Quincy QSI Series: Instruction Manual

Quincy
®
QSI Series
Instruction Manual
This manual contains important safety

information and should be made available
to all personnel who operate and/or
maintain this product. Carefully read this
manual before attempting to operate or
perform maintenance on this compressor.
Quincy
®
Compressor
True Blue ReliabilitySM
Manual No. 65005-CB April 2001 Edition

Table of Contents
Section I - General
Standard Warranty ...................................................................................................................................................... 1
Safety Alert Symbols ................................................................................................................................................. 2
Safety Precautions ...................................................................................................................................................... 3
Spare Parts Ordering Information .............................................................................................................................. 4
Serial/Model Identification Plate ............................................................................................................................... 4
Model Identification ................................................................................................................................................... 5
Section II - Description
General Description .................................................................................................................................................... 6
The Compression Cycle ............................................................................................................................................. 6
Air Flow ..................................................................................................................................................................... 7
Cooling System .......................................................................................................................................................... 7
Capacity Control System ......................................................................................................................................... 8-9
Electrical System ...................................................................................................................................................... 10
Indicators .................................................................................................................................................................. 11
Gauges ...................................................................................................................................................................... 11
Section III - Installation
Receiving .................................................................................................................................................................. 12
Moving the Unit to the Installation Site ................................................................................................................... 12
Location .................................................................................................................................................................... 13
Piping Connections .................................................................................................................................................. 13
Relief Valves ............................................................................................................................................................ 14
Electrical ................................................................................................................................................................... 14
Guards ...................................................................................................................................................................... 14
Manual Vent and Shutoff Valves ............................................................................................................................. 15
Water and Sewer Facilities at the Installation Site ................................................................................................... 15
Compressor Rotation ................................................................................................................................................ 15
Fan Rotation ............................................................................................................................................................. 15
Section IV - Operating Procedures
Prior To Starting ....................................................................................................................................................... 16
Starting the Compressor ........................................................................................................................................... 16
Stopping the Compressor - Normal Operation......................................................................................................... 17
Stopping the Compressor - Emergency Operation .................................................................................................. 17
Section V - Maintenance or Service Preparation
Maintenance or Service Preparation ........................................................................................................................ 18
Section VI - Servicing
Safety ........................................................................................................................................................................ 20
Water Removal ......................................................................................................................................................... 20
Air/Fluid Separator Element .............................................................................................................................. 20-21
Fluid Scavenging System ......................................................................................................................................... 22
Quincy Compressor-QSI®
Table of Contents
Section VI - Servicing (continued)

Control Line Air Filter ............................................................................................................................................. 22
Shaft Seal ............................................................................................................................................................ 23-24
Air and Fluid Tubing ................................................................................................................................................ 24
O-ring Fittings .......................................................................................................................................................... 25
Section VII - Compressor Fluids
Fluid Specifications .................................................................................................................................................. 26
Lubrication ............................................................................................................................................................... 27
Fluid Level ............................................................................................................................................................... 27
Fluid Sample Valve .................................................................................................................................................. 28
Fluid Filter ................................................................................................................................................................ 28
Factors Affecting Fluid Life ..................................................................................................................................... 29
Fluid Analysis Program - General ............................................................................................................................ 29
QuinSyn PG .............................................................................................................................................................. 30
QuinSyn XP .............................................................................................................................................................. 31
QuinSyn Plus ............................................................................................................................................................ 32
QuinSyn Fluids ......................................................................................................................................................... 33
QuinSyn Flush (changed 02/04) ............................................................................................................................. 34
Cleaning and Flushing With QuinSyn Flush ............................................................................................................ 35
Converting to QuinSyn PG ....................................................................................................................................... 36
Converting to QuinSyn XP ....................................................................................................................................... 37
Converting to QuinSyn Plus ..................................................................................................................................... 37
Converting to QuinSyn ............................................................................................................................................. 38
Sampling Procedures ................................................................................................................................................ 39
Analysis Report (sample) ......................................................................................................................................... 40
Understanding the Analysis Report ......................................................................................................................... 41
Fluid Parameters ................................................................................................................................................... 42-43
Section VIII - Service Adjustments
Differential Pilot Valve ............................................................................................................................................ 44
Pressure Switch ........................................................................................................................................................ 44
Water Temperature Regulating Valve (Water-cooled Units Only) ......................................................................... 44
Drive Coupling Alignment ................................................................................................................................. 45-47
Section IX - Troubleshooting
Troubleshooting ................................................................................................................................................. 48-57
Section X - Maintenance Schedule
Maintenance Schedule ............................................................................................................................................. 58
Appendix A - Dimensional Drawings
Dimensional Drawings ....................................................................................................................................... 60-75
Appendix B - Technical Data
Technical Data ......................................................................................................................................................76-84
Addendum 1 - QSI Logo Controller
PLC Logo Controller Addendum (added 03/04) ..................................................................................................85-86
Section I - General
Standard Warranty
Quincy Compressor Division
Industrial Screw Products
®
QSI - Rotary Screw Air Compressors
Seller warrants products of its own manufacture against Seller’s sole obligation on this warranty shall be, at its
defects in workmanship and materials under normal use option, to repair, replace or refund the purchase price of
and service, as follows: any product or part thereof which proves to be defective.
If requested by Seller, such product or part thereof must
be promptly returned to Seller, freight collect for
QSI® Packaged Compressors - Twelve (12) months inspection.
from date of start-up or twenty-four (24) months from
date of shipment from the factory, whichever occurs first. Seller warrants factory repaired or replaced parts of its
own manufacture against defects in material and
workmanship under normal use and service for ninety
Airend on Packaged Compressors - (for service at (90) days or for the remainder of the warranty on the
full-load pressure at or below 150 psig) twenty-four product being repaired, whichever is longer.
(24) months from date of start-up or from date of
shipment from the factory, whichever occurs first. This warranty shall not apply and Seller shall not be
responsible nor liable for:
Airend on Packaged Compressors - (for service at
full-load pressure above 150 psig) Twelve (12) months a) Consequential, collateral or special losses or
from date of start-up or twenty-four (24) months from damages;
date of shipment from the factory, whichever occurs first. b) Equipment conditions caused by fair wear and tear,
abnormal conditions of use, accident, neglect or
Remanufactured Airend - Twelve (12) months from misuse of equipment, improper storage or damages
date of shipment from the factory. resulting during shipment;
c) Deviation from operating instructions,
Parts - Ninety (90) days from date of Distributor sale or specifications, or other special terms of sales;
one (1) year from date of factory shipment. d) Labor charges, loss or damage resulting from
improper operation, maintenance or repairs made by
person(s) other than Seller or Seller’s authorized
With respect to products not manufactured by Seller, service station.
Seller will, if practical, pass along the warranty of the e) Improper application of product.
original manufacturer.
In no event shall Seller be liable for any claims, whether
arising from breach of contract or warranty of claims of
Notice of the alleged defect must be given to Seller in negligence or negligent manufacture, in excess of the
writing with all identifying details including serial purchase price.
number, model number, type of equipment and date of
purchase, within thirty (30) days of the discovery of same
during the warranty period.
NOTICE!
This warranty is the sole warranty of seller. Any other warranties, expressed or implied,
including any warranties of merchantability or fitness for a particular use are hereby
excluded.
Quincy Compressor-QSI® 1
Section I - General
• Safety Alert Symbols

• Safety Precautions
• Spare Parts Ordering Information
• Serial/Model Identification Plate
• Model Identification
Safety Alert Symbols
IMPORTANT!
Throughout this manual we have identified key hazards. The following symbols identify the level of hazard
seriousness:
DANGER! WARNING!
This symbol identifies immediate hazards which This symbol identifies hazards or unsafe practices
will result in severe personal injury, death or which could result in personal injury, death or
substantial property damage. substantial property damage.
DANGER! CAUTION!
This symbol identifies life threatening electrical Identifies hazards or unsafe practices which could
voltage levels which will result in severe personal result in minor personal injury or property
injury or death. All electrical work must be damage.
performed by a qualified electrician.
CAUTION! NOTICE!
Identifies important installation, operation or
This symbol identifies hot surfaces which could maintenance information which is not hazard
result in personal injury or property damage. related.
DANGER!
Air from this compressor will cause severe injury or death if used for
breathing or food processing. Air used for these processes must meet
OSHA29CFR1910 OR FDA21XDE178.3570 regulations.
2 Quincy Compressor-QSI®
Section I - General
Safety Precautions • Do not change the pressure setting of the pressure

relief valve, restrict the function of the pressure relief
Read this manual and follow all instructions prior to valve, or replace the pressure relief valve with a
installing or operating this compressor. plug. Over pressurization of system or compressor
components can occur, resulting in death, severe
Listed below are some, but not all, safety precautions that personal injury or property damage.
must be observed with compressors and compressed air
systems. • Never use plastic pipe, rubber hose, or soldered
joints in any part of the compressed air system.
Failure to ensure system compatibility with
compressor piping is dangerous.
WARNING!
• Never use a flammable or toxic solvent for cleaning
Failure to follow any of these precautions may the air filter or any parts.
result in severe personal injury, death, property
• Do not remove any guards or cabinet panels or
damage and/or compressor damage.
attempt to service any compressor part while the
compressor is operating.
• Air from this compressor will cause severe injury or
death if used for breathing or food processing. Air • Do not operate the compressor at pressures in excess
used for these processes must meet OSHA 29 CFR of its rating.
1910.134 regulations.
• Observe control panel displays daily to ensure
• Disconnect and lockout all power supplies to the compressor is operating properly.
compressor plus any remote controllers prior to
servicing the unit. • Follow all maintenance procedures and check all
safety devices on schedule.
• Never assume it is safe to work on the compressor
because it is not operating. Many installations have • Never disconnect or tamper with the high air
automatic start/stop controls and the compressor may temperature (HAT) sensors.
start at any time.
• Compressed air is dangerous, do not play with it.
• This compressor is designed for use in the
compression of normal atmospheric air only. No • Use the correct fluid at all times.
other gases, vapors or fumes should be exposed to • Do not rely on the discharge air line check valve.
the compressor intake, nor processed through the
compressor. • Do not override any safety or shutdown devices.
• Relieve all pressure internal to the compressor prior • Keep doors closed during operation. The noise level
to servicing. Do not depend on check valves to hold inside cabinet exceeds 100 decibels (dBA) and the
system pressure. operating temperature of some components is
sufficient to burn the skin.
• A properly sized pressure relief valve must be
installed in the discharge piping ahead (upstream) of NOTICE!
any shut-off valve (block valve), heat exchanger,
These instructions, precautions and descriptions
orifice or any potential blockage point. Failure to
cover standard Quincy manufactured QSI® Series
install a pressure relief valve could result in the
air compressors. As a service to our customers,
rupturing or explosion of some compressor
we often modify or construct packages to the
component.
customers specifications. This manual may not
be appropriate in those cases.
Section I - General
NOTICE! Serial/Model Identification Plate

Every effort has been taken to ensure complete
and correct instructions have been included in this
manual, however, possible product updates and
changes may have occurred since this printing.
Quincy Compressor reserves the right to change
specifications without incurring any obligation for
equipment previously or subsequently sold. Not
responsible for typographical errors.
Spare Parts Ordering Information Reference to the machine MODEL, SERIAL NUMBER
and DATE OF ORIGINAL START-UP must be made in
BFGoodrich, Quincy Compressor Division maintains all communication relative to parts orders or warranty
replacement parts for Quincy compressors. A repair parts claim. A model/serial number plate is located on the
list is shipped with all new machines. Order parts from frame or in the upper right corner of the control panel
your Authorized Quincy distributor. Use only genuine door.
Quincy replacement parts. Failure to do so may void
warranty.
Section I - General
MODEL IDENTIFICATION
• General Description
• The Compression Cycle
• Air Flow
• Cooling System
• Capacity Control System
• Electrical System
• Indicators
• Gauges
General Description The Compression Cycle
QSI compressors are single stage, positive displacement, The compression cycle of a rotary compressor is a
fluid-flooded rotary screw type compressors containing continuous process from intake to discharge with no
two precision-machined rotors. A motor directly drives reciprocating mechanisms starting and stopping as found
the male rotor through a flexible drop out type coupling in reciprocating compressors. The compressor consists
with no step up or step down gearing used. The male of two rotors in constant mesh, housed in a cylinder with
rotor has four lobes that mesh with a female rotor two parallel adjoining bores. The male drive rotor has
consisting of six flutes. Both rotors are housed in a four lobes that mesh with six flutes in the female rotor.
single cast iron cylinder. The unit has an inlet port at the All parts are machined to exacting tolerances.
power input end and a discharge port at the opposite end.
As the rotors rotate, (male-clockwise as viewed from the
Most models are equipped with a positive displacement power input end) air is drawn into the cylinder through
fluid pump mounted to the compressor to circulate fluid the inlet port located at the power input end. A volume
through the system. Models without a fluid pump use of air is trapped as the rotor lobes pass the inlet cut off
positive pressure in the reservoir to circulate the fluid. points in the cylinders. Compression occurs as the male
rotor rolls into the female flute, progressively reducing
All components are attached to a heavy-duty steel frame. the space thereby raising the pressure. Compression
Controls and indicators are arranged on a control panel. continues until the lobe and flute pass the discharge port.
Acoustical cabinets are available to reduce sound levels. The compressed air is then discharged into the air/fluid
reservoir. There are four complete compression cycles
for each complete rotation of the male rotor.
INLET PORT
CYLINDER
MALE
ROTOR
FEMALE ROTOR DISCHARGE PORT
A) INTAKE B) COMPRESSION C) DISCHARGE
Figure 2-1. Compression Cycle
Air Flow Water-cooled Fluid Coolers
With the compressor operating, a partial vacuum is Water-cooled fluid coolers are of the shell and tube
produced at the compressor inlet. Air entering via the design. Fluid passes through the shell transferring its
compressor air filter flows through the air inlet valve into heat to the water flowing through the tubes. Fluid
the rotor housing where it is compressed, then discharged leaving the cooler does not pass through a thermal
into the air/fluid reservoir. Compressed air passes mixing valve as in an air-cooled unit, but goes directly to
through the complete system then through a minimum the fluid filter and the compressor. Fluid discharge
pressure check valve to the service connection. temperature at the compressor is maintained by a water
temperature regulating valve located in the discharge
water line. The water temperature regulating valve uses a
Cooling System probe to sense fluid temperature and opens and closes,
governing water flow through the cooler.
Fluid Coolers
Aftercoolers
Fluid coolers may use either air or water as a cooling
medium. The following descriptions point out the major Aftercoolers reduce the amount of water in the discharge
differences between the two types of coolers. air. They are used to lower the temperature of the
discharge air thereby condensing water vapor from the
Air-cooled Fluid Coolers compressed air. This allows most of the contained water
to be trapped and expelled from the unit, reducing water
The air-cooled fluid cooler and aftercooler are of the related problems downstream.
finned aluminum tube, one piece design. Ambient air is
forced through the fins by a motor driven fan, cooling the Air-cooled aftercoolers are part of the air-cooled fluid
fluid and air in the tubes. To maintain proper compressor cooler. Cooling air from the fan is blown through the
operation, the ambient air temperature should not exceed aftercooler and the fluid cooler.
the temperatures listed in Appendix B - Technical Data.
The cooler fins must be kept clean at all times. Fluid Water-cooled aftercoolers are placed in series with the
leaving the receiver passes through a thermal mixing fluid cooler. Incoming water is first directed through the
valve before traveling on to the cooler. The purpose of aftercooler and then on to the fluid cooler.
the thermal valve is to maintain a minimum fluid
discharge temperature at the compressor of A combination moisture separator and water trap is
approximately 180°F. provided for collecting and expelling water to the
customer’s drain.
Capacity Control System Auto/Dual (Standard)
As the motor starts driving the compressor rotors, air is The Auto/Dual system offers two choices of controlling
drawn in, compressed and discharged into the air/fluid the Quincy QSI Compressor. With the selector switch in
reservoir. When the air pressure in the air/fluid reservoir the Continuous Run position, the compressor operates
exceeds the set point of the pilot valve (normally 110 continuously, matching air demand as the differential
PSIG), the valve opens and passes a controlled volume of pilot valve controls the position of the inlet valve. When
air to the inlet valve air cylinder. maximum system pressure is reached, the pressure switch
opens, venting the air/fluid reservoir and, although the
NOTICE! compressor continues to run unloaded, no air is
compressed.
Other pressures are available optionally.
When the Auto Dual mode is selected, the compressor
The air forces a piston to move within the cylinder,
will also perform as above; however, a solid state timer is
closing the inlet valve. The compressor will continue to
activated when the pressure switch contacts open. This
run, matching air demand with air delivery by constantly
timer is adjustable within a ten (10) minute range. When
adjusting the position of the inlet valve. The inlet valve
the timer reaches the end of its delay period, the
regulates compressor capacity between 100% and nearly
compressor will automatically shut down and assume a
0% of rated delivery.
“standby” mode. Upon a drop in system air pressure, the
pressure switch contacts close, restarting the compressor
When maximum pressure (typically 10 PSIG above
automatically. The timer should be set, during unit start-
normal full load pressure) has been obtained in the air
up, for a minimum of six (6) minutes.
system, complete compressor unloading occurs. The
pressure switch located in the control panel sends a signal
During the unloaded/timing mode, if plant pressure
to the control and the solenoid valve opens, venting the
should drop causing the pressure switch contacts to close,
residual pressure from the blowdown valve. At the same
the compressor will continue to operate, resetting the
time, control air from the reservoir check valve is
timer and instructing the inlet valve to reopen.
directed through the solenoid to the inlet valve air
cylinder. The inlet valve is held in a closed position
preventing the intake of air into the compressor and
serving as a check valve preventing reverse air/fluid flow
through the inlet valve and air filter.
Auto/Demand (Optional) Load/No Load (Optional)
The QSI compressor with Auto/Demand controls In the Load/No Load mode, the compressor does not
accommodates external control signals from an optional modulate the inlet valve. The valve is either fully open
Quincy Demand-A-Matic multiple compressor controller. or it is closed. If systems demands include regular
periods of air usage at less than full load, a large
With the selector switch in the Local mode, the compressed air storage capability is required with this
compressor will operate exactly as described in the type of control. Without adequate storage, rapid cycling
previously mentioned Auto Dual description. may occur. This will cause wide system pressure
fluctuations that may affect the performance of
In the Remote mode, the compressor’s control panel is equipment using the compressed air. Load/No Load
bypassed in favor of the Demand-A-Matic multiple works with Auto-Dual control to turn the compressor off
compressor controller. The compressor will start, build during extended periods of no demand.
air, unload and shutdown on time delay as determined by
the Demand-A-Matic controller. With slight
modifications, a compressor equipped with Auto Dual
controls may be converted to Auto/Demand control. WARNING!
Contact your authorized Quincy Distributor.
Never assume it is safe to work on a compressor
Lead/Lag (Optional, two machines only) because it is not operating. It may be in standby
mode and could restart at any time. Follow all
This option allows one of two different pressure control safety instructions in the “Preparing for
settings to be chosen for a given machine. If the demand Maintenance or Service” chapter.
is greater than one unit’s capability, the second
compressor will automatically turn itself on until the
excess demand has been satisfied. Again, working with
the standard Auto-Dual control, the second machine
would time out and turn itself off after the demand
dropped.
Electrical System
A diagram of the electrical system is shown in the parts

