Scribd
Upload
226 views4 pages

Powerwand Instructions by Chrystalk: - Original Message - From: "Chrystal Kay"

The document provides instructions for building a Power Wand device using various crystals, metals, and electrical components. It includes a parts list and step-by-step directions for assembling the wand which involves wrapping crystals with wire in specific patterns, embedding them in resin in a copper pipe with additional crystals and metals, and connecting it to a frequency box using screws. The overall goal is to create a wand that can be used to generate and project orgone energy.

Uploaded by

lighteagles131
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
226 views4 pages

Powerwand Instructions by Chrystalk: - Original Message - From: "Chrystal Kay"

The document provides instructions for building a Power Wand device using various crystals, metals, and electrical components. It includes a parts list and step-by-step directions for assembling the wand which involves wrapping crystals with wire in specific patterns, embedding them in resin in a copper pipe with additional crystals and metals, and connecting it to a frequency box using screws. The overall goal is to create a wand that can be used to generate and project orgone energy.

Uploaded by

lighteagles131
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

PowerWand Instructions by Chrystalk 1

PowerWand Instructions by Chrystalk

---Original message---
From: "Chrystal Kay"

http://www.ryanmcginty.com/orgone/pwinstructions.htm 28 August 2009 12:04:36 PM


PowerWand Instructions by Chrystalk 2

From: "Chrystal Kay"

>Don's Power Wand


>
Parts List:
1- 3" copper pipe, 9" long
1- copper cap for pipe
1- dixie cup that will fit snugly in end
1- 7" by 1" dia SP crystal
1- roll blue magnet wire from Radio Shack
2- 2" drywall screws
Shrink wrap tubing- op.
99" 18 gage bare wire
tape
Goop glue
Metal filling- 1/2 copper at least, and
aluminum
Resin and catalyst
1- 1" Amethyst point
1/4tsp. Pyrite grains
4- 12mm Hematite beads
4 or 5- rough round Garnets
Frequency box w/alligator clip connectors.
Silicon spray ( or WD-40 )

Instructions:

Preparing large crystal:

Start at the bottom of the crystal. ( make


the 'ears' that will stick out
rather long- 2-3") Using magnet wire, make a
six wrap mobius knot , and
continue below that and make a second six
wrap mobius knot. Continue to make
a total of six- six wrap mobius knots from
the same continuous piece of

http://www.ryanmcginty.com/orgone/pwinstructions.htm 28 August 2009 12:04:36 PM


PowerWand Instructions by Chrystalk 3

wire. ( look in Don's files to see how to


twist the wire for the knot.)

Now attach 2- screws to 'ears' by firmly


wrapping around threads and either
shrink wrap or goop glue well. ( no bare
wire or screw length exposed) Leave
only the head exposed. Tape to crystal to
hold in place while pouring, head
ends up beyond end of crystal.

With the entire length of bare wire, wrap


the crystal from top to bottom
counter clockwise. (there is a reason for
that)

On to the assembly:

This project is made beginning with the TOP.


Fit your Dixie cup into the top end of the
pipe, (flat side in) and trim
flush with rim. Cut x in bottom and insert
point of large crystal, from the
bottom of the cup, up.( Don does this so
point will be below the rim of the
pipe.) Glue well around crystal and glue
cup in place flush with rim.

Now turn over, bottom side up.


Put just enough metal and resin in to cover
cup and meeting place of crystal
and cup bottom. Let harden. (Less leaks
this way!)

Add metal to position amethyst in. Place


amethyst point down next to

http://www.ryanmcginty.com/orgone/pwinstructions.htm 28 August 2009 12:04:36 PM


PowerWand Instructions by Chrystalk 4

crystal pointing same way, and add catalyzed


resin.( Let firm up between
each layer.)

Sprinkle pyrite in, add metal and pour on


resin.

Add Hematite, add metal and pour on resin.


You should be pretty close to the top by
now...say 2 1/2" or so.
Add Garnets, add metal to beneath top of
screws. Let cure.

Trim off any boo boos or leaks.

Attach frequency box clips to screw ends.


The frequency box will fit handily into the
cap. With some spray around the
edge of the pipe rim, it shouldn't be too
hard to remove the cap for
changing the battery.

How did I do Don?

http://www.ryanmcginty.com/orgone/pwinstructions.htm 28 August 2009 12:04:36 PM

You might also like