not tighten the screws).
K..
F..
S.. / W..
9007199466684171
7. Push the busing onto the gear unit up to the stop.
9007199466686347

8. Secure the bushing with the stop ring. Tighten the split ring on the bushing using the
appropriate torque as specified in the following table:
9007199466741899
Type Nickel-plated Stainless steel

[Standard]
KT / FT ST / WT Torque in Nm
- 37 18 7.5
37 47 18 7.5
47 57 18 7.5
57, 67 67 35 18
77 77 35 18
87 87 35 18
97 97 35 18
107 – 38 38
127 – 65 65
157 – 150 150
9. Make sure that all screws are loosened and slide the shrink disk onto the hollow
shaft.
9007199466744075

5
10.Slide the counter bushing onto the customer shaft and into the hollow shaft until the
shrink disk is properly seated.
UID O
®
FL OC
N
9007199466746251
11.Tap lightly on the flange of the counter bushing to ensure that the socket is fitted
securely in the hollow shaft.
9007199466748427
12.Make sure that the customer shaft is seated in the counter bushing.
9007199466750603

13.Manually tighten the screws of the shrink disk and ensure that the outer rings of the
shrink disk are parallel.
9007199466752779
14.Tighten the locking bolts by working round several times from one bolt to the next
(not in diametrically opposite sequence).
The exact values for the tightening torques are shown on the shrink disk.
> 0mm
9007199466754955
15.After the installation, make sure the remaining gap between the outer rings is
> 0 mm.
16.The remaining gap between counter bushing and hollow shaft end as well as bushing
and stop ring must be > 0 mm.
> 0 mm
> 0 mm
s
> 0 mm
9007201603402123

5
17.Securely tighten the torque arm; observe chapter "Torque arm for shaft-mounted
gear units" (page 36).
5129142283

5.9.2 Removal notes
CAUTION
Burns caused by hot surfaces.
Severe injuries.
• Let the units cool down before touching them.
1. Loosen the locking screws one after the other by a quarter rotation to
avoid tilting the outer rings.
212013963
2. Unscrew the locking bolts evenly one after the other.

Do not remove the locking screws completely.
3. Dismantle the conical steel bushing.
If required, use the outer rings as pullers as follows:
– Remove all the locking screws.
– Screw the respective number of screws in the tapped holes of the shrink disk.
– Support the inner ring against the gear unit housing.
– Pull off the conical steel bushing by tightening the screws.
4. Remove the gear unit from the shaft.
2903780235
5. Remove the shrink disk from the hub.

Installing the cover
5
5.9.3 Cleaning and lubrication

There is no need to dismantle removed shrink disks before they are reinstalled.
Clean and lubricate the shrink disk if it is dirty.
Lubricate the tapered surfaces with one of the following solid lubricants:
Lubricant (Mo S2) Sold as
Molykote 321 (lube coat) Spray
Molykote spray (powder spray) Spray
Molykote G Rapid Spray or paste
Aemasol MO 19P Spray or paste
Aemasol DIO-sétral 57 N (lube coat) Spray
Grease the locking screws with a multipurpose grease such as Molykote BR 2 or similar.
5.10 Installing the cover
CAUTION
During operation, output components are in fast motion.
Risk of jamming and crushing.
• Disconnect the motor from the power supply before starting work and safeguard
against accidental startup.
• Cover input and output components with a touch guard.

Prior to installation, make sure that
• there is a flawless glued connection between sealing and cover
• the bores of the seal and the cover correspond
5.10.1 Installing the fixed cover
1 2
1. To fasten the cover, remove the plastic plug on the gear unit housing (see figure 1)
2. Use the delivered screws to mount the cover to the gear unit housing (see figure 2).

5 Installing the cover
5.10.2 Installation without cover

In certain individual cases (e.g. through-shaft), you cannot install the cover. In such
cases, the cover is not necessary if the system or unit manufacturer provides corre-
sponding components to guarantee for the compliance with the required degree of pro-
tection to EN DIN 13463-1.
If this results in additional maintenance, you have to describe this in the operating in-
structions for the system/component.

Coupling of AM adapter
5
5.11 Coupling of AM adapter
INFORMATION
You must not use distance bushings as an assembly tool!
5.11.1 IEC adapter AM63 - 280 / NEMA adapter AM56 - 365
9007199466840971
[1] Motor shaft

[479] Coupling half
[481] Setscrew
[484] Key
[491] Spacer tube
1. Clean the motor shaft and flange surfaces of the motor and the adapter.
2. Remove the key from the motor shaft and replace it with the supplied key [484] (not
AM63 and AM250).
3. Heat the coupling half [479] to approx. 80 - 100 °C and push the coupling half onto
the motor shaft. Position as follows:
– IEC adapter AM63 - 225 Until stop at motor shaft shoulder.
– IEC adapter AM250 - 280 to dimension A.
– NEMA adapter with spacer tube [491] to dimension A.
4. Secure the key and coupling half using the setscrew [481] and tightening torque TA
according to the table on the motor shaft.

5 Coupling of AM adapter
5. Check the dimension A.

6. Seal the contact surfaces between the adapter and motor using a suitable sealing
compound.
7. Mount the motor on the adapter. Ensure that the coupling claws of the adapter shaft
are engaged in the plastic cam ring.
IEC AM 63 / 71 80 / 90 100 / 112 132 160 / 180 200 225 250 / 280
A 24.5 31.5 41.5 54 76 78.5 93.5 139
TA 1.5 1.5 4.8 4.8 10 17 17 17
Thread M4 M4 M6 M6 M8 M10 M10 M10
NEMA AM 56 143 / 145 182 / 184 213 / 215 254 / 256 284 / 286 324 / 326 364 / 365
A 46 43 55 63.5 78.5 85.5 107 107
TA 1.5 1.5 4.8 4.8 10 17 17 17
Thread M4 M4 M6 M6 M8 M10 M10 M10
INFORMATION
To avoid contact corrosion, we recommend applying NOCO® Fluid to the motor shaft
before mounting the coupling half.
CAUTION
Dampness might enter the adapter when mounting a motor to the adapter.
Potential damage to property
• Seal adapter with anaerobic fluid seal.

Coupling of AM adapter
5
Permitted loads
NOTICE
Impermissibly high loads may occur when mounting a motor.
• The load data specified in the following table are not to be exceeded.
Fq
18513419
Gear unit series R..7, F..7, K..7, and S..7:

Adapter type Fq1) [N]
IEC NEMA x1) [mm] IEC adapter NEMA adapter
AM63/71 AM56 77 530 410
AM80/90 AM143/145 113 420 380
AM100/112 AM182/184 144 2000 1760
AM1322) AM213/21522) 1600 1250
186
AM132.. AM213/215 4700 3690
AM160/180 AM254/286 251 4600 4340
AM200/225 AM324-AM365 297 5600 5250
AM250/280 - 390 11200 –
1) The maximum permitted weight of the attached motor Fqmax must be reduced linearly as the center of
gravity distance x increases. If this distance is reduced, the maximum permitted weight Fqmax cannot be
increased.
2) Diameter of the adapter output flange: 160 mm
Gear unit series SPIROPLAN® W37 – W47:

Adapter type Fq1) [N]
IEC NEMA x1) [mm] IEC adapter NEMA adapter
AM63/71 AM56 115 140 120
AM80/90 AM143/145 151 270 255
1) The maximum permitted weight of the attached motor Fqmax must be reduced linearly as the center of
gravity distance x increases. If this distance is reduced, the maximum permitted weight Fqmax cannot be
increased.

5 Coupling of AM adapter
AM adapter with Check the direction of rotation of the drive prior to assembly or startup. Inform the SEW-
AM../RS backstop EURODRIVE service in the case of incorrect direction of rotation.
The backstop is maintenance-free in operation, and does not require any further main-
tenance work. Backstops have a minimum lift-off speed depending on the size (see fol-
lowing table).
.
NOTICE
If the actual speed level is below the minimum lift-off speed level, the backstops are
subject to wear, and the resulting friction causes the temperature to increase.
• In rated operation, the lift-off speeds must not drop below the minimum values.
• During startup or braking, the lift-off speeds may drop below the minimum levels.
Maximum locking torque of the backstop Minimum lift-off speed

Type
[Nm] [rpm]
AM80/90/RS,
65 820
AM143/145/RS
AM100/112/RS,
425 620
AM182/184/RS
AM132/RS,
850 530
AM213/215/RS
AM160/180/RS,
1450 480
AM254/286/RS
AM200/225/RS,
1950 450
AM324-365/RS
AM250/280/RS, 1950 450

Coupling of AQ adapter
5
5.12 Coupling of AQ adapter

You must not use distance bushings as an assembly tool!
5.12.1 AQA80 - 190 adapter / AQH80 - 190 adapter
AQA AQH
479
479
1
1
2 3
A A
212114955
1 Motor shaft
2 Grub screw
3 screws
AQA = With keyway

AQH = Without keyway
1. Clean the motor shaft and the flange surfaces of the motor and the adapter.
2. Type AQH: Loosen the screws of the coupling half (479) and loosen the conical con-
nection.
3. Heat up the coupling half (80 °C – 100 °C) and slide it onto the motor shaft.
AQA / AQH design: up to clearance "A" (see table)

5 Coupling of AQ adapter
4. Type AQH: Tighten the screws evenly in diametrically opposite sequence, working
round several times. Make sure that all the screws are tightened with the tightening
torque TA according to the following table.
Type AQA: Secure the coupling halves using the setscrew (see table).
5. Check the position of the coupling half (clearance "A", see table).
Mount the motor onto the adapter, making sure that the claws of the two coupling
halves engage in each other. The force that must be applied when joining the two
coupling halves is dissipated after final assembly, so there is no risk of any axial load
being applied to adjacent bearings.
INFORMATION
Only for AQA, not permitted for AQH: To avoid contact corrosion, we recommend
applying NOCO®® Fluid to the motor shaft before mounting the coupling half.
NOTICE
Dampness might enter the adapter when mounting a motor to the adapter.
• Seal adapter with anaerobic fluid seal
5.12.2 Setting dimensions / tightening torques
Type Coupling size Clearance "A" Screws Tightening torque TA

[mm] [Nm]
AQA AQH AQA AQH
AQA /AQH 80 /1 /2 /3 44.5
AQA /AQH 100 /1 /2 39
19 M5 6 x M4 2 4.1
AQA /AQH 100 /3 /4 53
AQA /AQH 115 /1 /2 62
AQA /AQH 115 /3 62
24 M5 4 x M5 2 8.5
AQA /AQH 140 /1 /2 62
AQA /AQH 140 /3 /4 74.5
AQA /AQH 160 /1 28 74.5 M8 8 x M5 10 8.5
AQA /AQH 190 /1 /2 76.5
AQA /AQH 190 /3 38 100 M8 8 x M6 10 14

Adapter with a torque limiting coupling AR
5
5.13 Adapter with a torque limiting coupling AR
1 2 3 4 5 6 7 8
[1] Trigger cams [4] Friction lining [7] Friction hub

[2] Encoder [5] Cup spring [8] Speed monitor
[3] Driving disk [6] Slotted nut
Drives with a torque limiting coupling consist of a standard gear unit and motor/variable
speed geared motor with an adapter installed between them. The torque limiting cou-
pling is installed in this adapter. In gearmotors with a multi-stage gear unit, the torque
limiting coupling may be located between the first and second gear units.
Via the friction lining [4] of the driving disk [3], the input friction hub [7] with cup springs
[5] and slotted nut [6] drives the output coupling plate with connecting pin. The slip
torque is individually set in the factory according to the specific drive selection.
The speed of the coupling plate at the output end is picked up by an encoder [2] and
passed on to a monitoring unit [8]. Speed monitors and slip monitors are used as mon-
itoring units. These can be mounted in conjunction with contactors, fuse units, etc. on a
standard 35 mm rail (to DIN EN 50022) in the switch cabinet or they can be attached
using two holes.
5.13.1 WEX speed monitor

The speed monitor [8] is used with constant-speed gearmotors and is connected to the
encoder [2] in the adapter.

5 Adapter with a torque limiting coupling AR
5.13.2 Assembly
Encoder installa- 1. Remove the fan guard from the driving motor
tion
2. Slowly turn the motor and adapter shaft end until you can see a cam (= head of the
pan head screw) in the tapped hole.
3. Screw in the encoder until contact is made with the cam
4. Turn the encoder [1] back by two turns (corresponds to a clearance of 2 mm)
[1]
2 mm
5. Secure the encoder with a lock nut on the outside of the encoder
6. Check: Slowly turn the motor or adapter shaft end
Correct assembly: Cams do not touch the encoder
7. Mount fan guard

The speed monitor must be located outside the potentially explosive atmosphere.

AD input shaft assembly
5
Connecting moni-
toring devices

Do not route the supply cables in multicore cables to avoid interference from
parasitic voltages. Maximum line lengths 500 m with core cross section
1.5 mm2. Use shielded cables if there is a risk of interference from power cur-
rent or control cables and if the lines are longer than 10 m.
You must observe the respectively applicable standards. Especially in poten-
tially explosive atmospheres!
1. For design with WEX speed monitor

Connect the incremental encoder of the adapter to the speed monitor
• Via 2-core cable
• Incremental encoder generates one pulse per revolution
2. Connect the speed monitor according to the wiring diagram supplied with the brake.
5.14 AD input shaft assembly

Observe section "Assembling the input and output components" (page 32) when install-
ing input components.

Use belts with sufficient discharge resistance (< 109 ȍ).
• Before a protection cover can be installed, a risk analysis must demonstrate that
no sources of ignition (e.g. impact sparks from grinding) can occur. The manufac-
turer of the protection cover must perform the risk analysis.

5 AD input shaft assembly
5.14.1 AD../P – cover with motor mounting platform

Mounting the motor and adjusting the motor mounting platform.
212119307
[1] Motor mounting platform

[2] Stud bolt (only AD6/P / AD7/P)
[3] Support (only AD6/P / AD7/P)
[4] Nut
[5] Threaded column
1. Set the motor mounting platform to the required mounting position by evenly tighten-
ing the adjusting nuts. Remove the lifting eyebolt from helical gear units in order to
achieve the lowest adjustment position. Touch up any damage to the paint work.
2. Align the motor on the motor mounting platform (shaft ends must be in alignment)
and secure it.
3. Mount the input elements on the input shaft end and the motor shaft, line them up
with one another and correct the motor position again, if necessary.
4. Put on the traction elements (V-belt, chain, etc.) and apply a preload by evenly ad-
justing the motor mounting platform. Do not stress the motor mounting platform and
the columns against each other when doing this.
5. Tighten all the nuts not used for adjustment in order to fix the threaded columns.

