Scribd
Upload
34 views2 pages

For If Else End End

The document describes binary amplitude-shift keying (ASK) modulation and demodulation. It defines a binary information sequence, modulates it onto a carrier signal by varying the signal amplitude, transmits the modulated signal, then demodulates and recovers the original binary sequence. Key steps include generating a digital signal from the binary sequence, ASK modulating it onto a carrier, demodulating by detecting the signal amplitude, and recovering the binary sequence.

Uploaded by

Yonathan Setiawan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
34 views2 pages

For If Else End End

The document describes binary amplitude-shift keying (ASK) modulation and demodulation. It defines a binary information sequence, modulates it onto a carrier signal by varying the signal amplitude, transmits the modulated signal, then demodulates and recovers the original binary sequence. Key steps include generating a digital signal from the binary sequence, ASK modulating it onto a carrier, demodulating by detecting the signal amplitude, and recovering the binary sequence.

Uploaded by

Yonathan Setiawan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

ASK

x=[ 1 0 0 1 1 0 1]; % Binary Information


bp=.000001; % bit period
disp(' Binary information at Trans mitter :');
disp(x);
%XX representation of transmitting binary information as digital signal XXX
bit=[];
for n=1:1:length(x)
if x(n)==1;
se=ones(1,100);
else x(n)==0;
se=zeros(1,100);
end
bit=[bit se];
end
t1=bp/100:bp/100:100*length(x)*(bp/100);
subplot(3,1,1);
plot(t1,bit,'lineWidth',2.5);grid on;
axis([ 0 bp*length(x) -.5 1.5]);
ylabel('amplitude(volt)');
xlabel(' time(sec)');
title('transmitting information as digital signal');
%XXXXXXXXXXXXXXXXXXXXXXX Binary-ASK modulation XXXXXXXXXXXXXXXXXXXXXXXXXXX%
A1=10; % Amplitude of carrier signal for information 1
A2=5; % Amplitude of carrier signal for information 0
br=1/bp; % bit rate
f=br*10; % carrier frequency
t2=bp/99:bp/99:bp;
ss=length(t2);
m=[];
for (i=1:1:length(x))
if (x(i)==1)
y=A1*cos(2*pi*f*t2);
else
y=A2*cos(2*pi*f*t2);
end
m=[m y];
end
t3=bp/99:bp/99:bp*length(x);
subplot(3,1,2);
plot(t3,m);
xlabel('time(sec)');
ylabel('amplitude(volt)');
title('waveform for binary ASK modulation coresponding binary information');
%XXXXXXXXXXXXXXXXXXXX Binary ASK demodulation XXXXXXXXXXXXXXXXXXXXXXXXXXXXX
mn=[];
for n=ss:ss:length(m)
t=bp/99:bp/99:bp;
y=cos(2*pi*f*t); % carrier siignal
mm=y.*m((n-(ss-1)):n);
t4=bp/99:bp/99:bp;
z=trapz(t4,mm) % intregation
zz=round((2*z/bp))
if(zz>7.5) % logic level = (A1+A2)/2=7.5
a=1;
else
a=0;
end
mn=[mn a];
end
disp(' Binary information at Reciver :');
disp(mn);
%XXXXX Representation of binary information as digital signal which achived
%after ASK demodulation XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
bit=[];
for n=1:length(mn);
if mn(n)==1;
se=ones(1,100);
else mn(n)==0;
se=zeros(1,100);
end
bit=[bit se];
end
t4=bp/100:bp/100:100*length(mn)*(bp/100);
subplot(3,1,3)
plot(t4,bit,'LineWidth',2.5);grid on;
axis([ 0 bp*length(mn) -.5 1.5]);
ylabel('amplitude(volt)');
xlabel(' time(sec)');
title('recived information as digital signal after binary ASK demodulation');
%>>>>>>>>>>>>>>>>>>>>>>>>>> end of program >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>%

transmitting information as digital signal


amplitude(volt)

1.5
1
0.5
0
-0.5
0 1 2 3 4 5 6 7
time(sec) -6
x 10
waveform for binary ASK modulation coresponding binary information
amplitude(volt)

10

-10
0 1 2 3 4 5 6 7
time(sec) -6
x 10
recived information as digital signal after binary ASK demodulation
amplitude(volt)

1.5
1
0.5
0
-0.5
0 1 2 3 4 5 6 7
time(sec) -6
x 10

You might also like