Part 2: Brittle Deformation and Faulting: 12.113 Structural Geology

12.
113 Structural Geology

Part 2: Brittle deformation and faulting
Fall 2005
Contents
1 Brittle material behaviour 5
1.1 Reading assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.2 Failure criteria . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.2.1 Tensile stress . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.2.2 Shear fractures in noncohesive material . . . . . . . . . . . . . . 6
1.3 Cohesive material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.4 Effect of pore fluid pressures . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.5 Review questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2 Faults – General 9
2.1 Reading assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.2 Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.3 Stress distributions, faulting and tectonic setting . . . . . . . . . . . . . 9
2.4 Slides . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3
4
Chapter 1
Brittle material behaviour
1.1 Reading assignment

Twiss and Moore’s chapter nine is essential reading for this stuff, and parts of chapter
ten are definitely relevant.
1.2 Failure criteria

1.2.1 Tensile stress
σ1 = σ2 >> σ3
And σ3 is negative. Open tension fractures containing σ1 and σ2 and perpendic

ular to σ3 .
Draw a Mohr circle for this situation:
S1
shear
stress
S3
S2 extension fractures
open parallel to sigma
3 !!
normal
stress
Figure 1.1: Mohr construction for tensile stresses
5
1.2.2 Shear fractures in noncohesive material
For instance, loose sand. Byerlee in the 50s conducted various experiments look
ing at the strength of these sorts of materials, where strength is understood as the
amount of shear stress necessary to initiate motion, given a certain amount of nor
mal stress. If you plot shear stress necessary to initiate motion against normal stress,
you get a line which makes an angle φ with the normal stress axis. The equation de
scribing this relationship is Byerlee’s law, and written as
τc = σN tan φ = µσN
where φ is called the angle on internal friction and µ is the coefficient of fric
tion. We can create a Mohr construction that illustrates how this equation provides
a physical law for predicting when failure will occur in a material:
Figure 1.2: Mohr construction for shear failure according to Byerlee’s law (no cohe
sion). As an exercise, label the figure with τ, σN , 2α, α, σ1 , σ3 , and phi . Also, use
this diagram to derive the relationship α = 45 + φ/2
1.3 Cohesive material

Given the above failure criterion, in the absence of a confining stress, the shear stress
for failure will be zero. But materials have strength even in the absence of confining
stress – this is known as the cohesion. A modified failure criterion incorporating this
is the MohrCoulomb failure criterion:
τ = C + σN tan φ
Draw the Mohr circle construction for this.
6
shear
stress
lope
ve
en
lure
fai
fluid pressure
normal
stress
Figure 1.3:
1.4 Effect of pore fluid pressures

The effect of a pressurized fluid on a fault plane is to decrease the normal stress by
that pressure. In this case, the MohrCoulomb failure criterion becomes
τ = C + σN e f f tan φ = C + (σN − P f ) tan φ
where P f is the fluid pressure. On a Mohr diagram, the effect of fluid pressure is to
shift the Mohr circle to the left of the diagram. As fluid pressures go up, the possibil
ity that the Mohr circle intersects the failure envelope is increased.
1.5 Review questions

Lab 1 on stress, particularly the orientation of principal stresses in relation to fault
types and tectonic environments. Lab 5 on faults, particularly the problems on
joints and Downie’s slide.
What does a generalized failure envelope taking into account both tensile and
shear failure look like?
In general, what is the effect of higher mean stress (pressure)? What implications
does this have for the brittle failure of materials at greater and greater depths?
7
8
Chapter 2
Faults – General
2.1 Reading assignment

Chapter 4 is essential reading. There’s a lot of terminology: I suggest you make a
glossary for yourself, adding little cartoons helps, too.
For the discussion of stress distributions, see section 10.9, pages 202 – 205.
2.2 Terminology
For the following terms, write yourself a definition, or, better, draw a cartoon or find
a representative figure.
slip vs. separation
slickensides, slickenlines
fault scarps, faultline scarps
breccia, gouge.
conjugate faults
Drag folds, shift.
Dipslip faults: reverse (thrust), normal. Strikeslip faults: rightlateral, leftlateral.
2.3 Stress distributions, faulting and tectonic setting

