Instruments: Washing Disinfection Catalogue

INSTRUMENTS
washing
disinfection
catalogue
washing and disinfection

machines
laboratory sector
INSTRUMENTS
Philosophy page 2
Smeg Instruments page 4
Why choose a Smeg glassware washer? page 6
Washing volumes page 8
Technical features: symbols page 12
Basic line: GW2045, GW1060, GW4060 page 14
Professional line: GW3060, GW4090 page 20
Glassware washer optional page 24
GW2045 Configuration page 26
GW1060,4060,3060,4090 Configuration page 28
GW2045,1060,4060,3060,4090
Washing Accessories page 30
Professional line: GW6090 technical data sheet page 40
GW6090 optionals page 42
GW6090 configurations page 44
GW6090 accessories page 50
Water treatment page 52
Detergents and additives page 54
External dimensions page 56
Machines technical features page 60
1
INSTRUMENTS
Founded in Guastalla in
1948, the Smeg Group with almost 2000
employees and 15 branches around the world
today represents a point of excellence for Made
in Italy. Smeg has made a name for itself with its
unique profile in the panorama of domestic and
professional appliance manufacturers thanks to
a deep-rooted corporate culture paying the utmost
attention to the quality, technological content
and design of its products.
Smeg Instruments has for more than 25 years
stood by these values also in the design and
manufacture of laboratory glassware washers
enriching them with know-how gained through
collaboration with professional operators in more
than thirty countries around the world.
With an integrated structure from design
to after-sales service Smeg Instruments offers
the laboratory world state-of-the-art washing
and disinfection products, customised solutions,
and flexible and efficient services.
3
MADE
IN ITALY
SERVICE INNOVATION QUALITY RELIABILITY

Smeg also takes care of its A team of expert designers, Manufacturers of professional All the Smeg products are
customers throughout the supported by the most devices cannot improvise. made using top quality
lifetime of the product with modern equipment and Achieving impeccable materials and the best
its numerous specialised in collaboration with washing and components available on the
technical service centres sector experts, design disinfection results is an market today.
spread across the entire high-quality products absolute must for both Smeg particularly stands out
national and world market. in conformity with the Smeg and its customers. for its careful selection of
Installation, testing and most recent directives and With tens of thousands of the steels employed and its
personnel training are done regulations. In the design of machines installed in Italy masterly work. Smeg
directly by Smeg. the entire new range of Smeg and across the world, Smeg moreover implements an
A toll-free number can be glassware washers we set can boast consolidated and articulated quality system
called for round-the-clock ourselves the objective extensive experience in the testing 100% of its production
qualified assistance for every to be in the vanguard field of laboratory glassware at the end of the line followed
need. Putting your trust in and set new standards in the and material washing, which by statistical quality control
Smeg means finding an sector. has allowed us to design by simulating 10-year
after-sales service working a range of professional machine use. Smeg has been
from a warehouse products to the highest a reliable partner of the main
of 5,000 m2 and able quality standards. Smeg has national and international
to deliver spare parts in obtained ISO 9001:2000 distributors of laboratory
24 hours by means of and ISO 13485:2004 quality materials for over twenty
simple and complete Web certification. years.
management (Smeg Tech).
OVER 25 YEARS SERVICE, TECHNOLOGY AND SAFETY
MISSION VISION
Our customers are Those who work in this unfailing customer care, and
professionals who live sector always require top personal dedication and
and work in extremely performance. commitment.
complex organisations Every day they are aware of This is what we demand
and require professional the value of their commitment of ourselves and of our
solutions that guarantee and expertise, give and collaborators, this is what
impeccable performance, demand the best. we offer our customers.
perfect efficiency and the They know that their
highest possible reliability. working tools are an integral
Our mission is to offer these part of their professional
solutions and win their trust. performance and that their
success and personal
satisfaction also depend on
them. We give these persons
peace of mind offering
them faultless performance:
impeccable results and
utmost reliability.
We are well aware that
achieving these results
and maintaining the
level of excellence is not
easy. It requires continual
investments in research
and technology, product
inventiveness and creativity,
5
WHY CHOOSE A SMEG GLASSWARE WASHER?
VAST RANGE AUTOMATIC WASTEWATER

OF WASHING WASHING SEPARATION
ACCESSORIES
Smeg offers a vast range The automatic washing pro- The Smeg models can be
of specific trolleys and cess of the Smeg equipped with a wastewater
accessories for washing glassware washers guaran- separation system.
glassware in chemical, tees extremely high per- This allows separating
pharmaceutical and formance quality ensuring the washing wastewater
petrochemical laboratories excellent controllable results, full of potentially polluting
They are made of AISI 316L verifiable and repeatable over substances from the rinsing
or 304 steel and of chemical time. water containing a negligible
refractory and heat-resistant Automatic washing concentration of pollutants
materials. The combination allows achieving impeccable and can therefore be drained
and choice of the various results and the margin of into the normal sewerage.
accessories depend on the error is reduced to a
type and quantity of glassware minimum.
to be washed. Particular The efficiency and
attention has been paid to thoroughness of automatic
shapes and sizes in order to washing guarantee an
ensure that the accessories impeccable result and
are easily interchangeable. The effective disinfection even
water intakes are automatically for the most complex and
coupled to the internal drying delicate materials. The risks
air ducts when the door is of damaging the material
closed. are eliminated resulting in a
All the accessories are longer life and guaranteeing
dimensionally compatible with perfect drying.
the various models.
WHY CHOOSE A SMEG GLASSWARE WASHER?
DISINFECTION CONTROLLED PROGRAMMABLE

DETERGENT WASHING CYCLES
DISPENSING SYSTEM
The Smeg disinfection Washing effectiveness is The heart of the new-

machines guarantee first and foremost based generation Smeg disinfection
impeccable washing and on proper execution of the machines is the ultra
effective disinfection of detergent and neutralising modern control system
also complex and delicate phases of the material with microprocessors that
instruments. The GW2045, treated. control every activity carried
GW1060, GW4060, GW3060 The models GW2045, out and monitor (by means
and GW4090 models are GW1060 e GW4060 are of redundant system) the
equipped with automatically equipped with a dispenser entire flow of information
regenerated washing water for alkaline powder and a processed by the machine.
softeners and use freshly peristaltic pump for the acid The entire GW series offers
drawn water in every phase. neutraliser. the possibility of programming
While the GW3060 and all the washing parameters
GW4090 models have two by means of a multifunction
peristaltic pumps, respectively membrane keyboard or
dedicated to feeding alkaline directly from the PC thanks
detergent in the washing to the RS232 and the WD-
phase and acid-based TRACE ® registered software.
neutraliser in the neutralisation All the most significant
phase. Each pump is parameters can be set, for
equipped with a level sensor example: execution times,
to be positioned directly in operating temperature,
the can of the products used. additive quantity, number of
The machines are designed phases. Access to the control
to dispense up to 4 different operations is protected
additives. Liquid alkaline by a system of four user
detergents, new enzyme- passwords.
based detergents or acid-
based neutralisers,
caustic soda, disinfectants
and/or defoaming additives
can be used.
7
wide choice in washing volumes - BASIC LINE
The range of professional Smeg washing machine, Basic line, is projected and manufactured specifically with qua-
lity materials as stainless steel AISI 316L. At the same time, those models maintains as specific distinctive features,
the reduced dimensions and the simplicity of their utilization. Since years, Smeg keeps to improve its products for
guaranteeing to its clients any answers for an efficient washing and disinfection. At the same time, those models
can meet space and quality requirements.
GW2045 GW1060
GW2045 is a glassware washer with reduced GW1060 is designed to operate with 1 or 2 levels
dimensions projected to work at 1 or 2 washing levels for treating various types of substances. Washing
and to treat substances of different nature. Washing chamber 520x515x545 mm. Possibility of washing and
chamber 380x480x580 mm. Possibility of washing and disinfecting.
disinfecting.
wide choice in washing volumes - BASIC LINE
Smeg spa has developed a new generation machine, GW4060, even if in a compact space, it presents the more
advanced technologies as drying system with forced air and integrated peristaltic pumps
GW4060
GW4060 is designed to operate with 1 or 2 levels for

