Scribd
Upload
89 views2 pages

Set A Workshop

The document is a practice exam for a workshop technology course, containing 20 multiple choice questions testing various concepts. Some key topics covered include: identifying marking and measuring tools; properties of materials like stainless steel, cast iron, and bronze; machine tools and their functions like lathes, drills, and taps; metalworking processes like hardening, welding, and casting; and material properties like machinability, hardness, modulus of elasticity, ductility, and malleability. The exam is for a Bachelor of Engineering program's first year/part one and has a full mark of 10 and pass mark of 4 over 10 minutes.

Uploaded by

विशाल पुडासैनी
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
89 views2 pages

Set A Workshop

The document is a practice exam for a workshop technology course, containing 20 multiple choice questions testing various concepts. Some key topics covered include: identifying marking and measuring tools; properties of materials like stainless steel, cast iron, and bronze; machine tools and their functions like lathes, drills, and taps; metalworking processes like hardening, welding, and casting; and material properties like machinability, hardness, modulus of elasticity, ductility, and malleability. The exam is for a Bachelor of Engineering program's first year/part one and has a full mark of 10 and pass mark of 4 over 10 minutes.

Uploaded by

विशाल पुडासैनी
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

KATHMANDU ENGINEERING COLLEGE Exam Final Assessment

KALIMATI, KATHMANDU Level B. E. Full Marks 10


2072 Program BCE A Pass Marks 4
Year/Part I/I Time 10 min

Workshop Technology

Attempt all questions Set : A

1. Which of the following is a marking tool?


a. scriber c. surface plate
b. scraper d. Try-square

2. The principle components of stainless steel are:


a. Cr and Mg c. Ni and Mg
b. Cr and Ni d. None of the above

3. Which of these is not a machine tool?


a. lathe c. Drilling
b. shaper d. Vice

4. In lathe machine
a. job is stationary and tool rotate c. both job and tool rotate
b. tool is stationary and job rotate d. both a and b

5. Which one of following has reciprocating motion


a. Lathe b. Drilling
c. Shaper d. None of the above

6. Which one of the following is used to stabilize the structure of metal after hardening
a. Annealing b. Tempering
c. Quenching d. Cooling in oil

7. Tail stock
a. is situated at right hand end of the bed
b. Supports the work when turning on centre.
c. is used for holding and feeding the tools such as drills, reamers, tap etc.
d. all of the above

8.Knurling is done in a job piece in order to provide ……………….. to a material

9. The ability of material to resist the scratching, abrasion, indentation or penetration is


called
a. Hardness c. Toughness
b. Rigidity d. None of the above
10. The tool used to make the threads inside the drilled hole is called
a. Reamer c. Tap
b. Die d. None of the above

11. Which of these measuring tools has high precision?


a. Steel Rule c. Protractors
b. Divider d. Vernier calipers

12. Ratio of stress to strain, within elastic limit is called


a. Young’s modulus of elasticity c. Modulus of rigidity
b. Bulk modulus of elasticity d. All of the above

13. Machinability of cast iron compared to that of steel is


a. Less c. Greater
b. Equal d. Not comparable

14. Bronze is an alloy of copper and tin in which the percentage of


a. copper is greater c. copper and tin is equal
b. tin is greater d. Either a or b or c

15. The workshop where the casting is done is called


a. Foundry shop
b. Machine shop
c. Carpentary shop
d. Welding shop

16. The process of reducing diameter of the work piece in lathe operations is called
a. Facing c. Turning
b. Spinning d. Rolling

17. Which of these is not a sheet metal operation


a. Shearing c. Seaming
b. Notching d. Reaming

18. During oxy-acetylene gas welding, oxidizing flame is produced when the percentage of
oxygen is
a. 75% c. 25%
b. 50% d. 20%

19. The capacity of material to absorb energy elastically is called …………...............

20. The property of material to be flattened into thin sheets without cracking by cold or hot
working is called
a. Ductility c. Malleability
b. Resilience d. Toughness

You might also like