S3 Course Handout

RAJAGIRI SCHOOL OF ENGINEERING &
TECHNOLOGY
DEPARTMENT OF CIVIL ENGINEERING
COURSE
HANDOUT
S3 CE
B TECH IN CIVIL ENGINEERING

Course Handout, S3CE
RAJAGIRI SCHOOL OF ENGINEERING AND TECHNOLOGY

DEPARTMENT OF CIVIL ENGINEERING
VISION
The department strives to excel in the areas of academia, research and industry by
moulding professionals in the field of Civil Engineering to build a sustainable world.
MISSION
To impart quality education and mould technically sound, ethically responsible

professionals in the field of Civil Engineering with a broad skill set of creativity, critical
thinking and effective communication skills to meet the desired needs of the society
within realistic socio-economic environmental constraints.
Program Educational Objectives (PEOs)
Within a few years of graduation, the candidate is expected to have achieved the following
objectives:
PEO 1: Knowledge in Civil Engineering: Graduates shall attain state of the art knowledge
in the various fields of Civil Engineering and will take every opportunity coming their way
to augment the already existing knowledge.
PEO 2: Successful in career: Graduates shall achieve successful career which they will be
able to commit to with responsibility and passion.
PEO 3: Commitment to society: Graduates shall display a high sense of social

responsibility and ethical thinking and suggest sustainable engineering solutions
Program Specific Outcomes (PSOs)
Civil Engineering Graduates will be able to:
PSO 1: Structural Analysis & Design Skills: Acquire ability to analyse, design and develop
feasible solutions with emphasis to earthquake resistant design.
PSO 2: Professional Skills: Acquire ability to confront real time problems by developing
sustainable solutions.
PSO 3: Interdisciplinary Skills: Graduates will be able to collaborate with engineers from
other disciplines to develop products for the betterment of the society.
Program Outcomes (POs)
Engineering Graduates will be able to:
Department of Civil Engineering, RSET 1

PO 1. Engineering knowledge: Apply the knowledge of mathematics, science, engineering

fundamentals, and an engineering specialization to the solution of complex engineering
problems.
PO 2. Problem analysis: Identify, formulate, review research literature, and analyse

complex engineering problems reaching substantiated conclusions using first principles
of mathematics, natural sciences, and engineering sciences.
PO 3. Design/development of solutions: Design solutions for complex engineering

problems and design system components or processes that meet the specified needs with
appropriate consideration for the public health and safety, and the cultural, societal, and
environmental considerations.
PO 4. Conduct investigations of complex problems: Use research-based knowledge and

research methods including design of experiments, analysis and interpretation of data,
and synthesis of the information to provide valid conclusions.
PO 5. Modern tool usage: Create, select, and apply appropriate techniques, resources, and
modern engineering and IT tools including prediction and modelling to complex
engineering activities with an understanding of the limitations.
PO 6. The engineer and society: Apply reasoning informed by the contextual knowledge
to assess societal, health, safety, legal and cultural issues and the consequent
responsibilities relevant to the professional engineering practice.
PO 7. Environment and sustainability: Understand the impact of the professional

engineering solutions in societal and environmental contexts, and demonstrate the
knowledge of, and need for sustainable development.
PO 8. Ethics: Apply ethical principles and commit to professional ethics and

responsibilities and norms of the engineering practice.
PO 9. Individual and team work: Function effectively as an individual, and as a member

or leader in diverse teams, and in multidisciplinary settings.
PO 10. Communication: Communicate effectively on complex engineering activities with

the engineering community and with society at large, such as, being able to comprehend
and write effective reports and design documentation, make effective presentations, and
give and receive clear instructions.
PO 11. Project management and finance: Demonstrate knowledge and understanding of

the engineering and management principles and apply these to one’s own work, as a
member and leader in a team, to manage projects and in multidisciplinary environments.
PO 12. Life-long learning: Recognize the need for, and have the preparation and ability to
engage in independent and life-long learning in the broadest context of technological
change.

INDEX
SL NO: CONTENTS PAGE
1 ASSIGNMENT SCHEDULE 4
2 SCHEME: B.TECH 3RD SEMESTER 5
3 MA201: LINEAR ALGEBRA & COMPLEX ANALYSIS A.1
4 CE201: MECHANICS OF SOLIDS B.1
5 CE203: FLUID MECHANICS – I C.1
6 CE205: ENGINEERING GEOLOGY D.1
7 CE207: SURVEYING E.1
8 HS210: LIFE SKILLS F.1
9 CE231: CIVIL ENGINEERING DRAFTING LAB S.1
10 CE233: SURVEYING LAB T.1

ASSIGNMENT SCHEDULE
DATE SUB. CODE SUBJECT
3.9.2018 CE201 Mechanics of Solids

4.9.2018 CE203 Fluid Mechanics – I
5.9.2018 CE205 Engineering Geology
6.9.2018 CE207 Surveying
7.9.2018 HS210 Life Skills
2.11.2018 MA201 Linear Algebra & Complex Analysis
5.11.2018 CE201 Mechanics of Solids
7.11.2018 CE203 Fluid Mechanics – I
9.11.2018 CE205 Engineering Geology
12.11.2018 CE207 Surveying
14.11.2018 HS210 Life Skills

SCHEME: B.TECH 3RD SEMESTER
COURSE EXAM
COURSE NAME L-T-P CREDITS
CODE SLOT
MA201 Linear Algebra & Complex Analysis 3-1-0 4 A

CE201 Mechanics of Solids 3-1-0 4 B
CE203 Fluid Mechanics – I 3-1-0 4 C
CE205 Engineering Geology 3-0-1 4 D
CE207 Surveying 3-0-0 3 E
HS210 Life Skills 2-0-2 3 F
CE231 Civil Engineering Drafting Lab 0-0-3 1 S
CE233 Surveying Lab 0-0-3 1 T
Total Credits = 24 Hours: 29 Cumulative Credits= 71

A
MA 201
LINEAR ALGEBRA & COMPLEX
ANALYSIS
COURSE INFORMATION SHEET
PROGRAMME: CE DEGREE: BTECH

COURSE: LINEAR ALGEBRA & COMPLEX SEMESTER: S3
ANALYSIS L-T-P-CREDITS: 3-1-0-4
COURSE CODE: MA201
COURSE TYPE: CORE
REGULATION: 2016
COURSE AREA/DOMAIN: BASIC CONTACT HOURS: 3+1 (Tutorial)
SCIENCES hours/Week
CORRESPONDING LAB COURSE CODE
LAB COURSE NAME: NIL
(IF ANY): NIL
SYLLABUS:
UNIT DETAILS HOURS
Complex Differentiation
Limit, continuity and derivative of complex functions
I Analytic functions, Cauchy – Riemann equation, Laplaces equation, 9
Harmonic functions
Harmonic conjugate
Conformal Mapping
Geometry of Analytic functions, conformal mapping, Mapping w=z^2,
conformality of w=e^z
II The mapping w=z+1/z Properties of w=1/z 10
Circles and straight lines, extended complex plane, fixed points
Special linear fractional transformation, cross ratio, cross ratio
property – maping of disks and half planes
Conformal mapping by w=sinz, w=cosz
Complex Integration
Definition of Complex Line integrals, first evaluation method, second
evaluation method, cauchys integral theorem, Independencce of path,
III cauchys integral theorem for multy connected domains, cauchys 10
integral formula – Derivatives of analytic finctions, application of
Derivatives of analytic finctions, Taylor and Maclaurin series
Power series as Taylor series, laurents series
Residue theorem
IV Singlarities, Zeros, Poles, Essential singularity, Zeros of an analytic 9
functions, Residue integration method, formulas, several singularities
inside the contour residue theorem, Evalution of real integral
Linear system of equations
Linear system of equations, Coefficient matrix, Augmented matrix,
Gauss Elimination and back substitution, Elementary row operations,
V Row equivalent systems, Gauss elimination –three possible cases, 9
Row echelon form and information from it, Linear independence –
rank of a matrix, vector Space Dimension – basis, Vector space
R^3,Solution of linear systems, Fundamental theorem of non-
homogeneous linear systems, homogeneous linear systems
Department of Civil Engineering, RSET A.2

UNIT DETAILS HOURS

Matrix Eigen value Problem
Determination of Eigen values and Eigen vectors, Eigen space,
VI Symmetric, skew symmetric and Orthogonal matrices – Simple 9
properties, Basis of Eigen vectors, Similar matrices, Diagonalisation
of a matrix, Principal axis theorem Quadratic forms
TOTAL HOURS 52
TEXT/REFERENCE BOOKS:
T/R BOOK TITLE/AUTHORS/PUBLICATION
T1 Erin Kreyszig:Advanced Engineering Mathematics,10th edition.wiley
R1 Dennis g Zill&Patric D ShanahanA first course in complex analysis with
applications-Jones &Bartlet publishers
R2 B.S Grewal-Higher Engineering mathematics,Khanna publishers,New Delhi
R3 Lipschutz,Linear Algebra,3e(Schaums Series)McGraww Hill Education
India2005
R4 Complex variables introduction and applications-second edition-Mark.J.Owitz-
Cambridge publication
COURSE PRE-REQUISITES:
C.CODE COURSE NAME DESCRIPTION SEMESTER
Higher secondary To develop basic ideas on matrix
level mathematics operations, calculus, complex numbers
etc
COURSE OBJECTIVES:
1 To equip the students with methods of solving a general system of linear
equations
2 To familarize them with the concept of Eigen value and Diagonalisation of a
matrix which have many application in engineering
3 To understand the basic theory of functionsof a complex variable and conformal
transformations
COURSE OUTCOMES:
Sl
PO1 PO2 PO3 PO4 PO5 PO6 PO7 PO8 PO9 PO10 PO11 PO12
No.
The students will be able to understand about complex numbers and functions
1
H
The students will be able to get an idea of Conformal mapping
2
H
The students will be able to understand the integration of complex functions
3
H L H

Sl
No.
The students will be able to gain knowledge of various singularities and series
4 expansions
H H
The students will be able to find the rank of a matrix and solution of equations
5 using matrix theory
H H
The students will be able to understand the matrix Eigen value problems
6
H L H
JUSTIFICATION FOR CO-PO MAPPING:

CO PO MAPPING JUSTIFICATION
Fundamental knowledge in complex analysis will help to
CO1 PO1 HIGH
analyse the Engineering problems very easily
Basic knowledge in Conformal mapping will help to model
CO2 PO1 HIGH
various problems in engineering fields
Complex integration will help to simplify problems with high
PO1 HIGH
complexity in Engineering
CO3 PO2 LOW
Complex integration will help to design solutions to various
PO3 HIGH
complex engineering problems
Singularities and Series expansions will help to enrich the
PO1 HIGH
analysis of Engineering problem
CO4
Singularities and Series expansions will help to design
PO3 HIGH
solutions to various complex engineering problems
Matrix theory will give a thorough knowledge in the
PO1 HIGH
application problem
CO5
Will able to analyse various methods of solutions of
PO2 HIGH
equations
Eigen value, Eigen vectors and related theories will help to
PO1 HIGH
design several engineering problem
CO6 PO2 LOW
The solutions for various engineering problems requires
PO3 HIGH
Matrix theory
GAPS IN THE SYLLABUS - TO MEET INDUSTRY/PROFESSION REQUIREMENTS:

Sl No DESCRIPTION PROPOSED ACTIONS
1 Basic concepts on complex analsis Reading, Assignments
2 Application of complex analysis in solving various Reading
Engineering problems

3 Importance of matrix application in different Reading

fields of our society
TOPICS BEYOND SYLLABUS/ADVANCED TOPICS/DESIGN:

Sl No DESCRIPTION
1 Application of analytic functions in Engineering
2 Application of Complex integration in Engineering
3 Advanced matrix operations
4 Some applications of eigen values
WEB SOURCE REFERENCES:

Sl No DESCRIPTION
1 http://www.math.com/
DELIVERY/INSTRUCTIONAL METHODOLOGIES:
CHALK & TALK STUD. ASSIGNMENT WEB RESOURCES
LCD/SMART
STUD. SEMINARS ADD-ON COURSES
BOARDS
ASSESSMENT METHODOLOGIES-DIRECT
STUD. TESTS/MODEL UNIV.
ASSIGNMENTS
SEMINARS EXAMS EXAMINATION
STUD. LAB STUD. MINI/MAJOR
CERTIFICATIONS
PRACTICES VIVA PROJECTS
ADD-ON
OTHERS
COURSES
ASSESSMENT METHODOLOGIES-INDIRECT
ASSESSMENT OF COURSE STUDENT FEEDBACK ON
OUTCOMES (BY FEEDBACK, ONCE) FACULTY (TWICE)
ASSESSMENT OF MINI/MAJOR
OTHERS
PROJECTS BY EXT. EXPERTS
Prepared by Approved by
Fr. Ajeesh Puthussery Dr. Antony V. Varghese

COURSE PLAN
HOUR MODULE TOPICS PLANNED

HOUR 1 Complex functions, limit, continuity of complex functions
HOUR 2 Derivative and analytic functions
HOUR 3 Cauchy Reimann equations
HOUR 4 I Laplace’s equation, harmonic functions
HOUR 5 Sensitivity analysis
HOUR 6 Harmonic conjugate
HOUR 7 Problem Solving
HOUR 8 Mapping w=z^2
HOUR 9 Geometry of analytic functions
HOUR 10 Conformality of w=e^z
HOUR 11 The mapping w=z+1/z
HOUR 12 Properties of 1/z
HOUR 13 II Circles and straight lines
HOUR 14 Fixed points, special linear fractional transformations
HOUR 15 Extended complex plane
HOUR 16 Cross ratio and property
HOUR 17 Mapping of disks and half-planes
HOUR 18 Conformal mapping by w = sin z or w = cos z
HOUR 19 Complex line integrals, first evaluation method
HOUR 20 Second evaluation method, Cauchy's integral theorem
HOUR 21 Independence of path
HOUR 22 Cauchy’s integral theorem for multiply connected domains
HOUR 23 III Cauchy's integral formula
HOUR 24 Derivatives of analytic functions and applications
HOUR 25 Taylor's series, Maclaurin's series
HOUR 26 Power series as Taylor series
HOUR 27 Laurent's series
HOUR 28 Singularities, zeroes, poles
HOUR 29 Essential singularity
HOUR 30 Zeroes of analytic functions
HOUR 31 Residue integration method
IV
HOUR 32 Formulas for residues, several singularities inside the contour
HOUR 33 Residue theorem
HOUR 34 Evaluation of real integrals – Type I
HOUR 35 Evaluation of real integrals – Type II
HOUR 36 Linear system of equations
HOUR 37 Coefficient matrix, augmented matrix
HOUR 38 Gauss elimination method
HOUR 39 Elementary row operations
HOUR 40 V Row equivalent systems
HOUR 41 Gauss elimination
HOUR 42 Rank of a matrix in vector space
HOUR 43 Dimension, basis, vector space
HOUR 44 Solution of linear systems

HOUR 45 Homogeneous linear systems

HOUR 46 Problems
Eigen space, symmetric and skew-symmetric and orthogonal
HOUR 47
matrices
HOUR 48 Basis of eigen vectors, similar matrices
HOUR 49 VI Diagonalization of a matrix
HOUR 50 Quadratic forms
HOUR 51 Principal axis theorem
HOUR 52 Problems

ASSIGNMENT – I
1. State True or False and Justify

a. If f(z) is analytic, then f'(z) exists.
b. Function f(z) may be differentiable at z = z0, but not analytic near z = z0.
c. Function v(x, y) = -3xy2 + x3 is an harmonic function.
d. The harmonic conjugate of u(x, y) = -2xy is
e. If f(z0) exists, then function f must be continuous at z = z0.
f. If lim z zo f(z) exists, then function f must be continuous at z = z0.
g. The function f(z) = sin(1/z) is continuous everywhere.
h. The function f(z) = cos(z3) is continuous everywhere.
i. If function f is continuous at z = z0, then f must be differentiable there.
j. If f(z) = | z |2, then for all z, f '(z) = 2z.
k. If f(z) = (iz + 2)2, then f '(z) = 4i - 2z.
l. If f(z) = cos(z3), then f '(z) = - sin(z3).
m. If f(z) = u + iv and the Cauchy-Riemann equations hold for u, v, then f '(z)
must exist.
n. For f = u + iv, the Cauchy-Riemann equations are ux = vy and vx = uy.
o. If f(z) = (x2 - y2 + 2) + 2ixy = u + iv, then the Cauchy-Riemann equations
hold.
p. If f(z) is differentiable, then f '(z) = vy - i uy.
q. A smooth continuous arc is a contour.
r. If C is a contour, then C must be a smooth continuous arc.
x
u 2
2. Define harmonic function. Verify that x  y 2 is a harmonic. Also find the
conjugate harmonic function of u.
3.
a. Show that is a harmonic conjugate
of
b. Show that is a harmonic function and find the
harmonic conjugate .
c. Determine where the following functions are harmonic.
and .
d. Find the value of a if u(x, y) = ax2 – y2 + xy is harmonic.
e. Let a, b and c be real constants. Determine a relation among the coefficients
that will guarantee that the function is
harmonic.
4. Let for . Compute the partial derivatives

of and verify that satisfies Laplace's equation.
5. Find an analytic function for the following expressions.

a.
b.
c.
d. .
e.
f. .
6. Show that are harmonic functions but that their
product is not a harmonic function.
7. Let be a harmonic conjugate of . Show that is the
harmonic conjugate of .
8. Let be a harmonic conjugate of . Show
that is a harmonic function.
9. Suppose that is a harmonic conjugate of and that is
the harmonic conjugate of .
10. Consider the function u( x, y)  e sin( y) . Is it harmonic ? If so, find its harmonic
x
conjugate. Do the same for

a. u( x, y)  x  2 xy  xy
3 3
b. u( x, y)  e cos(x)
y
2
11. Show that the transformation w z transforms the families of lines x  h and y k
into confocal parabolas, having w  0 as the common focus.
12. Find the bilinear transformation which maps 1, 0,1 of the z-plane anto 1, i,1 of
the w-plane. Show that under this transformation the upper half of the z-plane
w 1
maps anto the interior of the unit circle .
1
w
13. Show that by means of the inversion z the circle given by z 3  5 is mapped
3 5
w 
into the circle 16 16 .
1/ 2
14. Show that the transformation w z maps the upper half of the inside of the
parabola y  4c c  x  into the infinite strip bounded by 0  u  , 0  v  c where
2 2 2
w  u iv .
15. Find the image of the hyperbola x2 – y2 = 10 under the transformation w = z2
6z  9
w
16. Find the fixed points of the transformation z
1
w
17. Find the invariant point of the transformation z  2i
18. Find the bilinear transformation that maps z = (1, i, –1) into w=(2, i, –2).
19. Find the image of the circle |z| = 2 by the transformation w = z + 3 +2i