treating various types of substances. Washing chamber
520x515x545 mm. Possibility of washing, disinfecting and
drying with “Drying system”.
9
WIDE CHOICE IN WASHING VOLUMES - professional line
The range of professional Smeg washing and disinfection machines is manufactured according to specific projects
using professional materials and special components in order to achieve the best results from a technological
point of view. The wash chambers are made of AISI 316 L quality stainless steel resistant to strong acids (as used
in the pharmaceutical and food industries).
GW3060 GW4090
GW3060 is designed to operate with 1 or 2 GW4090 is designed to operate with 1 or 2

levels for treating various types of substances. levels for treating various types of substances.
Standard washing chamber 520x515x545 mm. Standard washing chamber 520x515x545 mm.
Possibility of washing, disinfecting and drying. Possibility of washing, disinfecting and drying
with Drying System.
WIDE CHOICE IN WASHING VOLUMES - professional line
The plastic materials used are the result of more than 25 years of testing and direct experience in the most varied
application fields. They are heat-resistant and inert and offer excellent resistance to corrosive substances and se-
lected organic solvents. The range of machines meets the glassware decontamination requirements of laboratories
operating in the general chemical, organic and petrochemical fields. For laboratories operating in the biological sec-
tor, Smeg guarantees complete biological decontamination (in accordance with BGVV standards).
GW6090
GW6090 is a machine with a high loading capacity

capable of handling large quantities of material in
a short space of time and of washing large-sized
instruments.
Washing chamber 670x650x835 mm (three times
the useful volume of medium-sized machines).
Able to load up to three direct injection glassware
levels or 3 levels with rotating spray arms.
11
TECHNICAL FEATURES - symbols
The new generation of Smeg glassware washers GW2045, GW1060, GW4060, GW3060, GW4090 and GW6090 may
today be considered the technological benchmark in the glassware washing and disinfection sector.
Every laboratory has its own particular professional washing problems: all of them, be it in general chemistry or bacteriology,
organic chemistry or petrochemistry, food or pharmaceutics, have residues that need to be treated in a different and
appropriate way to achieve the required level of cleaning and disinfection.
PROGRAMMABLE assures “intelligent” management ADDITIONAL

of the drying circuit by automatically PERISTALTIC
The heart of the new adjusting fan speed (thereby reducing PUMPS FOR
generation of Smeg power consumption) according to the
ADDITIVES
disinfectors is the leading- temperature measured in the washing
chamber. The air intake passes through a

edge management system controlled by
The new GW models can have
microprocessors which can control at class C filter with a 98% efficiency rating.
up to two additional peristaltic pumps
all the activities performed and monitor,
dedicated to dispensing additives
using redundant systems, the entire
(caustic soda, defoamers, inhibitors,
flow of information processed by the
disinfectants). Each pump is equipped
equipment. The entire GW series allows
with a level sensor to be positioned
operators to programme all washing
directly in the can of the products used.
parameters as they prefer, using the
multi-function membrane keypad or
the PC directly via the RS232 or LAN
connections and the WD-TRACE PERISTALTIC
software ®. All significant parameters PUMPS: DETERGENT STORE
can be set. These include: execution DETERGENT AND
times, operating temperatures, quantity NEUTRALISER Ergonomics, reduced
of additives, number of phases, and so dimensions and practicality
on. Access to the control operations Disinfection effectiveness mainly depends are indispensable
is protected by a system of four user on the correct performance of the requirements for all equipment used in
passwords. washing phases and the neutralisation busy professional surroundings. With
of the treated material. Models GW3060 these requirements in mind, Smeg has
and GW4090 feature two peristaltic designed a detergent store located
pumps dedicated to dispensing the inside the reduced dimension of the
DRYING SYSTEM glassware washer itself. It can contain up
alkaline detergent during the cleaning
phase and the acid neutraliser during the to four 2-litre containers for the GW4090
The forced-air “Drying
neutralisation phase respectively. Each series and four 5-litre containers for the
System”, completely
pump is equipped with a level sensor to GW6090 series. No product feed pipes
modified in the new GW
be positioned directly in the can of the project from the volume of the glassware
series, is a high-performance rapid
products used. washer.
drying system. The system, comprising
an efficient hot air generator and a About the models GW2045, GW1060
powerful fan, is directly managed by the e GW4060, it is possible to install a
programmer which allows both operating specific optional pump to dispensing the
time and temperature parameters alkaline detergent.
to be modified. The microprocessor
TECHNICAL FEATURES - symbols
LAN CONNECTION CONNECTION STEAM

RS232 CONDENSER
Thanks to the dedicated RS232
Smeg WD-TRACE software A significant feature of the The steam condenser
®
it is possible to visualise new-generation rapidly reduces the
each piece of equipment as though it equipment is that it incorporates the saturated steam from the washing water,
were a terminal, thus being able to store devices required for the complete especially during the thermal disinfection
all the machine data directly on PC. As communication of data relative to phases. This device eliminates the
information communication is two-way, completed processes. The range of last- formation of condensation near the
it is possible to directly dialogue with generation GW features two standard glassware washer and prevents humidity
the disinfector microprocessors, for RS232 outputs, one for connection with and smells from escaping into the air,
example, in order to change the cycle the printer and the other for connection especially in the versions positioned
parameters or display a chart of internal with the PC in order to download all underneath worktops.
temperatures. the information relative to completed In air-conditioned rooms moreover,
washing and disinfection programmes. limiting the dispersion of heat from the
glassware washer reduces the work
load of the air-conditioning system,
considerably decreasing electricity
The parameter A0 consumption and unwanted temperature
changes.
PRINTER
Is a numerical value deriving
from an equation that directly
The traceability of the relates two fundamental
washing and thermal parameters: temperature and thermal
disinfection cycles performed in disinfection time.
professional glassware washers Basically, the value of A0 defines
is required in order to check the the level of lethality of the process
operations have been successfully expressed in seconds. The value
completed. The printer is an accessory appears directly on the display and, if a
which can provide a detailed report printer is installed, it is also
containing all information relative included in the end-of-cycle report.
to cycle performance. In both the
free-standing and panel versions,
the thermal printers used in the GW
series provide complete supporting
documentation for operators.
13
technical data sheet
GW2045
RS232
OPTIONAL OPTIONAL OPTIONAL
GW2045 technical features All versions

Electronic control Microprocessor
Standard programs stored 6
Customisable programs 2
Display with segments and warning light yes
Clock and calendar yes
Reprogrammable phases 8
Phase parameters type of water, detergent quantity, target temperature, extension time in minutes, temperature
Tank internal temperature from room temperature to 95°C
Accuracy 0,1°C
Temperature sensors in tank PT 1000 CLASS B IEC 60751
Display 2 digits
Detergent dosing system max. 1 powder dispenser and 2 liquid pumps
Detergent level sensor optional
Alkaline powder detergent dispenser yes
Pump to dispense acid
neutralized liquid yes
Pump to dispense
alkaline liquid detergent optional
Safety lock yes, with electromagnetic release
Safety devices safety thermostats, door interlock
Alarm display 30
Troubleshooting menu yes, using PC connection
Programme editing yes, using 2 spare programmes
auxiliary functions
Traceability storage of data for 100 most recently run programmes
RS232 serial port for PC connection yes
RS232 serial port for printer yes
Cycle storage yes, WD-TRACE®/Excel format
Cycle file download yes, WD-TRACE® format
water supply
(PREssure 1,5-5 BAR)
Cold water inlet yes, max 42º F hardness
Demineralised water inlet yes, < 20 μS/cm
Demineralised water booster pump optional
Water softener incorporated yes
Recirculation pump 200 l/min
Water heating
Electrical 3,0 kW max
steam condenser optional
dimensions LxDxH mm
Outside (with built-in top) 450x620x850 (830)
Inside 380x480x590
Net weight (Kg) 61
stainless steel
Wash tank AISI 316L
Exterior covering AISI 304
electrical power supply
Max. voltage/power 1/N/PE 230V ~ 50Hz 3,3 kW
noise level max 50 dB
15
GW1060
RS232
OPTIONAL OPTIONAL OPTIONAL OPTIONAL

