Taskalfa 3050ci PDF

TASKalfa 3050ci
TASKalfa 3550ci
TASKalfa 4550ci
TASKalfa 5550ci
SERVICE
MANUAL
Published in January 2011
842LC110
2LCSM060
First Edition
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE

OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
It may be illegal to dispose of this battery into the municipal waste stream. Check with your
local solid waste officials for details in your area for proper disposal.
ATTENTION
IL Y A UN RISQUE D’EXPLOSION SI LA BATTERIE EST REMPLACEE PAR UN MODELE

DE TYPE INCORRECT. METTRE AU REBUT LES BATTERIES UTILISEES SELON LES
INSTRUCTIONS DONNEES.
Il peut être illégal de jeter les batteries dans des eaux d’égout municipales. Vérifiez avec les
fonctionnaires municipaux de votre région pour les détails concernant des déchets solides
et une mise au rebut appropriée.
Notation of products in the manual
For the purpose of this service manual, products are identified by print speed at A4 and
black and white modes.
TASKalfa 3050ci: 30 ppm model

Revision history
Revision Date Replaced pages Remarks
This page is intentionally left blank.
Safety precautions
This booklet provides safety warnings and precautions for our service personnel to ensure the safety of
their customers, their machines as well as themselves during maintenance activities. Service personnel
are advised to read this booklet carefully to familiarize themselves with the warnings and precautions
described here before engaging in maintenance activities.
Safety warnings and precautions
Various symbols are used to protect our service personnel and customers from physical danger and
to prevent damage to their property. These symbols are described below:
DANGER: High risk of serious bodily injury or death may result from insufficient attention to or incorrect
compliance with warning messages using this symbol.
WARNING: Serious bodily injury or death may result from insufficient attention to or incorrect compliance
with warning messages using this symbol.
CAUTION: Bodily injury or damage to property may result from insufficient attention to or incorrect com-
pliance with warning messages using this symbol.
Symbols
The triangle ( ) symbol indicates a warning including danger and caution. The specific point of attention is
shown inside the symbol.
General warning. Warning of risk of electric shock.
Warning of high temperature.
indicates a prohibited action. The specific prohibition is shown inside the symbol.
General prohibited action. Disassembly prohibited.
indicates that action is required. The specific action required is shown inside the symbol.
General action required. Remove the power plug from the wall outlet.
Always ground the copier.

1. Installation Precautions
WARNING
• Do not use a power supply with a voltage other than that specified. Avoid multiple connections to
one outlet: they may cause fire or electric shock. When using an extension cable, always check that
it is adequate for the rated current. .....................................................................................................
• Connect the ground wire to a suitable grounding point. Not grounding the copier may cause fire or
electric shock. Connecting the earth wire to an object not approved for the purpose may cause
explosion or electric shock. Never connect the ground cable to any of the following: gas pipes, light-
ning rods, ground cables for telephone lines and water pipes or faucets not approved by the proper
authorities. ..........................................................................................................................................
CAUTION:
• Do not place the copier on an infirm or angled surface: the copier may tip over, causing injury. .........
• Do not install the copier in a humid or dusty place. This may cause fire or electric shock. .................
• Do not install the copier near a radiator, heater, other heat source or near flammable material. This
may cause fire. ...................................................................................................................................
• Allow sufficient space around the copier to allow the ventilation grills to keep the machine as cool
as possible. Insufficient ventilation may cause heat buildup and poor copying performance. ............
• Always handle the machine by the correct locations when moving it. .................................................
• Always use anti-toppling and locking devices on copiers so equipped. Failure to do this may cause
the copier to move unexpectedly or topple, leading to injury. ..............................................................
• Avoid inhaling toner or developer excessively. Protect the eyes. If toner or developer is accidentally
ingested, drink a lot of water to dilute it in the stomach and obtain medical attention immediately.
If it gets into the eyes, rinse immediately with copious amounts of water and obtain medical atten-
tion. .....................................................................................................................................................
• Advice customers that they must always follow the safety warnings and precautions in the copier’s
instruction handbook. .........................................................................................................................
2. Precautions for Maintenance
WARNING
• Always remove the power plug from the wall outlet before starting machine disassembly. ................
• Always follow the procedures for maintenance described in the service manual and other related
brochures. ..........................................................................................................................................
• Under no circumstances attempt to bypass or disable safety features including safety mechanisms
and protective circuits. ........................................................................................................................
• Always use parts having the correct specifications. ............................................................................
• Always use the thermostat or thermal fuse specified in the service manual or other related brochure
when replacing them. Using a piece of wire, for example, could lead to fire or other serious acci-
dent. ...................................................................................................................................................
• When the service manual or other serious brochure specifies a distance or gap for installation of a
part, always use the correct scale and measure carefully. ..................................................................
• Always check that the copier is correctly connected to an outlet with a ground connection. ...............
• Check that the power cable covering is free of damage. Check that the power plug is dust-free. If it
is dirty, clean it to remove the risk of fire or electric shock. .................................................................
• Never attempt to disassemble the optical unit in machines using lasers. Leaking laser light may
damage eyesight. ...............................................................................................................................
• Handle the charger sections with care. They are charged to high potentials and may cause electric
shock if handled improperly. ...............................................................................................................
CAUTION
• Wear safe clothing. If wearing loose clothing or accessories such as ties, make sure they are safely
secured so they will not be caught in rotating sections. ......................................................................
• Use utmost caution when working on a powered machine. Keep away from chains and belts. ..........
• Handle the fixing section with care to avoid burns as it can be extremely hot. ..................................
• Check that the fixing unit thermistor, heat and press rollers are clean. Dirt on them can cause
abnormally high temperatures. ...........................................................................................................
• Do not remove the ozone filter, if any, from the copier except for routine replacement. ......................
• Do not pull on the AC power cord or connector wires on high-voltage components when removing
them; always hold the plug itself. ........................................................................................................
• Do not route the power cable where it may be stood on or trapped. If necessary, protect it with a
cable cover or other appropriate item. ................................................................................................
• Treat the ends of the wire carefully when installing a new charger wire to avoid electric leaks. ..........
• Remove toner completely from electronic components. .....................................................................
• Run wire harnesses carefully so that wires will not be trapped or damaged. ......................................
• After maintenance, always check that all the parts, screws, connectors and wires that were
removed, have been refitted correctly. Special attention should be paid to any forgotten connector,
trapped wire and missing screws. .......................................................................................................
• Check that all the caution labels that should be present on the machine according to the instruction
handbook are clean and not peeling. Replace with new ones if necessary. .......................................
• Handle greases and solvents with care by following the instructions below: ......................................
· Use only a small amount of solvent at a time, being careful not to spill. Wipe spills off completely.
· Ventilate the room well while using grease or solvents.
· Allow applied solvents to evaporate completely before refitting the covers or turning the power
switch on.
· Always wash hands afterwards.
• Never dispose of toner or toner bottles in fire. Toner may cause sparks when exposed directly to
fire in a furnace, etc. ...........................................................................................................................
• Should smoke be seen coming from the copier, remove the power plug from the wall outlet immedi-
ately. ...................................................................................................................................................
3. Miscellaneous
WARNING
• Never attempt to heat the drum or expose it to any organic solvents such as alcohol, other than the
specified refiner; it may generate toxic gas. ........................................................................................
2LK/2LN/2LM/2LC
CONTENTS
1-1 Specifications
1-1-1 Specifications ........................................................................................................................ 1-1-1
1-1-2 Parts names .......................................................................................................................... 1-1-6
(1) Machine ............................................................................................................................ 1-1-6
(2) Option ............................................................................................................................... 1-1-8
(3) Operation panel ................................................................................................................ 1-1-9
1-1-3 Machine cross section ......................................................................................................... 1-1-10
1-2 Installation
1-2-1 Installation environment......................................................................................................... 1-2-1
1-2-2 Unpacking and installation..................................................................................................... 1-2-2
(1) Installation procedure ....................................................................................................... 1-2-2
(2) Setting initial copy modes............................................................................................... 1-2-18
1-3 Maintenance Mode

1-3-1 Maintenance mode ................................................................................................................ 1-3-1
(1) Executing a maintenance item ......................................................................................... 1-3-1
(2) Maintenance modes item list ............................................................................................ 1-3-2
(3) Contents of the maintenance mode items ...................................................................... 1-3-10
1-4 Troubleshooting
1-4-1 Paper misfeed detection ........................................................................................................ 1-4-1
(1) Paper misfeed indication .................................................................................................. 1-4-1
(2) Paper misfeed detection condition ................................................................................... 1-4-2
1-4-2 Self-diagnostic function ....................................................................................................... 1-4-26
(1) Self-diagnostic function .................................................................................................. 1-4-26
(2) Self diagnostic codes...................................................................................................... 1-4-27
1-4-3 Image formation problems ................................................................................................... 1-4-87
(1) No image appears (entirely white).................................................................................. 1-4-88
(2) No image appears (entirely black).................................................................................. 1-4-89
(3) Image is too light. ........................................................................................................... 1-4-90
(4) The background is colored. ............................................................................................ 1-4-90
(5) White streaks are printed vertically................................................................................. 1-4-91
(6) Black streaks are printed vertically. ................................................................................ 1-4-91
(7) Streaks are printed horizontally. ..................................................................................... 1-4-91
(8) One side of the print image is darker than the other. ..................................................... 1-4-92
(9) Spots are printed. ........................................................................................................... 1-4-92
(10) Image is blurred.............................................................................................................. 1-4-92
(11) The leading edge of the image is consistently misaligned with the original. .................. 1-4-93
(12) The leading edge of the image is sporadically misaligned with the original. .................. 1-4-93
(13) Paper is wrinkled. ........................................................................................................... 1-4-93
(14) Offset occurs. ................................................................................................................. 1-4-94
(15) Part of image is missing. ................................................................................................ 1-4-94
(16) Fusing is loose................................................................................................................ 1-4-94
(17) Image is out of focus. ..................................................................................................... 1-4-95
(18) Image center does not align with the original center. ..................................................... 1-4-95
1-4-4 Electric problems ................................................................................................................. 1-4-96
1-4-5 Mechanical problems......................................................................................................... 1-4-104
1-4-6 Send error code ................................................................................................................. 1-4-106
(1) Scan to SMB error codes ............................................................................................. 1-4-106
(2) Scan to FTP error codes .............................................................................................. 1-4-107
2LK/2LN/2LM/2LC
(3) Scan to E-mail error codes ........................................................................................... 1-4-108

1-4-7 Error codes ........................................................................................................................ 1-4-109
(1) Error code..................................................................................................................... 1-4-109
(2) Table of general classification ...................................................................................... 1-4-110
(2-1) U004XX error code table: Interrupted phase B ................................................... 1-4-112
(2-2) U006XX error code table: Problems with the unit ............................................... 1-4-112
(2-3) U008XX error code table: Page transmission error............................................. 1-4-112
(2-4) U009XX error code table: Page reception error .................................................. 1-4-112
(2-5) U010XX error code table: G3 transmission......................................................... 1-4-113
(2-6) U011XX error code table: G3 reception .............................................................. 1-4-114
(2-7) U017XX error code table: V.34 transmission ...................................................... 1-4-115
(2-8) U018XX error code table: V.34 reception............................................................ 1-4-115
1-5 Assembly and disassembly

1-5-1 Precautions for assembly and disassembly........................................................................... 1-5-1
(1) Precautions....................................................................................................................... 1-5-1
(2) Drum................................................................................................................................. 1-5-1
(3) Toner ................................................................................................................................ 1-5-1
(4) How to tell a genuine Kyocera Mita toner container ......................................................... 1-5-2
1-5-2 Paper feed section................................................................................................................. 1-5-3
(1) Detaching and refitting the primary feed unit.................................................................... 1-5-3
(2) Detaching and refitting the forwarding pulley, paper feed pulley and separation pulley.
[30 ppm model / 35 ppm model] ...................................................................................... 1-5-7
(3) Detaching and refitting the forwarding pulley, paper feed pulley and separation pulley.
[45 ppm model / 55 ppm model] ..................................................................................... 1-5-10
(4) Detaching and refitting the MP tray paper feed unit ....................................................... 1-5-11
(5) Detaching and refitting the MP forwarding pulley, MP paper feed pulley and
MP separation pulley ...................................................................................................... 1-5-14
1-5-3 Optical section ..................................................................................................................... 1-5-19
(1) Detaching and refitting the exposure lamp ..................................................................... 1-5-19
(2) Detaching and refitting the ISU....................................................................................... 1-5-22
(3) Detaching and refitting the LSU...................................................................................... 1-5-25
(4) Color registration adjustment.......................................................................................... 1-5-31
1-5-4 Image formation section ...................................................................................................... 1-5-34
(1) Detaching and refitting the inner unit.............................................................................. 1-5-34
(2) Detaching and refitting the developer unit and drum unit ............................................... 1-5-36
(3) Detaching and refitting the charger roller unit................................................................. 1-5-38
1-5-5 Transfer section ................................................................................................................... 1-5-39
(1) Detaching and refitting the conveying unit...................................................................... 1-5-39
(2) Detaching and refitting the transfer belt unit................................................................... 1-5-41
(3) Detaching and reffiting the transfer roller ....................................................................... 1-5-43
1-5-6 Fuser section ....................................................................................................................... 1-5-45
(1) Detaching and reffiting the fuser unit.............................................................................. 1-5-45
(2) Detaching and reffiting Fuser IH unit .............................................................................. 1-5-47
1-5-7 PWBs................................................................................................................................... 1-5-49
(1) Detaching and refitting the main PWB............................................................................ 1-5-49
(2) Detaching and refitting the engine PWB......................................................................... 1-5-54
(3) Detaching and refitting the power source PWB.............................................................. 1-5-56
(4) Detaching and refitting the high voltage PWB 1 ............................................................. 1-5-59
(5) Detaching and refitting the high voltage PWB 2 ............................................................. 1-5-60
(6) Detaching and refitting the operation PWB .................................................................... 1-5-61
(7) Detaching and refitting the fuser IH PWB....................................................................... 1-5-65
2LK/2LN/2LM/2LC
1-5-8 Drive section ........................................................................................................................ 1-5-70

(1) Detaching and refitting the drum drive unit K and the drum drive unit MCY................... 1-5-70
(2) Detaching and refitting the main drive unit ..................................................................... 1-5-73
(3) Detaching and refitting the fuser drive unit, transfer drive unit and feed drive unit......... 1-5-74
(4) Detaching and refitting the lift motor 1 and 2.................................................................. 1-5-80
1-5-9 Others .................................................................................................................................. 1-5-81
(1) Detaching the eject filter ................................................................................................. 1-5-81
(2) Detaching and refitting the toner filter............................................................................. 1-5-82
(3) Detaching and refitting the fan filter................................................................................ 1-5-83
(4) Detaching and refitting the transfer belt filter.................................................................. 1-5-84
(5) Detaching and refitting the DU filter................................................................................ 1-5-85
(6) Detaching and refitting the left filter ................................................................................ 1-5-86
(7) Detaching and refitting the hard disk unit ....................................................................... 1-5-87
(8) Direction of installing the principal fan motors ................................................................ 1-5-89
1-6 Requirements on PWB Replacement

1-6-1 Upgrading the firmware ......................................................................................................... 1-6-1
1-6-2 Remarks on main PWB replacement..................................................................................... 1-6-2
1-6-3 Remarks on engine PWB replacement ................................................................................. 1-6-4
2-1 Mechanical Construction

2-1-1 Paper feed/conveying section ............................................................................................... 2-1-1
(1) Cassette paper feed section............................................................................................. 2-1-1
(2) MP tray paper feed section............................................................................................... 2-1-3
(3) Paper conveying section .................................................................................................. 2-1-5
2-1-2 Drum section ......................................................................................................................... 2-1-8
2-1-3 Developer section ................................................................................................................ 2-1-10
2-1-4 Optical section ..................................................................................................................... 2-1-12
(1) Image scanner section ................................................................................................... 2-1-12
(2) Laser scanner section .................................................................................................... 2-1-14
2-1-5 Transfer/Separation section ................................................................................................ 2-1-16
(1) Intermediate transfer unit section ................................................................................... 2-1-16
(2) Secondary transfer roller section.................................................................................... 2-1-18
2-1-6 Fuser section ....................................................................................................................... 2-1-20
2-1-7 Eject/Feedshift section ........................................................................................................ 2-1-22
2-1-8 Duplex conveying section .................................................................................................... 2-1-24
2-2 Electrical Parts Layout

2-2-1 Electrical parts layout ............................................................................................................ 2-2-1
(1) PWBs................................................................................................................................ 2-2-1
(2) Switches and sensors....................................................................................................... 2-2-4
(3) Motors............................................................................................................................... 2-2-6
(4) Fan motors ....................................................................................................................... 2-2-8
(5) Others............................................................................................................................. 2-2-10
2-3 Operation of the PWBs

2-3-1 Main PWB.............................................................................................................................. 2-3-1
2-3-2 Engine PWB ........................................................................................................................ 2-3-12
2-3-3 Power source PWB ............................................................................................................. 2-3-38
2-3-4 ISC PWB ............................................................................................................................. 2-3-46
2-3-5 Operation PWB 1................................................................................................................. 2-3-51
2-3-6 Front PWB ........................................................................................................................... 2-3-56
2-3-7 Feed PWB 1 ........................................................................................................................ 2-3-65
2LK/2LN/2LM/2LC
2-3-8 Feed PWB 2 ........................................................................................................................ 2-3-75

2-3-9 Relay PWB .......................................................................................................................... 2-3-81
2-3-10 Motor control PWB .............................................................................................................. 2-3-87
2-3-11 LSU relay PWB.................................................................................................................... 2-3-91
2-4 Appendixes
2-4-1 Appendixes ............................................................................................................................ 2-4-1
(1) Maintenance kits............................................................................................................... 2-4-1
(2) Repetitive defects gauge .................................................................................................. 2-4-3
(3) Firmware environment commands ................................................................................... 2-4-4
(4) Chart of image adjustment procedures .......................................................................... 2-4-11
(5) Wiring diagram ............................................................................................................... 2-4-13
INSTALLATION GUIDE
DOCUMENT PROCESSOR
PAPER FEEDER
LARGE CAPACITY FEEDER
1000-SHEETS FINISHER
ATTACHMENT KIT
HOLE PUNCH UNIT
FAX System
2LK/2LN/2LM/2LC
1-1-1 Specifications
1-1 Specifications
Machine
Specifications
Item
30 ppm 35 ppm 45 ppm 55 ppm
Type Desktop
Printing method Electrophotography by semiconductor laser, tandem drum system
Originals Sheet, Book, 3-dimensional objects (maximum original size: A3/Ledger)
Original feed system Fixed
Cassette 60 to 220 g/m2 60 to 256 g/m2
Paper weight
MP tray 60 to 300 g/m2 60 to 300 g/m2
Plain, Rough, Vellum, Recycled, Preprinted, Bond, Color (Colour),
Cassette Prepunched, Letterhead, Thick, High Quality, Custom 1 to 8
(Duplex: Same as simplex)
Paper type
Plain, Transparency (OHP film), Rough, Vellum, Labels, Recycled,
MP tray Preprinted, Bond, Cardstock, Color (Colour), Prepunched, Letterhead,
Thick, Coated, Envelope, High Quality, Custom 1 to 8
A3, B4, A4, A4R, B5, B5R, A5R, Ledger, Legal, Letter, LetterR, Statement,
Cassette
Oficio II, 12 × 18", Folio, 8K, 16K, 16KR
A3, B4, A4, A4R, B5, ISO B5, B5R, A5R, B6R, A6R, Return postcard,
Paper size Postcards, Envelope DL, Envelope C5, Envelope C4, Envelope #10
(Commercial #10), Envelope #9 (Commercial #9), Envelope #6
MP tray
(Commercial #6 3/4), Envelope Monarch, Youkei 2, Youkei 4, Ledger,
Legal, Letter, LetterR, ExecutiveR, Statement, Oficio II, 12 × 18", Folio,
8K, 16K, 16KR, Custom
Manual mode : 25 to 400%, 1% increments
Zoom level
Auto mode : Preset Zoom
A4 : 30 ppm A4 : 35 ppm A4 : 45 ppm A4 : 55 ppm
Letter : 30 ppm Letter : 35 ppm Letter : 45 ppm Letter : 55 ppm
A4R : 21 ppm A4R : 24 ppm A4R : 24 ppm A4R : 24 ppm
LetterR : 21 ppm LetterR : 24 ppm LetterR : 24 ppm LetterR : 24 ppm
B/W A3 : 15 ppm A3 : 17 ppm A3 : 22 ppm A3 : 27 ppm
Ledger : 15 ppm Ledger : 17 ppm Ledger : 22 ppm Ledger : 27 ppm
B4 : 18 ppm B4 : 21 ppm B4 : 27 ppm B4 : 33 ppm
Legal : 18 ppm Legal : 21 ppm Legal : 21 ppm Legal : 21 ppm
Copying B5 : 30 ppm B5 : 35 ppm B5 : 45 ppm B5 : 55 ppm
speed A4 : 30 ppm A4 : 35 ppm A4 : 45 ppm A4 : 50 ppm
Letter : 30 ppm Letter : 35 ppm Letter : 45 ppm Letter : 50 ppm
A4R : 21 ppm A4R : 24 ppm A4R : 24 ppm A4R : 24 ppm
LetterR : 21 ppm LetterR : 24 ppm LetterR : 24 ppm LetterR : 24 ppm
Color A3 : 15 ppm A3 : 17 ppm A3 : 22 ppm A3 : 25 ppm
Ledger : 15 ppm Ledger : 17 ppm Ledger : 22 ppm Ledger : 25 ppm
Legal : 18 ppm Legal : 21 ppm Legal : 21 ppm Legal : 21 ppm
1-1-1
2LK/2LN/2LM/2LC
Specifications
Item
First copy 6.1 s or less 5.7 s or less 4.5 s or less 4.1 s or less
B/W
time
(A4, feed from 8.0 s or less 7.3 s or less 5.8 s or less 5.4 s or less
cassette) Color
Warm-up Power on 25 s or less 25 s or less 30 s or less 30 s or less

time 20 s or less
Low Power 15 s or less 15 s or less 20 s or less
(22 °C/71.6
°F, 60% RH) Sleep 20 s or less 20 s or less 30 s or less 30 s or less
550 sheets (64 g/m2)

Cassette
Paper 500 sheets (80 g/m2)
capacity 100 sheets (80 g/m2, A4/Letter or less)
MP tray
50 sheets (80 g/m2, more than Letter/A4)
Top tray 250 sheets (80 g/m2)
with inner 30 sheets (80 g/m2)
Output tray
job separator
capacity
with right 100 sheets (80 g/m2)
job separator
Continuous copying 1 to 999 sheets
Light source LED
Scanning system Flat bed scanning by CCD image sensor
Photoconductor a-Si (drum diameter 30 mm)
Image write system Semiconductor laser
Charging system Charger roller
Touch down developing system
Developing system Developer: 2-component
Toner replenishing: Automatic from the toner container
Primary: Transfer belt
Transfer system
Secondary: Transfer roller
Separation system Small diameter separation, Separation electrode
Drum: Counter blade, Cleaning roller
Cleaning system
Transfer belt: Fur brush
Charge erasing system Exposure by cleaning lamp (LED)
Belt fusing
Fusing system Heat source: IH
Abnormally high temperature protection devices: thermostat
CPU PowerPC 750CL/600 MHz PowerPC 750GL/800 MHz
Main Standard 2048 MB

memory Maximum 2048 MB
Hard Disk 160 GB or more 320 GB (160 GB x 2) or more
1-1-2
2LK/2LN/2LM/2LC
Specifications
Item
USB Interface Connector: 1 (USB Hi-Speed)
Standard USB Port: 2 (Full-Speed USB)
Interface Network interface: 1 (10 BASE-T/100 BASE-TX/1000 BASE-T)
Fax slot: 2
Option
Network interface: 1 (10 BASE-T/100 BASE-TX/1000 BASE-T)
Resolution 600 × 600 dpi
Temperature 10 to 32.5 °C/50 to 90.5 °F
Operating Humidity 15 to 80% RH

environment Altitude 2,500 m/8,202 ft or less
Brightness 1,500 lux or less
machine 668 × 767 × 747 mm
Dimensions only 26 5/16 × 30 3/16 × 29 3/8”
(W × D × H) with paper 668 × 767 × 1053 mm
feeder 26 5/16 × 30 3/16 × 41 7/16”
977 × 767 mm (using MP tray)
Space required (W × D)
38 7/16 × 30 3/16” (using MP tray)
Weight 140 kg / 308.6 lb (with toner container)
120 V AC, 60 Hz, more than 12 A
Power source
220 - 240 V AC, 50/60 Hz, more than 7.2 A
Document processor, Original cover, Paper feeder, Large capacity feeder,
Side feeder, SMT paper feeder*, Side paper feeder*, Side large capacity
feeder*, 1000-sheet finisher, 4000-sheet finisher, Center-folding unit,
Options Mailbox, Punch unit, Inner job separator, Right job separator, Key counter,
Key card, Fax kit, Expansion memory, Internet fax kit (A), Data security kit,
Printed document guard kit and document table
*: 45 ppm/55 ppm model only
1-1-3
2LK/2LN/2LM/2LC
Printer
Specifications
Item
Printing speed Same as copying speed.
7.3 s or less 6.2 s or less 5.4 s or less 4.9 s or less
First print time B/W
(A4, feed from
9.5 s or less 7.8 s or less 6.6 s or less 6.2 s or less
cassette) Color
Resolution 600 x 600 dpi

Windows 2000 (Service Pack 2 or later), Windows XP,
Operating system Windows Server 2003, Windows Vista, Windows 7, Windows Server 2008,
Apple Macintosh OS 10.x
USB interface connector: 1 (USB Hi-speed)
Interface
Network interface: 1 (10BASE-T/100BASE-TX/1000BASE-T)
Page description language PRESCRIBE
1-1-4
2LK/2LN/2LM/2LC
Scanner
Specifications
Item
CPU: 600 Mhz or higher
System requirements
RAM: 128 MB or more
Resolution 600 dpi, 400 dpi, 300 dpi, 200 dpi, 200 ×100 dpi, 200 × 400 dpi
TIFF (MMR/JPEG compression), JPEG, XPS,
File format
PDF (MMR/JPEG compression), PDF (high compression)
Scanning speed B/W : 70 images/min B/W : 80 images/min

(A4 landscape, Simplex Color: 70 images/min Color: 80 images/min
300 dpi,
Image quality: B/W : 100 images/min B/W : 140 images/min
Text/Photo orig- Duplex Color: 80 images/min Color: 110 images/min
inal)
Interface Ethernet (10 BASE-T/100 BASE-TX/1000 BASE-T)

Network protocol TCP/IP
PC transmission
SMB Scan to SMB
FTP Scan to FTP, FTP over SSL
Transmission system E-mail transmission
SNTP Scan to E-mail
TWAIN scan*1
WIA scan*2
*1 Available operating system: Windows 2000 (Service Pack 2 or later), Windows XP, Windows Server 2003,
Windows Vista, Windows 7, Windows Server 2008
*2 Available operating system: Windows Vista, Windows 7, Windows Server 2008
NOTE: These specifications are subject to change without notice.
1-1-5
2LK/2LN/2LM/2LC
1-1-2 Parts names

(1) Machine
1
7
17 8
18 2
9
19 10
3
20 4
5
6
16
11 12 13 14 15
Figure 1-1-1
1. Original size indicator plate 11. Handles

2. Slit glass 12. Release button
3. Toner container K 13. Waste toner box
4. Toner container M 14. Waste toner tray
5. Toner container C 15. Front cover
6. Toner container Y 16. Toner container release lever
7. Platen (Contact glass) 17. Network interface connector
8. Clip holder 18. USB port
9. Operation panel 19. USB interface connector
10. Indicators 20. Option interface
1-1-6
2LK/2LN/2LM/2LC
23
28 26 27 28 21 22 24
30 40
31
32
33
34
29 35
36
37
38
25 39
Figure 1-1-2
21. Inner tray 31. Paper conveying unit lever

22. Document processor (option) 32. Duplex cover lever
23. Original cover 33. Duplex cover
24. USB port 34. MP paper width guide
25. Cassettes 35. MP support Tray
26. Paper length guide 36. MP (Multi-Purpose) tray
27. Guide lock lever 37. Paper conveying cover lever
28. Paper width guide 38. Paper conveying cover
29. Paper width adjusting tab 39. Handle
30. Paper conveying unit 40. Main power switch
1-1-7
2LK/2LN/2LM/2LC
(2) Option
3
13
2 6
10
11
12 5, 9
Figure 1-1-3
1. Machine 7. SMT paper feeder

2. Document processor 8. Side paper feeder
(dual scan DP) 9. Side large capacity feeder
3. Document processor 10. 1000-sheet finisher
(reversed DP) 11. 4000-sheet finisher
4. Paper feeder 12. Center folding unit
5. Large capacity feeder 13. Mailbox
6. Side feeder
1-1-8
2LK/2LN/2LM/2LC
(3) Operation panel
1 2 3 4 5 6 7 8 9 10 11 12 13
14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29
Figure 1-1-4
1. Program key 11. Power key 21. Memory indicator

2. Status/Job cancel key 12. Counter key 22. Numeric keys
3. Copy key 13. Main power indicator 23. Enter key
4. Accessibility display key 14. Application key 24. Attention indicator
5. Help key 15. Document box key 25. Start key
6. Auto color key 16. Send key 26. Stop key
7. Quick no. search key 17. FAX key* 27. Interrupt key
8. Clear key 18. Full color key 28. Authentication/Logout key
9. Reset key 19. Processing indicator 29. Energy saver key
10. System menu key 20. Black and White key
*: Option
1-1-9
2LK/2LN/2LM/2LC
1-1-3 Machine cross section
18
14
17
13 9 12 8 11 7 10 6
19
15
16
Paper Path
Figure 1-1-5
1. Cassette paper feed section 8. Drum unit C 15. Primary transfer section
2. MP tray paper feed section 9. Drum unit Y 16. Secondary transfer/Separa-
3. Paper conveying section 10. Developer unit K tion sections
4. Optical section 11. Developer unit M 17. Fuser section
5. Laser scanner unit 12. Developer unit C 18. Eject/Feed shift sections
6. Drum unit K 13. Developer unit Y 19. Duplex section
7. Drum unit M 14. Toner container section
1-1-10
2LK/2LN/2LM/2LC
1-2-1 Installation environment

1-2 Installation
1. Temperature: 10 to 32.5°C/50 to 90.5°F

2. Humidity: 15 to 80% RH
3. Power supply: 120 V AC, 12.0 A
220 - 240 V AC, 7.2 A
4. Power source frequency: 50 Hz ± 2%/60 Hz ± 2%
5. Installation location
Avoid direct sunlight or bright lighting. Ensure that the photoconductor will not be exposed to direct sun-
light or other strong light when removing paper jams.
Avoid locations subject to high temperature and high humidity or low temperature and low humidity; an
abrupt change in the environmental temperature; and cool or hot, direct air.
Avoid places subject to dust and vibrations.
Choose a surface capable of supporting the weight of the machine.
Place the machine on a level surface (maximum allowance inclination: 1°).
Avoid air-borne substances that may adversely affect the machine or degrade the photoconductor, such
as mercury, acidic of alkaline vapors, inorganic gasses, NOx, SOx gases and chlorine-based organic sol-
vents.
Select a well-ventilated location.
6. Allow sufficient access for proper operation and maintenance of the machine.
Machine front : 100 cm/39 3/8"
Machine rear : 10 cm/ 3 15/16"
Machine right : 35 cm/13 3/4"
Machine left : 30 cm/11 13/16"
Machine top : 40 cm/15 3/4"
10cm/3 15/16"
Top 40cm/15 3/4"
30cm/11 13/16" 35cm/13 3/4"
100cm/39 3/8"
Figure 1-2-1
1-2-1
2LK/2LN/2LM/2LC
1-2-2 Unpacking and installation

(1) Installation procedure
Start
Unpacking Installing the waste toner box
Removing the eject spacer Replacing operation panel sheet

(230 V specifications only)
Removing the tapes

Install the original platen or DP (option)
Installing the paper feeder (option)

Install other optional devices
Release the lock of the scanner mirror frame

Install the cassette heater (option)
Release of lift plate stopper

Connect the power cord
Loading paper
Adjusting the image
Installing the toner containers

Completion of the machine installation.
Unlocking the developer waste
1-2-2
2LK/2LN/2LM/2LC
Moving the machine

When moving the machine, pull out three carrying handles, and move with carrying handles and the hand-
hold.
Carrying
handle Handhold
Carrying
handle Carrying
handle
Figure 1-2-2
1-2-3
2LK/2LN/2LM/2LC
Unpacking
12 18
22
17 22
22
15
19,20
21
16
14
22
22
13 22
10
4
8 7
11
3
9 5
Figure 1-2-3
1. Machine 12. Machine cover

2. Outer case 13. Document tray
3. Inner case 14. Power cord
4. Top pad 15. Plastic bag
5. Skid 16. Operation guide
6. Bottom sheet 17. Paper size plate
7. Bottom pad 18. Paper media plate
8. Bottom front left pad 19. Eject spacer
9. Bottom front right pad 20. Waste toner box
10. Bottom rear left pad 21. Barcode label
11. Bottom rear right pad 22. Hinge joints
Place the machine on a level surface.
1-2-4
2LK/2LN/2LM/2LC
Removing the eject spacer
1. Remove the eject spacer and silica gel

from the eject section.
Silica gel
Eject spacer
Figure 1-2-4
Removing the tapes
1. Remove three tapes and then remove Tape A3 papers

the A3 paper.
2. Remove two tapes and then remove the Tape
A4 paper.
Tape
Tape
Tape
A4 paper
Figure 1-2-5
1-2-5
2LK/2LN/2LM/2LC
3. Remove six tapes.

Tape Tape
Tape
Tape
Tapes
Figure 1-2-6
Installing the paper feeder (option)
1. Install the optional paper feeder or large

capacity feeder as necessary.
2. Verify levelness at the four corners of
the contact glass using a level gauge,
and adjust the level bolts at the bottom
of the machine to optimize levelness.
1-2-6
2LK/2LN/2LM/2LC
Release the lock of the scanner mirror frame
1. Remove the scanner lock cover.

2. Mount the scanner lock cover in the
reverse manner to restore in the original
location.
Scanner lock cover
[Locked] [Released]
Figure 1-2-7
1-2-7
2LK/2LN/2LM/2LC
Release of lift plate stopper
1. Pull cassette 1 and 2 out.

2. Remove the lift plate stopper from each
cassette and attach it to the storage
location.
When moving the machine, attach the
lift plate in original position. Lift plate
stopper
Cassette
Figure 1-2-8
Loading paper
1. Squeeze the ends of the bottom of the Paper length guide

paper length guide and move the guide
to fit the length of the paper.
Figure 1-2-9
1-2-8
2LK/2LN/2LM/2LC
2. Press the guide lock lever to release

the lock.
3. Grasp the paper width adjusting tab and
move the paper width guides to fit the
paper.
Guide lock lever
Paper width paper width guides

adjusting tab
Figure 1-2-10
4. Align the paper flush against the right Paper

side of the cassette.
*: Before loading the paper, be sure that it is
not curled or folded.
*: Ensure that the loaded paper does not
exceed the level indicated.
Figure 1-2-11
1-2-9
2LK/2LN/2LM/2LC
5. Press the guide lock lever to lock.
Guide lock lever
Figure 1-2-12
6. Fold the paper size plate and the paper Paper media plate
media plate in two and insert.
7. Gently push the cassette back in. Paper size plate
Figure 1-2-13
1-2-10
2LK/2LN/2LM/2LC
Installing the toner containers
1. Open the front cover.

2. Hold the toner container vertically and
hit the upper part about 3 times. Invert
the toner container so that the other end
is up, and hit in the same way.
3. Hold the toner container horizontally
and shake from side to side about 3
times.
Toner container
Toner container
Figure 1-2-14
4. Install four color toner containers.

5. Turn down the toner container release
levers to lock the four color toner con-
tainers.
K
M
C
Y
Toner container
Toner container
Release lever
Figure 1-2-15
1-2-11
2LK/2LN/2LM/2LC
Unlocking the developer waste
1. Press the stopper in four positions and

rotate.
[State of lock] [State of release]

2
Stopper Stopper
Figure 1-2-16
2. Remove a screw and slide the lever

right wards.
3. Fix the lever using the screw previously
removed at the right screw hole and
unlock the developer waste.
*: If the machine is moved after installation,
lock the developer waste.
*: Failure to perform locking could result in
leakage of developing power.
[Locked] [Released]
3
2
1
Screw
Lever Screw Lever
Figure 1-2-17
1-2-12
2LK/2LN/2LM/2LC
Installing the waste toner box
1. Push the release button and pull out the

waste toner tray.
Waste toner tray
2. Open the lid and install the waste toner
box.
3. Push the waste toner tray back in.
*: The waste toner tray cannot be inserted
in unless the developer waste lock is
released.
4. Close the front cover.
2
1
Release button
Lid
Waste toner box
Figure 1-2-18
1-2-13
2LK/2LN/2LM/2LC
Replacing operation panel sheet (230 V specifications only)
1. Insert a flat-head screwdriver and slide

the operation panel covers A and B to
remove them.
Operation panel
cover B
Operation panel
cover A
Figure 1-2-19
2. Remove the clear panel.

Clear panel
Figure 1-2-20
1-2-14
2LK/2LN/2LM/2LC
3. Remove the operation panel sheet. Operation

4. Replace the operation panel sheet of panel sheet
the corresponding language.
5. Refit the clear panel.
6. Refit the operation panel covers A and
B.
Figure 1-2-21
Install the original platen or DP (option)
1. Install optional original platen or DP.
Install other optional devices
1. Install the optional devices (job separa-

tor, document finisher and/or fax kit
etc.) as necessary.
Install the cassette heater (option)
1. Install the optional cassette heater as

necessary.
Connect the power cord
1. Connect the power cord to the power

cord connector on rear lower of the
machine.
2. Connect the power plug to the wall out-
let.
1-2-15
2LK/2LN/2LM/2LC
Adjusting the image
1. Turn the main power switch on.
2. Check the messages on the operation panel

After completion of warming up, in case to display "Warning for high temperature. Adjust the room tem-
perature." on the operation panel, follow the step 3. (Performing Drum Refresh)
In case to display “Warning for low temperature. Adjust the room temperature.” on the operation panel,
install the machine in the other location this message won’t be shown.
Installing the machine in a low temperature environment could cause image quality problems.
In case to have no display, follow the step 4. (Performing Color adjustment)
3. Performing drum refresh (see the operation guide)

Press the System menu key.
Press [Adjustment/Maintenance] and then [Next] of [Drum Refresh].
Press [Execute] to perform drum refresh. When completed, press [OK].
4. Performing Color adjustment (see the operation guide)

Press [Adjustment/Maintenance] and then [Next] of [Calibration].
Press [Execute] to perform Color Calibration. When completed, press [OK].
5. Performing color registration (see the operation guide)

Press [Adjustment/Maintenance] and then [Next] of [Color Registration].
Perform adjustments automatically or manually.
Auto correction
Press [Next] in [Auto]. Press [Start]. A chart is printed.
Set the output chart for adjustment as the original.
Press [Start] to perform Color registration. When completed, press [OK].
Manual correction
Press [Next] in [Manual]. Press [Print] of [Chart]. A chart is printed.
Find the location on each chart where 2 lines most closely match.
Press [Next] of [Registration] and [Change].
Enter the registration values for each chart.
Press [Start] to perform Color registration. When completed, press [OK].
6. Adjusting the halftone automatically (see page 1-3-151)

Load the cassette with multiple sheets of A4 or Letter paper.
Enter the maintenance mode by entering 10871087 using the numeric keys.
Enter 410 using the numeric keys and press the start key.
Press [Normal Mode] and then press the start key. A test patterns 1, 2 and 3 are outputted.
Place the output test pattern 1 as the original.
Place approximately 20 sheets of white paper on the test pattern 1 and set them.
Press the start key. Adjustment is made.
[Finish] is displayed in [Phase] when normally completed.
Press the stop key twice to exit.
1-2-16
2LK/2LN/2LM/2LC
7. Make test copies.

If image quality is unsatisfactory after test copying, execute Color Calibration, then retry U410-Adjusting
the halftone automatically.
8. Setting the delivery date (see page 1-3-137)

Enter 278 using the numeric keys and press the start key.
Select [Today].
Press the start key. The delivery date is set.
Press the stop key to exit.
9. Output status report

Use the numeric keys to enter 000 and press the start key.
Select [Maintenance].
Press the start key. A status report is output.
Press the stop key to exit.
10. Turn the main power switch off and on. Allow more than 5 seconds between Off and On.
Completion of the machine installation
1-2-17
2LK/2LN/2LM/2LC
(2) Setting initial copy modes

Factory settings are as follows:
Maintenance
Contents Factory setting
item No.
U253 Switching between double and single counts DBL(A3/Ledger)
U260 Selecting the timing for copy counting Eject
U276 Setting the copy count mode Mode0
U284 Setting 2 color copy mode Off
U285 Setting service status page On
U323 Setting abnormal temperature and humidity warning On
U325 Setting the paper interval On/1
U326 Setting the black line cleaning indication On/8
U327 Setting the cassette heater control Off
U343 Switching between duplex/simplex copy mode Off
1-2-18
2LK/2LN/2LM/2LC
1-3-1 Maintenance mode

1-3 Maintenance Mode
The machine is equipped with a maintenance function which can be used to maintain and service the
machine.
(1) Executing a maintenance item
Start
Enter “10871087” using

Maintenance mode is entered.
the numeric keys.
Enter the maintenance item

number using the cursor up/down keys The maintenance item is selected.
or numeric keys.
Press the start key.
The selected maintenance item is run.
Press the stop key.
Yes Repeat the same

maintenance item?
No
Yes
Run another maintenance
item?
No
Enter 001 using the cursor
up/down keys or numeric keys Maintenance mode is exited.
and press the start key.
End
1-3-1
2LK/2LN/2LM/2LC
(2) Maintenance modes item list
Item Initial setting

Section Content of maintenance item
No. 30ppm 35ppm 45ppm 55ppm
General U000 Outputting an own-status report -
U001 Exiting the maintenance mode -
U002 Setting the factory default data -
U003 Setting the service telephone number -
U004 Setting the machine number -
U010 Setting the maintenance mode ID -
U019 Displaying the ROM version -
Initializa- U021 Memory initializing -
tion
U024 HDD formatting -
Drive, U030 Checking the operation of the motors -
paper feed
U031 Checking switches and sensors for paper con- -
and paper veying
conveying
system U032 Checking the operation of the clutches -
U033 Checking the operation of the solenoids -
U034 Adjusting the print start timing
LSU Out Top 0/0/0/0/0/0/0/0/0/0/0/0
LSU Out Left 0/0/0/0/0/0/0/0/0
LSU Out Top B/W 0/0/0/0/0/0
LSU Out Top 3/4 0/0/0/0/0/0
U035 Setting the printing area for folio paper 330/210
U037 Checking the operation of the fan motors -
U039 Adjusting the magnification 0/0
U051 Adjusting the deflection in the paper
Paper Loop Amount 0/0/0/0/0/0/0/0/0/0/0/0
Paper Loop Amount B/W 0/0/0/0/0/0
Paper Loop Amount 3/4 0/0/0/0/0/0
U052 Setting the fuser motor control
Set Loop Sensor -
Loop Sensor Control Off/On/On/On
Set Loop Sensor Valid On
1-3-2
2LK/2LN/2LM/2LC

Drive, U053 Setting the adjustment of the motor speed
paper feed
Moter1 0/0/0/0/0
and paper
conveying Moter2 0/0/0/0/0/0/0/0/0
system Moter3 0/0/0/0/0/0/0/0/0/0
Moter4 0/0
Moter5 0/0/0/0/0
Moter6 0/0/0/0/0/0/0/0/0
Moter1 Half 0/0/0/0/0
Moter2 Half 0/0/0/0/0/0/0
Moter3 Half 0/0/0/0/0/0/0
Moter1 3/4 0/0/0/0/0
Moter2 3/4 0/0/0/0/0/0/0/0/0
Moter3 3/4 0/0/0/0/0/0/0/0
U059 Setting fan mode
Fan Mode Mode2
Cooling Mode 0
Optical U061 Checking the operation of the exposure lamp -
U063 Adjusting the shading position 0
U065 Adjusting the scanner magnification 0/0
U066 Adjusting the scanner leading edge registration 0/0
U067 Adjusting the scanner center line 0/0
U068 Adjusting the scanning position for originals 0/0
from the DP
U070 Adjusting the DP magnification 0/0/0
U071 Adjusting the DP scanning timing 0/0/0/0/0/0
U072 Adjusting the DP center line 0/0/0
U073 Checking the scanner operation -
U074 Adjusting the DP input light luminosity 0
U087 Setting DP reading position modification opera- 125/125/125
tion
U089 Outputting a MIP-PG pattern -
U091 Setting the white line correction 112/112/112/75/0
1-3-3
2LK/2LN/2LM/2LC

Optical U093 Adjusting the exposure density gradient
Text 0/0/0/0
Mixed 0/0/0/0
Other 0/0/0/0
Fax Text 0/0
Fax Photo 0/0
U099 Adjusting original size detection 50/50/50/50/50/50/50/50/50/
49/49/49/150
High U100 Adjusting main high voltage
voltage Adj AC Bias -
Set AC Auto Adj On
Set DC Bias -
Adj DC Bias 0/0/0/0/0/0/0/0/0
Set Low Temp 1
Set Charger Freq 1429 1333
Chk Current -
U101 Setting the voltage for the primary transfer
Normal Full 116 123 132
Normal Half - 109 115
Normal 3/4 158
Add Color 3/3/5
Add Color 2nd 0/0/0/-15
Surround Correct On
U106 Setting the voltage for the secondary transfer
Light/Normal1 153 140 153 166
Normal2/3 153 140 153 166
Heavy1 153 140 153 166
Heavy2-5 153 140 153 166
OHP 153 140 153 166
Bias 42/42/42/42/42/42/42
U107 Setting the transfer cleaning voltage
Belt(A) 86 74 86 97
Belt(B) 86 74 86 97
1-3-4
2LK/2LN/2LM/2LC

High U108 Setting separation shift bias
voltage
Output 21/21/21/21/0/21
Output 3/4 43/43/43/43
Output B/W 43/43/43/43
Timing -
U109 Checking the drum type -
U110 Checking the drum count -
U111 Checking the drum drive time -
U117 Checking the drum number -
U118 Displaying the drum history -
U119 Setting the drum -
U122 Checking the transfer belt unit number -
U123 Displaying the transfer belt unit history -
U124 Checking/clearing the transfer drive time -
U127 Checking/clearing the transfer count -
U128 Setting transfer high-voltage timing -54/-54/10
Developer U130 Toner installation -
U131 Adjusting the toner sensor control voltage -
U132 Replenishing toner forcibly
Manual 116/116/116/116
Auto -
Mode Auto
U135 Checking toner motor operation -
U136 Setting toner near end detection 3/3
U139 Displaying the temperature and humidity outside -
the machine
U140 Displaying developer bias
Sleeve DC 62/62/62/62/70 70/70/70/70/70
Sleeve AC 159/159/159/ 155/155/155/
159/155 155/155
Mag DC 130/130/130/ 155/155/155/
130/155 155/155
Mag AC 101/101/101/ 178/178/178/
101/178 178/178
Sleeve Freq 5276/5344/5276/5276
Sleeve Duty 37/68 68/68
Mag Duty 63/43 43/43
1-3-5
2LK/2LN/2LM/2LC

Developer U140 Calibration -
Magnification 0/0/0/0
Type Mode1
U148 Setting drum refresh mode 2
U150 Checking sensors for toner -
U156 Setting the toner replenishment level -
U157 Checking the developer drive time -
U158 Checking the developer count -
Fuser U161 Setting the fuser control temperature
Warm Up 165/1/90/175/165/150/160/50
Print
U163 Resetting the fuser problem data -
U167 Checking/clearing the fuser count -
U168 Checking/clearing the fuser drive time -
U169 Checking/setting the fuser power source -
U199 Displaying fuser heater temperature -
Operation U200 Turning all LEDs on -
panel and
U201 Initializing the touch panel -
support
equipment U202 Setting the KMAS host monitoring system -
U203 Checking DP operation -
U204 Setting the presence or absence of a key card or
key counter
Device Off
Message Coin Vender
U206 Setting the presence or absence of a coin
vender
On/Off Config Off
No Coin Action Off
Price 10/10/10/10/100/50/30/50/
100/50/30/50/100/50/30/50
U207 Checking the operation panel keys -
U208 Setting the paper size for the side feeder Letter (Inch)/A4 (Metric)
U211 Setting the presence or absence of the job sep- Off
arator
U221 Setting the USB host lock function Off
U222 Setting the IC card type Other
1-3-6
2LK/2LN/2LM/2LC

Operation U223 Operation panel lock Unlock
panel and
U224 Panel sheet extension -
support
equipment U234 Setting punch destination Inch (Inch)/Europe Metric (Metric)
U237 Setting finisher stack quantity 0/0
U240 Checking the operation of the finisher -
U241 Checking the operation of the switches of the -
finisher
U243 Checking the operation of the DP motors -
U244 Checking the DP switches -
U245 Checking messages -
U246 Setting the finisher
Finisher 0/0/0/0/0/0/0/0
Booklet 0/0/0/0/0/0/0/0/0
U247 Setting the paper feed device -
Mode U250 Checking/clearing the maintenance cycle -
setting
U251 Checking/clearing the maintenance counter -
U252 Setting the destination -
U253 Switching between double and single counts DBL(A3/Ledger)
U260 Selecting the timing for copy counting Eject
U265 Setting OEM purchaser code -
U271 Setting the page count -
U276 Setting the copy count mode Mode1
U278 Setting the delivery date -
U284 Setting 2 color copy mode Off
U285 Setting service status page On
U323 Setting abnormal temperature and humidity On
warning
U325 Setting the paper interval On/1
U326 Setting the black line cleaning indication On/8
U327 Setting the cassette heater control Off
U332 Setting the size conversion factor
Mode 0
Coverage(L) 1.0
Coverage(M) 1.0
U340 Setting the applied mode 0/0
1-3-7
2LK/2LN/2LM/2LC

Mode U341 Specific paper feed location setting for printing -
setting function
U343 Switching between duplex/simplex copy mode Off
U345 Setting the value for maintenance due indication 0
Image U402 Adjusting margins of image printing 4.0/3.0/3.0/3.9
processing U403 Adjusting margins for scanning an original on
2.0/2.0/2.0/2.0
the contact glass
U404 Adjusting margins for scanning an original from 2.0/2.0/2.0/2.0/2.0/2.0/2.0/2.0
the DP
U407 Adjusting the leading edge registration for mem- 0
ory image printing
U410 Adjusting the halftone automatically Table1
U411 Adjusting the scanner automatically -
U412 Adjusting the uneven density -
U415 Adjusting the print position automatically -
U425 Setting the target -
U429 Setting the offset for the color balance 0/0/0/0
U464 Setting the ID correction operation
Permission On
Time Interval 480
Mode Normal
On/Sleep Out On
AP/NE On
Leaving Time 60
Driving Time 600
Timing 1800
Target Value 500/500/500/10/300/300/300/300
Print Rate(B/W) 50
Calib -
U465 Data reference for ID correction -
U467 Setting the color registration adjustment
Color Regist On
Belt Speed On
Timing 10
U468 Checking the color registration data -
U469 Adjusting the color registration -
1-3-8
2LK/2LN/2LM/2LC

Image U474 Checking LSU cleaning operation 1000
processing
U485 Setting the image processing mode 1/0
U486 Setting color/black and white operation mode Mode2
Others U901 Checking copy counts by paper feed locations -
U903 Checking/clearing the paper jam counts -
U904 Checking/clearing the call for service counts -
U905 Checking counts by optional devices -
U906 Resetting partial operation control -
U908 Checking the total counter value -
U910 Clearing the print coverage data -
U911 Checking copy counts by paper sizes -
U917 Setting backup data reading/writing -
U920 Checking the copy counts -
U927 Clearing the all copy counts and machine life -
counts (one time only)
U928 Checking machine life counts -
U930 Checking/clearing the charger roller count -
U942 Setting of deflection for feeding from DP 0/0
U952 Maintenance mode workflow -
U964 Checking of log -
U969 Checking of toner area code -
U977 Data capture mode -
U984 Checking the developer unit number -
U985 Displaying the developer unit history -
U989 HDD Scandisk -
U990 Checking the time for the exposure lamp to light -
U991 Checking the scanner operation count -
1-3-9
2LK/2LN/2LM/2LC
(3) Contents of the maintenance mode items

Item No. Description
U000 Outputting an own-status report
Description
Outputs lists of the current settings of the maintenance items, and paper jam and service call
occurrences. Outputs the event log or service status page. Also sends output data to the USB
memory.
Purpose
To check the current setting of the maintenance items, or paper jam or service call occurrences.
Before initializing or replacing the backup RAM, output a list of the current settings of the mainte-
nance items to reenter the settings after initialization or replacement.
Method
1. Press the start key.
2. Select the item to be output using the cursor up/down keys.
Display Output list
Maintenance List of the current settings of the maintenance modes
User Status Outputs the user status page
Service Status Outputs the service status page
Event Outputs the event log
Network Status Outputs the network status page
All Outputs the all reports
3. Press the start key. A list is output.

4. Press the start key. The interrupt print mode is entered and a list is output.
When A4/Letter paper is available, a report of this size is output. If not, specify the paper feed
location.
The output status is displayed.
Display Description
Ready List of the current settings of the maintenance modes
Active Outputs the user status page
Complete Outputs the service status page
Error Outputs the event log
1-3-10
2LK/2LN/2LM/2LC

U000 Method: Send to the USB memory
1. Press the power key on the operation panel, and after verifying the main power indicator has
gone off, switch off the main power switch.
2. Insert USB memory in USB memory slot.
4. Enter the maintenance item.
6. Select the item to be send.
7. Select [Text] or [HTML].
Display Output list
Print Outputs the report
USB (Text) Sends output data to the USB memory (text type)
USB (HTML) Sends output data to the USB memory (HTML type)

Output will be sent to the USB memory.
Completion
Press the stop key. The screen for selecting a maintenance item No. is displayed.
1-3-11
2LK/2LN/2LM/2LC

U000 Event log
Event Log
MFP (2) 27/Oct/2010 08:40
(3) (4) (5) (6)
(1) Firmware version 2LC_2000.000.000 2010.10.27 [XXXXXXXX] [XXXXXXXX] [XXXXXXXX] [XXXXXXXX]
(8) Paper Jam Log (12) Counter Log

# Count. Event Descriprions
16 9999999 0501.01.08.01.01
(f) J0000: 0 J0041: 1 (g) C0000: 0 (h) T00: 10
J0001: 1 J0042: 1 C0001: 1 T01: 20
15 8888888 4002.01.08.01.01
J0002: 11 J0043: 1 C0002: 2 T02: 30
14 7777777 0501.01.08.01.01
J0003: 222 J0044: 1 C0003: 3 T03: 40
13 6666666 4002.01.08.01.01
J0004: 1 J0045: 1 C0004: 4 T04: 50
12 5555555 0501.01.08.01.01
J0005: 1 J0046: 1 C0005: 5 T05: 999
11 4444444 4002.01.08.01.01
J0006: 1 J0047: 1 C0006: 6
10 3333333 0501.01.08.01.01
J0007: 1 J0048: 1 C0007: 7
9 2222222 4002.01.08.01.01
J0008: 1 J0049: 1 C0008: 8
8 1111111 0501.01.08.01.01
J0009: 1 J0050: 1 C0009: 9
7 999999 4002.01.08.01.01
J0010: 1 C0010: 10
6 888888 0501.01.08.01.01
J0012: 999 C0011: 11
5
4 0501.01.08.01.01
777777
666666
4002.01.08.01.01
0501.01.08.01.01
J0013: 1 C0012: 12
J0014: 1 C0013: 13
3 555555 (a) (b) (c) (d)
4002.01.08.01.01 (e)
J0015: 1 C0014: 14
2 444444 0501.01.08.01.01
J0016: 1 C0015: 15
1 1 4002.01.08.01.01
J0017: 1 C0016: 16
J0018: 1 C0017: 17
(9) Service Call Log J0019: 1 C0018: 18
# Count. Service Code J0020: 1 C0019: 19
8 1111111 01.6000 J0021: 1 C0020: 20
7 999999 01.2100 J0022: 1 C0021: 21
6 888888 01.4000 J0023: 1 C0022: 22
5 777777 01.6000 J0024: 1 C0023: 23
4 666666 01.2100 J0025: 1
3 555555 01.4000 J0026: 1
2 444444 01.6000 J0027: 1
1 1 01.2100 J0028: 1
J0029: 1
(10) Maintenance Log J0030: 1
# Count. Item J0031: 1
J0032: 1
Log Data Nothing... J0033: 1
J0034: 1
J0035: 1
(11) Unknown toner Log
J0036: 1
# Count. Item
J0037: 1
5 1111111 01.00
J0038: 1
4 999999 01.00
J0039: 1
3 888888 01.00
J0040: 1
2 777777 01.00
1 666666 01.00
(7) [XXXXXXXXXXXXXXXX]
Figure 1-3-1
Detail of event log

No. Items Description
(1) System version
(2) System date
(3) Engine soft version
(4) Engine boot version
1-3-12
2LK/2LN/2LM/2LC

U000 Detail of event log
(5) Controller BROM version
(6) Operation panel mask version
(7) Machine serial number
(8) Paper Jam # Count. Event
Log The total page count Log code (hexadeci-
Remembers 1 to 16 of
occurrence. If the occur- at the time of the mal, 5 categories)
rence of the previous paper jam.
paper jam is less than (a) Cause of a paper
16, all of the paper jams jam
are logged. When the (b) Paper source
occurrence excesseds (c) Paper size
16, the oldest occur- (d) Paper type
rence is removed. (e) Paper eject
(a) Cause of paper jam (Hexadecimal)
For details on the case of paper jam, refer to Paper Misfeed Detection.
(P.1-4-1)
(b) Detail of paper source (Hexadecimal)
00: MP tray
01: Cassette 1
02: Cassette 2
03: Cassette 3 (paper feeder/large capacity feeder)
04: Cassette 4 (paper feeder/large capacity feeder)
05: Cassette 5 (side feeder/SMT paper feeder)
06: Cassette 6 (side paper feeder/side large capacity feeder)
07: Cassette 7 (side paper feeder/side large capacity feeder)
08 to 09: Reserved
(c) Detail of paper size (Hexadecimal)

00: (Not specified) 0B: B4 22: Special 1
01: Monarch 0C: Ledger 23: Special 2
02: Business 0D: A5R 24: A3 wide
03: International DL 0E: A6 25: Ledger wide
04: International C5 0F: B6 26: Full bleed paper
05: Executive 10: Commercial #9 (12 x 8)
06: Letter-R 11: Commercial #6 27: 8K
86: Letter-E 12: ISO B5 28: 16K-R
07: Legal 13: Custom size A8: 16K-E
08: A4R 1E: C4 32: Statement-R
88: A4E 1F: Postcard B2: Statement-E
09: B5R 20: Reply-paid post- 33: Folio
89: B5E card 34: Western type 2
0A: A3 21: Oficio II 35: Western type 4
1-3-13
2LK/2LN/2LM/2LC

U000
(8) Paper Jam (d) Detail of paper type (Hexadecimal)
cont. Log 0A: Color 15: Custom 1
01: Plain
02: Transparency 0B: Prepunched 16: Custom 2
03: Preprinted 0C: Envelope 17: Custom 3
04: Labels 0D: Cardstock 18: Custom 4
05: Bond 0E: Coated 19: Custom 5
06: Recycled 0F: 2nd side 1A: Custom 6
07: Vellum 10: Media 16 1B: Custom 7
08: Rough 11: High quality 1C: Custom 8
09: Letterhead
(e) Detail of paper eject location (Hexadecimal)
01: Face down (FD)
02: Face up (FU)/1000-sheet finisher face up (FU)/
4000-sheet finisher left sub tray (FU)
03: 1000-sheet finisher face down (FD)
4000-sheet finisher main tray (FD)
05: Job separator tray
06: 4000-sheet finisher right sub tray (FU)
07: 4000-sheet finisher left sub tray (FD)
09: 4000-sheet finisher right sub tray (FD)
0A: Center-folding unit tray
0B: Mailbox tray 1 (FD)
0C: Mailbox tray 1 (FU)
15: Mailbox tray 2 (FD)
16: Mailbox tray 2 (FU)
1F: Mailbox tray 3 (FD)
2A: Mailbox tray 4 (FU)
3D: Mailbox tray 6 (FD)
3E: Mailbox tray 6 (FU)
04/0D/0E: Reserved
1-3-14
2LK/2LN/2LM/2LC

U000
(9) Service Call # Count. Service Code
Log The total page Self diagnostic error code
Remembers 1 to 8
of occurrence of self count at the time of (See page 1-4-27)
diagnostics error. If the self diagnostics
the occurrence of error. Example:
the previous diag- 01.6000
nostics error is less
than 8, all of the 01: Self diagnostic error
diagnostics errors 6000: Self diagnostic error
are logged. code number
(10) Maintenance # Count. Item

Log The total page Code of maintenance
Remembers 1 to 8
of occurrence of count at the time of replacing item
replacement. If the the replacement of (1 byte, 2 categories)
occurrence of the the toner container.
previous replace- First byte (Replacing item)
ment of toner con- 01: Toner container
tainer is less than 8, Second byte
all of the occur- (Type of replacing item)
rences of replace- 00: Black
ment are logged. 01: Cyan
02: Magenta
03: Yellow
First byte (Replacing item)

02: Maintenance kit
Second byte
(Type of replacing item)
01: MK-8305A/8505A
02: MK-8305B/8505B
03: MK-8305C/8505C
(11) Unknown # Count. Item

Toner Log
Remembers 1 to 5 The total page Unknown toner log code
of occurrence of count at the time of (1 byte, 2 categories)
unknown toner the toner empty
detection. If the error with using an First byte
occurrence of the unknown toner 01: Toner container (Fixed)
previous unknown container. Second byte
toner detection is 00: Black
less than 5, all of the 01: Cyan
unknown toner 02: Magenta
detection are 03: Yellow
logged.
1-3-15
2LK/2LN/2LM/2LC

U000
(12) Counter Log (f) Paper jam (g) Self diagnostic (h) Maintenance item
error replacing
Comprised of
Indicates the log Indicates the log Indicates the log coun-
three log coun- counter of paper counter of self diag- ter depending on the
ters including jams depending on nostics errors maintenance item for
paper jams, self
location. depending on maintenance.
diagnostics cause.
errors, and Refer to Paper Jam T: Toner container
replacement of
Log. Example: 00: Black
the toner con- C6000: 4 01: Cyan
tainer. All instances includ- 02: Magenta
ing those are not Self diagnostics 03: Yellow
occurred are dis- error 6000 has hap- M: Maintenance kit
played. pened four times. 01: MK-8305A/8505A
02: MK-8305B/8505B
03: MK-8305C/8505C
Example:
T00: 1
The toner container has
been replaced once.
1-3-16
2LK/2LN/2LM/2LC

U000 Service status page (1)
Service Status Page

MFP (2) 27/10/2010 12:00
(3) (4) (5)
(1) Firmware version 2LC_2000.000.000 2010.10.27 [XXXXXXXX] [XXXXXXXX] [XXXXXXXX]
Controller Information
Memory status
(7) Total Size 2.0 GB (32) FRPO Status
Default Pattern Switch B8 0
Time Default Font Number C5*1000+C2*100+C3 00000
(8) Local Time Zone +01:00 Amsterdam .
(9) Date and Time 27/10/2010 12:00 .
(10) Time Server 10.183.53.13 .
.
Installed Options .
(11) Document Processor Installed .
(12) Paper feeder Cassette .
(13) Finisher 1000-Finisher .
(14) Job Separator Installed .
(15) Document Guaed (A) Installed .
(16) Card Authentication Kit (B) Installed .
(17) Internet FAX Kit (A) Installed .
(18) Security Kit (E) Installed .
Data Security Kit (E) Software Type I .
(19) UG-34 Installed .
.
Print Coverage .
(20) Average(%) / Usage Page(A4/Letter Conversion) .
(21) Total .
K: 1.10 / 1111111.11 .
C: 2.20 / 2222222.22 .
M: 3.30 / 3333333.33 .
Y: 4.40 / 4444444.44
(22) Copy e-MPS error control Y6 0
K: 1.10 / 1111111.11
C: 2.20 / 2222222.22
M: 3.30 / 3333333.33
Y: 4.40 / 4444444.44
(23) Printer
K: 1.10 / 1111111.11
C: 2.20 / 2222222.22
M: 3.30 / 3333333.33
Y: 4.40 / 4444444.44
(24) FAX
K: 1.10 / 1111111.11
(25) Period (27/10/2010 - 03/11/2010 08:40)
(26) Last Page K/C/M/Y(%) 1.00 / 2.22 / 3.33 / 4.44
(27) FAX Information Slot1/Slot2

(28) Rings (Normal) 3
(29) Rings (FAX/TEL) 3
(30) Rings (TAD) 3
(31) Option DIMM Size 16 MB
1 (6) [XXXXXXXXXXXXXXXX]
Figure 1-3-2
1-3-17
2LK/2LN/2LM/2LC

U000 Service status page (2)
Service Status Page

MFP 27/10/2010 12:00
Firmware version 2LC_2000.000.000 2010.10.27 [XXXXXXXX] [XXXXXXXX] [XXXXXXXX]
Engine Information Send Information

(33) NVRAM Version _1F31225_1F31225 (37) Date and Time 10/10/27
(34) Scanner Version 2LC_1200.001.089 (38) Address
(35) FAX Slot1
FAX BOOT Version 2LC_5000.001.001
FAX APL Version 2LC_5100.001.001
FAX IPL Version 2LC_5200.001.001
(36) MAC Address 00:C0:EE:D0:01:0D
1/2 (39) (40)

(41) 100/100
(42) 0/0/0/0/0/0/0/0
(43) 0000000/0000000/0000000/0000000/0000000/0000000/0000000/
(44) 0000000/0000000/0000000/0000000/0000000/0000000/0000000/0000000/0000000/0000000/0000000/
F00/U00/0/0/0/0/30/30/70/70/abcde/1/0 (45) (46) (47) (48) (49) (50) (51) (52) (53) (54) (55) (56) (57)
(58) 0000/0000/0000/0000/0000/0000/0000/0000/0000/0000/0000/0000/0000/0000/0000/
0000/0000/0000/0000/0000/0000/0000/0000/0000/0000/
(59) 0000/0100/0500/1000/0000/0100/0500/1000/0000/0100/0500/1000/0000/0100/0500/1000/
0000/0100/0500/1000/0000/0100/0500/1000/0000/0100/0500/1000/0000/0100/0500/1000/
00000000000000000000000000000000/0000000000000000000000000000000000000000/0000000000/ (60) (61) (62)
0000000000000000/0000000000000000/0000000000000000/0000000000000000/0000000000000000/
0000000000000000/0000000000000000/0000000000000000/0000000000000000/0000000000000000/
0000000000000000/0000000000000000/0000000000000000/0000000000000000/0000000000000000/
(64) 0000000000000000/0000000000000000/0000000000000000/0000000000000000/0000000000000000/
(65) 0000000000000000/0000000000000000/0000000000000000/0000000000000000/
(66) 0000000000000000/0000000000000000/0000000000000000/0000000000000000/0000000000000000/
0000000000000000/0000000000000000/0000000000000000/0000000000000000/0000000000000000/
(67) 0000000000000000/0000000000000000/0000000000000000/0000000000000000/0000000000000000/
(68) 0000000000000000/0000000000000000/0000000000000000/0000000000000000/0000000000000000/
(69) 12345678/11223344/00001234abcd567800001234abcd5678/01234567890123456789012345678901/0008/00/07
12345678/11223344/00001234abcd567800001234abcd5678/01234567890123456789012345678901/0008/00/07
12345678/11223344/00001234abcd567800001234abcd5678/01234567890123456789012345678901/0008/00/07
12345678/11223344/00001234abcd567800001234abcd5678/01234567890123456789012345678901/0008/00/07
(70) XXXXXXXX
(71) [ABCDEFGHIJ][ABCDEFGHIJ]
(72) 00070107FE/0700FE00FE/00FE000100/0000000000/0000000000/0000000000/00000A010A/0A0A0A3200/
0008000000/080000001D/0096009B00/9B009BFFFB/0082000000/000000001F/0000002C00/0000000000/
0000000000/0000000000/0000000000/0000000000/0000000000/0000000000/0000000000/0000010105/
010A000000/0000000000/003C4C0100/0000000087/A28000363C/8000676B83/0000000000/0000000000/
0000000000/0000000000/0000000000/0000000000/0000000000/0000000000/0000000000/0000000005/
0000000000/0000000000/0000000000/0000000000/0000000000/000000024E/
(73) ABCDEFGHIJ/ABCDEFGHIJ/ABCDEFGHIJ/ABCDEFGHIJ/
2 [XXXXXXXXXXXXXXXX]
Figure 1-3-3
1-3-18
2LK/2LN/2LM/2LC

U000 Detail of service status page
No. Description Supplement
(1) Firmware version -
(2) System date -
(3) Engine soft version -
(4) Engine boot version -
(5) Operation panel mask version -
(6) Machine serial number -
(7) Total memory size -
(8) Local time zone -
(9) Report output date Day/Month/Year hour:minute
(10) NTP server name -
(11) Presence or absence of the Installed/Not Installed
document processor
(12) Presence or absence of the Paper feeder/Large capacity feeder/Not Installed
paper feeder
(13) Presence or absence of the 1000-sheet finisher/4000-sheet finisher/
finisher Not Installed
job separator
printed document guard kit
(16) Presence or absence of the IC Installed/Not Installed/Trial
card authentication kit
internet fax kit
data security kit
UG-34
(20) Page of relation to the A4/Letter -
(21) Average coverage for total Black/Cyan/Magenta/Yellow
(22) Average coverage for copy Black/Cyan/Magenta/Yellow
(23) Average coverage for printer Black/Cyan/Magenta/Yellow
(24) Average coverage for fax Black/Cyan/Magenta/Yellow
(25) Cleared date and output date -
(26) Coverage on the final output -
page
1-3-19
2LK/2LN/2LM/2LC

U000
(27) Fax kit information This item is printed only when the fax kit is
installed.
(28) Number of rings 0 to 15
(29) Number of rings before auto- 0 to 15
matic switching
(30) Number of rings before connect- 0 to 15
ing to answering machine
(31) Optional DIMM size -
(32) FRPO setting -
(33) NV RAM version _ 1F3 1225 _ 1F3 1225
(a) (b) (c) (d) (e) (f)
(a) Consistency of the present software version

and the database
_ (underscore): OK
* (Asterisk): NG
(b) Database version
(c) The oldest time stamp of database version
(d) Consistency of the present software version
and the ME firmware version
_ (underscore): OK
* (Asterisk): NG
(e) ME firmware version
(f) The oldest time stamp of the ME database ver-
sion
Normal if (a) and (d) are underscored, and (b) and
(e) are identical with (c) and (f).
(34) Scanner firmware version -
(35) Fax firmware version This item is printed only when the fax kit is
installed.
(36) Mac address -
(37) The last sent date and time -
(38) Transmission address -
(39) Destination information -
(40) Area information -
(41) Margin settings Top margin/Left margin
(42) Margin/Page length/Page width Top margin integer part/Top margin decimal part/
settings Left margin integer part/Left margin decimal part/
Page length integer part/Page length decimal part/
Page width integer part/Page width decimal part
1-3-20
2LK/2LN/2LM/2LC

U000
(43) Life counter (The first line) Machine life/MP tray/Cassette 1/Cassette 2/
Cassette 3/Cassette 4/Duplex
(44) Life counter (The second line) Drum unit K/Drum unit C/Drum unit M/Drum unit Y/
Transfer belt unit/Developer unit K/
Developer unit C/Developer unit M/
Developer unit Y/Maintenance kit A/
Maintenance kit B
(45) Panel lock information 0: OFF/1: Partial lock/2: Full lock
(46) USB information U00: Not installed/U01: Full speed/U02: Hi speed
(47) Paper handling information 0: Paper source unit select/1: Paper source unit
(48) Color printing double count 0: All single counts
mode 1: A3, Single count, Less than 420 mm (length)
2: Legal, Single count, 356 mm or less (length)
3: Folio, Single count, Less than 330 mm (length)
(49) Black and white printing double 0: All single counts
count mode 1: A3, Single count, Less than 420 mm (length)
2: Legal, Single count, 356 mm or less (length)
3: Folio, Single count, Less than 330 mm (length)
(50) Billing counting timing -
(51) Temperature (machine inside) -
(52) Temperature (machine outside) -
(53) Relative temperature -
(machine outside)
(54) Absolute temperature -
(machine outside)
(55) Fixed assets number -
(56) Job end judgment time-out time -
(57) Job end detection mode -
(58) Media type attributes Weight settings Fuser settings
1 to 28 (Not used: 18, 19, 20) 0: Light 0: High
1: Normal 1 1: Middle
2: Normal 2 2: Low
3: Normal 3 3: Vellum
4: Heavy 1 Duplex settings
5: Heavy 2 0: Disable
6: Heavy 3 1: Enable
7: Extra Heavy
1-3-21
2LK/2LN/2LM/2LC

U000
(59) Calibration information Black/Cyan/Magenta/Yellow
(60) Calibration information -
(69) RFID information -
(70) RFID reader/writer version infor- -
mation
(71) Color table version -
(72) Color table 2 version -
(73) Maintenance information -
Code conversion
A B C D E F G H I J
0 1 2 3 4 5 6 7 8 9
Completion
U001 Exiting the maintenance mode
Description
Exits the maintenance mode and returns to the normal copy mode.
Purpose
To exit the maintenance mode.
Method
1. Press the start key. The normal copy mode is entered.
1-3-22
2LK/2LN/2LM/2LC

U002 Setting the factory default data
Description
Restores the machine conditions to the factory default settings.
Purpose
To move the mirror frame of the scanner to the position for transport.
Method
2. Select [Mode1(All)].
The mirror frame of the scanner returns to the home position.
* : An error code is displayed in case of an initialization error.
When errors occurred, turn main power switch off then on, and execute initialization using
maintenance item U002.
Error codes
Codes Description
0001 Entity error
0002 Controller error
0020 Engine error
0040 Scanner error
U003 Setting the service telephone number
Description
Sets the telephone number to be displayed when a service call code is detected.
Purpose
To set the telephone number to call service when installing the machine.
Setting
The keys to enter the number are displayed on the touch panel.
2. Enter a telephone number (up to 15 digits).
3. Press the start key. The setting is set.
Completion
1-3-23
2LK/2LN/2LM/2LC

U004 Setting the machine number
Description
Sets or displays the machine number.
Purpose
To check or set the machine number.
Method
If the machine serial number of engine PWB matches with that of main PWB
Display Description
Machine No. Displays the machine serial number
If the machine serial number of engine PWB does not match with that of main PWB
Display Description
Machine No.(Main) Displays the machine serial number of main
Machine No.(Eng) Displays the machine serial number of engine
Setting
Carry out if the machine serial number does not match.
1. Select [Execute].
2. Press the start key. Writing of serial No. starts.
Completion
1-3-24
2LK/2LN/2LM/2LC

U010 Setting the maintenance mode ID
Description
Sets the maintenance mode ID.
Purpose
Modify maintenance mode ID for more security.
Method
Display Description
New ID Enter a new 8-digit ID
New ID(Reconfirm) Enter a new 8-digit ID (to confirm)
Initialize Initialize the ID
Setting
1. Select [New ID].
2. Enter a new 8-digit ID on ten keys (0 – 9, *, #). * and # are mandatory to contain.
3. Select [New ID(Reconfirm)].
4. Enter a new 8-digit ID on ten keys (0 – 9, *, #).
Method: [Initialize]
1. Select [Initialize].
2. Press the start key. ID is initialized.
Completion
1-3-25
2LK/2LN/2LM/2LC

U019 Displaying the ROM version
Description
Displays the part number of the ROM fitted to each PWB.
Purpose
To check the part number or to decide, if the newest version of ROM is installed.
Method
1. Press the start key. The ROM version are displayed.
2. Change the screen using the cursor up/down keys.
Display Description
Main Main ROM
MMI Operation ROM
Browser Browser ROM
Engine Engine ROM
Engine Boot Engine booting
Scanner Scanner ROM
Scanner Boot Scanner booting
RFID RFID ROM
IH CPU IH CPU ROM
IH CPU Boot IH CPU booting
Motor CPU Motor CPU ROM
Motor CPU Boot Motor CPU booting
Dictionary -
Option Language Optional language ROM
PDF1.7 Resource PDF1.7 resource ROM
Solution Framework Framework ROM
FMU FMU ROM
Weekly Timer Weekly Timer ROM
Color Table1(Copy) Color table 1 (copy) ROM
Color Table2(Copy) Color table 2 (copy) ROM
Color Table1(Prn) Color table 1 (printer) ROM
Color Table2(Prn) Color table 2 (printer) ROM
DP Document processor ROM
DP Boot Document processor booting
PF1 Paper feeder / Large capacity feeder ROM
PF1 Boot Paper feeder / Large capacity feeder booting
Side PF SMT paper feeder /Side feeder ROM
Side PF Boot SMT paper feeder /Side feeder booting
1-3-26
2LK/2LN/2LM/2LC

U019
Display Description
PF2 Side paper feeder / Side large capacity feeder ROM
PF2 Boot Side paper feeder / Side large capacity feeder booting
DF 1000-sheet finisher / 4000-sheet finisher ROM
DF Boot 1000-sheet finisher / 4000-sheet finisher booting
PH Punch unit ROM
PH Boot Punch unit booting
MT Mailbox ROM
MT Boot Mailbox booting
BF Center-folding unit ROM
BF Boot Center-folding unit booting
Fax APL1 Fax APL 1
Fax Boot1 Fax booting 1
Fax IPL1 Fax IPL 1
Fax APL2 Fax APL 2 (dual Fax)
Fax Boot2 Fax booting 2 (dual Fax)
Fax IPL2 Fax IPL 2 (dual Fax)
Completion
1-3-27
2LK/2LN/2LM/2LC

U021 Memory initializing
Description
Initializes all settings, except those pertinent to the type of machine, namely each counter, ser-
vice call history and mode setting. Also initializes backup RAM according to region specification
selected in maintenance item U252 Setting the destination.
Purpose
To return the machine settings to their factory default.
Method
3. Press the start key. All data other than that for adjustments due to variations between
machines is initialized based on the destination setting.
Error codes
Codes Description
0001 Entity error
0020 Engine error
0040 Scanner error
1-3-28
2LK/2LN/2LM/2LC

U024 HDD formatting
Description
Initializes the hard disk.
Purpose
To initialize the hard disk when replacing the hard disk after shipping.
Caution
In addition, the following settings are also initialized by initializing the hard disk.
System menu (user login administration, job accounting, address book, one-touch keys and doc-
ument box etc.), shortcuts and panel programs
When fully formatted, the following pre-installed software are removed.
Option language, PDF1.7 resource, FMU, weekly timer
Method
2. Select the item.
Display Description
Full Full format
Data Data format (the application software are retained)
3. Press [Execute].
4. Press the start key to initialize the hard disk.
1-3-29
2LK/2LN/2LM/2LC

U030 Checking the operation of the motors
Description
Drives each motor.
Purpose
To check the operation of each motor.
Method
2. Select the motor to be operated.
3. Press the start key. The operation starts.
Display Description
Feed Paper feed motor (PFM) is turned on
DLP(K) Developer motor K (DEVM-K) is turned on
DLP(CMY) Developer motor MCY (DEVM-MCY) is turned on
Fuser Fuser motor (FUM) is turned on
SB(CW) Eject motor (EM) is turned on clockwise
SB(CCW) Eject motor (EM) is turned on counterclockwise
CMY Release Color release motor (CRM) is turned on
Job Separator Job eject motor (JEM) is turned on
Regist Registration motor (RM) is turned on (45 ppm/55 ppm model only)
Bridge1 Bridge conveying motor 1 (BRCM1) is turned on
Bridge2 Bridge conveying motor 2 (BRCM2) is turned on
Belt Meand Transfer motor (TRM) is turned on
Press Release Transfer release motor (TRRM) is turned on
Fuser Release Fuser release motor (FURM) is turned on
DU1 Duplex motor 1 (DUM1) is turned on
DU2 Duplex motor 2 (DUM2) is turned on
Mid Roller Middle motor (RM) is turned on (45 ppm/55 ppm model only)
4. To stop operation, press the stop key.
Completion
1-3-30
2LK/2LN/2LM/2LC

U031 Checking switches and sensors for paper conveying
Description
Displays the on-off status of each paper detection switch or sensor on the paper path.
Purpose
To check if the switches and sensors for paper conveying operate correctly.
Method
2. Turn each switch or sensor on and off manually to check the status.
When the on-status of a switch or sensor is detected, that switch or sensor is displayed in
reverse.
Display Description
MPT Jam MP feed sensor (MPFS)
Cassette1 Feed Feed sensor 1 (FS1)
Cassette2 Feed Feed sensor 2 (FS2)
Feed2(Feed B) Paper conveying sensor (PCS)
Regist Registration sensor (RS)
Belt Jam Transfer belt sensor (TRBLS)
DU1 Duplex sensor 1 (DUS1)
DU2 Duplex sensor 2 (DUS2)
Bridge1 Feed Bridge conveying sensor 1 (BRCS1)
Bridge2 Feed Bridge conveying sensor 2 (BRCS2)
Bridge Exit Bridge eject sensor (BRES)
Exit Paper Eject full sensor (EFS)
Fuser Feed Fuser eject sensor (FUES)
Feed1(Mid) Middle sensor (MS)
Exit Job Separator Switchback sensor (SBS)
Regist Loop Sensor Loop sensor (LPS)
Completion
1-3-31
2LK/2LN/2LM/2LC

U032 Checking the operation of the clutches
Description
Turns each clutch on.
Purpose
To check the operation of each clutch.
Method
2. Select the clutch to be operated.
Display Description
Feed1 Paper feed clutch 1 (PFCL1) is turned on
Feed2 Paper feed clutch 2 (PFCL2) is turned on
Mid Roller Middle clutch (MCL)*1 is turned on
MPT Feed MP paper feed clutch (MPPFCL) is turned on
Regist Registration clutch (RCL)*1 is turned on
Feed Paper conveying clutch (PCCL) is turned on
DU1 Duplex clutch 1 (DUCL1)*1 is turned on
DU2 Duplex clutch 2 (DUCL2)*1 is turned on
Assist1 Assist clutch 1 (ASCL1)*2 is turned on
Assist2 Assist clutch 2 (ASCL2*2 is turned on
Motor Paper feed motor (PFM) is turned on
*1: 30 ppm/35 ppm model only. *2: 45 ppm/55 ppm model only.
Completion
1-3-32
2LK/2LN/2LM/2LC

U033 Checking the operation of the solenoids
Description
Turns each solenoid on.
Purpose
To check the operation of each solenoid.
Method
2. Select the solenoid to be operated.z
Display Description
Pick Up1 Pickup solenoid 1 (PUSOL1)* is turned on
Pick Up2 Pickup solenoid 2 (PUSOL2)* is turned on
Job Separator Feedshift solenoid (FSSOL) is turned on
ID Clean Cleaning solenoid (CLSOL) is turned on
Bridge Solenoid Bridge solenoid (BRSOL) is turned on
Motor Paper feed motor (PFM) is turned on
*: 45 ppm/55 ppm model only.

