SAP2000 Analysis Report

Model Name:

7 January 2018
type 2.sdb SAP2000 v19.2.0 - License #3010*17WPD8FQY83BAK4

Design preferences 07 January 2018

Contents
1. Model geometry................................................................................. Error: Reference source not found
1.1. Joint coordinates............................................................................................................................ 5
1.2. Joint restraints................................................................................................................................ 5
1.3. Element connectivity...................................................................................................................... 5
2. Material properties................................................................................................................................. 6
3. Section properties.................................................................................................................................. 6
3.1. Frames........................................................................................................................................... 6
3.2. Solids............................................................................................................................................. 7
4. Load patterns......................................................................................................................................... 7
4.1. Definitions...................................................................................................................................... 7
5. Load cases........................................................................................................................................... 10
5.1. Definitions.................................................................................................................................... 10
5.2. Static case load assignments....................................................................................................... 10
5.3. Response spectrum case load assignments................................................................................ 10
6. Load combinations............................................................................................................................... 11
7. Structure results................................................................................................................................... 12
7.1. Mass summary............................................................................................................................. 12
7.2. Modal results................................................................................................................................ 12
7.3. Base reactions............................................................................................................................. 13
8. Joint results.......................................................................................................................................... 13
9. Frame results....................................................................................................................................... 14
10. Material take-off................................................................................................................................. 16
11. Design preferences............................................................................................................................ 16
11.1. Steel design................................................................................................................................ 16
12. Design overwrites.......................................................................................................................... 16
12.1. Steel design............................................................................................................................... 16
13. Design summary................................................................................................................................ 18
13.1. Steel design............................................................................................................................... 18

List of Figures
Figure 1: Finite element model................................................................................................................... 5
Figure 2: Deformed shape....................................................................................................................... 12

List of Tables
Table 1: Joint Coordinates.......................................................................................................................... 5
Table 2: Joint Restraint Assignments......................................................................................................... 5
Table 3: Connectivity - Frame.................................................................................................................... 6
Table 4: Frame Section Assignments......................................................................................................... 6
Table 5: Material Properties 02 - Basic Mechanical Properties.................................................................. 6
Table 6: Material Properties 03a - Steel Data............................................................................................. 6
Table 8: Frame Section Properties 01 - General, Part 1 of 4...................................................................... 6
Table 8: Frame Section Properties 01 - General, Part 2 of 4...................................................................... 7

Page 2 of 28
type 2.sdb SAP2000 v19.2.0 - License #3010*17WPD8FQY83BAK4

Design preferences 07 January 2018

Table 8: Frame Section Properties 01 - General, Part 3 of 4...................................................................... 7
Table 8: Frame Section Properties 01 - General, Part 4 of 4...................................................................... 7
Table 9: Solid Property Definitions............................................................................................................. 7
Table 10: Load Pattern Definitions............................................................................................................. 7
Table 11: Load Case Definitions, Part 1 of 2............................................................................................ 10
Table 11: Load Case Definitions, Part 2 of 2............................................................................................ 10
Table 12: Case - Static 1 - Load Assignments.......................................................................................... 10
Table 13: Function - Response Spectrum - User...................................................................................... 10
Table 14: Combination Definitions............................................................................................................ 11
Table 15: Assembled Joint Masses, Part 1 of 2........................................................................................ 12
Table 15: Assembled Joint Masses, Part 2 of 2........................................................................................ 12
Table 16: Modal Participating Mass Ratios.............................................................................................. 13
Table 17: Base Reactions........................................................................................................................ 13
Table 18: Joint Displacements.................................................................................................................. 13
Table 19: Joint Reactions......................................................................................................................... 14
Table 20: Element Forces - Frames, Part 1 of 2....................................................................................... 14
Table 20: Element Forces - Frames, Part 2 of 2....................................................................................... 15
Table 21: Material List 2 - By Section Property......................................................................................... 16
Table 22: Preferences - Steel Design - Indian IS 800:2007, Part 1 of 2................................................... 16
Table 22: Preferences - Steel Design - Indian IS 800:2007, Part 2 of 2................................................... 16
Table 26: Overwrites - Steel Design - Indian IS 800:2007, Part 1 of 5..................................................... 17
Table 26: Overwrites - Steel Design - Indian IS 800:2007, Part 2 of 5..................................................... 17
Table 26: Overwrites - Steel Design - Indian IS 800:2007, Part 3 of 5..................................................... 17
Table 26: Overwrites - Steel Design - Indian IS 800:2007, Part 4 of 5..................................................... 17
Table 26: Overwrites - Steel Design - Indian IS 800:2007, Part 5 of 5..................................................... 17
Table 27: Steel Design 1 - Summary Data - Indian IS 800:2007, Part 1 of 2............................................ 18
Table 27: Steel Design 1 - Summary Data - Indian IS 800:2007, Part 2 of 2............................................ 18

Page 3 of 28
type 2.sdb SAP2000 v19.2.0 - License #3010*17WPD8FQY83BAK4

Design preferences 07 January 2018

1 INTRODUCTION

1.1 About this Report

This report deals with methodology of the structural analysis carried out for predominant wind loading
of the Structure. It includes the result of structural analysis of the current structure and its component
design required for its intended use as per the current code provisions.

1.2 About the Structure

The structure is Steel framed structure with shed of the Indian Plate sections which are extensively used
for supporting the solar Panel. In the shed the UPVC roofing sheet is used for covering. The foundation is
laid on isolated footing with the provision of appropriate anchor bolts.

1.3 Analysis procedure

The structure has been modelled, analyzed and designed in computer software “SAP2000 V19”. The
software has very good analysis and design capability .It is a Finite Element Method (FEM) based
software and requires modelling of the structure by finite-elements. Most likely the structure is modelled
on the basis of 3D space frame model and the loading is applied in the respective plane with the code
provision. Hence the obtained response is used by software to evaluate the sufficient strength required
for the provided section.