5
5.14.2 Only AD6/P and AD7/P

Unscrew the nuts on the stud bolts before adjustment to allow the stud bolts to move
axially in the support without restriction. Do not tighten the nuts until the final adjustment
position has been reached. Do not adjust the motor mounting platform using the support.
5.14.3 AD../ZR input shaft assembly with centering shoulder

Mounting applications on the input shaft assembly with centering shoulder.
1. Retaining bolts of a suitable length must be used to secure the application. The
length l of the new bolts is calculated as follows:
212121483
[l] t+a
[t] Screw-in depth (see table)
[a] Thickness of the application
[s] Retaining thread (see table)
Round down the calculated screw length to the next smaller standard length.
2. Remove the retaining screws from the centering shoulder.
3. Clean the contact surface and the centering shoulder.

4. Clean the threads of the new bolts and apply a bolt locking compound (e.g. Loctite®
243) to the first few threads.
5. Attach the application to the centering shoulder and tighten the retaining screws with
the specified tightening torque TA (see table).
Screw-in Tightening torque
Retaining thread
Type depth TA for connection screws of strength class
s
t [mm] 8.8 [Nm]
AD2/ZR 25.5 M8 25
AD3/ZR 31.5 M10 48
AD4/ZR 36 M12 86
AD5/ZR 44 M12 86
AD6/ZR 48.5 M16 210
AD7/ZR 49 M20 410
AD8/ZR 42 M12 86

5
Permitted loads
NOTICE
Impermissibly high loads may occur when mounting a motor.
• The load data specified in the following table are not to be exceeded.
The following figure shows the permitted force application points for the permitted max-
imum weights:
Fq
212123659
Motor's center of gravity

X Distance from adapter flange to the middle of
the motor
Fq Overhung load
x1) Fq1)
Type
[mm] [N]
AD2/ZR 193 330
AD3/ZR 274 1400
AD4/ZR2) 1120
361
AD4/ZR 3300
AD5/ZR 487 3200
AD6/ZR 567 3900
AD7/ZR 663 10000
AD8/ZR 516 4300
1) Maximum load values for connection screws of strength class 8.8. The maximum permitted weight of
the attached motor Fqmax must be reduced linearly as the center of gravity distance x increases. When
this distance is reduced, Fqmax cannot be increased.
2) Diameter of the adapter output flange: 160 mm

5.14.4 AD../RS – cover with backstop

Check the direction of rotation of the drive prior to assembly or startup. Inform the SEW-
EURODRIVE service in the case of incorrect direction of rotation.
The backstop is maintenance-free in operation, and does not require any further main-
tenance work. Backstops have a minimum lift-off speed depending on the size (see fol-
lowing table).
NOTICE
If the actual speed level is below the minimum lift-off speed level, the backstops are
subject to wear, and the resulting friction causes the temperature to increase.
• In rated operation, the lift-off speeds must not drop below the minimum values.
• During startup or braking, the lift-off speeds may drop below the minimum levels.
Maximum locking torque of the backstop Minimum lift-off speed

Type
[Nm] [rpm]
AD2/RS 65 820
AD3/RS 425 620
AD4/RS 850 530
AD5/RS 1450 480
AD6/RS 1950 450
AD7/RS 1950 450
AD8/RS 1950 450

Startup I
6
0
6 Startup
NOTICE
Improper startup may result in damage to the gear unit.
Possible damage to property.
• Note the following:
• Before startup, check that the oil level is correct. Refer to the unit's nameplate for lu-
bricant fill quantities.
• The oil checking and drain screws and the breather valves must be freely accessible.
• The most important technical data is provided on the nameplate. Additional data rel-
evant for operation is available in drawings and the order confirmation.
• Ensure that all retaining screws are tight after the gear unit has been installed.
• Make sure that the orientation has not changed after tightening the mounting ele-
ments.
• Prior to startup, ensure that rotating shafts as well as couplings are equipped with
suitable protective covers.
• If an oil sight glass is used for checking the oil level, ensure that it is protected against
damage.
• It is essential that there is no open fire or risk of sparks when working on the gear unit.
• Protect the gear unit from falling objects.
• Remove transport fixtures prior to startup.
• Strictly observe the safety notes in the individual chapters.

I Startup
6 Checking the oil level
0
6.1 Checking the oil level
NOTICE
Damage to the gear unit due to oil leaking from the oil sight glass.
Possible damage to the unit.
• Attach a suitable protective device to exclude damage to the oil sight glass as a
result from shock or blows.
Before startup, make sure that the oil level corresponds to the mounting position. Ob-
serve section "Checking the oil level and changing the oil" (page 92).
If the gear unit is equipped with an oil sight glass, you can also determine the oil level at
the oil sight glass.
1. Observe the notes in chapter "Preliminary work regarding inspection/maintenance".
2. Check the oil level at the oil sight glass according to the following figure:
[1]
4158756363
[1] The oil level must be within this range
3. Proceed as follows if the oil level is too low:

– Open the respective oil fill plug, see chapter "Inspection/maintenance for the gear
unit".
– Fill in new oil of the same type via the oil fill plug up to the mark.
– Screw in the oil fill plug.

Startup I
Measuring the surface and oil temperature
6
0
6.2 Measuring the surface and oil temperature
INFORMATION
The nameplate data on maximum surface temperature is based on measurements at
standard ambient conditions and installation altitudes. Even slight changes of these
conditions (such as limited installation space) can have a tremendous impact on the
temperature.
6.2.1 Measuring the surface temperature

It is absolutely necessary to measure the surface temperature at maximum load during
startup of the gear unit. A commercially available thermometer is sufficient for this mea-
surement. Measure the surface temperature at the transition space between gear unit
and motor where the position of the terminal box prevents venting by the motor fan. The
maximum surface temperature will be reached after approximately three hours and
must not exceed a difference value of 70 K when compared with the ambient temper-
ature.

Stop the drive immediately if the difference exceeds the given value. Consult SEW-
EURODRIVE!
For gear units with AM, AQ, AR adapter, or AD input shaft assembly, the surface tem-
perature is measured at the joint between input gear unit flange and customer motor
flange (see following picture).
°C
18669579
6.2.2 Measuring the oil temperature

It is necessary to measure the oil temperature to determine the lubricant change inter-
vals set forth in the section Inspection and Maintenance. (page 84) To do so, measure
the temperature at the bottom of the gear unit. In gear units with oil drain plug, you will
have to measure the temperature at the oil drain plug. Add 10 K to the measured value.
Use this temperature value to determine the lubricant change interval.

I Startup
6 Pseudo-leakage at shaft seals
0
6.3 Pseudo-leakage at shaft seals

Due to their operating principle, seals between moving surfaces at shaft passages can-
not be completely tight, as a lubricant film must form during operation. The lubricant film
between shaft and sealing lip keeps the development of heat and wear on the sealing
system to a minimum and ensures the intended service life. The optimum sealing prop-
erties are only achieved after the run-in phase.
6.4 Helical-worm and SPIROPLAN® W gear units

6.4.1 Run-in period
SPIROPLAN® and helical-worm gear units require a running-in period of at least 48 h
before reaching their maximum efficiency. A separate run-in period applies for each di-
rection of rotation if the gear unit is operated in both directions of rotation. The table
shows the average power reduction during the run-in period.
Helical-worm gear
unit
Worm
i range Ș reduction
1-start approx. 50 ... 280 approx. 12 %
4-start - -
SPIROPLAN®
gear unit
W10 / W20 / W30 W37 / W47
i range Ș reduction i range Ș reduction
Approx. 35 ... 75 Approx. 15%
Approx. 20 ... 35 Approx. 10%
Approx. 10 ... 20 Approx. 8% Approx. 30...70 Approx. 8%
Approx. 8 Approx. 5% Approx. 10 ... 30 Approx. 5%
Approx. 6 Approx. 3% Approx. 3...10 Approx. 3%

Startup I
Helical/parallel shaft helical/helical-bevel gear units
6
0
6.5 Helical/parallel shaft helical/helical-bevel gear units

6.5.1 Stand-alone gear units
For gear units with an adapter, or input shaft assembly, you must ensure that the data
specified on the nameplate are not exceeded. It is essential that the gear unit is not over-
loaded.
6.5.2 Motors operated on the supply system

Make sure that the data specified on the nameplate of the gear unit and the motor cor-
responds to the ambient conditions at the location where the drive is to be installed.
6.5.3 Inverter-operated gearmotors

• Make sure that the gearmotor is also approved for operation with an inverter (name-
plate).
• The parameter settings made for the inverter must prevent the gear unit from being
overloaded. Refer to the nameplate for performance data permitted for the respective
gear unit.
6.6 Gear units with backstop

The purpose of a backstop is to prevent undesirable reverse rotation. During operation,
the backstop permits rotation in one specified direction of rotation only.
NOTICE
Operating the motor in the blocking direction could destroy the backstop.
• Do not start up the motor in the blocking direction. Be sure that the motor power
supply is correctly connected so that the motor rotates in the required direction.
• The backstop can be operated in blocking direction with half the output torque once
for control purposes.
CCW CW
A
CW
CCW
659173899
The direction of rotation is determined with a view to the output shaft (LSS).
• Clockwise (CW)
• Counterclockwise (CCW)
The permitted direction of rotation is indicated on the housing.

I Startup
6 Speed monitoring
0
6.7 Speed monitoring

6.7.1 WEX option standard design
The standard version of the explosion-proof AR adapter features an M12x1 thread for
mounting a voltage encoder in the motor flange of the adapter. Speed monitor and volt-
age encoder are included in the scope of delivery.
6.7.2 Manufacturer's data

Speed monitor in WEX design:
Manufacturer: Pepperl + Fuchs, Mannheim

Type: KFU8-UFC-Ex1.D
Auxiliary power: DC 20 - 90 V / AC 48 - 253 V
ATEX certification number: TÜV 99 ATEX 1471
Voltage encoder in WEXA/WEX/IGEX design:
Manufacturer: Pepperl + Fuchs, Mannheim

Type: NCB12-12GM35-N0 in accordance with DIN 19234
(NAMUR)
Housing: M12x1
ATEX certification number: TÜV 99 ATEX 1471
6.8 Installation and adjustment of the WEX speed monitor

1. Read the operating instructions of the speed monitor manufacturer before you begin
with the installation!
2. Perform the basic adjustment of the speed monitor in accordance with the operating
instructions of the speed monitor manufacturer.
The setting must cause the drive to be switched off when the actual speed falls
below 95% of the nominal speed of the motor used. Refer to the nameplate of the
drive motor for the nominal speed.
The sensor integrated in the adapter generates 1 pulse per revolution of the adapter
shaft. If the switching speed of the adapter is too low, i.e. the coupling slips, the motor
must be disconnected from the supply voltage immediately.
The cause of the problem must be eliminated and the operation of the adapter must be
stopped for at least 15 minutes before re-startup. If incorrect operation by the operating
personnel cannot be ruled out, this interval should be triggered by an automatic restart
lockout.
All installation and setting notes given below refer to the speed monitor or voltage en-
coder in WEX version.
If other speed monitors are used, they must be installed and started up according to the
manufacturer’s documentation.
The speed monitor must be located outside the potentially explosive atmosphere.

Startup I
Installation and adjustment of the WEX speed monitor
6
0
6.8.1 Installation and adjustment of the WEXA/WEX speed monitor

Relay 2 can be used for creating a warning signal or for machine control (terminal as-
signment 16-18).
The wiring diagram below shows possible wiring of the speed monitor.
BU BN
2- 1+
Ex
3
+24V
L 1 2 3
+ -
Arret
Off
DC 20-90V Aus
AC 48-253V
- + - + + - Marche
7 8 10 11 12 13 14 16 17 18 19 20 23 24 On
Ein
L1 L2 L3
0V
N
18698891
[1] Sensor + [14] Startup bypass

[3] Sensor – [23] DC 24 V voltage supply, +
[10] Relay 1 (common wiring) [24] DC 24 V voltage supply, –
[11] Relay 1 (normally open contact) [19] Auxiliary output for customer application, +
[12] Relay 1 (normally closed contact) [20] Auxiliary output for customer application, –

I Startup
6 Installation and adjustment of the WEX speed monitor
0
The following figure shows the front of the speed monitor:
18702219
LED in CHK 1 (yel- Input pulses (flashing yellow in sync),

low/red): input malfunction (flashing red), and unit malfunction (continuously red)
LED PWR (green): Voltage
LED OUT 1 (yellow): Relay 1 active
LED OUT 2 (yellow): Relay 2 active
LED OUT 3 (yellow): Transistor active
RS232: The RS 232 interface for connecting a PC for setting parameters and diagnosing
the UFC with PACTware.
Display: For showing measured values and faults and visualization in parameterization
mode

The start bypass time may not exceed 3 seconds. This setting must be carefully per-
formed and verified by a final measuring step.

Startup I
Installation and adjustment of the WEX speed monitor
6
0
6.8.2 Installation and adjustment of other speed monitors

If other speed monitors are used, they must feature an intrinsically safe sensor input
(identification color: blue) for evaluation of sensors according to DIN 19234 (NAMUR)
and be approved for use of this sensor in potentially explosive atmospheres.
INFORMATION
The voltage encoder (sensor) generally features a blue connection lead and must con-
form to DIN 19234 (NAMUR). The corresponding inspection number may be attached
to the voltage encoder or the connection lead.

I Startup
6 Installation of the voltage encoder
0
6.9 Installation of the voltage encoder

The following figure illustrates the installation of the voltage encoder and the setting of
the switching interval x.
[1]
x
[2]
[3]
[5]
18712331
[1] Adapter flange bearing cover [3] Lock nut

[2] Screw head [5] Voltage encoder
1. Rotate the output shaft of the adapter until the slotted screw head can be seen
through the tapped hole in the bearing cover.
2. Voltage encoder:
• Carefully screw it into the thread in the adapter flange [1] of the variable speed
gear unit until the voltage encoder [5] rests on the screw head [2].
• Turn the encoder back by 2 turns and secure with the lock nut [3].
The switching interval is now set to 2 mm. During operation, the voltage encoder sup-
plies 1 pulse per revolution at this switching interval.

Startup I
Installation of the voltage encoder
6
0
6.9.1 Changing switching interval x

If no circuit state change occurs at the voltage encoder (LED display) with rotating shaft
of the adapter shaft operating with switching interval x = 1 mm, the switching interval can
be changed as follows:
1. With constantly lit LED [4] of the voltage encoder, turn the voltage encoder a half
turn counterclockwise at a time and check its function.
2. It the LED is not lit [4], turn the voltage encoder clockwise by 90 degrees but no
more than one time.
NOTICE
A collision with the slotted screw heads may destroy the voltage encoder.
• Do not turn in the voltage encoder by more than half a turn
3. If a circuit change still does not occur, check the voltage supply of the voltage en-
coder using the evaluation electronics (with WEXA/WEX design).

