Coating Defects Fitz Atlas

Download as pdf or txt
Download as pdf or txt
You are on page 1of 73

Application & Coating Defects

CONTENTS

ADHESION FAILURE
ALLIGATORING
ALUMINIUM CORROSION
BITTINESS
BLEACHING
BLEEDING
BLISTERING
BLOOM
BRIDGING
BRUSH MARKS
BUBBLES or BUBBLING
CHALKING
CHECKING
CHEESINESS
CISSING
COBWEBBING
CRACKING
CRATERING
CROWSFOOTING
DELAMINATION
DRYSPRAY
EFFLORESCENCE
EROSION
FADING
FILIFORM
FLAKING
FLOCCULATION
FLOODING
FLOTATION
GRINNING
GRIT INCLUSIONS
GROWTH
INCORRECT COATING SYSTEM
IMPACT DAMAGE
LAMINATIONS or SHELLING
MISSES/ SKIPS/ HOLIDAYS
MISSING TOPCOAT
MUD CRACKING
ORANGE PEEL
OVERSPRAY
PEELING
PINHOLES
RAIN DAMAGE-WATER
SPOTTING
RIPPLED COATING
ROT
RUNS or SAGS
RUST RASHING
RUST SPOTTING
RUST STAINING
SAPONIFICATION
SETTLEMENT
SOLVENT LIFTING
SOLVENT POPPING
TACKINESS
UNDERCUTTING
WATER SPOTTING
WRINKLING
ZINC CARBONATES
ADHESION FAILURE
see also delamination and flaking

Description: Paint fails to adhere to substrate or underlying coats of paint.


Probable Causes: Surface contamination or condensation.
Prevention: Ensure that the surface is clean, dry and free from any
contamination and that the surface has been suitably prepared.
Use the correct coating specification.
Repair: Depends upon the extent of adhesion failure. Removal of defective
areas will be necessary prior to adequate preparation and
application of correct coating system to manufacturer's
recommendations.

Other examples are shown on the following page


ADHESION FAILURE
see also delamination and flaking
ALLIGATORING
(also know as Crocodilimg)

Description: Very large (macro) checking or cracking which resembles the skin
of an alligator or crocodile. Cracks may penetrate through to the
undercoat down to the substrate.
Probable Causes: Internal stresses in the coating where the surface shrinks faster than
the body of the paint film. Can be caused by excessive film
thickness and limited paint flexibility. Also found on paint films
having a soft undercoat with a hard topcoat.
Prevention: Use correct coating specification and materials. Avoid excessive
thickness. Avoid application at high ambient temperatures.
Repair: Repair will depend upon size and extent of alligatoring. Abrade or
remove all affected coats and apply suitable undercoat and topcoat.
Follow recommended application procedures.
ALUMINIUM CORROSION

Description: Blistering of the paint coating due to aluminium corrosion product


under the paint.
Probable Causes: Pinholes in the coating. Porosity of flame sprayed aluminium.
Insufficient coating thickness.
Prevention: Use correctly formulated coating system applied in the correct
thickness.
Repair: Blast clean and recoat.
BITTINESS
(also know as Peppery, Seedy or Seediness)

Description: Film contaminated by particles of paint skin, gel, flocculated


material or foreign matter,which project above the surface of the
paint film to give a rough appearance. The term Peppery is used
when the bits are small and uniformly distributed.
Probable Causes: The main cause is contamination within or on the surface of the
paint film.This can be paint skin, gelled particles, airborne sand and
grit or contamination from brushes, rollers etc.
Prevention: Use clean application equipment and clean working environment.
Use new uncontaminated paint.Follow good painting practices.
Repair: Repair depends on size and extent of problem. Abrade or
completely remove the contaminated layer and recoat.
BLEACHING
(see also Fading)

Description: Total loss of colour of a coating.


