Scribd Logo
Upload

Welcome to Scribd!

  • 53 views

    Accelerator Control System: Section

    Uploaded by

    Tony
    The document provides instructions for removing and installing the accelerator control system on a 2006 Murano. Key steps include: 1. Moving the accelerator and brake pedals fully forward and disconnecting the negative battery terminal before removal. 2. Disconnecting the accelerator pedal position sensor harness and drive cable (for adjustable pedals). 3. Loosening mounting nuts to remove the accelerator pedal assembly in one piece. 4. Inspecting pedal movement and return function after installation. Learning the pedal's released position using the ECU if the sensor was disconnected.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Accelerator Control System: Section

    Uploaded by

    Tony
    53 views4 pages
    The document provides instructions for removing and installing the accelerator control system on a 2006 Murano. Key steps include: 1. Moving the accelerator and brake pedals fully forward and disconnecting the negative battery terminal before removal. 2. Disconnecting the accelerator pedal position sensor harness and drive cable (for adjustable pedals). 3. Loosening mounting nuts to remove the accelerator pedal assembly in one piece. 4. Inspecting pedal movement and return function after installation. Learning the pedal's released position using the ECU if the sensor was disconnected.

    Original Description:

    Nissan Murano 2006

    Original Title

    Acc

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides instructions for removing and installing the accelerator control system on a 2006 Murano. Key steps include: 1. Moving the accelerator and brake pedals fully forward and disconnecting the negative battery terminal before removal. 2. Disconnecting the accelerator pedal position sensor harness and drive cable (for adjustable pedals). 3. Loosening mounting nuts to remove the accelerator pedal assembly in one piece. 4. Inspecting pedal movement and return function after installation. Learning the pedal's released position using the ECU if the sensor was disconnected.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    53 views4 pages

    Accelerator Control System: Section

    Uploaded by

    Tony
    The document provides instructions for removing and installing the accelerator control system on a 2006 Murano. Key steps include: 1. Moving the accelerator and brake pedals fully forward and disconnecting the negative battery terminal before removal. 2. Disconnecting the accelerator pedal position sensor harness and drive cable (for adjustable pedals). 3. Loosening mounting nuts to remove the accelerator pedal assembly in one piece. 4. Inspecting pedal movement and return function after installation. Learning the pedal's released position using the ECU if the sensor was disconnected.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 4

    ACCELERATOR CONTROL SYSTEM

    B ENGINE

    ACCELERATOR CONTROL SYSTEM


    SECTION ACC ACC

    E
    CONTENTS
    PRECAUTIONS .......................................................... 2 ACCELERATOR CONTROL SYSTEM ....................... 3 F
    Precautions for Supplemental Restraint System Removal and Installation .......................................... 3
    (SRS) “AIR BAG” and “SEAT BELT PRE-TEN- REMOVAL ............................................................. 3
    SIONER” .................................................................. 2 INSTALLATION ..................................................... 3 G
    INSPECTION AFTER INSTALLATION .................. 4

    Revision: 2005 September ACC-1 2006 Murano


    PRECAUTIONS

    PRECAUTIONS PFP:00001

    Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
    BELT PRE-TENSIONER” NBS002RW

    The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
    with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
    types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
    system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
    air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
    Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
    ual.
    WARNING:
    ● To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
    in the event of a collision which would result in air bag inflation, all maintenance must be per-
    formed by an authorized NISSAN/INFINITI dealer.
    ● Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
    sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
    Bag Module, see the SRS section.
    ● Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
    Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
    harness connectors.

    Revision: 2005 September ACC-2 2006 Murano


    ACCELERATOR CONTROL SYSTEM

    ACCELERATOR CONTROL SYSTEM PFP:18005


    A
    Removal and Installation NBS002RX

    ACC

    G
    PBIC4205E

    1. Accelerator pedal assembly

    REMOVAL H
    1. Move accelerator and brake pedals to the front most position (Adjustable type).
    2. Turn ignition switch “OFF” and disconnect negative battery terminal.
    3. Disconnect accelerator pedal position sensor harness connector. I
    4. Disconnect drive cable from accelerator pedal assembly (Adjustable type).
    ● Unlock (1) then pull (2) to disconnect drive cable.
    J

    SBIA0382E
    M
    5. Loosen nuts, and remove accelerator pedal assembly.
    CAUTION:
    ● Before removal and installation accelerator and brake pedals must be in front most position.
    This is to align the base position of accelerator and brake pedals (Adjustable type).
    ● Do not disassemble accelerator pedal assembly. Do not remove accelerator pedal position sen-
    sor from accelerator pedal assembly.
    ● Adjusting mechanism for accelerator pedal position is not able to disassemble (Adjustable
    type).
    ● Avoid impact from dropping etc. during handling.

    ● Be careful to keep accelerator pedal assembly away from water.

    NOTE:
    Drive cable of the adjustable type accelerator pedal assembly is a component of brake pedal. Refer to
    BR-6, "BRAKE PEDAL" .
    INSTALLATION
    Install in the reverse order of removal.

    Revision: 2005 September ACC-3 2006 Murano


    ACCELERATOR CONTROL SYSTEM

    INSPECTION AFTER INSTALLATION


    ● Make sure accelerator pedal moves smoothly within the whole operation range when it is fully depressed
    and released.
    ● Make sure accelerator pedal securely returns to the fully released position.
    ● Check operation conditions in forward and rearward movement of accelerator pedal assembly (Adjustable
    type). Refer to BR-6, "BRAKE PEDAL" .
    ● For the electrical inspection of accelerator pedal position sensor, refer to EC-571, "DTC P2122, P2123
    APP SENSOR" , EC-577, "DTC P2127, P2128 APP SENSOR" and EC-591, "DTC P2138 APP SENSOR"
    .
    CAUTION:
    When harness connector of accelerator pedal position sensor is disconnected, perform “Acceler-
    ator Pedal Released Position Learning”. Refer to EC-75, "Accelerator Pedal Released Position
    Learning" .

    Revision: 2005 September ACC-4 2006 Murano

    You might also like