Completion
U034 Adjusting the print start timing
Description
Adjusts the leading edge registration or center line.
Purpose
Make the adjustment if there is a regular error between the leading edges of the copy image and
original.
Make the adjustment if there is a regular error between the center lines of the copy image and
original.
Method
2. Select the item to be adjusted.
Display Description
LSU Out Top Leading edge registration adjustment
LSU Out Left Center line adjustment
LSU Out Top B/W Leading edge registration adjustment in black/white mode
LSU Out Top 3/4 Leading edge registration adjustment at 3/4 times of line speed
1-3-33
2LK/2LN/2LM/2LC

U034 Adjustment: Leading edge registration adjustment
1. Press the system menu key.
2. Press the start key to output a test pattern.
[LSU Out Top]
Setting Initial Change in
Display Description
range setting value per step
MPT(L) Paper feed from MP tray -3.0 to 3.0 0 0.1 mm
(when large size paper is used)
MPT Half(L) Paper feed from MP tray -3.0 to 3.0 0 0.1 mm
(when large size thick paper is used)
Cassette(L) Paper feed from cassette -3.0 to 3.0 0 0.1 mm
Cassette Paper feed from cassette -3.0 to 3.0 0 0.1 mm
Half(L) (when large size thick paper is used)
Duplex(L) Duplex mode (second) -3.0 to 3.0 0 0.1 mm
Duplex Duplex mode (second) -3.0 to 3.0 0 0.1 mm
MPT(S) Paper feed from MP tray -3.0 to 3.0 0 0.1 mm
(when small size paper is used)
MPT Paper feed from MP tray -3.0 to 3.0 0 0.1 mm
Half(S) (when small size thick paper is used)
Cassette(S) Paper feed from cassette -3.0 to 3.0 0 0.1 mm
Cassette Paper feed from cassette -3.0 to 3.0 0 0.1 mm
Duplex(S) Duplex mode (second) -3.0 to 3.0 0 0.1 mm
Large size: 218 mm or more in width of paper.
1-3-34
2LK/2LN/2LM/2LC

U034 [LSU Out Top B/W] [LSU Out Top 3/4]
Display Description
MPT(L) Paper feed from MP tray -3.0 to 3.0 0 0.1 mm
Cassette(L) Paper feed from cassette -3.0 to 3.0 0 0.1 mm
Duplex(L) Duplex mode (second) -3.0 to 3.0 0 0.1 mm
MPT(S) Paper feed from MP tray -3.0 to 3.0 0 0.1 mm
Cassette(S) Paper feed from cassette -3.0 to 3.0 0 0.1 mm
Duplex(S) Duplex mode (second) -3.0 to 3.0 0 0.1 mm
5. Change the setting value using the cursor +/- or numeric keys.
For output example 1, increase the value. For output example 2, decrease the value.
Leading edge
registration
(20 ± 1.0 mm)
Correct image Output Output

example 1 example 2
Figure 1-3-4
6. Press the start key. The value is set.
Remark
When changing the setting value of [Large] each item is modified, equal to amount of the value
which is changed adds also the value of [Small] each item and is pulled.
Caution
Check the copy image after the adjustment. If the image is still incorrect, perform the following
adjustments in maintenance mode.
U066 U071
U034 (P.1-3-53) (P.1-3-58)
1-3-35
2LK/2LN/2LM/2LC

U034 Adjustment: Center line adjustment
Display Description
MPT Paper feed from MP tray -3.0 to 3.0 0 0.1 mm
Cassette1 Paper feed from cassette 1 -3.0 to 3.0 0 0.1 mm
Cassette2 Paper feed from cassette 2 -3.0 to 3.0 0 0.1 mm
Cassette3 Paper feed from optional cassette 3 -3.0 to 3.0 0 0.1 mm
Cassette6 Paper feed from optional cassette 6* -3.0 to 3.0 0 0.1 mm
Cassette7 Paper feed from optional cassette 7* -3.0 to 3.0 0 0.1 mm
*: 45 ppm/55 ppm model only.
5. Change the setting value using the +/- keys or numeric keys.
Center line of printing

(within ± 2.0 mm)
Correct image Output Output

example 1 example 2
Figure 1-3-5
Caution
U067 U072
U034 (P.1-3-54) (P.1-3-60)
Completion
1-3-36
2LK/2LN/2LM/2LC

U035 Setting the printing area for folio paper
Description
Changes the printing area for copying on folio paper.
Purpose
To prevent cropped images on the trailing edge or left/right side of copy paper by setting the
actual printing area for folio paper.
Setting
2. Select the item to be set.
3. Change the setting value using the +/- keys.
Display Description Setting range Initial setting
Length Length 330 to 356 mm 330
Width Width 200 to 220 mm 210
Completion
1-3-37
2LK/2LN/2LM/2LC

U037 Checking the operation of the fan motors
Description
Drives each fan motor.
Purpose
To check the operation of each fan motor.
Method
2. Select the fan motor to be operated.
Display Description Group
Fuser Cooling Coil fan motor 2 (CFM2) is turned on B
DLP Rear
LSU Cooling LSU fan motor (LSUFM) is turned on B
Belt Cooling Belt fan motor 1and 2 (BLFM1, 2) is turned on A
Exit Paper Eject fan motor 1and 2 (EFM1, 2) is turned on B
Exit Cooling Eject front fan motor (EFFM) is turned on B
Toner Toner fan motor 1and 2 (TFM1, 2) is turned on A
Low Volt Power source fan motor (PSFM) is turned on A
Exit Rear Cooling Eject rear fan motor (EFRM) is turned on A
IH PWB IH fan motor (IHFM) is turned on A
IH Coil Coil fan motor 1 (CFM1) is turned on A
DLP(K) Developer fan motor 1 (DEVFM1) is turned on A
DLP Front Developer fan motor 2 (DEVFM2) is turned on A
Conv Edge Fuser fan motor 1and 2 (FUFM1, 2) is turned on A
Fuser Edge Fuser front/rear fan motor (FUFFM/FURFM) is turned on -
GroupA Fan motors of group A are turned on
GroupB Fan motors of group B are turned on
Completion
1-3-38
2LK/2LN/2LM/2LC

U039 Adjusting the magnification
Description
Adjusts the magnification of the printing.
Purpose
Make the adjustment if the magnification in the main scanning direction is incorrect.
Make the adjustment if the magnification in the auxiliary scanning direction is incorrect.
Caution
Adjust the magnification of the scanner in the following order.
U065 U070
U039
(P.1-3-51) (P.1-3-56)
Method
Display Description
Horizon Magnification in the main -1 to 1 0 0.1 %
scanning direction
Vertical Magnification in the auxiliary -1 to 1 0 0.1 %
scanning direction
Adjustment: [Horizon]
Increasing the setting makes the image longer, and decreasing it makes the image shorter.
250 ± 1.0 mm
Figure 1-3-6
1-3-39
2LK/2LN/2LM/2LC

U039 Adjustment: [Vertical]
Increasing the setting makes the image longer, and decreasing it makes the image shorter.
350 ± 1.4 mm
Figure 1-3-7
Completion
Press the stop key. The indication for selecting a maintenance item No. appears.
U051 Adjusting the deflection in the paper
Description
Adjusts the deflection in the paper at the registration roller.
Purpose
Make the adjustment if the leading edge of the copy image is missing or varies randomly, or if the
copy paper is Z-folded.
Method
Display Description
Paper Loop Amount Deflection adjustment
Paper Loop Amount B/W Deflection adjustment in black and white mode
Paper Loop Amount 3/4 Deflection adjustment at 3/4 times of line speed
1-3-40
2LK/2LN/2LM/2LC

U051 Adjustment
2. Place an original and press the start key to make a test copy.
4. Select the item to be adjusted.[LSU Out Top]
[Paper Loop Amount]
Display Description
MPT(L) Paper feed from MP tray -30 to 20 0 1.0 mm
MPT Half(L) Paper feed from MP tray -30 to 20 0 1.0 mm
(when large size thick paper is used)
Cassette(L) Paper feed from cassette -30 to 20 0 1.0 mm
Cassette Paper feed from cassette -30 to 20 0 1.0 mm
Duplex(L) Duplex mode (second) -30 to 20 0 1.0 mm
Duplex Duplex mode (second) -30 to 20 0 1.0 mm
MPT(S) Paper feed from MP tray -30 to 20 0 1.0 mm
MPT Paper feed from MP tray -30 to 20 0 1.0 mm
Cassette(S) Paper feed from cassette -30 to 20 0 1.0 mm
Cassette Paper feed from cassette -30 to 20 0 1.0 mm
Duplex(S) Duplex mode (second) -30 to 20 0 1.0 mm
Duplex Duplex mode (second) -30 to 20 0 1.0 mm
1-3-41
2LK/2LN/2LM/2LC

U051 [LSU Out Top B/W] [LSU Out Top 3/4]
Display Description
MPT(L) Paper feed from MP tray -30 to 20 0 1.0 mm
Cassette(L) Paper feed from cassette -30 to 20 0 1.0 mm
Duplex(L) Duplex mode (second) -30 to 20 0 1.0 mm
MPT(S) Paper feed from MP tray -30 to 20 0 1.0 mm
Cassette(S) Paper feed from cassette -30 to 20 0 1.0 mm
Duplex(S) Duplex mode (second) -30 to 20 0 1.0 mm
The greater the value, the larger the deflection; the smaller the value, the smaller the deflec-
tion.
Original Copy Copy

example 1 example 2
Figure 1-3-8
Completion
1-3-42
2LK/2LN/2LM/2LC

U052 Setting the fuser motor control
Description
Enters the sensor data values described on the supplied sheet provided when the loop sensor is
replaced and performs correction processing for the fuser motor.
Purpose
To perform when replacing the loop sensor or paper conveying unit.
Method
2. Select the item.
Display Description
Set Loop Sensor Enter the data value for loop sensor
Loop Sensor Control Set the loop sensor detection control
Set Loop Sensor Valid Sets the presence or absence of the loop sensor
Method: [Set Loop Sensor] How to read the sensor data value
1. Select [Scanning Board1]. (e.g.) 1
2. Enter the sensor data value of supplied sheet DATA1 using 2
3
the +/- keys. 4
3. Select [Scanning Board2]. 5
6
4. Enter the sensor data value of supplied sheet DATA2 using 7
the +/- keys. 8
5. Press the start key. The value is set. 9
0
3 6 4
Setting: [Loop Sensor Control]
1. Select the item.
2. Select On or Off.
Display Description Initial setting
No.1 Sensor detection On/Off setting at 125 to 250 mm from Off
the top of paper
No.2 Sensor detection On/Off setting at 250 to 290 mm from On
the top of paper
the top of paper
the top of paper
Setting: [Set Loop Sensor Valid]

Initial setting: On
Completion
1-3-43
2LK/2LN/2LM/2LC

U053 Setting the adjustment of the motor speed
Description
Performs fine adjustment of the speeds of the motors.
Purpose
Basically, the setting need not be changed. Modify settings by interlock setting only if faulty
images occur.
Method
2. Select the item to be adjusted
Display Description
Moter1 Adjustment of drum motor K, M, C, Y speeds
Moter2 Adjustment of developer motor K, developer motor MCY, transfer
motor, registration motor and transfer cleaning motor speeds
Moter3 Adjustment of eject motor, fuser motor, bridge conveying motor 1/2,
paper feed motor, job eject motor, middle motor and duplex motor
speeds
Moter4 Drum motor K speed adjustment in black/white mode
Moter5 Adjustment of developer motor K, transfer motor, registration motor
and transfer cleaning motor speeds in black/white mode
Moter6 Adjustment of eject motor, fuser motor, bridge conveying motor 1/2,
paper feed motor, job eject motor, middle motor and duplex motor
speeds in black/white mode
Moter1 Half Adjustment of drum motor K, M, C, Y speeds in half speed
Moter2 Half Adjustment of developer motor K, developer motor MCY and transfer
motor speeds in half speed
Moter3 Half Adjustment of eject motor, bridge conveying motor 1/2, paper feed
motor, middle motor and duplex motor speeds in half speed
Moter1 3/4 Adjustment of drum motor K, M, C, Y speeds at 3/4 times of line
speed
Moter2 3/4 Adjustment of developer motor K, developer motor MCY, transfer
motor, registration motor and transfer cleaning motor speeds at 3/4
times of line speed
Moter3 3/4 Adjustment of eject motor, fuser motor, bridge conveying motor 1/2,
paper feed motor, job eject motor and middle motor speeds at 3/4
times of line speed
1-3-44
2LK/2LN/2LM/2LC

U053 Setting: [Motor1]
Setting Initial
Display Description
range setting
Drum(K) Drum motor K (DRM-K) -500 to 500 0
Drum(CMY) Drum motor C, M, Y (DRM-C, M, Y) -500 to 500 0
Setting: [Motor2]
Setting Initial
Display Description
range setting
Dev(K) Developer motor K (DEVM-K) -500 to 500 0
Dev(CMY) Developer motor MCY (DEVM-MCY) -500 to 500 0
Trans Belt Transfer motor (TRM) -500 to 500 0
Regist* Registration motor (RM) -500 to 500 0
Belt Clean Transfer cleaning motor (TRCM) -500 to 500 0
Setting: [Motor3]
Setting Initial
Display Description
range setting
SB Eject motor (EM) -500 to 500 0
Fixing Fuser motor (FUM) -500 to 500 0
Bridge1 Bridge conveying motor 1 (BRCM1) -500 to 500 0
Feed Paper feed motor (PFM) -500 to 500 0
Job Separator Job eject motor (JEM) -500 to 500 0
Mid Roller* Middle motor (MM) -500 to 500 0
DU* Duplex motor (DUM) -500 to 500 0
Setting: [Motor4]
Setting Initial
Display Description
range setting
Drum B/W(K) Drum motor K (DRM-K) in black/white -500 to 500 0
mode
Drum Mono(K) Drum motor K (DRM-K) in mono- -500 to 500 0
chrome mode
1-3-45
2LK/2LN/2LM/2LC

U053 Setting: [Motor5]
Setting Initial
Display Description
range setting
Dev B/W(K) Developer motor K (DEVM-K) in -500 to 500 0
black/white mode
Trans Belt B/W Transfer motor (TRM) in black/white -500 to 500 0
mode
Regist B/W* Registration motor (RM) in black/white -500 to 500 0
mode
Belt Clean B/W Transfer cleaning motor (TRCM) in -500 to 500 0
black/white mode
Setting: [Motor6]
Setting Initial
Display Description
range setting
SB B/W Eject motor (EM) in black/white mode -500 to 500 0
Fixing B/W Fuser motor (FUM) in black/white -500 to 500 0
mode
Bridge1 B/W Bridge conveying motor 1 (BRCM1) in -500 to 500 0
black/white mode
Bridge2 B/W Bridge conveying motor 2 (BRCM2) in -500 to 500 0
black/white mode
Feed B/W Paper feed motor (PFM) in black/white -500 to 500 0
mode
Job Separator B/W Job eject motor (JEM) in black/white -500 to 500 0
mode
Mid Roller B/W* Middle motor (MM) in black/white mode -500 to 500 0
DU B/W* Duplex motor (DUM) in black/white -500 to 500 0
mode
Setting: [Motor1 Half]

Setting Initial
Display Description
range setting
Drum(K) Drum motor K (DRM-K) in half speed -500 to 500 0
Drum(CMY) Drum motor C, M, Y (DRM-C, M, Y) in -500 to 500 0
half speed
1-3-46
2LK/2LN/2LM/2LC

U053 Setting: [Motor2 Half]
Setting Initial
Display Description
range setting
Dev(K) Developer motor K (DEVM-K) in half -500 to 500 0
speed
Dev(CMY) Developer motor MCY (DEVM-MCY) in -500 to 500 0
half speed
Trans Belt Transfer motor (TRM) in half speed -500 to 500 0
Setting: [Motor3 Half]

Setting Initial
Display Description
range setting
SB Eject motor (EM) in half speed -500 to 500 0
Bridge1 Bridge conveying motor 1 (BRCM1) in -500 to 500 0
half speed
Bridge2 Bridge conveying motor 2 (BRCM2) in -500 to 500 0
half speed
Feed Paper feed motor (PFM) in half speed -500 to 500 0
Mid Roller* Middle motor (MM) in half speed -500 to 500 0
DU* Duplex motor (DUM) in half speed -500 to 500 0
Setting: [Motor1 3/4]

Setting Initial
Display Description
range setting
Drum(K) Drum motor K (DRM-K) -500 to 500 0
Drum(CMY) Drum motor C, M, Y (DRM-C, M, Y) -500 to 500 0
Setting: [Motor2 3/4]

Setting Initial
Display Description
range setting
Dev(K) Developer motor K (DEVM-K) -500 to 500 0
Dev(CMY) Developer motor MCY (DEVM-MCY) -500 to 500 0
Trans Belt Transfer motor (TRM) -500 to 500 0
Regist* Registration motor (RM) -500 to 500 0
Belt Clean Transfer cleaning motor (TRCM) -500 to 500 0
1-3-47
2LK/2LN/2LM/2LC

U053 Setting: [Motor3 3/4]
Setting Initial
Display Description
range setting
SB Eject motor (EM) -500 to 500 0
Fixing Fuser motor (FUM) -500 to 500 0
Feed Paper feed motor (PFM) -500 to 500 0
Job Separator Job eject motor (JEM) -500 to 500 0
Mid Roller* Middle motor (MM) -500 to 500 0
Completion
1-3-48
2LK/2LN/2LM/2LC

U059 Setting fan mode
Description
Specifies mode for paper conveying fan motors during conveying paper.
Purpose
Change mode if paper crease occurs.
Method
2. Select the mode.
Display Description
Fan Mode Sets temperature at which paper conveying fan motors operate.
Cooling Mode Sets temperature at which the paper conveying fan motors are
switched for controlling.
Setting: [Fan Mode]

1. Select the mode.
Display Description
Mode1 Temperature at which paper conveying fan motors operate: High
Mode2 Temperature at which paper conveying fan motors operate: Normal
Mode3 Temperature at which paper conveying fan motors operate: Low
Auto It begins with Mode2 at power up or recovery from sleep mode, and
switches to Mode3 when the thermistor detects higher than 38 °C.
Initial setting: Mode2
Setting: [Cooling Mode]

Setting Initial
Display Description
range setting
Cooling Mode Amount of shift from the initial standard -3 to 3 (°C) 0
temperature
A larger value advances the operating timing, and a smaller value slows it.
Completion
1-3-49
2LK/2LN/2LM/2LC

U061 Checking the operation of the exposure lamp
Description
Lights the exposure lamp.
Purpose
To check whether the exposure lamp are turned on.
Method
2. Select the item.
Display Description
CCD The exposure lamp lights
CIS The CIS lights (when dual scan DP is installed)
3. Press the start key. The lamp lights.
4. To turn the lamp off, press the stop key.
Completion
U063 Adjusting the shading position
Description
Changes the shading position of the scanner.
Purpose
Used when the white line continue to appear longitudinally on the image after the shading plate is
cleaned.
This is due to flaws or stains inside the shading plate. To prevent this problem, the shading posi-
tion should be changed so that shading is possible without being affected by the flaws or stains.
Setting
Display Description
Position Shading position 0 to 18 0 0.091 mm
Increasing the value moves the shading position toward the machine left, and decreasing it
moves the position toward the machine right.
Supplement
While this maintenance item is being executed, copying from an original is available in interrupt
copying mode (which is activated by pressing the system menu key).
Completion
1-3-50
2LK/2LN/2LM/2LC

U065 Adjusting the scanner magnification
Description
Adjusts the magnification of the original scanning.
Purpose
Make the adjustment if the magnification in the main scanning direction is incorrect.
Make the adjustment if the magnification in the auxiliary scanning direction is incorrect.
Caution
Adjust the magnification of the scanner in the following order.
U053 U065 U065 U067 U070

main scan- auxiliary scan-
(P.1-3-44) ning direction ning direction (P.1-3-54) (P.1-3-56)
Method
Display Description
Y Scan Zoom Scanner magnification in the -75 to 75 0 0.02 %
main scanning direction
X Scan Zoom Scanner magnification in the -125 to 125 0 0.02 %
auxiliary scanning direction
Adjustment: [Y Scan Zoom]

For copy example 1, increase the value. For copy example 2, decrease the value.
Original Copy Copy

example 1 example 2
Figure 1-3-9
1-3-51
2LK/2LN/2LM/2LC

U065 Adjustment: [X Scan Zoom]
Original Copy Copy

example 1 example 2
Figure 1-3-10
Completion
1-3-52
2LK/2LN/2LM/2LC

U066 Adjusting the scanner leading edge registration
Description
Adjusts the scanner leading edge registration of the original scanning.
Purpose
Make the adjustment if there is a regular error between the leading edges of the copy image and
original.
Adjustment
Display Description
Front Scanner leading edge registra- -30 to 30 0 0.158 mm
tion
Rotate Scanner leading edge registra- -30 to 30 0 0.158 mm
tion (rotate copying)
Scanner leading edge registration (within ± 2.5 mm)
Original Copy Copy

example 1 example 2
Figure 1-3-11
Caution
U403 U071 U404

U066 (P.1-3-147) (P.1-3-58) (P.1-3-148)
Completion
1-3-53
2LK/2LN/2LM/2LC

U067 Adjusting the scanner center line
Description
Adjusts the scanner center line of the original scanning.
Purpose
Make the adjustment if there is a regular error between the center lines of the copy image and
original.
Adjustment
5. Select the item to be adjusted.l
Display Description
Front Scanner center line -60 to 60 0 0.085 mm
Rotate Scanner center line (rotate -40 to 40 0 0.085 mm
copying)
Scanner center line (within ± 2.0 mm)
Original Copy Copy

example 1 example 2
Figure 1-3-12
Caution
U403 U072 U404

U067
(P.1-3-147) (P.1-3-60) (P.1-3-148)
Completion
1-3-54
2LK/2LN/2LM/2LC

U068 Adjusting the scanning position for originals from the DP
Description
Adjusts the position for scanning originals from the DP. Performs the test copy at the four scan-
ning positions after adjusting.
Purpose
Used when the image fogging occurs because the scanning position is not proper when the DP is
used. Run U071 to adjust the timing of DP leading edge when the scanning position is changed.
Setting
1. Press the start key.l
Display Description
DP Read Starting position adjustment for -38 to 38 0 0.158 mm
scanning originals
Black Line Scanning position for the test 0 to 3 0 -
copy originals
2. Select [DP Read].
3. Change the setting using the +/- keys or numeric keys.
When the setting value is increased, the scanning position moves to the right and it moves to
the left when the setting value is decreased.
5. Select [Black Line].
8. Set the original (the one which density is known) in the DP and press the system menu key.
9. Press the start key. Test copy is executed.
10. Perform the test copy at each scanning position with the setting value from 0 to 3 and check
that no black line appears and the image is normally scanned.
Completion
1-3-55
2LK/2LN/2LM/2LC

U070 Adjusting the DP magnification
Description
Adjusts the DP original scanning speed.
Purpose
Make the adjustment if the magnification is incorrect in the auxiliary scanning direction when the
DP is used.
Adjustment
3. Place an original on the DP and press the start key to make a test copy.
Display Description
X Scan Magnification in the auxiliary -125 to 125 0 0.02 %
Zoom(F) scanning direction of CCD
(first side)
Zoom(B) scanning direction of CCD
(second side)
Y Scan Magnification in the main scan- -100 to 100 0 0.02 %
Zoom(CIS) ning direction of CIS
Zoom(CIS) scanning direction of CIS
Adjustment: [X Scan Zoom]

Original Copy Copy

example 1 example 2
Figure 1-3-13
1-3-56
2LK/2LN/2LM/2LC

U070 Adjustment: [Y Scan Zoom]
Original Copy Copy

example 1 example 2
Figure 1-3-14
Caution
U071 U404
U070 (P.1-3-58) (P.1-3-148)
Completion
1-3-57
2LK/2LN/2LM/2LC

U071 Adjusting the DP scanning timing
Description
Adjusts the DP original scanning timing.
Purpose
Make the adjustment if there is a regular error between the leading or trailing edges of the origi-
nal and the copy image when the DP is used.
Method
Reversed DP
Display Description
Front Head Leading edge registration of -32 to 32 0 0.085 mm
CCD (first side)
Front Tail Trailing edge registration of -32 to 32 0 0.085 mm
CCD (first side)
Back Head Leading edge registration of -32 to 32 0 0.085 mm
CCD (second side)
Back Tail Trailing edge registration of -32 to 32 0 0.085 mm
CCD (second side)
Dual scan DP
Display Description
Front Head Leading edge registration of -27 to 27 0 0.085 mm
CCD (first side)
Front Tail Trailing edge registration of -27 to 27 0 0.085 mm
CCD (first side)
Back Head Leading edge registration of -27 to 27 0 0.085 mm
CCD (second side)
Back Tail Trailing edge registration of -27 to 27 0 0.085 mm
CCD (second side)
CIS Head Leading edge registration of -27 to 27 0 0.085 mm
CIS
CIS Tail Trailing edge registration of CIS -27 to 27 0 0.085 mm
1-3-58
2LK/2LN/2LM/2LC

U071 Adjustment: Leading edge registration
Original Copy Copy

example 1 example 2
Figure 1-3-15
Caution
If the first side is adjusted, check the second side and if adjustment is required, carry out the
adjustment.
U404
U071 (P.1-3-148)
Adjustment: Trailing edge registration

Original
Copy Copy
example 1 example 2
Figure 1-3-16
Caution
adjustment.
U404
U071 (P.1-3-148)
Completion
1-3-59
2LK/2LN/2LM/2LC

U072 Adjusting the DP center line
Description
Adjusts the scanning start position for the DP original.
Purpose
Make the adjustment if there is a regular error between the centers of the original and the copy
image when the DP is used.
Adjustment
Display Description
Front DP center line (first side) -60 to 60 0 0.085 mm
Back DP center line (second side) -60 to 60 0 0.085 mm
CIS* CIS center line -39 to 39 0 0.085 mm
*: Dual scan DP only
Original Copy Copy

example 1 example 2
Figure 1-3-17
Caution
adjustment.
U404
U072
(P.1-3-148)
Completion
1-3-60
2LK/2LN/2LM/2LC

U073 Checking the scanner operation
Description
Simulates the scanner operation under the arbitrary conditions.
Purpose
To check the scanner operation.
Method
2. Select the item to be operated.
Display Description
Scanner Motor Scanner operation
Home Position Home position operation
Dust Check Dust adhesion check operation with lamp on
DP Reading DP scanning position operation
Setting: [Scanner Motor]

1. Select [Scanner Motor].
2. Select the item.
3. Change the setting using the +/- keys.
Display Operating conditions Setting range
Zoom Magnification 25 to 400 %
Size Original size See below.
Lamp On and off of the exposure lamp 0 (off) or 1 (on)
Original sizes for each setting in SIZE
Setting Paper size Setting Paper size
5000 A4 5000 A5R
4300 B5 7800 Folio
5100 11" x 8 1/2" 10200 11" x 17"
10000 A3 9000 11" x 15"
8600 B4 8400 8 1/2" x 14"
7100 A4R 6600 8 1/2" x 11"
6100 B5R 5100 5 1/2" x 8 1/2"
4. Press the start key. Scanning starts under the selected conditions.
1-3-61
2LK/2LN/2LM/2LC

U073 Method: [Home Position]
1. Select [Home Position].
The mirror frame of the scanner moves to the home position.
Method: [Dust Check]

1. Select [Dust Check].
2. Press the start key. The exposure lamp lights.
3. To turn the exposure lamp off, press the stop key.
Method: [DP Reading]

1. Select [DP Reading].
The mirror frame of the scanner moves to the reading position.
Completion
Press the stop key when scanning stops. The screen for selecting a maintenance item No. is dis-
played.
U074 Adjusting the DP input light luminosity
Description
Sets the luminosity correction for scanning originals from the DP.
Purpose
Modify the setting only if a spotted background appears when a bluish original is scanned from
the DP.
Setting
2. Change the setting using the +/- or numeric keys.
Setting Initial
Display Description
range setting
Coefficient DP input light luminosity correction 0 to 3 0
Settings 0: No correction / 1: Slight correction / 2: Medium correction / 3: Strong correction
Supplement
Completion
1-3-62
2LK/2LN/2LM/2LC

U087 Setting DP reading position modification operation
Description
The presence or absence of dust is determined by comparing the scan data of the original trailing
edge and that taken after the original is conveyed past the DP original scanning position. If dust
is identified, the DP original scanning position is adjusted for the following originals.
Purpose
When using DP, to solve the problem when black lines occurs due to the dust with respect to
original reading position.
Method
Display Description
CCD Setting of standard data when dust is detected.
Black Line Initialization of original reading position.
Setting: [CCD]
2. Change the value using the +/- or numeric keys.
Setting Initial
Display Description
range setting
R Lowest density of the R regard as the dust 0 to 255 125
G Lowest density of the G regard as the dust 0 to 255 125
B Lowest density of the B regard as the dust 0 to 255 125
Method: [Black Line]

1. Select [Clear].
2. Press the start key. The setting is cleared.
Completion
1-3-63
2LK/2LN/2LM/2LC

U089 Outputting a MIP-PG pattern
Description
Selects and outputs the MIP-PG pattern created in the machine.
Purpose
To check copier status other than scanner when adjusting image printing, using MIP-PG pattern
output (with-out scanning).
Method
2. Select the MIP-PG pattern to be output and press the start key.
Display Description Purpose
256Gradation 256-gradation PG To check the gradation reproducibility
Color Belt Four color belts PG To check the developer state and the
engine section ID
Gray(C) Cyan PG To check the drum quality
Gray(M) Magenta PG To check the drum quality
Gray(Y) Yellow PG To check the drum quality
Gray(K) Black PG To check the drum quality
White Blank paper PG To check the drum quality
Gradation Gray 5-graduation gray PG To check for vertical lines on the laser
scanner unit
Warranty Four color belts PG, Pattern output for LLU assurance
Cyan PG, Magenta PG, application
Yellow PG and Black PG
4. Press the start key. A MIP-PG pattern is output.
Completion
1-3-64
2LK/2LN/2LM/2LC

U091 Setting the white line correction
Description
Sets the error detection threshold value for white line correction and displays the count result of
abnormal pixels.
Purpose
To perform when replacing the CIS, DP main PWB or CIS roller.
Method
2. Select the item.
Display Description
Calculation(R) Abnormal pixel count result for color R
Calculation(G) Abnormal pixel count result for color G
Calculation(B) Abnormal pixel count result for color B
Threshold(R) Displaying of abnormal pixel detection threshold value for color R
Threshold(G) Displaying of abnormal pixel detection threshold value for color G
Threshold(B) Displaying of abnormal pixel detection threshold value for color B
Threshold Abnormal pixel threshold value setting
(Abnormal)
Mode Switching between white line correction mode ON/OFF
Execute Holding of white reference data
Method: white line correction

1. Press [Execute].
2. Press the start key. Holding of white reference data is started.
3. The count result of abnormal pixels is displayed.
5. Place a gray original on the DP with the gray side down. Load paper in the cassette.
The paper should be the same size as the original.
Two test pattern sheets will be printed. (1st sheet: blank sheet, 2nd sheet: Approx. 60 mm
black band)
7. If no vertical lines appear on either sheet, the setting has been completed normally.
If vertical black lines appear on the blank sheet and vertical white lines appear in the black
band in the same position, clean the CIS roller and the CIS glass and then repeat white line
correction.
If vertical black lines or vertical white lines appear on both sheets, white line correction has
been completed normally. However, the cause of the vertical lines lies in the engine, and thus
the engine must be checked.
1-3-65
2LK/2LN/2LM/2LC

U091 How to view test copies
blank sheet black band Causes Corrective measures
No lines No lines - Complete
Black lines White lines Dirty CIS roller or CIS Clean CIS roller or CIS glass
glass and then perform U091 again
Black lines No lines Engine side U091 ends, check engine
No lines White lines Engine side U091 ends, check engine
Setting: Threshold value setting

Setting Initial
Display Description
range setting
Threshold(R) Displaying of abnormal pixel detection 0 to 1023 112
threshold value for color R
Threshold(G) Displaying of abnormal pixel detection 0 to 1023 112
threshold value for color G
Threshold(B) Displaying of abnormal pixel detection 0 to 1023 112
threshold value for color B
Threshold Abnormal pixel threshold value setting 0 to 8191 75
(Abnormal)
Mode Switching between white line correction 0: OFF/ 0
mode ON/OFF 1: ON/
2: Test mode
* : Normally the Threshold (Com) value should not be changed from 112, the initial setting.
If white lines appear even though the CIS roller and glass are not dirty, raise the set value.
If fine lines in some originals disappear, lower the set value.
Set within the range 50 to 200. (If set outside this range, the image may be affected.)
Completion
1-3-66
2LK/2LN/2LM/2LC

U093 Adjusting the exposure density gradient
Description
Changes the exposure density gradient in the manual density mode, depending on respective
image quality modes.
Purpose
To set how the image density is altered by a change of one step in the manual density adjustment
for respective image quality modes. Also used to make copy images darker or lighter.
Method
2. Select the image quality mode.
Display Description
Text Density in the text mode
Mixed Density in the text and photo mode
Other Density in modes other than the text mode or the text and photo mode
Fax Text Density in the text in fax mode
Fax Photo Density in the photo in fax mode
Setting: [Text/Mixed/Other]
2. Change the setting value using the +/- or numeric keys.
Setting Initial
Display Description
range setting
F/C Darker Change in density when manual den- 0 to 3 0
sity is set dark (full color mode)
F/C Lighter Change in density when manual den- 0 to 3 0
sity is set light (full color mode)
B/W Darker Change in density when manual den- 0 to 3 0
sity is set dark (black/white mode)
B/W Lighter Change in density when manual den- 0 to 3 0
sity is set light (black/white mode)
Increasing the setting makes the change in density larger, and decreasing it makes the
change smaller.
1-3-67
2LK/2LN/2LM/2LC

U093 Setting: [Fax Text/Fax Photo]
Setting Initial
Display Description
range setting
Darker Gradient for darker setting 0 to 3 0
Lighter Gradient for lighter setting 0 to 3 0
Increasing the setting makes the change in density larger, and decreasing it makes the
change smaller.
Completion
U099 Adjusting original size detection
Description
Checks the operation of the original size sensor and sets the sensing threshold value.
Purpose
To adjust the sensitiveness of the sensor and size judgement time if the original size sensor mal-
functions frequently due to incident light or the like.
Method
2. Select the item.
Display Description
Data1 Displaying original size sensor transmission data
B/W Level1 B/W LEVEL setting original size sensor threshold value
Setting original size judgment time
Data2 Displaying original size sensor transmission data
(when DP is installed)
Method: [Data1/Data2]
1. Place the original and close the original cover or DP. The detection sensor transmission data
is displayed.
Display Description
Original Area R Detected original width size (R)
Original Area G Detected original width size (G)
Original Area B Detected original width size (B)
Original Area Detected original width size
Size SW L Displays the original size sensor (OSS) ON/OFF
1-3-68
2LK/2LN/2LM/2LC

U099 Setting: [B/W Level1]
1. Select an item to be set.
2. Change the setting value using the +/- keys or numeric keys.l
Setting Initial
Display Description
range setting
Original R1 - 3 Original threshold value for color R 0 to 255 50/50/50
Original G1 - 3 Original threshold value for color G 0 to 255 50/50/50
Original B1 - 3 Original threshold value for color B 0 to 255 50/50/50
Light Source R Light source threshold value for color R 0 to 255 49
Light Source G Light source threshold value for color G 0 to 255 49
Light Source B Light source threshold value for color B 0 to 255 49
Wait Time Time from activation of the original 0 to 255 150
detection switch (ODSW) to original
size judgment
A larger value increases the sensor sensitivity, and a smaller value decreases it.
Completion
Press the stop key. The screen for maintenance item No. is displayed.
1-3-69
2LK/2LN/2LM/2LC

U100 Adjusting main high voltage
Description
Controls the charger roller voltage to optimize the surface potential.
Purpose
To change the setting value to adjust the image if an image failure (background blur, etc.) occurs.
Method
2. Select an item and press the start key.
Display Description
Adj AC Bias Main charger AC bias for each color
Set AC Auto Adj Setting the AC bias auto adjustment
Set DC Bias Main charger DC bias for each color
Adj DC Bias Additional surface potential
Set Low Temp Pre-charge time at power supply ON
Set Charger Freq Setting the main charger frequency
Chk Current Rush current display
Setting: [Adj AC Bias]

Increasing the setting makes the image lighter; decreasing it makes the image darker.
The values set vary depending on environments.
Display Description Setting range
AC Bias(C) Main charger AC bias for cyan 0 to 255
AC Bias(M) Main charger AC bias for magenta 0 to 255
AC Bias(Y) Main charger AC bias for yellow 0 to 255
AC Bias(K) Main charger AC bias for black 0 to 255
AC Bias B/W(K) Main charger AC bias for black in black/white 0 to 255
mode
Setting: [Set AC Auto Adj]

Display Description
On Turns auto adjustment ON
Off Turns auto adjustment OFF
Initial setting: On
1-3-70
2LK/2LN/2LM/2LC

U100 Displaying: [Set DC Bias]
1. The current setting is displayed.
Display Description
DC1 Bias(C) Main charger DC bias for cyan (full speed)
DC1 Bias Half(C) Main charger DC bias for cyan (half speed)
DC1 Bias(M) Main charger DC bias for magenta (full speed)
DC1 Bias Half(M) Main charger DC bias for magenta (half speed)
DC1 Bias(Y) Main charger DC bias for yellow (full speed)
DC1 Bias Half(Y) Main charger DC bias for yellow (half speed)
DC1 Bias(K) Main charger DC bias for black (full speed)
DC1 Bias Half(K) Main charger DC bias for black (half speed)
DC1 Bias B/W(K) Main charger DC bias for black in black/white mode
Setting: [Adj DC Bias]

Increasing the setting makes the image lighter; decreasing it makes the image darker.l
Setting Initial
Display Description
range setting
DC2 Bias(C) Main charger DC bias for cyan (full speed) 128 to 127 0
DC2 Bias Half(C) Main charger DC bias for cyan (half speed) 128 to 127 0
DC2 Bias(M) Main charger DC bias for magenta 128 to 127 0
(full speed)
DC2 Bias Half(M) Main charger DC bias for magenta 128 to 127 0
(half speed)
DC2 Bias(Y) Main charger DC bias for yellow (full speed) 128 to 127 0
DC2 Bias Half(Y) Main charger DC bias for yellow (half speed) 128 to 127 0
DC2 Bias(K) Main charger DC bias for black (full speed) 128 to 127 0
DC2 Bias Half(K) Main charger DC bias for black (half speed) 128 to 127 0
DC2 Bias B/W(K) Main charger DC bias for black
in black/white mode
Setting: [Set Low Temp]

1. Change the value using the +/- or numeric keys.l
Setting Initial
Display Description
range setting
Set Low Temp Pre-charge time at power supply ON 0 to 6 1
1-3-71
2LK/2LN/2LM/2LC

U100 Setting: [Set Charger Freq]
Setting Initial
Display Description
range setting
Generally Main charger frequency 0 to 65535 1429*1/1333*2
B/W Main charger frequency in black/white mode 0 to 65535 28544
*1: 30 ppm/35 ppm/45 ppm model *2: 55 ppm model
Displaying: [Chk Current]

Display Description
C Cyan rush current
M Magenta rush current
Y Yellow rush current
K Black rush current
Supplement
Completion
Press the stop key. The screen for maintenance item No. is displayed.
1-3-72
2LK/2LN/2LM/2LC

U101 Setting the voltage for the primary transfer
Description
Sets the control voltage for the primary transfer.
Purpose
To change the setting when any density problems, such as too dark or light, occur.
Setting
Display Description
Normal Setting the primary transfer positive voltage
Add Color Setting the addition value
Add Color 2nd Setting the addition value for the second side
Surround Correct Environmental correction ON/OFF setting
Setting: [Normal]
Setting Initial
Display Description
range setting
Full Primary transfer positive voltage for yellow 0 to 255 116*1/123*2/132*2
(full speed)
Half Primary transfer positive voltage for yellow 0 to 255 109*1/115*2
(half speed)
3/4 Primary transfer positive voltage for yellow 0 to 255 158
at 3/4 times of line speed
*1: 30 ppm/35 ppm *2: 45 ppm model *3: 55 ppm model

Setting: [Add Color]

Setting Initial
Display Description
range setting
C Addition value (cyan) -127 to 127 3
M Addition value (magenta) -127 to 127 3
Y Addition value (black) -127 to 127 5
1-3-73
2LK/2LN/2LM/2LC

U101 Setting: [Add Color 2nd]
Setting Initial
Display Description
range setting
C Addition value for the second side (cyan) -127 to 127 0
M Addition value for the second side (magenta) -127 to 127 0
Y Addition value for the second side (yellow) -127 to 127 0
K Addition value for the second side (black) -127 to 127 0
Setting: [Surround Correct]

Display Description
On Environmental correction ON
Off Environmental correction OFF
Initial setting: On
Supplement
Completion
1-3-74
2LK/2LN/2LM/2LC

U106 Setting the voltage for the secondary transfer
Description
Sets the control voltage for the secondary transfer depending on each paper type.
Purpose
To change the setting when any density problems, such as too dark or light, occur.
Method
Display Description
Light/Normal1 Control voltage for the transfer bias on paper with thickness
60 g/m2 to 64 g/m2 and 60 g/m2 to 75 g/m2
Normal2/3 Control voltage for the transfer bias on paper with thickness
75 g/m2 to 105 g/m2
Heavy1 Control voltage for the transfer bias on paper with thickness
106 g/m2 to 135 g/m2
Heavy2-5 Control voltage for the transfer bias on paper with thickness
136 g/m2 to 300 g/m2
OHP Control voltage for the transfer bias for transparencies
Bias Transfer bias value
Setting: [Light/Normal1]
Display Description
1st Control voltage for the transfer bias for the first side (full speed)
2nd Control voltage for the transfer bias for the second side (full speed)
1st 3/4(Gloss) Control voltage for the transfer bias for the first side at 3/4 times of
line speed
2nd 3/4(Gloss) Control voltage for the transfer bias for the second side at 3/4 times
of line speed
1st B/W Control voltage for the transfer bias for the first side in black/white
mode
2nd B/W Control voltage for the transfer bias for the second side in black/white
mode
2. Select the paper width to be set.
Setting Initial setting

Display Description
range 30 ppm 35 ppm 45 ppm 55 ppm
Width=105 105 mm wide 0 to 255 153 140 153 166
Width=210 210 mm wide 0 to 255 153 140 153 166
Width=297 297 mm wide 0 to 255 153 140 153 166
1-3-75
2LK/2LN/2LM/2LC

U106 Setting: [Normal2/3]
Display Description
1st Control voltage for the transfer bias for the first side (full speed)
2nd Control voltage for the transfer bias for the second side (full speed)
1st 3/4(Gloss) Control voltage for the transfer bias for the first side at 3/4 times of
line speed
2nd 3/4(Gloss) Control voltage for the transfer bias for the second side at 3/4 times
of line speed
1st B/W Control voltage for the transfer bias for the first side in black/white
mode
2nd B/W Control voltage for the transfer bias for the second side in black/white
mode

Display Description
Width=105 105 mm wide 0 to 255 153 140 153 166
Width=210 210 mm wide 0 to 255 153 140 153 166
Width=297 297 mm wide 0 to 255 153 140 153 166
Setting: [Heavy1]
Display Description
1st 3/4 Control voltage for the transfer bias for the first side at 3/4 times of
line speed
2nd 3/4 Control voltage for the transfer bias for the second side at 3/4 times
of line speed

Display Description
Width=105 105 mm wide 0 to 255 153 140 153 166
Width=210 210 mm wide 0 to 255 153 140 153 166
Width=297 297 mm wide 0 to 255 153 140 153 166
1-3-76
2LK/2LN/2LM/2LC

U106 Setting: [Heavy2-5]
Display Description
1st Half Control voltage for the transfer bias for the first side (half speed)
2nd Half Control voltage for the transfer bias for the second side (half speed)

Display Description
Width=105 105 mm wide 0 to 255 153 140 153 166
Width=210 210 mm wide 0 to 255 153 140 153 166
Width=297 297 mm wide 0 to 255 153 140 153 166
Setting: [OHP]

Display Description
Width=105 105 mm wide 0 to 255 153 140 153 166
Width=210 210 mm wide 0 to 255 153 140 153 166
Width=297 297 mm wide 0 to 255 153 140 153 166
Setting: [Bias]
Setting Initial
Display Description
range setting
Reverse Transfer reverse bias (full speed) 0 to 255 42
Reverse Half Transfer reverse bias (hald speed) 0 to 255 42
Reverse 3/4 Transfer reverse bias at 3/4 times of line 0 to 255 42
speed
Reverse B/W Transfer reverse bias in black/white 0 to 255 42
mode
Cleaning Cleaning control value (full speed) 0 to 255 42
Cleaning Half Cleaning control value (half speed) 0 to 255 42
Cleaning 3/4 Cleaning control value at 3/4 times of 0 to 255 42
line speed
1-3-77
2LK/2LN/2LM/2LC

U106 Supplement
Completion
U107 Setting the transfer cleaning voltage
Description
Sets the cleaning control voltage for transfer belt unit.
Purpose
Change settings if an offset has occurred due to the failure of cleaning the transfer belt.
Method
Display Description
Belt(A) Transfer belt cleaning voltage (printing)
Belt(B) Transfer belt cleaning voltage (paper interval)

Display Description
Full Full speed 0 to 255 86 74 86 97
Half Half speed 0 to 255 86 74 86 97
3/4 0 to 255 86 74 86 97
B/W Black/white mode 0 to 255 86 74 86 97
Supplement
Completion
1-3-78
2LK/2LN/2LM/2LC

U108 Setting separation shift bias
Description
Adjusts output of separation shift bias and ON/OFF timing.
Purpose
To set when the separated malfunction of the paper occurs.
Method
Display Description
Output Adjusting the separation shift bias output
Output 3/4 Adjusting the separation shift bias output
Output B/W Adjusting the separation shift bias output in black/white mode
Timing Adjusting the ON/OFF timing with paper position
Setting: [Output]
2. Change the setting value using the +/- or numeric key.
Setting Initial
Display Description
range setting
Light 1st Separation shift bias for the first side on 0 to 255 21
paper with thickness 52 to 59 g/m2
Light 2nd Separation shift bias for the second side 0 to 255 21
on paper with thickness 52 to 59 g/m2
Normal 1st Separation shift bias for the first side on 0 to 255 21
Normal 2nd Separation shift bias for the second side 0 to 255 21
Add Normal Addition value for leading edge on paper -127 to 127 0
Lead with thickness 76 to 105 g/m2
Heavy/OHP Separation shift bias for transparencies 0 to 255 21
or paper with thickness 106 to 300 g/m2
1-3-79
2LK/2LN/2LM/2LC

U108 Setting: [Output 3/4 / Output B/W]
Setting Initial
Display Description
range setting
Light 1st Separation shift bias for the first side on 0 to 255 43
Light 2nd Separation shift bias for the second side 0 to 255 43
Normal 1st Separation shift bias for the first side on 0 to 255 43
Normal 2nd Separation shift bias for the second side 0 to 255 43
Setting: [Timing]
Setting Initial
Display Description
range setting
On Timing Lead Separation shift bias ON timing at lead- -200 to 200 0
ing edge of paper
On Timing Separation shift bias ON timing at center -200 to 200 0
Center of paper
Off Timing Separation shift bias OFF timing -200 to 200 0
Completion
1-3-80
2LK/2LN/2LM/2LC

U109 Checking the drum type
Description
Displays the drum sensitivity data.
Purpose
To check the drum sensitivity data.
Method
2. Select the item.
Display Description
Dark(C) Drum sensitivity data for cyan (dark potential)
Light(C) Drum sensitivity data for cyan (light potential)
Dark(M) Drum sensitivity data for magenta (dark potential)
Light(M) Drum sensitivity data for magenta (light potential)
Dark(Y) Drum sensitivity data for yellow (dark potential)
Light(Y) Drum sensitivity data for yellow (light potential)
Dark(K) Drum sensitivity data for black (dark potential)
Light(K) Drum sensitivity data for black (light potential)
The drum sensitivity data is displayed.
Display Description
DATA1 - DATA11 Drum sensitivity data
Completion
U110 Checking the drum count
Description
Displays the drum counts for checking.
Purpose
To check the drum status.
Method
1. Press the start key. The current drum counts is displayed.
Display Description
C Drum count value for cyan
M Drum count value for magenta
Y Drum count value for yellow
K Drum count value for black
Completion
1-3-81
2LK/2LN/2LM/2LC

U111 Checking the drum drive time
Description
Displays the drum drive time for checking a figure, which is used as a reference when correcting
the high voltage based on time.
Purpose
To check the drum status.
Method
1. Press the start key. The drum drive time is displayed.
Display Description
C Drum drive time for cyan
M Drum drive time for magenta
Y Drum drive time for yellow
K Drum drive time for black
Completion
U117 Checking the drum number
Description
Displays the drum number.
Purpose
To check the drum number.
Method
1. Press the start key. The drum number is displayed.
Display Description
C Cyan drum number
M Magenta drum number
Y Yellow drum number
K Black drum number
Completion
1-3-82
2LK/2LN/2LM/2LC

U118 Displaying the drum history
Description
Displays the past record of machine number and the drum counter.
Purpose
To check the count value of machine number and the drum counter.
Method
2. Select the color to check.
Display Description
C Cyan drum past record
M Magenta drum past record
Y Yellow drum past record
K Black drum past record
The history of a machine number and a drum counter for each color is displayed by three
cases.
Display Description
Machine History1 - 3 Historical records of the machine number
Cnt History1 - 3 Historical records of drum counter
Completion
U119 Setting the drum
Description
Sets drum sensitivity.
Purpose
To set the drum after replacing the drum unit or laser scanner unit.
Method
3. Press the start key. Drum setup is commenced.
1-3-83
2LK/2LN/2LM/2LC

U122 Checking the transfer belt unit number
Description
Displays the number of the transfer belt unit for checking.
Purpose
To check the number of the transfer belt.
Method
The current number of the transfer belt is displayed.
Completion
U123 Displaying the transfer belt unit history
Description
Displays the past record of machine number and the transfer belt unit counter.
Purpose
To check the count value of machine number and the transfer counter.
Method
The history of a machine number and a transfer belt unit counter for each color is displayed
by three cases.
Display Description
Cnt History1 - 3 Historical records of transfer belt unit counter
Completion
1-3-84
2LK/2LN/2LM/2LC

U124 Checking/clearing the transfer drive time
Description
Displays and clears the counts of the transfer drive time.
Purpose
To check the drive time after replacement of the transfer belt unit or transfer roller. Also to clear
the counts after replacing transfer roller.
Method
1. Press the start key. The current counts of the transfer drive time is displayed.
Display Description
Mid Trans Transfer belt unit drive time
2nd Trans Transfer roller drive time
Clearing
1. Select [Clear].
2. Press the start key. The drive time is cleared.
Clears only the transfer roller drive time. The transfer belt unit drive time is not cleared.
Completion
U127 Checking/clearing the transfer count
Description
Displays and clears the counts of the transfer counter.
Purpose
To check the count after replacement of the transfer belt unit or transfer roller. Also to clear the
counts after replacing transfer roller.
Method
1. Press the start key. The current counts of the transfer counter is displayed.
Display Description
Mid Trans Transfer belt unit count value
2nd Trans Transfer roller count value
Clearing
1. Select [Clear].
2. Press the start key. The counter value is cleared.
Clears only the transfer roller count value. The transfer belt unit count value is not cleared.
Completion
1-3-85
2LK/2LN/2LM/2LC

U128 Setting transfer high-voltage timing
Description
Adjusts the ON/OFF timing of transfer high-voltage output.
Purpose
Basically, the setting need not be changed. If any problem such as faulty images or dirt on the
back surface occurs, change the setting.
Method
2. Select the item to set.
3. Change the value using the +/- keys or numeric keys.
Setting Initial
Display Description
range setting
On Timing 1st Transfer ON timing adjustment value -200 to 200 -54
(first side)
On Timing 2nd Transfer ON timing adjustment value -200 to 200 -54
(second side)
Off Timing Transfer OFF timing adjustment value -200 to 200 10
Completion
U130 Toner installation
Description
Replenishes toner to the developer unit to a certain level from the toner container that has been
installed.
Purpose
To operate when installing the machine or replacing the developer unit.
Method
Toner installation is started and the control value of the toner sensor is displayed.
Display Description
C Toner sensor C control voltage
M Toner sensor M control voltage
Y Toner sensor Y control voltage
K Toner sensor K control voltage
Completion
1-3-86
2LK/2LN/2LM/2LC

U131 Adjusting the toner sensor control voltage
Description
Adjusts the toner sensor control voltage.
Purpose
If control values are not correctly retrievable due to the EEPROM of the developer unit failure,
etc., use manual adjustment and obtain a temporary control value.
Method
2. Select the item to be set or displayed.
Display Description
Manual Toner sensor control voltage manual adjustment
Auto Toner sensor control voltage auto adjustment
Mode Switching the manual adjustment and auto adjustment
Setting: [Manual]
Setting Initial
Display Description
range setting
Control(C) Toner sensor C control voltage 0 to 255 116
Control(M) Toner sensor M control voltage 0 to 255 116
Control(Y) Toner sensor Y control voltage 0 to 255 116
Control(K) Toner sensor K control voltage 0 to 255 116
Displaying: [Auto]
Display Description
Default(C) Reference value for toner sensor C control voltage
Default(M) Reference value for toner sensor M control voltage
Default(Y) Reference value for toner sensor Y control voltage
Default(K) Reference value for toner sensor K control voltage
Control(C) Toner sensor C control voltage after correction
Control(M) Toner sensor M control voltage after correction
Control(Y) Toner sensor Y control voltage after correction
Control(K) Toner sensor K control voltage after correction
1-3-87
2LK/2LN/2LM/2LC

U131 Setting: [Mode]
Display Description
Manual Toner sensor control voltage manual adjustment
Auto Toner sensor control voltage auto adjustment
Initial setting: Auto
Completion
U132 Replenishing toner forcibly
Description
Replenishes toner forcibly until the toner sensor output value reaches the toner feed start level.
Purpose
Used when the toner empty is detected frequently.
Method
Toner is replenished until the toner sensor output value reaches the toner feed start level.
Display Description
Supply(C) Toner feed start level (cyan)
Supply(M) Toner feed start level (magenta)
Supply(Y) Toner feed start level (yellow)
Supply(K) Toner feed start level (black)
Sensor(C) Toner sensor output value (cyan)
Sensor(M) Toner sensor output value (magenta)
Sensor(Y) Toner sensor output value (yellow)
Sensor(K) Toner sensor output value (black)
Completion
1-3-88
2LK/2LN/2LM/2LC

U135 Checking toner motor operation
Description
Drives toner motors.
Purpose
To check the operation of toner motors.
Remarks
When driving the toner motors long time or several times, developer section becomes the toner
full and is locked.
Method
2. Select [Toner].
Display Description
Toner Toner motor (TM) is turned on
4. To stop the operation, press the stop key.
Completion
Press the stop key after operation stops. The screen for selecting a maintenance item No. is dis-
played.
U136 Setting toner near end detection
Description
Sets the level that indicates the number of sheets that can be printed from occurrence of toner
near end to toner empty.
Purpose
To change the setting to advance detection of near end if the interval from toner near end to toner
empty seems too short.
Setting
Setting Initial
Display Description
range setting
CMY Setting the level of cyan/magenta/yellow toner 0 to 9 3
K Setting the level of black toner 0 to 9 3
Increasing the setting makes the interval from toner near end to toner empty longer.
Decreasing the setting makes the interval from toner near end to toner empty shorter.
If 0 is set, toner near end will not be detected.
Completion
1-3-89
2LK/2LN/2LM/2LC

U139 Displaying the temperature and humidity outside the machine
Description
Displays the detected temperature and humidity outside the machine.
Purpose
To check the temperature and humidity outside the machine.
Method
2. Select the item.
Display Description
Ext/Int Internal/External temperature (°C), External humidity (%)
LSU Internal temperature around the laser scanner unit (°C)
Developing Internal temperature around the developer section (°C)
Method: [Ext/Int]
1. The current temperature and humidity are displayed.
Display Description
External Temp External temperature (°C)
External Humidity External humidity (%)
Internal Temp Internal temperature (°C)
Method: [LSU]
1. The current temperature is displayed.
Display Description
C Internal temperature around the laser scanner unit C (°C)
M Internal temperature around the laser scanner unit M (°C)
Y Internal temperature around the laser scanner unit Y (°C)
K Internal temperature around the laser scanner unit K (°C)
Method: [Developing]
1. The current temperature is displayed.
Display Description
C Internal temperature around the developer unit C (°C)
M Internal temperature around the developer unit M (°C)
Y Internal temperature around the developer unit Y (°C)
K Internal temperature around the developer unit K (°C)
Completion
1-3-90
2LK/2LN/2LM/2LC

U140 Displaying developer bias
Description
Displays and changes various developer bias value.
Purpose
To check or changes the developer bias value.
Method
Display Description
Sleeve DC Developer sleeve roller DC bias
Sleeve AC Developer sleeve roller AC bias
Mag DC Developer magnet roller DC bias
Mag AC Developer magnet roller AC bias
Sleeve Freq Developer sleeve roller frequency
Sleeve Duty Developer sleeve roller duty
Mag Duty Developer magnet roller duty
AC Calib Executing or setting the AC calibration
(45 ppm model/55 ppm model only)
Setting: [Sleeve DC]

Initial
Setting setting
Display Description
range 30 ppm/ 45 ppm/
35 ppm 55 ppm
C Developer sleeve roller DC bias for cyan 0 to 255 62 70
M Developer sleeve roller DC bias for 0 to 255 62 70
magenta
Y Developer sleeve roller DC bias for 0 to 255 62 70
yellow
K Developer sleeve roller DC bias for 0 to 255 62 70
black
B/W Developer sleeve roller DC bias in black/ 0 to 255 70 70
white mode
1-3-91
2LK/2LN/2LM/2LC

U140 Setting: [Sleeve AC]
Initial
Setting setting
Display Description
35 ppm 55 ppm
C Developer sleeve roller AC bias for cyan 0 to 255 159 155
M Developer sleeve roller AC bias for 0 to 255 159 155
magenta
Y Developer sleeve roller AC bias for 0 to 255 159 155
yellow
K Developer sleeve roller AC bias for black 0 to 255 159 155
B/W Developer sleeve roller AC bias in black/ 0 to 255 155 155
white mode
Setting: [Mag DC]

Initial
Setting setting
Display Description
35 ppm 55 ppm
C Developer magnet roller DC bias for 0 to 255 130 155
cyan
M Developer magnet roller DC bias for 0 to 255 130 155
magenta
Y Developer magnet roller DC bias for 0 to 255 130 155
yellow
K Developer magnet roller DC bias for 0 to 255 130 155
black
B/W Developer magnet roller DC bias in 0 to 255 155 155
black/white mode
1-3-92
2LK/2LN/2LM/2LC

U140 Setting: [Mag AC]
Initial
Setting setting
Display Description
35 ppm 55 ppm
C Developer magnet roller AC bias for 0 to 255 101 178
cyan
M Developer magnet roller AC bias for 0 to 255 101 178
magenta
Y Developer magnet roller AC bias for 0 to 255 101 178
yellow
K Developer magnet roller AC bias for 0 to 255 101 178
black
B/W Developer magnet roller AC bias in 0 to 255 178 178
black/white mode
Setting: [Sleeve Freq]

Setting Initial
Display Description
range setting
Normal Developer sleeve roller frequency 0 to 6200 5276
B/W Developer sleeve roller frequency in 0 to 6200 5344
black/white mode
Half Developer sleeve roller frequency (half speed) 0 to 6200 5276
3/4 Developer sleeve roller frequency at 3/4 times 0 to 6200 5276
of line speed
Setting: [Sleeve Duty]

Initial
Setting setting
Display Description
35 ppm 55 ppm
Normal Developer sleeve roller duty 0 to 99 37 68
B/W Developer sleeve roller duty in black/ 0 to 99 68 68
white mode
1-3-93
2LK/2LN/2LM/2LC

U140 Setting: [Mag Duty]
Initial
Setting setting
Display Description
35 ppm 55 ppm
Normal Developer magnet roller duty 0 to 99 63 43
B/W Developer magnet roller duty in black/ 0 to 99 43 43
white mode
Method: [AC Calib]

1. Select the item.
Display Description
Calibration Executing the AC calibration
Magnification AC calibration target bias value setting
Type Mode setting for AC calibration bias control
Method: [Calibration]
1. Turns the items to implement to on.
If the machine is installed at high altitude, select [High Altitude].
Display Description
C Developer unit C or drum unit C
M Developer unit M or drum unit M
Y Developer unit Y or drum unit Y
K Developer unit K or drum unit K
High Altitude Overall setting for installation at high altitude
3. Press the start key. AC calibration is executed.
* : When an error occurs, an error code is displayed.
1-3-94
2LK/2LN/2LM/2LC

U140 Setting: [Magnification]
Setting Initial
Display Description
range setting
C Target bias value (cyan) -10 to 5 0
M Target bias value (magenta) -10 to 5 0
Y Target bias value (yellow) -10 to 5 0
K Target bias value (black) -10 to 5 0
Method: [Type]
1. Select Mode1 or Mode2.
Display Description
Mode1 Execute AC calibration by normal bias control
Mode2 If print density is low in an installation at high altitude, execute
calibration by fixing the bias potential.
Completion
U148 Setting drum refresh mode
Description
Selects the mode used in drum refreshing
Purpose
Change settings when drum refreshing is too frequently executed.
Setting
2. Select the mode.
Setting Initial
Display Description
range setting
Mode Setting drum refresh mode 0 to 3 2
* : 0: Off / 1: Short / 2: Standard / 3: Long
Completion
1-3-95
2LK/2LN/2LM/2LC

U150 Checking sensors for toner
Description
Displays the toner sensor output value.
Purpose
To check the output value for each color when any image problems occur.
Method
2. Select the item to be display.
Display Description
Waste Toner Control voltage value of the waste toner sensor
Toner Control voltage value and replenishment level of toner sensor
each color
Method: [Waste Toner]

1. Check the status of sensor. The current value is displayed.
Display Description
Full Waste toner sensor 1 (WTS1)
Near Full Waste toner sensor 2 (WTS2)
Method: [Toner]
1. Check the status of sensor. The current value is displayed.
Display Description
Sensor(C) Toner sensor C output value
Sensor(M) Toner sensor M output value
Sensor(Y) Toner sensor Y output value
Sensor(K) Toner sensor K output value
Supply(C) Toner replenishment level for cyan
Supply(M) Toner replenishment level for magenta
Supply(Y) Toner replenishment level for yellow
Supply(K) Toner replenishment level for black
Completion
1-3-96
2LK/2LN/2LM/2LC

U156 Setting the toner replenishment level
Description
Sets the toner replenishment level for each color.
Purpose
To change settings according to the original image.
Method
Display Description
Supply Setting the toner replenishment level
Empty Setting the toner empty level
Method: [Supply]
Setting Initial
Display Description
range setting
C Toner replenishment level for cyan 0 to 900 775
M Toner replenishment level for magenta 0 to 900 775
Y Toner replenishment level for yellow 0 to 900 775
K Toner replenishment level for black 0 to 900 775
Method: [Empty]
Setting Initial
Display Description
range setting
C Toner empty level for cyan 0 to 1023 100
M Toner empty level for magenta 0 to 1023 100
Y Toner empty level for yellow 0 to 1023 100
K Toner empty level for black 0 to 1023 100
Completion
1-3-97
2LK/2LN/2LM/2LC

U157 Checking the developer drive time
Description
Displays the developer drive time for checking a figure, which is used as a reference when cor-
recting the toner control.
Purpose
To check the developer drive time after replacing the developer unit.
Method
1. Press the start key. The developer drive time is displayed.
Display Description
C Developer drive time for cyan
M Developer drive time for magenta
Y Developer drive time for yellow
K Developer drive time for black
Completion
U158 Checking the developer count
Description
Displays the developer count for checking.
Purpose
To check the developer unit status.
Method
1. Press the start key. The current developer counts is displayed.
Display Description
C Developer count value for cyan
M Developer count value for magenta
Y Developer count value for yellow
K Developer count value for black
Completion
1-3-98
2LK/2LN/2LM/2LC

U161 Setting the fuser control temperature
Description
Changes the fuser control temperature.
Purpose
Normally no change is necessary. However, can be used to prevent curling or creasing of paper,
or solve a fuser problem on thick paper.
Method
Display Description
Warm Up Control temperature except at printing
Print Control temperature during printing
Setting: [Warm Up]

Setting Initial
Display Description
range setting
Ready(Center) Control temperature at displaying 130 to 200(°C) 165
Ready (Center)
Ready(Edge) Control temperature at displaying 100 to 200(°C) 1
Ready (Edge)
Ready(Press) Control temperature at displaying 0 to 200(°C) 90
Ready (Press)
Drive(Center) Stable temperature during driving 130 to 200(°C) 175
(Center)
Wait(Center) Stable temperature during halt 130 to 200(°C) 165
(Center)
Low Power Control temperature at low power 0 to 200(°C) 150
(Press) consumption (Press)
High Speed Full speed shift temperature (Center) 0 to 200(°C) 160
(Center)
Pressure Pressurizing beginning temperature 130 to 200(°C) 50
(Press) (Press)
1-3-99
2LK/2LN/2LM/2LC

U161 Setting: [Print]
Setting Initial
Display Description
range setting
Full Speed Temperature at maximum print speed 130 to 200(°C) 165
(Center) (Center)
Duplex Shift Temperature at duplex printing 100 to 200(°C) 1
(Center) (Center)
Completion
U163 Resetting the fuser problem data
Description
Resets the detection of a service call code indicating a problem in the fuser section.
Purpose
To prevent accidents due to an abnormally high fuser temperature.
Method
2. Press [Execute].
3. Press the start key. The fuser problem data is initialized.
U167 Checking/clearing the fuser count
Description
Displays and clears the fuser count for checking.
Purpose
To check or clear the fuser count after replacement of the fuser unit. Also to clear the counts after
replacing unit.
Method
1. Press the start key. The fuser count is displayed.
Display Description
Cnt Fuser unit count value
Clearing
1. Press [Clear].
2. Press the start key. The count is cleared.
Completion
1-3-100
2LK/2LN/2LM/2LC

U168 Checking/clearing the fuser drive time
Description
Displays or clears the fuser drive time.
Purpose
To check the fuser drive time after replacing the fuser unit.
Method
1. Press the start key. The fuser drive time is displayed.
Display Description
Press Fuser unit drive time (press)
Release Fuser unit drive time (release)
Clearing
1. Press [Clear].
2. Press the start key. The drive time is cleared.
Completion
U169 Checking/setting the fuser power source
Description
Displays and settings the specification of fuser power supply for checking.
Purpose
To check or set the specification of fuser power supply after replacement of the fuser unit.
Method
2. Select the mode.
Mode Specification of fuser power supply 1 to 3
1: 100 V specifications 2: 200 V specifications 3: 120 V specifications
Completion
1-3-101
2LK/2LN/2LM/2LC

U199 Displaying fuser heater temperature
Description
Displays the detected fuser temperature.
Purpose
To check the fuser temperature.
Method
1. Press the start key. The fuser temperature is displayed.
Display Description
Heat Roller Edge1 Heat roller edge temperature (°C)
Heat Roller Edge2 Heat roller edge temperature (°C)
Heat Roller Center Heat roller center temperature (°C)
Press Roller Center Press roller center temperature (°C)
Completion
Press the stop key. The screen for selecting a maintenance mode No. is displayed.
U200 Turning all LEDs on
Description
Turns all the LEDs on the operation panel on.
Purpose
To check if all the LEDs on the operation panel light.
Method
3. Press the start key.All the LEDs on the operation panel light.
4. Press the stop key. The LEDs turns off.
Completion
1-3-102
2LK/2LN/2LM/2LC

U201 Initializing the touch panel
Description
Automatically correct the positions of the X- and Y-axes of the touch panel.
Purpose
To automatically correct the display positions on the touch panel after it is replaced.
Method
2. Select the [Initialize] or [Check].
Display Description
Initialize Adjusts the display on the panel automatically
Check Checks the display on the touch panel
Method: [Initialize]
2. Press the center of the + keys. Be sure to press three + keys displayed in order.
The touch panel is adjusted automatically.
3. Press the indicated three + keys, and then check the display.
4. Press the stop key.
Method: [Check]
2. Press the indicated three + keys, and then check the display.
When adjusting the display, press [Initialize] to execute the adjustment automatically.
3. Press the stop key.
Completion
1-3-103
2LK/2LN/2LM/2LC

U202 Setting the KMAS host monitoring system
Description
Initializes or operates the KMAS host monitoring system.
This is an optional device which is currently supported only by Japanese specification machines,
so no setting is necessary.
Purpose
Performed at installation, periodic maintenance, and/or repair.
Method
2. Select the item.
Display Description
Init/Set TEL No. Initialization/Phone Nbr. se
Call Service End Outgoing at the end of service activities
Method: [Init/Set TEL No.]

1. Select the item to be input.
Display Description
TEL No. 1 Sales companies
TEL No. 2 Call center
2. Input the telephone number using the numeric keys.
4. Select [Initialize].
6. Press the start key. Communication with the host initiated.
7. The result of communication will be displayed. (Refer to the result.)
Method: [Call Service End]

2. Press the start key. Communication with the host initiated.
3. The result of communication will be displayed. (Refer to the result.)
Result table
Display Description
OK Communication properly terminated.
Communication error (Nbr. of calls exceeded)
Communication error (Communication timeout)
NG Communication error (Communication trial timeout)
Communication error (Other)
KMAS unreachable
Completion
1-3-104
2LK/2LN/2LM/2LC

U203 Checking DP operation
Description
Simulates the original conveying operation separately in the DP.
Purpose
To check the DP operation.
Method
2. Place an original in the DP if running this simulation with paper.
3. Select the speed to be operated.
Display Description
Normal Speed Normal reading (600 dpi)
High Speed High-speed reading
Display Description
CCD ADP (Non-P) Without paper, single-sided original of CCD
(continuous operation)
CCD ADP With paper, single-sided original of CCD
CCD RADP (Non-P) Without paper, double-sided original of CCD
CCD RADP With paper, double-sided original of CCD
CIS (Non-P) Without paper, double-sided original of CIS
CIS With paper, double-sided original of CIS
6. To stop continuous operation, press the stop key.
Completion
1-3-105
2LK/2LN/2LM/2LC

U204 Setting the presence or absence of a key card or key counter
Description
Sets the presence or absence of the optional key card or key counter.
Purpose
To run this maintenance item if a key card or key counter is installed.
Method
Display Description
Device Sets the presence or absence of the key card or key counter
Message Sets the message when optional equipment is not installed
Setting: [Device]
1. Select the optional counter to be installed.
Display Description
Key-Card The key card is installed
Key-Counter The key counter is installed
Off Not installed
Initial setting: Off
Setting: [MESSAGE]
1. Select the [Key Device] or [Coin Vender].
Supplement
Two or more Key cards, key counters, and coin venders cannot be installed simultaneously.
Therefore, if any of these options are chosen, coin vender settings U206 will be automatically
cancelled (Off).
1-3-106
2LK/2LN/2LM/2LC

U206 Setting the presence or absence of a coin vender
Description
Sets the presence or absence of the optional coin vender.
This is an optional device which is currently supported only by Japanese specification machines.
Purpose
To run this maintenance item if a coin vender is installed.
Method
Display Description
On/Off Config Sets the presence or absence of the coin vender
No Coin Action Behavior when change runs out during copying
Price Charge per copy by size and color
Setting: [On/Off Config]

Display Description
On The coin vender is installed
Off The coin vender is not installed
Setting: [No Coin Action]

1. Select the item.
Display Description
All Clear All clear is performed
Auto Clear Auto clear is performed
Off Clear is not performed
1-3-107
2LK/2LN/2LM/2LC

U206 Setting: [Price]
Display Description
B/W Black & White
CMY Single color C, M, Y
RGB Single color R, G, B
Full Color Full color
2. Select the paper size to be set.
Initial
Setting setting
Display Description
range B/W CMY/RGB
Full Color
A3-Ledger A3/Ledger size 0 to 300 10 100
B4 B4 size 0 to 300 10 50
Card Post card 0 to 300 10 30
Other Other 0 to 300 10 50
In 10-yen inrements
Value of 0 allows non-restricted copying. (At a periodic maintenance, etc.)
U207 Checking the operation panel keys
Description
Checks operation of the operation panel keys.
Purpose
To check operation of all the keys and LEDs on the operation panel.
Method
1. Press the start key. The screen for executing is displayed.
2. [Count0] is displayed and the left most LED on the operation panel lights.
3. As the keys lined up in the same line as the lit indicator are pressed in the order from the top
to the bottom, the figure shown on the touch panel increases in increments of 1. When all the
keys in that line are pressed and if there are any LEDs corresponding to the keys in the line
on the immediate right, the top LED in that line will light.
4. When all the keys on the operation panel have been pressed, all the LEDs light for up to 10
seconds.
Completion
1-3-108
2LK/2LN/2LM/2LC

U208 Setting the paper size for the side feeder
Description
Sets the size of paper used in side feeder.
Purpose
To change the setting when installing the side feeder or the size of paper used in the side feeder
is changed.
Setting
2. Select the paper size (A4, B5 or Letter).
Initial setting: Letter (Inch specifications)
A4 (Metric specifications)
U211 Setting the presence or absence of the job separator
Description
Sets the presence or absence of the inner job separator.
Purpose
To run this maintenance item if the inner job separator is installed.
Method
2. Select [Inner Job Separator].
Display Description
On The inner job separator is installed
Off The inner job separator is not installed
1-3-109
2LK/2LN/2LM/2LC

U221 Setting the USB host lock function
Description
Specifies ON/OFF the USB host lock function. Setting this to ON causes the machine to be
unable to recognize the device connected to the USB host.
Purpose
Set according to the preference of the user.
Method
2. Select [Host Lock].
Display Description
On USB host lock function ON
Off USB host lock function OFF
Completion
U222 Setting the IC card type
Description
Sets the type of IC card.
Purpose
To change the type of IC card.
Setting
2. Select the item.
Display Description
Other The type of IC card is SSFC.
SSFC The type of IC card is not SSFC.
Initial setting: Other
Completion
1-3-110
2LK/2LN/2LM/2LC

U223 Operation panel lock
Description
Sets the operation panel lock function to ON or OFF.
Purpose
To restrict operation in the system menu on the operation panel.
Setting
2. Select the item.
Display Description
Unlock Release the lock of the operation from the system menu
Partial Lock Partially lock the operation from the system menu
Lock Entirely lock the operation from the system menu
Initial setting: Unlock
Completion
1-3-111
2LK/2LN/2LM/2LC

U224 Panel sheet extension
Description
Changes the image data and the message of the opening screen at the machine startup and the
image data and the message of the service call screen to user specified data.
Purpose
Set according to the preference of the user.
Setting
1. Write the image data or the message data to the USB memory.
2. Insert USB memory in USB memory slot of the machine.
4. Enter the maintenance item.
6. Select the [Install] or [UnInstall].
Display Description
Install Installs the image data or the message data
UnInstall Restores the original image data or message data
7. Select the item.
Display Description
Opening Img Startup screen image
Call Img Service call screen image
Call Msg Top Service call screen message
Call Msg Detail Service call screen detail message
8. Press the start key. Installation or uninstallation is started.
9. When normally completed, [OK] is displayed.
Completion
1-3-112
2LK/2LN/2LM/2LC

U234 Setting punch destination
Description
Sets the destination of punch unit of 1000-sheet finisher or 4000-sheet finisher.
Purpose
To be set when installing a different punch unit from the destination of the machine.
Setting
2. Select the destination.
Display Description
Auto Conforms to destination settings.
Japan Metric Metric (Japan) specifications
Inch Inch (North America) specifications
Europe Metric Metric (Europe) specifications
Sweden Sweden specifications
Initial setting: Inch (Inch specifications)/Europe Metric (Metric specifications)
1-3-113
2LK/2LN/2LM/2LC

U237 Setting finisher stack quantity
Description
Sets the number of sheets of each stack on the main tray and on the middle tray in 4000-sheet
finisher.
Purpose
To change the setting when a stack malfunction has occurred.
Method
Display Description
Main Tray Number of sheets of stack on the main tray
Middle Tray Number of sheets of stack on the middle tray for staple mode
Setting: [Main Tray]

Display Description
0 Number of sheets of stack on the main tray: 4000 sheets
1 Number of sheets of stack on the main tray: 1500 sheets
Initial setting: 0
Setting: [Middle Tray]

Display Description
0 Number of sheets of stack on the middle tray for staple mode:
50 sheets
1 Number of sheets of stack on the middle tray for staple mode:
30 sheets
Initial setting: 0
Number of sheets of stack on the internal tray for non-staple copying: 10 sheets
1-3-114
2LK/2LN/2LM/2LC

U240 Checking the operation of the finisher
Description
Turns each motor and solenoid of 1000-sheet finisher or 4000-sheet finisher ON.
Purpose
To check the operation of each motor and solenoid of the 1000-sheet finisher or 4000-sheet fin-
isher.
Method
2. Select the item to be checked.
Display Description
Motor Checking the motor of the document finisher
Solenoid Checking the solenoid of the document finisher
Mail Box Checking the motor of the mailbox
Booklet Checking the motor of the center-folding unit
Method: [Motor]
Display Description
Feed In(H) DF paper entry motor (DFPEM) is turned on at high speed
Feed In(L) DF paper entry motor (DFPEM) is turned on at low speed
Middle(H) DF middle motor (DFMM) is turned on at high speed
Middle(L) DF middle motor (DFMM) is turned on at low speed
Eject(H) DF eject motor (DFEM) is turned on at high speed
Eject(L) DF eject motor (DFEM) is turned on at low speed
Save(H) DF drum motor (DFDRM) is turned on at high speed
Save(L) DF drum motor (DFDRM) is turned on at low speed
Tray DF tray motor (DFTM) is turned on
Staple Move DF slide motor (DFSLM) is turned on
Staple DF staple motor (DFSTM) is turned on
Width Test(A3) DF side registration motor 1, 2 (DFSRM1, 2) is turned on
Width Test(LD) DF side registration motor 1, 2 (DFSRM1, 2) is turned on
Beat DF paddle motor (DFPDM) is turned on
Eject Unlock(HP) DF eject release motor (DFERM) is turned on to home position
Sort Test DF shift motor 1, 2 (DFSFM1, 2) is turned on
Eject Unlock(30) DF eject release motor (DFERM) drive position 30-sheet stack
Eject Unlock(50) DF eject release motor (DFERM) drive position 50-sheet stack
Eject Unlock(Fix) DF eject release motor (DFERM) fixed drive position
1-3-115
2LK/2LN/2LM/2LC

U240
Display Description
Eject Unlock(Full) DF eject release motor (DFERM) full-open drive position
Punch Punch motor (PUM) is turned on
Punch Move Punch slide motor (PUSLM) is turned on
Method: [Solenoid]
Display Description
Sub Tray DF feedshift solenoid (DFFSSOL) is turned on
Save Drum DF drum solenoid (DFDRSOL) is turned on
Booklet DF center fold solenoid (DFCFSOL) is turned on
Punch Punch solenoid (PUSOL) is turned on
Three Fold CF feedshift solenoid (CFFSSOL) is turned on
Method: [Mail Box]

Display Description
Conv Mailbox drive motor (MBDM) is turned on at paper conveying
Branch Mailbox drive motor (MBDM) is turned on at feedshift operation
Method: [Booklet]
Display Description
Folding CF main motor (CFMM) is turned on
Blade CF blade motor (CFBM) is turned on
Bundle Up CF adjustment motor 2 (CFADM2) is turned on
Bundle Down CF adjustment motor 1 (CFADM1) is turned on
Staple CF staple motor (CFSTM) is turned on
Width Test(A3) CF side registration motor 1, 2 (CFSRM1, 2) is turned on
Width Test(LD) CF side registration motor 1, 2 (CFSRM1, 2) is turned on
Feed In CF paper entry motor (CFPEM) is turned on
Completion
1-3-116
2LK/2LN/2LM/2LC

U241 Checking the operation of the switches of the finisher
Description
Displays the status of each switches and sensors of 1000-sheet finisher or 4000-sheet finisher.
Purpose
To check the operation of each switches and sensors of the 1000-sheet finisher or 4000-sheet
finisher.
Method
2. Select the item to be checked.
Display Description
Finisher Checking the switch and sensor of the document finisher
Mail Box Checking the switch and sensor of the mailbox
Booklet Checking the switch and sensor of the center-folding unit
Punch Checking the switch and sensor of the punch unit
Method: [Finisher]
reverse.
Display Description
Front Cover DF front cover switch (DFFCSW)
MPT
Top Cover DF top cover switch (DFTCSW)
Tray U-Limit DF tray upper limit sensor (DFTULS)
Tray HP2
Tray Middle DF tray middle sensor (DFTMS)
Tray L-Limit DF tray upper limit sensor (DFTLLS)
Tray L-Limit(BL) DF tray center hold sensor (DFTCFS)
Tray Top DF tray upper surface sensor (DFTUSS)
HP DF paper entry sensor (DFPES)
Sub Tray Eject DF sub eject sensor (DFSES)
Middle Tray Eject DF middle eject sensor (DFMES)
Drum DF drum sensor (DFDRS)
Staple HP DF slide sensor (DFSLS)
Middle Tray DF middle tray sensor (DFMTS)
Width Front HP DF side registration sensor 1 (DFSRS1)
Width Tail HP DF side registration sensor 2 (DFSRS2)
Bundle Eject HP DF bundle discharge sensor (DFBDS)
1-3-117
2LK/2LN/2LM/2LC

U241
Display Description
Match Paddle DF adjustment sensor (DFADS)
Lead Paddle DF paddle sensor (DFPDS)
Shift Front HP DF shift sensor 1 (DFSFS1)
Shift Tail HP DF shift sensor 2 (DFSFS2)
Shift Unlock HP DF shift release sensor (DFSFRS)
Sub Tray Full DF sub tray full sensor (DFSTFS)
Shift Set DF shift set sensor (DFSFSS)
Method: [Mail Box]

reverse.
Display Description
Eject MB eject sensor (MBES)
Cover MB cover open/close switch (MBCOCSW)
Over Flow1 MB overflow sensor 1 (MBOFS1)
Motor HP MB paper entry sensor (MBPES)
1-3-118
2LK/2LN/2LM/2LC

U241 Method: [Booklet]
reverse.
Display Description
HP CF paper entry sensor (CFPES)
Eject CF eject sensor (CFES)
Paper CF paper sensor (CFPS)
Tray Full CF tray full sensor (CFTFS)
Bundle Up HP CF adjustment sensor 1 (CFADS1)
Bundle Down HP CF adjustment sensor 2 (CFADS2)
Width Up HP CF side registration sensor 1 (CFSRS1)
Width Down HP CF side registration sensor 2 (CFSRS2)
Blade HP CF blade sensor (CFBLS)
Tray CF tray switch (CFTSW)
Set CF set switch (CFSSW)
Left Guide CF left guide switch (CFLGSW)
Vertical Feed CF paper conveying sensor (CFPCS)
Method: [Punch]
reverse.
Display Description
Punch HP Punch home position sensor (PUHPS)
Edge Face1 Punch paper edge sensor (PUPES)
Tank Punch tank set switch (PUTSSW)
Tank Full Punch tank full sensor (PUTFS)
Completion
1-3-119
2LK/2LN/2LM/2LC

U243 Checking the operation of the DP motors
Description
Turns the motors or solenoids in the DP on.
Purpose
To check the operation of the DP motors and solenoids.
Method
Display Description
Feed Motor DP original feed motor (DPOFM) is turned on
Conv Motor DP original conveying motor (DPOCM) is turned on
Rev Motor DP switchback motor (DPSBM) is turned on
Lift Motor DP lift motor (DPLM) is turned on
Rev Press Sol DP pressure solenoid (DPPSOL) is turned on
Rev Branch Sol DP feedshift solenoid (DPFSSOL) is turned on
4. To turn each motor off, press the stop key.
Completion
Press the stop key when operation stops. The screen for selecting a maintenance item No. is dis-
played.
1-3-120
2LK/2LN/2LM/2LC

U244 Checking the DP switches
Description
Displays the status of the respective switches and sensors in the DP.
Purpose
To check if respective switches and sensors in the DP operate correctly.
Method
reverse.
Display Description
Feed DP feed sensor (DPFS)
Regist DP registration sensor (DPRS)
Timing DP timing sensor (DPTS)
CIS Head DP CIS sensor (DPCS)
Tray DP switchback sensor (DPSBS)
Set DP original sensor (DPOS)
Longitudinal DP original length switch (DPOLSW)
Lift U-Limit DP lift sensor 1 (DPLS1)
Lift L-Limit DP lift sensor 2 (DPLS2)
Cover Open DP interlock switch (DPILSW)
Open DP open/close switch (DPOCSW)
Eject DP eject sensor (DPES)
Slant DP slant sensor (DPSS)
Completion
1-3-121
2LK/2LN/2LM/2LC

U245 Checking messages
Description
Displays a list of messages on the touch panel of the operation panel.
Purpose
To check the messages to be displayed.
Method
2. Change the message using the cursor up/down keys.
When a message number is entered with the numeric keys and then the start key is pressed,
the message corresponding the specified number is displayed.
3. Change the language using the +/- keys.
Completion
1-3-122
2LK/2LN/2LM/2LC

U246 Setting the finisher
Description
Provides various settings for the 1000-sheet finisher or 4000-sheet finisher, if furnished.
Purpose
Adjustment of registration stop timing in punch mode
Adjust if skewed paper conveying occurs or if the copy paper is Z-folded in punch mode.
Adjustment of paper stop timing in the punch mode
To adjust this item when the position of a punch hole is different from the specified one.
Adjustment of center position timing in the punch mode
Adjusts the center position of a punch hole in punch mode if the position is not proper.
Adjustment of front/rear side registration home position
Provides optimization when paper jam occurs due to an inferior fitting of the side registration
guides to paper.
Adjustment of front/rear shift home position
Performed when alighment is lost with the ejected paper
Adjusting of front/back stapling home position
Adjusts the stapling position in the staple mode if the position is not proper.
Adjustment of upper/lower side registration home position
Provides optimization when paper jam occurs due to an inferior fitting of the side registration
guides to paper.
Adjustment of booklet stapling position
Adjusts the booklet stapling position in the stitching mode if the position is not proper.
Adjustment of center folding position
Adjusts the center folding position in the stitching mode if the position is not proper.
Adjustment of tri- folding position
Adjusts the tri-folding position in the stitching mode if the position is not proper.
Method
Display Description
Finisher Adjustment of 1000-sheet finisher and 4000-sheet finisher
Booklet Adjustment of center-folding unit
Method: [Finisher]
Display Description
Punch Regist Adjustment of registration stop timing in punch mode
Punch Feed Adjustment of the paper stop timing in punch mode
Punch Width Adjustment of the center position timing in punch mode
Width Front HP Adjustment of front side registration home position
Width Tail HP Adjustment of rear side registration home position
Shift Front HP Adjustment of front shift home position
Shift Tail HP Adjustment of rear shift home position
Staple HP Adjustment of front and back stapling home position
1-3-123
2LK/2LN/2LM/2LC

U246 Setting: [Punch Regist]
1. Select [Punch Regist].
Description Setting Initial Change in
Adjustment of registration stop timing -20 to 20 0 0.25 mm
If skewed paper conveying occurs (sample 1), increase the setting value. If the copy paper is
Z-folded (sample 2), decrease the setting value.
Sample 1 Sample 2
Figure 1-3-18
Setting: [Punch Feed]

1. Select [Punch Feed].
Adjustment of the paper stop timing -10 to 10 0 0.52 mm
If the distance of the position of a punch hole is smaller than the specified value A, increase
the setting value. If the distance is larger than the value A, decrease the setting value.
A
Preset value A: 13 mm (metric)
9.5 mm (inch)
Figure 1-3-19
1-3-124
2LK/2LN/2LM/2LC

U246 Setting: [Punch Width]
1. Select [Punch Width].
Adjustment of the punch center position timing -4 to 4 0 0.52 mm
If the punch hole is too close to the front of the machine, increase the setting value. If the
punch hole is too close to the rear of the machine, decrease the setting value.
Center line
(within ± 0.5 mm)
Sample 1 Sample 2
Figure 1-3-20
Setting: [Width Front HP/Width Tail HP]

1. Select [Width Front HP] or [Width Tail HP].
Adjustment of front side registration home position -15 to 15 0 0.19 mm
Adjustment of rear side registration home position -15 to 15 0 0.19 mm
4. Press the stop key. The screen for selecting a maintenance item No. is displayed.
5. Enter maintenance mode U240 and select [Motor], then [Width Test(A3)].
The width guides of the middle tray will move to A3-size position.
6. Pull the middle tray, insert paper between the guides and check that paper is abut the guides.
7. Repeat the above adjustment until paper is properly in position.
Setting: [Shift Front HP/Shift Tail HP]

1. Select [Shift Front HP] or [Shift Tail HP].
Adjustment of front shift home position -15 to 15 0 0.19 mm
Adjustment of rear shift home position -15 to 15 0 0.19 mm
5. Enter maintenance mode U240 and select [Motor], then [Sort Test].
6. Repeat the above adjustment until eject paper is properly in position.
1-3-125
2LK/2LN/2LM/2LC

U246 Setting: [Staple HP]
1. Select [Staple HP].
Adjustment of front and back stapling home position -15 to 15 0 0.19 mm
When staple positions are off toward the front side of the machine (sample 1), increase the
setting value. When staple positions are off toward the rear side of the machine (sample 2),
decrease the setting value.
Sample 1 Sample 2
Figure 1-3-21
Method: [Booklet]
Display Description
Width Up HP Adjustment of upper side registration home position
Width Down HP Adjustment of lower side registration home position
Staple Pos1 Adjustment of booklet stapling position for A4/Letter size
Staple Pos2 Adjustment of booklet stapling position for B4/Legal size
Staple Pos3 Adjustment of booklet stapling position for A3/Ledger size
Booklet Pos1 Adjustment of center folding position for A4/Letter size
Booklet Pos2 Adjustment of center folding position for B4/Legal size
Booklet Pos3 Adjustment of center folding position for A3/Ledger size
Three Fold Adjustment of tri-folding position
1-3-126
2LK/2LN/2LM/2LC

U246 Setting: [Width Up HP/Width Down HP]
1. Select [Width Up HP] or [Width Down HP].
Adjustment of upper side registration home position -15 to 15 0 0.34 mm
Adjustment of lower side registration home position -15 to 15 0 0.34 mm
5. Enter maintenance mode U240 and select [Booklet], then [Width Test(A3)].
The width guides of the center-folding unit will move to A3-size position.
6. Pull the center-folding unit, insert paper between the guides and check that paper is abut the
guides.
7. Repeat the above adjustment until paper is properly in position.
Setting: [Staple Pos]

1. Select [Staple Pos1], [Staple Pos2] or [Staple Pos3].
Adjustment of booklet stapling position for -15 to 15 0 0.32 mm
A4/Letter size
B4/Legal size
A3/Ledger size
When staples are placed too far right (sample 1), decrease the preset value. When staples
are placed too far left (sample 2), increase the preset value.
Reference value: within ± 2 mm
2 mm 2 mm
Sample 1 Sample 2
Figure 1-3-22
1-3-127
2LK/2LN/2LM/2LC

U246 Setting: [Booklet Pos]
1. Select [Booklet Pos1], [Booklet Pos2] or [Booklet Pos3].
Adjustment of center folding position for A4/Letter size -15 to 15 0 0.32 mm
Adjustment of center folding position for B4/Legal size -15 to 15 0 0.32 mm
Adjustment of center folding position for A3/Ledger size -15 to 15 0 0.32 mm
When the centerfold position too far right (sample 1), increase the preset value. When the
centerfold position too far left (sample 2), decrease the setting value.
Reference value A: A4, Letter: Length of paper × 1/2 ± 2 mm
A3, Ledger, B4: Length of paper × 1/2 ± 3 mm
A
Center line Sample 1 Sample 2
Figure 1-3-23
Setting: [Three Fold]

1. Select [Three Fold].
Adjustment of tri-folding position -15 to 15 0 0.32 mm
When the tri-fold position too far right (sample 1), increase the preset value. When the tri-fold
position too far left (sample 2), decrease the setting value.
Reference value A: 7.0 ± 2 mm
A
Sample 1 Sample 2
Figure 1-3-24
Completion
1-3-128
2LK/2LN/2LM/2LC

U247 Setting the paper feed device
Description
Turns on motor and clutches of paper feeder device.
Purpose
To check the operation of motor and clutches of paper feed device.
Method
2. Select the paper feed device.
Display Description
2PF Paper feeder
LCF Large capacity feeder
Side Deck Side feeder
SMT SMT paper feeder
Side 2PF Side paper feeder
Side LCF Side large capacity feeder
Method: [2PF/Side 2PF]

