Opto-Switch: Dimensions

Download as pdf or txt
Download as pdf or txt
You are on page 1of 2

Back

Opto–Switch EE–SX460–P1

Transmissive
Photo–IC output.
Snap-in mounting model.
Mounts to 0.8- to 1.6-mm-thick panels.
With a 5-mm-wide slot.
Photo IC output signals directly connect to
C-MOS and TTL.
Connects to Omron EE–I005 and AMP’s EI
series connectors

Dimensions
171926-3 Terminal No. Name
(Japan AMP) Internal Circuit V Supply voltage
V (Vcc)
Optica O
l axis O Output (OUT)
G G Ground (GND)

0.5 (slit
Unless otherwise specified, the
width) tolerances are as shown below.
171826-3
Two, (Japan AMP) Optical
R1 axis Dimensions Tolerance
15±0.2 3 mm max. ±0.3
3 t mm v 6 ±0.375
Mounting
face 6 t mm v 10 ±0.45
10 t mm v 18 ±0.55
18 t mm v 30 ±0.65

Recommended Connectors:
Japan AMP 171822-3 (crimp-type connector)
172142-3 (crimp-type connector)
OMRON EE-1005 (with harness)

Specifications
Absolute Maximum Ratings (Ta = 25°C)
Item Symbol Rated value
Supply voltage VCC 10 V
Output voltage VOUT 28 V
Output current IOUT 16 mA
Permissible output dissipation POUT 250 mW (see note)
Operating temperature Topr –20°C to 75°C
Storage temperature Tstg –40°C to 85°C
Soldering temperature Tsol ---
Note: Refer to the temperature rating chart if the ambient temperature exceeds 25°C.
EE–SX460–P1 EE–SX460–P1

Electrical and Optical Characteristics (Ta = 25°C, VCC = 5 V±10%)


Item Symbol Value Condition
Current consumption ICC 30 mA max. With and without incident
Low-level output voltage VOL 0.3 V max. IOUT = 16 mA with incident
High-level output voltage VOH (VCC x 0.9) V min. VOUT = VCC without incident, RL = 47 kΩ
Response frequency f 3 kHz min. VOUT = VCC, RL = 47 kΩ (see note)

Note: The value of the response frequency is measured by ro- Disk


tating the disk as shown below.

2.1 mm

0.5 mm 0.5 mm
t = 0.2 mm

Engineering Data
Output Allowable Dissipation vs. Sensing Position Characteristics
Ambient Temperature Characteristics (Typical)
Output allowable dissipation Pc (mW)

d1 = 0±0.3 mm VCC = 5 V
Ta = 25°C
RL = 47 kΩ
Output transistor

Center of optical axis

Light interrupting plate

Ambient temperature Ta (°C) Distance d (mm)


EE-1005 Connector
1,000±20

(1) (2) (3)

No. Name Model Quantity Maker Wiring


1 Receptacle 171822-3 1 Japan Connector circuit no. Lead wire color
housing AMP 1 Red
2 Receptacle 170262-1 3 Japan 2 Orange
contact AMP
3 Yellow
3 Lead wire UL1007 AWG24 3 ---

Recommended Mounting Hole Dimensions and Mounting and Dismounting Method

Center of sensing
slot
Optical axis

Sensor edge Sensor edge on


connector side

The Opto–Switch can be mounted to 0.8- to 1.6-mm-thick panels.


Refer to the above mounting hole dimensions and open the mounting holes in
the panel to which the Opto–Switch will be mounted.
Insert into the holes the Opto–Switch’s mounting portions with a force of three
to five kilograms but do not press in the Opto–Switch at one time. The Opto–
Switch can be easily mounted by inserting the mounting portions halfway and
then slowly pressing the Opto–Switch onto the panel.

Dismounting is achieved by either hand (below panel), or screwdriver ( above


panel).

You might also like