Progressive Agriculture 27 (3): 383-391, 2016 ISSN: 1017 - 8139

Use of waste plastic aggregation in concrete as a constituent material

MB Hossain, P Bhowmik, KM Shaad
Department of Farm Structure & Environmental Engineering, Bangladesh Agricultural University,
Mymensingh 2202, Bangladesh

Abstract
The amount of Plastics consumed annually has been growing increasingly in Bangladesh. Consequently, waste
plastic recycling has become one of the major challenges in recent times. The present study has selected waste PET,
a polymer compound of Polyethylene Terephthalate, to investigate its possible use as plastic aggregate in concrete
application. The shredded waste plastic was used in concrete with partial replacement of 5%, 10% and 20% by
volume of conventional coarse aggregate. Four types of concrete specimens including one without plastic aggregate,
for comparison purpose, were prepared. All the concrete specimens were tested for its different mechanical
properties after a curing period of 7, 21 and 28 days. Various physical properties of all aggregates and fresh concrete
properties were also tested in the laboratory. The specific gravity of waste plastic aggregate was found 1.4 and the
maximum density of concrete containing plastic aggregate was 115 lb/ft3. The density of concrete specimens
containing plastic aggregate decreased with the addition of more amount of plastic aggregate. It was found that the
concrete specimen containing waste PET at 10% volume showed higher compressive strength and higher modulus
of elasticity than other specimens. The splitting tensile strength was about 8-11% of compressive strength. The
flexural strength of concrete specimens containing plastic aggregate was lower than that of concrete without plastic
aggregate. It was found that the strength of concrete containing PET aggregate falls in the category of lightweight
concrete in terms of their strength, specific gravity and density. Thus, the waste PET aggregate could be effectively
used to reduce the unit weight of concrete which results in a reduction in the dead weight of a structural concrete.
Furthermore, it is concluded that the use of waste PET in concrete provides some advantages such as reduction in
the use of conventional aggregate, disposal of wastes, prevention of environmental pollution, and energy saving.

Key words: Waste plastic, pet aggregate, lightweight concrete, mechanical properties, stress-strain behavior

Progressive Agriculturists. All rights reserve *Corresponding Author: [email protected]

Introduction
Plastics have become an inseparable and integral part flood prevention, preservation and distribution of food,
of our lives. Its low density, strength, user-friendly housing, communication materials, security systems,
designs, fabrication capabilities, long life, light weight, and other uses. With so large and varying applications,
and low cost are the factors behind such phenomenal plastics contribute to an ever increasing volume in the
growth. Plastics have been used in packaging, solid waste stream. The production and consumption of
automotive and industrial applications, medical plastic and the rate at which solid plastic waste (SPW)
delivery systems, artificial implants, other healthcare is created have increased considerably since the first
applications, water desalination, land/soil conservation, industrial scale production of synthetic polymers