Rock mechanics and Anderson’s theory of faulting give us a first order picture of
how the types and orientations of faults are related to the orientations of principal
stresses. In particular, this was the subject of an exercise in the first lab on stress,
and in the lab about faults. The idea follows from the results of rock deformation ex
periments, where it has been observed that shear fractures occur as conjugate sets
such that the greatest principal stress bisects the conjugate shear fractures. Since
the Earth’s surface must be a principal plane of stress (no shear stresses are trans
mitted across the Earth’s surface), Anderson fault theory predicts that normal faults
occur where the greatest principal stress is vertical, thrust faults occur where the
least principal stress is vertical and strikeslip faults occur where both greatest and
least principal stresses are horizontal. Since the greatest principal stress is usually
at an acute angle to the shear fractures, this also predicts that normal faults ought
to be steep, and thrusts are shallow. However, there definitely are steep thrust faults
(reverse faults) and very low angle normal faults. Part of this results from the in
herent uncertainty and imprecision of the MohrCoulomb model of fault formation,
but part of it has to do with the fact that stress orientations ought to change with
depth.
9
Figure 2.1: From Twiss and Moore, see textbook for discussion
Consider a "free body" diagram where a compressive tectonic stress is added to

the standard state of stress (pressure due to rock thickness increases linearly with
depth). If this stress is sufficiently high, you will get faulting, but stress trajectories
are straight lines. More importantly, if you consider the addition of shear stresses at
the base, much more interesting stress orientations result. Horizontal shear stresses
have to be balanced by vertical shear stresses and all shear stresses must vanish at
the surface. The result is that the free body diagram shows curved stress trajectories
and a much wider variety of predicted fault orientations. As an exercise, take the
diagrams of stress trajectories and draw on the expected orientations of faults.
2.4 Slides
For each of the slides, take a pen and draw on the fault or faults, and interpret them:
what kind of fault, active or not, what kind of structure. Can you tell slip or just sep
aration? Write a caption for each figure.
10
Figure 2.2:
Figure 2.3:
11
Figure 2.4:
Figure 2.5: The San Andreas fault
12
Figure 2.6: Faulted alluvial material.
Figure 2.7: Sagpond on active fault.
13
Figure 2.8: Note that the fault surface is not quite planar. The cylindricity of the fault
surface is an important indicator of the kinematics of motion
14
Figure 2.9: Slickensides
Figure 2.10: Fault gouge
15
Figure 2.11: Huge thickness of gouge at Tucki mountain, Death Valley, CA.
16
Figure 2.12: Mylonite. Fault gouge, fracture and fault breccia are all expressions of
brittle failure. Mylonites are produced by ductile deformation mechanisms and are
the deep, hot equivalent of brittle faults.
Figure 2.13: The Keystone fault
17
Figure 2.14: Another view of the Keystone fault. Red rocks are the Jurassic Aztec
sandstone. Dark grey rocks are the Cambrian Bonanza King dolostone. What is the
nature of the contact? What is the direction of transport?
18

Part 2: Brittle Deformation and Faulting: 12.113 Structural Geology

Uploaded by

Copyright:

Available Formats

Part 2: Brittle Deformation and Faulting: 12.113 Structural Geology

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Part 2: Brittle Deformation and Faulting: 12.113 Structural Geology

Uploaded by

Copyright:

Available Formats

12.

113 Structural Geology

1 Brittle material behaviour 5

1.1 Reading assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.2 Failure criteria . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.2.1 Tensile stress . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.2.2 Shear fractures in non­cohesive material . . . . . . . . . . . . . . 6

1.3 Cohesive material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.4 Effect of pore ﬂuid pressures . . . . . . . . . . . . . . . . . . . . . . . . . 7

1.5 Review questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.1 Reading assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.3 Stress distributions, faulting and tectonic setting . . . . . . . . . . . . . 9

Brittle material behaviour

1.1 Reading assignment

1.2 Failure criteria

And σ3 is negative. Open tension fractures containing σ1 and σ2 and perpendic­

Figure 1.1: Mohr construction for tensile stresses

1.3 Cohesive material

Draw the Mohr circle construction for this.

1.4 Effect of pore ﬂuid pressures

τ = C + σN e f f tan φ = C + (σN − P f ) tan φ

1.5 Review questions

2.1 Reading assignment

2.3 Stress distributions, faulting and tectonic setting

Consider a "free body" diagram where a compressive tectonic stress is added to

Figure 2.5: The San Andreas fault

Figure 2.6: Faulted alluvial material.

Figure 2.7: Sag­pond on active fault.

Figure 2.9: Slickensides

Figure 2.10: Fault gouge

Figure 2.13: The Keystone fault

You might also like

1.2.2 Shear fractures in noncohesive material . . . . . . . . . . . . . . 6

And σ3 is negative. Open tension fractures containing σ1 and σ2 and perpendic

Figure 2.7: Sagpond on active fault.