Inspection/Maintenance
7 Preliminary work regarding gear unit inspection/maintenance
7 Inspection/Maintenance
The following gear units are lubricated for life:
• Helical gear units R07, R17, R27
• Parallel shaft helical gear unit F27
• SPIROPLAN® gear unit
Depending on external factors, the surface/corrosion protection might have to be re-
paired or renewed.
7.1 Preliminary work regarding gear unit inspection/maintenance

Observe the following notes before you start with the inspection/maintenance work.
WARNING
Risk of crushing if the drive starts up unintentionally.
• Disconnect the gearmotor from the power supply before starting work and protect
it against unintentional re-start.
WARNING
Danger of burns due to hot gear unit and hot gear unit oil.
Severe injuries.
• Let the gear unit cool down before you begin with your work.
• Only remove the oil level and oil drain plug very carefully.
NOTICE
Filling in the wrong oil may result in significantly different lubricant characteristics.
• Do not mix different synthetic lubricants and do not mix synthetic with mineral lubri-
cants.
• Mineral oil is used as standard lubricant.
NOTICE
Improper maintenance may result in damage to the gear unit.
Possible damage to property.
• Observe the notes in this chapter.
INFORMATION
The position of the oil level plug, oil drain plug and the breather valve depends on the
mounting position. Refer to the diagrams of the mounting positions. See section
"Mounting positions (page 109)".

Preliminary work regarding gear unit inspection/maintenance
7
• Strict adherence to the inspection and maintenance intervals is absolutely necessary

to ensure safe working conditions.
• Before releasing shaft connections, make sure that there are no active torsional mo-
ments present (tensions within the system).
• Prevent foreign bodies from entering the gear unit during maintenance and inspec-
tion work.
• Do not clean the gear unit with a high-pressure cleaning system as water might enter
the gear unit and the seals might be damaged.
• Perform safety and function tests following all maintenance and repair work.
7.1.1 Cleaning the gear unit

Do not use materials or procedures (e.g. compressed air) that result in processes
causing electrical charge on the coating.
7.1.2 Components made of elastomers with fluoro rubber

Under normal operating conditions and at temperatures up to 200 °C, fluoro rubber is
very stable and safe. However, when heated to more than 300 °C, e.g. by fire or the
flame of a cutting torch, it forms harmful gases and vapors as well as harmful residue.
.
CAUTION
Irritation and injuries caused by improper handling of fluoro rubber
Injuries
• Components containing fluoro rubber must be protected from excessive thermal
load or removed in order to prevent the forming of harmful gases, vapors, or resi-
due.
• Avoid inhaling the gases and vapors as well as skin and eye contact, also after the
fluoro rubber component has cooled down
The following components of R..7, F..7, K..7, S..7, and SPIROPLAN® W gear units can
contain elastomers made of fluoro rubber.
• Oil seals
• Breather valve
• Screw plugs
The user is responsible for safe handling during the service life including eco-friendly
disposal.
SEW-EURODRIVE is not responsible for damage caused by improper handling.

7 Inspection/maintenance intervals
7.2 Inspection/maintenance intervals

The following table lists the inspection and maintenance intervals:
Time interval What to do?
• Every 3 000 operating hours, at least every 6 • Check running noise for possible bearing
months damage
• Visually check the seals for leakage. Check
oil and oil level in case you suspect any leak-
ages
• For gear units with a torque arm: Check and
replace the rubber buffers, if necessary
• Every 10 000 hours of operation • Check oil and oil level
• Depending on the operating and environmental • Replace breather valve
conditions (see illustration below), at least every 3
years
• Depending on the operating and environmental • Change synthetic oil
conditions (see illustration below), at least every 5 • Replace cover plate seal
years • Replace anti-friction bearing grease (recom-
• according to oil temperature mendation)
• Replace oil seal (do not install it in the same
track)
• Varying (depending on external factors) • Touch up or renew the surfaces/anticorrosion
coating
7.3 Lubricant change intervals

The following figure shows the change intervals for standard gear units under normal
environmental conditions. Change the oil more frequently when using special versions
subject to more severe/aggressive environmental conditions!
30000
[h]
25000
[3]
20000
15000
[4]
[1]
10000
[5]
5000
0
70 80 90 100 110 115 120
[2] [°C]
[1] Operating hours [3] CLP PG

[2] Sustained oil bath temperature [4] CLP HC / HCE
• Average value per oil type at 70 °C [5] CLP / HLP / E Oil

Inspection/maintenance for the AL / AM / AQ. / EWH adapter
7
7.4 Inspection/maintenance for the AL / AM / AQ. / EWH adapter

The following table lists the obligatory intervals and the corresponding measures:
• Every 3 000 hours of operation, at least every 6 • Check running noise for possible bearing
months damage
• Visually check the adapter for leakage
• After 10 000 hours of operation • Check torsional play
• Visually check the elastic annular gear
• After 25 000 - 30 000 hours of operation • Renew the rolling bearing grease
• Replace oil seal (do not install it in the
same track)
• Change the elastic annular gear
7.5 AR adapter

• Every 3 000 operating hours, at least every 6 months • Check running noise for possible bearing
damage
• After 25 000 - 30 000 hours of operation • Renew the anti-friction bearing grease
• Replace oil seal (do not install it in the
same track)
Unit / unit part Time interval What to do? Chapter

The periods of wear are affected
by many factors and may be Inspect the friction lining See "Inspection/main-
Adapter with fric- short. and cup springs, replace tenance of the drive
tional coupling them if necessary, adjust with AR torque limiting
At least every 3 000 hours of the slip torque if too low coupling"
operation
Replace the friction lining if it lost more than 50% of its original thickness (see following
table).
New brake disk:
Type Friction lining thickness [mm]
AR71 / AR80 / AR85 / AR90 / AR95 2
AR100 / AR105 / AR112 3
AR132 / AR135 / AR145 / AR160 / AR165 /
4
AR180 / AR185 / AR195

7 AR adapter
Setting tool dimensions:

Type d l u tmax
[mm] [mm] [mm] [mm]
AR71 14 30 5 16,3
AR80 / AR85 19 40 6 21,8
AR90 / AR95 24 50 8 27,3
AR100 / AR105 / AR112 28 60 8 31,3
AR132 / AR135 / AR145 38 80 10 41,3
AR160 / AR165 42 12 45,3
110
AR180 / AR185 / AR195 48 14 51,8
7.5.1 Required tools/resources

• Standard tools
• Hook spanner
• Hydraulic press
• Puller/extractor (threaded spindle with diameter like gear unit input shaft)
• Torque wrench
7.5.2 Inspecting/replacing the friction lining, adjusting the slip torque

It is only possible to check and adjust the slip torque accurately by using a torque wrench
with an appropriate connection piece, see setting values in the following table.
[1] [2] [3] [4] [5] [6] [7] [8]
[1] Safety screw [5] Friction lining

[2] Cylinder head screw [6] Cup spring
[3] Proximity switch [7] Slotted nut
[4] Friction disk [8] Friction hub

AR adapter
7
The following figure shows the rough torque adjustment

AR71-115 AR132-195
[1]
Z [2] [4]
Z
[5]
[3]
[1] Marking [4] Markings (driving disk)

[2] Lock washer (cam) [5] Slotted nut
[3] Slotted nut
WARNING
1. Disconnect the motor/variable speed gearmotor from the adapter
2. Unscrew the safety screw [1], pull the friction hub [8] off the shaft extension
3. Clamp the friction hub [8] in a vise
4. With AR 71–115: Unscrew the lock washer [2]
With AR 132–195: Unscrew the clamping screw on the slotted round nut [7]
5. Loosen the slotted round nut until you can easily adjust the frictional coupling manu-
ally.
6. With AR 71–115:Mark the position of the slotted round nut [3]
With AR 132–195: Mark the driving disk [4]
7. Unscrew and remove the slotted round nut, remove the cup springs [6]
Note: Note the sequence of the cup springs!
8. Inspect the friction lining [5]: replace if worn.
Note: Do not allow any lubricants to get onto the friction surface – this will ir-
reparably damage the surface!
9. Inspect the cup springs [6]: replace if burned out
10.Reinstall the cup springs [6] (in the same sequence as before)
11.Screw on the slotted round nut up to the mark
12.Measuring/setting
with a torque wrench
• Connect the torque wrench to the hole in the hub
• Measure the torque (in both directions), if necessary readjust using the slotted
round nut

7 AR adapter
Rough adjustment without torque wrench

• Use the hook spanner to set the torque limiting coupling
• Slip torque according to value Z" (see the following table), calculated from the
marking
with AR 71–115: = Number of cams of the lock washer
with AR 132–195: = Number of slots in the slotted round nut
13.Secure the slotted round nut with the lock washer/clamping screw
14.Re-assemble the drive in reverse order.
AR slip torques
Cup springs No. of cams or slots "Z"
Adapter Setting
type Num Thick range 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
ber ness
mm Fig. Nm Slip torque MR in Nm
1)
1 1.0-2.0 1.0 1.4 1.6 1.8 2.0

4
AR71 0.6 2 2.1-4.0 2.1 - 2.4 2.6 3.2 3.4 3.8 4
3 3 4.1-6.0 4.1 5.0 5.8 6.0
1 1.0-2.0 1.0 1.4 1.6 2.8 2.0
4
0.6 2 2.1-4.0 2.1 - 2.4 2.6 3.2 3.4 3.8 4.0
AR80
3 3 4.1-6.0 4.1 5.0 5.8 6.0
4 0.9 2 6.1-16 6.0 8.0 9.0 10 11 12 13 14 15 16
AR85 4 2 2.0-4.0 2.0 2.4 3.0 3.6 3.8 4.0
0.6
AR90 3 3 4.1-6.0 4.1 5.0 5.8 6.0
AR95 4 0.9 2 6.1-16 6.0 8.0 9.0 10 11 12 13 14 15 16
2 1.1 3 17-24 16 20 24
AR100 6 0.7 2 5.0-13 5.0 6.0 8.0 9.0 10 11 12 13
AR105 2 14-35 14 16 17 18 20 22 23 24 26 27 28 - 30 31 32 35
AR112 2 1.45 36 41 45 48 54 58 60
3 36-80
AR115
AR132S/M 1 15-32 15 18 22 24 26 - 28 30 32
AR132ML 2 33-65 33 40 50 58 67
4 1.5
AR135 68 100 120 135
3 66-130
AR145
1 30-45 32 36 38 40 41 42 40 44 45
4 1.5
AR160 2 46-85 46 48 60 65 70 75 80 85
2 2.7 2 86-200 86 90 110 125 135 150 160 180 190 200
AR165 1 30-45 32 36 38 40 41 42 44 45
4 1.5
AR180 2 46-85 40 48 60 65 70 75 80 85
AR185 2 86-200 86 90 110 125 135 150 160 170 180 190 200
2 2.7
AR195 3 201-300 200 280 300
1) For sequence of cup springs, refer to the legend below
Fig. 1: Double alternating sequence ()()

Fig. 2: Alternating sequence ()
Fig. 3: Aligned sequence ))

Inspection/maintenance for the AD input shaft assembly
7
7.5.3 Replacing the encoder of the adapter
WARNING
1. Remove the fan guard from the driving motor
2. Remove the encoder connection
3. Loosen the lock nut on the encoder and remove the old encoder
4. Install new encoder. See section "Installing the voltage encoder" (page 82).
5. Connect the encoder to the speed/slip monitor.
6. Mount fan guard
INFORMATION
Use only OEM spare parts according to the delivered spare parts lists.
7.6 Inspection/maintenance for the AD input shaft assembly

The following table lists the obligatory intervals and the corresponding measures:
• Every 3 000 hours of operation, at least every 6 • Check running noise for possible bearing
months damage
• After 25 000 - 30 000 hours of operation • Renew the rolling bearing grease
• Replacing the oil seal

7 Inspection/maintenance for the gear unit
7.7 Inspection/maintenance for the gear unit

7.7.1 Checking the oil level and changing the oil
The procedure when checking the oil level and changing the oil depends on the following
factors:
• Gear unit type
• Size
• Mounting position
Observe the references to the respective sections as well as the following table. Refer
to chapter "Mounting Positions (page 109)" for notes on the mounting positions.
Code letter Section "Checking the oil level and changing the oil" Reference
A: • Helical gear units... (page 93)
• Parallel shaft helical gear units...
• Helical-bevel gear units...
• Helical-worm gear units...
With oil level plug
B: • Helical gear units... (page 96)
• Parallel shaft helical gear units...
• SPIROPLAN® gear units...
Without oil level plug, with cover plate
C: • S37... helical-worm gear units (page 100)
Without oil level plug and cover plate
D: • SPIROPLAN® W37 / W47... (page 103)
In mounting positions M1, M2, M3, M5, M6 with oil level plug
E: • SPIROPLAN® W37 / W47... (page 106)
In M4 mounting position without oil level plug and cover plate
Code letter for section "Checking the oil level and changing the oil"
Series Gear unit
M1 M2 M3 M4 M5 M6
R07...R27 B
R37 / R67 A
R R47 / R57 A B A
R77...R167 A
RX57...R107 A
F27 B
F
F37..F157 A
K K37...K187 A
S37 C
S
S47...S97 A
W10...W30 B
W
W37...W47 D E D

Inspection/maintenance for the gear unit
7
7.7.2 A: Helical, parallel-shaft helical, helical-bevel and helical-worm gear units with oil level plug
Checking the oil
level via the oil
level plug
CAUTION
The multi-stage gear units series:
• R../R.. in mounting position M1
• S../R.. in mounting position M3
have require a higher oil level for sufficient lubrication. This is why the provided oil level
plugs must not be used. Contact SEW-EURODRIVE!
Proceed as follows to check the oil level of the gear unit:
• Observe the notes in section "Preliminary work regarding gear unit inspection/main-
tenance" (page 84).
• Determine the position of the oil level plug and the breather valve using the mounting
position sheets. See chapter "Mounting positions" (page 109).
• Place a container underneath the oil level plug.
• Slowly remove the oil level plug. Small amounts of oil may leak out.
• Check the oil level at the oil level bore (3) with the provided oil dipstick (1).
• For the measurement, make sure that the auxiliary clip (2) of the oil dipstick (1) al-
ways points up vertically (see following figure).
3
90°
1
Ø
max.
Oil
X
min.
min. = max _ X
18634635
Max. fill level (max.): Lower edge of the oil level bore (3)
Minimum fill level (min.): Maximum fill level (max.) less the value "x" depending on
diameter (Ø) of oil level bore 3 (see following table).

Ø oil level bore Minimum fill level = x [mm] = Check mark on oil dipstick
M10 x 1 1.5
M12 x 1.5 2
M22 x 1.5 3
M33 x 2 4
M42 x 2 5
The correct minimum fill level according to the table (value "x") corresponds to the
marks on the oil dipstick (see following figure).
1,5 2 3 4 5
18637707
• Proceed as follows if the oil level is too low:

– Remove the breather valve.
– Fill in oil of the same type via the vent hole.
– Re-insert the breather valve.
• Re-insert the oil level plug.