Probable Causes: Bleaching due to weathering or chemical attack.
Prevention: Use colour stable pigments or a system which will withstand the
chemical environment.
Repair: Remove bleached coating or abrade and recoat using a more
suitable coating system.
BLEEDING
also called “Bleed Through”

Description: Staining of a paint film by diffusion of a soluble coloured substance


from the underlying paint to give undesirable discoloration or
staining .Very often/this is seen where bitumen or tar based
products are over-coated with alkyd based or other conventional
topcoats. Also occurs with emulsion paints.
Probable Causes: “Bleed Through” is generally a full or partial redissolving of the
previous coat. Bleeding can happen when strong solvents are used
in the topcoats.
Prevention: Use correct coating specification and materials. Use compatible
materials. Use appropriate sealer coat.
Repair: Remove stained or contaminated layer. Apply a suitable sealer coat
which will not dissolve soluble material e.g.an aluminium pigmented
coating.
BLISTERING

Description: Dome shaped projections or blisters in the dry paint film through
local loss of adhesion from the underlying surface. Blisters may
contain liquid, gas or crystals.
Probable Causes: Localised loss of adhesion caused by contamination with grease,
oil, salts, rust, trapped moisture, retained solvent, hydrogen vapour
pressure (on coatings used with cathodic protection), soluble
pigments etc. Osmotic blistering can also occur in immersed
conditions.
Prevention: Ensure correct surface preparation and application.
Apply a suitable coating system.
Repair: Depending upon size and type of blistering, remove blistered areas
or entire coating system and repair or fully recoat.

Other examples are shown on the following page


BLISTERING
BLOOM

Description: A hazy deposit on the surface of the paint film resembling the bloom
on grape, resulting in a loss of gloss and a dulling of colour.
Probable Causes: Paint film exposed to condensation or moisture during curing
(common phenomenon with amine cured epoxies). Incorrect solvent
blend can also contribute to blooming.
Prevention: Apply and cure coating systems under correct environmental
conditions and follow the manufacturer's recommendations.
Repair: Remove bloom with clean cloth or suitable solvent cleaners.
If necessary /apply undercoat/ topcoat following manufacturer's
recommendations.
BRIDGING

Description: The covering over of unfilled gaps such as cracks or corners with
a film of coating material.This causes a weakness in the paint film
which may crack, blister or flake off.
Probable Causes: Poor application. High viscosity paint system. Failure to brush paint
into corners and over welds.
Prevention: Brush apply a stripe coat into corners and welds/and fill all cracks
prior to application of the full coating system.
Repair: Remove all loose paint/abrade the surface/apply a stripe coat by
brush and recoat.
BRUSH MARKS
(also Ladering, Ladders or Ropiness)

Description: Undesirable ridges and furrows which remain in a dry paint film
after brush application / where the paint film has not flowed out.
May be found as a cross-hatch pattern (Laddering) where alternate
coats have been applied in opposite directions. Pronounced brush
marks are known as Ropiness.
Probable Causes: Viscosity of material may be too high for brush application /Incorrect
thinners used in the paint / Inadequate mixing or poor application
technique. Two-pack paints may have exceeded application pot-life.
Prevention: Use brushing grade of paint and apply adequate thickness.
Thin paint to brushing viscosity. Use within pot-life
Repair: Depending on extent of brush marks, thoroughly abrade surface and
recoat with a suitable viscosity paint.
BUBBLES OR BUBBLING

Description: Bubbles within a paint film appear as small raised blisters. These
may be intact or broken (to leave a crater). Can be found in
excessively thick paint films, especially if spray applied, and also
with roller application.This should not be confused with blistering.
Probable Causes: Trapped air/solvent within the coating which is not released before
the surface dries.Can be found with factory applied coatings where
application is by dipping, electrodeposition or roller coating.
Prevention: Spray application - use airless spray equipment, adjust viscosity
with thinners or modify spray temperature. Use correct mixing
equipment to ensure air is not stirred in during mixing.
Add defoaming agent to emulsion paints.
Repair: Depending on extent and severity of bubbling, abrade or remove
the offending coat(s) and recoat.
CHALKING

Description: A friable, powdery layer on the surface of a paint film. A change of


colour or fading is also seen.Chalking rates vary with pigment
concentration and choice ofbinder.Chalking is a known
characteristic of certain paints e.g.epoxy paints.
Probable Causes: Disintegration of the paint binder on exposure to weathering
and / or UV light.
Prevention: Apply a suitable topcoat with high resistance to chalking,
and UV resistance.
Repair: Remove all powdery deposits by abrasion or light sweep blast
cleaning, wipe loose material off and apply a chalk resistant topcoat.
CHECKING
(see also cracking)