1. Press [Motor], [Clutch] or [Solenoid] and select the item.
Display Description
Motor Off PF paper feed motor (PFPFM) is turned off
On PF paper feed motor (PFPFM) is turned on
Clutch C1 PF paper conveying clutch 1 (PFPCCL1) is turned on
C2 PF paper conveying clutch 2 (PFPCCL2) is turned on
V Feed(H) PF paper feed clutch 1 (PFPFCL1) is turned on
V Feed(L) PF paper feed clutch 2 (PFPFCL2) is turned on
Solenoid Cassette1 PF pickup solenoid 1 (PFPUSOL1) is turned on
Cassette2 PF pickup solenoid 2 (PFPUSOL2) is turned on
1-3-129
2LK/2LN/2LM/2LC

U247 Method: [LCF/Side LCF]
Display Description
Motor Off PF paper feed motor (PFPFM) is turned off
On PF paper feed motor (PFPFM) is turned on
Clutch C1 PF paper conveying clutch 1 (PFPCCL1) is turned on
C2 PF paper conveying clutch 2 (PFPCCL2) is turned on
V Feed PF paper conveying clutch 3 (PFPCCL3) is turned on
H Feed1 PF paper feed clutch 1 (PFPFCL1) is turned on
H Feed2 PF paper feed clutch 2 (PFPFCL2) is turned on
Solenoid Cassette1 PF pickup solenoid 1 (PFPUSOL1) is turned on
Cassette2 PF pickup solenoid 2 (PFPUSOL2) is turned on
Method: [Side Deck]

Display Description
Motor Off SF paper feed motor (SFPFM) is turned off
On SF paper feed motor (SFPFM) is turned on
Clutch C1 SF paper conveying clutch (SFPCCL) is turned on
Solenoid Cassette1 SF pickup solenoid (PFPUSOL) is turned on
Method: [SMT]
Display Description
Motor Off SMT paper feed motor (SMTPFM) is turned off
On SMT paper feed motor (SMTPFM) is turned on
Clutch C1 SMT paper conveying clutch 1 (SMTPCCL1) is turned on
C2 SMT paper conveying clutch 2 (SMTPCCL2) is turned on
H Feed SMT paper feed clutch (SMTPFCL) is turned on
Solenoid Cassette1 SMT pickup solenoid (SMTPUSOL) is turned on
Retard SMT feedshift solenoid (SMTFSSOL) is turned on
1-3-130
2LK/2LN/2LM/2LC

U247 Completion
U250 Checking/clearing the maintenance cycle
Description
Changes preset values for maintenance cycle and automatic grayscale adjustment.
Purpose
Provides changing the time when the message to acknowledge to conduct maintenance and
automatic grayscale adjustment is periodically displayed.
Setting
3. Change the setting using the +- keys or numeric keys.
M.Cnt A Preset values for maintenance cycle (kit A) 0 to 9999999
M.Cnt B Preset values for maintenance cycle (kit B) 0 to 9999999
M.Cnt C Preset values for maintenance cycle (kit C) 0 to 9999999
M.Cnt HT Preset values for automatic grayscale adjust- 0 to 9999999
ment
Clearing
1. Select [Clear].
2. Press the start key. The setting value is cleared.
Completion
1-3-131
2LK/2LN/2LM/2LC

U251 Checking/clearing the maintenance counter
Description
Displays and clears or changes the maintenance count and automatic grayscale adjustment
count.
Purpose
To verify the maintenance counter count and automatic grayscale count. Also to clear the count
during maintenance service.
Setting
2. Select the item to be changed.
M.Cnt A Count value for maintenance cycle (kit A) 0 to 9999999
M.Cnt B Count value for maintenance cycle (kit B) 0 to 9999999
M.Cnt C Count value for maintenance cycle (kit C) 0 to 9999999
M.Cnt HT Automatic grayscale adjustment count 0 to 9999999
Clearing
1. Select [Clear].
2. Press the start key. The setting value is cleared.
Completion
1-3-132
2LK/2LN/2LM/2LC

U252 Setting the destination
Description
Switches the operations and screens of the machine according to the destination.
Purpose
To be executed after initializing the backup RAM, in order to return the setting to the value before
replacement or initialization.
Method
2. Select the destination.
Display Description
Japan Metric Metric (Japan) specifications
Inch Inch (North America) specifications
Europe Metric Metric (Europe) specifications
Asia Pacific Metric (Asia Pacific) specifications
Australia Australia specifications
China China specifications
Korea Korea specifications
Error codes
Codes Description
0001 Entity error
0020 Engine error
0040 Scanner error
1-3-133
2LK/2LN/2LM/2LC

U253 Switching between double and single counts
Description
Switches the count system for the total counter and other counters for every color mode.
Purpose
Used to select, according to the preference of the user (copy service provider), if A3/Ledger
paper is to be counted as one sheet (single count) or two sheets (double count).
Setting
Display Description
Full Color Count system of full color mode
Mono Color* Count system of single color mode
B/W Count system of black/white mode
Displayed only if the setting of U276 (Setting the copy count mode) is Mode1.
3. Select the count system.
Display Description
SGL(All) Single count for all size paper
DBL(A3/Ledger) Double count for A3/Ledger size or larger
DBL(B4) Double count for B4 size or larger
DBL(Folio) Double count for Folio size or larger
Initial setting: DBL(A3/Ledger)
Completion
1-3-134
2LK/2LN/2LM/2LC

U260 Selecting the timing for copy counting
Description
Changes the copy count timing for the total counter and other counters.
Purpose
To be set according to user request.
Setting
2. Select the copy count timing.
Display Description
Feed When secondary paper feed starts
Eject When the paper is ejected
Initial setting: Eject
Completion
U265 Setting OEM purchaser code
Description
Sets the OEM purchaser code.
Purpose
Sets the code when replacing the main PWB and the like.
Setting
2. Change the setting value using the numeric keys.
1-3-135
2LK/2LN/2LM/2LC

U271 Setting the page count
Description
Banner counting
Purpose
To change when modifying counting Banner
Setting
2. Select the item.
Banner A Counting for Banner A (470.1mm to 915mm/
18.51” to 36”)
Banner B Counting for Banner B (915.1mm to 1,220mm/
36.01” to 48”)
Completion
U276 Setting the copy count mode
Description
Sets the count mode of single color mode.
Purpose
To change the charging counter which counts up in single color printing.
Setting
2. Select the mode.
Display Description
Mode0 This lets the full color counter count up in single color
Mode1 This lets the single color counter count up in single color
Initial setting: Mode 0
Completion
1-3-136
2LK/2LN/2LM/2LC

U278 Setting the delivery date
Description
Enter delivery date in month, day, and year.
Purpose
To operate when installing the machine. Perform this to confirm the delivery date.
Method
2. Select [Today].
3. Press the start key. The delivery date is set.
Clearing
1. Select [Clear].
2. Press the start key. The delivery date is cleared.
Completion
U284 Setting 2 color copy mode
Description
Sets whether to use 2 color copy mode.
Purpose
According to user request, changes the setting.
Setting
Display Description
On 2 color copy mode is enabled
Off 2 color copy mode is disabled
If On is selected, 2-color copy will be displayed on the color function screen.
Completion
1-3-137
2LK/2LN/2LM/2LC

U285 Setting service status page
Description
Determines displaying the print coverage report on reporting.
Purpose
Setting
Display Description
On Displays the print coverage
Off Not to display the print coverage
Initial setting: On
Completion
U323 Setting abnormal temperature and humidity warning
Description
Specify whether or not a notice is displayed on the operation panel when abnormal temperature
and humidity is detected.
Purpose
Setting
Display Description
On Displays the abnormal temperature and humidity warning
Off Not to display the abnormal temperature and humidity warning
Initial setting: On
Completion
1-3-138
2LK/2LN/2LM/2LC

U325 Setting the paper interval
Description
Determines the interval between pages and the toner replenishment amount when printing pages
with high print coverage.
Purpose
Modify the settings only if a spotted background or uneven density appears when printing pages
with high print coverage.
Method
Display Description
Interval Paper interval control ON/OFF setting
Mode Setting mode of the paper interval control
Setting: [Interval]
Display Description
On Paper interval control is performed
Off Paper interval control is not performed
Initial setting: On
Setting: [Mode]
Setting Initial
Display Description
range setting
Mode Paper interval control mode when printing high 1 to 10 1
density original continuously
If a spotted background appears when printing pages with high print coverage, change the
setting to 5. However, if you prefer to give priority to printing speed, change the setting to 4.
Completion
1-3-139
2LK/2LN/2LM/2LC

U326 Setting the black line cleaning indication
Description
Sets whether to display the cleaning guidance when detecting the black line.
Purpose
Displays the cleaning guidance in order to make the call for service with the black line decrease
by the rubbish on the contact glass when scanning from the DP.
Method
Display Description
Black Line Mode Black line cleaning guidance ON/OFF setting
Black Line Cnt Setting counts of the cleaning guidance indication
Setting: [Black Line Mode]

Display Description
On Displays the cleaning guidance
Off Not to display the cleaning guidance
Initial setting: On
Setting: [Black Line Cnt]

Setting Initial
Display Description
range setting
Cnt Setting counts of the cleaning guidance indi- 0 to 255 8
cation ( x 1000 sheets)
When setting is 0, the black line cleaning indication is displayed only if the black line is
detected.
Completion
1-3-140
2LK/2LN/2LM/2LC

U327 Setting the cassette heater control
Description
Sets the cassette heater control.
Purpose
To change the setting according to the machine installation environment.
Setting
Display Description
On Cassette heater ON
Off Cassette heater OFF
Completion
1-3-141
2LK/2LN/2LM/2LC

U332 Setting the size conversion factor
Description
Sets the coefficient of nonstandard sizes in relation to the A4/Letter size. The coefficient set here
is used to convert the black ratio in relation to the A4/Letter size and to display the result in user
simulation.
Purpose
To set the coefficient for converting the black ratio for nonstandard sizes in relation to the A4/Let-
ter size.
Method
Display Description
Mode Toggling full-color count and color coverage count display
Coverage(L) Size coefficient (Low coverage)
Coverage(M) Size coefficient (Middle coverage)
Setting: [Mode]
1. Select the mode.
Display Description
0 Full-color count display
1 Color coverage count display
Initial setting: 0
Setting: [Coverage(L)/(M)]
1. Select the item.
2. Change the setting using the +/-keys or numeric keys.
Setting Initial
Display Description
range setting
Coverage(L) Size coefficient (Low coverage) 0.1 to 100 1.0
Coverage(M) Size coefficient (Middle coverage) 0.1 to 100 1.0
Completion
1-3-142
2LK/2LN/2LM/2LC

U340 Setting the applied mode
Description
Allocates memory to ensure that there is sufficient memory available for the printer to use as a
working area.
Purpose
Modify the memory allocation if insufficient memory for transparency support or XPS direct print-
ing occurs.
Setting
Setting Initial
Display Description
range setting
Image Area temporarily used to create output 0 to 400 (MB) 0
image.
Image(Detail) Area temporarily used to hold down- 0 to 400 (MB) 0
loaded font and other data.
Set the values below in case print failure occurs with the memory shortage.
(recommended value)
Image : +190
Image(Detaile) : +1
Supplement
The work area for copy is small and it may cause output failure if the values are large.
1-3-143
2LK/2LN/2LM/2LC

U341 Specific paper feed location setting for printing function
Description
Sets a paper feed location specified for printer output (only if a printer kit is installed).
Purpose
To use a paper feed location only for printer output.
A paper feed location specified for printer output cannot be used for copy output.
Method
2. Select the paper feed location for the printer.
Two or more cassette can be selected.
Display Description
Cassette1 Cassette 1
Cassette3 Cassette 3 (paper feeder/large capacity feeder)
Cassette5 Cassette 5 (SMT paper feeder/side feeder)
Cassette6 Cassette 6 (side paper feeder/side large capacity feeder)
When an optional paper feed device is not installed, the corresponding count is not dis-
played.
Completion
1-3-144
2LK/2LN/2LM/2LC

U343 Switching between duplex/simplex copy mode
Description
Switches the initial setting between duplex and simplex copy.
Purpose
To be set according to frequency of use: set to the more frequently used mode.
Setting
Display Description
On Duplex copy
Off Simplex copy
Completion
U345 Setting the value for maintenance due indication
Description
Sets when to display a message notifying that the time for maintenance is about to be reached,
by setting the number of copies that can be made before the current maintenance cycle ends.
When the difference between the number of copies of the maintenance cycle and that of the
maintenance count reaches the set value, the message is displayed.
Purpose
To change the time for maintenance due indication.
Setting
Setting Initial
Display Description
range setting
Cnt Time for maintenance due indication 0 to 9999 0
(Remaining number of copies that can be made
before the current maintenance cycle ends)
Completion
1-3-145
2LK/2LN/2LM/2LC

U402 Adjusting margins of image printing
Description
Adjusts margins for image printing.
Purpose
Make the adjustment if margins are incorrect.
Adjustment
Display Description
Lead Printer leading edge margin 0.0 to 10.0 4.0 0.1 mm
A Margin Printer left margin 0.0 to 10.0 3.0 0.1 mm
C Margin Printer right margin 0.0 to 10.0 3.0 0.1 mm
Trail Printer trailing edge margin 0.0 to 10.0 3.9 0.1 mm
Increasing the value makes the margin wider, and decreasing it makes the margin narrower.
Printer leading edge margin

(4.5 ± 0.5 mm)
Printer Printer
left margin right margin
(2.0 +1.0/-0.5 mm) (2.0 +1.0/-0.5 mm)
Printer trailing edge margin

(2.0 +1.0/-0.5 mm)
Figure 1-3-25
Caution
U403 U404
U402
(P.1-3-147) (P.1-3-148)
Completion
1-3-146
2LK/2LN/2LM/2LC

U403 Adjusting margins for scanning an original on the contact glass
Description
Adjusts margins for scanning the original on the contact glass.
Purpose
Adjustment
Display Description
A Margin Scanner left margin 0.0 to 10.0 2.0 0.5 mm
B Margin Scanner leading edge margin 0.0 to 10.0 2.0 0.5 mm
C Margin Scanner right margin 0.0 to 10.0 2.0 0.5 mm
D Margin Scanner trailing edge margin 0.0 to 10.0 2.0 0.5 mm
Scanner leading edge margin

(3.0 ± 2.5 mm)
Scanner Scanner
left margin right margin
(2.5 +1.5/-2.0 mm) (2.5 +1.5/-2.0 mm)
Scanner trailing edge margin

(3.0 ± 2.0 mm)
Figure 1-3-26
Caution
U404
U403
(P.1-3-148)
Completion
1-3-147
2LK/2LN/2LM/2LC

U404 Adjusting margins for scanning an original from the DP
Description
Adjusts margins for scanning the original from the DP.
Purpose
Caution
Before making this adjustment, ensure that the following adjustments have been made in mainte-
nance mode
U402 U403
U404
(P.1-3-146) (P.1-3-147)
Adjustment
Display Description
A Margin DP left margin 0.0 to 10.0 2.0 0.5 mm
B Margin DP leading edge margin 0.0 to 10.0 2.0 0.5 mm
C Margin DP right margin 0.0 to 10.0 2.0 0.5 mm
D Margin DP trailing edge margin 0.0 to 10.0 2.0 0.5 mm
A Margin DP left margin (second side) 0.0 to 10.0 2.0 0.5 mm
(Back)
B Margin DP leading edge margin 0.0 to 10.0 2.0 0.5 mm
(Back) (second side)
C Margin DP right margin (second side) 0.0 to 10.0 2.0 0.5 mm
(Back)
D Margin DP trailing edge margin 0.0 to 10.0 2.0 0.5 mm
(Back) (second side)
* : Dual scan DP only
1-3-148
2LK/2LN/2LM/2LC

U404 6. Change the setting value using the cursor left/right keys or numeric keys.
DP leading edge margin

(3.0 ± 1.5 mm)
DP DP right margin
left margin (2.0 ± 1.0 mm)
(2.0 ± 1.0 mm)
DP trailing edge margin

(2.0 ± 1.0 mm)
Figure 1-3-27
Completion
1-3-149
2LK/2LN/2LM/2LC

U407 Adjusting the leading edge registration for memory image printing
Description
Adjusts the leading edge registration during memory copying.
Purpose
Make the following adjustment if there is a regular error between the leading edge of the copy
image on the front face and that on the reverse face during duplex switchback copying.
Caution
Before making this adjustment, ensure that the following adjustments have been made in mainte-
nance mode
U034 U402 U066 U403 U071

(P.1-3-33) (P.1-3-146) (P.1-3-53) (P.1-3-147) (P.1-3-58)
U404
U407
(P.1-3-148)
Adjustment
Display Description
Adj Data Leading edge registration for -47 to 47 0 0.1 mm
memory image printing
For copy example 1, decrease the value. For copy example 2, increase the value.
Original Copy Copy

example 1 example 2
Figure 1-3-28
Completion
1-3-150
2LK/2LN/2LM/2LC

U410 Adjusting the halftone automatically
Description
Carries out processing for the data acquisition that is required in order to perform either auto-
matic adjustment of the halftone or the ID correction operation. Also the color table is changed
when an offset occurs.
Purpose
Performed when the quality of reproduced halftones has dropped. Also when an offset occurs,
the setting of color table is changed to table2.
Method
2. Select the item.
Display Description
Normal Mode Executing the automatic adjustment of the halftone
(continuous adjustment)
Single Mode Executing the automatic adjustment of the halftone
(individual adjustment)
Setting Table Switching the color table
Method: [Normal Mode]

1. Select [Normal Mode].
2. Press the start key. A test patterns 1, 2 and 3 are outputted.
3. Place the output test pattern 1 as the original.
Adjustment is made (first time).
Adjustment is made (second time).
Adjustment is made (third time).
9. When normally completed, [Finish] is displayed.
If a problem occurs during auto adjustment, error code is displayed.
1-3-151
2LK/2LN/2LM/2LC

U410 Error codes
Codes Description Codes Description
S001 Patch not detected E001 Engine status error
S002 Original deviation in the main E002 Engine sensor error
scanning direction
EFFF Engine other error
S003 Original deviation in the auxil- C001 Controller error
iary scanning direction
C100 Adjustment value error
S004 Original inclination error C200 Adjustment value error
S005 Original type error CFFF Controller other error
SFFF Scanner other error
Method: [Single Mode]

1. Select the item.
Display Description
AM Individual screen adjustment
FM Adjustment depending on error diffusions
B/W Adjustment depending on Black and white
2. Press the start key. A test pattern is outputted.

3. Place the output test pattern as the original.
Place approximately 20 sheets of white paper on the test pattern and set them.
Adjustment is made.
Method: [Setting Table]

1. Select the item.
Display Description
Table1 Normal color table
Table2 Color tables for improving reproduction of characters at black
and white printing
Table3 More fidelity than Table2
Initial setting: Table1
Completion
1-3-152
2LK/2LN/2LM/2LC

U411 Adjusting the scanner automatically
Description
Uses a specified original and automatically adjusts the following items in the scanner and the DP
scanning sections.
Purpose
To perform automatic adjustment of various items in the scanner and the DP scanning sections.
Perform adjustments using a new test charrt (chart 1) when replacing ISC PWB and/or LED
PWB.
Method
2. Select the item.
Original to be used
Display Description
for adjustment (P/N)
Table (Chart1) Automatic adjustment in the scanner sec- 7505000005
tion (chart 1)
DP FaceUp Automatic adjustment in the DP scanning 7505000005
(Chart1) section (first side) (chart 1)
DP FaceDown Automatic adjustment in the DP scanning 7505000005
(Chart1) section (second side) (chart 1)
Table (Chart2) Automatic adjustment in the scanner sec- 302FZ56990
tion (chart 2)
DP FaceUp Automatic adjustment in the DP scanning 302AC68243
(Chart2) section (first side) (chart 2)
DP FaceDown Automatic adjustment in the DP scanning 302AC68243/
(Chart2) section (second side) (chart 2) 303JX57010/
303JX57020
Target Set-up for obtaining the target value -
DP Auto Adj Automatic adjustment of automatic docu- -
ment processor using the chart printed
from the machine
Method: [Table (Chart1)]

To manually enter the target value
1. Enter the target values which are shown on the specified original (P/N: 7505000005) execut-
ing maintenance item U425. Set a specified original (P/N: 7505000005) on the platen.
2. Enter maintenance item U411.
3. Select [Target].
4. Select [U425] and press the start key.
5. Select [Table (Chart1)].
6. Select the item.
1-3-153
2LK/2LN/2LM/2LC

U411 To manually enter the target value
1. Set a specified original (P/N: 7505000005) on the platen.
3. Select [Target].
4. Select [Auto] and press the start key.
6. Select the item.
Display Description
All Executing the all scanner adjustment
LED/AGC Executing the adjustment for LED light quantity/AGC
White Executing the white reference compensation coefficient
Input Executing the adjustment for magnification, leading edge tim-
ing and center line
C.A. Executing the adjustment for chromatic aberration filter
MTF Executing the adjustment for MTF filter
Gamma Executing the adjustment for input gamma
Matrix Executing the adjustment for matrix
7. Press the start key. Auto adjustment starts.
* : When automatic adjustment has normally completed, [OK] is displayed. If a problem
occurs during auto adjustment, error code is displayed and operation stops. Should this
happen, determine the details of the problem and repeat the procedure from the begin-
ning.
Method: [DP FaceUp (Chart1)]

ing maintenance item U425. Set a specified original (P/N: 7505000005) on the DP face up.
3. Select [Target].
5. Select [DP FaceUp (Chart1)].
6. Select [Input].

1. Set a specified original (P/N: 7505000005) on the DP face up.
3. Select [Target].
6. Select [Input].
Display Description
Input Executing the adjustment in the DP scanning section (first
side) for magnification, leading edge timing and center line
1-3-154
2LK/2LN/2LM/2LC

U411 7. Press the start key. Auto adjustment starts.
ning.
Method: [DP FaceDown (Chart1)]

ing maintenance item U425. Set a specified original (P/N: 7505000005) on the DP face
down.
3. Select [Target].
5. Select [DP FaceDown (Chart1)].
6. Select [All].

1. Set a specified original (P/N: 7505000005) on the DP face down.
3. Select [Target].
5. Select [DP FaceDown (Chart1)].
6. Select [All].
Display Description
All Executing the adjustment in the DP scanning section (second
side) for magnification, leading edge timing, center line, MTF
filter, input gamma and matrix
ning.
1-3-155
2LK/2LN/2LM/2LC

U411 Method: [Table (Chart2)]
1. Enter the target values which are shown on the specified original (P/N: 302FZ56990) execut-
ing maintenance item U425.
2. Set a specified original (P/N: 302FZ56990) on the platen.
4. Select [Target].
7. Select the item.
Display Description
All Executing the all scanner adjustment
Input Executing the adjustment for magnification, leading edge tim-
ing and center line
C.A. Executing the adjustment for chromatic aberration filter
MTF Executing the adjustment for MTF filter
Gamma Executing the adjustment for input gamma
Matrix Executing the adjustment for matrix
ning.
Method: [DP FaceUp (Chart2)]

1. Measure the leading edge, main scanning, and auxiliary scanning of the specified original (P/
N: 302AC68243) and enter the values by executing maintenance item U425.
2. Set a specified original (P/N: 302AC68243) on the DP.
Cut the trailing edge of the original.
5 mm
149 ± 1 mm
74 ± 1 mm
Figure 1-3-29
4. Select [Target].
7. Select [INPUT].
Display Description
Input Executing the adjustment in the DP scanning section (first
side) for magnification, leading edge timing and center line
1-3-156
2LK/2LN/2LM/2LC

U411 8. Press the start key. Auto adjustment starts.
ning.
Method: [DP FaceDown (Chart2)]

1. Place the specified original for acquiring gamma target data (P/N: 303JX57010) on the
platen, and press the start key.
2. Place the specified original for acquiring matrix target data (P/N: 303JX57020) on the platen,
and press the start key.
When normally completed, [OK] is displayed.
3. Select the item.
Original to be used
Display Description
for adjustment (P/N)
All Executing the adjustment in the DP scan- 302AC68243/
ning section (second side) for magnifica- 303JX57010/
tion, leading edge timing, center line, MTF 303JX57020
filter, input gamma and matrix
Input Executing the adjustment in the DP scan- 302AC68243
ning section (second side) for magnifica-
tion, leading edge timing and center line
MTF/Gamma Executing the adjustment in the DP scan- 303JX57010
ning section (second side) for MTF filter
and input gamma
Matrix Executing the adjustment in the DP scan- 303JX57020
ning section (second side) for matrix
[Input]
1. Select [Input].
2. Set a specified original (P/N: 302AC6824) on the DP face down.
[MTF/Gamma]
1. Select [MTF/Gamma].
2. Set a specified original (P/N: 303JX57010) on the DP face down.
[Matrix]
1. Select [Matrix].
2. Set a specified original (P/N: 303JX57020) on the DP face down.
When [ALL] is selected, the adjustment of [Input], [MTF/Gamma] and [Matrix] can be executed at
once. When adjusting, place the three specified originals on the DP face down, and then press
the start key.
Set the original 303JX57020, and then place 303JX57010 and 302AC68243 in order on the top
of the original.
1-3-157
2LK/2LN/2LM/2LC

U411 * : When automatic adjustment has normally completed, [OK] is displayed. If a problem
ning.
Method: [DP Auto Adj]

1. Press the start key to output the original for adjustment.
2. Set the output the original for adjustment and press the start key.
3. Set the output the original for adjustment on the DP face up.
4. Press the start key. Auto adjustment of first side starts.
5. Set the output the original for adjustment on the DP face down.
6. Press the start key. Auto adjustment of second side starts.
ning.
Error Codes
Codes Description
S001 Black band is not detected (main scanning direction far end)
S002 Black band is not detected (main scanning direction near end)
S003 Black band is not detected (auxiliary scanning direction leading edge)
S004 Black band is not detected (auxiliary scanning direction trailing edge)
S005 Auxiliary scanning direction skew 1.5 error
S006 Main scanning direction skew 1.5 error
S007 Original error (detection of reverse original paper)
S008 Original error (page mismatch)
C001 Controller error
CFFF Controller other error
Completion
1-3-158
2LK/2LN/2LM/2LC

U412 Adjusting the uneven density
Description
Adjusts the uneven developer/transfer density in the drum axis direction by scanning directly the
density distribution of test pattern with the scanner and adjusting LSU light quantity.
Purpose
To perform when replacing the drum unit or laser scanner unit.
Method
2. Select the item.
Display Description
Normal Mode Executing the uneven density correction
On/Off Config Uneven density correction ON/OFF setting
Method: [Normal Mode]

1. Select [Default Value].
A test pattern is outputted with the initial light quantity setting. (1st sheet)
2. Place approximately 20 sheets of white paper on the output test pattern and place as the
original.
3. Press the start key. the correction starts.
4. After the correction is completed, and press the start key.
A test pattern is outputted. (2nd sheet)
A test pattern is outputted with light quantity setting lower than the 1st test pattern by 20%.
original.
6. Press the start key. the correction starts.
7. After the correction is completed, and press the start key.
A test pattern is outputted. (3rd sheet)
original.
The correction result is checked. When normally completed, [OK] is displayed.
Retry (1st time)

10. If the correction is not completed normally, [Retry] is displayed.
11. Repeat steps 4 and 9.
Retry (2nd time)

12. If the correction is not completed normally, [Retry] is displayed.
13. Repeat steps 4 and 9.
If a problem occurs during auto correction, error code is displayed.
1-3-159
2LK/2LN/2LM/2LC

U412 Error codes
S001 Patch not detected E001 Engine status error
S002 Original deviation in the main E002 Spotted background error
scanning direction
E003 Density error
S003 Original deviation in the auxil- E004 Uneven density error
EFFF Engine other error
S004 Original inclination error C001 Controller error
S005 Original type error CFFF Controller other error
Setting: [On/Off Config]

Display Description
On Uneven density correction is enabled
Off Uneven density correction is disabled
ON is automatically set after the correction is complete.
Completion
1-3-160
2LK/2LN/2LM/2LC

U415 Adjusting the print position automatically
Description
Automatically adjusts timings at the print engine.
Adjustment for leading edge timing, center line, magnification and margin.
Purpose
Used to make respective auto adjustments for the print engine.
Method
3. Press the start key. A test pattern is outputted
4. Set the output test pattern as the original.
Error Codes
Codes Description
S001 Black band is not detected (main scanning direction far end)
S002 Black band is not detected (main scanning direction near end)
S003 Black band is not detected (auxiliary scanning direction leading edge)
S004 Black band is not detected (auxiliary scanning direction trailing edge)
S005 Auxiliary scanning direction skew 1.5 error
S006 Main scanning direction skew 1.5 error
S007 Original error (detection of reverse original paper)
S008 Original error (page mismatch)
C101 Adjustment value error (main scanning direction magnification)
C102 Adjustment value error (auxiliary scanning direction magnification)
C103 Adjustment value error (leading edge timing)
C104 Adjustment value error (center line)
C105 Adjustment value error (B margin)
C106 Adjustment value error (A margin)
C107 Adjustment value error (C margin)
C108 Adjustment value error (D margin)
CFFF Controller other error
Completion
1-3-161
2LK/2LN/2LM/2LC

U425 Setting the target
Description
Enters the lab values that is indicated on the back of the chart 1 (P/N: 7505000005) or chart 2
(P/N: 302FZ56990) used for adjustment.
Purpose
Performs data input in order to correct for differences in originals during automatic adjustment.
Method
Select the chart to be used.
Display Description
Chart1 Chart 1 (P/N: 7505000005)
Chart2 Chart 2 (P/N: 302FZ56990)
Method: [Chart1]
Display Description
White Setting the white patch for the original for adjustment
Black Setting the black patch for the original for adjustment
Gray1 Setting the Gray1 patch for the original for adjustment
C Setting the cyan patch for the original for adjustment
M Setting the magenta patch for the original for adjustment
Y Setting the yellow patch for the original for adjustment
R Setting the red patch for the original for adjustment
G Setting the green patch for the original for adjustment
B Setting the blue patch for the original for adjustment
Adjust Original Setting the main and auxiliary scanning directions
L Setting the L value 0.0 to 100.0
a Setting the a value -200.0 to 200.0
b Setting the b value -200.0 to 200.0
4. Enters the value that is indicated on the back of the chart using the +/- keys or numeric keys.
1-3-162
2LK/2LN/2LM/2LC

U425 Setting: [Adjust Original]
1. Measure the distance from the leading edge to the top of black belt 1 of the original at A, B
and C.
Measurement procedure
1) Measure the distance from the leading edge to the top of black belt 1 of the original at A
(30 mm from the left edge), B (148.5 mm from the left edge) and C (267 mm from the left
edge), respectively.
2) Apply the following formula for the values obtained: ((A + B + C) / 3)
2. Enter the values solved using the cursor left/right keys or numeric keys in [Dist1].
4. Measure the distance from the left edge to the right edge black belt 2 of the original at F.
1) Measure the distance from the left edge to the right edge black belt 2 of the original at F
(15 mm from the top edge of black belt 1).
5. Enter the values using the cursor left/right keys or numeric keys in [Dist2].
7. Measure the distance from the top edge of black belt 1 to the bottom of black belt 3 of the
original at D and E.
1) Measure the distance from the top edge of black belt 1 to the bottom of black belt 3 of the
original at D (30 mm from the left edge) and E (267 mm from the left edge), respectively.
2) Apply the following formula for the values obtained: (D/2 + E/2)
8. Enter the measured value using the cursor left/right keys or numeric keys in [Dist3].
30mm 148.5mm 267mm
A Black belt 1 B C Leading edge

15mm
Black
belt 2
D E
Left edge
[Dist1] = (A+B+C)/3
[Dist2] = F
[Dist3] = D/2+E/2
COLOR SCANNER
CHART A4
No.302K357010
Black belt 3
Original for adjustment (P/N: 7505000005)
Figure 1-3-30
1-3-163
2LK/2LN/2LM/2LC

U425 Method: [Chart2]
2. Select the item.
Display Description
CCD Entering the target values of the chart (P/N: 302FZ56990)
used for adjustment
DP Entering the measurement value of the chart (P/N:
302AC68243) used for adjustment
CIS Execution is not required
Method: [CCD]
Display Description
N850 Setting the N850 patch for the original for adjustment
C Setting the cyan patch for the original for adjustment
M Setting the magenta patch for the original for adjustment
Y Setting the yellow patch for the original for adjustment
R Setting the red patch for the original for adjustment
G Setting the green patch for the original for adjustment
B Setting the blue patch for the original for adjustment
Adjust Original Setting the main and auxiliary scanning directions
L Setting the L value 0.0 to 100.0
a Setting the a value -200.0 to 200.0
b Setting the b value -200.0 to 200.0
3. Enters the value that is indicated on the back of the chart using the +/- keys or numeric keys.
1-3-164
2LK/2LN/2LM/2LC

U425 Setting: [Adjust Original]
1. Measure the distance from the left edge to the black belt (a) of the original at A, B and C.
1) Measure the distance from the edge to the black belt (a) of the original at A (30 mm from
the leading edge), B (148.5 mm from the leading edge) and C (267 mm from the leading
edge), respectively.
2) Apply the following formula for the values obtained: ((A + C) / 2 + B) / 2
2. Enter the values solved using the cursor left/right keys or numeric keys in [Vertical].
4. Measure the distance from the leading edge to the black belt (b) of the original at D, E and F.
1) Measure the distance from the edge to the black belt (b) of the original at D (35 mm from
the left edge), E (110 mm from the left edge) and F (185 mm from the left edge), respec-
tively.
2) Apply the following formula for the values obtained: ((D + F) / 2 + E) / 2
5. Enter the values solved using the cursor left/right keys or numeric keys in [Horezon].
7. Measure the length (G) from the edge of the black belt (b) to edge of the black belt (c) of the
original.
8. Enter the measured value using the cursor left/right keys or numeric keys in [Lead].
Leading edge
30 mm 148.5 mm 267 mm
Left edge
A B C
Black
35 mm belt (a)
D
Black Black
belt (b) belt (c)
110 mm [Vertical] =
E
((A + C) / 2 + B) / 2
G
[Horizon] =
((D + F) / 2 + E) / 2
[Lead] = G
185 mm
F
Original for adjustment (P/N: 302FZ56990)
Figure 1-3-31
1-3-165
2LK/2LN/2LM/2LC

U425 Setting: [DP]
1. Measure the distance from the leading edge to the black belt (inside) of the original at A.
2. Enter the measured value using the +/- keys in [Vertical].
3. Measure the distance from the left edge to the black belt (inside) of the original at B.
4. Enter the measured value using the +/- keys in [Horizon].
5. Measure the distance from the black belt of leading edge (inside) to the black belt of trailing
edge (inside) of the original at C.
6. Enter the measured value using the +/- keys in [Lead].
Original for adjustment (P/N: 302AC68243)
Figure 1-3-32
Completion
1-3-166
2LK/2LN/2LM/2LC

U429 Setting the offset for the color balance
Description
Displays and changes the density for each color during copying in the various image quality
modes.
Purpose
To change the balance for each color.
Method
2. Select the image quality mode.
Display Description
Text+Photo Density of each color in the text & photo mode
Photo Density of each color in the photo mode
Photo/Printout Density of each color in the printed photo mode
Text Density of each color in the text mode
Graphics/Map Density of each color in the map mode
Copy/Printout Density of each color in the printed document mode
Setting
Initial
setting
C Value of the cyan setting -5 to 5 (0 to 10*) 0
M Value of the magenta setting -5 to 5 (0 to 10*) 0
Y Value of the yellow setting -5 to 5 (0 to 10*) 0
K Value of the black setting -5 to 5 (0 to 10*) 0
*: When selecting [Copy/Printout]
Increasing the value darkens the density and decreasing it lightens the density.
Supplement
Completion
1-3-167
2LK/2LN/2LM/2LC

U464 Setting the ID correction operation
Description
Turns ID correction (calibration) on or off. Also, this allows individual settings for calibration oper-
ation.
Purpose
To restrict calibration when poor image quality is generated. Also, this allows individual settings
for calibration depending on the user preferences.
To perform the calibration when replacing the maintenance kit.
Method
Display Description
Permission Setting to turn calibration on/off
Time Interval Setting the interval time of calibration after printing
Mode Setting the color print execution mode
On/Sleep Out Setting execution parameters for calibration when powered up
or reverted from auto-sleep
AP/NE Paper interval calibration ON/OFF setting at the time of cali-
bration/near end after toner feed
Leaving Time Setting the standard time for judging whether or not to carry
out calibration based on the sleep time when the machine
recovers from the sleep mode
Driving Time Setting the standard time for judging whether or not to carry
out paper interval calibration based on the driving time during
printing
Timing Setting the standard time for judging whether or not to carry
out calibration based on the continuous print driving time dur-
ing printing
Target Value Setting the sensor target values for toner thick layer calibration
and light amount calibration
Print Rate(B/W) Setting the proportion of black/white printing at which black/
white calibration is executed during color printing.
Calib Executing the calibration
Setting: [Permission]
Display Description
On Turns calibration ON
Off Turns calibration OFF
Initial setting: On
1-3-168
2LK/2LN/2LM/2LC

U464 Setting: [Time Interval]
Setting Initial
Display Description
range setting
Time(sec) Setting the interval time of calibration 0 to 9999 (s) 480
Setting: [Mode]
1. Select the item.
Display Description
Short Setting the color print execution mode: short
Normal Setting the color print execution mode: normal
Long Setting the color print execution mode: long
Custom Setting the color print execution mode: custom
Auto Setting the color print execution mode: auto
Initial setting:
Setting: [On/Sleep Out]

Display Description
On Executes calibration if fuser temperature is less than 50°C/
122°F at power-up or recovery from auto sleep mode
Off Executes calibration regardless of fuser temperature at power-
up or recovery from auto sleep mode
Initial setting: On
Setting: [AP/NE]
Display Description
On Paper interval calibration at the time of calibration/near end
after toner feed is carried out
Off Paper interval calibration at the time of calibration/near end
after toner feed is not carried out
Initial setting: On
1-3-169
2LK/2LN/2LM/2LC

U464 Setting: [Leaving Time]
Initial
setting
Time(min) Setting the standard time of sleep mode 0 to 480 (min) 60
Setting: [Driving Time]

Initial
setting
Time(sec) Setting the drive standard time 300 to 3000 (s) 600
Setting: [Timing]
Initial
setting
Time(sec) Setting the drive standard time of con- 300 to 3600 (s) 1800
tinuous print
Setting: [Target Value]

1. Select the item.
Setting Initial
Display Description
range setting
Thickness(C) Toner thick layer calibration (cyan) 0 to 1000 500
Thickness(M) Toner thick layer calibration (magenta) 0 to 1000 500
Thickness(Y) Toner thick layer calibration (yellow) 0 to 1000 500
Thickness(K) Bias for addition in toner thick layer -100 to +100 10
calibration (black)
Gamma(C) Light amount calibration (cyan) 0 to 500 300
Gamma(M) Light amount calibration (magenta) 0 to 500 300
Gamma(Y) Light amount calibration (yellow) 0 to 500 300
Gamma(K) Light amount calibration (black) 0 to 500 300
1-3-170
2LK/2LN/2LM/2LC

U464 Setting: [Print Rate(B/W)]
Setting Initial
Display Description
range setting
Threshold Proportion of black/white printing 0 to 100 (%) 50
Method: [Calib]
2. Press the start key. Calibration is executed.
Completion
U465 Data reference for ID correction
Description
References the data related to ID correction.
Purpose
To check the corresponding data.
Method
2. Select the item to be reference.
Display Description
TCONT Developer bias control value after ID correction
Laser Power Scaling factor to the value determined in light amount calibration
Bias Calib Sensor value for toner thick layer calibration
T7 CTD T7 control value
Displaying: [TCOUNT]
1. Select [TCOUNT]. The current value is displayed.
Display Description
Before(C) Developer bias control value for cyan before ID correction
Before(M) Developer bias control value for magenta before ID correction
Before(Y) Developer bias control value for yellow before ID correction
Before(Y) Developer bias control value for black before ID correction
After(C) Developer bias control value for cyan after ID correction
After(M) Developer bias control value for magenta after ID correction
After(Y) Developer bias control value for yellow after ID correction
After(K) Developer bias control value for black after ID correction
1-3-171
2LK/2LN/2LM/2LC

U465 Displaying: [Laser Power]
1. Select [Laser Power]. The current value is displayed.
Display Description
C Scaling factor to the value determined in light amount calibration (cyan)
M Scaling factor to the value determined in light amount calibration (magenta)
Y Scaling factor to the value determined in light amount calibration (yellow)
K Scaling factor to the value determined in light amount calibration (black)
Displaying: [Bias Calib]

1. Select [Bias Calib]. The current value is displayed.
Display Description
C Sensor value for toner thick layer calibration (cyan)
M Sensor value for toner thick layer calibration (magenta)
Y Sensor value for toner thick layer calibration (yellow)
K Sensor value for toner thick layer calibration (black)
Displaying: [T7 CTD]

1. Select [T7 CTD]. The current value is displayed.
Display Description
C T7 control value (cyan)
M T7 control value (magenta)
Y T7 control value (yellow)
K T7 control value (black)
Completion
1-3-172
2LK/2LN/2LM/2LC

U467 Setting the color registration adjustment
Description
Sets the color registration adjustment and transfer belt speed correction. Also, determines the
conditions by which color registration correction is executed depending on the LSU temperature.
Purpose
If color variance is uneven due to a sensor failure, etc., turn this off and temporarily make a man-
ual adjustment.
Method
Display Description
Color Regist Setting the color registration correction operation
Belt Speed Setting the transfer belt speed correction operation
Timing After the previous correction is executed, color registration is
compensated as the LSU temperature varies by the value
determined.
Setting: [Color Regist]

Display Description
On Enables the color registration correction operation.
Off Disables the color registration correction operation.
Initial setting: On
Setting: [Belt Speed]

Display Description
On Enables the transfer belt speed correction operation.
Off Disables the transfer belt speed correction operation.
Initial setting: On
Setting: [Timing]
Setting Initial
Display Description
range setting
Timing Conditions for execution depending on 2 to 10 10
the LSU temperature variation
Completion
1-3-173
2LK/2LN/2LM/2LC

U468 Checking the color registration data
Description
Displays the color registration correction data and transfer belt speed correction data.
Purpose
To check the corresponding data.
Method
2. Select the item to be reference.
Display Description
V Correction Display the transfer speed adjustment value
Auto(C) Display the auto color registration adjustment value for cyan
Auto(M) Display the auto color registration adjustment value for magenta
Auto(Y) Display the auto color registration adjustment value for yellow
Manual(C) Display the manual color registration adjustment value for cyan
Manual(M) Display the manual color registration adjustment value for magenta
Manual(Y) Display the manual color registration adjustment value for yellow
Displaying: [V Correction]
1. Select [V Correction]. The current value is displayed.
Display Description
Speed transfer speed
Status transfer speed adjustment value
Displaying: [Auto(C)/Auto(M)/Auto(Y)]
1. Select [Auto(C)], [Auto(M)] or [Auto(Y)]. The current value is displayed.
Display Description
Horizon Auto color registration adjustment value of the main scanning
direction
Vertical Auto color registration adjustment value of the auxiliary scan-
ning direction
Magnification Auto color registration adjustment value of the magnification
Displaying: [Manual(C)/Manual(M)/Manual(Y)]
1. Select [Manual(C)], [Manual((M)] or [Manual((Y)]. The current value is displayed.
Display Description
Horizon Manual color registration adjustment value of the main scan-
ning direction
Vertical Manual color registration adjustment value of the auxiliary
scanning direction
Magnification Manual color registration adjustment value of the magnification
1-3-174
2LK/2LN/2LM/2LC

U468 Completion
U469 Adjusting the color registration
Description
Performs the color registration correction and transfer belt speed correction.
Purpose
To perform when replacing the maintenance kit or laser scanner unit.
Method
2. Select the item.
Display Description
Auto Executing the auto color registration correction
Manual Executing the manual color registration correction
Belt Initialize Executing the transfer belt speed correction
Method: [Auto]
1. Select [Print].
2. Press the start key. A chart for adjustment is outputted.
3. Set the output chart for adjustment as the original.
5. Press the start key. Color registration correction starts.
Chart for adjustment
Figure 1-3-33
1-3-175
2LK/2LN/2LM/2LC

U469 Error codes
S001 Patch not detected S004 Original inclination error
S002 Original deviation in the main S005 Original type error
scanning direction
S003 Original deviation in the auxil- CFFF Controller other error
Method: [Manual]
1. Select [Print].
2. Press the start key. A chart for adjustment is outputted.
3. Select [Regist].
4. Read figures at MH-1 to 7/CH-1 to 7/YH-1 to 7 and MV-3/CV-3/YV-3 of the reference chart
and enter the figure marked at the scale which the BK fine line is in line with the M/C/Y fine
lines, using the # key or * key.
(example)
When a red bar exactly coincides
Chart for adjustment with B, enter B as a value.
Figure 1-3-34

6. Press the start key after all values have been entered. Color registration correction starts.
7. Print a chart for adjustment.
8. Verify that each scale is within the range of 1to A.
The scale must be corresponding

within the range of "A" from "1".
Figure 1-3-35
1-3-176
2LK/2LN/2LM/2LC

U469 Method: [Belt Initialize]
2. Press the start key. Transfer belt speed correction starts.
Completion
U474 Checking LSU cleaning operation
Description
Provides cleaning LSU by means of the LSU cleaning motor. Also, the cleaning cycle can be
adjusted.
Method
2. Select the item.
Display Description
Execute Executing the cleaning operation
Cycle Setting the cleaning cycle
Method: [Execute]
1. Press the start key. Cleaning the LSU slit glass.
Setting: [Cycle]
1. Change the setting value using +/- keys.
Setting Initial
Display Description
range setting
Cycle Cleaning cycle 0 to 5000 1000
The setting can be changed by 1000 per step.
Completion
1-3-177
2LK/2LN/2LM/2LC

U485 Setting the image processing mode
Description
Sets the detection level for scanning printed matter outputted with the confidential document
guard function. Also, sets the process PDF images are rotated.
Purpose
To change the detection level when the confidential document guard is not printed well for detec-
tion in scanning. Also, changes the process of how PDF images are rotated.
Method
2. Select the item.
Display Description
Conf. Doc. Detection Confidential document guard detection level
PDF Rotation Processing the rotation of PDF images
Setting: [Conf. Doc. Detection]

1. Change the setting value using +/- keys or numeric keys.
Setting Initial
Display Description
range setting
Conf. Doc. Confidential document guard detection 1 to 5 1
Detection level
A smaller value raises the detection sensitivity but increases the possibility of false detection.
A larger value lowers the detection sensitivity but decreases the possibility of false detection.
Setting: [PDF Rotation]

1. Change the setting value using +/- keys or numeric keys.
Display Description
0 Assigns the image rotation with the internal parameter
1 Assigns the image rotation with the actual image
Initial setting: 0
Completion
1-3-178
2LK/2LN/2LM/2LC

U486 Setting color/black and white operation mode
Description
When color and B/W documents are mixed, sets operation mode after a color document is
detected.
Purpose
To ensure productivity when copying color and B/W documents in ACS mode, select Mode3.
However, selecting Mode3 will increase the maintenance count for cyan, magenta, and yellow
color developer units even when there is a B/W original after a color original.
Setting
2. Select the mode.
Display Description
Mode1 Line speed: Color and B/W line speed is switched according to each original
Controlling developer motor MCY: Color and B/W mode is switched accord-
ing to each original
Mode2 Line speed: Fixed at color line speed
Controlling developer motor MCY: Color and B/W mode is switched accord-
ing to each original
Mode3 Line speed: Fixed at color line speed on and after a color original
Controlling developer motor MCY: Fixed at color mode on and after a color
original
Auto Automatic selection of Mode1 to 3 depending on the using pattern
Completion
1-3-179
2LK/2LN/2LM/2LC

U901 Checking copy counts by paper feed locations
Description
Displays or clears paper feed counts by paper feed locations.
Purpose
To check the time to replace consumable parts. Also to clear the counts after replacing the con-
sumable parts.
Method
1. Press the start key. The counts by paper feed locations are displayed.
Display Description
MPT MP tray
Cassette5 Cassette 5 (SMT paper feeder/side feeder)
Duplex Duplex unit
* : When an optional paper feed device is not installed, the corresponding count is not dis-
played.
Clearing
1. Select the counts to be cleared.
[Cassette3], [Cassette4], [Cassette5], [Cassette6] and [Cassette7] cannot be cleared.
2. Select the counts for all and press [Clear].
3. Press the start key. The counts is cleared.
Completion
1-3-180
2LK/2LN/2LM/2LC

U903 Checking/clearing the paper jam counts
Description
Displays or clears the jam counts by jam locations.
Purpose
To check the paper jam status. Also to clear the jam counts after replacing consumable parts.
Method
2. Select the item.
Display Description
Cnt Displays/clears the jam counts
Total Cnt Displays the total jam counts
Method: [Cnt]
1. Select [Cnt]. The count of jam code by type is displayed.
Codes for which the count value is 0 are not displayed.
3. Select the count value for jam code and press [Clear].
The individual counter cannot be cleared.
Method: [Total Cnt]

1. Select [Total Cnt]. The total number of jam code by type is displayed.
The total number of jam count cannot be cleared.
Completion
1-3-181
2LK/2LN/2LM/2LC

U904 Checking/clearing the call for service counts
Description
Displays or clears the service call code counts by types.
Purpose
To check the service call code status by types.
Also to clear the service call code counts after replacing consumable parts.
Method
2. Select the item.
Display Description
Cnt Displays/clears the call for service counts
Total Cnt Displays the total call for service counts
Method: [Cnt]
1. Select [Cnt]. The count for service call detection by type is displayed.
Codes for which the count value is 0 are not displayed.
3. Select the count value for service call code and press [Clear].
The individual counter cannot be cleared.
Method: [Total Cnt]

1. Select [Total Cnt]. The total number of service call counts by type is displayed.
The total number of service call count cannot be cleared.
Completion
1-3-182
2LK/2LN/2LM/2LC

U905 Checking counts by optional devices
Description
Displays the counts of DP, 1000-sheet or 4000-sheet finisher.
Purpose
To check the use of DP, 1000-sheet or 4000-sheet finisher.
Method
2. Select the device, the count of which is to be checked.
The count of the selected device is displayed.
Display Description
DP Counts of DP
DF Counts of 1000-sheet or 4000-sheet finisher
Method: [DP]
Display Description
ADP No. of single-sided originals that has passed through the DP
RADP No. of double-sided originals that has passed through the DP
CIS No. of dual scan originals that has passed through the DP
Method: [DF]
Display Description
Sorter No. of copies that has passed
Staple Frequency the stapler has been activated
Punch Frequency the punch has been activated
Stack* Frequency the stacker has been activated
Saddle* Frequency the saddle eject has been activated
Fold* Frequency the center folding has been activated
Three Fold* Frequency the tri-folding has been activated
* : 4000-sheet finisher only
Completion
1-3-183
2LK/2LN/2LM/2LC

U906 Resetting partial operation control
Description
Resets the service call code for partial operation control.
Purpose
To be reset after partial operation is performed due to problems in the cassettes or other sec-
tions, and the related parts are serviced.
Method
2. Press [Execute].
3. Press the start key to reset partial operation control.
U908 Checking the total counter value
Description
Displays the total counter value.
Purpose
To check the total counter value.
Method
1. Press the start key. The total count value is displayed.
Completion
U910 Clearing the print coverage data
Description
Clears the accumulated data for the print coverage per A4 size paper.
Purpose
To clear data as required at times such as during maintenance service.
Method
3. Press the start key. The print coverage data is cleared.
Completion
1-3-184
2LK/2LN/2LM/2LC

U911 Checking copy counts by paper sizes
Description
Displays the paper feed counts by paper sizes.
Purpose
To check the counts after replacing consumable parts.
Method
1. Press the start key. The screen for the paper feed counts by paper size is displayed.
Display Display
Description Description
(metric) (inch)
A3 Paper feed counts for A3 Ledger Paper feed counts for Ledger
B4 Paper feed counts for B4 Legal Paper feed counts for Legal
A4 Paper feed counts for A4 Letter Paper feed counts for Letter
B5 Paper feed counts for B5 Statement Paper feed counts for State-
ment
A5 Paper feed counts for A5
Folio Paper feed counts for Folio ETC Paper feed counts for other
size
ETC Paper feed counts for other
size
Clearing
1. Select the paper size of counts to be cleared.
Completion
1-3-185
2LK/2LN/2LM/2LC

U917 Setting backup data reading/writing
Description
Retrieves the backup data to a USB memory from the machine; or writes the data from the USB
memory to the machine.
Purpose
To store and write data when replacing the HDD.
Method
1. Press the power key on the operation panel, and after verifying the power indicator has gone
off, switch off the main power switch.
Wait for 10 seconds to allow the machine to recognize the USB memory.
5. Select [Import] or [Export].
Display Description
Import Writing data from the USB memory to the machine
Export Retrieving from the machine to a USB memory
6. Select the item.
Display Description Depending data
Address Book Address book -
Job Account Job accounting -
One Touch Information on one-touch key Address book
User User managements Job accounting
Program Program information Job accountings and user manage-
ments
Shortcut Shortcut information Job accountings, user managements
and document box information
Document Box Document box information Job accountings and user manage-
ments
Fax Forward FAX transfer information Job accountings, user managements
and document box information
* : Since data are dependent with each other, data other than those assigned are also
retrieved or written in.
7. Press the start key. Starts reading or writing.
The progress of selected item is displayed in %.
When an error occurs, the operation is canceled and an error code is displayed.
9. Turn the main power switch off and on after completing writing when selecting [Import].
1-3-186
2LK/2LN/2LM/2LC

U917 Error Codes
e002 Parameter error e31e User managements error
e003 File write error e31f User managements open error
e004 File initialization error e320 User managements error
e005 File error e321 User managements open error
e006 Processing error e322 User managements list error
e010 Address book clear error (contact) e324 Shortcut open error
e011 Address book open error (contact) e325 Shortcut list error
e012 Address book list error (contact) e410 Box file open error
e013 Address book list error (contact) e411 Box error in writing
e014 Address book clear error (group) e412 Box error in reading
e015 Address book open error (group) e413 Box list error
e016 Address book list error (group) e414 Box list error
e017 Address book list error (group) e415 Box error
e110 Job accounting clear error e416 Box error
e111 Job accounting open error e417 Box open error
e112 Job accounting open error e418 Box close error
e113 Job accounting error in writing e419 Box creation error
e114 Job accounting list error e41a Box creation error
e115 Job accounting list error e41b Box deletion error
e210 One-touch open error e41c Box movement error
e211 One-touch list error e510 Program error in writing
e212 One-touch list error e511 Program error in reading
e310 User managements backup error e610 Shortcut error in writing
e311 User managements clear error e611 Shortcut error in reading
e312 User managements open error e710 Fax memory open error
e313 User managements open error e711 Fax memory initialization error
e314 User managements open error e712 Fax memory list error
e315 User managements error in writing e713 Fax memory error
e316 User managements list error e714 Fax memory error
e317 User managements list error e715 Fax memory mode error
e31a User managements open error e718 Fax memory mode error
e31b User managements error e910 File reading error
e31c User managements error e911 File writing error
e31d User managements open error e912 Data mismatch
1-3-187
2LK/2LN/2LM/2LC

U917 Error Codes
e913 Log file open error d008 File rename error
e914 Log file error in writing d009 File open error
e915 Directory open error d00a File close error
e916 Directory error in reading d00b File reading error
e917 Synchronization error d00c File writing error
e918 Synchronization error d00d File copy error
d000 Unspecified error d00e File compressed error
d001 HDD unavailable d00f File decompressed error
d002 USB memory is not inserted d010 Directory open error
d003 File for writing is not found in the USB d011 Directory creation error
d004 File for reading is not found in the HDD d012 File writing error
d005 USB error in writing d013 File reading error
d006 USB error in reading d014 File deletion error
d007 USB unmount error d015 File copy error to the USB
Completion
1-3-188
2LK/2LN/2LM/2LC

U920 Checking the copy counts
Description
Checks the copy counts.
Purpose
To check the copy counts.
Method
1. Press the start key. The current counts are displayed.
Display Description
Color Copy(H) Count value of full color copy (coverage: high)
Color Copy(M) Count value of full color copy (coverage: middle)
Color Copy(L) Count value of full color copy (coverage: low)
Mono Color Copy Count value of single color copy
B/W Copy Count value of black/white copy
Color Prn(H) Count value of full color print (coverage: high)
Color Prn(M) Count value of full color print (coverage: middle)
Color Prn(L) Count value of full color print (coverage: low)
B/W Prn Count value of black/white print
B/W Fax Count value of black/white FAX
Completion
U927 Clearing the all copy counts and machine life counts (one time only)
Description
Resets all of the counts back to zero.
Supplement
The total account counter and the machine life counter can be cleared only once if all count val-
ues are 1000 or less.
Method
3. Press the start key. All copy counts and machine life counts are cleared.
Completion
1-3-189
2LK/2LN/2LM/2LC

U928 Checking machine life counts
Description
Displays the machine life counts.
Purpose
To check the machine life counts.
Method
1. Press the start key. The current machine life counts is displayed.
Display Description
Cnt Machine life counts
Completion
U930 Checking/clearing the charger roller count
Description
Displays the counts of the charger roller counter for checking or clearing.
Purpose
To check the count after replacement of the charger roller unit. To clear the counter value when
replacing the charger roller unit.
Method
1. Press the start key. The current counts of the charger roller count for each color is displayed.
Display Description
C Count value of cyan charger roller
M Count value of magenta charger roller
Y Count value of yellow charger roller
K Count value of black charger roller
Clearing
1. Select the counts to be cleared.
2. Select the counts for all and press [Clear].
Completion
1-3-190
2LK/2LN/2LM/2LC

U942 Setting of deflection for feeding from DP
Description
Adjusts the deflection generated when the document processor is used.
Purpose
Use this mode if an original non-feed jam, oblique feed or wrinkling of original occurs when the
document processor is used.
Setting
6. Change the setting value using the +/- keys or numeric keys.l
Display Description
Front Deflection of single-sided original -31 to 31 0 0.31 mm
Back Deflection of double-sided original -31 to 31 0 0.31 mm
* : The greater the value, the larger the deflection; the smaller the value, the smaller the
deflection.
If an original non-feed jam or oblique feed occurs, increase the setting value. If wrinkling
of original occurs, decrease the value.
Completion
1-3-191
2LK/2LN/2LM/2LC

U952 Maintenance mode workflow
Description
The maintenance modes configured in the machine or a USB flash device as a workflow must be
executed in succession.
Purpose
This allows maintenance mode to be preset as a template.
Setting
2. Select the item.
Display Description
Continue Restarting an abandoned workflow
Execute(USB) Executes a workflow housed in a USB flash device
Execute Executes a worlflow stored in the machine
Entry(USB) Exports a workflow housed in a USB flash device to the machine
Entry Assigns a workflow in the machine manually
Log Displays a list of workflows recently executed
Method: [Execute]
2. Select the workflow.
Display Description
Data1 - 6 The area to store workflows in the machine
Executes maintenance modes defined in a workflow in sccession.
Method: [Entry]
1. Select [Entry].
2. Select the area to store workflow.
Display Description
3. Press the +/- keys or numeric keys to assign a maintenance Nbr. into a workflow.
Display Description
Flow1 - 14 Assign a maintenance Nbr.
1-3-192
2LK/2LN/2LM/2LC

U952 Method: [Execute(USB)]
5. Select [Execute(USB)].
Display Description
WorkFlowData01 - 07 Workflow data in the USB flash device
Method: [Entry(USB)]
5. Select [Entry(USB)].
Display Description
WorkFlowData01 - 07 Workflow data in the USB flash device
7. Select the work flow save area.
Display Description
Exports a workflow housed in a USB flash device to the machine.
Completion
1-3-193
2LK/2LN/2LM/2LC

U964 Checking of log
Description
Sends a log file saved on the HDD to a USB memory.
Purpose
To transfer a log file saved on the HDD to a USB memory as a means of investigating malfunc-
tions.
Method
Starts sending the log file saved on the HDD to the USB memory.
If a problem occurs during auto correction, error code is displayed.
Error codes
Display Description
No Usb Storage USB memory is not inserted
No File File is not found
Mount Error USB memory mount error
File Delete Error File deletion error
Copy Error File copy error
Unmount Error USB memory unmount error
Other Error Other error
U969 Checking of toner area code
Description
Displays the toner area code.
Purpose
To check the toner area code.
Method
1. Press the start key. The toner area code is displayed.
Completion
Press the stop/clear key. The screen for selecting a maintenance item No. is displayed.
1-3-194
2LK/2LN/2LM/2LC

U977 Data capture mode
Description
Store the print data sent to the machine into USB memory.
Purpose
In case to occur the error at printing, check the print data sent to the machine.
Method
7. Send the print data to the machine.
Once the print data is stored into USB memory, [Finish] will be displayed.
Completion
U984 Checking the developer unit number
Description
Displays the developer unit number.
Purpose
To check the developer unit number.
Method
1. Press the start key. The developer unit number for each color is displayed.
Display Description
C Cyan developer unit number
M Magenta developer unit number
Y Yellow developer unit number
K Black developer unit number
Completion
1-3-195
2LK/2LN/2LM/2LC

U985 Displaying the developer unit history
Description
Displays the past record of machine number and the developer counter.
Purpose
To check the count value of machine number and the developer counter.
Method
2. Select the color to check.
Display Description
C Cyan developer unit past record
M Magenta developer unit past record
Y Yellow developer unit past record
K Black developer unit past record
The history of a machine number and a developer counter for each color is displayed by
three cases.
Display Description
Cnt History1 - 3 Historical records of developer counter
Completion
U989 HDD Scandisk
Description
Restores data in the hard disk by scanning the disk.
Purpose
If power is turned off while accessing to the hard disk is performed, the control information in the
hard disk drive may be damaged. Use this mode to restore the data.
Method
3. Press the start key. When scanning of the disk is complete, the execution result is displayed.
1-3-196
2LK/2LN/2LM/2LC

U990 Checking the time for the exposure lamp to light
Description
Displays the accumulated time for the CIS to light.
Purpose
To check duration of use of the CIS.
Method
The accumulated time for the CIS to light is displayed in minutes.
Display Description
CIS The accumulated time for the CIS to light
Completion
U991 Checking the scanner operation count
Description
Displays the scanner operation count.
Purpose
To check the status of use of the scanner.
Method
1. Press the start key. The current operation counts is displayed.
Display Description
Copy Scan Scanner operation counts for copying
Fax Scan Scanner operation counts for fax
Other Scan Scanner operation counts except for copying
Completion
Press the stop key. The screen for selecting a maintenance No. item is displayed.
1-3-197
2LK/2LN/2LM/2LC
1-3-198
2LK/2LN/2LM/2LC
1-4-1 Paper misfeed detection

1-4 Troubleshooting
(1) Paper misfeed indication

When a paper misfeed occurs, the machine immediately stops printing and displays the paper misfeed mes-
sage on the operation panel. To remove paper misfed in the machine, pull out the cassette, open the paper
conveying unit or paper conveying cover.
H
K K I
K J I G G
K
K E
F
D
A L
E L
B L
C C M M M
E
K C
K M
Figure 1-4-1 Paper misfeed indication
A. Misfeed in cassette 1
B. Misfeed in cassette 2
C. Misfeed in cassette 3 or 4 (option)
D. Misfeed in the MP tray
E. Misfeed in paper conveying unit, paper conveying
cover or PF paper conveying cover
F. Misfeed in the duplex section
G. Misfeed in the fuser section
H. Misfeed in document processor (option)
I. Misfeed in job separator (option)
J. Misfeed in bridge unit (option)
K. Misfeed in document finisher (option)
L. Misfeed in cassette 5 (option)
M. Misfeed in cassette 6 or 7 (option)
1-4-1
2LK/2LN/2LM/2LC
(2) Paper misfeed detection condition
Machine
SBS
EFS
DUS1
FUES
LPS
DUS2
RS
MS
MPFS
FS1
PCS1
FS2
PCS2
Figure 1-4-2 Paper jam location
1-4-2
2LK/2LN/2LM/2LC
Jam
Code Contents Conditions
location*
0000 Initial jam The power is turned on when a sensor in the con- -
veying system is on.
0100 Secondary paper feed request Secondary paper feed request given by the con- -
time out troller is unreachable.
0101 Waiting for process package Process package won’t become ready. -
to become ready
0102 Waiting for toner package to Toner package won’t become ready. -
become ready
0103 Waiting for the image-sustain- The image-sustaining package won’t become -
ing package to become ready ready.
0104 Waiting for conveying pack- Conveying package won’t become ready. -
age to become ready
0105 Registration sensor not Activation of the registration sensor (on/off) is -
detected undetected for 90 s during printing.
0106 Paper feeding request for Paper feeding request for duplex printing given by -
duplex printing time out the controller is unreachable.
0107 Waiting for fuser package to Fuser package won’t become ready. -
become ready
0108 Waiting for option package to Option package won’t become ready. -
become ready
0110 Paper conveying unit open The paper conveying unit is opened during print- E
ing.
0111 Front cover open The front cover is opened during printing. -
0112 Duplex cover open The duplex cover is opened during printing. F
0113 Paper conveying cover open The paper conveying cover is opened during E
printing.
0114 Bridge cover open The bridge cover is opened during printing. J
0115 Bridge eject cover open The bridge eject cover is opened during printing. J
0120 Receiving a duplex paper Paper feed request was received from the duplex F
feeding request while paper is section despite the absence of paper in the
empty duplex section.
0121 Exceeding number of duplex The controller issued the duplex section a request F
pages circulated for more pages than the duplex print cycle con-
tains.
0131 MP lift sensor upper limit MP lift sensor 1 (DPLS1) does not turn on within D
detection specified time of the MP lift plate rising.
0200 Machine sequence error A sequence error has caused. -
0210 PF paper conveying cover The PF paper conveying cover is opened during E
open printing.
0211 Paper conveying cover open The paper conveying cover is opened during E
printing.
*: Refer to figure 1-4-1 for paper misfeed indication (see page 1-4-1).
1-4-3
2LK/2LN/2LM/2LC
Jam
location*
0212 SMT top cover open The SMT top cover is opened during printing. L
0213 PF paper conveying cover The PF paper conveying cover (side) is opened M
(side) open during printing.
0214 SMT paper conveying cover The SMT paper conveying cover is opened dur- L
open ing printing.
0501 No paper feed from cassette 1 Feed sensor 1 (FS1) does not turn on during A
paper feed from cassette 1.
0502 No paper feed from cassette 2 Feed sensor 2 (FS2) does not turn on during B
0503 No paper feed from cassette 3 PF feed sensor 1 (PFFS1) does not turn on dur- C
ing paper feed from cassette 3 (paper feeder).
0505 No paper feed from cassette 5 SMT feed sensor (SMTFS) does not turn on dur- L
ing paper feed from cassette 5 (SMT paper
feeder).
0506 No paper feed from cassette 6 PF feed sensor 1 (PFFS1) does not turn on dur- M
ing paper feed from cassette 6 (side paper
feeder).
feeder).
0508 No paper feed from duplex Registration sensor (RS) does not turn on during F
section paper feed from duplex section.
0509 No paper feed from MP tray MP feed sensor (MPFS) does not turn on during D
paper feed from MP tray.
0511 Multiple sheets in cassette 1 Feed sensor 1 (FS1) does not turn off during A
0512 Multiple sheets in cassette 2 Feed sensor 2 (FS2) does not turn off during B
0513 Multiple sheets in cassette 3 PF feed sensor 1 (PFFS1) does not turn off dur- C
0515 Multiple sheets in cassette 5 SMT feed sensor (SMTFS) does not turn off dur- L
feeder).
0516 Multiple sheets in cassette 6 PF feed sensor 1 (PFFS1) does not turn off dur- M
feeder).
1-4-4
2LK/2LN/2LM/2LC
Jam
location*
feeder).
0518 Multiple sheets in duplex sec- Registration sensor (RS) does not turn off during F
tion paper feed from duplex section.
0519 Multiple sheets in MP tray MP feed sensor (MPFS) does not turn off during D
ing paper feed from cassette 3 (large capacity
feeder).
feeder).
0525 No paper feed from cassette 5 SMT feed sensor (SMTFS) does not turn on dur- L
feeder).
ing paper feed from cassette 6 (side large capac-
ity feeder).
ity feeder).
feeder).
feeder).
0535 Multiple sheets in cassette 5 SMT feed sensor (SMTFS) does not turn off dur- L
feeder).
ity feeder).
ity feeder).
0545 No paper feed from side PF feed sensor (PFFS) does not turn on during L
feeder paper feed from side feeder.
0555 Multiple sheets in side feeder PF feed sensor (PFFS) does not turn off during L
paper feed from side feeder.
1-4-5
2LK/2LN/2LM/2LC
Jam
location*
1301 Middle sensor non arrival jam Middle sensor (MS) does not turn on during paper A
feed from cassette 1.
1302 Middle sensor (MS) does not turn on during paper B
1303 Middle sensor (MS) does not turn on during paper C
feed from cassette 3 (paper feeder).
1304 Middle sensor (MS) does not turn on during paper C
1311 Middle sensor stay jam Middle sensor (MS) does not turn off during paper E
1312 Middle sensor (MS) does not turn off during paper E
1502 Paper conveying sensor non Paper conveying sensor (PCS) does not turn on B
arrival jam during paper feed from cassette 2.
1503 Paper conveying sensor (PCS) does not turn on C
during paper feed from cassette 3 (paper feeder).
1504 Paper conveying sensor (PCS) does not turn on C
1512 Paper conveying sensor stay Paper conveying sensor (PCS) does not turn off E
jam during paper feed from cassette 2.
1513 Paper conveying sensor (PCS) does not turn off E
1514 Paper conveying sensor (PCS) does not turn off E
1703 PF paper conveying sensor 1 PF paper conveying sensor 1 (PFPCS1) does not C
non arrival jam turn on during paper feed from cassette 3 (paper
feeder).
1704 PF paper conveying sensor 1 (PFPCS1) does not C
turn on during paper feed from cassette 4 (paper
feeder).
1713 PF paper conveying sensor 1 PF paper conveying sensor 1 (PFPCS1) does not E
stay jam turn off during paper feed from cassette 3 (paper
feeder).
1714 PF paper conveying sensor 1 (PFPCS1) does not E
turn off during paper feed from cassette 4 (paper
feeder).
1-4-6
2LK/2LN/2LM/2LC
Jam
location*
non arrival jam turn on during paper feed from cassette 4 (paper
feeder).
stay jam turn off during paper feed from cassette 4 (paper
feeder).
2106 PF paper conveying sensor 1 PF paper conveying sensor 1 (PFPCS1) does not M
non arrival jam turn on during paper feed from cassette 6 (side
paper feeder).
2107 PF paper conveying sensor 1 (PFPCS1) does not M
turn on during paper feed from cassette 7 (side
paper feeder).
2116 PF paper conveying sensor 1 PF paper conveying sensor 1 (PFPCS1) does not L
stay jam turn off during paper feed from cassette 6 (side
paper feeder).
2117 PF paper conveying sensor 1 (PFPCS1) does not L
turn off during paper feed from cassette 7 (side
paper feeder).
paper feeder).
paper feeder).
non arrival jam turn on during paper feed from cassette 3 (large
capacity feeder).
2604 PF paper conveying sensor 1 (PFPCS1) does not C
turn on during paper feed from cassette 4 (large
capacity feeder).
stay jam turn off during paper feed from cassette 3 (large
capacity feeder).
2614 PF paper conveying sensor 1 (PFPCS1) does not E
turn off during paper feed from cassette 4 (large
capacity feeder).
non arrival jam turn on during paper feed from cassette 4 (large
capacity feeder).
stay jam turn off during paper feed from cassette 4 (large
capacity feeder).
1-4-7
2LK/2LN/2LM/2LC
Jam
location*
large capacity feeder).
3107 PF paper conveying sensor 1 (PFPCS1) does not M
3117 PF paper conveying sensor 1 (PFPCS1) does not L
3405 SMT paper conveying sensor SMT paper conveying sensor 1 (SMTPCS1) does L
1 non arrival jam not turn on during paper feed from cassette 5
(SMT paper feeder).
3406 SMT paper conveying sensor 1 (SMTPCS1) does M
not turn on during paper feed from cassette 6
(SMT paper feeder).
(SMT paper feeder).
1 stay jam not turn off during paper feed from cassette 5
(SMT paper feeder).
3416 SMT paper conveying sensor 1 (SMTPCS1) does L
not turn off during paper feed from cassette 6
(SMT paper feeder).
(SMT paper feeder).
1-4-8
2LK/2LN/2LM/2LC
Jam
location*
(SMT paper feeder).
(SMT paper feeder).
(SMT paper feeder).
(SMT paper feeder).
(SMT paper feeder).
(SMT paper feeder).
(SMT paper feeder).
(SMT paper feeder).
(SMT paper feeder).
(SMT paper feeder).
(SMT paper feeder).
(SMT paper feeder).
1-4-9
2LK/2LN/2LM/2LC
Jam
location*
(SMT paper feeder).
(SMT paper feeder).
(SMT paper feeder).
(SMT paper feeder).
(SMT paper feeder).
(SMT paper feeder).
4001 Registration sensor non Registration sensor (RS) does not turn on during E
arrival jam paper feed from cassette 1.
4002 Registration sensor (RS) does not turn on during E
paper feed from cassette 3 (paper feeder).
paper feed from cassette 5 (SMT paper feeder).
paper feed from cassette 6 (side paper feeder).
paper feed from duplex section.
1-4-10
2LK/2LN/2LM/2LC
Jam
location*
4011 Registration sensor stay jam Registration sensor (RS) does not turn off during E
4012 Registration sensor (RS) does not turn off during E
4101 Loop sensor non arrival jam Loop sensor (LPS) does not turn on during paper E
4102 Loop sensor (LPS) does not turn on during paper E
feed from cassette 5 (SMT paper feeder).
feed from cassette 6 (side paper feeder).
feed from duplex section.
feed from MP tray.
1-4-11
2LK/2LN/2LM/2LC
Jam
location*
4111 Loop sensor stay jam Loop sensor (LPS) does not turn off during paper E
4112 Loop sensor (LPS) does not turn off during paper E
feed from cassette 5 (SMT paper feeder).
feed from duplex section.
feed from MP tray.
4201 Fuser eject sensor non arrival Fuser eject sensor (FUES) does not turn on dur- E
jam ing paper feed from cassette 1.
4202 Fuser eject sensor (FUES) does not turn on dur- E
ing paper feed from cassette 2.
feeder).
feeder).
feeder).
ing paper feed from duplex section.
ing paper feed from MP tray.
1-4-12
2LK/2LN/2LM/2LC
Jam
location*
4211 Fuser eject sensor stay jam Fuser eject sensor (FUES) does not turn off dur- G
4212 Fuser eject sensor (FUES) does not turn off dur- G
feeder).
feeder).
feeder).
4301 Duplex sensor 1 non arrival Duplex sensor 1 (DUS1) does not turn on during G
jam paper feed from cassette 1.
4302 Duplex sensor 1 (DUS1) does not turn on during G
1-4-13
2LK/2LN/2LM/2LC
Jam
location*
4311 Duplex sensor 1 stay jam Duplex sensor 1 (DUS1) does not turn off during F
4312 Duplex sensor 1 (DUS1) does not turn off during F
4401 Duplex sensor 2 non arrival Duplex sensor 2 (DUS2) does not turn on during F
4402 Duplex sensor 2 (DUS2) does not turn on during F
1-4-14
2LK/2LN/2LM/2LC
Jam
location*
4411 Duplex sensor 2 stay jam Duplex sensor 2 (DUS2) does not turn off during F
4601 Eject full sensor non arrival Eject full sensor (EFS) does not turn on during G
4602 Eject full sensor (EFS) does not turn on during G
1-4-15
2LK/2LN/2LM/2LC
Jam
location*
4611 Eject full sensor stay jam Eject full sensor (EFS) does not turn off during G
4612 Eject full sensor (EFS) does not turn off during G
4701 Switchback sensor non arrival Switchback sensor (SBS) does not turn on during G
4702 Switchback sensor (SBS) does not turn on during G
1-4-16
2LK/2LN/2LM/2LC
Jam
location*
4711 Switchback sensor stay jam Switchback sensor (SBS) does not turn off during I
4712 Switchback sensor (SBS) does not turn off during I
4901 Bridge conveying sensor 1 Bridge conveying sensor 1 (BRCS1) does not G
non arrival jam turn on during paper feed from cassette 1.
4902 Bridge conveying sensor 1 (BRCS1) does not G
turn on during paper feed from cassette 2.
feeder).
feeder).
turn on during paper feed from cassette 5 (SMT
paper feeder).
paper feeder).
paper feeder).
turn on during paper feed from duplex section.
turn on during paper feed from MP tray.
1-4-17
2LK/2LN/2LM/2LC
Jam
location*
4911 Bridge conveying sensor 1 Bridge conveying sensor 1 (BRCS1) does not J
stay jam turn off during paper feed from cassette 1.
4912 Bridge conveying sensor 1 (BRCS1) does not J
turn off during paper feed from cassette 2.
feeder).
feeder).
turn off during paper feed from cassette 5 (SMT
paper feeder).
paper feeder).
paper feeder).
turn off during paper feed from duplex section.
turn off during paper feed from MP tray.
non arrival jam turn on during paper feed from cassette 1.
turn on during paper feed from cassette 2.
feeder).
feeder).
turn on during paper feed from cassette 5 (SMT
paper feeder).
paper feeder).
paper feeder).
1-4-18
2LK/2LN/2LM/2LC
Jam
location*
non arrival jam turn on during paper feed from duplex section.
turn on during paper feed from MP tray.
stay jam turn off during paper feed from cassette 1.
turn off during paper feed from cassette 2.
feeder).
feeder).
turn off during paper feed from cassette 5 (SMT
paper feeder).
paper feeder).
paper feeder).
turn off during paper feed from duplex section.
turn off during paper feed from MP tray.
5101 Bridge eject sensor non Bridge eject sensor (BRES) does not turn on dur- J
arrival jam ing paper feed from cassette 1.
5102 Bridge eject sensor (BRES) does not turn on dur- J
feeder).
feeder).
1-4-19
2LK/2LN/2LM/2LC
Jam
location*
5107 Bridge eject sensor non Bridge eject sensor (BRES) does not turn on dur- J
arrival jam ing paper feed from cassette 7 (side paper
feeder).
5111 Bridge eject sensor stay jam Bridge eject sensor (BRES) does not turn off dur- J
5112 Bridge eject sensor (BRES) does not turn off dur- J
feeder).
feeder).
feeder).
6000 DF paper entry error DF paper entry sensor (DFPES) turns on before K
the eject signal is output from the machine (4000-
sheet finisher).
6001 DF paper entry sensor (DFPES) turns on before K
the eject signal is output from the machine (1000-
sheet finisher).
6020 DF front cover open DF front upper cover is opened during operation K
(4000-sheet finisher)
6021 DF front cover is opened during operation (1000- K
sheet finisher)
6041 DF top cover open DF top cover is opened during operation (1000- K
sheet finisher)
6050 CF eject cover open CF eject cover is opened during operation (4000- K
sheet finisher)
1-4-20
2LK/2LN/2LM/2LC
Jam
location*
6060 MB cover open MB cover is opened during operation (4000-sheet K
finisher)
6070 Center folding unit open Center folding unit is opened during operation K
(4000-sheet finisher)
6080 CF left guide open CF left guide is opened during operation (4000- K
sheet finisher)
6100 DF paper entry sensor non DF paper entry sensor (DFPES) is not turned on K
arrival jam even if a specified time has elapsed after the
machine eject signal was received (4000-sheet
finisher).
6101 DF paper entry sensor (DFPES) is not turned on K
even if a specified time has elapsed after the
machine eject signal was received (1000-sheet
finisher).
6110 DF paper entry sensor stay DF paper entry sensor (DFPES) is not turned off K
jam within specified time of its turning on (4000-sheet
finisher).
6111 DF paper entry sensor (DFPES) is not turned off K
within specified time of its turning on (1000-sheet
finisher).
6120 DF paper entry sensor DF paper entry sensor (DFPES) does turned on K
remaining jam when the power is turned on or cover close
(4000-sheet finisher).
6121 DF paper entry sensor (DFPES) does turned on K
when the power is turned on or cover close
6200 DF sub eject sensor non DF sub eject sensor (DFSES) does not turn on K
arrival jam within specified time of DF paper entry sensor
(DFPES) turning on.
6210 DF sub eject sensor stay jam DF sub eject sensor (DFSES) is not turned off K
within specified time of its turning on.
6220 DF sub eject sensor remain- DF sub eject sensor (DFSES) does turned on K
ing jam when the power is turned on or cover close.
6300 DF middle eject sensor non DF middle eject sensor (DFMES) does not turn K
arrival jam on within specified time of DF paper entry sensor
(DFPES) turning on (4000-sheet finisher).
6301 DF middle eject sensor (DFMES) does not turn K
on within specified time of DF paper entry sensor
(DFPES) turning on (1000-sheet finisher).
1-4-21
2LK/2LN/2LM/2LC
Jam
location*
6310 DF middle eject sensor stay DF middle eject sensor (DFMES) is not turned off K
jam within specified time of its turning on (4000-sheet
finisher).
6311 DF middle eject sensor (DFMES) is not turned off K
within specified time of its turning on (1000-sheet
finisher).
6320 DF middle eject sensor DF middle eject sensor (DFMES) does turned on K
remaining jam when the power is turned on or cover close
6321 DF middle eject sensor (DFMES) does turned on K
when the power is turned on or cover close
6400 DF tray upper surface sensor DF tray upper surface sensor (DFTUSS) does not K
non arrival jam turn on within specified time of DF middle eject
sensor (DFMES) turning on (4000-sheet finisher).
6401 DF tray upper surface sensor (DFTUSS) does not K
turn on within specified time of DF middle eject
sensor (DFMES) turning on (1000-sheet finisher).
6410 DF tray upper surface sensor DF tray upper surface sensor (DFTUSS) is not K
stay jam turned off within specified time of its turning on
6411 DF tray upper surface sensor (DFTUSS) is not K
turned off within specified time of its turning on
6420 DF tray upper surface sensor DF tray upper surface sensor (DFTUSS) does K
remaining jam turned on when the power is turned on or cover
close (4000-sheet finisher).
6421 DF tray upper surface sensor (DFTUSS) does K
turned on when the power is turned on or cover
close (1000-sheet finisher).
6500 DF bundle discharge sensor DF bundle discharge sensor (DFBDS) does not K
non arrival jam turn on within specified time of DF middle eject
sensor (DFMES) turning on.
6510 DF bundle discharge sensor DF bundle discharge sensor (DFBDS) is not K
stay jam turned off since the bundle discharge starts
6511 DF bundle discharge sensor (DFBDS) is not K
turned off since the bundle discharge starts
6600 DF drum sensor non arrival DF drum sensor (DFDRS) does not turn on within K
jam specified time of DF paper entry sensor (DFPES)
turning on.
1-4-22
2LK/2LN/2LM/2LC
Jam
location*
6610 DF drum sensor stay jam DF drum sensor (DFDRS) is not turned off within K
specified time of its turning on.
6620 DF drum sensor remaining DF drum sensor (DFDRS) does turned on when K
jam the power is turned on or cover close.
6710 Center folding unit stay jam During paper conveying to center folding unit, DF K
drum sensor (DFDRS) is not turned off within
6810 DF side registration sensor 1 DF side registration sensor 1 (DFSRS1) is not K
stay jam turned off within specified time after driving the
DF side registration motor 1 (DFSRM1) (4000-
sheet finisher).
6811 DF side registration sensor 1 (DFSRS1) is not K
turned off within specified time after driving the
sheet finisher).
6910 DF side registration sensor 2 DF side registration sensor 2 (DFSRS2) is not K
stay jam turned off within specified time after driving the
sheet finisher).
6811 DF side registration sensor 2 (DFSRS2) is not K
turned off within specified time after driving the
sheet finisher).
7000 DF staple operation error DF staple sensor (DFSTS) is not turned on within K
specified time after driving the DF staple motor
(DFSTM) (4000-sheet finisher).
7001 DF staple sensor (DFSTS) is not turned on within K
specified time after driving the DF staple motor
(DFSTM) (1000-sheet finisher).
7100 CF paper entry sensor non CF paper entry sensor (CFPES) is not turned on K
arrival jam even if a specified time has elapsed after the
machine eject signal was received.
7110 CF paper entry sensor stay CF paper entry sensor (CFPES) is not turned off K
jam within specified time of its turning on.
7120 CF paper entry sensor CF paper entry sensor (CFPES) does turned on K
remaining jam when the power is turned on or cover close.
7200 CF eject sensor non arrival CF eject sensor (CFES) is not turned on within K
jam specified time since centerfold operation starts.
7210 CF eject sensor stay jam During centerfold operation, CF eject sensor K
(CFES) is not turned off within specified time of its
turning on.
7220 CF eject sensor remaining CF eject sensor (CFES) does turned on when the K
jam power is turned on or cover close.
1-4-23
2LK/2LN/2LM/2LC
Jam
location*
7300 CF eject sensor non arrival CF eject sensor (CFES) is not turned on within K
jam specified time since three fold operation starts.
7310 CF eject sensor stay jam During three fold operation, CF eject sensor K
(CFES) is not turned off within specified time of its
turning on.
7400 CF side registration sensor 2 CF side registration sensor 2 (CFSRS2) is not K
non arrival jam turned on within specified time after driving the
CF side registration motor 2 (CFSRM2).
7500 CF side registration sensor 1 CF side registration sensor 1 (CFSRS1) is not K
non arrival jam turned on within specified time after driving the
CF side registration motor 1 (CFSRM1).
7600 CF staple operation error CF staple sensor (CFSTS) is not turned on within K
specified time after driving the CF staple motor
(CFSTM).
7720 CF paper sensor remaining CF paper sensor (CFPS) does turned on when K
7800 MB eject sensor non arrival MB eject sensor (MBES) is not turned on even if K
jam a specified time has elapsed after the machine
eject signal was received.
7810 MB eject sensor stay jam MB eject sensor (MBES) is not turned off within K
7820 MB eject sensor remaining MB eject sensor (MBES) does turned on when K
7950 Paper interval error jam An illegal inter-page or inter-copy interval has K
occurred (4000-sheet finisher).
7951 An illegal inter-page or inter-copy interval has K
occurred (1000-sheet finisher).
9000 No original feed DP feed sensor (DPFS) does not turn on within H
specified time during the first sheet feeding (Retry
5 times).
9001 DP original conveying jam DP timing sensor (DPTS) turns off within the H
specified time since the sensor turns on.
9002 DP sensor stay jam Sensor in the conveying system is on since origi- H
nal feeding starts.
9004 DP switchback jam 2 DP registration sensor (DPRS) is not turned on H
within specified time since original switchback
operation starts.
9005 No original feed 2 DP lift sensor 1 (DPLS1) does not turn on within H
specified time of the lift plate rising.
9008 No original feed 3 DP CIS sensor (DPCS) does not turn on within H
specified time of the paper feed starting.
9009 DP original conveying jam 2 Next feed original became the stand-by states of H
paper feed while reading the image.
1-4-24
2LK/2LN/2LM/2LC
Jam
location*
9010 Document processor open Document processor is opened during original H
feeding.
9011 DP top cover open The DP top cover is opened during original feed- H
ing.
9020 Original skew feed jam DP skew sensor (DPSS) does not turn on within H
specified time of DP registration sensor (DPRS)
turning on.
9110 DP feed sensor stay jam DP feed sensor (DPFS) does not turn off within H
specified time of DP timing sensor (DPTS) turning
on.
9200 DP registration sensor non DP registration sensor (DPRS) does not turn on H
arrival jam within specified time of DP feed sensor (DPFS)
turning on.
9210 DP registration sensor stay DP registration sensor (DPRS) does not turn off H
jam within specified time of DP timing sensor (DPTS)
turning on.
9300 DP CIS sensor non arrival jam DP CIS sensor (DPCS) does not turn on within H
turning on.
9310 DP CIS sensor stay jam DP CIS sensor (DPCS) does not turn off within H
turning off.
9400 DP timing sensor non arrival DP timing sensor (DPTS) does not turn on within H
jam specified time during original feeding (Retry 5
times).
9410 DP timing sensor stay jam DP timing sensor (DPTS) does not turn off within H
specified time of DP feed sensor (DPFS) turning
off.
9500 DP switchback sensor non DP switchback sensor (DPSBS) does not turn on H
arrival jam within specified time of DP timing sensor (DPTS)
turning on.
9600 DP eject sensor non arrival DP eject sensor (DPES) does not turn on within H
jam specified time of DP timing sensor (DPTS) turning
on.
9610 DP eject sensor stay jam DP eject sensor (DPES) does not turn off within H
specified time of DP timing sensor (DPTS) turning
off.
1-4-25
2LK/2LN/2LM/2LC
1-4-2 Self-diagnostic function

