Scribd
Upload
13K views6 pages

Reinforcement Detailing of RCC Slabs

Reinforcement detailing of slabs depends on the slab's support conditions. Slabs can be one-way or two-way, with one-way slabs having a longer span in one direction and two-way slabs being supported on all four sides. Additional torsion reinforcement is required at restrained corners of two-way slabs. Reinforcement amounts are determined by slab thickness, span, and material strength according to codes.

Uploaded by

Gani Anosa
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
13K views6 pages

Reinforcement Detailing of RCC Slabs

Reinforcement detailing of slabs depends on the slab's support conditions. Slabs can be one-way or two-way, with one-way slabs having a longer span in one direction and two-way slabs being supported on all four sides. Additional torsion reinforcement is required at restrained corners of two-way slabs. Reinforcement amounts are determined by slab thickness, span, and material strength according to codes.

Uploaded by

Gani Anosa
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 6

REINFORCEMENT DETAILING OF RCC

SLABS
Home » How To Guide » Detailing Guide » REINFORCEMENT DETAILING OF RCC SLABS

Reinforcement detailing of a slab is done based on its support conditions.


Slab may be supported on walls or beams or columns. Slab supported
directly by columns are called flat slab.

Slab supported on two sides and bending takes place predominantly in one
direction only is called One Way Slab. On the other hand, when slab is
supported on all four sides and bending take place in two directions are said
to be Two Way Slab.

The slabs having ratio of longer length to its shorter length (Ly/Lx) greater
than 2 is called one way slab otherwise as two way slab. In one way slab
main reinforcement is parallel to shorter direction and the reinforcement
parallel to longer direction is called distribution steel. In two way slab main
reinforcement is provided along both direction.
Slabs could be simply supported, continuous or cantilever. In two way slab
the corners may be held down by restraints or may be allowed to lift up.
Additional torsion reinforcement is required at corners when it is restrained
against uplifting as shown in Fig.1.
Thickness of the slab is decided based on span to depth ratio specified in
IS456-2000. Min reinforcement is 0.12% for HYSD bars and 0.15% for mild
steel bars. The diameter of bar generally used in slabs are: 6 mm, 8 mm, 10
mm, 12 mm and 16 mm.
The maximum diameter of bar used in slab should not exceed 1/8 of the total
thickness of slab. Maximum spacing of main bar is restricted to 3 times
effective depth or 300 mm whichever is less. For distribution bars the
maximum spacing is specified as 5 times the effective depth or 450 mm
whichever is less.
Minimum clear cover to reinforcements in slab depends on the durability criteria
and this is specified in IS 456-200. Generally 15 mm to 20 mm cover is
provided for the main reinforcements. Alternate main bars can be cranked
near support or could be bent at 1800 at the edge and then extended at the
top inside the slab as shown in Fig.1. Curtailment and cranking of bars and
is shown in Fig. 2.

Torsion reinforcement shall be provided at any corner where the slab is


simply supported on both edges meeting at that corner and is prevented
from lifting unless the consequences of cracking are negligible. It shall
consist of top and bottom reinforcement, each with layer of bars placed
parallel to the sides of the slab and extending from the edges a minimum
distance of one fifth of the shorter span. The area of reinforcement per unit
width in each of these four layers shall be three quarters of the area
required for the maximum mid-span moment per unit width in the slab.
Torsion reinforcement equal to half that described above shall be provided at
a corner contained by edges over only one of which the slab is continuous.
Torsion reinforcement to be provided is shown in Fig. 3 below.
The drawing showing the detailing of reinforcement has a plan showing
typical reinforcement in both direction and sectional elevations. Typical
detailing of slab is shown in Fig.4 and 5.
Fig.4:
Slab spanning in one direction (One-way slab)
Fig.5:
Slab spanning in two-directions (two-way slab)

You might also like