20. Solve the following linear system given explicitly or by its augmented matrix by
Gauss elimination method:
a.
b.
c.
21. Find the rank and basis for the row space and a basis for the column space.
a.
b.
22. Are the following set of vectors linearly independent:
a. ,
b. , ,
23. Is the given set of vectors a vector space? Give reason. If yes determine the
dimension and find a basis.
a. All vectors in with
b. All vectors in with

24. Find the rank of the matrix
25. Solve the linear system by its augmented matrix
26. Is the given set of vectors a vector space give a reason. If yes determine the
dimension and find the basis.( denote components)
a. All vectors in such that 4 + =k
b. All vectors in such that 3 -2 + = 0, 4 + =0

c. All real numbers.
27. Solve by Gauss elimination method
a. 2w+3x +y-11z = 1
b. 5w -2x +5y -4z =5

c. w –x+3y -3z =3
d. 3w+ 4x -7y +2z = -7
28. Solve the following
a. 4y+3z=8
b. 2x-z=2
c. 3x+2y=5
29. Which of the following matrices have linearly dependent rows?
1 0 0 1 2 3 2 3 8 
0 1 0  4 5 6 15 5 9 
     
0 0 1 7 8 9  6 9 24
A= B= C=
30. Find the eigen values and eigenvectors of the matrix
5 4 2
A   4 5 2
 2 2 2
0 1 2
A   2 3 0 
0 4 5 

TUTORIALS
1. Prove that 𝑢 = 2𝑥 − 𝑥 3 + 3𝑥𝑦 2 is harmonic and find its harmonic conjugate. Also
find the corresponding analytic function.
2.
a. Show that 𝑒 𝑥 (𝑥 cos 𝑦 − 𝑦 sin 𝑦) is harmonic function. Find the analytic
function f(z) for which 𝑒 𝑥 (𝑥 cos 𝑦 − 𝑦 sin 𝑦) is the imaginary part.
b. Find f(z) whose imaginary part is 𝑣 = 𝑥 2 − 𝑦 2 + 2𝑥𝑦 − 3𝑥 − 2𝑦
3.
a. If 𝑢 + 𝑣 = (𝑥 − 𝑦)(𝑥 2 + 4𝑥𝑦 + 𝑦 2 ) and 𝑓(𝑧) = 𝑢 + 𝑖𝑣, find f(z) in terms of
z
b. If 𝑢 − 𝑣 = 𝑒 𝑥 (cos 𝑦 − sin 𝑦), find f(z) in terms of z
4. Show that the function defined by
0 𝑤ℎ𝑒𝑛 𝑧 = 0
2
𝑓(𝑧) = {(𝑧̅) 𝑥 − 3𝑥𝑦 2
3
𝑦 3 − 3𝑥 2 𝑦
= 2 + 𝑖 𝑤ℎ𝑒𝑛 𝑧 ≠ 0
𝑧 𝑥 + 𝑦2 𝑥2 + 𝑦2
is not differentiable at the point z0 = 0 even though the Cauchy-Riemann
equations (3-16) are satisfied at the point (0,0).
5. Show that the function 𝑓(𝑧) = 𝑧̅ is nowhere differentiable.

QUESTION BANK
1. Prove that the function

𝑥 2 𝑦 5 (𝑥 + 𝑖𝑦) 𝑖𝑓 𝑧 ≠ 0
𝑓(𝑧) = {
0 𝑖𝑓 𝑧 = 0
satisfies C-R equations at z = 0, but it is not analytic at z = 0.
2.
a. If f(z) is analytic and uniformly bounded in every domain then
i. f(z) is zero
ii. f(z) is constant
iii. f(z) is discontinuous
iv. None of these
b. If = 𝑥 3 − 3𝑥𝑦 2 , show that there exists a function v(x,y) such that w = u + iv
is analytic in a finite region.
𝑥𝑦 2 (𝑥+𝑖𝑦)
𝑖𝑓 𝑧 ≠ 0
c. c) Show that 𝑓(𝑧) = { 𝑥 2 +𝑦 2 is not differentiable at z = 0.
0 𝑖𝑓 𝑧 = 0
3.
a. Does an analytic function 𝑓(𝑧) = 𝑢(𝑥, 𝑦) + 𝑖 𝑣(𝑥, 𝑦) exist for which (𝑥, 𝑦) =
𝑥 3 + 𝑦 3 ? Why or why not?
b. Let 𝑢1 (𝑥, 𝑦) = 𝑥 2 − 𝑦 2 and 𝑢2 (𝑥, 𝑦) = 𝑥 3 − 3𝑥𝑦 2 . Find derivative of 𝑓(𝑧) =
𝑧 2 by using the definition.
4. Show that the function 𝑓(𝑧) = (𝑥 3 − 3𝑥𝑦 2 ) + 𝑖(3𝑥 2 𝑦 − 𝑦 3 ) is differentiable.
5. If 𝑓(𝑧) = |𝑧|2 show that f(z) is differentiable only at z = 0.
6. Find the image of the circle |z – 1| = 1 in the complex plane under the mapping w
1
=𝑧
7. Find the bilinear transformation which maps the points z1 = -1, z2 = 0, z3 = 1 into
the points w1 = 0, w2 = i, w3 = 3i respectively
8. Determine the bilinear transformation which maps z1 = 0 z2 = 1 z3 = ∞ into w1
= i, w2 = -1, w3 = - i respectively
9. Find the bilinear transformation which transforms (0,-i,-1) into the points (i,1,0)
10. Find the bilinear transformation which maps the points z1 = 2, z2 = i and z3 = -2
onto w1 = 1, w2 = i and w3 = -1 respectively.
5−4𝑧
11. Show that the transformation 𝑤 = maps the unit circle |z|=1 into a circle of
4𝑧−2
radius unity and centre -1/2.
12. Answer in one or two sentences:
a. The function f(z) = Rez is no where differentiable. Give reason
b. The transformation 𝑤 = 𝑧̅ is not a bilinear transformation. Why?
c. Prove that any bilinear transformation can be expressed as a product of
translation, rotation, magnification or contraction and inversion.
13. Determine the row-rank of

1 2 1
𝐴 = [2 3 1 ]
1 1 2
14. Solve the following linear system.
a. 𝑥 + 𝑦 + 𝑧 + 𝑤 = 0, 𝑥 − 𝑦 + 𝑧 + 𝑤 = 0 and −𝑥 + 𝑦 + 3𝑧 + 3𝑤 = 0
b. 𝑥 + 2𝑦 + 3𝑧 = 1 and 𝑥 + 3𝑦 + 2𝑧 = 1
15. Find the condition on a, b, c so that the linear system is consistent.
𝑥 + 2𝑦 − 3𝑧 = 𝑎, 2𝑥 + 6𝑦 − 11𝑧 = 𝑏, 𝑥 − 2𝑦 + 7𝑧 = 𝑐
16. Let A be an n × n matrix. If the system 𝐴2 𝑥 = 0 has a non trivial solution then show
that 𝐴𝑥 = 0 also has a non trivial solution.
17. Solve the system of equations given by:
a. 𝑥 + 3𝑦 + 2𝑧 = 10, 2𝑥 − 𝑦 + 3𝑧 = 8, 3𝑥 + 2𝑦 + 5𝑧 = 18
b. 𝑥 + 3𝑦 + 2𝑧 = 10, 2𝑥 − 𝑦 + 3𝑧 = 8, 3𝑥 + 2𝑦 + 5𝑧 = 19
c. 𝑥1 + 𝑥2 + 3𝑥3 + 𝑥4 − 𝑥5 = 10, 𝑥1 + 2𝑥2 + 𝑥4 = 12, 𝑥3 + 2𝑥4 + 𝑥5 = 16
d. 3𝑥 + 𝑦 − 2𝑧 = 0, 2𝑥 + 2𝑦 − 5𝑧 = 0, 5𝑥 + 3𝑦 + 2𝑧 = 0
2 3 5 8
18. 23. Row reduce [2 0 2 4]
1 3 4 0
3 1 2
19. What is the rank of [𝐴] = [2 0 5] ?
1 2 3
20. Find conditions on the constant a such that the linear system has zero, one or
infinitely many solutions
𝑥 + 𝑦 + 3𝑧 = 𝑎
𝑎𝑥 + 𝑦 + 5𝑧 = 4
𝑥 + 𝑎𝑦 + 4𝑧 = 𝑎
21. Classify these systems as either consistent or inconsistent. If the system is
consistent, further categorize it as underdetermined or uniquely determined.
Explain why the system fits into that category. Also, explain what this means
graphically for each system.
1
a. 2𝑥1 + 3𝑥2 = 9 and 3𝑥1 + 4 ⁄2 𝑥2 = 9
b. 3𝑥1 + 4𝑥2 = 7 and 9𝑥1 + 12𝑥2 = 21
c. 2𝑥1 + 3𝑥2 = 8 and 3𝑥1 + 4𝑥2 = 11
22. For what values of c and k, the following systems have no solution, a unique
solution and infinite number of solutions.
a. 𝑥 + 𝑦 + 𝑧 = 3, 𝑥 + 2𝑦 + 𝑐𝑧 = 4, 2𝑥 + 3𝑦 + 2𝑐𝑧 = 𝑘
b. 𝑥 + 𝑦 + 𝑧 = 3, 𝑥 + 𝑦 + 2𝑐𝑧 = 7, 𝑥 + 2𝑦 + 3𝑐𝑧 = 𝑘
c. 𝑥 + 𝑦 + 2𝑧 = 3, 𝑥 + 2𝑦 + 𝑐𝑧 = 5, 𝑥 + 2𝑦 + 4𝑧 = 𝑘
d. 𝑘𝑥 + 𝑦 + 𝑧 = 1, 𝑥 + 𝑘𝑦 + 𝑧 = 1, 𝑥 + 𝑦 + 𝑘𝑧 = 1
e. 𝑥 + 2𝑦 − 𝑧 = 1, 2𝑥 + 3𝑦 + 𝑘𝑧 = 3, 𝑥 + 𝑘𝑦 + 3𝑧 = 2

B
CE 201
MECHANICS OF SOLIDS

SEMESTER: S3
COURSE: MECHANICS OF SOLIDS
L-T-P-CREDITS: 3-0-1-4
COURSE CODE: CE201
COURSE TYPE: CORE
REGULATION: 2015
COURSE AREA/DOMAIN: CIVIL
CONTACT HOURS: 3+1 (Tutorial)
ENGINEERING
(IF ANY): NIL
SYLLABUS:
UNIT DETAILS HOURS
Review of Statics: Types of external loads – internal stresses –
normal and shear stresses – strain – Hooke’s law – working stress –
I 9
stress strain diagrams – Poisson’s ratio – relationship between elastic
constants
Elongation of bars of constant and varying sections – statically
indeterminate problems in tension and compression – Temperature
II 9
effects – strain energy and complementary energy – strain energy due
to tension, compression and shear.
Bending Moment & Shear force: Different types of beams – various
types of loading – Relationship connecting intensity of loading,
III shearing force and bending moment – shear force and bending 9
moment diagrams for cantilever beams and Simply supported beams
for different types of loading.
Stresses in beams of symmetrical cross sections: Theory of simple
bending – assumptions and limitations – Normal stresses in beams –
IV Stresses in non-prismatic beams – moment of resistance – beams of 9
uniform strength – beams of two materials – strain energy due to
bending – shearing stresses in beams
Analysis of stress and strain on oblique sections: Stress on
inclined planes for axial and biaxial stress fields – principal stresses –
Mohr’s circle of stress.
Thin and Thick Cylinders: Stresses in thin cylinders – thick
V cylinders – Lame’s equation – stresses in thick cylinders due to 9
internal and external pressures.
Torsion: Torsion of solid and hollow circular shafts – Pure shear –
strain energy in pure shear and torsion.
Springs: Close coiled and open coiled helical springs
Deflection of statically determinate beams: Differential equation
of the elastic curve – Method of successive integration, Macaulay’s
method, Method of superposition, moment area method.
VI 11
Theory of columns: Direct and bending stresses in short columns-
Kern of a section. Buckling and stability – Euler’s buckling/crippling
load for columns with different end conditions – Rankine’s formula
TOTAL HOURS 56
Department of Civil Engineering, RSET B.2

T1 Timoshenko, Strength of Materials Vol. I & Vol. II , CBS Publishers &
Distributers, New Delhi
T2 S.S Bhavikatti , Structural analysis Vol, Vikas Publications (P) Ltd.4th Edition
T3 James M Gere & Stephen P Timoshenko , Mechanics of Materials , CBS Publishers
&Distributers, New Delhi
T4 Egor P Popov, Mechanics of solids, Prentice Hall of India, New Delhi.
T5 Rajput R.K. Strength of Materials, S.Chand &company Ltd., New Delhi
T6 S.B Junnarkar& H.J Shah, Mechanics of Structures Vol II, Charotar publishing
House.
BE100 ENGINEERING Concepts of equilibrium forces,
S1S2
MECHANICS actions and reactions.
CE100 Knowledge of civil engineering
BASIC CIVIL
materials and structural S1S2
ENGINEERING
components of buildings
ME100 BASIC MECHANICAL Knowledge of basic theory of
S1S2
ENGINEERING machines
CY100 ENGINEERING Basic concepts of material
S1S2
CHEMISTRY properties
COURSE OBJECTIVES:
1 To enable the students to stresses and strains generated in material due to
external loads for various types of loading conditions
COURSE OUTCOMES:
Sl
No.
The students will be able to explain the concept of simple stresses and strains
1 and the various elastic constants.
M L L
The students will be able to solve for normal, shear, torsion and bending
2 stresses and strains in structural member.
H M M
The students will be able to solve the internal forces in members subject to
3 axial loads, shear, torsion and bending and plot their distributions.
H M M
The students will be able to understand the theory of simple bending and
4
analyse the stress variations in composite materials.

Sl
No.
M L L
The students will be able to analyse stress at a point and determine the
principal and maximum shear stresses using equations as well as the Mohr’s
5
circle.
H H H
The students will be able to analyse stress in cylinders due to internal and
6 external pressures.
H H M
The students will be able to discuss the concept of column buckling and critical
7 load and stress.
H H
The students will be able to analyse the deflection of statically determinate
8 beams.
H H H

Apply the knowledge of mathematics, science, engineering
PO1 MEDIUM
fundamentals to compute various elastic constants.
Identify, formulate analyse engineering problems reaching
CO1 substantiated conclusions using first principles of
PO2 LOW
mathematics, natural sciences, and engineering sciences to
compute various elastic constants.
PO4 LOW
PO1 HIGH
fundamentals to compute different types of stresses.
PO2 MEDIUM
compute different types of stresses.
PO4 MEDIUM
PO1 HIGH
fundamentals to compute the internal forces.
PO2 MEDIUM
compute the internal forces.
PO4 MEDIUM

PO1 MEDIUM
fundamentals to compute stresses in composite materials.
substantiated conclusions using first principles of
PO2 LOW
CO4
compute stresses in composite materials.
Use research-based knowledge and research methods
including design of experiments, analysis and interpretation
PO4 LOW
of data, and synthesis of the information to provide valid
conclusions for computing elastic constants.
Apply the knowledge of mathematics, science, and
PO1 HIGH
engineering fundamentals to compute the principal stresses.
PO2 HIGH
CO5
compute the principal stresses.
PO4 HIGH
of data, and synthesis of the information to provide valid
conclusions for computing different types of stresses.
PO1 HIGH
fundamentals to compute pressures of cylinders.
PO2 HIGH
CO6 compute pressures of cylinders.
PO4 MEDIUM of data, and synthesis of the information to provide valid
conclusions for computing different types of pressures in
cylinders.
PO1 HIGH fundamentals to compute column buckling and critical load
and stress.
CO7 Identify, formulate analyse engineering problems reaching
PO2 HIGH
compute column buckling and critical load and stress.
CO8 PO1 HIGH fundamentals to compute deflection of statically determinate
beams.

PO2 HIGH
compute deflection of statically determinate beams.
PO4 HIGH of data, and synthesis of the information to provide valid
conclusions for computing deflection of statically
determinate beams.

