EEE / INSTR F244
Microelectronic
Circuits
BITS Pilani
Pilani Campus
BITS Pilani
Pilani Campus
Amplifier Basics
Mixed signal System design
BITS Pilani, Deemed to be University under Section 3 of UGC Act, 1956
ADC- SubSystem Design
A to D Converter, D to A Converter
BITS Pilani, Deemed to be University under Section 3 of UGC Act, 1956
Flash ADC-100 Msps
BITS Pilani, Deemed to be University under Section 3 of UGC Act, 1956
Band width requirement of
OPAMP
Bits, pilani
BITS Pilani, Deemed to be University under Section 3 of UGC Act, 1956
Bits, pilani
DAC
BITS Pilani, Deemed to be University under Section 3 of UGC Act, 1956
Design issues
Diff amp, biasing circuit, CSA, C (if compensation is reqd.)
BITS Pilani, Deemed to be University under Section 3 of UGC Act, 1956
Concepts
• Signal amplification
• Voltage/ power gain/ Power efficiency
• Gain in decibels
• Voltage transfer characteristics—power supplies,
saturation,
• Circuit models—voltage/ current transresistance/
transconductance
• Frequency response—single time constant circuits,
bandwidth
BITS Pilani, Pilani Campus
Signals
Arbitrary in nature.
Obtained through sensors---variations converted into
current or voltage
Bits, pilani
BITS Pilani, Pilani Campus
Sinusoid
• Important signal in analysis , design, testing
• For an LTI system, if input is sinusoid, output is
also sinusoid with modified amplitude and
phase. Hence analysis is easy
• Every natural signal can be represented as sum
of sine waves of different frequencies and
amplitude.
• Lab testing is possible
Bits, pilani
BITS Pilani, Pilani Campus
Why amplifier first?
• Reasons—
• Fundamental signal processing function
• Employed in every electronic system
• Easy to understand
• Design techniques can be easily extended to design of
complex analog circuits.
• Similar to NOT gate in Digital Electronics
Bits, pilani
BITS Pilani, Pilani Campus
Amplifier circuit symbol
Bits, pilani
BITS Pilani, Deemed to be University under Section 3 of UGC Act, 1956
Amplifiers
Need- Weak signals- energy too small for reliable
processing
Requirement---Information contained in the signal should
not get changed/ Output must be exact replica of the
input.
Relation ship of amplifiers
vo(t) = A vi(t)
Bits, pilani
BITS Pilani, Pilani Campus
Characterizing parameters
• Gain
• Voltage swing
• Linearity
• Power efficiency
• Frequency response
• Power supply and dc bias
Bits, pilani
BITS Pilani, Pilani Campus
Analog Design tradeoffs
Bits, pilani
BITS Pilani
Pilani Campus
Gain/ transfer characteristics (VTC)
Gain/ transfer characteristics
Voltage Gain
Current gain
Power gain
Bits, pilani
BITS Pilani, Pilani Campus
VTC
Bits, pilani
Information from VTC
• Highest and Lowest signal amplitude
• Gain—steepness of transition
• Inverting/ non inverting nature
• Single/ dual power supply
• Offset
Bits, pilani
BITS Pilani, Pilani Campus
Voltage/ Power gain---
Gain in dB---10 log[ (Vo2/RL) / (Vi2/Ri)]
If RL= Ri
Gain in dB= 20 log (Vo/ Vi)
Power gain= 10 (Vo/ Vi)
Bits, pilani
BITS Pilani, Pilani Campus
Measuring Unit---Use of
Decibel unit
The decibel, or dB, is a means of expressing either the gain
of an active device (such as an amplifier) or the loss in a
passive device (such as an attenuator or length of
cable).
The decibel was developed by the telephone company to
conveniently express the gain or loss in telephone
transmission systems.
Bits, pilani
BITS Pilani, Pilani Campus
• Input >---- Amp #1 ---- Amp #2 ------> Output
• A1 = 275, A2 = 55
• The total gain factor At = 275 x 55 = 15,125.
• Use logarithms-
• log (A x B) = log A + log B
• log (A/B) = log A - log B
Bits, pilani
• Invented a unit of gain measurement called a
"Bel," named after Alexander Graham Bell.