DANGER!
manual sent with the compressor. A wiring diagram is
High voltage could cause death or serious injury.
also included in the control panel on all Quincy QSI
Disconnect all power supplies before opening the
compressors.
electrical enclosure or servicing.
NOTICE!
Due to continuing product improvements and
updates, it is suggested that the wiring diagram Safety Sensors
included in the control panel be used when
servicing the electrical control. Two high air temperature (HAT) sensors are standard on
the QSI units. These sensors protect the unit by sensing
Standard drive motors are open drip proof 1800 RPM unusually high temperatures and shutting the unit down.
with a maximum ambient temperature rating of 104°F. One is located in the discharge line from the compressor
They are not suitable for salt laden, corrosive, dirty, wet to the air/ fluid reservoir. The second is located in the top
or explosive environments. of the air/fluid reservoir. These sensors are set to trip at
approximately 225°F. The sensors are nonadjustable.
The QSI series compressors utilize 460V incoming power
through an across-the-line magnetic starter. A
transformer in the control panel reduces this voltage to
120 VAC for the various controls on the unit. These
controls include the selector switch, pressure switch,
timer, high air temperature safety switches, solenoid and WARNING!
the various indicator lights. Other incoming line voltages
are available as options. The compressor is provided Never remove, bypass or tamper with the safety
with a NEMA 1 enclosure. Optional panels include HAT switch. Failure to provide this safety feature
NEMA 4. could cause death or serious injury and property
damage. If the compressor is shutting down due
Air-cooled models utilize a second magnetic starter for to high discharge temperature, contact a qualified
protection of the fluid cooler fan motor. This starter is service technician immediately.
connected to the compressor starter through an interlock
which insures the fan motor is operating with the
compressor motor. If the fan motor starter trips out for
any reason, the compressor unit will shut down.
Indicators Gauges
Main Power on Light Hourmeter
Indicates when power from the main disconnect switch This gauge indicates actual hours of operation.
has been turned on and there is live power at the
compressor starter and control panel. This light will Air Pressure Gauge
remain on as long as there is power to the unit, regardless
of the position of the selector switch. This gauge indicates air pressure available for
distribution to the service line.
CAUTION!
CAUTION!
Always check power supply disconnect. The
Power-on light may be inoperable. Gauge may not register when the unit is unloaded
or off. Make certain all air pressure is relieved
prior to servicing.
High Discharge Air Temperature Light
Indicates when the unit has sensed an unusually high Air Outlet Temperature Gauge
discharge temperature.
This gauge indicates the temperature of the air/fluid
Fluid Filter Change Light mixture as it discharges from the compressor. The
normal reading is 170-190°F.
Indicates excessive pressure differential across the fluid
filter. It is used to determine fluid filter change intervals. Percent Capacity Gauge
Air/Fluid Separator Element Differential Light This gauge is graduated in percent of the total capacity of
the unit. Readings taken from this gauge give an
This indicates excessive pressure differential across the indication of the amount of air being used.
air/fluid separator element. It is used to determine
separator element change intervals.
Air Intake Filter Service Light
This indicator signals when the filter element needs to be

cleaned or replaced.
• Receiving
• Moving the Unit to the Installation Site
• Location
• Piping Connections
• Relief Valves
• Electrical
• Guards
• Manual Vent and Shutoff Valves
• Water and Sewer Facilities at the Installation
Site (Water-cooled models only)
• Compressor Rotation
• Fan Rotation
Receiving Moving the Unit to the Installation Site
Upon receipt, immediately inspect the compressor for Forklift slots are provided in one side and one end of the
any visible damage that may have occurred during main frame. Use of chains and slings should be limited
shipment. If visible damage is found, the delivering to the main frame. Do not attempt to lift the unit by
carrier should make a notation on the freight bill and the attaching to any components. Optional lifting eyes are
customer should request a damage report. If the available.
shipment is accepted and damage is found later, it is
classified as concealed damage. Concealed damage
should be reported to the delivering carrier within 15
days of delivery. The delivering carrier must prepare a
damage report. Itemized supporting papers are essential CAUTION!
to filing a claim.
Improper lifting may result in component, system
damage or personal injury. Follow good shop
Read the compressor nameplate to be sure the
practices and safety procedures when moving the
compressor is the model and size ordered and that
unit.
optionally ordered items are included.
Check the reservoir and pressure relief valves to be sure

they are adequate for the pressure at which you intend to
operate.
Location
Locate the compressor on a level surface in a clean, well-

lit and well-ventilated area. Allow sufficient space (four
CAUTION!
feet of clearance on all sides and top of the compressor)
Removal or modification of sound insulation
for safe and proper daily inspection and maintenance.
could result in dangerously high sound levels.
The entire length of the frame base must be supported.
Shim where necessary but do not use wood.
Quincy QSI compressors are essentially vibration free,
Ambient temperature should not exceed 110°F. High
however, some customers may choose to bolt the unit to
ambient temperatures may result in a high air temperature
the floor to prevent the accidental breakage of piping or
shutdown. All models are intended for indoor
electrical connections as a result of being bumped. Use
installation; however, it is possible, with certain
only lag bolts to secure the unit. Do not pull the bolts
modifications, to accommodate some outdoor locations.
down tight. Overtightening the lag bolts may place the
Cabinet models are water-resistant but not water tight.
frame in a twist or bind causing breakage of fluid coolers,
Sheltering from rain, snow and freezing temperatures is
piping and reservoirs.
mandatory.
WARNING! WARNING!
Under no circumstances should a compressor be
Do not operate in temperatures below 32°F or
installed in an area exposed to a toxic, volatile or
above the limits outlined in Appendix B -
corrosive atmosphere, nor should toxic, volatile
Technical Data.
or corrosive agents be stored near the compressor.
Do not locate the unit where the hot exhaust air from
other compressors or heat generating equipment may be
Piping Connections
drawn into the unit. Never restrict the flow of exhaust air
from the fluid cooler or cooling fan. Heated exhaust air Never join pipes or fittings by soldering. Lead-tin
must be exhausted outside to prevent high temperature solders have low strength, a low creep limit, and may,
conditions in the compressor room. If the room is not depending on the alloy, start melting at 360°F. Silver
properly ventilated, compressor operating temperatures soldering and hard soldering are forms of brazing and
will increase and cause a high temperature shutdown. should not be confused with lead-tin soldering. Never
use plastic, PVC, ABS pipe or rubber hose in a
compressed air system.
Piping Fit-up
CAUTION!
Care must be taken to avoid assembling the piping in a
Clean, fresh air, of sufficient quantity, is required strain with the compressor. Piping should line up without
for proper compressor operation. having to be sprung or twisted into position. Adequate
expansion loops or bends should be installed to prevent
undue stress at the compressor resulting from the changes
In high humidity areas, avoid placing the compressor in a between hot and cold conditions. Pipe supports should
basement or other damp locations. Control the be mounted independently of the compressor and
compressor temperatures and monitor compressor fluid anchored, as necessary, to limit vibration and prevent
for signs of water contamination. Fluid and filter expansion strains. Piping should never be of smaller size
changes may need to be increased in high humidity areas. than the connection on the compressor unit.
Increased operating temperatures may be required.
Relief Valves Electrical
Pressure relief valves are sized to protect the system. Before installation, the electrical supply should be
Never change the pressure setting or tamper with the checked for adequate wire size and capacity. During
valve. Only the relief valve manufacturer or an approved installation, a suitable fused disconnect switch or circuit
representative is qualified to make such a change. breaker should be provided. Any unreasonable voltage
unbalance (5%) between the legs must be eliminated and
any low voltage corrected to prevent excessive current
draw. The installation, electric motor, wiring and all
DANGER! electrical controls must be in accordance with National
Electric Code, and all state and local codes. A qualified
Relief valves are to protect system integrity in electrician should perform all electrical work. Air
accordance with ANSI/ASME B19 safety compressors must be grounded in accordance with
standards. Failure to provide properly sized relief applicable codes. See control panel for the proper
valves will result in death or serious injury. wiring diagram.
Quincy would like to emphasize the importance of

Relief valves are to be placed ahead of any potential providing adequate grounding for air compressors. The
blockage point that includes, but is not limited to, such common practice of grounding units to building
components as shut-off valves, heat exchangers and structural steel may not actually provide adequate
discharge silencers. Ideally, the relief valve should be grounding protection, as paint and corrosion build-up
threaded directly into the pressure point it is sensing, not may exist.
connected with tubing or pipe and pointed away from any
personnel. Always direct discharge from relief valves to
a safe area away from personnel.
CAUTION!
NEMA electrical enclosures and components
must be appropriate to the area in which they
are installed.
Pneumatic Circuit Breakers or Velocity Fuses
The Occupational Safety and Health Act, Section

1926.303 Paragraph 7 published in Code of Federal
Figure 3-1. Relief Valve Regulations 29 CFR 1920.1 (revised 07/01/1982), states
“all hoses exceeding 1/2” inside diameter shall have a
safety device at the source of supply or branch line to
reduce pressure in case of a hose failure.” These
CAUTION! pneumatic safety devices are designed to prevent hoses
from whipping, which could result in a serious or fatal
ASME coded pressure vessels must not be accident.
modified, welded, repaired, reworked or
subjected to operating conditions outside the
nameplate ratings. Such actions will negate code
Guards
status, affect insurance status and may cause
death, serious injury and property damage.
All mechanical action or motion is hazardous in varying
degrees and needs to be guarded. Guarding shall comply
with OSHA Safety and Health Standards 29 CFR
1910.219 in OSHA manual 2206 (revised 11/07/1978)
and any state or local codes.
Manual Vent and Shutoff Valve Clean air is essential for your Quincy QSI compressor.
Always select a source providing the cleanest air
Install a manual valve to vent the compressor and the possible. When an outside air source is used, keep all
compressor discharge line to atmosphere. If the air piping as short and direct as possible. Use vibration
receiver tank services a single compressor, the manual isolators and support all piping correctly. Piping size
valve can be installed in the receiver. When a manual should be at least as large as the inlet valve opening and
shut-off valve (block valve) is used, a manual valve increased several sizes for extremely long piping runs.
should be installed upstream from the valve, and a The piping must be leak free and clean after fabrication.
pressure relief valve installed upstream from the manual
vent valve. These valves are to be designed and installed
to permit maintenance to be performed in a safe manner.
Never substitute a check valve for a manual shut-off
WARNING!
valve (block valve) if the purpose is to isolate the
Relieve compressor and system air pressure by
compressor from a system for servicing.
opening the appropriate manual relief valve prior
to servicing. Failure to relieve all system pressure
could result in death or serious injury and
WARNING! property damage.
Removal or painting over safety labels will result

in uninformed conditions. This could result in Compressor Rotation
personal injury or property damage. Warning
signs and labels shall be provided with enough Compressor rotation must be checked prior to start-up.
light to read, conspicuously located and Proper rotation is clockwise (as viewed from the power-
maintained for legibility. Do not remove any input end). The power-input end of the compressor is
warning, caution or instructional material marked with an arrow noting the proper rotation.
attached. Operating the compressor in incorrect rotation will result
in extreme damage to the compressor and warranty
coverage will be voided. To check for proper rotation,
Water and Sewer Facilities at the Installation Site jog the starter button, allowing the motor to turn 2 or 3
(Water-cooled models only) revolutions. Observe the drive element for correct
direction. If incorrect rotation is observed, lock out
Make sure the water supply is connected and open. power supply, reverse electrical leads L1 and L3 at the
Piping supplied by the user should be at least equal to the motor starter. Recheck for correct rotation.
connections provided on the compressor. Sewer facilities
should be readily accessible to the installation site and
meet all the requirements of local sewer codes, plus those Fan Rotation (Air-cooled only)
of the compressor. Make sure water inlet and discharge
connections are correct. Check the fan rotation at the same time the compressor
rotation is being checked. Fan airflow should be
NOTICE! outward, that is, pushing the air through the coolers.
The water temperature regulating valve is located
in the discharge water line.
• Prior to Starting
• Starting the Compressor
• Stopping the Compressor - Normal
Operation
• Stopping the Compressor - Emergency
Prior to Starting • Close the main power disconnect switch and jog the
starter switch button to check the rotational direction
of the compressor.
CAUTION! • Check the fan rotation (air flows through the

coolers).
Provisions should be made to have the instruction
manual readily available to the operator and • Water-cooled models - Check inlet and discharge
maintenance personnel. If, for any reason, any water piping for proper connections.
parts of the manual become illegible or if the
manual is lost, have it replaced immediately. The
instruction manual should be read periodically Starting the Compressor
to refresh one’s memory. This may prevent a
serious accident. • Secure all enclosure panels on compressor.
Before starting the compressor, review Sections II and III • Open the service valve to the plant air distribution
of this manual. Be certain that all installation system.
requirements have been met and that the purpose and use
of the controls are thoroughly understood. Before • Select the mode of operation and start the
placing the compressor into operation, do the following: compressor.
• Remove all loose items and tools from around the
• Watch for excessive vibration, unusual noises or air/
compressor.
fluid leaks. If anything unusual develops, stop the
• Check fluid level in the air/fluid reservoir. See compressor immediately and correct the condition.
Compressor Fluid Section.
• Control settings have been adjusted at the factory;
• Check the fan and fan mounting for tightness. however, they should be checked during start-up and
readjusted, if necessary. Some applications may
• Manually rotate the compressor through enough require a slightly different setting than those
revolutions to be certain there are no mechanical provided by the factory. Refer to the Service
interferences. Adjustment Section VIII. Never increase air
pressure settings beyond factory specifications.
• Check all pressure connections for tightness.
• Adjust the water temperature regulating valve to
• Check to make sure all relief valves are in place. maintain 180°F discharge air temperature (water-
• Check to make sure all panels and guards are in cooled units only).
place and securely mounted. • Observe compressor operation closely for the first
• Check fuses, circuit breakers and thermal overloads hour of operation and frequently for the next seven
for proper size. hours. Stop and correct any noted problems.
Stopping the Compressor - Normal Operation Stopping the Compressor - Emergency
Close the service valve to the plant air distribution Press the emergency stop button or cut the power at the
system. Allow the pressure to build within the reservoir main disconnect switch or panel.
and the compressor to fully unload. Press the stop button
or remove power at the main disconnect switch or panel.
NOTICE!
Close the service valve when the compressor is
not being used to prevent the system’s air pressure
from leaking back into the compressor if the check
valve leaks or fails.
Section V - Preparing for Maintenance or Service
The following procedure should be followed for

maximum safety when preparing for maintenance or
service:
1) Disconnect and lockout the main power switch and

hang a sign at the switch of the unit being serviced.
WARNING!
2) Close shut-off valve (block valve) between receiver
and plant air system to prevent any back-up of air Never assume the compressor is ready for
flow into the area to be serviced. NEVER depend maintenance or service because it is stopped. The
upon a check valve to isolate the system. automatic dual control may start the compressor
at any time. Death or serious injury could result.
3) Open the manual vent valve and wait for the
pressure in the system to be completely relieved
before starting service. DO NOT close the manual
vent valve at any time while servicing.
4) Shut off water and depressurize system if water-

cooled.
THIS PAGE INTENTIONALLY LEFT BLANK
• Safety
• Water Removal
• Air/Fluid Separator Element
• Fluid Scavenging System
• Air Filter
• Control Line Air Filter
• Shaft Seal
• Air and Fluid Tubing
• O-ring Fittings
Safety Water Removal
NOTICE! Water vapor may condense in the reservoir and must be