1 Basic concepts in analysing truss members; their Assignment
deformation
2 Method of estimating deflection using conjugate Assignment
beam method

Sl No DESCRIPTION
1 Mohr’s circle of stress for elements subjected to stresses in three mutually
perpendicular directions

Sl No DESCRIPTION
1 http://www.nptel.ac.in
2 http://www.rmcet.com/Resources
LCD/SMART
BOARDS
ASSIGNMENTS
CERTIFICATIONS
ADD-ON
OTHERS
COURSES

OTHERS
Anu Mathew Dr. Aysha Zeneeb Majeed

COURSE PLAN

HOUR 1 Introduction to MOS
HOUR 2 Types of external loads, internal stresses
HOUR 3 Normal and shear stresses, strain, Hooke’s law
HOUR 4 Working stress
HOUR 5 Stress strain diagrams
HOUR 6 Problems based on Hooke’s law
1
HOUR 7 Poisson’s ratio
HOUR 8 Relationship between elastic constants
HOUR 9 Problems based on elastic constants
HOUR 10 Problems based on elastic constants
HOUR 11 Problems , Elongation of bars of constant sections
HOUR 12 Elongation of bars of constant sections
HOUR 13 Statically indeterminate structures
HOUR 14 Statically indeterminate problems in tension and compression
2
HOUR 15 Temperature effects
HOUR 16 Problems on temperature effects
HOUR 17 Strain energy
HOUR 18 Complementary energy
HOUR 19 Strain energy due to tension
HOUR 20 Problems on strain energy
HOUR 21 Strain energy due to compression and shear
HOUR 22 Problems on strain energy
HOUR 23 Introduction to Bending Moment & Shear force
HOUR 24 Different types of beams
HOUR 25 Various types of loading
3
Relationship connecting intensity of loading , shearing force
HOUR 26
and bending moment
Shear force and bending moment diagrams for cantilever
HOUR 27
beams with different types of loading
Shear force and bending moment diagrams for cantilever
HOUR 28
beams with different types of loading
Shear force and bending moment diagrams for simply
HOUR 29
supported beams with different types of loading
Shear force and bending moment diagrams for simply
HOUR 30
4 supported beams with different types of loading
HOUR 31 Shear force and bending moment diagrams for beams
HOUR 32 Shear force and bending moment diagrams for beams
HOUR 33 Introduction to stresses in beams of symmetrical cross sections
HOUR 34 Introduction to stresses in beams of symmetrical cross sections

HOUR 35 Theory of simple bending

HOUR 36 Assumptions and limitations of simple bending
HOUR 37 Normal stresses in beams
HOUR 38 Stresses in non-prismatic beams
HOUR 39 Moment of resistance
HOUR 40 Problems related to moment of resistance
HOUR 41 Beams of uniform strength
HOUR 42 Beams of two materials
HOUR 43 Strain energy due to bending
HOUR 44 Stress on inclined planes for axial and biaxial stress fields
HOUR 45 Principal stresses
HOUR 46 Mohr’s circle of stress
HOUR 47 Problems
HOUR 48 Problems
HOUR 49 Stresses in thin cylinders
HOUR 50 Thick cylinders - Lame’s equation
Stresses in thick cylinders due to internal and external
HOUR 51
pressures
HOUR 52 Problems on thick and thin cylinders
Torsion of solid and hollow circular shafts.-Pure shear- strain
HOUR 53
energy in pure shear and torsion.
HOUR 54 Close coiled and open coiled helical springs
HOUR 55 Differential equation of the elastic curve
HOUR 56 Method of successive integration
HOUR 57 Macaulay’s method
HOUR 58 Method of superposition
HOUR 59 Moment area method
HOUR 60 Problems on moment area method
HOUR 61 Direct and bending stresses in short columns
6
HOUR 62 Problems
HOUR 63 Kern of a section
HOUR 64 Buckling and stability
Euler’s buckling/crippling load for columns with different end
HOUR 65
conditions
Euler’s buckling/crippling load for columns with different end
HOUR 66
conditions
HOUR 67 Problems
HOUR 68 Rankine’s formula
HOUR 69 Revision

ASSIGNMENT – I
1. In an experiment, a bar of 40 mm diameter is subjected to a pull of 60 kN. The

measured extension on a gauge length of 200 mm is 0.09 mm and the change in
diameter is 0.0041 mm. The Poisson's ratio and the value of the three moduli.
2. A railway line is laid so that there is no stress in the rails at 10oC. Find
a. The stress on the rails at 50oC if there is no allowance for expansion.
b. The stress in the rails if there is an expansion allowance of 8 mm.
c. The expansion allowance if the stress in the rails is to be zero.
d. The maximum temperature to have no stress in the rails if the expansion
allowance is 14 mm.
The rails are 30 mm long. Take α= 12x10-6 per OC and E=2x 105N/mm2.
3. A cylindrical bar with two sections of lengths 50 cm and 25 cm, and diameter 20
mm and 15 mm respectively, is subjected to an axial pull such that the maximum
stress is 150MN/m2. Find the strain energy stored in bar. E= 200 GN/m2.
4. A bar of 550 mm length is attached rigidly at A and B as shown in Figure. Forces
of 30 kN and 60 kN acts at point C and D. If E = 200 kN/mm2. Determine the
reactions at two ends. If the bar diameter is 25 mm Calculate the stresses and the
change in length of each portion. (Hint: bar is rigidly fixed at the ends. Hence net
deformation is zero)
A B C D
30 kN 50 kN
200mm 150 mm 200 mm
5. A bar of length 1000mm and diameter 30mm is bored for 400mm, the bore
diameter being 10mm as shown in fig. Under a load of 30kN if the extension of bar
is 0.222mm what is modulus of elasticity?

ASSIGNMENT – II
R is your roll number

1. Plot shear force and bending moment diagrams of the cantilever beam
2. Plot the shear force and bending moment diagram of the cantilever
3. Plot the shear force and bending moment diagrams of the overhang beam. Also
locate the points of contraflexure if any.
4. Plot the shear force and bending moment diagrams of the simple beam.
5. (a) Explain the basic concepts in analysing truss members and their deformation
(b) Discuss the steps involved in estimating deflection using conjugate beam
method
(c) Analyse Mohr’s circle of stress for elements subjected to stresses in three
mutually perpendicular directions

TUTORIAL QUESTIONS
1. A concrete cylinder of diameter 150mm and length 300mm when subjected to an

axial load, compression of 240kN resulted in an increase of diameter by 0.127 mm
and decrease in length by 0.28mm. Compute the Poisson’s ratio and Modulus of
Elasticity.
2. For a given material E=110 GPa and G=42 GPa. Determine the Bulk Modulus and
lateral contraction of a round bar of 37.5mm dia and 2.4m long when stretched by
2.5mm.
3. The following data relate to a bar subject to tensile test. Diameter of bar is 30mm,
tensile load is 54kN, Gauge length is 300mm, the extension of bar is 0.112mm,
change in diameter is 0.00366mm. Determine Poisson’s ratio, E, G, K.
4. A CI flat, 300mm long and of 30mm× 50mm uniform section is acted upon by the
following forces uniformly distributed over the respective cross section; 25kN in
the direction of length (T), 350kN in the direction of width (C) and 200kN in the
direction of thickness (T). Determine the change in volume of flat, E=140GPa and
Poisson’s ratio=0.25.
5. A steel bar 60×60 mm in section and 180mm long is subjected to a tensile load of
300kN along its length and tensile load of 750kN and 600KN on lateral faces.
Calculate change in dimension of bar and change in volume. E=200GPa and
Poisson’s ratio=0.3
6. A member ABCD is subjected to a point load P1, P2, P3 and P4 as shown in figure.
Find the force P2 necessary for equilibrium if P1=45kN, P3=450kN and P4=130kN.
Determine the total elongation of the member. Take E=210 kN/mm2.
7. A mild steel bar 20mm in dia and 300mm long is enclosed in a brass tube whose
external diameter is 30mm and internal diameter is 25mm. The composite bar is
the subjected to an external pull of 40kN. If E=200GPa and that for brass is 100GPa
Calculate the stress in bar and tube, the extension of the bar and the work done in
stretching.
8. A reinforced concrete column of 230mm×450mm size with 6nos 16mm dia steel
bar as shown in fig. is subjected to an axial load of 500kN. Compute the stress
developed in each material. Consider Es=200 GPa and Ec=15GPa.

9. A gun metal rod 22mm dia screwed at the ends passes through a steel tube 25mm
internal diameter and external diameter 30mm. The temperature of whole
assembly is raised to 126°C and the nuts on the rod are tightly screwed to the ends
of the tube when the common temperature has fallen to 16°C.αs=12×10-6/°C,
.αg=20×10-6/°C, Es=210GPa, Eg= 94 GPa.
10. Both portions of the rod ABC are made of Aluminium for which E=73GPa. Knowing
that the diameter of the portion AB is 30mm and BC is 20mm, determine the
largest force P that can be applied if the allowable stress is 160Mpa and the
deflection at point C not exceed 4mm.
1.2m 0.8m
11. A small block is 4cm long and 3cm high and 0.5cm thick. It is subjected to a
uniformly distributed tensile force of resultant 1200N and 500N as shown in
figure. Find stress developed along AB.
12. At a point within a body subjected to two mutually perpendicular directions the
stresses are 80MPa (T) and 40MPa (T). Determine the normal shear and resultant
stresses on an oblique plane inclined at an angle of 45˚ with minor axis.
13. Diameter of a water supply pipe is 750mm. It has to withstand a waterhead of
60m. Calculate the thickness of the thin pipe if the permissible stress is 20N/mm2.
14. A steel cylinder 240mm internal diameter is to withstand an internal pressure of
5N/mm2.The increase in area of the bore due to resulting radial expansion is

limited to 0.1% of nominal area. Calculate the necessary thickness of the cylinder
and the circumferential stress induced in the section taking E=2.1×105N/mm2.
15. Power of 2250 KW has to be transmitted@1Hz. If the permissible shear stress is
80N/mm2 determine the necessary diameter for a solid shaft of circular section. If
a circular section is used with an internal diameter of 0.75 times the external
diameter the saving in mass per metre length of the shaft.
16. An overhanging beam ABC is supported at A and B is loaded as shown in Fig.
Determine the deflection at the free end C and max deflection between A and B.
E=200GPa and I=13.5×10-6m3

C
CE 203
FLUID MECHANICS - I
Course Handout, S3 CE

SEMESTER: S3
COURSE: FLUID MECHANICS I
COURSE CODE: CE203
COURSE TYPE: CORE
REGULATION: 2016
CONTACT HOURS: 4 hours/Week.
ENGINEERING
CORRESPONDING LAB COURSE CODE LAB COURSE NAME:FLUID MECHANICS
(IF ANY): CE234 LAB
SYLLABUS:
UNIT DETAILS HOURS
Fluid properties - density – specific gravity – surface tension and
capillarity - vapour pressure - viscosity and compressibility -
Classification of Fluids (No questions to be asked). Fluid statics: Fluid
pressure, variation of pressure in a fluid, measurement of pressure
using manometers simple manometers, differential manometers,
I Pressure head. Forces on immersed plane and curved surfaces. 8
Pressure distribution diagram for vertical surfaces, Practical
application of total pressure (spillway gates). Buoyancy and
Floatation: Buoyant force, stability of floating and submerged bodies,
metacentre and metacentric height, Analytical and experimental
determination of metacentric height...
Kinematics of fluid flow: Methods of describing fluid motion,
Lagrangian and Eulerian methods, Types of fluid flow: steady and
unsteady flow, uniform and non-uniform flow, one, two and three
dimensional flow, laminar and turbulent flow, rotational and
irrotational flow. Types of flow lines: stream line, path line, streak
II lines, conservation of mass, equation of continuity in one, two and 8
three dimensions, (Derivation in Cartesian co-ordinate system only)
Velocity & Acceleration of fluid particle, convective and local
acceleration, Deformation of fluid elements: circulation and vorticity,
velocity potential, stream function, equipotential lines, flow net, uses
of flow net; Vortex motion, free and forced vortex (no problems).
Dynamic of fluid flow: Euler’s equation of motion and integration of
Euler’s equation of motion along a streamline. Bernoulli’s Equation,
III Energy correction factors, Applications of Bernoulli’s equation: Pitot
8
tube, Venturimeter and orifice meter. Momentum Principle- Steady
flow momentum equation- Momentum correction factor, Force
computation on a pipe bend
Flow through orifices: Different types of orifices, Flow over a sharp
edged orifice, Hydraulic coefficients – Experimental determination of
IV these coefficients, flow through large rectangular orifice, Flow 8
through submerged orifices, flow under variable heads, and time of
emptying. Flow over weirs: flow over rectangular, triangular and
Department of Civil Engineering, RSET C.2

UNIT DETAILS HOURS

trapezoidal sharp crested weir, Cipolletti weir, Broad crested weir,
Submerged weirs, Proportional weir
Flow through pipes: Viscous flow - Shear stress, pressure gradient
relationship - laminar flow between parallel plates - Laminar flow
V through circular tubes (Hagen Poiseulle's Eqn) - Hydraulic and
12
energy gradient - flow through pipes - Darcy -Weisbach's equation -
pipe roughness -friction factor- Moody's diagram- Major and minor
losses of flow in pipes - Pipes in series and in parallel.
Boundary layer theory-no slip condition, boundary layer thickness,
boundary layer growth over long thin plate, laminar, turbulent
boundary layer, laminar sub layer, Momentum integral equation of
VI boundary layer (no derivation), Blasius boundary layer equations for
12
laminar and turbulent boundary layer. Drag and lift on Immersed
bodies-Pressure drag and friction drag, profile drag, Drag and lift co-
efficient computation of drag on a flat plate. Separation of boundary
layer and control.
TOTAL HOURS 56
T1 Streeter V. L., Fluid Mechanics, Mc Graw Hill, International Students Edition
T2 Dr. P. N. Modi & Dr. S. M. Seth, Hydraulics and Fluid Mechanics, Standard Book
House Delhi.
T3 Jagdishlal, Fluid Mechanics & Hydraulics, Metropolitan Book Co., Delhi.
T4 R. J. Garde and A. G. Mirajoaker, Engineering Fluid Mechanics, Nem Chand &
Bross., Roorkee.
T5 Dr.D S Kumar,S K. “Fluid Mechanics and Fluid power Engineering”, Kataria&
Sons,NewDelhi
T6 Dr. R.K Bansal,A Text book of Fluid mechanics and Hydraulic machines, Laxmi
Publication
NIL

COURSE OBJECTIVES:
1 To understand the basic properties of the fluid, fluid statics, kinematics, and fluid
dynamics so as to analyse and appreciate the complexities involved in solving the
fluid flow problems.
2 To give an introduction to the fundamentals of fluid flow and its behaviour so as
to equip the students to learn related subjects and their applications in the higher
semesters.
3 To develop the skill for applying the fluid statics, kinematics and dynamics of fluid
flow concepts for solving civil engineering problems.
COURSE OUTCOMES:
Sl
No.
Understand the basics of fluid flow and pressure in fluids at rest
1
M
Analyse the condition of stability of a body in a fluid based on relative positions
2 of its centre of buoyancy and metacentre
H H
Analyse the condition of stability of a body in a fluid based on relative positions
3 of its centre of buoyancy and metacentre
M
Apply Bernoulli's equation to fluid flow problems involving venturimeter,
4 orifice meter, pitot tube, orifices, mouthpieces, notches and weirs
H M
Analyse the flow through pipes and the major and minor energy losses
5
H H
Understand the concept of development of boundary layer over a long thin
6 plate
M

The basics of fluid mechanics form the basis of the knowledge
CO1 PO1 MEDIUM of a Civil Engineer to encounter any problem in the field of
Water resources engineering
Stability of floating and submerged bodies in water is
PO1 HIGH essential engineering knowledge for those who aspire to
CO2 study fluid-structure interactions.
The student develops the ability to solve the problems on the
PO2 HIGH
stability of floating structures like ships and boats
The Civil Engineer needs to understand how to analyse a flow
CO3 PO1 MEDIUM
without having to consider the forces causing the motion

The simple methods that have been used to determine the
PO1 HIGH discharge and velocity of flow without using any electronic
equipment, helps build the logic of a Civil Engineer
CO4
The logic of the simple instruments like the venturimeter and
PO2 MEDIUM pitot tube can inspire the students to design similar simple
devices using the basic concepts of fluid flow.
The mechanics behind pipe flow and the energy losses
PO1 HIGH associated with it provides a fundamental engineering
CO5 knowledge to the student
Analysis of flow through pipes is a promising problem
PO2 HIGH
solving area in Civil Engineering
Boundary layer theory is a problem still awaiting a lot of
CO6 PO1 MEDIUM research and analysis and needs to be understood
thoroughly.

1 Derivation and numericals on free and forced vortex Seminars, NPTEL
flow

Sl No DESCRIPTION

Sl No DESCRIPTION
1 www.nptel.ac.in
LCD/SMART
BOARDS
ASSIGNMENTS
CERTIFICATIONS
ADD-ON
OTHERS
COURSES

OTHERS
Kavitha M Dr. Aysha Zeneeb Majeed

COURSE PLAN

Fluid properties - density, specific gravity, viscosity and
HOUR 1
compressibility
Surface tension and capillarity. Vapour pressure. Classification
HOUR 2 of fluids. Fluid pressure - variation of pressure in a fluid.
Measurement of pressure using manometers.
Definition of pressure head. Simple manometers, differential
HOUR 3
manometers.
HOUR 4 Problems on manometers. Forces on immersed plane surfaces.
HOUR 5 1 Problems on forces on immersed plane surfaces.
HOUR 6 Forces on curved surfaces. Spillway gates.
HOUR 7 Problems on spillway gates.
HOUR 8 Analytical determination of metacentre.
Buoyancy and floatation - buoyant force - problems. Concept of
HOUR 9
metacentre.
Experimental determination of metacentric height. Stability of
HOUR 10
floating bodies.
HOUR 11 Problems on metacentre.
Kinematics of fluid flow - Lagrangean and Eulerian methods of
HOUR 12
describing flow.
HOUR 13 Types of flow. Types of flow lines.
Conservation of mass. Equation of continuity in 1-D, 2-D and 3-
HOUR 14
D.
2
Velocity and acceleration of a fluid particle - convective and
HOUR 15
local acceleration.
HOUR 16 Deformation of fluid elements - circulation and vorticity.
HOUR 17 Velocity potential function, stream function
HOUR 18 Equipotential lines - flow net - vortex motion (free and forced)
Dynamics of fluid flow - Euler's equation of motion - Bernoulli's
HOUR 19
equation.
Energy correction factors. Applications of Bernoulli's equation
HOUR 20
- Pitot tube.
3 Applications of Bernoulli's equation - Venturimeter, Orifice
HOUR 21
meter.
HOUR 22 Momentum principle - steady flow momentum equation
Momentum correction factor - force computation in a pipe
HOUR 23
bend.
Flow through orifices - different types of orifices – hydraulic
HOUR 24
coefficients - experimental determination.

Flow over sharp edged orifice - flow through large rectangular

HOUR 25
orifice.
HOUR 26 Flow through submerged orifices - Flow under variable head.
HOUR 27 Time of emptying - problems.
HOUR 28 Flow over weirs - rectangular weir.
Flow over weirs - triangular, trapezoidal weirs - Cippoletti
HOUR 29
4 weir.
HOUR 30 Broad crested weir - submerged weir - proportional weir.
HOUR 31 Flow through pipes - Hagen Poiseulle equation.
HOUR 32 Hagen Poiseulle equation - problems
Darcy Weisbach equation - Major and Minor energy losses in
HOUR 33 5
pipes - Moody's Diagram.
HOUR 34 HGL and TEL
HOUR 35 Pipes in series and pipes in parallel.
Boundary layer theory - no slip condition - boundary layer
HOUR 36
thickness - boundary layer growth over long thin plate.
Laminar, turbulent boundary layer, laminar sublayer -
HOUR 37
momentum integral equation of boundary layer.
Blasius boundary layer equations for laminar and turbulent
HOUR 38 6
boundary layer.
Drag and lift on immersed bodies - pressure drag, friction drag,
HOUR 39
profile drag.
Drag and lift coefficient computation on a flat plate - separation
HOUR 40
of boundary layer and control.

