Eim Grade 11 Questioner

ELECTRICAL INSTALLATION AND MAINTENANCE
GRADE 11
NAME: DATE:
SCHOOL: SCORE:
TEST 1
Multiple Choice: Encircle the letter of the correct answer.
1. An instrument used to measure the amount of electrical current intensity in a circuit.
a. megger c. ammeter
b. testlight d. micrometer
2. Is an instrument used to measure the electrical pressure or voltage of a circuit.
a. voltmeter c. ammeter
b. wire gauge d. all of the above
3. It is used to measure the current flowing in a conductor.
a. micrometer c. megger
b. clamp ammeter d. none of the above
4. It is used to measure the voltage, resistance, and current of a circuit.
a. volt-ohmmeter c. clamp ammeter
b. voltmeter d. testlight
5. Is a pocket-sized tool used to test the presence of current in a line wire or circuit.
a .testlight c. micrometer
b. ammeter d. voltmeter
6. Used to measure the diameter of wires/conductors in circular mils.
a. micrometer c. wire gauge
b. ruler d. pull-push rule
7. It is used in determining the sized of wires/conductors.
a. micrometer c. wire gauge
b. voltmeter d. ammeter
8. These are tools are made steel hardened and tempered at the tip used to loosen or tighten screws
with slotted heads.
a. screwdrivers c. pliers
b. hammers d. all of the above
9. The blade tip is wedge-shaped and resembles a negative sign.
a. standard/flat screwdriver c. stubby screwdriver
b. hammer d. none of the above
10. This is used to drive screws with cross slot heads.
a. allen wrench c. flat screwdriver
b. Philips screwdriver d. hammer
11. This comes in either standard or Philips screwdriver with short shank or blade and a shorted handle
used to turn screws in tight spaces where standard screwdriver cannot.
a. stubby screwdriver c. screwdriver
b. hammers d. mallet
12. Its function is to drive screws with hexagonal slot heads.
a. ballpeen hammer c. allen wrench
b. claw hammer d. none of the above
13. These are tools used in driving or pounding and pulling out nails.
a. hammer c. micrometer
b. testlight d. all of the above
14. The following are the types of hammers except.
a. claw hammer c. mallet
b. ballpeen hammer d. crank hammer
15. Are tools are made from metal with insulators in the handle and are used for cutting, twisting,
bending, and gripping wires and cables.
a. screwdriver c. hammers
b. cutter d. pliers
TEST 2
Objective type: Write your answers on the space provided before the number.
_________16. This is used for gripping, holding, and cutting electrical wires and cables and even small
nails.
_________17. This type of pliers is used for cutting fine, medium, and big wires and cables.
_________18. Is used for cutting and holding fine wires.
_________19. A tool used for removing insulation of medium-sized wires ranging from gauge no.10 to
gauge no. 16.
_________20. This used by lineman to remove insulation of wire and cables in low and high voltage
transmission lines.
_________21. Used in making holes on metal sheets and concrete walls.
_________22. A tool is used to cut metal conduit and armored cable.
_________23. A device that act as convenient source of electrical energy for current consuming
apppliences.
_________24. Device inserted to a convenience outlet to conduct electric current.
_________25. A device that hold and protect the lamp.
_________26. A device that connects and disconnect the flow of electric current in a circuit.
_________27. A circuit protective device that automatically blows and cuts the current when overload
or short circuit happens.
_________28. An octagonal shaped electrical material where the connections or joints of wire are being
done.
_________29. A rectangular shaped metallic or plastic material in which flush type convenience outlet
and switch are attached.
_________30. A duplex stranded wire used for temporary wiring installation and commonly used in
extension cord assembly.
TEST 3
Matching type: Match column A to column B write only the letter of the correct answer.
Column A Column B
31. It is also called instant start ballast. A. T12’s
32. He invented the first practical incandescent lamp. B. magnetic ballast
33. Oldest type of fluorescent tubes. C. electronic ballast
34. Smallest type of fluorescent tubes and can last up to d. T5’s
90,000 hours.
35. Are 1 inch in diameter fluorescent tubes and they e. T8’s
Are the most prevalent of all fluorescent tubes. F. Thomas Edison
36. Older ballast technology. G. Benjamin Franklin
37. A device that produces light by the flow of electric h. fluorescent tubes
Current. I. neon lamps
38. A gas discharge tubes that uses fluorescence j. compact fluorescent lamp
To produce visible light.
39. A gas discharge lamp that contains gas at low k. metal halide
Pressure.
40. A modern type of light bulb that works like a
Fluorescent lamp.
TEST 4
Direction: Draw the electrical symbols of the following description;
41. switch
42. circuit breaker
43. fuse
44. ammeter
45. voltmeter
46. wattmeter
47. ground
48. power panel board
49. lighting arrester
50. incandescent lamp

Eim Grade 11 Questioner

Uploaded by

Copyright:

Available Formats

Eim Grade 11 Questioner

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Eim Grade 11 Questioner

Uploaded by

Copyright:

Available Formats

ELECTRICAL INSTALLATION AND MAINTENANCE

You might also like