Maintenance should be performed by trained and removed. The frequency with which water must be
qualified technicians only. removed is determined by the ambient air conditions.
During hot and humid conditions, water should be
Safety procedures while servicing the compressor are drained off the bottom of the reservoir daily. In cold and
important to both the service personnel and to those who dry conditions, water may only need to be drained
may be around the compressor and the system it serves. weekly. To drain water from the reservoir, turn the
Listed below are some, but not all, procedures that should compressor off and let sit for at least 5 minutes. Then
be followed: open the drain valve. Water is heavier than the
compressor fluid and will collect at the bottom of the
• Wait for the unit to cool before starting service. reservoir. When the drain is first opened some
Temperatures may exceed 180°F when the compressor fluid may come out before the water starts to
compressor is operating. flow. Close the valve when the water flow changes to
compressor fluid. Make certain that there is no pressure
• Clean up fluid spills immediately to prevent slipping. in the reservoir before opening the drain valve. Water
content in the compressor fluid in excess of 200 PPM
• Loosen, but do not remove, flange or component could cause bearing damage and airend failure.
bolts. Carefully pry apart to be sure there is no
residual pressure before removing bolts.
Air/Fluid Separator Element
• Never use a flammable solvent such as gasoline or
kerosene for cleaning air filters or compressor parts.
The separator element is a one piece construction that
• Safety solvents are available and should be used in coalesces the fluid mist, passing through the filtering
accordance with their instructions. media, into droplets that fall to the bottom of the
separator element to be picked up by a scavenging tube
and returned to the compressor. Use care when handling
the separator element to prevent it from being damaged.
CAUTION! Denting may destroy the effectiveness of the filtering
media and result in excessive fluid carryover. Even a
Unusual noise or vibration indicates a problem.
very small hole punctured through the element will result
Do not operate the compressor until the source
in a high fluid carryover. Larger models use two air/fluid
has been identified and corrected.
separator elements.
4) Touch the top cap of the separator element with the

other probe. The indicator light should illuminate
WARNING! on the test or the v-o-m test must read no more than
20 ohms.
Do not remove the staples from the separator
element. Their function is to prevent an 5) Touch the bottom cap of the separator element. The
electrostatic build-up which could spark a fire. indicator light should illuminate on the test or the v-
Use genuine Quincy replacement separators. o-m test must read no more than 20 ohms.
6) Touch the outside wire mesh. The indicator light

Continuity Testing of Separator Elements should illuminate on the test or the v-o-m test must
read no more than 20 ohms.
NOTICE!
Electrical continuity between all separator 7) Touch the inside wire mesh ( do not puncture the
element metal surfaces must be checked prior to element media). The indicator light should
replacing any separator element. Do not install illuminate on the test or the v-o-m test must read no
if continuity is not present. Return the separator more than 20 ohms.
element to your Quincy Distributor for
replacement. 8) If the separator element has a gasket on each side of
the flange, repeat steps 3 through 7.
Prior to installation, test the separator element as follows:
9) If the separator element fails any of the above test ,
1) Locate a continuity test light or a volt-ohm-meter return it to your Quincy Distributor for replacement.
(v-o-m) capable of reading 20 ohms.
10) Make sure the compressor is bonded (wired) to an
2) Assure that battery has proper charge. Touch the earth ground to dissipate static electricity.
probe leads together to assure the light works or to
zero calibrate the meter.
3) Contact the grounding staple on the separator

element gasket with the ground probe of the test
indicator.
Fluid Scavenging System Air Filter
Fluid from inside the separator element is returned to the A heavy-duty air filter is standard on all QSI models.
inlet valve or airend by a scavenger tube positioned The heavy-duty air filter is a two stage, dry type element.
inside the separator element, through an orifice and tube The first stage is cyclonic. That is, centrifugal airflow
connected to the compressor. Failure to keep the orifice spins the larger dirt particles to the outside walls of the
clean will result in excessive fluid carryover. Cleaning of filter canister. In the second stage, air passes through the
the orifice should be performed as follows: filter element with an efficiency of 99.9% as tested by
• When no fluid is seen moving through the sight SAE J7266 test code specifications. Removal and
glass. replacement of the element is accomplished by
unscrewing the wing nut and exchanging the element.
• When excessive fluid carryover is detected. Tighten the wing nut snugly after making certain the
element is seated correctly on its mounting base.
• Every fluid change.
• Once per year. NOTICE!

Intake filtration equipment supplied from the
NOTICE! factory may not be adequate for extremely dirty
Do not ream the orifice or change the orifice size. applications or some forms of dust or vapors. It
Do not install the orifice reversed. is the customer’s responsibility to provide
adequate filtration for those conditions.
Warranty will be voided if inadequate filtration
causes a failure.
Control Line Air Filter
An automatic draining control line filter is used.

Draining occurs only when the compressor is in the
Figure 6-1. Scavenge Line Sight Glass unloaded condition.
Shaft Seal • Insert two of the seal adapter retaining bolts into the
seal adapter jack holes and turn clockwise (pushing
Compressor shaft seals are wear items that may the seal adapter away from the suction housing).
eventually have to be replaced. Special tools and a
complete understanding of the installation procedure are • After the seal adapter outer o-ring has cleared the
required for a successful seal replacement. Ask your seal adapter bore, remove the adapter for inspection.
Quincy distributor for complete illustrated instructions
(available as a Service Alert) at the time you order the • Disassemble the seal adapter as follows:
seal and special tools, if you decide to replace the seal
yourself. If your distributor does not have a copy of a. With the face of the seal adapter up, insert two
these instructions, they can be ordered from Quincy small, flat screwdrivers under the outer lip of
Compressor at no charge. the fluid slinger and pop the slinger from the
seal adapter bore.
QSI compressors incorporate a fluid scavenge system to b. Using a brass drift, tap the shaft seal assembly
complement the use of a triple lip seal assembly. Any from the seal bore.
complaint of shaft seal leakage requires that the scavenge c. Inspect both seal lips for excessive wear, lip
system be inspected for proper operation prior to the flaws or damage.
replacement of the shaft seal. Proper inspection consists
of the following: d. Inspect the outer o-ring on the fluid slinger for
cuts or nicks.
• Assure that the scavenge line itself is not plugged. e. Inspect the outer o-ring on the seal adapter for
cuts and nicks.
• Inspect the performance of the scavenge line check f. Slide the wear sleeve removal tool over the end
valve by removing the fitting located at the bottom of the shaft and allow the jaws of the tool to
of the motor adapter. Remove the check ball and snap on the backside of the wear sleeve.
inspect for wear. If the check valve is stuck open, Tighten the outer shell of the tool down over
fluid can backflush from the airend into the seal the inner jaws.
cavity and appear as a leak. If the check valve is
stuck closed the seal cavity will not scavenge. g. Using a ratchet and socket, turn the puller jack
Replace if necessary. screw clockwise in against the end of the
compressor shaft to remove the seal wear
• Remove the coupling guards and coupling halves sleeve.
• Remove the drive coupling hub and key from the

compressor shaft.
CAUTION!
• Remove the drive motor.
Do Not use an impact wrench with this tool.
• Remove the four bolts securing the seal adapter to
the suction housing.
Preparation for New Seal Installation • Install a new o-ring around the scavenge port (use
petroleum jelly to hold the o-ring on the seal adapter
• Inspect the compressor shaft for burrs or deep face during installation).
scratches at the wear sleeve area. Using a 100-grit
emery cloth, lightly sand horizontally any rust or • Carefully slide the seal adapter with the new seal
Loctite™ on the shaft. Using a fine file or emery installed over the end of the rotor shaft and up
cloth, deburr the key area of the rotor shaft. Cover against the adapter bore.
the keyway with masking tape to prevent damage to
the new seal during installation. • Using care not to damage the o-ring, evenly draw the
adapter into the bore, install the four retaining bolts
• Clean the seal adapter with fast drying solvent. and tighten to the specified torque.
Assure that the scavenge drain in the seal adapter is
clean and open. Place the outer face of the seal • Remove the installation sleeve.
adapter on a flat, hard surface.
• Apply a thin film of compressor fluid to the o-ring
• Remove the new triple lip seal from the package and
and seal lip of the outer fluid slinger.
inspect for damage or imperfections on the seal lips.
• Apply a thin coat of Loctite™ 290 to the outer steel

• Install the outer slinger over the end of the rotor shaft
case of the seal and position the seal in the seal and push into the scavenge bore using both thumbs.
adapter bore.
• Reinstall drive motor, and coupling.
• Insert the proper seal driver over the seal. Insert the
proper wear sleeve driver in the seal driver and tap • Reinstall the coupling guards before starting the
the new seal into the bore with a medium sized compressor.
hammer.
• Preheat the wear sleeve (in a small oven) to 350°F.

Do not preheat in warm oil.
• Apply a thin film of Loctite™ to the inner diameter Air and Fluid Tubing
of the wear sleeve and immediately install on the
compressor shaft using the proper wear sleeve driver. Flareless tubing is used in the air piping to eliminate pipe
Drive the wear sleeve on the shaft until the driver joints and provide a cleaner appearance. Replacement
bottoms on the shaft shoulder. tubing and fittings are available; however, special
installation procedures must be followed. Your
Seal Installation
authorized distributor has the necessary instructions and
experience to perform these repairs.
• Apply a thin coat of compressor fluid to the outer
face of the wear sleeve and seal lip.
• Slide the proper seal installation sleeve against the WARNING!

wear sleeve with the taper toward the end of the rotor
shaft. Failure to install flareless tubing or fittings
correctly may result in the tubing coming apart
• Install a new o-ring on the seal adapter and lubricate under pressure. Serious injury and property
with compressor fluid. damage may result.
ASSEMBLING THE FACE SEAL END
1) CHECK SEALING SURFACES 3) POSITION TO FITTING
ENSURE THAT O-RING IS PROPERLY

SEATED IN THE GROOVE.
CHECK SEALING SURFACE POSITION AND HOLD FLAT SEALING

AND GROOVE FOR DAMAGE FACE AGAINST O-RING.
OR MATERIAL BUILDUP.
2) INSTALL O-RING 4) THREAD ON NUT BY HAND &

5) WRENCH TIGHTEN
IF PROPERLY ALIGNED, THE NUT

SHOULD THREAD ON EASILY BY HAND.
CORRECTLY SIZED O-RING

IS 0.070” THICK AND ITS O.D. WRENCH TIGHTEN TO RECOMMENDED
TOUCHES THE OUTSIDE TORQUE FOR FACE SEAL END.
EDGE OF THE GROOVE.
ASSEMBLING ADJUSTABLE END TO PORT
1) CHECK SEALING SURFACES & INSTALL O-RING
• INSPECT FITTING FOR DAMAGE

LOCKNUT
• USE O-RING INSTALLATION TOOL TO INSTALL O-RING
BACKUP WASHER
• APPLY SMALL AMOUNT OF LUBRICANT TO O-RING
O-RING
2) BACK OFF NUT 3) THREAD INTO PORT 4) BACK OFF FOR ALIGNMENT 5) WRENCH TIGHTEN
BACK OFF LOCKNUT THREAD FITTING INTO POSITION FITTING FOR WRENCH TIGHTEN
TO ITS UPPERMOST THE PORT UNTIL THE ATTACHING LINE BY LOCKNUT
POSITION BACKUP WASHER UNTHREADING UP TO 360°
CONTACTS THE SURFACE
ASSEMBLING NON-ADJUSTABLE PORT END
• INSPECT SEALING SURFACES FOR DAMAGE
• INSTALL O-RING
• THREAD FITTING INTO PORT AND WRENCH TIGHTEN
SEAL-LOK ASSEMBLY TORQUES (IN LBS)

DASH SIZE 4 6 8 10 12 16 20 24
FACE SEAL 220 320 480 750 1080 1440 1680 1980
END (+/-) 10 (+/-) 25 (+/-) 25 (+/-) 35 (+/-) 45 (+/-) 90 (+/-) 90 (+/-) 100
• Fluid Specifications
• Lubrication
• Fluid Level
• Fluid Sample Valve
• Fluid Filter
• Factors Affecting Fluid Life
• Fluid Analysis Program - General
• QuinSyn PG
• QuinSyn XP
• QuinSyn Plus
• QuinSyn Fluids
• QuinSyn Flush
• Cleaning and Flushing With QuinSyn Flush
• Converting to QuinSyn PG
• Converting to QuinSyn XP
• Converting to QuinSyn Plus
• Converting to QuinSyn
• Sampling Procedures
• Understanding the Analysis Report
• Fluid Parameters
The three functions of compressor fluid are: A fluid tag is attached to each Quincy rotary screw
• to lubricate the bearings and rotors compressor indicating the type of fluid provided in the
initial fill. All of the above fluids are available from any
• to remove heat from the air as it is being compressed authorized Quincy distributor.
thus lowering the compressed air discharge
temperature
• to seal the rotor clearances

CAUTION!
Fluid Specifications Do not mix different grades or types of fluid. Do
not use inferior grades of fluids.
We recommend that all Quincy rotary screw compressors
be filled with one of the following synthetic fluids:
QuinSyn PG - Standard fill. (Replaces QuinSyn)