7
Checking the oil Proceed as follows to check the oil of the gear unit:
via the oil drain
1. Observe the notes in section "Preliminary work regarding gear unit inspection/main-
plug
tenance" (page 84).
2. Determine the position of the oil drain plug using the mounting position sheets. See
chapter "Mounting positions" (page 109).
3. Remove a little oil from the oil drain plug.
4. Check the oil consistency.
– Viscosity
– If you can see that the oil is heavily contaminated, we recommend that you
change the oil even if this is outside the service intervals specified in "Inspection
and maintenance intervals" (page 86).
5. Check the oil level.
Changing the oil

via the oil drain
plug and the
breather valve
WARNING
Severe injuries.
• However, the gear unit must still be warm otherwise the high viscosity of exces-
sively cold oil will make it harder to drain the oil properly.
tenance" (page 84).
2. Determine the position of the oil drain plug, the oil level plug and the breather valve
using the mounting position sheets. See chapter "Mounting positions" (page 109).
3. Place a container underneath the oil drain plug.
4. Remove the oil level plug, the breather valve and the oil drain plug.
5. Drain all the oil.
6. Re-insert the oil drain plug.
7. Fill in new oil of the same type via the vent hole (otherwise consult the customer ser-
vice). Do not mix different synthetic lubricants.
– Fill the oil according to the quantity specified on the nameplate.
– Check the oil level at the oil level plug.
8. Re-insert the oil level plug and the breather valve.

7.7.3 B: Helical, parallel shaft helical, SPIROPLAN® gear units without oil level plug with cover plate
Checking the oil For gear units without oil level bore, the oil level is checked via the cover plate opening.
level via the cover Proceed as follows:
plate
tenance" (page 84).
2. For the cover plate to be on top, you have to set up the gear unit in the following
mounting position.
– R07 - R57 in M1 mounting position
– F27 in M3 mounting position
– W10 - W30 in M1 mounting position
3. Loosen the screws [1] of the cover plate [2] and remove the cover plate [2] and the
corresponding seal [3] (see following figure).
[1]
[2]
[3]
18643211

7
4. Determine the vertical distance "x" between oil level and sealing surface of the gear
unit housing (see following figure).
90°
18646283
5. Compare the determined value "x" to the max. distance between oil level and sealing
surface of the gear unit housing specified in the following table. Adjust the fill level if
required.
Gear unit type Max. distance x [mm] between oil level and sealing surface of the gear
unit housing for mounting position
M1 M2 M3 M4 M5 M6
2 stages 52 ± 1 27 ± 1 27 ± 1 27 ± 1 27 ± 1 27 ± 1
R07
3 stages 49 ± 1 21 ± 1 21 ± 1 21 ± 1 21 ± 1 21 ± 1
2 stages 63 ± 1 18 ± 1 46 ± 1 18 ± 1 46 ± 1 46 ± 1
R17
3 stages 58 ± 1 11 ± 2 40 ± 2 11 ± 2 40 ± 2 40 ± 2
2 stages 74 ± 1 22 ± 1 45 ± 1 22 ± 1 45 ± 1 45 ± 1
R27
3 stages 76 ± 1 19 ± 1 42 ± 1 19 ± 1 42 ± 1 42 ± 1
2 stages – – – – 39 ± 1 –
R47
3 stages – – – – 32 ± 1 –
2 stages – – – – 32 ± 1 –
R57
3 stages – – – – 28 ± 1 –
2 stages 78 ± 1 31 ± 1 72 ± 1 56 ± 1 78 ± 1 78 ± 1
F27
3 stages 71 ± 1 24 ± 1 70 ± 1 45 ± 1 71 ± 1 71 ± 1
Irrespective of mounting position

W10 12 ± 1
W20 19 ± 1
W30 31 ± 1

6. Close the gear unit after the oil level check:

• Re-attach the seal of the cover plate. Make sure that the sealing surfaces are
clean and dry.
• Screw on the cover plate. Tighten the cover screws with the rated tightening
torque according to the following table from the inside to the outside in the order
illustrated in the figure. Repeat the tightening procedure until the screws are prop-
erly tightened. Only use impulse drivers or torque wrenches in order to prevent
the cover plate from being damaged (no impact drivers).
7 8
1 2
5 6 1 2 6 8
7 5
2
3 4
1 2
1 2 1
3 4 3
3 4 4 3 5 4
5 6
A B C D E
18649739
Gear unit Fig- Retaining Rated tightening torque TN Minimum tightening torque TN
type ure thread [Nm] [Nm]
R/RF07 E M5 6 4
R/RF17/27 D
R/RF47/57 A M6 11 7
F27 B
W10 C M5 6 4
W20 C
M6 11 7
W30 A

7
via the cover plate
tenance" (page 84).
2. Open the cover plate of the gear unit according to section "Checking the oil via the
cover plate" (page 96).
3. Take an oil sample via the cover plate opening.
– Viscosity
6. Screw on the cover plate. Observe the order and the tightening torques according to
section "Checking the oil level via the cover plate" (page 96)
Checking the oil

via the cover plate
WARNING
Severe injuries.
tenance" (page 84).
cover plate" (page 96).
3. Completely drain the oil in to a vessel via the cover plate opening.
4. Fill in new oil of the same type via the cover plate opening (otherwise consult the cus-
tomer service). Do not mix different synthetic lubricants.
– Oil quantity according to the nameplate.
6. Screw on the cover plate. Observe the order and the tightening torques according to
section "Checking the oil level via the cover plate" (page 96)

7.7.4 C: S37 helical-worm gear units without oil level plug and cover plate
Checking the oil The S37 gear unit is not equipped with an oil level plug or a cover plate. This is why the
level via the screw oil level is checked via the control bore.
plug
tenance" (page 84).
2. Set up the gear unit in M5 or M6 mounting position, i.e. control bore always on top.
3. Remove the screw plug [1] (see following figure).
[1]
18655371
4. Insert the dipstick vertically via the control bore all the way to the bottom of the gear
unit housing. Pull out the dipstick vertically (see following figure).
90°
18658699

7
5. Determine the size of the section "x" of the dipstick covered with lubricant using a cal-
iper (see following figure).
18661771
6. Compare the determined value "x" to the min. value depending on the mounting po-
sition specified in the following table. Correct the fill level if required.
Oil level = wetted section x [mm] of the dipstick
Gear unit Mounting position

type M1 M2 M3 M4 M5 M6
S37 10 ± 1 24 ± 1 34 ± 1 37 ± 1 24 ± 1 24 ± 1
7. Re-insert and tighten the screw plug.

Checking the oil 1. Observe the notes in section "Preliminary work regarding gear unit inspection/main-
via the screw plug tenance" (page 84).
screw plug" (page 100).
3. Take an oil sample via the screw plug bore.
– Viscosity
Changing the oil

via the screw plug
WARNING
Severe injuries.
tenance" (page 84).
screw plug" (page 100).
3. Completely drain the oil via the screw plug bore.
4. Fill in new oil of the same type via the control bore (otherwise consult the customer
service). Do not mix different synthetic lubricants.

7
7.7.5 D: SPIROPLAN® W37/W47 in mounting positions M1, M2, M3, M5, M6 with oil level plug
Checking the oil Proceed as follows to check the oil level of the gear unit:
level via the oil
level plug
tenance" (page 84).
2. Set up the gear unit in M1 mounting position.
3. Slowly remove the oil level plug (see following figure). Small amounts of oil may leak
out.
787235211
4. Check the oil level at the oil level bore (3) with the provided oil dipstick (1).
5. For the measurement, make sure that the auxiliary clip (2) of the oil dipstick (1) al-
ways points up vertically (see following figure).
3
90°
1
Ø
max.
Oil
X
min.
min. = max _ X
18634635
Max. fill level (max.): Lower edge of the oil level bore (3)

Minimum fill level (min.): Maximum fill level (max.) less the value "x" depending on
diameter (Ø) of oil level bore 3 (see following table).
Ø oil level bore Minimum fill level = x [mm] = Check mark on oil dipstick
M10 x 1 1.5
The correct minimum fill level according to the table (value "x") corresponds to the
marks on the oil dipstick (see following figure).
1,5 2 3 4 5
6. If the oil level is too low, fill in new oil of the same type via the oil level bore until the
oil level reaches the lower edge of the bore.
7. Re-insert the oil level plug.

7
via the oil level
plug
tenance" (page 84).
2. Remove a little oil at the oil level plug.
– Viscosity
Changing the oil

via the oil level
plug
WARNING
Severe injuries.
tenance" (page 84).
2. Set up the gear unit in M5 or M6 mounting position. See chapter "Mounting posi-
tions" (page 109).
3. Place a container underneath the oil level plug.
4. Remove the oil level plugs on the A and B side of the gear unit.
6. Re-insert the lower oil level plug.
7. Fill in new oil of the same type via the upper oil level plug bore (otherwise consult the
customer service). Do not mix different synthetic lubricants.
– Check the oil level.
8. Re-insert the upper oil level plug.

7.7.6 E: SPIROPLAN® W37/W47 in M4 mounting position without oil level plug and cover plate
Checking the oil The W37/W47 gear units are not equipped with an oil level plug or a cover plate. This is
level via the screw why the oil level is checked via the control bore.
plug
tenance" (page 84).
2. Set up the gear unit in M5 or M6 mounting position.
3. Remove the screw plug.
4. Insert the dipstick vertically via the control bore all the way to the bottom of the gear
unit housing. Mark the point of the dipstick where it exits the gear unit. Pull out the
dipstick vertically (see following figure).
A B
784447371
5. Determine the section "x" between the wetted part and the marking using a caliper
(see following figure).
785020811

7
6. Compare the determined value "x" to the min. value depending on the mounting po-
sition specified in the following table. Correct the fill level if required.
Oil level = wetted section x [mm] of the dipstick
Mounting position during check
Gear unit type M5 M6
Lying on the A side Lying on the B side
W37 in M4 mounting 37 ± 1 29 ± 1
position
W47 in M4 mounting 41 ± 1 30 ± 1
position
via the screw plug
tenance" (page 84).
2. Remove a little oil at the oil screw plug.
– Viscosity
Changing the oil

via the screw plug
WARNING
Severe injuries.
tenance" (page 84).
2. Set up the gear unit in M5 or M6 mounting position. See chapter "Mounting posi-
tions" (page 109).
3. Place a container underneath the screw plug.
4. Remove the screw plugs on the A and B side of the gear unit.

6. Re-insert the lower screw plug.

7. Fill in new oil of the same type via the upper screw plug bore (otherwise consult the
customer service). Do not mix different synthetic lubricants.
– Check the oil level.
8. Re-insert the upper screw plug.
7.7.7 Replacing the oil seal
NOTICE
Oil seals with a temperature below 0 °C may get damaged during installation.
• Store oil seals at ambient temperatures over 0 °C.
• Warm up the oil seals prior to installation if required.
1. When changing the oil seal, ensure that there is a sufficient grease reservoir between
the dust lip and protective lip, depending on the type of gear unit.
2. If you use double oil seals, fill one-third of the gap with grease.
7.7.8 Gear unit coating
NOTICE
Breather valves and oil seals may be damaged during painting or re-painting.
• Thoroughly cover the breather valves and the sealing lip of the oil seals with strips
prior to painting.
• Remove the strips after painting.

Mounting Positions kVA n
Designation of the mounting positions
f 8
i
P Hz
8 Mounting Positions
8.1 Designation of the mounting positions
SEW differentiates between six mounting positions, M1 – M6. The following figure
shows the spatial orientation of the gearmotor in mounting positions M1 – M6.
M6
M6
M1 M1
M2
M2
M5 M5
M4 M4
M3 M3
R..
M6
M6 M2 M1
M2
M1
M5
M5 M4
M4
M3 M3
F..
M6
M1
M1 M6
M2 M2
M5
M5
M4
M4
K.. M3
M3
S..
W..

kVA n Mounting Positions
8 f
Churning losses
i
P Hz
8.2 Churning losses

Churning losses may occur in some mounting positions. Contact SEW-EURODRIVE
* ĺ Page XX
in case of the following combinations:
Input speed
Mounting position Gear unit type Gear unit size
[rpm]
97 – 107 > 2500
M2, M4 R
> 107 >1500
97 – 107 > 2500
F
> 107 > 1500
M2, M3, M4, M5, M6 77 – 107 > 2500
K
> 107 > 1500
S 77 – 97 > 2500
8.3 Mounting positions of SPIROPLAN® gear units
INFORMATION
SPIROPLAN® gearmotors are not dependent on the mounting position, except for
W37 – W47 in M4 mounting position. However, mounting positions M1 to M6 are also
shown for SPIROPLAN® gearmotors for a complete overview.
Important: SPIROPLAN® gearmotors of sizes W10 – W30 cannot be equipped with

breather valves, oil level plugs or drain plugs.
8.4 Key
The following table shows the symbols used in the mounting position sheets and what
they mean:
Symbol Meaning
Breather valve
Oil level plug
Oil drain plug

Helical gearmotors R
f 8
i
P Hz
8.5 Helical gearmotors R

8.5.1 R07 ... R167
* ĺ (page 110)

8 f
i
P Hz
8.5.2 RF07 ... RF167, RZ07 ... RZ87
* ĺ (page 110)

f 8
i
P Hz
8.5.3 R07F ... R87F
* ĺ (page 110)

8 f
Helical gearmotors RX
i
P Hz
8.6 Helical gearmotors RX

8.6.1 RX57 ... RX107
* ĺ (page 110)

Helical gearmotors RX
f 8
i
P Hz
8.6.2 RXF57 ... RXF107
* ĺ (page 110)

8 f
Parallel-shaft helical gearmotors F
i
P Hz
8.7 Parallel-shaft helical gearmotors F

8.7.1 F27 ... F157 / FA27B ... F157B / FH27B .. FH157B / FV27B ... FV107B
* ĺ (page 110)

f 8
i
P Hz
8.7.2 FF27 ... FF157 / FAF27 ... FAF157 / FHF27 ... FHF157 / FAZ27 ... FAZ157 / FHZ27 ... FHZ157 / FVF27
... FVF107 / FVZ27 ... FVZ107
* ĺ (page 110)

8 f
i
P Hz
8.7.3 FA27 ... FA157 / FH27 ... FH157 / FV27 ... FV107 / FT37 ... FT157
* ĺ (page 110)

