Scribd
Upload
135 views

Syrus3GQuickProgrammingGuide-v1 3

This document provides instructions for programming Syrus 3G devices. It includes: 1. An overview of what is included in the packaging and the necessary hardware for programming, including the Syrus 3G devices, programming box, cables and screws. 2. Step-by-step instructions for connecting the Syrus 3G to the programming box using the proper cables. 3. Instructions for installing the driver software and using the SyrusDesk program to communicate with the device, program the network settings, and check the firmware version once programming is complete.

Uploaded by

LOGIRASTREO SAS
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
135 views

Syrus3GQuickProgrammingGuide-v1 3

This document provides instructions for programming Syrus 3G devices. It includes: 1. An overview of what is included in the packaging and the necessary hardware for programming, including the Syrus 3G devices, programming box, cables and screws. 2. Step-by-step instructions for connecting the Syrus 3G to the programming box using the proper cables. 3. Instructions for installing the driver software and using the SyrusDesk program to communicate with the device, program the network settings, and check the firmware version once programming is complete.

Uploaded by

LOGIRASTREO SAS
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 7

QUICK PROGRAMMING GUIDE

Packing - Device - Programming


PINOUT

PACKING - WHAT’S INCLUDED:


● 1 box with 20 Syrus 3G’s
● *Separate box will be received for the ​Developer Programming Box with Power Adapter and USB data cable
● 84 screws (4 extra screws included)

Version 1.3 - Page 1

5835 Blue Lagoon Dr. # 202 Miami FL, 33129


+1 305 809 0638
www.digitalcomtech.com
INSTALLATION PROCEDURES - DEVICES
Step 1:
● Identify Syrus 3G and the ​Developer Programming Box.

Step 2:
In order to program the Syrus 3G, you need to connect the following cables:
● Ground (GND), Power (VCC), TX and RX

On the Developer Programming Box, push down with a flat-head screw driver the top of the connector to
open it and then insert the proper cable into its specific connector as shown below:

The cables should look like this once inserted to start programming:

Version 1.3 - Page 2

5835 Blue Lagoon Dr. # 202 Miami FL, 33129


+1 305 809 0638
www.digitalcomtech.com
The following steps are for upgrading the devices firmware.
If you are a Pegasus Gateway User you do not need to follow these steps since the firmware is
automatically upgraded, you may proceed to use your Pegasus Gateway script configurator

PROGRAMMING PROCEDURES – SOFTWARE


Step 3:
1. Connect the USB Mini B data cable from programming box to the computer
2. Connect Power adapter to the Programming box

On your PC you should see a Driver Software Installation window.

If your PC fails to recognize the drivers, please visit the following ​page​ for instructions.

Open up the SyrusDesk Program - ​Click here​ to download


Click the button to scan for ports

Version 1.3 - Page 3

5835 Blue Lagoon Dr. # 202 Miami FL, 33129


+1 305 809 0638
www.digitalcomtech.com
Device found, click the 15 digit number tab along the top

Write the following command in the white line and press send to test communication
>QVR<
You should see a response in the console window with something similar to :
>RVR;__S3 Firmware__;ID=__IMEI__<

Version 1.3 - Page 4

5835 Blue Lagoon Dr. # 202 Miami FL, 33129


+1 305 809 0638
www.digitalcomtech.com
Program the Network Settings - APN, Username, Password
Replace the letters in red with your SIM Card provider’s information (Login/Password Optional)

>SRFA​apn​<
>SRFL​login​<
>SRFP​password​<

Example: ​>SRFAinternetd.gdsp<

Wait about 5 minutes.

Once the device has a valid IP address

you should see something similar to this in the console window.

Version 1.3 - Page 5

5835 Blue Lagoon Dr. # 202 Miami FL, 33129


+1 305 809 0638
www.digitalcomtech.com
The procedure is finished when your device shows the
>RXART;3.1.27;ID=__IMEI #__<

QUESTIONS?
support@digitalcomtech.com

- END

Version 1.3 - Page 6

5835 Blue Lagoon Dr. # 202 Miami FL, 33129


+1 305 809 0638
www.digitalcomtech.com

You might also like