QuinSyn XP - Standard fill for high pressure
NOTICE!
applications. (Replaces QuinSyn HP Failure to follow these fluid recommendations will
68) adversely affect your warranty.
QuinSyn Plus- Extended life fluid.
QuinSyn - PAO fluid.
QuinSyn F - Food grade applications.
QuinSyn IV - 4000 hour alternative fluid.
Lubrication
Most Quincy compressors are equipped with a positive

displacement fluid pump mounted to the compressor and
directly driven by one of the rotors. Fluid is circulated
through the cooler, fluid filter, and into the compressor.
In the compressor, fluid is diverted through internal
passages to ensure positive lubrication of the bearings Figure 1-1. Fluid Level Sight Gauges
and shaft seal. The remainder of the fluid is injected at
the beginning stage of the compression cycle to seal
clearances and to cool and lubricate the rotors. Models Each unit comes equipped with a fluid level sight gauge,
not equipped with a fluid pump use pressure differential fluid fill opening, and a fluid drain in the reservoir. The
to circulate the fluid. Positive pressure maintained in the fill plug is drilled to allow some pressure to escape before
reservoir forces the fluid throughout the machine. the plug is completely removed. Should you hear
pressurized air venting through the hole, immediately
Each Quincy compressor is filled at the factory with the screw the plug back into the reservoir. Relieve the
correct amount of one of the synthetic fluid listed in the pressure in the machine before proceeding.
Fluid Specifications. Mineral oil can be requested and
used in specific applications. The use of other brands or
types of fluid may reduce the design life of the
compressor or cause problems with filtration or CAUTION!
carryover. Consult the Quincy Service Department
before changing brands of fluid. Hot fluid under pressure could cause death or
serious injury. Do not remove the fluid fill plug
and attempt to add fluid to the reservoir while
Fluid Level the compressor is in operation or when the system
is under pressure. Be sure that the compressor’s
Fluid level is monitored by a sightglass or a dial gauge red mushroom stop button is pushed in and locked
while in operation. Fluid level should be in the “run” and that the main power disconnect switch is in
area on the dial gauge or completely fill the sight gauge. the off position and locked out to assure that the
DO NOT OVER FILL. compressor will not start automatically.
Fluid Sample Valve
QSI models are equipped with a fluid sample valve

located at the discharge of the fluid filter.
Figure 1-3. Spin-on Fluid Filter
The initial filter change should occur after the first 500
Figure 1-2. Fluid Sample Valve hours of operation. During normal service, the filter
cartridge should be replaced under the following
Fluid samples should be taken from the sample valve conditions, whichever occurs first:
while the compressor is running at normal operating
temperature (see Sampling Procedures - page 39). • as indicated by the fluid filter maintenance indicator
when the fluid is at normal operating temperature
• every 1,000 hours

Fluid Filter
• every fluid change
The fluid filter is a spin on, full flow unit. Replacement
of the filter requires spinning off the cartridge and
replacing it with a new one. NOTICE!
The fluid filter maintenance indicator may read
NOTICE! high upon start up on cool mornings due to
Use genuine Quincy replacement filters only. sluggish fluid creating higher than normal
differential pressures. Monitor indicator after the
fluid warms up.
Factors Affecting Fluid Life Fluid Analysis Program - General
To protect your investment, check for the following, Quincy’s fluid analysis program is offered to all
which can affect the long life of QuinSyn: customers using QuinSyn fluids in Quincy Compressor
Rotary Screw Compressors. This service provides
1) High operating temperatures optimum drain intervals for compressors operating on
2) Contaminants: QuinSyn fluids. Monitoring of the total acid number
a. Other fluids (TAN), barium level and/or viscosity throughout the life
b. Strong Oxidizers such as: of the fluid provides maximum protection to your
• acids machine, while best utilizing the extended life features of
• sulfur QuinSyn.
• chlorine
• burnt fuel - The fluid analysis provides historical information,
i.e. exhaust from: forklifts, boilers, jet aircraft detailing items such as hours on the fluid, viscosity and
• nitrogen oxides total acid number (TAN). Should results appear unusual
• ozone or suspicious, a detailed analysis can pinpoint specific
• welding fumes contaminants. A detailed report is furnished to you, your
• plastic molding fumes Quincy Distributor and the Quincy Compressor factory
c. Ammonia upon completion of the fluid analysis.
d. Solvent fumes:
• chlorinated degreasers Although QuinSyn fluids are rated by hours of life
• ink solvents expectancy under normal operating conditions, it is
e. Airborne dust and particles recommended that fluid samples be taken every 500 to
f. Paper digester fumes 2000 hours and sent to Quincy Compressor Fluid
Analysis until a history of performance in a specific
Locate your compressor in the coolest area possible. For compressor application is established. Once the
every 18°F above 195°F, the operating life of any fluid is appropriate drain interval is established, the frequency of
reduced to about half that at 195°F. Some mineral oils the fluid analysis can be reduced unless operating
begin to form varnish at temperatures above 200°F. conditions change.
QuinSyn fluids are more forgiving than mineral oil at
high temperatures. QuinSyn XP is designed to operate at NOTICE!
sustained temperatures above 200°F. The life of other All Quincy Compressor extended airend
QuinSyn fluids will be shortened at high temperatures. warranty programs require that fluid samples be
sent to Quincy Compressor Fluid Analysis a
Air intake should provide contaminant-free, cool air. A minimum of every 2,000 hours.
Quincy heavy-duty intake filter will reduce the risk of
abrasion and increased wear. An air filter does not The depletion of antioxidants, change of viscosity,
eliminate reactive gases. Inspect your filter monthly and barium and acid levels all occur with time. It is
replace as required. extremely important to change QuinSyn before the
antioxidants are completely depleted. If the fluid is left
in the compressor beyond its useful life, removing all of
the spent fluid is difficult. The oxidation products
remaining can considerably shorten the life of the new fill
of QuinSyn fluid.
QuinSyn PG Disposal
Effective on orders entered on June 1, 2000 and later, QuinSyn PG is considered nonhazardous waste. Disposal
Quincy’s factory fill fluid changed from QuinSyn to of this fluid should be done in accordance with Local,
QuinSyn PG. Orders placed prior to June 1, 2000 State, and Federal regulations. Separation of this fluid
shipped with QuinSyn. from condensate will require those separators designed to
handle fluid emulsions. The QIOWA fluid/water
QuinSyn PG is a custom blended polyalklene glycol/ester separator is suitable for separation of fluid emulsions
(PAG). QuinSyn PG is an ISO 46 viscosity fluid with an such as QuinSyn PG. Please contact Quincy’s Service
8,000 hour life under normal operating conditions (exact Department for more details.
fluid life is determined by the fluid sampling program)
and is the chosen fluid for Quincy’s new five-year airend Fluid Analysis Program
warranty effective June 1, 2000 (see Blue Alert #566).
Under extended warranty conditions QuinSyn PG fluid The fluid sampling for QuinSyn PG has been extended to
life is rated at 8,000 hours or one year, whichever occurs 2,000 hours because of the superior quality and forgiving
first. nature of this fluid. The new five-year extended warranty
with QuinSyn PG requires 2,000 hour sampling as a
Typical Properties of QuinSyn PG ISO 46 condition of maintaining the warranty.
Viscosity @ 100°F ASTM D445 52.4 cSt. NOTICE!

Viscosity @ 210°F ASTM D445 9.4 cSt. To maintain warranty compliance, fluid samples
Viscosity Index ASTM D2270 163 of QuinSyn PG must be sent to Quincy
Specific Gravity 60/60 0.98 Compressor Fluid Analysis a minimum of every
Flash Point ASTM D92 485°F 2,000 hours.
Fire Point ASTM D92 525°F
Because this fluid differs from QuinSyn, different
Applications methods are employed to evaluate the fluid in the
sampling program. Primary concerns with this fluid are
QuinSyn PG is the recommended fluid in high humidity the total acid number (TAN) and barium levels. QuinSyn
applications due to its ability to hold water. QuinSyn PG PG will not be condemned on water percentage nor
is best suited for applications where high humidity exists antioxidants but will be condemned on low barium and
and the machine cannot be shut down to drain water from high TAN values. The barium in the fluid acts as a
the reservoir. corrosion inhibitor, therefore we have set low limits for
this additive (see page 42 for limits).
QuinSyn XP Applications
Effective on orders entered on June 1, 2000 and later, QuinSyn XP is designed for applications where the fluid
Quincy Compressor began offering our new long life is exposed to elevated temperatures for extended periods
synthetic fluid, QuinSyn XP. QuinSyn XP is the new of time. Fluid thermostat temperature settings can be
factory fill for high pressure units (defined as units over elevated to assist in reducing water content in the fluid in
125 psig full flow). QuinSyn XP replaces QuinSyn HP 68 high humidity applications. Consult Quincy’s Service
as our high pressure fluid and is totally compatible with Department before making thermostat changes.
QuinSyn HP 68 (the fluids can be mixed together with
absolutely no problems). Aftermarket pail and drum Disposal
orders for QuinSyn HP 68 will be filled with QuinSyn
XP. QuinSyn XP is considered nonhazardous waste. Disposal
of this fluid should be done in accordance with Local,
QuinSyn XP is a custom blended polyolester (POE) fluid State, and Federal regulations. Should condensate need
ideally suited for rotary screw air compressors. QuinSyn to be treated, Quincy’s QIOW fluid/water separators are
XP is an ISO 68 viscosity fluid with a 12,000 hour life at required.
100 & 125 psig full flow under normal operating
conditions and 8,000 hours as a high pressure fluid Fluid Analysis Program
(exact fluid life is determined by the fluid sampling
program). QuinSyn XP is the only fluid available with QuinSyn XP will be analyzed similar to QuinSyn
Quincy’s ten-year airend warranty (see Blue Alert #566). although the primary concern is the total acid number
(TAN). Supplemental “on site” TAN kits will be
Typical Properties of QuinSyn XP ISO 68 applicable to this fluid as well as QuinSyn PG.
Viscosity @ 100°F ASTM D445 60.0 cSt. NOTICE!

Viscosity @ 210°F ASTM D445 9.8 cSt. To maintain extended warranty compliance, fluid
Viscosity Index ASTM D2270 131 samples of QuinSyn XP must be sent to Quincy
Specific Gravity 60/60 0.95 Compressor Fluid Analysis a minimum of every
Flash Point ASTM D92 570°F 2,000 hours.
QuinSyn Plus Applications
Effective on orders entered on December 1, 2000 and QuinSyn Plus is suited for use in rotary screw air
later, Quincy Compressor began offering our new compressors operating in harsh service conditions where
extended life synthetic fluid, QuinSyn Plus. QuinSyn the fluid is exposed to higher temperatures for extended
Plus is an optional factory fill for rotary screw periods of time. Fluid thermostat temperature settings
compressors. Machines ordered with QuinSyn Plus as can be elevated to assist in reducing water content in the
the factory fill will be eligible for a five-year extended fluid in high humidity applications. Please consult
airend warranty. Quincy Service Department for any thermostat changes.
QuinSyn Plus is an ISO 46 viscosity fluid with an 8,000 Disposal

hour life under normal operating conditions (exact fluid
life is determined by the fluid analysis program). It is a QuinSyn Plus is considered nonhazardous waste.
synthetic hydrocarbon/ester fluid. Disposal of this fluid should be done in accordance with
Local, State, and Federal regulations. Should condensate
QuinSyn Plus is totally compatible with QuinSyn. need to be treated, Quincy’s QIOW fluid/water separators
Machines currently running with QuinSyn fluid can be are required.
topped off with QuinSyn Plus with no adverse effects.
Fluid Analysis Program
Some advantages of QuinSyn plus are:
• Superior demulsability (ability to separate from QuinSyn Plus fluid is included in Quincy’s fluid analysis
water) program.
• Less susceptible to varnish
• Extremely low volatility
• Excellent corrosion protection NOTICE!
• Outstanding low temperature properties To maintain extended warranty compliance, fluid
• Exceptional thermal stability samples of QuinSyn Plus must be sent to Quincy
• Excellent oxidative stability Compressor Fluid Analysis a minimum of every
• Better gas-fluid separation 2,000 hours.
Typical Properties of QuinSyn Plus ISO 46
Viscosity @ 100°F ASTM D445 46.0 cSt.

Viscosity @ 210°F ASTM D445 7.5 cSt.
Viscosity Index ASTM D2270 127
Specific Gravity 60/60 0.89
Flash Point ASTM D92 475°F
Pour Point -58°F
QuinSyn Fluids QuinSyn
QuinSyn F QuinSyn is a Polyalphaolefin (PAO) type synthetic fluid.

Effective November 1, 2000, QuinSyn Compressor
QuinSyn F is Quincy’s food grade fluid, suitable in Fluid is no longer available as a factory fill option.
applications where there may be incidental food contact. QuinSyn is still available in aftermarket pails, drums and
Compliant with FDA 21 CFR 178.3570 (Lubricants With kits. Extended warranties are not available with the use
Incidental Food Contact), QuinSyn F is authorized by the of QuinSyn, except on compressors shipped prior to June
USDA with an H-1 rating for use in federally inspected 1, 2000.
meat and poultry plants. Since the fluid is viewed as a
possible indirect food additive, the limit for food contact Fluid Life
is 10 ppm. Near white in color and low in volatility,
QuinSyn F is ideal for clean service. A five-year QuinSyn F and QuinSyn IV provide an expected life of
extended warranty is available with the use of QuinSyn 4,000 hours at normal operating conditions. The
F. expected life of QuinSyn is 8,000 hours or one year
(whichever occurs first) at normal operating conditions.
QuinSyn IV
Disposal
QuinSyn IV is a custom-blended Polyalphaolefin (PAO)
partial synthetic hydrocarbon fluid giving improved QuinSyn products are considered nonhazardous under the
lubrication at high and low temperatures, reduced OSHA Hazard Communication Standard 21 CFR
volatility, good chemical inertness and hydrolytic 1910.1200. They carry no hazardous labels or warnings
stability, and compatibility with mineral oils and under that standard. Should condensate need to be
equipment designed for use with mineral oils. QuinSyn treated, Quincy’s QIOW fluid/water separators are
IV is a long life fluid formulated especially for flooded required.
screw compressors. The fluid, clear with a green tint, is
available on all flooded compressors as a factory fill
option. Extended warranties are not available with the
use of QuinSyn IV.
Typical Properties of QuinSyn Fluids
Tests QuinSyn F QuinSyn IV QuinSyn

Viscosity @ 100°C ASTM D445 43.0 cSt. 45.0 cSt. 43.0 cSt.
Viscosity @ 210°C ASTM D445 7.5 cSt. 7.3 cSt. 7.5 cSt.
Viscosity Index ASTM D2270 139 108 139
Flash Point ASTM D92 495°F 455°F 514°F
Fire Point ASTM D92 560°F 498°F 554°F
Pour Point -76°F <-35°F -65°F
Specific Gravity 60/60 0.83 0.85 0.83
Color* Water white/White Clear/Green Pale Blue
*Changes to color will occur during operation.
QuinSyn Flush Typical Properties of QuinSyn Flush

QuinSyn Flush is a specially formulated synthetic fluid Viscosity @ 100°F ASTM D445 43.3 cSt.
capable of dissolving varnish and solubilizing sludge Viscosity @ 210°F ASTM D445 5.6 cSt.
from lubricating systems while they are operating. Viscosity Index 65
QuinSyn Flush contains oxidation and rust inhibitors, and Flash Point ASTM D92 444°F
can be used as a short-term fluid (for a maximum of 500 Fire Point ASTM D92 520°F
hours). It is fully compatible with mineral oils and Pour Point –45°F
QuinSyn synthetic fluids, and is highly recommended for Specific Gravity 60/60 0.965
use as a flushing fluid when converting to QuinSyn PG
from QuinSyn or QuinSyn IV.
Applications
Cleaning fluid for removal of varnish, dirt and oxidized

fluid from compressor fluid systems.
Flushing fluid when changing from other fluids to

QuinSyn fluids.
This page updated 02/19/04.