383
 Use of waste plastic aggregation in concrete

(plastics) in the 1940s. According to the Central which affected the strength characteristics
Pollution Control Board, the world produces nearly significantly.
150 million tonnes of plastics per year, which is nearly
Frigione (2010) attempted to substitute 5% by weight
4.8 tonnes per second and a per capita production of 25
of fine aggregate (natural sand) with an equal weight of
kg/year (Al-Salem et al. 2009). In Bangladesh, due to
PET aggregates manufactured from the waste un-
the rapid increase in the use of PET bottles, solid waste
washed PET bottles (WPET), in concrete. The
problem is raised. It is known that a long time (more
specimens were made with different cement content
than a hundred years) is needed to degrade the waste
and water/cement ratio. Rheological characterization
PET bottles in the nature (Silva et al., 2005). In recent
on fresh concrete and mechanical tests at the ages of 28
times, waste plastic recycling has become one of the
and 365 days were performed on the WPET/concretes
major challenges in Bangladesh (Islam, 2011). At
as well as on reference concretes containing only
present there are many plastic industries in our country.
natural fine aggregate in order to investigate the
They are using a huge number of plastics for recycling
influence of the substitution of WPET to the fine
and many other purposes.
aggregate in concrete. He found that the WPET
Different forms of the common materials, using waste concretes display similar workability characteristics,
plastic granules as lightweight aggregate in the compressive strength and splitting tensile strength
production of lightweight concrete has attracted much slightly lower than that of the reference concrete and a
attention from the researchers. Lightweight aggregates moderately higher ductility.
are generally used to reduce the unit weight of concrete
The present work attempted to utilize the waste PET
by replacing the conventional aggregates. Nowadays,
aggregate as partial replacement of conventional coarse
there are many lightweight concrete applications made
aggregate in making concrete. Various physical and
with natural or artificial lightweight aggregates are
mechanical properties of concrete have been evaluated
found in the literature. Several researches have been
incorporating different percentage of plastic aggregate
carried out to investigated the use of recycled
by volume. The influences of plastic aggregate on
Polyethylene Therephtalate (PET) as light aggregate,
concrete properties have also been analyzed and
such as Rebeiz et al. (1991), Rossignolo and Agnesini
discussed.
(2002), Silva et al. (2005), Marzouk et al. (2007) and
Choi et al. (2005). Koide et al. (2002) used PET and Materials and Methods
other plastic wastes (PE and PP) together in concrete
Waste Plastic Aggregate
by partially replacing with mineral aggregates. Albano
et al. (2009) determined the mechanical behavior of The plastic aggregates were produced mainly from
concrete containing waste PET, varying the waste PET bottles (Figure 1). The plastic bottles were
water/cement ratio from 0.50 to 0.60, PET aggregate crushed and cut into small pieces using a crushing
content (10 and 20 % by volume) and the particle sizes machine. The plastic aggregates were washed properly
of 2.6mm and 11.4mm. The results found that, as the to make them clean and to ensure that no other dust
volume proportion and the particle size of PET particles were present there (Figure 2).
aggregate increased, the concrete showed a decrease in Polyethylene terephthalate (PET) is thermoplastic
compressive strength, splitting tensile strength, polyester with tensile and flexural modulus of elasticity
modulus of elasticity and ultrasonic pulse velocity. of about 2.9 and 2.4GPa, respectively, tensile strength
Moreover, the water absorption was increased. It was up to 60 MPa and excellent chemical resistance. It is a
reported that the concrete specimens were not fully semi-crystalline polymer, with a melting point of about
compacted and showed the formation of honeycombs 260°C and a glass transition temperature ranging from

384
 Hossain et al. (2016), Progressive Agriculture 27 (3): 383-391

70 to 80°C, in relation to the amount of crystalline coarse aggregates was accomplished by sieve analysis
region enclosed in the amorphous phase. The specific method. The specific gravity and water absorption tests
gravity is around 1.3-1.4 g/cm3 (Van Krevelen, 1990). of fine and coarse aggregates were determined
In this study, the specific gravity of plastic aggregate according to ASTM C127 and C128 standards. The
used was found to be 1.4 g/cm3. The sizes of plastic physical properties of fine and coarse aggregates are
aggregate were taken between 4.75 to 9.5 mm. The shown in Table 1.
grading of the plastic aggregate is presented in Figure 3.
100

80

% passing
60

40

20

0
0.1 1 10
plastic size (mm)

Figure 3. Particle size distribution of plastic aggregate

Figure 1. Waste PET bottles at a dumping site. Table 1. Physical properties of aggregates

Properties of Fine Coarse

aggregates aggregate aggregate
Bulk specific gravity
1.22 1.42
(oven dry)
Bulk specific gravity
- 1.45
(SSD condition)
Apparent specific
1.19 1.50
gravity
Water absorption (%) - 9.30
Size range (mm) <4.75 4.75-9.5
Fineness modulus 1.97 -

Preparation of concrete specimens

Mix design of concrete was performed according to

Figure 2. Waste PET aggregate British (DOE) method (Nevile, 1981). The aggregates
were in saturated and surface-dry (SSD) conditions,
Fine and Coarse Aggregates such as all the pores in the aggregates were full and
cannot absorb water from the fresh mix. The coarse
Readily available natural river sand of Fineness
aggregate was replaced by 5%, 10% and 20% volume
Modulus 1.97 was used as fine aggregate. Brick chips
of concrete mix with the plastic aggregates. Four types
were used as coarse aggregate. Gradation of fine and

385
 Use of waste plastic aggregation in concrete

of concrete specimens were prepared maintaining the found that the percentage of water absorption was
same water:cement ratio of 0.45. The specimens were increased with the addition of plastic aggregate. For
designated as C0PA, C5PA, C10PA and C20PA having concrete specimen containing 20% volume of plastic,
0%, 5%, 10% and 20% plastic aggregate by volume water absorption was higher than that of the specimen
respectively. The densities of fresh mix concrete were without plastic aggregate.
measured immediately after each mixing. A cone of 12
inch height and 6 inch diameter was used to measure 7 days 21 days 28 days
the slump. After 24 hours of casting, all the specimens 12