Display with segments and warning light yes
Phase parameters type of water, detergent quantity, target temperature, extension time
Accuracy 0,1°C
Display 2 digits
Pump to dispense
Safety lock yes, with electromagnetic release and automatic opening
Alarm display 30
Programme editing yes, using 2 spare programmes
auxiliary functions
Traceability storage of data for 100 most recently run programmes
water supply
Cold water inlet yes, max 42º F hardness
Water heating
Electrical 6,3 kW on tri-phase version, 2,3 kW on mono-phase version
dimensions LxDxH mm
Inside 520x515x545
Net weight (Kg) 77
stainless steel
Wash tank AISI 316L
Max. voltage/power 1/N/PE 230V ~ 50Hz 2,8 kW 3/N/PE 400V ~ 50 Hz 7,0 kW
17
GW4060
RS232

Display with segments
yes
and communication led icons
Phase parameters type of water, detergent quantity, target temperature, extension time in minutes, drying temperature and time
Accuracy 0,1°C
Display 4 digits
Pump to dispense
Alarm display 30
Programme editing yes, using 6 spare programs
auxiliary functions
Traceability storage of data for 100 most recently run programs
DRYING SYSTEM
Drying fan yes
Drying heating element 0,8 kW
Prefilter class C 98% yes
HEPA filter Class S 99.999% optional
water supply
Cold water inlet yes
Water heating
Electrical 6,3 kW on tri-phase version, 2,3 kW on mono-phase version
dimensions LxDxH mm
Inside 520x515x545
Net weight (Kg) 77
stainless steel
Wash tank AISI 316L
Max. voltage/power 1/N/PE 230V ~ 50Hz 2,8 kW mono-phase version 3/N/PE 400V - 50 Hz 7,0 kW
19
TECHNICAL DATA SHEET
GW3060
RS232
GW3060 TECHNICAL FEATURES All versions

Electronic control 3 microprocessors +1 (optional communication card)
Customisable programs 10 (expandable to 50)
Backlit graphic LCD display 128 x 64 pixels
Phase parameters type of water, detergent quantity, target temperature, extension time
Tank internal temperature from room temperature to 95º C
Accuracy 0.1°C
Detergent pumps 4 max
Powder detergent dispenser optional
Alarm display 80
Troubleshooting menu yes
Program editing yes (via password)
Password 4 levels
Display languages Italian, English, French, German, Russian and others on request
AUXILIARY FUNCTIONS
External sensor duct optional
Traceability Storage of data for 100 most recently run programs
Waste water separation solenoid optional
valve control
WATER SUPPLY
(PRESSURE 1.5-5 BAR)
Cold/hot water inlet yes, 42 °F hardess
Demineralised water inlet yes, <20μS/cm
WATER HEATING
Electrical 6.3 kW max
Water pre-heating via boiler optional
steam CONDENSER optional
DIMENSIONS LxDxH mm
Inside 520x515x545
Net weight (kg) 76
stainless STEEL
Wash tank AISI 316L
ELECTRICAL POWER SUPPLY
Max. voltage/power 1/N/PE 230V ~ 50Hz 2.8 kW 3/N/PE 400V ~ 50Hz 7.0 kW
NOISE level max 50 dB
21
GW4090
RS232
GW4090 TECHNICAL FEATURES

Phase parameters type of water, detergent quantity, target temperature, extension time in minutes, drying temperature and time
Accuracy 0.1°C
Detergent pumps 4 max
Alarm display 80
Password 4 levels
AUXILIARY FUNCTIONS
Waste water separation
optional
solenoid valve control
DRYING SYSTEM
Drying fan yes
Drying heating element 2 kW
WATER SUPPLY
Cold/hot water inlet yes, max 42°F hardness
WATER HEATING
Water pre-heating via boiler optional
STEAM CONDENSER optional
DIMENSIONS LxDxH mm
Inside 520x515x545
Net weight (kg) 83
stainless STEEL
Wash tank AISI 316L
Max. voltage/power 1/N/PE 230V ~ 50Hz 2.8 kW 3/N/PE 400V ~ 50Hz 7.0 kW
23
GW2045, GW1060, GW4060, GW3060 AND GW4090 OPTIONALS
MACHINE OPTIONALS
pad
Booster pump for non-pressurised demineralised water.
Allows feeding the machine with demineralised water
drawn from a non-pressurised tank positioned at a minimum height of 85
cm from the ground.
pad 2
drawn from a non-pressurised tank positioned on the ground.
ADU
Universal peristaltic pump for liquid additive
• For the dosing of a liquid additive, for ex: alcaline detergent, caustic
soda or antifoam
• With st/steel drawing pipe
• Suitable for tanks of 2l, 5l, 10l
IC5090
On the basis of demineralized water conductivity used during
the last rinse phase, it allows to detect any impurities and to
activate also further rinse phases for achieving a perfect rinse
with low conductivity
WD-VDS
Double discharge valve that allows separating and ducting the polluted
wastewater from the first washing cycles from the final rinsing water.
This wastewater separation device is composed of 1 and 1/2” valves
with Viton membrane and valve opening is controlled by the machine
microprocessor.
WD-LS3060
Detergent level sensor. Allows controlling the level of liquid additives and
signals when the detergent has run out. Equipped with an adjustable
drawing tube for scans of different heights.
GW2045, GW1060, GW4060, GW3060 AND GW4090 OPTIONALS
STAINLESS STEEL BASES AND FRAMES
B9040
Base for 90 cm wide models only.
The frame allows bringing the machine loading level up to an ergonomic
height approximately 70 cm from the ground. Entirely made of stainless steel.
A detergent compartment with anti-drip bottom and front door with push-pull
opening is integrated in the base.
Dimensions l x d x h = 900x530x400 mm
B6040 (not shown in the photo): for 60 cm wide models only.
B9040QWC
Base with integrated demineralised water boiler. For 90 cm wide
models only. A boiler is housed in the base to preheat the demineralised
water to get fastest cycles
Dimensions: l x d x h = 900x530x400 mm
T9040
Frame for 90 cm wide models only.
The frame allows bringing the machine loading level up to
an ergonomic height approximately 70 cm from the ground.
The frame also facilitates cleaning the machine underneath.
Entirely made of stainless steel.
T6040 (not shown in the photo): frame for 60cm models only.
Dimensions l x p x h = 600x530x400 cm
TRACEABILITY OPTIONALS
WD-PRINT
External 24-character impact matrix printer with real-time clock function.
Complete with thermal paper roll.
WD-PAPER Thermal paper roll. Diameter 50 mm, width 57 mm.
25
GW2045 configurations
The machine bodies in the BASIC series must be equipped with carriages and supports most suited to the specific
treatment requirements of the different types of glassware used in the laboratory.
The various possible machine/carriage configurations described below are meant as a guide to help you choose the most
appropriate solution for the type of glassware used.
TWO SPRAYING LEVELS