Helical-bevel gearmotors K
f 8
i
P Hz
8.8 Helical-bevel gearmotors K

8.8.1 K37 ... K157 / KA37B ... KA157B / KH37B ... KH157B / KV37B ... KV107B
* ĺ (page 110)

8 f
i
P Hz
8.8.2 K167 ... K187 / KH167B ... KH187B
* ĺ (page 110)

f 8
i
P Hz
8.8.3 KF37 ... KF157 / KAF37 ... KAF157 / KHF37 ... KHF157 / KAZ37 ... KAZ157 / KHZ37 ... KHZ157 /
KVF37 ... KVF107 / KVZ37 ... KVZ107
* ĺ (page 110)

8 f
i
P Hz
8.8.4 KA37 ... KA157 / KH37 ... KH157 / KV37 ... KV107 / KT37 ... KT157
* ĺ (page 110)

f 8
i
P Hz
8.8.5 KH167 ... KH187
* ĺ (page 110)

8 f
Helical-worm gearmotors S
i
P Hz
8.9 Helical-worm gearmotors S

8.9.1 S37

f 8
i
P Hz
8.9.2 S47 ... S97
* ĺ (page 110)

8 f
i
P Hz
8.9.3 SF37 / SAF37 / SHF37

f 8
i
P Hz
8.9.4 SF47 ... SF97 / SAF47 ... SAF97 / SHF47 ... SHF97 / SAZ47 ... SAZ97 / SHZ47 ... SHZ97
* ĺ (page 110)

8 f
i
P Hz
8.9.5 SA37 / SH37 / ST37

f 8
i
P Hz
8.9.6 SA47 ... SA97 / SH47 ... SH97 / ST47 ... ST97
* ĺ (page 110)

8 f
SPIROPLAN® W gearmotors
i
P Hz
8.10 SPIROPLAN® W gearmotors

8.10.1 W10 ... W30

f 8
i
P Hz
8.10.2 WF10 ... WF30 / WAF10 ... WAF30

8 f
i
P Hz
8.10.3 WA10 ... WA30

f 8
i
P Hz
8.10.4 W37 ... W47 / WA37B ... WA47B / WH37B ... WH47B

8 f
i
P Hz
8.10.5 WF37 ... WF47 / WAF37 ... WAF47 / WHF37 ... WHF47

f 8
i
P Hz
8.10.6 WA37 ... WA47 / WH37 ... WH47 / WT37 ... WT47

kVA n Technical Data
9 f
Extended storage
i
P Hz
9 Technical Data
9.1 Extended storage
INFORMATION
For storage periods longer than 9 months, SEW-EURODRIVE recommends the "Ex-
tended storage" design. Gear units in this design are designated with a corresponding
label.
In this case, a VCI corrosion inhibitor (volatile corrosion inhibitor) is added to the lubri-
cant in these gear units. Please note that this VCI anti-corrosion agent is only effective
in a temperature range of -25 °C to +50 °C. The flange contact surfaces and shaft ends
are also treated with an anti-corrosion agent.
Observe the storage conditions specified in the following table for extended storage:
9.1.1 Storage conditions

The gear units must remain tightly sealed until taken into operation to prevent the VCI
corrosion protection agent from evaporating.
The gear units come with the oil fill according to the specified mounting position (M1 –
M6). Check the oil level before you start operating the gear unit for the first time.
Climate zone Packaging1) Storage2) Storage duration
Packed in containers, with Up to 3 years with regular
desiccant and moisture Under roof, protected against rain and snow, no checks of the packaging and
Temperate indicator sealed in the shock loads. moisture indicator (rel.
(Europe, USA, plastic wrap. humidity < 50%).
Canada, China Under roof and enclosed at constant temperature
and Russia, and atmospheric humidity (5 °C < ࢡ < 60 °C, 2 years or more with regular
excluding tropical < 50% relative humidity). inspections. Check for clean-
zones) Open liness and mechanical dam-
No sudden temperature fluctuations. Controlled age during inspection. Check
ventilation with filter (free from dust and dirt). corrosion protection.
Protected against aggressive vapors and shocks.
Packed in containers, with
desiccant and moisture
indicator sealed in the Up to 3 years with regular
plastic wrap. checks of the packaging and
With roof, protected against rain and shocks.
Tropical (Asia, moisture indicator (rel.
Protected against insect humidity < 50%).
Africa, Central damage and mildew by
and South Amer- chemical treatment.
ica, Australia,
New Zealand Under roof and enclosed at constant temperature
excluding and atmospheric humidity (5 °C < ࢡ < 50 °C, 2 years or more with regular
temperate zones) < 50% relative humidity). inspections. Check for clean-
Open No sudden temperature fluctuations. Controlled liness and mechanical dam-
ventilation with filter (free from dust and dirt). age during inspection. Check
Protected against aggressive vapors and shocks. corrosion protection.
Protected against insect damage.
1) The packaging must be carried out by an experienced company using the packaging materials that have been explicitly specified for
the particular application.
2) SEW-EURODRIVE recommends to store the gear units according to the mounting position.

Technical Data kVA n
Lubricants
f 9
i
P Hz
9.2 Lubricants
Unless a special arrangement is made, SEW-EURODRIVE supplies the drives with a
lubricant fill adapted for the specific gear unit and mounting position. The mounting po-
sition (M1 – M6, see chapter "Mounting positions") specified in the order is the basis for
this. If you change the mounting position later, you must adapt the lubricant fill quantity
accordingly.

It is essential to contact SEW-EURODRIVE regarding a subsequent change of mount-
ing position! ATEX approval will become void without prior consultation.
9.2.1 Bearing greases

The rolling bearings in gear units and motors are given a factory-fill with the greases
listed below. SEW-EURODRIVE recommends regreasing rolling bearings with a grease
fill at the same time as changing the oil.
Ambient temperature Manufacturer Type
-40 °C to +80 °C Fuchs Renolit CX-TOM 15
Gear unit rolling bearings
-40 °C to +80 °C Klüber Petamo GHY 133 N
-40 °C to +40 °C Castrol Oberen FS 2
-20 °C to +40 °C Fuchs Plantagen 2S

Oil
INFORMATION
The following grease quantities are required:
• For fast-running bearings (gear unit input end):
Fill the cavities between the rolling elements one-third full with grease.
• For slow-running bearings (gear unit output end):
Fill the cavities between the rolling elements two-thirds full with grease.

9 f
Lubricants
i
P Hz
9.2.2 Lubricant table

The lubricant table on the following page shows the permitted lubricants for SEW-
EURODRIVE explosion-proof gear units. Observe the following key to the lubricant ta-
ble.
Key to the lubricant Abbreviations, meaning of shading and notes:

table
CLP PG = Polyglycol (W gear units, conforms to USDA-H1)
CLP HC = Synthetic hydrocarbons
E = Ester oil (water hazard classification 1)
HCE = Synthetic hydrocarbons + ester oil (USDA - H1 certification)
HLP = Hydraulic oil
= Synthetic lubricant (= synthetic-based roller bearing grease)
1) Helical-worm gear units with PG oil: consult SEW-EURODRIVE.

2) Special lubricant for SPIROPLAN® gear units only
3) Recommendation: Select SEW fB 1.2
4) Observe the critical starting behavior at low temperatures.
5) Low-viscosity grease
6) Ambient temperature
7) Grease
Lubricant for the food industry (food grade oil)
Biodegradable oil (lubricant for agriculture, forestry, and water management)

Oil

6)
Oil ISO,NLGI Mobil® '6$)4

°C -50 0 +50 +100 -6#3*$"5*0/ TEXACO Tribol Optimol TO T A L
DIN (ISO) Sh ell
Standard
-20 +60 Mobil Shell Omala Klübersynth Pinnacle Tribol Optigear Renolin Unisyn
CLP HC VG 220 Synthetic X 220
R... SHC 630 S4 GX 220 GEM 4-220 N EP 220 1510/220 CLP 220
Lubricant table
4) -40 +40 Mobil Shell Omala Klübersynth Pinnacle Optigear Renolin Unisyn Carter SH
CLP HC VG 150 S4 GX 150
SHC 629 GEM 4-150 N EP 150 Synthetic X 150 CLP 150 150
K... 4) -40 +20 Mobil Shell Omala Renolin Unisyn

CLP HC VG 68
SHC 626 S4 GX 68 CLP 68
F... -40 0 Mobil Klüber-Summit Cetus Dacnis SH
4) CLP HC VG 32 Optileb HY 32 Renolin Unisyn
SHC 624 HySyn FG-32 PAO 46 OL 32 32
Standard
Mobil Shell Omala Klübersynth Pinnacle Optigear Renolin Unisyn
-20 +60 CLP HC VG 460
SHC 634 S4 GX 460 GEM 4-460 N EP 460 Synthetic X 460 CLP 460
S...(HS...)
-40 +30 Mobil Shell Omala Klübersynth Pinnacle Optigear Renolin Unisyn Carter SH
4) CLP HC VG 150 SHC 629 S4 GX 150 GEM 4-150 N EP 150 Synthetic X 150 CLP 150 150
4) -40 +20 Mobil Shell Omala Renolin Unisyn

CLP HC VG 68 S4 GX 68 CLP 68
SHC 626
-40 0 Mobil Klüber-Summit Cetus Renolin Unisyn Dacnis SH

4) CLP HC VG 32 Optileb HY 32
SHC 624 HySyn FG-32 PAO 46 OL 32 32
Standard
Klüberoil Optileb Cassida
-10 +40 CLP HC VG 460 Fluid GL 460
4UH1-460 N GT 460
NSF H1
-20 +30 VG 220
R...,K...(HK...), 4UH1-220 N GT 220 Fluid GL 220
Assembly and Operating Instructions – Explosion-Proof Gear Units

F...,S...(HS...)
4) -40 0 VG 68
4UH1-68 N HY 68 Fluid HF 68
E Shell Naturelle
-20 +40 VG 460 Klüberbio Plantogear
Gear Fluid
Oil CA2-460 460S
EP 460
Standard 1)
SEW PG VG 460 Klüber SEW
-20 +40
W...(HW...) HT-460-5
SAE 75W90 Mobil Synth

-40 +10 API GL5 Gear Oil
(~VG 100) 75 W90
CLP PG 2) Klübersynth
-20 +60 VG 460
NSF H1 UH1 6-460
Standard
-20 +80 Klübersynth
PS.F.. CLP PG VG 220 GH-6-220
CLP PG 2)
-20 +60 Klübersynth
Lubricants
Technical Data
NSF H1 VG 460
3) UH1 6-460
Mobil
i
4) -40 0 CLP HC VG 32 SHC 624

kVA
Standard
BS.F.. 4) -20 +60
Klübersynth
CLP PG VG 220
f
GH 6-220
P Hz
n
CLP PG 2) Klübersynth
-20 +60 VG 460
460 NSF UH1 6-460
017680600
3)
9007202440580747
9
139
9 f
Lubricants
i
P Hz
9.2.3 Lubricant fill quantities

Refer to the gear unit nameplate for prescribed lubricant fill quantities in explosion-proof
gear units. Check the oil level after the filling process. See section "Inspection/mainte-
nance for the gear unit" (page 92).

Malfunctions
10
10 Malfunctions
WARNING
• De-energize the motor before you start working on the unit.
• Secure the motor against unintended power-up.
CAUTION
Severe injuries.
• Let the gear unit cool down before you start working on it.
• Carefully remove the oil level plug and oil drain plug.
CAUTION
Improper handling of the gear unit and the motor may lead to damage.
• SEW drives may only be repaired by qualified personnel who are familiar with the
technical rules for industrial safety and health.
• Only qualified personnel is permitted to separate drive and motor.
• Consult SEW-EURODRIVE customer service.

Malfunctions
10 Gear unit
10.1 Gear unit

Malfunction Possible cause Remedy
Unusual, regular running Meshing/grinding noise: Bearing damage Check the oil ĺ see "Inspection/maintenance for the
noise gear unit" (page 92), change bearings.
Knocking noise: Irregularity in the gearing Contact customer service.
Unusual, irregular running Foreign bodies in the oil • Check the oil ĺ see "Inspection/maintenance for
noise the gear unit" (page 92),
• Stop the drive, contact customer service
Oil leaking Rubber seal on the gear cover plate leaking Tighten the screws on the gear cover plate and
• From inspection cover observe the gear unit. If oil still leaks: Contact customer
• From the motor flange service.
• From the motor oil seal Seal defective Contact customer service.
• From the gear unit
flange
• At output-end oil seal1) Gear unit not ventilated Vent the gear unit ĺ see "Mounting Positions"
(page 109).
Moisture film Function-related pseudo-leakage There is no fault.
• around the dust lip of Remove with soft, lint-free cloth and keep monitoring it.
the oil seal If oil leaks out after more than 168 hours of operation,
• with small trickle on the contact the customer service.
bottom end of the oil
seal in new drives dur-
ing the run-in phase2)
Drop formation and dripping Oil seal defective Check the sealing system 2)Contact customer service,
even after the run-in phase if necessary
on the output end oil seal
Oil leaking from breather Too much oil Correct the oil fill quantity ĺ see "Inspection/mainte-
valve nance for the gear unit" (page 92),
Function-related oil mist There is no fault.
Drive installed in incorrect mounting position • Properly adjust the breather valve ĺ see "Mount-
ing Positions (page 109)"
• Correct the oil level ĺ see "Inspection/mainte-
nance for the gear unit" (page 92),
Frequent cold starts (oil foams) and/or high oil Use an oil expansion tank
level
Output shaft does not turn Shaft-hub connection in the gear unit inter- Send in the gear unit/gearmotor for repair.
although the motor is rupted.
running or the input shaft is
rotated
1) Short-term oil/grease leakage at the oil seal is possible in the run-in phase (168 hours running time).
2) During the run-in phase, the sealing lip grinds on the shaft and produces a path with a smoothed surface. Once the run-in phase has
been completed, the prerequisites for proper functioning of the seal are fulfilled.

Malfunctions
AM / AQ. / AL / EWH adapter
10
10.2 AM / AQ. / AL / EWH adapter

Unusual, regular running Meshing/grinding noise: Bearing damage Contact SEW-EURODRIVE customer service
noise
Oil leaking Seal defective Contact SEW-EURODRIVE customer service
Output shaft does not turn Shaft-hub connection in the gear unit or the Send the gear unit to SEW-EURODRIVE for repair.
although the motor is run- adapter interrupted.
ning or the input shaft is
rotated
Change in running noise Annular gear wear, short-term torque transfer Change the annular gear
and/or vibrations through metal contact
Bolts to secure hub axially are loose. Tighten the screws
Premature wear in annular • Contact with aggressive fluids/oils; ozone Contact SEW-EURODRIVE customer service
gear influence; excessive ambient tempera-
tures, etc. that can change the physical
properties of the annular gear.
• Impermissibly high ambient/contact tem-
perature for the annular gear; maximum
permitted temperature: –20 °C to +80 °C
• Overload
10.3 AD input shaft assembly

Unusual, regular running Meshing/grinding noise: Bearing damage. Contact SEW-EURODRIVE customer service
noise
Output shaft does not turn Connection between shaft and hub in gear Send the gear unit to SEW-EURODRIVE for repair.
although the input shaft is unit or cover interrupted
rotated.
10.4 Adapter with a torque limiting coupling AR

Malfunction Possible causes Solution
Unusual, regular running Meshing/grinding noise: Bearing damage. Contact SEW-EURODRIVE customer service
noise
• Encoder on adapter is defective Measure input pulses, if necessary:
Evaluation unit display • Friction lining worn. • Change encoder of the adapter, see section
empty Inspection/Maintenance "Changing the pulse
encoder of the adapter".
• Friction lining worn. Inspect friction lining/cup springs, see section Inspec-
Slip torque is not reached. • Cup springs burned out or installed incor- tion/Maintenance Inspecting/replacing friction lining,
rectly after maintenance. adjusting the slip torque".

