SURFACE MINING | 189

PAYLOADS ANALYSIS

USING TELEMETRY
PAYLOADS ANALYSIS USING TELEMETRY
L.A.C. Teixeira, J.C. Koppe, E.Munaretti, V.Fernandes

*L.A.C. Teixeira¹, J.C. Koppe1, E.Munaretti¹, V.Fernandes²

¹UFRGS –Federal University of Rio Grande do Sul, Bento Gonçalves,9500
Porto Alegre, RS, Brazil
(*Corresponding author: [email protected])

²VALE S.A – Itabira Mine Complex

Serra do Esmeril, Minas Gerais, Brazil

October 18-21, 2016 • Rio de Janeiro /RJ • Brazil

190 | 24th WORLD MINING CONGRESS PROCEEDINGS

PAYLOADS ANALYSIS USING TELEMETRY

ABSTRACT

The actual iron ore price forces the companies to reduce costs in all production steps of the
mining operation. Loading and hauling materials using shovel-truck system represents the highest
mining costs, particularly tires, diesel, maintenance and workforce. Annual goals of materials
movement are split by months were weather conditions can affect productivity and performance of the
fleet. The data file of the monthly material movement is based on the scale of each truck. Every fleet
has a payload and it represents the capacity of hauling, being the value of loading a unique input
extracted in each duty cycle, without taking into account the position of the material over the truck’s
dump. Shear forces and torsion are applied all time at the frames trucks and, when the truckloads are
unbalanced, increases the forces over the frame and tires. Transport unbalanced truckloads into long
distances attack the tires and decrease its end of life, causing damages like displacement of tread and
flank separation. The objective of this study is to propose a methodology to decrease unbalanced truck
loads reducing the mining costs. In this mission of incorporating a material position on the truck´s
dump, the telemetry was taking into consideration. The analysis of the suspension pressures data
values shows the truckloads positions and with this data was created a databank. This databank
indicates that the operators need truck load training to reduce unbalanced loads and truck costs in the
mining operation, since unbalanced loads leads to early tires and suspensions scrap. The case study
was carried out at Itabira Iron Ore Mine Complex, Brazil. This methodology was able to reduce the
number of unbalanced truck loads as well as the tires life was increased.

KEYWORDS

Load and haul; off road trucks; unbalanced truckloads; mining; costs, off road tires.

INTRODUCTION

The loading and hauling costs control is important particularly in a scenario of reduced iron ore
price market. A common practice in large operation is hauling materials using shovel/trucks system,
therefore, costs with tires, components, suspensions and frames maintenance cracks due repetitive
efforts are very significant (Chamanara, 2013). Knowing and describing the operating parameters is
extremely important to understand the main causes of scrapping or early withdrawal of tires in
operation, among which are (Tire Maintenance Manual – Good Year/Off the road, 2008):

• Inflation pressure of tires and operation value;

• Temperature;
• Conditions of access - presence blocks, ripples, and sub- and over- elevation of roads;
• Transport speed;
• Average distance covered per cycle;
• Payload centering on the bucket trucks.

Tire consumption in an open pit mine is directly linked to the operating conditions in which they
are submitted. Unbalanced truck loads and tires in operation with low pressure lead to displacement or
separation of the inner layers of the tires by heating its internal structures. Shear forces and torsion are
applied all time at the frames trucks and, when the truckloads are unbalanced, increases the forces over
the frame and tires. Transport unbalanced truckloads into long distances attack the tires and decrease
its end of life, causing damages like displacement of tread and flank separation (Michelin Guideline –
Utilization and Maintenance – 2012).
 SURFACE MINING | 191

An important factor that should be taken into consideration for trucks tires is the TKPH (“tons
kilometers per hour”). To calculate this factor is taken into account three variables: distance traveled,
average speed and payload carried. For specification, TKPH admit that the materials transported
during the cycles are evenly distributed over the truck structure. The correct load centralization on the
bucket truck has its importance at this point in ensuring that each tire is carrying an approximate load
of their maximum capacity, without damage the truck’s productivity (payload). If large amounts of off-
center loads (Figure 1) are brought into a set of tires in constant cycles, they are subject to more severe
conditions, shortening the life thereof (Otraco, 2002).

Figure 1: Iron ore decentralized load image at Itabira mines, Brazil.

Analysis of the suspension pressures data values with telemetry can show the truck loads
positions and with this data was created a databank. This databank was used for operators training with
the goal to reduce unbalanced truck loads and reduce the truck costs in the mining operation, once
unbalanced loads can bring discomfort to the truck drivers as well as scrap early tires and suspensions.

METHODOLOGY

Key Performance Indicators for Load Position

The key performance indicators for truck load positioning are rack, roll and pitch (Figure
2). Rack is the twisting force and it is common to find the term torsional motion for its description.
Torsional forces applied constantly on trucks structures lead to cracking and potential repetitions may
decrease equipment life and is a major cause of premature breakage of components and chassis
(Chamanara, 2013).

