SN55114, SN75114

DUAL DIFFERENTIAL LINE DRIVERS

SLLS071C – SEPTEMBER 1973 – REVISED SEPTEMBER 1998

D Choice of Open-Collector, Open-Emitter, or SN55114 . . . J OR W PACKAGE

Totem-Pole Outputs SN75114 . . . D OR N PACKAGE
(TOP VIEW)
D Single-Ended or Differential AND/NAND
Outputs
1ZP 1 16 VCC
D Single 5-V Supply 1ZS 2 15 2ZP
D Dual-Channel Operation 1YS 3 14 2ZS
D TTL Compatible 1YP 4 13 2YS
D Short-Circuit Protection 1A 5
6
12
11
2YP
1B 2C
D High-Current Outputs
1C 7 10 2B
D Triple inputs GND 8 9 2A
D Clamp Diodes at Inputs and Outputs
D Designed for Use With SN55115 and SN55114 . . . FK PACKAGE
SN75115 Differential Line Receivers (TOP VIEW)
D Designed to Be Interchangeable With

VCC
1ZS
1ZP

2ZP
NC
National DS9614 Line Driver

description 3 2 1 20 19
1YS 4 18 2ZS
The SN55114 and SN75114 dual differential line 1YP 5 17 2YS
drivers are designed to provide differential output NC 6 16 NC
signals with the high-current capability for driving 1A 7 15 2YP
balanced lines, such as twisted pair, at normal line 1B 8 14 2C
9 10 11 12 13
impedances without high power dissipation. The
output stages are similar to TTL totem-pole

2A
2B
1C

NC
GND
outputs, but with the sink outputs, YS and ZS, and
the corresponding active pullup terminals, YP and NC – No internal connection
ZP, available on adjacent package pins. Since the
output stages provide TTL-compatible output
levels, these devices can also be used as TTL
expanders or phase splitters.
The SN55114 is characterized for operation over the full military temperature range of – 55°C to 125°C. The
SN75114 is characterized for operation from 0°C to 70°C.

FUNCTION TABLE
INPUTS OUTPUTS
A B C Y Z
H H H H L
All other input combinations L H
H = high level, L = low level

Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

PRODUCTION DATA information is current as of publication date. Copyright  1998, Texas Instruments Incorporated
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1

SN55114, SN75114
DUAL DIFFERENTIAL LINE DRIVERS
SLLS071C – SEPTEMBER 1973 – REVISED SEPTEMBER 1998

logic symbol† logic diagram (positive logic)

4
1YP
& 4 5 3
5 1YP 1A 1YS
1A 3 6
6 1YS 1B 1
1B 1 7 1ZP
7 1ZP 1C 2
1C 2 1ZS
1ZS
12 12
9 2YP 2YP
2A 13 9 13
10 2YS 2A 2YS
2B 15 10
11 2ZP 2B 15
2C 14 11 2ZP
2ZS 2C 14
2ZS
† This symbol is in accordance with ANSI/IEEE Std 91-1984 and
IEC Publication 617-12.
Pin numbers shown are for the D, J, N, and W packages.

schematic (each driver)

To
Inputs
Other Driver
C B A
7,11 5,9 16

6, 600‡ 1k VCC
1k 4k
10

‡
600 600

‡ 4k
9 4k 9
900 900 1, 15 NAND Pullup
AND 4, 12
Pullup ZP
90
YP 3, 13 90 2, 14 NAND
‡ 5k
AND 5k Sink Output
Sink Output ZS
‡
YS 500
500 333 8
GND

‡ These components are common to both drivers. Resistor values shown are nominal and in ohms.
Pin numbers shown are for the D, J, N, and W packages.

2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

 SN55114, SN75114
DUAL DIFFERENTIAL LINE DRIVERS
SLLS071C – SEPTEMBER 1973 – REVISED SEPTEMBER 1998

absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Input voltage, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
Off-state voltage applied to open-collector outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 V
Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C
Case temperature for 60 seconds, Tc: FK package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds: J or W package . . . . . . . . . . . . . . . . 300°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: D or N package . . . . . . . . . . . . . . . . 260°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values are with respect to the network ground terminal.

