TE30 Electricity Meter Tester and Power Quality Analyzer Presentation EN PDF

TE30 Electricity Meter Tester and Power Quality 1
www.calmet.com.pl Analyzer
Testing whole measurement system!
Accuracy of all kind of CT/PT burden,
Electricity Meters ε[%] ratio, phase shift
Electromechanical error
Meters
Connection
errors
Electronic (static)
Meters
4-Quadrants
Meters
Max Demand Power Quality

Meters
in point of
TE30 measurement
Measure of power network parameters and
Meters testing in accuracy class 0,05 or 0,1
Voltage range 0,05…300V
Current range
0,001…12(100)(1000)(30/300/3000)A
Testing of energy meters, potential and
current transformers (CT / PT)
Recording and analyse of Power Quality
Vector, oscilloscope, bar and trend charts
of three phase network
Automatic Meter Constant recognition
Automatic setting of measurement
conditions
Powering from measurement network
50…450V AC and from internal battery with its
own charger
Big 7-inch full colour touch screen and
computer software Calmet TE30 PC soft
Reading data and remote controlled via
USB, Ethernet, Bluetooth
Recording data on flash memory SD card up
to 32GB
Calibration Certificate
TE30 Analyzer Inputs, Outputs and Connectors: Current Clip – on CT
socket
Photo Scanning
Head Impulse Input
Current I1, I2, I3
sockets
SD Memory Card
socket
Power ON / OFF
switch
Mini USB Connector

Protective Fuse
Ethernet socket
Voltage U1, U2, U3,

Un sockets
Power cord socket
High Voltage sensors or

Battery
Current Clamps socket
compartment at the
rear side
All possible types of connection: 1P2W, 3P4W, 3P3W, ... , direct or with clamps
Electricity meter testing – direct connection Electricity meter testing – connection with clamps
1 3 4 6 7 9 10 12 1 3 4 6 7 9 10 12
L1 L1
L2 L2
L3 L3
N N
Electricity meter (CT) testing – direct connection Electricity meter testing (CT) – connection with clamps
1 2 3 4 5 6 7 8 9 11 1 2 3 4 5 6 7 8 9 11
S1S2 S1S2 S1S2 S1S2 S1S2 S1S2
P1 P2 P1 P2 P1 P2 P1 P2 P1 P2 P1 P2
L1 L1
L2 L2
L3 L3
N N
RMS measurement results and TE30 Analyzer configuration:
3-Phase Star or Voltage direct connection Automatic or Costant range used Actual Date and
Delta connection Current mesured by flexible clamps for measurements Time
Voltage Phase - Frequency

Neutral
Neutral Voltage
Voltage Phase -
Phase Neutral Current
Current 3-Phase Power
Factor
Phase shift
3-Phase Reactive
Power Factor Factor
Reactive Factor 3-Phase Tangent ϕ
Tangent ϕ 3-Phase Vector

Rotation
Phase shift between 3-Phase Active
Voltages Power
Active Power P 3-Phase Reactive
Power
Reactive Power Q
3-Phase Apparent
Apparent Power S Power
Vector diagram with calculated Un & In Oscilloscope of U1, U2, U3, I1, I2, I3
Time trend of U, I, P, Q, φ, f, PF, …. Harmonics table & bar diagram

Energy meter testing on site and laboratory
function of computing meter error

(partial errors, average errorr, standard
deviation) directly in percentages [%]
with method of setting time of
measurement or number of impulses,
function of automatic identification
energy meter constant,
function of automatic determining
measurement time or number of pulses.
Results of testing are presented as:
← TABLE
CHART →
Energy meter Register testing on site and laboratory
function of energy measurement with method of
setting time periods for verification of energy meter
Register directly in percent [%],
function of energy measuremnt for
power P, P+, P-, Q, Q+, Q-, S,
function of energy measurement for
the first (fundamental) harmonic of
active power PH1 and reactive power
QH1
IEC 62053-24/Ed.1 Static meters for

Maximum Demand Energy meter testing reactive energy at fundamental
frequency (classes 0,5 S, 1 S and 1)
function of maximum power measuring for

testing of maximum demand energy meters,
CT, PT Transformers testing (LV & MV, voltage and current, simultaneously in
three phases) directly on site: ratio error and phase shift error testing
Connection diagram
CT Ratio error and phase error testing
1 2 3 4 5 6 7 8 9 11
function of computing
S1 S2 S1 S2 S1 S2
transformer ratio error
L1
P1
P
P1
P
P1
P
directly in percent [%]
2 2 2
L2
L3
N
function of computing phase
shift error [°]
CT, PT Transformers testing (LV i MV, voltage and current, simultaneously in
three phases) directly on site: CT / PT burden testing
Test can be done by taking into