Figure 2: The interactions between the suspension pressure values. a) Rack, b) Roll and c) Pitch. LF –
left front pressure suspension value, RF – right front, LR – left rear and RR – right rear.

The calculation of the rack value is given by:

192 | 24th WORLD MINING CONGRESS PROCEEDINGS

RACK = (LF + RR) – (RF + LR) Figure 2 – A

Roll (bias) is understood as the difference between the sums of the suspensions on the right
side by the sum of the suspensions on the left. This indicator reflects directly the positioning of loads
due to the comparison between the sides. As it must seek centralized loads, the values of the key
performance indicators (KPI’s) in each transmission cycle is expected to be null or close to zero,
reflecting little twisting force applied to the equipment during the hours of operation.

Roll calculation:

ROLL = (LF + LR) – (RF + RR) Figure 2 - B

Therefore, like the rack KPI it is also expected a value close to zero for roll, reflecting little
lateral difference between the pressures of the suspensions. The third and final KPI, the pitch, is
expected to find value equal to the difference between axes by subtracting the sum of pressures found
on the front axle by the values of both rear suspensions, as shown in Figure 2. Generally, for each tire
carrying or supporting the same load, the division of the total gross weight of operation should be 1/6
per tire. Thus, as the tire assembly has a ratio of one to two, comparing the front and rear axles, the
rear axles supports 2/3 (67%) of the total load and the front axles the remaining 1/3 (33%). The
calculation for pitch is:

PITCH = (LF + RF) – (LR + RR) Figure 2 - C

This difference between axes, when the payload is evenly distributed over the truck structure
is 1/3 negative of the sum of the values found in all four suspensions, reflecting that the load is
balanced across wheelbase (Chamanara, 2013). Chamanara explains how to compare the suspensions
pressure data by collecting data via telemetry and graphically displays the values over time of a
transport cycle (Figure 3).

Figure 3: suspensions pressures (tons) registration of a CAT truck in operation (Chamanara, 2013).

The current practice of mining companies is exclusively to extract the truck payload to build the
total movement at the end of each month, year or other period of interest. This work paper applies a
methodology of registering the distribution of loads on the bucket trucks thus creating a database with
these records. The database includes some information and describes the profile of mining, such as:
 SURFACE MINING | 193

• Excavator / loader that did the load;

• Operating Bank - wide and maneuvering square of the conditions can be found;
• Excavated and transported material - sterile or ore;
• What was the machine operator;
• What distance transported;
• Cycle time;
• What time of day (for constant day and night operations) loads happen more often?
• Payloads transportation by truck and it´s recurrence.

The information above is used to create monthly reports to show the evolution of operators,
common location of occurrences, common material, cycle time and frequency that each tire has
depreciated with badly centered loads. May thus infer how harmful the transport of these loads on tire
life is and create more precise management training for equipment instruction team.

Telemetry model for load suspensions pressures

Choose snippets are necessary to creation of the system Minecare trend using beacon’s own
Modular Mining. The so-called beacons (Figure 4) are points of reference in the graphic area of the
order containing the electronic map of the mine.

Figure 4: Mine road chosen for reading suspensions pressures and representation of the dispatch
system - beacons recognition and creation of telemetry rule.

These points are used by the system to locate the equipment and optimize it, providing the
next load of the truck. After defined the passages with their beacons in the dispatch system, move to
field evaluation and follow-generated graphics with the respective pressures suspensions. For this,
create the rules in Minecare system. See Figure 5 for an example of the rule created for the excerpts:

Figure 5: Trend rule model created in Minecare system - collecting pressure values of the suspensions.

Comparisons were made between the positions of the masses on the truck’s bucket to calibrate
the telemetry and refined classification rules of ROM loads to supply the crushing plants. The
194 | 24th WORLD MINING CONGRESS PROCEEDINGS

pressures of the suspensions are collected and analyzed by the trend, or telemetry rule when travelling
between the reading beacons.

Figure 6: Centralized ROM payload and pressures of the rear suspensions.

Figure 6 shows how the pressures in the rear suspension vary during operation around the
shaft. The variations are caused due to depressions in the mine roads. Figure 7 shows how the
decentralized payload interferes with the right pressures experienced by the suspension during the
truck route. This difference can be understood as a transfer not only to the suspensions, but also to tire
components and frame (chassis) of the equipment.

Figure 7: Decentralized load to the right.

 SURFACE MINING | 195

Likewise for load decentralized to the right, the answers of the suspensions are the same of it
shifted to the left, Figure 8. In both cases the effects on the equipment and the operator are the same,
varying only the path on sharp curves.

Figure 8: Decentralized load the left.

Table 1 is an example of the database created by collecting values of the suspensions. In the
field "event" (5th column) the classification of load positioning is validated through the interaction of
KPIs previously seen. Other information can be used for treatment of deviations, such as training needs
of loader operators as well as local excavators with more decentralized loads.