Malfunctions
10 Customer service
10.5 Customer service

Please have the following information available if you require customer service
assistance:
• Nameplate data (complete)
• Type and extent of the problem
• Time the problem occurred and any accompanying circumstances
• Assumed cause
A digital photograph if possible
10.6 Disposal
Dispose gear units in accordance with the regulations in force regarding respective ma-
terials:
• Steel scrap
– Housing parts
– Gears
– Shafts
– Roller bearing
• Parts of the worm gears are made of non-ferrous metals. Dispose of the worm gears
as appropriate.
• Collect waste oil and dispose of it according to the regulations in force.

Declarations of Conformity
Gear units in category 2G and 2D with AM / AQA / AL / AD / AR adapter
11
11 Declarations of Conformity
11.1 Gear units in category 2G and 2D with AM / AQA / AL / AD / AR adapter
EC Declaration of Conformity
Translation of the original text 900610310
SEW-EURODRIVE GmbH & Co KG

Ernst-Blickle-Straße 42, D-76646 Bruchsal
declares under sole responsibility that the
Gear units of the series R..

F..
K..
S..
W..
with mount-on components of the series AM

AQA
AL
AD
AR
variant /II2GD
Category 2G
2D
Designation II 2GD c,k T3/T200°C or

II 2GD c,k T3/T200°C X
II 2GD c,k IIB T3/T200°C or
II 2GD c,k IIB T3/T200°C X
II 2GD c,k T4/T120°C or
are in conformity with
ATEX Directive 94/9/EC 2)
Applied harmonized standards: EN 13463-1:2009

EN 13463-5:2011
EN 13463-8:2003
EN 60529:2000
2) SEW-EURODRIVE lodges the documents required by 94/9/EC, appendix VIII, with the notified body: FSA
GmbH, EU ID No.: 0588
Bruchsal 23.07.2014
Johann Soder
Place Date Managing Director Technology a) b)
a) Authorized representative for issuing this declaration on behalf of the manufacturer

b) Authorized representative for compiling the technical documents with same address as manufacturer

Declarations of Conformity
11 Gear units in category G and D with AR adapter
11.2 Gear units in category 3G and 3D with AR adapter
EC Declaration of Conformity
Translation of the original text 900580310

Ernst-Blickle-Straße 42, D-76646 Bruchsal
declares under sole responsibility that the
Gear units of the series R..

F..
K..
S..
W..
with mount-on components of the series AR
variant /II3GD
Category 3G
3D
Designation II 3GD c,k T3/T200°C or

are in conformity with
ATEX Directive 94/9/EC
Applied harmonized standards: EN 13463-1:2009

EN 13463-5:2011
EN 13463-8:2003
EN 60529:2000
Bruchsal 23.07.2014
Johann Soder
Place Date Managing Director Technology a) b)
a) Authorized representative for issuing this declaration on behalf of the manufacturer

b) Authorized representative for compiling the technical documents with same address as manufacturer

Address List
12
12 Address List
Germany
Headquarters Bruchsal SEW-EURODRIVE GmbH & Co KG Tel. +49 7251 75-0
Production Ernst-Blickle-Straße 42 Fax +49 7251 75-1970
Sales D-76646 Bruchsal http://www.sew-eurodrive.de
P.O. Box [email protected]
Postfach 3023 • D-76642 Bruchsal
Production / Indus- Bruchsal SEW-EURODRIVE GmbH & Co KG Tel. +49 7251 75-0
trial Gears Christian-Pähr-Str.10 Fax +49 7251 75-2970
D-76646 Bruchsal
Service Compe- Central SEW-EURODRIVE GmbH & Co KG Tel. +49 7251 75-1710
tence Center Ernst-Blickle-Straße 1 Fax +49 7251 75-1711
D-76676 Graben-Neudorf [email protected]
North SEW-EURODRIVE GmbH & Co KG Tel. +49 5137 8798-30
Alte Ricklinger Straße 40-42 Fax +49 5137 8798-55
D-30823 Garbsen (near Hannover) [email protected]
East SEW-EURODRIVE GmbH & Co KG Tel. +49 3764 7606-0
Dänkritzer Weg 1 Fax +49 3764 7606-30
D-08393 Meerane (near Zwickau) [email protected]
South SEW-EURODRIVE GmbH & Co KG Tel. +49 89 909552-10
Domagkstraße 5 Fax +49 89 909552-50
D-85551 Kirchheim (near München) [email protected]
West SEW-EURODRIVE GmbH & Co KG Tel. +49 2173 8507-30
Siemensstraße 1 Fax +49 2173 8507-55
D-40764 Langenfeld (near Düsseldorf) [email protected]
Electronics SEW-EURODRIVE GmbH & Co KG Tel. +49 7251 75-1780
Ernst-Blickle-Straße 42 Fax +49 7251 75-1769
D-76646 Bruchsal [email protected]
Drive Service Hotline / 24 Hour Service +49 180 5 SEWHELP
+49 180 5 7394357
14 euro cents/min on the German land-
line network. Max 42 euro cents/min
from a German mobile network. Prices
for mobile and international calls may
differ.
Additional addresses for service in Germany provided on request!
France
Production Haguenau SEW-USOCOME Tel. +33 3 88 73 67 00
Sales 48-54 route de Soufflenheim Fax +33 3 88 73 66 00
Service B. P. 20185 http://www.usocome.com
F-67506 Haguenau Cedex [email protected]
Production Forbach SEW-USOCOME Tel. +33 3 87 29 38 00
Zone industrielle
Technopôle Forbach Sud
B. P. 30269
F-57604 Forbach Cedex
Assembly Bordeaux SEW-USOCOME Tel. +33 5 57 26 39 00
Sales Parc d'activités de Magellan Fax +33 5 57 26 39 09
Service 62 avenue de Magellan - B. P. 182
F-33607 Pessac Cedex
Lyon SEW-USOCOME Tel. +33 4 72 15 37 00
Parc d'affaires Roosevelt Fax +33 4 72 15 37 15
Rue Jacques Tati
F-69120 Vaulx en Velin

Address List
12
France
Nantes SEW-USOCOME Tel. +33 2 40 78 42 00
Parc d’activités de la forêt Fax +33 2 40 78 42 20
4 rue des Fontenelles
F-44140 Le Bignon
Paris SEW-USOCOME Tel. +33 1 64 42 40 80
Zone industrielle Fax +33 1 64 42 40 88
2 rue Denis Papin
F-77390 Verneuil I'Etang
Additional addresses for service in France provided on request!
Algeria
Sales Algiers REDUCOM Sarl Tel. +213 21 8214-91
16, rue des Frères Zaghnoune Fax +213 21 8222-84
Bellevue [email protected]
16200 El Harrach Alger http://www.reducom-dz.com
Argentina
Assembly Buenos Aires SEW EURODRIVE ARGENTINA S.A. Tel. +54 3327 4572-84
Sales Centro Industrial Garin, Lote 35 Fax +54 3327 4572-21
Ruta Panamericana Km 37,5 [email protected]
1619 Garin http://www.sew-eurodrive.com.ar
Australia
Assembly Melbourne SEW-EURODRIVE PTY. LTD. Tel. +61 3 9933-1000
Sales 27 Beverage Drive Fax +61 3 9933-1003
Service Tullamarine, Victoria 3043 http://www.sew-eurodrive.com.au
[email protected]
Sydney SEW-EURODRIVE PTY. LTD. Tel. +61 2 9725-9900
9, Sleigh Place, Wetherill Park Fax +61 2 9725-9905
New South Wales, 2164 [email protected]
Austria
Assembly Wien SEW-EURODRIVE Ges.m.b.H. Tel. +43 1 617 55 00-0
Sales Richard-Strauss-Strasse 24 Fax +43 1 617 55 00-30
Service A-1230 Wien http://www.sew-eurodrive.at
[email protected]
Belarus
Sales Minsk SEW-EURODRIVE BY Tel.+375 17 298 47 56 / 298 47 58
RybalkoStr. 26 Fax +375 17 298 47 54
BY-220033 Minsk http://www.sew.by
[email protected]
Belgium
Assembly Brussels SEW-EURODRIVE n.v./s.a. Tel. +32 16 386-311
Sales Researchpark Haasrode 1060 Fax +32 16 386-336
Service Evenementenlaan 7 http://www.sew-eurodrive.be
BE-3001 Leuven [email protected]
Service Compe- Industrial Gears SEW-EURODRIVE n.v./s.a. Tel. +32 84 219-878
tence Center Rue de Parc Industriel, 31 Fax +32 84 219-879
BE-6900 Marche-en-Famenne http://www.sew-eurodrive.be
[email protected]
Brazil
Production São Paulo SEW-EURODRIVE Brasil Ltda. Tel. +55 11 2489-9133
Sales Avenida Amâncio Gaiolli, 152 - Rodovia Presi- Fax +55 11 2480-3328
Service dente Dutra Km 208 http://www.sew-eurodrive.com.br
Guarulhos - 07251-250 - SP [email protected]
SAT - SEW ATENDE - 0800 7700496

Address List
12
Brazil
Assembly Rio Claro SEW-EURODRIVE Brasil Ltda. Tel. +55 19 3522-3100
Sales Rodovia Washington Luiz, Km 172 Fax +55 19 3524-6653
Service Condomínio Industrial Conpark [email protected]
Caixa Postal: 327
13501-600 – Rio Claro / SP
Joinville SEW-EURODRIVE Brasil Ltda. Tel. +55 47 3027-6886
Rua Dona Francisca, 12.346 – Pirabeiraba Fax +55 47 3027-6888
89239-270 – Joinville / SC [email protected]
Indaiatuba SEW-EURODRIVE Brasil Ltda. Tel. +55 19 3835-8000
Estrada Municipal Jose Rubim, 205 [email protected]
Rodovia Santos Dumont Km 49
13347-510 - Indaiatuba / SP
Bulgaria
Sales Sofia BEVER-DRIVE GmbH Tel. +359 2 9151160
Bogdanovetz Str.1 Fax +359 2 9151166
BG-1606 Sofia [email protected]
Cameroon
Sales Douala Electro-Services Tel. +237 33 431137
Rue Drouot Akwa Fax +237 33 431137
B.P. 2024 [email protected]
Douala
Canada
Assembly Toronto SEW-EURODRIVE CO. OF CANADA LTD. Tel. +1 905 791-1553
Sales 210 Walker Drive Fax +1 905 791-2999
Service Bramalea, ON L6T 3W1 http://www.sew-eurodrive.ca
[email protected]
Vancouver SEW-EURODRIVE CO. OF CANADA LTD. Tel. +1 604 946-5535
Tilbury Industrial Park Fax +1 604 946-2513
7188 Honeyman Street [email protected]
Delta, BC V4G 1G1
Montreal SEW-EURODRIVE CO. OF CANADA LTD. Tel. +1 514 367-1124
2555 Rue Leger Fax +1 514 367-3677
Lasalle, PQ H8N 2V9 [email protected]
Additional addresses for service in Canada provided on request!
Chile
Assembly Santiago SEW-EURODRIVE CHILE LTDA. Tel. +56 2 75770-00
Sales Las Encinas 1295 Fax +56 2 75770-01
Service Parque Industrial Valle Grande http://www.sew-eurodrive.cl
LAMPA [email protected]
RCH-Santiago de Chile
P.O. Box
Casilla 23 Correo Quilicura - Santiago - Chile
China
Production Tianjin SEW-EURODRIVE (Tianjin) Co., Ltd. Tel. +86 22 25322612
Assembly No. 46, 7th Avenue, TEDA Fax +86 22 25323273
Sales Tianjin 300457 [email protected]
Service http://www.sew-eurodrive.cn
Assembly Suzhou SEW-EURODRIVE (Suzhou) Co., Ltd. Tel. +86 512 62581781
Sales 333, Suhong Middle Road Fax +86 512 62581783
Service Suzhou Industrial Park [email protected]
Jiangsu Province, 215021

Address List
12
China
Guangzhou SEW-EURODRIVE (Guangzhou) Co., Ltd. Tel. +86 20 82267890
No. 9, JunDa Road Fax +86 20 82267922
East Section of GETDD [email protected]
Guangzhou 510530
Shenyang SEW-EURODRIVE (Shenyang) Co., Ltd. Tel. +86 24 25382538
10A-2, 6th Road Fax +86 24 25382580
Shenyang Economic Technological Develop- [email protected]
ment Area
Shenyang, 110141
Wuhan SEW-EURODRIVE (Wuhan) Co., Ltd. Tel. +86 27 84478388
10A-2, 6th Road Fax +86 27 84478389
No. 59, the 4th Quanli Road, WEDA [email protected]
430056 Wuhan
Xi'An SEW-EURODRIVE (Xi'An) Co., Ltd. Tel. +86 29 68686262
No. 12 Jinye 2nd Road Fax +86 29 68686311
Xi'An High-Technology Industrial Development [email protected]
Zone
Xi'An 710065
Additional addresses for service in China provided on request!
Colombia
Assembly Bogotá SEW-EURODRIVE COLOMBIA LTDA. Tel. +57 1 54750-50
Sales Calle 22 No. 132-60 Fax +57 1 54750-44
Service Bodega 6, Manzana B http://www.sew-eurodrive.com.co
Santafé de Bogotá [email protected]
Croatia
Sales Zagreb KOMPEKS d. o. o. Tel. +385 1 4613-158
Service Zeleni dol 10 Fax +385 1 4613-158
HR 10 000 Zagreb [email protected]
Czech Republic
Sales Prague SEW-EURODRIVE CZ s.r.o. Tel. +420 255 709 601
Assembly Floriánova 2459 Fax +420 235 350 613
Service 253 01 Hostivice http://www.sew-eurodrive.cz
[email protected]
SEW-EURODRIVE CZ s.r.o.
Lužná 591
16000 Praha 6 - Vokovice
Drive Service HOT-LINE +420 800 739 739 (800 SEW SEW) Servis:
Hotline / 24 Hour Tel. +420 255 709 632
Service Fax +420 235 358 218
[email protected]
Denmark
Assembly Copenhagen SEW-EURODRIVEA/S Tel. +45 43 9585-00
Sales Geminivej 28-30 Fax +45 43 9585-09
Service DK-2670 Greve http://www.sew-eurodrive.dk
[email protected]
Egypt
Sales Cairo Copam Egypt Tel. +20 2 22566-299 +1 23143088
Service for Engineering & Agencies Fax +20 2 22594-757
33 EI Hegaz ST, Heliopolis, Cairo http://www.copam-egypt.com/
[email protected]