(1) Self-diagnostic function
This machine is equipped with self-diagnostic function. When a problem is detected, the machine stops print-
ing and display an error message on the operation panel. An error message consists of a message prompting
a contact to service personnel and a four-digit error code indicating the type of the error.
Machine failure.
Call service.
C####
Error occurred.
Turn the main power
switch off and on.
C####
Figure 1-4-3
1-4-26
2LK/2LN/2LM/2LC
(2) Self diagnostic codes

If the part causing the problem was not supplied, use the unit including the part for replacement.
Check procedures/
Code Contents Causes
corrective measures
0030 FAX control PWB system Defective FAX con- Replace the fax control PWB and check for
error trol PWB. correct operation.
Processing with the fax soft-
ware was disabled due to a
hardware problem.
0070 FAX control PWB incompat- Defective FAX soft- Install the fax software.
ible detection error ware.
Abnormal detection of FAX Defective FAX con- Replace the fax control PWB and check for
control PWB incompatibility In
trol PWB. correct operation.
the initial communication with
the FAX control PWB, any
normal communication com-
mand is not transmitted.
0100 Backup memory device Defective flash Replace the main PWB and check for cor-
error memory. rect operation (see page 1-5-49).
Defective main Replace the main PWB and check for cor-
PWB. rect operation (see page 1-5-49).
0120 MAC address data error Defective flash Replace the main PWB and check for cor-
For data in which the MAC memory. rect operation (see page 1-5-49).
address is invalid. Defective engine Replace the engine PWB and check for cor-
0150 Backup memory read/write Improper installa- Check the installation of the EEPROM and
error (engine PWB) tion EEPROM. remedy if necessary.
Detecting engine PWB Defective engine Replace the engine PWB and check for cor-
EEPROM communication PWB. rect operation (see page 1-5-54).
error.
Device damage of Contact the Service Administrative Division.
EEPROM.
0160 Backup memory data error Data damage of Contact the Service Administrative Division.
(engine PWB) EEPROM.
Reading data from EEPROM
is abnormal.
0170 Billing counting error Data damage of Contact the Service Administrative Division.
A checksum error is detected EEPROM.
in the main and engine
Defective PWB. Replace the main PWB or the engine PWB
backup memories for the bill-
and check for correct operation (see page 1-
ing counters.
5-49, 1-5-54).
0180 Machine number mismatch Data damage of Contact the Service Administrative Division.
Machine number of main and EEPROM.
engine does not match.
1-4-27
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
0620 FAX image DIMM error DIMM installed Check if the DIMM is inserted into the socket
DIMM is not installed cor- incorrectly. on the main PWB correctly.
rectly. Defective main Replace the main PWB and check for cor-
DIMM cannot be accessed.
0630 DMA error Poor contact in the Check the connection the signal cable for
DMA transmission of image connector termi- CIS and the main PWB, and the continuity
data does not complete within nals. across the connector terminals. Repair or
the specified period of time. replace if necessary.
0640 Hard disk error Defective hard Replace the hard disk and check for correct
The hard disk cannot be disk. operation.
accessed. Defective main Replace the main PWB and check for cor-
0650 FAX image DIMM check DIMM installed Check if the DIMM is inserted into the socket
error incorrectly. on the main PWB correctly.
Improper DIMM is installed.
0800 Image processing error Defective main Replace the main PWB and check for cor-
JAM010X is detected twice. PWB. rect operation (see page 1-5-49).
0820 Fax control PWB CG ROM Defective fax soft- Install the fax software.
checksum error ware.
A checksum error occurred Defective fax con- Replace the fax control PWB and check for
with the CG ROM data of the trol PWB. correct operation.
fax control PWB.
0830 FAX control PWB flash pro- Defective FAX soft- Install the fax software.
gram area checksum error ware.
A checksum error occurred Defective FAX con- Replace the fax control PWB and check for
with the program of the FAX trol PWB. correct operation.
control PWB.
0840 Faults of RTC The battery is dis- Check visually and remedy if necessary
The time is judged to go back connected from the
based on the comparison of main PWB.
the RTC time and the current
time or five years or more PWB. rect operation (see page 1-5-49).
have passed.
0860 Fax control PWB software Defective fax soft- Install the fax software.
switch checksum error ware.
A checksum error occurred Defective fax con- Replace the fax control PWB and check for
with the software switch value trol PWB. correct operation.
of the fax control PWB.
1-4-28
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
0870 FAX control PWB to main Improper installa- Reinstall the FAX control PWB.
PWB high capacity data tion FAX control
transfer error PWB.
High-capacity data transfer
Defective FAX con- Replace the FAX control PWB or main PWB
between the FAX control PWB trol PWB or main and check for correct operation (see page 1-
and the main PWB of the PWB. 5-49).
machine was not normally
performed even if the data
transfer was retried the speci-
fied times.
0880 Program archive error Defective fax soft- Install the fax software.
When power is turned on, the ware.
compressed program in the
Defective fax con- Replace the fax control PWB and check for
Flash ROM on the fax control
PWB was not successfully
decompressed.
0890 Fax control PWB CG FONT Defective fax soft- Install the fax software.
archive error ware.
When power is turned on, the Defective fax con- Replace the fax control PWB and check for
compressed CG font in the trol PWB. correct operation.
Flash ROM on the fax control
PWB was not successfully
decompressed.
0920 Fax file system error Defective FAX con- Replace the fax control PWB and check for
The backup data is not trol PWB. correct operation.
retained for file system abnor-
mality of flash memory of the
FAX control PWB.
1000 MP lift motor error Defective MP plate Check to see if the MP plate can move
After the MP lift motor is elevation mecha- smoothly and repair it if any problem is
driven, the ON status of MP lift nism. found.
sensors 1 and 2 cannot be Defective connec- Reinsert the connector. Also check for conti-
detected for 1.5 s.
tor cable or poor nuity within the connector cable. If none,
contact in the con- replace the cable.
nector. MP lift motor and relay PWB (YC3)
Relay PWB (YC12) and feed PWB 1 (YC17)
Feed PWB 1 (YC1) and engine PWB (YC6)
Defective drive Check if the gears rotate smoothly. If not,
transmission sys- grease the bushes and gears. Check for
tem of motor. broken gears and replace if any.
Defective MP lift Replace the MP lift motor.
motor.
Defective engine Replace the engine PWB and check for cor-
1-4-29
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
1010 Lift motor 1 error Defective bottom Check to see if the bottom plate can move
After cassette 1 is inserted, lift plate elevation smoothly and repair it if any problem is
sensor 1 does not turn on mechanism in the found.
within 12 s. This error is cassette.
detected four times succes- Defective connec- Reinsert the connector. Also check for conti-
sively.played 4 times succes- tor cable or poor nuity within the connector cable. If none,
sively.
nector. Lift motor 1 and feed PWB 2 (YC3)
Defective lift motor Replace the lift motor 1.
1.
1020 Lift motor 2 error Defective bottom Check to see if the bottom plate can move
After cassette 2 is inserted, lift plate elevation smoothly and repair it if any problem is
sensor 2 does not turn on mechanism in the found.
within 12 s. This error is cassette.
detected four times succes-
Defective connec- Reinsert the connector. Also check for conti-
sively.played 4 times succes- tor cable or poor nuity within the connector cable. If none,
sively. contact in the con- replace the cable.
nector. Lift motor 2 and feed PWB 2 (YC3)
Defective lift motor Replace the lift motor 2.
2.
1-4-30
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
1030 PF lift motor 1 error Defective bottom Check to see if the bottom plate can move
(paper feeder) plate elevation smoothly and repair it if any problem is
After cassette 3 is inserted, mechanism in the found.
PF lift sensor 1 does not turn cassette.
on within 12 s. This error is Defective connec- Reinsert the connector. Also check for conti-
detected 2 times successively. tor cable or poor nuity within the connector cable. If none,
During driving the motor, the
lift overcurrent protective nector. PF lift motor 1 and PF main PWB (YC7)
monitor signal is detected for
500 ms or more 2 times suc- Defective drive Check if the gears rotate smoothly. If not,
cessively. However, the first 1 transmission sys- grease the bushes and gears. Check for
s after PF lift motor 1 is turned tem of motor. broken gears and replace if any.
on is excluded from detection. Defective PF lift Replace the PF lift motor 1.
motor 1.
Defective PF main Replace the PF main PWB (Refer to the ser-
PWB. vice manual for the paper feeder).
(paper feeder) plate elevation smoothly and repair it if any problem is
detected 2 times successively.
During driving the motor, the contact in the con- replace the cable.
motor 2.
1050 SMT lift motor error Defective bottom Check to see if the bottom plate can move
(SMT paper feeder) plate elevation smoothly and repair it if any problem is
SMT lift sensor does not turn cassette.
on within 10 s. Defective connec- Reinsert the connector. Also check for conti-
The lock signal of the motor is
detected continuously for 200 contact in the con- replace the cable.
ms. nector. SMT lift motor and SMT main PWB (YC5)
Defective SMT lift Replace the SMT lift motor.
motor.
Defective SMT Replace the SMT main PWB (Refer to the
main PWB. service manual for the paper feeder).
1-4-31
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
(side paper feeder) plate elevation smoothly and repair it if any problem is
detected 2 times successively. tor cable or poor nuity within the connector cable. If none,
motor 1.
(side paper feeder) plate elevation smoothly and repair it if any problem is
During driving the motor, the contact in the con- replace the cable.
motor 2.
1100 PF lift motor 1 error Defective connec- Reinsert the connector. Also check for conti-
(large capacity feeder) tor cable or poor nuity within the connector cable. If none,
After cassette 3 is inserted, contact in the con- replace the cable.
PF lift sensor 1 does not turn nector. PF lift motor 1 and PF main PWB (YC7)
on within 12 s. This error is Defective drive Check if the gears rotate smoothly. If not,
During driving the motor, the tem of motor. broken gears and replace if any.
lift overcurrent protective
monitor signal is detected for Defective PF lift Replace the PF lift motor 1.
500 ms or more 2 times suc- motor 1.
cessively. However, the first 1 Defective PF main Replace the PF main PWB (Refer to the ser-
s after PF lift motor 1 is turned PWB. vice manual for the paper feeder).
on is excluded from detection.
1-4-32
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
1110 PF lift motor 2 error Defective connec- Reinsert the connector. Also check for conti-
(large capacity feeder) tor cable or poor nuity within the connector cable. If none,
PF lift sensor 2 does not turn nector. PF lift motor 2 and PF main PWB (YC7)
on within 12 s. This error is Defective drive Check if the gears rotate smoothly. If not,
detected 2 times successively. transmission sys- grease the bushes and gears. Check for
lift overcurrent protective
monitor signal is detected for Defective PF lift Replace the PF lift motor 2.
500 ms or more 2 times suc- motor 2.
cessively. However, the first 1 Defective PF main Replace the PF main PWB (Refer to the ser-
s after PF lift motor 2 is turned PWB. vice manual for the paper feeder).
on is excluded from detection.
1140 SF lift motor error Defective connec- Reinsert the connector. Also check for conti-
(Side feeder) tor cable or poor nuity within the connector cable. If none,
SF lift sensor does not turn on nector. SF lift motor and SF main PWB (YC8)
within 30 s. Defective drive Check if the gears rotate smoothly. If not,
The lock signal of the motor is transmission sys- grease the bushes and gears. Check for
detected continuously for 200
ms.
Defective SF lift Replace the SF lift motor.
motor.
Defective SF main Replace the SF main PWB (Refer to the ser-
1800 Paper feeder communica- Improper installa- Follow installation instruction carefully again.
tion error tion paper feeder.
A communication error from
paper feeder is detected 10
times in succession.
nector. PF main PWB (YC13) and engine PWB
(YC19)
1900 Paper feeder EEPROM error Defective PF main Replace the PF main PWB (Refer to the ser-
When writing the data, the PWB. vice manual for the paper feeder).
write data and the read data is
Device damage of Contact the Service Administrative Division.
not continuously in agreement EEPROM.
three times.
1-4-33
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
1950 Transfer belt unit EEPROM Defective connec- Reinsert the connector. Also check for conti-
error tor cable or poor nuity within the connector cable. If none,
No response is issued from contact in the con- replace the cable.
the device in reading/writing nector. Transfer belt unit and engine PWB (YC3)
for 5 ms or more and this Defective transfer Replace the transfer belt unit and check for
problem is repeated 5 times belt unit. correct operation (see 1-5-41).
successively.
Mismatch of reading data from
2 locations occurs 8 times
successively.
Mismatch between writing
data and reading data occurs
8 times successively.
2101 Developer motor K error Defective connec- Reinsert the connector. Also check for conti-
[30 ppm/35 ppm model] tor cable or poor nuity within the connector cable. If none,
After developer motor K is contact in the con- replace the cable.
driven, the ready signal does nector. Developer motor K and motor control PWB
not turn to L within 2 s. (YC7)
After developer motor K is sta- Motor control PWB (YC3) and engine PWB
bilized, the ready signal is at (YC9)
the H level for 1 s continu- Defective drive Check if the gears rotate smoothly. If not,
ously. transmission sys- grease the bushes and gears. Check for
[45 ppm/55 ppm model]
After developer motor K is
driven, the ready signal can- Defective devel- Replace the developer motor K.
not be detected for 5 s. oper motor K.
2102 Developer motor MCY error Defective connec- Reinsert the connector. Also check for conti-
After developer motor MCY is tor cable or poor nuity within the connector cable. If none,
driven, the ready signal can- contact in the con- replace the cable.
not be detected for 5 s. nector. Developer motor MCY and motor control
PWB (YC7)
Motor control PWB (YC3) and engine PWB
(YC9)
Defective devel- Replace the developer motor MCY.
oper motor MCY.
1-4-34
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
2201 Drum motor K steady-state Defective connec- Reinsert the connector. Also check for conti-
After drum motor K is stabi- contact in the con- replace the cable.
lized, the ready signal is at the nector. Drum motor K and motor control PWB (YC5)
H level for 5 s continuously. Motor control PWB (YC3) and engine PWB
(YC9)
Defective drum Replace the drum motor K.
motor K.
2202 Drum motor C steady-state Defective connec- Reinsert the connector. Also check for conti-
After drum motor C is stabi- contact in the con- replace the cable.
lized, the ready signal is at the nector. Drum motor C and motor control PWB (YC4)
(YC9)
Defective drum Replace the drum motor C.
motor C.
2203 Drum motor M steady-state Defective connec- Reinsert the connector. Also check for conti-
After drum motor M is stabi- contact in the con- replace the cable.
lized, the ready signal is at the nector. Drum motor M and motor control PWB
H level for 5 s continuously. (YC5)
(YC9)
Defective drum Replace the drum motor M.
motor M.
1-4-35
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
2204 Drum motor Y steady-state Defective connec- Reinsert the connector. Also check for conti-
After drum motor Y is stabi- contact in the con- replace the cable.
lized, the ready signal is at the nector. Drum motor Y and motor control PWB (YC4)
(YC9)
Defective drum Replace the drum motor Y.
motor Y.
2211 Drum motor K startup error Defective connec- Reinsert the connector. Also check for conti-
Drum motor K is not stabilized tor cable or poor nuity within the connector cable. If none,
within 5 s since the motor is contact in the con- replace the cable.
activated. nector. Drum motor K and motor control PWB (YC5)
(YC9)
Defective drum Replace the drum motor K.
motor K.
2212 Drum motor C startup error Defective connec- Reinsert the connector. Also check for conti-
Drum motor C is not stabilized tor cable or poor nuity within the connector cable. If none,
activated. nector. Drum motor C and motor control PWB (YC4)
(YC9)
Defective drum Replace the drum motor C.
motor C.
1-4-36
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
2213 Drum motor M startup error Defective connec- Reinsert the connector. Also check for conti-
Drum motor M is not stabilized tor cable or poor nuity within the connector cable. If none,
activated. nector. Drum motor M and motor control PWB
(YC5)
(YC9)
Defective drum Replace the drum motor M.
motor M.
2214 Drum motor Y startup error Defective connec- Reinsert the connector. Also check for conti-
Drum motor Y is not stabilized tor cable or poor nuity within the connector cable. If none,
activated. nector. Drum motor Y and motor control PWB (YC4)
(YC9)
Defective drum Replace the drum motor Y.
motor Y.
2300 Fuser motor error Defective connec- Reinsert the connector. Also check for conti-
After fuser motor is driven, the tor cable or poor nuity within the connector cable. If none,
ready signal does not turn to L contact in the con- replace the cable.
within 2 s. nector. Fuser motor and feed PWB 1 (YC18)
After fuser motor is stabilized, Feed PWB 1 (YC1) and engine PWB (YC6)
the ready signal is at the H Defective drive Check if the gears rotate smoothly. If not,
level for 1 s continuously.
Defective fuser Replace the fuser motor.
motor.
1-4-37
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
2550 Paper feed motor error Defective connec- Reinsert the connector. Also check for conti-
After paper feed motor is tor cable or poor nuity within the connector cable. If none,
driven, the ready signal does contact in the con- replace the cable.
not turn to L within 2 s. nector. Paper feed motor and feed PWB 2 (YC2)
After paper feed motor is sta- Feed PWB 2 (YC1) and engine PWB (YC4)
bilized, the ready signal is at Defective drive Check if the gears rotate smoothly. If not,
the H level for 1 s continu-
ously. tem of motor. broken gears and replace if any.
Defective paper Replace the paper feed motor.
feed motor.
2600 PF paper feed motor error Defective connec- Reinsert the connector. Also check for conti-
(paper feeder) tor cable or poor nuity within the connector cable. If none,
After PF paper feed motor is contact in the con- replace the cable.
driven, the ready signal does nector. PF paper feed motor and PF main PWB
Defective PF paper Replace the PF paper feed motor.
feed motor.
2610 PF paper feed motor error Defective connec- Reinsert the connector. Also check for conti-
(side paper feeder) tor cable or poor nuity within the connector cable. If none,
After PF paper feed motor is contact in the con- replace the cable.
driven, the ready signal does nector. PF paper feed motor and PF main PWB
Defective PF paper Replace the PF paper feed motor.
feed motor.
1-4-38
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
2640 SF paper feed motor error Defective connec- Reinsert the connector. Also check for conti-
(side feeder) tor cable or poor nuity within the connector cable. If none,
After SF paper feed motor is contact in the con- replace the cable.
driven, the ready signal does nector. SF paper feed motor and SF main PWB
Defective SF paper Replace the SF paper feed motor.
feed motor.
Defective SF main Replace the SF main PWB (Refer to the ser-
2650 SMT paper feed motor error Defective connec- Reinsert the connector. Also check for conti-
(SMT paper feeder) tor cable or poor nuity within the connector cable. If none,
After SMT paper feed motor is contact in the con- replace the cable.
driven, the ready signal does nector. SMT paper feed motor and SMT main PWB
After SMT paper feed motor is Defective drive Check if the gears rotate smoothly. If not,
stabilized, the ready signal is transmission sys- grease the bushes and gears. Check for
at the H level for 1 s continu-
ously.
Defective SMT Replace the SMT paper feed motor.
paper feed motor.
Defective SMT Replace the SMT main PWB (Refer to the
main PWB. service manual for the paper feeder).
2700 Color release motor error Defective connec- Reinsert the connector. Also check for conti-
When the color release motor tor cable or poor nuity within the connector cable. If none,
is driven, the color release contact in the con- replace the cable.
sensor does not turn on/off for nector. Color release motor and engine PWB (YC3)
1 s. Defective drive Check if the gears rotate smoothly. If not,
Defective color Replace the color release motor.
release motor.
1-4-39
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
2730 Transfer release motor error Defective connec- Reinsert the connector. Also check for conti-
When the transfer release tor cable or poor nuity within the connector cable. If none,
motor is driven, the transfer contact in the con- replace the cable.
release sensor does not turn nector. Transfer release motor and relay PWB
on/off for 1 s. (YC14)
Relay PWB (YC14) and feed PWB 1 (YC14)
Defective transfer Replace the transfer release motor.
release motor.
2760 Transfer motor startup error Defective connec- Reinsert the connector. Also check for conti-
Transfer motor is not stabi- tor cable or poor nuity within the connector cable. If none,
lized within 5 s since the contact in the con- replace the cable.
motor is activated. nector. Transfer motor and feed PWB 1 (YC13)
Defective transfer Replace the transfer motor.
motor.
2770 Transfer skew error Defective connec- Reinsert the connector. Also check for conti-
An abnormal value is detected tor cable or poor nuity within the connector cable. If none,
to transfer skew sensor. contact in the con- replace the cable.
nector. Transfer belt unit and engine PWB (YC3)
Defective transfer Replace the transfer skew sensor.
skew sensor.
2780 Transfer skew sensor error Defective connec- Reinsert the connector. Also check for conti-
to transfer skew sensor. contact in the con- replace the cable.
nector. Transfer belt unit and engine PWB (YC3)
Defective transfer Replace the transfer skew sensor.
skew sensor.
1-4-40
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
2790 Transfer skew motor error Defective connec- Reinsert the connector. Also check for conti-
When the transfer skew motor tor cable or poor nuity within the connector cable. If none,
is driven, timeouts were contact in the con- replace the cable.
detected twice in a row. nector. Transfer skew motor and engine PWB (YC3)
Defective transfer Replace the transfer skew motor.
skew motor.
2820 Transfer motor steady-state Defective connec- Reinsert the connector. Also check for conti-
After transfer motor is stabi- contact in the con- replace the cable.
lized, the ready signal is at the nector. Transfer motor and feed PWB 1 (YC13)
H level for 5 s continuously. Feed PWB 1 (YC2) and engine PWB (YC5)
Defective transfer Replace the transfer motor.
motor.
2840 Transfer cleaning motor Defective connec- Reinsert the connector. Also check for conti-
After transfer cleaning motor contact in the con- replace the cable.
is driven, the ready signal nector. Transfer cleaning motor and engine PWB
does not turn to L within 2 s. (YC3)
After transfer cleaning motor Defective drive Check if the gears rotate smoothly. If not,
is stabilized, the ready signal transmission sys- grease the bushes and gears. Check for
is at the H level for 1 s contin-
uously.
Defective transfer Replace the transfer cleaning motor.
cleaning motor.
2850 Transfer belt sensor error Defective connec- Reinsert the connector. Also check for conti-
The signal is not received for tor cable or poor nuity within the connector cable. If none,
100 ms in succession. contact in the con- replace the cable.
nector. Transfer belt sensor and engine PWB (YC3)
Defective transfer Replace the transfer belt sensor.
belt sensor.
1-4-41
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
2860 Transfer belt sensor error Defective connec- Reinsert the connector. Also check for conti-
The signal is not received for tor cable or poor nuity within the connector cable. If none,
100 ms in succession. contact in the con- replace the cable.
nector. Transfer belt sensor and engine PWB (YC3)
Defective transfer Replace the transfer belt sensor.
belt sensor.
2950 Motor control PWB commu- Defective connec- Reinsert the connector. Also check for conti-
nication error tor cable or poor nuity within the connector cable. If none,
A communication error from contact in the con- replace the cable.
the motor control PWB is nector. Motor control PWB (YC3) and engine PWB
detected 10 times in succes- (YC9)
sion. Defective motor Replace the motor control PWB and check
control PWB. for correct operation.
3100 Scanner carriage error Defective connec- Reinsert the connector. Also check for conti-
The home position is not cor- tor cable or poor nuity within the connector cable. If none,
rect when the power is turned contact in the con- replace the cable.
on or at the start of copying nector. Home position sensor and ISC PWB (YC8)
using the table. Scanner motor and ISC PWB (YC5)
ISC PWB (YC3) and main PWB (YC11)
Defective home Replace the home position sensor.
position sensor.
Defective scanner Replace the scanner motor.
motor.
Defective ISC Replace the ISC PWB and check for correct
PWB. operation.
3200 Exposure lamp error Defective connec- Reinsert the connector. Also check for conti-
When input value at the time tor cable or poor nuity within the connector cable. If none,
of LED PWB illumination does contact in the con- replace the cable.
not exceed the threshold nector. LED PWB and ISC PWB (YC6)
value between 5 s. ISC PWB (YC3) and main PWB (YC11)
Defective LED Replace the LED PWB and check for correct
PWB. operation.
PWB. operation.
1-4-42
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
3210 CIS lamp error Defective connec- Reinsert the connector. Also check for conti-
When input value at the time tor cable or poor nuity within the connector cable. If none,
of CIS illumination does not contact in the con- replace the cable.
exceed the threshold value nector. DP main PWB (YC1) and ISC PWB (YC12)
between 5 s. ISC PWB (YC3) and main PWB (YC11)
Defective CIS. Replace the CIS and check for correct oper-
ation.
Defective DP main Replace the DP main PWB and check for
PWB. correct operation.
Defective DP relay Replace the DP relay PWB and check for
3300 Optical system (AGC) error Defective connec- Reinsert the connector. Also check for conti-
After AGC, correct input is not tor cable or poor nuity within the connector cable. If none,
obtained at CCD. contact in the con- replace the cable.
nector. CCD PWB (YC2) and ISC PWB (YC9)
Defective exposure Replace the LED PWB and check for correct
lamp. operation.
Defective CCD Replace the CCD PWB and check for cor-
PWB. rect operation.
PWB. operation.
3310 CIS AGC error Defective CIS. Replace the CIS and check for correct oper-
After AGC, correct input is not ation.
obtained at CIS. Defective DP main Replace the DP main PWB and check for
Defective DP relay Replace the DP relay PWB and check for
3500 Communication error Defective connec- Reinsert the connector. Also check for conti-
between scanner and ASIC tor cable or poor nuity within the connector cable. If none,
An error code is detected. contact in the con- replace the cable.
nector. ISC PWB (YC3) and main PWB (YC11)
PWB. operation.
3600 Scanner sequence error Defective ISC Replace the ISC PWB and check for correct
PWB. operation.
3700 Scanner device error CCD connector Reinsert the image scanner unit connector if
inserted incor- necessary.
rectly.
1-4-43
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
3900 Backup memory read/write Defective backup Replace the ISC PWB and check for correct
error (ISC PWB) memory or PWB. operation.
Read and write data does not
match.
3910 Backup memory data error Defective backup Replace the ISC PWB and check for correct
(ISC PWB) memory or PWB. operation.
Data in the specified area of
the backup memory does not
match the specified values.
4001 Polygon motor K synchroni- Defective connec- Reinsert the connector. Also check for conti-
zation error tor cable or poor nuity within the connector cable. If none,
After polygon motor K is contact in the con- replace the cable.
driven, the ready signal does nector. Polygon motor K and LSU relay PWB (YC4)
not turn to L within 30 s. LSU relay PWB (YC4) and engine PWB
(YC12)
Defective polygon Replace the laser scanner unit (see page 1-
motor K. 5-25).
4002 Polygon motor C synchroni- Defective connec- Reinsert the connector. Also check for conti-
After polygon motor C is contact in the con- replace the cable.
driven, the ready signal does nector. Polygon motor C and LSU relay PWB (YC9)
(YC12)
motor C. 5-25).
4003 Polygon motor M synchro- Defective connec- Reinsert the connector. Also check for conti-
nization error tor cable or poor nuity within the connector cable. If none,
After polygon motor M is contact in the con- replace the cable.
driven, the ready signal does nector. Polygon motor M and LSU relay PWB (YC7)
(YC12)
motor M. 5-25).
1-4-44
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
4004 Polygon motor Y synchroni- Defective connec- Reinsert the connector. Also check for conti-
After polygon motor Y is contact in the con- replace the cable.
driven, the ready signal does nector. Polygon motor Y and LSU relay PWB
LSU relay PWB (YC3) and engine PWB
(YC12)
motor Y. 5-25).
4011 Polygon motor K steady- Defective connec- Reinsert the connector. Also check for conti-
state error tor cable or poor nuity within the connector cable. If none,
After polygon motor K is stabi- contact in the con- replace the cable.
lized, the ready signal is at the nector. Polygon motor K and LSU relay PWB (YC4)
H level for 15 s continuously. LSU relay PWB (YC4) and engine PWB
(YC12)
motor K. 5-25).
4012 Polygon motor C steady- Defective connec- Reinsert the connector. Also check for conti-
After polygon motor C is stabi- contact in the con- replace the cable.
lized, the ready signal is at the nector. Polygon motor C and LSU relay PWB (YC9)
H level for 15 s continuously. LSU relay PWB (YC3) and engine PWB
(YC12)
motor C. 5-25).
4013 Polygon motor M steady- Defective connec- Reinsert the connector. Also check for conti-
After polygon motor M is sta- contact in the con- replace the cable.
bilized, the ready signal is at nector. Polygon motor M and LSU relay PWB (YC7)
the H level for 15 s continu- LSU relay PWB (YC3) and engine PWB
ously. (YC12)
motor M. 5-25).
1-4-45
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
4014 Polygon motor Y steady- Defective connec- Reinsert the connector. Also check for conti-
After polygon motor Y is stabi- contact in the con- replace the cable.
lized, the ready signal is at the nector. Polygon motor Y and LSU relay PWB
H level for 15 s continuously. (YC11)
(YC12)
motor Y. 5-25).
4101 BD initialization error K Defective connec- Reinsert the connector. Also check for conti-
After polygon motor K is tor cable or poor nuity within the connector cable. If none,
driven, ASIC detects a BD contact in the con- replace the cable.
error for 1 s. nector. Laser scanner unit and LSU relay PWB
(YC5)
(YC12)
Defective PD PWB Replace the laser scanner unit (see page 1-
K. 5-25).
4102 BD initialization error C Defective connec- Reinsert the connector. Also check for conti-
After polygon motor C is tor cable or poor nuity within the connector cable. If none,
(YC10)
(YC12)
C. 5-25).
4103 BD initialization error M Defective connec- Reinsert the connector. Also check for conti-
After polygon motor M is tor cable or poor nuity within the connector cable. If none,
(YC8)
(YC12)
M. 5-25).
1-4-46
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
4104 BD initialization error Y Defective connec- Reinsert the connector. Also check for conti-
After polygon motor Y is tor cable or poor nuity within the connector cable. If none,
(YC12)
(YC12)
Y. 5-25).
4201 BD steady-state error K Defective connec- Reinsert the connector. Also check for conti-
The BD signal is not detected. tor cable or poor nuity within the connector cable. If none,
nector. Laser scanner unit and LSU relay PWB
(YC5)
(YC12)
K. 5-25).
4202 BD steady-state error C Defective connec- Reinsert the connector. Also check for conti-
(YC10)
(YC12)
C. 5-25).
4203 BD steady-state error M Defective connec- Reinsert the connector. Also check for conti-
(YC8)
(YC12)
M. 5-25).
1-4-47
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
4204 BD steady-state error Y Defective connec- Reinsert the connector. Also check for conti-
(YC12)
(YC12)
Y. 5-25).
4300 Polygon motor phase error Defective laser Replace the laser scanner unit (see page 1-
ASIC won’t settle in comple- scanner unit. 5-25).
tion of phase adjustment for 2 Defective engine Replace the engine PWB and check for cor-
seconds after a BD signal is PWB. rect operation (see page 1-5-54).
detected.
4401 LD over-current detection Defective connec- Reinsert the connector. Also check for conti-
error K tor cable or poor nuity within the connector cable. If none,
An over current signal has contact in the con- replace the cable.
been detected for 15 ms in nector. Laser scanner unit and LSU relay PWB
succession when LD is illumi- (YC5)
nated. LSU relay PWB (YC3) and engine PWB
(YC12)
Defective APC Replace the laser scanner unit (see page 1-
PWB K. 5-25).
error C tor cable or poor nuity within the connector cable. If none,
(YC12)
PWB C. 5-25).
1-4-48
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
error M tor cable or poor nuity within the connector cable. If none,
(YC12)
PWB M. 5-25).
error Y tor cable or poor nuity within the connector cable. If none,
(YC12)
PWB Y. 5-25).
4600 LSU cleaning motor error Defective connec- Reinsert the connector. Also check for conti-
After LSU cleaning motor is tor cable or poor nuity within the connector cable. If none,
driven, the ready signal does contact in the con- replace the cable.
not turn to L within 2 s. nector. LSU cleaning motor and engine PWB
After LSU cleaning motor is (YC21)
stabilized, the ready signal is Defective drive Check if the gears rotate smoothly. If not,
at the H level for 1 s continu-
ously. tem of motor. broken gears and replace if any.
Defective LSU Replace the LSU cleaning motor.
cleaning motor.
5101 Main high-voltage error K Defective connec- Reinsert the connector. Also check for conti-
Abnormality of charger roller tor cable or poor nuity within the connector cable. If none,
K is detected when Vpp contact in the con- replace the cable.
adjustment. nector. High voltage PWB 1 (YC4) and engine PWB
(YC17)
Defective high volt- Replace the high voltage PWB 1 and check
age PWB 1. for correct operation (see page 1-5-59).
1-4-49
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
5102 Main high-voltage error C Defective connec- Reinsert the connector. Also check for conti-
C is detected when Vpp contact in the con- replace the cable.
(YC16)
5103 Main high-voltage error M Defective connec- Reinsert the connector. Also check for conti-
M is detected when Vpp contact in the con- replace the cable.
(YC17)
5104 Main high-voltage error Y Defective connec- Reinsert the connector. Also check for conti-
Y is detected when Vpp contact in the con- replace the cable.
(YC16)
6000 Broken fuser heater wire Defective connec- Reinsert the connector. Also check for conti-
Fuser thermistor 1 does not tor cable or poor nuity within the connector cable. If none,
reach 100° C/212 °F even contact in the con- replace the cable.
after 60 s during warming up. nector. Power source PWB (YC3) and fuser IH
The detected temperature of PWB (YC1)
fuser thermistor 1 does not Fuser IH PWB (YC4) and engine PWB
reach the specified tempera- (YC26)
ture (ready indication temper-
Deformed connec- See page 1-4-55.
ature) for 60 s in warming up tor pin.
after reached to 100° C/212
°F. Defective triac. See page 1-4-55.
Fuser thermostat Replace the fuser unit (see page 1-5-45).
triggered.
Defective fuser IH. Replace the fuser unit (see page 1-5-45).
1-4-50
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
6020 Abnormally high fuser Deformed connec- See page 1-4-55.
thermistor 1 temperature tor pin.
Fuser thermistor 1 detects a
Defective triac. See page 1-4-55.
temperature higher than
240°C/464°F for 1 s. Shorted fuser Replace the fuser unit (see page 1-5-45).
thermistor 1.
6030 Broken fuser thermistor 1 Defective connec- Reinsert the connector. Also check for conti-
wire tor cable or poor nuity within the connector cable. If none,
Input from fuser thermistor 1 contact in the con- replace the cable.
is 984 or more (A/D value) nector. Fuser unit and engine PWB (YC26)
continuously for 1 s. Deformed connec- See page 1-4-55.
tor pin.
Broken fuser Replace the fuser unit (see page 1-5-45).
thermistor 1 wire.
triggered.
6040 Fuser heater error Defective connec- Reinsert the connector. Also check for conti-
Input from fuser thermistor 2 tor cable or poor nuity within the connector cable. If none,
is abnormal value continu- contact in the con- replace the cable.
ously for 1 s. nector. Fuser unit and engine PWB (YC26)
tor pin.
thermistor 2 wire.
1-4-51
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
6050 Abnormally low fuser Deformed connec- See page 1-4-55.
temperature lower than
100°C/212°F for 1 s after Defective fuser Replace the fuser unit (see page 1-5-45).
warming up. thermistor 1.
thermistor 4.
tor pin.
thermistor 4 wire.
Fuser thermistor 4 detects a Defective triac. See page 1-4-55.
temperature lower than 30°C/
86°F for 1 s after warming up. Defective fuser Replace the fuser unit (see page 1-5-45).
thermistor 1.
1-4-52
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
6200 Broken fuser edge heater Defective connec- Reinsert the connector. Also check for conti-
Fuser thermistor 2 does not contact in the con- replace the cable.
reach 100° C/212 °F even nector. Power source PWB (YC3) and fuser IH
after 60 s during warming up. PWB (YC1)
The detected temperature of Fuser IH PWB (YC4) and engine PWB
fuser thermistor 2 does not (YC26)
reach the specified tempera- Deformed connec- See page 1-4-55.
ture (ready indication temper- tor pin.
ature) for 60 s in warming up
after reached to 100° C/212 Defective triac. See page 1-4-55.
°F. Fuser thermostat Replace the fuser unit (see page 1-5-45).
triggered.
Fuser thermistor 2 detects a Defective triac. See page 1-4-55.
thermistor 2.
continuously for 1 s.
tor pin.
thermistor 2 wire.
triggered.
1-4-53
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
temperature lower than 50°C/
122°F for 1 s after warming Defective fuser Replace the fuser unit (see page 1-5-45).
up. thermistor 2.
thermistor 3.
tor pin.
thermistor 3 wire.
triggered.
1-4-54
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
6000 Broken fuser heater wire Deformed connec- If the I/F connector pins of the fuser unit and
6020 Abnormally high fuser tor pin. the main unit are deformed owing to foreign
thermistor 1 temperature matters, such as paper dusts, replace the
6030 Broken fuser thermistor 1 connectors or the units including the con-
wire nectors.
6040 Fuser heater error Defective triac. Remove the power cord and check that the
6050 Abnormally low fuser resistance between terminals T1 and T2 of
thermistor 1 temperature the triac TRA51 is of several Mega-Ohms
6120 Abnormally high fuser and not shorted (see figure 1-4-4). If failed,
thermistor 4 temperature
replace the power source PWB (see page 1-
6130 Broken fuser thermistor 4 5-56).
wire
6150 Abnormally low fuser
6200 Broken fuser edge heater
wire
6220 Abnormally high fuser
6230 Broken fuser thermistor 2
wire T1
6250 Abnormally low fuser T2
6320 Abnormally high fuser
thermistor 3 temperature TRA51
6330 Broken fuser thermistor 3
wire
Com- Power source PWB
bined Figure 1-4-4
6610 Fuser release motor error Defective connec- Reinsert the connector. Also check for conti-
When the fuser release motor tor cable or poor nuity within the connector cable. If none,
is driven, the fuser release contact in the con- replace the cable.
sensor does not turn on/off for nector. Fuser unit and engine PWB (YC26)
5 s.
Defective fuser Replace the fuser release motor.
release motor.
1-4-55
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
6710 Fuser IH PWB CPU reset Defective connec- Reinsert the connector. Also check for conti-
Watch doc timer has been contact in the con- replace the cable.
overflowed. nector. Fuser IH PWB (YC4) and engine PWB
(YC26)
Defective fuser IH Replace the fuser IH PWB and check for
6720 Fuser IH belt rotation error Defective connec- Reinsert the connector. Also check for conti-
A belt rotating pulse is not tor cable or poor nuity within the connector cable. If none,
received for 1 second. contact in the con- replace the cable.
nector. Fuser unit and engine PWB (YC26)
Defective fuser belt Replace the fuser belt sensor.
sensor.
6730 Abnormally high fuser IH Defective connec- Reinsert the connector. Also check for conti-
PWB temperature 1 tor cable or poor nuity within the connector cable. If none,
The input detect temperature contact in the con- replace the cable.
is greater than 105°C/221 °F. nector. Fuser IH PWB (YC4) and engine PWB
(YC26)
6740 Abnormally high fuser IH Defective connec- Reinsert the connector. Also check for conti-
PWB temperature 2 tor cable or poor nuity within the connector cable. If none,
The input detect temperature contact in the con- replace the cable.
is greater than 105°C/221 °F. nector. Fuser IH PWB (YC4) and engine PWB
(YC26)
6750 Fuser IH output over-cur- Defective connec- Reinsert the connector. Also check for conti-
rent error tor cable or poor nuity within the connector cable. If none,
The output current is greater contact in the con- replace the cable.
than 75A for 10 ms in succes- nector. Fuser IH PWB (YC4) and engine PWB
sion. (YC26)
1-4-56
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
6760 Fuser IH input over-current Defective connec- Reinsert the connector. Also check for conti-
The input current is greater contact in the con- replace the cable.
than 20A for 10 ms in succes- nector. Fuser IH PWB (YC4) and engine PWB
sion. (YC26)
6770 Fuser IH low electric power Defective connec- Reinsert the connector. Also check for conti-
The preset power is less than contact in the con- replace the cable.
0.6 times of it for 120 ms in nector. Fuser IH PWB (YC4) and engine PWB
succession. (YC26)
6780 Fuser IH input over-voltage Defective connec- Reinsert the connector. Also check for conti-
The input voltage is greater contact in the con- replace the cable.
than 140V for 200 ms in suc- nector. Fuser IH PWB (YC4) and engine PWB
cession. (YC26)
6900 Fuser front fan motor error Defective connec- Reinsert the connector. Also check for conti-
When the fuser front fan tor cable or poor nuity within the connector cable. If none,
motor is driven, alarm signal is contact in the con- replace the cable.
detected for 5 s continuously. nector. Fuser front fan motor and engine PWB
(YC26)
Defective fuser Replace the fuser front fan motor.
front fan motor.
6910 Fuser rear fan motor error Defective connec- Reinsert the connector. Also check for conti-
When the fuser rear fan motor tor cable or poor nuity within the connector cable. If none,
is driven, alarm signal is contact in the con- replace the cable.
detected for 5 s continuously. nector. Fuser rear fan motor and engine PWB
(YC26)
Defective fuser Replace the fuser rear fan motor.
rear fan motor.
1-4-57
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
6920 Coil fan motor 1 error Defective connec- Reinsert the connector. Also check for conti-
When the coil fan motor 1 is tor cable or poor nuity within the connector cable. If none,
driven, alarm signal is contact in the con- replace the cable.
detected for 5 s continuously. nector. Coil fan motor 1 and front PWB (YC4)
Front PWB (YC3) and engine PWB (YC7)
Defective coil fan Replace coil fan motor 1.
motor 1.
6930 Coil fan motor 2 error Defective connec- Reinsert the connector. Also check for conti-
When the coil fan motor 2 is tor cable or poor nuity within the connector cable. If none,
driven, alarm signal is contact in the con- replace the cable.
detected for 5 s continuously. nector. Coil fan motor 2 and engine PWB (YC26)
Defective coil fan Replace coil fan motor 2.
motor 2.
6940 IH fan motor error Defective connec- Reinsert the connector. Also check for conti-
When the IH fan motor is tor cable or poor nuity within the connector cable. If none,
driven, the alarm signal is contact in the con- replace the cable.
detected for 5 s continuously. nector. IH fan motor and feed PWB 1 (YC11)
Defective IH fan Replace the IH fan motor.
motor.
6950 Fuser IH PWB communica- Defective connec- Reinsert the connector. Also check for conti-
tion error tor cable or poor nuity within the connector cable. If none,
No response is received in 30 contact in the con- replace the cable.
ms since a command is sent nector. Fuser IH PWB (YC4) and engine PWB
to IHCPU. (YC26)
A checksum error is detected
10 times in succession. PWB. correct operation.
6990 Fuser power supply incom- Defective fuser IH Replace the fuser IH PWB and check for
patibility PWB. correct operation.
Information won’t match
between the engine backup PWB. rect operation (see page 1-5-54).
and the fuser IH PWB.
1-4-58
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
7001 Toner motor K error Defective connec- Reinsert the connector. Also check for conti-
When the toner motor K is tor cable or poor nuity within the connector cable. If none,
driven, the pulse of screw contact in the con- replace the cable.
sensor K is not detected. nector. Toner motor K and engine PWB (YC27)
Defective screw Replace the screw sensor K.
sensor K.
Defective toner Replace the toner motor K.
motor K.
7002 Toner motor C error Defective connec- Reinsert the connector. Also check for conti-
When the toner motor C is tor cable or poor nuity within the connector cable. If none,
sensor C is not detected. nector. Toner motor C and engine PWB (YC27)
Defective screw Replace the screw sensor C.
sensor C.
Defective toner Replace the toner motor C.
motor C.
7003 Toner motor M error Defective connec- Reinsert the connector. Also check for conti-
When the toner motor M is tor cable or poor nuity within the connector cable. If none,
sensor M is not detected. nector. Toner motor M and engine PWB (YC27)
Defective screw Replace the screw sensor M.
sensor M.
Defective toner Replace the toner motor M.
motor M.
7004 Toner motor Y error Defective connec- Reinsert the connector. Also check for conti-
When the toner motor Y is tor cable or poor nuity within the connector cable. If none,
sensor Y is not detected. nector. Toner motor Y and engine PWB (YC27)
Defective screw Replace the screw sensor Y.
sensor Y.
Defective toner Replace the toner motor Y.
motor Y.
1-4-59
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
7101 Toner sensor K error Defective connec- Reinsert the connector. Also check for conti-
Sensor output value of 60 or tor cable or poor nuity within the connector cable. If none,
less or 944 or more continued contact in the con- replace the cable.
for 3 s. nector. Toner sensor K and front PWB (YC7)
7102 Toner sensor C error Defective connec- Reinsert the connector. Also check for conti-
for 3 s. nector. Toner sensor C and front PWB (YC13)
7103 Toner sensor M error Defective connec- Reinsert the connector. Also check for conti-
for 3 s. nector. Toner sensor M and front PWB (YC11)
7104 Toner sensor Y error Defective connec- Reinsert the connector. Also check for conti-
for 3 s. nector. Toner sensor Y and front PWB (YC15)
7200 Broken outer temperature Defective connec- Reinsert the connector. Also check for conti-
sensor 2 wire tor cable or poor nuity within the connector cable. If none,
The sensor input sampling is contact in the con- replace the cable.
greater than 230. nector. Outer temperature sensor 2 and front PWB
(YC19)
Defective outer Replace outer temperature sensor 2.
temperature sen-
sor 2.
1-4-60
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
7210 Short-circuited outer tem- Defective connec- Reinsert the connector. Also check for conti-
perature sensor 2 tor cable or poor nuity within the connector cable. If none,
less than 69. nector. Outer temperature sensor 2 and front PWB
(YC19)
temperature sen-
sor 2.
7221 Broken LSU thermistor K Defective connec- Reinsert the connector. Also check for conti-
greater than 255. nector. Laser scanner unit and LSU relay PWB
(YC5)
(YC12)
Defective LSU Replace the laser scanner unit (see page 1-
thermistor K. 5-25).
7222 Broken LSU thermistor C Defective connec- Reinsert the connector. Also check for conti-
(YC10)
(YC12)
thermistor C. 5-25).
7223 Broken LSU thermistor M Defective connec- Reinsert the connector. Also check for conti-
(YC8)
(YC12)
thermistor M. 5-25).
1-4-61
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
7224 Broken LSU thermistor Y Defective connec- Reinsert the connector. Also check for conti-
(YC12)
(YC12)
thermistor Y. 5-25).
7231 Short-circuited LSU therm- Defective connec- Reinsert the connector. Also check for conti-
istor K tor cable or poor nuity within the connector cable. If none,
less than 0. nector. Laser scanner unit and LSU relay PWB
(YC5)
(YC12)
thermistor K. 5-25).
istor C tor cable or poor nuity within the connector cable. If none,
(YC10)
(YC12)
thermistor C. 5-25).
istor M tor cable or poor nuity within the connector cable. If none,
(YC8)
(YC12)
thermistor M. 5-25).
1-4-62
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
istor Y tor cable or poor nuity within the connector cable. If none,
(YC12)
(YC12)
thermistor Y. 5-25).
7241 Broken developer thermis- Defective connec- Reinsert the connector. Also check for conti-
tor K wire tor cable or poor nuity within the connector cable. If none,
greater than 255. nector. Developer unit K and front PWB (YC9)
Defective devel- Replace developer unit K (see page 1-5-36).
oper thermistor K.
tor C wire tor cable or poor nuity within the connector cable. If none,
greater than 255. nector. Developer unit C and front PWB (YC13)
Defective devel- Replace developer unit C (see page 1-5-36).
oper thermistor C.
tor M wire tor cable or poor nuity within the connector cable. If none,
greater than 255. nector. Developer unit M and front PWB (YC11)
Defective devel- Replace developer unit M (see page 1-5-
oper thermistor M. 36).
1-4-63
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
tor Y wire tor cable or poor nuity within the connector cable. If none,
greater than 255. nector. Developer unit Y and front PWB (YC15)
Defective devel- Replace developer unit Y (see page 1-5-36).
oper thermistor Y.
7251 Short-circuited developer Defective connec- Reinsert the connector. Also check for conti-
thermistor K tor cable or poor nuity within the connector cable. If none,
less than 0. nector. Developer unit K and front PWB (YC9)
Defective devel- Replace developer unit K (see page 1-5-36).
oper thermistor K.
thermistor C tor cable or poor nuity within the connector cable. If none,
less than 0. nector. Developer unit C and front PWB (YC13)
Defective devel- Replace developer unit C (see page 1-5-36).
oper thermistor C.
thermistor M tor cable or poor nuity within the connector cable. If none,
less than 0. nector. Developer unit M and front PWB (YC11)
Defective devel- Replace developer unit M (see page 1-5-
oper thermistor M. 36).
thermistor Y wire tor cable or poor nuity within the connector cable. If none,
less than 0. nector. Developer unit Y and front PWB (YC15)
Defective devel- Replace developer unit Y (see page 1-5-36).
oper thermistor Y.
1-4-64
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
7401 Developer unit K type mis- Defective connec- Reinsert the connector. Also check for conti-
match error tor cable or poor nuity within the connector cable. If none,
Absence of the developer unit contact in the con- replace the cable.
K is detected. nector. Developer unit K and front PWB (YC9)
Different type of Install the correct developer unit.
the developer unit
is installed.
7402 Developer unit C type mis- Defective connec- Reinsert the connector. Also check for conti-
C is detected. nector. Developer unit C and front PWB (YC13)
the developer unit
is installed.
7403 Developer unit M type mis- Defective connec- Reinsert the connector. Also check for conti-
M is detected. nector. Developer unit M and front PWB (YC11)
the developer unit
is installed.
7404 Developer unit Y type mis- Defective connec- Reinsert the connector. Also check for conti-
Y is detected. nector. Developer unit Y and front PWB (YC15)
the developer unit
is installed.
7601 ID sensor 1 error Defective connec- Reinsert the connector. Also check for conti-
in the input data to ID sensor contact in the con- replace the cable.
1. nector. ID sensor 1 and feed PWB 1 (YC10)
7602 ID sensor 2 error Defective connec- Reinsert the connector. Also check for conti-
in the input data to ID sensor contact in the con- replace the cable.
2. nector. ID sensor 2 and feed PWB 1 (YC10)
1-4-65
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
7800 Broken outer temperature Defective connec- Reinsert the connector. Also check for conti-
sensor 1 wire tor cable or poor nuity within the connector cable. If none,
greater than 255. nector. Outer temperature sensor 1 and front PWB
(YC16)
temperature sen-
sor 1.
7810 Short-circuited outer tem- Defective connec- Reinsert the connector. Also check for conti-
perature sensor 1 tor cable or poor nuity within the connector cable. If none,
less than 0. nector. Outer temperature sensor 1 and front PWB
(YC16)
temperature sen-
sor 1.
7901 Drum K EEPROM error Defective connec- Reinsert the connector. Also check for conti-
No response is issued from tor cable or poor nuity within the connector cable. If none,
the device in reading/writing contact in the con- replace the cable.
for 5 ms or more and this nector. Drum PWB K and front PWB (YC7)
problem is repeated five times Front PWB (YC2) and engine PWB (YC10)
successively. Defective drum Replace the drum unit K (see page 1-5-36).
PWB K.
two locations occurs 8 times
successively.
7902 Drum C EEPROM error Defective connec- Reinsert the connector. Also check for conti-
for 5 ms or more and this nector. Drum PWB C and front PWB (YC12)
successively. Defective drum Replace the drum unit C (see page 1-5-36).
Mismatch of reading data from PWB C.
successively.
1-4-66
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
7903 Drum M EEPROM error Defective connec- Reinsert the connector. Also check for conti-
for 5 ms or more and this nector. Drum PWB M and front PWB (YC10)
successively. Defective drum Replace the drum unit M (see page 1-5-36).
PWB M.
successively.
7904 Drum Y EEPROM error Defective connec- Reinsert the connector. Also check for conti-
for 5 ms or more and this nector. Drum PWB Y and front PWB (YC14)
successively. Defective drum Replace the drum unit Y (see page 1-5-36).
Mismatch of reading data from PWB Y.
successively.
7911 Developer unit K EEPROM Defective connec- Reinsert the connector. Also check for conti-
the device in reading/writing nector. Developer unit K and front PWB (YC9)
for 5 ms or more and this Front PWB (YC2) and engine PWB (YC10)
problem is repeated five times Defective devel- Replace the developer unit K (see page 1-5-
successively.
oper unit K. 36).
successively.
1-4-67
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
7912 Developer unit C EEPROM Defective connec- Reinsert the connector. Also check for conti-
the device in reading/writing nector. Developer unit C and front PWB (YC13)
problem is repeated five times Defective devel- Replace the developer unit C (see page 1-5-
successively.
oper unit C. 36).
successively.
7913 Developer unit M EEPROM Defective connec- Reinsert the connector. Also check for conti-
the device in reading/writing nector. Developer unit M and front PWB (YC11)
problem is repeated five times Defective devel- Replace the developer unit M (see page 1-5-
successively.
oper unit M. 36).
successively.
7914 Developer unit Y EEPROM Defective connec- Reinsert the connector. Also check for conti-
the device in reading/writing nector. Developer unit Y and front PWB (YC15)
problem is repeated five times Defective devel- Replace the developer unit Y (see page 1-5-
successively. oper unit Y. 36).
successively.
1-4-68
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
7941 Laser scanner unit K Defective connec- Reinsert the connector. Also check for conti-
EEPROM error tor cable or poor nuity within the connector cable. If none,
Mismatch of reading data from contact in the con- replace the cable.
two locations occurs 8 times nector. APC PWB K and LSU relay PWB (YC5)
successively. LSU relay PWB (YC2) and engine PWB
Mismatch between writing (YC11)
8 times successively. PWB K. 5-25).
7942 Laser scanner unit C Defective connec- Reinsert the connector. Also check for conti-
two locations occurs 8 times nector. APC PWB C and LSU relay PWB (YC10)
8 times successively. PWB C. 5-25).
7943 Laser scanner unit M Defective connec- Reinsert the connector. Also check for conti-
two locations occurs 8 times nector. APC PWB M and LSU relay PWB (YC8)
8 times successively. PWB M. 5-25).
7944 Laser scanner unit Y Defective connec- Reinsert the connector. Also check for conti-
two locations occurs 8 times nector. APC PWB Y and LSU relay PWB (YC12)
data and reading data occurs Defective APC Replace the laser scanner unit (see page 1-
PWB Y. 5-25).
1-4-69
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
8010 Punch motor error 1 Defective connec- Reinsert the connector. Also check for conti-
When the punch motor is tor cable or poor nuity within the connector cable. If none,
driven, punch home position contact in the con- replace the cable.
sensor does not turn on within nector (4000-sheet Punch motor and punch PWB (YC4)
200 ms. finisher). Punch home position sensor and punch
PWB (YC8)
Punch PWB (YC1) and DF main PWB (YC7)
nector (1000-sheet Punch motor and punch PWB (YC4)
finisher). Punch home position sensor and punch
PWB (YC8)
Defective punch Replace the punch home position sensor.
home position sen-
sor.
Defective punch Replace the punch motor.
motor.
Defective PWB. Replace the punch PWB or DF main PWB
and check for correct operation.
Home position is not obtained tor cable or poor nuity within the connector cable. If none,
in 3 seconds after home posi- contact in the con- replace the cable.
tion is initialized or in standby. nector (4000-sheet Punch motor and punch PWB (YC4)
finisher). Punch PWB (YC1) and DF main PWB (YC7)
motor.
1-4-70
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
Home position does not turn tor cable or poor nuity within the connector cable. If none,
from On to Off in 50 ms after contact in the con- replace the cable.
home position has been ini- nector (4000-sheet Punch motor and punch PWB (YC4)
tialized. finisher). Punch PWB (YC1) and DF main PWB (YC7)
motor.
8090 DF paddle motor error Defective connec- Reinsert the connector. Also check for conti-
When the DF paddle motor is tor cable or poor nuity within the connector cable. If none,
driven, DF paddle sensor contact in the con- replace the cable.
does not turn on within 1 s. nector (4000-sheet DF paddle motor and DF main PWB (YC15)
finisher). DF paddle sensor and DF main PWB
(YC22)
nector (1000-sheet DF paddle motor and DF main PWB (YC11)
finisher). DF paddle sensor and DF main PWB
(YC20)
Defective DF pad- Replace the DF paddle sensor.
dle sensor.
Defective DF pad- Replace the DF paddle motor.
dle motor.
Defective DF main Replace the DF main PWB and check for
1-4-71
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
8100 DF eject release motor error Defective connec- Reinsert the connector. Also check for conti-
When the DF eject release tor cable or poor nuity within the connector cable. If none,
motor is driven, DF bundle contact in the con- replace the cable.
discharge sensor does not nector (4000-sheet DF eject release motor and DF main PWB
turn on within 1 s. finisher). (YC12)
DF bundle discharge sensor and DF main
PWB (YC22)
nector (1000-sheet DF eject release motor and DF main PWB
finisher). (YC10)
DF bundle discharge sensor and DF main
PWB (YC20)
Defective DF bun- Replace the DF bundle discharge sensor.
dle discharge sen-
sor.
Defective DF eject Replace the DF eject release motor.
release motor.
8110 DF shift motor 1 error Defective connec- Reinsert the connector. Also check for conti-
When the DF shift motor 1 is tor cable or poor nuity within the connector cable. If none,
driven, DF shift sensor 1 does contact in the con- replace the cable.
not turn on within 160 ms. nector. DF shift motor 1 and DF main PWB (YC14)
DF shift sensor 1 and DF main PWB (YC23)
Defective DF shift Replace the DF shift sensor 1.
sensor 1.
Defective DF shift Replace the DF shift motor 1.
motor 1.
8120 DF shift motor 2 error Defective connec- Reinsert the connector. Also check for conti-
When the DF shift motor 2 is tor cable or poor nuity within the connector cable. If none,
driven, DF shift sensor 2 does contact in the con- replace the cable.
not turn on within 160 ms. nector. DF shift motor 2 and DF main PWB (YC14)
DF shift sensor 2 and DF main PWB (YC23)
Defective DF shift Replace the DF shift sensor 2.
sensor 2.
Defective DF shift Replace the DF shift motor 2.
motor 2.
1-4-72
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
8130 DF shift release motor error Defective connec- Reinsert the connector. Also check for conti-
When the DF shift release tor cable or poor nuity within the connector cable. If none,
motor is driven, DF shift contact in the con- replace the cable.
release sensor does not turn nector. DF shift release motor and DF main PWB
on within 1 s. (YC14)
DF shift release sensor and DF main PWB
(YC23)
Defective DF shift Replace the DF shift release sensor.
release sensor.
Defective DF shift Replace the DF shift release motor.
release motor.
8140 DF tray motor error 1 Defective connec- Reinsert the connector. Also check for conti-
When the main tray has tor cable or poor nuity within the connector cable. If none,
started ascending, DF tray contact in the con- replace the cable.
sensor 1 or DF tray upper sur- nector (4000-sheet DF tray motor and DF main PWB (YC16)
face sensor does not turn on finisher). DF tray sensor 1 and DF main PWB (YC22)
within 20 s. DF tray upper surface sensor and DF main
PWB (YC21, YC13)
nector (1000-sheet DF tray motor and DF main PWB (YC14)
finisher). DF tray sensor 1 and DF main PWB (YC20)
DF tray upper surface sensor and DF main
PWB (YC18)
Defective sensor. Replace DF tray sensor 1 or DF tray upper
surface sensor.
Defective DF tray Replace the DF tray motor.
motor.
1-4-73
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
descended, DF tray sensor 1 contact in the con- replace the cable.
or DF tray upper surface sen- nector (4000-sheet DF tray motor and DF main PWB (YC16)
sor does not turn off within finisher). DF tray sensor 1 and DF main PWB (YC22)
5 s. DF tray upper surface sensor and DF main
PWB (YC21, YC13)
DF tray upper surface sensor and DF main
PWB (YC18)
Defective sensor. Replace DF tray sensor 1 or DF tray upper
surface sensor.
motor.
descended, DF tray sensor 3 contact in the con- replace the cable.
does not turn on within 20 s. nector (4000-sheet DF tray motor and DF main PWB (YC16)
Defective DF tray Replace DF tray sensor 3.
sensor 3.
motor.
1-4-74
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
8170 DF side registration motor 1 Defective connec- Reinsert the connector. Also check for conti-
error 1 tor cable or poor nuity within the connector cable. If none,
When initial operation, DF contact in the con- replace the cable.
side registration sensor 1 nector (4000-sheet DF side registration motor 1 and DF main
does not turn on within 3 s. finisher). PWB (YC15)
DF side registration sensor 1 and DF main
PWB (YC22)
nector (1000-sheet DF side registration motor 1 and DF main
finisher). PWB (YC11)
PWB (YC20)
Defective DF side Replace DF side registration sensor 1.
registration sensor
1.
Defective DF side Replace DF side registration motor 1.
registration motor
1.
JAM6810 is detected twice. contact in the con- replace the cable.
PWB (YC22)
PWB (YC20)
registration sensor
1.
registration motor
1.
1-4-75
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
When initial operation, DF contact in the con- replace the cable.
side registration sensor 2 nector (4000-sheet DF side registration motor 2 and DF main
does not turn on within 3 s. finisher). PWB (YC15)
PWB (YC22)
PWB (YC20)
registration sensor
2.
registration motor
2.
JAM6910 is detected twice. contact in the con- replace the cable.
PWB (YC22)
PWB (YC20)
registration sensor
2.
registration motor
2.
1-4-76
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
8210 DF slide motor error Defective connec- Reinsert the connector. Also check for conti-
When initial operation, DF sta- tor cable or poor nuity within the connector cable. If none,
ple sensor does not turn on contact in the con- replace the cable.
within 3 s. nector (4000-sheet DF slide motor and DF main PWB (YC12)
finisher). DF staple sensor and DF main PWB (YC22)
nector (1000-sheet DF slide motor and DF main PWB (YC10)
finisher). DF staple sensor and DF main PWB (YC20)
Defective DF sta- Replace the DF staple sensor.
ple sensor.
Defective DF slide Replace the DF slide motor.
motor.
8230 DF staple motor error Defective connec- Reinsert the connector. Also check for conti-
JAM7000 is detected twice. tor cable or poor nuity within the connector cable. If none,
nector (4000-sheet Staple unit and DF main PWB (YC17)
finisher).
nector (1000-sheet Staple unit and DF main PWB (YC11)
finisher).
Defective DF sta- Replace the staple unit.
ple sensor.
Defective DF sta-
ple motor.
8300 Center-folding unit commu- Defective connec- Reinsert the connector. Also check for conti-
Communication with the cen- contact in the con- replace the cable.
ter-folding unit is not possible. nector. CF main PWB (YC7) and DF main PWB
(YC9)
Defective CF set Replace the CF set sensor.
sensor.
Defective PWB. Replace the CF main PWB or the DF main
PWB and check for correct operation.
1-4-77
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
8310 CF side registration motor 2 Defective connec- Reinsert the connector. Also check for conti-
When initial operation, CF contact in the con- replace the cable.
side registration sensor 2 nector. CF side registration motor 2 and CF main
does not turn on within 1 s. PWB (YC10)
CF side registration sensor 2 and CF main
PWB (YC20)
Defective CF side Replace CF side registration sensor 2.
registration sensor
2.
Defective CF side Replace CF side registration motor 2.
registration motor
2.
Defective CF main Replace the CF main PWB and check for
8320 CF adjustment motor error Defective connec- Reinsert the connector. Also check for conti-
When initial operation, CF tor cable or poor nuity within the connector cable. If none,
adjustment sensor does not contact in the con- replace the cable.
turn on within 2.5 s. nector. CF adjustment motor 1, 2 and CF main PWB
(YC10)
CF adjustment sensor 1, 2 and CF main
PWB (YC20)
Defective CF Replace CF adjustment sensor 1, 2.
adjustment sensor
1, 2.
Defective CF Replace CF adjustment motor 1, 2.
adjustment motor
1, 2.
8330 CF blade motor error Defective connec- Reinsert the connector. Also check for conti-
When initial operation, CF tor cable or poor nuity within the connector cable. If none,
blade sensor does not turn on contact in the con- replace the cable.
within 1.5 s. nector. CF blade motor and CF main PWB (YC15)
CF blade sensor and CF main PWB (YC20)
Defective CF blade Replace the CF blade sensor.
sensor.
Defective CF blade Replace the CF blade motor.
motor.
1-4-78
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
8340 CF staple motor error Defective connec- Reinsert the connector. Also check for conti-
JAM7600 is detected twice. tor cable or poor nuity within the connector cable. If none,
nector. CF staple unit and CF main PWB (YC13)
Defective CF sta- Replace the CF staple unit.
ple sensor.
Defective CF sta-
ple motor.
8350 CF side registration motor 1 Defective connec- Reinsert the connector. Also check for conti-
When initial operation, CF contact in the con- replace the cable.
side registration sensor 1 nector. CF side registration motor 1 and CF main
does not turn on within 1 s. PWB (YC10)
CF side registration sensor 1 and CF main
PWB (YC20)
Defective CF side Replace CF side registration sensor 1.
registration sensor
1.
Defective CF side Replace CF side registration motor 1.
registration motor
1.
8360 CF main motor error Defective connec- Reinsert the connector. Also check for conti-
During driving the motor, lock tor cable or poor nuity within the connector cable. If none,
signal is detected for 1 s con- contact in the con- replace the cable.
tinuously. nector. CF main motor and CF main PWB (YC16)
Defective CF main Replace the CF main motor.
motor.
1-4-79
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
8410 Punch slide motor error 1 Defective connec- Reinsert the connector. Also check for conti-
The punch slide sensor won’t tor cable or poor nuity within the connector cable. If none,
turn On when home position contact in the con- replace the cable.
has been moved by 30 mm. nector (4000-sheet Punch slide motor and punch PWB (YC3)
finisher). Punch slide sensor and punch PWB (YC6)
nector (1000-sheet Punch slide motor and punch PWB (YC3)
finisher). Punch slide sensor and punch PWB (YC6)
Defective slide Replace the punch slide sensor.
sensor.
Defective punch Replace the punch slide motor.
slide motor.
8420 Punch slide motor error 2 Defective connec- Reinsert the connector. Also check for conti-
In detection of paper edges, tor cable or poor nuity within the connector cable. If none,
the paper edge cannot be contact in the con- replace the cable.
detected in 30 mm move. nector (4000-sheet Punch slide motor and punch PWB (YC3)
nector (1000-sheet Punch slide motor and punch PWB (YC3)
Defective punch Replace the punch slide motor.
slide motor.
8430 Punch unit communication Defective connec- Reinsert the connector. Also check for conti-
Communication with the contact in the con- replace the cable.
punch unit is not possible. nector (4000-sheet Punch PWB (YC1) and DF main PWB (YC7)
finisher).
nector (1000-sheet Punch PWB (YC1) and DF main PWB (YC8)
finisher).
Defective PWB. Replace the punch PWB or the DF main
1-4-80
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
8500 Mailbox communication Defective connec- Reinsert the connector. Also check for conti-
Communication with the mail- contact in the con- replace the cable.
box is not possible. nector. MB main PWB (YC3) and DF main PWB
(YC6)
Defective PWB. Replace the MB main PWB or the DF main
8510 MB conveying motor error 1 Defective connec- Reinsert the connector. Also check for conti-
When initial operation, MB tor cable or poor nuity within the connector cable. If none,
home position sensor does contact in the con- replace the cable.
not turn on within 5 s. nector. MB conveying motor and MB main PWB
(YC5)
MB home position sensor and MB main
PWB (YC2)
Defective MB Replace the MB home position sensor.
home position sen-
sor.
Defective MB con- Replace the MB conveying motor.
veying motor.
Defective MB main Replace the MB main PWB and check for
8520 MB conveying motor error 2 Defective connec- Reinsert the connector. Also check for conti-
When standby operation, MB tor cable or poor nuity within the connector cable. If none,
home position sensor does contact in the con- replace the cable.
not turn off within 1 s. nector. MB conveying motor and MB main PWB
(YC5)
MB home position sensor and MB main
PWB (YC2)
Defective MB Replace the MB home position sensor.
home position sen-
sor.
Defective MB con- Replace the MB conveying motor.
veying motor.
Defective MB main Replace the MB main PWB and check for
1-4-81
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
8800 Document finisher commu- Defective connec- Reinsert the connector. Also check for conti-
Communication with the docu- contact in the con- replace the cable.
ment finisher is not possible. nector (4000-sheet DF main PWB (YC4) and engine PWB
finisher). (YC18)
nector (1000-sheet DF main PWB (YC7) and engine PWB
finisher). (YC18)
Defective PWB. Replace the DF main PWB or the engine
8900 Document finisher backup Defective connec- Reinsert the connector. Also check for conti-
Read and write data does not contact in the con- replace the cable.
match 3 times in succession. nector (4000-sheet DF main PWB (YC4) and engine PWB
finisher). (YC18)
nector (1000-sheet DF main PWB (YC7) and engine PWB
finisher). (YC18)
Improper installa- Check the installation of the EEPROM and
tion EEPROM. remedy if necessary.
8930 Center-folding unit backup Defective connec- Reinsert the connector. Also check for conti-
Read and write data does not contact in the con- replace the cable.
match 3 times in succession. nector. CF main PWB (YC7) and DF main PWB
(YC9)
Improper installa- Check the installation of the EEPROM and
tion EEPROM. remedy if necessary.
9000 Document processor com- Defective connec- Reinsert the connector. Also check for conti-
munication error tor cable or poor nuity within the connector cable. If none,
Communication with the docu- contact in the con- replace the cable.
ment processor is not possi- nector. DP main PWB (YC1) and ISC PWB (YC12)
ble. ISC PWB (YC3) and main PWB (YC11)
Defective PWB. Replace the DP main PWB or the ISC PWB
1-4-82
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
9010 Coin vender communica- Defective connec- Reinsert the connector. Also check for conti-
tion error tor cable or poor nuity within the connector cable. If none,
A communication error from contact in the con- replace the cable.
coin vender is detected 10 nector.
times in succession. Data setup failure. Set maintenance mode U206 to off when a
coin vender is not installed.
Defective coin Replace the coin vender control PWB.
vender control
PWB.
Defective PWB. Replace the main PWB and check for cor-
rect operation (see page 1-5-49).
9040 DP lift motor going up error Defective connec- Reinsert the connector. Also check for conti-
When the DP lift motor is tor cable or poor nuity within the connector cable. If none,
driven, DP lift sensor 1 does contact in the con- replace the cable.
not turn on within 2 s. nector. DP lift motor and DP main PWB (YC5)
DP lift sensor 1 and DP main PWB (YC4)
Defective DP lift Replace the DP lift sensor 1.
sensor 1.
Defective DP lift Replace the DP lift motor.
motor.
9050 DP lift motor going down Defective connec- Reinsert the connector. Also check for conti-
When the DP lift motor is contact in the con- replace the cable.
driven, DP lift sensor 2 does nector. DP lift motor and DP main PWB (YC5)
not turn on within 2 s. DP lift sensor 2 and DP main PWB (YC2)
Defective DP lift Replace the DP lift sensor 2.
sensor 2.
Defective DP lift Replace the DP lift motor.
motor.
9060 DP EEPROM error Defective DP main Replace the DP main PWB and check for
Mismatch of reading data from PWB. correct operation.
two locations occurs 3 times Device damage of Contact the Service Administrative Division.
successively. EEPROM.
1-4-83
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
between DP and SHD tor cable or poor nuity within the connector cable. If none,
A communication error is contact in the con- replace the cable.
detected. nector. ISC PWB and DP main PWB (YC1)
PWB. operation.
between DP and CIS tor cable or poor nuity within the connector cable. If none,
A communication error is contact in the con- replace the cable.
detected. nector. DPSHD PWB and DP main PWB (YC10)
DPSHD PWB and DP relay PWB (YC2)
Defective CIS. Replace CIS and check for correct opera-
tion.
Defective DPSHD Replace the DPSHD PWB and check for
9100 Coin vender control PWB Defective coin Replace the coin mec.
error vender control
Communication error has PWB.
been detected at the coin mec
of the coin vender control
PWB.
9110 Coin vender error Rejector installed Check the rejector is properly installed and,
Communication error has incorrectly. if not, perform the corrective action.
been detected in connection Defective rejector. Replace the rejector.
with the coin mec and the
rejector.
9120 Sensor error in coin vender Coin jam in the Check visually and remedy.
change (Yen 10) change tube
Change is empty despite
Poor contact in the Check if the change empty sensor is intact.
change is enough.
connector.
Defective change Replace the coin mec.
empty sensor.
Defective coin Replace the coin mec.
vender control
PWB.
Change is empty despite Poor contact in the Check if the change empty sensor is intact.
change is enough. connector.
empty sensor.
vender control
PWB.
1-4-84
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
Change is empty despite
Poor contact in the Check if the change empty sensor is intact.
change is enough.
connector.
empty sensor.
vender control
PWB.
Change is empty despite Poor contact in the Check if the change empty sensor is intact.
change is enough. connector.
empty sensor.
vender control
PWB.
9160 Coin vender pay-out error Defective pay-out Replace the coin mec.
Coin is paid out despite the motor.
pay-out motor is determined
not active.
9170 Coin vender pay-out sensor Change jam at the Check visually and remedy.
error pay-out.
Coin is paid out despite the
Defective pay-out Replace the coin mec.
pay-out motor is determined
motor.
not active.
Defective pay-out Replace the coin mec.
sensor.
9500 Contact the Service Administrative Division.
F000 Communication error Defective main Turn the main power switch off/on to restart
between main PWB and PWB. the machine. If the error is not resolved,
operation PWB replace main PWB (see page 1-5-49).
Defective opera- Replace the operation PWB and check for
tion PWB. correct operation.
F010 Main PWB checksum error Defective main Turn the main power switch off/on to restart
PWB. the machine. If the error is not resolved,
replace main PWB (see page 1-5-49).
1-4-85
2LK/2LN/2LM/2LC
Check procedures/
corrective measures
print engine replace main PWB (see page 1-5-49).
scanner engine replace main PWB (see page 1-5-49).
F050 Print engine ROM check- Defective engine Turn the main power switch off/on to restart
sum error PWB. the machine. If the error is not resolved,
replace engine PWB (see page 1-5-54).
between main PWB and fax PWB. the machine. If the error is not resolved,
control PWB replace main PWB (see page 1-5-49).
Defective fax con- Replace the fax control PWB and check for
F278 Power supply in drive sys- Main power switch Turn on power.
tem error was turned off (To switch off power, first press the power
without using the key until the main power indicator goes off,
power key, or a then turn the main power switch off.)
power failure has
occurred.
1-4-86
2LK/2LN/2LM/2LC
1-4-3 Image formation problems

(1) No image (2) No image (3) Image is too (4) The back- (5) White streaks
appears (entirely appears (entirely light. ground is col- are printed verti-
white). black). ored. cally.
See page 1-4-88 See page 1-4-89 See page 1-4-90 See page 1-4-90 See page 1-4-91
(6) Black streaks (7) Streaks are (8) One side of the (9) Spots are (10)Image is
are printed verti- printed horizon- print image is printed. blurred.
cally. tally. darker than the
other.
(11) The leading (12)The leading (13)Paper is wrin- (14)Offset occurs. (15)Part of image is
edge of the edge of the kled. missing.
image is con- image is spo-
sistently mis- radically mis-
aligned with the aligned with the
original. original.
(16)Fusing is loose. (17)Image is out of (18)Image center
focus. does not align
with the original
center.
See page 1-4-94 See page 1-4-95 See page 1-4-95
1-4-87
2LK/2LN/2LM/2LC
(1) No image appears (entirely white).

Print example Causes Check procedures/corrective measures
Defective Defective connector cable Reinsert the connector. Also check for conti-
transfer or poor contact in the con- nuity within the connector cable. If none,
bias output. nector. replace the cable.
High voltage PWB 2 (YC1) and engine PWB
(YC8)
Defective high voltage PWB Replace the high voltage PWB 2
2. (see page 1-5-60).
Defective engine PWB. Replace the engine PWB (see page 1-5-54).
Defective Defective connector cable Reinsert the connector. Also check for conti-
developer or poor contact in the con- nuity within the connector cable. If none,
bias output. nector. replace the cable.
High voltage PWB 1 (YC1, 2) and engine
PWB (YC16)
PWB (YC17)
1. (see page 1-5-59).
No LSU Defective laser scanner Replace the laser scanner unit
laser is out- unit. (see page 1-5-25).
put. Defective engine PWB. Replace the engine PWB (see page 1-5-54).
1-4-88
2LK/2LN/2LM/2LC
(2) No image appears (entirely black).

No main Defective connector cable Reinsert the connector. Also check for conti-
charging. or poor contact in the con- nuity within the connector cable. If none,
nector. replace the cable.
PWB (YC16)
PWB (YC17)
Defective charger roller unit. Replace the charger roller unit
(see page 1-5-38).
1. (see page 1-5-59).
Exposure Defective connector cable Reinsert the connector. Also check for conti-
lamp fails to or poor contact in the con- nuity within the connector cable. If none,
light. nector. replace the cable.
LED PWB and ISC PWB (CN6)
Defective exposure lamp. Replace the LED PWB (see page 1-5-19).
Defective ISC PWB. Replace the ISC PWB.
Defective main PWB. Replace the main PWB (see page 1-5-49).
The laser is Defective laser scanner Replace the laser scanner unit
activated unit. (see page 1-5-25).
simultane-
ously for all
colors.
1-4-89
2LK/2LN/2LM/2LC
(3) Image is too light.

Defective Defective developer unit. Run maintenance mode U089 to output four-
developer color bar PG, check the output status of the
bias output. four colors, and replace the developer unit for
any faulty color (see page 1-5-36).
1. (see page 1-5-59).
Dirty drum unit. Perform the drum refresh.
Defective Defective high voltage PWB Replace the high voltage PWB 2
transfer 2. (see page 1-5-60).
bias output. Defective transfer belt unit. Replace the transfer belt unit (see page 1-5-
41).
Defective color calibration. Perform the color calibration (Refer to opera-
tion guide).
Insufficient toner. If the display shows the message requesting
toner replenishment, replace the container.
Insufficient agitation of toner container. Shake the toner container vertically approxi-
mately 10 times.
Paper damp. Check the paper storage conditions, replace
the paper.
(4) The background is colored.

Defective Defective developer unit. Run maintenance mode U089 to output four-
developer color bar PG, check the output status of the
bias output. four colors, and replace the developer unit for
any faulty color (see page 1-5-36).
1. (see page 1-5-59).
Defective color calibration. Perform the color calibration (Refer to opera-
tion guide).
1-4-90
2LK/2LN/2LM/2LC
(5) White streaks are printed vertically.

Foreign object in one of the Run maintenance mode U089 to output four-color bar PG,
developer units. check the output status of the four colors, and replace the
developer unit for any faulty color (see page 1-5-36).
Dirty transfer belt. Clean the transfer belt. Replace the transfer belt unit if it is
extremely dirty (see page 1-5-41).
Dirty transfer roller. Clean the transfer roller. Replace the transfer roller if it is
Dirty shading plate. Clean the shading plate.
Dirty scanner mirror. Clean the scanner mirror.
Dirty LSU slit glasses. Perform the laser scanner cleaning.
Dirty contact glass. Clean the contact glass.
(6) Black streaks are printed vertically.

Dirty slit glass. Clean the slit glass.
Dirty or flawed drum. Perform the drum refresh.
Flawed drum. Replace the drum unit (see page 1-5-36).
Deformed or worn cleaning Replace the drum unit (see page 1-5-36).
blade in the drum unit.
Dirty lens of ISU. Clean lens of ISU.
Worn transfer belt. Replace the transfer belt unit (see page 1-5-41).
Defective transfer roller. Replace the transfer roller (see page 1-5-43).
Dirty scanner mirror. Clean the scanner mirror.
(7) Streaks are printed horizontally.

Dirty developer section. Clean any part contaminated with toner in the developer
section.
Poor contact of grounding ter- Check the installation of the drum unit. If it operates incor-
minal of drum unit. rectly, replace it (see page 1-5-36).
1-4-91
2LK/2LN/2LM/2LC
(8) One side of the print image is darker than the other.
Defective exposure lamp. Replace the LED unit (see page 1-5-19).
(9) Spots are printed.

Flawed developer roller. Replace the developer unit (see page 1-5-36).
Dirty heat roller and press Clean the heat roller and press roller.
roller.
(10) Image is blurred.

Scanner moves erratically. Check if there is any foreign matter on the front and rear
scanner rails. If any, remove it.
Deformed press roller. Replace the fuser unit (see page 1-5-45).
Paper conveying section drive Check the gears and belts and, if necessary, grease them.
problem.
1-4-92
2LK/2LN/2LM/2LC
(11) The leading edge of the image is consistently misaligned with the original.
Misadjusted leading edge reg- Run maintenance mode U034 to readjust the leading edge
istration. registration (see page 1-3-33).
Misadjusted the deflection in Run maintenance mode U051 to readjust the deflection in
the paper. the paper (see page 1-3-40).
Misadjusted scanner leading Run maintenance mode U066 to readjust the scanner
edge registration. leading edge registration (see page 1-3-53).
(12) The leading edge of the image is sporadically misaligned with the original.
Paper feed clutch, middle Check the installation of the clutch. If it operates incor-
clutch, registration clutch or rectly, replace it.
duplex clutch operating incor-
rectly. (30 ppm/35 ppm model)
Paper feed clutch, middle Check the installation of the clutch or motor. If it operates
motor, registration motor or incorrectly, replace it.
duplex motor operating incor-
rectly. (45 ppm/55 ppm model)
(13) Paper is wrinkled.

Paper curled. Check the paper storage conditions.
Paper damp. Check the paper storage conditions.
Defective pressure springs. Replace the fuser unit (see page 1-5-45).
1-4-93
2LK/2LN/2LM/2LC
(14) Offset occurs.

Defective transfer belt clean- Replace the transfer belt unit (see page 1-5-41).
ing.
Defective fuser unit. Replace the fuser unit (see page 1-5-45).
Wrong types of paper. Check if the paper meets specifications. Replace paper.
(15) Part of image is missing.

Paper damp. Check the paper storage conditions.
Paper creased. Replace the paper.
Drum condensation. Perform the drum refresh.
Dirty transfer belt. Clean the transfer belt. Replace the transfer belt unit if it is
Dirty transfer roller. Clean the transfer roller. Replace the transfer roller if it is
Dirt on the back surface of the Clean the contact glass and scanner mirror.
contact glass and scanner
mirror.
(16) Fusing is loose.

Wrong types of paper. Check if the paper meets specifications, replace paper.
Flawed heat roller or press Replace the fuser unit (see page 1-5-45).
roller.
Defective pressure springs.
Defective fuser IH.
1-4-94
2LK/2LN/2LM/2LC
(17) Image is out of focus.

