0% found this document useful (0 votes)
80 views33 pages

CMOS Logic: Sudhanshu Janwadkar, Teaching Assistant, SVNIT, Surat Lecture Notes 16-17 February 2017

The document discusses CMOS logic and MOSFET transistors. It begins by introducing the basic MOS structure and how CMOS uses both n-type and p-type transistors. It then explains how an n-type MOSFET and p-type MOSFET work by manipulating the electric fields near the gate to allow or block current flow. Common CMOS gates like inverters and NAND/NOR gates are constructed using both types of transistors. The document also discusses concepts like weak 1s/0s that occur when using single transistor pass gates and how transmission gates improve this using both transistor types.

Uploaded by

baditakali
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
80 views33 pages

CMOS Logic: Sudhanshu Janwadkar, Teaching Assistant, SVNIT, Surat Lecture Notes 16-17 February 2017

The document discusses CMOS logic and MOSFET transistors. It begins by introducing the basic MOS structure and how CMOS uses both n-type and p-type transistors. It then explains how an n-type MOSFET and p-type MOSFET work by manipulating the electric fields near the gate to allow or block current flow. Common CMOS gates like inverters and NAND/NOR gates are constructed using both types of transistors. The document also discusses concepts like weak 1s/0s that occur when using single transistor pass gates and how transmission gates improve this using both transistor types.

Uploaded by

baditakali
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 33

CMOS Logic

Sudhanshu Janwadkar, Teaching Assistant, SVNIT, Surat


Lecture Notes 16-17th February 2017
Introduction
 Metal-Oxide-Semiconductor (MOS) structure is created by superimposing
several layers of conducting and insulating materials to form a sandwich-
like structure.
 These structures are manufactured using a series of chemical processing
steps involving oxidation of the silicon, selective introduction of dopants,
and deposition and etching of metal wires and contacts.
 CMOS technology provides two types of transistors: an n-type transistor
(nMOS) and a p-type transistor (pMOS).
 Transistor operation is controlled by electric fields so the devices are also
called Metal Oxide Semiconductor Field Effect Transistors (MOSFETs)
Introduction
 Each transistor consists of a stack of the conducting gate, an insulating
layer of silicon dioxide (SiO2), and the silicon wafer, also called the
substrate, or body, or bulk.
 An nMOS transistor is built with a p-type body and has regions of n-type
semiconductor adjacent to the gate called the source and drain
 A pMOS consists of p-type source and drain regions with an n-type body.
 In a CMOS technology, with both flavors of transistors, the substrate is
either n-type or p-type.
 The other flavor of transistor must be built in a special well in which dopant
atoms have been added to form the body of the opposite type.
MOS Principle

 The gate is a control input: It affects the flow of electrical current between the
source and drain.
N-channel MOSFET
 Consider an nMOS transistor.
 The body is generally grounded so the p–n junctions of the source and
drain to body are reverse-biased.
 If the gate is also grounded, no current flows through the reverse-biased
junctions. Hence, we say the transistor is OFF.
 If the gate voltage is raised, it creates an electric field that starts to attract
free electrons to the underside of the Si–SiO2 interface.
 If the voltage is raised enough, the electrons outnumber the holes and a
thin region under the gate called the channel is inverted to act as an n-
type semiconductor.
 Hence, a conducting path of electron carriers is formed from source to
drain and current can flow. We say the transistor is ON.
P-channel MOSFET

 For a pMOS transistor, The body is held at a positive voltage.