Water absorption (%)

were transferred into a curing tank at room temperature 9
till the day before testing.
6
Laboratory Testing Methods
3
The tests of Compressive strength, Tensile strength,
Moduluous of elasticity, Flexural strength and 0
Shrinkage were performed according to ASTM C39, 0% plastic 5% plastic 10% 20%
ASTM C496, ASTM C469, ASTM C78 and IS:1199- plastic plastic
1959 standards, respectively. Figure 4 shows the Amount of plastic (%)
machine used in the laboratory. The load was applied
continuously until the specimen failed. The load and Figure 5. Water absorption of the specimens containing
deformation were measured at a fixed interval. plastic aggregate

According to Albano et al. (2009), this behavior is

caused since the aggregate can influence on the
porosity in two ways: one, providing a proper porosity,
and the other, altering the paste. In other words, when
substituting part of the natural fine aggregate by PET
(with a different granulometry), the latter creates a
proper and different porosity to that one created by the
sand since its shape is plane and elongated. ACI
Committee (1987) definition states that the air dry unit
weight of a structural lightweight concrete should be
lower than 1850 kg/m3.

Compressive and Tensile Strength

The compressive strength of the reference concrete

specimen and other specimens containing 5, 10 and
Figure 4. Compression testing machine used in the 20% of plastic aggregate was determined at 7, 21 and
study 28 days of curing. Figure 6 shows the results of
Results and Discussion compression tests on various concrete specimens. From
Figure 6, an accelerated increase in resistance can be
Water absorption and unit weight
noticed and the strength value of concrete containing
10% plastic was about similar to 0% plastic cylinder at
The percentages of water absorption of various
21 and 28 days. It can also be seen that the PET
concrete specimens are presented in Figure 5. It was

386
 Hossain et al.
a (2016), Progressive Agriculture 27 (3): 383-391

addition decreased the concrete resistance when concrete specimens containing 5%, 10% and 20%
compared to the fresh concrete at different curing ages, plastic are presented in Figure 7.
since the recycled PET does not contribute to the
The splitting tensile strength was evaluated at 7, 21 and
strength of the concrete as does the natural fine
28 days of cure. It is seen that the nature of increasing
aggregates (Neville, 1981). However, even though
tensile strength is similar to the compressive strength,
there is a loss in strength, the blends with 10% plastic
attributing it to the same reasons mentioned above.
presented a high grade of compressive strength. The
There is a decrease in the splitting
tting tensile strength with
compressive strength value for 10% plastic content
respect to the fresh concrete independently on the size
specimen was found about 2400psi at 28days (Figure
of the PET aggregate added. However, when the
6). According to ACI (1987),
87), the compressive strength
amount of recycled PET is 20%, the decrease is more
of a structural lightweight concrete at 28 days should
significant as a consequence of the great porosity the
be within 2200–2500psi.
concrete can have with ith this amount of PET. On the
other hand, Sakr and El-HakimHakim (2005) indicated that
0% plastic 5% plastic
the variation in the mechanical properties analyzed can
10% plastic 20% plastic
be attributed to the difference in shape and stiffness of
2800
Compressive strength (psi)

the aggregate, since the PET has a plane and angular

2100 shape with smooth characteristics, different from the
sand, which is round and stiff.
1400

700

0
5 15 25 35
Age (days)
Figure 6. Compressive strength of the concrete
specimens containing different percentage
of plastic aggregate

Albano et al. (2009) found that the standard strength

values for concretes with moderate resistance lies Figure 7. Tensile strength of the specimens containing
between 21 and 30 MPa for a curing age of 28 days. different percentage of plastic aggregate
Similar behavior was observed by Rebeiz and Fowler
(1996) and Rossignolo and Agnesini (2002), when they Stress-strain behavior
added recycled
ycled PET and rubber particles to concrete, The stress-strain behavior of fresh concrete specimen
respectively. The factors that may be responsible for and other specimens containing 5%, 10%, 20% plastic
low compressive strength of concrete containing plastic was observed at 7 , 21 and 28 days of curing. From
aggregate are: (1) the very low bond strength between Figure 8, it was seen that the stress was decreasing as
the surface of the plastic aggregate and the cement
cem the increasing of strain. The stress of fresh concrete
paste; and (2) the hydrophobic nature of plastic, which specimen was higher and the concrete specimen
can inhibit cement hydration reaction by restricting containing 10% plastic aggregate provided higher
water movement. The tensile strength test results of the stress from other specimens containing various amount

387
 Use of waste plastic aggregation in concrete

of plastic aggregate. The fresh concrete specimen

specime was
more brittle than others. The plastic aggregate
produced softening behavior in other specimens
resulting lower stress.