Defective image scanning Replace the image scanning unit (see page 1-5-22).
unit.
Drum condensation. Perform the drum refresh.
(18) Image center does not align with the original center.
Misadjusted image center Run maintenance item U034 to readjust the center line of
line. image printing (see page 1-3-36).
Misadjusted scanner center Run maintenance item U067 to readjust the scanner lead-
line. ing edge registration (see page 1-3-54).
Original is not placed cor- Place the original correctly.
rectly.
Paper is not placed correctly. Place the paper correctly.
1-4-95
2LK/2LN/2LM/2LC
1-4-4 Electric problems

Troubleshooting to each failure must be in the order of the numbered symptoms.
Problem Causes Check procedures/corrective measures

(1) 1. No electricity at the Measure the input voltage.
The machine does power outlet.
not operate when
2. The power cord is Check the contact between the power plug and the outlet.
the main power
not plugged in prop-
switch is turned on.
erly.
3. Broken power cord. Check for continuity. If none, replace the cord.
4. Defective main Check for continuity across the contacts. If none, replace
power switch. the power source PWB (see page 1-5-56).
5. Defective power Replace the power source PWB (see page 1-5-56).
source PWB.
(2) 1. Defective connector Reinsert the connector. Also check for continuity within the
MP lift motor does cable or poor con- connector cable. If none, replace the cable.
not operate. tact in the connector. MP lift motor and relay PWB (YC3)
Relay PWB (YC12) and engine PWB (YC17)
2. Defective drive trans- Check if the rollers and gears rotate smoothly. If not,
mission system. grease the bushes and gears. Check for broken gears and
replace if any.
3. Defective motor. Replace the MP lift motor.
4. Defective PWB. Replace the engine PWB and check for correct operation
(see page 1-5-54).
Scanner motor cable or poor con- connector cable. If none, replace the cable.
does not operate. tact in the connector. Scanner motor and ISC PWB (YC5)
replace if any.
3. Defective motor. Replace the scanner motor.
4. Defective PWB. Replace the main PWB and check for correct operation
(see page 1-5-49).
Registration motor cable or poor con- connector cable. If none, replace the cable.
does not operate tact in the connector. Registration motor and feed PWB 1 (YC25)
(45 ppm/55 ppm Feed PWB 1 (YC2) and engine PWB (YC5)
model only). 2. Defective drive trans- Check if the rollers and gears rotate smoothly. If not,
replace if any.
3. Defective motor. Replace the registration motor.
(see page 1-5-54).
1-4-96
2LK/2LN/2LM/2LC

Middle motor does cable or poor con- connector cable. If none, replace the cable.
not operate tact in the connector. Middle motor and feed PWB 2 (YC7)
model only).
replace if any.
3. Defective motor. Replace the middle motor.
(see page 1-5-54).
Eject motor does cable or poor con- connector cable. If none, replace the cable.
not operate. tact in the connector. Eject motor and front PWB (YC5)
replace if any.
3. Defective motor. Replace the eject motor.
(see page 1-5-54).
Duplex motor 1 cable or poor con- connector cable. If none, replace the cable.
does not operate tact in the connector. Duplex motor 1 and relay PWB (YC16)
(45 ppm/55 ppm Relay PWB (YC13) and engine PWB (YC23)
model only).
replace if any.
3. Defective motor. Replace the duplex motor 1.
(see page 1-5-54).
Duplex motor 2 cable or poor con- connector cable. If none, replace the cable.
does not operate tact in the connector. Duplex motor 2 and relay PWB (YC7)
model only). 2. Defective drive trans- Check if the rollers and gears rotate smoothly. If not,
replace if any.
3. Defective motor. Replace the duplex motor 2.
(see page 1-5-54).
1-4-97
2LK/2LN/2LM/2LC

Toner fan motor 1, cable or poor con- connector cable. If none, replace the cable.
2 does not operate. tact in the connector. Toner fan motor 1, 2 and engine PWB (YC19)
2. Defective motor. Replace the toner fan motor 1 or 2.
(see page 1-5-54).
Developer fan cable or poor con- connector cable. If none, replace the cable.
motor 1, 2 does not tact in the connector. Developer fan motor 1, 2 and front PWB (YC6)
operate. Front PWB (YC3) and engine PWB (YC7)
2. Defective motor. Replace the Developer fan motor 1 or 2.
(see page 1-5-54).
LSU fan motor cable or poor con- connector cable. If none, replace the cable.
does not operate. tact in the connector. LSU fan motor and front PWB (YC16)
2. Defective motor. Replace the LSU fan motor.
(see page 1-5-54).
Belt fan motor 1, 2 cable or poor con- connector cable. If none, replace the cable.
does not operate. tact in the connector. Belt fan motor 1, 2 and engine PWB (YC19)
2. Defective motor. Replace the Belt fan motor 1 or 2.
(see page 1-5-54).
Fuser fan motor 1, cable or poor con- connector cable. If none, replace the cable.
2 does not operate. tact in the connector. Fuser fan motor 1, 2 and relay PWB (YC16)
2. Defective motor. Replace the fuser fan motor 1 or 2.
(see page 1-5-54).
Eject fan motor 1, cable or poor con- connector cable. If none, replace the cable.
2 does not operate. tact in the connector. Eject fan motor 1, 2 and relay PWB (YC11)
2. Defective motor. Replace the eject fan motor 1 or 2.
(see page 1-5-54).
1-4-98
2LK/2LN/2LM/2LC

Eject front fan cable or poor con- connector cable. If none, replace the cable.
motor does not tact in the connector. Eject front fan motor and front PWB (YC4)
operate. Front PWB (YC3) and engine PWB (YC7)
2. Defective motor. Replace the eject front fan motor.
(see page 1-5-54).
Eject rear fan cable or poor con- connector cable. If none, replace the cable.
motor does not tact in the connector. Eject rear fan motor and feed PWB 1 (YC19)
operate. Feed PWB 1 (YC1) and engine PWB (YC6)
2. Defective motor. Replace the eject rear fan motor.
(see page 1-5-54).
Power source fan cable or poor con- connector cable. If none, replace the cable.
motor does not tact in the connector. Power source fan motor and engine PWB (YC22)
operate. 2. Defective motor. Replace the power source fan motor.
(see page 1-5-54).
Controller fan cable or poor con- connector cable. If none, replace the cable.
motor does not tact in the connector. Controller fan motor and main PWB (YC23)
operate. 2. Defective motor. Replace the controller fan motor.
3. Defective PWB. Replace the main PWB and check for correct operation
(see page 1-5-49).
Paper feed clutch cable or poor con- connector cable. If none, replace the cable.
1, 2 does not oper- tact in the connector. Paper feed clutch 1, 2 and feed PWB 2 (YC4)
ate. Feed PWB 2 (YC1) and engine PWB (YC4)
2. Defective clutch. Replace the paper feed clutch 1 or 2.
(see page 1-5-54).
Assist clutch 1, 2 cable or poor con- connector cable. If none, replace the cable.
does not operate tact in the connector. Assist clutch 1 and feed PWB 2 (YC10)
(45 ppm/55 ppm Assist clutch 2 and feed PWB 2 (YC12)
model only). Feed PWB 2 (YC1) and engine PWB (YC4)
2. Defective clutch. Replace the assist clutch 1 or 2.
(see page 1-5-54).
1-4-99
2LK/2LN/2LM/2LC

Paper conveying cable or poor con- connector cable. If none, replace the cable.
clutch does not tact in the connector. Paper conveying clutch and feed PWB 2 (YC5)
operate. Feed PWB 2 (YC1) and engine PWB (YC4)
2. Defective clutch. Replace the paper conveying clutch.
(see page 1-5-54).
MP paper feed cable or poor con- connector cable. If none, replace the cable.
clutch does not tact in the connector. MP paper feed clutch and relay PWB (YC3)
operate. Relay PWB (YC12) and engine PWB (YC17)
2. Defective clutch. Replace the MP paper feed clutch.
(see page 1-5-54).
Registration clutch cable or poor con- connector cable. If none, replace the cable.
does not operate tact in the connector. Registration clutch and feed PWB 1 (YC22)
model only). 2. Defective clutch. Replace the registration clutch.
(see page 1-5-54).
Middle clutch does cable or poor con- connector cable. If none, replace the cable.
not operate tact in the connector. Middle clutch and feed PWB 2 (YC7)
model only).
2. Defective clutch. Replace the middle clutch.
(see page 1-5-54).
Duplex clutch 1 cable or poor con- connector cable. If none, replace the cable.
does not operate tact in the connector. Duplex clutch 1 and relay PWB (YC11)
model only).
2. Defective clutch. Replace the Duplex clutch 1.
(see page 1-5-54).
Duplex clutch 2 cable or poor con- connector cable. If none, replace the cable.
does not operate tact in the connector. Duplex clutch 2 and relay PWB (YC7)
model only). 2. Defective clutch. Replace the Duplex clutch 2.
(see page 1-5-54).
1-4-100
2LK/2LN/2LM/2LC

Pickup solenoid 1, cable or poor con- connector cable. If none, replace the cable.
2 does not operate tact in the connector. Pickup solenoid 1, 2 and feed PWB 2 (YC8)
model only).
2. Defective solenoid. Replace the pickup solenoid 1 or 2.
(see page 1-5-54).
Feedshift solenoid cable or poor con- connector cable. If none, replace the cable.
does not operate. tact in the connector. Feedshift and front PWB (YC5)
2. Defective solenoid. Replace the feedshift solenoid 1 or 2.
(see page 1-5-54).
Cleaning solenoid cable or poor con- connector cable. If none, replace the cable.
does not operate. tact in the connector. Cleaning solenoid and feed PWB 1 (YC10)
2. Defective solenoid. Replace the pickup solenoid 1 or 2.
(see page 1-5-54).
The message cable or poor con- connector cable. If none, replace the cable.
requesting paper to tact in the connector. Paper sensor 1, 2 and feed PWB 2 (YC8)
be loaded is shown Feed PWB 2 (YC1) and engine PWB (YC4)
when paper is
2. Deformed actuator. Check visually and replace if necessary.
present on the cas-
sette. 3. Defective sensor. Replace the paper sensor 1 or 2.
(see page 1-5-54).
The message cable or poor con- connector cable. If none, replace the cable.
requesting paper to tact in the connector. MP paper sensor and relay PWB (YC3)
be loaded is shown Relay PWB (YC12) and engine PWB (YC17)
when paper is
2. Deformed actuator. Check visually and replace if necessary.
present on the MP
tray. 3. Defective sensor. Replace the MP paper sensor.
(see page 1-5-54).
1-4-101
2LK/2LN/2LM/2LC

The size of paper cable or poor con- connector cable. If none, replace the cable.
on the cassette is tact in the connector. Paper length switch 1, 2 and feed PWB 2 (YC3)
not displayed cor- Paper width switch 1, 2 and feed PWB 2 (YC3)
rectly. Feed PWB 2 (YC1) and engine PWB (YC4)
2. Defective switch. Replace the paper length switch 1, 2 or paper width switch
1, 2.
(see page 1-5-54).
The size of paper cable or poor con- connector cable. If none, replace the cable.
on the MP tray is tact in the connector. MP paper length switch and relay PWB (YC2)
not displayed cor- MP paper width switch and relay PWB (YC2)
rectly. Relay PWB (YC12) and engine PWB (YC17)
2. Defective switch. Replace the MP paper length switch or MP paper width
switch.
(see page 1-5-54).
(34) 1. A piece of paper torn Check visually and remove it, if any.
A paper jam in the from paper is caught
paper feed, paper around feed sensor
conveying or eject 1, 2, MP feed sensor,
section is indi- middle sensor, paper
cated when the conveying sensor,
main power switch registration sensor,
is turned on. loop sensor, fuser
eject sensor, duplex
sensor 1, 2, eject full
sensor or switch-
back sensor.
2. Defective sensor. Replace the feed sensor 1, 2, MP feed sensor, middle sen-
sor, paper conveying sensor, registration sensor, loop sen-
sor, fuser eject sensor, duplex sensor 1, 2, eject full sensor
or switchback sensor.
A message indicat- cable or poor con- connector cable. If none, replace the cable.
ing cover open is tact in the connector. Front cover switch and front PWB (YC16)
displayed when the Front PWB (YC2) and engine PWB (YC10)
front cover is 2. Defective switch. Replace the front cover switch.
closed.
ing unit open is dis- tact in the connector. Paper conveying unit switch and feed PWB 1 (YC15)
played when the Feed PWB 1 (YC4) and power source PWB (YC12)
paper conveying
2. Defective switch. Replace the paper conveying unit switch.
unit is closed.
1-4-102
2LK/2LN/2LM/2LC

ing cover open is tact in the connector. Duplex cover switch and relay PWB (YC7)
displayed when the Relay PWB (YC1) and engine PWB (YC14)
duplex cover is
2. Defective switch. Replace the duplex cover switch.
closed.
ing cover open is tact in the connector. Paper conveying cover switch and feed PWB 2 (YC6)
displayed when the Feed PWB 2 (YC14) and power source PWB (YC4)
paper conveying 2. Defective switch. Replace the paper conveying cover switch.
cover is closed.
1-4-103
2LK/2LN/2LM/2LC
1-4-5 Mechanical problems

Problem Causes/check procedures Corrective measures

(1) Check if the surfaces of the following roll- Clean with isopropyl alcohol.
No primary paper ers are dirty with paper powder.
feed. Forwarding pulley
Paper feed pulley
MP paper feed pulley
Check if the following rollers is deformed. Check visually and replace any
Forwarding pulley deformed (see page 1-5-7, 1-5-10, 1-5-
Paper feed pulley 14).
MP paper feed pulley
Defective paper feed clutch 1, 2 installa- Check visually and remedy if necessary.
tion.
(2) Check if the surfaces of the following roll- Clean with isopropyl alcohol.
No secondary paper ers are dirty with paper powder.
feed. Right registration roller
Left registration roller
Defective registration motor installation. Check visually and remedy if necessary.
(45 ppm/55 ppm model)
Defective registration clutch installation.
(30 ppm/35 ppm model)
(3) Paper width guide in a cassette installed Check the paper width guide visually
Skewed paper feed. incorrectly. and remedy or replace if necessary.
(4) Check if the paper is excessively curled. Change the paper.
Multiple sheets of
Paper is loaded incorrectly. Load the paper correctly.
paper are fed.
Check if the separation pulley is worn. Replace the separation pulley if it is
worn (see page 1-5-7, 1-5-10).
(5) Check if the paper is excessively curled. Change the paper.
Paper jams.
Check if the contact between the right Check visually and remedy if necessary.
and left registration rollers is correct.
Check if the heat roller or press roller is Check visually and replace the fuser
extremely dirty or deformed. unit (see page 1-5-45).
(6) Check if the drum unit or developer unit Clean the drum unit or developer unit.
Toner drops on the is extremely dirty.
paper conveying path.
1-4-104
2LK/2LN/2LM/2LC
Problem Causes/check procedures Corrective measures

(7) Check if the rollers, pulleys and gears Grease the bushes and gears.
Abnormal noise is operate smoothly.
heard.
Check if the following clutches are Check visually and remedy if necessary.
installed correctly.
Paper feed clutch 1, 2
Assist clutch 1, 2*1
Paper conveying clutch
MP paper feed clutch
Registration clutch*2
Middle clutch*2
Duplex clutch 1, 2*2
*1: 45 ppm/55 ppm model only
*2: 30 ppm/35 ppm model only
1-4-105
2LK/2LN/2LM/2LC
1-4-6 Send error code

This section describes the scanning errors and descriptions, preventive actions, as well as corrective actions.
Error codes not described here could fall within software errors.
If such an error is encountered, turn power off then on, and advise the service representative.
(1) Scan to SMB error codes

Code Contents Check procedures/corrective measures
1101 Host destined does not exist on the net- 1. Confirm destined host.
work. 2. Confirm device's network parameters.
3. Confirm the network parameters the device is con-
nected.
1102 Login to the host has failed. 1. Confirm user name and password.
nected.
3. Check the host if the folder is properly shared.
1103 Destined host, folder, and/or file names 1. Check illegal characters are not contained within
are invalid. these names.
2. Check the name of the folder and files conform with
the naming syntax.
3. Confirm destined host and folder.
1105 SMB protocol is not enabled. 1. Confirm device's SMB protocols.
2101 Login to the host has failed. 1. Confirm destined host.
2. Confirm that the LAN cable is properly connected to
the device.
3. Check the SMB port number.
4. Confirm device's network parameters.
nected.
2201 Writing scanned data has failed. 1. Check the scanning file name.
nected.
1-4-106
2LK/2LN/2LM/2LC
(2) Scan to FTP error codes

1101 FTP server does not exist on the net- 1. Check the FTP server name.
work. 2. Confirm device's network parameters.
nected.
1102 Login to the FTP server has failed. 1. Confirm user name and password.
2. Check the FTP server name.
1103 Destined folder is invalid. 1. Check illegal characters are not contained within
these names.
1105 FTP protocol is not enabled. 1. Confirm device's FTP protocols.
1131 Initializing TLS has failed. 1. Confirm device's security parameters.
1132 TLS negotiation has failed. 1. Confirm device's security parameters.
2101 Access to the FTP server has failed. 1. Check the FTP server name.
2. Confirm that the LAN cable is properly connected to
the device.
3. Check the FTP port number.
nected.
2102 Access to the FTP server has failed. 1. Check the FTP server name.
(Connection timeout) 2. Check the FTP port number.
nected.
2201 Connection with the FTP server has 1. Confirm device's network parameters.
failed. 2. Confirm the network parameters the device is con-
nected.
3. Confirm destined folder.
(Timeout) nected.
(FTPS communication) nected.
3101 FTP server responded with an error. 1. Confirm device's network parameters.
nected.
3. Check the FTP server.
1-4-107
2LK/2LN/2LM/2LC
(3) Scan to E-mail error codes

1101 SMTP/POP3 server does not exist on 1. Check the SMTP/POP3 server name.
the network. 2. Confirm device's network parameters.
nected.
1102 Login to the SMTP/POP3 server has 1. Confirm user name and password.
failed. 2. Check the SMTP/POP3 server.
1104 The domain the destined address 1. Confirm device's SMTP parameters.
belongs is prohibited by scanning
restriction.
1105 SMTP protocol is not enabled. 1. Confirm device's SMTP protocols.
1106 Sender’s address is not specified. 1. Confirm device's SMTP protocols.
2101 Connection to the SMTP/POP3 server 1. Check the SMTP/POP3 server name.
has failed. 2. Confirm that the LAN cable is properly connected to
the device.
3. Check the SMTP/POP3 port number.
nected.
6. Check the SMTP/POP3 server.
2102 Connection to the SMTP/POP3 server 1. Check the SMTP/POP3 server name.
has failed. 2. Check the SMTP/POP3 port number.
(Connection timeout) 3. Confirm device's network parameters.
nected.
2201 Connection to the SMTP/POP3 server 1. Confirm device's network parameters.
has failed. 2. Confirm the network parameters the device is con-
nected.
2202 Connection to the SMTP/POP3 server 1. Confirm device's network parameters.
has failed. 2. Confirm the network parameters the device is con-
(Timeout) nected.
2204 The size of scanning exceeded its limit. 1. Confirm device's network parameters.
3101 SMTP/POP3 server responded with an 1. Confirm device's network parameters.
error. 2. Confirm the network parameters the device is con-
nected.
3201 No SMTP authentication is found. 1. Check the SMTP server.
The device supports SMTP authentication services
including CRAM-MD5, DIGEST-MD5, PLAIN and
LOGIN.
1-4-108
2LK/2LN/2LM/2LC
1-4-7 Error codes

(1) Error code
Error codes are listed on the communication reports, activity report, etc. The codes consist of an error code
indication U followed by a 5-digit number. (Error codes for V34 communication errors start with an E indica-
tion, followed by five digits.)
The upper three of the five digits indicate general classification of the error and its cause, while the lower two
indicate the detailed classification. Items for which detailed classification is not necessary have 00 as the last
two digits.
Error code
UXXXXX
Detailed classification of error code

General classification of error code
Error code indication
Figure 1-4-5
1-4-109
2LK/2LN/2LM/2LC
(2) Table of general classification

Error code Description
U00000 No response or busy after the set number of redials.
U00100 Transmission was interrupted by a press of the stop/clear key.
U00200 Reception was interrupted by a press of the stop/clear key.
U00300 Recording paper on the destination unit has run out during transmission.
U004XX A connection was made but interrupted during handshake with the receiver unit (refer to
P.1-4-112 U004XX error code table).
U006XX Communication was interrupted because of a machine problem (refer to P.1-4-112
U006XX error code table).
U00700 Communication was interrupted because of a problem in the destination unit.
U008XX A page transmission error occurred in G3 mode (refer to P.1-4-112 U008XX error code
table).
U009XX A page reception error occurred in G3 mode (refer to P.1-4-112 U009XX error code
table).
U010XX Transmission in G3 mode was interrupted by a signal error (refer to P.1-4-113 U010XX
error code table).
U011XX Reception in G3 mode was interrupted by a signal error (refer to P.1-4-114 U011XX error
code table).
U01400 An invalid one-touch key was specified during communication.
U01500 A communication error occurred when calling in V.8 mode.
U01600 A communication error occurred when called in V.8 mode.
U017XX A communication error occurred before starting T.30 protocol during transmission in V.34
mode (refer to P.1-4-115 U017XX error code table).
U018XX A communication error occurred before starting T.30 protocol during reception in V.34
mode (refer to P.1-4-115 U018XX error code table).
U03000 No document was present in the destination unit when polling reception started.
U03200 In interoffice subaddress-based bulletin board reception, data was not stored in the box
specified by the destination unit.
U03300 In polling reception from a unit of our make, operation was interrupted due to a mismatch
in permit ID or telephone number. Or, in interoffice subaddress-based bulletin board
reception, operation was interrupted due to a mismatch in permit ID or telephone num-
ber.
U03400 Polling reception was interrupted because of a mismatch in individual numbers (destina-
tion unit is either of our make or by another manufacturer).
U03500 In interoffice subaddress-based bulletin board reception, the specified Subaddress confi-
dential box number was not registered in the destination unit.
U03600 An interoffice subaddress-based bulletin board reception was interrupted because of a
mismatch in the specified subaddress confidential box number.
U03700 Interoffice subaddress-based bulletin board reception failed because the destination unit
had no subaddress-based bulletin board transmission capability, or data was not stored
in any subaddress confidential box in the destination unit.
1-4-110
2LK/2LN/2LM/2LC

U04000 In interoffice subaddress-based transmission mode, the specified subaddress box num-
ber was not registered in the destination unit.
U04100 Subaddress-based transmission failed because the destination unit had no subaddress-
based reception capability.
U04200 In encrypted transmission, the specified encryption box was not registered in the desti-
nation unit.
U04300 Encrypted transmission failed because the destination unit had no encrypted communi-
cation capability.
U04400 Encrypted transmission was interrupted because encryption keys did not agree.
U04500 Encrypted reception was interrupted because of a mismatch in encryption keys.
U05100 Password check transmission or restricted transmission was interrupted because the
permit ID’s did not agree with.
U05200 Password check reception or restricted reception was interrupted because the permit
ID’s did not match, the rejected FAX number’s did match, or the destination receiver did
not return its phone number.
U05300 The password check reception or the restricted reception was interrupted because the
permitted numbers did not match, the rejected numbers did match, or the machine in
question did not acknowledge its phone number.
U14000 Memory overflowed during confidential reception. Or, in subaddress-based confidential
reception, memory overflowed.
U14100 In interoffice subaddress-based transmission, memory overflowed in the destination unit.
U19000 Memory overflowed during memory reception.
U19100 Memory overflowed in the destination unit during transmission.
U19300 Transmission failed because an error occurred during JBIG encoding.
1-4-111
2LK/2LN/2LM/2LC
(2-1) U004XX error code table: Interrupted phase B

U00430 Polling request was received but interrupted because of a mismatch in permit number.
Or, subaddress-based bulletin board transmission request was received but interrupted
because of a mismatch in permit ID in the transmitting unit.
U00431 An subaddress-based bulletin board transmission was interrupted because the specified
subaddress confidential box was not registered.
U00432 An subaddress-based bulletin board transmission was interrupted because of a mis-
match in Subaddress confidential box numbers.
U00433 Subaddress-based bulletin board transmission request was received but data was not
present in the subaddress confidential box.
U00440 Subaddress-based confidential reception was interrupted because the specified subad-
dress box was not registered.
U00450 The destination transmitter disconnected because the permit ID’s did not agree with
while the destination transmitter is in password-check transmission or restricted trans-
mission.
U00460 Encrypted reception was interrupted because the specified encryption box number was
not registered.
U00462 Encrypted reception was interrupted because the encryption key for the specified
encryption box was not registered.
(2-2) U006XX error code table: Problems with the unit

U00601 Document jam or the document length exceeds the maximum.
U00613 Image writing section problem
U00656 Data was not transmitted to a modem error.
U00690 System error.
(2-3) U008XX error code table: Page transmission error

U00800 A page transmission error occurred because of reception of a RTN or PIN signal.
U00811 A page transmission error reoccurred after retry of transmission in the ECM mode.
(2-4) U009XX error code table: Page reception error

U00900 An RTN or PIN signal was transmitted because of a page reception error.
U00910 A page reception error remained after retry of transmission in the ECM mode.
1-4-112
2LK/2LN/2LM/2LC
(2-5) U010XX error code table: G3 transmission

U01000 An FTT signal was received for a set number of times after TCF signal transmission at
2400 bps. Or, an RTN signal was received in response to a Q signal (excluding EOP)
after transmission at 2400 bps.
U01001 Function of the unit differs from that indicated by a DIS signal.
U01016 An MCF signal was received but no DIS signal was received after transmission of an
EOM signal, and T1 timeout was detected.
U01019 No relevant signal was received after transmission of a CNC signal, and the preset num-
ber of command retransfers was exceeded (between units of our make).
U01020 No relevant signal was received after transmission of a CTC signal, and the preset num-
ber of command retransfers was exceeded (ECM).
U01021 No relevant signal was received after transmission of an EOR.Q signal, and the preset
number of command retransfers was exceeded (ECM).
U01022 No relevant signal was received after transmission of an RR signal, and the preset num-
ber of command retransfers was exceeded (ECM).
U01028 T5 time-out was detected during ECM transmission (ECM).
U01052 A DCN signal was received after transmission of an RR signal (ECM).
U01080 A PIP signal was received after transmission of a PPS.NULL signal.
U01092 During transmission in V.34 mode, communication was interrupted because of an impos-
sible combination of the symbol speed and communication speed.
U01093 A DCN or other inappropriate signal was received during phase B of transmission.
U01094 The preset number of command retransfers for DCS/NSS signals was exceeded during
phase B of transmission.
U01095 No relevant signal was received after transmission of a PPS (Q) signal during phase D of
transmission, and the preset number of command transfers was exceeded.
U01096 A DCN signal or invalid command was received during phase D of transmission.
U01097 The preset number of command retransfers was exceeded after transmission of an RR
signal or no response.
1-4-113
2LK/2LN/2LM/2LC
(2-6) U011XX error code table: G3 reception

U01100 Function of the unit differs from that indicated by a DCS signal.
U01101 Function of the unit (excl. communication mode select) differs from that indicated by an
NSS signal.
U01102 A DTC (NSC) signal was received when no transmission data was in the unit.
U01110 No response after transmission of a DIS signal.
U01111 No response after transmission of a DTC (NSC) signal.
U01113 No response after transmission of an FTT signal.
U01125 No response after transmission of a CNS signal (between units of our make).
U01129 No response after transmission of an SPA signal (short protocol).
U01141 A DCN signal was received after transmission of a DTC signal.
U01143 A DCN signal was received after transmission of an FTT signal.
U01155 A DCN signal was received after transmission of an SPA signal (short protocol).
U01160 During message reception, transmission time exceeded the maximum transmission time
per line.
U01162 Reception was aborted due to a modem malfunction during message reception.
U01191 Communication was interrupted because an error occurred during an image data recep-
tion sequence in the V.34 mode.
U01193 There was no response, or a DCN signal or invalid command was received, during
phase C/D of reception.
U01194 A DCN signal was received during phase B of reception.
U01195 No message was received during phase C of reception.
U01196 Error line control was exceeded and a decoding error occurred for the message being
received.
1-4-114
2LK/2LN/2LM/2LC
(2-7) U017XX error code table: V.34 transmission

U01700 A communication error occurred in phase 2 (line probing).
U01720 A communication error occurred in phase 4 (modem parameter exchange).
U01721 Operation was interrupted due to the absence of a common communication speed
between units.
U01700: A communication error that occurs at the transmitting unit in the period after transmission of INFO0
before entering phase 3 (primary channel equivalent device training). For example, INFO0/A/Abar
(B/Bbar, for polling transmission)/INFOh was not detected.
U01720: A communication error that occurs at the transmitting unit in the period after initiating the control
channel before entering the T.30 process. For example, PPh/ALT/MPh/E was not detected.
U01721: In the absence of a common communication speed between units (including when an impossible
combination of communication speed and symbol speed occurs) after MPh exchange; 1) a DCN sig-
nal was received from the destination unit, and the line was cut; or 2) a DIS (NSF, CSI) signal was
received from the destination unit and, in response to the signal, the unit transmitted a DCN signal,
and the line was cut.
(2-8) U018XX error code table: V.34 reception

U01800 A communication error occurred in phase 2 (line probing).
U01810 A communication error occurred in phase 3 (primary channel equivalent device training).
U01820 A communication error occurred in phase 4 (modem parameter exchange).
U01821 Operation was interrupted due to the absence of a common communication speed
between units.
U01800: A communication error that occurs at the receiver unit in the period after transmission of INFO0
before entering phase 3 (primary channel equivalent device training). For example, INFO0/B/Bbar
(A/Abar, for polling reception)/probing tone was not detected.
U01810: A communication error that occurs at the receiver unit in phase 3 (primary channel equivalent device
training). For example, S/Sbar/PP/TRN was not detected.
U01820: A communication error that occurs at the receiver unit in the period after initiating the control channel
before entering the T.30 process. For example, PPh/ALT/MPh/E was not detected.
U01821: In the absence of a common communication speed between units (including when an impossible
combination of communication speed and symbol speed occurs) after MPh exchange, a DCN signal
was transmitted to the destination unit and the line was cut.
1-4-115
2LK/2LN/2LM/2LC
1-4-116
2LK/2LN/2LM/2LC
1-5-1 Precautions for assembly and disassembly

1-5 Assembly and disassembly
(1) Precautions
Before starting disassembly, press the Power key on the operation panel to off. Make sure that the Power
lamp is off before turning off the main power switch. And then unplug the power cable from the wall outlet.
When the fax kit is installed, be sure to disconnect the modular cable before starting disassembly.
When handling PWBs (printed wiring boards), do not touch parts with bare hands.
The PWBs are susceptible to static charge.
Do not touch any PWB containing ICs with bare hands or any object prone to static charge.
When removing the hook of the connector, be sure to release the hook.
Take care not to get the cables caught.
To reassemble the parts, use the original screws. If the types and the sizes of screws are not known, refer to
the PARTS LIST.
(2) Drum
Note the following when handling or storing the drum.
When removing the drum unit, never expose the drum surface to strong direct light.
Keep the drum at an ambient temperature between -20°C/-4°F and 40°C/104°F and at a relative humidity not
higher than 85% RH. Avoid abrupt changes in temperature and humidity.
Avoid exposure to any substance which is harmful to or may affect the quality of the drum.
Do not touch the drum surface with any object. Should it be touched by hands or stained with oil, clean it.
(3) Toner
Store the toner container in a cool, dark place.
Avoid direct light and high humidity.
1-5-1
2LK/2LN/2LM/2LC
(4) How to tell a genuine Kyocera Mita toner container
As a means of brand protection, the Kyocera Mita toner container utilizes an optical security technology to
enable visual validation. A validation viewer is required to accomplish this.
Hold the validation viewer over the left side part of the brand protection seal on the toner container. Through
each window of the validation viewer, the left side part of the seal should be seen as follows:
A black-colored band when seen through the left side window ( )

A shiny or gold-colored band when seen through the right side window ( )
The above will reveal that the toner container is a genuine Kyocera Mita branded toner container, otherwise, it
is a counterfeit.
See through the left window See through the right window
( marking) ( marking)
Validation viewer Validation viewer
Brand Brand
protection protection
seal seal
A black-colored band when A shiny or gold-colored band when

seen through the left side window seen through the right side window
Figure 1-5-1
The brand protection seal has an incision as shown below to prohibit reuse.
Incision
Cut
Figure 1-5-2
1-5-2
2LK/2LN/2LM/2LC
1-5-2 Paper feed section

(1) Detaching and refitting the primary paper feed unit
Procedure
Remove the primary paper feed unit
1. Pull the cassette 1 and cassette 2 out
completely.
2. Pull the conveying unit out.
3. Open the right lower cover.
4. Remove the strap and then remove the
right lower cover.
Strap
Conveying unit
Right lower cover
Figure 1-5-3
1-5-3
2LK/2LN/2LM/2LC
Right middle
5. Remove the rear upper cover and the rear cover
rear lower cover (see page 1-5-65).
6. Remove two screws A and then remove
the right middle rear cover.
7. Remove three screws B and then
remove the right lower rear cover.
Screws A
Right lower
rear cover
Screws B
Figure 1-5-4
8. Open the handle cover. Right lower

9. Remove three screws. front cover
10. Unhook the hook and then remove the
right lower front cover.
Hook
Screws
Right lower Handle cover

front cover
Screw
Figure 1-5-5
1-5-4
2LK/2LN/2LM/2LC
11. Remove two connectors.
Connector
Connector
Figure 1-5-6
12. Remove two screws each from primary [45ppm/55ppm] Primary paper
feed unit
paper feed unit.
13. Remove the primary paper feed unit.
*: Use the specific primary paper feed unit
depending on model - 30 ppm/35 ppm or
Screws
45 ppm/55 ppm.
Screws
Primary paper
feed unit [30ppm/35ppm]
Primary paper
feed unit
Primary paper
feed unit
Figure 1-5-7
1-5-5
2LK/2LN/2LM/2LC
[45ppm/55ppm] Driving
14. Check or replace the primary paper coupler
feed unit and refit all the removed parts. Pin
*: When refit the primary paper feed unit, you
must confirm the inserted pin to the driving Pin
coupler.
*: For 45ppm/55ppm model, you must install Driving coupler
the primary paper feed unit while pushing
Primary paper
the retard release lever of the lower side, feed unit
when the primary paper feed unit is refitted
[30ppm/35ppm]
(see page 1-5-10).
Pin
Driving coupler
Primary paper
feed unit
Primary paper
feed unit
Primary paper
feed unit
Retard release lever
Primary paper
feed unit (lower side)
[45ppm/55ppm]
Figure 1-5-8
1-5-6
2LK/2LN/2LM/2LC
(2) Detaching and refitting the forwarding pulley, paper feed pulley and separation
pulley. [30 ppm model / 35 ppm model]
Procedure
1. Remove the primary paper feed unit
(see page 1-5-3).
Detaching the forward pulley and paper

Stop ring
feed pulley
2. Remove four stop rings.
Stop rings
Stop ring
Primary paper
feed unit
Figure 1-5-9
3. Slide the paper feed pulley shaft. Forwarding pulley Spring

4. Remove the joint and three bushes. holder assembly
5. Remove the spring and forwarding pul-
ley holder assembly.
Bush
Bush
Joint
Bush
Paper feed pulley shaft
Figure 1-5-10
1-5-7
2LK/2LN/2LM/2LC
6. Pull the primary paper feed shaft out

from the forwarding pulley holder. Paper feed pulley Paper feed pulley
7. Remove the feed gear Z30H OW and
paper feed pulley. Feed gear Feed gear
Z30H OW Z30H OW
*: To refit the feed gear Z30H OW, be sure
to correctly align it with the paper feed
pulley, so that the on-way clutches meet
each other.
Oneway
clutch
Primary paper feed shaft
Forwarding
pulley holder
Figure 1-5-11
8. Pull the forwarding pulley from the axis Forwarding pulley

hole of forwarding pulley holder.
Gear
Axis hole
Axis hole
Forwarding pulley holder
Figure 1-5-12
1-5-8
2LK/2LN/2LM/2LC
Detaching the separation pulley

9. Remove the spring.
10. Remove the retard holder from the pri-
mary lower plate.
Spring
Hole
Hole
Primary lower plate
Retard holder
Figure 1-5-13
11. Remove the separation pulley from the Separation pulley

retard holder.
12. Clean or replace the forwarding pulley,
paper feed pulley and separation pulley.
13. Refit the forwarding pulley, paper feed
pulley and separation pulley to the pri-
mary paper feed unit.
14. When the forwarding pulley, paper feed
pulley or separation pulley is replaced,
Axis hole
perform maintenance mode U903
(clearing the jam counter) (see page 1-
3-181).
Retard holder
Axis hole
Figure 1-5-14
1-5-9
2LK/2LN/2LM/2LC
(3) Detaching and refitting the forwarding pulley, paper feed pulley and separation
pulley. [45 ppm model / 55 ppm model]
Procedure
1. Remove the primary paper feed unit
(see page 1-5-3).
Paper feed pulley
Detaching the forward pulley and paper
Feed gear
feed pulley Z30R OW Oneway clutch
2. Remove the stop ring A and then
remove the one way clutch and the
Stop ring A
paper feed pulley.
3. Remove the stop ring B and then
remove the forwarding pulley.
Primary paper
feed unit Forwarding pulley
Stop ring B
Pickup gear
Z30R
Figure 1-5-15
4. Remove the stop ring. Torque limiter

5. Remove the separation pulley while Separation pulley
push the retard release lever.
6. Clean or replace the forwarding pulley, Stop ring
paper feed pulley, separation pulley.
7. Refit the forwarding pulley, paper feed
pulley, separation pulley to the primary
paper feed unit.
8. When the forwarding pulley, paper feed
pulley or separation pulley is replaced,
perform maintenance mode U903 Retard
(clearing the jam counter) (see page 1- release lever
3-181).
Figure 1-5-16
1-5-10
2LK/2LN/2LM/2LC
(4) Detaching and refitting the MP tray paper feed unit
Procedure
2. Open the MP tray.
3. Remove four screws. Screw
Screw
Conveying unit
MP tray
Figure 1-5-17
4. Unhook seven hooks and then remove Right cover

the DU cover assembly.
Hooks
Hook
Hooks
DU cover
assembly Right cover
Figure 1-5-18
1-5-11
2LK/2LN/2LM/2LC
5. Remove two connectors. Connector

6. Release the wire saddle.
7. Remove the wire saddle.
*: To refit the wire saddle, be sure to fit in the
positioning hole that was previously used.
Wire
saddle
Connector
Installation
hole
Wire
saddle
Figure 1-5-19
8. Remove the MP tray.

*: When refitting the MP tray, insert it in the
MP tray paper feed unit side by turning the
lift arm.
MP tray
Lift arm
MP tray paper feed unit MP tray
Figure 1-5-20
1-5-12
2LK/2LN/2LM/2LC
9. Remove two screws.

10. Remove the MP tray paper feed unit.
Screw
MP tray
paper feed unit
Screw
MP tray
paper feed unit
Figure 1-5-21
1-5-13
2LK/2LN/2LM/2LC
(5) Detaching and refitting the MP forwarding pulley, MP paper feed pulley and MP
separation pulley
Procedure
1. Remove the MP tray paper feed unit DU lower guide
(see page 1-5-11).
Detaching forwarding pulley and paper

feed pulley
2. Unhook three hooks and then remove
Hooks
the Du lower guide.
*: Remove the DU lower guide easy by
bending the top base that the hook is
hooking because the hook of the DU Hook
lower guide lacks flexibility.
MP tray
paper feed unit
Top base
Figure 1-5-22
3. Remove the stop ring A and then slide Stop ring A

Driving joint
the driving joint.
4. Slide the bush A.
5. Remove the stop ring B and then Bush A
remove the bush B.
Bush B
Stop ring B
Figure 1-5-23
1-5-14
2LK/2LN/2LM/2LC
6. Unhook the hook of the feed holder Spring

assembly.
7. Remove the spring and the feed holder Hook
assembly from the top base.
Feed holder assembly
Top base
Top base
Spring
Hook
Figure 1-5-24
Oneway gear MP paper feed pulley

8. Remove the two stop ring.
Z30R
9. Pull the feed MPF shaft out. Oneway gear Stop ring
10. Remove the two bushes, one way gear Z30R
Z30R and MP paper feed pulley.
*: To refit the one-way gear Z30R, mount the
gear in the correct direction as shown.
Oneway
clutch Bush
Bush
Stop ring
Feed MFP shaft
Figure 1-5-25
1-5-15
2LK/2LN/2LM/2LC
11. Remove the pickup MPF shaft from the Pickup MFP shaft
axis holes of feed MPF holder.
12. Pull the pickup gear Z30R and MP for- MP forwarding pulley
warding pulley out from the pickup MFP
shaft. Pickup gear Z30R
Feed gear Z26H
Axis hole
Feed MPF holder

Axis hole
Figure 1-5-26
Detaching the MP separation pulley

13. Unhook two hooks and then remove the
middle guide.
Hook
Hook
Middle guide
Figure 1-5-27
1-5-16
2LK/2LN/2LM/2LC
14. Remove the spring.

15. Release the uniting of joint by sliding
the retard holder assembly.
Joint
Retard holder
assembly
Spring
Figure 1-5-28
16. Remove the retard holder assembly by

turning it as shown.
Retard holder
assembly
Figure 1-5-29
1-5-17
2LK/2LN/2LM/2LC
17. Remove two stop rings. Retard MPF shaft

18. Remove two bushes.
19. Pull the retard MPF shaft out and then
remove the torque limiter and the MP Torque limiter
separation pulley. MP separation
20. Clean or replace the MP forwarding pul- pulley
ley, MP paper feed pulley and MP sepa-
ration pulley.
21. Refit the MP forwarding pulley, MP
paper feed pulley and MP separation Bush
pulley to the MP tray paper feed unit.
22. When the MP forwarding pulley, MP
paper feed pulley or MP separation pul-
ley is replaced, perform maintenance
mode U903 (clearing the jam counter)
(see page 1-3-181). Stop ring
Retard holder
Bush
Stop ring
Figure 1-5-30
1-5-18
2LK/2LN/2LM/2LC
1-5-3 Optical section

(1) Detaching and refitting the exposure lamp
Notes on handling the LED mount assembly

Do not touch the diffusion seat and the light guid-
LED mount assembly Diffusion seat
ing plate.
Light guiding
Use air blow when you clean the diffusion seat,
plate
the light guiding plate, and reflector.
Do not clean it using a cleaning cloth that
Reflector
adheres the fiber easily.
LED PWB
White LED
Diffusion seat
Figure 1-5-31
Procedure
1. Remove the original cover or the docu- ISU front cover
ISU right cover
ment processor.
Screws
2. Remove two screws and then remove Screws
the ISU front cover.
3. Remove two screws and then remove
the ISU right cover.
Figure 1-5-32
1-5-19
2LK/2LN/2LM/2LC

Screw ISU rear cover
the ISU rear cover.
Screw
Figure 1-5-33
5. Remove the platen.

6. Peels two films off. Platen
Film Film
Film Film
Figure 1-5-34
1-5-20
2LK/2LN/2LM/2LC
7. Move the LED mount assembly to the LED mount assembly

Cutting lack part
cutting lack part.
8. Unhook the hook and remove the FFC
cover from LED mount assembly.
9. Remove the FFC from the FFC connec-
tor.
10. Unhook two hooks and remove the FFC
guide from the LED mount assembly.
Cutting lack part
FFC cover
Hook
Hook
FFC
FFC connector
LED mount assembly

FFC guide Hook
Figure 1-5-35
11. Remove two screws and then remove Screw

the LED mount assembly.
12. Check or replace the LED mount
assembly and refit all the removed
parts. LED mount assembly
*: When cleaning the reflector, the light guid- Screw

ing plate and the diffusion sheet of the
LED mount assembly, clean it by air blow.
Not to leave the hair dust.
13. When the LED mount assembly is

replaced, perform maintenance mode
U411 (Adjusting the scanner automati-
cally) (see page 1-3-153).
Figure 1-5-36
1-5-21
2LK/2LN/2LM/2LC
(2) Detaching and refitting the ISU
Procedure
Detaching the ISU
1. Worn the electrostatic prevention band Screws
Screw
for the destruction prevention of the ISU
circuit board by static electricity. Lens cover
2. Remove the platen (see page 1-5-19).
3. Remove six screws and then remove Screw
the lens cover.
ISU PWB
Figure 1-5-37
4. Remove the connector.

tor with a lock.
*: When removing the FFC from the FFC
connector with a lock, remove it after FFC connector
FFC with a lock
release the lock by lifting the lock lever
up (see page 1-5-50).
Connector
Figure 1-5-38
1-5-22
2LK/2LN/2LM/2LC
6. Remove four screws and then remove [45ppm/55ppm]

the ISU.
*: The ISU's are different depending on
30ppm model/35ppm model and 45ppm
model/55ppm model. Screw Screw
Screw
Screw
ISU
[30ppm/35ppm]
Screw Screw
Screw
Screw
ISU
Figure 1-5-39
1-5-23
2LK/2LN/2LM/2LC
Refitting the ISU

7. Decide the fix position of ISU by the fol- [45ppm/55ppm]
lowing.
The right and left of machine:
Confirm the number (a) of seal pasted
on lens.
Match the line (c) of ISU to the position-
ing line (b) of same number on frame
side.
c
The rear and front of machine:
Match the edge (e) of ISU to the posi- b
tioning line (d) on frame side.
8. Fix the ISU as before with four screws. Lens
9. Refit all the removed parts.
a
d
ISU
[30ppm/35ppm]
c
Lens
b
a
d ISU
Figure 1-5-40
1-5-24
2LK/2LN/2LM/2LC
(3) Detaching and refitting the LSU
Procedure
1. Remove the conveying unit (see page
1-5-39). Transfer belt filters
2. Remove the left upper cover (see page
1-5-49).
3. Remove the toner filter.
4. Remove the left filter cover and the left
filter.
5. Remove two transfer belt filters.
6. Remove the left cover lid. Screw A
7. Open the front cover and remove screw
A.
8. Remove three screws B and then
remove the left cover. Screws B
Toner filter
Screw B
Left cover
Left cover lid
Left filter cover
Left filter
Figure 1-5-41
9. Remove four screws and then remove

the LSU retainer.
Screws
LSU retainer
Screws
Figure 1-5-42
1-5-25
2LK/2LN/2LM/2LC

the middle feed plate.
11. Remove two LSU retainer pins and two
springs.
Spring
LSU retainer pin
Screw
Middle feed plate

Screw
Figure 1-5-43
12. Pull the LSU out a little.

13. Remove the following connector from
the LSU.
30 ppm model/35 ppm model:
FFC connector with a lock: 1pcs
Connector: 2pcs
45 ppm model/55 ppm model:

FFC connector with a lock: 2pcs
Connector: 2pcs LSU
*: When remove the FFC from the FFC con- *:45ppm/55ppm only
nector with a lock, removing it after release
the lock by lifting the lock lever up.
Connectors
FFC connector
with a lock
FFC
FFC connector *
with a lock
FFC
Figure 1-5-44
1-5-26
2LK/2LN/2LM/2LC
14. Pull the LSU out from the body of the

machine.
LSU
Figure 1-5-45
15. Remove seven screws and then

remove the LSU mount lid. Screws
Screws
Screws
LSU mount lid

Screw
Figure 1-5-46
1-5-27
2LK/2LN/2LM/2LC
16. Remove the screw.

17. Unhook four hooks and then remove
the LSU relay PWB cover.
Screw
Hooks
LSU relay PWB cover

Hooks
Figure 1-5-47
18. Remove all the connectors and the FFC

connectors with a lock.
(30ppm model/35ppm model has the
FFC connector without a lock.)
*: When remove the FFC from the FFC con-
nector with a lock, removing it after
release the lock by lifting the lock lever up.
19. Remove the electric wire from the elec-
tric wire support portion.
20. Remove the FFC from the FFC support
potion.
FFC support portions

Electric wire
support portion
FFC
Connector
FFC connector *
with a lock
*: 30ppm/35ppm is FFC connector without the lock.
Figure 1-5-48
1-5-28
2LK/2LN/2LM/2LC
21. Remove the LSU retainer pins and the

springs.
22. Remove two screws each and then
remove the LSU front holder.
Screw
Spring LSU front holder

LSU retainer pin Screw
Figure 1-5-49
1-5-29
2LK/2LN/2LM/2LC
23. Wrap an antistatic discharging belt LSU (rear side) LSU (front side)
around your wrist to prevent damage to Support
portion
the LSU.
*: Do not touch terminals and FFC contacts
in the LSU APC board.
24. Remove four LSUs, following the pre-
cautions and instructions below.
(1) Lift the far end of the LSU.
(2) Unhook the protrusions at the front
of the LSU.
Support portion
*: Be sure to handle the front and rear
handholds when handling the LSU. LSU(Y)
*: Do not get the LSU in direct contact with
the holding frame subsequently applying
shocks to the polygon motor inside.
25. Check or replace the LSU and refit all

the removed parts.
*: When reconnecting FFCs, be sure to
insert the FFC all the way in with the FFC
connector.This is to avoid a lengthy ser-
vicing due to a possible error which could LSU(Y)
cause re-disassembly and -assembly.
LSU(C)
26. When replacing the new LSU, proceed LSU(M)
as follows: LSU(K)
1)Performs maintenance mode U469
(Auto color registration correction)
(see page 1-3-175). LSU support frame
(Adjusting the halftone automatically) LSU (rear side) LSU (front side)
(see page 1-3-151).
(1) (2)
Bos
LSU(C)
LSU(M)
LSU(K)
Figure 1-5-50
1-5-30
2LK/2LN/2LM/2LC
(4) Color registration adjustment

Follow the procedure below to replace the laser scanner unit.
Procedure
2. Press [Adjustment/Maintenance], [Calibration] and then [Start]. Calibration begins.
Auto correction
3. Press [Color Registration], [Auto] and then [Start]. A chart is printed.
4. Place the printed chart as the original and then [Start]. Color registration begins.
Figure 1-5-51
Manual correction
5. Press [Color Registration], [Manual], [Chart] and then [Ptint]. A chart is printed.
6. Press [Registration].
Read figures at MH-1 to 7/CH-1 to 7/YH-1 to 7 and MV-3/CV-3/YV-3 of the reference chart and
enter the figure marked at the scale which the BK fine line is in line with the M/C/Y fine lines,
using the +/- keys.
7. Press [Start] after all values have been entered. Color registration begins.
(example)
When a red bar exactly coincides
Chart for adjustment with B, enter B as a value.
Figure 1-5-52
1-5-31
2LK/2LN/2LM/2LC
8. Press [Chart] and [Print] to print a

chart.
9. Verify that each scale is within the
range of 1to A. If they are within the
range, proceed to step 10.
If scales are out of range, repeat steps
6 through 9.
The scale must be corresponding

within the range of "A" from "1".
Figure 1-5-53
10. Verify that scales of MV-1,2,4,5/CV-

1,2,4,5/YV-1,2,4,5 coincide within the
range of 1 to A.
If they are within the range, adjustment
is complete.
If they are out of range, proceed to step
11.
Figure 1-5-54
If manual color registration has failed:

11. If the balance between V-1 and V-5 is
more than 2 scales (sample 1) or less
than -2
scales (sample 2), perform the following
steps:
Sample 1 Sample 2
V-1 V-2 V-3 V-4 V-5 V-1 V-2 V-3 V-4 V-5
Figure 1-5-55
1-5-32
2LK/2LN/2LM/2LC
12. Open the front cover and then pull out the waste toner box tray (see page 1-5-34).
13. Rotate the adjustment knob using a 5 mm hex wrench.
Direction of rotation
(V-1 - V-5) >= 2 scales (sample 1): rotate counterclockwise.
(V-1 - V-5) <= -2 scales (sample 2): rotate clockwise.
Number of rotation
(V-1- V-5) x 4 clicks
14. Refit the waste toner box tray as before and then close the front cover.
15. Turn the main power switch off and on. Correction automatically starts.
16. Print a reference chart and verify the result.
Hexagon socket
Allen wrench
Hexagon socket Hexagon socket Hexagon socket
Figure 1-5-56
1-5-33
2LK/2LN/2LM/2LC
1-5-4 Image formation section

(1) Detaching and refitting the inner unit
Procedure
2. Remove all toner container each.
3. Detach the waste toner box tray while
pushing up the hook of both ends.
Hook Waste toner

box tray
Hook
Figure 1-5-57
4. Remove the screw and then open the

connector cover. Inner unit
6. Remove four fixed screw of inner unit. Connector cover
Screw
Inner unit Connector
Screw
Screw Screw
Screw
Figure 1-5-58
1-5-34
2LK/2LN/2LM/2LC
7. Release the lock by pushing the fixed

lever at the right and left of inner unit. Inner unit
8. Remove the inner unit.
Fixed lever
Figure 1-5-59
1-5-35
2LK/2LN/2LM/2LC
(2) Detaching and refitting the developer unit and drum unit
Detaching example: Developer unit Y and Drum unit Y

Connectors
Procedure
1. Remove the fuser unit (see page 1-5-
45).
2. Pull the transfer belt unit out a little (see
page 1-5-41). Toner supply shutter
3. Remove the inner unit (see page 1-5-
34).
4. Close the toner supply shutter.
Developer unit
Figure 1-5-60
6. Pull out as one body the developer unit

and the drum unit.
(The developer unit becomes basic and
the drum units are combined.)
7. Detach the developer unit while sup-
Developer unit
porting bottom.
Drum unit
Drum unit
Developer unit
Figure 1-5-61
1-5-36
2LK/2LN/2LM/2LC
8. Remove the drum unit from the devel-

oper unit.
9. Check or replace the drum unit and the Drum unit
developer unit and refit all the removed
parts.
10. When replacing the new developer unit,

proceed as follows:
1) Performs maintenance mode U140
(AC calibration) for 45 ppm/55 ppm
model only (see page 1-3-91).
(Calibration) (see page 1-3-168).
(see page 1-3-175).
4)Performs maintenance mode U410 Developer unit
(Adjusting the halftone automatically)
(see page 1-3-151).
Figure 1-5-62
11. When replacing the new drum unit, pro-
ceed as follows:
(drum setup) (see page 1-3-83).
(AC calibration) for 45 ppm/55 ppm
model only (see page 1-3-91).
(see page 1-3-175).
(see page 1-3-151).
1-5-37
2LK/2LN/2LM/2LC
(3) Detaching and refitting the charger roller unit

Detaching example: Charger roller unit Y
Procedure
1. Remove the inner unit (see page 1-5-
34).
2. Pull out the charger roller unit by pick-
ing and releasing the MC lock lever.
3. Check or replace the charger roller unit
and refit all the removed parts.
*: When refitting the charger roller unit, that

must hook the hook certain by operating
the MC lock lever after inserting the char-
ger roller unit until bumping.
4. When replacing the new charger roller Charger roller unit

unit, proceed as follows:
Performs maintenance mode U930
(clearing the charger roller count) (see
page 1-3-190). Hook
MC lock lever
Figure 1-5-63
1-5-38
2LK/2LN/2LM/2LC
1-5-5 Transfer section

(1) Detaching and refitting the conveying unit
Procedure
2. Remove three screws. Conveying unit
3. Unhook three hooks and then remove Right front cover
the right front cover.
Screw
Hook
Hook
Hook
Right front Screw

cover
? 1?5?64

conveying inner cover from the convey-
ing unit.
Conveying unit
Hook
Hook
Conveying inner cover
Figure 1-5-65
1-5-39
2LK/2LN/2LM/2LC
5. Remove four screws.

6. Remove the conveying unit by lifting Conveying unit
upward.
Screws Screws
Conveying
unit
Figure 1-5-66
1-5-40
2LK/2LN/2LM/2LC
(2) Detaching and refitting the transfer belt unit
Procedure
1. Remove the conveying unit (see page
1-5-39).
45).
Connector
Figure 1-5-67
4. Pull out the transfer belt unit by lifting up

both ends.
Transfer belt unit
Figure 1-5-68
1-5-41
2LK/2LN/2LM/2LC
5. Remove the transfer belt unit.

6. Check or replace the transfer belt unit
Transfer belt unit
*: When refitting the new transfer belt
unit, set the projected part aligned with
the rail entrance.
7. When replacing the new transfer belt

unit, proceed as follows:
(Transfer belt speed correction) (see
page 1-3-175).
(see page 1-3-175).
(see page 1-3-151).
Transfer belt unit
Rail entrance
Projection
Rail entrance part
Projection
part
Transfer belt unit Transfer belt unit
Figure 1-5-69
1-5-42
2LK/2LN/2LM/2LC
(3) Detaching and reffiting the transfer roller
Procedure
1. Pull out the conveying unit.
Conveying unit
Figure 1-5-70
2. Loosen two fixed screws on the TC Transfer roller (shaft)

guide. Bearing
Bearing Stop ring
3. Remove the stop ring.
4. Unhook the hook and remove the TC
gear Z29R.
5. Remove two bearings.
6. Remove the transfer roller.
TC gear Z29R Transfer roller (shaft)
Hook
Transfer roller
TC guide
Screw
TC guide
TC guide Screw
Figure 1-5-71
1-5-43
2LK/2LN/2LM/2LC
7. Check or replace the transfer roller and

refit all the removed parts.
*: When refitting the transfer roller, confirm
that the terminal of the ground plate is in
contact with the ground plate in the frame.
8. When replacing the new transfer roller,

proceed as follows:
(clearing the transfer counter) (see
page 1-3-85).
(Calibration) (see page 1-3-168). Ground plate
(see page 1-3-175).
(see page 1-3-151).
Ground plate Ground plate
(terminal) (frame)
Figure 1-5-72
1-5-44
2LK/2LN/2LM/2LC
1-5-6 Fuser section

(1) Detaching and reffiting the fuser unit
Procedure
1. Pull out the conveying unit.
2. Remove the screw and then the fuser
electric wire cover.
3. Remove two connectors
Connector Connector
Fuser electric wire cover
Screw
Conveying unit
Figure 1-5-73
1-5-45
2LK/2LN/2LM/2LC
4. Remove four screws (M4 × 10) and

then remove the fuser unit.
5. Check or replace the fuser unit and refit
all the removed parts. Fuser unit
6. When replacing the new fuser unit, pro- Screws

ceed as follows: (M4×10)
(clearing the fuser count) (see page
1-3-100).
(see page 1-3-175).
(see page 1-3-151). Screws
(M4×10)
Figure 1-5-74
1-5-46
2LK/2LN/2LM/2LC
(2) Detaching and reffiting Fuser IH unit
Procedure
1. Remove the rear upper cover and the Fuser IH PWB
45).
3. Remove the right upper cover (see
page 1-5-65).
4. Remove the right middle rear cover
(see page 1-5-65).
the fuser IH PWB cover (see page 1-5-
65).
6. Remove the IH electric wire cover (see
page 1-5-65).
7. Remove the electric wire holder.
9. Remove two connectors from the fuser
Electric wire holder Wire saddle Connector
IH PWB according to the following
notes.
*: Confirm the power plug is removed from
the outlet without fail when you remove
the connector because a high current is
supplied to fuser IH unit by this connec-
tor.
*: Confirm the connected connector was
surely locked when you connect this con-
nector again. Fuser IH PWB
Figure 1-5-75
1-5-47
2LK/2LN/2LM/2LC

11. Unhook the hook by lifting up the fuser
IH unit a little and then remove it.
Fuser IH unit
Screw
Screw
Hook
Hook
Fuser IH unit
Figure 1-5-76
1-5-48
2LK/2LN/2LM/2LC
1-5-7 PWBs
(1) Detaching and refitting the main PWB
Procedure
1. Remove the rear upper cover (see page
1-5-65).
2. Open the controller lid.
4. Unhook six hooks and then remove the
left upper cover.
Left upper
cover
Controller lid Screws
Hooks
Hook
Left upper cover
Hooks
Figure 1-5-77
Electric wire holder
5. Release six wire saddles on the control- Wire saddle Wire saddles
ler box.
6. Remove the electric wire holder.
Controller box
Wire saddle
Wire saddle
Figure 1-5-78
1-5-49
2LK/2LN/2LM/2LC
7. Remove the following connectors that

connected to the main PWB from the
outside of the control box.
YC25
YC11
YC30
YC24
YC3 (FFC connector with a lock)
YC17 (BK) Controller box
YC21 (WH) Main PWB
YC12
YC12
YC25 YC17YC21
*: When removing the FFC from the FFC YC11
connector with a lock, remove the FFC YC30
after released by lifting up the lock lever
(see figure a and b).
*: When connecting the FFC that there is a
projection in the terminal both sides, lock
by knocking down the lock lever after
inserting the FFC to the connector until YC24
both projections are hidden
(see figure c). YC3
Main PWB FFC connector with a lock
a [State of lock] [Lock release/FFC detaching]
FFC
1
2
Lock lever Lock lever
b [State of lock] [Lock release/FFC detaching]

Lock lever 1
Lock lever
2
FFC
c [FFC connection/Lock] Projection

2
Lock lever
Projection FFC
Figure 1-5-79
1-5-50
2LK/2LN/2LM/2LC
8. Remove five screws.

controller box.
Controller box
Hook
Hook
Screws
Screw Screws
Figure 1-5-80
Main PWB
10. Remove the following connectors that
connected to the main PWB.
YC23
YC27
YC32
YC9
YC1 [BLACK] (with a lock)
YC2 [BLUE] (with a lock)
YC23
*: When removing the FFC from the FFC YC27

connector with a lock, remove the FFC YC32
(see page 1-5-50)
YC1
BLACK
YC9
YC2
YC8
BLUE
FFC connector with a lock
Main PWB
Controller box
Figure 1-5-81
1-5-51
2LK/2LN/2LM/2LC
11. Release the wire saddle. Electric

12. Remove two electric wire holders. wire holder
13. Remove two screws. Fan mootor holder Screws
14. Remove the fan motor holder.
Controller box
Wire saddle
Figure 1-5-82
15. Remove five screws from the main

PWB. Screws Main PWB
Screws
Screw
Main PWB
Figure 1-5-83
1-5-52
2LK/2LN/2LM/2LC
16. Remove the main PWB by releasing the

projection of ground plate in the net-
work connector.
*: Check or replace the main PWB and refit Network connector
all the removed parts.
*: When replacing the main PWB, remove

the following devices from the main PWB
and then reattach it to the new main PWB.
EEPROM (YC14) Projections

for ground
Code DIMM (YS4) Network connector
Memory DDR (YS1)
*: Exchange EEPROM (YC14) and code Main PWB

DIMM (YC4) by the set.
Main PWB
BK
WH
Code DIMM Memory

(YS4) DDR
YS4
(YS1)
YS1
BLACK EEPROM
YC14
BLUE
(YC14)
Figure 1-5-84
1-5-53
2LK/2LN/2LM/2LC
(2) Detaching and refitting the engine PWB

Procedure
1. Remove the controller box (see page 1-
5-49).
2. Remove twenty three connectors of fol-
lowing from the engine PWB.
YC1
YC2
YC3
YC4
YC6 (FFC connector with a lock) Engine PWB
YC26
YC9 FFC connector with a lock
YC8
YC2
YC5
YC4
YC1
YC15
YC7
YC6 YC27
YC16
YC18 YC3
YC17
YC26
YC19
YC10
YC20
YC21
YC22
YC45

connector with a lock, remove the FFC
YC9

(see page 1-5-50)
YC45
YC8
YC22
YC21
YC20
YC46
YC19
YC17
YC12 YC15 YC16

YC18
Engine PWB
Figure 1-5-85
1-5-54
2LK/2LN/2LM/2LC
3. Remove six screws.

engine PWB. Hook
Hook
5. Check or replace the engine PWB and
refit all the removed parts. Engine PWB
Engine PWB
*: When replacing the engine PWB,

remove the EEPROM (U100) from the
engine PWB and then reattach it to the
new engine PWB.
Screws
Screws Engine PWB
Screws
Engine PWB
U100
EEPROM
(U100)
Figure 1-5-86
1-5-55
2LK/2LN/2LM/2LC
(3) Detaching and refitting the power source PWB
Procedure
Connector
1. Remove the rear under cover (see page
1-5-65).
2. Release three wire saddles. Connector
3. Remove four connectors.
Connectors
Wire saddle
Wire saddle
Waire saddle
Figure 1-5-87
4. Release six wire saddles.

Wire saddle
5. Remove the following eleven connec-
tors and three tabs from the power Power source assembly
source PWB.
YC3
YC1
TB1
TB2
TB5
YC7 Wire saddles
YC8
YC17 Wire
YC14 saddles
YC12
YC16
YC13
YC10
YC11 Power source PWB
YC17 YC14 YC12 YC16 YC13YC10 YC11

YC3
YC1
TB5
TB1 TB2
YC7
YC8
Power source PWB
Figure 1-5-88
1-5-56
2LK/2LN/2LM/2LC

7. Remove the connector from the coin
vender plate.
Connctor
Wire saddle
Coin vender
plate
Figure 1-5-89

9. Remove the power source assembly.
Screw
Screw
Power source assembly
Figure 1-5-90
1-5-57
2LK/2LN/2LM/2LC
10. Remove eight screws. Screws

11. Remove the power source PWB.
12. Check or replace the power source Screws
PWB and refit all the removed parts. Screws
Power source PWB

Screw
Figure 1-5-91
1-5-58
2LK/2LN/2LM/2LC
(4) Detaching and refitting the high voltage PWB 1
Procedure
1. Remove the power source PWB (see
page 1-5-56).
2. Remove the main drive unit (see page
1-5-73).
3. Remove five connectors from high volt-
age PWB.
High voltage
PWB 1
Connectors
YC4
YC18 Connectors
YC3
YC10
YC11
High voltage
PWB 1
Connector
Figure 1-5-92
4. Remove eight screws.

5. Unhook two hooks of PWB spacer and
then remove the high voltage PWB 1.
6. Check or replace the high voltage PWB
1 and refit all the removed parts.
Screws
Screw
Screws
Screw
PWB spacer
Screws High voltage PWB 1
Figure 1-5-93
1-5-59
2LK/2LN/2LM/2LC
(5) Detaching and refitting the high voltage PWB 2
Procedure
1. Remove the main drive unit (see page
1-5-73).
2. Pull the transfer belt unit out a little (see
page 1-5-41).
3. Remove two connectors from the high
voltage PWB 2 assembly.
High voltage
PWB 2 assembly
Connectors High voltage

PWB 2 assembly
Figure 1-5-94

high voltage PWB 2.
6. Check or replace the high voltage PWB
2 and refit all the removed parts.
Hook
Hook
Screws
High voltage
PWB 2 assembly
Figure 1-5-95
1-5-60
2LK/2LN/2LM/2LC
(6) Detaching and refitting the operation PWB
Procedure
1. Pull the conveying unit out. Right upper cover
2. Remove the screw from the right upper
cover.
Screw
Figure 1-5-96

4. Remove the screw and then remove the
fan cover.
5. Unhook three hooks and then remove
Hooks
the front upper right cover.
Front upper
right cover
Fan cover
Screw
Figure 1-5-97
1-5-61
2LK/2LN/2LM/2LC
6. Remove the screw and then remove the Screw

operation panel cover.
Operation panel cover
Operation panel cover
Figure 1-5-98

the USB electric wire (connector).
Screws
USB electric wire

(connector)
Figure 1-5-99
1-5-62
2LK/2LN/2LM/2LC
8. Remove four screws.
Screws
Screws
Figure 1-5-100
9. Pull the operation panel unit upward.

10. Release three wire saddles. Operation panel unit
11. Remove four connectors from the oper-
ation PWB.
12. Remove the operation panel unit.
Operation PWB
Connectors
Connector
Wire saddle
Operation
panel unit
Connector
Waire saddles
Figure 1-5-101
1-5-63
2LK/2LN/2LM/2LC
13. Remove four connectors and two FFC FFC

from the operation PWB. Operation PWB
FFC connector
*: When removing the FFC from the FFC with a lock
(see page 1-5-50). Connectors
FFC
Connectors
Figure 1-5-102

the operation PWB. Operation PWB
Screws
15. Check or replace the operation PWB
Screw
Screw
Figure 1-5-103
1-5-64
2LK/2LN/2LM/2LC
(7) Detaching and refitting the fuser IH PWB
Procedure
1. Remove seven screws and then
remove the rear upper cover.
Rear upper cover
Screws
Screws
Screws
Screw
Figure 1-5-104
2. Remove eight screws.

3. Release two hanging parts and then
remove the rear lower cover. Screw
45).
Screw
Screws
Rear lower cover
Screws
Figure 1-5-105
1-5-65
2LK/2LN/2LM/2LC

Screws
the ISU right cover.
6. Remove the screw and five hooks and ISU right
then remove the right upper cover. cover
Right upper cover
Screw
Figure 1-5-106
7. Remove two screws. Right middle rear cover

right middle rear cover.
Screws
Figure 1-5-107
1-5-66
2LK/2LN/2LM/2LC
9. Remove four screws and the remove

IH electric wire cover
the fuser IH PWB cover.
10. Remove the IH electric wire cover.
Screw
Screws
Screw
Fuser IH PWB cover
Figure 1-5-108
11. Release two wire saddles.

12. Remove four connector from the fuser
IH PWB.
Wire saddle
Connector
Connectors
Fuser IH PWB
Connector
Wire saddle
Figure 1-5-109
1-5-67
2LK/2LN/2LM/2LC
13. Remove two electric wire holders.

14. Remove the connector (YC27) from
feed PWB 1.
Connector
(YC27)
Feed PWB 1
Electric
wire holder
Electric
wire holder
Figure 1-5-110
15. Remove three screws.

16. Unhook two hooks and then remove IH
box assembly. IH box assembly
Screw
Hook
Hook Screws
IH box assembly
Figure 1-5-111
1-5-68
2LK/2LN/2LM/2LC
17. Remove two connectors. Screws

18. Remove six screws.
19. Unhook the hook of the PWB spacer
and then fuser IH PWB.
Screws
20. Check or replace the fuser IH PWB and
refit all the removed parts. Connector
Screws
Connector
Fuser IH PWB
PWB spacer
IH box assembly
Figure 1-5-112
1-5-69
2LK/2LN/2LM/2LC
1-5-8 Drive section

(1) Detaching and refitting the drum drive unit K and the drum drive unit MCY
Procedure
Detaching the drum drive unit K
1. Remove the rear upper cover and the
Connector
Wire saddle
Figure 1-5-113

5. Remove the drum drive unit K. Screw
*: Do not have a shaft part alone when you
carry drum drive unit K. (Have the hous-
ing.)
*: Put support on the tip of the shaft so that
Screws
the shaft may become the horizontal
when you put drum drive unit K on the
table etc.
Screw
(Shaft portion)
Screws
Drum drive unit K

(housing portion)
Figure 1-5-114
1-5-70
2LK/2LN/2LM/2LC
Detaching the drum drive unit MCY
6. Remove the left upper cover (see page Connector

1-5-49).
7. Remove the left cover (see page 1-5-
25).
9. Remove the screw. Screw
Figure 1-5-115
10. Remove as one body the toner unit

duct, the toner fan motor 1 and the
toner fan motor 2.
Screw
Toner fan
motor 2
Screw
Toner fan motor 1 Toner unit duct
Figure 1-5-116
1-5-71
2LK/2LN/2LM/2LC
11. Release two wire saddles.

12. Remove three connector.
Connector
Wire saddle
Connector
Wire saddle
Connector
Figure 1-5-117
13. Remove five screws and then remove

the drum drive unit MCY.
*: Do not have a shaft part alone when you
carry drum drive unit MCY. (Have the (Shaft portion)
housing.)
*: Put support on the tip of the shaft so that
the shaft may become the horizontal
when you put drum drive unit CMY on the
table etc.
14. Check or replace the drum drive unit K
and the drum drive unit MCY and refit (Shaft portion)
Drum drive
unit MCY
(housing portion)
Screw Screw
Screw Screws
Figure 1-5-118
1-5-72
2LK/2LN/2LM/2LC
(2) Detaching and refitting the main drive unit
Procedure
1. Remove the drum drive unit K and the
drum drive unit MCY (see page 1-5-70).
2. Release three wire saddles on the main
drive unit.
Main drive unit
Connector
Wire saddle Connector
Main drive unit
Wire saddles
Figure 1-5-119
4. Remove five screws.

5. Remove the main drive unit.
6. Check or replace the main drive unit
Main drive unit
Screw
Screw
Screw
Screw Screw
Figure 1-5-120
1-5-73
2LK/2LN/2LM/2LC
(3) Detaching and refitting the fuser drive unit, transfer drive unit and feed drive unit
Procedure
Detaching the fuser drive unit Feed PWB 1
assembly
1. Remove the rear upper cover and the
2. Remove five electric wire holders of
feed PWB 1 assembly.
Feed PWB 1
assembly
Electric
wire holder
Wire saddle
Electric
wire holder
Figure 1-5-121
4. Remove the following twenty connec-

YC19
YC20
tors from the feed PWB 1. YC3
YC18
YC18, YC19 Feed PWB 1

YC20, YC27 YC27 YC26
YC1
YC26, YC3
YC17, YC14
YC17
YC10, YC16
YC13, YC12
YC2
YC23, YC25 FFC connector

YC15, YC11 with a lock
YC5, YC4
YC14
YC16

YC10

YC4
*: When removing the FFC from the FFC con- YC23

YC12
nector with a lock, remove the FFC after

YC13
released by lifting up the lock lever (see YC25
page 1-5-50).
YC11 YC5
YC15
Figure 1-5-122
1-5-74
2LK/2LN/2LM/2LC

tor with a lock (YC4) on the engine
PWB. Engine PWB
Remove the FFC from the FFC connec-
tor with a lock (YC1) on the feed PWB FFC connector
2. with a lock (YC4)

after released by lifting up the lock lever FFC
(see page 1-5-50).
FFC connector
with a lock (YC1)
Feed PWB 2
Figure 1-5-123

7. Remove the feed PWB 1 assembly. Feed PWB 1 assembly
Screw
Screw
Screw
Screw
Screw
Screw
Feed PWB 1 assembly
Figure 1-5-124
1-5-75
2LK/2LN/2LM/2LC

10. Remove the fuser drive unit.
Fuser drive unit
Screw Fuser drive unit
Connector
Screw Screw
Figure 1-5-125
Detaching the transfer drive unit

11. Pull out the transfer belt unit a little (see
page 1-5-41).
12. Release the clamp.
13. Remove the connector. Transfer drive unit
15. Remove the transfer drive unit.
Transfer drive unit Transfer drive unit

Screw
Screw
Clamp
Connector
Clamp
Screws
Connector Screws
[45ppm/55ppm] [30ppm/35ppm]
Figure 1-5-126
1-5-76
2LK/2LN/2LM/2LC
Detaching the feed drive unit

16. Remove three electric wires from the
feed 2 FFC guide.
Electric wire
holder
Feed 2
Electric wire
holders FFC guide
Figure 1-5-127

the feed 2 FFC guide.
Feed 2
FFC guide
Screw
Screw
Screw
Feed 2
FFC guide
Screw
Figure 1-5-128
1-5-77
2LK/2LN/2LM/2LC
18. Remove the following nine connectors

from the feed PWB 2. Feed PWB 2
YC10
YC11
YC7
YC8 YC11
YC10
YC3
YC5
YC6
YC7
YC13
YC12
YC3
YC8
YC13
Feed PWB 2
YC5
YC6
YC12
Figure 1-5-129

20. Remove the feed drive unit. Feed drive unit
Screw Screw
Screw Screw
Screw Screw
Screw Screw
Screw Screw
Screw Screw
[45ppm/55ppm] [30ppm/35ppm]
Figure 1-5-130
1-5-78
2LK/2LN/2LM/2LC
21. Check or replace the feed drive unit and

refit all the removed parts.
*: Connect the connector (yellow) to the con-
Feed drive unit
nector of paper feed clutch 1 on stamp
[YELLOW] side as before, when removing
the connector of the paper feed clutch as
the check of the feed drive unit etc.
Paper feed
clutch 1
Marking
[YELLOW]
Connector
Connector
(Yellow)
Paper feed clutch 2
Figure 1-5-131
1-5-79
2LK/2LN/2LM/2LC
(4) Detaching and refitting the lift motor 1 and 2
Procedure
1. Remove the rear lower cover (see page
1-5-65).
2. Remove the power source assembly
(see page 1-5-56).
3. Remove the connector each.
4. Remove two screws each.
5. Remove the lift motor 1 and 2.
6. Check or replace the lift motor and refit Lift motor 1
Lift motor 2
Lift motor
Connector
Screws
Figure 1-5-132
1-5-80
2LK/2LN/2LM/2LC
1-5-9 Others
(1) Detaching the eject filter
Procedure
1. Unhook the hook and remove the eject
filter units. Eject filter units Eject filter
2. Remove the eject filters from the eject
covers.
3. Check or replace the eject filters and
refit the filter.
Hook
Hook
Eject cover
Figure 1-5-133
1-5-81
2LK/2LN/2LM/2LC
(2) Detaching and refitting the toner filter
Procedure
1. Remove the toner filter unit while grip-
ping the levers. Toner
2. Check or replace the toner filter unit filter unit
and refit the filter.
Levers
Toner
filter unit
Figure 1-5-134
1-5-82
2LK/2LN/2LM/2LC
(3) Detaching and refitting the fan filter
Procedure
2. Remove the fan filter by releasing the
lever.
3. Clean the fan filter.
4. Refit the fan filter.
Front cover
Fan filter
Lever Fan filter
Figure 1-5-135
1-5-83
2LK/2LN/2LM/2LC
(4) Detaching and refitting the transfer belt filter
Procedure
1. Remove two transfer belt filters by Lever
releasing the lever.
2. Clean the transfer belt filter. Transfer belt filter
3. Refit the transfer belt filter. Lever
Transfer belt filters
Figure 1-5-136
1-5-84
2LK/2LN/2LM/2LC
(5) Detaching and refitting the DU filter
Procedure
1. Open the MP tray.
2. Remove two DU filters by releasing the
DU filter
lever.
3. Clean the DU filter. DU filter
4. Refit the DU filter.
Lever
Lever
DU filter
MP tray
Figure 1-5-137
1-5-85
2LK/2LN/2LM/2LC
(6) Detaching and refitting the left filter
Procedure
1. Remove the left filter cover by releasing
the lever.
2. Remove the left filter. Left filter
3. Check or replace the left filter and refit
the filter. Lever
Left filter
cover
Figure 1-5-138
1-5-86
2LK/2LN/2LM/2LC
(7) Detaching and refitting the hard disk unit
Procedure
1. Perform maintenance mode U917
(backup data reading) (see page 1-3-
186).
2. Remove the rear upper cover (see page
1-5-65).
Screws
Wire saddle
Figure 1-5-139
5. Unhook two hooks and pull out the

HDD bracket a little. Hook
Hook
HDD bracket
Figure 1-5-140
1-5-87
2LK/2LN/2LM/2LC
6. Remove two connectors from the hard [30ppm/35ppm] [45ppm/55ppm]

disk unit while pushing the lock lever.
Number of hard disk unit equipment Hard disk
30ppm model/35ppm model: 1 unit
45ppm model/55ppm model: 2
Hard disk
unit Hard disk
unit
Lever Lever
Connector
Connector
Figure 1-5-141
7. Remove four screws and then remove Screw

HDD bracket
the hard disk unit from the HDD Screw
bracket.
8. Replace the hard disk unit and refit all
Screw
the removed parts.
(HDD formatting) (see page 1-3-29).
Screw
2. Install the firmwares by the following
procedure.
1)Connects to the machine the USB Screw
memory that preserved Software
LANGUAGE BR, JP (Opt Font,Opt
Msg), and the PDF1.7 resource.
The firmware is installed by switching Hard disk unit
the main power switch to ON/OFF. (45ppm/55ppm only)
2)Connects to the machine the USB
memory that preserved Weekly-
Timer, FMU application.
Installs the firmware from the applica-
tion screen of the system menu.
(Refer to operation guide.)
Hard disk unit
(backup data writing) (see page 1-3-
186).
Figure 1-5-142
1-5-88
2LK/2LN/2LM/2LC
(8) Direction of installing the principal fan motors

When detaching or refitting the fan motors, be careful of the airflow direction (intake or exhaust).
Fuse rear
fan motor
Eject fan
Developer motor 2
fan motor 2 Eject front
fan motor Fuser fan
LSU motor 2
fan motor Eject fan
motor 1
IH fan motor
Developer Coil fan motor1

fan motor 1
Fuser front
fan motor
Fuse fan motor 1
Eject rear fan motor

(Rating label:outside)
Fuser fan motor 1

Coil fan motor 2 (Rating label:inside)
Belt fan motor 1
(Rating label:inside)
Eject fan motor 1
Controller fan motor (Rating label:inside)
Toner fan Eject fan motor 2

motor 2 (Rating label:inside)
Belt fan motor 2 Fuser fan motor 2

Toner fan motor 1 (Rating label:inside) (Rating label:inside)
Power source fan motor

(Rating label:inside)
Figure 1-5-143
1-5-89
2LK/2LN/2LM/2LC
1-6-1 Upgrading the firmware

1-6 Requirements on PWB Replacement
Follow the procedure below to upgrade the firmware of main PWB, operation PWB, engine PWB, ISC PWB,
fuser IH PWB, motor control PWB, optional language, color table and optional devices.
Preparation
Extract the file that has the download firmware and put them in the USB Memory.
Procedure
1. Perform maintenance item U000 (main-
tenance report output) and check U019
ROM version.
2. Press the power key on the operation
panel, and after verifying the power
indicator has gone off, switch off the
main power switch. And then unplug the
power cable from the wall outlet.
3. Insert the USB memory in which the
firmware has been written into a notch
hole of the machine.
4. Insert the power plug and turn the main
power switch on. Upgrading firmware
starts (blinking the memory LED).
Caution:
Never turn the main power switch off
during upgrading. USB memory
5. [Completed] is displayed on the touch
panel when upgrading is complete.
Figure 1-6-1
6. Press the power key on the operation
panel, and after verifying the power
indicator has gone off, switch off the
main power switch. And then unplug the
power cable from the wall outlet.
7. Wait for several seconds and then
remove the USB memory from the
machine.
8. Insert the power plug and turn the main
power switch on.
9. Perform maintenance item U000 (main-
tenance report output) and check that
U019 ROM version has been upgraded.
1-6-1
2LK/2LN/2LM/2LC
1-6-2 Remarks on main PWB replacement

When replacing the main PWB, remove the EEPROM (YC14) and code DIMM (YS4) from the main PWB that
has been removed and then reattach it to the new main PWB.
Main PWB
EEPROM
YC14
Figure 1-6-2
When refitting DIMM, check "CODE" and "FLS" marked on the PWB and refit them to the original positions.
Main PWB
YS4
CODE FLS
YS3
DIMM
Figure 1-6-3
1-6-2
2LK/2LN/2LM/2LC
When connecting the hard disk cables (YC1, YC2) to the PWB, match "BLACK" and "BLUE" marked on the
PWB with the connector colors.
Main PWB
YC1
BLACK
YC2
BLUE
Figure 1-6-4
When connecting the USB cables (YC17, YC21) to the PWB, match "BK" and "WH" marked on the PWB with
the connector colors.
Main PWB
WH
BK
YC17 YC21
Figure 1-6-5
1-6-3
2LK/2LN/2LM/2LC
1-6-3 Remarks on engine PWB replacement

When replacing the engine PWB, remove the EEPROM (U100) from the engine PWB that has been removed
and then reattach it to the new engine PWB.
Engine PWB
EEPROM
U100
Figure 1-6-6
1-6-4
2LK/2LN/2LM/2LC
2-1-1 Paper feed/conveying section

2-1 Mechanical Construction
Paper feed/conveying section consists of the paper feed unit that feeds paper from the cassette and the MP
tray paper feed unit that feeds paper from the MP tray, and the paper conveying section that conveys the fed
paper to the transfer/separation section.
(1) Cassette paper feed section

Cassette paper feed section consists of the paper holder with the cassette operation plate activated by lift
motor 1 and 2, and the pulleys, such as the forwarding pulley, the paper feed pulley and the separation pulley,
for extracting and conveying the paper. Paper is fed out of the cassette by the rotation of the forwarding pulley,
paper feed pulley and separation pulley.
11 7
5 21
4
1 13
8
6 10
17 23
2
3 15 9
12
4 5 22
24
7
16
1 14
8
20 6
2
3 18
10
9
19
Figure 2-1-1 Cassette paper feed section
1. Cassette base 12. Paper sensor 2 (PS2) 19. Paper gauge sensor 2 (L)
2. Cassette operation plate 13. Lift sensor 1 (LS1) (PGS2(L))
3. Cassette 14. Lift sensor 2 (LS2) 20. Actuator
4. Forwarding pulleys 15. Paper gauge sensor 1 (U) (Paper gauge sensor 2)
5. Paper feed pulleys (PGS1(U)) 21. Feed sensor 1 (FS1)
6. Separation pulleys 16. Paper gauge sensor 1 (L) 22. Feed sensor 2 (FS2)
7. Assist rollers* (PGS1(L)) 23. Paper conveying sensor
8. Assist pulleys* 17. Actuator (PCS)
9. Paper conveying roller (Paper gauge sensor 1) 24. Actuator
10. Paper conveying pulley 18. Paper gauge sensor 2 (U) (Paper conveying sensor)
11. Paper sensor 1 (PS1) (PGS2(U)) *: 45 ppm/55 ppm model only
2-1-1
2LK/2LN/2LM/2LC
FEED_MOT_DIR
YC2-2 6
FEED_MOT_RDY
YC2-3 5
FEED_MOT_CLK PFM
YC2-4 4
FEED_MOT_REM 3
YC2-5
ASIST_CL1
YC10-1
FEED_CL1_REM ASCL1*
YC4-1 PFCL1
CAS1_P0_SENS
YC8-11
PICK_SOL1_REM
YC8-2 FS1
PICK_SOL1_RET PUSOL1*
YC8-3
CAS1_EMPTY_SENS PS1
YC8-6
CAS1_LIFT_UP_SENS
YC8-9 LS1
LIFT_MOT1_RET PCCL
YC3-13
LIFT_MOT1_DR LM1
YC3-14
PCS
CAS1_QUANT1 PGS1(U)
YC3-19
CAS1_QUANT2 PGS1(L)
YC3-22 ASCL2*
PFCL2
CAS2_P0_SENS
YC8-23
PICK_SOL2_REM
YC8-14 FS2
PICK_SOL2_RET PUSOL2*
YC8-15
CAS2_EMPTY_SENS PS2
YC8-18
CAS2_LIFT_UP_SENS
YC8-21 LS2
LIFT_MOT2_RET
YC3-15
LIFT_MOT2_DR LM2
YC3-16
CAS2_QUANT1 PGS2(U)
YC3-25
CAS2_QUANT2 PGS2(L)
YC3-28
FEED_CL2_REM
YC4-3
ASIST_CL2
YC12-1
FEED2_SENS
YC6-3
V-FEED_CL_REM
YC5-3
FPWB2
YC1 YC4 EPWB
Figure 2-1-2 Cassette paper feed section block diagram
2-1-2
2LK/2LN/2LM/2LC
(2) MP tray paper feed section

Paper is fed out of the MP tray by the rotation of the MP forwarding pulley, MP paper feed pulley and MP sep-
aration pulley. The MP separation pulley prevents multiple sheets from being fed at one time by the torque lim-
iter.
2 7
1
12 14 5
3 4 11
6
15
10 13
Figure 2-1-3 MP tray paper feed section
1. MP forwarding pulley 10. MP paper length switch

2. MP paper feed pulley (MPPLSW)
3. MP separate pulley 11. Actuator
4. MP table (MP paper length switch)
5. MP support Tray 12. MP paper width switch
6. MP paper sensor (MPPS) (MPPWSW)
7. Actuator (MP paper sensor) 13. MP tray switch (MPTSW)
8. MP lift sensor 1 (MPLS1) 14. MP feed sensor (MPFS)
9. MP lift sensor 2 (MPLS2)
2-1-3
2LK/2LN/2LM/2LC
RYPWB
MPF_LIFT_UP_SENS MPLS1
YC3-5
MPF_PPR_SET MPPS
YC3-3
MPF_CL_REM MP
YC3-13 PFCL
MPF_LIFT_DOWN_SENS MPLS2 MPPLSW MPTSW

YC3-8
MPPWSW
MPF_JAM_SENS MPFS
YC3-11
MPF_LIFT_DR_B
YC3-11
YC3-11 MPF_LIFT_DR_A MPLM
MPF_WID1
YC2-7
MPF_WID2
YC2-5
MPF_WID3
YC2-4
MPF_LNG
YC2-2
MPF_TABLE
YC2-9
YC12 YC17 YC1 YC6

FPWB1 EPWB
Figure 2-1-4 MP tray paper feed section block diagram
2-1-4
2LK/2LN/2LM/2LC
(3) Paper conveying section

The paper conveying section conveys paper to the transfer/separation section as paper feeding from the cas-
sette or MP tray, or as paper refeeding for duplex printing. Paper by feeding is conveyed by the middle roller to
the position where the registration sensor (RS) is turned on, and then sent to the transfer/separation section
by the right registration roller and left registration roller.
4
3
9
8 2
Figure 2-1-5 Paper conveying section
1. Middle roller 6. Middle sensor (MS)

2. Middle pulley 7. Regist deflection sensor (RDS)
3. Left registration roller 8. Actuator
4. Right registration roller (regist deflection sensor)
5. Paper conveying pulley 9. Registration sensor (RS)
2-1-5
2LK/2LN/2LM/2LC
FPWB2
REG_CL_REM
RCL YC22-2
REG_SENS
YC7-12 RS
BEND_SENS RDS
YC7-5
FFED1_SENS FPWB1
YC8-9 MS
MID_CL_REM MCL
YC7-14
FEED_MOT_DIR
YC2-2 6
FEED_MOT_RDY
YC2-3 5
FEED_MOT_CLK PFM
YC2-4 4
FEED_MOT_REM 3
YC2-5
YC1 YC4 YC5-42 YC2-9

EPWB
Figure 2-1-6 Paper conveying section block diagram (30 ppm/35 ppm model)
2-1-6
2LK/2LN/2LM/2LC
REG_MOT_B/
FPWB2 YC25-1
REG_MOT_A/
YC25-2
RM REG_MOT_B
YC25-3
REG_MOT_A
YC25-4
REG_SENS
YC7-12 RS
BEND_SENS RDS
YC7-5
FFED1_SENS
YC8-9 MS FPWB1
MID_B/
YC7-1
MID_A/
YC7-2
MID_B MM
YC7-3
MID_A
YC7-4
FEED_MOT_DIR
YC2-2 6
FEED_MOT_RDY
YC2-3 5
FEED_MOT_CLK PFM
YC2-4 4
FEED_MOT_REM 3
YC2-5
YC1 YC4 YC5-42 YC2-9

EPWB
Figure 2-1-7 Paper conveying section block diagram (45 ppm/55 ppm model)
2-1-7
2LK/2LN/2LM/2LC
2-1-2 Drum section

The drum section consists of the charger roller unit, drum and cleaning section. The drum is electrically
charged uniformly by means of a charger roller to form a latent image on the surface. The cleaning section
consists of the cleaning blade and the cleaning roller which remove residual toner from the drum surface after
transfer. The cleaning lamp (CL) consists of LEDs and removes residual charge on the drum before main
charging.
10
7
1
9
3
Figure 2-1-8 Drum section
1. Drum 6. Cleaning blade

2. Charger roller 7. Cleaning roller
3. Charger cleaning roller 8. Control roller
4. Charger case 9. Drum screw
5. Drum frame 10. Cleaning lamp (CL)
2-1-8
Main chager
START high voltage Y
/STOP EEP_SCL
6 YC4-14
CLOCK YC14-2
5 YC4-16 EEP_SDA
LD YC14-3
EEPROM
DRPWB-Y
4 YC4-18
DRM-Y
Drum
unit Y
CW/CCW
3 YC4-20
CL-Y
ERS_Y_REM
YC14-8
YC10 YC2 Main chager

START high voltage C
/STOP EEP_SCL
6 YC4-13
CLOCK YC12-2
5 YC4-15 EEP_SDA
[45 ppm/55 ppm model only]

LD YC12-3
EEPROM
DRPWB-C
4 YC4-17
DRM-C
Drum
CW/CCW
unit C
3 YC4-19
CL-C
ERS_C_REM
YC12-8
2-1-9
EPWB
HVPWB1
Main chager
FRPWB
MCPWB
START high voltage M
/STOP EEP_SCL
6 YC5-14
CLOCK YC10-2
5 YC5-16 EEP_SDA
LD YC10-3
EEPROM
DRM
DRPWB-M
4 YC5-18
-MCY*1
DRM-M*2
Drum
CW/CCW
unit M
3 YC5-20
Figure 2-1-9 Drum section block diagram