Cleaning and Flushing With QuinSyn Flush Varnished Machines
Normal Machines Always clean slightly varnished machines using mineral

oils or PAO fluids with QuinSyn Flush using the
Flushing clean machines presently using: following procedure:
A. Mineral Oils - Drain thoroughly as in (A) and fill with QuinSyn Flush.
Drain compressor thoroughly while hot including all Run the machine for 300 hours and take a fluid sample.
the low areas. Shut down and lockout the machine. Send fluid sample to Quincy Compressor Fluid Analysis
Detach lines and drain. Inspect machine; if clean, to determine if further flushes are needed. Continue
change filters and separator elements and proceed as compressor operation until results of fluid analysis are
follows: reported. Drain or continue operation as advised by fluid
analysis.
Fill with QuinSyn Flush and run machine until
it reaches normal operating temperature. Drain Always clean medium to heavily varnished machines
and refill with a fresh charge of the QuinSyn using mineral oils or PAO fluids with QuinSyn Flush
fluid selected for your machine. Send a fluid using the following procedure:
sample to Quincy Compressor Fluid Analysis at
200 hours. Drain thoroughly as in (A) and fill with QuinSyn Flush.
Run the machine for 300 hours and take a fluid sample.
B. Polyalklene glycols (PAG) or Silicone - Send fluid sample to Quincy Compressor Fluid Analysis
Drain compressor thoroughly as in (A). Fill to determine if further flushes are needed. Run the flush
machine with QuinSyn Flush and run for 500 hours. for an additional 300 hours. Drain thoroughly as in (A)
Send a fluid sample to Quincy Compressor Fluid and inspect the compressor. If clean, flush with another
Analysis. Flush may need to be repeated several half charge of QuinSyn Flush and run for 30 minutes.
times. Analysis will determine if further flushes are Drain completely. Change filters and separator elements
needed. and fill with a fresh charge of the QuinSyn fluid selected
for your machine. Send fluid sample to Quincy
Fill with the QuinSyn fluid selected for your Compressor Fluid Analysis at 200 hours.
machine. Send a fluid sample to Quincy
Compressor Fluid Analysis at 200 hours. Extremely varnished machines should not be put back
into service until mechanically or chemically cleaned.
After proper cleaning, fill with a fresh charge of the
QuinSyn fluid selected for your machine. Send fluid
sample to Quincy Compressor Fluid Analysis at 200
hours.
Converting to QuinSyn PG determine if further flushing is needed. Continue

operating compressor until the results of fluid analysis
Normal Machines are known. Drain or continue to run compressor as
advised by the fluid analysis report.
Flush clean machines presently using QuinSyn or
QuinSyn IV before converting them to QuinSyn PG. NOTICE!
More than one flush may be required to remove
Drain compressor thoroughly while hot, including all the varnish build-up and reduce the TAN to an
low areas, fluid lines and fluid cooler. Fill with QuinSyn acceptable level. It may be necessary to change
Flush and run compressor until it reaches normal the fluid filter more frequently while the machine
operating temperatures. Shut down and lockout the is being cleaned.
machine. Drain all the QuinSyn Flush and discard in
accordance with all local, state and federal disposal
regulations. Change the separator and all the filters on If advised to refill with another charge of QuinSyn Flush,
the compressor. Refill the reservoir and system with a run compressor until it reaches normal operating
full charge of QuinSyn PG. temperature. Shut down and lockout the machine. Drain
all of the original charge of the QuinSyn Flush and
NOTICE! discard in accordance with all local, state and federal
If all the previous fluid is not removed from the disposal regulations. Refill with a fresh charge of
compressor, excessive foam may be visible in the QuinSyn Flush and change the fluid filters. Run
fluid level sightglass. If this occurs, repeat the compressor for 300 hours. Take a fluid sample and send
flushing procedure. to Quincy Compressor Fluid Analysis to determine if
further flushing is needed. Proceed as instructed by the
Varnished Machines fluid analysis report.
Flush varnished machines presently using QuinSyn or If advised to drain the QuinSyn Flush, run compressor
QuinSyn IV before converting them to QuinSyn PG. until it reaches normal operating temperature. Shut down
and lockout the machine. Drain the QuinSyn Flush and
Drain compressor thoroughly while hot, including all the discard in accordance with all local, state and federal
low areas, fluid lines and the fluid cooler. Fill with disposal regulations. Change the separator and fluid
QuinSyn Flush and run for 300 hours. Take a fluid filters on the compressor and refill with a full charge of
sample and send to Quincy Compressor Fluid Analysis to the QuinSyn PG.
Converting to QuinSyn XP Converting to QuinSyn Plus
Normal Machines Normal Machines
A. Any QuinSyn fluid - No flush required. Drain A. Any QuinSyn fluid (except QuinSyn PG) - No flush
Compressor thoroughly while hot, including all the required. Drain Compressor thoroughly while hot,
low areas, fluid lines and the fluid cooler. Shut including all the low areas, fluid lines and the fluid
down and lockout the machine. Change the cooler. Shut down and lockout the machine.
separator and all the filters on the compressor. Change the separator and all the filters on the
Refill the reservoir and system with a full charge of compressor. Refill the reservoir and system with a
QuinSyn XP. full charge of QuinSyn Plus.
B. Mineral Oils - Drain compressor thoroughly while B. Mineral Oils and QuinSyn PG - Drain compressor
hot including all the low areas. Shut down and thoroughly while hot including all the low areas.
lockout the machine. Detach lines and drain. Shut down and lockout the machine. Detach lines
Inspect machine; if clean, change filters and and drain. Inspect machine; if clean, change filters
separator elements. Fill with QuinSyn Flush and and separator elements. Fill with QuinSyn Flush
run machine until it reaches normal operating and run machine until it reaches normal operating
temperature. Drain and refill with a fresh charge of temperature. Drain and refill with a fresh charge of
new QuinSyn XP. Send a fluid sample to Quincy new QuinSyn Plus. Send a fluid sample to Quincy
Compressor Fluid Analysis at 200 hours. Compressor Fluid Analysis at 200 hours.
Varnished Machines Varnished Machines

For slightly to extremely varnished machines using For slightly to extremely varnished machines using
mineral oils or PAO fluids, flush the compressor with mineral oils or PAO fluids, flush the compressor with
QuinSyn Flush following the procedures outlined on QuinSyn Flush following the procedures outlined on
page 35. page 35.
Converting to QuinSyn
QuinSyn fluids are compatible with the materials and

elastomers used in mineral oil systems. Converting your
compressor from mineral oil to QuinSyn or QuinSyn IV
may be as easy as a simple flush to remove any sludge
and varnish present. Emphasis must be placed on
draining after each step. Contaminants left in the
compressor after flushing have a direct effect on the
fluid’s life. Once the oxidized material (varnish) is
dissolved in the QuinSyn Flush, the cleaner and varnish
must be removed from the compressor and system parts
(particularly in areas like filters, coolers and piping, etc.).
See your Quincy Compressor Distributor to assist in the
evaluation of your compressor.
NOTICE!
If converting to QuinSyn F from any QuinSyn
fluid contact the Quincy Service Department.
Quincy
Compressor Fluid Analysis
2300 James Savage Road
Midland, Michigan 48642-6535
UNDENIABLY THE WORLD’S FINEST COMPRESSORS
Sampling Procedures
Preferred sample location is the fluid filter. If unable to take sample from fluid filter, proceed as follows:
1. Shutdown and lockout compressor.

2. Relieve pressure in reservoir.
3. Remove plug from reservoir drain line.
4. Drain water from reservoir and discard in approved manner.
5. Fill sample bottle with fluid.
6. Close valve and replace plug in drain line.
7. Return compressor to service and check fluid level during operation. Service with fluid as required.
Using fluid filter sample valve, proceed as follows:
1. Open valve, drain 2-4 ounces of fluid from filter and discard in an approved manner.
2. Fill sample bottle.
3. Close valve.
After collecting sample from either of the above methods:
1. Fill out information label completely.
Be certain to provide all information as to possible hazards related to a given sample. If this situation exists, all
information shall be clearly marked on the sample bottle label.
2. Attach Sample Bottle Label to the bottle and put bottle in mailer.
3. Place Shipping Label on the outside of the mailer and send it by UPS.
FROM: ___________________________________________ FROM:
Customer Fax # ____________________________________

Model No. _______________ Serial No.
Fluid ____________________ Sample Date _____________ TO:Quincy Compressor Fluid Analysis
Hours on Fluid ___________ Hours on Machine ________ 2300 James Savage Road
Distributor ________________________________________ Midland, MI 48642-6535
Sample From ❏ Reservoir ❏ Filter
Sample Bottle Label Shipping Label
Note: A fluid sample valve kit is available from Quincy Compressor. Contact the Service
Department and ask for part number 143286.
PRODUCT ANALYSIS REPORT

Quincy (a)
Compressor Fluid Analysis
2300 James Savage Road, Midland, MI 48642
(b)
UNDENIABLY THE WORLD’S FINEST COMPRESSORS
Customer (d)
Comp. Mfr. (e)
(c)
Fluid Type (f)
Serial Number (g)
Model Number (h)
Hrs. on Fluid (i)
Hrs. on Machine (j)
Sample Date (k)
I.D. #
Evaluation: (1)
Physical Properties* Results (m)

Water by Viscosity TAN Particle Count ISO Antioxidant
Karl Fischer 40° C Total 5 10 15 20 25 30 35 40 Code Level
(ppm) (cSt) Acid # um um um um um um um um
* Property values, not to be construed as specifications
Spectrochemical Analysis (n)

Sample Values below are in parts per million (ppm)
Date Silver Alum. Chrom Copp. Iron Nickel Lead Tin Titan Vanad Bari Calc. Mag. Mol. Sod. Phos. Sili. Zinc
(Fluid Hours) (Ag) (Al) (Cr) (Cu) (Fe) (Ni) (Pb) (Sn) (Ti) (V) (Ba) (Ca) (Mg) (Mo) (Na) (P) (Si) (Zn)
Thank you for this opportunity to provide technical assistance to your company. If you have any questions about this report please contact
us at 1-800-637-8628 or fax 1-517-496-2313.
CC List
*means this parameter not tested
Accuracy of recommendations is dependant on representative fluid

samples and complete correct data on both unit and fluid.
Understanding the Analysis Report i) HOURS ON FLUID - These are the actual hours
that the QuinSyn fluid has been in the unit since the
Reference page 40 for a copy of a blank analysis report. last fluid change.
a) REPORT DATE - The date that the fluid was j) HOURS ON MACHINE - This is the total hours on
analyzed. the compressor hourmeter.
b) REPORT NUMBER - The assigned number to this k) SAMPLE DATE - The date that the sample was
report. taken from the compressor.
c) CUSTOMER ADDRESS - The name and address of NOTICE!

person that this report is being mailed to. This Items c) through k) are information provided by
information is being taken from the sample bottle as the service person supplying the fluid for analysis.
it is received. Incomplete or incorrect information will affect
the report’s accuracy.
d) CUSTOMER - The owner of the unit that sample
came from.
l) EVALUATION - This is a brief statement made by
e) COMPRESSOR MANUFACTURER - Brand of the technician performing the actual fluid analysis.
compressor sample taken from. This statement addresses the condition of the fluid
and filter. This statement will also note any
f) FLUID TYPE - This should always be one of the problems that need attention.
fluids listed in the previous section.
m)PHYSICAL PROPERTIES RESULTS - Particle
g) SERIAL NUMBER - The unit serial number of the size is measured in microns. See Fluid Parameters
Quincy compressor the fluid sample was taken on pages 42-43.
from.
n) SPECTROCHEMICAL ANALYSIS - See Fluid
h) MODEL NUMBER - The model number of the Parameters on pages 42-43.
Quincy compressor that the fluid sample was taken
from.
FLUID PARAMETERS
QuinSyn PG, QuinSyn XP & QuinSyn Plus
Property Units Test Method Fluid Type New Fluid Marginal Unacceptable
Viscosity cSt ASTM D-445 QuinSyn PG 45-55 41,61 <41, >61 (1)
40°C QuinSyn XP 58-75 50, 85 <50, >85 (1)
QuinSyn Plus 42-51 38, 56 <38, >56 (1)
Acid No. mg KOH/gm ASTM D-947 QuinSyn PG <0.2 0.7-0.9 >1 (1)
TAN QuinSyn XP <0.2 3-4 >4 (1)
QuinSyn Plus <0.2 1.7-1.9 >2.0 (1)
ADDITIVE METALS
Barium PPM Plasma Emission QuinSyn PG 375-550 150 <10 (1)
QuinSyn XP 0 5-20 >20
QuinSyn Plus 0 5-20 >20
Calcium PPM Plasma Emission All 0 5-20 >20
Magnesium PPM Plasma Emission All 0 5-20 >20
Molybdenum PPM Plasma Emission All 0 5-20 >20
Sodium PPM Plasma Emission QuinSyn PG 0 40-50 >100
QuinSyn XP 0 40-50 >100
Phosphorus PPM Plasma Emission QuinSyn PG 0 5-20 >20
QuinSynXP <50 5-20 0
Zinc PPM Plasma Emission All 0 100-200 >200
WEAR METALS
Silver PPM Plasma Emission All 0 5-10 >10
Aluminum PPM Plasma Emission All 0 5-10 >10
Chromium PPM Plasma Emission All 0 5-10 >10
Copper PPM Plasma Emission All 0 5-10 >10
Iron PPM Plasma Emission All 0 5-10 >10
Nickel PPM Plasma Emission All 0 5-10 >10
Lead PPM Plasma Emission All 0 5-10 >10
Tin PPM Plasma Emission All 0 5-10 >10
Titanium PPM Plasma Emission All 0 5-10 >10
Vanadium PPM Plasma Emission All 0 5-10 >10
OTHER
Silicon PPM Plasma Emission All 0 10-15 >15
Water PPM Karl Fisher QuinSyn PG <2000 NOT REPORTED
QuinSynXP <800 NOT REPORTED
QuinSyn Plus <800 NOT REPORTED
Antioxidant % HPCL All 95% min. NOT REPORTED
(1) The fluid will be condemned based on these parameters.
FLUID PARAMETERS
QuinSyn, QuinSyn IV & QuinSyn F
Property Units Test Method Fluid Type New Fluid Marginal Unacceptable
Viscosity cSt ASTM D-445 QuinSyn 40-48 38, 52 <38, >52 (1)
40°C QuinSyn IV 40-48 38, 52 <38, >52 (1)
QuinSyn F 41-51 39, 56 <39, >56 (1)
Acid No. mg KOH/gm ASTM D-947 All 0.2 0.8-0.9 >1 (1)
TAN
ADDITIVE METALS
Barium PPM Plasma Emission All 0 5-20 >20
Calcium PPM Plasma Emission All 0 5-20 >20
Magnesium PPM Plasma Emission All 0 5-20 >20
Molybdenum PPM Plasma Emission All 0 5-20 >20
Sodium PPM Plasma Emission All 0 5-20 >20
Phosphorus PPM Plasma Emission All 0 5-20 >20
Zinc PPM Plasma Emission All 0 100-200 >200
WEAR METALS
Silver PPM Plasma Emission All 0 5-10 >10
Aluminum PPM Plasma Emission All 0 5-10 >10
Chromium PPM Plasma Emission All 0 5-10 >10
Copper PPM Plasma Emission All 0 5-10 >10
Iron PPM Plasma Emission All 0 5-10 >10
Nickel PPM Plasma Emission All 0 5-10 >10
Lead PPM Plasma Emission All 0 5-10 >10
Tin PPM Plasma Emission All 0 5-10 >10
Titanium PPM Plasma Emission All 0 5-10 >10
Vanadium PPM Plasma Emission All 0 5-10 >10
OTHER
Silicon PPM Plasma Emission All 0 10-15 >15
Water PPM Karl Fisher All <100 200 >200
Particle Count Microns Hiac Royco All ISO CODE X/20
Antioxidant % Liquid Chromatography All 95 NOT REPORTED
(1) The fluid will be condemned based on these parameters.
• Differential Pilot Valve

