Scribd
Upload
2K views4 pages

Davit Calc

The document provides calculations to determine if the design of a manway davit and its components are adequate to support the loads. It calculates stresses on the davit arm from applied forces, compares them to allowable stresses, and determines the design is adequate. It also calculates required sizes for an eye bolt and fillet welds and confirms the specified sizes are adequate based on applied loads. In summary, the calculations show the manway davit design and specified component sizes can withstand the expected operating loads.

Uploaded by

rustamriyadi
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
2K views4 pages

Davit Calc

The document provides calculations to determine if the design of a manway davit and its components are adequate to support the loads. It calculates stresses on the davit arm from applied forces, compares them to allowable stresses, and determines the design is adequate. It also calculates required sizes for an eye bolt and fillet welds and confirms the specified sizes are adequate based on applied loads. In summary, the calculations show the manway davit design and specified component sizes can withstand the expected operating loads.

Uploaded by

rustamriyadi
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
You are on page 1/ 4

MANWAY DAVIT CALCULATION

(Ref. : Pressure Vessels Design Manual, Dennis R. Moss, 1989)

Job No. : JN 546-C-TSE-01 Revision : AB


Customer : CLOUGH INTERNATIONAL Date : 18/8/2005
Vessel Description : TEST SEPARATOR Prepare By : ASA

A Design Data
Weight of Blind Flange 24"NB 1500 # (incl. 100% misc. weights) w1 : 3,950 Lbs
Weight of Davit Arm w2 : 200 Lbs
Vertical Impact Factor Cv : 1.50
Horizontal Impact Factor Ch : 0.50
Size of Fillet Weld tc : 0.375 Inch
Allowable Stress of Fillet Weld f : 9,600 Psi

B Properties of Davit Arm


Material of Pipe Davit Arm : SA-106 Gr. B
Yield Stress of Davit Arm Material Ys : 35,000 Psi
Outside Diameter of Pipe Davit Arm OD : 5.563 Inch
Outside Radius of Pipe Davit Arm r : 2.78 Inch
Wall Thickness of Pipe Davit Arm tp : 0.625 Inch
Cross Sectional Area Of Pipe Davit Arm Ap : 9.696 Inch2
Moment Inertia of Pipe Davit Arm Ip : 29.972 Inch4
Section Modulus of Pipe Davit Arm Zp : 10.776 Inch3
Radius Gyration of Pipe Davit Arm rg : 1.760 Inch

C Properties of Eye Bolt


Material of Eye Bolt : SA-36
Allowable Stress of Eye Bolt Material Sb : 16,534 Psi
Diameter of Eye Bolt d : 1.181 Inch

L1 : 29.252 Inch
L2 : 24.567 Inch
L3 : 18.898 Inch
L4 : 25.945 Inch
R : 11.811 Inch
D Stress Coefficients
a = tp * R / r
2

= 0.625 x 11.811 / 2.782^2 a = 0.954


b = 6 / (5 + 6a2)
= 6 / (5 + 6 * 0.954^2) b = 0.573
K = 1 - [9 / (10 + 12a2)]
= 1 - (9 / (10 + 12 * 0.954^2)) K = 0.570

E Davit Arm Calculation


1. Load applied on davit arm
At vertical direction
fv = Cv * W1 = 1.5 x 3950 fv = 5925.000 Lbs
At horizontal direction
fh = Ch * W1 = 0.5 x 3950 fh = 1975.000 Lbs
2. Bending moment applied on davit arm at top guide or support
M1 = fv * L1 + 0.5 * W2 * L1 + fh * L2
= 5925 x 29.252 + 0.5 x 200 x 29.252 + 1975 x 24.567
M1 = 224763.125 Lbs.Inch
3. Axial load applied on davit arm
P = fv + W2 = 5925 + 200 P = 6125.000 Lbs
4. Slenderness ratio
Sr = 2.1 * L2 / rg = 2.1 x 24.567 / 1.7598 Sr = 29.317
5. Allowable axial stress of pipe davit arm
Fa = Stress value (AISC table with Sr) Fa = 20010.000 Psi
6. Allowable bending stress of pipe davit arm
Fb = 0.67 * Ys = 0.67 x 35000 Fb = 23450.000 Psi
7. Axial stress of pipe davit arm
fa = P / A p = 6125 / 9.696 fa = 631.719 Psi
8. Maximum bending moment in curved davit arm
M2 = M1 * (L2 - R) / L2
= 224763.125 x (24.567 - 11.811) / 24.567 M2 = 116704.458 Lbs.Inch
9. Bending stress on pipe davit arm
At M1
fb1 = M1 / Zp = 224763.125 / 10.7756 fb1 = 20858.477 Psi
At M2
fb2 = [M2 * r / Ip] * [2 / {3K * sqrt(3b)}]
= [116704.458 x 2.782 / 29.972] x [2 / {3 * 0.57 x sqrt. (3 * 0.573)}]
fb2 = 9659.293 Psi
10. Combined stress
At M1 = [fa / Fa] + [fb1 / Fb]
= [631.719 / 20010] + [20858.477 / 23450] = 0.921 Psi
At M2 = [fa / Fa] + [fb2 / Fb]
= [631.719 / 20010] + [9659.293 / 23450] = 0.443 Psi
11. Judgement
a. Since combined stress value at M1 less than 1.0 ADEQUATE
b. Since combined stress value at M2 less than 1.0 ADEQUATE

F Eye Bolt Calculation


1. Area available of eye bolt
Arb = p / 4 d2 = (22/7) / 4 1.181^2 Arb = 1.096 Inch2
2. Minimum area required of eye bolt
Ar1 = P / Sb = 6125 / 16534 Ar1 = 0.370 Inch2
3. Judgement
Since Arb more than Ar1 ADEQUATE
4. Length of fillet weld on eye bolt
Lw = 2 * p * d = 2 x (22/7) x 1.1811 Lw = 7.424 Inch
5. Minimum required fillet weld leg size
tc2 = P / (Lw * f) = 6125 / (7.424 x 9600) tc2 = 0.086 Inch
6. Judgement
Since tc2 less than tc ADEQUATE

G Welding Size on Plate and Pipe


1. Section modulus of weld lines
Sw = L32 / 3 = 18.898^2 / 3 Sw = 119.045 Inch2
2. Bending moment
Mb = P * L4 = 6125 x 25.945 Mb = 158913.125 Lbs.Inch
3. Bending force applied on fillet weld
Wb = Mb / Sw = 158913.125 / 119.045 Wb = 1334.902 Lbs/Inch
4. Average vertical shear force applied on fillet weld
Ws = P / 2 L3 = 6125 / 2 x 18.898 Ws = 162.054 Lbs/Inch
5. Resultante force applied on fillet weld
Rw = Sqrt (Wb2 + Ws2)
= Sqrt (1334.902^2 + 162.054^2) Rw = 1344.702 Lbs/Inch
6. Minimum required fillet weld leg size
tc1 = Rw / f = 1344.702 / 9600 tc1 = 0.140 Inch
7. Judgement
Since tc1 less than tc ADEQUATE
ADEQUATE
ADEQUATE

743 29.252
624 24.567
480 18.898
659 25.945
300 11.811

You might also like