ASSIGNMENT – I
All questions are compulsory
1. Prove that equipotential lines and stream lines are perpendicular to each other.
2. Given u = 2x2y + 3y, v = 5t - 2xy2. Determine the components of acceleration in
the X and Y directions.
3. Determine the velocity potential function if ψ = 3xy2
4. Differentiate between Lagrangian approach and Eulerian approach to analyse
fluid flow.

ASSIGNMENT – II
All questions are compulsory

1. Derive Darcy’s equation for head loss due to friction in pipe flow.
2. Two reservoirs with a difference in water surface elevation of 10 m are
connected by a pipeline ABC which consists of two pipes AB and BC joined in
series. Pipe AB is 10 cm in diameter, 20 m long and has a value of coefficient of
friction f = 0.005, pipe BC is 16 cm in diameter, 25 m long and has f = 0.0045.
a. Calculate the discharge
b. What difference in elevations is necessary to have a discharge of 15
litres/sec. Consider all minor losses.
3. A straight 25 cm diameter pipeline 5 km long is laid between two reservoirs
having a difference in level of 40 m. To increase the capacity of the system an
additional 2.5 km long 25 cm diameter pipe is laid parallel to the first from the
midpoint of the original pipe. Assuming friction factor 4f = 0.025 for both pipes,
find the increase in discharge due to installation of new pipe
4. A 30 cm diameter pipe is required for a town’s water supply. As pipes of this
diameter were not available in the market, it was decided to lay two parallel
pipes of equal diameter having equal lengths. Find the diameter of the parallel
pipes. Assume friction factor for both the pipes to be the same.
5. Two pipes of diameter 40 cm and 20 cm are each 300 m long. When the pipes are
connected in series and the discharge through the pipes is 100 litres/sec, find the
loss of head incurred. What would be the loss of head in the system for the same
discharge, if the pipes are connected in parallel? Take f = 0.0075 for each pipe.

UNITWISE QUESTION BANK

MODULE 1
1. Define density, specific weight and state their units
2. Define a fluid. Distinguish between an ideal and real fluid.
3. Explain Newton’s law of viscosity
4. Define surface tension.
5. State Pascal’s law. Give two examples where this principle is used.
6. Distinguish between absolute, vacuum and gauge pressure
7. Differentiate between a U-tube manometer and an inverted U-tube differential
manometer
8. Define total pressure and centre of pressure with a neat sketch
9. Define surface tension and capillarity, Derive an expression for capillary rise.
10. Explain the classification of fluids.
11. What is meant by surface tension? Derive expressions for pressure intensity inside
a liquid droplet, hollow bubble and a liquid jet.
12. Obtain an expression for pressure intensity at a point in a fluid.
13. Discuss the principle of working of a simple manometer
14. Define centre of pressure and centre of gravity of a body immersed in a liquid.
Show that the centre of pressure is always below the centre of gravity of the
immersed body.
15. Define the terms (i) Density (ii) Specific weight. State their units
16. State and explain Newton’s law of viscosity
17. State Newton’s law of viscosity and give examples of Newtonian fluids
18. State Newton’s law of viscosity and give examples of its applications
19. What is meant by viscosity of a liquid, how does it manifest and in what unit it is
measured?
20. Describe surface tension and capillarity as applied to a fluid
21. Obtain the expressions for the pressure intensity inside a droplet and a bubble.
22. How are fluids classified?
23. Differentiate between:
a. Ideal fluid and real fluid
b. Newtonian and Non- Newtonian fluid
24. State Newton’s law of viscosity. Explain the phenomenon of capillarity
25. Define and explain capillarity and surface tension of fluid.
26. Explain with neat sketch, the relationship between atmospheric, absolute and
gauge pressures.
27. Distinguish between gauge pressure and vacuum pressure.
28. What are the advantages of using mercury in manometers
29. Explain the working of a U-tube manometer.
30. Define and briefly explain total pressure and centre of pressure.
31. Sketch the section of a dam and indicate the forces indicating the resultant acting
on it

32. A plate having an area of 2 m2 drowns in an inclined plane at 45o to the horizontal,
with a velocity of 0.4 m/s. there is cohesion of fluid 1mm thick between the plate
and the plane. If the viscosity of the fluid is 0.1 Ns/m2, find the weight of the plate.
33. The bearing of an engine 10 cm diameter and 5cm long runs at 300 rpm. The
clearance between the bearing and shaft is 0.5 mm. The viscosity of the oil is 0.5
Ns/m2. Calculate the power lost in the bearing.
34. Define kinematic viscosity and dynamic viscosity. The space between 2 plates is
filled with oil. Size of the plate is 60cm x 60cm. Thickness of oil film is12.5mm. The
upper plate which moves at a speed of 2.5 m/s, requires a force of 0.1 kN to
maintain the speed. Determine the dynamic viscosity and kinematic viscosity of
the oil. Specific gravity of oil is 0.95.
35.
a. Distinguish between specific weight and mass density
b. A body weighing 450 N with a flat surface area of 0.1 m slides down a
lubricated inclined plane making 300 with the horizontal. If the sliding
velocity is 5m/s and the viscosity of the lubricant is 0.1 Ns/m2, determine
the lubricant film thickness.
36. Two large plane surface are 2.4 cm apart. The space between the surfaces is filled
with glycerine. What force is required to drag a very thin plate of surface area 0.5
m2 between the two large plane surfaces at a speed of 0.6 m/s? If (i) the thin plate
is middle of the two plane surface; and (ii) the thin plate is at a distance of 8 mm
from the bottom plane surface. Take the dynamic viscosity of glycerine as
0.810Ns/m2.
37. Derive an expression for the capillary rise of a liquid in terms of the surface
tension, σ and the contact angle, θ. If the diameter of the tube is 2mm and the
surface tension of the water in contact with air is 0.075 N/m, find the height to
which water will rise due to capillary action.
38. Explain the phenomenon of capillarity. Find the height through which water rises
by capillary action of a glass tube of 2mm diameter, if the surface tension of water
in contact with air is 0.075N/m
39. A rectangular plate of 0.5m x 0.5m dimensions weighing 500 N slides down an
inclined plane making 300 angle with horizontal, at a velocity 1.8 m/s. If the 2mm
gap between the plate and the inclined surface is filled with a lubricating oil, find
its viscosity.
40.
a. Mention some examples where compressibility of water is taken into
account.
b. Two horizontal flat plates are placed 0.15 mm apart and the space between
them is filled with an oil of viscosity 1 poise. The upper plate of area 1.5 m2
is required to move with a speed of 0.5 m/s relative to the lower plate.
Determine the necessary force and power required to maintain this speed.

41. State Newton’s law of viscosity. The space between two square flat plates of sides
720 mm is filled with oil of thickness 15 mm. The upper plate which moves at 3
m/s requires a force of 120 N to maintain the speed. Find
a. the dynamic viscosity of the oil
b. the kinematic viscosity of oil, if specific gravity of oil is 0.95
42. Define capillarity. Calculate the capillary effect in a glass tube of 4mm diameter,
when immersed in a) water b) mercury. The temperature of the liquid is 20o C,
and the corresponding surface tension for water and mercury in contact with air
are 0.073 N/m and 0.51 N/m respectively. Specific weight of water can be taken
as 9790 N/m3. Contact angle for water is 0o and for mercury is 130o.
43. There is a pin hole 0.1m in diameter at the bottom of a vessel containing Mercury.
What depth of Mercury can be put in the vessel without any leakage occurring?
Take ,=55N/m
44. Find the smallest diameter of a manometer tube such that error due to capillary
action in the measured gauge pressure of 100 N/m2 is less than 5%. The
manometric liquid is water.
45.
a. The surface tension of water in contact with air at 200C is 0.0725 N/m. The
pressure inside a droplet of water is to be 200 N/m2 greater than the
outside pressure. Calculate the diameter of the droplet of water.
b. The capillary rise in the glass tube is not to exceed 0.2 mm of water.
Determine its minimum size, given that surface tension for water in contact
with air is 0.0725 N/m.
46. Define pressure head and intensity of pressure. Find the head of water
corresponding to an intensity of pressure 100 N/cm2. The specific weight of water
is 10 kN/m3. Find the pressure of oil in a pipeline fitted with pressure tube and
reads a height of 1.5 m of oil. Specific weight of oil is 8.5 kN/m3
47. A pipe containing water at 172 kN/m2 pressure is connected by a differential
gauge to another pipe and containing water at high pressure. If the difference in
heights of two columns of mercury in the gauge is 75 mm, what is the pressure in
the lower pipe? Specific gravity of mercury=13.6
48. Distinguish between manometers and mechanical gauges. What are the different
types of mechanical pressure gauges?
49. Petrol of specific gravity 0.8 flows upwards through a vertical pipe. A and B are
two points in the pipe, B being 50 cm higher than A. Connections are led from A
and B to a U- tube containing mercury. If the difference of pressure between A and
B is 0.2 kg/cm2, find the reading shown by the differential mercury gauge.
50. A U-tube differential mercury manometer connects two pipes A & B. Specific
gravity of fluids A and B are 1.6 and 0.8 respectively and the fluid pressures are
120 kPa in A and 200 kPa in B. Pipe A lies 2.5 m above pipe B and the Mercury
level in the manometer limb connected to A is at the same level as the centre of
pipe B. Determine the difference in Mercury level indicated by the manometer.
51. State and explain practical applications of centre of pressure

52. Obtain an expression for the centre of pressure when a lamina is vertically
immersed in a liquid.
53. Derive an expression for the depth of centre of pressure of a plate lamina
immersed in a liquid at an angle θ to the free surface
54. Derive an expression for the depth of centre of pressure from free surface at liquid
of an inclined plane surface submerged in the liquid.
55. A circular observation window of 0.5m diameter is installed in an inclined tank
wall at 60o to the horizontal level. Water is 5m deep above the center of the
window. Determine the resultant hydrostatic pressure force on the window and
the centre of pressure.
56. A rectangular box with base 2.5m x 4 m is filled with kerosene oil of specific gravity
0.8, to a depth of 6m. Determine the resultant pressure and its point of application
on each vertical face of the box.
57. A triangular plate 1m base and 1.5 m altitude is immersed in water. The plane if
the plate is inclined at 30o with the free surface. The base is parallel to and at a
depth of 2m from the water surface. Find the total pressure on the plate and the
position of centre of pressure.
58. A pipeline 4m in diameter contains a gate valve. The pressure at the centre of the
pipe is 20 N/cm2. If the pipe is filled with oil of specific gravity 0.87, find the force
exerted by oil upon the gate and the position of centre of pressure.
59. A circular plate of diameter 1.5 m is placed vertically in water. The centre of the
plate is 3m below the free surface. Determine total pressure on the plate and the
position of centre of pressure, if the plate is inclined at 300 with free surface, the
centre of plate is inclined at 300 with the free surface, the centre of plate remaining
3m below the free surface.
60. A rectangular plate 0.5m x 0.5m dimensions weighing 400 N slides down an
inclined plane making an angle of 300 with horizontal, at a velocity of 1.5 m/s. If
the 2 mm gap between the plate and inclined plane surface is filled with
lubricating oil. Find its viscosity.
61. A gate 1m square lie in a plane making an angle of 300 with the vertical. Its upper
edge is horizontal and is 1.6 m below the liquid of specific gravity 1.5. Find the
resultant pressure on the gate and the location of the centre of pressure.
62. A square door whose dimensions 0.4m x 0.4m is provided on the vertical side of a
water tank. What force must be applied at the lower end of the gate so as to hold
hinged door closed? The hinged end which is at the top of door lies at a depth of
4m from surface of water. Also find the position of centre of pressure
63. A circular plane surface of diameter 4m immersed in water such that the top and
bottom edges are 1.5m and 4m below water surface. Find the total pressure force
and the position of centre of pressure from the water surface.
64. 10 litres of liquid of specific gravity 1.3 is mixed with 8 litres of a liquid of specific
gravity 0.8. If the bulk of the liquid shrinks 1% on mixing, calculate the specific
gravity, the density, the volume and the weight of the mixture

65. Why will a submarine always sink to the bottom of the ocean once it starts to sink
if no changes are made?
66. Explain metacentre and metacentric height.
67. Define and explain metacentric height
68. Explain buoyancy and centre of buoyancy.
69. Give the condition for stability of submerged and floating bodies.
70. What is metacentric height? Explain the analytical method for determining
metacentric height.
71. A ship displaces 40000 kN when floating in sea water with its axis vertical. A
weight of 4100 kN is placed on the centre line. Moving this weight by 1.2m towards
one side of the deck causes a plumb bob suspended from a 2.75m long string to
move by 300 mm. Find the metacentric height of the unloaded ship.
72. A cube of side ‘a’ floats with one side vertical in a liquid of relative density SL. If
the relative density of the cube material is SC, find the condition for metacentric
height to be zero.
73. A hollow wooden cylinder of specific gravity 0.6 has an outer dia. of 600 mm and
an inner dia. of 300 mm. It is required to float in an oil of specific gravity 0.9. Find
the maximum height of the cylinder, so that it will be stable when floating with its
axis vertical. Also find the depth of immersion.
74. A rectangular pontoon of weight 1500 kN floats in sea water. It is 15m long, 8m
wide and 4m deep. Find the metacentric height. The CG of the pontoon may be
taken as 0.15m, below the geometric centre. Assume specific weight of water as
10 kN/m3
75. Show that for a vertically submerged plane surface, the centre of pressure
approaches the centre of gravity as the depth of immersion increases.
76. A circular cylinder of 8 m diameter with bottom closed floats vertically with its
water line 4 m above the base. The centre of gravity of the body is 1.55m above
the base and on the vertical axis. Determine the metacentric height and limiting
height of the centre of gravity for stability.
77. A hollow wooden cylinder of specific gravity 0.56 has an outer diameter of 60 cm
and an inner diameter of 30cm. It is required to float in oil of specific gravity0.85.
Calculate the maximum height of the cylinder so that it shall be stable when
floating with its axis vertical.
78. A cylindrical buoy of weight 20 kN of diameter 2m and of height 2,5m is floating
in water of specific gravity 1.03. Its centre of gravity is 1.2m above the bottom.
Determine whether the buoy can float in stable equilibrium with its axis vertical.
If not, determine the tension in the chain required to make it stable, which is tied
at the bottom of the buoy and anchored to the sea bed
79.
a. Explain how metacentric height can be determined theoretically and
experimentally.

b. A uniform rectangular body 2m long, 1m wide and 0.8m deep floats in

water. The depth of immersion is 0.6m.What is the weight of the body? Find
the position of metacentre. Is it in stable equilibrium?
80. A rectangular contour weighing 910 kN floats in seawater. It is 2.2 m long and 7.6
m wide and 3m deep. Find the metacentric height. The C.G. of the contour may be
taken at its geometric centre.
81. A pipeline which is 4m in diameter contains a gate valve. The pressure at the
centre of the pipe is 20 N/cm2. If the pipe is filled with oil of specific gravity 0.87,
find the force exerted by the oil upon the gate and position of centre of pressure.
82.
a. Deduce an expression for the metacentric height of a floating body.
b. A wooden cylinder 3 m long and of 2m in diameter floats in water with its
axis vertical. The specific gravity of the wood is 0.6. Locate the position of
metacentre of the wooden cylinder. State the condition of equilibrium.
83. A solid cylinder is to be 0.25m in diameter. The base of axial length 25mm is of
material which has a specific gravity 0.7 and the remainder of the material which
has specific gravity 0.5. Find the maximum overall length of the cylinder inorder
that it may float in water in the stable equilibrium with its axis vertical.
84. A rectangular pontoon 12 m long, 9m wide and 3 m deep weighs 1380 kN and
floats in sea water of specific weight 10kN/m3. The pontoon carries on its upper
deck a boiler 6m diameter, weighing 864 kN. The centre of gravity of each unit and
geometric centre of arrangement lies in the same vertical plane. Find the
metacentric height and check whether the arrangement is stable.
85. Define the terms, “buoyancy and centre of buoyancy”. A wooden block of width
2m, depth 1.5m and length 4m floats horizontally in water. Find the volume of
water displaced and position of centre of buoyancy. The specific gravity of the
wooden block is 0.7.
86.
a. A cylinder has a diameter 0.3m and a specific gravity 0.75. What is the
maximum permissible length in order that it may float in water with its axis
vertical?
b. Explain the term metacentre and metacentric height.
MODULE 2
1. What are the conditions for flow to be irrotational
2. Define streamline, pathline and streakline
3. List the uses of flow nets.
4. Explain the methods of describing fluid motion.
5. Differentiate Lagrangian and Eulerian method
6. Explain stream function and velocity potential function.
7. Is the motion 𝑢 = 𝑥 2 𝑦, 𝑣 = 2𝑦𝑧 − 𝑥𝑦 2 and 𝑤 = 𝑥 2 − 𝑧 2 kinematically possible for
an incompressible fluid?
8. Prove that streamlines and equipotential lines meet orthogonally.

9. The stream function of a two dimensional flow is given by ψ=2xy. Calculate the
velocity at the point P(2,3).
10. Explain the importance of stream function
11. Define the flow net. What are its uses and limitations
12. Explain stream line, pathline, streakline and streamtube
13. Differentiate between : (a) Pathline and streamline (b) Rotational and irrotational
flow
14. Discuss the stability of floating bodies
15. Define the terms: (a) Velocity potential function (b) Stream function
16. Define a source, a sink and a doublet
17. What is meant by metacentric height? How it is related to the equilibrium of
floating body.
18. Derive the continuity equation for 3-D flow.
19. Can a function 𝜙 = 3𝑥𝑦 describe the flow of an incompressible fluid? If so,
determine the stream function. Determine the velocities at A(1,2) and B(2,2) and
the pressure difference between A and B. What is the discharge between the
streamlines through these points?
20. In a 3D incompressible flow, the velocity components in x and y directions are:
kx ky
u 3
and v  3
 x 2
 y 2
 z 
2 2
 x 2
 y 2
 z  .
2 2
21. Evaluate an expression for velocity component ‘w’ in the z-direction.