This configuration has two washing levels with rotary sprays where
supports for all types of glassware can be located (beakers, test tubes,
flasks, plates and various other materials).
Photo:
D-CS1 upper rack: SB9 straight tine support for beakers and flasks to
the left, SB14 spring tine support to the right. Each support occupies ½
the rack for machines with width of 45 cm.
D-CS2 lower rack: SB28 universal spring support for beakers and flasks,
standard on 60-cm models, occupying all of the lower base but cannot
be positioned on the upper rack.
TWO SPRAYING LEVELS

This configuration has two washing levels with rotary sprays where
supports for all types of glassware can be located (beakers, test tubes,
flasks, plates and various other materials).
Photo:
D-CS1 upper rack: the carriage is fitted with 2 racks equipped with
compartments (CP192 and CP222) to wash test tubes.
D-CS2 lower rack: SB9 straight tine support for beakers and flasks to the
left, SB14 spring tine support to the right. Each support occupies ½ the
rack for machines with width of 45 cm to optimise the load on the rack.
ONE INJECTION LEVEL

The LM24 is secured to the lower D-CS2 base using two special
fastenings. This solution is suitable for washing narrow-necked glassware
of different sizes. It has a capacity of 24 items and can wash both large
items and small flasks or bottles. ULB 40 adaptor nozzles for pipettes
can also be fitted. The maximum height of glassware is 500 mm.
Photo:
LM24 support
Note: the configurations shown on these two pages are only available with models of 45 cm.
GW2045 configurations
TWO SPRAYING/INJECTION LEVELS

In this configuration there are two washing levels: lower level with rotary
sprayers to hold various supports (beakers, test tubes, flasks). The
D-CS1 upper base is fitted with the 24-position LM22S injection base.
This configuration allows simultaneous washing of narrow-necked and
other types of glassware.
Photo:
left, SB14 spring tine support to the right. Each support occupies ½ the
rack for machines with width of 45 cm to optimise the load on the rack.
ONE MIXED INJECTION LEVEL

This configuration allows simultaneous washing of narrow-necked
glassware (flasks, and beakers) and 12 pipettes with a maximum height of
510 mm. This is an ideal solution for washing various types of glassware
simultaneously without having to use dedicated separate carriages with a
greater capacity.
Photo:
LPM24 carriage

In this configuration there are two washing levels: the upper level is fitted
with the KP60 seventy-item base for centrifuge vials and test tubes. The
lower level is spare.
Photo:
D-CS1 upper rack: KP60 base.
left, SB14 spring tine support to the right.
TWO INJECTION LEVELS

LM46 carriage consisting of two injection levels for a capacity of 46
items. This version maximises the injection washing capacity. The
maximum height of glassware is 225 mm. Recommended for flasks
(ISO1042) with volume of 5 to 200 ml, bottles (ISO 4796) up to 1000 ml
and flasks up to 1000 ml.
Photo:
LM46 carriage composed by 22-position upper rack and 24-position
lower rack.
27
GW1060, GW4060, GW3060 AND GW4090 CONFIGURATIONS
The machine bodies of the GW1060, GW4060, GW3060 and GW4090 series must be equipped with trolleys and sup-
ports most suited to the specific treatment requirements of the different types of glassware used in the laboratory.
The various possible machine/trolley configurations described below are meant as a guide to help you choose the most
appropriate solution for the type of glassware used.
TWO SPRAYING LEVELS

Standard lower basket CS2 and upper basket with sprayer CS1-1. In this
configuration there are two washing levels with rotary sprayers where
all the supports for the various glass items can be positioned (it can be
used for washing beakers, test tubes, flasks, plates and various other
materials). The upper basket CS1-1 can be positioned on two levels to
make better use of the space.

Standard lower basket CS2 and upper injection basket. In this
configuration there are two washing levels: a lower level with rotary
sprayers to hold various supports (beakers, test tubes, flasks) and an
upper level with a 40-position injection trolley LM40S (LM40SDS for
machines with drying system).
This configuration allows simultaneous washing of narrow-necked and
other types of glassware.
ONE SPRAYING/INJECTION LEVEL

LM20 trolley (LM20DS for machines with drying system) one half with a
multi-spigots injection system and the other half to hold supports. In this
case, narrow-necked glassware up to 500 mm in height can be washed
at the same time as test tubes. Compared to the configuration with two
spraying/injection levels, this one has the advantage that you can wash
glassware more than 245 mm in height.
GW1060, GW4060, GW3060 AND GW4090 CONFIGURATIONS
ONE INJECTION LEVEL

LM40 trolley (LM40DS for machines with drying system).
It may be considered as a universal injection trolley as it optimises wash-
ing of narrow-necked glassware of different sizes. It has a capacity of 40
items and can wash both large items and small flasks or bottles.
TWO INJECTION LEVELS

LM80 trolley (LM80DS for machines with drying system) with
two injection levels for a capacity of 68 items.
This version maximises the injection washing capacity.
ONE MIXED INJECTION LEVEL

LPM20/20 trolley (LPM2020DS for machines with drying system): this
system allows simultaneously washing narrow-necked glassware (flasks,
beakers, round-bottom flasks) and 20 pipettes. It is a valid solution when
needing to wash many different types of glassware at the same time
without having to resort to a specific larger capacity trolley.
29
GW2045, GW1060, GW4060, GW3060 AND GW4090 WASHING ACCESSORIES
Basic trolleys
D-CS1 (only on GW2045 model)

Upper carriage with sprayer.
Made for stainless steel and suitable for positioning racks and supports.
CS1-1 (not in photo)

Upper carriage with sprayer.
D-CS2 (only on GW2045 model)

Lower carriage with sprayer.
CS2 (not in photo)

Basic lower carriage.
Flask and beaker supports
SB9 (only on GW2045 model)

Stainless steel 9-position support for tunnels and breakers with max volume
of 100 ml. Occupies 1/2 of the D-CS1/D-CS2 carriages.
SB14 (only on GW2045 model)

Stainless steel 14-position support for beakers and flasks with volume of
250 to 1000 ml. Occupies 1/2 of the D-CS1/D-CS2 carriages.
SB15
16-position spring support for flasks, beakers, etc. For use in combination
with standard CS1-1/CS2 racks and LM20 carriage.
It has a capacity of 16 items and is made of stainless steel.
Reccomended for flasks with a capacity of up to 1000 ml.
SB28 (not in photo): 28-position spring support for flasks, beakers, etc.
For use in combination with standard CS1-1/CS2 racks and LM20 carriage.
Recommended for flasks with a capacity up to 1000 ml.
SB30
30-position support to hold beakers of any size and to be used with the
standard baskets CS1-1 and CS2 and the trolley LM20. It has a capacity
of 30 items and is made of stainless steel.
Recommended for beakers with a capacity smaller than 500 ml.
SB25 (not shown in the photo): 28-position spring support to hold flasks
and beakers and to be used with the standard baskets CS1-1 and CS2.
Recommended for flasks with a capacity smaller than 500 ml.
PLATE AND SLIDE Supports
PV105
Microscope slide basket made of stainless steel.
Suitable for positioning 105 standard microscope slides.
Dimensions l x d x h = 220x143x60 mm.
SL6
Olympus-type plate support for optical recognition of the blood unit.
Suitable for positioning 6 plates.
Hinged lid included.
SL9
Universal support for chromatographic plates made of stainless steel.
Capacity of 9 items. Suitable for positioning flat materials.
It takes up 1/2 the space of a standard basket.
SL18
Support for standard 20x20 chromatographic plates.
Capacity of 18 items. The guides are shaped in such a way that the
support points are outside the working surface.
31
BOTTLE Supports
PB50
Support for 56 wide-necked bottles of 50 ml (screw cap GL32 ISO4796
or ground cap DIN 12038 or non-standard cap).
Max bottle dimensions: diam. 46 mm - H 87 mm.
PB100 for 32 wide-necked bottles of 100 ml.
(screw cap GL45 ISO4796 or ground cap DIN 12038 or non-standard
cap). Max bottle dimensions: diam. 56 mm - H 100 mm.
PB250
Support for 25 wide-necked bottles of 250 ml.
PB500
PB1000
Test tube supports
Additional accessory for the standard baskets CS1-1 and CS2

and the trolley LM20 for washing analysis test tubes. It has a capacity
of approximately 160 standard test tubes with 3 removable
compartments and lid. It takes up a ¼ of the space of a standard basket
and is available in four standard sizes:
cP105: test tubes up to 75 mm in height
Petri dish supports
PD70S - 40 items, 50-70 mm positioned on the upper level CS1-1.

