Scribd
Upload
48 views5 pages

Chapter I-Stress: (66.7 Kpa, 115 Kpa)

This document contains 9 problems related to determining stresses in mechanical components and structures subjected to various forces. The problems involve calculating normal stresses, shear stresses, required member dimensions, and maximum loads based on allowable stress values. The document provides stress analysis questions that are typical of introductory mechanics of materials or strength of materials courses.

Uploaded by

Irem Dolek
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
48 views5 pages

Chapter I-Stress: (66.7 Kpa, 115 Kpa)

This document contains 9 problems related to determining stresses in mechanical components and structures subjected to various forces. The problems involve calculating normal stresses, shear stresses, required member dimensions, and maximum loads based on allowable stress values. The document provides stress analysis questions that are typical of introductory mechanics of materials or strength of materials courses.

Uploaded by

Irem Dolek
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

CHAPTER I- STRESS

1- The beam is supported by a pin at A and a short link BC. Determine the maximum
magnitude P of the loads the beam will support if the average shear stress in each
pin is not to exceed 80 MPa. All pins are in double shear as shown, and each has a
diameter of 18 mm.
(P = 3.70 kN)

2- The block is subjected to a compressive force of 2 kN. Determine the average


normal and average shear stress developed in the wood fibers that are oriented
along section a–a at 30° with the axis of the block.

(66.7 kPa, 115 kPa)

3- If the joint is subjected to an axial force of P=9 kN , determine the average shear
stress developed in each of the 6-mm diameter bolts between the plates and the
members and along each of the four shaded shear planes.

(79.6 MPa, 225 kPa)


4- The shaft is subjected to the axial force of 40 kN. Determine the average bearing
stress acting on the collar C and the normal stress in the shaft.
(56.6 MPa, 31.8 MPa)

5- Determine the largest load P that can be a applied to the frame without causing
either the average normal stress or the average shear stress at section a–a to exceed
 =150 MPa and  =60 MPa, respectively. Member CB has a square cross section of
25 mm on each side.
(62.5 kN)
6- The lever is attached to the shaft A using a key that has a width d and length of
25 mm. If the shaft is fixed and a vertical force of 200 N is applied perpendicular to
the handle, determine the dimension d if the allowable shear stress for the key is
 allow = 35 MPa.

(5.71 mm)

7- The wood specimen is subjected to the pull of 10 kN in a tension testing machine.


If the allowable normal stress for the wood is  all =12 MPa and the allowable shear
stress is  all =1.2 MPa determine the required dimensions b and t so that the
specimen reaches these stresses simultaneously.The specimen has a width of 25
mm.
(167 mm, 33,3 mm)
8- The joint is used to transmit a torque of T=3 kN.m. Determine the required
minimum diameter of the shear pin A if it is made from a material having a shear
failure stress of  fail =150 MPa. Apply a factor of safety of 3 against failure.

(27.6 mm)

9- The frame is subjected to the load of 4 kN which acts on member ABD at D.


Determine the required diameter of the pins at D and C if the allowable shear stress
 all =40 MPa for the material is Pin C is subjected to double shear, whereas pin D is
subjected to single shear.

(12 mm, 14 mm)

You might also like