Page 4 of 28
type 2.sdb SAP2000 v19.2.0 - License #3010*17WPD8FQY83BAK4

Design preferences 07 January 2018

1. Model geometry
This section provides model geometry information, including items such as joint coordinates, joint
restraints, and element connectivity.

Figure 1: Finite element model

1.1. Joint coordinates

Table 1: Joint Coordinates

Table 1: Joint Coordinates
Joint CoordSys CoordType GlobalX GlobalY GlobalZ
m m m
7 GLOBAL Cartesian 0. 0. 0.275
8 GLOBAL Cartesian 0.097 0. 0.3
12 GLOBAL Cartesian 0.097 0. 0.
13 GLOBAL Cartesian 0.597 0. 0.
14 GLOBAL Cartesian 0.597 0. 0.04
15 GLOBAL Cartesian 0.694 0. 0.065

1.2. Joint restraints

Table 2: Joint Restraint Assignments

Table 2: Joint Restraint Assignments
Joint U1 U2 U3 R1 R2 R3

12 Yes Yes Yes Yes Yes Yes

13 Yes Yes Yes Yes Yes Yes

1.3. Element connectivity

Page 5 of 28
type 2.sdb SAP2000 v19.2.0 - License #3010*17WPD8FQY83BAK4

Design preferences 07 January 2018

Table 3: Connectivity - Frame
Table 3: Connectivity - Frame
Frame JointI JointJ Length
m
10 8 12 0.3
11 12 13 0.5
12 13 14 0.04
14 7 8 0.10017
16 14 15 0.10017

Table 4: Frame Section Assignments

Table 4: Frame Section Assignments
Frame AnalSect DesignSect MatProp

10 Plate Section Plate Section Default

11 Plate Section Plate Section Default
12 Plate Section Plate Section Default
14 Plate Section Plate Section Default
16 Plate Section Plate Section Default

2. Material properties
This section provides material property information for materials used in the model.

Table 5: Material Properties 02 - Basic Mechanical Properties

Table 5: Material Properties 02 - Basic Mechanical Properties
Material UnitWeight UnitMass E1 G12 U12 A1
KN/m3 KN-s2/m4 KN/m2 KN/m2 1/C
Fe250 7.6973E+01 7.8490E+00 199947978 76903068. 0.3 1.1700E-05
.8 77

Table 6: Material Properties 03a - Steel Data

Table 6: Material Properties 03a - Steel Data
Material Fy Fu FinalSlope
KN/m2 KN/m2
Fe250 250000. 287500. -0.1

3. Section properties
This section provides section property information for objects used in the model.

3.1. Frames

Table 8: Frame Section Properties 01 - General, Part 1 of 4

Table 8: Frame Section Properties 01 - General, Part 1 of 4
SectionName Material Shape t3 t2 Area TorsConst I33 I22
m m m2 m4 m4 m4

Page 6 of 28
type 2.sdb SAP2000 v19.2.0 - License #3010*17WPD8FQY83BAK4

Design preferences 07 January 2018

Plate Section Fe250 Rectangular 0.005 0.1 0.0005 4.035E-09 1.042E-09 4.167E-07
rect section Fe250 Rectangular 0.005 0.04 0.0002 1.535E-09 4.167E-10 2.667E-08

Table 8: Frame Section Properties 01 - General, Part 2 of 4

Table 8: Frame Section Properties 01 - General, Part 2 of
4
SectionName I23 AS2 AS3
m4 m2 m2
Plate Section 0. 0.000417 0.000417
rect section 0. 0.000167 0.000167

Table 8: Frame Section Properties 01 - General, Part 3 of 4

Table 8: Frame Section Properties 01 - General, Part 3 of 4
SectionName S33 S22 Z33 Z22 R33 R22
m3 m3 m3 m3 m m
Plate Section 4.167E-07 8.333E-06 6.250E-07 0.000013 0.001443 0.028868
rect section 1.667E-07 1.333E-06 2.500E-07 2.000E-06 0.001443 0.011547

Table 8: Frame Section Properties 01 - General, Part 4 of 4

Table 8: Frame Section Properties 01 - General, Part 4 of 4
SectionName AMod A2Mod A3Mod JMod I2Mod I3Mod MMod WMod

Plate Section 1. 1. 1. 1. 1. 1. 1. 1.
rect section 1. 1. 1. 1. 1. 1. 1. 1.

3.2. Solids

Table 9: Solid Property Definitions

Table 9: Solid Property Definitions
SolidProp Material MatAngleA MatAngleB MatAngleC
Degrees Degrees Degrees
Solid1 4000Psi 0. 0. 0.

4. Load patterns
This section provides loading information as applied to the model.

4.1. Definitions

Table 10: Load Pattern Definitions

Table 10: Load Pattern Definitions
LoadPat DesignType SelfWtMult AutoLoad

DEAD Dead 1.
Solar panel Dead 0.
Wind Wind 0. IS 875-2015

Page 7 of 28
type 2.sdb SAP2000 v19.2.0 - License #3010*17WPD8FQY83BAK4

Design preferences 07 January 2018

2 LOADING

For analysis and design of the structure , all loadings (dead loads , live loads and wind loads) are
calculated based on different parts of IS875:1987 (NBC has been used wherever applicable).

2.1 Dead Loads (DL)

These are the permanent load which is not supposed to change during the structure’s design life. The
dead loads included in the design are:
a. Unit-weight of materials:
i. Solar Panel 15 kg/m2(assumed)
ii. Steel : 76.97 KN/m3(7697 Kg/m3)

2.2 Wind Load (WL)

Wind load has been calculated based on NBC104 and IS 875:1987 Part 3. And hence obtained wind load
is used in the Purlins and Runners as uniform member load and in support as point load.