Figure 10. Stress-strain

strain behavior of concrete specimens
after 28 days.

Modulus of Elasticity

The modulus of elasticity values of fresh concrete

Figure 8. Stress-strain behavior of concrete specimens
specimen and other specimens containing 5%, 10% and
after 7 days.
20% plastic aggregate were determined at 7, 21 and 28
From Figure 9, it is observed that the stress is days of curing. Table 2 represents different modulus of
decreasing as the increasing of strain. The stress of elasticity found for different percentage of plastic
concrete specimen containing 10%plastic aggregate aggregate in the concretete specimens
specimens. The modulus of
provided higher stress than fresh concrete and from elasticity was found higher for the specimen containing
other specimens containing various amount of plastic 10% plastic aggregate by volume. The value is about
aggregate. eight times higher than that of the specimen with 0%
plastic aggregate. The modulus value decreases
drastically by 20% replacement with plastic aggregate.
It is identified that the deformation produced in the
concrete is partially related to the elastic deformation
of the aggregate. Ferreira et al. (2012) also observed
that the modulus of elasticity decreases when addition
of plastic waste aggregate increases.

Table 2. Modulus of elasticity of various concrete

specimens.

Modulus of Elasticity
Figure 9. Stress-strain
strain behavior of concrete specimens (Mpa)
Specimen
after 21 days. 21
7 days 28 days
days
From Figure 10, it was seen that the stress was C0PA 2405 5833 14500
decreasing as the increasing of strain. The stress of C5PA 2480 6000 15000
concrete specimen containing 10%plastic aggregate
C10PA 6500 8571 40000
provided higher stress than fresh concrete and from
other specimens containing various amount of plastic C20PA 340 5000 8333
aggregate.

388
 Hossain et al.
a (2016), Progressive Agriculture 27 (3): 383-391

Flexural strength plastic aggregate than that of conventional concrete.

However, the range of shrinkage for concrete
The influence of PET aggregate on the flexural
containing PET aggregate was acceptable for various
strength of concrete specimens at 7, 21 and 28 days
uses of structural concrete.
were analyzed and presented in Figure 11. It was
observed that the flexural strength was decreased as the Table 3. Shrinkage values of the concrete specimens
amount of PET aggregate increased in concrete. The
explanation for the loss of compressive and tensile Percentage of length change (%)
Specimen
strengths of concrete due to the incorporation of PET-
PET 7 days 28 days
aggregate applied to the flexural behaviour of concrete C0PA 0.20 0.40
too. Saikia and de Brito (2014) also found lower C5PA 0.25 0.44
flexural strength values forr concrete containing PET C10PA 0.28 0.45
aggregate than for concrete containing natural C20PA 0.30 0.60
aggregate only.
Conclusion
In this research, some selected physical and mechanical
properties have been investigated for various types of
concrete containing 5%, 10% and 20% of waste PET
aggregate by volume of concrete mixes
mixes. The following
conclusions can be drawn based on the laboratory test
results.

1. The specific gravity of plastic aggregate was less

than that of coarse aggregate and the apparent
specific gravity of plastic aggregate was in the
range of lightweight concrete aggregate category.
Figure 11. Influence of PET aggregate on the flexural
So, it can be used as substitute aggregate of coarse
strength of concrete.
aggregate
ate according to mix design of concrete.
Shrinkage 2. The density of concrete containing different
percentages of plastic aggregate was lower than
Table 3 shows the shrinkage values of the concrete
the fresh concrete.
specimens. It was clear that the length change of
3. The compressive strength of concrete containing
concrete increased more as the more addition of plastic
different proportion of PET was different but the
aggregate. The change was higher at 20% volume of
compressive
pressive strength at 10% volume of PET
plastic aggregate than 0% volume of plastic specimen.
provided higher strength which allowed it to be
Frigione (2010) measured the drying shrinkage
used in structural application. The tensile strength,
property off one year cured concrete containing PET
flexural strength and shrinkage values of concrete
aggregate, which replaced 5% in weight of fine natural
containing different proportion of PET indicated
aggregate. He found an increase in drying shrinkage
lower performances ces of concrete than the fresh
value due to the incorporation of PET aggregate in
concrete.
concrete for the different experimental conditions.
4. The modulus of elasticity of concrete containing
According
ding to the author, this behavior is primarily due
10% volume of PET indicated higher performance
to the lower elastic modulus of concrete containing
than fresh concrete.