Description: Fine cracks which do not penetrate the topcoat of a paint system.
Some checking can be so minute that it is impossible to see
without magnification.
Probable Causes: Typically a formulation and/or a specification problem.As with
cracking, stresses are developed which cause the surface of the
paint film to become brittle and crack. Limited paint flexibility.
Prevention: Use a correctly formulated coating system.
Repair: Abrade and clean surface then apply an undercoat/topcoat to suit.

Other examples are shown on the following page


CHECKING
(see also cracking)
CHEESINESS
(Soft Coating)

Description: Coating remains soft, even after prolonged drying time.


Probable Causes: Wrong mixing ratio for two-pack paints.Too low a drying/ curing
temperature. Excessive solvent retained within the coating.
Prevention: Ensure adequate mixing of two-pack paints.Only use the
recommended amount of thinners. Apply and cure the coating under
controlled environmental conditions.
Repair: Remove all soft coatings and apply suitable coating system or
topcoat to coating manufacturer's recommendations.
CISSING
(also referred to as Crawling and Fisheyes)

Description: Surface breaks in a wet paint film, where the paint has receded to
expose the underlying substrate. Sometimes known as crawling or
fisheyes.The paint is unable to wet-out the substrate. Can be very
large.
Probable Causes: Surface contamination by either moisture or foreign matter such as
oil, grease, silicone etc. Also known to happen when incorrect
solvent blends have been used.
Prevention: Ensure surface is clean and free from grease, oil and foreign
contaminates prior to application of coating.
Repair Abrade and thoroughly clean the contaminated surface or remove
the coating to achieve a clean surface. Reapply the coating system
to the coating manufacturer's recommendations.
COBWEBBING

Description: The production of fine filaments instead of normal atomised


particles when some solutions of high molecular weight polymers
are sprayed.
Probable Causes: Too high a viscosity with some types of polymer solutions.
Prevention: Reduce the spraying viscosity. Select a more suitable solvent
blend.Change the spraying conditions.
Repair: Abrade to remove all affected material and recoat.
CRACKING
(see also Alligatoring and Checking)

Description: Paint coatings with visible cracks which may penetrate down to the
substrate. Cracking comes in several forms, from minute cracking
to severe cracking.
Probable Causes: Cracking is generally a stress related failure and can be attributed to
surface movement, ageing, absorption and desorption of moisture
and general lack of flexibility of the coating. The thicker the paint
film the greater the possibility it will crack.
Prevention: Use correct coating systems, application techniques and dry film
thicknesses. Alternatively, use a more flexible coating system.
Repair: Abrade to remove all cracked paint. Correctly reapply the coating
system or use a more flexible system and one less prone to
cracking.

Other examples are shown on the following page


CRACKING
(see also Alligatoring and Checking)
CRATERING

Description: The formation of small bowl shaped depressions in the paint film.
Not to be confused with Cissing.
Probable Causes: Trapped air bubbles which have burst to leave small craters as the
coating dries.The coating has insufficient time to flow into a uniform
film.
Prevention: Improve spray technique to avoid air entrainment. Add thinners as
recommended by the paint supplier.
Repair: Abrade and clean the surface and recoat.
CROWSFOOTING
(see also Wrinkling)

Description: The development of small wrinkles in the paint film which occur in a
pattern resembling that of a crow's foot.
Probable Causes: Usually due to the surface drying rapidly to form a skin which then
wrinkles as solvent slowly evaporates from the soft underlying paint.
Prevention: Apply a thinner coat of paint/add slower drying thinners, check
application and drying conditions are correct for the paint system
used.
Repair: Abrade the surface when fully dry and recoat.
DELAMINATION
(see also Adhesion Faiture and Flaking)

Description: Loss of adhesion between coats of paint.