2.3 Wind Load Calculation

A) Wind pressure in Roof Sign Input Unit

Basic wind speed Vb 47.00 m/sec

Probability Factor k1 0.96

Terrain/height/size factor k2 0.94

Topography factor k3 1.00 refer code IS 875 Part 3
Design wind speed Vz 38.54 m/sec
Design wind Pressure Pd 1054.715 N/m2
Height to width ratio H/w 0.43
Pitching angle φ 34.00 degree
Structure type B
Terrain category 3
Structure class General Building 50.00
Wall opening > 20% wall opening
1) For Wind normal to ridge
External wind pressure coefficient windward Cpe -0.40
(choose appropriate from Table B7 and B9)

Page 8 of 28
type 2.sdb SAP2000 v19.2.0 - License #3010*17WPD8FQY83BAK4

Design preferences 07 January 2018

For windward slope Cpe -0.18

External wind pressure coefficient leeward Cpe -0.40
For leeward slope Cpe -0.40

Internal pressure coeff. For normal permeability

Cpi 0.50
Cpi -0.50

Combined external and internal wind pressure

Windward slope 464.14 N/m2
783.54 N/m2
leeward slope 267.36 N/m2
980.32 N/m2
2) Wind parallel to ridge
External wind pressure coefficient Cpe
On both slops for 1/4 th length of building Cpe -0.70
On both slops for 1/2 th length of building Cpe -0.60

Internal pressure coeff. For normal permeability Cpi 0.50

Cpi -0.50

Combined External + Internal wind pressure

On both slopes for 1/4 th length of building - N/m2
-1,247.68 N/m2
On both slopes for 1/2 th length of building 89.12 N/m2
-1,247.68 N/m2
So the design wind pressure is 464.14 Downward
and -1,247.68 Upward

Page 9 of 28
type 2.sdb SAP2000 v19.2.0 - License #3010*17WPD8FQY83BAK4

Design preferences 07 January 2018

5. Load cases
This section provides load case information.

5.1. Definitions

Table 11: Load Case Definitions, Part 1 of 2

Table 11: Load Case Definitions, Part 1 of 2
Case Type InitialCond ModalCase BaseCase MassSource DesActOpt

DEAD LinStatic Zero Prog Det

MODAL LinModal Zero Prog Det
Solar panel LinStatic Zero Prog Det
Wind LinStatic Zero Prog Det

Table 11: Load Case Definitions, Part 2 of 2

Table 11: Load Case
Definitions, Part 2 of 2
Case DesignAct

DEAD Non-
Composite
MODAL Other
Solar panel Non-
Composite
Wind Short-Term
Composite

5.2. Static case load assignments

Table 12: Case - Static 1 - Load Assignments

Table 12: Case - Static 1 - Load Assignments
Case LoadType LoadName LoadSF

DEAD Load pattern DEAD 1.

Solar panel Load pattern Solar panel 1.
Wind Load pattern Wind 1.

5.3. Response spectrum case load assignments

Table 13: Function - Response Spectrum - User

Table 13: Function - Response Spectrum - User
Name Period Accel FuncDamp
Sec

Page 10 of 28
type 2.sdb SAP2000 v19.2.0 - License #3010*17WPD8FQY83BAK4

Design preferences 07 January 2018

UNIFRS 0. 1. 0.05
UNIFRS 1. 1.

6. Load combinations
This section provides load combination information.

Table 14: Combination Definitions

Table 14: Combination Definitions
ComboName ComboType CaseName ScaleFactor

DSTL1 Linear Add DEAD 1.5

DSTL1 Solar panel 1.5
DSTL2 Linear Add DEAD 1.2
DSTL2 Solar panel 1.2
DSTL2 Wind 0.6
DSTL3 Linear Add DEAD 1.2
DSTL3 Solar panel 1.2
DSTL3 Wind -0.6
DSTL4 Linear Add DEAD 1.2
DSTL4 Solar panel 1.2
DSTL4 Wind 1.2
DSTL5 Linear Add DEAD 1.2
DSTL5 Solar panel 1.2
DSTL5 Wind -1.2
DSTL6 Linear Add DEAD 1.5
DSTL6 Solar panel 1.5
DSTL6 Wind 1.5
DSTL7 Linear Add DEAD 1.5
DSTL7 Solar panel 1.5
DSTL7 Wind -1.5
DSTL8 Linear Add DEAD 0.9
DSTL8 Solar panel 0.9
DSTL8 Wind 1.5
DSTL9 Linear Add DEAD 0.9
DSTL9 Solar panel 0.9
DSTL9 Wind -1.5
DSTL10 Linear Add DEAD 1.
DSTL10 Solar panel 1.

Page 11 of 28
type 2.sdb SAP2000 v19.2.0 - License #3010*17WPD8FQY83BAK4

Design preferences 07 January 2018

7. Structure results
This section provides structure results, including items such as structural periods and base reactions.

Figure 2: Deformed shape

7.1. Mass summary

Table 15: Assembled Joint Masses, Part 1 of 2

Table 15: Assembled Joint Masses, Part 1 of 2
Joint MassSource U1 U2 U3 R1 R2 R3 CenterX
KN-s2/m KN-s2/m KN-s2/m KN-m-s2 KN-m-s2 KN-m-s2 m
7 Seismic 5.726E-02 5.726E-02 5.726E-02 0. 0. 0. 0.
Weight
8 Seismic 4.569E-02 4.569E-02 4.569E-02 0. 0. 0. 0.097
Weight
12 Seismic 1.570E-03 1.570E-03 1.570E-03 0. 0. 0. 0.097
Weight
13 Seismic 1.060E-03 1.060E-03 1.060E-03 0. 0. 0. 0.597
Weight
14 Seismic 5.734E-02 5.734E-02 5.734E-02 0. 0. 0. 0.597
Weight
15 Seismic 4.510E-02 4.510E-02 4.510E-02 0. 0. 0. 0.694
Weight
SumAccelUX Seismic 0.21 0. 0. 0. 0. 0. 0.3401
Weight
SumAccelUY Seismic 0. 0.21 0. 0. 0. 0. 0.3401
Weight
SumAccelUZ Seismic 0. 0. 0.21 0. 0. 0. 0.3401
Weight

