RRU
RRU
RRU
Specifications
Contents
4.1.1.6.4.46 RRU3959/RRU3959w Technical Specifications
RF Specifications
Table 3 lists the RF specifications of an RRU3959/RRU3959w.
NOTE:
ATBR in the Transmit and Receive Channels column indicates that this RF module has A transmit channels
and B receive channels.
CxD W in the Output Power column indicates that this RF module is configured with C transmit channels and
the maximum output power of each transmit channel is D W.
EF MSR indicates that E and F data is carried on the same transmit channel of an RF module.
EF non-MSR indicates that E and F data is carried on two different transmit channels of an RF module.
GSM receiver sensitivity is measured, as recommended in 3GPP TS 51.021, at the antenna connector on
condition that the channel rate reaches 13 kbit/s and the bit error rate (BER) is not higher than 2%.
UMTS receiver sensitivity is measured, as recommended in 3GPP TS 25.104, over the full band at the antenna
connector on condition that the channel rate reaches 12.2 kbit/s and the BER is not higher than 0.001.
LTE FDD receiver sensitivity is measured, as recommended in 3GPP TS 36.104, under a 5 MHz channel
bandwidth based on the FRC A1-3 in Annex A.1 (QPSK, R = 1/3, 25 RBs) standard.
The RRU3959/RRU3959w that works in GSM mode and operates in the 900 MHz or 1800 MHz frequency band
complies with the EN 301 502 V9.2.1 standard.
The RRU3959/RRU3959w that works in UMTS, LTE FDD, or multi-standard radio (MSR) mode and operates
in the 900 or 1800 MHz frequency band complies with the ETSI EN 301 908 V5.2.1 and 3GPP TS 37.104
standards.
The RRU3959 that works in UMTS, LTE FDD, or MSR mode and operates in the 2100 MHz frequency band
complies with the 3GPP TS 37.104 standard.
RRU3959 2T2R GSM: 8 TRXs GSM: - GSM: - GSM: - The RRU3959 See the
(900MHz) UMTS: 113.7 116.5 119.2 (900 MHz) RRU3959
UMTS: UMTS: (theoreti supports a sheet in
Without 3900 Series
-125.8 -128.6 cal maximum
MIMO: 6 value) power Base
carriers configuration of
Station
UMTS: Power
With 2x60 W. For
-131.3 Consumptio
MIMO: 4 typical power n
carriers configurations, Specificatio
see Typical ns.
Power
Configuration for
RRU3959/RRU39
59w.
Engineering Specifications
The following table lists the equipment specifications of an RRU3959/RRU3959w.
RRU3959/RRU3959w -48 V DC; voltage range: 400 mm x 300 mm x 100 RRU3959 (900
-36 V DC to -57 V DC mm (without the MHz/1800
housing) MHz)/RRU3959w:
NOTE: 14 (without the
The RRU3959/RRU3959w housing)
supports AC power supply
RRU3959 (2100
when connected to an
external AC/DC power
MHz): 15 (without
module or an OPM15M. the housing)
For details, see AC/DC
Table 4 Equipment specifications of an RRU3959/RRU3959w
NOTE:
According to the
installation
scenario, traffic
load, and carrier
configuration, the
output power of
some RRUs may
temporarily
decrease when they
work in the highest
10°C temperature
range. For example,
if the highest
operating
temperature allowed
for an RRU is 50°C,
the actual operating
temperature cannot
exceed 40°C.
Otherwise, the
output power of the
RRU may
temporarily
decrease.
The following table lists the compliance standards for an RRU3959/RRU3959w.
Item Standard
RF 3GPP TS 45.005
3GPP TS 25.141
3GPP TS 36.141
3GPP TS 37.141
NOTE:
The validity period is one year.
The product can function properly within the validity period if the
storage environment meets the preceding standards.
When the
LBBPd2 or
UBBPd4 is
configured:
40
When the
LBBPd3,
UBBPd5,
or
UBBPd6 is
configured
40 if
the cell
number
is less
than or
equal to
3
20 if
the cell
number
is
greater
than or
equal to
4
Antenna Capability
The following table lists the antenna capability of an RRU3959/RRU3959w.
NOTE:
For RF modules supporting RET antennas, the feeding voltage is 12 V and feeding current is 2.3 A.