Generator Protection

Some Review Slids

Generator Protection

2
Generator

3
 Generator Protection Review

Abnormal Operating Conditions

4
Abnormal Operating Conditions

Overexcitation
Over Open
Power Loss of Field
Loss of Field Circuits
Overexcitation
Overexcitation

Exciter
The
"Wild"
G Power
System
Abnormal
Inadvertent Frequency
Abnormal Energizing,
Frequency Pole Flashover
Loss of
Reverse Breaker Synchronism
Power Failure

5
Generator Stator Phase Fault
Protection (87G)

6
Over fluxing Protection (V/Hz) (24)
Causes:
• As voltage rises above rating leakage flux increases
• Leakage flux induces current in transformer support structure causing rapid localized heating.
Volts per Hertz Limiter and Protection:
• used to protect generator and step-up transformer from damage due to excessive magnetic flux resulting from low
frequency and/or overvoltage
• excessive magnetic flux, if sustained, can cause overheating and damage the unit transformer and the generator
core
• V/Hz limiter (or regulator) controls the field voltage so as to limit the generator voltage when V/Hz exceeds a
preset value
• V/Hz protection trips the generator when V/Hz exceeds the preset value for a specified time
 Over fluxing Protection (V/Hz) (24) Ct.
• Over excitation (Fluxing) occurs when the V/Hz ratio exceeds 105% at FL and
110% at no load
• V/Hz relays set at 110% with a 5 – 10 sec delay
• Generator overvoltage can occur without exceeding V/Hz relay setting due to
large over speed on hydro generator
 81O/U (Over/Under Frequency Protection)
Over Frequency :
• Significant load rejection
• Should use for protection against possible over speeding condition
• Can cause Overvoltage on hydro turbines
Under frequency:
• Over load condition
• Loss of Generation
• Can cause Over excitation
• Can cause turbine blade fatigue
 Out of Step Protection (78)
• High peak currents and off-frequency operation can occur when a generator losses
synchronism.
• Causes winding stress, high rotor iron currents, pulsating torques and mechanical
resonances.
• It will protect generator against pole slipping.
 Negative Sequence Protection (46)
Causes:
• Unbalance load condition
• Unbalance fault
Effect:
• Negative sequence current interacts with normal positive sequence current to induce a double frequency current (120 Hz)
• Current (120 Hz) is induced into rotor causing surface heating
• Generator has established short-time rating, 𝐾 = 𝐼2 𝑡
Where
K=Manufacturer Factor (the larger the generator the smaller the K value)
I= Negative sequence current
• Protects generator from excessive heating in the rotor due to unbalanced stator currents
• Rotor temperature rise proportion to I
 System Backup Protection (51V, 21)
• Common practice to provide protection for faults inside and outside of the generator zone of
protection
• It will use as back up for 87G
• Distance relay (21) set to include generator step up transformer and reach beyond, into the
system (zone 1 for internal faults and zone 2 for external faults)
• Time delays must be coordinated with those of the system protection to assure that system
protection will operate before back up
• Control or restraining function in 51V used to prevent or desensitize the overcurrent relay
from tripping until the generator voltage is reduced by a fault (80% of nominal voltage)
 Synchronizing (25)
• Improper synchronizing of a generator to a system may result in damage to the generator step-up
transformer and any type of generating unit.
• The damage incurred may be slipped couplings, increased shaft vibration, a change in bearing alignment,
loosened stator windings, loosened stator laminations and fatigue damage to shafts and other mechanical
parts.
• In order to avoid damaging a generator during synchronizing, the generator manufacturer will generally
provide synchronizing limits in terms of breaker closing angle and voltage matching:
• Breaker closing angle: within ± 10 elect. degrees
• Voltage matching: 0 to +5%
• Frequency difference < 0.067 Hz
 Reverse Power (32)
• Prevents generator from motoring on loss of prime mover
• From a system standpoint, motoring is defined as the flow of real power into the
generator acting as a motor.
• With current in the field winding, the generator will remain in synchronism with the
system and act as a synchronous motor.
• A power relay set to look into the machine is therefore used on most units.
• The sensitivity and setting of the relay is dependent upon the type of prime mover
involved.
 Reverse Power (32) Ct.
Pickup setting should be below the following motoring limits:
• Gas : 50% rated power; time < 60 s
• Diesel : 25% rated power; time < 60 s
• Hydro turbines : 0.2% - 2% rated power; time < 60 s
• Steam turbines : 0.5% - 3% rated power; time < 30 s
Loss of Field Loss of Field (40)
CAUSES
• Field open circuit
• Field short circuit
• Accidental tripping of field breaker
• Regulator control failure
• Loss of main exciter
• If the field breaker is opened, the generator will act as an induction generator (receive
reactive power from the grid).
 Split Phase Differential (50DT)
• Most turbine generators have single turn stator windings. If a generator has stator
windings with multi-turn coils and with two or more circuits per phase, the split-
phase relaying scheme may be used to provide turn fault protection.
• In this scheme, the circuits in each phase of the stator winding are split into two
equal groups and the currents of each group are compared.
• A difference in these currents indicates an unbalance caused by a single turn fault.
Split-Phase Differential Phase Differential
 Split Phase Differential (50DT) Ct.
• Scheme detects turn to turn fault not involving ground.
• Generator must have two or more windings per phase to apply scheme.
• Used widely on salient-pole hydro generators. Used on some steam generators.
• Difference between current on each phase indicates a turn to turn fault.
• Need to have separate pick-up levels on each phase to accommodate practice of
removal of shorted terms.
 Inadvertent Off Line Generator Protection (50/27)(50AE)
Protects against closing of the generator breaker while machine is not spinning / on turning gear
Causes:
• Operating errors
• Breaker head flashover
• Control circuit malfunctions
• Combination of above
Inadvertent energizing is a serious industry problem:
• Damage occurs within seconds
• Conventional generator protection will not provide protection
 Generator Response and Damage to Three -Phase Inadvertent
Energizing
• Generator behaves as an induction motor
• Rotating flux induced into the generator rotor
• Resulting rotor current is forced into negative sequence path in rotor body
• Machine impedance during initial energizing is equivalent to its negative sequence
impedance
• Rapid rotor heating occurs 𝐾 = 𝐼2𝑡
 Over-Voltage (59)
• Generator overvoltage may occur without necessarily exceeding the V/Hz limits of
the machine.
• Protection for generator overvoltage is provided with a frequency-compensated (or
frequency insensitive) overvoltage relay.
• The relay should have both an instantaneous unit and a time delay unit with an
inverse time characteristic.
• Two definite time delay relays can also be applied.
 Large Machine Protection
IEEE C37.102

• Unit Connected
• High Z Grounded

32 Reverse Power
40 Loss of Excitation
46 Negative Sequence
49 Thermal Overload
51V voltage restraint
51G Ground overcurrent
64 Ground Relay
87 Differential

22
 References

• IEEE generator protection guide

23