• Pressure Switch
• Water Temperature Regulating Valve
(Water-cooled units Only)
• Drive Coupling Alignment
Differential Pilot Valve Pressure Switch
The pressure switch determines what pressure the

compressor will load and unload. Standard factory
WARNING! settings are 110 PSIG cut-in, 125 cut-out. If a lower
setting is desired, adjust the differential pilot valve first
Never adjust the pressure higher than the factory and set the pressure switch cut-out point to 15 PSIG over
setting. Death or serious injury and compressor the desired full load pressure. The range adjustment is
or property damage could result. made by turning the screw clockwise to increase the cut-
in/cut out pressure.
Open a manual vent valve to allow the compressor to
exhaust air to the outside and start the unit. By manual
regulation, slowly close the valve, allowing the unit to
Water Temperature Regulating Valve
build air pressure to the desired modulation point and
hold (110 PSIG standard). Adjust the screw on the
(Water-cooled units Only)
bottom of the differential pilot valve so that a slight
stream of air can be felt coming from the orifice adjacent The water temperature regulating valve senses fluid
to the adjustment screw. temperature and opens or closes, regulating water flow
from the unit. It is factory set to maintain 180°F
When this air is felt, air is beginning to pass through the discharge temperature. Due to different incoming water
pilot valve to the air cylinder on the inlet valve, causing temperatures and/or pressures at each location valve
the valve to modulate toward its closed position, thereby adjustment should be checked during start-up to maintain
reducing the volume of air being compressed. 180°F discharge temperature. To increase fluid
temperature, decrease water flow by turning the
To raise the pressure, turn the adjusting screw in adjustment screw clockwise. To decrease fluid
(clockwise). To lower the pressure, turn the screw out temperature, increase water flow by turning the
(counter clockwise). Maximum full load pressure is 110 adjustment screw counter clockwise.
PSIG for standard QSI units. Minimum full load pressure
with modulation and standard controls is 75 PSIG.
Drive Coupling Alignment 1) Tag and lock out all power to the unit.
2) Remove coupling guard.
QSI 245-750 3) Unbolt and remove one-half (1/2) of the flexible
element. Leave the remaining half bolted to both
These QSI units are direct coupled between the airend steel hubs.
and the drive motor through the use of a transition piece. 4) Using one of the existing 3/8” bolt holes in the
Realignment of the coupling is not necessary. compressor hub, attach a dial indicator mounting
stud or bolt in firmly.
QSI 1000-1500 5) Attach a dial indicator to the mount with the
necessary hardware to allow the indicator plunger to
It is necessary to check and correct the coupling contact the motor hub.
alignment between the compressor and the motor. This
service is vital to the life of the motor and compressor NOTICE!
bearings and must be performed after the unit has been Four viewpoints need to be checked. Angular and
installed in its final location and prior to start-up. If the parallel, as view from the top. Angular and
unit is ever moved from its original site, the alignment parallel, as viewed from the side.
must be checked again. The QSI series compressors
utilize a two piece flexible element bolted to steel hubs Do not operate the unit without both coupling halves and
on the compressor motor shafts. The following steps will guards in place.
ensure a properly aligned coupling:
Correcting Angular Misalignment-Side View 5) Divide measurement “A” by measurement “B”.
1) With the indicator point on the face of the motor 6) Multiply the result from step 5 by the indicator
half, zero the indicator. reading “C” to determine the amount of shim to be
placed under either the front feet or the rear feet of
2) Rotate the entire assembly 180° or one-half (1/2) the motor to correct misalignment.
turn. Note the indicator reading. This reading is
referred to as “C” in the formula and example Example (refer to Figure 8-1):
shown.
A = 5”, B = 4”, C = +0.028
3) Measure the distance from center to center between
the motor feet. This will be referred to as “A”. Because C is a positive reading, the distance between the
coupling halves is greater at the top.
4) Measure the O.D. of the coupling. This will be
referred to as “B”. 5/4 x 0.028 = 0.035 required shims
AIREND B MOTOR
A = DISTANCE BETWEEN FEET

B = COUPLING DIAMETER A
C = INDICATOR READING
A/B x C = REQUIRED SHIMS
Figure 8-1. Angular Misalignment-Side View
Angular Misalignment Viewed From the Top Parallel Misalignment Viewed from the Top
1) Mount the dial indicator on the compressor coupling 1) Mount the dial indicator on the compressor coupling
half so that it reads from the face of the motor half so that it reads from the outside surface of the
coupling half. motor coupling half.
2) Position the indicator on the side of the coupling. 2) Position the indicator on the side of the coupling.
3) Rotate the coupling halves together, 180° in the 3) Rotate the coupling halves together, 180° in the
direction of the compressor rotation. The indicator direction of the compressor rotation. The indicator
reading in this position is the amount of angular reading in this position is the amount of parallel
misalignment. misalignment.
4) Loosen the motor mounting bolts and move the 4) Loosen the motor mounting bolts and move the
motor slightly with a pry bar or soft mallet so that motor slightly with a pry bar or soft mallet so that
when step C is performed, the indicator reading is when step C is performed, the indicator reading is
within machine specification. within machine specifications.
NOTICE! NOTICE!
Do not lubricate capscrew threads. If capscrews Always recheck all measurements since one
are used, apply thread-locking adhesive. These alignment procedure may effect another.
are special bolts. Do not substitute. Reinstall the other coupling half and torque all
mounting bolts. Before placing the unit in
operation, replace the drive guard and clear the
area of all tools.
Drive Coupling Specifications
Model* Alignment Angular Specifications Element Bolt Element Bolt

Parallel Size Torque
1000-1500 0.005” 0.010” 1/2” 70 ft/lbs.
*Standard 110 PSIG models only
Probable Causes: Corrective Action:
Failure to Start:
POWER NOT TURNED “ON” TURN THE POWER “ON” BY CLOSING THE MAIN
DISCONNECT SWITCH OR CIRCUIT BREAKER.
BLOWN CONTROL CIRCUIT FUSE REPLACE FUSE. FIND AND CORRECT CAUSE.
SAFETY CIRCUIT SHUTDOWN RESULTING FROM HIGH CORRECT THE SITUATION IN ACCORDANCE WITH THE
DISCHARGE AIR TEMPERATURE INSTRUCTION IN THE “HIGH DISCHARGE AIR
TEMPERATURE” SECTION OF THIS TROUBLESHOOTING
GUIDE. RESTART THE COMPRESSOR.
THERMAL OVERLOAD RELAYS TRIPPING CORRECT THE CAUSE OF THE OVERLOADED

CONDITION, RESET OVERLOAD RELAY AND PRESS THE
START BUTTON.
LOW VOLTAGE ASK THE POWER COMPANY TO MAKE A VOLTAGE

CHECK AT YOUR ENTRANCE METER, THEN COMPARE
THAT READING TO A READING TAKEN AT THE MOTOR
TERMINALS. USE THESE TWO READINGS AS A BASIS
FOR LOCATING THE SOURCE OF LOW VOLTAGE.
FAULTY START SWITCH CHECK THE SWITCH FOR MALFUNCTION OR LOOSE

CONNECTIONS.
POWER FAILURE CHECK POWER SUPPLY TO THE UNIT.
FAULTY CONTROL RELAY REPLACE THE RELAY.
LOOSE WIRE CONNECTIONS CHECK ALL WIRING TERMINALS FOR CONTACT AND
TIGHTNESS.
FAULTY HIGH AIR TEMPERATURE SWITCH CHECK H A T SWITCH. CONTACT A QUALIFIED

SERVICE TECHNICIAN FOR REPAIRS.
FAULTY TRANSFORMER CHECK SECONDARY VOLTAGE ON TRANSFORMER.
Unscheduled Shutdown:
HIGH DISCHARGE AIR TEMPERATURE CORRECT THE SITUATION IN ACCORDANCE WITH THE
INSTRUCTION IN THE “HIGH DISCHARGE AIR
TEMPERATURE” SECTION OF THIS TROUBLESHOOTING
GUIDE. RESTART THE COMPRESSOR.
THERMAL MOTOR OVERLOAD RELAYS TRIPPING CORRECT THE CAUSE OF THE MOTOR OVERLOADED
CONDITION, RESET THE OVERLOAD RELAY AND PRESS
THE RESET BUTTON.
POWER FAILURE CHECK POWER SUPPLY AND TRANSFORMER FUSES.
FAULTY HAT SENSORS CONTACT A QUALIFIED SERVICE TECHNICIAN FOR

REPAIRS.
LOOSE WIRE CONNECTIONS CHECK ALL WIRING TERMINALS FOR CONTACT AND
TIGHTNESS.
FAULTY CONTROL RELAY REPLACE RELAY.
Thermal Overload Relays Tripping:
EXCESSIVE DISCHARGE PRESSURE LOWER FULL LOAD PRESSURE SETTING AT CONTROL

PANEL.
LOW VOLTAGE CHECK VOLTAGE AND AMPERAGES WHILE OPERATING

AT FULL LOAD PRESSURE.
LOOSE OVERLOAD CONNECTION TIGHTEN MOUNTING SCREWS ON THERMAL

OVERLOAD.
INCORRECT THERMAL OVERLOAD RELAY SETTING CHECK MOTOR NAMEPLATE AND COMPARE TO
OVERLOAD RELAY SETTING.
LOOSE MOTOR OR STARTER WIRING CHECK ALL CONNECTIONS FOR TIGHTNESS.
FAULTY MOTOR CHECK MOTOR STARTER WIRING BEFORE REMOVING

MOTOR. REMOVE MOTOR AND HAVE TESTED AT
MOTOR MANUFACTURER REPAIR CENTER.
Low Air Delivery:
PLUGGED AIR INTAKE FILTER ELEMENT CLEAN AIR FILTER ELEMENT OR REPLACE WITH NEW
ELEMENT.
EXCESSIVE LEAKS IN THE SERVICE LINES CHECK SERVICE LINES FOR LEAKS WITH SOAP SUDS.
REPAIR AS NECESSARY.
INLET VALVE NOT FULLY OPEN CHECK FOR BUILD UP OR GUMMING OF SHAFT.
RESTRICTED FLUID FLOW CHECK FLUID FILTER FOR PLUGGING.
Low Receiver Pressure:
EXCESSIVE AIR DEMAND REEVALUATE AIR DEMAND. INSTALL ADDITIONAL

COMPRESSORS AS NEEDED.
EXCESSIVE LEAKS IN THE SERVICE LINES CHECK SERVICE LINES FOR LEAKS WITH SOAP SUDS.
REPAIR AS NECESSARY.
INLET VALVE NOT FULLY OPEN CORRECT IN ACCORDANCE WITH THE INSTRUCTIONS
IN “INLET VALVE NOT OPENING OR CLOSING IN
RELATION TO AIR DEMAND” SECTION OF
TROUBLESHOOTING GUIDE.
PLUGGED AIR INTAKE FILTER REPLACE AIR FILTER ELEMENT.
DIFFERENTIAL PILOT VALVE NOT SET CORRECTLY ADJUST DIFFERENTIAL PILOT VALVE TO ACHIEVE
DESIRED MODULATION RANGE.
AIR PRESSURE SWITCH NOT SET CORRECTLY ADJUST AIR PRESSURE SWITCH TO ACHIEVE DESIRED
CUT-IN AND CUT-OUT PRESSURE.
FAULTY RECEIVER PRESSURE GAUGE CHECK AND REPLACE AS NECESSARY.
High Receiver Pressure:
AIR PRESSURE SWITCH NOT SET CORRECTLY ADJUST AIR PRESSURE SWITCH TO ACHIEVE DESIRED
CUT-IN AND CUT-OUT PRESSURE. ENSURE UNLOAD
PRESSURE DOES NOT EXCEED MAXIMUM OPERATING
PRESSURE.
INLET VALVE NOT CLOSING AT LOWER AIR DEMAND CORRECT IN ACCORDANCE WITH INSTRUCTION ON
“INLET VALVE NOT OPENING OR CLOSING IN
RELATION TO AIR DEMAND” SECTION OF THIS
BLOWDOWN VALVE NOT RELIEVING RECEIVER CHECK CONTROL SOLENOID AND BLOWDOWN VALVE.
PRESSURE
High Discharge Air Temperature and/or High Fluid Injection Temperature:
NOT ENOUGH COOLING WATER FLOWING THROUGH CLEAN COOLER. CHECK WATER SYSTEM FOR
COOLER (WATER-COOLED MODELS ONLY) POSSIBLE RESTRICTIONS, INCLUDING WATER
TEMPERATURE REGULATING VALVE. CLEAN OR
ADJUST, IF NECESSARY.
INADEQUATE CIRCULATION OF COOLING AIR AT THE CHECK LOCATION OF COOLER AND ASSURE NO
COOLER (AIR-COOLED MODELS ONLY) RESTRICTION TO FREE CIRCULATION OF COOLING AIR.
CHECK COOLER FIN AND CLEAN AS NECESSARY.
LOW FLUID LEVEL IN RESERVOIR ADD FLUID TO RECOMMENDED LEVEL. CHECK FLUID
SYSTEM FOR LEAKS.
CABINET PANELS REMOVED REPLACE ALL PANELS, ENSURE ALL SEALING

SURFACES AND MATERIALS ARE SATISFACTORY.
COOLER PLUGGED CLEAN COOLER, FIND AND CORRECT CAUSE OF

CONTAMINATION.
FLUID FILTER PLUGGED REPLACE FLUID FILTER ELEMENT(S).
High Discharge Air Temperature and/or High Fluid Injection Temperature (continued):
EXCESSIVE AMBIENT TEMPERATURES MAXIMUM AMBIENT FOR PROPER OPERATION IS

LISTED IN DATA SHEET. VENTILATE ROOM OR
RELOCATE COMPRESSOR.
INCORRECT FAN ROTATION CORRECT ROTATION IS WITH THE FAN PUSHING THE
AIR THROUGH THE COOLER. REVERSE MOTOR
STARTER LEADS L1 AND L2.
IMPROPER FLUID USE RECOMMENDED FLUIDS ONLY. REFER TO

“COMPRESSOR FLUIDS” SECTION OF THIS MANUAL.
CLOGGED AIR FILTER CLEAN OR REPLACE AS NECESSARY.
FAULTY THERMAL VALVE REPAIR OR REPLACE AS NECESSARY.
FAULTY GAUGES CHECK AND REPLACE AS NECESSARY.
AIREND FAILURE CONTACT AN AUTHORIZED QUINCY DISTRIBUTOR.
Frequent Air/Fluid Separator Clogging:
FAULTY AIR FILTER OR INADEQUATE FILTER FOR THE IF FAULTY AIR FILTER ELEMENTS, REPLACE THEM. IF
ENVIRONMENT AIR FILTER IS INADEQUATE FOR THE ENVIRONMENT,
RELOCATE THE INTAKE AIR TO A CLEAN SOURCE.
FAULTY FLUID FILTER REPLACE FLUID FILTER ELEMENT.
FLUID BREAKDOWN CORRECT IN ACCORDANCE WITH THE INSTRUCTION IN

“FLUID BREAKDOWN” SECTION OF THE
INCORRECT FLUID SEPARATOR ELEMENT USE GENUINE QUINCY REPLACEMENT ELEMENTS

ONLY.
EXTREME OPERATING CONDITIONS SUCH AS HIGH OPERATE COMPRESSOR AT RECOMMENDED

COMPRESSOR DISCHARGE TEMPERATURES, HIGH RESERVOIR PRESSURE AND DISCHARGE AIR
AMBIENT TEMPERATURE WITH HIGH HUMIDITY AND TEMPERATURE.
HIGH RESERVOIR PRESSURE
Frequent Air/Fluid Separator Clogging (continued):
MIXING DIFFERENT GRADES OR TYPES OF FLUIDS DO NOT MIX DIFFERENT GRADES OR TYPES OF FLUID.
DO NOT MIX FLUIDS FROM DIFFERENT
MANUFACTURERS.
INCORRECT FLUID FOLLOW FLUID SPECIFICATIONS AS DESCRIBED IN

“COMPRESSOR FLUIDS” SECTION OF THIS MANUAL.
CHANGE FLUID. SERVICE AIR FILTER AND FLUID

CONTAMINATED FLUID FILTER IN ACCORDANCE WITH THE RECOMMENDED
MAINTENANCE SCHEDULE.
Fluid Discharge Out Blowdown Valve:
TOO HIGH FLUID LEVEL IN RESERVOIR ADJUST FLUID LEVEL TO RECOMMENDED FLUID
LEVEL BY DRAINING THE RESERVOIR. USE FLUID
LEVEL GAUGE AS A GUIDE.
AIR/FLUID RESERVOIR BLOWS DOWN TOO FAST CHECK FOR PROPER BLOWDOWN VALVE SIZE.
INLET VALVE NOT CLOSING COMPLETELY CORRECT IN ACCORDANCE WITH INSTRUCTIONS IN

“INLET VALVE NOT OPENING OR CLOSING IN
TROUBLESHOOTING GUIDE
Frequent Fluid Filter Clogging:
FAULTY INDICATOR REPLACE INDICATOR ASSEMBLY.
INCORRECT FLUID FILTER USE GENUINE QUINCY REPLACEMENT FILTERS ONLY.
FAULTY, INCORRECT OR INADEQUATE AIR FILTER REPLACE AIR FILTER ELEMENT.
FLUID BREAKDOWN SEE FLUID BREAKDOWN SECTION OF THIS

SYSTEM CONTAMINATION CHECK AND CLEAN SYSTEM OF ALL DIRT, CORROSION

AND VARNISH.
Excessive Fluid Consumption:
TOO HIGH FLUID LEVEL IN THE RECEIVER ADJUST FLUID LEVEL TO RECOMMENDED FLUID
LEVEL BY DRAINING THE RESERVOIR. USE FLUID
LEVEL GAUGE AS A GUIDE.
PLUGGED SCAVENGER LINE CLEAN SCAVENGER LINE ORIFICE AND TUBE.
HIGH DISCHARGE TEMPERATURE CORRECT IN ACCORDANCE WITH THE INSTRUCTIONS

IN “HIGH DISCHARGE AIR TEMPERATURE” SECTION OF
THIS TROUBLESHOOTING GUIDE.
LOW RESERVOIR PRESSURE WITH FULLY OPEN INLET RESERVOIR PRESSURE SHOULD NOT FALL BELOW 50
VALVE PSIG WHEN RUNNING LOADED. CHECK SYSTEM
CFM REQUIREMENT AND MINIMUM PRESSURE CHECK
VALVE.
FAULTY OR DAMAGED SEPARATOR CHANGE AIR/FLUID SEPARATOR.
LEAK IN FLUID LINES CHECK FOR LEAKS AND CORRECT.
SEAL FAILURE, LEAKS REPLACE SEAL ASSEMBLY AND O-RINGS.
INCORRECT FLUID USE RECOMMENDED FLUIDS ONLY. SEE

COMPRESSOR FLUID SECTION.
Frequent Air Cleaner Clogging:
COMPRESSOR OPERATING IN HIGHLY CONTAMINATED USE REMOTE AIR INTAKE MOUNTING.