• They defined the Bel as
Gain in Bels = log A = log (Po / Pi )
where A = Power amplification factor
Bits, pilani
• log 275 = 2.4393326 and
• log 55 = 1.7403626,
15,125
• so the total gain in our cascade is
• 2.4393326 + 1.7403626 = 4.179,695,289 Bels
• Rounding problem---
• 4.179 Bels15124.99----4.2 Bels15,849
• 5% error
Bits, pilani
• it was decided to express power gain in units
which were equal to one-tenth of a Bel, or in
deci-Bels
• 1 Bel=10 decibels
• Gain in decibels (dB) = 10 log A
• 2.4393326 + 1.7403626 = 4.179,695,289 Bels
• 24.39 + 17.40 = 41.79 decibels = 15,101
• 41.79 dB is a power gain of 15,101
• while 41.8 dB is a power gain of 15,136, so the error is
only 0.23%. Bits, pilani
Linearity
• Amplifier follows a relationship.--- linear
amplifier
• vo(t) = A vi(t)
• Any deviation (higher powers of vi) ---
nonlinear distortion
Bits, pilani
BITS Pilani, Pilani Campus
THD
Bits, pilani
Amplifier Power Supplies
• Important part of the circuit
• Power balance equation---
• Pdc + Pin = P load + P dissipated
• Maximum power must be delivered to the
load
• Figure of merit---Amplifier Power efficiency
PL
100
Pdc
BITS Pilani, Pilani Campus
Classes of amplifiers
Class A----ηmax = 25 %
Class B (~70%)
Class AB (~70%)
Class C (~80%)
Class D (~100%)
Bits, pilani
BITS Pilani, Pilani Campus
Example1-
BITS Pilani, Deemed to be University under Section 3 of UGC Act, 1956
Vcc vout
Q
Vcc/2
BITS Pilani, Deemed to be University under Section 3 of UGC Act, 1956
Practical VTC is non linear--
Saturation, varying slope
output will be distorted
--Operate at a point where VTC is
close to linear-middle
--Keep input small
BITS Pilani, Pilani Campus
BITS Pilani
Pilani Campus
Frequency Response
Frequency response-
bandwidth
• Ideal frequency response---gain does not
change with frequency
• Practical frequency response
Bits, pilani
BITS Pilani, Pilani Campus
Poles, Zeros and Bode Plots
Characterization:
K ( s z1 )( s z 2 ) ... ( s z m )
G (s)
s ( s p1 )( s p2 ) ... ( s pn )
s s s
( 1)( 1) ... ( 1)
K z1 z 2 z m z1 z2 zm
G (s)
p1 p2 pn s ( s 1)( s 1) ... ( s 1)
p1 p2 pn
K z1 z 2 z m
KB
p1 p2 pn
( z1s 1)( z 2 s 1) ... ( zm s 1)
G (s) K B
s ( p1s 1)( p 2 s 1) ... ( pn s 1)
(Time Constant Form.)
Characterization:
Considering the transfer function in the time constant form.
we have 4 different types of terms in the time constant form,
these are:
1 1
KB , , , (s / z 1)
s (s / p 1)
Expressing the transfer function dB:
j
KB ( 1)
G ( jw) z
j
(j )( 1)
0 p
20 log | G ( j ) |
j j
20 log K B 20 log | ( 1) | 20 log | j | 20 log | 1|
z o p
Mechanics: We have 4 distinct terms to consider:
20logKB ----- ( constant gain in time constant format)
- 20log|j /ω0 | ----- (Pole at origin if wo=1)
- 20log|(j /1 + |p|) ------ (Pole at 0 = p )
20log|(j/1 ±z)| ----- (zero at 0 = z )
wlg
1 1 1 1 1 1
This is a sheet of 5 cycle, semi-log paper.
This is the type of paper usually used for
preparing Bode plots.
dB Mag
Phase
(deg)
wlg
(rad/sec)
Frequency response plots
• Different types of transfer functions---
• K
w 1 jw 1
j w 1 jw
wo j wo 1
wo wo
Bits, pilani
K constant
Gain in dB
Log w
Ө= 0
Log w
jw/wo
Gain in dB
20 dB/ dec
wo
Log w
Ө= 90
Log w
-j wo/w = 1/ [jw/wo]
, pole at the origin, jw/w
w0=1 o
Gain in dB
20 dB/ dec
Log w
wo rad./ sec
For a pole at the origin draw a line with a slope of -20
Ө dB/decade that goes through 0 dB at 1 rad/sec
Log w
Ө= -90
1+ j (w/wo)
Gain in dB
Corner plot
20 dB/ dec
wo
Log w
Corner frequency
Ө
90
45
Ө= tan-1 (w/wo)
0.1 wo Log w
~10 wo
Magnitude and phase
jw
1
wo
1 / [1+ j (w/wo)]
Gain in dB
wo
Log w
20 dB/ dec
Ө
Ө= -tan-1 (w/wo)
~0.1 wo
Log w
-45
-90
~10 wo
Using Matlab For Frequency Response
Instruction: We can use Matlab to run the frequency response for the
previous example. We place the transfer function in the
form:
5000 ( s 10) [ 5000s 50000 ]
( s 1) ( s 500) [ s 2 501s 500]
The Matlab Program
num = [5000 50000];
den = [1 501 500];
Bode (num,den)
Using Matlab For Freq. Response
Instruction: We can use Matlab to run the frequency response for the
previous example. We place the transfer function in the
form:
5000 ( s 10) [ 5000s 50000 ]
( s 1) ( s 500) [ s 2 501s 500]
The Matlab Program
num = [5000 50000];
den = [1 501 500];
Bode (num,den)
Bode Diagrams
From: U(1)
40
30
20
Phase (deg); Magnitude (dB)
10
-10