Address List
12
Estonia
Sales Tallin ALAS-KUUL AS Tel. +372 6593230
Reti tee 4 Fax +372 6593231
EE-75301 Peetri küla, Rae vald, Harjumaa [email protected]
Finland
Assembly Lahti SEW-EURODRIVE OY Tel. +358 201 589-300
Sales Vesimäentie 4 Fax +358 3 780-6211
Service FIN-15860 Hollola 2 http://www.sew-eurodrive.fi
[email protected]
Production Karkkila SEW Industrial Gears Oy Tel. +358 201 589-300
Assembly Valurinkatu 6, PL 8 Fax +358 201 589-310
FI-03600 Karkkila, 03601 Karkkila [email protected]
http://www.sew-eurodrive.fi
Gabon
Sales Libreville ESG Electro Services Gabun Tel. +241 741059
Feu Rouge Lalala Fax +241 741059
1889 Libreville [email protected]
Gabun
Great Britain
Assembly Normanton SEW-EURODRIVE Ltd. Tel. +44 1924 893-855
Sales Beckbridge Industrial Estate Fax +44 1924 893-702
Service Normanton http://www.sew-eurodrive.co.uk
West Yorkshire [email protected]
WF6 1QR
Drive Service Hotline / 24 Hour Service Tel. 01924 896911
Greece
Sales Athens Christ. Boznos & Son S.A. Tel. +30 2 1042 251-34
12, K. Mavromichali Street Fax +30 2 1042 251-59
P.O. Box 80136 http://www.boznos.gr
GR-18545 Piraeus [email protected]
Hong Kong
Assembly Hong Kong SEW-EURODRIVE LTD. Tel. +852 36902200
Sales Unit No. 801-806, 8th Floor Fax +852 36902211
Service Hong Leong Industrial Complex [email protected]
No. 4, Wang Kwong Road
Kowloon, Hong Kong
Hungary
Sales Budapest SEW-EURODRIVE Kft. Tel. +36 1 437 06-58
Service H-1037 Budapest Fax +36 1 437 06-50
Kunigunda u. 18 http://www.sew-eurodrive.hu
[email protected]
India
Registered Office Vadodara SEW-EURODRIVE India Private Limited Tel. +91 265 3045200, +91 265
Assembly Plot No. 4, GIDC 2831086
Sales POR Ramangamdi • Vadodara - 391 243 Fax +91 265 3045300, +91 265
2831087
Service Gujarat
http://www.seweurodriveindia.com
salesvadodara@seweurodrivein-
dia.com

Address List
12
India
Assembly Chennai SEW-EURODRIVE India Private Limited Tel. +91 44 37188888
Sales Plot No. K3/1, Sipcot Industrial Park Phase II Fax +91 44 37188811
Service Mambakkam Village [email protected]
Sriperumbudur - 602105
Kancheepuram Dist, Tamil Nadu
Ireland
Sales Dublin Alperton Engineering Ltd. Tel. +353 1 830-6277
Service 48 Moyle Road Fax +353 1 830-6458
Dublin Industrial Estate [email protected]
Glasnevin, Dublin 11 http://www.alperton.ie
Israel
Sales Tel-Aviv Liraz Handasa Ltd. Tel. +972 3 5599511
Ahofer Str 34B / 228 Fax +972 3 5599512
58858 Holon http://www.liraz-handasa.co.il
[email protected]
Italy
Assembly Solaro SEW-EURODRIVE di R. Blickle & Co.s.a.s. Tel. +39 02 96 9801
Sales Via Bernini,14 Fax +39 02 96 799781
Service I-20020 Solaro (Milano) http://www.sew-eurodrive.it
[email protected]
Ivory Coast
Sales Abidjan SICA Tel. +225 21 25 79 44
Société Industrielle & Commerciale pour Fax +225 21 25 88 28
l'Afrique [email protected]
165, Boulevard de Marseille
26 BP 1173 Abidjan 26
Japan
Assembly Iwata SEW-EURODRIVE JAPAN CO., LTD Tel. +81 538 373811
Sales 250-1, Shimoman-no, Fax +81 538 373855
Service Iwata http://www.sew-eurodrive.co.jp
Shizuoka 438-0818 [email protected]
Kazakhstan
Sales Almaty ɌɈɈ "ɋȿȼ-ȿȼɊɈȾɊȺɃȼ" Ɍɟɥ. +7 (727) 334 1880
ɩɪ.Ɋɚɣɵɦɛɟɤɚ, 348 Ɏɚɤɫ +7 (727) 334 1881
050061 ɝ. Ⱥɥɦɚɬɵ http://www.sew-eurodrive.kz
Ɋɟɫɩɭɛɥɢɤɚ Ʉɚɡɚɯɫɬɚɧ [email protected]
Kenya
Sales Nairobi Barico Maintenances Ltd Tel. +254 20 6537094/5
Kamutaga Place Fax +254 20 6537096
Commercial Street [email protected]
Industrial Area
P.O.BOX 52217 - 00200
Nairobi
Latvia
Sales Riga SIA Alas-Kuul Tel. +371 6 7139253
Katlakalna 11C Fax +371 6 7139386
LV-1073 Riga http://www.alas-kuul.com
[email protected]

Address List
12
Lebanon
Sales Lebanon Beirut Gabriel Acar & Fils sarl Tel. +961 1 510 532
B. P. 80484 Fax +961 1 494 971
Bourj Hammoud, Beirut [email protected]
After Sales Service [email protected]
Sales Jordan / Beirut Middle East Drives S.A.L. (offshore) Tel. +961 1 494 786
Kuwait / Saudi Ara- Sin El Fil. Fax +961 1 494 971
bia / Syria
B. P. 55-378 [email protected]
Beirut http://www.medrives.com
After Sales Service [email protected]
Lithuania
Sales Alytus UAB Irseva Tel. +370 315 79204
Statybininku 106C Fax +370 315 56175
LT-63431 Alytus [email protected]
http://www.sew-eurodrive.lt
Luxembourg
Assembly Brussels SEW-EURODRIVE n.v./s.a. Tel. +32 16 386-311
Sales Researchpark Haasrode 1060 Fax +32 16 386-336
Service Evenementenlaan 7 http://www.sew-eurodrive.lu
BE-3001 Leuven [email protected]
Madagascar
Sales Antananarivo Ocean Trade Tel. +261 20 2330303
BP21bis. Andraharo Fax +261 20 2330330
Antananarivo. [email protected]
101 Madagascar
Malaysia
Assembly Johor SEW-EURODRIVE SDN BHD Tel. +60 7 3549409
Sales No. 95, Jalan Seroja 39, Taman Johor Jaya Fax +60 7 3541404
Service 81000 Johor Bahru, Johor [email protected]
West Malaysia
Mexico
Assembly Quéretaro SEW-EURODRIVE MEXICO SA DE CV Tel. +52 442 1030-300
Sales SEM-981118-M93 Fax +52 442 1030-301
Service Tequisquiapan No. 102 http://www.sew-eurodrive.com.mx
Parque Industrial Quéretaro [email protected]
C.P. 76220
Quéretaro, México
Morocco
Sales Mohammedia SEW-EURODRIVE SARL Tel. +212 523 32 27 80/81
Service 2, rue El Jahidz Fax +212 523 32 27 89
20800 Mohammedia [email protected]
http://www.sew-eurodrive.ma
Namibia
Sales Swakopmund DB Mining & Industrial Services Tel. +264 64 462 738
Einstein Street Fax +264 64 462 734
Strauss Industrial Park [email protected]
Unit1
Swakopmund

Address List
12
Netherlands
Assembly Rotterdam SEW-EURODRIVE B.V. Tel. +31 10 4463-700
Sales Industrieweg 175 Fax +31 10 4155-552
Service NL-3044 AS Rotterdam Service: 0800-SEWHELP
Postbus 10085 http://www.sew-eurodrive.nl
NL-3004 AB Rotterdam [email protected]
New Zealand
Assembly Auckland SEW-EURODRIVE NEW ZEALAND LTD. Tel. +64 9 2745627
Sales P.O. Box 58-428 Fax +64 9 2740165
Service 82 Greenmount drive http://www.sew-eurodrive.co.nz
East Tamaki Auckland [email protected]
Christchurch SEW-EURODRIVE NEW ZEALAND LTD. Tel. +64 3 384-6251
10 Settlers Crescent, Ferrymead Fax +64 3 384-6455
Christchurch [email protected]
Norway
Assembly Moss SEW-EURODRIVE A/S Tel. +47 69 24 10 20
Sales Solgaard skog 71 Fax +47 69 24 10 40
Service N-1599 Moss http://www.sew-eurodrive.no
[email protected]
Pakistan
Sales Karachi Industrial Power Drives Tel. +92 21 452 9369
Al-Fatah Chamber A/3, 1st Floor Central Com- Fax +92-21-454 7365
mercial Area, [email protected]
Sultan Ahmed Shah Road, Block 7/8,
Karachi
Peru
Assembly Lima SEW DEL PERU MOTORES REDUCTORES Tel. +51 1 3495280
Sales S.A.C. Fax +51 1 3493002
Service Los Calderos, 120-124 http://www.sew-eurodrive.com.pe
Urbanizacion Industrial Vulcano, ATE, Lima [email protected]
Poland
Assembly Lodz SEW-EURODRIVE Polska Sp.z.o.o. Tel. +48 42 676 53 00
Sales ul. Techniczna 5 Fax +48 42 676 53 49
Service PL-92-518 àódĨ http://www.sew-eurodrive.pl
[email protected]
Service Tel. +48 42 6765332 / 42 6765343 Linia serwisowa Hotline 24H
Fax +48 42 6765346 Tel. +48 602 739 739
(+48 602 SEW SEW)
[email protected]
Portugal
Assembly Coimbra SEW-EURODRIVE, LDA. Tel. +351 231 20 9670
Sales Apartado 15 Fax +351 231 20 3685
Service P-3050-901 Mealhada http://www.sew-eurodrive.pt
[email protected]
Romania
Sales Bucharest Sialco Trading SRL Tel. +40 21 230-1328
Service str. Madrid nr.4 Fax +40 21 230-7170
011785 Bucuresti [email protected]

Address List
12
Russia
Assembly St. Petersburg ZAO SEW-EURODRIVE Tel. +7 812 3332522 +7 812 5357142
Sales P.O. Box 36 Fax +7 812 3332523
Service RUS-195220 St. Petersburg http://www.sew-eurodrive.ru
[email protected]
Senegal
Sales Dakar SENEMECA Tel. +221 338 494 770
Mécanique Générale Fax +221 338 494 771
Km 8, Route de Rufisque [email protected]
B.P. 3251, Dakar http://www.senemeca.com
Serbia
Sales Beograd DIPAR d.o.o. Tel. +381 11 347 3244 / +381 11 288
Ustanicka 128a 0393
PC Košum, IV sprat Fax +381 11 347 1337
SRB-11000 Beograd [email protected]
Singapore
Assembly Singapore SEW-EURODRIVE PTE. LTD. Tel. +65 68621701
Sales No 9, Tuas Drive 2 Fax +65 68612827
Service Jurong Industrial Estate http://www.sew-eurodrive.com.sg
Singapore 638644 [email protected]
Slovakia
Sales Bratislava SEW-Eurodrive SK s.r.o. Tel. +421 2 33595 202
Rybniþná 40 Fax +421 2 33595 200
SK-831 06 Bratislava [email protected]
http://www.sew-eurodrive.sk
Žilina SEW-Eurodrive SK s.r.o. Tel. +421 41 700 2513
Industry Park - PChZ Fax +421 41 700 2514
ulica M.R.Štefánika 71 [email protected]
SK-010 01 Žilina
Banská Bystrica SEW-Eurodrive SK s.r.o. Tel. +421 48 414 6564
Rudlovská cesta 85 Fax +421 48 414 6566
SK-974 11 Banská Bystrica [email protected]
Košice SEW-Eurodrive SK s.r.o. Tel. +421 55 671 2245
Slovenská ulica 26 Fax +421 55 671 2254
SK-040 01 Košice [email protected]
Slovenia
Sales Celje Pakman - Pogonska Tehnika d.o.o. Tel. +386 3 490 83-20
Service UI. XIV. divizije 14 Fax +386 3 490 83-21
SLO - 3000 Celje [email protected]
South Africa
Assembly Johannesburg SEW-EURODRIVE (PROPRIETARY) LIMITED Tel. +27 11 248-7000
Sales Eurodrive House Fax +27 11 494-3104
Service Cnr. Adcock Ingram and Aerodrome Roads http://www.sew.co.za
Aeroton Ext. 2 [email protected]
Johannesburg 2013
P.O.Box 90004
Bertsham 2013

Address List
12
South Africa
Cape Town SEW-EURODRIVE (PROPRIETARY) LIMITED Tel. +27 21 552-9820
Rainbow Park Fax +27 21 552-9830
Cnr. Racecourse & Omuramba Road Telex 576 062
Montague Gardens [email protected]
Cape Town
P.O.Box 36556
Chempet 7442
Cape Town
Durban SEW-EURODRIVE (PROPRIETARY) LIMITED Tel. +27 31 700-3451
2 Monaco Place Fax +27 31 700-3847
Pinetown [email protected]
Durban
P.O. Box 10433, Ashwood 3605
Nelspruit SEW-EURODRIVE (PTY) LTD. Tel. +27 13 752-8007
7 Christie Crescent Fax +27 13 752-8008
Vintonia [email protected]
P.O.Box 1942
Nelspruit 1200
South Korea
Assembly Ansan SEW-EURODRIVE KOREA CO., LTD. Tel. +82 31 492-8051
Sales B 601-4, Banweol Industrial Estate Fax +82 31 492-8056
Service #1048-4, Shingil-Dong, Danwon-Gu, http://www.sew-korea.co.kr
Ansan-City, Kyunggi-Do Zip 425-839 [email protected]
Busan SEW-EURODRIVE KOREA Co., Ltd. Tel. +82 51 832-0204
No. 1720 - 11, Songjeong - dong Fax +82 51 832-0230
Gangseo-ku [email protected]
Busan 618-270
Spain
Assembly Bilbao SEW-EURODRIVE ESPAÑA, S.L. Tel. +34 94 43184-70
Sales Parque Tecnológico, Edificio, 302 Fax +34 94 43184-71
Service E-48170 Zamudio (Vizcaya) http://www.sew-eurodrive.es
[email protected]
Swaziland
Sales Manzini C G Trading Co. (Pty) Ltd Tel. +268 2 518 6343
PO Box 2960 Fax +268 2 518 5033
Manzini M200 [email protected]
Sweden
Assembly Jönköping SEW-EURODRIVE AB Tel. +46 36 3442 00
Sales Gnejsvägen 6-8 Fax +46 36 3442 80
Service S-55303 Jönköping http://www.sew-eurodrive.se
Box 3100 S-55003 Jönköping [email protected]
Switzerland
Assembly Basel Alfred lmhof A.G. Tel. +41 61 417 1717
Sales Jurastrasse 10 Fax +41 61 417 1700
Service CH-4142 Münchenstein bei Basel http://www.imhof-sew.ch
[email protected]
Thailand
Assembly Chonburi SEW-EURODRIVE (Thailand) Ltd. Tel. +66 38 454281
Sales 700/456, Moo.7, Donhuaroh Fax +66 38 454288
Service Muang [email protected]
Chonburi 20000