CL-M
ERS_M_REM
YC10-8
YC3 YC9
*2: 45 ppm/55 ppm model

*1: 30 ppm/35 ppm model
Main chager
START high voltage K
/STOP EEP_SCL
6 YC5-13
CLOCK YC7-2
5 YC5-15 EEP_SDA
LD YC7-3
EEPROM
DRPWB-K
4 YC5-17
DRM-K
Drum
CW/CCW
unit K
3 YC5-19
CL-K
ERS_K_REM
YC7-8
2LK/2LN/2LM/2LC
2LK/2LN/2LM/2LC
2-1-3 Developer section

The developer unit consists of the sleeve roller that forms the magnetic brush, the magnet roller, the devel-
oper blade and the developer screws that agitate the toner. Also, the toner sensor (TS) checks whether or not
toner remains in the developer unit.
1 1
2 2
8
6 8
6
5 5
3
3
4
4
7
9 7
9
[30 ppm/35 ppm model] [45 ppm/55 ppm model]
Figure 2-1-10 Developer section
1. Sleeve roller 6. Developer case

2. Magnet roller 7. Developer cover
3. Developer screw A 8. Magnet cover
4. Developer screw B 9. Toner sensor (TS)
5. Developer blade
2-1-10
YC15-1 TPD_TEMP
YC15-2 VCONT
YC15-3 TPD_Y
TN_CLK
unit Y
YC15-4
TS-Y
YC15-8 EEP_SDA Magnet bias Y
Developer
YC15-9 EEP_SCL
Sleeve bias Y
YC15-12 VIB_MOT
VM-Y
YC10 YC2
YC13-1 TPD_TEMP
START VCONT
/STOP YC13-2
6 YC7-2 YC13-3 TPD_C
CLOCK
5 YC7-3 TN_CLK
unit C
YC13-4
TS-C
LD EEP_SDA
4 YC7-4 YC13-8 Magnet bias C
Developer
CW/CCW
DRM-MCY
3 YC7-5 YC13-9 EEP_SCL
Sleeve bias C
YC13-12 VIB_MOT
VM-C
EPWB
TPD_TEMP
FRPWB
MCPWB
YC11-1
HVPWB
2-1-11
YC11-2 VCONT
YC11-3 TPD_M
YC11-4 TN_CLK
unit M
TS-M
YC11-8 EEP_SDA Magnet bias M
Developer
YC11-9 EEP_SCL
YC3 YC9 Sleeve bias M
YC11-12 VIB_MOT
Figure 2-1-11 Developer section block diagram

VM-M
YC9-1 TPD_TEMP
YC9-2 VCONT
START
/STOP YC9-3 TPD_K
6 YC7-9
TN_CLK
unit K
CLOCK YC9-4
TS-K
5 YC7-10 EEP_SDA
LD YC9-8 Magnet bias K
Developer
4 YC7-11 EEP_SCL
DEVM-K
CW/CCW YC9-9
3 YC7-12 Sleeve bias K
YC9-12 VIB_MOT
VM-K
2LK/2LN/2LM/2LC
2LK/2LN/2LM/2LC
2-1-4 Optical section

The optical section consists of the image scanner section for scanning and the laser scanner section for print-
ing.
(1) Image scanner section

The original image is illuminated by the exposure lamp (EL) and scanned by the CCD image sensor in the
CCD PWB (CCDPWB) via the three mirrors and ISU lens, the reflected light being converted to an electrical
signal.
The mirror frame A and B travel to scan on the optical rails on the front and rear of the machine to scan from
side to side. The speed of the mirror frame B is half the speed of the mirror frame A.
6 12 13 4 3 11 9 15
6 2 14 5 1 7 8 10
Figure 2-1-12 Image scanner section
1. Mirror frame A 9. ISU cover

2. Mirror frame B 10. Scanner wire drum
3. LED mount 11. Contact glass
4. Scanner reflector 12. Slit glass
5. Mirror A 13. Original size indicator plate
6. Mirror B 14. Home position sensor (HPS)
7. ISU lens 15. Original detection switch
8. CCD PWB (CCDPWB) (ODSW)
2-1-12
unit
Image
scanner
HP_SW
YC8-3
HPS
SDA
YC6-3
SCL
YC6-4
VSET
YC6-5
POW
LEDPWB
YC6-9
ORG_SW
YC13-2 OSS
Lens
2-1-13
MPWB
ISCPWB
Reading
image data
Original
YC9 YC2
YC11 YC3
CCD
image
CCDPWB
sensor
YC25 YC4
Figure 2-1-13 Image scanner section block diagram

SMOT_AP
YC5-1
SMOT_BP
YC5-2
SMOT_AN
SM
YC5-3
SMOT_BN
YC5-4
CO_SW
YC14-3
ODSW
2LK/2LN/2LM/2LC
2LK/2LN/2LM/2LC
(2) Laser scanner section

The charged surface of the drum is then scanned by the laser beam from the laser scanner unit. The laser
beam is dispersed as the polygon motor (PM) revolves to reflect the laser beam over the drum. Various lenses
and mirror are housed in the laser scanner unit, adjust the diameter of the laser beam, and focalize it at the
drum surface. Also the LSU cleaning motor (LSUCM) is activated to conduct automatically cleaning of the
LSU dust shield glass.
8
5 7
2 1
Figure 2-1-14 Laser scanner section
1. Polygon motor (PM) 5. f-θ lens B

2. f-θ lens A 6. Mirror C
3. Mirror A 7. LSU dust shield glass
4. Mirror B 8. LSU spiral
2-1-14
2LK/2LN/2LM/2LC
YC5-2 BD_Bk YC1-29 TH

LSU_TH_Bk BD PDPWB-K
YC5-3 YC1-28
LDD_CS_Bk
YC5-9 YC1-22
DATA_1N_Bk APC
YC5-25 YC1-6 Laser
DATA_1P_Bk PWB-K
YC5-26 YC1-5 scanner
DATA_2N_Bk unit K
YC5-28 YC1-3
DATA_2P_Bk YC1-2
YC5-29
REM_Bk
YC4-3 3
LOCK_Bk PM-K
YC4-4 2
CLK_Bk
YC4-5 1
YC8-2 BD_M YC1-29 TH

LSU_TH_M BD PDPWB-M
YC8-3 YC1-28
LDD_CS_M
YC8-9 YC1-22
DATA_1N_M APC
YC8-25 YC1-6 Laser
DATA_1P_M PWB-M
DATA_2N_M unit M
YC8-28 YC1-3
DATA_2P_M YC1-2
YC8-29
REM_M
YC7-3 3
LOCK_M PM-M
YC7-4 2
CLK_M
YC7-5 1
LSURPWB
YC10-2 BD_C YC1-29 TH
LSU_TH_C BD PDPWB-C
YC10-3 YC1-28
LDD_CS_C
YC10-9 YC1-22
DATA_1N_C APC
YC10-25 YC1-6 Laser
DATA_1P_C PWB-C
DATA_2N_C unit C
YC10-28 YC1-3
DATA_2P_C YC1-2
YC10-29
REM_C
YC9-3 3
LOCK_C PM-C
YC9-4 2
CLK_C
YC9-5 1
YC12-2 BD_Y YC1-29 TH

LSU_TH_Y BD PDPWB-Y
YC12-3 YC1-28
LDD_CS_Y
YC12-9 YC1-22
DATA_1N_Y APC
YC12-25 YC1-6 Laser
DATA_1P_Y PWB-Y
DATA_2N_Y unit Y
YC12-28 YC1-3
DATA_2P_Y YC1-2
YC12-29
REM_Y
YC11-3 3
LOCK_Y PM-Y
YC11-4 2
CLK_Y
YC11-5 1
DR_CCW
YC2 YC11 YC21-1 LSU
EPWB DR_CW
YC3 YC12 YC21-2 CM
Figure 2-1-15 Laser scanner unit block diagram
2-1-15
2LK/2LN/2LM/2LC
2-1-5 Transfer/Separation section

The transfer/separation section consists of the intermediate transfer unit section and the secondary transfer
roller section.
(1) Intermediate transfer unit section

The intermediate transfer unit section consists of the transfer cleaning unit, the transfer belt, and the four pri-
mary transfer rollers for respective color drums, and forms a full-color toner image by superimposing and
transferring single-color toner images formed on each drum onto the transfer belt. Also with the ID sensors
(IDS) mounted on the machine frame, the toner density on the transfer belt is measured.
The transfer cleaning unit collects toner remaining on the transfer belt after secondary transfer and forwards it
as waste toner to the waste toner box.
16
17 7 10 11 13 15 8 1
18
19
20
2 6 5 4 2 3 14 12 9 2
Figure 2-1-16 Intermediate transfer unit section
1. Drive roller 11. Color release sensor (CRS)

2. Backup roller 12. Transfer belt sensor (TRBLS)
3. Primary transfer roller K 13. Transfer skew sensor (TRSS)
4. Primary transfer roller M 14. Transfer edge sensor (TRES)
5. Primary transfer roller C 15. Transfer edge motor (TREM)
6. Primary transfer roller Y 16. Cleaning pre brush
7. Tension roller 17. Cleaning fur brush
8. Transfer belt 18. Cleaning roller
9. ID sensor (IDS) 19. Cleaning blade
10. Color release motor (CRM) 20. Cleaning screw
2-1-16
2LK/2LN/2LM/2LC
HVPWB2
Primary transfer bias Y
Primary transfer bias C
Primary transfer bias M
Primary transfer bias K

Cleaning bias
Transfer
belt unit
DCS
DES
CRS
TRPWB
TRBLS
TRCM CRM DCM
ZIG_REV_SENS
3
4
5
6
ZIG_DR_CCW
BELT_SPEED
ZIG_DR_CW
RLS_SENS
ZIG_SENS
EEP_SDA
EEP_SCL
ICL_REM
ICL_RDY
ICL_CLK
RLS_DR
ICL_DIR
YC3-A3
YC3-A4
YC3-A5
YC3-A6
YC3-A7
YC3-A12
YC3-A13
YC3-A10
YC3-B2
YC3-B12
YC3-B13
YC3-B5
YC3-B8
EPWB
YC6
YC5
YC1
YC2
YC10-6 REG_SENS_F_P
YC10-7 REG_SENS_F_S IDS1
YC10-11 REG_SENS_R_P
YC10-12 REG_SENS_R_S IDS2
YC10-14 CLN_SOL_REM
FPWB1 YC10-15 CLN_SOL_RET CLSOL
TR_BRK
YC13-1 7
TR_DIR
YC13-2 6
TR_RDY TRM
YC13-3 5
TR_CLK
YC13-4 4
TR_REM
YC13-5 3
Figure 2-1-17 Intermediate transfer unit section block diagram
2-1-17
2LK/2LN/2LM/2LC
(2) Secondary transfer roller section

The secondary transfer roller section consists of the secondary transfer roller mounted to the paper conveying
unit and the separation brush. To the secondary transfer roller, DC bias is applied from the high voltage PWB
2 (HVPWB2). The toner image formed on the transfer belt is transferred to the paper by the potential differ-
ence and the paper is separated by curvature separation.
5
1
6
Figure 2-1-18 Secondary transfer roller section
1. Secondary transfer roller

2. Separation brush
3. Secondary transfer frame
4. Transfer guide
5. Transfer release sensor (TRRS)
6. Transfer release motor (TRRM)
2-1-18
2LK/2LN/2LM/2LC
EPWB
HVPWB2
Separation brush
Separation bias SP_REM
YC1-7 YC8-5
Secondary transfer bias T2_REM
YC1-8 YC8-6
TRRS
Secondary
transfer roller
TRRM
PRS_REM1
PRS_REM2
PRS_SENS
FPWB1
YC-14-4
YC-14-5
YC-14-2
PRS_REM1
YC1-16 YC6-49
PRS_REM2
YC1-15 YC6-50
PRS_SENS
YC1-14 YC6-51
RYPWB YC1 YC14
Figure 2-1-19 Secondary transfer roller section block diagram
2-1-19
2LK/2LN/2LM/2LC
2-1-6 Fuser section

The paper sent from the transfer/separation section is interleaved between the heat roller and the press roller.
The heat roller (fuser belt) is heated by the fuser IH (FIH), and the toner is fused by heat and pressure and
fixed onto the paper because the press roller is pressed by the fuser press spring. The surface temperature of
heat roller and press roller are detected by the fuser thermistor (FTH) and controlled by the engine PWB
(EPWB).
9 16 8
3
6 15
5
7
3 13
4 2
1
14
11 12
10
Figure 2-1-20 Fuser section
1. Heat roller (Fuser belt) 9. Fuser eject pulley

2. Press roller 10. Loop sensor (LPS)
3. IH coils 11. Fuser belt sensor (FUBLS)
4. Side core 12. Fuser thermistor 1 (FTH1)
5. Arch core 13. Fuser thermistor 2 (FTH2)
6. Separators 14. Fuser thermistor 3 (FTH3)
7. Right fuser cover 15. Fuser thermistor 4 (FTH4)
8. Fuser eject roller
2-1-20
2LK/2LN/2LM/2LC
PRESS_TH
YC26-B9
FSR_SIZE_SENS FUES
YC26-A13
FSR_RLS_DR_CW
YC26-A11
FSR_RLS_DR_CCW FURM
YC26-A12
FSR_RLS_SENS Fuser unit
YC26-A16
FURS
Y5 COIL_LIVE FTH4
EPWB
FIHPWB
COIL_COM
Y6
YC26 YC4
YC6-1 +15V1
+15V2 FTS
YC6-2
FTH2
FTH3 FTH1
MAIN_TH1,2
GUIDE_TH
EDGE_TH
FSR_BLT_PLS FUBLS
YC26-A19
YC5-1
YC3-2,3
YC4-1
MAIN_TH1,2
YC26-B16,17 YC1-5,6
GUIDE_TH
YC26-B15 YC1-7
EDGE_TH YC1-9 FUPWB
YC26-B11
FPWB1
YC6-21 CW/CCW YC1-44 YC18-2 6

YC6-20 LD YC1-45 YC18-3 5
CLOCK FUM
YC6-19 YC1-46 YC18-4 4
YC6-18 START/STOP YC1-47 YC18-5 3
Figure 2-1-21 Fuser section block diagram
2-1-21
2LK/2LN/2LM/2LC
2-1-7 Eject/Feedshift section

The paper eject/feedshift section consists of the conveying path which sends the paper that has passed the
fuser section to the top tray, duplex conveying section or job separator.
5 14 13
10
11
7
3
9
2
12
1 8 6
Figure 2-1-22 Eject/Feed shift section
1. Middle pulley 8. Lower duplex roller

2. Eject roller 9. Lower change guide
3. Eject pulley 10. Upper change guide
4. Eject roller 11. Eject full sensor (EFS)
5. Eject pulley 12. Actuator (eject full sensor)
6. Upper duplex roller 13. Switchback sensor (SBS)
7. Duplex pulley 14. Actuator (switchback sensor)
2-1-22
2LK/2LN/2LM/2LC
JUNC_SOL_REM
YC5-19
JUNC_SOL_RET FSSOL
YC5-20
EXIT_FEED_SENS SBS
YC5-13
EXIT_PAP_SENS EFS
YC5-16
FRPWB
SB_CORE_B/
YC5-8
SB_CORE_A/
YC5-9
SB_CORE_B MM
YC5-10
SB_CORE_A
YC5-11
YC3 YC7
EPWB
Figure 2-1-23 Eject/Feed shift section block diagram
2-1-23
2LK/2LN/2LM/2LC
2-1-8 Duplex conveying section

The duplex conveying section consists of conveying path which sends the paper sent from the eject/feedshift
section to the paper feed/conveying section when duplex printing.
1
4
5 2
9
5
4 8
Figure 2-1-24 Duplex conveying section
1. Upper duplex roller 6. Duplex sensor 1 (DUS1)

2. Middle duplex roller 7. Actuator (duplex sensor 1)
3. Lower duplex roller 8. Duplex sensor 2 (DUS2)
4. Duplex pulleys A 9. Actuator (duplex sensor 2)
5. Duplex pulleys B
2-1-24
2LK/2LN/2LM/2LC
DU_ENTER_SENS DUS1
YC23-1 YC13-12 YC11-2
DU_CL1_REM
YC23-4 YC13-9 YC11-9 DUCL1
FPWB1 RYPWB
DU_SENS DUS2
YC14-5 YC1-14 YC9-2
DU_CL2_REM
YC14-12 YC1-7 YC7-2 DUCL2
YC1
YC2
YC6
YC5
EPWB
Figure 2-1-25 Duplex conveying section block diagram (30 ppm/35 ppm model)
2-1-25
2LK/2LN/2LM/2LC
DU_ENTER_SENS DUS1
YC23-1 YC13-12 YC11-2
DU1_B/
YC23-6 YC13-7 YC16-1
DU1_A/
YC23-7 YC13-6 YC16-2
DU1_B DUM1
YC23-8 YC13-5 YC16-3
DU1_A
YC23-9 YC13-4 YC16-4
FPWB1 RYPWB
DU_SENS DUS2
YC14-5 YC1-14 YC9-2
DU2_B/
YC14-14 YC1-5 YC7-5
DU2_A/
YC14-15 YC1-4 YC7-6
DU2_B DUM2
YC14-16 YC1-3 YC7-7
DU2_A
YC14-17 YC1-2 YC7-8
YC1
YC2
YC6
YC5
EPWB
Figure 2-1-26 Duplex conveying section block diagram (45 ppm/55 ppm model)
2-1-26
2LK/2LN/2LM/2LC
2-2-1 Electrical parts layout

2-2 Electrical Parts Layout
(1) PWBs
10
9 11
7
1 12
2 8
35 33
14
34
13
6 32
31
30 29 28 27
16
18 5
22 21 20 19
26 25 24 23
15
17 3
Machine right
Machine inside
4 Machine left
Figure 2-2-1 PWBs
1. Main PWB (MPWB) .............................. Controls the software such as the print data processing and
provides the interface with computers.
2. Engine PWB (EPWB)............................ Controls printer hardware such as high voltage/bias output con-
trol, paper conveying system control, and fuser temperature con-
trol, etc.
3. Power source PWB (PSPWB) .............. After full-wave rectification of AC power source input, switching
for converting to 24 V DC and 12 V DC for output. Controls the
fuser heater.
4. Current PWB (CRPWB)*....................... After full-wave rectification of AC power source input, switching
for converting to 5 V DC for output.
5. High voltage PWB 1 (HVPWB1) ........... Generates main charging and developing bias.
6. High voltage PWB 2 (HVPWB2) ........... Generates transfer bias and separation bias.
7. ISC PWB (ISCPWB) ............................. Controls the scanner section.
8. CCD PWB (CCDPWB).......................... Reads the image of originals.
9. LED PWB (LEDPWB) ........................... Exposes originals.
2-2-1
2LK/2LN/2LM/2LC
10. Operation PWB 1 (OPWB1).................. Controls touch panel and LCD indication.
11. Operation PWB 2 (OPWB2).................. Consists of the LED indicators and key switches.
12. Operation PWB 3 (OPWB3).................. Consists of the LED indicators.
13. Front PWB (FRPWB) ............................ Consists of wiring relay circuit between engine PWB and drum
units, developer units, eject unit.
14. Feed PWB 1 (FPWB1).......................... Consists of wiring relay circuit between engine PWB and fuser
drive unit, relay PWB.
15. Feed PWB 2 (FPWB2).......................... Consists of wiring relay circuit between engine PWB and paper
conveying section, drive section.
16. Relay PWB (RPWB) ............................. Consists of wiring relay circuit between feed PWB 1 and paper
conveying unit.
17. Motor control PWB (MCPWB)............... Consists of wiring relay circuit between engine PWB and drum
motors, developer motors.
18. LSU relay PWB (LSURPWB)................ Consists of wiring relay circuit between engine PWB and laser
scanner unit.
19. APC PWB K (APCPWB-K) ................... Generates and controls the laser beam (black).
20. APC PWB M (APCPWB-M) .................. Generates and controls the laser beam (magenta).
21. APC PWB C (APCPWB-C) ................... Generates and controls the laser beam (cyan).
22. APC PWB Y (APCPWB-Y) ................... Generates and controls the laser beam (yellow).
23. PD PWB K (PDPWB-K) ........................ Controls horizontal synchronizing timing of laser beam (black).
24. PD PWB M (PDPWB-M) ....................... Controls horizontal synchronizing timing of laser beam (magenta).
25. PD PWB C (PDPWB-C)........................ Controls horizontal synchronizing timing of laser beam (cyan).
26. PD PWB Y (PDPWB-Y) ........................ Controls horizontal synchronizing timing of laser beam (yellow).
27. Drum PWB K (DRPWB-K) .................... Drum individual information in EEPROM storage.
28. Drum PWB M (DRPWB-M) ................... Drum individual information in EEPROM storage.
29. Drum PWB C (DRPWB-C).................... Drum individual information in EEPROM storage.
30. Drum PWB Y (DRPWB-Y) .................... Drum individual information in EEPROM storage.
31. Transfer PWB (TRPWB) ....................... Transfer belt individual information in EEPROM storage.
32. Fuser PWB (FUPWB) ........................... Relays wirings from electrical components on the fuser unit.
33. Fuser IH PWB (FIHPWB)...................... Controls the fuser IH.
34. RFID PWB (RFPWB) ............................ Reads the container information.
35. Interface PWB (IFPWB) ........................ Consists of wiring relay circuits between main PWB and Fax con-
trol PWB.
*: 45 ppm model /55 ppm model only.
2-2-2
2LK/2LN/2LM/2LC
List of correspondences of PWB names
No. Name used in service manual Name used in parts list

1 Main PWB (MPWB) PARTS PWB MAIN ASSY SP
2 Engine PWB (EPWB) PARTS PWB ENGINE ASSY SP
3 Power source PWB (PSPWB) PARTS UNIT LOW VOLTAGE SP
4 Current PWB (CRPWB) PARTS PWB CURRENT AVE ASSY SP
5 High voltage PWB 1 (HVPWB1) PARTS UNIT HIGH VOLTAGE MAIN SP
6 High voltage PWB 2 (HVPWB2) PARTS UNIT HIGH VOLTAGE TRANSFER SP
7 ISC PWB (ISCPWB) PARTS PWB ISC ASSY SP
8 CCD PWB (CCDPWB) -
9 LED PWB (LEDPWB) -
10 Operation PWB 1 (OPWB1) PARTS PWB PANEL MAIN ASSY J SP
11 Operation PWB 2 (OPWB2) PARTS PWB OPERATION ASSY SP
12 Operation PWB 3 (OPWB3) PARTS PWB OPERATION LED ASSY SP
13 Front PWB (FRPWB) PARTS PWB FRONT CLR ASSY SP
14 Feed PWB 1 (FPWB1) PARTS PWB FEED 1 ASSY SP
15 Feed PWB 2 (FPWB2) PARTS PWB FEED 2 ASSY SP
16 Relay PWB (RPWB) PARTS PWB JUNCTION ASSY SP
17 Motor control PWB (MCPWB) PARTS PWB MOTOR CONTROL ASSY SP
18 LSU relay PWB (LSURPWB) PARTS PWB LSU JUNC CLR ASSY SP
19 APC PWB K (APCPWB-K) -
20 APC PWB M (APCPWB-M) -
21 APC PWB C (APCPWB-C) -
22 APC PWB Y (APCPWB-Y) -
23 PD PWB K (PDPWB-K) -
24 PD PWB M (PDPWB-M) -
25 PD PWB C (PDPWB-C) -
26 PD PWB Y (PDPWB-Y) -
27 Drum PWB K (DRPWB-K) -
28 Drum PWB M (DRPWB-M) -
29 Drum PWB C (DRPWB-C) -
30 Drum PWB Y (DRPWB-Y) -
31 Transfer PWB (TRPWB) -
32 Fuser PWB (FUPWB) -
33 Fuser IH PWB (FIHPWB) -
34 RFID PWB (RFPWB) PARTS PWB RFID ASSY SP
35 Interface PWB (IFPWB) PARTS PWB KUIO ASSY SP
2-2-3
2LK/2LN/2LM/2LC
(2) Switches and sensors
28 29
30
55
54 56
53
34 33 32 31 48 52
51
50
47 49
2 41 43 46
44
63 42
45 58
39,40
57
38 37 36 35 27 61 19
26 24 18 21 23
60 22
3 59
25
15 20 1
5
7 17 62
13
4
8
11 16 Machine right
6
Machine inside
14 9 64
10 Machine left
12
Figure 2-2-2 Switches and sensors
1. Main power switch (MSW) .................... Turns ON/OFF the AC power source.
2. Front cover switch (FRCSW) ................ Detects the opening and closing of the front cover.
3. Paper sensor 1 (PS1) ........................... Detects the presence of paper (cassette 1).
4. Paper sensor 2 (PS2) ........................... Detects the presence of paper (cassette 2).
5. Lift sensor 1 (LS1)................................. Detects activation of upper limit of the bottom plate (cassette 1).
6. Lift sensor 2 (LS2)................................. Detects activation of upper limit of the bottom plate (cassette 2).
7. Paper gauge sensor 1 (U) (PGS1(U))... Detects the paper gauge (cassette 1).
8. Paper gauge sensor 1 (L) (PGS1(L)).... Detects the paper gauge (cassette 1).
9. Paper gauge sensor 2 (U) (PGS2(U))... Detects the paper gauge (cassette 2).
10. Paper gauge sensor 2 (L) (PGS2(L)).... Detects the paper gauge (cassette 2).
11. Paper length switch 1 (PLSW1) ............ Detects the length of paper (cassette 1).
12. Paper length switch 2 (PLSW2) ............ Detects the length of paper (cassette 2).
13. Paper width switch 1 (PWSW1) ............ Detects the width of paper (cassette 1).
14. Paper width switch 2 (PWSW2) ............ Detects the width of paper (cassette 2).
15. Feed sensor 1 (FS1) ............................. Detects a paper misfeed in the paper feed section (cassette 1).
16. Feed sensor 2 (FS2) ............................. Detects a paper misfeed in the paper feed section (cassette 2).
17. Paper conveying sensor (PCS)............. Detects a paper misfeed in the vertical conveying section.
18. MP paper sensor (MPPS) ..................... Detects the presence of paper (MP tray).
2-2-4
2LK/2LN/2LM/2LC
19. MP lift sensor 1 (MPLS1) ...................... Detects activation of upper limit of the MP plate.
20. MP lift sensor 2 (MPLS2) ...................... Detects activation of lower limit of the MP plate.
21. MP paper length switch (MPPLSW)...... Detects the length of paper (MP tray).
22. MP paper width switch (MPPWSW)...... Detects the width of paper (MP tray).
23. MP tray switch (MPTSW)...................... Detects the MP tray extension is extend.
24. MP feed sensor (MPFS) ....................... Detects a paper misfeed in the MP paper feed section.
25. Middle sensor (MS)............................... Detects a paper misfeed in the paper conveying section.
26. Regist deflection sensor (RDS)............. Detects the deflection in the paper.
27. Registration sensor (RS)....................... Controls the secondary paper feed start timing.
28. Original size sensor (OSS) ................... Detects the size of the original.
29. Original detection switch (ODSW) ........ Detects the opening/closing of the document processor.
30. Home position sensor (HPS) ................ Detects the optical system in the home position.
31. Screw sensor K (SRS-K) ...................... Controls the toner replenishing for the toner container K.
32. Screw sensor M (SRS-M) ..................... Controls the toner replenishing for the toner container M.
33. Screw sensor C (SRS-C) ...................... Controls the toner replenishing for the toner container C.
34. Screw sensor Y (SRS-Y) ...................... Controls the toner replenishing for the toner container Y.
35. Toner sensor K (TS-K) .......................... Detects the toner density in the developing unit K.
36. Toner sensor M (TS-M) ......................... Detects the toner density in the developing unit M.
37. Toner sensor C (TS-C).......................... Detects the toner density in the developing unit C.
38. Toner sensor Y (TS-Y) .......................... Detects the toner density in the developing unit Y.
39. ID sensor 1 (IDS1) ................................ Measures image density for color calibration.
40. ID sensor 2 (IDS2) ................................ Measures image density for color calibration.
41. Color release sensor (CRS).................. Detects separation of primary transfer rollers M, C, and Y.
42. Transfer belt sensor (TRBLS) ............... Detects positioning of transfer belt rotation.
43. Transfer skew sensor (TRSS)............... Detects skew of transfer belt center position.
44. Transfer edge sensor (TRES) ............... Detects edge position of the transfer belt.
45. Transfer release sensor (TRRS) ........... Detects separation of secondary transfer roller.
46. Loop sensor (LPS) ................................ Detects a paper misfeed. Controls the fuser motor by detecting
deflection in the paper.
47. Fuser belt sensor (FUBLS) ................... Detects positioning of fuser belt rotation.
48. Fuser release sensor (FURS) ............... Detects fuser pressure release setting (envelope mode).
49. Fuser thermistor 1 (FTH1) .................... Detects the heat roller (fuser belt) temperature.
52. Fuser thermistor 4 (FTH4) .................... Detects the press roller temperature.
53. Fuser eject sensor (FUES) ................... Detects a paper misfeed in the fuser section.
54. Eject full sensor (EFS) .......................... Detects a paper misfeed in the eject section. Detects when the
inner tray is full.
55. Switchback sensor (SBS) ..................... Detects a paper misfeed in the eject and switchback sections.
56. Duplex sensor 1 (DUS1) ....................... Detects a paper misfeed in the duplex section.
57. Duplex sensor 2 (DUS2) ....................... Detects a paper misfeed in the duplex section.
58. Duplex cover switch (DUCSW) ............. Detects the opening and closing of the duplex cover.
59. Waste toner sensor 1 (WTS1)............... Detects when the waste toner box is full.
60. Waste toner sensor 2 (WTS2)............... Detects when the waste toner box is full.
61. Paper conveying unit switch
(PCUSW) .............................................. Detects the opening and closing of the paper conveying unit.
62. Paper conveying cover switch
(DUCSW) .............................................. Detects the opening and closing of the paper conveying cover.
63. Outer temperature sensor 1
(OTEMS1)............................................. Detects the outside temperature and humidity.
64. Outer temperature sensor 2
(OTEMS2)............................................. Detects the outside temperature and humidity.
2-2-5
2LK/2LN/2LM/2LC
(3) Motors
35 36
19 18 17 16 33
34
30
29 31
21 28
20 32
25 24 23 22
27 10
15 14 13 12 1 37
26
11 4
9 8 7 6
2
Machine right
Machine inside
3 Machine left
Figure 2-2-3 Motors
1. Paper feed motor (PFM) ....................... Drives the paper feed section.
2. Lift motor 1 (LM1).................................. Operates the bottom plate (cassette 1).
3. Lift motor 2 (LM2).................................. Operates the bottom plate (cassette 2).
4. MP lift motor (MPLM) ............................ Operates the MP plate.
5. Scanner motor (SM).............................. Drives the optical system.
6. Polygon motor K (PM-K) ....................... Drives the polygon mirror K.
7. Polygon motor M (PM-M)...................... Drives the polygon mirror M.
8. Polygon motor C (PM-C)....................... Drives the polygon mirror C.
9. Polygon motor Y (PM-Y) ....................... Drives the polygon mirror Y.
10. Registration motor (RM)*2...................... Drives the registration section.
11. Middle motor (MM)*2 .............................. Drives the paper conveying section.
12. Drum motor K (DRM-K) ........................ Drives the drum unit K.
13. Drum motor M (DRM-M)*2 ..................... Drives the drum unit M.
14. Drum motor C (DRM-C)*2 ...................... Drives the drum unit C.
Drum motor MCY (DRM-MCY)*1 ........... Drives the drum units M, C and Y.
15. Drum motor Y (DRM-Y)*2 ...................... Drives the drum unit Y.
16. Toner motor K (TM-K) ........................... Replenishes toner to the developing unit K
17. Toner motor M (TM-M) .......................... Replenishes toner to the developing unit M
2-2-6
2LK/2LN/2LM/2LC
18. Toner motor C (TM-C)........................... Replenishes toner to the developing unit C

19. Toner motor Y (TM-Y) ........................... Replenishes toner to the developing unit Y
20. Developer motor K (DEVM-K)............... Drives the developer unit K.
21. Developer motor MCY (DEVM-MCY) ... Drives the developer units M, C and Y.
22. Vibration motor K (VM-K) ...................... Toner lump in the developer unit K vibrates.
23. Vibration motor M (VM-M)..................... Toner lump in the developer unit M vibrates.
24. Vibration motor C (VM-C) ..................... Toner lump in the developer unit C vibrates.
25. Vibration motor Y (VM-Y) ...................... Toner lump in the developer unit Y vibrates.
26. LSU cleaning motor (LSUCM) .............. Drives LSU dust shield glass cleaning system.
27. Waste toner motor (WTM)..................... Drives waste toner system.
28. Transfer motor (TRM) ........................... Drives the transfer section.
29. Transfer cleaning motor (TRCM) .......... Drives the transfer cleaning section.
30. Color release motor (CRM)................... Drives separation of primary transfer rollers M, C, and Y.
31. Transfer skew motor (TRSM)................ Drives skew of transfer tension roller.
32. Transfer release motor (TRRM) ............ Drives separation of secondary transfer roller.
33. Fuser motor (FUM) ............................... Drives the fuser section.
34. Fuser release motor (FURM) ................ Drives fuser pressure release.
35. Eject motor (EM) ................................... Drives the eject section.
36. Duplex motor 1 (DUM1)*2 ...................... Drives the duplex section.
37. Duplex motor 2 (DUM2)*2 ...................... Drives the duplex section.
*1: 30 ppm model /35 ppm model only.

2-2-7
2LK/2LN/2LM/2LC
(4) Fan motors
16
10,11
20 15 17,18 10 17 18 11
13
12 8,9
1 2
6,7
4 3 14
Machine right
19 Machine inside
Machine left
Figure 2-2-4 Motors
1. Toner fan motor 1 (TFM1) ..................... Cools the toner container section.
2. Toner fan motor 2 (TFM2) ..................... Cools the toner container section.
3. Developer fan motor 1 (DEVFM1) ........ Cools the developer section.
4. Developer fan motor 2 (DEVFM2) ........ Cools the developer section.
5. LSU fan motor (LSUFM) ....................... Cools the laser scanner unit section.
6. Belt fan motor 1 (BLFM1)...................... Cools the transfer belt section.
10. Fuser front fan motor (FUFFM)............. Cools the fuser section (front side).
11. Fuser rear fan motor (FURFM) ............. Cools the fuser section (rear side).
12. Coil fan motor 1 (CFM1) ....................... Cools the IH coil.
13. Coil fan motor 2 (CFM2) ....................... Cools the IH coil.
14. IH fan motor (IHFM) .............................. Cools the fuser IH PWB.
15. Eject front fan motor (EFFM) ................ Cools the eject section (front side).
16. Eject rear fan motor (ERFM)................. Cools the eject section (rear side).
2-2-8
2LK/2LN/2LM/2LC
17. Eject fan motor (EFM)........................... Cools the eject section.

18. Eject fan motor (EFM)........................... Cools the eject section.
19. Power source fan motor (PSFM) .......... Cools the power source section.
20. Controller fan motor (CONFM).............. Cools the controller section.
2-2-9
2LK/2LN/2LM/2LC
(5) Others
13
22
9
19
20
18 17 16 15 8
10
14 7
6
1
11
3
5
2
12 Machine right
4
Machine inside
21 Machine left
Figure 2-2-5 Others
1. Paper feed clutch 1 (PFCL1) ................ Primary paper feed from cassette 1.
2. Paper feed clutch 1 (PFCL1) ................ Primary paper feed from cassette 2.
3. Assist clutch 1 (ASCL1)*2 ...................... Controls the drive of the assist roller.
4. Assist clutch 2 (ASCL2)*2 ...................... Controls the drive of the assist roller.
5. Paper conveying clutch (PCCL)............ Controls the drive of vertical conveying section.
6. MP paper feed clutch (MPPFCL) .......... Controls primary paper feed from the MP tray.
7. Middle clutch (MCL)*1 ............................ Controls the drive of paper conveying section.
8. Registration clutch (RCL)*1 .................... Controls the secondary paper feed.
9. Duplex clutch 1 (DUCL1)*1 .................... Controls the drive of duplex section.
10. Duplex clutch 2 (DUCL2)*1 .................... Controls the drive of duplex section.
11. Pickup solenoid 1 (PUSOL1)*2 .............. Controls the pickup roller.
12. Pickup solenoid 2 (PUSOL2)*2 .............. Controls the pickup roller.
13. Feedshift solenoid (FSSOL).................. Controls the feedshift guide.
14. Cleaning solenoid (CLSOL) .................. Controls the ID sensor cleaning.
15. Cleaning lamp K (CL-K) ........................ Eliminates the residual electrostatic charge on the drum (black).
16. Cleaning lamp M (CL-M)....................... Eliminates the residual electrostatic charge on the drum
(magenta).
17. Cleaning lamp C (CL-C)........................ Eliminates the residual electrostatic charge on the drum (cyan).
2-2-10
2LK/2LN/2LM/2LC
18. Cleaning lamp Y (CL-Y) ........................ Eliminates the residual electrostatic charge on the drum (yellow).
19. Fuser IH (FIH) ....................................... Heats the heat roller (fuser belt).
20. Fuser thermostat (FTS)......................... Prevents overheating of the heat roller (fuser belt).
21. Cassette heater (CH) ............................ Dehumidifies the cassette section (option).
22. Hard disk (HDD).................................... Storages the image data and information of job accounting mode.

2-2-11
2LK/2LN/2LM/2LC
2-2-12
2LK/2LN/2LM/2LC
2-3-1 Main PWB

2-3 Operation of the PWBs
5
BK
WH
1 6
U45
YC12
YC13 YC5
1
YC25 YC17 YC21 1 13
1 7
50 YC16 1
1 8 YC11 U25
U113
1 6 YC30
80 1
YC20
1
YC7 YC10
1
12
10
U112
YC33
YS4
1
1 72
CODE FLS
1 2
YC23 YS2 YS1
1 3 1 72
YS3
YC27
U1
1 3 YC32
U6
8 1
200
200
7 1
1
YC24 YC1
YC18
9
BLACK
1 40
15
5
YC9 7 1 BAT1
YC3 YC2
1
YC8
BLUE
1 5
YC15 YC14
Figure 2-3-1 Main PWB silk-screen diagram
2-3-1
2LK/2LN/2LM/2LC
Connector Pin Signal I/O Voltage Description

YC1 1 GND - - Ground
Connected to 2 TXP O - HDD1 data signal
hard disk 1
3 TXN O - HDD1 data signal
4 GND - - Ground
5 RXN I - HDD1 data signal
6 RXP I - HDD1 data signal
7 GND - - Ground
Connected to 2 TXP O - HDD2 data signal
hard disk 2
3 TXN O - HDD2 data signal
4 GND - - Ground
5 RXN I - HDD2 data signal
6 RXP I - HDD2 data signal
7 GND - - Ground
YC3 1 HSYNC_AN O 0/3.3 V DC (pulse) Image control signal
Connected to 2 HSYNC_AP O 0/3.3 V DC (pulse) Image control signal
engine PWB
3 HSYNC_BN O 0/3.3 V DC (pulse) Image control signal
4 HSYNC_BP O 0/3.3 V DC (pulse) Image control signal
5 HSYNC_CN O 0/3.3 V DC (pulse) Image control signal
6 HSYNC_CP O 0/3.3 V DC (pulse) Image control signal
7 HSYNC_DN O 0/3.3 V DC (pulse) Image control signal
8 HSYNC_DP O 0/3.3 V DC (pulse) Image control signal
9 VSYNC_AN O 0/3.3 V DC (pulse) Image control signal
10 VSYNC_AP O 0/3.3 V DC (pulse) Image control signal
11 VSYNC_BN O 0/3.3 V DC (pulse) Image control signal
12 VSYNC_BP O 0/3.3 V DC (pulse) Image control signal
13 VSYNC_CN O 0/3.3 V DC (pulse) Image control signal
14 VSYNC_CP O 0/3.3 V DC (pulse) Image control signal
15 VSYNC_DN O 0/3.3 V DC (pulse) Image control signal
16 VSYNC_DP O 0/3.3 V DC (pulse) Image control signal
17 SGND - - Ground
18 TCLKP O 0/3.3 V DC (pulse) Clock signal
19 TCLKN O 0/3.3 V DC (pulse) Clock signal
20 SGND - - Ground
21 TCP O 0/3.3 V DC (pulse) Image control signal
22 TCN O 0/3.3 V DC (pulse) Image control signal
2-3-2
2LK/2LN/2LM/2LC

YC3 23 SGND - - Ground
Connected to 24 TBP O 0/3.3 V DC (pulse) Image control signal
engine PWB
25 TBN O 0/3.3 V DC (pulse) Image control signal
26 SGND - - Ground
27 TAP O 0/3.3 V DC (pulse) Image control signal
28 TAN O 0/3.3 V DC (pulse) Image control signal
29 SGND - - Ground
30 SLEEP O 0/3.3 V DC Sleep signal
31 HLD_ENG O 0/3.3 V DC Engine hold signal
32 NC - - Not used
33 SGND - - Ground
34 EG IRN O 0/3.3 V DC Engine interrupt signal
35 EG SO I 0/3.3 V DC (pulse) Serial communication data signal
36 EG SBSY O 0/3.3 V DC Engine busy signal
37 EG SDIR O 0/3.3 V DC Engine communication direction sig-
nal
38 EG_SI O 0/3.3 V DC (pulse) Serial communication data signal
39 EG_SCLK O 0/3.3 V DC (pulse) Engine lock signal
40 SGND - - Ground
YC5 1 TD1+ O 0/3.3 V DC (pulse) Transmission data
Connected to 2 TD1- O 0/3.3 V DC (pulse) Transmission data
ethernet
3 TD2+ O 0/3.3 V DC (pulse) Transmission data
4 TD2- O 0/3.3 V DC (pulse) Transmission data
5 CT1 O 3.3 V DC 3.3 V DC power output
6 CT2 O 3.3 V DC 3.3 V DC power output
11 GRLED_A1 O 0/3.3 V DC LED emitter signal
12 GRLED_K1 O 0/3.3 V DC LED emitter signal
13 YWLED_A2 O 0/3.3 V DC LED emitter signal
14 YWLED_K2 O 0/3.3 V DC LED emitter signal
2-3-3
2LK/2LN/2LM/2LC

YC7 1 KMDET I 0/3.3 V DC KMAS set signal
Connected to 2 NC - - Not used
KMAS
3 KMDREQ I 0/3.3 V DC KMAS control signal
4 KMACK O 0/3.3 V DC KMAS control signal
5 KMRXD O 0/3.3 V DC (pulse) KMAS received data signal
6 SGND - - Ground
7 KMTXD I 0/3.3 V DC (pulse) KMAS transmission data signal
8 SGND - - Ground
9 SGND - - Ground
10 SGND - - Ground
11 +5V O 5 V DC 5 V DC power to KMAS
12 +5V O 5 V DC 5 V DC power to KMAS
YC8 1 RESET0 I 0/3.3 V DC Reset signal
Connected to 2 WAKEUP0 O 0/3.3 V DC Control signal
interface
3 AUDIO0 I Analog Audio signal
PWB
4 GND - - Ground
5 USB_DP0 I/O - USB data signal
6 USB_DN0 I/O - USB data signal
7 VBUS0 O 3.3 V DC 3.3 V DC power to IFPWB
8 GND - - Ground
9 RESET1 I 0/3.3 V DC Reset signal
10 WAKEUP1 O 0/3.3 V DC Control signal
11 AUDIO1 I Analog Audio signal
12 GND - - Ground
13 USB_DP1 I/O - USB data signal
14 USB_DN1 I/O - USB data signal
15 VBUS1 O 3.3 V DC 3.3 V DC power to IFPWB
Connected to 2 5V_CUT0 I 0/3.3 V DC 5 V DC cut signal
interface
3 GND - - Ground
PWB
4 5V O 5 V DC 5 V DC power to IFPWB
5 GND - - Ground
6 5V_CUT1 I 0/3.3 V DC 5 V DC cut signal
2-3-4
2LK/2LN/2LM/2LC

Connected to 2 GND - - Ground
DP relay
3 3.3V O 3.3 V DC 3.3 V DC power to DPRPWB
PWB
7 VCLKB I 0/3.3 V DC (pulse) DPRPWB clock signal
8 VSYNCB I 0/3.3 V DC (pulse) DPRPWB VSYNCB signal
9 HSYNCB I 0/3.3 V DC (pulse) DPRPWB HSYNCB signal
10 MREB I 0/3.3 V DC (pulse) DPRPWB MREB signal
11 GND - - Ground
12 DRB0 I 0/3.3 V DC (pulse) Image data signal
20 GND - - Ground
21 DGB0 I 0/3.3 V DC (pulse) Image data signal
29 GND - - Ground
30 DBB0 I 0/3.3 V DC (pulse) Image data signal
2-3-5
2LK/2LN/2LM/2LC

YC10 37 DBB7 I 0/3.3 V DC (pulse) Image data signal
Connected to 38 HHALF O 0/3.3 V DC DPRPWB Control signal
DP main
39 SLEEP O 0/3.3 V DC DPRPWB Control signal
PWB
40 TWS_DET I 0/3.3 V DC DPRPWB Control signal
41 GND - - Ground
42 LA2 O 0/3.3 V DC (pulse) Address bus signal
58 GND - - Ground
59 LD0 I/O 0/3.3 V DC (pulse) Data bus signal
67 GND - - Ground
68 INT I 0/3.3 V DC DPRPWB Control signal
69 RESETZ O 0/3.3 V DC DPRPWB Control signal
70 GND - - Ground
71 CEZ O 0/3.3 V DC (pulse) DPRPWB Control signal
72 WEZ O 0/3.3 V DC (pulse) DPRPWB Control signal
2-3-6
2LK/2LN/2LM/2LC

YC10 73 OEZ O 0/3.3 V DC (pulse) DPRPWB Control signal
Connected to 74 SCLKIN O 0/3.3 V DC (pulse) DPRPWB clock signal
DP main
PWB
79 GND - - Ground
80 GND - - Ground
Connected to 2 SC_IRN O 0/3.3 V DC Scanner interrupt signal
ISC PWB
3 SC_DIR O 0/3.3 V DC Scanner communication direction sig-
nal
4 SC_HLDN O 0/3.3 V DC Scanner hold signal
5 SC_BSY O 0/3.3 V DC Scanner busy signal
6 SC_SI O 0/3.3 V DC (pulse) Serial communication data signal
7 SC_SO I 0/3.3 V DC (pulse) Serial communication data signal
8 SC_CLK O 0/3.3 V DC (pulse) Scanner clock signal
YC12 1 DEEP_POWERO O 0/3.3 V DC Sleep return signal
N
Connected to 2 ENERGY_SAVE O 0/3.3 V DC Energy save signal
operation
3 SUPND_POWER O 3.3 V DC 3.3 V DC power to OPWB1
PWB 1
4 LED_MEMORY_N O 0/3.3 V DC Memory LED control signal
5 LED_ATTENTION O 0/3.3 V DC Attention LED control signal
_N
6 LED_PROCESSI O 0/3.3 V DC Processing LED control signal
NG_N
7 SHUT_DOWN O 0/3.3 V DC 24 V down signal
8 LIGHTOFF_POW O 0/3.3 V DC Sleep return signal
ERON
9 AUDIO O Analog Audio output signal
10 PANEL RESET O 0/3.3 V DC Reset signal
11 INT_POWERKEY I 0/3.3 V DC Power key: On/Off
_N
12 PANEL_STATUS I 0/3.3 V DC Operation panel status signal
13 GND - - Ground
2-3-7
2LK/2LN/2LM/2LC

Connected to 2 D3 I/O 0/3.3 V DC (pulse) Data bus signal
CF card
3 D4 I/O 0/3.3 V DC (pulse) Data bus signal
7 /CE1 O 0/3.3 V DC Control signal
8 A10 O 0/3.3 V DC (pulse) Address bus signal
9 /OE O 0/3.3 V DC Control signal
13 VCC O 0/3.3 V DC Control signal
24 WP O 0/3.3 V DC Control signal
25 /CD2 O 0/3.3 V DC Control signal
26 /CD1 O 0/3.3 V DC Control signal
32 /CE2 O 0/3.3 V DC Control signal
33 /VS1 O 0/3.3 V DC Control signal
34 /IORD O 0/3.3 V DC Control signal
35 /IOWD O 0/3.3 V DC Control signal
36 /WE O 0/3.3 V DC Control signal
2-3-8
2LK/2LN/2LM/2LC

YC16 37 RDY/BSY I 0/3.3 V DC Control signal
Connected to 38 VCC O 0/3.3 V DC Control signal
CF card
39 CSEL O 0/3.3 V DC Control signal
40 VS2 O 0/3.3 V DC Control signal
41 RESET I 0/3.3 V DC Reset signal
42 /WAIT O 0/3.3 V DC Control signal
43 INPACK O 0/3.3 V DC Control signal
44 /REG I 0/3.3 V DC REG signal
45 BVD2 O 0/3.3 V DC Control signal
46 BVD1 O 0/3.3 V DC Control signal
50 GND - - Ground
YC17 1 VBUS O 5 V DC 5 V DC power output
Connected to 2 DATA - I/O - USB data signal
operation
3 DATA + I/O - USB data signal
PWB 1
4 NC - - Not used
5 GND - - Ground
Connected to 2 DATA- I/O - USB data signal
USB
3 DATA+ I/O - USB data signal
4 GND - - Ground
Connected to 2 DATA - I/O - USB data signal
USB host 3 DATA + I/O - USB data signal
4 NC - - Not used
5 GND - - Ground
YC23 1 +12V O 12 V DC CONFM: On/Off
controller fan
motor
2-3-9
2LK/2LN/2LM/2LC

YC24 1 +12V O 12 V DC 12 V DC power from PSPWB
Connected to 2 +12V O 12 V DC 12 V DC power from PSPWB
power source
3 +12V O 12 V DC 12 V DC power from PSPWB
PWB
4 +12V O 12 V DC 12 V DC power from PSPWB
5 GND - - Ground
6 GND - - Ground
7 GND - - Ground
8 GND - - Ground
Connected to 2 HTPDN I 0/3.3 V DC Control signal
ISC PWB
3 LOCKN I 0/3.3 V DC Lock signal
4 GND - - Ground
5 RX0N I 0/3.3 V DC (pulse) Received data signal
6 RX0P I 0/3.3 V DC (pulse) Received data signal
7 GND - - Ground
Connected to 2 +5V_HDD O 5 V DC 5 V DC power to HDD1
hard disk 1
3 GND - - Ground
YC30 1 +5V O 5 V DC 5 V DC power from OPWB1
Connected to 2 +5V O 5 V DC 5 V DC power from OPWB1
operation
3 +5V O 5 V DC 5 V DC power from OPWB1
PWB 1
4 GND - - Ground
5 GND - - Ground
6 GND - - Ground
Connected to 2 +5V_HDD O 5 V DC 5 V DC power to HDD2
hard disk 2
3 GND - - Ground
2-3-10
2LK/2LN/2LM/2LC

Connected to 2 SDOCLK O 0/3.3 V DC (pulse) Clock signal
fiery relay
3 SDO O 0/3.3 V DC (pulse) Serial communication data signal
PWB
4 SGND - - Ground
5 SDICLK O 0/3.3 V DC (pulse) Clock signal
6 SDI I 0/3.3 V DC (pulse) Serial communication data signal
7 SGND - - Ground
8 SGND - - Ground
9 12V O 12 V DC 12 V DC power to FIRPWB
10 12V O 12 V DC 12 V DC power to FIRPWB
2-3-11
2LK/2LN/2LM/2LC
2-3-2 Engine PWB
A10 A1
24
1
A20 A1 1 12 6 1 20 1 B19 B1
4
2 1
YC27
YC18
8
YC23 YC22
1
B10 YC25 B1
B1 YC26 B20 A1 A19
YC20 YC19
1
YC24 YC21
7
12
3 1
YC17 11
14
YC49
15
13
12
1 YC1
YC16
A16
B1
22
1
1 10
YC3
28
U4
1
YC2
YC15
1
1 4
U1
B16
YC4
A1
6
U100
1
U13
60
1
YC12
YC6
YC4
40
U8
1
YC48
1
64
1 50
64
20
21
YC5
YC11
1 11
12 1
50
YC7 YC10
1
1 YC50 40 1 YC46 40 1 YC47 40
22
YC9 12 YC8
1 50 1 40
Figure 2-3-2 Engine PWB silk-screen diagram
2-3-12
2LK/2LN/2LM/2LC

Connected to 2 +5V I 5 V DC 5 V DC power from FPWB1
feed PWB 1
3 GND - - Ground
4 +12V I 12 V DC 12 V DC power from FPWB1
5 GND - - Ground
6 GND - - Ground
7 +24V1 I 24 V DC 24 V DC power from FPWB1
8 +24V1 I 24 V DC 24 V DC power from FPWB1
front PWB
3 GND - - Ground
4 GND - - Ground
5 GND - - Ground
6 +24V O 24 V DC 24 V DC power to FRPWB
9 +3.3V2 O 3.3 V DC 3.3 V DC power to FRPWB
10 +3.3V1 O 3.3 V DC 3.3 V DC power to FRPWB
YC3 A1 +24V1 O 24 V DC 24 V DC power to TRCM
Connected to A2 GND - - Ground
transfer belt
A3 ICL_MOT_REM I 0/3.3 V DC TRCM: On/Off
unit
A4 ICL_MOT_CLK O 0/3.3 V DC (pulse) TRCM clock signal
A5 ICL_MOT_RDY I 0/3.3 V DC TRCM ready signal
A6 ICL_MOT_DIR O 0/3.3 V DC TRCM drive switch signal
A7 RLS_MOT_DR O 0/24 V DC CRM: On/Off
A8 +24V1 O 24 V DC 24 V DC power to CRM
A9 GND - - Ground
A10 RLS_SENS I 0/3.3 V DC CRS: On/Off
A11 +5V O 5 V DC 5 V DC power to CRS
A12 ZIG_MOT_DR_C O 0/24 V DC TRSM: On/Off (CCW)
CW
A13 ZIG_MOT_DR_C O 0/24 V DC TRSM: On/Off (CW)
W
A14 GND - - Ground
A15 BLT_INDEX - - Not used
A16 +5V - - Ground
B1 GND - - Ground
2-3-13
2LK/2LN/2LM/2LC

YC3 B2 ZIG_SENS I 0/3.3 V DC TRSS: On/Off
Connected to B3 +5V O 5 V DC 5 V DC power to TRSS
transfer belt
B4 GND - - Ground
unit
B4 GND - - Ground
B5 BLT_SPEED I 0/3.3 V DC TRBLS: On/Off
B6 +5V O 5 V DC 5 V DC power to TRBLS
B7 TEMP I Analog TEMP signal
B8 ZIG_REV_SENS I 0/3.3 V DC TRES: On/Off
B9 GND - - Ground
B10 +5V O 5 V DC 5 V DC power to TRES
B11 +3.3V2 O 3.3 V DC 3.3 V DC power to TRPWB
B12 EEP_SCL2 O 0/3.3 V DC (pulse) EEPROM clock signal
B13 EEP_SDA2 I/O 0/3.3 V DC (pulse) EEPROM data signal
B14 GND - - Ground
B15 A0 - - Not used
B16 A1 - - Not used
Connected to 2 FEED_MOT_REM O 0/3.3 V DC PFM: On/Off
feed PWB 2
3 FEED_MOT_CLK O 0/3.3 V DC (pulse) PFM clock signal
4 FEED_MOT_RDY I 0/3.3 V DC PFM ready signal
5 FEED_MOT_DIR O 0/3.3 V DC PFM drive switch signal
6 FEED_CL1_REM O 0/24 V DC PFCL1: On/Off
8 ASIST_CL2 O 0/24 V DC ASCL2: On/Off
9 LIFT_MOT2_REM O 0/24 V DC LM2: On/Off
10 GND - - Ground
11 LIFT_MOT1_REM O 0/24 V DC LM1: On/Off
1
12 CAS2_WID I 0/3.3 V DC PWSW2: On/Off
13 CAS2_LNG3 I 0/3.3 V DC PLSW2: On/Off
20 GND - - Ground
2-3-14
2LK/2LN/2LM/2LC

YC4 21 CAS2_QUANT2 I 0/3.3 V DC PGS2(L): On/Off
Connected to 22 CAS2_QUANT1 I 0/3.3 V DC PGS2(U): On/Off
feed PWB 2
23 CAS1_QUANT2 I 0/3.3 V DC PGS1(L): On/Off
24 CAS1_QUANT1 I 0/3.3 V DC PGS1(U): On/Off
25 LIFT_MOT1_LOC I 0/3.3 V DC LM1 lock signal
K
26 LIFT_MOT2_LOC I 0/3.3 V DC LM2 lock signal
K
27 CURRENT_SIG I 0/3.3 V DC Current signal
28 V-FEED_CL O 0/24 V DC PCCL: On/Off
29 COVER_OPEN I 0/3.3 V DC RLCSW: On/Off
30 FEED2_SENS I 0/3.3 V DC PFPCS1: On/Off
31 CAS1_P0 I 0/3.3 V DC FS1: On/Off
32 CAS1_LIFT_UP I 0/3.3 V DC LS1: On/Off
33 GND - - Ground
34 CAS1_EMPTY I 0/3.3 V DC PS1: On/Off
35 PICK_SOL1_RET O 0/24 V DC PUSOL1: On/Off (RET)
36 PICK_SOL1_REM O 0/24 V DC PUSOL1: On/Off (ACT)
37 CAS2_P0 I 0/3.3 V DC FS2: On/Off
38 CAS2_LIFT_UP I 0/3.3 V DC LS2: On/Off
39 CAS2_EMPTY I 0/3.3 V DC PS2: On/Off
42 GND - - Ground
43 REG_SENS I 0/3.3 V DC RS: On/Off
44 FEED1_SENS I 0/3.3 V DC PCS: On/Off
45 BEND_SENS I 0/3.3 V DC RDS: On/Off
46 MID_MOT_PH O 0/3.3 V DC MM control signal
47 MID_MOT_REM( O 0/3.3 V DC MM/MCL: On/Off
ROL_CL)
48 MID_MOT_CLK O 0/3.3 V DC (pulse) MM clock signal
49 MID_MOT_PD O 0/3.3 V DC MM control signal
50 ASIST_CL1 O 0/24 V DC ASCL1: On/Off
2-3-15
2LK/2LN/2LM/2LC

Connected to 2 M_TEMP - - Not used
feed PWB 1
3 LOOP_SENS I 0/3.3 V DC LPS: On/Off
4 GND - - Ground
5 EDGE_FAN_H O 0/24 V DC FUFM: On/Off
6 DU1_MOT_PD O 0/3.3 V DC DUM1 control signal
7 DU1_MOT_CLK O 0/3.3 V DC (pulse) DUM1 clock signal
8 DU1_MOT_REM( O 0/3.3 V DC DUM1/DUCL1: On/Off
CL_H)
9 GND - - Ground
10 EXIT_FAN O 0/24 V DC EFM: On/Off
11 DU_ENTER_SEN I 0/3.3 V DC DUS1: On/Off
S
12 TCON_SET - - Not used
13 GND - - Ground
14 TRANS_MOT_RE O 0/3.3 V DC TRCM: On/Off
M
15 TRANS_MOT_CL O 0/3.3 V DC (pulse) TRCM clock signal
K
16 TRANS_MOT_RD I 0/3.3 V DC TRCM ready signal
Y
17 TRANS_MOT_DI O 0/3.3 V DC TRCM drive switch signal
R
18 TRANS_MOT_BR O 0/3.3 V DC TRCM break signal
K
19 GND - - Ground
20 DRM_MOT_BK_R - - Not used
EM
DY
22 DRM_MOT_BK_D - - Not used
IR
23 DRM_MOT_BK_B - - Not used
RK
24 GND - - Ground
25 DLP_MOT_BK_R - - Not used
EM
26 DLP_MOT_BK_C - - Not used
LK
DY
2-3-16
2LK/2LN/2LM/2LC

YC5 28 DLP_MOT_BK_DI - - Not used
R
feed PWB 1 30 DRM_MOT_CLR_ - - Not used
REM
31 DRM_MOT_BK_C - - Not used
LR_CLK
32 DRM_MOT_CLR_ - - Not used
RDY
DIR
34 GND - - Ground
35 DLP_MOT_CLR_ - - Not used
REM
CLK
RDY
DIR
39 GND - - Ground
40 REG_MOT_PD O 0/3.3 V DC RM control signal
41 REG_MOT_CLK O 0/3.3 V DC (pulse) RM clock signal
42 REG_MOT_REM( O 0/3.3 V DC RM/RCL: On/Off
CL)
43 GND - - Ground
44 IH_PWB_FAN_L - - Not used
45 IH_PWB_FAN_H O 0/24 V DC IHFM: On/Off
46 IH_PWB_FAN_AL I 0/3.3 V DC IHFM alarm signal
M
47 POWER_OFF O 0/3.3 V DC Power off signal
48 DRM_HEAT_REM - - Not used
49 IH_PWB_FAN(U) - - Not used
_ALM
50 GND - - Ground
2-3-17
2LK/2LN/2LM/2LC

Connected to 2 JOB_SET I 0/3.3 V DC Job separator set signal
feed PWB 1
3 JOB_MOT_REM O 0/3.3 V DC JEM: On/Off
4 JOB_MOT_CLK O 0/3.3 V DC (pulse) JEM clock signal
5 JOB_MOT_DIR O 0/3.3 V DC JEM drive switch signal
6 JOB_OPEN_SEN I 0/3.3 V DC JOCS: On/Off
S
7 JOB_SOL_REM O 0/24 V DC JFSSOL: On/Off
8 GND - - Ground
9 MAIN_HEAT_RE - - Not used
M
10 SUB_HEAT_REM - - Not used
11 ZEROC - - Not used
12 FSR_RELAY O 0/3.3 V DC Fuser relay signal
13 PRESS_REM - - Not used
14 EXIT_REAR_FAN O 0/24 V DC ERFM: On/Off
_L
15 EXIT_REAR_FAN O 0/24 V DC ERFM: On/Off
_H
16 GND - - Ground
17 FSR_CL_REM - - Not used
18 FSR_MOT_REM O 0/3.3 V DC FUM: On/Off
19 FSR_MOT_CLK 0/3.3 V DC (pulse) FUM clock signal
20 FSR_MOT_RDY O 0/3.3 V DC FUM ready signal
21 FSR_MOT_DIR O 0/3.3 V DC FUM drive switch signal
22 FSR_MOT_BRK O 0/3.3 V DC FUM break signal
23 GND - - Ground
24 MPF_TABLE I 0/3.3 V DC MPTSW: On/Off
25 MPF_WID1 I 0/3.3 V DC MPPWSW: On/Off
28 MPF_LNG I 0/3.3 V DC MPPLSW: On/Off
29 GND - - Ground
30 MPF_PPR_SET I 0/3.3 V DC MPPS: On/Off
31 MPF_LIFT_UP I 0/3.3 V DC MPLS1: On/Off
32 MPF_LIFT_DOW I 0/3.3 V DC MPLS2: On/Off
N
33 MPF_JAM I 0/3.3 V DC MPFS: On/Off
2-3-18
2LK/2LN/2LM/2LC

YC6 34 MPF_CL O 0/24 V DC MPPFCL: On/Off
Connected to 35 MPF_LIF2 O 0/24 V DC MPLM: On/Off
feed PWB 1
36 MPF_LIFT1 O 0/24 V DC MPLM: On/Off
37 GND - - Ground
38 TC_MOT_LOCK - - Not used
39 TC_TONER_LED - - Not used
40 TC_TONER_FUL - - Not used
L
41 TC_TONER_VCO - - Not used
NT
42 INTER_LOCK - - Not used
43 DU2_PD O 0/3.3 V DC DUM2 control signal
44 DU2_CLK O 0/3.3 V DC (pulse) DUM2 clock signal
45 DU2_REM(CL_L O 0/3.3 V DC DUM2/DUCL2: On/Off
OW)
46 GND - - Ground
47 DU_OPEN I 0/3.3 V DC DUCSW: On/Off
48 DU_FAN - - Not used
49 PRESS_MOT_RE O 0/24 V DC TRRM: On/Off
M1
50 PRESS_MOT_RE O 0/24 V DC TRRM: On/Off
M2
51 PRESS_RLS_SE I 0/3.3 V DC TRRS: On/Off
NS
52 DU_SENS I 0/3.3 V DC DUS2: On/Off
53 BELT_JAM_SENS - - Not used
54 GND - - Ground
55 CLN_SOL_RET O 0/24 V DC CLSOL: On/Off (RET)
56 CLN_SOL_REM O 0/24 V DC CLSOL: On/Off (ACT)
57 REG_SENS_R_S I Analog IDS2 detection signal
58 REG_SENS_R_P I Analog IDS2 detection signal
59 REG_R_LED O Analog IDS2 control signal
60 GND - - Ground
61 REG_SENS_F_S I Analog IDS1 detection signal
62 REG_SENS_F_P I Analog IDS1 detection signal
63 REG_F_LED O Analog IDS1 control signal
64 GND - - Ground
2-3-19
2LK/2LN/2LM/2LC

Connected to 2 WTNR_SET - - Not used
front PWB
4 IH_CORE_SENS - - Not used
5 IH_CORE_MOT_ - - Not used
REM
6 IH_CORE_CLK - - Not used
7 WTNR_LED O 0/3.3 V DC (pulse) WTS1 LED emitter signal
8 IH_COIL_FAN_AL I 0/3.3 V DC CFM1 alarm signal
M
9 IH_COIL_FAN_H O 0/24 V DC CFM1: On/Off
10 IH_COIL_FAN_L O 0/24 V DC CFM1: On/Off
11 EXIT_FAN O 0/24 V DC EFFM: On/Off
12 CONTAIN_FAN - - Not used
13 JUNC_SOL_REM O 0/24 V DC FSSOL: On/Off (ACT)
14 JUNC_SOL_RET O 0/24 V DC FSSOL: On/Off (RET)
15 GND - - Ground
16 EXIT_PAPE_SEN I 0/3.3 V DC EFS: On/Off
S
17 EXIT_FEED_SEN I 0/3.3 V DC SBS: On/Off
S
18 SB_MOT_REM O 0/3.3 V DC EM: On/Off
19 SB_MOT_PH O 0/3.3 V DC EM control signal
20 SB_MOT_CLK O 0/3.3 V DC (pulse) EM clock signal
21 SB_MOT_PD O 0/3.3 V DC EM control signal
22 SB_MOT_DIR O 0/3.3 V DC EM drive switch signal
23 GND - - Ground
24 DLP_FAN_ Bk_H O 0/24 V DC DEVFM2: On/Off
25 DLP_FAN_ Bk_L O 0/24 V DC DEVFM2: On/Off
26 DLP_FAN_CLR_ O 0/24 V DC DEVFM1: On/Off
H
27 DLP_FAN_CLR_L O 0/24 V DC DEVFM1: On/Off
28 WTNR_SET I Analog WTS2 detection signal
29 WTNR_NEAR I Analog WTS2 detection signal
30 WTNR_VCONT O 0/3.3 V DC WTS2 control signal
31 GND - - Ground
32 ROT_MOT_REM - - Not used
33 ROT_MOT_CLK - - Not used
2-3-20
2LK/2LN/2LM/2LC

YC7 34 ROT_MOT_PD - - Not used
Connected to 35 ROT_MOT_DIR - - Not used
front PWB
36 ROT_HP_SENS - - Not used
37 THOP_MOT_Bk_ - - Not used
REM
38 THOP_MOT_M_R - - Not used
EM
39 THOP_MOT_C_R - - Not used
EM
40 THOP_MOT_Y_R - - Not used
EM
41 GND - - Ground
42 ENCODE_ Bk - - Not used
43 ENCODE_M - - Not used
44 ENCODE_C - - Not used
45 ENCODE_Y - - Not used
46 THOP_ Bk - - Not used
47 THOP_M - - Not used
48 THOP_C - - Not used
49 THOP_Y - - Not used
50 GND - - Ground
Connected to 2 SGND - - Ground
high voltage
3 SP_CNT O Analog Separation bias control voltage
PWB 2
4 T2_CNT O Analog Secondary transfer bias control volt-
age
5 SP_REM O 0/3.3 V DC Separation bias: On/Off
6 T_REM O 0/3.3 V DC Secondary transfer bias: On/Off
7 FB_CNT O 0/3.3 V DC Primary transfer cleaning bias: On/Off
8 T1_CNT_Bk O Analog Primary transfer bias K control volt-
age
9 T1_CNT_M O Analog Primary transfer bias M control volt-
age
10 T1_CNT_C O Analog Primary transfer bias C control volt-
age
11 T1_CNT_Y O Analog Primary transfer bias Y control volt-
age
12 T1_CLR_OFF_RE O 0/3.3 V DC Primary transfer control signal
M
2-3-21
2LK/2LN/2LM/2LC

YC9 1 MOT_CLK O 0/3.3 V DC (pulse) MCPWB clock signal
Connected to 2 MOT_SDO O 0/3.3 V DC (pulse) MCPWB serial communication data
motor con- signal
trol PWB 3 MOT_SEL O 0/3.3 V DC MCPWB select signal
4 MOT_SDI I 0/3.3 V DC (pulse) MCPWB serial communication data
signal
5 MOT_RDY I 0/3.3 V DC MCPWB ready signal
6 EMERGENCY O 0/3.3 V DC MCPWB control signal
7 BLT_SPEED O 0/3.3 V DC TBLS: On/Off
8 BLT_INDEX - - Not used
9 DRM_INDEX_BK O 0/3.3 V DC DRM-K control signal
10 DRM_INDEX_M O 0/3.3 V DC DRM-M control signal
11 DRM_INDEX_C O 0/3.3 V DC DRM-C control signal
12 DRM_INDEX_Y O 0/3.3 V DC DRM-Y control signal
13 GND - - Ground
14 GND - - Ground
15 +5V O 5 V DC 5 V DC power to MCPWB
16 +5V O 5 V DC 5 V DC power to MCPWB
17 BLT_BRAKE - - Not used
18 BLT_VM - - Not used
19 BLT_REM - - Not used
20 MOT_DATA_SET O 0/3.3 V DC MCPWB control signal
21 DRM_ON O 0/3.3 V DC MCPWB control signal
22 BLT_FG - - Not used
Connected to 2 DRM_INDEX_Bk I 0/3.3 V DC DRM-K control signal
front PWB
3 ERS_Bk O 0/24 V DC CL-K: On/Off
4 TPD_Bk_1 I Analog DEVPWB-K detection signal
5 DLP_VCONT_Bk O 0/3.3 V DC DEVPWB-K control signal
_1
6 TPD_TEMP_Bk I Analog Developer thermistor K detection sig-
nal
7 GND - - Ground
8 DRM_INDEX_M I 0/3.3 V DC DRM-M control signal
9 ERS_M O 0/24 V DC CL-M: On/Off
10 TPD_M_1 I Analog DEVPWB-M detection signal
11 DLP_VCONT_M_ O 0/3.3 V DC DEVPWB-M control signal
1
2-3-22
2LK/2LN/2LM/2LC

YC10 12 TPD_TEMP_M I Analog Developer thermistor M detection sig-
nal
front PWB 14 DRM_INDEX_C I 0/3.3 V DC DRM-C control signal
15 ERS_C O 0/24 V DC CL-C: On/Off
16 TPD_C_1 I Analog DEVPWB-C detection signal
17 DLP_VCONT_C_ O 0/3.3 V DC DEVPWB-C control signal
1
18 TPD_TEMP_C I Analog Developer thermistor C detection sig-
nal
19 GND - - Ground
20 TN_CLK O 0/3.3 V DC (pulse) Clock signal
21 GND - - Ground
22 EEP_SCL1 O 0/3.3 V DC (pulse) EEPROM clock signal
23 GND - - Ground
24 EEP_SDA1 I/O 0/3.3 V DC (pulse) EEPROM data signal
25 GND - - Ground
26 TPD_Y_1 I Analog DEVPWB-Y detection signal
27 DLP_VCONT_Y_ O 0/3.3 V DC DEVPWB-Y control signal
1
28 TPD_TEMP_Y I Analog Developer thermistor Y detection sig-
nal
29 ERS_Y O 0/24 V DC CL-Y: On/Off
30 DRM_INDEX_Y I 0/3.3 V DC DRM-Y control signal
31 FRONT_OPEN I 0/3.3 V DC FRCSW: On/Off
32 GND - - Ground
33 I2C_SCL O 0/3.3 V DC (pulse) EEPROM clock signal
34 GND - - Ground
35 I2C_SDA I/O 0/3.3 V DC (pulse) EEPROM data signal
36 GND - - Ground
37 LSU_FAN_REM O 0/24 V DC LSUFM: On/Off
38 CLEAN_MOT_LO I 0/3.3 V DC WTM lock signal
CK
39 CLEAN_MOT_RE O 0/24 V DC WTM: On/Off
M
40 GND - - Ground
2-3-23
2LK/2LN/2LM/2LC

Connected to 2 DATA_2PBK(LVD O 0/3.3 V DC (pulse) Video data signal K (P)
LSU relay S)
PWB 3 DATA_2NBK(LVD O 0/3.3 V DC (pulse) Video data signal K (N)
S)
4 SGND - - Ground
5 GAIN_FIX_BK O 0/3.3 V DC APCPWB-K control signal
6 PARA_SIG_P2_B O 0/3.3 V DC APCPWB-K control signal
K
K
K
9 INT_ST_1_BK O 0/3.3 V DC APCPWB-K control signal
10 INT_ST_2_BK O 0/3.3 V DC APCPWB-K control signal
11 PARA_SIG_P3_2 O 0/3.3 V DC APCPWB-K control signal
BK
12 SGND - - Ground
13 DATA_4PBK(LVD O 0/3.3 V DC (pulse) Video data signal K (P)
S)
14 DATA_4NBK(LVD O 0/3.3 V DC (pulse) Video data signal K (N)
S)
15 SGND - - Ground
S)
S)
18 SGND - - Ground
19 DATA_2P_M(LVD O 0/3.3 V DC (pulse) Video data signal M (P)
S)
20 DATA_2N_M(LVD O 0/3.3 V DC (pulse) Video data signal M (N)
S)
21 SGND - - Ground
22 GAIN_FIX_M O 0/3.3 V DC APCPWB-M control signal
23 PALA_STG_P2_M O 0/3.3 V DC APCPWB-M control signal
26 INT_ST_M O 0/3.3 V DC APCPWB-M control signal
27 SGND - - Ground
28 DATA_2P_C(LVD O 0/3.3 V DC (pulse) Video data signal C (P)
S)
2-3-24
2LK/2LN/2LM/2LC

YC11 29 DATA_2N_C(LVD O 0/3.3 V DC (pulse) Video data signal C (N)
S)
LSU relay 31 GAIN_FIX_C O 0/3.3 V DC APCPWB-C control signal
PWB
32 PALA_STG_P2_C O 0/3.3 V DC APCPWB-C control signal
35 INT_ST_C O 0/3.3 V DC APCPWB-C control signal
36 SGND - - Ground
37 DATA_2P_Y(LVD O 0/3.3 V DC (pulse) Video data signal Y (P)
S)
38 DATA_2N_Y(LVD O 0/3.3 V DC (pulse) Video data signal Y (N)
S)
39 SGND - - Ground
40 GAIN_FIX_Y O 0/3.3 V DC APCPWB-Y control signal
41 PALA_STG_P2_Y O 0/3.3 V DC APCPWB-Y control signal
44 INT_ST_Y O 0/3.3 V DC APCPWB-Y control signal
45 SGND - - Ground
46 EEPROM_CS_1_ I/O 0/3.3 V DC (pulse) APCPWB-K EEPROM data signal
BK
47 IDD_CS_1_BK O 0/3.3 V DC APCPWB-K control signal
48 EEPROM_CS_2_ I/O 0/3.3 V DC (pulse) APCPWB-K EEPROM data signal
BK
49 IDD_CS_2_BK O 0/3.3 V DC APCPWB-K control signal
50 EEPROM_CS_M I/O 0/3.3 V DC (pulse) APCPWB-M EEPROM data signal
51 IDD_CS_M O 0/3.3 V DC APCPWB-M control signal
52 EEPROM_CS_C I/O 0/3.3 V DC (pulse) APCPWB-C EEPROM data signal
53 IDD_CS_C O 0/3.3 V DC APCPWB-C control signal
54 EEPROM_CS_Y I/O 0/3.3 V DC (pulse) APCPWB-Y EEPROM data signal
55 IDD_CS_Y O 0/3.3 V DC APCPWB-Y control signal
56 SGND - - Ground
57 MSET_N O 0/3.3 V DC Control signal
58 SGND - - Ground
59 SDO O 0/3.3 V DC (pulse) Serial communication data signal
60 SGND - - Ground
2-3-25
2LK/2LN/2LM/2LC

YC11 61 SDI I 0/3.3 V DC (pulse) Serial communication data signal
LSU relay
63 CLK O 0/3.3 V DC (pulse) Clock signal
PWB
64 SGND - - Ground
YC12 1 CLK_BK O 0/3.3 V DC (pulse) PM-K clock signal
Connected to 2 LOCK_BK I 0/3.3 V DC PM-K lock signal
LSU relay
3 REM_BK O 0/24 V DC PM-K: On/Off
PWB
4 SGND - - Ground
S)
S)
7 SGND - - Ground
8 SDCLK_BK O 0/3.3 V DC (pulse) APCPWB-K clock signal
9 SGND - - Ground
K
K
12 CUALM_BK I 0/3.3 V DC APCPWB-K alarm signal
13 LSU_TH_BK I Analog LSU thermistor K detection signal
14 BD_BK I 0/3.3 V DC (pulse) Horizontal synchronization signal K
15 SGND - - Ground
16 CLK_M O 0/3.3 V DC (pulse) PM-M clock signal
17 LOCK_M I 0/3.3 V DC PM-M lock signal
18 REM_M O 0/24 V DC PM-M: On/Off
19 SGND - - Ground
S)
S)
22 SGND - - Ground
23 SDCLK_M O 0/3.3 V DC (pulse) APCPWB-M clock signal
24 SGND - - Ground
25 PARA_SIG_P4_M O 0/3.3 V DC APCPWB-M control signal
26 PARA_SIG_P3_M O 0/3.3 V DC APCPWB-M control signal
27 CUALM_M I 0/3.3 V DC APCPWB-M alarm signal
28 LSU_TH_M I Analog LSU thermistor M detection signal
2-3-26
2LK/2LN/2LM/2LC

YC12 29 BD_M I 0/3.3 V DC (pulse) Horizontal synchronization signal M
LSU relay
31 CLK_C O 0/3.3 V DC (pulse) PM-C clock signal
PWB
32 LOCK_C I 0/3.3 V DC PM-C lock signal
33 REM_C O 0/24 V DC PM-C: On/Off
34 SGND - - Ground
S)
36 DATA_1N_C(LVD O 0/3.3 V DC (pulse) Video data signal C (N)
S)
37 SGND - - Ground
38 SDCLK_C O 0/3.3 V DC (pulse) APCPWB-C clock signal
39 SGND - - Ground
40 PARA_SIG_P4_C O 0/3.3 V DC APCPWB-C control signal
41 PARA_SIG_P3_C O 0/3.3 V DC APCPWB-C control signal
42 CUALM_C I 0/3.3 V DC APCPWB-C alarm signal
43 LSU_TH_C I Analog LSU thermistor C detection signal
44 BD_C I 0/3.3 V DC (pulse) Horizontal synchronization signal C
45 SGND - - Ground
46 CLK_Y O 0/3.3 V DC (pulse) PM-Y clock signal
47 LOCK_Y I 0/3.3 V DC PM-Y lock signal
48 REM_Y O 0/24 V DC PM-Y: On/Off
49 SGND - - Ground
S)
S)
52 SGND - - Ground
53 SDCLK_Y O 0/3.3 V DC (pulse) APCPWB-Y clock signal
54 SGND - - Ground
55 PARA_SIG_P4_Y O 0/3.3 V DC APCPWB-Y control signal
56 PARA_SIG_P3_Y O 0/3.3 V DC APCPWB-Y control signal
57 CUALM_Y I 0/3.3 V DC APCPWB-Y alarm signal
58 LSU_TH_Y I Analog LSU thermistor Y detection signal
59 BD_Y I 0/3.3 V DC (pulse) Horizontal synchronization signal Y
60 SGND - - Ground
2-3-27
2LK/2LN/2LM/2LC

feed PWB 1
3 3.3V3 I 3.3 V DC 3.3 V DC power from FPWB1
4 3.3V2 I 3.3 V DC 3.3 V DC power from FPWB1
Connected to 2 AC_MAIN_CLK O 0/3.3 V DC (pulse) AC charger roller Y clock signal
high voltage
3 DC_MAIN_REM O 0/3.3 V DC DC main charger Y: On/Off
PWB 1
4 DC_MAIN_CNT_ O PWM DC charger roller Y control signal
Y
5 MAIN_IDC_Y O PWM DC charger roller Y control signal
6 AC_SLV_CLK_Y O 0/3.3 V DC (pulse) AC sleeve bias Y clock signal
7 DC_SLV_CNT_Y O PWM DC sleeve bias Y control voltage
8 DC_MAG_CNT_Y O PWM DC magnet bias Y control voltage
9 AC_SLV_CNT_Y O PWM AC sleeve bias Y control voltage
10 AC_MAIN_CNT_ O PWM AC charger roller Y control signal
Y
11 DISCHARGE_Y I PWM Main charger Y control signal
12 AC_MAG_CNT_Y O 0/3.3 V DC (pulse) AC magnet bias Y control voltage
13 AC_MAG_CLK_Y O 0/3.3 V DC (pulse) AC magnet bias Y clock signal
14 DC_REC_CNT O PWM DC bias Y control voltage
15 N.C - - Not used
16 DC_REC_REM O PWM DC bias C control voltage
17 AC_MAG_CLK_C O 0/3.3 V DC (pulse) AC magnet bias C clock signal
18 AC_MAG_CNT_C O 0/3.3 V DC (pulse) AC magnet bias C control voltage
19 DISCHARGE_C I PWM Main charger C control signal
20 AC_MAIN_CNT_ O PWM AC charger roller C control signal
C
21 AC_SLV_CNT_C O PWM AC sleeve bias C control voltage
22 DC_MAG_CNT_C O PWM DC magnet bias C control voltage
23 DC_SLV_CNT_C O PWM DC sleeve bias C control voltage
24 AC_SLV_CLK_C O 0/3.3 V DC (pulse) AC sleeve bias C clock signal
25 DC_MAG_REM O 0/3.3 V DC DC main charger C: On/Off
26 MAIN_IDC_C O PWM DC charger roller C control signal
27 DC_MAIN_CNT_ O PWM DC charger roller C control signal
C
28 SGND - - Ground
2-3-28
2LK/2LN/2LM/2LC

Connected to 2 DC_MAIN_CNT_ O PWM DC charger roller Y control signal
high voltage M
PWB 1 3 MAIN_IDC_M O PWM DC charger roller M control signal
4 AC_SLV_CLK_M O 0/3.3 V DC (pulse) AC sleeve bias M clock signal
5 DC_SLV_CNT_M O PWM DC sleeve bias M control voltage
6 DC_MAG_CNT_ O PWM DC magnet bias M control voltage
M
7 AC_SLV_CNT_M O PWM AC sleeve bias M control voltage
8 AC_MAIN_CNT_ O PWM AC charger roller M control signal
M
9 DISCHARGE_M I PWM Main charger M control signal
10 AC_MAG_CNT_M O 0/3.3 V DC (pulse) AC magnet bias M control voltage
11 AC_MAG_CLK_M O 0/3.3 V DC (pulse) AC magnet bias M clock signal
12 AC_MAG_CLK_B O PWM DC charger roller K control signal
k
13 AC_MAG_CNT_B O PWM DC charger roller K control signal
k
14 DISCHARGE_Bk I PWM Main charger K control signal
15 AC_SLV_CNT_Bk O 0/3.3 V DC (pulse) AC sleeve bias K clock signal
16 DC_MAG_CNT_B O PWM DC sleeve bias K control voltage
k
17 DC_SLV_CNT_Bk O PWM DC magnet bias K control voltage
18 AC_SLV_CLK_Bk O PWM AC sleeve bias K control voltage
19 AC_MAIN_CNT_ O PWM AC charger roller K control signal
Bk
20 MAIN_IDC_Bk O PWM DC charger roller K control signal
21 DC_MAIN_CNT_ O PWM DC charger roller K control signal
Bk
22 SGND - - Ground
YC18 1 DF_CLK O 0/3.3 V DC (pulse) DFMPWB clock signal
Connected to 2 DF_SDO O 0/3.3 V DC (pulse) DFMPWB serial communication data
1000-sheet/ signal
4000-sheet 3 DF_SEL O 0/3.3 V DC DFMPWB select signal
finisher
4 DF_SDI O 0/3.3 V DC (pulse) DFMPWB serial communication data
signal
5 DF_RDY I 0/3.3 V DC DFMPWB ready signal
6 DF_DET O 0/3.3 V DC DFMPWB detection signal
7 GND - - Ground
2-3-29
2LK/2LN/2LM/2LC

YC19 A1 PF_CLK O 0/3.3 V DC (pulse) PFMPWB clock signal
Connected to A2 PF_SDO O 0/3.3 V DC (pulse) PFMPWB serial communication data
paper feeder/ signal
large capac- A3 PF_SEL O 0/3.3 V DC PFMPWB select signal
ity feeder,
toner fan A4 PF_SDI I 0/3.3 V DC (pulse) PFMPWB serial communication data
motor 1/2, signal
and belt fan A5 PF_RDY I 0/3.3 V DC PFMPWB ready signal
motor 1/2
A6 PF_PAUSE O 0/3.3 V DC PFMPWB pause signal
A7 PF_CAS1_OPEN I 0/3.3 V DC PFMPWB control signal
A8 PF_CAS2_OPEN I 0/3.3 V DC PFMPWB control signal
A9 +3.3V4 O 3.3 V DC 3.3 V DC power to PFMPWB
A10 GND - - Ground
A11 GND - - Ground
A12 TN_FAN1 O 0/24 V DC TFM1: On/Off
A13 +24V1 O 24 V DC 24 V DC power to TFM1
A14 TN_FAN2 O 0/24 V DC TFM2: On/Off
A15 +24V1 O 24 V DC 24 V DC power to TFM2
A16 LVU_FAN1 - - Not used
A17 +24V1 - - Not used
A18 LVU_FAN2 - - Not used
A19 +24V1 - - Not used
B1 SIDE_CLK O 0/3.3 V DC (pulse) PFMPWB clock signal (side)
B2 SIDE_SDO O 0/3.3 V DC (pulse) PFMPWB serial communication data
signal (side)
B3 SIDE_SEL O 0/3.3 V DC PFMPWB select signal (side)
B4 SIDE_SDI I 0/3.3 V DC (pulse) PFMPWB serial communication data
signal (side)
B5 SIDE_RDY I 0/3.3 V DC PFMPWB ready signal (side)
B6 SIDE_PAUSE O 0/3.3 V DC PFMPWB pause signal (side)
B7 TANDEM_CAS1O I 0/3.3 V DC PFMPWB control signal (side)
PEN
B8 TANDEM_CAS2O I 0/3.3 V DC PFMPWB control signal (side)
PEN
B9 SIDE_MULTI_OP O 0/3.3 V DC PFMPWB control signal (side)
EN
B10 +3.3V4 O 3.3 V DC 3.3 V DC power to PFMPWB (side)
B11 GND I 0/3.3 V DC (pulse) Serial communication data signal
input
B12 +24V1 O 24 V DC BLFM124 V DC power to BLFM1
2-3-30
2LK/2LN/2LM/2LC

