Chapter 3 Exam Quiz Instruc Ons: Started: Feb 25 at 2:41pm
Chapter 3 Exam Quiz Instruc Ons: Started: Feb 25 at 2:41pm
Chapter 3 Exam
Started: Feb 25 at 2:41pm
Question 1 1 pts
Refer to the exhibit. What destination address will RTB use to advertise LSAs?
224.0.0.5
224.0.0.6
10.1.7.17
172.16.1.1
172.16.2.1
255.255.255.255
Question 2 1 pts
What does the Cisco IOS use to calculate the OSPF cost to a destination network?
bandwidth
https://1314297.netacad.com/courses/792192/quizzes/7142650/take 1/9
25/2/2019 Quiz: Chapter 3 Exam
Question 3 1 pts
Which two statements are true about multiarea OSPF? (Choose two.)
A stub area does not accept information from other OSPF areas.
A stub area does not accept information from outside the OSPF autonomous system.
ABRs maintain a separate link-state database for each area to which they are attached.
Internal routers maintain a separate link-state database for each area to which they are
attached.
Question 4 1 pts
What are two reasons for creating an OSPF network with multiple areas? (Choose two.)
to provide areas in the network for routers that are not running OSPF
to simplify configuration
Question 5 1 pts
For OSPF, which three options must be the same within the hello packet that is
exchanged between two adjacent routers? (Choose three.)
area ID
DR/BDR assignments
https://1314297.netacad.com/courses/792192/quizzes/7142650/take 2/9
25/2/2019 Quiz: Chapter 3 Exam
hello/dead intervals
router priority
stub flag
Question 6 1 pts
Refer to the diagram. Which state is RTB in if it sees itself in the RTA hello but no routing
information has been exchanged?
attempt state
down state
init state
loading state
two-way state
Question 7 1 pts
Refer to the exhibit. When OSPF is operational and converged, what neighbor
relationship is developed between Router1 and Router2?
https://1314297.netacad.com/courses/792192/quizzes/7142650/take 3/9
25/2/2019 Quiz: Chapter 3 Exam
Router2 will become the DR and Router1 will become the BDR.
Question 8 1 pts
Refer to the exhibit. What does the state "FULL/ -" indicate?
The router with router ID 10.112.0.34 and RouterA are on a point-to-point network.
RouterA could not form a neighbor relationship with the router with router ID 10.112.0.34.
OSPF hello and dead timers between RouterA and the router with router ID 10.112.0.34 do not
match.
Question 9 1 pts
https://1314297.netacad.com/courses/792192/quizzes/7142650/take 4/9
25/2/2019 Quiz: Chapter 3 Exam
Question 10 1 pts
100
255
Question 11 1 pts
What does OSPF use to reduce the number of exchanges of routing information in
networks where large numbers of neighbors are present? (Choose two.)
root router
domain router
designated router
Question 12 1 pts
In an OSPF hub-and-spoke topology, what needs to be done to ensure that the spoke
routers would never be selected as DR and BDR?
https://1314297.netacad.com/courses/792192/quizzes/7142650/take 5/9
25/2/2019 Quiz: Chapter 3 Exam
All routers must be configured with an OSPF interface priority of 0 (ip ospf priority) to disable
the DR/BDR election process.
All spoke routers need to be configured with an OSPF interface priority of 0 (ip ospf priority) so
that they will not become the DR/BDR.
One of the spoke routers will need to be configured as the DR by setting the OSPF interface
priority higher than 1 (ip ospf priority).
Question 13 1 pts
Which two statements are correct about OSPF route summarization? (Choose two.)
The metric of the summary route is equal to the lowest cost network within the summary address
range.
The area 51 range 172.0.0.0 255.0.0.0 command identifies area 51 as the area that contains the
range of networks to be summarized.
OSPF can perform automatic summarization on major classful network boundaries even if no
summarization commands are entered from the CLI.
Once OSPF route summarization is configured, the summary route will be advertised even if
none of the networks in the address range are in the routing table.
Question 14 1 pts
Which two statements are true about inter-area and intra-area routes in multi-area
OSPF? Choose two.
An internal router will add the cost to reach a specific ABR to the cost announced in a type 3
LSA
For an intra-area route, an internal router will only consider the cost to reach a specific ABR
https://1314297.netacad.com/courses/792192/quizzes/7142650/take 6/9
25/2/2019 Quiz: Chapter 3 Exam
Question 15 1 pts
In which two types of areas will the ABR forward LSA 3s into an area? Choose two.
Normal area
Stub area
Question 16 1 pts
Which of the following statements are true regarding OSPFv3? Choose two.
Uses a 32-bit router ID for configuring OSPFv3 for IPv4 and a 128-bit router ID for OSPFv3 for
IPv6
Uses a 32-bit router ID for configuring OSPFv3 for IPv4 and IPv6
Uses IPv4 to transport OSPFv3 messages for IPv4 and IPv6 to transport OSPFv3 messages for
IPv6
Uses IPv6 to transport OSPFv3 messages for IPv4 and OSPFv3 messages for IPv6
Question 17 1 pts
Which global configuration command is used to enter OSPFv3 using address families?
Router(config)# ospfv3 1
https://1314297.netacad.com/courses/792192/quizzes/7142650/take 7/9
25/2/2019 Quiz: Chapter 3 Exam
Question 18 1 pts
Which two statements are true when using OSPFv3 to connect to a router that is only
advertising OSPFv3 routes for IPv4 networks?
IPv6 addressing is not required on the router that is only advertising OSPFv3 routes for IPv4
networks
Question 19 1 pts
Which type of LSA is generated by the ABR to identify and provide a route to the ASBR?
Type 1 LSA
Type 2 LSA
Type 3 LSA
Type 4 LSA
Type 5 LSA
Question 20 1 pts
Which type of LSA is generated by the ASBR when configured with a default static route
and the OSPF default-information originate command?
Type 1 LSA
Type 2 LSA
Type 3 LSA
Type 4 LSA
https://1314297.netacad.com/courses/792192/quizzes/7142650/take 8/9
25/2/2019 Quiz: Chapter 3 Exam
Type 5 LSA
https://1314297.netacad.com/courses/792192/quizzes/7142650/take 9/9