ATMOSPHERE
AIR CLEANER NOT ADEQUATE FOR CONDITIONS USE SPECIALIZED AIR FILTER. CONTACT AN
AUTHORIZED QUINCY DISTRIBUTOR.
Inlet Valve Not Opening Or Closing In Relation To Air Demand:
IMPROPER SETTING OF AIR PRESSURE SWITCH OR ADJUST AIR PRESSURE SWITCH TO PROPER SETTING
FAULTY SWITCH OR REPLACE SWITCH, IF FAULTY.
EXCESSIVE MOISTURE IN CONTROL AIR LINE AT AIR SERVICE CONTROL AIR LINE FILTER DAILY.
CYLINDER
IMPROPER FUNCTIONING OF INLET VALVE PISTON CHECK PISTON AND CYLINDER BORE. REPAIR OR
REPLACE AS NEEDED.
JAMMED AIR INLET VALVE ASSEMBLY CHECK AIR INLET VALVE BUSHING AND SHAFT.
CHECK PISTON AND CYLINDER BORE. REPAIR OR
REPLACE AS NEEDED.
FAULTY SOLENOID VALVE REPAIR OR REPLACE AS NECESSARY.
FAULTY SHUTTLE VALVE REPAIR OR REPLACE AS NECESSARY.
LOOSE WIRING CONNECTIONS AT SOLENOID VALVE/ CHECK AND TIGHTEN WIRING TERMINALS.
PRESSURE SWITCH
BROKEN SPRING IN AIR INLET VALVE REPLACE SPRING.
Compressor Does Not Unload When There Is No Air Demand:
INCORRECT AIR PRESSURE SWITCH SETTING ADJUST TO PROPER SETTING.
FAULTY AIR PRESSURE SWITCH REPLACE SWITCH.
FAULTY BLOW DOWN VALVE REPAIR OR REPLACE AS NECESSARY.
FAULTY SOLENOID VALVE REPAIR OR REPLACE AS NECESSARY.
FAULTY DIFFERENTIAL PILOT VALVE REPAIR OR REPLACE AS NECESSARY.
LEAKS IN CONTROL LINES CHECK ALL CONTROL LINE FITTINGS AND TUBINGS.
LEAKS IN SERVICE LINES CHECK LINES BEFORE MPC VALVE.
Compressor Does Not Revert To Load When Service Line Pressure Drops To Reset Pressure:
FAULTY AIR PRESSURE SWITCH REPAIR OR REPLACE AS NECESSARY.
LOOSE WIRING CONNECTION CHECK AND TIGHTEN WIRING TERMINALS.
JAMMED AIR INLET VALVE ASSEMBLY CHECK AND REPAIR AIR INLET VALVE.
FAULTY SOLENOID REPAIR OR REPLACE AS NECESSARY.
FAULTY TIMER CHECK AND REPLACE TIMER.
FAULTY DIFFERENTIAL PILOT VALVE ORIFICE PLUGGED. CLEAN OR REPLACE AS

NECESSARY.
Compressor Will Not Time-out Or Shut Down When Unloaded (Auto/Dual Only):
FAULTY TIMER CHECK AND REPLACE AS NECESSARY.
LEAKS IN CONTROL LINES CHECK AND REPAIR ANY LEAKS.
LEAKS IN SERVICE LINES CHECK PLANT AIR DISTRIBUTION SYSTEM FOR LEAKS.
FAULTY AIR PRESSURE SWITCH REPAIR OR REPLACE AS NECESSARY.
FAULTY AIR PRESSURE SENSORS REPLACE AS NECESSARY.
Excessive Water in Plant Air Distribution System:
CLOGGED MOISTURE SEPARATOR/TRAP CLEAN OR REPLACE AS REQUIRED.
INSTALLATION/APPLICATION CHECK OTHER COMPRESSORS ON SAME SYSTEM.
FAULTY COOLER/LEAKS REPLACE COOLER.
Pressure Relief Valve Exhausting:
DIFFERENTIAL PRESSURE REGULATOR NOT SET ADJUST DIFFERENTIAL PRESSURE REGULATOR TO

CORRECTLY OBTAIN DESIRED MODULATION RANGE.
AIR PRESSURE NOT SET CORRECTLY READJUST AIR PRESSURE SWITCH SO THAT THE
COMPRESSOR UNLOADS AT THE DESIRED PRESSURE.
AIR INLET VALVE NOT CLOSING PROPERLY IN CORRECT IN ACCORDANCE WITH THE INSTRUCTION IN
RELATION TO AIR DEMAND “INLET VALVE NOT OPENING OR CLOSING IN
PLUGGED SEPARATOR REPLACE WITH NEW AIR/FLUID SEPARATOR.
FAULTY RECEIVER PRESSURE GAUGE CHECK GAUGE FOR ACCURACY AND REPLACE IF
NECESSARY. ADJUST CONTROL SETTINGS.
FAULTY PRESSURE RELIEF VALVE CHECK PRESSURE RELIEF VALVE FOR CORRECT
PRESSURE SETTING. IF VALVE IS STILL LEAKING,
REPLACE IT.
Excessive Water Content In Fluid:
WATER DRAIN INTERVALS DRAIN WATER AS NEEDED TO REDUCE WATER

CONTENT IN FLUID BELOW200 PPM.
DISCHARGE TEMPERATURE TOO LOW CHECK OPERATION OF THERMOSTATIC VALVE OR

WATER REGULATING VALVE. IF CONDITION
CONTINUES, CONSULT QUINCY SERVICE DEPARTMENT.
Section X- Maintenance Schedule
Interval: Action:
PERIODICALLY/DAILY: MONITOR ALL GAUGES AND INDICATORS FOR

(8 HOURS MAXIMUM) NORMAL OPERATION.
CHECK FLUID LEVEL.
OBSERVE FOR FLUID LEAKS.
OBSERVE FOR UNUSUAL NOISE OR VIBRATION.
DRAIN WATER FROM AIR/FLUID RESERVOIR.
MONTHLY: SERVICE AIR FILTER AS NEEDED. (DAILY OR WEEKLY

IF EXTREMELY DIRTY CONDITIONS EXIST)
CLEAN AFTERCOOLER AND FLUID COOLER FINS.
(AIR-COOLED ONLY)
WIPE ENTIRE UNIT DOWN TO MAINTAIN APPEARANCE.
6 MONTHS OR EVERY 1000 HOURS: TAKE FLUID SAMPLE.

CHANGE FLUID FILTER.
CHECK PRESSURE RELIEF VALVE.
PERIODICALLY/YEARLY: GO OVER UNIT AND CHECK ALL BOLTS FOR

TIGHTNESS.
CHANGE AIR/FLUID SEPARATOR.
CHANGE AIR FILTER.
LUBRICATE MOTORS.
TEST PRESSURE RELIEF VALVE FOR PROPER OPERATION.
CHECK SAFETY (HAT) SHUTDOWN SYSTEM
(CONTACT A QUALIFIED SERVICE TECHNICIAN)
THIS PAGE INTENTIONALLY LEFT BLANK
QSI 220/245 (air-cooled)
QSI 220/245 (water-cooled)
QSI 1175/1250 & 1400/1500 (air-cooled)
QSI 1175/1250 & 1400/1500 (water-cooled)
QSI 245
¯STANDARD°
Full Load Operating Pressure psig 100 110 125 150
Maximum Operating Pressure psig 115 125 140 165
Minimum Operating Pressure psig Æ Æ 75 Å Å
Maximum Ambient Operating Temperature:
Less Cabinet °F Æ Æ 120 Å Å
With Cabinet °F Æ Æ 115 Å Å
Minimum Ambient Operating Temperature °F Æ Æ 32 Å Å
Compressor Drive Motor HP Æ 50 60 Å
Rotor Diameter mm Æ Æ 204 Å Å
Male Rotor Speed rpm Æ 1775 1785 Å
Female Rotor Speed rpm Æ 1183 1190 Å
Rotor Tip Speed m/sec. Æ 18.96 19.07 Å
Inlet Capacity acfm 246 245 243 241
Displacement at Operating Speed cfm Æ 264 265.5 Å
Volumetric Efficiency % 93.2 92.8 91.5 90.8
Aftercooling
Heat Rejection: Fluid Cooler BTU/min. 1893 1994 2124 2387
Aftercooler BTU/min. Æ Æ 352 Å Å
Aftercooler Approach (standard conditions) °F Æ Æ 3-5 Å Å
Maximum Allowable Static Backpressure in./H2O Æ Æ 0.125 Å Å
Fan Motor HP Æ Æ 2 Å Å
Fan Motor rpm Æ Æ 1725 Å Å
Fan Flow cfm Æ Æ 5500 Å Å
Water-cooled Cooling
Recommended Inlet Water Pressure psig Æ Æ 40-100 Å Å
Vent Fan Motor HP Æ Æ 1/9 Å Å
Aftercooler Approach to Cooling:
Water Temperature °F Æ Æ 13-18 Å Å
Water Flow less Aftercooler at: 50°F gpm Æ 3.5 4 Å
70°F gpm Æ 5.3 6.7 Å
90°F gpm Æ 12.5 22 Å
Water Flow with Aftercooler at: 50°F gpm Æ 4.5 5.3 Å
70°F gpm Æ 6.8 8.6 Å
90°F gpm Æ 16 28 Å
Compressor Fluid
Total Fluid Capacity gallons Æ Æ 11 Å Å
Reservoir Fluid Capacity gallons Æ Æ 7.4 Å Å
Fluid Flow gpm Æ Æ 19 Å Å
Typical Fluid Carryover ppm Æ Æ 1.5-5 Å Å
Normal Airend Discharge Temperature °F Æ Æ 175-195 Å Å
Sound (at 1 meter)
Unenclosed (AC/WC) dB(A) Æ Æ 82/80 Å Å
Standard Cabinet (AC/WC) dB(A) Æ Æ 76/73 Å Å
Low Sound Cabinet (AC) dB(A) Æ Æ 71 Å Å
QSI 300
¯STANDARD°
Rotor Tip Speed M/sec. Æ 19.07 19.12 Å
Displacement at Operating Speed cfm *data not available*
Volumetric Efficiency % *data not available*
Aftercooling
Aftercooler BTU/min. 449 450 453 454
Aftercooler Approach (standard conditions) °F Æ Æ 6 Å Å
Water Flow less Aftercooler at: 50°F gpm *data not available*
70°F gpm 5 6.5 7.5 8.5
90°F gpm 10 10.5 11.5 13
Water Flow with Aftercooler at: 50°F gpm *data not available*
70°F gpm 6.5 7.5 8.5 10
90°F gpm 10 11 12 14
Compressor Fluid
Reservoir Fluid Capacity gallons Æ Æ 6 Å Å
Typical Fluid Carryover ppm Æ Æ 1-3 Å Å
Sound (at 1 meter)
Standard Cabinet (AC /WC) dB(A) Æ Æ 76/75 Å Å
Low Sound Cabinet (AC) dB(A) *data not available*
QSI 370
¯STANDARD°
Displacement at Operating Speed cfm Æ 403.1 404.2 Å
Volumetric Efficiency % 92.3 91.5 91 90.1
Aftercooling
Water Flow less Aftercooler at: 50°F gpm Æ 4.7 5.5 Å
70°F gpm Æ 7.1 8.9 Å
90°F gpm Æ 15.2 24.6 Å
70°F gpm Æ 9.2 11.5 Å
90°F gpm Æ 19.4 29.5 Å
Compressor Fluid
Fluid Flow gpm Æ Æ 24.5 Å Å
Sound (at 1 meter)
QSI 500
¯STANDARD°
Displacement at Operating Speed cfm 556.4 556.4 554.8 554.8
Aftercooling
70°F gpm Æ 7.7 8.9 Å
90°F gpm Æ 14.1 24.6 Å
70°F gpm Æ 10.1 11.5 Å
90°F gpm Æ 17.9 29.5 Å
Compressor Fluid
Total Fluid Capacity gallons Æ Æ 23.5 Å Å
Sound (at 1 meter)
QSI 600
¯STANDARD°
Displacement at Operating Speed cfm *data not available*
Volumetric Efficiency % *data not available*
Aftercooling
Aftercooler BTU/min. 1016 1018 1017 1025
Aftercooler Approach (standard conditions) °F Æ Æ 6 Å Å
Water Flow less Aftercooler at: 50°F gpm *data not available*
70°F gpm 15 16 17 38
90°F gpm 25 27 55 38
Water Flow with Aftercooler at: 50°F gpm *data not available*
70°F gpm 12 14 16 27
90°F gpm 21 24 45 29
Compressor Fluid
Typical Fluid Carryover ppm Æ Æ 1-3 Å Å
Sound (at 1 meter)
Low Sound Cabinet (AC) dB(A) *data not available*
QSI 750
¯STANDARD°
Displacement at Operating Speed cfm Æ 831.3 828.9 Å
Aftercooling
70°F gpm Æ 10.1 12.6 Å
90°F gpm Æ 16.1 22.3 Å
70°F gpm Æ 13.1 18.3 Å
90°F gpm Æ 20.4 28 Å
Compressor Fluid
Sound (at 1 meter)
QSI 1000
¯STANDARD°
Full Load Operating Pressure psig 100 110 125
Maximum Operating Pressure psig 115 125 140
Minimum Operating Pressure psig Æ 75 Å
Less Cabinet °F Æ 115 Å
With Cabinet °F Æ 110 Å
Minimum Ambient Operating Temperature °F Æ 32 Å
Compressor Drive Motor HP Æ 200 250
Rotor Diameter mm Æ 321 Å
Male Rotor Speed rpm Æ 1785 1790
Female Rotor Speed rpm Æ 1190 1193
Rotor Tip Speed m/sec. Æ 30.03 30.11
Inlet Capacity acfm 1014 1010 1003
Displacement at Operating Speed cfm Æ 1120 1123
Volumetric Efficiency % 90.5 90.2 89.3
Aftercooling
Heat Rejection: Fluid Cooler BTU/min. 7609 7730 8310
Aftercooler BTU/min. 1530 1610 1731
Aftercooler Approach (standard conditions) °F Æ 3-5 Å
Maximum Allowable Static Backpressure in./H2O Æ 0.125 Å
Fan Motor HP Æ 5 Å
Fan Motor rpm Æ 1180 Å
Fan Flow cfm Æ 19300 Å
Recommended Inlet Water Pressure psig Æ 40-100 Å
Vent Fan Motor HP Æ 1/2 Å
Water Temperature °F Æ 13-18 Å
Water Flow less Aftercooler at: 50°F gpm Æ 10.6 13.2
70°F gpm Æ 14.8 19.6
90°F gpm Æ 25.6 42
Water Flow with Aftercooler at: 50°F gpm Æ 14.1 17.4
70°F gpm Æ 19.1 25.5
90°F gpm Æ 32.4 53
Compressor Fluid
Total Fluid Capacity gallons Æ 46 Å
Reservoir Fluid Capacity gallons Æ 37.25 Å
Fluid Flow gpm Æ 59.5 Å
Typical Fluid Carryover ppm Æ 1.5-5 Å
Normal Airend Discharge Temperature °F Æ 175-195 Å
Sound (at 1 meter)
Unenclosed (AC/WC) dB(A) Æ 89/86 Å
Standard Cabinet (AC/WC) dB(A) Æ 85/79 Å
Low Sound Cabinet (AC) dB(A) Æ 82 Å
QSI 1250
¯STANDARD°
Displacement at Operating Speed cfm Æ 1389 1385
Volumetric Efficiency % 91.3 91 90.6
Aftercooling
70°F gpm Æ 19.9 26.4
90°F gpm Æ 36.7 62.5
Water Flow with Aftercooler at: 50°F gpm Æ 18.5 22.9
70°F gpm Æ 25 33.8
90°F gpm Æ 47 80
Compressor Fluid
Fluid Flow gpm Æ 59.5 Å
Sound (at 1 meter)
QSI 1500
¯STANDARD°
Displacement at Operating Speed cfm Æ 1672.4 1677
Volumetric Efficiency % 90.9 90.6 90.6
Aftercooling
70°F gpm Æ 22.2 29.5
90°F gpm Æ 39 64
Water Flow with Aftercooler at: 50°F gpm Æ 21.2 26
70°F gpm Æ 29 38.2
90°F gpm Æ 49.7 81
Compressor Fluid
Fluid Flow gpm Æ 84 Å
Sound (at 1 meter)
Introduction LOGO Program Block Functions
The PLC LOGO controller is the standard QSI controller. Block number B02 is a latching relay used to latch the
start signal in and supply a continuous start signal to the
program.
To disengage the start signal, remove power to the logo

