Scribd
Upload
391 views3 pages

Reactance Relay Properties

The reactance relay is a high-speed relay that consists of an overcurrent element and a current-voltage directional element. It is an overcurrent relay with directional limitation where the directional element develops maximum negative torque when the current lags behind the voltage by 90 degrees. A typical reactance relay uses an induction cup structure with four poles carrying operating, polarizing, and restraining coils. The operating torque is proportional to the square of the current while the restraining torque is proportional to the voltage times the cosine of the phase angle minus 90 degrees. The operating characteristic of a reactance relay shows that the resistance component of the impedance has no effect on the relay, which reacts solely to the reactance component

Uploaded by

Tanveer Ul Haq
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
391 views3 pages

Reactance Relay Properties

The reactance relay is a high-speed relay that consists of an overcurrent element and a current-voltage directional element. It is an overcurrent relay with directional limitation where the directional element develops maximum negative torque when the current lags behind the voltage by 90 degrees. A typical reactance relay uses an induction cup structure with four poles carrying operating, polarizing, and restraining coils. The operating torque is proportional to the square of the current while the restraining torque is proportional to the voltage times the cosine of the phase angle minus 90 degrees. The operating characteristic of a reactance relay shows that the resistance component of the impedance has no effect on the relay, which reacts solely to the reactance component

Uploaded by

Tanveer Ul Haq
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

Reactance Relay

The reactance relay is a high-speed relay. This relay consists of two elements an overcurrent
element and a current-voltage directional element. The current element developed positive torque
and a current-voltage developed directional element which opposes the current element
depending on the phase angle between current and voltage.

Reactance relay is an overcurrent relay with directional limitation. The directional element is
arranged to develop maximum negative torque when its current lag behinds its voltage by 90°.
The induction cup or double induction loop structures are best suited for actuating reactance type
distance relays.

Construction of Reactance Relay


A typical reactance relay using the induction cup structure is shown in the figure below. It has a
four-pole structure carrying operating, polarizing, and restraining coils, as shown in the figure
below. The operating torque is developed by the interaction of fluxes due to current carrying
coils, i.e., the interaction of fluxes of 2, 3 and 4 and the restraining torque is produced by the
interaction of fluxes due to poles 1, 2 and 4.

The operating torque will be proportional to the


square of the current while the restraining torque will be proportional to VI cos (Θ – 90°). The
desired maximum torque angle is obtained with the help of resistance-capacitance circuits, as
illustrated in the figure. If the control effect is indicated by –k3, the torque equation becomes
where Θ, is defined as positive when I lag
behind V. At the balance point net torque is zero, and hence

The spring control effect


is neglected in the above equation, i.e., K3 = 0.

Operating Characteristic of Reactance Relay


The operating characteristic of a reactance relay is shown in the figure below. X is the reactance
of the protected line between the relay location and the fault point, and R is the resistance
component of the impedance. The characteristic shows that the resistance component of the
impedance has no consequence on the working of the relay, the relay reacts solely to the
reactance component. The point below the operating characteristic is called the positive torque
region.
If the value of τ, in the general
torque equation, expressed below is made any other 90º, a straight line characteristic will still be
obtained, but it will not be parallel to R-axis. Such a relay is called an angle impedance relay.

This type of relay is not capable of selecting


whether the fault has taken place in the section where the relay is located, or it has taken place in
the adjoining section when used on the transmission line. The directional unit used with the
reactance relay will not be same as used with the impedance type relay because the restraining
reactive volt-ampere, in that case, will be nearly equal to zero.

Therefore the reactance type distance relay needs a directional unit that is inoperative under load
conditions. Reactance type relay is very suitable as a ground relay for ground fault because its
reach is not affected by fault impedance.

You might also like