Scribd Logo
Upload

Welcome to Scribd!

  • 356 views

    Clio Brakes Abs Tn.3588a - Xbxx-5

    Uploaded by

    dario024
    The rear wheel speed sensor is removed by taking off the wheel, loosening the T30 sensor mounting bolt, and disconnecting the sensor connector. When refitting, the sensor is coated with grease, refitted in reverse order, and the gap is checked with shims to ensure proper connection and prevent breakdowns. The pressure sensor tracks brake fluid pressure and must be replaced along with the hydraulic unit.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Clio Brakes Abs Tn.3588a - Xbxx-5

    Uploaded by

    dario024
    356 views2 pages
    The rear wheel speed sensor is removed by taking off the wheel, loosening the T30 sensor mounting bolt, and disconnecting the sensor connector. When refitting, the sensor is coated with grease, refitted in reverse order, and the gap is checked with shims to ensure proper connection and prevent breakdowns. The pressure sensor tracks brake fluid pressure and must be replaced along with the hydraulic unit.

    Original Description:

    ABS Renault Clio 5

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The rear wheel speed sensor is removed by taking off the wheel, loosening the T30 sensor mounting bolt, and disconnecting the sensor connector. When refitting, the sensor is coated with grease, refitted in reverse order, and the gap is checked with shims to ensure proper connection and prevent breakdowns. The pressure sensor tracks brake fluid pressure and must be replaced along with the hydraulic unit.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    356 views2 pages

    Clio Brakes Abs Tn.3588a - Xbxx-5

    Uploaded by

    dario024
    The rear wheel speed sensor is removed by taking off the wheel, loosening the T30 sensor mounting bolt, and disconnecting the sensor connector. When refitting, the sensor is coated with grease, refitted in reverse order, and the gap is checked with shims to ensure proper connection and prevent breakdowns. The pressure sensor tracks brake fluid pressure and must be replaced along with the hydraulic unit.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    ANTI-LOCK BRAKING SYSTEM

    Rear wheel speed sensor 38C


    REMOVAL
    TIGHTENING TORQUE (in daNm)
    Remove:
    Sensor mounting bolt 0.8 ± 0.2
    – the wheel,
    – the T30 sensor mounting bolt (1) (with T30 Torx
    The Target/Sensor gap (e) must be between 0.21 mm indentation).
    and 1.5 mm.

    Remove the connector from the support.

    Disconnect the wheel sensor connector.

    Remove the sensor.

    REFITTING

    Coat the sensor with multifunction grease

    Part number: 77 01 422 308.

    Refit the sensor in the reverse order to removal.

    The gap on a sensor turn can be checked using a set


    of shims.

    NOTE: It is vital to make sure that the connectors


    are perfectly connected to prevent risk of
    breakdowns.

    The sensor must be fitted manually. Do not knock it


    during installation.

    38C-12
    ANTI-LOCK BRAKING SYSTEM
    Pressure sensor 38C

    ALLOCATION OF SENSOR TRACKS

    Track Description
    1 Earth
    2 Pressure signal
    3 Stabilized supply

    Pressure sensor (1) informs the computer of the brake


    fluid pressure at the hydraulic unit inlet.

    REPLACEMENT

    If you replace the sensor, you must also replace the


    hydraulic unit (see the hydraulic unit removal-refitting
    method).

    38C-13

    You might also like