DISSIPATION RATING TABLE

TA ≤ 25°C DERATING FACTOR TA = 70°C TA = 125°C
PACKAGE
POWER RATING ABOVE TA = 25°C POWER RATING POWER RATING
D 950 mW 7.6 mW/°C 608 mW —
FK‡ 1375 mW 11.0 mW/°C 880 mW 275 mW
J‡ 1375 mW 11.0 mW/°C 880 mW 275 mW
N 1150 mW 9.2 mW/°C 736 mW —
W‡ 1000 mW 8.0 mW/°C 640 mW 200 mW
‡ In the FK, J, and W packages, SN55114 chips are either silver glass or alloy mounted.

recommended operating conditions (unless otherwise noted)

SN55114 SN75114
UNIT
MIN NOM MAX MIN NOM MAX
Supply voltage, VCC 4.5 5 5.5 4.75 5 5.25 V
High-level input voltage, VIH 2 2 V
Low-level input voltage, VIL 0.8 0.8 V
High-level output current, IOH – 40 – 40 mA
Low-level output current, IOL 40 40 mA
Operating free-air temperature, TA – 55 125 0 70 °C

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3

SN55114, SN75114
DUAL DIFFERENTIAL LINE DRIVERS
SLLS071C – SEPTEMBER 1973 – REVISED SEPTEMBER 1998

electrical characteristics over recommended operating free-air temperature range (unless

otherwise noted)
SN55114 SN75114
PARAMETER TEST CONDITIONS† UNIT
MIN TYP‡ MAX MIN TYP‡ MAX
VIK Input clamp voltage VCC = MIN, II = – 12 mA –0.9 –1.5 –0.9 –1.5 V
High-level
g output VCC = MIN,, VIH = 2 V,, IOH = –10 mA 2.4 3.4 2.4 3.4
VOH V
voltage VIL = 0.8 V IOH = – 40 mA 2 3 2 3
Low-level output VCC = MIN,, VIH = 2 V,,
VOL 02
0.2 04
0.4 02
0.2 0 45
0.45 V
voltage VIL = 0.8 V, IOL = 40 mA
VCC = 5 V, IO = 40 mA, TA = 25°C 6.1 6.5 6.1 6.5
VOK Output clamp voltage V
VCC = MAX, IO = – 40 mA, TA = 25°C –1.1 –1.5 –1.1 –1.5
TA = 25°C 1 100
VOH = 12 V
Off-state open collector TA = 125°C 200
IO( ff)
O(off) VCC = MAX µA
output current TA = 25°C 1 100
VOH = 5
5.25
25 V
TA = 70°C 200
Input current at
II VCC = MAX
MAX, VI = 5 5V
5.5 1 1 mA
maximum input voltage
IIH High-level input current VCC = MAX, VI = 2.4 V 40 40 µA
IIL Low-level input current VCC = MAX, VI = 0.4 V –1.1 –1.6 –1.1 –1.6 mA
Short-circuit
IOS VCC = MAX
MAX, VO = 0
0, TA = 25°C –40
40 –90
90 –120
120 –40
40 –90
90 –120
120 mA
output current§
Supplyy current All inputs at 0 V, No load, VCC = MAX 37 50 37 50
ICC mA
(both drivers) TA = 25°C VCC = 7 V 47 65 47 70
† All parameters, with the exception of off-state open-collector output current, are measured with the active pullup connected to the sink output.
For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions.
‡ All typical values are at TA = 25°C and VCC = 5 V, with the exception of ICC at 7 V.
§ Only one output should be shorted at a time, and duration of the short circuit should not exceed one second.

switching characteristics, VCC = 5 V, TA = 25°C

TEST SN55114 SN75114
PARAMETER UNIT
CONDITIONS MIN TYP MAX MIN TYP MAX
tPLH Propagation delay time, low- to high-level output CL = 30 pF, 15 20 15 30 ns
tPHL Propagation delay time, high- to low-level output See Figure 1 11 20 11 30 ns