YC19 B13 BELT_FAN1 O 0/24 V DC BLFM1: On/Off
Connected to B14 +24V1 O 24 V DC 24 V DC power to BLFM2
paper feeder/
B15 BELT_FAN2 O 0/24 V DC BLFM2: On/Off
large capac-
ity feeder, B16 DLP_FAN1 - - Not used
toner fan B17 +24V1 - - Not used
motor 1/2,
B18 DLP_FAN2 - - Not used
and belt fan
motor 1/2 B19 +24V1 - - Not used
YC20 1 DECAL_HP_SEN - - Not used
S
Connected to 2 GUIDE_REM - - Not used
bridge unit
3 GUIDE_CLK - - Not used
4 GUIDE_PD - - Not used
5 GUIDE_DIR - - Not used
6 DECAL_REM - - Not used
7 DECAL_PH - - Not used
8 DECAL_CLK - - Not used
9 DECAL_PD - - Not used
10 DECAL_DIR - - Not used
11 +24V O 24 V DC 24 V DC power to BRSOL
12 EXIT_SOL_REM O 0/24 V DC BRSOL: On/Off (ACT)
13 EXIT_SOL_RET O 0/24 V DC BRSOL: On/Off (RET)
14 GND - - Ground
15 EXIT_COV_OPE I 0/3.3 V DC BRECSW: On/Off
N
16 GND - - Ground
17 EXIT_SENS I 0/3.3 V DC BRES: On/Off
18 +5V O 5 V DC 5 V DC power to BRES
19 N.C - - Not used
20 BRIDGE2 REM O 0/3.3 V DC BRCM2: On/Off
21 BRIDGE2 PH O 0/3.3 V DC BRCM2 control signal
22 BRIDGE2 CLK O 0/3.3 V DC (pulse) BRCM2 clock signal
23 BRIDGE2 PD O 0/3.3 V DC BRCM2 control signal
24 BRIDGE2 DIR O 0/3.3 V DC BRCM2 drive switch signal
25 BRIDGE1 REM O 0/3.3 V DC BRCM2: On/Off
26 BRIDGE1 PH O 0/3.3 V DC BRCM1 control signal
27 BRIDGE1 CLK O 0/3.3 V DC (pulse) BRCM1 clock signal
28 BRIDGE1 PD O 0/3.3 V DC BRCM1 control signal
2-3-31
2LK/2LN/2LM/2LC

YC20 29 BRIDGE1 DIR O 0/3.3 V DC BRCM1 drive switch signal
Connected to 30 BRIDGE_SENS 2 I 0/3.3 V DC BRCS2: On/Off
bridge unit
31 BRIDGE_OPEN I 0/3.3 V DC BRCSW: On/Off
32 BRIDGE_SENS 1 I 0/3.3 V DC BRCS1: On/Off
33 GND - - Ground
34 5V O 5 V DC 5 V DC power to BRPWB
35 GND - - Ground
36 GND - - Ground
37 +24V1 O 24 V DC 24 V DC power to BRPWB
38 +24V1 O 24 V DC 24 V DC power to BRPWB
YC22 1 LVU_FAN O 0/24 V DC PSFM: On/Off
Connected to 2 +24V1 O 24 V DC 24 V DC power to PSFM
power source
fan motor
YC23 1 +24V O 24 V DC 24 V DC power to coin vender
coin vender
3 GND - - Ground
4 COIN_EN I 0/3.3 V DC Coin vender enable signal
5 FGND - - Ground
6 FEED_COUNT O 0/3.3 V DC Coin vender control signal
7 EJECT_COUNT O 0/3.3 V DC Coin vender control signal
8 COPYING_SIG O 0/3.3 V DC Coin vender control signal
9 TXD_COIN O 0/3.3 V DC (pulse) Serial communication data signal
10 GND - - Serial communication data signal
11 RXD_COIN I 0/3.3 V DC (pulse) MCL: On/Off
12 GND - - Ground
Connected to 2 DC1_SET I 0/3.3 V DC Key counter set signal
key counter
3 DC1_COUNT O 0/3.3 V DC Key counter count signal
4 +24V 1 O 24 V DC 24 V DC power to key card
2-3-32
2LK/2LN/2LM/2LC

YC25 A1 +5V O 5 V DC 5 V DC power to key card
Connected to A2 +5V O 5 V DC 5 V DC power to key card
key card
A3 +5V O 5 V DC 5 V DC power to key card
A9 COPY_ENABLE I 0/3.3 V DC Key card enable signal
B1 KEY7 O 0/3.3 V DC Key card control signal
B9 GND - - Ground
B10 COUNT O 0/3.3 V DC Key card count signal
YC26 A1 EDGE_FAN_ALM I 0/3.3 V DC FURFM alarm signal
Connected to A2 EDGE_FAN O 0/24 V DC FURFM: On/Off
fuser unit and
A3 +24V1 O 24 V DC 24 V DC power to FURFM
fuser IH PWB
A4 EDGE_FAN_ALM I 0/3.3 V DC FUFFM alarm signal
A5 EDGE_FAN O 0/24 V DC FUFFM: On/Off
A6 +24V1 O 24 V DC 24 V DC power to FUFFM
A7 FSR_FAN_ALM I 0/3.3 V DC CFM2 alarm signal
A8 FSR_FAN O 0/24 V DC CFM2: On/Off
A9 +24V1 O 24 V DC 24 V DC power to CFM2
A10 FSR_RLS_DR_C O 0/24 V DC FURM: On/Off (CCW)
CW
A11 FSR_RLS_DR_C O 0/24 V DC FURM: On/Off (CW)
W
A12 GND - - Ground
A13 FSR_SIZE_SENS I 0/3.3 V DC FUES: On/Off
A14 +5V O 5 V DC 5 V DC power to FUES
A15 GND - - Ground
2-3-33
2LK/2LN/2LM/2LC

YC26 A16 FSR_RLS_SENS I 0/3.3 V DC FURS: On/Off
Connected to A17 +5V O 5 V DC 5 V DC power to FURS
fuser unit and
A18 GND - - Ground
fuser IH PWB
A19 FSR_BLT_PLS I 0/3.3 V DC FUBLS: On/Off
A20 +5V O 5 V DC 5 V DC power to FUBLS
B1 PRESS_HEART_ - - Not used
REM
B2 IH_RXD I 0/3.3 V DC (pulse) Serial communication data signal
B3 IH_TXD O 0/3.3 V DC (pulse) Serial communication data signal
B4 ROTATION O 0/3.3 V DC FIH control signal
B5 IH_HEAT_REM O 0/3.3 V DC FIH: On/Off
B6 +3.3V2 O 3.3 V DC 5 V DC power to FIH
B7 GND - - Ground
B8 GND - - Ground
B9 PRESS_TH I Analog FTH4 detection signal
B10 GND - - Ground
B11 EDGE_TH I Analog FTH3 detection signal
B12 GND - - Ground
B13 GUIDE_TH1 - - Not used
B14 GND - - Ground
B15 GUIDE_TH2 I Analog FTH2 detection signal
B16 MAIN_TH2 I Analog FTH1 detection signal
B17 MAIN_TH1 I Analog FTH1 detection signal
B18 GND - - Ground
B19 +24V1 O 24 V DC 24 V DC power to BRFM
B20 BRIDGE_FAN O 0/24 V DC BRFM: On/Off
YC27 1 EEP_SDA2 I/O 0/3.3 V DC (pulse) EEPROM data signal
RFID PWB,
3 EEP_SCL2 I 0/3.3 V DC (pulse) EEPROM clock signal
toner motor
K/M/C/Y and 4 3.3V2 O 3.3 V DC 3.3 V DC power to RFPWB
screw sen- 5 +24V1 O 24 V DC 24 V DC power to TM-Y
sor K/M/C/Y
6 TMOT_Y_DR O 0/24 V DC TM-Y: On/Off
7 +24V1 O 24 V DC 24 V DC power to TM-C
8 TMOT_C_DR O 0/24 V DC TM-C: On/Off
9 +24V1 O 24 V DC 24 V DC power to TM-M
10 TMOT_M_DR O 0/24 V DC TM-M: On/Off
11 +24V1 I 24 V DC 24 V DC power to TM-K
2-3-34
2LK/2LN/2LM/2LC

YC27 12 TMOT_Bk_DR O 0/24 V DC TM-K: On/Off
RFID PWB,
14 ENCODE_Y I 0/3.3 V DC SRS-Y: On/Off
toner motor
K/M/C/Y and 15 +5V O 5 V DC 24 V DC power to SRS-Y
screw sen- 16 GND - - Ground
sor K/M/C/Y
17 ENCODE_C I 0/3.3 V DC SRS-C: On/Off
18 +5V O 5 V DC 24 V DC power to SRS-C
19 GND - - Ground
20 ENCODE_M I 0/3.3 V DC SRS-M: On/Off
21 +5V O 5 V DC 24 V DC power to SRS-M
22 GND - - Ground
23 ENCODE_K I 0/3.3 V DC SRS-K: On/Off
24 +5V O 5 V DC 24 V DC power to SRS-K
YC46 1 HSYNC_AN I 0/3.3 V DC (pulse) Image control signal
Connected to 2 HSYNC_AP I 0/3.3 V DC (pulse) Image control signal
main PWB
3 HSYNC_BN I 0/3.3 V DC (pulse) Image control signal
4 HSYNC_BP I 0/3.3 V DC (pulse) Image control signal
5 HSYNC_CN I 0/3.3 V DC (pulse) Image control signal
6 HSYNC_CP I 0/3.3 V DC (pulse) Image control signal
7 HSYNC_DN I 0/3.3 V DC (pulse) Image control signal
8 HSYNC_DP I 0/3.3 V DC (pulse) Image control signal
9 VSYNC_AN I 0/3.3 V DC (pulse) Image control signal
10 VSYNC_AP I 0/3.3 V DC (pulse) Image control signal
11 VSYNC_BN I 0/3.3 V DC (pulse) Image control signal
12 VSYNC_BP I 0/3.3 V DC (pulse) Image control signal
13 VSYNC_CN I 0/3.3 V DC (pulse) Image control signal
14 VSYNC_CP I 0/3.3 V DC (pulse) Image control signal
15 VSYNC_DN I 0/3.3 V DC (pulse) Image control signal
16 VSYNC_DP I 0/3.3 V DC (pulse) Image control signal
17 SGND - - Ground
18 TCLKP I 0/3.3 V DC (pulse) Clock signal
19 TCLKN I 0/3.3 V DC (pulse) Clock signal
20 SGND - - Ground
21 TCP I 0/3.3 V DC (pulse) Image control signal
22 TCN I 0/3.3 V DC (pulse) Image control signal
23 SGND - - Ground
2-3-35
2LK/2LN/2LM/2LC

YC46 24 TBP I 0/3.3 V DC (pulse) Image control signal
Connected to 25 TBN I 0/3.3 V DC (pulse) Image control signal
main PWB
26 SGND - - Ground
27 TAP I 0/3.3 V DC (pulse) Image control signal
28 TAN I 0/3.3 V DC (pulse) Image control signal
29 SGND - - Ground
30 SLEEP I 0/3.3 V DC Sleep signal
31 HLD_ENG I 0/3.3 V DC Engine hold signal
32 NC - - Not used
33 SGND - - Ground
34 EG IRN I 0/3.3 V DC Engine interrupt signal
35 EG SO O 0/3.3 V DC (pulse) Serial communication data signal
36 EG SBSY I 0/3.3 V DC Engine busy signal
37 EG SDIR I 0/3.3 V DC Engine communication direction sig-
nal
38 EG_SI I 0/3.3 V DC (pulse) Serial communication data signal
39 EG_SCLK I 0/3.3 V DC (pulse) Engine lock signal
40 SGND - - Ground
YC47 1 NC - - Not used
fiery relay 3 NC - - Not used
PWB
4 NC - - Not used
5 NC - - Not used
6 NC - - Not used
7 NC - - Not used
8 NC - - Not used
9 NC - - Not used
10 NC - - Not used
11 NC - - Not used
12 SGND - - Ground
13 CH1_N O 0/3.3 V DC (pulse) Image control signal
14 CH1_P O 0/3.3 V DC (pulse) Image control signal
15 SGND - - Ground
17 CH2_P O 0/3.3 V DC (pulse) Image control signal
18 SGND - - Ground
2-3-36
2LK/2LN/2LM/2LC

YC47 20 CH3_P O 0/3.3 V DC (pulse) Image control signal
fiery relay
22 VCLK_N O 0/3.3 V DC (pulse) Clock signal
PWB
23 VCLK_P O 0/3.3 V DC (pulse) Clock signal
24 SGND - - Ground
25 VSYNC_DP O 0/3.3 V DC (pulse) Image control signal
26 VSYNC_DN O 0/3.3 V DC (pulse) Image control signal
27 VSYNC_CP O 0/3.3 V DC (pulse) Image control signal
28 VSYNC_CN O 0/3.3 V DC (pulse) Image control signal
29 VSYNC_BP O 0/3.3 V DC (pulse) Image control signal
30 VSYNC_BN O 0/3.3 V DC (pulse) Image control signal
31 VSYNC_AP O 0/3.3 V DC (pulse) Image control signal
32 VSYNC_AN O 0/3.3 V DC (pulse) Image control signal
33 HSYNC_DP O 0/3.3 V DC (pulse) Image control signal
34 HSYNC_DN O 0/3.3 V DC (pulse) Image control signal
35 HSYNC_CP O 0/3.3 V DC (pulse) Image control signal
36 HSYNC_CN O 0/3.3 V DC (pulse) Image control signal
37 HSYNC_BP O 0/3.3 V DC (pulse) Image control signal
38 HSYNC_BN O 0/3.3 V DC (pulse) Image control signal
39 HSYNC_AP O 0/3.3 V DC (pulse) Image control signal
40 HSYNC_AN O 0/3.3 V DC (pulse) Image control signal
2-3-37
2LK/2LN/2LM/2LC
2-3-3 Power source PWB

30 ppm model/35 ppm model
1 4 3 18 1 1 6 16 1 1 4 1 6
YC3 YC14 1 8
YC12 YC11 YC13 YC7
1 3 YC9 YC10 YC8
1
YC1
2
TB3
TB1 TB2
YC4
1 4 1 3
1 6
YC5 YC6
Figure 2-3-3 Power source PWB silk-screen diagram (30 ppm model/35 ppm model)
2-3-38
2LK/2LN/2LM/2LC

TB 1 LIVE I 120 V AC AC power input
220-240 V AC
Connected to 2 NEUTRAL I 120 V AC AC power input
AC inlet and 220-240 V AC
main power
3 DH_LIVE I 120 V AC AC power input
switch
220-240 V AC
YC1 1 MSW_OUT O 120 V AC AC power output to MSW
220-240 V AC
Connected to 2 MSW_IN I 120 V AC AC power output from MSW
main power 220-240 V AC
switch
YC3 1 IH_NEUTRAL O 120 V AC AC power output to IHPWB

220-240 V AC
fuser IH PWB
3 IH_LIVE O 120 V AC AC power output to IHPWB
220-240 V AC
YC5 1 DH_LIVE O 120 V AC AC power output to CH
220-240 V AC
Connected to 2 DH_LIVE O 120 V AC AC power output to CH
cassette 220-240 V AC
heater
3 NC - - Not used
4 NC - - Not used
5 DH_NEUTRAL O 120 V AC AC power output to CH
220-240 V AC
220-240 V AC
YC6 1 DH_LIVE O 120 V AC AC power output to PFCH
220-240 V AC
Connected to 2 DH_NEUTRAL O 120 V AC AC power output to PFCH
paper feeder 220-240 V AC
/large capac-
ity feeder
YC7 1 +24V1 O 24 V DC 24 V DC power to LSURPWB
Connected to 2 +24V1 O 24 V DC 24 V DC power to LSURPWB
LSU relay
3 GND - - Ground
PWB
4 GND - - Ground
2-3-39
2LK/2LN/2LM/2LC

motor con-
3 GND - - Ground
trol PWB
4 +24V1 O 24 V DC 24 V DC power to MCPWB
YC9 1 +24V1 O 24 V DC 24 V DC power to FPWB1
Connected to 2 +24V1 O 24 V DC 24 V DC power to FPWB1
feed PWB 1
3 +24V1 O 24 V DC 24 V DC power to FPWB1
4 +12V O 12 V DC 12 V DC power to FPWB1
5 GND - - Ground
6 GND - - Ground
7 GND - - Ground
8 GND - - Ground
YC10 1 +24V1 O 24 V DC 24 V DC power to paper feeder/large
capacity feeder
Connected to 2 +24V1 O 24 V DC 24 V DC power to paper feeder/large
paper feeder/ capacity feeder
large capac- 3 +24V1 O 24 V DC 24 V DC power to 1000-sheet/4000-
ity feeder,
sheet finisher
1000-sheet/
4000-sheet 4 +24V1 O 24 V DC 12 V DC power to 1000-sheet/4000-
finisher and sheet finisher
ISC PWB 5 +24V1 O 24 V DC 24 V DC power to ISCPWB
6 +24V1 O 24 V DC 12 V DC power to ISCPWB
7 +24V1 - - Not used
9 GND - - Ground
10 GND - - Ground
11 GND - - Ground
12 GND - - Ground
13 GND - - Ground
14 GND - - Ground
15 GND - - Ground
16 GND - - Ground
2-3-40
2LK/2LN/2LM/2LC

YC13 1 +24V1 O 24 V DC 24 V DC power to HVPWB1
Connected to 2 +24V1 O 24 V DC 24 V DC power to HVPWB1
high voltage
3 +24V1 O 24 V DC 24 V DC power to HVPWB1
PWB 1
4 PGND - - Ground
5 PGND - - Ground
6 PGND - - Ground
YC14 1 POWER_OFF I 0/3.3 V DC Sleep mode signal: On/Off
Connected to 2 DRUM_HEAT_RE I 0/3.3 V DC FH: On/Off
feed PWB 1 M
3 GND - - Ground
4 FSR_RELAY_RE I 0/3.3 V DC Power relay signal: On/Off
M
1 +12V1 O 12 V DC 12 V DC power to MPWB
5 GND - - Ground
6 GND - - Ground
7 GND - - Ground
8 GND - - Ground
2-3-41
2LK/2LN/2LM/2LC
1 4 3 18 1 1 6 16 1 1 4 1 6
YC3 YC17 1 8
YC15 YC14 YC16 YC10
1 3 YC12 YC13 YC11
1 2
TB4
YC2
TB3
1 2
YC1
TB5
TB1 TB2
1 4
YC5
1 4
YC18
YC7
1 4 1 3
1 3
1 6
YC4
YC8 YC9
Figure 2-3-4 Power source PWB silk-screen diagram (45 ppm model/55 ppm model)
2-3-42
2LK/2LN/2LM/2LC

TB 1 LIVE I 120 V AC AC power input
220-240 V AC
Connected to 2 NEUTRAL I 120 V AC AC power input
AC inlet and 220-240 V AC
main power
3 LIVE - - Not used
switch
4 NEUTRAL - - Not used
5 DH_LIVE I 120 V AC AC power input
220-240 V AC
YC1 1 MSW_OUT O 120 V AC AC power output to MSW
220-240 V AC
Connected to 2 MSW_IN I 120 V AC AC power output from MSW
main power 220-240 V AC
switch
YC3 1 IH_NEUTRAL O 120 V AC AC power output to IHPWB

220-240 V AC
fuser IH PWB
3 IH_LIVE O 120 V AC AC power output to IHPWB
220-240 V AC
YC8 1 DH_LIVE O 120 V AC AC power output to CH
220-240 V AC
Connected to 2 DH_LIVE O 120 V AC AC power output to CH
cassette 220-240 V AC
heater
3 NC - - Not used
4 NC - - Not used
220-240 V AC
220-240 V AC
YC9 1 DH_LIVE O 120 V AC AC power output to PFCH
220-240 V AC
Connected to 2 DH_NEUTRAL O 120 V AC AC power output to PFCH
paper feeder/ 220-240 V AC
large capac-
ity feeder
YC10 1 +24V1 O 24 V DC 24 V DC power to LSURPWB
Connected to 2 +24V1 O 24 V DC 24 V DC power to LSURPWB
LSU relay
3 GND - - Ground
PWB
4 GND - - Ground
2-3-43
2LK/2LN/2LM/2LC

motor con-
3 GND - - Ground
trol PWB
feed PWB 1
5 GND - - Ground
6 GND - - Ground
7 GND - - Ground
8 GND - - Ground
YC13 1 +24V1 O 24 V DC 24 V DC power to paper feeder/large
capacity feeder
Connected to 2 +24V1 O 24 V DC 24 V DC power to paper feeder/large
paper feeder/ capacity feeder
large capac- 3 +24V1 O 24 V DC 24 V DC power to 1000-sheet/4000-
ity feeder,
sheet finisher
1000-sheet/
4000-sheet 4 +24V1 O 24 V DC 12 V DC power to 1000-sheet/4000-
finisher and sheet finisher
ISC PWB 5 +24V1 O 24 V DC 24 V DC power to ISCPWB
6 +24V1 O 24 V DC 12 V DC power to ISCPWB
9 GND - - Ground
10 GND - - Ground
11 GND - - Ground
12 GND - - Ground
13 GND - - Ground
14 GND - - Ground
15 GND - - Ground
16 GND - - Ground
2-3-44
2LK/2LN/2LM/2LC

YC14 1 +12V1 O 12 V DC 12 V DC power to MPWB
Connected to 2 +12V1 O 12 V DC 12 V DC power to MPWB
main PWB
5 GND - - Ground
6 GND - - Ground
7 GND - - Ground
8 GND - - Ground
Connected to 2 +24V1 O 24 V DC 24 V DC power to HVPWB1
high voltage
3 +24V1 O 24 V DC 24 V DC power to HVPWB1
PWB 1
4 PGND - - Ground
5 PGND - - Ground
6 PGND - - Ground
YC17 1 POWER_OFF I 0/3.3 V DC Sleep mode signal: On/Off
Connected to 2 DRUM_HEAT_RE I 0/3.3 V DC FH: On/Off
feed PWB 1 M
3 GND - - Ground
2-3-45
2LK/2LN/2LM/2LC
2-3-4 ISC PWB
4 1
3 1
YC5
1
YC14
YC1
5
1
YC13
3
1
YC9
40
1
YC6
11
1
YC11
6
1
YC4
7
1
8
YC7
YC3
6
1
1
YC12
3
YC8
16
YC2
1 5
Figure 2-3-5 ISC PWB silk-screen diagram
2-3-46
2LK/2LN/2LM/2LC

YC3 1 SC_CLK I 0/3.3 V DC (pulse) Scanner clock signal
Connected to 2 SC_SO O 0/3.3 V DC (pulse) Serial communication data signal
main PWB
3 SC_SI I 0/3.3 V DC (pulse) Serial communication data signal
4 SC_BSY I 0/3.3 V DC Scanner busy signal
5 SC_HLDN I 0/3.3 V DC Scanner hold signal
6 SC_DIR I 0/3.3 V DC Scanner communication direction sig-
nal
7 SC_IRN I 0/3.3 V DC Scanner interrupt signal
8 GND(SPARE) - - Ground
Connected to 2 HTPDN O 0/3.3 V DC Control signal
main PWB
3 LOCKN O 0/3.3 V DC Lock signal
4 GND - - Ground
5 TX0N O 0/3.3 V DC (pulse) Transmission data signal
6 TX0P O 0/3.3 V DC (pulse) Transmission data signal
7 GND - - Ground
YC5 1 SMOT AP O 0/24 V DC (pulse) SM drive control signal
Connected to 2 SMOT BP O 0/24 V DC (pulse) SM drive control signal
scanner 3 SMOT AN O 0/24 V DC (pulse) SM drive control signal
motor
4 SMOT BN O 0/24 V DC (pulse) SM drive control signal
YC6 1 +5V O 5 V DC 5 V DC power to LEDPWB
Connected to 2 FAIL I 0/3.3 V DC Error signal
LED PWB
3 SDA I/O 0/3.3 V DC Data signal
4 SCL O 0/3.3 V DC (pulse) Clock signal
5 VSET O Analog Analog voltage
6 SGND - - Ground
7 PGND - - Ground
8 PWM O 0/3.3 V DC PWM signal
9 POW O 0/3.3 V DC LED driver: On/Off
10 +24V1 O 24 V DC 24 V DC power to LEDPWB
11 +24V1 O 24 V DC 24 V DC power to LEDPWB
YC7 1 +24V1 I 24 V DC 24 V DC power from PSPWB
power source
3 GND - - Ground
PWB
4 GND - - Ground
5 +24V2 I 24 V DC 24 V DC power from PSPWB
2-3-47
2LK/2LN/2LM/2LC

YC8 1 +3.3V O 3.3 V DC 3.3 V DC power to HPS
home posi-
3 HP_SW I 0/3.3 V DC HPS: On/Off
tion sensor
Connected to 2 CCDCLK1 O 0/3.3 V DC (pulse) Clock signal
CCD PWB
3 GND - - Ground
4 CCDCLK2 O 0/3.3 V DC (pulse) Clock signal
5 GND - - Ground
6 CP O 0/3.3 V DC Clamp signal
7 GND - - Ground
8 RS O 0/3.3 V DC Reset signal
9 VSG O 0/3.3 V DC Control signal
10 TG O 0/3.3 V DC Control signal
11 SH O 0/3.3 V DC Shift gate signal
12 AFE_SI I 0/3.3 V DC (pulse) Serial communication data signal
13 AFE_EN O 0/3.3 V DC (pulse) Enable signal
14 AFE_SO O 0/3.3 V DC (pulse) Serial communication data signal
15 AFECLK O 0/3.3 V DC (pulse) Clock signal
16 GND - - Ground
17 DIS_CIS_1P I 0/3.3 V DC (pulse) Image data signal
18 DIS_CIS_1N I 0/3.3 V DC (pulse) Image data signal
19 GND - - Ground
22 GND - - Ground
25 GND - - Ground
28 GND - - Ground
31 GND - - Ground
32 DIS_CISCKP O 0/3.3 V DC (pulse) Clock signal
33 DIS_CISCKN O 0/3.3 V DC (pulse) Clock signal
2-3-48
2LK/2LN/2LM/2LC

Connected to 35 CCDSEL O 0/3.3 V DC Select signal
CCD PWB
36 GND - - Ground
37 AFE_MCLK O 0/3.3 V DC (pulse) Clock signal
38 GND(AFE_SHD) - - Ground
39 CLPIN O 0/3.3 V DC Clamp signal
40 GND(AFE_SHP) - - Ground
YC11 1 +5.1V O 5 V DC 5 V DC power to CCDPWB
CCD PWB
3 +10V O DC10V 10 V DC power to CCDPWB
4 GND - - Ground
5 +3.3V O 3.3 V DC 3.3 V DC power to CCDPWB
6 GND - - Ground
YC12 1 GND(SPARE) - - Ground
Connected to 2 DP_TMG I 0/3.3 V DC DPTS: On/Off
DP main
3 DP_RDY I 0/3.3 V DC ready signal
PWB
4 DP_SEL O 0/3.3 V DC Select signal
5 DP_CLK O 0/3.3 V DC (pulse) Clock signal
6 DP_SO O 0/3.3 V DC (pulse) Serial communication data signal
7 DP_SI I 0/3.3 V DC (pulse) Serial communication data signal
8 DP_OPEN I 0/3.3 V DC DPOCSW: On/Off
9 Reserve - - Not used
10 GND - - Ground
11 GND - - Ground
12 GND - - Ground
13 Reserve - - Not used
14 24V2 O 24 V DC 24 V DC power to DPMPWB
Connected to 2 ORG_SW I 0/3.3 V DC OSS: On/Off
original size
3 +5.1V O 5 V DC 5 V DC power to OSS
sensor
2-3-49
2LK/2LN/2LM/2LC

YC14 1 +3.3V O 3.3 V DC 3.3 V DC power to ODSW
original
3 CO_SW I 0/3.3 V DC ODSW: On/Off
detection
switch
2-3-50
2LK/2LN/2LM/2LC
2-3-5 Operation PWB 1
1 6
12 1
5 1
1
YC3 15 YC15 40 YC4 1
12
YC2
YC1
YC10
12
YC9
1
1
4
1
YC8
YC6
1
20
1
YC11
5
9
2
YC12
1
YC13
YC14
4
YC5
1
1
4
1
SW1
Figure 2-3-6 Operation PWB 1 silk-screen diagram
2-3-51
2LK/2LN/2LM/2LC

YC1 1 +5V I 5 V DC 5 V DC power from MPWB
Connected to 2 +5V I 5 V DC 5 V DC power from MPWB
main PWB
3 +5V I 5 V DC 5 V DC power from MPWB
4 GND - - Ground
5 GND - - Ground
YC2 1 VBUS I 5 V DC 5 V DC power input
Connected to 2 DN I/O - USB data signal
main PWB
3 DP I/O - USB data signal
4 ID - - Not used
5 GND - - Ground
Connected to 2 SECOND_TRAY_ - - Not used
main PWB SW
3 BEEP_POWERO I 0/3.3 V DC Sleep return signal
N
4 ENERGY_SAVE I 0/3.3 V DC Energy save signal
5 SUPND_POWER I 3.3 V DC 3.3 V DC power from MPWB
6 LED_MEMORY_N I 0/3.3 V DC Memory LED control signal
7 LED_ATTENTION I 0/3.3 V DC Attention LED control signal
_N
8 LED_PROCESSI I 0/3.3 V DC Processing LED control signal
NG_N
9 SHUT_DOWN I 0/3.3 V DC 24 V down signal
10 LIGHTOFF_POW I 0/3.3 V DC Sleep return signal
ERON
11 AUDIO I Analog Audio output signal
12 PANEL RESET I 0/3.3 V DC Reset signal
13 INT_POWERKEY O 0/3.3 V DC Power key: On/Off
_N
14 PANEL_STATUS O 0/3.3 V DC Operation panel status signal
15 SGND - - Ground
2-3-52
2LK/2LN/2LM/2LC

LCD
3 CK O 0/3.3 V DC (pulse) LCD clock signal
4 SGND - - Ground
5 SGND - - Ground
6 SC O 0/3.3 V DC LCD Control signal
7 R0(LSB) O 0/3.3 V DC LCD Control signal
8 R1 O 0/3.3 V DC LCD Control signal
10 SGND - - Ground
13 R5(MSB) O 0/3.3 V DC LCD Control signal
14 SGND - - Ground
15 G0(LSB) O 0/3.3 V DC LCD Control signal
16 G1 O 0/3.3 V DC LCD Control signal
18 SGND - - Ground
21 G5(MSB) O 0/3.3 V DC LCD Control signal
22 SGND - - Ground
23 B0(LSB) O 0/3.3 V DC LCD Control signal
24 B1 O 0/3.3 V DC LCD Control signal
26 SGND - - Ground
29 B5(MSB) O 0/3.3 V DC LCD Control signal
30 SGND - - Ground
31 H_SYNC O 0/3.3 V DC (pulse) LCD horizontal synchronization signal
32 SGND - - Ground
33 V_SYNC O 0/3.3 V DC (pulse) LCD vertical synchronization signal
34 SGND - - Ground
35 ENB O 0/3.3 V DC LCD enable signal
36 CM O 0/3.3 V DC LCD mode switch signal
2-3-53
2LK/2LN/2LM/2LC

YC4 37 3.3V O 3.3 V DC 3.3 V DC power to LCD
Connected to 38 3.3V O 3.3 V DC 3.3 V DC power to LCD
LCD
39 3.3V O 3.3 V DC 3.3 V DC power to LCD
40 3.3V O 3.3 V DC 3.3 V DC power to LCD
YC5 1 BOT Y- I Analog Touch panel Y- position signal
Connected to 2 LEFT X+ I Analog Touch panel X+ position signal
touch panel
3 TOP Y+ I Analog Touch panel Y+ position signal
4 RIGHT X- I Analog Touch panel X- position signal
YC6 1 KEY4 I 0/3.3 V DC (pulse) Operation panel key scan return sig-
nal 4
Connected to 2 SCAN2 O 0/3.3 V DC (pulse) Scan signal 2
operation 3 INT_POWERKEY I 0/3.3 V DC Power key: On/Off
PWB 2 _N
4 SCAN1 O 0/3.3 V DC (pulse) Scan signal 1
5 LED1 O 0/3.3 V DC (pulse) Operation panel LED display drive
signal 1
6 SUPND_POWER O 3.3 V DC 3.3 V DC power to OPWB2
7 KEY3 I 0/3.3 V DC (pulse) Operation panel key scan return sig-
nal 3
nal 2
nal 1
signal 0
nal 0
15 GND - - Ground
16 GND - - Ground
17 GND - - Ground
18 GND - - Ground
19 GND - - Ground
20 GND - - Ground
2-3-54
2LK/2LN/2LM/2LC

YC7 1 SCAN4 O 0/3.3 V DC (pulse) Scan signal 4
Connected to 2 KEY5 I 0/3.3 V DC (pulse) Operation panel key scan return sig-
operation nal 5
PWB 2 3 KEY6 I 0/3.3 V DC (pulse) Operation panel key scan return sig-
nal 6
nal 7
signal 2
signal 3
signal 4
12 GND - - Ground
YC8 1 PROCESSING_L O 0/3.3 V DC Processing LED control signal
ED
Connected to 2 MEMORY LED O 0/3.3 V DC Memory LED control signal
operation 3 ATTENTION_LED O 0/3.3 V DC Attention LED control signal
PWB 3
4 GND - - Ground
YC11 1 VO2 O Analog Speaker sound signal (+)
Connected to 2 VO1 O Analog Speaker sound signal (-)
speaker
YC14 1 LED_A O 0/3.3 V DC LED control signal
LCD
3 LED_C I 0/3.3 V DC LED control signal
4 NC - - Not used
2-3-55
2LK/2LN/2LM/2LC
Figure 2-3-7 Front PWB silk-screen diagram

20
21
1 YC4 9 1 YC5 20
40 1
YC6
1 10
YC16 1 9
2-3-56
1 20 50 1
YC1 YC2 YC3 YC17
1 8 YC19 1 YC8 10
YC18
YC14 YC13 YC12 YC11 YC9
40
1
1 10 1 10 1 10 1 10 1 3
YC10 1 YC7 11
YC15 1 10
1 11
1 11
2-3-6 Front PWB
2LK/2LN/2LM/2LC

YC1 1 +3.3V1 I 3.3 V DC 3.3 V DC power from EPWB
Connected to 2 +3.3V2 I 3.3 V DC 3.3 V DC power from EPWB
engine PWB
3 +5V I 5 V DC 5 V DC power from EPWB
6 GND - - Ground
7 GND - - Ground
8 GND - - Ground
9 GND - - Ground
10 GND - - Ground
Connected to 2 DRM_INDEX_Bk O 0/3.3 V DC DRM-K control signal
engine PWB
3 ERS_Bk_REM I 0/24 V DC CL-K: On/Off
4 TPD_ Bk_1 O Analog DEVPWB-K detection signal
5 DLP_VCONT_Bk I 0/3.3 V DC DEVPWB-K control signal
_1
6 TPD_TEMP_Bk O Analog Developer thermistor K detection sig-
nal
7 GND - - Ground
8 DRM_INDEX_M O 0/3.3 V DC DRM-M control signal
9 ERS_ M_REM I 0/24 V DC CL-M: On/Off
10 TPD_M_1 O Analog DEVPWB-M detection signal
11 DLP_VCONT_M_ I 0/3.3 V DC DEVPWB-M control signal
1
12 TPD_TEMP_M O Analog Developer thermistor M detection sig-
nal
13 GND - - Ground
14 DRM_INDEX_C O 0/3.3 V DC DRM-C control signal
15 ERS_C_REM I 0/24 V DC CL-C: On/Off
16 TPD_C_1 O Analog DEVPWB-C detection signal
17 DLP_VCONT_C_ I 0/3.3 V DC DEVPWB-C control signal
1
18 TPD_TEMP_C O Analog Developer thermistor C detection sig-
nal
19 GND - - Ground
20 TN_CLK I 0/3.3 V DC (pulse) Clock signal
21 GND - - Ground
22 EEP_SCL1 I 0/3.3 V DC (pulse) EEPROM clock signal
2-3-57
2LK/2LN/2LM/2LC

Connected to 24 EEP_SDA1 I/O 0/3.3 V DC (pulse) EEPROM data signal
engine PWB
25 GND - - Ground
26 TPD_Y_1 O Analog DEVPWB-Y detection signal
27 DLP_VCONT_Y_ I 0/3.3 V DC DEVPWB-Y control signal
1
28 TPD_TEMP_Y O Analog Developer thermistor Y detection sig-
nal
29 ERS_Y_REM I 0/24 V DC CL-Y: On/Off
30 DRM_INDEX_ Y O 0/3.3 V DC DRM-Y control signal
31 FRONT_OPEN O 0/3.3 V DC FRCSW: On/Off
32 GND - - Ground
33 I2C_SCL I 0/3.3 V DC (pulse) EEPROM clock signal
34 GND - - Ground
35 I2C_SDA I/O 0/3.3 V DC (pulse) EEPROM data signal
36 GND - - Ground
37 LSU_FAN_REM I 0/24 V DC LSUFM: On/Off
38 CLEAN_MOT_LO O 0/3.3 V DC WTM lock signal
CK
39 CLEAN_MOT_RE I 0/24 V DC WTM: On/Off
M
40 GND - - Ground
Connected to 2 WTNR_SET - - Not used
engine PWB
4 IH_CORE_SENS - - Not used
5 IH_CORE_MOT_ - - Not used
REM
6 IH_CORE_CLK - - Not used
7 WTNR_LED I 0/3.3 V DC (pulse) WTS1 LED emitter signal
8 IH_COIL_FAN_AL O 0/3.3 V DC CFM1 alarm signal
M
9 IH_COIL_FAN_H I 0/24 V DC CFM1: On/Off
10 IH_COIL_FAN_L I 0/24 V DC CFM1: On/Off
11 EXIT_FAN I 0/24 V DC EFFM: On/Off
12 CONTAIN_FAN - - Not used
13 JUNC_SOL_REM I 0/24 V DC FSSOL: On/Off (ACT)
14 JUNC_SOL_RET I 0/24 V DC FSSOL: On/Off (RET)
15 GND - - Ground
2-3-58
2LK/2LN/2LM/2LC

YC3 16 EXIT_PAPER_SE O 0/3.3 V DC EFS: On/Off
NS
Connected to 17 EXIT_FEED_SEN O 0/3.3 V DC SBS: On/Off
engine PWB S
18 SB_MOT_REM I 0/3.3 V DC EM: On/Off
19 SB_MOT_PH I 0/3.3 V DC EM control signal
20 SB_MOT_CLK I 0/3.3 V DC (pulse) EM clock signal
21 SB_MOT_PD I 0/3.3 V DC EM control signal
22 SB_MOT_DIR I 0/3.3 V DC EM drive switch signal
23 GND - - Ground
24 DLP_FAN_ Bk _H I 0/24 V DC DEVFM2: On/Off
25 DLP_FAN_ Bk _L I 0/24 V DC DEVFM2: On/Off
26 DLP_FAN_CLR_ I 0/24 V DC DEVFM1: On/Off
H
27 DLP_FAN_CLR_L I 0/24 V DC DEVFM1: On/Off
28 WTNR_FULL O Analog WTS2 detection signal
29 WTNR_NEAR O Analog WTS2 detection signal
30 WTNR_VCONT I 0/3.3 V DC WTS2 control signal
31 GND - - Ground
32 ROT_MOT_REM - - Not used
33 ROT_MOT_CLK - - Not used
34 ROT_MOT_PD - - Not used
35 ROT_MOT_DIR - - Not used
37 THOP_MOT_Bk_ - - Not used
REM
38 THOP_MOT_M_R - - Not used
EM
39 THOP_MOT_C_R - - Not used
EM
40 THOP_MOT_Y_R - - Not used
EM
41 GND - - Ground
42 ENCODE_ Bk - - Not used
43 ENCODE_M - - Not used
44 ENCODE_C - - Not used
45 ENCODE_Y - - Not used
46 THOP_ Bk - - Not used
47 THOP_M - - Not used
2-3-59
2LK/2LN/2LM/2LC

YC3 48 THOP_C - - Not used
Connected to 49 THOP_Y - - Not used
engine PWB
50 GND - - Ground
YC4 1 5V - - Not used
Connected to 2 LED1 - - Not used
coil fan motor
3 5V - - Not used
1 and eject
front fan 4 LED2 - - Not used
motor 5 IH_COIL_FAN_AL I 0/3.3 V DC CFM1 alarm signal
M
6 IH_COIL_FAN O 0/24 V DC CFM1: On/Off
7 24V O 24 V DC 24 V DC power to CFM1
8 24V O 24 V DC 24 V DC power to EFFM
9 EXIT FAN O 0/24 V DC EFFM: On/Off
YC5 1 ROT_CORE A - - Not used
Connected to 2 ROT_CORE B - - Not used
eject unit
3 ROT_CORE A/ - - Not used
4 ROT_CORE B/ - - Not used
5 GND - - Not used
7 5V - - Not used
8 SB_CORE B/ O 0/24 V DC (pulse) EM drive control signal
9 SB_CORE A/ O 0/24 V DC (pulse) EM drive control signal
10 SB_CORE B O 0/24 V DC (pulse) EM drive control signal
11 SB_CORE A O 0/24 V DC (pulse) EM drive control signal
12 GND - - Ground
13 EXIT_FEED_SEN I 0/3.3 V DC SBS: On/Off
S
14 5V O 5 V DC 5 V DC power to SBS
15 GND - - Ground
16 EXIT_PAPER_SE I 0/3.3 V DC EFS: On/Off
NS
17 5V O 5 V DC 5 V DC power to EFS
18 +24V1 O 24 V DC 24 V DC power to FSSOL
19 JUNC_SOL_KYU O 0/24 V DC FSSOL: On/Off (ACT)
20 JUNC_SOL_FUK O 0/24 V DC FSSOL: On/Off (RET)
2-3-60
2LK/2LN/2LM/2LC

YC6 1 24V O 24 V DC 24 V DC power to DEVFM2
Connected to 2 DLP_FAN_Bk O 0/24 V DC DEVFM2: On/Off
developer
3 24V O 24 V DC 24 V DC power to DEVFM1
fan motor 1/2
4 DLP_FAN_M O 0/24 V DC DEVFM1: On/Off
YC7 1 3.3V2 O 3.3 V DC 3.3 V DC power to DRPWB-K
Connected to 2 EEP_SCL1 O 0/3.3 V DC (pulse) EEPROM clock signal
drum unit K
4 GND - - Ground
5 DRM_ADR0_Bk - - Not used
6 DRM_ADR1_Bk - - Not used
7 24V O 24 V DC 24 V DC power to CL-K
8 ERS_Bk_REM O 0/24 V DC CL-K: On/Off
YC8 1 5V O 5 V DC 5 V DC power to WTS1
Connected to 2 WTNR_FULL I Analog WTS1 detection signal
waste toner
3 WTNR_LED O 0/3.3 V DC (pulse) WTS1 LED emitter signal
sensor 1/2
4 5V_LED O 5 V DC 5 V DC power to WTS1
5 GND - - Ground
6 WTNR_SET I Analog WTS2 detection signal
7 5V O 5 V DC 5 V DC power to WTS2
8 WTNR_NEAR - - Not used
9 WTNR_LED - - Not used
10 5V_LED - - Not used
YC9 1 TPD_TEMP_BK I Analog Developer thermistor K detection sig-
nal
Connected to 2 DLP_VCONT_BK O 0/3.3 V DC DEVPWB-K control signal
developer _1
unit K
3 TPD_BK_1 I Analog DEVPWB-K detection signal
4 TN_CLK_BK O 0/3.3 V DC (pulse) Clock signal
5 GND - - Ground
6 DLP_ADR1_BK - - Not used
7 DLP_ADR0_BK - - Not used
10 3.3V2 O 3.3 V DC 3.3 V DC power to DEVPWB-K
11 3V O 3.3 V DC 3.3 V DC power to VM-K
12 VIB_MOT O 0/24 V DC VM-K: On/Off
2-3-61
2LK/2LN/2LM/2LC

YC10 1 3.3V2 O 3.3 V DC 3.3 V DC power to DRPWB-M
drum unit M
4 GND - - Ground
5 DRM_ADR0_M - - Not used
6 DRM_ADR1_M - - Not used
7 24V O 24 V DC 24 V DC power to CL-M
8 ERS_M_REM O 0/24 V DC CL-M: On/Off
YC11 1 TPD_TEMP_M I Analog Developer thermistor M detection sig-
nal
Connected to 2 DLP_VCONT_M_ O 0/3.3 V DC DEVPWB-M control signal
developer 1
unit M
3 TPD_M_1 I Analog DEVPWB-M detection signal
4 TN_CLK_M O 0/3.3 V DC (pulse) Clock signal
5 GND - - Ground
6 DLP_ADR1_M - - Not used
7 DLP_ADR0_M - - Not used
10 3.3V2 O 3.3 V DC 3.3 V DC power to DEVPWB-M
11 3V O 3.3 V DC 3.3 V DC power to VM-M
12 VIB_MOT O 0/24 V DC VM-M: On/Off
YC12 1 3.3V2 O 3.3 V DC 3.3 V DC power to DRPWB-C
drum unit C
4 GND - - Ground
5 DRM_ADR0_C - - Not used
6 DRM_ADR1_C - - Not used
7 24V O 24 V DC 24 V DC power to CL-C
8 ERS_C_REM O 0/24 V DC CL-C: On/Off
2-3-62
2LK/2LN/2LM/2LC

YC13 1 TPD_TEMP_C I Analog Developer thermistor C detection sig-
nal
Connected to 2 DLP_VCONT_C_ O 0/3.3 V DC DEVPWB-C control signal
developer 1
unit C
3 TPD_C_1 I Analog DEVPWB-C detection signal
4 TN_CLK_C O 0/3.3 V DC (pulse) Clock signal
5 GND - - Ground
6 DLP_ADR1_C - - Not used
7 DLP_ADR0_C - - Not used
10 3.3V2 O 3.3 V DC 3.3 V DC power to DEVPWB-C
11 3V O 3.3 V DC 3.3 V DC power to VM-C
12 VIB_MOT O 0/24 V DC VM-C: On/Off
YC14 1 3.3V2 O 3.3 V DC 3.3 V DC power to DRPWB-Y
drum unit Y
4 GND - - Ground
5 DRM_ADR0_ Y - - Not used
6 DRM _ADR1_ Y - - Not used
7 24V O 24 V DC 24 V DC power to CL-Y
8 ERS_ Y _REM O 0/24 V DC CL-Y: On/Off
YC15 1 TPD_TEMP_Y I Analog Developer thermistor Y detection sig-
nal
Connected to 2 DLP_VCONT_Y_ O 0/3.3 V DC DEVPWB-Y control signal
developer 1
unit Y
3 TPD_Y_1 I Analog DEVPWB-Y detection signal
4 TN_CLK_Y O 0/3.3 V DC (pulse) Clock signal
5 GND - - Ground
6 DLP_ADR1_Y - - Not used
7 DLP_ADR0_Y - - Not used
10 3.3V2 O 3.3 V DC 3.3 V DC power to DEVPWB-Y
11 3V O 3.3 V DC 3.3 V DC power to VM-Y
12 VIB_MOT O 0/24 V DC VM-Y: On/Off
2-3-63
2LK/2LN/2LM/2LC

YC16 1 3.3V1 O 3.3 V DC 3.3 V DC power to OTEM1
Connected to 2 I2C_SDA I 0/3.3 V DC (pulse) EEPROM data signal
outer temper-
3 GND - - Ground
ature sensor
1, front cover 4 I2C_SCL O 0/3.3 V DC (pulse) EEPROM clock signal
switch, LSU 5 FRONT_OPEN O 0/3.3 V DC FRCSW: On/Off
fan motor
6 GND - - Ground
and waste
toner motor 7 24V O 24 V DC 24 V DC power to LSUFM
8 LSU_FAN_OUT O DC0V/243V LSUFM: On/Off
9 CL_MOT O DC0V/243V WTM: On/Off
10 24V O 24 V DC 24 V DC power to WTM
11 GND - - Ground
YC19 1 3.3V1 O 3.3 V DC 3.3 V DC power to OTEM2
Connected to 2 I2C_SDA I 0/3.3 V DC (pulse) EEPROM data signal
outer temper-
3 GND - - Ground
ature sensor
2 4 I2C_SCL O 0/3.3 V DC (pulse) EEPROM clock signal
2-3-64
2LK/2LN/2LM/2LC
2-3-7 Feed PWB 1
YC20
2
11 1
YC19
8 YC3 1
64
1
7
YC18
1 YC27 9 4 YC26 1
YC4
1
20
1
YC17
50
YC4
1
18
1
YC14
2
15
YC16
YC10
1
12 1
1
1
YC23
6
YC4
YC12
YC13
YC22 YC25
1
2 1
YC9 4 1
8
10
8 1 7 YC8 1
3 1
YC11 YC5
YC15
3 1 3 1
Figure 2-3-8 Feed PWB 1 silk-screen diagram
2-3-65
2LK/2LN/2LM/2LC

Connected to 2 REG_F_LED I Analog IDS1 control signal
engine PWB
3 REG_SENS_F_P O Analog IDS1 detection signal
4 REG_SENS_F_S O Analog IDS1 detection signal
5 GND - - Ground
6 REG_R_LED I Analog IDS2 control signal
7 REG_SENS_RP( O Analog IDS2 detection signal
BK)
8 REG_SENS_RS( O Analog IDS2 detection signal
BK)
9 CLN_SOL_REM I 0/24 V DC CLSOL: On/Off (ACT)
10 CLN_SOL_RET I 0/24 V DC CLSOL: On/Off (RET)
11 GND - - Ground
13 DU_SENS O 0/3.3 V DC DUS2: On/Off
14 PRESS_RLS_SE O 0/3.3 V DC TRRS: On/Off
NS
15 PRESS_MOT_RE I 0/24 V DC TRRM: On/Off
M2
16 PRESS_MOT_RE I 0/24 V DC TRRM: On/Off
M1
18 DU_OPEN O 0/3.3 V DC DUCSW: On/Off
19 GND - - Ground
20 DU2_REM(CL_L I 0/3.3 V DC DUM2/DUCL2: On/Off
OW)
21 DU2_CLK I 0/3.3 V DC (pulse) DUM2 clock signal
22 DU2_PD I 0/3.3 V DC DUM2 control signal
24 TC_TONER_VCO - - Not used
NT
L
27 TC_MOT_LOCK - - Not used
28 GND - - Ground
29 MPF_LIFT1 I 0/24 V DC MPLM: On/Off
30 MPF_LIF2 I 0/24 V DC MPLM: On/Off
31 MPF_CL I 0/24 V DC MPPFCL: On/Off
2-3-66
2LK/2LN/2LM/2LC

YC1 32 MPF_JAM O 0/3.3 V DC MPFS: On/Off
Connected to 33 MPF_LIFT_DOW O 0/3.3 V DC MPLS2: On/Off
engine PWB N
34 MPF_LIFT_UP O 0/3.3 V DC MPLS1: On/Off
35 MPF_PPR_SET O 0/3.3 V DC MPPS: On/Off
36 GND - - Ground
37 MPF_LNG O 0/3.3 V DC MPPLSW: On/Off
38 MPF_WID3 O 0/3.3 V DC MPPWSW: On/Off
41 MPF_TABLE O 0/3.3 V DC MPTSW: On/Off
42 GND - - Ground
43 FSR_MOT_BRK I 0/3.3 V DC FUM break signal
44 FSR_MOT_DIR I 0/3.3 V DC FUM drive switch signal
45 FSR_MOT_RDY O 0/3.3 V DC FUM ready signal
46 FSR_MOT_CLK I 0/3.3 V DC (pulse) FUM clock signal
47 FSR_MOT_REM I 0/3.3 V DC FUM: On/Off
48 FSR_CL_REM - - Not used
49 GND - - Ground
50 EXIT_REAR_FAN I 0/24 V DC ERFM: On/Off
_H
51 EXIT_REAR_FAN I 0/24 V DC ERFM: On/Off
_L
53 FSR_RELAY I 0/3.3 V DC Fuser relay signal
55 SUB_HEAT_REM - - Not used
56 MAIN_HEAT_RE - - Not used
M
57 GND - - Ground
58 JOB_SOL_REM I 0/24 V DC JFSSOL: On/Off
59 JOB_OPEN_SEN O 0/3.3 V DC JOCS: On/Off
S
60 JOB_MOT_DIR I 0/3.3 V DC JEM drive switch signal
61 JOB_MOT_CLK I 0/3.3 V DC (pulse) JEM clock signal
62 JOB_MOT_REM I 0/3.3 V DC JEM: On/Off
63 JOB_SET O 0/3.3 V DC Job separator set signal
64 GND - - Ground
2-3-67
2LK/2LN/2LM/2LC

Connected to 2 IH_PWB_FAN(U) - - Not used
engine PWB _ALM
3 DRM_HEAT_REM - - Not used
4 POWER_OFF I 0/3.3 V DC Power off signal
5 IH_PWB_FAN_AL O 0/3.3 V DC IHFM alarm signal
M
6 IH_PWB_FAN_H I 0/24 V DC IHFM: On/Off
7 IH_PWB_FAN_L - - Not used
8 GND - - Ground
9 REG_MOT_REM( I 0/3.3 V DC RM/RCL: On/Off
CL)
10 REG_MOT_CLK I 0/3.3 V DC (pulse) RM clock signal
11 REG_MOT_PD I 0/3.3 V DC RM control signal
12 GND - - Ground
DIR
RDY
CLK
REM
17 GND - - Ground
DIR
RDY
20 DRM_MOT_BK_C - - Not used
LR_CLK
REM
22 GND - - Ground
23 DLP_MOT_BK_DI - - Not used
R
DY
25 DLP_MOT_BK_C - - Not used
LK
EM
2-3-68
2LK/2LN/2LM/2LC

Connected to 28 DRM_MOT_BK_B - - Not used
engine PWB RK
29 DRM_MOT_BK_D - - Not used
IR
DY
EM
32 GND - - Ground
33 TRANS_MOT_BR I 0/3.3 V DC TRCM break signal
K
34 TRANS_MOT_DI I 0/3.3 V DC TRCM drive switch signal
R
35 TRANS_MOT_RD O 0/3.3 V DC TRCM ready signal
Y
36 TRANS_MOT_CL I 0/3.3 V DC (pulse) TRCM clock signal
K
37 TRANS_MOT_RE I 0/3.3 V DC TRCM: On/Off
M
38 GND - - Ground
39 TCON_SET - - Not used
40 DU_ENTER_SEN O 0/3.3 V DC DUS1: On/Off
S
41 EXIT_FAN I 0/24 V DC EFM: On/Off
42 GND - - Ground
43 DU1_MOT_REM( I 0/3.3 V DC DUM1/DUCL1: On/Off
CL_H)
44 DU1_MOT_CLK I 0/3.3 V DC (pulse) DUM1 clock signal
45 DU1_MOT_PD I 0/3.3 V DC DUM1 control signal
46 EDGE_FAN_H I 0/24 V DC FUFM: On/Off
47 GND - - Ground
48 LOOP_SENS O 0/3.3 V DC LPS: On/Off
49 M_TEMP - - Not used
50 GND - - Ground
2-3-69
2LK/2LN/2LM/2LC

YC3 1 +24V1 O 24 V DC 24 V DC power to EPWB
Connected to 2 +24V1 O 24 V DC 24 V DC power to EPWB
engine PWB 3 GND - - Ground
4 GND - - Ground
5 +12V O 12 V DC 12 V DC power to EPWB
6 GND - - Ground
7 +5V O 5 V DC 5 V DC power to EPWB
8 GND - - Ground
YC4 1 +24V1 I 24 V DC 24 V DC power from PSPWB
Connected to 2 +24V1 I 24 V DC 24 V DC power from PSPWB
power source
PWB
4 +12V I 12 V DC 12 V DC power from PSPWB
5 GND - - Ground
6 GND - - Ground
7 GND - - Ground
8 GND - - Ground
Connected to 2 DRM_HEAT_REM O 0/3.3 V DC FH: On/Off
power source
3 POWER_OFF O 0/3.3 V DC Sleep mode signal: On/Off
PWB
Connected to 2 M_TEMP - - Not used
ID sensor1/2 3 3.3V O 3.3 V DC 3.3 V DC power to IDS1
and cleaning
solenoid 4 REG_F_LED O Analog IDS1 control signal
5 GND - - Ground
6 REG_SENS_F_P I Analog IDS1 detection signal
7 REG_SENS_F_S I Analog IDS1 detection signal
8 3.3V O 3.3 V DC 3.3 V DC power to IDS2
9 REG_R_LED O Analog IDS2 control signal
10 GND - - Ground
11 REG_SENS_R_P I Analog IDS2 detection signal
12 REG_SENS_R_S I Analog IDS2 detection signal
13 24V O 24 V DC 24 V DC power to CLSOL
14 CLN_SOL_REM O 0/24 V DC CLSOL: On/Off (ACT)
15 CLN_SOL_RET O 0/24 V DC CLSOL: On/Off (RET)
2-3-70
2LK/2LN/2LM/2LC

YC11 1 +24V1 O 24 V DC 24 V DC power to IHFM
Connected to 2 IH_PWB_FAN O 0/24 V DC IHFM: On/Off
IH fan motor 3 IH_PWB_FAN_AL I 0/3.3 V DC IHFM alarm signal
M
feed PWB 2 3 +5V O 5 V DC 5 V DC power to FPWB2
4 GND - - Ground
5 GND - - Ground
6 GND - - Ground
YC13 1 TRANS_MOT_BR O 0/3.3 V DC TRM break signal
K
Connected to 2 TRANS_MOT_DI O 0/3.3 V DC TRM drive switch signal
transfer R
motor 3 TRANS_MOT_RD I 0/3.3 V DC TRM ready signal
Y
4 TRANS_MOT_CL O 0/3.3 V DC (pulse) TRM clock signal
K
5 TRANS_MOT_RE O 0/24 V DC TRM: On/Off
M
6 GND - - Ground
7 24V2 O 24 V DC 24 V DC power to TRM
8 GND - - Not used
9 24V2 - - Not used
10 TANK_SET - - Not used
YC14 1 REG_BK_LED - - Not used
Connected to 2 REG_BK_SENS1 - - Not used
relay PWB _P
3 REG_BK_SENS1 - - Not used
_S
5 DU_SENS I 0/3.3 V DC DUS2: On/Off
6 PRESS_RLS_SE I 0/3.3 V DC TRRS: On/Off
NS
7 5V O 5 V DC 5 V DC power to FPWB2
8 PRESS_RLSMOT O 0/24 V DC TRRM: On/Off
21
9 PRESS_RLSMOT O 0/24 V DC TRRM: On/Off
2
2-3-71
2LK/2LN/2LM/2LC

YC14 10 24V2 O 24 V DC 24 V DC power to FPWB2
Connected to 11 DU_FAN - - Not used
relay PWB
12 DU_CL_LOWER_ O 0/24 V DC DUCL2: On/Off
REM
13 DU_OPEN_SW I 0/3.3 V DC DUCSW: On/Off
14 DU2_B/ O 0/24 V DC (pulse) DUM2 drive control signal
15 DU2_A/ O 0/24 V DC (pulse) DUM2 drive control signal
16 DU2_B O 0/24 V DC (pulse) DUM2 drive control signal
17 DU2_A O 0/24 V DC (pulse) DUM2 drive control signal
18 5V_LED - - Not used
YC15 1 +24V1 O 24 V DC 24 V DC power to PCUSW
Connected to 2 N.C - - Not used
paper con-
3 +24V2 I 24 V DC 24 V DC power from PCUSW
veying unit
switch
high voltage
PWB 2
YC17 1 TC_TONER_LED - - Not used
Connected to 2 TC_TONER_FUL - - Not used
relay PWB L
3 TC_TONER_MOT - - Not used
_B
_A
5 MPF_LIFT_MOT_ O 0/24 V DC MPLM: On/Off
B
6 MPF_LIFT_MOT_ O 0/24 V DC MPLM: On/Off
A
7 24V2 O 24 V DC 24 V dc power to FPWB2
8 MPF_CL_REM O 0/24 V DC MPPFCL: On/Off
9 MPF_JAM_SENS I 0/3.3 V DC MPFS: On/Off
N_SENS
11 MPF_LIFT_UP_S I 0/3.3 V DC MPLS1: On/Off
ENS
13 LED_3.3V3 O 3.3 V DC 3.3 V DC power to FPWB2
14 MPF_LNG I 0/3.3 V DC MPPLSW: On/Off
2-3-72
2LK/2LN/2LM/2LC

YC17 15 MPF_WID3 I 0/3.3 V DC MPPWSW: On/Off
Connected to 16 MPF_WID2 I 0/3.3 V DC MPPWSW: On/Off
relay PWB
19 GND - - Ground
20 GND - - Ground
YC18 1 FSR_MOT_BRK O 0/3.3 V DC FUM break signal
Connected to 2 FSR_MOT_DIR O 0/3.3 V DC FUM drive switch signal
fuser motor 3 FSR_MOT_RDY I 0/3.3 V DC FUM ready signal
4 FSR_MOT_CLK O 0/3.3 V DC (pulse) FUM clock signal
5 FSR_MOT_REM O 0/24 V DC FUM: On/Off
6 GND - - Ground
7 24V2 O 24 V DC 24 V DC power to FUM
YC19 1 EXIT_REAR_FAN O 0/24 V DC ERFM: On/Off
Connected to 2 +24V1 O 24 V DC 24 V DC power to ERFM
eject rear fan
motor
YC20 1 JOB_SET I 0/3.3 V DC Job separator set signal
job separator 3 GND - - Ground
4 JOB_MOT_REM O 0/3.3 V DC JEM: On/Off
5 24V1 O 24 V DC 24 V DC power to JMPWB
6 JOB_MOT_CLK O 0/3.3 V DC (pulse) JEM clock signal
7 5V O 5 V DC 5 V DC power to JMPWB
8 JOB_MOT_DIR O 0/3.3 V DC JEM drive switch signal
9 JOB_OPEN_SEN I 0/3.3 V DC JOCS: On/Off
S
10 JOB_SOL_REM O 0/24 V DC JFSSOL: On/Off
11 NC - - Not used
2-3-73
2LK/2LN/2LM/2LC

YC23 1 DU_ENTER_SEN I 0/3.3 V DC DUS1: On/Off
S
Connected to 2 EXIT_FAN O 0/24 V DC EFM: On/Off
relay PWB 3 24V2 O 24 V DC 24 V DC power to FPWB2
4 DU_CL_UPPER_ O 0/24 V DC DUCL1: On/Off
REM
5 GND - - Ground
6 DU1_B/ O 0/24 V DC (pulse) DUM1 drive control signal
10 EDGE_FAN_REM O 0/24 V DC FUFM: On/Off
11 LOOP_SENS I 0/3.3 V DC LPS: On/Off
12 3.3V O 3.3 V DC 3.3 V DC power to FPWB2
YC25 1 REG_MOT_B/ O 0/24 V DC (pulse) RM drive control signal
Connected to 2 REG_MOT_A/ O 0/24 V DC (pulse) RM drive control signal
registration
3 REG_MOT_B O 0/24 V DC (pulse) RM drive control signal
motor
4 REG_MOT_A O 0/24 V DC (pulse) RM drive control signal
YC26 1 3.3V2 O 3.3 V DC 3.3 V DC power to EPWB
Connected to 2 3.3V3 O 3.3 V DC 3.3 V DC power to EPWB
4 GND - - Ground
YC27 1 MAIN_HEAT_RE - - Not used
M
Connected to 2 SUB_HEAT_REM - - Not used
fuser IH PWB 3 +24V2 - - Not used
5 GND - - Not used
6 GND - - Ground
7 FSR_RELAY O 0/3.3 V DC Fuser relay signal
8 +24V1 O 24 V DC 24 V DC power to IHPWB
2-3-74
2LK/2LN/2LM/2LC
2-3-8 Feed PWB 2
1 6
50 1
YC11
1
YC1
YC10
1 7
2
YC2
1
1
YC4
YC7
4
28
1
15
24
YC3
YC8
15
14
1
1
13
12
YC12
YC13
1
1
YC5
YC6
2
3
3
Figure 2-3-9 Feed PWB 2 silk-screen diagram
2-3-75
2LK/2LN/2LM/2LC

Connected to 2 FEED_MOT_REM I 0/3.3 V DC PFM: On/Off
engine PWB 3 FEED_MOT_CLK I 0/3.3 V DC (pulse) PFM clock signal
4 FEED_MOT_RDY O 0/3.3 V DC PFM ready signal
5 FEED_MOT_DIR I 0/3.3 V DC PFM drive switch signal
6 FEED_CL1_REM I 0/24 V DC PFCL1: On/Off
7 FEED_CL2_REM I 0/24 V DC PFCL2: On/Off
8 ASIST_CL2 I 0/24 V DC ASCL2: On/Off
9 LIFT_MOT2_REM I 0/24 V DC LM2: On/Off
10 GND - - Ground
11 LIFT_MOT1_REM I 0/24 V DC LM1: On/Off
1
12 CAS2_WID O 0/3.3 V DC PWSW2: On/Off
13 CAS2_LNG3 O 0/3.3 V DC PLSW2: On/Off
16 CAS1_WID O 0/3.3 V DC PWSW1: On/Off
20 GND - - Ground
21 CAS2_QUANT2 O 0/3.3 V DC PGS2(L): On/Off
22 CAS2_QUANT1 O 0/3.3 V DC PGS2(U): On/Off
23 CAS1_QUANT2 O 0/3.3 V DC PGS1(L): On/Off
24 CAS1_QUANT1 O 0/3.3 V DC PGS1(U): On/Off
25 LIFT_MOT1_LOC O 0/3.3 V DC LM1 lock signal
K
26 LIFT_MOT2_LOC O 0/3.3 V DC LM2 lock signal
K
27 CURRENT_SIG O 0/3.3 V DC Current signal
28 V-FEED_CL I 0/24 V DC PCCL: On/Off
29 COVER_OPEN O 0/3.3 V DC RLCSW: On/Off
30 FEED2_SENS O 0/3.3 V DC PFPCS1: On/Off
31 CAS1_P0 O 0/3.3 V DC FS1: On/Off
32 CAS1_LIFT_UP O 0/3.3 V DC LS1: On/Off
33 GND - - Ground
34 CAS1_EMPTY O 0/3.3 V DC PS1: On/Off
2-3-76
2LK/2LN/2LM/2LC

YC1 35 PICK_SOL1_RET I 0/24 V DC PUSOL1: On/Off (RET)
Connected to 36 PICK_SOL1_REM I 0/24 V DC PUSOL1: On/Off (ACT)
engine PWB
37 CAS2_P0 O 0/3.3 V DC FS2: On/Off
38 CAS2_LIFT_UP O 0/3.3 V DC LS2: On/Off
39 CAS2_EMPTY O 0/3.3 V DC PS2: On/Off
40 PICK_SOL2_RET I 0/24 V DC PUSOL2: On/Off (RET)
41 PICK_SOL2_REM I 0/24 V DC PUSOL2: On/Off (ACT)
42 GND - - Ground
43 REG_SENS O 0/3.3 V DC RS: On/Off
44 FEED1_SENS O 0/3.3 V DC PCS: On/Off
45 BEND_SENS O 0/3.3 V DC RDS: On/Off
46 MID_MOT_PH I 0/3.3 V DC MM control signal
47 MID_MOT_REM( I 0/3.3 V DC MM/MCL: On/Off
ROL_CL)
48 MID_MOT_CLK I 0/3.3 V DC (pulse) MM clock signal
49 MID_MOT_PD I 0/3.3 V DC MM control signal
50 ASIST_CL1 I 0/24 V DC ASCL1: On/Off
YC2 1 FEED_MOT_GAI - - Not used
N
Connected to 2 FEED_MOT_DIR O 0/3.3 V DC PFM drive switch signal
paper feed
3 FEED_MOT_RDY I 0/3.3 V DC PFM ready signal
motor
4 FEED_MOT_CLK O 0/3.3 V DC (pulse) PFM clock signal
5 FEED_MOT_REM O 0/3.3 V DC PFM: On/Off
6 GND - - Ground
7 24V2 O 24 V DC 24 V DC power to PFM
YC3 1 CAS1_LNG1 I 0/3.3 V DC PLSW1: On/Off
Connected to 2 CAS1_LNG2 I 0/3.3 V DC PLSW1: On/Off
paper length 3 GND - - Ground
switch 1/2,
paper width 4 CAS1_LNG3 I 0/3.3 V DC PLSW1: On/Off
switch 1/2, lift 5 CAS1_WID I 0/3.3 V DC PWSW1: On/Off
motor 1/2,
6 GND - - Ground
paper gauge
sensor 1(U)/ 7 CAS2_LNG1 I 0/3.3 V DC PLSW2: On/Off
(L) and paper 8 CAS2_LNG2 I 0/3.3 V DC PLSW2: On/Off
gauge sen-
9 GND - - Ground
sor 2(U)/(L)
12 GND - - Ground
2-3-77
2LK/2LN/2LM/2LC

YC3 13 LIFT_MOT1_RET O 0/24 V DC LM1: On/Off
Connected to 14 LIFT_MOT1_DR O 0/24 V DC LM1: On/Off
paper length
15 LIFT_MOT2_RET O 0/24 V DC LM2: On/Off
switch 1/2,
paper width 16 LIFT_MOT2_DR O 0/24 V DC LM2: On/Off
switch 1/2, lift 17 LED_5V O 5 V DC 5 V DC power to PGS1(U)
motor 1/2,
18 GND - - Ground
paper gauge
sensor 1(U)/ 19 CAS1_QUANT1 I 0/3.3 V DC PGS1(U): On/Off
(L) and paper 20 LED_5V O 5 V DC 5 V DC power to PGS1(L)
gauge sen-
sor 2(U)/(L) 21 GND - - Ground
23 LED_5V O 5 V DC 5 V DC power to PGS2(U)
24 GND - - Ground
25 CAS2_QUANT1 I 0/3.3 V DC PGS2(U): On/Off
26 LED_5V O 5 V DC 5 V DC power to PGS2(L)
27 GND - - Ground
YC4 1 FEED_CL1_REM O 0/24 V DC PFCL1: On/Off
Connected to 2 24V2 O 24 V DC PFCL124 V DC power to PFCL1
paper feed
clutch 1/2
4 24V2 O 24 V DC 24 V DC power to PFCL2
Connected to 2 24V2 O 24 V DC 24 V DC power to PCCL
paper con-
3 V-FEED_CL_REM O 0/24 V DC PCCL: On/Off
veying clutch
YC6 1 LED_5V O 5 V DC 5 V DC power to PCS
paper con- 3 FEED2_SENS I 0/3.3 V DC PCS: On/Off
veying sen-
sor and 4 COVER_OPEN I 0/3.3 V DC PCCSW: On/Off
paper con- 5 GND - - Ground
veying cover
switch
2-3-78
2LK/2LN/2LM/2LC

YC7 1 MID_B/ O 0/24 V DC (pulse) MM drive control signal
Connected to 2 MID_A/ O 0/24 V DC (pulse) MM drive control signal
middle motor,
3 MID_B O 0/24 V DC (pulse) MM drive control signal
regist deflec-
tion sensor, 4 MID_A O 0/24 V DC (pulse) MM drive control signal
middle sen- 5 BEND_SENS I 0/3.3 V DC RDS: On/Off
sor and reg-
6 GND - - Ground
istration
sensor 7 5V O 5 V DC 5 V DC power to RDS
8 GND - - Ground
9 FEED1_SENS I 0/3.3 V DC MS: On/Off
10 5V O 5 V DC 5 V DC power to MS
11 GND - - Ground
12 REG_SENS I 0/3.3 V DC RS: On/Off
13 5V O 5 V DC 5 V DC power to RS
14 MID_CL_REM O 0/24 V DC MCL: On/Off
15 24V2 O 24 V DC 24 V DC power to MCL
YC8 1 24V2 O 24 V DC 24 V DC power to PUSOL1
Connected to 2 PICK_SOL1_REM O 0/24 V DC PUSOL1: On/Off (ACT)
primary
paper feed
unit 4 LED_5V O 5 V DC 5 V DC power to PS1
5 GND - - Ground
6 CAS1_EMPTY_S I 0/3.3 V DC PS1: On/Off
ENS
7 LED_5V O 5 V DC 5 V DC power to LS1
8 GND - - Ground
9 CAS1_LIFT_UP_ I 0/3.3 V DC LS1: On/Off
SENS
10 5V O 5 V DC 5 V DC power to FS1
11 CAS1_P0_SENS I 0/3.3 V DC FS1: On/Off
12 GND - - Ground
13 24V2 O 24 V DC 24 V DC power to PUSOL2
16 LED_5V O 5 V DC 5 V DC power to PS2
17 GND - - Ground
18 CAS2_EMPTY_S I 0/3.3 V DC PS2: On/Off
ENS
19 LED_5V O 5 V DC 5 V DC power to LS2
2-3-79
2LK/2LN/2LM/2LC

Connected to 21 CAS2_LIFT_UP_ I 0/3.3 V DC LS2: On/Off
primary SENS
paper feed 22 5V O 5 V DC 5 V DC power to FS2
unit
23 CAS2_P0_SENS I 0/3.3 V DC FS2: On/Off
24 GND - - Ground
YC10 1 ASIST_CL1 O 0/24 V DC ASCL1: On/Off
Connected to 2 24V2 O 24 V DC 24 V DC power to ASCL1
assist clutch
1
feed PWB 1
3 GND - - Ground
YC12 1 ASIST_CL2 O 0/24 V DC ASCL2: On/Off
Connected to 2 24V2 O 24 V DC 24 V DC power to ASCL2
assist clutch
2
YC13 1 CURRENT_SIG I 0/3.3 V DC Current signal
current PWB 3 5V1 I 5 V DC 5 V DC power from CRPWB
2-3-80
2LK/2LN/2LM/2LC
2-3-9 Relay PWB
1 YC6 7
10 YC5 1
9
2
YC15
YC2
1
1
1
1
YC12
YC3
16
20
1
YC4
8
2
1
YC7
4
1
YC8
YC1
1 6
3
YC14
YC9
18
1
12
11
YC10
YC13
1
YC16
1
1 8
YC11
9 1
Figure 2-3-10 Relay PWB silk-screen diagram
2-3-81
2LK/2LN/2LM/2LC

YC1 1 5V_LED - - Not used
Connected to 2 DU2_A I 0/24 V DC (pulse) DUM2 drive control signal
feed PWB 1
3 DU2_B I 0/24 V DC (pulse) DUM2 drive control signal
4 DU2_A/ I 0/24 V DC (pulse) DUM2 drive control signal
5 DU2_B/ I 0/24 V DC (pulse) DUM2 drive control signal
6 DU_OPEN_SW O 0/3.3 V DC DUCSW: On/Off
7 DU_CL_LOWER_ I 0/24 V DC DUCL2: On/Off
REM
9 24V2 I 24 V DC 24 V DC power from FPWB1
10 PRESS_RLS_RE I 0/24 V DC TRRM: On/Off
M2
11 PRESS_RLS_RE I 0/24 V DC TRRM: On/Off
M1
12 5V I 5 V DC 5 V DC power from FPWB1
13 PRESS_RLS_SE O 0/3.3 V DC TRRS: On/Off
NS
14 DU_SENS O 0/3.3 V DC DUS2: On/Off
_S
_P
18 REG_BK_LED - - Not used
Connected to 2 MPF_LNG I 0/3.3 V DC MPPLSW: On/Off
MP tray unit 3 5V O 5 V DC 5 V DC power to MPPLSW
6 GND - - Ground
8 GND - - Ground
2-3-82
2LK/2LN/2LM/2LC

YC3 1 LED_3.3V3 O 3.3 V DC 3.3 V DC power to MPPLSW
MP tray unit
4 GND - - Ground
5 MPF_LIFT_UP_S I 0/3.3 V DC MPLS1: On/Off
ENS
6 5V O 5 V DC 5 V DC power to MPLS1
7 GND - - Ground
N_SENS
9 5V O 5 V DC 5 V DC power to MPLS1
10 GND - - Ground
11 MPF_JAM_SENS I 0/3.3 V DC MPFS: On/Off
12 5V O 5 V DC 5 V DC power to MPFS
13 MPF_CL_REM O 0/24 V DC MPPFCL: On/Off
14 24V2 O 24 V DC 24 V DC power to MPPFCL
15 MPF_LIFT_DR_A O 0/24 V DC MPLM: On/Off
16 MPF_LIFT_DR_B O 0/24 V DC MPLM: On/Off
YC7 1 24V2 O 24 V DC 24 V DC power to DUCL2
Connected to 2 DU_CL2_REM O 0/24 V DC DUCL2: On/Off
duplex clutch 3 DU_OPEN I 0/3.3 V DC DUCSW: On/Off
2, duplex
cover switch 4 GND - - Ground
and duplex 5 DU2_B/ O 0/24 V DC (pulse) DUM2 drive control signal
motor 2
Connected to 2 DU_SENS I 0/3.3 V DC DUS2: On/Off
duplex sen- 3 5V O 5 V DC 5 V DC power to DUS2
sor 2
2-3-83
2LK/2LN/2LM/2LC

YC10 1 LOOP_SENS I 0/3.3 V DC LPS: On/Off
loop sensor
3 5V O 5 V DC 5 V DC power to LPS
4 3.3V - - Not used
5 REG_BK_LED - - Not used
6 GND - - Not used
_P
_S
9 GND - - Not used
11 5V - - Not used
Connected to 2 DU_ENTER_SEN I 0/3.3 V DC DUS1: On/Off
duplex sen- S
sor 1, eject
3 5V O 5 V DC 5 V DC power to DUS1
fan motor
and duplex 4 EXIT_FAN_REM O 0/24 V DC EFM1: On/Off
clutch 1 5 24V2 O 24 V DC 24 V DC power to EFM1
6 EXIT_FAN_REM O 0/24 V DC EFM2: On/Off
7 24V2 O 24 V DC 24 V DC power to EFM2
8 24V2 O 24 V DC 24 V DC power to DUCL1
9 DU_CL_UPPER_ O 0/24 V DC DUCL1: On/Off
REM
feed PWB 1
3 MPF_TABLE O 0/3.3 V DC MPTSW: On/Off
7 MPF_LNG O 0/3.3 V DC MPPLSW: On/Off
8 LED_3.3V3 I 3.3 V DC 3.3 V DC power from FPWB1
9 MPF_PPR_SET O 0/3.3 V DC MPPS: On/Off
10 MPF_LIFT_UP_S O 0/3.3 V DC MPLS1: On/Off
ENS
11 MPF_LIFT_DOW O 0/3.3 V DC MPLS2: On/Off
N_SENS
12 MPF_JAM_SENS O 0/3.3 V DC MPFS: On/Off
2-3-84
2LK/2LN/2LM/2LC

YC12 13 MPF_CL_REM I 0/24 V DC MPPFCL: On/Off
Connected to 14 24V2 I 24 V DC 24 V DC power from FPWB1
feed PWB 1
15 MPF_LIFT_MOT_ I 0/24 V DC MPLM: On/Off
A
16 MPF_LIFT_MOT_ I 0/24 V DC MPLM: On/Off
B
_A
_B
L
YC13 1 3.3V I 3.3 V DC 3.3 V DC power from FPWB1
Connected to 2 LOOP_SENS I 0/3.3 V DC LPS: On/Off
feed PWB 1 3 EDGE_FAN_REM I 0/24 V DC FUFM: On/Off
4 DU1_A I 0/24 V DC (pulse) DUM1 drive control signal
5 DU1_B I 0/24 V DC (pulse) DUM1 drive control signal
6 DU1_A/ I 0/24 V DC (pulse) DUM1 drive control signal
7 DU1_B/ I 0/24 V DC (pulse) DUM1 drive control signal
8 GND - - Ground
9 DU_CL_UPPER_ I 0/24 V DC DUCL1: On/Off
REM
10 24V2 I 24 V DC 24 V DC power from FPWB1
11 EXIT_FAN I 0/24 V DC EFM: On/Off
12 DU_ENTER_SEN O 0/3.3 V DC DUS1: On/Off
S
Connected to 2 PRESS_RLS_SE I 0/3.3 V DC TRRS: On/Off
transfer NS
release sen- 3 5V O 5 V DC 5 V DC power to TRRS
sor and
transfer 4 PRESS_RLS_RE O 0/24 V DC TRRM: On/Off
release M1
motor 5 PRESS_RLS_RE O 0/24 V DC TRRM: On/Off
M2
6 NC - - Not used
2-3-85
2LK/2LN/2LM/2LC

YC16 1 DU1_B/ O 0/24 V DC (pulse) DUM1 drive control signal
Connected to 2 DU1_A/ O 0/24 V DC (pulse) DUM1 drive control signal
duplex motor
1 and fuser
fan motor 1/2 4 DU1_A O 0/24 V DC (pulse) DUM1 drive control signal
5 EDGE_FAN_REM O 0/24 V DC FUFM1: On/Off
6 24V2 O 24 V DC 24 V DC power to FUFM1
7 EDGE_FAN_REM O 0/24 V DC FUFM2: On/Off
8 24V2 O 24 V DC 24 V DC power to FUFM2
2-3-86
2LK/2LN/2LM/2LC
2-3-10 Motor control PWB
1 24
YC5
22
14
YC3
YC7
12
11
1
14
10
YC1
YC6
1
1 YC4 24
1 YC2 6
Figure 2-3-11 Motor control PWB silk-screen diagram
2-3-87
2LK/2LN/2LM/2LC

power source
3 GND - - Ground
PWB
YC3 1 DRM_INDEX_C I 0/3.3 V DC DRM-C control signal
Connected to 2 DRM_INDEX_M I 0/3.3 V DC DRM-M control signal
engine PWB
3 DRM_INDEX_BK I 0/3.3 V DC DRM-K control signal
4 BLT_INDEX - - Not used
5 BLT_SPEED I 0/3.3 V DC TBLS: On/Off
6 EMERGENCY I 0/3.3 V DC MCPWB control signal
7 ENG_RDY O 0/3.3 V DC MCPWB ready signal
8 ENG_SDO O 0/3.3 V DC (pulse) MCPWB serial communication data
signal
9 ENG_SEL I 0/3.3 V DC MCPWB select signal
10 ENG_SDI I 0/3.3 V DC (pulse) MCPWB serial communication data
signal
11 ENG_CLK I 0/3.3 V DC (pulse) MCPWB clock signal
12 BLT_FG - - Not used
13 MOT_ON I 0/3.3 V DC MCPWB control signal
14 MOT_DATA_SET I 0/3.3 V DC MCPWB control signal
15 BLT_REM - - Not used
16 BLT_VM - - Not used
17 BLT_BRAKE - - Not used
18 +5V I 5 V DC 5 V DC power to MCPWB
19 +5V I 5 V DC 5 V DC power to MCPWB
20 GND - - Ground
21 GND - - Ground
22 DRM_INDEX_Y I 0/3.3 V DC DRM-Y control signal
2-3-88
2LK/2LN/2LM/2LC

drum motor
3 NC - - Not used
C/Y
4 NC - - Not used
5 NC - - Not used
6 NC - - Not used
7 NC - - Not used
8 NC - - Not used
9 DRM_C_BRAKE - - Not used
10 DRM_Y_BRAKE - - Not used
11 DRM_C_GAIN - - Not used
12 DRM_Y_GAIN - - Not used
13 DRM_C_CW/ O 0/24 V DC DRM-C: On/Off
CCW
14 DRM_Y_CW/ O 0/24 V DC DRM-Y: On/Off
CCW
15 DRM_C_LD O 0/3.3 V DC DRM-C control signal
16 DRM_Y_LD O 0/3.3 V DC DRM-Y control signal
17 DRM_C_CLK O 0/3.3 V DC (pulse) DRM-C clock signal
18 DRM_Y_CLK O 0/3.3 V DC (pulse) DRM-Y clock signal
19 DRM_C_S/S O 0/3.3 V DC DRM-C control signal
20 DRM_Y_S/S O 0/3.3 V DC DRM-Y control signal
21 PGND - - Ground
22 PGND - - Ground
23 +24V1 O 24 V DC 24 V DC power to DRM-C
24 +24V1 O 24 V DC 24 V DC power to DRM-Y
drum motor 3 NC - - Not used
K/M
4 NC - - Not used
5 NC - - Not used
6 NC - - Not used
7 NC - - Not used
8 NC - - Not used
9 DRM_BK_BRAKE - - Not used
10 DRM_M_BRAKE - - Not used
11 DRM_BK_GAIN - - Not used
2-3-89
2LK/2LN/2LM/2LC

YC5 12 DRM_M_GAIN - - Not used
Connected to 13 DRM_BK_CW/ O 0/24 V DC DRM-K: On/Off
drum motor CCW
K/M 14 DRM_M_CW/ O 0/24 V DC DRM-M: On/Off
CCW
15 DRM_BK_LD O 0/3.3 V DC DRM-K control signal
16 DRM_M_LD O 0/3.3 V DC DRM-M control signal
17 DRM_BK_CLK O 0/3.3 V DC (pulse) DRM-K clock signal
18 DRM_M_CLK O 0/3.3 V DC (pulse) DRM-M clock signal
19 DRM_BK_S/S O 0/3.3 V DC DRM-K control signal
20 DRM_M_S/S O 0/3.3 V DC DRM-M control signal
21 PGND - - Ground
22 PGND - - Ground
23 +24V1 O 24 V DC 24 V DC power to DRM-K
24 +24V1 O 24 V DC 24 V DC power to DRM-M
YC7 1 DLP_M_GAIN - - Not used
Connected to 2 DLP_M_CW/CCW O 0/24 V DC DEVM-MCY: On/Off
developer
3 DLP_M_LD O 0/3.3 V DC DEVM-MCY control signal
motor MCY/K
4 DLP_M_CLK O 0/3.3 V DC (pulse) DEVM-MCY clock signal
5 DLP_M_S/S O 0/3.3 V DC DEVM-MCY control signal
6 PGND - - Ground
7 +24V1 O 24 V DC 24 V DC power to DEVM-MCY
8 DLP_BK_GAIN - - Not used
9 DLP_BK_CW/ O 0/24 V DC DEVM-K: On/Off
CCW
10 DLP_BK_LD O 0/3.3 V DC DEVM-K control signal
11 DLP_BK_CLK O 0/3.3 V DC (pulse) DEVM-K clock signal
12 DLP_BK_S/S O 0/3.3 V DC DEVM-K control signal
13 PGND - - Ground
14 +24V1 O 24 V DC 24 V DC power to DRM-K
2-3-90
2LK/2LN/2LM/2LC
2-3-11 LSU relay PWB
10
YC3
1
5
YC4
1
10
YC5
15
YC6
1
10
YC7
1
5
YC8
1
10
YC9
1
YC10
YC2
1
60 1
YC1
8 1
Figure 2-3-12 LSU relay PWB silk-screen diagram
2-3-91
2LK/2LN/2LM/2LC

YC1 1 +24V1 O 24 V DC 24 V DC power from PSPWB
Connected to 2 +24V1 O 24 V DC 24 V DC power from PSPWB
power source
3 GND - - Ground
PWB and
5 +5V1 O 5 V DC 5 V DC power from EPWB
6 +5V1 O 5 V DC 5 V DC power from EPWB
7 GND - - Ground
8 GND - - Ground
9 +3.3V2 O 3.3 V DC 3.3 V DC power from EPWB
10 GND - - Ground
Connected to 2 CLK I 0/3.3 V DC (pulse) Clock signal
engine PWB
3 SGND - - Ground
4 SDI O 0/3.3 V DC (pulse) Serial communication data signal
5 SGND - - Ground
6 SDO I 0/3.3 V DC (pulse) Serial communication data signal
7 SGND - - Ground
8 MSET_N I 0/3.3 V DC Control signal
9 SGND - - Ground
10 LDD_CS 1 Y I 0/3.3 V DC APCPWB-Y control signal
11 EEPROM CS Y I/O 0/3.3 V DC (pulse) APCPWB-Y EEPROM data signal
12 LDD_CS 1 C I 0/3.3 V DC APCPWB-C control signal
13 EEPROM CS C I/O 0/3.3 V DC (pulse) APCPWB-C EEPROM data signal
14 LDD_CS 1 M I 0/3.3 V DC APCPWB-M control signal
15 EEPROM CS M I/O 0/3.3 V DC (pulse) APCPWB-M EEPROM data signal
16 LDD_CS 2 Bk I 0/3.3 V DC APCPWB-K control signal
17 EEPROM CS 2 Bk I/O 0/3.3 V DC (pulse) APCPWB-K EEPROM data signal
18 LDD_CS 1 Bk I 0/3.3 V DC APCPWB-K control signal
20 SGND - - Ground
21 INT_ST 1 Y I 0/3.3 V DC APCPWB-Y control signal
22 PALA_SIG P0 Y I 0/3.3 V DC APCPWB-Y control signal
25 GAIN FIX Y I 0/3.3 V DC APCPWB-Y control signal
26 SGND - - Ground
2-3-92
2LK/2LN/2LM/2LC