Table 15: Assembled Joint Masses, Part 2 of 2

Table 15: Assembled Joint Masses, Part 2 of 2
Joint MassSource CenterY CenterZ
m m
7 Seismic 0. 0.275
Weight
8 Seismic 0. 0.3
Weight
12 Seismic 0. 0.
Weight
13 Seismic 0. 0.
Weight
14 Seismic 0. 0.04
Weight
15 Seismic 0. 0.065
Weight
SumAccelUX Seismic 0. 0.16671
Weight
SumAccelUY Seismic 0. 0.16671
Weight
SumAccelUZ Seismic 0. 0.16671
Weight

7.2. Modal results

Page 12 of 28
type 2.sdb SAP2000 v19.2.0 - License #3010*17WPD8FQY83BAK4

Design preferences 07 January 2018

Table 16: Modal Participating Mass Ratios
Table 16: Modal Participating Mass Ratios
OutputCase StepNum Period UX UY UZ SumUX SumUY SumUZ
Sec
MODAL 1. 0.41975 0.42921 0. 0.03892 0.42921 0. 0.03892
MODAL 2. 0.144186 0. 0.28386 0. 0.42921 0.28386 0.03892
MODAL 3. 0.106675 0.07203 0. 0.23212 0.50124 0.28386 0.27104
MODAL 4. 0.082696 0.05353 0. 0.18904 0.55477 0.28386 0.46008
MODAL 5. 0.04665 0. 0.22038 0. 0.55477 0.50425 0.46008
MODAL 6. 0.014999 0.44522 0. 0.02302 0.99999 0.50425 0.48309
MODAL 7. 0.014478 0. 0.21738 0. 0.99999 0.72163 0.48309
MODAL 8. 0.002377 1.486E-08 1.338E-17 0.22982 0.99999 0.72163 0.71291
MODAL 9. 0.001844 0. 0.27837 9.651E-16 0.99999 1. 0.71291
MODAL 10. 0.00107 7.284E-06 5.784E-17 0.12731 1. 1. 0.84022
MODAL 11. 0.000999 2.041E-10 2.338E-17 0.00039 1. 1. 0.84061
MODAL 12. 0.0009 6.796E-07 8.770E-16 0.15939 1. 1. 1.

7.3. Base reactions

Table 17: Base Reactions

Table 17: Base Reactions
OutputCase GlobalFX GlobalFY GlobalFZ GlobalMX GlobalMY GlobalMZ
KN KN KN KN-m KN-m KN-m
DEAD 1.193E-15 0. 0.04 0. -0.0114 0.
Solar panel 3.435E-13 0. 2. 0. -0.6861 0.
Wind 0. 0. 0. 0. 0. 0.

8. Joint results
This section provides joint results, including items such as displacements and reactions.

Table 18: Joint Displacements

Table 18: Joint Displacements
Joint OutputCase U1 U2 U3 R1 R2 R3
m m m Radians Radians Radians
7 DEAD -0.000033 0. -0.000028 0. -0.000299 0.
7 Solar panel -0.009304 0. -0.007876 0. -0.082377 0.
7 Wind 0. 0. 0. 0. 0. 0.
8 DEAD -0.00004 0. -2.889E-08 0. -0.000269 0.
8 Solar panel -0.011333 0. -3.001E-06 0. -0.075556 0.
8 Wind 0. 0. 0. 0. 0. 0.
12 DEAD 0. 0. 0. 0. 0. 0.
12 Solar panel 0. 0. 0. 0. 0. 0.
12 Wind 0. 0. 0. 0. 0. 0.
13 DEAD 0. 0. 0. 0. 0. 0.
13 Solar panel 0. 0. 0. 0. 0. 0.
13 Wind 0. 0. 0. 0. 0. 0.
14 DEAD 7.182E-07 0. -1.850E-09 0. 0.000036 0.
14 Solar panel 0.000171 0. -4.001E-07 0. 0.008555 0.
14 Wind 0. 0. 0. 0. 0. 0.
15 DEAD 2.179E-06 0. -5.671E-06 0. 0.000066 0.
15 Solar panel 0.000489 0. -0.001236 0. 0.013474 0.
15 Wind 0. 0. 0. 0. 0. 0.

Page 13 of 28
type 2.sdb SAP2000 v19.2.0 - License #3010*17WPD8FQY83BAK4

Design preferences 07 January 2018

Table 19: Joint Reactions

Table 19: Joint Reactions
Joint OutputCase F1 F2 F3 M1 M2 M3
KN KN KN KN-m KN-m KN-m
12 DEAD 1.272E-15 0. 0.025 0. -6.148E-04 0.
12 Solar panel 3.595E-13 0. 1. 0. 0.0525 0.
12 Wind 0. 0. 0. 0. 0. 0.
13 DEAD -7.980E-17 0. 0.015 0. 6.148E-04 0.
13 Solar panel -1.599E-14 0. 1. 0. -0.0445 0.
13 Wind 0. 0. 0. 0. 0. 0.