389
 Use of waste plastic aggregation in concrete

5. The concrete containing 10% PET aggregate can of concrete containing recycled plastic aggregate.
be effectively used in producing lightweight Construction and Building Materials, 36, 196–204.
concrete. Frigione M, (2010). Recycling of PET bottles as fine
However, further study is required to understand aggregate in concrete. Waste Management,30,
the durability aspects of the concrete containing 1101–6.
PET aggregate. Islam MS (2011). Prospects and challenges of plastic
industries in Bangladesh. Journal of Chemical
References Engineering, 26(1), 16-21.
IS 1199-1959(10). Determination of changes in length
Al-Salem S, Lettieri P, Baeyens J (2009). Recycling
on drying and wetting (initial drying shrinkage,
and recovery routes of plastic solid waste (PSW): a
drying shrinkage, moisture movement).
review. Waste Management, 29(10), 2625-43.
Koide H, Tomon M, Sasaki T (2002).Investigation of
ASTM C127, C128 (2004). Specific gravity and
the use of waste plastic as an aggregate for
absorption tests of coarse and fine aggregates.
lightweight concrete. Sustainable Concrete
Annual Book of ASTM Standards.
Construction, London,177–186.
ASTM C39 (2004). Compressive strength of
Marzouk OY, Dheilly RM, Queneudec M (2007).
cylindrical concrete specimens. Annual Book of
Valorization of post-consumer waste plastic in
ASTM Standards.
cementitious concrete composites. Waste
ACI Committee (1987). Guide for structural
Management, 27, 310–318.
lightweight aggregate concrete. Manual of
Neville AM (1981). Properties of Concrete. Pitman
Concrete Practice.
Publishing Ltd., London.
ASTM C496 (2004). Standard test method for splitting
Rossignolo JA, Agnesini MVC (2002). Mechanical
tensile strength of cylindrical concrete specimens.
properties of polymermodified lightweight
Annual Book of ASTM Standards.
aggregate concrete. Cement Concrete Research,32,
ASTM C469 (2004). Standard test method for static
329– 334.
modulus of elasticity and Poisson’s ratio of
Rebeiz K, Fowler DW (1996). Precast use of polymer
concrete in compression. Annual Book of ASTM
concrete using unsaturatedpolyester resin base on
Standards.
recycled. Construction and Building Materials; 10,
ASTM C78 (2004). Standard test method for flexural
215–330.
strength of concrete. Annual Book of ASTM
Rebeiz KS, Fowler DW, Paul DR (1991). Recycling
Standards.
plastics in polymer concretesystems for
Albano C, Camacho N, Hernandez M, Matheus A,
engineering applications. Polymer Plastic
Gutierrez A (2009). Influence of content and
Technology Engineering, 30, 809–825.
particle size of waste pet bottles on concrete
Saikia N, de Brito J (2014). Mechanical properties and
behavior at different w/c ratios. Waste
abrasion behaviour of concrete containingshredded
Management, 29, 2707–2716.
PET bottle waste as a partial substitution of natural
Choi YW, Moon DJ, Chung JS, Cho SK (2005).
aggregate. Construction and Building Materials,
Effects of waste PET bottles aggregate on the
52, 236–244.
properties of concrete. Cement Concrete Research,
Sakr K, El-Hakim E (2005).Effect of high temperature
35, 776–781.
or fire on heavy weight concrete properties.
Ferreira L, de Brito J, Saikia N (2012). Influence of
Cement Concrete Research; 35, 590–596.
curing conditions on the mechanical performance

390
 Hossain et al. (2016), Progressive Agriculture 27 (3): 383-391

Silva DA, Betioli AM, Gleize PJP, Roman HR, Gomez Van Krevelen DW (1990). Properties of Polymers,
LA, Ribeiro JLD (2005). Degradation of recycled Elsevier, Amsterdam, The Netherlands, 1990.
PET fibers in Portland cement-based materials.
Cement and Concrete Research, 35, 1741–1746.

391