22. (a) Write an explanatory note on flow nets, their properties and uses.
23. A 2-dimensional steady velocity field is given by u=x2-y2, v=-2xy. Determine the
streamline pattern and sketch a few streamlines in the upper half plane.
24. Define stream line, streakline and stream tube. A 2- dimensional flow is described
by the velocity components u=5x3 and v=-15x2y. Evaluate the stream function,
velocity and acceleration at point P (x=1 cm & y=2m)
25. Define the stream function and velocity potential function. If for a 2- dimensional
potential flow, the velocity potential is given by, Φ =x(2y-1), determine the
velocity at the point P(4,5). Determine also the value of stream function ψ at the
point P.
26.
a. Prove that streamlines and equipotential lines meet orthogonally.
b. The velocity component in a flow field are given by:
u= ay sinxy v= ax sinxy.
Prove that the flow is irrotational and obtain expression for the velocity
potential function
27. Differentiate rotational and irrotational flow. Derive the continuity equation in
rectangular co-ordinates.
28. Define circulation and vorticity. Given u=xy, v=2yz. Check whether these
components represent 2 or 3 dimensional flow. If 3 dimensional, determine the
third component.

29.
a. The velocity potential for a two dimensional flow is Φ =x(2y-1), determine
the velocity at the point P(4,5). Determine also the value of stream function
ψ at the point P.
b. Is the motion u=x2y, v=2yz-xy2 and w=x2-z2kinematically possible for an
incompressible fluid.
30.
a. Describe the uses and limitations of the flow net
b. Under what conditions can one draw flow net
31. The velocity potential function is given by,
xy 3 x3 y
  [ ]  [ ]
3  x2 3 y2
a. Find the velocity component in x and y.

b. Show that  represents a possible case of flow.
32. Prove that equipotential lines and stream lines are perpendicular to each other.
33. Given u = 2x2y + 3y, v = 5t - 2xy2. Determine the components of acceleration in
the X and Y directions.
34. Determine the velocity potential function if ψ = 3xy
35. Differentiate between Lagrangian approach and Eulerian approach to analyse
fluid flow.
MODULE 3
1. What are the assumption in Bernoulli’s Equation
2. Derive Bernoulli’s equation for conservation of energy.
3. What is meant by Kinetic Energy Correction Factor and Momentum Correction
Factor? Derive expressions for the same.
4. Derive the expression for discharge through a venturimeter.
MODULE 4
1. What is a Cipolletti weir?
2. What is a weir? What is the difference between a weir and a notch
3. How are notches and weirs classified?
4. Compare a triangular notch with a rectangular notch for measuring discharges.
Deduce an expression for the discharge through a triangular notch
5. A submerged weir 1 m height spans the entire width 7m wide rectangular channel.
Find the discharge when the depth of flow on the upstream side is 1.8 m and on
the downstream side is 1.25 m.
6. Water flows over a right angled triangular weir of 1m width. If the discharge
coefficients are 0.6 and 0.7 for the triangular and rectangular weirs respectively,
determine the discharge over the weir if the head over the crest is 1.2m and the
velocity of approach is 2 m/s.

7. Deduce an expression for the discharge over a V-notch

8. Compare a triangular notch and rectangular notch. In a rectangular channel, the
discharge measured using a right angled V-notch from the bed of channel if the
maximum depth of water is not to exceed 1m. Assume Cd=0.62.
9. In an experiment on a 900 triangular notch, the discharge is collected in a circular
tank of 1m in diameter. The water level in the tank rises by 50 cm in 18 seconds.
The head over the notch is measured to be 20 cm. Determine the coefficient of
discharge. (Hint: Q=V/t. where t=18 sec, d=1m, h=.5m)
MODULE 5
1. Derive Darcy’s equation for head loss due to friction in pipe flow.
2. Two reservoirs with a difference in water surface elevation of 10 m are connected
by a pipeline ABC which consists of two pipes AB and BC joined in series. Pipe AB
is 10 cm in diameter, 20 m long and has a value of coefficient of friction f = 0.005,
pipe BC is 16 cm in diameter, 25 m long and has f = 0.0045.
a. Calculate the discharge
b. What difference in elevations is necessary to have a discharge of 15
litres/sec. Consider all minor losses.
(ANS: (a) 43.8 litres/sec; (b) 1.171 m)
3. A straight 25 cm diameter pipeline 5 km long is laid between two reservoirs
having a difference in level of 40 m. To increase the capacity of the system an
additional 2.5 km long 25 cm diameter pipe is laid parallel to the first from the
midpoint of the original pipe. Assuming friction factor 4f = 0.025 for both pipes,
find the increase in discharge due to installation of new pipe.
(ANS: 16.3 litres/sec)
4. A 30 cm diameter pipe is required for a town’s water supply. As pipes of this
diameter were not available in the market, it was decided to lay two parallel pipes
of equal diameter having equal lengths. Find the diameter of the parallel pipes.
Assume friction factor for both the pipes to be the same.
(ANS: 22.74 cm)
5. Two pipes of diameter 40 cm and 20 cm are each 300 m long. When the pipes are
connected in series and the discharge through the pipes is 100 litres/sec, find the
loss of head incurred. What would be the loss of head in the system for the same
discharge, if the pipes are connected in parallel? Take f = 0.0075 for each pipe.
(ANS: 6.15 m; 0.131 m)
6. Two pipes, each of length L and diameters D1 and D2 are arranged in parallel. The
loss of head when a discharge Q flows through them is H1. If the pipes are arranged
in series, and the same quantity of water Q flows through them is H2. If D1 = 2D2,
find H1/H2. Neglect minor losses and friction factor f is same for both pipes.
(ANS: 0.01654)
7. Derive the expression for pressure drop, which occurs due to viscous resistance,
across a section of a circular pipe.

8. For a laminar flow of an oil having dynamic viscosity 1.766 Ns/m2 in a 0.3m
diameter pipe, the velocity distribution is parabolic with maximum velocity 3 m/s
occurring at the centre of the pipe. Calculate the shear stress at the pipe wall and
within the fluid 50 mm from the pipe wall.
(ANS: 70.64 N/m2; 47.09 N/m2)
9. An oil flowing between two parallel plates kept at 10cm apart with maximum
velocity of 1.5 m/s. Find out the discharge per unit width of the plate, shear stress
at the plates and pressure difference between two points 20 m apart along the
direction of the flow. Also find out the velocity gradient at the plates and velocity
at 2 cm from the plate surface. Take viscosity of oil as 25 poise.
(ANS: 0.1 m3/s; 150 N/m2; 60 kN/m2;60 /s; 0.96 m/s)
10. The maximum velocity of the liquid passing through a pipe of 200 mm diameter is
2 m/s. Find the mean velocity and radius at which it occurs. Also find the velocity
at 40 mm from the wall of the pipe. Assume the flow is laminar.
MODULE 6
1. Determine the displacement thickness and momentum thickness in terms of the
nominal boundary layer thickness for the velocity profile in the boundary layer on
𝑢 𝑦 1 𝑚 𝑚 𝛿
a flat plate given by 𝑈 = (𝛿 )𝑚 . (ANS: 𝑚+1 𝛿; )
(𝑚+1) (𝑚+2)
2. The velocity distribution in laminar boundary layer over a flat plate is assumed as
u = a Sin(by) + c where a, b and c are constants. Apply the appropriate boundary
𝜋
conditions and determine the velocity distribution law. (ANS: a = U, b = 2𝛿 , c
= 0)
3. Calculate the friction drag on a plate 15 cm wide and 4.5 cm long placed
longitudinally in a stream of oil (S=0.925, υ = 0.9 stokes) flowing with a free stream
velocity of 6 m/s. Also find thickness of the boundary layer and shear stress at the
trailing edge.
(ANS: 13.7 N, 0.013 m, 63.77 N/m2)

4. A flat plate was positioned at zero incidence in a uniform flow stream of air.
Assuming boundary layer to be turbulent throughout the entire plate, work out
the ratio of skin-friction drag forces on the front and rear half part of the plate.
(ANS: 1.347)
5. A body of length 2 m has a projected area of 1.5 m2 normal to the direction of its
motion. The body is moving through water, which is having viscosity = 0.01 poise.
Find the drag on the body if it has a drag coefficient 0.5 for a Reynold’s no: 8 X 106.
(ANS: 6049 N)

6. A jet plane which weighs 29.43 kN and having a wing area of 20 m 2 flies at a
velocity of 950 km/hr, when the engine delivers 7357.5 kW power. 65% of the
power is used to overcome the drag resistance of the wing. Calculate the
coefficients of lift and drag for the wing. The density of atmospheric air is 1.21
kg/m3.
(ANS: CD = 0.0215; CL = 0.0349)

D
CE 205
ENGINEERING GEOLOGY

SEMESTER: S3
COURSE: ENGINEERING GEOLOGY
COURSE CODE: CE205
COURSE TYPE: CORE
REGULATION: 2015
CONTACT HOURS: 3+1 hours/Week.
ENGINEERING
(IF ANY): NIL
SYLLABUS:
UNIT DETAILS HOURS
Relevance of geology in Civil Engineering. Subdivisions of Geology.
Weathering, types and its engineering significance. Laboratory tests
I used in civil engineering for assessing intensity of weathering. 8
Engineering classification of weathered rock masses. Soil profile.
Geological classification of soils..
Hydrogeology-occurrence of groundwater, Types of aquifers,
permeability / hydraulic conductivity. Engineering significance of
II subsurface water problems created in construction, as an erosional 11
agent. Methods to control of subsurface water barriers and liners,
drains and wells. (Resistivity survey of groundwater may be
demonstrated).
Minerals- Properties that affect the strength of minerals. Physical
properties and chemical composition of following minerals -quartz,
feldspars (orthoclase and plagioclase), micas (biotite and muscovite),
III amphibole (hornblende), pyroxene (augite and hypersthene), 8
gypsum, calcite, clay minerals (kaolinite), their chemical formulae.
Earth quakes- in relation to internal structure of earth and plate
tectonics.
Rocks as aggregates of minerals. Basic concepts igneous, sedimentary
and metamorphic rocks, Brief account of following rocks- granite,
basalt, sandstone, limestone, shale, marble and quartzite. Rock
features that influence the strength of rocks as construction material-
IV concepts of lineation and foliation-schistosity and gneissosity. Rock 10
types of Kerala. Brief account of engineering properties of rocks used
as construction material (building and foundation) and road
aggregates. Assessment of these properties.(Students should be
taught to identify common rock forming minerals and common rocks
based on their physical properties).
Attitude of geological structures- strike and dip. Brunton compass.
Deformation structures and their engineering significance- folds,
V faults and joints. Geological factors considered in the construction of 11
dams and reservoirs, tunnels. (Simple exercises based on
geological/topographic maps for determination of dip, apparent dip
Department of Civil Engineering, RSET D.2

UNIT DETAILS HOURS

and thickness of lithological beds and preparation of geological cross
sections should be performed. The students should instructed in
handling clinometer/Brunton compass to determine strike and dip)
Introduction to natural hazards-Mass movements (Landslides),
floods, their common management strategies. Coastal Processes-
VI waves, currents and landforms. Types of coastal protection 8
strategies. Soil erosion- causes and types and soil conservation
measures.
TOTAL HOURS 56
T1 Duggal, SK,Rawal,N and Pandey, HK (2014) Engineering Geology, McGraw Hill
Education, New Delhi
T2 Garg, SK (2012) Introduction to Physical and Engineering Geology, Khanna
Publishers, New Delhi
T3 Gokhale, KVGK (2010) Principles of Engineering Geology, BS Pubications,
Hyderabad
T5 Kanithi V (2012) Engineering Geology, Universities Press (India) Ltd.,
Hyderabad
T6 Singh, P (2004) Engineering and General Geology, S. K. Kataria and Sons, New
Delhi
T7 Gokhale, NW (1987) Manual of geological maps, CBS Publishers, New Delhi
MATHEMATICS FUNDAMENTAL KNOWLEDGE OF SECONDARY
TRIGONOMETRY SCHOOL LEVEL
PHYSICS BASIC KNOWLEDGE ABOUT PLUS-TWO
FRICTION, DENSITIES AND UNIT
WEIGHTS.
CHEMISTRY FUNDAMENTAL KNOWLEDGE PLUS-TWO
ABOUT MATERIAL PROPERTIES
COURSE OBJECTIVES:
1 Awareness about earth resources and processes to be considered in various facets
of civil Engineering.
2 Appreciation of surface of earth as the fundamental foundation structure and the
natura phenomena that influence its stability.

COURSE OUTCOMES:
Sl
No.
The students will be able to explain the relevance of Engineering Geology in
1 Civil Engineering.
L
The students will be able to classify the different weathering processes.
2
L L
The students will be able to explain the concepts of subsurface water and its
3 engineering significance.
L
The students will be able to interpret earthquakes in relation to internal
4 structure of the earth
L
The students will be able to identify common rock forming minerals and
5 common rocks based on their physical properties.
H M
The students will be able to identify the attitude of geological structures and
6 instruments used
H
The students will be able to distinguish various natural hazards and its
7 mitigation methods.
H

Students will be able to apply the knowledge from
CO1 PO6 LOW engineering geology to solve the problems affecting the
society and take relevant measures to ensure the safety.
Students will be able to solve the complex engineering

problems regarding the availability of raw materials for
PO1 LOW construction and find suitable alternatives for the materials
CO2 that are scarce.
Properties of the existing land condition forms the

PO3 LOW fundamental prerequisite for any design.
The study of subsurface water and its engineering

significance in construction allows students to create
CO3 PO3 LOW awareness among people about various sources of water and
how it can affect the various fields of construction and the
stability of structures.

PO3 LOW The students shall interpret the various causes and effects
CO4 of earthquakes and shall develop solutions to minimise the
effects of earthquake.
PO1 HIGH Students will be able to solve the complex engineering

problems regarding the availability of raw materials for
construction by studying the properties and composition of
various materials and minerals and find suitable
alternatives for the materials that are scarce.
CO5
PO2 MEDIUM Identifying each mineral with respect to their physical
properties helps students to classify the types and
properties of rocks and their suitability in various fields of
engineering.
CO6 PO1 HIGH The knowledge of using various instruments helps the
students to analyse various features on the earth and the
attitude of geologic structures helps the students to analyse
the complex engineering activities of the structures.
CO7 PO6 HIGH By studying the various natural hazards, its causes,
remedies and prevention can help students to tackle the
occurrence of adverse situations in society.

1 Crystallography of minerals NPTEL
2 Unconformity NPTEL

Sl No DESCRIPTION
1 Hydrologic cycle
2 Slope stability

Sl No DESCRIPTION
1 www.nptel.ac.in
LCD/SMART
BOARDS

ASSIGNMENTS
CERTIFICATIONS
ADD-ON
OTHERS
COURSES
OTHERS
Aswathy G Dr. Aysha Zeneeb Majeed

COURSE PLAN

introductory class, various features existing on the surface of
HOUR 1
earth
HOUR 2 Relevance of geology in civil engineering
HOUR 3 subdivisions of geology
HOUR 4 weathering and its types
HOUR 5 1 weathering and its types
HOUR 6 engineering significance of weathering
HOUR 7 laboratory tests for determining the intensity of weathering
HOUR 8 geological classification of soil
engineering classification of weathered rock masses and soil
HOUR 9
profile
HOUR 10 hydrogeology and types of aquifer
permeability and hydraulic conductivity, occurrence of ground
HOUR 11
water
engineering significance of subsurface water created as
HOUR 12
2 erosional agent
methods to control subsurface water, liners, barriers, drains
HOUR 13
and wells
HOUR 14 drains and wells contd..
HOUR 15 resistivity survey of ground water
HOUR 16 Introduction to Minerals (occurrence, types of bonds etc.)
HOUR 17 properties that affects the strength of minerals
HOUR 18 properties that affects the strength of minerals continued
HOUR 19 physical properties and chemical composition of quartz
physical properties and chemical composition of feldspars
HOUR 20
(orthoclase and plageoclase)
physical properties and chemical composition of micas and
HOUR 21
amphibole
3
physical properties and chemical composition of pyroxene and
HOUR 22
gypsum
physical properties and chemical composition of calcite and
HOUR 23
clay minerals
earthquakes in relation to internal structure of the earth –
HOUR 24
earthquake and causes
HOUR 25 to internal structure of the earth
HOUR 26 plate tectonics
HOUR 27 4 rocks as aggregates of minerals- introduction
HOUR 28 basic concepts of igneous and sedimentary rocks
HOUR 29 basic concepts of metamorphic rocks
HOUR 30 brief account of granite and basalt
HOUR 31 brief account of sandstone and limestone
HOUR 32 brief account of shale, marble and quartzite
rock features that influence the strength of rocks as
HOUR 33
construction material
HOUR 34 concept of lineation and foliation

HOUR 35 concept of schistosity and gneissosity

HOUR 36 rock types of kerala
engineering properties of rocks used as construction material
HOUR 37
and road aggregates
HOUR 38 engineering properties of rocks used as road aggregates
HOUR 39 attitude of geological structures- strike and dip
HOUR 40 brunton compass and its features
HOUR 41 deformation structures and engineering significance of folds
deformation structures and engineering significance of faults
HOUR 42
joints
HOUR 43 5 deformation structures and engineering significance joints
HOUR 44 geological factors considered in the construction of dams
geological factors considered in the construction of reservoirs
HOUR 45
and tunnels
practical - determination of dip, apparent dip, lithological beds
HOUR 46
etc
HOUR 47 introduction to natural hazards (brief introduction)
mass movements (landslides) and their management
HOUR 48
strategies
HOUR 49 floods and their management strategies
HOUR 50 coastal processes- waves and currents
HOUR 51 coastal processes- landforms
HOUR 52 6 types of coastal protection strategies
HOUR 53 soil erosion- causes and types
HOUR 54 soil erosion- causes and types

HOUR 55 soil conservation measures
HOUR 56 Revision

ASSIGNMENT 1
Maximum Marks 10
1. Explain the geological classification of soils. (2.5m)
2. Detail the problems created by subsurface water in construction. (2.5m)
3. Deliver a lecture on various minerals assigned to you. (5m)
To be submitted on September 5th, 2018
ASSIGNMENT 2
Maximum Marks 10
1. Explain the major rock species outcropped in Kerala.
2. Write short note on unconformity and its engineering significance.
3. Write short note on slope stability and its causes. How is it related to landslides?
To be submitted on November 9th, 2018

UNIT WISE QUESTION BANK

MODULE 1
PART A
1. Define engineering geology.
2. Define weathering.
3. What is meant by seismic zone?
4. What is physical weathering?
5. What is chemical weathering?
6. What is spheroidal weathering?
7. Define exfoliation.
PART – B
1. Explain in detail about weathering of rocks and its engineering importance.
2. Write in detail about the scope of geology and importance of geology in Civil
Engineering.
3. Explain physical and chemical weathering process in detail. Add a note on
weathering grade and its engineering significance.
4. Explain the process associated with river. Write their engineering significance.
5. Explain the process associated with winds. Write their engineering significance.
6. Explain the process associated with sea. Write their engineering significance
MODULE 2
PART A
1. Differentiate between water table and perched water table.
2. Define aquifer and mention its types.
3. What is meant by subduction zone? Mention its importance.
4. Differentiate aquifer and aquiclude.
5. Write about Mercalli scale.
6. Describe the interior of the earth.
7. Define confined aquifer.
8. Define unconfined aquifer.
9. Mention the seismic zones of India.