Address List
12
Tunisia
Sales Tunis T. M.S. Technic Marketing Service Tel. +216 79 40 88 77
Zone Industrielle Mghira 2 Fax +216 79 40 88 66
Lot No. 39 http://www.tms.com.tn
2082 Fouchana [email protected]
Turkey
Assembly Istanbul SEW-EURODRIVE Tel. +90-262-9991000-04
Sales Hareket Sistemleri Sanayi Ticaret Limited Fax +90-262-9991009
Service ùirketi http://www.sew-eurodrive.com.tr
Gebze Organize Sanayi Bölgesi 400.Sokak [email protected]
No:401
TR-41480 Gebze KOCAELø
Ukraine
Assembly Dnipropetrovsk ɈɈɈ «ɋȿȼ-ȿɜɪɨɞɪɚɣɜ» Ɍɟɥ. +380 56 370 3211
Sales ɭɥ.Ɋɚɛɨɱɚɹ, 23-B, ɨɮɢɫ 409 Ɏɚɤɫ. +380 56 372 2078
Service 49008 Ⱦɧɟɩɪɨɩɟɬɪɨɜɫɤ http://www.sew-eurodrive.ua
[email protected]
United Arab Emirates

Sales Sharjah Copam Middle East (FZC) Tel. +971 6 5578-488
Service Sharjah Airport International Free Zone Fax +971 6 5578-499
P.O. Box 120709 [email protected]
Sharjah
USA
Production Southeast SEW-EURODRIVE INC. Tel. +1 864 439-7537
Assembly Region 1295 Old Spartanburg Highway Fax Sales +1 864 439-7830
Sales P.O. Box 518 Fax Manufacturing +1 864 439-9948
Service Lyman, S.C. 29365 Fax Assembly +1 864 439-0566
Fax Confidential/HR +1 864 949-5557
http://www.seweurodrive.com
[email protected]
Assembly Northeast SEW-EURODRIVE INC. Tel. +1 856 467-2277
Sales Region Pureland Ind. Complex Fax +1 856 845-3179
Service 2107 High Hill Road, P.O. Box 481 [email protected]
Bridgeport, New Jersey 08014
Midwest Region SEW-EURODRIVE INC. Tel. +1 937 335-0036
2001 West Main Street Fax +1 937 332-0038
Troy, Ohio 45373 [email protected]
Southwest SEW-EURODRIVE INC. Tel. +1 214 330-4824
Region 3950 Platinum Way Fax +1 214 330-4724
Dallas, Texas 75237 [email protected]
Western Region SEW-EURODRIVE INC. Tel. +1 510 487-3560
30599 San Antonio St. Fax +1 510 487-6433
Hayward, CA 94544 [email protected]
Additional addresses for service in the USA provided on request!
Venezuela
Assembly Valencia SEW-EURODRIVE Venezuela S.A. Tel. +58 241 832-9804
Sales Av. Norte Sur No. 3, Galpon 84-319 Fax +58 241 838-6275
Service Zona Industrial Municipal Norte http://www.sew-eurodrive.com.ve
Valencia, Estado Carabobo [email protected]
[email protected]

Address List
12
Vietnam
Sales Ho Chi Minh City All sectors except harbor, steel, coal power Tel. +84 8 8301026
and offshore: Fax +84 8 8392223
Nam Trung Co., Ltd [email protected]
250 Binh Duong Avenue, Thu Dau Mot Town, [email protected]
Binh Duong Province [email protected]
HCM office: 91 Tran Minh Quyen Street
District 10, Ho Chi Minh City
Harbor and offshore: Tel. +84 8 62969 609
DUC VIET INT LTD Fax +84 8 62938 842
Industrial Trading and Engineering Services [email protected]
A75/6B/12 Bach Dang Street, Ward 02,
Tan Binh District, 70000 Ho Chi Minh City
Coal power and steel: Tel. +84 835170381
Thanh Phat Co Ltd Fax +84 835170382
DMC Building, L11-L12, Ward3, [email protected]
Binh Thanh Dist, Ho Chi Minh City
Hanoi Nam Trung Co., Ltd Tel. +84 4 37730342
R.205B Tung Duc Building Fax +84 4 37762445
22 Lang ha Street [email protected]
Dong Da District, Hanoi City
Zambia
Sales Kitwe EC Mining Limited Tel. +260 212 210 642
Plots No. 5293 & 5294,Tangaanyika Road, Off Fax +260 212 210 645
Mutentemuko Road, [email protected]
Heavy Industrial Park, http://www.ecmining.com
P.O.BOX 2337
Kitwe

Index
Index
A Embedded safety notes ...........................................6

AD input shaft assembly ........................................67 Encoder
Adapter Installation..........................................................82
AM......................................................................59 Extended storage.................................................136
AQ......................................................................63
AR ......................................................................87 F
Ambient conditions.................................................28 Flatness errors.......................................................23
Ambient temperature .............................................34 Fluorocarbon rubber ..............................................28
Assembling input and output elements ..................32
Auxiliary means......................................................21 G
Gear unit
B Cleaning.............................................................85
Backstop ................................................................77 Installation..........................................................23
Bearing greases ...................................................137 With solid shaft ..................................................31
Gear unit design
C Helical gear units ...............................................13
Changing the mounting position ............................24 Helical-worm gear units .....................................16
Changing the oil .....................................................92 SPIROPLAN® W10-W30 gear units ..................17
Check list ...............................................................11 Gear unit mounting ................................................26
Checking the oil .....................................................92 Gear unit painting ..................................................31
Checking the oil level .............................................92 Gear unit structure .................................................13
Via oil level plug ...............................................103 Helical-bevel gear unit .......................................15
Via the cover plate .............................................96 Parallel-shaft helical gear unit............................14
Via the screw plug....................................100, 106 SPIROPLAN® W37-W47 gear units ..................18
Churning losses ...................................................110 Gear units
Coating Category II2GD..................................................34
Gear unit ..........................................................108 Coating ............................................................108
Copyright..................................................................7 General safety notes................................................8
Corrosion, electrochemical.....................................24 Grease filling........................................................137
Coupling of AM adapter .........................................59
Coupling of AQ adapter .........................................63 H
Cover, installation ..................................................57 Helical gear units ...................................................13
Customer service .................................................144 Helical-bevel gear unit ...........................................15
Helical-worm gear units .........................................16
D
Design I
Helical gear units ...............................................13 Inspection ..............................................................84
Helical-worm gear units .....................................16 Changing the Oil ................................................92
SPIROPLAN® W10-W30 gear units...................17 Checking the oil .................................................92
Disposal ...............................................................144 Checking the oil level.........................................92
Documentation, applicable.....................................10 Inspection intervals ................................................86
Inspection work
E AD input shaft assembly ....................................91
Efficiency................................................................76 AL /AM / AQ. / EWH adapter .............................87
Elastomers .............................................................28 Gear unit ............................................................92

Index
Installation O
Mechanical.........................................................21 Oil level ..................................................................74
Installation tolerances ............................................21 Oil temperature ...................................................... 75
Inverter operation ...................................................77 Other applicable documentation ............................10
Inverter-operated gearmotors ................................77
P
L Painting the gear unit.............................................31
Leakage .................................................................76 Parallel-shaft helical gear unit................................14
Lubricant change intervals .....................................86 Protective cover, installation ..................................57
Pseudo-leakage.....................................................76
M
Maintenance ..........................................................84 R
Changing the oil .................................................92 Repair ..................................................................144
Checking the oil .................................................92 Run-in period .........................................................76
Checking the oil level .........................................92
Maintenance intervals ............................................86 S
Maintenance work Safety Notes
AD input shaft assembly ....................................91 Structure of the embedded ..................................6
AL /AM / AQ. / EWH adapter .............................87 Structure of the section-related............................6
Gear unit ............................................................92 Safety notes.............................................................8
Malfunctions .........................................................141 Designation in the documentation .......................6
AD input shaft assembly ..................................143 General information .............................................8
AM / AQ / AL adapter / AL / EWH ....................143 Transport ...........................................................10
Gear unit ..........................................................142 Seals......................................................................76
Mechanical Installation...........................................21 Section-related safety notes ....................................6
Motors Service................................................................. 144
Operated on the supply system .........................77 Shaft-mounted gear unit ........................................36
Motors operated on the supply system ..................77 TorqLOC® ..........................................................50
Mounting device .....................................................32 Shaft-mounted gear units
Mounting positions ...............................................109 Keyway ..............................................................39
Designation ......................................................109 Shrink disk .........................................................46
Helical gearmotors R .......................................111 Splined hollow shaft...........................................39
Helical gearmotors RX .....................................114 Signal words in the safety notes ..............................6
Helical-bevel gearmotors K..............................119 Solid shaft
Helical-worm gearmotors S..............................124 Gear units with...................................................31
Key...................................................................110 Speed monitor WEX ..............................................65
Parallel shaft helical gearmotors F...................116 Speed monitoring WEX .........................................78
SPIROPLAN® gear units .................................110 SPIROPLAN® gear units
SPIROPLAN® W gearmotors...........................130 Mounting positions...........................................110
Symbols ...........................................................110 SPIROPLAN® W10-W30 gear units ......................17
Mount-on gear unit .................................................29 SPIROPLAN® W37-W47 gear units ......................18
Stand-alone gear unit ............................................77
N Structure
Nameplate..............................................................19 Helical-bevel gear unit .......................................15
Special marking .................................................19 Parallel-shaft helical gear unit............................14
Notes SPIROPLAN® W37-W47 gear units ..................18
Designation in the documentation........................6 Surface temperature ..............................................75

Index
T Transport ...............................................................10
Technical data......................................................136 Type designation .............................................19, 20
Temperature ..........................................................34
Tightening torques .................................................25 V
Tools ......................................................................21 Ventilation ..............................................................29
TorqLOC® ..............................................................50 Voltage encoder.....................................................82
Torque arms...........................................................36
Torque arms for shaft-mounted gear units.............36 W
Helical-bevel gear units......................................37 WEX speed monitor...............................................65
Helical-worm gear units .....................................37 WEX speed monitoring ..........................................78
Parallel shaft helical gear units ..........................36
SPIROPLAN® W gear units ...............................38

SEW-EURODRIVE—Driving the world
SEW-EURODRIVE
Driving the world

P.O. Box 3023
D-76642 Bruchsal/Germany
Phone +49 7251 75-0
Fax +49 7251 75-1970
[email protected]
www.sew-eurodrive.com

Sew Motor Maintenance

Uploaded by

Copyright:

Available Formats

Sew Motor Maintenance

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Sew Motor Maintenance

Uploaded by

Copyright:

Available Formats

What are the main components of a gear unit?

What are the main components of a gear unit?

What are the main types of gear units described in the documentation?

What are the main types of gear units described in the documentation?

Drive Technology \ Drive Automation \ System Integration \ Services

Assembly and Operating Instructions

Explosion-Proof Gear Units

Edition 09/2012 20050542 / EN

Assembly and Operating Instructions – Explosion-Proof Gear Units 3

4 Assembly and Operating Instructions – Explosion-Proof Gear Units

11 Declarations of Conformity ............................................................................ 145

Assembly and Operating Instructions – Explosion-Proof Gear Units 5

1.2 Structure of the safety notes

1.2.2 Structure of the section-related safety notes

1.2.3 Structure of the embedded safety notes

6 Assembly and Operating Instructions – Explosion-Proof Gear Units

1.3 Rights to claim under warranty

1.4 Exclusion of liability

1.6 Product names and trademarks

Assembly and Operating Instructions – Explosion-Proof Gear Units 7

2.1 Preliminary information

2.2 General information

8 Assembly and Operating Instructions – Explosion-Proof Gear Units

2.3 Target group

2.4 Designated use

NOTE ON EXPLOSION PROTECTION

Assembly and Operating Instructions – Explosion-Proof Gear Units 9

2.5 Other applicable documentation

10 Assembly and Operating Instructions – Explosion-Proof Gear Units

Assembly and Operating Instructions – Explosion-Proof Gear Units 11

3.2 During startup

12 Assembly and Operating Instructions – Explosion-Proof Gear Units

4 Gear Unit Structure

4.1 Basic design of helical gear units

[1] Pinion [19] Key [42] Roller bearing [507] Shim

Assembly and Operating Instructions – Explosion-Proof Gear Units 13

4.2 Basic structure of parallel shaft helical gear units

[2] [45] [20]

14 Assembly and Operating Instructions – Explosion-Proof Gear Units

4.3 Basic structure of helical-bevel gear units

[1] Pinion [25] Rolling bearing [102] Seal [522] Shim

Assembly and Operating Instructions – Explosion-Proof Gear Units 15

4.4 Basic design of helical-worm gear units

[1] Pinion [20] Breather valve [88] Circlip [518] Shim

16 Assembly and Operating Instructions – Explosion-Proof Gear Units

4.5 Basic design of SPIROPLAN® W10-W30 gear units

[1] Pinion [19] Key [88] Circlip [251] Circlip

Assembly and Operating Instructions – Explosion-Proof Gear Units 17

4.6 Basic design of SPIROPLAN® W37 gear units

18 Assembly and Operating Instructions – Explosion-Proof Gear Units

4.7 Nameplate and type designation

na r/min 40 ne max r/min 1380 fB 3,1

RF47/A/II2GD Made in Germany

CLP HC 220 Synth. Öl / 0,65l 0641 543 1

NOTE ON EXPLOSION PROTECTION

Assembly and Operating Instructions – Explosion-Proof Gear Units 19

4.7.2 Type designation

NOTE ON EXPLOSION PROTECTION

For direct motor mounting

Gear unit size

• Gear unit size 67: Max. 0.4 mm