Scribd
Upload
242 views

Lab Report

The document describes a lab experiment to determine the specific heat of different metals using a calorimeter. Key steps include: 1) Assembling a "coffee cup" calorimeter and measuring the mass of water added. 2) Heating samples of aluminum, copper, iron and lead to 100°C then placing them in the water to observe temperature changes over 5 minutes. 3) Using the temperature changes of the water and metals, and specific heat of water, calculations are done to determine the specific heat of each metal.

Uploaded by

Lindsey Alexander
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
242 views

Lab Report

The document describes a lab experiment to determine the specific heat of different metals using a calorimeter. Key steps include: 1) Assembling a "coffee cup" calorimeter and measuring the mass of water added. 2) Heating samples of aluminum, copper, iron and lead to 100°C then placing them in the water to observe temperature changes over 5 minutes. 3) Using the temperature changes of the water and metals, and specific heat of water, calculations are done to determine the specific heat of each metal.

Uploaded by

Lindsey Alexander
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

Lab report

Introduction: Specific heat is an intensive property of a single-phase (solid, liquid or gas)


sample that describes how the temperature of the sample changes as it either absorbs or
loses heat energy. Specific heat is generally a function of temperature, but, to a good
approximation, it can be treated as being constant for a single phase over a moderate
temperature range. This set of experiments will focus all attention upon one particular area
of thermodynamics, namely calorimetry, a technique used to measure heat flow into and out
of matter. The basic idea of the technique is quite simple. The matter we are interested in
studying is placed into a container called a calorimeter that segregates the thermal process
we are interested in studying from the rest of the universe. As changes occur to that matter,
we can follow the movement of heat from one portion of the matter to another by
observing temperature changes. Equipment And Materials:Polystyrene calorimeter Glass
stirring rodThermometer Rubber bandPolystyrene coverPolystyrene
cupsWaterBeakersGraduated cylinderHot plates Test
tubesNaOHHClTimerExperimental Procedure:Determination of the Calorimeter
Constant:1.The calorimeter was assembled as depicted in figure 1 while making sure the
thermometer didn’t touch the bottom surface.

2.

Materials:

Two polystyrene coffee cups  Lid for polystyrene cup  Thermometer  250 mL beaker  400 mL
beaker  Ring stand  Two buret clamps  Hot plate  Four test tubes  Test-tube holder  50 mL
graduated cylinder  Water  aluminum, copper, iron, and lead powder  analytical balance

Hypothesis: the metal will get hotter.

3. Purpose: Explore how the specific heat of a substance can be determined using a “coffee cup”
calorimeter.

4. Question: How can you determine the specific heat of a metal using a calorimeter?

Procedure:

Step 2: Assemble a “Coffee Cup” Calorimeter a) Place one coffee cup inside the other. Then, put them
inside a 250 mL beaker. b) Cut a small hole in the center of the lid to hold the thermometer. Place the lid
on the top cup. Step 3: Measure the Masses of the Metals Repeat steps (a) through (c) below for each
of the four metals: aluminum, copper, iron, and lead. a) Add a piece of weigh paper to the balance. Tare
the balance. b) Measure approximately 12 g of aluminum onto the weigh paper. Record the mass to the
nearest 0.01 g. c) Place the metal in a test tube, and label the test tube with the metal’s name. Step 4:
Heat the Metals to 100°C in a Hot Water Bath a) Using a hot plate, heat approximately 200 mL of water
in a 400 mL beaker until boiling. b) Place the four test tubes of metal into the boiling water bath. Wait 5
minutes. Repeat steps 5 through 7 below for all four metals: aluminum, copper, iron, and lead. Before
repeating, raise the thermometer and remove the coffee cups and lid. Discard the water down the drain
and the metal according to your teacher’s directions. Clean and dry the calorimeter. Step 5: Measure the
Mass of the Water a) Tare the balance. Put calorimeter (no lid) on the balance. Measure the mass to the
nearest 0.01 g. Record in the data table. b) Use a graduated cylinder to add approximately 40 mL of
water to the calorimeter. Measure the mass of the calorimeter (no lid) and water to the nearest 0.01g.
Record in the data table. c) Subtract to find the mass of the water. Record in the data table. Step 6:
Reassemble the Calorimeter and Position the Thermometer a) Place the lid on the upper coffee cup, and
place the calorimeter into a 250 mL beaker in order to prevent the calorimeter from wobbling. b) Place
the thermometer on a buret holder on a ring stand, and lower the thermometer into the hole in the lid
until it makes contact with the liquid. c) Swirl the thermometer slightly, and confirm that the
thermometer is not touching the bottom of the cup. Step 7: Put the Metal in the Water, and Measure
Temperature Changes a) Measure the initial temperature of the water to the nearest 0.1°C. Record in
the data table. b) Raise the thermometer and lid slightly, and add the metal to the calorimeter. c)
Observe the increase in temperature every 60 seconds for 300 seconds. d) The temperature at 300
seconds (5 minutes) is the final temperature of both the metal and the water. Record it to the nearest
0.1°C in the data table. e) Subtract to find the temperature changes for the water and the metal.
(Remember that the metal was initially 100°C.) Record both values in the data table. Step 8: Compute
the Specific Heats of Each Metal Use your data, the equation below, and the specific heat of water
(4.184 J/g°C) to compute the specific heat values of each metal. Use a calculator, and round to the
nearest hundredth place.

Aluminum Copper Iron Lead mmetal, Mass of metal (g) Mass of calorimeter (no lid) (g) Mass of
calorimeter (no lid) + water (g) mwater, Mass of water (g) (Subtract masses above.) Initial temperature
of metal (°C) 100.0 100.0 100.0 100.0 Initial temperature of water (°C) Final temperature of both (°C)
∆Twater (°C) (Final – Initial) ∆Tmetal (°C) (Final – Initial) Specific heat of metal, cmetal Cost of metal
$1.00/pound $5.00/pound $0.10/pound $1.00/pound Safety risk Slight: corrodes easily when exposed to
acidic foods Slight: toxic at high concentration; can leach from pans None: source of beneficial dietary
iron Significant: toxic when ingested; can leach from pans Density of metal (g/cm3 ) 2.70 8.92 7.87 11.3

Conclusion: the metal did get hotter.

You might also like