9. Frame results
This section provides frame force results.

Table 20: Element Forces - Frames, Part 1 of 2

Table 20: Element Forces - Frames, Part 1 of 2
Frame Station OutputCase P V2 V3
m KN KN KN
10 0. DEAD -3.855E-03 1.272E-15 0.
10 0.15 DEAD -9.628E-03 1.272E-15 0.
10 0.3 DEAD -0.015 1.272E-15 0.
10 0. Solar panel -1. 3.595E-13 0.
10 0.15 Solar panel -1. 3.595E-13 0.
10 0.3 Solar panel -1. 3.595E-13 0.
10 0. Wind 0. 0. 0.
10 0.15 Wind 0. 0. 0.
10 0.3 Wind 0. 0. 0.
11 0. DEAD 0. -9.622E-03 0.
11 0.5 DEAD 0. 9.622E-03 0.
11 0. Solar panel 0. 0. 0.
11 0.5 Solar panel 0. 0. 0.
11 0. Wind 0. 0. 0.
11 0.5 Wind 0. 0. 0.
12 0. DEAD -5.395E-03 7.980E-17 0.
12 0.02 DEAD -4.625E-03 7.980E-17 0.
12 0.04 DEAD -3.855E-03 7.980E-17 0.
12 0. Solar panel -1. 1.599E-14 0.
12 0.02 Solar panel -1. 1.599E-14 0.
12 0.04 Solar panel -1. 1.599E-14 0.
12 0. Wind 0. 0. 0.
12 0.02 Wind 0. 0. 0.
12 0.04 Wind 0. 0. 0.
14 0. DEAD 7.105E-15 -7.321E-16 0.
14 0.046 DEAD 4.418E-04 1.714E-03 0.
14 0.046 DEAD 4.418E-04 1.714E-03 0.
14 0.05008 DEAD 4.811E-04 1.867E-03 0.
14 0.10017 DEAD 9.622E-04 3.733E-03 0.
14 0. Solar panel -1.819E-12 -2.052E-13 0.
14 0.046 Solar panel -1.819E-12 -2.052E-13 0.
14 0.046 Solar panel 0.25 0.968 0.
14 0.05008 Solar panel 0.25 0.968 0.
14 0.10017 Solar panel 0.25 0.968 0.
14 0. Wind 0. 0. 0.
14 0.046 Wind 0. 0. 0.
14 0.046 Wind 0. 0. 0.
14 0.05008 Wind 0. 0. 0.
14 0.10017 Wind 0. 0. 0.
16 0. DEAD -9.622E-04 -3.733E-03 0.

Page 14 of 28
type 2.sdb SAP2000 v19.2.0 - License #3010*17WPD8FQY83BAK4

Design preferences 07 January 2018

16 0.046 DEAD -5.203E-04 -2.019E-03 0.
16 0.046 DEAD -5.203E-04 -2.019E-03 0.
16 0.05008 DEAD -4.811E-04 -1.867E-03 0.
16 0.10017 DEAD 6.614E-17 -3.296E-17 0.
16 0. Solar panel -0.25 -0.968 0.
16 0.046 Solar panel -0.25 -0.968 0.
16 0.046 Solar panel 5.460E-14 -8.327E-15 0.
16 0.05008 Solar panel 5.460E-14 -8.327E-15 0.
16 0.10017 Solar panel 5.460E-14 -8.327E-15 0.
16 0. Wind 0. 0. 0.
16 0.046 Wind 0. 0. 0.
16 0.046 Wind 0. 0. 0.
16 0.05008 Wind 0. 0. 0.
16 0.10017 Wind 0. 0. 0.

Table 20: Element Forces - Frames, Part 2 of 2

Table 20: Element Forces - Frames, Part 2 of 2
Frame Station OutputCase T M2 M3
m KN-m KN-m KN-m
10 0. DEAD 0. 0. -1.870E-04
10 0.15 DEAD 0. 0. -1.870E-04
10 0.3 DEAD 0. 0. -1.870E-04
10 0. Solar panel 0. 0. -0.0525
10 0.15 Solar panel 0. 0. -0.0525
10 0.3 Solar panel 0. 0. -0.0525
10 0. Wind 0. 0. 0.
10 0.15 Wind 0. 0. 0.
10 0.3 Wind 0. 0. 0.
11 0. DEAD 0. 0. -8.018E-04
11 0.5 DEAD 0. 0. -8.018E-04
11 0. Solar panel 0. 0. 0.
11 0.5 Solar panel 0. 0. 0.
11 0. Wind 0. 0. 0.
11 0.5 Wind 0. 0. 0.
12 0. DEAD 0. 0. 1.870E-04
12 0.02 DEAD 0. 0. 1.870E-04
12 0.04 DEAD 0. 0. 1.870E-04
12 0. Solar panel 0. 0. 0.0445
12 0.02 Solar panel 0. 0. 0.0445
12 0.04 Solar panel 0. 0. 0.0445
12 0. Wind 0. 0. 0.
12 0.02 Wind 0. 0. 0.
12 0.04 Wind 0. 0. 0.
14 0. DEAD 0. 0. -2.439E-19
14 0.046 DEAD 0. 0. -3.943E-05
14 0.046 DEAD 0. 0. -3.943E-05
14 0.05008 DEAD 0. 0. -4.674E-05
14 0.10017 DEAD 0. 0. -1.870E-04
14 0. Solar panel 0. 0. -1.665E-16
14 0.046 Solar panel 0. 0. 9.271E-15
14 0.046 Solar panel 0. 0. 9.271E-15
14 0.05008 Solar panel 0. 0. -0.004
14 0.10017 Solar panel 0. 0. -0.0525
14 0. Wind 0. 0. 0.
14 0.046 Wind 0. 0. 0.
14 0.046 Wind 0. 0. 0.
14 0.05008 Wind 0. 0. 0.
14 0.10017 Wind 0. 0. 0.
16 0. DEAD 0. 0. -1.870E-04
16 0.046 DEAD 0. 0. -5.468E-05
16 0.046 DEAD 0. 0. -5.468E-05
16 0.05008 DEAD 0. 0. -4.674E-05

Page 15 of 28
type 2.sdb SAP2000 v19.2.0 - License #3010*17WPD8FQY83BAK4

Design preferences 07 January 2018

16 0.10017 DEAD 0. 0. -3.456E-19
16 0. Solar panel 0. 0. -0.0445
16 0.046 Solar panel 0. 0. -4.649E-16
16 0.046 Solar panel 0. 0. -4.649E-16
16 0.05008 Solar panel 0. 0. -4.309E-16
16 0.10017 Solar panel 0. 0. -1.385E-17
16 0. Wind 0. 0. 0.
16 0.046 Wind 0. 0. 0.
16 0.046 Wind 0. 0. 0.
16 0.05008 Wind 0. 0. 0.
16 0.10017 Wind 0. 0. 0.

10. Material take-off

This section provides a material take-off.

Table 21: Material List 2 - By Section Property

Table 21: Material List 2 - By Section Property
Section ObjectType NumPieces TotalLength TotalWeight
m KN
Plate Section Frame 5 1.04034 0.04

11. Design preferences

This section provides the design preferences for each type of design, which typically include material
reduction factors, framing type, stress ratio limit, deflection limits, and other code specific items.