 When the gate is also at a positive voltage, the source and drain junctions are
reverse-biased and no current flows, so the transistor is OFF.
 When the gate voltage is lowered, positive charges are attracted to the underside
of the Si–SiO2 interface.
 A sufficiently low gate voltage inverts the channel and a conducting path of
positive carriers is formed from source to drain, so the transistor is ON.
MOSFET as Switch

 The gate of an MOS transistor controls the flow of current between the source and
drain
 Simplifying this to the extreme allows the MOS transistors to be viewed as simple
ON/OFF switches.
 When the gate of an nMOS transistor is 1, the transistor is ON and there is a
conducting path from source to drain.
 When the gate is low, the nMOS transistor is OFF and almost zero current flows
from source to drain.
 A pMOS transistor is just the opposite, being ON when the gate is low and OFF
when the gate is high.
CMOS Inverter
 When the input A is 0, the nMOS transistor is OFF and the pMOS transistor is ON.
Thus, the output Y is pulled up to 1 because it is connected to
 VDD but not to GND.
 Conversely, when A is 1, the nMOS is ON, the pMOS is OFF, and Y is pulled down
to ‘0.’
 Schematic and Symbol for a CMOS inverter

 The bar at the top indicates VDD and the triangle at the bottom indicates GND.
CMOS NAND Gate

Gate Schematic Symbol


CMOS NAND Gate
 It consists of two series nMOS transistors between Y and GND and two
parallel pMOS transistors between Y and VDD.
 If either input A or B is 0:
 At least one of the nMOS transistors will be OFF, breaking the path
from Y to GND.
 But at least one of the pMOS transistors will be ON, creating a path
from Y to VDD.
 Hence, the output Y will be 1.
 If both inputs are 1,
 both of the nMOS transistors will be ON and
 both of the pMOS transistors will be OFF.
 Hence, the output will be 0.
CMOS NAND Gate
CMOS Logic Structure
CMOS Logic Structure
 In general, a static CMOS gate has
 an nMOS pull-down network to connect the output to 0 (GND) and
 pMOS pull-up network to connect the output to 1 (VDD)
 In general, when we join a pull-up network to a pull-down network to form
a logic gate, they both will attempt to exert a logic level at the output.
 The networks are arranged such that one is ON and the other OFF for any
input pattern.
Connection and behaviour of series and parallel
transistors
CMOS NOR Gate
 The nMOS transistors are in parallel to pull the output low when either input is
high.
 The pMOS transistors are in series to pull the output high when both inputs are low
3 input NOR Gate??
3 input NOR Gate
3 input NAND Gate??
3 input NAND Gate
Compound Gates
Compound Gates
Combinational Circuits
Pass Transistors and Transmission Gates

 The strength of a signal is measured by how closely it approximates an


ideal voltage source.
 The power supplies, or rails, (VDD and GND) are the source of the
strongest 1s and 0s.
 An nMOS transistor is an almost perfect switch when passing a 0 and thus
we say it passes a strong 0. However, the nMOS transistor is imperfect at
passing a 1. We say it passes a degraded or weak 1.

 An pMOS transistor is an almost perfect switch when passing a 1 and


thus we say it passes a strong 1. However, the nMOS transistor is
imperfect at passing a 1. We say it passes a degraded or weak 0
Pass Transistors and Transmission Gates

Concept of Weak 1:

Consider an nMOS transistor with the Gate and Drain tied to VDD.
Imagine that the source is initially at Vs = 0. Vgs > Vtn, so the transistor is ON and
current flows.

If the voltage on the source rises to Vs = VDD – Vtn, Vgs falls to Vtn and the transistor
cuts itself OFF.
Therefore, nMOS transistors attempting to pass a 1 never pull the source above
VDD – Vtn. This loss is called threshold drop.
Pass Transistors and Transmission Gates

Concept of Weak 0:
Similarly, pMOS transistors pass 1s well but 0s poorly. If the pMOS source drops below |Vtp|,
the transistor cuts off.

Hence, pMOS transistors only pull down to within a threshold above GND,
Pass Transistors and Transmission Gates
 When an nMOS or pMOS is used alone as an imperfect switch, we call it a
pass transistor.
Pass Transistors and Transmission Gates
 By combining an nMOS and a pMOS transistor in parallel, we obtain a switch,
which 0s and 1s are both passed in an acceptable fashion.
 We term this a transmission gate or pass gate.

You might also like