Probable Causes: Provided compatible paint materials have been used, delamination
defects are generally related to poor surface preparation and
application defects/such as contamination between coats; exceeding
overcoat times;application to a glossy surface.
Prevention: Ensure no contamination between paint coats, closely follow
intercoat times, lightly abrade and clean glossy surfaces between
coats.
Repair: Depending on extent, abrade and recoat or completely remove the
delaminated coating and reapply.
DELAMINATION
(see also Adhesion Faiture and Flaking)
DRY SPRAY
(see also Overspray)

Description: Rough and uneven finish to the surface of the paint film where the
particles are insufficiently fluid to flow together and are often poorly
adhered.
Probable Causes: Incorrect spray application i.e.gun distance.Also associated with fast
drying products and too high an application temperature.
Prevention: Use correct coating application equipment and techniques. Use a
slower drying solvent or solvent blend. Follow recommended
application procedures.
Repair: Abrade and remove any loose dryspray and re-apply coating or
topcoat.
EFFLORESCENCE

Description: White (powdery) substance on the substrate of concrete,


brick/masonry and plaster/The efflorescence.which comes from the
migration of salts, lifts the paint from the substrate.
Probable Causes: Soluble salts within the substrate. Moisture brings the salts to the
surface of the substrate resulting in coating adhesion failure.
Prevention: Ensure surface is moisture free, clean and suitable for application of
the coating system. Remove or eliminate the source of moisture.
Repair: Remove all powdery substances and thoroughly clean the surface.
Apply a suitable sealer and coating system formulated for concrete,
masonry etc.
EROSION

Description: Selective removal of paint films from areas or high spots.


Probable Causes: The wearing away of the paint film by various elements such as
rain, snow, wind, sand etc. Found to be more prominent on brush
applied coatings because of the uneven finish.
Prevention: Use a suitable coating system with resistance to surface
erosion/abrasion.
Repair: Clean surface free from contamination and apply a coating system
formulated and tested forthe specific environment.
FADING
(see also Bleaching)

Description: Discoloration or gradual decrease in colour of a paint when


exposed to sunlight/weather. May be accompanied by loss of gloss.
In some situations it may resemble chalking but without the
powdery surface. Fading tends to accelerate in the presence
moisture.
Probable Causes: Incorrect pigmentation; use of organic pigments; atmospheric
contamination; porous substrate.
Prevention: Use correct coating systems which resists UV light and fading.
Use a coating with light stable pigments.
Repair: Abrade and clean the surface and apply a light stable coating
system.
FILIFORM
(Corrosion)

Description: Random threads of corrosion that develop beneath thin lacquers


and other coating films from a growing head or point. Often seen on
old ”tin” food cans/with thin electro plating but also seen on painted
aluminium and other surfaces.
Probable Causes: Contamination on the metallic substrate or damage to the coating
which allows a corrosion cell to develop at the tip and advance
under the coating.
Prevention: Ensure no contamination exists on the substrate prior to coating
application.
Repair: Remove all traces of corrosion products and non adhering coatings.
Abrade, clean and coat to manufacturer's recommendations.
FLAKING
(see also Delamination and Adhesion Faiture)

Description: A form of adhesion failure where paint literally flakes from the
substrate. A familiar sight on wood substrates and on galvanising.
Probable Causes: Incorrect paint system used. Either none or incorrect pre-treatment
used for certain substrate i.e. non-ferrous or galvanised. Also poor
application techniques. May also be attributed to differential
expansion and contraction of paint and substrate e.g.wood.
Can be the result of ageing of the paint system.
Prevention: Use correct coating system and pre-treatment.
Repair: Remove all flaking coating until a firm edge can be achieved.
Abrade, sweep blast and clean overall and apply suitable coating
system to coating manufacturer's recommendations.
FLAKING
(see also Delamination and Adhesion Faiture)
FLOCCULATION

Description: The development of loosely coherent pigment agglomerates in a


coating material.
Probable Causes: Non-uniform pigment dispersion which results in the pigments
forming agglomerations. Unsuitablethinners or inadequate mixing.
Prevention: Ensure only properly formulated and mixed products are used.
Use recommended thinners.
Repair: Remove coating where flocculation is visible. Abrade and clean the
surface and apply a properly formulated and mixed coating system.
FLOODING
(see also Flotation)