11.1. Steel design

Table 22: Preferences - Steel Design - Indian IS 800:2007, Part 1 of 2

Table 22: Preferences - Steel Design - Indian IS 800:2007, Part 1 of 2
FrameType PatLLF SRatioLimit GammaM0 GammaM1 GammaM2 SeisCode SeisLoad

SMF 0.75 0.95 1.1 1.25 1.25 Yes Yes

Table 22: Preferences - Steel Design - Indian IS 800:2007, Part 2 of 2

Table 22: Preferences - Steel Design - Indian IS 800:2007, Part 2 of 2
PlugWeld DLRat SDLAndLLRat LLRat TotalRat NetRat

Yes 120. 120. 360. 240. 240.

12. Design overwrites

This section provides the design overwrites for each type of design, which are assigned to individual
members of the structure.

12.1. Steel design

Page 16 of 28
type 2.sdb SAP2000 v19.2.0 - License #3010*17WPD8FQY83BAK4

Design preferences 07 January 2018

Table 26: Overwrites - Steel Design - Indian IS 800:2007, Part 1 of 5
Table 26: Overwrites - Steel Design - Indian IS 800:2007, Part 1 of 5
Frame DesignSect FrameType Fy RLLF AreaRatio XLMajor XLMinor
KN/m2
10 Program Program 0. 0. 0. 0. 0.
Determined Determined
11 Program Program 0. 0. 0. 0. 0.
Determined Determined
12 Program Program 0. 0. 0. 0. 0.
Determined Determined
14 Program Program 0. 0. 0. 0. 0.
Determined Determined
16 Program Program 0. 0. 0. 0. 0.
Determined Determined

Table 26: Overwrites - Steel Design - Indian IS 800:2007, Part 2 of 5

Table 26: Overwrites - Steel Design - Indian IS 800:2007, Part 2 of 5
Frame XKMajor XKMinor KMajor KMinor C1 kzy kyz Omega

10 0. 0. 0. 0. 0. 0. 0. 0.
11 0. 0. 0. 0. 0. 0. 0. 0.
12 0. 0. 0. 0. 0. 0. 0. 0.
14 0. 0. 0. 0. 0. 0. 0. 0.
16 0. 0. 0. 0. 0. 0. 0. 0.

Table 26: Overwrites - Steel Design - Indian IS 800:2007, Part 3 of 5

Table 26: Overwrites - Steel Design - Indian IS 800:2007, Part 3 of 5
Frame GammaOV Nc Nt Mc3 Mc2 Mb V2 V3
KN KN KN-m KN-m KN-m KN KN
10 0. 0. 0. 0. 0. 0. 0. 0.
11 0. 0. 0. 0. 0. 0. 0. 0.
12 0. 0. 0. 0. 0. 0. 0. 0.
14 0. 0. 0. 0. 0. 0. 0. 0.
16 0. 0. 0. 0. 0. 0. 0. 0.

Table 26: Overwrites - Steel Design - Indian IS 800:2007, Part 4 of 5

Table 26: Overwrites - Steel Design - Indian IS 800:2007, Part 4 of 5
Frame DeflType DLRat SDLAndLLRat LLRat TotalRat NetRat DLAbs
m
10 Program Determined 0. 0. 0. 0. 0. 0.
11 Program Determined 0. 0. 0. 0. 0. 0.
12 Program Determined 0. 0. 0. 0. 0. 0.
14 Program Determined 0. 0. 0. 0. 0. 0.
16 Program Determined 0. 0. 0. 0. 0. 0.

Table 26: Overwrites - Steel Design - Indian IS 800:2007, Part 5 of 5

Table 26: Overwrites - Steel Design - Indian IS 800:2007, Part 5 of 5
Frame SDLAndLLAbs LLAbs TotalAbs NetAbs SpecCambe
r
m m m m m
10 0. 0. 0. 0. 0.
11 0. 0. 0. 0. 0.
12 0. 0. 0. 0. 0.
14 0. 0. 0. 0. 0.
16 0. 0. 0. 0. 0.

Page 17 of 28
type 2.sdb SAP2000 v19.2.0 - License #3010*17WPD8FQY83BAK4

Design preferences 07 January 2018

13. Design summary

This section provides the design summary for each type of design, which highlights the controlling
demand/capacity ratio and it's associated combination and location in each member.

13.1. Steel design

Table 27: Steel Design 1 - Summary Data - Indian IS 800:2007, Part 1 of 2

Table 27: Steel Design 1 - Summary Data - Indian IS 800:2007, Part 1 of 2
Frame Location Combo DesignSect DesignType Ratio RatioType
m
10 0.3 DSTL1 Plate Section Column 0.695008 PMM
11 0.5 DSTL1 Plate Section Beam 0.010584 PMM
12 0. DSTL1 Plate Section Column 0.590557 PMM
14 0.10017 DSTL1 Plate Section Brace 0.69489 PMM
16 0. DSTL1 Plate Section Brace 0.59046 PMM

Table 27: Steel Design 1 - Summary Data - Indian IS 800:2007, Part 2 of 2

Table 27: Steel Design 1 - Summary Data - Indian IS 800:2007, Part 2 of 2
Frame Status ErrMsg WarnMsg

10 See WarnMsg No Messages KL/r > 180 (IS 3.8, Table 3)

11 No Messages No Messages No Messages
12 No Messages No Messages No Messages
14 No Messages No Messages No Messages
16 No Messages No Messages No Messages

Page 18 of 28
type 2.sdb SAP2000 v19.2.0 - License #3010*17WPD8FQY83BAK4

Design preferences 07 January 2018

Design preferences
This section provides the design preferences for each type of design, which typically include material
reduction factors, framing type, stress ratio limit, deflection limits, and other code specific items.