4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

 SN55114, SN75114
DUAL DIFFERENTIAL LINE DRIVERS
SLLS071C – SEPTEMBER 1973 – REVISED SEPTEMBER 1998

PARAMETER MEASUREMENT INFORMATION

≤ 5 ns ≤ 5 ns

3V
Input VCC = 5 V 90% 90%
1.5 V 1.5 V

ÁÁ
10% 10%
Input tw 0V
2 kΩ

ÁÁ Y

ÁÁ
AND Output tPLH tPHL
VOH

ÁÁ
CL = 30 pF
Pulse Y
Generator (see Note B) 1.5 V 1.5 V
Output

ÁÁ
(see Note A) Z
VOL
NAND Output
50 Ω
CL = 30 pF VOH
tPLH
(see Note B)
Z
Output 1.5 V 1.5 V
TEST CIRCUIT
tPHL VOL
VOLTAGE WAVEFORMS
NOTES: A. The pulse generator has the following characteristics: ZO = 500 Ω, PRR ≤ 500 kHz, tw ≤ 100 ns.
B. CL includes probe and jig capacitance.

Figure 1. Test Circuit and Voltage Waveforms

TYPICAL CHARACTERISTICS†

OUTPUT VOLTAGE OUTPUT VOLTAGE

vs vs

ÎÎÎÎ
ÁÁÁÁ ÎÎÎÎÎ
ÁÁÁÁ
DATA INPUT VOLTAGE DATA INPUT VOLTAGE

ÎÎÎÎ
ÁÁÁÁ ÎÎÎÎ
ÁÁÁÁ
ÎÎÎÎÎ
6 6
No Load VCC = 5 V

ÁÁÁÁ ÎÎÎÎ
ÁÁÁÁ ÎÎÎÎÎ
TA = 25°C No Load

ÎÎÎÎ
5 5

ÎÎÎÎ
TA = 125°C
VO – Output Voltage – V
VO – Output Voltage – V

VCC = 5.5 V

ÎÎÎÎ
4 4
VCC = 5 V

ÎÎÎÎ
VCC = 4.5 V
ÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎ
3 3
TA = 25°C

ÁÁ
ÁÁ
2
ÁÁ
ÁÁ ÎÎÎÎÎ 2
TA = – 55°C
VO
VO

1 1

0 0
0 1 2 3 4 0 1 2 3 4
VI – Data Input Voltage – V VI – Data Input Voltage – V

Figure 2 Figure 3

† Operation of the device at these or any other conditions beyond those indicated under ”recommended operating conditions” is not implied. These
parameters were measured with the active pullup connected to the sink output.

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5

SN55114, SN75114
DUAL DIFFERENTIAL LINE DRIVERS
SLLS071C – SEPTEMBER 1973 – REVISED SEPTEMBER 1998

TYPICAL CHARACTERISTICS†

HIGH-LEVEL OUTPUT VOLTAGE LOW-LEVEL OUTPUT VOLTAGE

vs vs

ÎÎÎÎÎ ÎÎÎÎÎ
HIGH-LEVEL OUTPUT CURRENT LOW-LEVEL OUTPUT CURRENT
5 0.4

ÎÎÎÎ
ÎÎÎÎÎ
ÎÎÎÎ
TA = 25°C
ÎÎÎÎÎ ÎÎÎÎÎ
TA = 25°C
VOH – High-Level Output Voltage – V

VCC = 5.5 V

VOL – Low-Level Output Voltage – V

ÎÎÎÎÎ ÎÎÎÎÎ
4 VCC = 5.5 V

ÎÎÎÎÎ
VCC = 5 V 0.3

0.2
ÎÎÎÎÎ VCC = 4.5 V

ÎÎÎÎ
2

ÁÁÁ ÁÁ
VCC = 4.5 V

ÁÁÁ ÁÁ
0.1
1

ÁÁÁÁ ÁÁ
Á
0 0
0 – 20 – 40 – 60 – 80 – 100 – 120 0 10 20 30 40 50 60 70 80

IOH – High-Level Output Current – mA IOL – Low-Level Output Current – mA

Figure 4 Figure 5

OUTPUT VOLTAGE PROPAGATION DELAY TIMES

vs vs
FREE-AIR TEMPERATURE FREE-AIR TEMPERATURE

ÎÎÎÎÎ
ÎÎÎÎÎ
4

3.6
VCC = 4.5 V
40
ÁÁÁÁÁ
ÁÁÁÁÁ
VCC = 5 V

ÎÎÎÎÎÎ
See Figure 1
Propagation Delay Times – ns

ÎÎÎÎÎÎ
3.2
VOH(IOH = – 10 mA) 30
VO – Output Voltage – V

2.8

ÎÎÎÎÎÎÎ 2.4

2
VOH(IOH = – 40 mA)
20
ÎÎÎ
ÁÁÁ
1.6
ÎÎÎ
tPLH

ÁÁÁ ÎÎÎÎÎ ÎÎÎ

VO

1.2
10
0.8 tPHL

ÎÎÎÎÎ 0.4 VOL(IOL = 40 mA)