Description: A defect which appears soon after application due to pigment


separation. The visual appearance is a deepening of the colour.
The affected area dries to a deeper shade than the remainder of the
surface.
Probable Causes: Pigment separation and settlement.
Prevention: Use correctly formulated products.
Repair: Lightly abrade and clean and then recoat with a suitably formulated
material.
FLOTATION
(see also Flooding)

Description: Occurs in coloured materials containing mixtures of different


pigments. lt closely resembles flooding/although a mottled or
streaky effect is produced when the different pigments separate.
Probable Causes: The mottled effect, which is visible to the eye, is caused by
separation of the different coloured pigments. It may also result
from the addition of excessive thinners.
Prevention: Use correctly formulated products. Do not over thin with solvent.
Repair: Abrade and clean overall and apply a suitable sealer or topcoat.
GRINNING
or “Grinning Through”

Description: The underlying surface is visible through the paint film due to
inadequate hiding power of the coating material. This is sometimes
called 'Grinning-Through'. Often seen where dark colours are
overcoated with lighter colours.
Probable Causes: Low film thickness of penultimate coat. Poor opacity and covering
power of topcoat coat. Strong colour of primer/ undercoats.
Prevention: Apply adequate dry film thickness between individual coats. Use
opaque coatings with good covering properties.
Repair: Apply additional compatible coats to clean surface.
GRIT INCLUSIONS

Description: Particles of grit and dust embedded within the coating system.
Probable Causes: Failure to remove used grit from the surface prior to application of
the paint. Contamination of the wet primer or undercoat with grit
from other blast cleaning operations. Wind blown grit particles
adhering to the topcoat.
Prevention: Ensure all used grit is removed before application of fresh paint.
Do not carry our blast cleaning whilst there is wet paint on nearby
surfaces. Ensure than all cans of paint and brushes etc. are
protected during blast cleaning operations.
Repair: Abrade or blast clean the surface to remove all grit contamination,
thoroughly clean the surface and recoat.
GROWTH
(on the surface of paint film)

Description: Growth and attachments of natural and organisms to surface of


finished products.These vary in form/size and lifespan, e.g. algae,
mosses etc.
Probable Causes: Generally, natural organisms within moist, wet or immersed
conditions. Growth may continue after attachment.
Prevention: Use correct coating specification and products suitable for the
environment. Where practical, clean regularly to prevent build-up of
moss and algae.
Repair: Clean and remove all growth.abrade the surface and apply a
suitable coating system.
INCORECT COATING SYSTEM

Description: An unsuitable or incompatible coating system has been used which


results in rapid failure.
Probable Causes: Use of incompatible or unsuitable coating materials.
Prevention: Use correct coating specification and materials. Ensure that
different coats are compatible with each other.
Repair: Remove all defective coating and apply correct coating system to
manufacturer's recommendations.
INCORECT COATING SYSTEM
IMPACT DEMAGE
(Star cracking)

Description: Cracks which radiate from a point of impact.


Probable Causes: Impact damage to a relatively brittle coating.
Often see on glass fibre reinforced plastics.
Prevention: Prevent impact damage.
Repair: Abrade all damaged areas and recoat.
IMPACT DEMAGE
(Star cracking)
LAMINATIONS OR SHELLING
(of cast iron)

Description: The photograph shows flaking or shelling of sections of cast iron


from the surface which have been overpainted and which have led
to subsequent rust staining.
Probable Causes: Failure to remove or treat delaminated sections prior to application
of the coating system.
Prevention: Ensure proper surface preparation is carried out.
Repair: Grind all laminations to remove them, blast clean the surface and
recoat.
MISSES / SKIPS / HOLIDAYS

Description: Exposed areas of substrate when the intention was to coat the
entire area. Could be confined to a single coat in a multi-coat paint
system.
Probable Causes: Poor application techniques. Lack of quality control.
Prevention: Use correct application techniques. Apply good painting practices.
Use qualified inspectors.
Repair: Apply coatings to suitable prepared and cleaned substrates to
original specification and manufacturer's repair procedures.
MISSING TOPCOAT

Description: Failure to apply the topcoat leaving the undercoat exposed.