PART B
1. Write in detail about the structure of the earth and its composition with a neat
diagram.
2. Give an account on mode of occurrence and prospecting of ground water.
3. Describe in detail about plate tectonics.
4. Explain in detail about the earthquake belts of India.
MODULE 3
PART A
1. Define mineralogy.
2. Define hexagonal, isometric, tetragonal, orthorhombic, triclinic, monoclinic
system of crystals.
3. Write the physical properties of mica.
4. Define mineral.
5. What are the different physical properties of minerals?
6. Give the physical properties and uses of quartz, augite.
7. What is moh’s scale of hardness?
8. Give the physical properties and uses of hornblende, biotite.
9. Name at least 4 clay minerals and their important engineering properties.
10. Give the physical properties of muscovite, calcite.
11. Define tetragonal system of crystals.
12. Define orthorhombic system of crystals.
13. Define triclinic system of crystals.
14. Define monoclinic system of crystals.
15. Define colour.
16. Define lusture.
17. Define form,streak.
18. Define hardness, fracture and specific gravity.
PART B
1. Elaborate the various physical properties which help in identification of minerals.
2. Explain the physical properties of Feldspar group of minerals.
3. Explain the physical properties of Quartz group of minerals.
4. Explain the physical properties of Augite, hornblende.

5. Explain the physical properties of Mica group of minerals.

6. Explain the physical properties biotite, calcite.
MODULE 4
PART A
1. Define petrology.
2. Write the classification of petrology.
3. What are metamorphic rocks?
4. What are igneous rocks?
5. What are sedimentary rocks?
6. Write about the occurrence of granite.
7. Write about the occurrence of basalt.
8. Classify igneous rocks.
9. Classify metamorphic rocks.
10. Write the composition uses of shale, slate and marble.
11. Write about the structure of igneous rocks.
12. Write about the occurrence of sandstone.
13. What are the factors controlling the specific gravity, porosity and strength of
rocks?
14. List out the tests to be carried out to determine the strength of building stones.
15. What is black granite? List its uses.
16. Bring out the differences between granite and slate.
17. What is ductility of rocks?
18. Describe the uses of black granite.
19. How igneous rocks are classified according to their occurrences?
PART B
1. What are sedimentary rocks? Explain the properties of any 4 sedimentary rocks.
2. What are metamorphic rocks? Explain the properties of any 4 metamorphic rocks.
3. What are igneous rocks? Explain the properties of any 4 igneous rocks.
4. Describe the engineering properties of rocks.
5. Describe the different types of rocks. Give the classification, texture and structure
of igneous, sedimentary and metamorphic rocks.

6. List the various field and laboratory tests to determine the engineering properties
of rocks.
7. Describe in detail about the mineral composition, structure, texture, origin,
engineering properties and uses of basalt, dolerite, sandstone and slate.
8. Describe the composition, texture, characteristics, occurrence and uses of black
granite and basalt
9. Describe the composition, texture, characteristics, occurrence and uses of
limestone and slate.
10. Describe the engineering properties of igneous rocks.
MODULE 5
PART A
1. Define structural geology.
2. Define dip and strike.
3. Define recumbent fold and overturn fold.
4. Differentiate anticline and syncline.
5. Describe wenner’s configuration of electrodes.
6. What are joints? Explain their significance.
7. What are folds? Explain their significance.
8. What are faults? Explain their significance.
9. Differentiate Wenner and berger methods.
10. Define outcrops.
11. What are true and apparent dips?
12. What are the types of dips?
13. What is a geological map?
14. Draw and describe the parts of folds.
15. Classify folds.
16. Write the causes of foldings?
17. What are the engineering considerations of a fold?
18. What are the engineering considerations of a fault?
19. What are the mechanisms of faulting?
20. Write about the origin of joints.

PART B
1. What is a fault? Discuss the various types of faults and write about the engineering
applications.
2. What is a fold? Discuss the various types of faults and write about the engineering
applications.
3. What is a joint? Discuss the various types of faults and write about the engineering
applications.
4. Explain in detail the role of electrical methods of subsurface investigation in civil
engineering practice.
5. Describe seismic refraction survey to de conducted for determining the depth of
bed rock.
6. Discuss in detail electrical method of investigation for ground water exploration.
7. Classify folds and faults in rocks and explain how they influence the design of
dams.
8. Classify and describe joint structures with neat sketches and also write their role
in dam and tunnel construction.
9. Give a detailed account of the various geological structures and their role in
selection of sites for engineering projects.
10. Describe fault structures with neat sketches and also write their role in dam and
tunnel construction.
MODULE 6
PART A
1. List a few measures of coastal protection.
2. What is the function of groynes in coastal protection?
3. Enumerate the coastal protection structures.
4. What is the application of satellite imagery?
5. Define overlap.
6. Define overbreak.
7. Describe sea wall and jetties in coastal protection structures.
8. List any 4 methods to prevent landslides.
9. Define stand up time in dam construction.
10. Define pay line in dam construction.

11. Differentiate swelling ground and running ground in construction site.

12. Define the term parallax in aerial photograph.
13. What are the various types of aerial photographs?
14. Explain how the study of bed rocks is essential before the construction of tunnels.
15. Define overbreak and pay line in tunnelling operations.
16. Write the applications of remote sensing techniques.
17. What are multipurpose dams?
18. Give the functions of breakwater.
PART B
1. Write in detail about landslides and their causative effects. Explain about the
measures to prevent them.
2. What are the various geological factors to be considered for the construction of
dams? Explain with examples.
3. Explain in detail the role of aerial photographs and satellite images in planning
and execution of civil Engineering projects.
4. Write in detail about sea erosion and coastal protection structures.
5. Using case studies, describe the various aspects of coastal erosion and the various
methods of coastal protection.
6. What are the various geological factors to be considered for the construction of
tunnels? Explain in detail with examples.
7. What are the various geological factors to be considered for the construction of,
road cuttings? Explain in detail with examples.

E
CE 207
SURVEYING

SEMESTER: S3
COURSE: SURVEYING
COURSE CODE: CE207
COURSE TYPE: CORE
REGULATION: 2016
ENGINEERING
LAB COURSE NAME: SURVEYING LAB
(IF ANY): CE 233
SYLLABUS:
UNIT DETAILS HOURS
Introduction to surveying- Principles, Linear, Angular and graphical
I methods, Survey stations, survey lines- ranging, Bearing of survey 6
lines- local attraction, declination, dip, Latitude and Departure,
Methods of orientation, Principle of resection
Levelling: Principles of levelling- Dumpy level- booking and reducing
II levels, methods- simple, differential, and reciprocal levelling- profile 7
and cross sectioning. Digital and Auto Level, Errors in levelling.
Contouring: Characteristics, methods, uses
Area and Volume: Various methods of computation.
III Theodolite survey: Instruments- measurement of horizontal and 7
vertical angle. Mass diagram: Construction, Characteristics and Uses
Triangulation: Triangulation figures, Strength of figure, Triangulation
IV stations, inter visibility of stations, Towers and signals – Satellite 7
Stations and reduction to centre.
Theory of errors – Types, theory of least squares, weighting of
V observations, most probable value, application of weighting, 8
computation of indirectly observed quantities, Method of normal
equations
Electromagnetic distance measurement (EDM) – Principle of EDM,
Modulation, Types of EDM instruments, Distomat
VI Total Station – Parts of a Total Station – Accessories – Advantages and 7
Applications, Introduction to Astronomical terms, Field Procedure for
total station survey, Errors in Total Station Survey
TOTAL HOURS 42
T1 Dr. B. C. Punmia , Ashok kumar Jain & Arun Kumar Jain - Surveying , Laxmi
publications (P)Ltd , 2005
T2 S. K. Duggal - Surveying Vol. I, Tata Mc Graw Hill Ltd ,Reprint2015
Department of Civil Engineering, RSET E.2


R1 Prof. T. P. Kenetkar & Prof. S. V. Kulkarni - Surveying and Levelling , Pune
Vidyarthi Griha Prakashan,2004
R2 R. Agor - A Text book of Surveying and Levelling, Khanna Publishers, 2005
R3 C. Venkatramaiah, Textbook of Surveying, Universities Press (India) Private
Limited 2011
R4 James M. Andersen, Edward M Mikhail, Surveying Theory and Practice, McGraw
Hill education
CE110 Civil Engineering Method of surveying S1/ S2
Workshop Classification of Surveying
COURSE OBJECTIVES:
1 To introduce the principle of surveying
2 To impart awareness on the various fields of surveying and types of instruments
3 To understand the various methods of surveying and computations
COURSE OUTCOMES:
Sl
No.
Student could compare the knowledge of the basic and conventional surveying
1
M
Student could determine the heights of different terrains through method of
2 Contouring
H
Students could apply the knowledge of calculations of area and volume of the
3 earth works in field of study
H M L
Students could demonstrate how the given field should be divided into known
4 figures in order to do the survey
M
Students could evaluate how accurate the data is which are obtained from the
5 survey by studying the different types of errors
H H
Student could extend the study of surveying from conventional methods and
6 instruments used
M L


The basics used in survey form the basis of the knowledge of
CO1 PO1 MEDIUM a Civil Engineer to encounter any problem in the field of
Surveying
Modern tools are introduced day by day. So we need to have
CO2 PO5 HIGH knowledge on different instruments used for surveying and
how it will useful when new updates comes
Basic knowledge of how area and volume can be calculated
PO1 HIGH
on a given plot or between the given points on ground
CO3 By different methods of calculation of area and volume any
PO2 MEDIUM
complex problems can be solved in surveying
PO3 LOW We can design and develop solutions of any kind of surveys
Identify or analyse any kind of surveying problem which
CO4 PO2 MEDIUM
comes under triangulation surveying
Applying the knowledge of errors thus by adjusting the
PO1 HIGH
triangulation figures in order to get proper results of survey
CO5 With the help of measurements taken from the field we can
PO3 HIGH design solutions for complex states of surveying like
triangulations
With the help of sophisticated different instruments one can
PO1 MEDIUM one can find solution for any complex problems related to
surveying
CO6
Modern tools are introduced day by day. So we need to have
PO5 LOW knowledge on different instruments used for surveying and
how it will useful when new updates comes

1 How triangulation is being done on a large NPTEL video
country – Base Net
2 Land Surveying Vs Hydrological Surveying NPTEL video

Sl No DESCRIPTION
1 Importance of surveying in oil and gas companies
2 Hydrological Surveying
3 Survey in field of Mining
4 Importance of GIS & Remote Sensing


Sl No DESCRIPTION
1 http://nptel.ac.in/courses/105104101/
2 http://nptel.ac.in/courses/105107122/home.htm
3 https://www.youtube.com/watch?v=hc5-Flo-
0i8&list=PLX76DrtWfjnlz1OuwsLIpmmdrB5j9KdXr
4 https://www.youtube.com/watch?v=chhuq_t40rY&list=PLE29B77BFD3B8D
70B
LCD/SMART
BOARDS
ASSIGNMENTS
CERTIFICATIONS
ADD-ON
OTHERS
COURSES
OTHERS
Bibin Hezakiel V. Dr. Aysha Zeneeb Majeed

COURSE PLAN

HOUR 1 Introduction to surveying- Principles
HOUR 2 Linear, Angular and graphical methods
HOUR 3 Survey stations, Survey lines- Ranging, Bearing of survey lines
1
HOUR 4 Local attraction and numerical problems related
HOUR 5 Declination, Dip, Latitude and Departure
HOUR 6 Methods of orientation, Principle of resection
HOUR 7 Levelling: Principles of levelling- Dumpy level
HOUR 8 Booking and reducing levels
HOUR 9 Reducing levels, methods
Types of Levelling - Simple, differential, and reciprocal
HOUR 10
2 levelling
Profile and Cross Sectioning -Digital and Auto Level, Errors in
HOUR 11
levelling
HOUR 12 Contouring: Characteristics, Methods
HOUR 13 Contouring: uses
HOUR 14 Area and Volume: computation
HOUR 15 Theodolite survey: Instruments
HOUR 16 Measurement of horizontal
3
HOUR 17 Measurement of vertical angle
HOUR 18 Mass diagram: Construction
HOUR 19 Mass diagram: Characteristics and Uses
HOUR 20 Triangulation : Triangulation figures
HOUR 21 Strength of Figure
HOUR 22 Triangulation stations
HOUR 23 4 Intervisibility of stations
HOUR 24 Towers
HOUR 25 Signals
HOUR 26 Satellite Stations & Reduction to center
HOUR 27 Theory of errors
HOUR 28 Types and theory of least squares
HOUR 29 Weighting of observations
HOUR 30 5 Most Probable Value
HOUR 31 Application of weighting
HOUR 32 Computation of indirectly observed quantities
HOUR 33 Method of Normal Equations
Electromagnetic Distance Measurement - Principle of EDM,
HOUR 34
Modulation
HOUR 35 Types of EDM instruments - Distomat
HOUR 36 Total Station – Parts of a Total Station
6
HOUR 37 Accessories & Advantages and Applications
HOUR 38 Field Procedure for total station survey
HOUR 39 Errors in Total Station Survey
HOUR 40 Introduction to Astronomical terms

ASSIGNMENT 1
1. Briefly explain the how different methods where useful in the field of Plane
Tabling
2. Write short notes on
a. Digital Level
b. Auto Level
3. What are the Uses of Contouring? Explain briefly the different Methods.
4. Explain in a paragraph the importance of survey in i) Oil and Gas ii) Hydrology
5. How triangulation is being done on a large country?
To be submitted on September 7th, 2018
ASSIGNMENT II
1. Write short notes on EDM instruments
2. Explain how Probable errors are determined when
a. Direct observations of equal weight on a single unknown quantity.
b. Direct observations of unequal weight on a single unknown quantity.
c. Computed Quantity.
3. Explain briefly about any application in GIS in the field of Civil Engineering.
4. What are the applications of Total Station?
5. What are the errors of Total Station?
To be submitted on November 1st, 2018

QUESTION BANK
MODULE I
1. Tabulate the differences

a. Fore Bearing and Back Bearing
b. QB and WCB
c. TB and MB
d. Isogonic and agonic lines
e. Isoclinic and aclinic lines
f. Declination and dip
g. Prismatic compass and surveyor’s compass
2. Define the following or write short notes on
a. True Meridian (TM)
b. Local Attraction (LA)
c. Magnetic declination
d. Dip of needle
3. Why is it necessary to plot maps with TB than MB?
4. Sketch and describe the features of prismatic compass
5. Sketch and describe the features of surveyor’s compass
6. What is meant by Local Attraction? How is it detected and explain how local
attraction is eliminated?
7. What do you mean by a traverse? Types?
8. What do you understand by plane table survey?
9. Explain the principle of plane table surveying?
10. What are the methods of plane surveying?
11. Explain
a. Radiation
b. Intersection
c. Traversing
d. Resection
12. Explain the differences between the above methods
13. What are the advantages and disadvantages of Plane Tabling?
14. List the different accessories used in plane tabling along with their uses?
15. Explain the errors in plane table surveying
16. Explain Method of resection
Module II
17. What are the advantages and disadvantages of dumpy level?

18. Define the terms
a. Line of collimation
b. Height of instrument

c. Back sight
d. Intermediate sight
e. Fore sight
f. Reduced level
g. Bench marks – different types
h. Level line
i. Level surface
j. Horizontal plane
k. Horizontal line
l. Elevation
m. Turning point
19. What are the instruments used in leveling?
20. What are the temporary adjustments of a level?
21. What are the types of leveling?
22. What do you mean by spirit leveling or Direct Leveling?
23. Explain Differential Leveling
24. Explain profile leveling
25. Explain cross sectioning
26. Explain reciprocal leveling
27. Differences between HI method and Rise and Fall method
28. What do you mean by curvature and refraction correction?
29. What is combined correction?
30. What do you mean by distance to visible horizon?
31. Explain the errors in Leveling
32. Explain the sensitivity of bubble tube
a. Contour
b. Contouring
c. Contour interval
d. Horizontal equivalent
34. What are the considerations on which the choice of proper contour depends on?
35. What are the characteristics of contour?
36. What are the uses of contour maps?
37. What are the methods by which contour can be done?
MODULE III
38. What do you mean by face right face left of a theodolite? How would you change
face? What instrumental errors are eliminated by doing so?
39. Describe the temporary adjustments of a theodolite. Explain how you measure
a. horizontal angle
b. vertical angle
c. bearing of a line

40. Sketch the fundamental lines of a theodolite. State the relation between them
41. Differentiate between
a. Face left and Face right
b. Telescope normal and telescope inverted
c. Transiting and swinging telescope
42. Explain the method of repetition
43. Explain the method of reiteration
44. State what errors are eliminated by the following
a. Face left and face right observation
b. Reading both the verniers
c. Repetition method by horizontal angle
45. Describe how a theodolite is set up at a station and a round of angles is measured
at it? What errors are minimized in this procedure?
46. State and prove trapezoidal and prismoidal rule
47. Discuss the various methods of measurements of area by offsets from base line
48. Describe planimeter?
49. What do you mean by zero circle of planimeter?
50. How area can be measured by planimeter?
51. What do you mean by prismoid? Derive prismoidal formula
52. Derive an expression for trapezoidal formula for volume
53. Explain with neat sketches the use of a contour map for calculation of earth
works?
54. How do you determine the capacity of a reservoir?
55. Derive expressions for side widths and areas of
a. level section
b. two level section
c. three level section
d. multi-level section
56. Define prismoidal correction? obtain an expression for it
57. Explain in detail mass curve?
58. Explain the construction of mass curve?
59. What are the uses of mass curve?
60. What are the characteristics of mass curve?
MODULE IV
61. What is triangulation? Why triangulation is important in surveying?