account the length (L) and cross-
section of connection wires and
serial fuse (Rf) resistance
CT Burden testing
1 2 3 4 5 6 7 8 9 11
S1 S2 S1 S2
Why the tranformer burden
S1 S2
L1
P1
P
P1
P
P1
P
(load) is so important?!
2 2 2
L2
L3
N
CT Transformer testing: burden testing
CT – current transformer can operate with
ε – ratio error [%]
stated accuracy only between 25% - 100% of
burden (load). In case of too long, or too thin
Limit of
wire dimension or too small load, the result,
accuracy secondary current can be out of accuracy limits
[%] transformer power rating Sn
25% 100%
Normal work
area
Sn=5VA 1 2 3 4 5 6 7 8 9 11
Ip Is Connection wires
L=10m
Example (power loss in cables):
Us1 Us2 mm2
ρCU ⋅ l 0,0175Ω m ⋅ 2 ⋅10m
RP = = = 0,35Ω
S 1mm2
Current transformer PP = I 2 2 ⋅ RP = 52 A ⋅ 0,35Ω = 8, 75VA
Function of power quality analyser + recording
measuring of power quality parameters according to IEC 61000-4-30 class A with

visualization of measurement results in the real time mode
analyzing of measurement
results for EN 50160
compatibility or individual
requirements of user
recording of power network parameters in the SD Flash 4-32GB memory, which gives
(8÷64)x106 sets of network parameters or long-term registration of power quality
Function of power quality analyser + recording
selecting recording method: average

value, max / min value, outside
limits, every Energy Meter error
selecting recorded parametrs and
averaging times
selecting time length of recording

and start date & time
TE30 Analyzer's equipment delivered in price:
- TE30 Analyzer class 0.05 or 0.1;
- Power supply cord;
- Fuse T250mA@230V or T500mA@110V (2 units);
- Memory SD card (8GB);
- Operation manual of analyzer;
- Warranty card;
- Manufacturer calibration certificate;
TE30 Analyzer's optional equipment:
• Calmet TE30 PC Soft with operation manual
(for Windows XP and higher versions) and
USB mini / USB A interface cable,
• AD100EXT extension for powering TE30 from

measurement network,
• EA30 set of safety measurement cables

(10pcs) for voltage and current,
• AKD100 additional accessories (handlers,

terminals, aligator clips, fork, banana plugs -
42pcs) for safety cables,
• CF102 photo head with holder for inductive
meter and meter with LED,
• DR200B miniature thermal printer with

Bluetooth,
• ET30 transportation case,
• ET32 transportation case for additional

accessories,
• CT10AC electronic compensated clamps up to
10A (1compl),
• CT100AC electronic compensated clamps up

to 100A (1compl),
• CT1000AC electronic compensated clamps up

to 1000A (1compl),
• FCT3000AC electronic compensated flexible

clamps in ranges 30/300/3000A (1compl),
• AmpLiteWire 2000A primary current sensors
up to 2000A for LV and MV nets (1pc),
• VoltLiteWire 40kV primary sensors up to

40kV (1pc),
• rechargeable battery NiMH

AA R6 1.2V 2700mAh (5pcs),
• TE30 option set 01

(TE30+ET30+CT100AC+
+CF102+EA30+AKD100).
TE30 Analyzer set
ready for operation
Contact:
Calmet Ltd., Kukulcza 18 Street, 65-472 Zielona Gora, Poland EU
www.calmet.com.pl e-mail: [email protected]
Tel.: +48 68 324 04 56 Fax: +48 68 324 04 57

TE30 Electricity Meter Tester and Power Quality Analyzer Presentation EN PDF

Uploaded by

Copyright:

Available Formats

TE30 Electricity Meter Tester and Power Quality Analyzer Presentation EN PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

TE30 Electricity Meter Tester and Power Quality Analyzer Presentation EN PDF

Uploaded by

Copyright:

Available Formats

TE30 Electricity Meter Tester and Power Quality 1

Max Demand Power Quality

Mini USB Connector

Voltage U1, U2, U3,

Power cord socket

High Voltage sensors or

S1S2 S1S2 S1S2 S1S2 S1S2 S1S2

Voltage Phase - Frequency

Tangent ϕ 3-Phase Vector

Time trend of U, I, P, Q, φ, f, PF, …. Harmonics table & bar diagram

function of computing meter error

Results of testing are presented as:

IEC 62053-24/Ed.1 Static meters for

function of maximum power measuring for

Test can be done by taking into

measuring of power quality parameters according to IEC 61000-4-30 class A with

selecting recording method: average

selecting time length of recording

• AD100EXT extension for powering TE30 from

• EA30 set of safety measurement cables

• AKD100 additional accessories (handlers,

• DR200B miniature thermal printer with

• ET30 transportation case,

• ET32 transportation case for additional

• CT100AC electronic compensated clamps up

• CT1000AC electronic compensated clamps up

• FCT3000AC electronic compensated flexible

• VoltLiteWire 40kV primary sensors up to

• rechargeable battery NiMH

• TE30 option set 01

You might also like