Probable Causes: Poor coating application and quality control. Inadequate dry film
thickness.
Prevention: Thoroughly inspect all surfaces to ensure each coat has been
correctly applied.
Repair: Abrade the surface and either apply the topcoat, or an additional
undercoat and topco at accordance with the paint suppliers
recommendations.
MUD CRACKING

Description: The dried paint film has the appearance of a dried-out mud bath.
Cracks vary in size and amount but form a network of cracks.
Probable Causes: Generally over application of heavily pigmented primers such as
inorganic zinc silicates or water based coatings, although can occur
with other over thick systems.
Prevention: Only apply the recommended coating thickness. Use recommended
application techniques with suitably formulated products.
Repair: Remove all cracked and flaking paint back to a sound base.
Abrade and clean surface. Re-apply coating to manufacturer's
recommendations.
ORANGE PEEL
(also known as Pock-marking)

Description: The uniform pock-marked appearance, in particular of a sprayed


paint film in which the surface of the paint film resembles the skin of
an orange.
Probable Causes: Failure of the paint film to flow out. Usually caused by poor
application techniques or by incorrect solvent blend.
Prevention: Use correct application techniques with suitably formulated products.
Repair: Where aesthetics are of concern/abrade overall,clean and recoat.
OVERSPRAY
(see also Dryspray)

Description: Small particles of paint adhering to the surface of the previous dry
coat, generally adjacent to the area being sprayed. Often appears
as a pebbly surface. Similar to dry spray.
Probable Causes: Particles of wet paint falling outside the spray pattern. Solvent
evaporates too rapidly. Spray application under windy conditions.
Prevention: Spray paint under suitable environmental conditions. Adjust spray
pattern to minimise overspray onto dry paint.
Repair: Before cure or drying: remove by dry brushing followed by solvent
wipe. After cure: abrade and apply another coat.
PEELING
(see also Flaking)

Description: Similar to flaking/although peeling tends to produce soft and pliable


coatings which can be pulled away from or spontaneously flake
away from the substrate or from between coats, due to loss of
adhesion.
Probable Causes: Peeling is the reduction in bond strength of the paint film due to
contamination or incompatibility of coats.
Prevention: Use correct coating system and specification applied to clean and
uncontaminated surfaces.
Repair: Remove all soft and pliable coating back to a firm edge or total
removal. Abrade, clean and apply suitable coating system to coating
manufacturer's recommendations.
PINHOLES

Description: The formation of minute holes in the wet paint film during application
and drying, due to air or gas bubbles which burst, giving rise to small
craters or holes which fail to coalesce before the film dries.
Probable Causes: Solvent or air entrapment within a paint film. A common problem
when coating porous substrate such as zinc filled primers, zinc
silicates and metal sprayed coatings etc. Pinholes can also be
caused by incorrect spray application or incorrect solvent blend.
Prevention: Use correct application techniques with suitably formulated products.
Correct solvent blends and environmental conditions. Check spray
equipment and distance of spray gun from the surface.
Repair: Abrade, clean overall and apply suitable tiecoat/undercoat and
topcoat as necessary.

Another example is shown on the following page


PINHOLES
RAIN DAMAGE – WATER SPOTTING

Description: Craters and water marks on the surface of the paint film caused by
rain or heavy condensation.
Probable Causes: Rain falling on a freshly painted surface causes craters to form on
the surface before it has hardened sufficiently.
Prevention: Allow coating (where practicable) to surface harden prior to
exposure to rain or heavy condensation.
Repair: Abrade,clean all surface damage areas and apply overall
undercoat / topcoat.
RIPPELED COATING

Description: A rippled effect on the surface of the paint.