PD100S - 38 items, 70-120 mm positioned on the upper level CS1-1.
PD70I - 40 items, 50-70 mm positioned on the upper level CS2.
PD100I - 38 items, 70-120 mm positioned on the upper level CS2.
racks for small glassware,

baskets and holding nets
PF1/2
Additional accessory for CS1-1 and CS2 racks made from flat AISI 304
stainless steel mesh with small mesh openings as a rack to hold small
glass items or as rigid rack as an alternative to the Nylon holding nets.
Available in 3 versions: PF1 (not shown in the photo) bottom rack with
hole for positioning on the top level; PF2 (not shown in the photo) com-
plete bottom rack for positioning on the bottom level only; PF1/2 (shown
in the photo) half bottom rack for positioning on the upper level.
D-PF1 (only for GW2045)

Full bottom rack for upper carriage, made from stainless steel 10x10
mesh with central hole, for positioning on the upper carriage D-CS1.
D-PF2 (only for GW2045)

Full bottom rack for upper carriage, made from stainless steel 10x10
mesh with central hole, for positioning on the lower carriage D-CS1.
RC1
Holding nets with plastic-coated metal edges and Nylon ties to hold small
glass items in place in the standard baskets CS1-1 and CS2; available in
three models: RC1 fits in the whole basket, RC1/2 fits in half the basket,
RC1/4 fits in a quarter of the basket.
RC1/2 - RC1/4
Holding nets with plastic-coated metal edges and Nylon ties to hold small
glass items in place in the standard baskets CS1-1 and CS2; available in
three models: RC1 fits in the whole basket, RC1/2 fits in half the basket,
RC1/4 fits in a quarter of the basket.
33
BASKETS
CPF1
Complete bottom level basket with edging and handles.
Made of flat stainless steel mesh with mesh openings of 10x10 mm.
Dimensions l x d x h = 445x444x68 mm (height with handles 110 mm).
Positioning on the lower trolley CS2.
CPF1/2 (not shown in the photo): bottom level basket with edging and
handles. Made of flat stainless steel mesh with mesh openings
of 10x10 mm.
Dimensions l x d x h = 225x444x68 mm (height with handles 110 mm).
It takes up ½ the space of the lower trolley CS2.
CSK2
Baskets with stainless steel handles, suitable for
medium-sized instruments.
Mesh openings of 5x5 mm.
SPECIAL TROLLEYS
CSK-C
Stainless steel trolley with 3 washing levels for butchery utensils available
on request, suitable for positioning three SCL-23 knife and utensil
holders. Upper levels with spraying arm incorporated. Lower level with
sprayer at the bottom of the machine.
CPB1
Stainless steel upper trolley for wine-tasting glasses.
Suitable for washing 14 wine-tasting glasses of max. 220 mm in height.
CPB2
Stainless steel lower trolley for wine-tasting glasses.
Suitable for washing 14 wine-tasting glasses of max. 240 mm in height.
SPIGOTS
Injection spigots available in the following versions:

- spigot for 6% and 12% butyrometers
- Nylon spigot for pipettes
- Spigots for glassware with the following heights:
90, 110, 140, 160, 180, 220, 240, 260 mm.
narrow-necked glassware
injection carriages
LPM24 (only for GW2045 model)

Mixed stainless steel flask/pipette carriage with 12+12 positions,
suitable for washing narrow-necked glassware up to 490 mm in
height. Fitted with the following nozzles: 4 x U6240, 2 x U6220, 2
x U4160, 2 x U4140, 2 x U3110, 12 x LB40. Maximum glassware
height of 490 mm and positioning on the D-CS2 carriage lower
level.
LM24 (only for GW2045 model)

Universal 24-position stainless steel flask washer, suitable for
washing narrow-necked glassware up to 490 mm in height. Fitted
with the following nozzles: 6 x U6240, 5 x U6220, 6 x U4160, 5 x
U4140, 2 x U3110. Positioning on the D-CS2 carriage lower level.
LM22S (only for GW2045 model)

Universal 22-position stainless steel flask washer, suitable for
washing narrow-necked glassware up to 225 mm in height. Fitted
with the following nozzles: 12 x U4140, 5 x U3110, 5 x U390,
positioning on the D-CS1 carriage upper level.
35
INJECTION TROLLEYS
NARROW-NECKED GLASSWARE
LM20DS
20-position universal flask washing trolley in stainless steel with 20 spigots
and drying system connection. Suitable for washing and drying narrow-
necked glassware up to 490 mm in height. Half the trolley space is free
for mixed glassware suitable for a ½ basket accessory.
Positioning on the lower level.
LM20 (not shown in the photo): version without drying system
connection.
LM40DS
40-position universal flask washing trolley in stainless steel with 40 spigots
and drying system connection. Suitable for washing and drying narrow-
necked glassware up to 490 mm in height, flasks, round-bottom flasks
and graduated cylinders of various sizes. Positioning on the lower level.
LM40 (not shown in the photo): version without drying system connection.
LM40SDS
40-position flask washing trolley in stainless steel with forty U4140 spigots
and drying system connection. Suitable for washing narrow-necked
glassware up to 225 mm in height. Positioning on the upper level.
LM40S (not shown in the photo): version without drying system connection.
LM80DS
Two-level flask washing trolley with 68 U4140 spigots and 1 UC6 spigot
and drying system connection. Suitable for internal injection washing of
narrow-necked glassware with a maximum height of 225 mm. Positioning
on two levels.
LM80 (not shown in the photo): version without drying system connection.
N.B. The models with drying system connection (DS versiones) are specific for GW4090 and GW4060 glassware washers.
REACTOR WASHING
LR4DS
Stainless steel trolley with drying system connection.
Suitable for inside washing and drying of 3/5-way reactors
of maximum 3 litres or up to 12 narrow-necked glass items.
Fitted with 20 U6260 spigots. Positioning on the lower level.
LR4 (not shown in the photo): version without drying system connection.
FISCHER BOTTLE WASHING
LT20DS
Stainless steel trolley with drying system connection for washing
and drying of 12 Fischer bottles and graduated cylinders with a maximum
height of 55 cm. 6 positions for injection washing of narrow-necked
glassware. Fitted with 18 spigots. Positioning on the lower level.
LT20 (not shown in the photo): version without drying system connection.
BUTYROMETER WASHING
LB40DS
Stainless steel trolley for butyrometer washing with drying system
connection. Suitable for washing and drying of 40 butyrometers. Specify
the type of butyrometer in the order. Positioning on the upper level.
LB40 (not shown in the photo): version without drying system connection.
37
BOTTLE WASHING
LB4DS
Stainless steel trolley for washing large glass items with drying system
connection. Suitable for washing two 10-litre bottles + two 5-litre
Schott-type bottles. Fitted with 8 special spigots.
LBT5DS
Stainless steel trolley for bottle washing with drying system connection.
Suitable for washing and drying of five 5-litre bottles
(diam. 180 x h.500mm, max neck diameter 80 mm). Fitted with 5 special
spigots.
LBT5 (not shown in the photo). Version without drying system connection:
LBT5.
LB8DS
Stainless steel trolley for washing large glass items with drying system
connection. Suitable for washing 8 bottles of maximum 50 cm in height.
Fitted with 8 U6260 spigots and 8 special spigots.
LB32DS
Two-level stainless steel trolley for injection washing of bottles with drying
system connection. Suitable for washing 32 narrow- or wide-necked
bottles of 250-1000 ml, max. diam. 101 mm, H.245 mm. Fitted with 32
U6170 spigots.
Positioning on 2 levels.
LB1-20DS
Stainless steel trolley for washing universal large glass items with drying
system connection.
Positioning on lower level.
N.B. The models with drying system connection (DS versiones) are specific for GW4090 and GW4060 glassware washers.
PIPETTE WASHING
LPV40DS
stainless steel trolley for washing volumetric pipettes up to 55 cm in length.
20 positions for pipettes of 55 cm in height and 20 positions for pipettes
and/or flasks of 45-49 cm in height.
LPV40 (not shown in the photo): version without drying system
connection.
LPT100DS
Stainless steel pipette washing trolley with drying system connection
for washing and drying of 100 pipettes with a capacity of 1 to 20 ml
and a height up to 450 mm. The pipette washing disc is fitted in a trolley
to allow fast loading and unloading access.
LPT100 (not shown in the photo): version without drying system
connection.
vials and tapered centrifuge