Table 1: Sample database created through the records

RESULTS

After the necessary adjustments in Minecare system for collection and storage of data, it began the
analysis of the evolution of alarm records generated on the operation. The total material data in the
three plants of Itabira complex between June to October 2015 is shown on table 2.

Table 2: Total mass delivered to the crushing plants Itabira Complex and percentage of
decentralized payloads. Source: Dispatch System and
Minecare

The access to the processing plants in the Itabira complex were monitored by the rules created in
the system for collecting and storing data from the pressures of suspensions of trucks from June to
196 | 24th WORLD MINING CONGRESS PROCEEDINGS

October. All transportation equipment to move these sections were monitored and their loads
classified.

In June was counted 385 decentralized loads of ROM transportation in Itabira. This represents
1.6% of total ore cargo for that month (24,692 loads delivered to the crushing plants). With the
progress of the action plan and the daily monitoring team-by-team, good results were achieved,
keeping the months of August and September at the percentage of 0.9 % of the total charges. Figure 10
show the evolution of the decentralized loads from June to October, 2015.

Figure 9: Evolution of occurrences of off-center loads.

In October there was interference on the mining with a hydraulic excavator, shovel type,
PC5500 Komatsu, see figure 10. Narrow areas difficult maneuvering of trucks and damage mining
productivity making it more complicated to center the loads. Confined spaces sometimes force shovel
operators to load it from the back, which raises operational risks. This situation must be avoided, but in
this particular case, it was necessary to carry out the mining to supply the hematite to the crushing
plants, one of the few offering fronts of such material available that month.

Figure 10: EM2970 the mining plan showing point of narrowing. Source: Mining Plan October 2015,
short-term planning Itabira, Vale

The result was reflected in a higher generation of decentralized loads, being represented on
figure 11.
 SURFACE MINING | 197

Figure 11: Evolution of decentralized load operation with the EM2970. Source: Dispatch System and
Minecare - Mine Operation Itabira.

As it is shown on Figure 11, the EM2970 shovel went through points of nips during mining in
Itabira Conceição mine in October and had a negative influence on the increase in instances of bad
centralized loads. A total of 138 charges representing almost 50 % of the total (277 loads).

CONCLUSION

Decentralized payloads act negatively on longevity of OTR tires and must be avoided in
mining operations. The directly affected operating parameters are pressure and temperature of these
components. Therefore, tires in operation with these values outside specifications suffer irreversible
damage, causing decrease in lifetime and increasing operating costs.

This study shows that it is possible create a database by collecting telemetry parameters,
therefore increase asset management and understand the possible causes of the occurrences. The
records of the occurrences contain valuable information for the operation as local of load, operators
who require recycling, time of the events, equipment involved and material transported. All these data
can be used for better management of training and control costs in the load and haul phases.

As June was the reference month, the initial of the effective control, a percentage of 1.6% of
ROM loads were classified as decentralized. Obtained the lowest levels in August and September, 0.9
% (a decrease of 43% compared to the month of June). In October with the interference (narrowing the
maneuvering area) in the mining of a hydraulic shovel excavator and consequently a rise in
registrations to 1.2% the total loads.

The continuity of the actions and commitment of everyone involved in the process are of
fundamental importance to maintain the levels below 1 % of the total ROM loads in Itabira Complex.
That will ensure the gain calculation in hours worked of tires and the savings generated by the
reduction of non-center loads.

Tire maintenance Manual (2008) – Good Year/Off the road Tires, 127 pp.
REFERENCES

Caterpillar (2013) Field Guide, 286 pp, mining.cat.com. Reference #AEXQ0030-03

CHAMANARA, ALI (2013). Enhancing mine haul truck KPIs via payload balance, Edmonton,
Alberta (Doctoral dissertation); 165 pp.
Maximising tire life - Otraco web publications – 18 pp; www.otraco.com
Michelin Guideline (2012) – Utilization and Maintenance, 177 pp, www.michelinearthmover.com
198 | 24th WORLD MINING CONGRESS PROCEEDINGS

PRACTICAL HAUL ROAD DESIGN

METHODOLOGY APPLICATION BASED
PRACTICAL HAUL ROAD DESIGN METHODOLOGY APPLICATION BASED ON SITE

ON SITE CHARACTERIZATION
CHARACTERIZATION
P. R. da Silveira, R. L. Peroni, A. T. Visser

*P.R. da Silveira1, R.L. Peroni2, A.T. Visser3

1
Pavimentadora e Construtora Falchetti Ltda

993 Norberto Brunatto Highway

Tubarão, Brazil

(*Corresponding author: [email protected])

2
Mining Engineering Department, Federal University of Rio Grande do Sul

9500 Bento Gonçalves Avenue – Building 75, Room 116

Porto Alegre, Brazil

3
Department of Civil Engineering, University of Pretoria

Pretoria, South Africa

October 18-21, 2016 • Rio de Janeiro /RJ • Brazil