Page 19 of 28
type 2.sdb SAP2000 v19.2.0 - License #3010*17WPD8FQY83BAK4

Design preferences 07 January 2018

Page 20 of 28
type 2.sdb SAP2000 v19.2.0 - License #3010*17WPD8FQY83BAK4

Design preferences 07 January 2018

Page 21 of 28
Indian IS 800:2007 STEEL SECTION CHECK (Summary for Combo and Station)
Units : KN, m, C

Frame : 14 X Mid: 0.049 Combo: DSTL7 Design Type: Brace

Length: 0.100 Y Mid: 0.000 Shape: Plate Section Frame Type: SMF

Loc : 0.100 Z Mid: 0.288 Class: Compact Rolled : No

MultiResponse=Envelopes P-Delta Done? No

GammaM0=1.10 GammaM1=1.25

An/Ag=1.00 RLLF=1.000 PLLF=0.750 D/C Lim=0.950

A=5.000E-04 Izz=0.000 rzz=0.001 Ze,zz=0.000
It=0.000 Iyy=0.000 ryy=0.029 Ze,yy=8.333E-06
Iw=0.000 Iyz=0.000 h=0.005 Zp,zz=0.000 Av,z=4.167E-04

E=199947978.8 fy=250000.000 fu=287500.000 Zp,yy=1.250E-05 Av,y=4.167E-04

Rot= 90 deg Imax=0.000 Imin=0.000 rmax=0.029 rmin=0.001

STRESS CHECK FORCES & MOMENTS Mzz Myy Vy Vz To

Location N 0.000 1.458
0.000 0.000
0.100 0.376 -0.079
PMM DEMAND/CAPACITY RATIO Axial MMajo MMino
Governing Total r r Ratio Status
Equation Ratio Ratio Ratio Ratio + Limit Check
9.3.1.1(az) 0.695 = 0.003 0.950 OK
+ 0.695 0.000
AXIAL FORCE DESIGN N Td Nd Pdy
Force Capacity Pdz Pd
Capacity Capacity
113.636 113.636 Capacity Capacity
Axial 0.376 103.500 76.592 76.592
Tdg Tdn Ncr,T Ncr,TF
371.474 204.867 An/Ag
113.636 103.500 1.000
Curve Alpha fcc Lambda Phi
Major (z-z) c 0.490 409733.459 0.781 0.947
MajorB(z-z) c 0.490 409733.459 Chi fcd
0.781 0.947 0.674 153184.614
Minor (y-y) c 0.490 163893383.5 0.039 0.461
MinorB(y-y) c 0.490 163893383.5 0.674 153184.614
0.039 0.461 1.000 227272.727
0.781 0.947 1.000 227272.727
Torsional TF c 0.490 409733.459
0.674 153184.614
MOMENT DESIGN M Mspan Md(yield) Mdv
Moment Moment Capacity Capacity
Major (z-z) -0.079 -0.079 0.114 0.114 Mnd Md(LTB)
2.273 2.273 Capacity Capacity
Minor (y-y) 0.000 0.000 0.114 0.142
Curve AlphaLT LambdaLT PhiLT ChiLT 2.273
0.455 1.000
LTB c 0.490 0.017
C1 Mcr
Factors Cmy Cmz CmLT Kz 2.828 451.055
1.000 1.000
1.000 1.000
Ky K_LT
SHEAR DESIGN V Vd 1.000 1.000
Stress Status
Force Capacity Ratio Check
Major (y) 1.458 54.673 0.027 OK
0.000 OK To
Minor (z) 0.000 54.673 Torsion
BRACE MAXIMUM AXIAL LOADS 0.000
P P 0.000

Axial Comp Tens

0.000 0.376
Indian IS 800:2007 STEEL SECTION CHECK (Summary for Combo and Station)
Units : N, mm, C

Frame : 10 X Mid: 97.000 Combo: DSTL7 Design Type: Column

Length: 300.000 Y Mid: 0.000 Shape: Plate Section Frame Type: SMF
Loc : 300.000 Z Mid: 150.000 Class: Compact Rolled : No

MultiResponse=Envelopes P-Delta Done? No

GammaM0=1.10 GammaM1=1.25
An/Ag=1.00 RLLF=1.000 PLLF=0.750 D/C Lim=0.950

A=600.000 Izz=1800.000 rzz=1.732 Ze,zz=600.000

It=6927.840 Iyy=500000.000 ryy=28.868 Ze,yy=10000.000
Iw=0.000 Iyz=0.000 h=6.000 Zp,zz=900.000 Av,z=500.000
E=199947.979 fy=250.000 fu=287.500 Zp,yy=15000.000 Av,y=500.000

Rot= 90 deg Imax=500000.000 Imin=1800.000 rmax=28.868 rmin=1.732

STRESS CHECK FORCES & MOMENTS

Location N Mzz Myy Vy Vz To
300.000 -1527.722 -79020.049 0.000 0.000 0.000 0.000

PMM DEMAND/CAPACITY RATIO

Governing Total Axial MMajor MMinor Ratio Status
Equation Ratio Ratio Ratio Ratio Limit Check
9.3.1.1(az) 0.483 = 0.011 + 0.483 + 0.000 0.950 OK

AXIAL FORCE DESIGN

N Td Nd Pdy Pdz Pd
Force Capacity Capacity Capacity Capacity Capacity
Axial -1527.722 124200.000 136363.636 136363.636 27950.265 27950.265

Tdg Tdn Ncr,T Ncr,TF An/Ag

136363.636 124200.000 637033.294 39468.149 1.000

Curve Alpha fcc Lambda Phi Chi fcd

Major (z-z) c 0.490 65.780 1.949 2.829 0.205 46.584
MajorB(z-z) c 0.490 65.780 1.949 2.829 0.205 46.584
Minor (y-y) c 0.490 18272.291 0.117 0.486 1.000 227.273
MinorB(y-y) c 0.490 18272.291 0.117 0.486 1.000 227.273
Torsional TF c 0.490 65.780 1.949 2.829 0.205 46.584

MOMENT DESIGN
M Mspan Md(yield) Mdv Mnd Md(LTB)
Moment Moment Capacity Capacity Capacity Capacity
Major (z-z) -79020.049 -79020.049 163636.364 163636.364 163615.825 204545.455
Minor (y-y) 0.000 0.000 2727272.727 2727272.727 2726930.417