controller by pressing the stop button or by removing
power to the compressor using a disconnect.
Block number B03 is an off-delay timer which will time

out and shutdown the machine during non usage periods.
The default setting is 10 minutes. This timer may be

adjusted from 0 minutes to 99 hours. Contact the Quincy
service department to change the setting on this timer.
The LOGO controller is a universal logic module which When the pressure switch opens (no signal from input I2),
integrates control functions, an operating and display unit, the off time will begin. If the pressure switch does not
a power supply, an interface for program modules and a close again before the time setting is reached, the
PC cable and basic functions required in day-to-day compressor will shutdown. The compressor will restart
operation, such as functions for on/off delays. when the pressure switch closes or can be restarted by
turning the selector switch to the continuous run position
as long as there are no fault conditions present.
PLC Program Installation Procedure
Block number B05 is a latching relay used to supply
voltage to the H.A.T. annunciator panel light.
After verifying that the connections the LOGO controller
are correct (reference the appropriate wiring diagram in
When the H.A.T. probe circuit opens (no signal from
series WP1962), install the PLC program module chip as
input I3), the Q3 output will energize and send power to
follows :
the annunciator indicator light. The light will stay
• Make sure that all power to the electrical enclosure is energized until power to the LOGO controller is removed.
turned off and perform the appropriate lockout/tagout
procedures. Remove power to the LOGO controller by pressing the
stop button or by removing power to the compressor
• Using a small flathead screwdriver, carefully remove
using a disconnect.
the blank program chip module, located in the upper
right hand corner of the controller face (just above
Block number B06 is a latching relay which prevents the
the up/down arrow keys), from the PLC controller.
unit from starting when a fault condition is present.
• Carefully insert the red chip module, Quincy part
number 143819, into the chip slot. It latches in when there is a fault condition present such as
a motor overload trip, high air temperature, M1 contactor
opening or if the fan contact does not close within the
specified amount of time (refer to block number B09 for
CAUTION! fan timer function).
There is only one way to insert the chip. Do not
Resetting the fault condition will not reset the program.
try to force the program chip into the slot. Doing
To reset the program once the fault is corrected, remove
so will damage the chip and render it useless.
power to the LOGO controller by pressing the stop button
or by removing power to the compressor using a
• Reapply power and the PLC controller will run off of disconnect.
the red program chip module.
Addendum to QSI instruction manual 65005-CB. Created 03/16/04

Setting the Day, Time & Date
Block number B09 is an on-delay timer used to ensure To set the day of the week, time of day and
that the fan contactor engages. current date in the controller, press the ESC
and OK buttons at the same time to display
This block has a fixed 3-second time setting and cannot the parameterization menu.
be adjusted.
Timing will begin upon input to the trigger (Q1). If the

fan contactor normally open auxiliary contact does not
close within 3-seconds (input from I4 to the reset on the
timer), the unit will shutdown and will not restart until Use the or arrow on the control panel to select
power has been removed from the LOGO controller. ‘Set Clock’, then press OK to display the clock settings.
Block number B11 is an on-delay timer used to energize

the wye-delta shorting contactor coil for initial starting
purposes only. The trigger for this timer is block B17.
The cursor is positioned before the day of the week.
The default setting is 6 seconds and may be adjusted from Scroll through the days of the week using the arrow
0 seconds to 99 seconds. Contact the Quincy service keys. When the display shows the correct day, move the
department to change the setting on this timer. cursor to the time position using the arrow keys.
At the end of the time delay period, the shorting contactor The clock uses military time. Change the hour value
coil will disengage. using the arrow keys, then use the arrow
keys to move the cursor to the minute value. Set the clock
Block number B15 is an on-delay timer used to ensure to the correct time and repeat the procedure to set the
that the shorting contactor coil engages before the main date.
contactor coil engages.
Once all settings are correct, press OK to accept the
B15 has a fixed time setting of 1/2 second and cannot be changes.
adjusted.
To switch between summer and winter time (daylight
Block number B17 is an on-delay timer used as the auto- savings time):
restart timer. The trigger for this timer is input I1.
With the LOGO controller in RUN mode:
The default setting is 0 seconds and this setting can be
adjusted from 0 seconds to 99 hours at any time after the Press OK and at the same time to ‘spring’ forward one
program is loaded on the LOGO controller. hour.
Block number B18 is an up/down counter used to log the Press OK and at the same time to ‘fall’ back one hour.
number of times that the main contactor M1 is engaged. It
will record up to 999,999 starts before resetting itself to 0.
Block number B19 is an up/down counter used to log the

number of times that the unload solenoid valve is
energized. It will record up to 999,999 activations before
resetting itself to 0.
Addendum to QSI instruction manual 65005-CB. Created 03/16/04

Notes
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
Notes
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
___________________________________________________________________
QUINCY COMPRESSOR AND ORTMAN FLUID POWER DIVISIONS
STANDARD TERMS AND CONDITIONS
LEGAL EFFECT: Except as expressly otherwise agreed to in writing by an authorized representative of Seller,
the following terms and conditions shall apply to and form a part of this order and any additional and/or different
terms of Buyer’s purchase order or other form of acceptance are rejected in advance and shall not become a part
of this order.
The rights of Buyer hereunder shall be neither assignable nor transferable except with the written consent of
Seller.
This order may not be canceled or altered except with the written consent of Seller and upon terms which will
indemnify Seller against all loss occasioned thereby. All additional costs incurred by Seller due to changes in
design or specifications, modification of this order or revision of product must be paid for by Buyer.
In addition to the rights and remedies conferred upon Seller by this order, Seller shall have all rights and remedies
conferred at law and in equity and shall not be required to proceed with the performance of this order if Buyer is in
default in the performance of such order or of any other contract or order with seller.
TERMS OF PAYMENT: Unless otherwise specified in the order acknowledgment, the terms of payment shall be
net cash within thirty (30) days after shipment. These terms shall apply to partial as well as complete shipments.
If any proceeding be initiated by or against Buyer under any bankruptcy or insolvency law, or in the judgment of
Seller the financial condition of Buyer, at the time the equipment is ready for shipment, does not justify the terms
of payment specified, Seller reserves the right to require full payment in cash prior to making shipment. If such
payment is not received within fifteen (15) days after notification of readiness for shipment, Seller may cancel the
order as to any unshipped item and require payment of its reasonable cancellation charges.
If Buyer delays shipment, payments based on date of shipment shall become due as of the date when ready for
shipment. If Buyer delays completion of manufacture, Seller may elect to require payment according to
percentage of completion. Equipment held for Buyer shall be at Buyer’s risk and storage charges may be applied
at the discretion of Seller.
Accounts past due shall bare interest at the highest rate lawful to contract for but if there is no limit set by law,
such interest shall be eighteen percent (18%). Buyer shall pay all cost and expenses, including reasonable
attorney’s fees, incurred in collecting the same, and no claim, except claims within Seller’s warranty of material or
workmanship, as stated below, will be recognized unless delivered in writing to Seller within thirty (30) days after
date of shipment.
TAXES: All prices exclude present and future sales, use, occupation, license, excise, and other taxes in respect of
manufacture, sales or delivery, all of which shall be paid by Buyer unless included in the purchase price at the
proper rate or a proper exemption certificate is furnished.
ACCEPTANCE: All offers to purchase, quotations and contracts of sales are subject to final acceptance by an
authorized representative at Seller’s plant.
DELIVERY: Except as otherwise specified in this quotation, delivery will be F. O. B. point of shipment. In the
absence of exact shipping instruction, Seller will use its discretion regarding best means of insured shipment. No
liability will be accepted by Seller for so doing. All transportation charges are at Buyer’s expense. Time of
delivery is an estimate only and is based upon the receipt of all information and necessary approvals. The
shipping schedule shall not be construed to limit seller in making commitments for materials or in fabricating
articles under this order in accordance with Seller’s normal and reasonable production schedules.
Seller shall in no event be liable for delays caused by fires, acts of God, strikes, labor difficulties, acts of
governmental or military authorities, delays in transportation or procuring materials, or causes of any kind beyond
Seller’s control. No provision for liquidated damages for any cause shall apply under this order. Buyer shall
accept delivery within thirty (30) days after receipt of notification of readiness for shipment. Claims for shortages
will be deemed to have been waived if not made in writing within ten (10) days after the receipt of the material in
respect of which any such shortage is claimed. Seller is not responsible for loss or damage in transit after having
June 30, 2003 Page 1 of 2

received “In Good Order” receipt from the carrier. All claims for loss or damage in transit should be made to the
carrier.
TITLE & LIEN RIGHTS: The equipment shall remain personal property, regardless of how affixed to any realty or
structure. Until the price (including any notes given therefore) of the equipment has been fully paid in cash, Seller
shall, in the event of Buyer’s default, have the right to repossess such equipment.
PATENT INFRINGMENT: If properly notified and given an opportunity to do so with friendly assistance, Seller will
defend Buyer and the ultimate user of the equipment from any actual or alleged infringement of any published
United States patent by the equipment or any part thereof furnished pursuant hereto (other than parts of special
design, construction, or manufacture specified by and originating with Buyer), and will pay all damages and costs
awarded by competent court in any suit thus defended or of which it may have had notice and opportunity to
defend as aforesaid.
STANDARD WARRANTY: Seller warrants that products of its own manufacture will be free from defects in
workmanship and materials under normal use and service for the period specified in the product instruction
manual. Warranty for service parts will be ninety (90) days from date of factory shipment. Electric Motors,
gasoline and diesel engines, electrical apparatus and all other accessories, components and parts not
manufactured by Seller are warranted only to the extent of the original manufacturer’s warranty.
Notice of the alleged defect must be given to the Seller, in writing with all identifying details including serial
number, type of equipment and date of purchase within thirty (30) days of the discovery of the same during the
warranty period.
Seller’s sole obligation on this warranty shall be, at its option, to repair or replace or refund the purchase price of
any product or part thereof which proves to be defective. If requested by Seller, such product or part thereof must
be promptly returned to seller, freight prepaid, for inspection.
Seller warrants repaired or replaced parts of its own manufacture against defects in materials and workmanship
under normal use and service for ninety (90) days or for the remainder of the warranty on the product being
repaired.
This warranty shall not apply and Seller shall not be responsible or liable for:
(a) Consequential, collateral or special losses or damages;
(b) Equipment conditions caused by fair wear and tear, abnormal conditions of use, accident, neglect or
misuse of equipment, improper storage or damage resulting during shipping;
(c) Deviation from operating instructions, specifications or other special terms of sale;
(d) Labor charges, loss or damage resulting from improper operation, maintenance or repairs made by
person(s) other than Seller or Seller’s authorized service station.
In no event shall Seller be liable for any claims whether arising from breach of contract or warranty or claims of
negligence or negligent manufacture in excess of the purchase price.
THIS WARRANTY IS THE SOLE WARRANTY OF SELLERS AND ANY OTHER WARRANTIES, WHETHER
EXPRESS OR IMPLIED IN LAW OR IMPLIED IN FACT, INCLUDING ANY WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR PARTICULAR USE ARE HEREBY SPECIFICALLY EXCLUDED.
LIABILITY LIMITATIONS: Under no circumstances shall the Seller have any liability for liquidated damages or for
collateral, consequential or special damages or for loss of profits, or for actual losses or for loss of production or
progress of construction, whether resulting from delays in delivery or performance, breach of warranty, negligent
manufacture or otherwise.
ENVIROMENTAL AND OSHA REQUIREMENTS: At the time of shipment of the equipment from the factory,
Quincy Compressor / Ortman Fluid Power will comply with the various Federal, State and local laws and
regulations concerning occupational health and safety and pollution. However, in the installation and operation of
the equipment and other matters over which the seller has no control, the Seller assumes no responsibility for
compliance with those laws and regulations, whether by the way of indemnity, warranty or otherwise.
June 30, 2003 Page 2 of 2

Quincy Service is always near.
There are authorized Quincy
Distributors located worldwide that
stock genuine Quincy parts &
accessories for a wide range of
Quincy products.
Quincy Service specialists are

factory trained and will help keep
you in business. Call for Authorized
Quincy Service.
Quincy
®
Compressor
SM
Tr u e B l u e R e l i a b i l i t y
Rotary/Vacuum/Systems: 251.937.5900
Reciprocating/Systems: 217.222.7700
Nearest Distributor: 888.424.7729
E-mail: [email protected] © 2003 Quincy Compressor, an EnPro Industries company
Discover: www.quincycompressor.com All Rights Reserved. Litho in U.S.A.

Quincy QSI Series: Instruction Manual

Uploaded by

Copyright:

Available Formats

Quincy QSI Series: Instruction Manual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Quincy QSI Series: Instruction Manual

Uploaded by

Copyright:

Available Formats

Quincy

This manual contains important safety

Manual No. 65005-CB April 2001 Edition

Section VI - Servicing (continued)

• Safety Alert Symbols

Safety Alert Symbols

Safety Precautions • Do not change the pressure setting of the pressure

NOTICE! Serial/Model Identification Plate

General Description The Compression Cycle

FEMALE ROTOR DISCHARGE PORT

A) INTAKE B) COMPRESSION C) DISCHARGE

Figure 2-1. Compression Cycle

Air Flow Water-cooled Fluid Coolers

Capacity Control System Auto/Dual (Standard)

Auto/Demand (Optional) Load/No Load (Optional)

A diagram of the electrical system is shown in the parts

Main Power on Light Hourmeter

Air Intake Filter Service Light

This indicator signals when the filter element needs to be

Receiving Moving the Unit to the Installation Site

Check the reservoir and pressure relief valves to be sure

Locate the compressor on a level surface in a clean, well-

Relief Valves Electrical

Quincy would like to emphasize the importance of

Pneumatic Circuit Breakers or Velocity Fuses

The Occupational Safety and Health Act, Section

Removal or painting over safety labels will result

CAUTION! • Check the fan rotation (air flows through the

Stopping the Compressor - Normal Operation Stopping the Compressor - Emergency

The following procedure should be followed for

1) Disconnect and lockout the main power switch and

4) Shut off water and depressurize system if water-

Safety Water Removal

NOTICE! Water vapor may condense in the reservoir and must be

4) Touch the top cap of the separator element with the

6) Touch the outside wire mesh. The indicator light

3) Contact the grounding staple on the separator

Fluid Scavenging System Air Filter

• Once per year. NOTICE!

Control Line Air Filter

An automatic draining control line filter is used.

• Remove the drive coupling hub and key from the

• Apply a thin coat of Loctite™ 290 to the outer steel

• Preheat the wear sleeve (in a small oven) to 350°F.

• Slide the proper seal installation sleeve against the WARNING!

ASSEMBLING THE FACE SEAL END

1) CHECK SEALING SURFACES 3) POSITION TO FITTING

ENSURE THAT O-RING IS PROPERLY

CHECK SEALING SURFACE POSITION AND HOLD FLAT SEALING

2) INSTALL O-RING 4) THREAD ON NUT BY HAND &

IF PROPERLY ALIGNED, THE NUT

CORRECTLY SIZED O-RING

ASSEMBLING ADJUSTABLE END TO PORT

1) CHECK SEALING SURFACES & INSTALL O-RING

• INSPECT FITTING FOR DAMAGE

ASSEMBLING NON-ADJUSTABLE PORT END

• INSPECT SEALING SURFACES FOR DAMAGE

SEAL-LOK ASSEMBLY TORQUES (IN LBS)

• to seal the rotor clearances