Probable Causes: Strong wind blowing across the surface of wet paint causes it to
ripple.Where this is on the underside,the ripples can hang down in
the form of small stalactites. Can also be caused by poor
application techniques.
Prevention: Do not apply paint under unfavourable conditions. Use correct
application equipment and workmanship.
Repair: When mild ripples are seen/abrade the surface and recoat. Where
this is a major effect, remove the coatings and recoat.
ROT
(wood)

Description: Damp and rotten wood exposing friable substance, splitting,flaking


and cracking of paint.
Probable Causes: Generally poor maintenance or application over soft and rotten
wood. Occasionally, use of incorrect paint system.
Prevention: Correct and ongoing maintenance to the wood and coating. Ensure
all wooden surfaces are sound and free from rot before application
of paint.
Repair: Replace rotten wood, preferably with treated wood.Apply a suitable
coating system formulated for wood surfaces.
RUNS OR SAGS
(also described as curtains or wrinklers)

Description: Downward movement and tears of paint which appear soon after
application to vertical surfaces due to excessive paint application. In
severe situations it may be described as curtains.
Probable Causes: Over application of paint/excessive thinners/wrong (lack) of curing
agent or just poor workmanship. Could, in extreme circumstances,
be a formulation problem.
Prevention: Use correct application techniques with suitably formulated
products.
Repair: While the paint is still wet.brush out runs and sags.When the paint
has dried, abrade and clean defective areas and apply overall coat
or spot repair, as necessary.
RUNS OR SAGS
(also described as curtains or wrinklers)
RUST RASHING
to Thermal Spray Coating

Description: Spots of ferrous oxide develop within the pores of a sprayed metal
coating. Similar to rust spotting of a paint
Probable Causes: A phenomenon which can develop on aluminium thermal sprayed
coatings soon after application. Moisture is absorbed into the metal
coating and reacts with the ferrous substrate. Early sealing with an
appropriate coating prevents such events.
Prevention: Apply thermal spray coating in a controlled environment. Seal metal
sprayed surface immediately after application.
Repair: Clean rust rashing locations,wire brush/fresh water clean. Providing
dry film thickness of the thermal spray is adequate, apply sealer coat
to coating manufacturer's recommendations.
RUST SPOTTING
also referred to as rash rusting

Description: Fine spots of rust which appear on a paint film, usually a thin primer
coat.This frequently starts as localised spotting but rapidly spreads
over the surface.
Probable Causes: Low film thickness, voids and holidays,also defects in the steel
i.e.laminations. Too high a surface profile may cause penetration of
peaks through a paint film and cause rust spotting. May also occur
from metallic contamination of a coated surface by grinding dust
etc.
Prevention: Apply an adequate primer coat. Ensure coating system adequately
covers the surface profile. Use a thicker coating system or a lower
blast profile.
Protect coating from contamination with grinding dust etc.
Repair: Depending on type and extent, abrade or blast clean surface and
recoat. Remove all foreign debris and abrade, clean damaged
areas. Apply spot repair or recoat overall.
RUST SPOTTING
also referred to as rash rusting
RUST STAINING

Description: A light staining on the surface of the paint caused by the


precipitation of ferrous oxide.
Probable Causes: Water run-off from a rusty surface above a soundly coated surface.
Rust staining occurs when the rust is wetted-out and contaminated
water runs over and discolours other items or locations. Usually
more of an eye-sore than a defect. The coating itself may not be
defective/only stained.
Prevention: Adequate design and suitable maintenance.
Repair: Remove staining and apply a cosmetic coating, as necessary.
SAPONIFICATION

Description: The coating appears to be soft and sticky. Can be sporadic isolated
spots or an overall effect.
Probable Causes: A soap formation reaction between esters/alkali and water. Often
found in alkyd and oil coatings. Notably found on concrete coated
structures and coating used in conjunction with cathodic protection.
Prevention: Use correct coating specifications and materials.
Repair: Remove all soft coatings where saponification has occurred,
abrade, clean and re-apply undercoat/topcoat (non-saponifiable).
SETTLEMENT

Description: A term used to describe the settled pigment/solids in a liquid prior to


application. Found during paint storage. Settlement which occurs
after mixing and during application can result in different colours in
different areas.
Probable Causes: Old stock, heavily pigmented paint/wrong formulation or
contamination ofproduct. Can be a problem with zinc rich primers.
Prevention: Use products within shelf life. Use adequate mixing procedures.
Keep paint mixed or recirculated during spray application.
Repair: As Prevention:Where the results is a patchy finish, remove the
affected coating and recoat taking precautions against settlement.
SOLVENT LIFTING
see also Wrinkling