1 10 100 500
0
-20
-40
To: Y(1)
-60
100(1 jw / 10)
Bode for: G ( jw)
-80 (1 jw)(1 jw / 500)
-100
10-1 100 101 102 103 104
Frequency (rad/sec)
G( j) tan1 ( / 10) tan1 ( / 1) tan1 ( / 500)
Initial angle=00 and final angle -900
Evaluating the frequency response
• Single time constant circuits
Vo (s) = 1/ [1+sCR] vi (s) Vo (s) = sCR/ [1+sCR] vi (s)
[vo./ vi]= K / [1+{s/wo}] [vo./ vi]= K s / [1+{s/wo}]
Bits, pilani
Bits, pilani
Bits, pilani
BITS Pilani
Pilani Campus
Amplifier circuit models
Bits, pilani
Amplifier circuit models-
analysis tools
Amplifiers must be characterized for its terminal behavior
first to be used as block in system design
For analysis purpose, complex circuits are replaced by their
(models)--- simple circuits
Voltage amplifier model (v,v)
Current amplifier (i,i)
Trans-conductance (v,i)
Trans-resistance (i,v)
Bits, pilani
BITS Pilani, Pilani Campus
Use 2 port network theory
Bits, pilani
BITS Pilani, Deemed to be University under Section 3 of UGC Act, 1956
Z parameter model
1/21/2019 Anu Gupta BITS PILANI
CLASSIFICATION OF AMPLIFIERS
Voltage amplifier
Ro
+ + +
vi Ri vo
Avvi
- -
-
Using the voltage divider rule open circuit voltage gain is
Av = vo/vi|io=0
Unit (V/V)
Ideal conditions: R0 = 0 Ri = condition for no loss
Bits, pilani
BITS Pilani, Pilani Campus
Current amplifier
ii io
+ +
Ri Aivi Ro vo
- -
Short-Circuit current gain
Ais = io/ii |vo=0
Unit (A/A)
Ideal conditions Ri = 0 ; R0 =
Bits, pilani
Trans-conductance amplifier
io
+ +
vi Ri Ro vo
Gmvi
- -
Short-Circuit Transconductance
Gm = io/vi |vo=0
Unit (A/V)
Ideal conditions Ri = ; R0 =
Bits, pilani
Trans-resistance amplifier
ii Ro
+
Ri vo
Rmii
-
Open-Circuit Transresistence
Rm = vo/ii |io=0
Unit (V/A)
Ideal conditions Ri = 0 ; R0 = 0
Bits, pilani
Relations between parameters
Av0 = Ais(Ro /Ri)
Av0 = GmRo
Av0 = Rm/Ri
Bits, pilani
BITS Pilani
Pilani Campus
Bipolar Junction Transistor
BJT
• The bipolar junction transistor, unlike other transistors, is
usually not a symmetrical device. This means that
interchanging the collector and the emitter makes the transistor
leave the forward active mode and start to operate in reverse
mode.
• Because the transistor's internal structure is usually optimized
for forward-mode operation, interchanging the collector and the
emitter makes the values of α and β in reverse operation much
smaller than those in forward operation; often the α of the
reverse mode is lower than 0.5.
• The lack of symmetry is primarily due to the doping ratios of the
emitter and the collector.
Bits, pilani
• The emitter is heavily doped, while the collector is lightly doped,
allowing a large reverse bias voltage to be applied before the
collector–base junction breaks down.
• The collector–base junction is reverse biased in normal
operation. The reason the emitter is heavily doped is to
increase the emitter injection efficiency: the ratio of carriers
injected by the emitter to those injected by the base. For high
current gain, most of the carriers injected into the emitter–base
junction must come from the emitter.
• The low-performance "lateral" bipolar transistors sometimes
used in CMOS processes are sometimes designed
symmetrically, that is, with no difference between forward and
backward operation.
Bits, pilani
Collector terminal
• The area of collector layer is largest. So it can dissipate
heat quickly. IT is normally in direct contact with the metal
case of the transistor, or a metal mounting pad, which may
then be bolted or clipped directly on to a heat-sink.
• The collector needs to be lightly doped so that the
collector-base junction will have a high breakdown voltage.
This translates into a high allowable collector power supply
voltage. Small signal silicon transistors have a 60-80 V
breakdown voltage. Though, it may run to hundreds of
volts for high voltage transistors.
• The collector also needs to be heavily doped to minimize ohmic
losses if the transistor must handle high current. These
contradicting requirements are met by doping the collector
more heavily at the metallic contact area. The collector near the
base is lightly doped as compared with the emitter.
• The heavy doping in the emitter gives the emitter-base a low
approximate 7 V breakdown voltage in small signal transistors.
Bits, pilani
END
Bits, pilani