test tubes
KP200DS
Trolley with drying system connection for washing of tapered
and cylindrical test tubes by internal injection. It has a maximum capacity
of 100 test tubes. Positioning on the upper washing level.
KP200 (not shown in the photo): version without drying system
connection.
mixed injection trolleys

(pipettes + narrow neck)
LPM2010DS
20-position stainless steel trolley with drying system connection for mixed
washing of flasks, pipettes and test tubes. Suitable for washing and
drying of 10 pipettes up to 55 cm + 20 narrow-necked glass items
+ ¼ free space to be filled with a CP series test tube basket. Fitted with
the following spigots: 2 x U6260, 2 x U6240, 2 x U6220, 3 x U4180, 2
x U4160, 2 x U4140, 3 x U3110, 4 x U390, 1 x UC6, 10 x ULB40 for
pipettes with a maximum height of 55 cm. Positioning on the lower level.
LMP2010 (not shown in the photo): version without drying system
connection.
LPM2020DS
Injection washing trolley with drying system connection for mixed
washing of pipettes and flasks with 20 positions for pipettes up to 550
mm in height and 20 positions for narrow-necked glassware with a
maximum height of 49 cm. Fitted with 38 spigots.
LPM20/20 (not shown in the photo): version without drying system
connection.
39
GW6090
RS232
GW6090 TECHNICAL FEATURES

Phase parameters type of water, detergent quantity, target temperature, extension time, drying temperature and time
Accuracy 0.1°C
Temperature sensors in tank 1 PT 1000 CLASS B IEC 60751
Dosing pumps 5 max
Alarm display 80
Password 4 levels
AUXILIARY FUNCTIONS
Waste water separation
solenoid valve control optional
Water quality check optional
DRYING SYSTEM
Drying fan yes
Drying heating element 4 kW
WATER SUPPLY
Cold/hot water inlet yes, max 42º F hardness
External water softener optional
Recirculation pump 2 pumps of 400 l/min
WATER HEATING
Water pre-heating via boiler yes
DIMENSIONS LxDxH mm
Outside 2035x801x902 (drying system versions) and 1835x801x902 (version without drying system)
Inside 670x650x835
Net weight (kg) 282
stainless STEEL
Wash tank AISI 316L
Max. voltage/power 3/N/PE 400V ~ 50Hz 18.5 kW
41
GW6090 OPTIONALS
WD-PRINT
Printer integrated in the panel.
WD-PAPER Thermal paper roll. Diameter 50 mm, width 57 mm.
WD-LS6090
Detergent level sensor. Allows controlling the level of liquid additives and
signals when the detergent has run out. Equipped with an adjustable
drawing tube for cans of different heights.
IC6000
Digital indicator to monitor wastewater conductivity. Particularly useful
when using demineralised water for final rinsing. If the wastewater has high
conductivity values it is suggested to execute further rinsing. Measuring
range between 0 and 1000 μs/cm. Value reading shown on a backlit LCD
display. Display of out-of-scale parameters. Built into the front panel of the
machine.
pad 2
drawn from a non-pressurised tank positioned on the ground.
GW6090 OPTIONALS
WD-FLUX FLOW METER FOR PERISTALTIC PUMPS

Allows controlling the quantity of additive the peristaltic pumps deliver.
Installed directly on the machine on each single detergent feed duct
leading into the tank. It signals any feeding malfunctions or when the
products run out by showing a warning on the display.
AD13
Additional peristaltic pump for feeding an additional additive complete
with level sensor. The quantity of detergent delivered by the pump is
directly controlled by the machine microprocessor.
WD-VDS
Double discharge valve that allows separating and ducting the polluted
wastewater from the first washing cycles from the final rinsing water.
This wastewater separation device is composed of 1 and 1/2” valves
with Viton membrane and valve opening is controlled by the machine
microprocessor.
43
GW6090 washing configuration
The strong point of the gw6090 washing system is that the direct injection systems can be exchanged
with the rotating sprayer systems on all three washing levels. By placing the 6 available systems on different levels,
many different configurations can be obtained, thus allowing loading capacity to by optimised according to washing
requirements. Glassware of various sizes with heights up to 790 mm and volumes up to 25 litres can be washed.
DIRECT INJECTION MAXIMUM ROTATING SPRAYER MAXIMUM

SYSTEMS HEIGHT OF SYSTEM HEIGHT OF
GLASSWARE (mm) GLASSWARE (mm)
3° LEVEL C63_L690 C62
telescopic base telescopic base with
Iinjection system 170 170 rotating sprayer 105 105
450 380
2° LEVEL C63_L680 C62
telescopic base telescopic base with
720 835
injection system 210 rotating sprayer 195
640
1° LEVEL C61_L685 C61
telescopic base with telescopic base using
rotating sprayer the rotating sprayer
260 260 545 at the bottom of the wash tank 365 365
45
three washing levels
direct injection
Level 1: C61 basic trolley with L685 direct injection system.
Maximum useful height 260 mm 76 spigots.
Level 2: C63 trolley with L680 direct injection system.
Level 3: C63 trolley with L690 direct injection system.
direct injection/ rotating sprayers

Level 2: C62 upper trolley with rotating sprayer.
Maximum useful height 150 mm, useful washing surface 625x625 mm.
Level 3: C63 telescopic support with L690 direct injection system.
rotating sprayers
Level 1: C61 basic trolley . Maximum useful height 325 mm.
Maximum useful height 195 mm.
Washing surface 625x625 (1.18m2 total).
two washing levels
direct injection
Maximum useful height 260 mm, 76 spigots.
direct injection and rotating sprayers

Level 1: C61 basic trolley. Maximum useful height 330 mm.
direct injection and rotating sprayers

47
TWO washing levels
rotating sprayers
Level 2: C62 telescopic base with rotating sprayer.
Washing surface 625x625 (0.78m2 total).
direct injection
direct injection/ rotating sprayers