0 0
– 75 – 50 – 25 0 25 50 75 100 125 – 75 – 50 – 25 0 25 50 75 100 125

TA – Free-Air Temperature – °C TA – Free-Air Temperature – °C

Figure 6 Figure 7

† Operation of the device at these or any other conditions beyond those indicated under ”recommended operating conditions” is not implied. These
parameters were measured with the active pullup connected to the sink output.

6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

 SN55114, SN75114
DUAL DIFFERENTIAL LINE DRIVERS
SLLS071C – SEPTEMBER 1973 – REVISED SEPTEMBER 1998

TYPICAL CHARACTERISTICS†

SUPPLY CURRENT
SUPPLY CURRENT
(BOTH DRIVERS)
(BOTH DRIVERS)
vs
vs
SUPPLY VOLTAGE

ÎÎÎÎ
ÁÁÁÁ ÁÁÁÁÁÁ
FREE-AIR TEMPERATURE
80

ÎÎÎÎ
ÁÁÁÁ ÁÁÁÁÁÁ
No Load 42
VCC = 5 V

ÁÁÁÁ ÁÁÁÁÁÁ
TA = 25°C
70 Inputs Grounded

ÁÁÁÁÁÁ
40 Outputs Open
60
I CC – Supply Current – mA

I CC – Supply Current – mA
ÎÎÎÎÎÎ
50 38
Inputs Grounded

ÎÎÎÎÎ ÁÁÁ
40
36

ÁÁ ÎÎÎÎÎ 30 Inputs Open

ÁÁ ÁÁÁ
34
ICC

ICC
ÁÁ ÁÁÁ
20

10 32

0
0 1 2 3 4 5 6 7 8 30
– 75 – 50 – 25 0 25 50 75 100 125
VCC – Supply Voltage – V TA – Free-Air Temperature – °C
Figure 8 Figure 9
SUPPLY CURRENT
(BOTH DRIVERS)
vs
FREQUENCY
100
ÁÁÁÁ
ÁÁÁÁ
VCC = 5 V

ÁÁÁÁÁÁÁ
ÁÁÁÁ
RL = ∞

ÁÁÁÁÁÁÁ
ÁÁÁÁ
80 CL = 30 pF
I CC – Supply Current – mA

Inputs: 3-V Square Wave

ÁÁÁÁ
TA = 25°C

60

ÁÁÁ
40

ÁÁÁ
ICC

20

0
0.1 0.4 1 4 10 40 100
f – Frequency – MHz

Figure 10
† Operation of the device at these or any other conditions beyond those indicated under ”recommended operating conditions” is not implied. These
parameters were measured with the active pullup connected to the sink output.

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 7

SN55114, SN75114
DUAL DIFFERENTIAL LINE DRIVERS
SLLS071C – SEPTEMBER 1973 – REVISED SEPTEMBER 1998

APPLICATION INFORMATION
1/2 SN75114 1/2 SN75115
Driver Receiver

RT† RT†

Twisted Pair
† RT = ZO. A capacitor can be connected in series with RT to reduce power dissipation.

Figure 11. Basic Party-Line or Data-Bus Differential Data Transmission

8 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

 IMPORTANT NOTICE

Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.

TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.

CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF

DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL
APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR
WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO
BE FULLY AT THE CUSTOMER’S RISK.

In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.

TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.

Copyright  1998, Texas Instruments Incorporated

This datasheet has been download from:

www.datasheetcatalog.com

Datasheets for electronics components.

 Texas Instruments
http://www.ti.com

This file is the datasheet for the following electronic components:

SN75114 - http://www.ti.com/product/sn75114?HQS=TI-null-null-dscatalog-df-pf-null-wwe