Curve AlphaLT LambdaLT PhiLT ChiLT C1 Mcr

LTB c 0.490 0.049 0.464 1.000 1.000 76426311.2

Factors Cmy Cmz CmLT Kz Ky K_LT

1.000 1.000 1.000 1.044 0.999 1.000

SHEAR DESIGN
V Vd Stress Status To
Force Capacity Ratio Check Torsion
Major (y) 0.000 65607.955 0.000 OK 0.000
Minor (z) 0.000 65607.955 0.000 OK 0.000
Indian IS 800:2007 STEEL SECTION CHECK (Summary for Combo and Station)
Units : KN, m, C

Frame : 12 X Mid: 0.597 Combo: DSTL7 Design Type: Column

Length: 0.040 Y Mid: 0.000 Shape: Plate Section Frame Type: SMF
Loc : 0.000 Z Mid: 0.020 Class: Compact Rolled : No

MultiResponse=Envelopes P-Delta Done? No

GammaM0=1.10 GammaM1=1.25
An/Ag=1.00 RLLF=1.000 PLLF=0.750 D/C Lim=0.950

A=5.000E-04 Izz=0.000 rzz=0.001 Ze,zz=0.000

It=0.000 Iyy=0.000 ryy=0.029 Ze,yy=8.333E-06
Iw=0.000 Iyz=0.000 h=0.005 Zp,zz=0.000 Av,z=4.167E-04
E=199947978.8 fy=250000.000 fu=287500.000 Zp,yy=1.250E-05 Av,y=4.167E-04

Rot= 90 deg Imax=0.000 Imin=0.000 rmax=0.029 rmin=0.001

STRESS CHECK FORCES & MOMENTS

Location N Mzz Myy Vy Vz To
0.000 -1.508 0.067 0.000 0.000 0.000 0.000

PMM DEMAND/CAPACITY RATIO

Governing Total Axial MMajor MMinor Ratio Status
Equation Ratio Ratio Ratio Ratio Limit Check
9.3.1.1(az) 0.591 = 0.013 + 0.591 + 0.000 0.950 OK

AXIAL FORCE DESIGN

N Td Nd Pdy Pdz Pd
Force Capacity Capacity Capacity Capacity Capacity
Axial -1.508 103.500 113.636 113.636 107.166 90.582

Tdg Tdn Ncr,T Ncr,TF An/Ag

113.636 103.500 371.474 371.474 1.000

Curve Alpha fcc Lambda Phi Chi fcd

Major (z-z) c 0.490 2569540.952 0.312 0.576 0.943 214331.280
MajorB(z-z) c 0.490 2569540.952 0.312 0.576 0.943 214331.280
Minor (y-y) c 0.490 1027816381 0.016 0.455 1.000 227272.727
MinorB(y-y) c 0.490 1027816381 0.016 0.455 1.000 227272.727
Torsional TF c 0.490 742948.861 0.580 0.761 0.797 181164.891

MOMENT DESIGN
M Mspan Md(yield) Mdv Mnd Md(LTB)
Moment Moment Capacity Capacity Capacity Capacity
Major (z-z) 0.067 0.067 0.114 0.114 0.114 0.142
Minor (y-y) 0.000 0.000 2.273 2.273 2.272

Curve AlphaLT LambdaLT PhiLT ChiLT C1 Mcr

LTB c 0.490 0.018 0.455 1.000 1.000 399.355

Factors Cmy Cmz CmLT Kz Ky K_LT

1.000 1.000 1.000 1.002 0.998 1.000

SHEAR DESIGN
V Vd Stress Status To
Force Capacity Ratio Check Torsion
Major (y) 0.000 54.673 0.000 OK 0.000
Minor (z) 0.000 54.673 0.000 OK 0.000
 Result:-
Provide Steel Plate Section as per the Drawing Provided with Thickness of 6mm.

Design Parameters

Diameter of the bolt d 6mm

Nominal diameter of bolt do 8mm

Thickness of plate t 2.40mm

Minimum Pitch distance Pmin 15mm

(IS 800
Cl10.2.2)
Minimum Edge distance emin 12mm(IS800,
Cl10.2.4.2)
Maximum Pitch distance Pmax 77mm(IS
800,Cl10.2.3.1)
Maximum Edge distance emax 47mm
(IS 800
Cl10.2.4.3)
Ultimate tensile strength of a bolt fub 195N/mm2

156N/mm2 (0.8
Yield stress of the bolt fyb
fub)

Ultimate tensile strength of a plate fu 195N/mm2

Number of shear planes with threads intercepting the 1

nn
shear plane

Number of shear planes without threads intercepting the

ns 0
shear plane

Number of bolts provided nb 1

Partial safety factor for bolted connection with bearing

ᵞmb 1.25
type bolts

Partial safety factor against yield stress and buckling ᵞmo 1.1

Nominal plain shank area of the bolt Asb 28.27mm2

Net shear area of the bolt at threads Anb 22.62mm2
Design of Connection Bolt
Shear Capacity of Bolt

Nominal shear capacity of

Vnsb 2.55kN
the bolt

Design strength of the bolt Vdsb 2.04kN

Bearing Capacity of Bolt
Reduction factor Kb 0.375
Nominal bearing capacity of a bolt Vnpb 2.63kN
Design bearing capacity of a bolt Vdpb 2.10kN
NOTE: The design strength of the bolt shall be taken as the smaller of the value as governed by shear
(Vdsb) and bearing (Vdpb).
Bolt capacity Vdb 2.04kN
Tension Capacity Design tension capacity of bolt Tdb 3.97kN
Total tensile force in the bolt Tb 4.45kN
2

Shear stress= τ 112.50N/mm

Tensile yield stress or σt 195N/mm2

design stress

Pitch diameter Dp
Axial length of full thread L 0.00159mm
engagement
Safety factor S 1.8
Pull-out Force F 2.50kN
Reaction at Purlins where bolt connects 1.21kN
Pull-out Force Calculation
Pull out force of bolt should always be greater than reaction at purlin where bolt connects. Hence safe.