SC10E016A
SC10E016A
SC10E016A
,
504 505 Deron Heights,
Baner Road, Pune 411 045, India
Phone : +91-20-65001587, 9764027070, 8390069393 Connecting. Converting. Leading !
email : info@santelequip.com .
16 Port Serial Device Server, Model SC10E16A
HIGHLIGHTS
• 8/16-port Ethernet Serial server with RISC 32bits 266MHz
CPU
• Standard 19-inch rack-mount 1U metal housing
• Each port can be independently configured
• Software selectable RS-232/422/485 for each port or Isolated
RS485/422 ports
• Dual 10/100Mbps Ethernet for networking redundancy
• Support TCP Server/Client UDP and Virtual Com multi-link mode
• Configuration via Serial Console, Telnet, Web Server or Windows-based utilities
• Relay out indicator for Network link-status
• LCM indication with 4 key pad setting
The Multi-port Industrial Serial Server SC10E16 is a gateway between Ethernet (TCP/IP) and RS232/422/485
communications. It allows almost any serial device to a LAN network.
By encapsulating serial data and transporting it over Ethernet, SC10E16 offers full-duplex, bi-directional data
transmission transparent between Serial port and Ethernet network.
Flexible configuration options enable this unit to be setup by Telnet, Web browser, Serial Console, or other
Windows utilities. Packed in a rugged metal housing with 19-inch rack mount and 100~240VAC wide power input
range, SC10E16 is ideal for almost any industrial and manufacturing automation.
With its powerful computing power and Linux platform, it could be a high performance controller for time-critical,
high-security, multi-function controller such as SCADA, tele communication, transportation, banking, hospital, etc.
TECHNICAL SPECIFICATIONS
System
CPU : 32-bit 266MHz RISC Processor with MMU
Flash : 2+ 8MB (2MB for Boot loader)
RAM : 32 Mbytes DDR
EEPROM : 8K Bytes
Watchdog : Hardware built-in
Ethernet
Compliance : IEEE802.3
Ports : 2-port
Transmission Rate : 10/100Mbps Auto-detection
Connector : RJ45
Auto MDI/MDI-X : No
Isolation : 1.5KV Magnetic Isolation
MAC chips : 2 Separate MAC chips
Mode : Redundancy mode & Dual Sub net mode
Dual Subnet Mode : Subnet is a logically visible subdivision of an IP network. The LAN 1 and LAN2 can be
assigned to different subnets. This feature gives the user flexible network manageability. Separate IP’s. Different
Class
Redundancy Mode
A goal of redundant topologies is to eliminate network downtime caused by a single point of failure. The LAN1 and
LAN2 can be assigned to the same IP network. It will enable the network to recover rapidly from failure and fault,
so that the failures and faults will be bypassed.
Software
Configuration : Web Page / Telnet / Serial console / Windows utility / LCM
Virtual Com : Windows & Linux port redirection software
Support Protocol : ARP, ICMP, TCP/IP, UDP, DHCP client, NTP, DNS, SNMP, SMTP, HTTP, Telnet
Serial
Interface : RS-232/422/485 software selectable
Ports : 8 / 16-port
Baud Rate : 110bps~921Kbps
Parity : None, Odd, Even, Mark, Space
Data Bits : 5, 6, 7, 8
Stop Bits : 1, 2
Flow Control : None, Software: Xon/Xoff, Hardware: RTS/CTS
Connector : RJ45
Isolation : 2.5 KV : In RS485/422 model only.
Protection
ESD : +/- 8 KV, +/- 15 KV
EFT/Burst : Power line : AC : 4 KV, DC : 2 KV, Data lines : 2 KV
Surge Protection : Signal Port : 2KV ( L to E ), Power Line DC 1 KV ( L to L & L to E ), Power Line AC : 4
KV L/N to E & 2 KV L to N
Power
Input : AC 100 ~ 260V, 24V DC & 48V DC options are also available
Consumption : Max. 8.5W
Reverse Polarity Protection : Yes. For DC Version
Environment
Operating Temp : 0°C to 60°C
Storage Temp : -40º to 85ºC
Relative Humidity : 5 to 95% rh non condensing
Heat Load : 34.12 BTU/hr
Dimension / Weight
WxHxD : 436mm x 43.5mm x 200mm
Weight : 3.2 Kg
San Telequip (P) Ltd.,
504 505 Deron Heights,
Baner Road, Pune 411 045, India
Phone : +91-20-65001587, 9764027070, 8390069393 Connecting. Converting. Leading !
email : info@santelequip.com .
APPROVALS : (The hardware is designed for & complies to the below approvals.)
EMISSION TESTS IMMUNITY TESTS
EN 55022:2006 Class A EN 55024:1998+a1:2001+A2:2003
AS/NZS CISPR 22:2006. Class A IEC 61000-4-2:2001 ED.1.2 ESD : Class A
EN 61000-3-2:2006, Class A IEC 61000-4-3:2006 ED.3.0 Radiated Freq : Class A
EN 61000-3-3:1995+A1:2001+A2:2005 IEC 61000-4-4:2004 ED.2.0 EFT / Burst : Class B
IEC 61000-4-5:2005 ED.2.0 Surge : Class A
IEC 61000-4-6:2006 ED.2.2 Conducted Disturbance : Class A
IEC 61000-4-8:2001 ED.1.1 Power Frequency : Class A
IEC 61000-4-11:2004 ED.2.0 Voltage Dips/Interruption : Class A & C
FCC Part 15: 2007, Subpart B, Class A (section 15.31, 15.107, and 15.109)
ICES-003: 2004, Class A (section 4&5)
ANSI C63.4-2003 (section 7 & 8)