ONE washing level
injection washing
rotating sprayers
Level 1: C61 basic trolley.
direct injection
This special C64 trolley can be used to wash drums with heights up to
530 mm and diameters up to 30 mm using spigots.
Trolleys can be developed for special applications on request.
Level 1: C64 basic trolley.
49
WASHING ACCESSORIES GW6090
LM6-10U
Stainless steel trolley for bottle washing with drying system connection.
Suitable for washing and drying large glasswares of different sizes.
PB6000
Support for wide-mouthed bottles. Capacity 25 flasks
from 1000 ml to 5000 ml and/or 1000 ml wide-mouthed bottles
cap). Made of stainless steel.
L685
Injection system for large, medium and small glassware
with 76 spigots of differing heights: 90/110/140/160/180/240 mm.
The differing spigot heights make it possible to optimise loading
of different sized glassware. This spigot configuration
allows the system to be used on washing levels 1 and 2.
L680
Injection system for small and medium glassware
with 76 spigots at the same height of 140 mm.
This spigot configuration makes it suitable for preferential
use on 2 work levels.
L690
Injection system for small glassware with 86 spigots
at the same height of 110 mm.
This spigot configuration makes it suitable for use
on the 3rd work level.
BASIC TROLLEYS GW6090
C61
Basic level 1 trolley with grid. It is used on its own and is suitable for
positioning various glassware supports. Washing is performed by the
internal sprayer at the bottom of the machine.
The C61 basic trolley is also used to position the injection systems (L685/
L680/L690) on level 1. The injector trolleys are inserted into the guide rails
of the C61.
C63
Telescopic support for injection systems. The support is used to
position the injection systems on levels 2 and 3.
The C63 is inserted into guide rails of the machine.
The injector trolleys (L680/685/690) are inserted in turn into the guide rails
of the C63. The system allows the injection systems to be completely
removed in order to simplify loading the glassware.
C62
Basic trolley with rotating sprayer for levels 2 and 3.
It is used on its own and is suitable for positioning
glassware supports.
The system is divided into 2 parts:
1. Base with sprayer
2. Telescopic support with top.
51
WATER TREATMENT
To obtain high quality washing standards, it is fundamentally important to used correctly treated water. In the prewash, washing and neutralisation phases, softened
water should always be used. Models GW2045, GW1060, GW4060, GW3060 and GW4090 range have an efficient built-in decalcifier capable of reducing the hardness
of the supply water so as to prevent the classic formation of whitish stains inside the chamber and on the instruments.
Smeg also supplies a range of high-performance WS water softeners which are compact and easy to install. Equally important is the rinsing of the instruments with
demineralised water in order to eliminate any contaminants remaining in the washing chamber. For this purpose, Smeg has the compact and efficient WP3000 mixed
resin bed demineraliser.
WP3000
Resin column water purifier
The WP3000 water purifier is used to produce deionised water at 0.8-1 μS/cm,
suitable for the final rinsing of instrument washers. The system uses mixed bed
resins (disposable) which can also retain silica. When the resins run out, they can
simply be replaced with the MI700WP kit.
The resin cartridge is made out of stainless steel, as is the entire machine.
Net capacity of cartridge: 15 litres.

Dimensions: l x d x h = 300x600x850 mm.
MI700WP
Anion/cation mixed bed resins kit for the WP3000 water purifier. Total exchange
capacity 42700 litres/°F* end of cycle at 5μS/cm (*Hardness in French degrees).
Supplied with used resin disposal bag.
WS9E, WS11E, WS14E, WS17E
Water treatment systems
The WSE series of appliances are technological water softeners capable of completely
eliminating lime from water.
The resins are regenerated using normal sodium chloride.
Available in versions with flow rates of up to 2700 litres/hour.
The models are fitted with an electronically controlled head which can be programmed
depending on the hardness of the water. They provide backflow regeneration based on
the volume of water (bearing in mind the resin saturation rate) and proportional brine in
order to optimise water and salt consumption.
WS9E WS11E WS14E WS17E

MAXIMUM FLOW RATE 1600 l/h (16.7 l/min) 1800 l/h (43 l/min) 2000 l/h (43 l/min) 2200 l/h (43 l/min)
NOMINAL FLOW RATE 1000 l/h (16.7 l/min) 1500 l/h (43 l/min) 1600 l/h (43 l/min) 1800 l/h (43 l/min)
RESIN CAPACITY IN LITRES 9 11 14 17
EXCHANGE CAPACITY (m3/°F) 54 66 84 102
CYCLE CAPACITY AT 40°F 1350 1650 2250 2700
PROGRAMMABLE RESIDUAL HARDNESS 0-10° F 0-10° F 0-10° F 0-10° F
REGENERATING AGENT TYPE NaCl SALT NaCl SALT NaCl SALT NaCl SALT
REGENERATING AGENT CONSUMPTION 0.9 kg/cycle 1.0 kg/cycle 1.2 kg/cycle 1.8 kg/cycle
DIMENSIONS ØxH (mm) 300 x 470 x 540 300 x 470 x 660 300 x 470 x 815 300 x 470 x 1070
SALT TANK DIMENSIONS L x P x H (mm) integrated integrated integrated integrated
CAPACITY LITRES (SALT) about 15 about 20 about 30 about 40
CONNECTIONS 1” 1” 1” 1”
53
DETERGENTS AND ADDITIVES
To achieve excellent washing results and optimise the thermal disinfection of laboratory instruments, specific detergents
should be used. Smeg has a complete range of alkaline detergents (for use during the washing phase) and neutralising
acid detergents (for use during the neutralisation phase) especially designed to guarantee efficient cleaning and optimise
the efficiency of the final thermal disinfection phase. Smeg also has numerous disinfectants designed for thermolabile
instruments and anaesthesia tools for use in the machine during the thermochemical cycle, as well as special lubricants
and additive that can lengthen the lifetime of the medical devices.
powder ALKALINE DETERGENTS
DETERGLASS
Universal powdered alkaline detergent.
10 kg pack
DETERGLASS SP
Universal powdered alkaline detergent, phosphate-free.
10 kg pack
liquid ALKALINE DETERGENTS
DETERLIQUID D
Liquid alkaline detergent.
10 litre container.
DETERLIQUID D2
Liquid alkaline detergent, phosphate-free.
5 litre container.
DETERLIQUID SP
Liquid alkaline detergent for
water and pharmaceutical analysis, phosphate-free. 5 litre container.
liquid Acid neutralisers
ACIDGLASS P
Liquid acid neutraliser for laboratory glassware.
5litre container.
ACIDGLASS P2
Liquid acid neutraliser for laboratory glassware.
5litre container.
ACIDGLASS C2
Neutralizing acid detergent.
5-liter container, phosphate-free
SPECIAL ADDITIVES
DRY CLEAN
Sspecial additive for promoting drying
after the rinse phases. 5litre container.
F1S
Silicon defoaming additive for petrol cycles, phosphate-free.
1 litre container.
55
EXTERNAL DIMENSIONS - BASIC LINE
GW2045 and GW1060 EXTERNAL DIMENSIONS
QUOTA GW2045 (mm) GW1060 (mm)

A 620 670
B 600 600
E 450 600
F 30 30
G 850 850
EXTERNAL DIMENSIONS - BASIC LINE
GW4060 EXTERNAL DIMENSIONS
QUOTA GW4060 (mm)

A 600
B 600
E 600
F 30
G 850
57
EXTERNAL DIMENSIONS - PROFESSIONAL LINE
* Height of built-in version.
* Height of built-in version.