62. What is a triangulation system?
63. How triangulation system is classified?
64. What do you mean by a triangulation figure? How are they classified?
65. What are the criteria for selection of triangulation figure?
66. What do you mean by strength of figure?
67. What are the steps in Triangulation survey?

68. Explain reconnaissance in triangulation survey

69. How do you determine the intervisibility of triangulation stations?
70. Explain McCaw’s Method with a neat sketch
71. Explain
a. Station Marks
b. Phase of Signal
c. Phase Correction
d. Normal Tension
e. Satellite station
f. Reduction to centre
g. Base Net
72. Write a short note on Signals and Towers
73. Explain the different types of signals with their merits and demerits
74. Discuss the effect of phase in sighting a sun signal and show with neat sketches
how it may be eliminated or reduced
75. Derive formula for the correction to be applied to cylindrical signals i) When the
bright portion is bisected ii) When the bright line is bisected
76. Explain how the selection of base line is done or what are the principles objects
to be kept in view in selecting the ground for a base line in large survey?
77. Explain the instruments used for measuring the Base Line
78. Lists out the corrections applied for the base line measurements
79. Explain the tape corrections or explain the corrections to be applied in base line
measurements
80. Explain the instruments used in measuring the horizontal angles
81. Explain the methods of observation of horizontal angles
82. What is meant by satellite station and reduction to centre? Derive an expression
for reducing the angles measured at the satellite station to the centre
83. What is meant by eccentricity of signal? How would you correct the observation
when made upon an eccentric signal? State the reasons for using a satellite
station in triangulation survey
84. Derive the formula used for reducing the angles measured at satellite stations to
center
MODULE V
85. Explain the different types of errors
a. Independent Quantity
b. Conditioned Quantity
c. Direct observation
d. Indirect observation
e. Weight of an observation
f. Observed value of a quantity

g. True value of a quantity

h. MPV
i. True error
j. Most Probable Error
k. Residual Error
l. Observation Equation
m. Conditioned Equation
n. Normal Equation
87. Explain the laws of accidental errors
88. What do you mean by the principle of Least Squares?
89. Explain the laws of weights
90. Explain how probable error can be determined
91. What are the rules applied for the distribution of error to the field
measurements?
92. Explain the method of Normal Equation
93. Explain the Direct method for determining the MPV values
94. Explain the method of Differences for determining the MPV values
95. Explain the method of Correlates for determining the MPV values
MODULE VI
96. Explain the different types of astronomical terms
97. Explain the fundamental parameters by which total station works
98. What are the applications and advantages of total station
99. Explain the procedure of doing survey by total station
100. What are the errors in Total station

F
HS 210
LIFE SKILLS

SEMESTER: S3
COURSE: LIFE SKILLS
COURSE CODE: HS210
COURSE TYPE: COMMON
REGULATION: 2015
COURSE AREA/DOMAIN: HUMANITIES CONTACT HOURS: 4 hours/Week.
(IF ANY): NIL
SYLLABUS:
UNIT DETAILS HOURS
Communication Skill:
Need for Effective Communication, Levels of communication; Flow of
communication; Use of language in communication; Communication
networks; Significance of technical communication, Types of barriers;
Miscommunication; Noise; Overcoming measures, Listening as an
active skill; Types of Listeners; Listening for general content;
Listening to fill up information; Intensive
Listening; Listening for specific information; Developing effective
listening skills; Barriers to effective listening skills.
Technical Writing: Differences between technical and literary style,
Elements of style; Common Errors, Letter Writing: Formal, informal
and demi-official letters; business letters, Job Application: Cover
I letter, Differences between bio-data, CV and Resume, Report Writing: 20
Basics of Report Writing; Structure of a report; Types of reports.
Non-verbal Communication and Body Language: Forms of non-verbal
communication; Interpreting body-language cues; Kinesics;
Proxemics; Chronemics; Effective use of body language
Interview Skills: Types of Interviews; Ensuring success in job
interviews; Appropriate use of non-verbal communication, Group
Discussion: Differences between group discussion and debate;
Ensuring success in group discussions, Presentation Skills: Oral
presentation and public speaking skills; business presentations,
Technology-based Communication: Netiquettes: effective e-mail
messages; power-point presentation; enhancing editing skills using
computer software.
Critical Thinking & Problem Solving:
Need for Creativity in the 21st century, Imagination, Intuition,
Experience, Sources of Creativity, Lateral Thinking, Myths of
II creativity 9
Critical thinking Vs Creative thinking, Functions of Left Brain & Right
brain, Convergent & Divergent Thinking, Critical reading & Multiple
Intelligence.
Department of Civil Engineering, RSET F.2

UNIT DETAILS HOURS

Steps in problem solving, Problem Solving Techniques, Problem
Solving through Six Thinking Hats, Mind Mapping, Forced
Connections.
Problem Solving strategies, Analytical Thinking and quantitative
reasoning expressed in written form, Numeric, symbolic, and graphic
reasoning, Solving application problems.
Teamwork:
Introduction to Groups and Teams, Team Composition, Managing
Team Performance, Importance of Group, Stages of Group, Group
Cycle, Group thinking, getting acquainted, Clarifying expectations.
III Group Problem Solving, Achieving Group Consensus. 7
Group Dynamics techniques, Group vs Team, Team Dynamics, Teams
for enhancing productivity, Building & Managing Successful Virtual
Teams. Managing Team Performance & Managing Conflict in Teams.
Working Together in Teams, Team Decision-Making, Team Culture &
Power, Team Leader Development.
Ethics, Moral & Professional Values:
Morals, Values and Ethics, Integrity, Work Ethic, Service Learning,
Civic Virtue, Respect for Others, Living Peacefully.
Caring, Sharing, Honesty, Courage, Valuing Time, Cooperation,
Commitment, Empathy, Self-Confidence, Character Spirituality,
Senses of 'Engineering Ethics’, variety of moral issued, Types of
inquiry, moral dilemmas, moral autonomy, Kohlberg's theory,
Gilligan's theory, Consensus and controversy, Models of Professional
Roles, Theories about right action, Self-interest, customs and religion,
IV application of ethical theories. 11
Engineering as experimentation, engineers as responsible
experimenters, Codes of ethics, Balanced outlook on.
The challenger case study, Multinational corporations,
Environmental ethics, computer ethics
Weapons development, engineers as managers, consulting engineers,
engineers as expert witnesses and advisors, moral leadership, sample
code of Ethics like ASME, ASCE, IEEE, Institution of Engineers(India),
Indian Institute of Materials Management, Institution of electronics
and telecommunication engineers(IETE), India, etc.
Leadership Skills:
Introduction, a framework for considering leadership,
entrepreneurial and moral leadership, vision, people selection and
development, cultural dimensions of leadership, style, followers,
crises.
V Growing as a leader, turnaround leadership, gaining control, trust, 7
managing diverse stakeholders, crisis management
Implications of national culture and multicultural leadership
Types of Leadership, Leadership Traits.
Leadership Styles, VUCA Leadership, DART Leadership,
Transactional vs Transformational Leaders, Leadership Grid,
Effective Leaders, making of a Leader, Formulate Leadership
TOTAL HOURS 54

R1 Life Skills for Engineers. Compiled by ICT Academy of Kerala. Chennai: McGraw
Hill Education, 2016. Print.
R2 de Bono, Edward. Six Thinking Hats. London: Penguin Books, 2000. Print.
R3 Barun K. Mitra; (2011), “Personality Development & Soft Skills”, First Edition;
Oxford
R4 Publishers.
R5 Kalyana; (2015) “Soft Skill for Managers”; First Edition; Wiley Publishing Ltd.
R6 Larry James (2016); “The First Book of Life Skills”; First Edition; Embassy
Books.
R7 ShaliniVerma (2014); “Development of Life Skills and Professional Practice”;
First Edition; Sultan Chand (G/L) & Company
Basic communication The ability to read, listen to, understand
skills in English and write in the English language.
COURSE OBJECTIVES:
1 To develop communication competence in prospective engineers.
2 To enable them to convey thoughts and ideas with clarity and focus.
3 To develop report writing skills.
4 To equip them to face interview & Group Discussion.
5 To inculcate critical thinking process.
6 To prepare them on problem solving skills.
7 To provide symbolic, verbal, and graphical interpretations of statements in a
problem description.
8 To understand team dynamics & effectiveness.
9 To create an awareness on Engineering Ethics and Human Values.
10 To instil Moral and Social Values, Loyalty and also to learn to appreciate the
rights of others.
11 To learn leadership qualities and practice them.
COURSE OUTCOMES:
Sl
No.
The students will be able to remember theories pertaining to communication,
1 creativity, problem solving, moral development and leadership.
H L

Sl
No.
The students will be able to comprehend the importance of leadership qualities,
2 code of ethics, team dynamics and of communication.
H M L
The students will be able to apply skills pertaining to presentation, group
discussion, technical writing, problem solving, creative and critical thinking and
3
leadership in everyday life.
H L
The students will be able to analyze non-verbal communication cues and
4 leadership roles
M H M H
The students will be able to evaluate different perspectives that arise due to an
5 ethical dilemma
H

Comprehension and practice of letter writing, report writing
PO10 HIGH and presentations enable students to communicate
effectively.
CO1
Theories pertaining to communication, creativity, problem
PO12 LOW solving, moral development and leadership facilitate
lifelong learning.
Critical thinking and reading techniques help students
PO2 HIGH identify reliable literature and analyze engineering
problems with clarity
CO2 Brainstorming techniques and lateral thinking helps design
PO3 MEDIUM
innovative solutions to engineering problems
In investigating complex problems, critical reading patterns
PO4 LOW
helps reach better conclusions.
Understanding the basics of becoming a team player helps
PO9 HIGH
them function effectively in groups and teams
CO3 In applying engineering knowledge, awareness of the role of
PO11 LOW a leader, manager and team member helps students function
in a context in an appropriate manner.
Awareness of engineering ethics leads to consideration of
PO3 MEDIUM environmental issues etc. while making engineering
CO4 solutions.
Awareness of engineering ethics ensures consideration of
PO6 HIGH
societal, health, safety issues as an engineer

Ethics of engineering include sustainable engineering ethics
PO7 MEDIUM making students aware of need for sustainable
development.
Professional ethics, dilemmas and case studies help students
PO8 HIGH apply principles and make informed decisions based on
norms of engineering
The principles of leadership help them become dynamic and
CO5 PO9 HIGH
tactful leaders solving problems of teams.

1 Characteristics of languages - Introduction to Lecture
Verbal Communication
2 Cultural Relativism of body language Presentation/ Lecture

Sl No DESCRIPTION
1 The Seven Habits of Highly Effective People - Stephen R. Covey
2 Five W’s in Problem Solving
3 6-3-5 Brainwriting

Sl No DESCRIPTION
1 http://www.yourarticlelibrary.com/management/communication/top-5-
types-of-communication-network-with-diagram/60302/
2 http://www.debonogroup.com/six_thinking_hats.php
3 http://www.folj.com/lateral/
LCD/SMART
BOARDS
ASSIGNMENTS
CERTIFICATIONS
ADD-ON
OTHERS
COURSES

OTHERS
EVALUATION SCHEME
 Internal Evaluation (conducted by college) : 100 marks

 External Evaluation (conducted by university): 50 marks – 2 hours
INTERNAL EVALUATION
1. Group Discussion – 40 marks (to be completed by 30th working day of the

semester)
2. Presentation – 30 marks (to be completed before 60th working day of the
semester)
3. Written assignment – 30 marks (to be completed before end of semester)
Dr. Sonia Paul Dr. Antony Varghese
HoD, DBSH

S
CE 231
CIVIL ENGINEERING DRAFTING
LAB

COURSE: CIVIL ENGINEERING DRAFTING SEMESTER: S3
LAB L-T-P-CREDITS: 0-0-3-1
COURSE CODE: CE231
COURSE TYPE: CORE
REGULATION: 2016
ENGINEERING
LIST OF EXERCISES: (at least 10 exercises / plates are mandatory )

Sl. No. DETAILS
1. Panelled Doors
2. Glazed Windows and Ventilators in wood
3. Steel windows
4. Roof truss in steel sections
5. Reinforced concrete staircase
6. Residential buildings with flat roof
7. Residential buildings with tiled roof
8. Preparation of site plan and service plans as per building rules
Building Services (for single and two storied buildings only). Septic tanks
9.
and soak pit (detailed drawing)
10. Two storied and multi storied buildings
11. Public buildings like office, dispensary, post office, bank etc.
12. Industrial buildings with trusses
T1 National Building Code of India.
T2 Kerala Municipal Building Rules.
T3 Dr. Balagopal T.S. Prabhu, Building Drawing and Detailing, Spades Publishers,
Calicut
T4 AutoCAD Essentials, Autodesk official Press, John Wiley & Sons, USA
R1 Shah, M.G., Kale, C. M. and Patki, S.Y. Building Drawing With An Integrated
Approach to Built Environment, Tata McGraw Hill Publishing Company Limited,
New Delhi
Department of Civil Engineering, RSET S.2

BE110 ENGINEERING Concept of plan, section, elevation and S2
GRAPHICS projections and basic knowledge in
AutoCAD
COURSE OBJECTIVES:
1 To introduce the fundamentals of Civil Engineering drawing.
2 To understand the principles of planning
3 To learn drafting of buildings.
4 To impart knowledge on drafting software such as AutoCAD
COURSE OUTCOMES:
Sl
No.
The students will be able to illustrate reinforced concrete staircase after
1 calculating the space available
M L
The students will be able to illustrate the partial elevations of Steel truss and
2 the connections involved
M
The students will be able to develop the plan, section and elevation of single
3 storied and double storied buildings from given line sketches
H M
The students will be able to plan and develop line sketches and working
drawings of single storied RCC residential buildings as per area and functional
4
requirements
H H H H
The students will be able to develop site plan of a given building using Kerala
5 Building Rules
H M L
The students will be able to make use of Auto CAD software for preparation of
6 plan, elevation and section of a building
H M L

Students will be able to apply knowledge of mathematics
CO1 PO1 MEDIUM and engineering fundamentals to Prepare the drawing of
reinforced concrete staircase after calculating the space
available

Students will formulate and analyse complex problems
PO2 LOW related to partial elevations of Steel truss and the
connections involved
Roof trusses are an eminent component of any modern day
CO2 PO1 MEDIUM house and hence are the knowledge about how to select
one.
The plan, section and elevation of a house are the skeleton
PO1 HIGH of civil engineering design and hence the knowledge is
CO3 paramount for a Civil Engineer.
PO2 MEDIUM related to plan, section and elevation of single storied and
double storied buildings from given line sketches
Students will be able to apply knowledge of basic
fundamentals while designing any house is the conflicting
PO1 HIGH ideas of space allocation and practicing an optimum
between aesthetic requirements and functional
requirements
related to Plan and develop line sketches and working
PO2 HIGH
drawings of single storied RCC residential buildings as per
CO4 area and functional requirements.
Students will design solutions for complex engineering
problems and develop line sketches and working drawings
PO3 HIGH
of single storied RCC residential buildings as per area and
functional requirements.
Students will develop the ability to engage in independent
and life-long learning in the broadest context of
PO12 HIGH technological change by drawing single storied RCC
residential buildings as per area and functional
requirements.
Students will be able to apply knowledge of basic
PO1 HIGH fundamentals to design a good house, abiding by the laws
imposed by the authorities.
Students will formulate and analyse complex problems to
CO5 PO2 MEDIUM develop site plan of a given building using Kerala Building
Rules
Students will design solutions for complex engineering
PO3 LOW problems and develop site plan of a given building using
Kerala Building Rules
The idea of designing is made simpler and faster by software
PO1 HIGH like AutoCAD and hence the knowledge of working on the
software is also of high importance.
CO6 Students will formulate and analyse complex problems for
PO2 MEDIUM
preparation of plan, elevation and section of a building
Students will make use of model tool Auto CAD
PO5 LOW software for preparation of plan, elevation and section of a
building


1 King Post truss and Queen post truss Lectures
2 Sanitary fittings and plumbing Lectures

Sl No DESCRIPTION
1 NIL

Sl No DESCRIPTION
1 http://nptel.ac.in/courses/112103019/
LCD/SMART
BOARDS
ASSIGNMENTS
CERTIFICATIONS
ADD-ON
OTHERS
COURSES
OTHERS
Nimisha Reji Dr. Aysha Zeneeb Majeed

COURSE PLAN
DAY TOPICS PLANNED

DAY 1 Introduction to Civil Engineering drawing
DAY 2 Panelled Doors
DAY 3 Glazed window
DAY 4 Roof truss in steel sections
DAY 5 Reinforced concrete staircase
DAY 6 Residential building with flat roof
DAY 7 Introduction to Auto CAD, Site plan
DAY 8 Residential building with tiled roof
DAY 9 Building services (Septic tank and soak pit details)
DAY 10 Two-storied building
DAY 11 Public Building
DAY 12 Repeat class
DAY 13 Repeat class
DAY 14 Lab Exam
DAY 15 Lab Exam
LAB CYCLE
CYCLE 1: (MANUAL DRAFTING)
1. SYMBOLS AND PROJECTIONS

2. PANELLED DOOR
3. GLAZED WINDOW
4. STEEL TRUSS
5. REINFORCED STAIRCASE
6. A SIMPLE HOUSE (PLAN, SECTION, ELEVATION)
CYCLE 2: (AutoCAD)
1. SITE PLAN
2. SEPTIC TANK AND SOAK PIT
3. HOUSE WITH SLOPING ROOF
4. PUBLIC BUILDING: PRIMARY HEALTH CENTRE
5. TWO-STOREY BUILDING

OPEN QUESTIONS
1. What is meant by first angle projection?

