Scribd
Upload
108 views

Beam Calc Web Example

Plan Analyst allows users to quickly check beams and columns for code compliance by filling out forms with beam/column descriptions and load details. It then performs all necessary calculations and provides a detailed drawing and results. This allows designers to efficiently try different options during design or quickly check plans during review. Interactive features let users immediately see the impact of changes without clicking additional buttons.

Uploaded by

Jasi
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
108 views

Beam Calc Web Example

Plan Analyst allows users to quickly check beams and columns for code compliance by filling out forms with beam/column descriptions and load details. It then performs all necessary calculations and provides a detailed drawing and results. This allows designers to efficiently try different options during design or quickly check plans during review. Interactive features let users immediately see the impact of changes without clicking additional buttons.

Uploaded by

Jasi
Copyright
© Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

HOW DO I CHECK A BEAM USING PLAN ANALYST?

• First you simply fill in the Plan Analyst forms to complete the beam or column
description as shown below.
• Plan Analyst will then complete all of the time consuming calculations and create
a detailed drawing of this beam or column.

1. If you are in the design process, you can quickly try different beam sizes or
types of material to determine the best beam or column for this location. Now
you have complete confidence in code compliance, preventing delays when the
plans are submitted for approval.
2. If you are checking the plans for code compliance, you can quickly check
beams and columns. Plan analyst contains many different types of beams so
there is no need to change software or the procedure you use when the
project contains several different types of beams. This will make the plan
review process faster, easier and more accurate.

USING THE BEAM DESCRIPTION TAB


Select Beam Material from the list box
on the left bottom of the screen.
Click on the name of material
1. Now Select the Grade of
Material. Note: The materials
grade box will change
depending on the material name
you choose in the first box and
will only show if there is more
than one grade available. Click
on the desired grade. Note:
Grade will always default to
last one selected.
2. Shear increase will only show
for 2X_, 4X_ and 6X_ material.
3. Select the size of the beam by
clicking the size in the Select
Size list box.
4. If multiple members are allowed,
click the number of members. If
multiple members are not
allowed, the box will not be
shown.

USING THE LOADS ON BEAM TAB

1. Select load condition Note: The


Loads on Beam box will change to
match load condition selected.
2. Select support at bearing points
3. Select Deflection limits
4. Select Meets repetitive member
requirements To use repetitive
member, click box to place a √ in
the box. Note: This will only be
displayed when you have selected
visually graded wood.
5. Select Duration of Load This
option is only available for wood
members.
SELECT LOAD CONDITION
1. Single span with one uniform load
This is the most common loading condition for beams and headers.

2. Cantilever with uniform and/or point load at end


This is great for cantilevered joist supporting a wall at the end.

3. Single span with an increasing load


The most common use for this option is for the corner rafter of a hip system or for a
valley rafter. This loading condition starts at zero and increases to a maximum at the
other end.

4. Multiple uniform and/or point loads


This is good for a beam that supports another beam plus rafters and/or joists. It is also
good for beams supporting joists and/or rafters that vary in length. Another use is for
a beam that supports rafters on part of the beam and supports joists on the other part
of the beam.

5. Continuous beam over two spans


This is for beams with uniform loads and multiple supports. A beam in the center of a
building would be the common location for this type of beam.

CHECKING DIFFERENT BEAMS


To try a different beam size or type, click the Beam Description tab, select the new size
and/or beam material and click the Check button. The results for the new beam will be
shown instantly.

2
CHECKING A COLUMN
1. Enter the column height.
2. Indicate if Column has a wood
plate, joist or beam at the top
or bottom. Note: Wood cannot
support as much weight on
sides as it can on ends. If you
select this, compression
perpendicular to grain will be
checked and allowable
bearing will be adjusted if
necessary.
3. If column is braced with
sheathing, it controls
buckling, therefore increasing
allowable. Note: Some
sheathing is not strong enough
to control buckling. Check
sheathing before selecting
this.
4. The rest of input is similar to
the beam input described
above.

The Column Calculator is interactive. Current results show instantly each time you make
a change . There is no need to click the Check button to see the results.

The maximum load that the column can support is shown above the column in the picture
and at the bottom of the results.

USING THE CALCULATOR


When numbers, such as dimensions and square footage, are required, a four-function
calculator is built into plan analyst. use the + for addition - for subtraction x or * for
multiplication and / for division. Algebraic logic is used (i.e. division and multiplication are
always completed before addition and subtraction)
There is no need to reach for your calculator.
When asked for the floor area enter: 100 x 40 + 30 x 38 and the floor
area will be calculated for you.

You might also like