EXTERNAL DIMENSIONS - PROFESSIONAL LINE
** Height of GW6090 model (without drying).
59
technical features - BASIC LINE
GW2045 GW1060 GW4060

Internal dimensions (LxDxH mm) 380x480x590 520x515x545 520x515x545
External dimensions (LXDXH mm) 450x620x850 600x650x850 600x605x850
(830 with built-in top) (830 with built-in top) (830 with built-in top)
Standard programmes stored 6 6 9

Modifiable programs 2 2 6
Detergent dosing system Powder dispenser or peristaltic Powder dispenser or peristaltic Powder dispenser or peristaltic
pump (as optional) pump (as optional) pump (as optional)
Neutralizing dosing pump type Peristaltic pump Peristaltic pump Peristaltic pump
Max nr. of dosing pumps 2 3 3
Possibility of volume detergent optional optional optional
control
Detergent cabinet n.a. optional optional
Display With segments and warning light With segments and warning light With segments and
communication led icons
Control panel Control buttons and program Control buttons and program Membrane keyboard
selector knob on the panel selector knob on the panel
Steam Condenser optional optional optional
Drying system Thermodynamic Thermodynamic Forced hot air through
“drying system”
Pre-filter class C n.a. n.a. yes

HEPA filter class S 99,999% n.a. n.a. optional
Cold water supply yes yes yes

Hot water supply no no no
Demineralized water supply yes yes yes
Integrated water softener yes yes yes

Washing pump 200l/min 400l/min 400l/min
Conductivity control n.a. n.a. n.a.
Trolleys Included yes, upper and lower standard no no
rack
Printer optional optional optional
Door interlock yes yes yes
Net weight (kg) 61 77 70
Conformity 2006/95/CEE, 93/68/CEE, 2006/95/CEE, 93/68/CEE, 2006/95/CEE, 93/68/CEE,
2004/108/CEE 2004/108/CEE 2004/108/CEE
Supply/Max Power 1/N/PE/230V- 50Hz-3,3kW 1/N/PE/230V- 50Hz-2,8kW 1/N/PE/230V- 50Hz-2,8kW
As an alternative: As an alternative:
3/N/PE/400V- 50Hz-7,0kW 3/N/PE/400V- 50Hz-7,0kW
Possibility of 60Hz supply yes yes yes
Equipped with plug yes no no
technical features - PROFESSIONAL LINE
GW3060 GW4090 GW6090

Internal dimensions (LxDxH mm) 520x515x545 520x515x545 670x650x835
External dimensions (LXDXH mm) 600x640x850 900x640x850 902x801x2035 (with drying system)
(830 with built-in top) (830 with built-in top) 902x801x1835
(without drying system)
Standard programmes stored 20 20 20
Modifiable programs 10 (expandable to 50) 10 (expandable to 50) 10 (expandable to 50)
Detergent dosing system Powder dispenser Peristaltic pump Peristaltic pump
or peristaltic pump
Neutralizing dosing pump type Peristaltic pump Peristaltic pump Peristaltic pump
Max nr. of dosing pumps 4 4 5
Possibility of volume detergent optional optional optional
control
Detergent cabinet optional yes yes
Display Backlit graphic LCD display Backlit graphic LCD display Backlit graphic LCD display
128x64 pixel 128x64 pixel 128x64 pixel
Control panel Membrane keyboard Membrane keyboard Membrane keyboard
Steam Condenser optional optional No

Drying system Thermodynamic Forced hot air through (as optional)
“drying system” Forced hot air through
“drying system”
Pre-filter class C n.a. yes yes
HEPA filter class S 99,999% n.a. optional optional
Cold water supply yes yes yes

Hot water supply yes yes yes
Demineralized water supply yes yes yes
Integrated water softener yes yes optional (externally)

Washing pump 400l/min 400l/min 2 x 400l/min
Conductivity control optional optional optional
Trolleys Included no no no
Printer optional optional optional

Door interlock yes yes yes
Net weight (kg) 76 83 282
Conformity 2006/95/CEE, 93/68/CEE, 2006/95/CEE, 93/68/CEE, 2006/95/CEE, 93/68/CEE,
2004/108/CEE 2004/108/CEE 2004/108/CEE
Supply/Max Power 1/N/PE/230V- 50Hz-2,8kW 1/N/PE/230V- 50Hz-2,8kW 3/N/PE/400V – 50Hz- 18,5kW
As an alternative: As an alternative:
3/N/PE/400V- 50Hz-7,0kW 3/N/PE/400V- 50Hz-7,0kW
Possibility of 60Hz supply yes yes yes
Equipped with plug no no no
61
NOTE
NOTE
This catalogue has been printed on FSC® - certified paper
(Forest Stewardship Council®) and cellulose produced from forest
managed responsible in accordance with strict environmental,
social and economic rules.
http://www.fsc.org/
Smeg S.p.A.
Instruments Division
Via L. da Vinci, 4, 42016 Guastalla (RE), Italy
Tel. +39 0522 8211 - Fax +39 0522 821592
E-mail: [email protected] - www.smeg-instruments.com
Smeg S.p.A. reserves the right to without prior notice make any modifications as it sees fit to improve its products.
INSTRUMENTS
Smeg S.p.A.
Via Leonardo da Vinci, 4 - 42016 Guastalla (RE) - Italy
06/2012
E-mail: [email protected] - www.smeg-instruments.com

Instruments: Washing Disinfection Catalogue

Uploaded by

Copyright:

Available Formats

Instruments: Washing Disinfection Catalogue

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Instruments: Washing Disinfection Catalogue

Uploaded by

Copyright:

Available Formats

INSTRUMENTS

washing and disinfection

Smeg Instruments page 4

Why choose a Smeg glassware washer? page 6

Washing volumes page 8

Technical features: symbols page 12

Basic line: GW2045, GW1060, GW4060 page 14

Professional line: GW3060, GW4090 page 20

Glassware washer optional page 24

GW2045 Configuration page 26

GW1060,4060,3060,4090 Configuration page 28

Professional line: GW6090 technical data sheet page 40

GW6090 optionals page 42

GW6090 configurations page 44

GW6090 accessories page 50

Water treatment page 52

Detergents and additives page 54

External dimensions page 56

Machines technical features page 60

SERVICE INNOVATION QUALITY RELIABILITY

VAST RANGE AUTOMATIC WASTEWATER

DISINFECTION CONTROLLED PROGRAMMABLE

The Smeg disinfection Washing effectiveness is The heart of the new-

GW4060 is designed to operate with 1 or 2 levels for

GW3060 is designed to operate with 1 or 2 GW4090 is designed to operate with 1 or 2

GW6090 is a machine with a high loading capacity

PROGRAMMABLE assures “intelligent” management ADDITIONAL

LAN CONNECTION CONNECTION STEAM

OPTIONAL OPTIONAL OPTIONAL

GW2045 technical features All versions

OPTIONAL OPTIONAL OPTIONAL OPTIONAL

GW1060 technical features All versions

OPTIONAL OPTIONAL OPTIONAL OPTIONAL

GW4060 technical features All versions

OPTIONAL OPTIONAL OPTIONAL OPTIONAL

GW3060 TECHNICAL FEATURES All versions

OPTIONAL OPTIONAL OPTIONAL OPTIONAL

GW4090 TECHNICAL FEATURES

STAINLESS STEEL BASES AND FRAMES

TWO SPRAYING LEVELS

TWO SPRAYING LEVELS

ONE INJECTION LEVEL

TWO SPRAYING/INJECTION LEVELS

ONE MIXED INJECTION LEVEL

TWO SPRAYING/INJECTION LEVELS

TWO INJECTION LEVELS

TWO SPRAYING LEVELS

TWO SPRAYING/INJECTION LEVELS

ONE SPRAYING/INJECTION LEVEL

ONE INJECTION LEVEL

TWO INJECTION LEVELS

ONE MIXED INJECTION LEVEL

D-CS1 (only on GW2045 model)

CS1-1 (not in photo)

D-CS2 (only on GW2045 model)

CS2 (not in photo)

Flask and beaker supports

SB9 (only on GW2045 model)

SB14 (only on GW2045 model)