2. What are the sizes of A0, A1, A2, A3 and A4 sheets?
3. When is a line shown as dotted?
4. What is the hatching shown for brick and concrete?
5. What is meant by section line?
6. What is meant by upright, style and horn for panelled door?
7. What are the minimum setbacks to be given for a small plot?
8. What is the minimum distance between a well and septic tank?
9. What is the minimum height of a floor of a public building?
10. What are the rules for taking a section of a building?
11. What are the different types of stairs?
12. How are ventilators designated?
13. Explain about the different types of trusses?
14. What are the functions of purlins and cleats in truss work?
15. In what orientation should the windows be provided in a building?
16. What is meant by an isometric view?
17. What are the basic functions in AutoCAD?
18. What is the minimum rise and tread of a stir in an office building?
19. What is the function of providing a lintel?
20. Explain the components of the foundation of a building?

ADVANCED QUESTIONS
1. You are required to design a cinema theatre to be located in an important

commercial area in Kozhikode city. A plot of land measuring 120m x 140m
abutting a 12m wide road on the Western side has been selected for the
project. The road on the longer side of the plot. There is a gradual ground slope
of 1/20 from east to west. Applicable building rules, requirements and
approximate areas are given below:
Building Rules:
The minimum setback in front= 12m
The minimum setback in rear= 3m
The minimum setback on each side= 6m
Requirements:
Seating area of 1000 persons- 600 sq.m
Lounges with adequate toilet facilities-100 sq.m
Snack bar-20 sq.m
Ticket booths for regular and advanced booking-1 for each class
Projection room-30 sq.m
Rewinding room- 30sq.m
Manager’s office with toilet- 20 sq.m
Accountant’s office-15 sq.m
Car parking space for 30 cars
Two-wheeler parking for 50 vehicles
Cycle stand for 100 vehicles
Drawings required:
Plan
Section
Elevation
2. You are invited to take part in the competition for designing a fine arts college in
your locality. The site will be in the proximity of an existing museum and with
good number of trees. The site has a 12m road on the East side. There is no
restriction for the site dimensions. However the total area on the ground floor
including landscaping and parking shall not exceed 3 acres. The following are the
main requirements:
Entrance lobby & office-30 sq.m
Principal’s chamber with toilet-30 sq.m
Library including reading room-120 sq.m
Professor’s room with toilet- 5 Nos 12 sq.m each
Assistant professor’s room with common toilets- 10 Nos 12 sq.m each
Lecturer’s cabin with 6 Lectures- 8 sq.m each
Girl’s common toilet- 60 sq.m
Boy’s common toilet- 60 sq.m
Canteen- 80 sq.m

Workshops- 2 Nos of 100 sq.m each

General store-60 sq.m
Painting studio-100 sq.m
Commercial art studio-100 sq.m
Photography room with dark room- 50 sq.m
4 class rooms- 60 sq.m each
3. A Public Library:
The site for the purpose is a flat land. The land measures 70m (N-S) and 100m
(E-W) with a 10m wide road on one of the shorter sides facing East. The general
requirements are:
a. Reading hall to seat 100 users.
b. Stacking of books on ground floor near reading hall and on the mezzanine
overlooking the reading hall. Arrangement for atleast 50 shelves of 1 m x
2.1 m (height) x 0.45 m (depth) to be worked out.
c. Librarian’s room, Assistant Librarian’s room and office.
d. Indexing, Binding, and classifying section.
e. Xerox room, Microfilm, etc.
f. Issue and return counter.
g. Magazine and periodical section for 25 periodicals.
h. Entrance lobby and space for occasional book exhibition.
i. Toilets.
Assume suitable required data. Prepare the following drawings to explain the
design.
(i) Plans
(ii) Sections
(iii) Front elevation

T
CE 233
SURVEYING LAB

SEMESTER: S3
COURSE: SURVEYING LAB
COURSE CODE: CE233
COURSE TYPE: REGULAR
REGULATION: 2016
ENGINEERING
LIST OF EXERCISES:
Sl. No. DETAILS
1. Introduction to Conventional Surveying
2. Levelling (Dumpy Level)
3. Theodolite Surveying (Theodolite)
Total Station Survey (Total Station)
a) Heights and Distance
4.
b) Area Computation
c) Downloading
Study of Instruments
a) Automatic Level
5.
b) Digital Level
c) Handheld GPS
Prof. T.P.Kenetkar & Prof.S.V.Kulkarni - Surveying and Levelling , Pune Vidyarthi
T1
Griha Prakashan,2004
T2 N N Basak, Surveying and Levelling, Mc GrawHill Education
R1 R.Agor - A Text book of Surveying and Levelling, Khanna Publishers, 2005
C. Venkatramaiah, Textbook of Surveying, Universities Press (India) Private
R2
Limited 2011
James M Andersen, Edward M Mikhail, Surveying Theory and Practice, McGraw
R3
Hill Education
Dr. B.C.Punmia , Ashok Kumar Jain &Arun Kumar Jain - Surveying , Laxmi
R4
Publications (P)Ltd , 2005
R5 S.K.Duggal - Surveying Vol. I, Tata Mc Graw Hill Ltd ,Reprint 2015.
Department of Civil Engineering, RSET T.2

MATHEMATICS FUNDAMENTAL KNOWLEDGE OF SECONDARY
TRIGONOMETRY SCHOOL
LEVEL
COURSE OBJECTIVES:
1 To equip the students to undertake survey using tacheometer.
2 To equip the students to undertake survey using total station
3 To impart awareness on distomat and handheld GPS
COURSE OUTCOMES:
Sl
No.
The student shall be able to understand the concept of open traverse surveying
1 and apply the same on the fields.
M M L
The student shall be able to understand the concept of Levelling and apply it to
find elevations of different points in the field by Collimation Method or Rise and
2
Fall Method.
M M L
The student shall be able to determine the angles by Method of Reiteration using
3 Theodolite.
M M L
The student shall be able to determine the angles by Method of Repetition using
4 Theodolite.
M M L
The student shall be able to understand the meaning of slope distance, horizontal
distance and vertical height and its measurement using a Total Station
5
Instrument.
L M M L
The student shall be able to use resection or method of coordinate for the
6 measurement of area using a Total Station Instrument.
L M M L

The students shall use the basics of science and mathematics
PO1 MEDIUM
to find solution to the traverse problems.
CO1
The designed experiment teaches a student how to work in
PO9 MEDIUM
a team while playing their individual roles.

The student has to communicate on how the experiment had
PO10 LOW been conducted and write reports of the same which helps
him in his communication skills.
The students shall learn the basics of leveling and compute
PO1 MEDIUM the level differences using height of instrument method and
rise-fall method.
CO2 PO9 MEDIUM
The student shall learn the basics of theodolite surveying
PO1 MEDIUM and use method of reiteration to solve the experimental
problem.
C03 PO9 MEDIUM
The student shall learn the basics of theodolite surveying
PO1 LOW and use method of repetition to solve the experimental
problem.
CO4 PO9 MEDIUM
The student shall learn the basics of total station and
PO1 LOW
determine the distances between two points
Usage of modern tools in surveying for real field problem to
PO5 MEDIUM
calculate the distances
CO5 The designed experiment teaches a student how to work in
PO9 MEDIUM
The student shall understand the basics and choose the
PO1 LOW
method to calculate the area of a field.
CO6
Usage of modern tools in surveying for real field problem to
PO5 LOW
calculate the area of a field

PO9 MEDIUM

1

Sl No DESCRIPTION
1

Sl No DESCRIPTION
1 www.nptel.ac.in
LCD/SMART
BOARDS
ASSIGNMENTS
CERTIFICATIONS
ADD-ON
OTHERS
COURSES
OTHERS
Jibin Joseph Dr. Aysha Zeneeb Majeed

COURSE PLAN
DAY TOPICS PLANNED

DAY 1 Introduction to Conventional Surveying
DAY 2 Open Traverse Surveying
DAY 3 Reduction of Levels by Height of Instrument Method
DAY 4 Reduction of Levels by Rise and Fall Method
DAY 5 Study of Theodolite
DAY 6 Measurement of Horizontal Angle by Method of Repetition
DAY 7 Determination of Horizontal Distances by Reiteration Method
DAY 8 Height of Accessible Post - Vertical Angle
DAY 9 Height of Inaccessible Post - Vertical Angle
Determination of Elevation Difference between Two Points by
DAY 10
Theodolite
DAY 11 Study of Total Station
Determination of Vertical Height of an Inaccessible Tree by Total
DAY 12
Station (Remote Height)
Determination of Heights and Distances of Given Points by Total
DAY 13
Station (Tie Distance)
DAY 14 Total Station - Determination of Area - Method of Resection
DAY 15 Total Station - Determination of Area - Method of Coordinates
DAY 16 Total Station - Downloading/Exporting Data to Computer
DAY 17 Exam

OPEN QUESTIONS
Basics:
1. What is Surveying?
2. What is Leveling?
3. What are the objective and uses of Surveying?
4. Explain the Methods of Surveying
a. Triangulation
b. Traversing
5. Explain:
a. Topographic Map
b. Cadastral Map
c. Engineering Map
d. Military Map
e. Contour Map
f. Geological Map
g. Archeological Map
6. What is the general principle of Surveying?
Chain Surveying:
7. What is Chaining?
8. What are the instruments used in Chain Surveying?
9. How many links are in 30m Metric Chain? Length of each link?
10. What is Reciprocal Ranging?
11. What are Corrections?
12. How many ranging rods required for
a. Direct Ranging
b. Indirect or Reciprocal Ranging
13. Principle of Chain Surveying?
14. What is well-conditioned triangle?
15. What is Reconnaissance Survey?
16. What is Index Sketch?
17. How to set Perpendicular Offsets? (900)
18. What is Field Book?
Compass Surveying:
19. What is the principle of Compass Surveying?

20. Explain:
a. True Meridian
b. Magnetic Meridian
c. Arbitrary Meridian
d. Magnetic Bearing
i. Whole Circle Bearing (WCB)
ii. Quadrantal Bearing (QB)

iii. Reduced Bearing (RB)

e. Fore Bearing
f. Back Bearing
g. Magnetic Declination
h. Dip of the magnetic needle
i. Local Attraction
21. What is traversing?
a. Close Traverse?
b. Open Traverse?
22. Check on Closed Traverse
a. Sum of exterior angles?
b. Sum of interior angles?
23. Check on Open Traverse
24. How to adjust Closing Error?
Leveling:
25. What are the uses of Leveling

26. Explain the term Datum Surface or Line
27. What is Reduced Level?
28. Explain Line of Collimation?
29. Explain Bench-marks (BM)
a. GTS Bench-marks
b. Permanent Bench-marks
c. Arbitrary Bench-marks
d. Temporary Bench-marks
30. Backsight Reading (BS)
31. Foresight Reading (FS)
32. Intermediate sight Reading (IS)
33. Change Point?
34. Instruments used in Leveling?
35. Types of Leveling?
a. Simple Leveling
b. Differential Leveling
c. Fly Leveling?
d. Profile Leveling?
e. Check Leveling?
36. Explain the need of Reciprocal Leveling?
37. What are the Methods of Calculation of Reduced Level
a. Height of Instrumentation method
b. Rise-and-Fall method
38. Explain Arithmetical Check?

ADVANCED QUESTIONS
Objective Questions
1. In chain surveying tie lines are primarily provided

a. to avoid long offsets from chain lines
b. to take offsets for detail survey
c. to check the accuracy of the survey
d. to increase the number of chain lines.
2. In chain surveying field work is limited to
a. linear measurements only
b. both linear and angular measurements
c. all the above.
d. angular measurements only
3. The real image of an object formed by the objective, must lie
a. in the plane of cross hairs
b. at the centre of the telescope
c. at the optical centre of the eye-piece
d. anywhere inside the telescope.
4. The intercept of a staff
a. decreases if the staff is tilted away from normal
b. is maximum if the staff is held truly normal to the line of sight.
c. is minimum if the staff is held truly normal to the line of sight.
d. increases if the staff is tilted towards normal.
5. Closed contours of decreasing values towards their centre, represent
a. a river bed.
b. a depression
c. a hill
d. a saddle or pass
6. An imaginary line joining the points of equal elevation on the surface of the
earth, represents
a. contour line
b. contour surface
c. contour gradient
d. level line
7. If R is the radius of the main curve, θ the angle of deflection, S the shift and L the
length of the transition curve, then, total tangent length of the curve, is
a. (R + S) tan θ/2 + L/2
b. (R - S) tan θ/2 + L/2
c. (R + S) tan θ/2 - L/2
d. (R - S) tan θ/2 - L/2
8. The accuracy of measurement in chain surveying, does not depend upon
a. general layout of the chain lines.
b. importance of the features
c. length of the offset
d. scale of the plotting

9. Pick up the correct statement from the following :

a. standing on the tripod is the levelling head or trib arch
b. the levelling screws are used to tilt the instrument so that its rotation axis
is truly vertical
c. the tangent screw enables to give small movement under conditions of
smooth and positive control
d. all of these
10. An ideal vertical curve to join two gradients, is
a. elliptical
b. hyperbolic
c. parabolic
d. circular
11. One of the tacheometric constants is additive, the other constant, is
a. subtractive constant
b. multiplying constant
c. dividing constant
d. indicative constant.
12. Two concave lenses of 60 cm focal length are cemented on either side of a convex
lens of 15 cm focal length. The focal length of the combination is
a. 20cm
b. 40cm
c. 10cm
d. 30cm
13. Hydrographic surveys deal with the mapping of
a. canal system
b. heavenly bodies
c. large water bodies
d. mountaineous region
14. The radius of curvature of the arc of the bubble tube is generally kept
a. 10m
b. 25m
c. 50m
d. 100m
15. The limiting length of an offset does not depend upon
a. accuracy of the work
b. indefinite features to be surveyed.
c. scale of plotting
d. method of setting out perpendiculars
16. For true difference in elevations between two points A and B, the level must be
set up
a. at the exact mid point of A and B
b. near the point A
c. near the point B.
d. at any point between A and B
17. The difference of level between a point below the plane of sight and one above, is
the sum of two staff readings and an error would be produced equal to

a. the distance between the zero of gradient and the foot of the staff
b. thrice the distance between the zero of graduation and the foot of the
staff
c. twice the distance between the zero of graduation and the foot of the staff
d. none of the above.
18. Surveys which are carried out to depict mountains, rivers, water bodies, wooded
areas and other cultural details, are known as
a. topographical surveys
b. city surveys
c. cadastral surveys
d. guide map surveys

S3 Course Handout

Uploaded by

Copyright:

Available Formats

S3 Course Handout

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

S3 Course Handout

Uploaded by

Copyright:

Available Formats

RAJAGIRI SCHOOL OF ENGINEERING &

DEPARTMENT OF CIVIL ENGINEERING

B TECH IN CIVIL ENGINEERING

RAJAGIRI SCHOOL OF ENGINEERING AND TECHNOLOGY

To impart quality education and mould technically sound, ethically responsible

Program Educational Objectives (PEOs)

PEO 3: Commitment to society: Graduates shall display a high sense of social

Program Specific Outcomes (PSOs)

Civil Engineering Graduates will be able to:

Program Outcomes (POs)

Engineering Graduates will be able to:

Department of Civil Engineering, RSET 1

PO 1. Engineering knowledge: Apply the knowledge of mathematics, science, engineering

PO 2. Problem analysis: Identify, formulate, review research literature, and analyse

PO 3. Design/development of solutions: Design solutions for complex engineering

PO 4. Conduct investigations of complex problems: Use research-based knowledge and

PO 7. Environment and sustainability: Understand the impact of the professional

PO 8. Ethics: Apply ethical principles and commit to professional ethics and

PO 9. Individual and team work: Function effectively as an individual, and as a member

PO 10. Communication: Communicate effectively on complex engineering activities with

PO 11. Project management and finance: Demonstrate knowledge and understanding of

Department of Civil Engineering, RSET 2

SL NO: CONTENTS PAGE

Department of Civil Engineering, RSET 3

DATE SUB. CODE SUBJECT

3.9.2018 CE201 Mechanics of Solids

Department of Civil Engineering, RSET 4

SCHEME: B.TECH 3RD SEMESTER

MA201 Linear Algebra & Complex Analysis 3-1-0 4 A

Total Credits = 24 Hours: 29 Cumulative Credits= 71

Department of Civil Engineering, RSET 5

COURSE INFORMATION SHEET

PROGRAMME: CE DEGREE: BTECH

Department of Civil Engineering, RSET A.2

UNIT DETAILS HOURS

Department of Civil Engineering, RSET A.3

JUSTIFICATION FOR CO-PO MAPPING:

GAPS IN THE SYLLABUS - TO MEET INDUSTRY/PROFESSION REQUIREMENTS:

Department of Civil Engineering, RSET A.4

3 Importance of matrix application in different Reading

TOPICS BEYOND SYLLABUS/ADVANCED TOPICS/DESIGN:

WEB SOURCE REFERENCES:

Department of Civil Engineering, RSET A.5

HOUR MODULE TOPICS PLANNED

Department of Civil Engineering, RSET A.6

HOUR 45 Homogeneous linear systems

Department of Civil Engineering, RSET A.7

1. State True or False and Justify

4. Let for . Compute the partial derivatives

5. Find an analytic function for the following expressions.

Department of Civil Engineering, RSET A.8

conjugate. Do the same for

Department of Civil Engineering, RSET A.9

a. All vectors in with

b. All vectors in with

25. Solve the linear system by its augmented matrix

dimension and find the basis.( denote components)

a. All vectors in such that 4 + =k

b. All vectors in such that 3 -2 + = 0, 4 + =0