Description: Eruption of the surface of the paint film. Wrinkling and blistering
which leads to a weak surface and ultimate coating breakdown.
Probable Causes: Incompatible paint systems used. Topcoats with a strong solvent
blend can attack previous and weaker solvent blended coatings.
Overcoating before the previous coat has adequately hardened.
Prevention: Use correct coating specification, overcoating times and materials.
Conduct compatibility trials with undercoat/ topcoats.
Repair: Remove all defective coatings. Abrade, clean and recoat with correct
coating system,following the recommended overcoating times.
SOLVENT POPPING

Description: Solvent (clear) bubbles on the surface of the paint film soon after
application.
Probable Causes: Incorrect solvent blends, porous surfaces and wrong environmental
conditions.
Prevention: Use correct coating specifications and materials. Correct application
techniques and environmental conditions.
Repair: Lightly abrade and clean the surface and apply undercoat/ topcoat.
TACKINESS

No photograph available

Description: Soft film of applied coatings. Although beyond the wet and liquid
stage/the paint film remains as a tacky and soft surface. Sometimes
only apparent on touching the substrate.
Probable Causes: There are various reasons why a paint will remain tacky :
Over thickness;
Excessive thinners;
Wrong (lack of) curing agent;
Low drying / curing temperature;
Use of coating beyond pot life or shelf life.
Prevention: Use correct coating specifications and materials. Ensure two-pack
materials are correctly mixed. Follow paint suppliers
recommendations.
Repair: Remove defective coating. Abrade, clean and recoat.
UNDERCUTING

Description: Visual corrosion beneath a paint film. Corrosion travels beneath the
paint film and lifts the paint from the substrate. Severe cases can
show as blistering, flaking, cracks and exposed rust.
Probable Causes: Application of paint to corroded substrate. Rust creep from areas of
mechanical damage and missing primer coat. Can be found in
areas of poor design or access where inadequate preparation and
coating thickness was applied. Could also be due to lack of
maintenance.
Prevention: Use adequate coating specifications and maintenance procedures.
Apply a suitably formulated primer.
Repair: Spot repair localised areas. Clean areas back to sound base, apply
suitable repair coating to manufacturer's recommendations.
WATER SPOTTING
see also Rain spotting

Description: The spotty appearance of the paint film caused by drops of water on
the surface and which remains after the water has evaporated.
The effect may or may not be permanent.
Probable Causes: Rain drops falling on the wet paint film. These leave permanent
marks. Rain drops falling on a freshly dried but hard surface. When
the water evaporated, marks may be seen which can be rubbed off.
Prevention: Do not apply paint when rain is threatened.
Repair: Where the marks are just on the surface these may be washed off
but where there is cratering or permanent damage to the paint film,
abrade the surface and recoat.
WRINKLING
also Rivelling (see also Crow’s footing)

Description: The development of wrinkles in the paint film during


drying / wrinkling / swelling and blistering of the coating.
Probable Causes: Usually due to the initial formation of a surface skin with solvent
based paints. Also swelling of the coating from solvent attack.
Can arise from overcoating before the previous coat has adequately
hardened.
Prevention: Use correct coating specification and materials. Adequate mixing,
application and curing of materials. Follow the paint suppliers
recommended overcoating times.
Repair: Remove defective coatings. Abrade, clean and recoat.

Other examples are shown on the following page


WRINKLING
also Rivelling (see also Crow’s footing)
ZINC CARBONATES

Description: Loss of adhesion to galvanised surfaces. Blistering of paint on a


galvanised surface.
Probable Causes: White rust or carbonates on the surface of galvanising prior to
application ofthe paint coating. Corrosion of zinc under the paint
surface.Can be similar to rash rusting but white in colour.
Prevention: Seal zinc coating from the environment and application of an
appropriate protective coating system.
Repair: Water wash the surface to remove all traces of zinc corrosion
products. Sweep blast or abrade, clean and apply a suitable coating
system.

You might also like