YC2 27 DATA_2N_Y(LVD I 0/3.3 V DC (pulse) Video data signal Y (N)
S)
Connected to 28 DATA_2P_Y(LVD I 0/3.3 V DC (pulse) Video data signal Y (P)
engine PWB S)
29 SGND - - Ground
30 INT_ST 1 C I 0/3.3 V DC APCPWB-C control signal
31 PALA_SIG P0 C I 0/3.3 V DC APCPWB-C control signal
34 GAIN FIX C I 0/3.3 V DC APCPWB-C control signal
35 SGND - - Ground
36 DATA_2N_C(LVD I 0/3.3 V DC (pulse) Video data signal C (N)
S)
37 DATA_2P_C(LVD I 0/3.3 V DC (pulse) Video data signal C (P)
S)
38 SGND - - Ground
39 INT_ST 1 M I 0/3.3 V DC APCPWB-M control signal
40 PALA_SIG P0 M I 0/3.3 V DC APCPWB-M control signal
43 GAIN FIX M I 0/3.3 V DC APCPWB-M control signal
44 SGND - - Ground
45 DATA_2N_M(LVD I 0/3.3 V DC (pulse) Video data signal M (N)
S)
46 DATA_2P_M(LVD I 0/3.3 V DC (pulse) Video data signal M (P)
S)
47 SGND - - Ground
48 DATA_3NBk(LVD I 0/3.3 V DC (pulse) Video data signal K (N)
S)
49 DATA_3PBk(LVD I 0/3.3 V DC (pulse) Video data signal K (P)
S)
50 SGND - - Ground
S)
S)
53 SGND - - Ground
54 PALA_SIG I 0/3.3 V DC APCPWB-K control signal
P3_2Bk
2-3-93
2LK/2LN/2LM/2LC

YC2 55 INT_ST 2 Bk I 0/3.3 V DC APCPWB-K control signal
Connected to 56 INT_ST 1 Bk I 0/3.3 V DC APCPWB-K control signal
engine PWB
57 PALA_SIG P0 Bk I 0/3.3 V DC APCPWB-K control signal
60 GAIN FIX Bk I 0/3.3 V DC APCPWB-K control signal
61 SGND - - Ground
S)
S)
64 SGND - - Ground
Connected to 2 BD Y O 0/3.3 V DC (pulse) Horizontal synchronization signal Y
engine PWB
3 LSU_TH Y O Analog LSU thermistor Y detection signal
4 CUALM Y O 0/3.3 V DC APCPWB-Y alarm signal
7 SGND - - Ground
8 SDCLK Y I 0/3.3 V DC (pulse) APCPWB-Y clock signal
9 SGND - - Ground
10 DATA_1N_Y(LVD I 0/3.3 V DC (pulse) Video data signal Y (N)
S)
11 DATA_1P_Y(LVD I 0/3.3 V DC (pulse) Video data signal Y (P)
S)
12 SGND - - Ground
13 REM Y I 0/24 V DC PM-Y: On/Off
14 LOCK Y O 0/3.3 V DC PM-Y lock signal
15 CLK Y I 0/3.3 V DC (pulse) PM-Y clock signal
16 SGND - - Ground
17 BD C O 0/3.3 V DC (pulse) Horizontal synchronization signal C
18 LSU_TH C O Analog LSU thermistor C detection signal
19 CUALM C O 0/3.3 V DC APCPWB-C alarm signal
22 SGND - - Ground
23 SDCLK C I 0/3.3 V DC (pulse) APCPWB-C clock signal
24 SGND - - Ground
2-3-94
2LK/2LN/2LM/2LC

YC3 25 DATA_1N_C(LVD I 0/3.3 V DC (pulse) Video data signal C (N)
S)
Connected to 26 DATA_1P_C(LVD I 0/3.3 V DC (pulse) Video data signal C (P)
engine PWB S)
27 SGND - - Ground
28 REM C I 0/24 V DC PM-C: On/Off
29 LOCK C O 0/3.3 V DC PM-C lock signal
30 CLK C I 0/3.3 V DC (pulse) PM-C clock signal
31 SGND - - Ground
32 BD M O 0/3.3 V DC (pulse) Horizontal synchronization signal M
33 LSU_TH M O Analog LSU thermistor M detection signal
34 CUALM M O 0/3.3 V DC APCPWB-M alarm signal
37 SGND - - Ground
38 SDCLK M I 0/3.3 V DC (pulse) APCPWB-M clock signal
39 SGND - - Ground
40 DATA_1N_M(LVD I 0/3.3 V DC (pulse) Video data signal M (N)
S)
41 DATA_1P_M(LVD I 0/3.3 V DC (pulse) Video data signal M (P)
S)
42 SGND - - Ground
43 REM M I 0/24 V DC PM-M: On/Off
44 LOCK M O 0/3.3 V DC PM-M lock signal
45 CLK M I 0/3.3 V DC (pulse) PM-M clock signal
46 SGND - - Ground
47 BD Bk O 0/3.3 V DC (pulse) Horizontal synchronization signal K
48 LSU_TH Bk O Analog LSU thermistor K detection signal
49 CUALM Bk O 0/3.3 V DC APCPWB-K alarm signal
52 SGND - - Ground
53 SDCLK Bk I 0/3.3 V DC (pulse) APCPWB-K clock signal
54 SGND - - Ground
S)
S)
2-3-95
2LK/2LN/2LM/2LC

Connected to 58 REM Bk I 0/24 V DC PM-K: On/Off
engine PWB
59 LOCK Bk O 0/3.3 V DC PM-K lock signal
60 CLK Bk I 0/3.3 V DC (pulse) PM-K clock signal
YC4 1 24V O 24 V DC 24 V DC power to PM-K
Connected to 2 PGND - - Ground
polygon
3 REM Bk O 0/24 V DC PM-K: On/Off
motor K
4 LOCK Bk I 0/3.3 V DC PM-K lock signal
5 CLK Bk O 0/3.3 V DC (pulse) PM-K clock signal
Connected to 2 BD Bk I 0/3.3 V DC (pulse) Horizontal synchronization signal K
APC PWB K
3 LSU_TH Bk I Analog LSU thermistor K detection signal
4 PALA_SIG - - Not used
P3_2Bk
5 LDD_CS 2 Bk - - Not used
6 5V O 5 V DC 5 V DC power to APCPWB-K
9 LDD_CS 1 Bk O 0/3.3 V DC APCPWB-K control signal
10 SDI1 I 0/3.3 V DC (pulse) Serial communication data signal
11 SDO1 O 0/3.3 V DC (pulse) Serial communication data signal
12 CLK1 O 0/3.3 V DC (pulse) APCPWB-K clock signal
14 MSET_N O 0/3.3 V DC APCPWB-K control signal
15 CUALM Bk I 0/3.3 V DC APCPWB-K alarm signal
16 INT_ST 2 Bk O 0/3.3 V DC APCPWB-K control signal
17 INT_ST 1 Bk O 0/3.3 V DC APCPWB-K control signal
18 PALA_SIG P0 Bk O 0/3.3 V DC APCPWB-K control signal
23 SDCLK Bk O 0/3.3 V DC (pulse) APCPWB-K clock signal
24 GAIN FIX Bk O 0/3.3 V DC APCPWB-K control signal
25 DATA_1NBk(LVD O 0/3.3 V DC (pulse) Video data signal K (N)
S)
26 DATA_1PBk(LVD O 0/3.3 V DC (pulse) Video data signal K (P)
S)
2-3-96
2LK/2LN/2LM/2LC

Connected to 28 DATA_2NBk(LVD O 0/3.3 V DC (pulse) Video data signal K (N)
APC PWB K S)
29 DATA_2PBk(LVD O 0/3.3 V DC (pulse) Video data signal K (P)
S)
30 SGND - - Ground
YC7 1 24V O 24 V DC 24 V DC power to PM-M
polygon
3 REM M O 0/24 V DC PM-M: On/Off
motor M
4 LOCK M I 0/3.3 V DC PM-M lock signal
5 CLK M O 0/3.3 V DC (pulse) PM-M clock signal
Connected to 2 BD M I 0/3.3 V DC (pulse) Horizontal synchronization signal M
APC PWB M 3 LSU_TH M I Analog LSU thermistor M detection signal
4 - - - Not used
5 - - - Not used
6 5V O 5 V DC 5 V DC power to APCPWB-M
9 LDD_CS 1 M O 0/3.3 V DC APCPWB-M control signal
12 CLK1 O 0/3.3 V DC (pulse) APCPWB-M clock signal
13 EEPROM CS M I/O 0/3.3 V DC (pulse) APCPWB-M EEPROM data signal
14 MSET_N O 0/3.3 V DC APCPWB-M control signal
15 CUALM M I 0/3.3 V DC APCPWB-M alarm signal
16 - O 0/3.3 V DC APCPWB-M control signal
17 INT_ST 1 M O 0/3.3 V DC APCPWB-M control signal
18 PALA_SIG P0 M O 0/3.3 V DC APCPWB-M control signal
23 SDCLK M O 0/3.3 V DC (pulse) APCPWB-M clock signal
24 GAIN FIX M O 0/3.3 V DC APCPWB-M control signal
S)
2-3-97
2LK/2LN/2LM/2LC

YC8 26 DATA_1P_M(LVD O 0/3.3 V DC (pulse) Video data signal M (P)
S)
APC PWB M 28 DATA_2N_M(LVD O 0/3.3 V DC (pulse) Video data signal M (N)
S)
S)
30 SGND - - Ground
YC9 1 24V O 24 V DC 24 V DC power to PM-C
polygon
3 REM C O 0/24 V DC PM-C: On/Off
motor C
4 LOCK C I 0/3.3 V DC PM-C lock signal
5 CLK C O 0/3.3 V DC (pulse) PM-C clock signal
Connected to 2 BD C I 0/3.3 V DC (pulse) Horizontal synchronization signal C
APC PWB C 3 LSU_TH C I Analog LSU thermistor C detection signal
4 - - - Not used
5 - - - Not used
6 5V O 5 V DC 5 V DC power to APCPWB-C
9 LDD_CS 1 C O 0/3.3 V DC APCPWB-C control signal
12 CLK1 O 0/3.3 V DC (pulse) APCPWB-C clock signal
13 EEPROM CS C I/O 0/3.3 V DC (pulse) APCPWB-C EEPROM data signal
14 MSET_N O 0/3.3 V DC APCPWB-C control signal
15 CUALM C I 0/3.3 V DC APCPWB-C alarm signal
16 - O 0/3.3 V DC APCPWB-C control signal
17 INT_ST 1 C O 0/3.3 V DC APCPWB-C control signal
18 PALA_SIG P0 C O 0/3.3 V DC APCPWB-C control signal
23 SDCLK C O 0/3.3 V DC (pulse) APCPWB-C clock signal
24 GAIN FIX C O 0/3.3 V DC APCPWB-C control signal
2-3-98
2LK/2LN/2LM/2LC

YC10 25 DATA_1N_C(LVD O 0/3.3 V DC (pulse) Video data signal C (N)
S)
Connected to 26 DATA_1P_C(LVD O 0/3.3 V DC (pulse) Video data signal C (P)
APC PWB C S)
27 SGND - - Ground
28 DATA_2N_C(LVD O 0/3.3 V DC (pulse) Video data signal C (N)
S)
S)
30 SGND - - Ground
YC11 1 24V O 24 V DC 24 V DC power to PM-Y
polygon
3 REM Y O 0/24 V DC PM-Y: On/Off
motor Y
4 LOCK Y I 0/3.3 V DC PM-Y lock signal
5 CLK Y O 0/3.3 V DC (pulse) PM-Y clock signal
Connected to 2 BD Y I 0/3.3 V DC (pulse) Horizontal synchronization signal Y
APC PWB Y 3 LSU_TH Y I Analog LSU thermistor Y detection signal
4 - - - Not used
5 - - - Not used
6 5V O 5 V DC 5 V DC power to APCPWB-Y
9 LDD_CS 1 Y O 0/3.3 V DC APCPWB-Y control signal
12 CLK1 O 0/3.3 V DC (pulse) APCPWB-Y clock signal
13 EEPROM CS Y I/O 0/3.3 V DC (pulse) APCPWB-Y EEPROM data signal
14 MSET_N O 0/3.3 V DC APCPWB-Y control signal
15 CUALM Y I 0/3.3 V DC APCPWB-Y alarm signal
16 - O 0/3.3 V DC APCPWB-Y control signal
17 INT_ST 1 Y O 0/3.3 V DC APCPWB-Y control signal
18 PALA_SIG P0 Y O 0/3.3 V DC APCPWB-Y control signal
23 SDCLK Y O 0/3.3 V DC (pulse) APCPWB-Y clock signal
2-3-99
2LK/2LN/2LM/2LC

YC12 24 GAIN FIX Y O 0/3.3 V DC APCPWB-Y control signal
Connected to 25 DATA_1N_Y(LVD O 0/3.3 V DC (pulse) Video data signal Y (N)
APC PWB Y S)
S)
27 SGND - - Ground
S)
S)
30 SGND - - Ground
2-3-100
2LK/2LN/2LM/2LC
2-4-1 Appendixes
2-4 Appendixes
(1) Maintenance kits

Maintenance part name Alternative

Parts No.
Name used in service Name used in parts list part No.
MK-8305A/Maintenance kit MK-8305A/MAINTENANCE KIT 1702LK0UN0 072LK0UN

(600,000 pages)
Drum unit K DK-8505 (K) - -
Developing unit K DV-8305K - -
Transfer belt unit TR-8505 - -
Transfer roller PARTS ROLLER SECONDLY - -
TRANSFER SP
MK-8305B/Maintenance kit MK-8305B/MAINTENANCE KIT 1702LK0UN1 072LK0U1
(600,000 pages)
Drum unit C DK-8505 (C) - -
Drum unit M DK-8505 (M) - -
Drum unit Y DK-8505 (Y) - -
Developing unit C DV-8305C - -
Developing unit M DV-8305M - -
Developing unit Y DV-8305Y - -
MK-8305C/Maintenance kit MK-8305C/MAINTENANCE KIT 1702LK0UN2 072LK0U2
(300,000 pages)
Fuser unit FK-UNIT - -
2-4-1
2LK/2LN/2LM/2LC
Maintenance part name Alternative

Parts No.
Name used in service Name used in parts list part No.
MK-8505A/Maintenance kit MK-8505A/MAINTENANCE KIT 1702LC0UN0 072LC0UN

(600,000 pages)
Drum unit K DK-8505 (K) - -
Developing unit K DV-8505K - -
Transfer belt unit TR-8505 - -
Transfer roller PARTS ROLLER SECONDLY - -
TRANSFER SP
MK-8505B/Maintenance kit MK-8505B/MAINTENANCE KIT 1702LC0UN1 072LC0U1
(600,000 pages)
Drum unit C DK-8505 (C) - -
Drum unit M DK-8505 (M) - -
Drum unit Y DK-8505 (Y) - -
Developing unit C DV-8505C - -
Developing unit M DV-8505M - -
Developing unit Y DV-8505Y - -
MK-8505C/Maintenance kit MK-8505C/MAINTENANCE KIT 1702LC0UN2 072LC0U2
(300,000 pages)
Fuser unit FK-UNIT - -
2-4-2
2LK/2LN/2LM/2LC
(2) Repetitive defects gauge
First occurrence of defect
37.5 mm/1 1/2" Carger roller

39 mm/1 9/16" Magnet roller
Sleeve roller
57 mm/2 1/4" Right registration roller

63 mm/2 1/2" Left registration roller
75 mm/2 15/16" Transfer roller
94 mm/3 11/16" Drum

94.2 mm/3 11/16" Press roller (30 ppm/35 ppm)
109.9 mm/4 5/16" Press roller (45 ppm/55 ppm)
127.5 mm/5" Heat roller
936 mm/36 7/8" Transfer belt
2-4-3
2LK/2LN/2LM/2LC
(3) Firmware environment commands

The printer maintains a number of printing parameters in its memory. There parameters may be changed per-
manently with the FRPO (Firmware RePrOgram) commands.
This section provides information on how to use the FRPO command and its parameters using examples.
Using FRPO commands for reprogramming firmware

The current settings of the FRPO parameters are listed as optional values on the service status page.
Note: Before changing any FRPO parameter, print out a service status page, so you will know the parameter
values before the changes are made. To return FRPO parameters to their factory default values, send the
FRPO INIT (FRPO-INITialize) command.(!R! FRPO INIT; EXIT;)
The FRPO command is sent to the printer in the following sequence:

!R! FRPO parameter, value; EXIT;
Example: Changing emulation mode to PCL6
!R! FRPO P1, 6; EXIT;
FRPO parameters
Factory
Item FRPO Setting values
setting
Top margin A1 Integer value in inches 0
A2 Fraction value in 1/100 inches 0
Left margin A3 Integer value in inches 0
Page length A5 Integer value in inches 17
Page width A7 Integer value in inches 17
Default pattern resolution B8 0: 300 dpi 0
1: 600 dpi
Page orientation C1 0: Portrait 0
1: Landscape
Default font No. * C2 Middle two digits of power-up font 0
C3 Last two digits of power-up font 0
C5 First two digits of power-up font 0
PCL font switch C8 0: HP compatibility mode 0
32: Conventional compatibility mode
Total host buffer size H8 0 to 99 in units of the size defined by FRPO S5 5
Form feed time-out value H9 Value in units of 5 seconds (1 to 99) 6
Top margin L1 Top margin (integer value) 0
L2 Top margin (decimal value) 50
Left margin L3 Left margin (integer value) 0
L4 Left margin (decimal value) 50
2-4-4
2LK/2LN/2LM/2LC
Factory
setting
Page length L5 Page length (integer value) 10
L6 Page length (decimal value) 61
Page width L7 Page width (integer value) 8
L8 Page width (decimal value) 11
Duplex mode N4 0: Off 0
1: Long edge binding
2: Short edge binding
Sleep timer time-out time N5 Value in units of 1 minute (1 to 240) 60
Ecoprint level N6 0: Off 0
2: On
Default emulation mode P1 6: PCL 6 120V: 9
9: KPDL 220-240V: 6
Carriage-return action P2 0: Ignores 1
1: Carriage-return
2: Carriage-return + linefeed
Linefeed action P3 0: Ignores 1
1: Linefeed
2: Linefeed + carriage-return
Automatic emulation switching P4 0: AES disabled 120V: 1
1: AES enabled 220-240V: 0
Alternative emulation P5 Same as the P1 values except that 9 is 6
(For KPDL3) ignored.
Automatic emulation switching P7 0: Page eject commands 120V: 11
trigger 1: None 220-240V: 10
2: Page eject and prescribe EXIT commands
3: Prescribe EXIT commands
4: Formfeed (^L) commands
6: Pescribe EXIT and formfeed commands
10: Page eject commands; if AES fails,
resolves to KPDL
Command recognition character P9 ASCII code of 33 to 126 82 (R)
Default stacker R0 1 (inner tray) 1
2-4-5
2LK/2LN/2LM/2LC
Factory
setting
Default paper size R2 0: Size of the default paper cassette (See R4.) 0
1: Monarch (3-7/8 × 7-1/2 inches)
2: Business (4-1/8 × 9-1/2 inches)
3: International DL (11 × 22 cm)
4: International C5 (16.2 × 22.9 cm)
5: Executive (7-1/4 × 10-1/2 inches)
6: US Letter (8-1/2 × 11 inches)
7: US Legal (8-1/2 × 14 inches)
8: A4 (21.0 × 29.7 cm)
9: JIS B5 (18.2 × 25.7 cm)
10: A3 (29.7 ´ 42 cm)
11: B4 (25.7 ´ 36.4 cm)
12: US Ledger (11 ´ 17 inches)
13: ISO A5
14: A6 (10.5 × 14.8 cm)
15: JIS B6 (12.8 × 18.2 cm)
16: Commercial #9 (3-7/8 × 8-7/8 inches)
17: Commercial #6 (3-5/8 × 6-1/2 inches)
18: ISO B5 (17.6 × 25 cm)
19: Custom (11.7 × 17.7 inches)
30: C4 (22.9 ´ 32.4 cm)
31: Hagaki (10 × 14.8 cm)
32: Ofuku-hagaki (14.8 × 20 cm)
33: Officio II
39: 8K
40: 16K
42: 8.5 × 13.5 inches
50: Statement
51: Folio
52: Youkei 2
53: Youkei 4
Default cassette R4 0: MP tray 1
1: Cassette 1
2: Cassette 2
3: Cassette 3
4: Cassette 4
5: Cassette 5
6: Cassette 6
7: Cassette 7
A4/letter equation S4 0: Off 1
1: On
Host buffer size S5 0: 10 KB 1
1: 100 KB
2: 1024 KB
Wide A4 T6 0: Off 0
1: On
Line spacing * U0 Lines per inch (integer value) 6
U1 Lines per inch (decimal value) 0
2-4-6
2LK/2LN/2LM/2LC
Factory
setting
Character spacing * U2 Characters per inch (integer value) 10
U3 Characters per inch (decimal value) 0
Country code U6 0: US-ASCII 41
1: France
2: Germany
3: UK
4: Denmark
5: Sweden
6: Italy
7: Spain
8: Japan
9: US Legal
10: IBM PC-850 (Multilingual)
11: IBM PC-860 (Portuguese)
12: IBM PC-863 (Canadian French)
13: IBM PC-865 (Norwegian)
14: Norway
15: Denmark 2
16: Spain 2
17: Latin America
50 - 99: HP PCL symbol set coding
Code set at power up in U7 0: Same as the default emulation mode (P1) 53
daisywheel emulation 1: IBM
6: IBM PC-8
7 - 99: HP PCL symbol set coding
Font pitch for fixedpitch scalable U8 Default font pitch (integer value) 10
font *
U9 Default font pitch (decimal value) 0
Font height for the default scal- V0 Integer value in 100 points: 0 to 9 0
able font *
V1 Integer value in points: 0 to 99 12
V2 decimal value in 1/100 points: 0, 25, 50, 75 0
Default scalable font * V3 Name of typeface of up to 32 characters, Courier
enclosed with single or double quotation marks
Default weight V9 0: Courier = darkness 5
(courier and letter Gothic) Letter Gothic = darkness
1: Courier = regular
Letter Gothic = darkness
4: Courier = darkness
Letter Gothic = regular
5: Courier = regular
Letter Gothic = regular
Color mode W1 0: Black & white 1
1: Color
Gloss mode W6 0: Low (normal) 0
1: High
2-4-7
2LK/2LN/2LM/2LC
Factory
setting
Paper type for the MP tray X0 1: Plain 1
2: Transparency
3: Preprinted
4: Label
5: Bond
6: Recycle
7: Vellum
9: Letterhead
10: Color
11: Prepunched
12: Envelope
13: Cardstock
14: Coated
16: Thick
17: High quality
21 to 28: Custom1 to 8
Paper type for cassettes 1 and 2 X1 1: Plain 1
X2 3: Preprinted
5: Bond
6: Recycled
7: Vellum
9: Letterhead
10: Color
11: Prepunched
16: Thick
17: High quality
Paper type for optional cassettes X3 1: Plain 1
3 to 7 X4 3: Preprinted
X5 5: Bond
X6 6: Recycled
X10 9: Letterhead
10: Color
11: Prepunched
17: High quality
PCL paper source X9 0: Performs paper selection depending on 0
media type.
1: Performs paper selection depending on
paper sources.
Automatic continue for ‘Press Y0 0: Off 0
GO’ 1: On
Automatic continue timer Y1 Value in units of 5 seconds (1 to 99) 6 (30 s)
Error message for device error Y3 0: Not detect 127
127: Detect
2-4-8
2LK/2LN/2LM/2LC
Factory
setting
Duplex operation for specified Y4 0: Off 0
paper type 1: On
(Prepunched, Preprintedand Let-
terhead)
Default operation for PDF direct Y5 0: Enlarges or reduces the image to fit in the 0
printing current paper size. Loads paper from the
current paper cassette.
1: Through the image. Loads paper which is
the same size as the image.
2: Enlarges or reduces the image to fit in the
current paper size. Loads Letter, A4 size
paper depending on the image size.
3: Through the image. Loads Letter, A4 size
8: Through the image. Loads paper from the
current paper cassette.
9: Through the image. Loads Letter, A4 size
10: Enlarges or reduces the image to fit in the
current paper size. Loads Letter, A4 size
e-MPS error Y6 0: Does not print the error report and display 3
the error message.
1: Prints the error report.
2: Displays the error message.
3: Prints the error report and displays the error
message.
*: Ignored in some emulation modes.
2-4-9
2LK/2LN/2LM/2LC
2-4-10
2LK/2LN/2LM/2LC
(4) Chart of image adjustment procedures

Adjusting Maintenance mode
Item Image Description Original Page Remarks
order Item No. Mode
Adjusting the magnification in the Data processing U039 Horizon U039 test pattern P.1-3-39
main scanning direction (printing
1 adjustment)
Adjusting the magnification in the Data processing U039 Vertical U039 test pattern P.1-3-39
auxiliary scanning direction
2 (printing adjustment)
Adjusting the center line of the MP Adjusting the LSU print start timing U034 LSU Out Left U034 test pattern P.1-3-33 To make an adjustment for duplex copying, select
tray Duplex.
Adjusting the center line of the cas- Adjusting the LSU print start timing U034 LSU Out Left U034 test pattern P.1-3-33
settes
Adjusting the leading edge registra- Registration motor turning on timing U034 LSU Out Top U034 test pattern P.1-3-33 To make an adjustment for duplex copying, select
tion of the MP tray (secondary paper feed start timing) Duplex.
Adjusting the leading edge registra- Registration motor turning on timing U034 LSU Out Top U034 test pattern P.1-3-33
tion of the cassette (secondary paper feed start timing)
Adjusting the leading edge margin LSU illumination start timing U402 Lead U402 test pattern P.1-3-146
(printing adjustment)
7
Adjusting the trailing edge margin LSU illumination end timing U402 Trail U402 test pattern P.1-3-146
(printing adjustment)
8
Adjusting the left and right margins LSU illumination start/end timing U402 A Margin U402 test pattern P.1-3-146
(printing adjustment) C Margin
9
Adjusting magnification of the Data processing U065 Y Scan Zoom Test chart P.1-3-51 U065: For copying an original placed on
scanner in the main scanning direc- the platen.
10 tion U070 Y Scan Zoom P.1-3-56 U070: For copying originals from the DP.
(scanning adjustment)
2-4-11
2LK/2LN/2LM/2LC
Adjusting Maintenance mode

Item Image Description Original Page Remarks
order Item No. Mode
Adjusting magnification of the Original scanning speed U065 X Scan Zoom Test chart P.1-3-51 U065: For copying an original placed on
scanner in the auxiliary scanning the platen.
11 direction U070 X Scan Zoom P.1-3-56 U070: For copying originals from the DP.
(scanning adjustment)
Adjusting the center line Adjusting the original scan data U067 Front Test chart P.1-3-54 U067: For copying an original placed on
(scanning adjustment) (image adjustment) Rotate the platen.
To make an adjustment for rotate copying, select
12 Rotate.
U072 Front P.1-3-60 U072: For copying originals from the DP.
Back To make an adjustment for duplex copying, select
Back.
Adjusting the leading edge registra- Original scan start timing U066 Front Test chart P.1-3-53 U066: For copying an original placed on
tion Rotate the platen.
(scanning adjustment) To make an adjustment for trailing edge registra-
13 tion, select Rotate.
U071 Front Head P.1-3-58 U071: For copying originals from the DP.
Back Head To make an adjustment for duplex copying, select
Back Head.
Adjusting the leading edge margin Adjusting the original scan data U403 B Margin Test chart P.1-3-147 U403: For copying an original placed on
(scanning adjustment) (image adjustment) the contact glass
14 U404 B Margin P.1-3-148 U404: For copying originals from the DP.
Adjusting the trailing edge margin Adjusting the original scan data U403 D Margin Test chart P.1-3-147 U403: For copying an original placed on
(scanning adjustment) (image adjustment) the contact glass
15 U404 D Margin P.1-3-148 U404: For copying originals from the DP.
Adjusting the left and right margins Adjusting the original scan data U403 A Margin Test chart P.1-3-147 U403: For copying an original placed on
(scanning adjustment) (image adjustment) C Margin the contact glass
16 U404 A Margin P.1-3-148 U404: For copying originals from the DP.
C Margin
Image quality
When maintenance item U411 (Automatic adjustment in the scanner) is run using the specified original (P/N 7505000005),
the following adjustments are automatically made: Item Specifications Item Specifications
Adjusting the scanner magnification (U065)
Adjusting the scanner leading edge registration (U066) 100% magnifica- Machine: ± 0.8 % Leading edge Cassette: +1.0/-1.5 mm
Adjusting the scanner center line (U067) tion registration
Using DP: ± 1.5 % MP tray: +1.0/-1.5 mm
When maintenance item U411 (Automatic adjustment in the DP) is run using the specified original (P/N 302AC68243), Enlargement/ Machine: ± 1.0 % Duplex: +1.0/-1.5 mm
the following adjustments are automatically made: reduction
Using DP: ± 1.5 % Skewed paper Cassette: 1.5 mm or less
Adjusting the DP magnification (U070) feed
Adjusting the DP leading edge registration (U071) Lateral square- Machine: ± 1.5 mm/375 mm MP tray: 1.5 mm or less
(left-right differ-
Adjusting the DP center line (U072) ness Using DP: ± 3.0 mm/375 mm Duplex: 2.0 mm or less
ence)
Lateral image Cassette: ± 2.0 mm
shifting
MP tray: ± 2.0 mm
Duplex: ± 3.0 mm
2-4-12
2LK/2LN/2LM/2LC
(5) Wiring diagram

No.1 (30 ppm model/35 ppm model/45 ppm model/55 ppm model)
YC18
DF_CLK 1 1 A1 A1
DF_SDO 2 2 A2 A2
DF_SEL 3 3 A3 A3
DF_SDI 4 4 A4 A4
5V 1 1 5 1 DF_RDY 5 5 A5 A5
BRES Vout 2 2 4 2 DF_DET 6 6 A6 A6
GND 3 3 3 3 GND 7 7 A7 A7
Relay A8 A8
YC20 A9 A9
1 1 2 4 19 1 19 19 N.C A10 A10
BRECSW 2 2 1 5 18 2 18 18 +5V B1 B1 DFEPWB
17 3 17 17 EXIT_SENS 1 1 1 B2 B2
16 4 16 16 GND 2 2 2 B3 B3
15 5 15 15 EXIT_COV_OPEN From PSPWB (3) 3 3 3 B4 B4
14 6 14 14 GND 4 4 4 B5 B5
RET 3 1 13 7 13 13 EXIT_SOL_RET B6 B6
BRSOL ACT
COM
2
1
Relay 2
3
12
11
8
9
12
11
12
11
EXIT_SOL_REM
+24V1
B7
B8
B7
B8
B9 B9
B10 B10
YC4 YC2
GND 3 3 1 1 GND DECAL DIR 1 10 10 10 10 DECAL_DIR
BRCS2 Vout 2 2 2 2 BRIDGE_SENS2 DECAL PD 2 9 11 9 9 DECAL_PD
5V 1 1 3 3 +5V DECAL CLK 3 8 12 8 8 DECAL_CLK
DECAL MODE 4 7 13 7 7 DECAL_PH
DECAL REM 5 6 14 6 6 DECAL_REM
YC6 GUIDE DIR 6 5 15 5 5 GUIDE_DIR Document finisher (option)
GND 3 3 1 1 GND GUIDE PD 7 4 16 4 4 GUIDE_PD
BRCS1 Vout 2 2 2 2 BRIDGE_SENS 1 GUIDE CLK 8 3 17 3 3 GUIDE_CLK
5V 1 1 3 3 +5V GUIDE REM 9 2 18 2 2 GUIDE_REM
Connector holder
Connector holder
Connector holder
DECAL_HP_SENS 10 1 19 1 1 DECAL_HP_SENS
1 1 4 4 GND
BRCSW
Relay
2 2 5 5 BRIDGE_OPEN
6 6 +5V YC1 Paper feeder (option)
7 7 NC +24V 1 1 19 1 19 38 +24V1
+24V 2 2 18 2 18 37 +24V1
YC7 GND 3 3 17 3 17 36 GND
/B 4 4 1 1 BRIDGE1_B/ GND 4 4 16 4 16 35 GND
/A 3 3 2 2 BRIDGE1_A/ +5V 5 5 15 5 15 34 5V
BRCM1 B 2 2 3 3 BRIDGE1_B GND 6 6 14 6 14 33 GND 1 1 1
A 1 1 4 4 BRIDGE1_A
From PSPWB (2)
2 2 2 PFCH
YC3
/B 4 4 5 5 BRIDGE2_B/ BRIDGE_SENS 1 1 1 13 7 13 32 BRIDGE_SENS 1
/A 3 3 6 6 BRIDGE2_A/ BRIDGE OPEN 2 2 12 8 12 31 BRIDGE_OPEN
BRCM2 B 2 2 7 7 BRIDGE2_B BRIDGE_SENS 2 3 3 11 9 11 30 BRIDGE_SENS 2
A 1 1 8 8 BRIDGE2_A BRIDGE1 DIR 4 4 10 10 10 29 BRIDGE1 DIR
BRIDGE1 PD 5 5 9 11 9 28 BRIDGE1 PD
BRIDGE1 CLK 6 6 8 12 8 27 BRIDGE1 CLK YC49 1 1 1
YC8 BRIDGE1 MODE 7 7 7 13 7 26 BRIDGE1 PH 24VC 1 From PSPWB (1) 2 2 2
1 NC BRIDGE1 REM 8 8 6 14 6 25 BRIDGE1 REM GND 2 3 3 3
2 GND BRIDGE2 DIR 9 9 5 15 5 24 BRIDGE2 DIR SIG 3 4 4 4
3 DECAL_HP_SENS BRIDGE2 PD 10 10 4 16 4 23 BRIDGE2 PD
4 +5V BRIDGE2 CLK 11 11 3 17 3 22 BRIDGE2 CLK
BRIDGE2 MODE 12 12 2 18 2 21 BRIDGE2 PH YC19
BRIDGE2 REM 13 13 1 19 1 20 BRIDGE2 REM PF_CLK A1 A1 A11 A1 A1 A1
YC5 PF_SDO A2 A2 A10 A2 A2 A2
1 DECAL_B/ PF_SEL A3 A3 A9 A3 A3 A3
2 DECAL_A/ PF_SDI A4 A4 A8 A4 A4 A4
3 DECAL_B PF_RDY A5 A5 A7 A5 A5 A5
4 DECAL_A PF_PAUSE A6 A6 A6 A6 A6 A6
PF_CAS1_OPEN A7 A7 A5 A7 A7 A7
BRPWB PF_CAS2_OPEN A8 A8 A4 A8 A8 A8 PFEPWB
+3.3V4 A9 A9 A3 A9 A9 A9
5 GUIDE_B/ GND A10 A10 A2 A10 A10 A10
Connector holder
Connector holder
6 GUIDE_A/ GND A11 A11 A1 A11 A11 A11
7 GUIDE_B A12 A12
GUIDE_A
Relay
8 A13 A13
BRIDGE UNIT A14 A14
TN_FAN1 A12 A12 B11 B1 B1 B1
+24V1 A13 A13 B10 B2 B2 B2
B9 B3 B3 B3
TN_FAN2 A14 A14 B8 B4 B4 B4
+24V1 A15 A15 B7 B5 B5 B5
B6 B6 B6 B6
LVU_FAN1 A16 A16 B5 B7 B7 B7
+24V1 A17 A17 B4 B8 B8 B8
B3 B9 B9 B9
KEY COUNTER YC24 LVU_FAN2 A18 A18 B2 B10 B10 B10
1 4 4 +24V1 +24V1 A19 A19 B1 B11 B11 B11
(option)
Connector holder
2 3 3 DC1_COUNT B12 B12
KEY COUNTER 3 2 2 DC1_SET B13 B13
4 1 1 GND B14 B14
5 1 2 1 -
SIDE_CLK B1 B1 4 2 1 Relay 2 + TFM1
SIDE_SDO B2 B2 Relay
SIDE_SEL B3 B3 3 3 2 1 -
KEY CARD (option for JAPAN only) SIDE_SDI B4 B4 2 4 1
Relay
2 + TFM2
YC25 EPWB SIDE_RDY B5 B5 1 5
A1 A1 +5V SIDE_PAUSE B6 B6
A2 A2 +5V TANDEM_CAS1_OPEN B7 B7
A3 A3 +5V TANDEM_CAS2_OPEN B8 B8
A4 A4 +5V SIDE_MULTI_OPEN B9 B9
A5 A5 +5V +3.3V4 B10 B10
A6 A6 +5V GND B11 B11
A7 A7 +5V
Connector holder
A8 A8 +5V +24V1 B12 B12 4 1 1 2 +

A9 A9 COPY_ENABLE BELT_FAN1 B13 B13 3 2 2 Relay 1 - BLFM1
KEY CARD A10 A10 +24V
Relay
MK-2 B1
B2
B1
B2
KEY7
KEY6 +24V1 B14 B14 2 3 1 2 +
B3 B3 KEY5 BELT_FAN2 B15 B15 1 4 2
Relay
1 - BLFM2
B4 B4 KEY4
B5 B5 KEY3
B6 B6 KEY2 DLP_FAN1 B16 B16
B7 B7 KEY1 +24V1 B17 B17
B8 B8 KEY0
B9 B9 GND
FG B10 B10 COUNT DLP_FAN2 B18 B18
+24V1 B19 B19
COIN VENDER (option) YC23

1 1 1 1 +24V
2 2 2 2 GND
3 3 3 3 GND
4 4 4 4 COIN_EN
5 5 5 5 FGND
Relay
6 6 6 6 FEED_COUNT
COIN VENDER 7 7 7 7 EJECT_COUNT
8 8 8 8 COPYING_SIG
9 9 9 9 TXD_COIN
10 10 10 10 GND
11 11 11 11 RXD_COIN
12 12 12 12 GND
2-4-13
2LK/2LN/2LM/2LC
No.2 (30 ppm model)
YC11
SGND 64
CLK 63
SGND 62
SDI 61 YC2
SGND 60 YC3
SDO 59 GND 1 1 4 4 GND GND 1 1 4 4 GND
SGND 58 TH 2 2 3 3 TH TH 2 2 3 3 TH
MSET_N 57 BD 3 3 2 2 PD PDPWB-K PD 3 3 2 2 PD PDPWB-C
SGND 56 +5V 4 4 1 1 +5V +5V 4 4 1 1 +5V
IDD_CS_Y 55
EEPROM_CS_Y 54
IDD_CS_C 53
EEPROM_CS_C 52
IDD_CS_M 51
EEPROM_CS_M 50 APCPWB-K APCPWB-C
IDD_CS_2_BK 49
EEPROM_CS_2_BK 48
IDD_CS_1_BK 47
EEPROM_CS_1_BK 46
SGND 45
INT_ST_Y 44
PALA_STG_P0_Y 43
PALA_STG_P1_Y 42
PALA_STG P2_Y 41 YC3 YC1 YC7 YC1
GAIN_FIX_Y 40 SGND 1 1 10 10 SGND SGND 1 1 10 10 SGND
SGND 39 BD_BK 2 2 9 9 BD_BK BD_C 2 2 9 9 BD_C
DATA_2N_Y(LVDS) 38 LSU_TH_BK 3 3 8 8 LSU_TH_BK LSU_TH_C 3 3 8 8 LSU_TH_C
DATA_2P_Y(LVDS) 37 5V 4 4 7 7 5V 5V 4 4 7 7 5V
SGND 36 NC 5 5 6 6 NC NC 5 5 6 6 NC
INT_ST_ C 35 ENABLE_BK 6 6 5 5 ENABLE_BK ENABLE_C 6 6 5 5 ENABLE_C
PALA_STG_P0_C 34 S/H_BK 7 7 4 4 S/H_BK S/H_C 7 7 4 4 S/H_C
PALA_STG_P1_C 33 VCONT_BK 8 8 3 3 VCONT_BK VCONT_C 8 8 3 3 VCONT_C
PALA_STG_P2_C 32 DATA_1N_BK(LVDS) 9 9 2 2 DATA_1N_BK(LVDS) DATA_1N_C(LVDS) 9 9 2 2 DATA_1N_C(LVDS)
GAIN_FIX_C 31 DATA_1P_BK(LVDS) 10 10 1 1 DATA_1P_BK(LVDS) DATA_1P_C(LVDS) 10 10 1 1 DATA_1P_C(LVDS)
SGND 30
DATA_2N_C(LVDS) 29
DATA_2P_C(LVDS) 28
SGND 27
INT_ST_M 26
PALA_STG_P0_M 25
PALA STG_P1_M
_ 24
PALA_STG_P2_M 23
GAIN_FIX_M 22 YC4 YC8
SGND 21 24V 1 1 5 5 +24V 24V 1 1 5 5 +24V
DATA_2N_M(LVDS) 20 PGND 2 2 4 4 GND PGND 2 2 4 4 GND
DATA_2P_M(LVDS) 19 REM Bk 3 3 3 3 START/STOP REM C 3 3 3 3 START/STOP
SGND 18 LOCK Bk 4 4 2 2 LOCKED PM-K LOCK C 4 4 2 2 LOCKED PM-C
DATA_3N_BK(LVDS) 17 CLK Bk 5 5 1 1 EXT.CLOCK CLK C 5 5 1 1 EXT.CLOCK
DATA_3P_BK(LVDS) 16
SGND 15
DATA_4N_BK(LVDS) 14
DATA_4P_BK(LVDS) 13
SGND 12
PARA_SIG_P3_2_BK 11
INT_ST_2_BK 10
INT_ST_1_BK 9
PARA_SIG_P0_BK 8
PARA_SIG_P1_BK 7
PARA_SIG_P2_BK 6
GAIN_FIX_BK 5
SGND 4 YC2
DATA_2N_BK(LVDS) 3 GND 1 1 4 4 GND YC2
DATA_2P_ BK(LVDS) 2 TH 2 2 3 3 TH GND 1 1 4 4 GND
SGND 1 PD 3 3 2 2 PD PDPWB-M TH 2 2 3 3 TH
PDPWB-Y
+5V 4 4 1 1 +5V PD 3 3 2 2 PD
+5V 4 4 1 1 +5V
YC12 YC2
SGND 60 60 1 1 SGND
BD_Y 59 59 2 2 BD_Y
LSU_TH_Y 58 58 3 3 LSU_TH_Y
CUALM_Y 57 57 4 4 CUALM_Y
EPWB
PARA_SIG_P3_Y 56 56 5 5 PARA_SIG_P3_Y
PARA_SIG_P4_Y 55 55 6 6 PARA_SIG_P4_Y APCPWB-M
SGND
SDCLK_Y
54
53
54
53
7
8
7
8
SGND
SDCLK_Y
APCPWB-Y
SGND 52 52 9 9 SGND
DATA_1N_Y(LVDS) 51 51 10 10 DATA_1N_Y(LVDS)
DATA_1P_Y(LVDS) 50 50 11 11 DATA_1P_Y(LVDS)
SGND 49 49 12 12 SGND
REM_Y 48 48 13 13 REM_Y YC5 YC1 YC9 YC1
LOCK_Y 47 47 14 14 LOCK_Y SGND 1 1 10 10 SGND SGND 1 1 10 10 SGND
CLK_Y 46 46 15 15 CLK_Y BD_M 2 2 9 9 BD_M BD_Y 2 2 9 9 BD_Y
SGND 45 45 16 16 SGND LSU_TH_M 3 3 8 8 LSU_TH_M LSU_TH_Y 3 3 8 8 LSU_TH_Y
BD_C 44 44 17 17 BD_C 5V 4 4 7 7 5V 5V 4 4 7 7 5V
LSU_TH_C 43 43 18 18 LSU_TH_C NC 5 5 6 6 NC NC 5 5 6 6 NC
CUALM_C 42 42 19 19 CUALM_C ENABLE_M 6 6 5 5 ENABLE_M ENABLE_Y 6 6 5 5 ENABLE_Y
PARA_SIG_P3_C 41 41 20 20 PARA_SIG_P3_C S/H_M 7 7 4 4 S/H_M S/H_Y 7 7 4 4 S/H_Y
PARA_SIG_P4_C 40 40 21 21 PARA_SIG_P4_C VCONT_M 8 8 3 3 VCONT_M VCONT_Y 8 8 3 3 VCONT_Y
SGND 39 39 22 22 SGND DATA_1N_M(LVDS) 9 9 2 2 DATA_1N_M(LVDS) DATA_1N_Y(LVDS) 9 9 2 2 DATA_1N_Y(LVDS)
SDCLK_C 38 38 23 23 SDCLK_C DATA_1P_M(LVDS) 10 10 1 1 DATA_1P_M(LVDS) DATA_1P_Y(LVDS) 10 10 1 1 DATA_1P_Y(LVDS)
SGND 37 37 24 24 SGND
DATA_1N_C(LVDS) 36 36 25 25 DATA_1N_C(LVDS)
DATA_1P_C(LVDS) 35 35 26 26 DATA_1P_C(LVDS)
SGND 34 34 27 27 SGND
REM_C 33 33 28 28 REM_C
LOCK_C 32 32 29 29 LOCK_C YC6 YC10
CLK_C 31 31 30 30 CLK_C 24V 1 1 5 5 +24V 24V 1 1 5 5 +24V
SGND 30 30 31 31 SGND PGND 2 2 4 4 GND PGND 2 2 4 4 GND
BD_M 29 29 32 32 BD_M REM M 3 3 3 3 START/STOP REM Y 3 3 3 3 START/STOP
LSU_TH_M 28 28 33 33 LSU_TH_M LOCK M 4 4 2 2 LOCKED PM-M LOCK Y 4 4 2 2 LOCKED PM-Y
CUALM_M 27 27 34 34 CUALM_M CLK M 5 5 1 1 EXT.CLOCK CLK Y 5 5 1 1 EXT.CLOCK
PARA_SIG_P3_M 26 26 35 35 PARA_SIG_P3_M
SGND 24 24 37 37 SGND
SDCLK_M 23 23 38 38 SDCLK_M
SGND 22 22 39 39 SGND
DATA_1N_M(LVDS) 21 21 40 40 DATA_1N_M(LVDS)
DATA_1P_M(LVDS) 20 20 41 41 DATA_1P_M(LVDS)
SGND 19 19 42 42 SGND LSURPWB
REM_M 18 18 43 43 REM_M
LOCK_M 17 17 44 44 LOCK_M
CLK_M 16 16 45 45 CLK_M
SGND 15 15 46 46 SGND
BD_BK 14 14 47 47 BD_BK
LSU_TH_BK 13 13 48 48 LSU_TH_BK YC1 YC7
CUALM_BK 12 12 49 49 CUALM_BK +24V1 1 1 1 1 +24V1
PARA_SIG_P3_BK 11 11 50 50 PARA_SIG_P3_BK +24V1 2 2 2 2 +24V1 PSPWB
PARA_SIG_P4_BK 10 10 51 51 PARA_SIG_P4_BK GND 3 3 3 3 GND
SGND 9 9 52 52 SGND GND 4 4 4 4 GND
SDCLK_BK 8 8 53 53 SDCLK_BK
SGND 7 7 54 54 SGND +5V1 5 5
DATA_1N_BK(LVDS) 6 6 55 55 DATA_1N_BK(LVDS) +5V1 6 6
DATA_1P_BK(LVDS) 5 5 56 56 DATA_1P_BK(LVDS) GND 7 7
SGND 4 4 57 57 SGND GND 8 8 YC15
REM_BK 3 3 58 58 REM_BK 6 6 +5V_AN
LOCK_BK 2 2 59 59 LOCK_BK 5 5 +5V_AN
CLK_BK 1 1 60 60 CLK_BK 4 4 GND
3 3 GND
2 2 +3.3V2
1 1 GND EPWB
YC21
1 2 2 2 DR_CW
LSUCM 2
Relay
1 1 1 DR_CCW
2-4-14
2LK/2LN/2LM/2LC
No.2 (35 ppm model/45 ppm model/55 ppm model)
YC11 YC2 YC5 YC1

SGND 64 64 1 1 SGND SGND 1 1 30 30 SGND YC3
CLK 63 63 2 2 CLK BD Bk 2 2 29 29 BD Bk GND 1 1 4 4 GND
SGND 62 62 3 3 SGND LSU_TH Bk 3 3 28 28 LSU_TH Bk TH 2 2 3 3 TH
SDI 61 61 4 4 SDI PALA_SIG P3_2Bk 4 4 27 27 PALA_SIG P3_2Bk BD 3 3 2 2 PD PDPWB-K YC10 YC1
SGND 60 60 5 5 SGND LDD_CS 2 Bk 5 5 26 26 LDD_CS 2 Bk +5V 4 4 1 1 +5V SGND 1 1 30 30 SGND
YC2
SDO 59 59 6 6 SDO 5V 6 6 25 25 5V BD C 2 2 29 29 BD C GND 1 1 4 4 GND
SGND 58 58 7 7 SGND 5V 7 7 24 24 5V LSU_TH C 3 3 28 28 LSU_TH C TH 2 2 3 3 TH
MSET_N 57 57 8 8 MSET_N 5V 8 8 23 23 5V - 4 4 27 27 - PD 3 3 2 2 PD PDPWB-C
SGND 56 56 9 9 SGND LDD_CS 1 Bk 9 9 22 22 LDD_CS 1 Bk - 5 5 26 26 - +5V 4 4 1 1 +5V
IDD_CS_Y 55 55 10 10 IDD_CS_Y SDI1 10 10 21 21 SDI1 5V 6 6 25 25 5V
EEPROM_CS_Y 54 54 11 11 EEPROM_CS_Y SDO1 11 11 20 20 SDO1 5V 7 7 24 24 5V
IDD_CS_C 53 53 12 12 IDD_CS_C CLK1 12 12 19 19 CLK1 5V 8 8 23 23 5V
EEPROM_CS_C 52 52 13 13 EEPROM_CS_C EEPROM CS 1 Bk 13 13 18 18 EEPROM CS 1 Bk LDD_CS 1 C 9 9 22 22 LDD_CS 1 C
IDD_CS_M 51 51 14 14 IDD_CS_M MSET_N 14 14 17 17 MSET_N SDI1 10 10 21 21 SDI1
EEPROM_CS_M 50 50 15 15 EEPROM_CS_M CUALM Bk 15 15 16 16 CUALM Bk SDO1 11 11 20 20 SDO1
IDD_CS_2_BK 49 49 16 16 IDD_CS_2_BK INT_ST 2 Bk 16 16 15 15 INT_ST 2 Bk CLK1 12 12 19 19 CLK1
EEPROM_CS_2_BK 48 48 17 17 EEPROM_CS_2_BK INT_ST 1 Bk 17 17 14 14 INT_ST 1 Bk EEPROM CS C 13 13 18 18 EEPROM CS C
IDD_CS_1_BK 47 47 18 18 IDD_CS_1_BK PALA_SIG P0 Bk 18 18 13 13 PALA_SIG P0 Bk MSET_N 14 14 17 17 MSET_N
EEPROM_CS_1_BK 46 46 19 19 EEPROM_CS_1_BK PALA_SIG P1 Bk 19 19 12 12 PALA_SIG P1 Bk APCPWB-K CUALM C 15 15 16 16 CUALM C APCPWB-C
SGND 45 45 20 20 SGND PALA_SIG P2 Bk 20 20 11 11 PALA_SIG P2 Bk - 16 16 15 15 -
INT_ST_Y 44 44 21 21 INT_ST 1 Y PALA_SIG P3 Bk 21 21 10 10 PALA_SIG P3 Bk INT_ST 1 C 17 17 14 14 INT_ST 1 C
PALA_STG_P0_Y 43 43 22 22 PALA_STG_P0_Y PALA_SIG P4 Bk 22 22 9 9 PALA_SIG P4 Bk PALA_SIG P0 C 18 18 13 13 PALA_SIG P0 C
PALA_STG_P1_Y 42 42 23 23 PALA_STG_P1_Y SDCLK Bk 23 23 8 8 SDCLK Bk PALA_SIG P1 C 19 19 12 12 PALA_SIG P1 C
PALA_STG P2_Y 41 41 24 24 PALA_STG P2_Y GAIN FIX Bk 24 24 7 7 GAIN FIX Bk PALA_SIG P2 C 20 20 11 11 PALA_SIG P2 C
GAIN_FIX_Y 40 40 25 25 GAIN_FIX_Y DATA_1N_Bk(LVDS) 25 25 6 6 DATA_1N_Bk(LVDS) PALA_SIG P3 C 21 21 10 10 PALA_SIG P3 C
SGND 39 39 26 26 SGND DATA_1P_Bk(LVDS) 26 26 5 5 DATA_1P_Bk(LVDS) PALA_SIG P4 C 22 22 9 9 PALA_SIG P4 C
DATA_2N_Y(LVDS) 38 38 27 27 DATA_2N_Y(LVDS) SGND 27 27 4 4 SGND SDCLK C 23 23 8 8 SDCLK C
DATA_2P_Y(LVDS) 37 37 28 28 DATA_2P_Y(LVDS) DATA_2N_Bk(LVDS) 28 28 3 3 DATA_2N_Bk(LVDS) GAIN FIX C 24 24 7 7 GAIN FIX C
SGND 36 36 29 29 SGND DATA_2P_Bk(LVDS) 29 29 2 2 DATA_2P_Bk(LVDS) DATA_1N_C(LVDS) 25 25 6 6 DATA_1N_C(LVDS)
INT_ST_ C 35 35 30 30 INT_ST 1 C SGND 30 30 1 1 SGND DATA_1P_C(LVDS) 26 26 5 5 DATA_1P_C(LVDS)
PALA_STG_P0_C 34 34 31 31 PALA_STG_P0_C SGND 27 27 4 4 SGND
PALA_STG_P1_C 33 33 32 32 PALA_STG_P1_C DATA_2N_C(LVDS) 28 28 3 3 DATA_2N_C(LVDS)
PALA_STG_P2_C 32 32 33 33 PALA_STG_P2_C YC6 DATA_2P_C(LVDS) 29 29 2 2 DATA_2P_C(LVDS)
GAIN_FIX_C 31 31 34 34 GAIN_FIX_C SDI_2 1 SGND 30 30 1 1 SGND
SGND 30 30 35 35 SGND SDO_2 2
DATA_2N_C(LVDS) 29 29 36 36 DATA_2N_C(LVDS) CLK_2 3
DATA_2P_C(LVDS) 28 28 37 37 DATA_2P_C(LVDS) _
EEPROM CS 2 Bk 4
SGND 27 27 38 38 SGND SGND 5
INT_ST_M 26 26 39 39 INT_ST 1 M DATA_3N_Bk(LVDS) 6
PALA_STG_P0_M 25 25 40 40 PALA_STG_P0_M DATA_3P_Bk(LVDS) 7
PALA STG_P1_M
_ 24 24 41 41 PALA STG_P1_M
_ SGND 8
PALA_STG_P2_M 23 23 42 42 PALA_STG_P2_M DATA_4N_Bk(LVDS) 9
GAIN_FIX_M 22 22 43 43 GAIN_FIX_M DATA_4P_Bk(LVDS) 10 YC9
SGND 21 21 44 44 SGND 24V 1 1 5 5 +24V
DATA_2N_M(LVDS) 20 20 45 45 DATA_2N_M(LVDS) PGND 2 2 4 4 GND
DATA_2P_M(LVDS) 19 19 46 46 DATA_2P_M(LVDS) YC4 REM C 3 3 3 3 START/STOP
SGND 18 18 47 47 SGND 24V 1 1 5 5 +24V LOCK C 4 4 2 2 LOCKED PM-C
DATA_3N_BK(LVDS) 17 17 48 48 DATA_3N_BK(LVDS) PGND 2 2 4 4 GND CLK C 5 5 1 1 EXT.CLOCK
DATA_3P_BK(LVDS) 16 16 49 49 DATA_3P_BK(LVDS) REM Bk 3 3 3 3 START/STOP
SGND 15 15 50 50 SGND LOCK Bk 4 4 2 2 LOCKED PM-K
DATA_4N_BK(LVDS) 14 14 51 51 DATA_4N_BK(LVDS) CLK Bk 5 5 1 1 EXT.CLOCK
DATA_4P_BK(LVDS) 13 13 52 52 DATA_4P_BK(LVDS)
SGND 12 12 53 53 SGND
PARA_SIG_P3_2_BK 11 11 54 54 PARA_SIG_P3_2 BK
INT_ST_2_BK 10 10 55 55 INT_ST 2 BK
INT_ST_1_BK 9 9 56 56 INT_ST 1 BK
PARA_SIG_P0_BK 8 8 57 57 PARA_SIG_P0_BK
GAIN_FIX_BK 5 5 60 60 GAIN_FIX_BK YC8 YC1
SGND 4 4 61 61 SGND SGND 1 1 30 30 SGND YC2 YC12 YC1
DATA_2N_BK(LVDS) 3 3 62 62 DATA_2N_BK(LVDS) BD M 2 2 29 29 BD M GND 1 1 4 4 GND SGND 1 1 30 30 SGND YC2
DATA_2P_ BK(LVDS) 2 2 63 63 DATA_2P_ BK(LVDS) LSU_TH M 3 3 28 28 LSU_TH M TH 2 2 3 3 TH BD Y 2 2 29 29 BD Y GND 1 1 4 4 GND
SGND 1 1 64 64 SGND - 4 4 27 27 - PD 3 3 2 2 PD PDPWB-M LSU_TH Y 3 3 28 28 LSU_TH Y TH 2 2 3 3 TH
PDPWB-Y
- 5 5 26 26 - +5V 4 4 1 1 +5V - 4 4 27 27 - PD 3 3 2 2 PD
5V 6 6 25 25 5V - 5 5 26 26 - +5V 4 4 1 1 +5V
YC12 YC3 5V 7 7 24 24 5V 5V 6 6 25 25 5V
SGND 60 60 1 1 SGND 5V 8 8 23 23 5V 5V 7 7 24 24 5V
BD_Y 59 59 2 2 BD_Y LDD_CS 1 M 9 9 22 22 LDD_CS 1 M 5V 8 8 23 23 5V
LSU_TH_Y 58 58 3 3 LSU_TH_Y SDI1 10 10 21 21 SDI1 LDD_CS 1 Y 9 9 22 22 LDD_CS 1 Y
CUALM_Y 57 57 4 4 CUALM_Y SDO1 11 11 20 20 SDO1 SDI1 10 10 21 21 SDI1
EPWB
PARA_SIG_P3_Y 56 56 5 5 PARA_SIG_P3_Y CLK1 12 12 19 19 CLK1 SDO1 11 11 20 20 SDO1

PARA_SIG_P4_Y 55 55 6 6 PARA_SIG_P4_Y EEPROM CS M 13 13 18 18 EEPROM CS M CLK1 12 12 19 19 CLK1
SGND 54 54 7 7 SGND MSET_N 14 14 17 17 MSET_N EEPROM CS Y 13 13 18 18 EEPROM CS Y
SDCLK_Y 53 53 8 8 SDCLK_Y CUALM M 15 15 16 16 CUALM M MSET_N 14 14 17 17 MSET_N
SGND 52 52 9 9 SGND - 16 16 15 15 - CUALM Y 15 15 16 16 CUALM Y
DATA_1N_Y(LVDS) 51 51 10 10 DATA_1N_Y(LVDS) INT_ST 1 M 17 17 14 14 INT_ST 1 M APCPWB-M - 16 16 15 15 -
DATA_1P_Y(LVDS) 50 50 11 11 DATA_1P_Y(LVDS) PALA_SIG P0 M 18 18 13 13 PALA_SIG P0 M INT_ST 1 Y 17 17 14 14 INT_ST 1 Y
SGND 49 49 12 12 SGND _
PALA SIG P1 M 19 19 12 12 _
PALA SIG P1 M PALA_SIG P0 Y 18 18 13 13 PALA_SIG P0 Y APCPWB-Y
REM_Y 48 48 13 13 REM_Y PALA_SIG P2 M 20 20 11 11 PALA_SIG P2 M PALA_SIG P1 Y 19 19 12 12 PALA_SIG P1 Y
LOCK_Y 47 47 14 14 LOCK_Y PALA_SIG P3 M 21 21 10 10 PALA_SIG P3 M PALA_SIG P2 Y 20 20 11 11 PALA_SIG P2 Y
CLK_Y 46 46 15 15 CLK_Y PALA_SIG P4 M 22 22 9 9 PALA_SIG P4 M PALA_SIG P3 Y 21 21 10 10 PALA_SIG P3 Y
SGND 45 45 16 16 SGND SDCLK M 23 23 8 8 SDCLK M PALA_SIG P4 Y 22 22 9 9 PALA_SIG P4 Y
BD_C 44 44 17 17 BD_C GAIN FIX M 24 24 7 7 GAIN FIX M SDCLK Y 23 23 8 8 SDCLK Y
LSU_TH_C 43 43 18 18 LSU_TH_C DATA_1N_M(LVDS) 25 25 6 6 DATA_1N_M(LVDS) GAIN FIX Y 24 24 7 7 GAIN FIX Y
CUALM_C 42 42 19 19 CUALM_C DATA_1P_M(LVDS) 26 26 5 5 DATA_1P_M(LVDS) DATA_1N_Y(LVDS) 25 25 6 6 DATA_1N_Y(LVDS)
PARA_SIG_P3_C 41 41 20 20 PARA_SIG_P3_C SGND 27 27 4 4 SGND DATA_1P_Y(LVDS) 26 26 5 5 DATA_1P_Y(LVDS)
PARA_SIG_P4_C 40 40 21 21 PARA_SIG_P4_C DATA_2N_M(LVDS) 28 28 3 3 DATA_2N_M(LVDS) SGND 27 27 4 4 SGND
SGND 39 39 22 22 SGND DATA_2P_M(LVDS) 29 29 2 2 DATA_2P_M(LVDS) DATA_2N_Y(LVDS) 28 28 3 3 DATA_2N_Y(LVDS)
SDCLK_C 38 38 23 23 SDCLK_C SGND 30 30 1 1 SGND DATA_2P_Y(LVDS) 29 29 2 2 DATA_2P_Y(LVDS)
SGND 37 37 24 24 SGND SGND 30 30 1 1 SGND
DATA_1N_C(LVDS) 36 36 25 25 DATA_1N_C(LVDS)
DATA_1P_C(LVDS) 35 35 26 26 DATA_1P_C(LVDS)
SGND 34 34 27 27 SGND
REM_C 33 33 28 28 REM_C
LOCK_C 32 32 29 29 LOCK_C YC7 YC11
CLK_C 31 31 30 30 CLK_C 24V 1 1 5 5 +24V 24V 1 1 5 5 +24V
SGND 30 30 31 31 SGND PGND 2 2 4 4 GND PGND 2 2 4 4 GND
BD_M 29 29 32 32 BD_M REM M 3 3 3 3 START/STOP REM Y 3 3 3 3 START/STOP
LSU_TH_M 28 28 33 33 LSU_TH_M LOCK M 4 4 2 2 LOCKED PM-M LOCK Y 4 4 2 2 LOCKED PM-Y
CUALM_M 27 27 34 34 CUALM_M CLK M 5 5 1 1 EXT.CLOCK CLK Y 5 5 1 1 EXT.CLOCK
SGND 24 24 37 37 SGND
SDCLK_M 23 23 38 38 SDCLK_M
SGND 22 22 39 39 SGND
DATA_1N_M(LVDS) 21 21 40 40 DATA_1N_M(LVDS)
DATA_1P_M(LVDS) 20 20 41 41 DATA_1P_M(LVDS)
SGND 19 19 42 42 SGND LSURPWB
REM_M 18 18 43 43 REM_M
LOCK_M 17 17 44 44 LOCK_M
CLK_M 16 16 45 45 CLK_M
SGND 15 15 46 46 SGND
BD_BK 14 14 47 47 BD_BK
LSU_TH_BK 13 13 48 48 LSU_TH_BK YC1 YC10
CUALM_BK 12 12 49 49 CUALM_BK +24V1 1 1 1 1 +24V1
PARA_SIG_P3_BK 11 11 50 50 PARA_SIG_P3_BK +24V1 2 2 2 2 +24V1 PSPWB
PARA_SIG_P4_BK 10 10 51 51 PARA_SIG_P4_BK GND 3 3 3 3 GND
SDCLK_BK 8 8 53 53 SDCLK_BK
SGND 7 7 54 54 SGND +5V1 5 5
DATA_1N_BK(LVDS) 6 6 55 55 DATA_1N_BK(LVDS) +5V1 6 6
DATA_1P_BK(LVDS) 5 5 56 56 DATA_1P_BK(LVDS) GND 7 7
SGND 4 4 57 57 SGND GND 8 8 YC15
REM_BK 3 3 58 58 REM_BK +3.3V2 9 9 6 6 +5V_AN
LOCK_BK 2 2 59 59 LOCK_BK GND 10 10 5 5 +5V_AN
CLK_BK 1 1 60 60 CLK_BK 4 4 GND
3 3 GND
2 2 +3.3V2
1 1 GND EPWB
YC21
1 2 2 DR_CW
LSUCM 2 1 1 DR_CCW
2-4-15
2LK/2LN/2LM/2LC
YC16
+3.3V 1 4 1 1 3.3V1 YC9 YC1 Developer unit K
SDA 2 3 2 2 I2C_SDA TPD_TEMP_BK 1 1 1 1 TPD_TEMP
OTEMS1 GND 3 2 3 3 GND DLP_VCONT_BK_1 2 2 2 2 DLP_VCONT
SCL 4 1 4 4 I2C_SCL TPD_BK_1 3 3 3 3 TPD_1
TN_CLK_BK 4 4 4 4 TN_CLK
2 2 5 5 FRONT_OPEN GND 5 5 5 5 GND TS-K
FRCSW 1 1 6 6 GND DLP_ADR1_BK 6 6 6 6 DLP_ADR1
DLP_ADR0_BK 7 7 7 7 DLP_ADR0
+ 1 2 1 4 7 7 24V FRPWB EEP_SDA1 8 8 8 8 EEP_SDA1
LSUFM - 2
Relay
1 2 3 8 8 LSU_FAN_OUT EEP_SCL1 9 9 9 9 EEP_SCL1
3.3V2 10 10 10 10 3.3V2
Relay
1 2 3 2 9 9 CL_MOT
WTM 2 Relay
1 4 1 10 10 24V 3V 11 11 1 1
11 11 GND 3.3V2 12 12 2 2 VM-K
WTNR_SET
5V YC7
WTNR_FULL 3.3V2 1 1 6 6 +3.3V Drum unit K
WTNR_LED EEP_SCL1 2 2 5 5 EEP SCL
_
5V LED EEP_SDA1 3 3 4 4 EEP SDA
GND 4 4 3 3 GND DRPWB-K
5V DRM_ADR0_Bk 5 5 2 2 A0
WTNR_NEAR DRM_ADR1_Bk 6 6 1 1 A1
WTNR_LED
5V_LED
24V 7 7 2 2 DRM1 ERASER (+)

Developer unit Y YC1 YC15 ERS_Bk_REM 8 8 1 1 ERS1 DR (-) CL-K
TPD_TEMP 1 1 1 1 TPD_TEMP_Y
DLP_VCONT 2 2 2 2 DLP_VCONT_Y_1
TPD_1 3 3 3 3 TPD_Y_1
TN_CLK 4 4 4 4 TN_CLK_Y 5V
TS-Y GND 5 5 5 5 GND DRM_INDEX_Bk
DLP_ADR1 6 6 6 6 DLP_ADR1_Y GND
DLP_ADR0 7 7 7 7 DLP_ADR0_Y
EEP_SDA1 8 8 8 8 EEP_SDA1
EEP_SCL1 9 9 9 9 EEP_SCL1
3.3V2 10 10 10 10 3.3V2 YC8
5V_LED 10 10
WTNR_LED 9 9
1 1 11 11 3V WTNR_NEAR 8 8
VM-Y 2 2 12 12 VIB_MOT YC2 YC1
+3.3V1 10 10 1 1 +3.3V1 5V 7 7 1 12 1 3 1 1 5V
+3.3V2 9 9 2 2 +3.3V2 WTNR_SET 6 6 2 11 2 Relay 2 2 2 Vout WTS2
YC14 +5V 8 8 3 3 +5V GND 5 5 3 10 3 1 3 3 GND
+3.3V 6 6 1 1 3.3V2 +24V 7 7 4 4 +24V
Drum unit Y EEP SCL 5 5 2 2 EEP_SCL1 +24V 6 6 5 5 +24V 5V_LED 4 4 4 9 1 4 A
LED
EEP SDA 4 4 3 3 EEP_SDA1 GND 5 5 6 6 GND WTNR_LED 3 3 5 8 2 3 K
DRPWB-Y GND 3 3 4 4 GND GND 4 4 7 7 GND WTNR_FULL 2 2 6 7 3
Relay
2 E WTS1
A0 2 2 5 5 DRM_ADR0_Y GND 3 3 8 8 GND 5V 1 1 7 6 4 1 C TR
A1 1 1 6 6 DRM_ADR1_Y GND 2 2 9 9 GND
GND 1 1 10 10 GND Relay
EPWB YC6
DRM1 ERASER (+) 2 2 7 7 24V YC7 YC3 DLP_FAN_M 4 4 8 5 1 2 +
CL-Y ERS1 DR (-) 1 1 8 8 ERS_Y_REM GND 1 1 1 1 GND 24V 3 3 9 4 2
Relay
1 - DEVFM2
WTNR_SET 2 2 2 2 WTNR_SET
INTER_LOCK 3 3 3 3 INTER_LOCK DLP_FAN_Bk 2 2 10 3 1 2 +
5V IH_CORE_SENS 4 4 4 4 IH_CORE_SENS 24V 1 1 11 2 2
Relay
1 - DEVFM1
DRM_INDEX_Y IH_CORE_MOT_REM 5 5 5 5 IH_CORE_MOT_REM 12 1
GND IH_CORE_CLK 6 6 6 6 IH_CORE_CLK
WTNR_LED 7 7 7 7 WTNR_LED
IH_COIL_FAN_ALM 8 8 8 8 IH_COIL_FAN_ALM
YC10 IH_COIL_FAN_H 9 9 9 9 IH_COIL_FAN_H 3.3V1 1 1 4 1 4 1 +3.3V
Developer unit C YC1 YC13 YC2 IH_COIL_FAN_L 10 10 10 10 IH_COIL_FAN_L I2C_SDA 2 2 3 2 3 2 SDA
TPD_TEMP 1 1 1 1 TPD_TEMP_C GND 1 1 1 1 GND EXIT_FAN 11 11 11 11 EXIT_FAN GND 3 3 2
Relay
3 2 3 GND OTEMS2
DLP_VCONT 2 2 2 2 DLP_VCONT_C_1 DRM_INDEX_Bk 2 2 2 2 DRM_INDEX_Bk CONTAIN_FAN 12 12 12 12 CONTAIN_FAN I2C_SCL 4 4 1 4 1 4 SCL
TPD_1 3 3 3 3 TPD_C_1 ERS_Bk_REM 3 3 3 3 ERS_Bk JUNC_SOL_REM 13 13 13 13 JUNC_SOL_REM
TN_CLK 4 4 4 4 TN_CLK_C TPD_Bk_1 4 4 4 4 TPD_Bk_1 JUNC_SOL_RET 14 14 14 14 JUNC_SOL_RET
TS-C GND 5 5 5 5 GND DLP_VCONT_Bk_1 5 5 5 5 DLP_VCONT_Bk_1 GND 15 15 15 15 GND
DLP_ADR1 6 6 6 6 DLP_ADR1_C TPD_TEMP_Bk 6 6 6 6 TPD_TEMP_Bk EXIT_PAPE_SENS 16 16 16 16 EXIT_PAPE_SENS
DLP_ADR0 7 7 7 7 DLP_ADR0_C GND 7 7 7 7 GND EXIT_FEED_SENS 17 17 17 17 EXIT_FEED_SENS
EEP_SDA1 8 8 8 8 EEP_SDA1 DRM_INDEX_M 8 8 8 8 DRM_INDEX_M ROT_MOT_REM 18 18 18 18 ROT_MOT_REM YC4
EEP_SCL1 9 9 9 9 EEP_SCL1 ERS_M_REM 9 9 9 9 ERS_M ROT_MOT_PH 19 19 19 19 ROT_MOT_PH 5V 1 1
3.3V2 10 10 10 10 3.3V2 TPD_M_1 10 10 10 10 TPD_M_1 ROT_MOT_CLK 20 20 20 20 ROT_MOT_CLK LED1 2 2
DLP_VCONT_M_1 11 11 11 11 DLP_VCONT_M_1 ROT_MOT_PD 21 21 21 21 ROT_MOT_PD
TPD_TEMP_M 12 12 12 12 TPD_TEMP_M ROT_MOT_DIR 22 22 22 22 ROT_MOT_DIR
1 1 11 11 3V GND 13 13 13 13 GND GND 23 23 23 23 GND
VM-C 2 2 12 12 VIB_MOT DRM_INDEX_C 14 14 14 14 DRM_INDEX_C DLP_FAN_Bk_H 24 24 24 24 DLP_FAN_Bk_H 5V 3 3
ERS_C_REM 15 15 15 15 ERS_C DLP_FAN_Bk_L 25 25 25 25 DLP_FAN_Bk_L LED2 4 4
TPD_C_1 16 16 16 16 TPD_C_1 DLP_FAN_CLR_H 26 26 26 26 DLP_FAN_CLR_H
YC12 DLP_VCONT_C_1 17 17 17 17 DLP_VCONT_C_1 DLP_FAN_CLR_L 27 27 27 27 DLP_FAN_CLR_L
+3.3V 6 6 1 1 3.3V2 TPD_TEMP_C 18 18 18 18 TPD_TEMP_C WTNR_SET 28 28 28 28 WTNR_FULL IH_COIL_FAN_ALM 5 5 3 1 S
Drum unit C EEP SCL 5 5 2 2 EEP_SCL1 GND 19 19 19 19 GND WTNR_NEAR 29 29 29 29 WTNR_NEAR IH_COIL_FAN 6 6 2 Relay 2 + CFM1
EEP SDA 4 4 3 3 EEP_SDA1 TN_CLK 20 20 20 20 TN_CLK WTNR_VCONT 30 30 30 30 WTNR_VCONT 24V 7 7 1 3 -
DRPWB-C GND 3 3 4 4 GND GND 21 21 21 21 GND GND 31 31 31 31 GND
A0 2 2 5 5 DRM_ADR0_C EEP_SCL1 22 22 22 22 EEP_SCL1 ROT_MOT_REM 32 32 32 32 ROT_MOT_REM 24V 8 8 2 1 +
A1 1 1 6 6 DRM_ADR1_C GND 23 23 23 23 GND ROT_MOT_CLK 33 33 33 33 ROT_MOT_CLK EXIT FAN 9 9 1
Relay
2 - EFFM
EEP_SDA1 24 24 24 24 EEP_SDA1 ROT_MOT_PD 34 34 34 34 ROT_MOT_PD
GND 25 25 25 25 GND ROT_MOT_DIR 35 35 35 35 ROT_MOT_DIR
TPD_Y_1 26 26 26 26 TPD_Y_1 ROT_HP_SENS 36 36 36 36 ROT_HP_SENS YC17
DRM1 ERASER (+) 2 2 7 7 24V DLP_VCONT_Y_1 27 27 27 27 DLP_VCONT_Y_1 THOP_MOT_Bk_REM 37 37 37 37 THOP_MOT_Bk_REM GND 1
CL-C ERS1 DR (-) 1 1 8 8 ERS_C_REM TPD_TEMP_Y 28 28 28 28 TPD_TEMP_Y THOP_MOT_M_REM 38 38 38 38 THOP_MOT_M_REM IH_CORE_SENS 2
ERS_Y_REM 29 29 29 29 ERS_Y THOP_MOT_C_REM 39 39 39 39 THOP_MOT_C_REM 5V 3
DRM_INDEX_Y 30 30 30 30 DRM_INDEX_Y THOP_MOT_Y_REM 40 40 40 40 THOP_MOT_Y_REM
5V FRONT_OPEN 31 31 31 31 FRONT_OPEN GND 41 41 41 41 GND
DRM_INDEX_C GND 32 32 32 32 GND ENCODE_Bk 42 42 42 42 ENCODE_Bk IH_CORE B/ 4
GND I2C_SCL 33 33 33 33 I2C_SCL ENCODE_M 43 43 43 43 ENCODE_M IH_CORE B 5
GND 34 34 34 34 GND ENCODE_C 44 44 44 44 ENCODE_C IH_CORE A 6
I2C_SDA 35 35 35 35 I2C_SDA ENCODE_Y 45 45 45 45 ENCODE_Y IH_CORE A/ 7
YC1 YC11 GND 36 36 36 36 GND THOP_Bk 46 46 46 46 THOP_Bk
Developer unit M LSU_FAN_REM 37 37 37 37 LSU_FAN_REM THOP_M 47 47 47 47 THOP_M 24V 8
TPD_TEMP 1 1 1 1 TPD_TEMP_M
DLP_VCONT_M_1 CLEAN_MOT_LOCK 38 38 38 38 CLEAN_MOT_LOCK THOP_ C 48 48 48 48 THOP_ C EXIT PAPER(SUB) 9
DLP_VCONT 2 2 2 2
TPD_M_1 CLEAN_MOT_REM 39 39 39 39 CLEAN_MOT_REM THOP_Y 49 49 49 49 THOP_Y
TPD_1 3 3 3 3
TN_CLK_M GND 40 40 40 40 GND GND 50 50 50 50 GND
TN_CLK 4 4 4 4
GND 5 5 5 5 GND YC5
TS-M DLP_ADR1 6 6 6 6 DLP_ADR1_M
ROT_CORE A 1 1
DLP_ADR0 7 7 7 7 DLP_ADR0_M
EEP_SDA1 ROT_CORE B 2 2
EEP_SDA1 8 8 8 8
EEP_SCL1 ROT_CORE A/ 3 3
EEP_SCL1 9 9 9 9
10 10 10 10 3.3V2 ROT_CORE B/ 4 4
3.3V2
GND 5 5
1 1 11 11 3V ROT_HP_SENS 6 6
VM-M 2 2 12 12 VIB_MOT 5V 7 7 Eject unit
SB_CORE B/ 8 8 13 1 4 4 B/
SB_CORE A/ 9 9 12 2 3 3 A/
YC10 SB_CORE B 10 10 11 3 2 2 B EM
Drum unit M +3.3V 6 6 1 1 3.3V2 SB_CORE A 11 11 10 4 1 1 A
EEP SCL 5 5 2 2 EEP_SCL1
EEP SDA 4 4 3 3 EEP_SDA1 GND 12 12 9 5 3 3 GND
DRPWB-M GND 3 3 4 4 GND EXIT_FEED_SENS 13 13 8 6 2 2 Vout SBS
A0 2 2 5 5 DRM_ADR0_M 5V 14 14 7 7 1 1 5V
A1 1 1 6 6 DRM_ADR1_M Relay
GND 15 15 6 8 3 3 GND
EXIT_PAPER_SENS 16 16 5 9 2 2 Vout EFS
5V 17 17 4 10 1 1 5V
DRM1 ERASER (+) 2 2 7 7 24V
CL-M ERS1 DR (-) 1 1 8 8 ERS_M_REM +24V1 18 18 3 11 3 1 COM
JUNC_SOL_KYU 19 19 2 12 2 Relay 2 ACT FSSOL
JUNC_SOL_FUK 20 20 1 13 1 3 KEEP
5V
DRM_INDEX_M
GND
2-4-16
2LK/2LN/2LM/2LC
YC26
+5V A20 A20 A1 A1 1 14 1 1 5V
FSR_BLT_PLS A19 A19 A2 A2 2 13 2 2 Vout FUBLS Fuser unit
GND A18 A18 A3 A3 3 12 3 3 GND
+5V A17 A17 A4 A4 4 11 1 1 5V

FSR_RLS_SENS A16 A16 A5 A5 5 10 2 2 Vout FURS
GND A15 A15 A6 A6 6 9 3 3 GND
+5V A14 A14 A7 A7 7 8 1 1 5V

FSR_SIZE_SENS A13 A13 A8 A8 8 Relay 7 2 2 Vout FUES
GND A12 A12 A9 A9 9 6 3 3 GND
FSR_RLS_DR_CW A11 A11 A10 A10 10 5 1 2

FSR_RLS_DR_CCW A10 A10 A11 A11 11 4 2 Relay
1 FURM
+24V1 A9 A9
FSR_FAN A8 A8 12 3 1 3 +
FSR_FAN_ALM A7 A7 13 2 2 Relay 2 - FURFM
14 1 3 1 S
+24V1 A6 A6 A12 A12
EDGE_FAN A5 A5 A13 A13
EDGE_FAN_ALM A4 A4 B13 B13
+24V1 A3 A3 B10 B10 1 1 1 3 +

EDGE_FAN YC1 YC2
A2 A2 B11 B11 2 2 2 2 - FUFFM
Connector holder
EDGE_FAN_ALM A1 A1 B12 B12 3 3 3 1 S
BRIDGE_FAN B20 B20 1 2 - 1 3 GND

+24V1 B19 B19 2
Relay
1 + BRFM YC3 2 2 FSR_NCTH1 FTH1
3 1 FSR_NCTH2
GND
MAIN_TH1
B18
B17
B18
B17
B1
B2
B1
B2
4
5
4
5
FUPWB
1 2
MAIN_TH2 B16 B16 B3 B3 6 6 YC4 2 1 FTH2
GUIDE_TH2 B15 B15 B4 B4 7 7 1 2
GND B14 B14 B5 B5 8 8 YC5 2 1 FTH3
GUIDE_TH1 B13 B13 B6 B6 9 9
GND B12 B12 B7 B7 10 10
EDGE_TH B11 B11 B8 B8 1 2

GND B10 B10 B9 B9 2
Relay
1 FTH4
PRESS_TH B9 B9
GND B8 B8
YC4 1 3 +
GND
+3.3V2
B7
B6
B7
B6
1
2
1
2
SGND
Vcc
2
3
Relay 2
1
-
S
CFM2
IH_HEAT_REM B5 B5 3 3 IH_REM
ROTATION B4 B4 4 4 ROTATION
IH_TXD B3 B3 5 5 RXD FIH
IH_RXD B2 B2 6 6 TXD
PRESS_HEART_REM B1 B1 YC9
COIL_LIVE 1
YC10
COIL_COM 1
EPWB FTS
FIHPWB YC6
+15V1 1 1 1 1
+15V2 2 2 2 2
3 3
4 4
YC8
3 3 GND
2 2 FSR_RELAY YC1
1 1 +24V IH_NEUTRAL 1 1 1
From PSPWB
IH_LIVE 2 2 2
FPWB1
YC27
MAIN_HEAT_REM 1 1
SUB_HEAT_REM 2 2
+24V2 3 3
ZEROC 4 4
GND 5 5
GND 6 6
FSR_RELAY 7 7
+24V1 8 8
PRESS_REM 9 9
YC11
+24V1 1 3 1 3 +
IH_PWB_FAN 2 2 2 Relay 2 - IHFM
IH_PWB_FAN_ALM 3 1 3 1 S
YC19
EXIT_REAR_FAN 1 2 1 2 -
+24V1 2 1 2
Relay
1 + ERFM
2-4-17
2LK/2LN/2LM/2LC
No.5 (30 ppm model/35 ppm model)
YC6 YC1
GND 1 1 64 64 GND
JOB_SET 2 2 63 63 JOB_SET Fuser drive unit
JOB_MOT_REM 3 3 62 62 JOB_MOT_REM
YC10
JOB MOT_CLK
_ 4 4 61 61 JOB MOT_CLK
_ GND 1 1
JOB_MOT_DIR 5 5 60 60 JOB_MOT_DIR M_TEMP 2 2
JOB_OPEN_SENS 6 6 59 59 JOB_OPEN_SENS
JOB_SOL_REM 7 7 58 58 JOB_SOL_REM YC18
GND 8 8 57 57 GND FSR_MOT_BRK 1 1 3.3V 3 3 1 1 +3.3V ID sensor
MAIN_HEAT_REM 9 9 56 56 MAIN_HEAT_REM FSR_MOT_DIR 2 2 6 6 CW/CCW REG_F_LED 4 4 2 2 LED_REF
SUB_HEAT_REM 10 10 55 55 SUB_HEAT_REM FSR_MOT_RDY 3 3 5 5 LD GND 5 5 3 3 GND IDS1
ZEROC 11 11 54 54 ZEROC FSR_MOT_CLK 4 4 4 4 CLOCK REG SENS_F_P
_ 6 6 4 4 VO_P
FSR_RELAY 12 12 53 53 FSR_RELAY FSR_MOT_REM 5 5 3 3 START/STOP FUM REG_SENS_F_S 7 7 5 5 VO_S
PRESS_REM 13 13 52 52 PRESS_REM GND 6 6 2 2 GND
EXIT REAR_FAN_L
_ 14 14 51 51 EXIT REAR_FAN_L
_ 24V2 7 7 1 1 +24V
EXIT_REAR_FAN_H 15 15 50 50 EXIT_REAR_FAN_H 3.3V 8 8 1 1 +3.3V
GND 16 16 49 49 GND REG_R_LED 9 9 2 2 LED_REF
FSR_CL_REM 17 17 48 48 FSR_CL_REM GND 10 10 3 3 GND IDS2
FSR_MOT_REM 18 18 47 47 FSR_MOT_REM REG_SENS_R_P 11 11 4 4 VO_P
FSR_MOT_CLK 19 19 46 46 FSR_MOT_CLK REG_SENS_R_S 12 12 5 5 VO_S
FSR_MOT_RDY 20 20 45 45 FSR_MOT_RDY CN1 CN2
FSR_MOT_DIR 21 21 44 44 FSR_MOT_DIR 11 11 SIG2 +5V 1
FSR_MOT_BRK 22 22 43 43 FSR_MOT_BRK 10 10 SIG1 S.GND 2 24V 13 13 3 1 COM
GND 23 23 42 42 GND
YC13 9 9 SGND SIG_1 3 CLN_SOL_REM 14 14 2 Relay 2 ACT CLSOL
MPF_TABLE 24 24 41 41 MPF_TABLE 8 8 +5V +5V 4 CLN_SOL_RET 15 15 1 3 RET
MPF_WID1 25 25 40 40 MPF_WID1 TRANS_MOT_BRK 1 1 7 7 BRAKE S.GND 5
MPF_WID2 26 26 39 39 MPF_WID2 TRANS_MOT_DIR 2 2 6 6 CW/CCW SIG_2 6
MPF_WID3 27 27 38 38 MPF_WID3 TRANS_MOT_RDY 3 3 5 5 FG
MPF_LNG 28 28 37 37 MPF_LNG TRANS_MOT_CLK 4 4 4 4 VM
GND 29 29 36 36 GND TRANS_MOT_REM 5 5 3 3 START/STOP
MPF_PPR_SET 30 30 35 35 MPF_PPR_SET GND 6 6 2 2 PGND
MPF_LIFT_UP 31 31 34 34 MPF_LIFT_UP 24V2 7 7 1 1 +24V1
TRM
MPF_LIFT_DOWN 32 32 33 33 MPF_LIFT_DOWN GND 8 8 Job separator
MPF_JAM 33 33 32 32 MPF_JAM 24V2 9 9
MPF_CL 34 34 31 31 MPF_CL TANK_SET 10 10 JMPWB
MPF_LIF2 35 35 30 30 MPF_LIF2
MPF_LIFT1 36 36 29 29 MPF_LIFT1
GND 37 37 28 28 GND YC8
TC_MOT_LOCK 38 38 27 27 TC_MOT_LOCK DLP_MOT_BK_DIR 1 YC2
TC_TONER_LED 39 39 26 26 TC_TONER_LED DLP_MOT_BK_RDY 2 GND 1 1 3 3 GND
TC TONER_FULL
_ 40 40 25 25 TC TONER_FULL
_ DLP_MOT_BK_CLK 3 YC20 YC1 JOB_OPEN_SENS 2 2 2 2 Vout JOCS
TC_TONER_VCONT 41 41 24 24 TC_TONER_VCONT DLP_MOT_BK_REM 4 JOB_SET 1 1 10 1 10 10 JOB_SET +5V1 3 3 1 1 5V
INTER_LOCK 42 42 23 23 INTER_LOCK GND 5 GND 2 2 9 2 9 9 GND
DU2_PD 43 43 22 22 DU2_PD +24V1 6 GND 3 3 8 3 8 8 GND JOB_B/ 4 4 4 B/
DU2_CLK 44 44 21 21 DU2_CLK JOB_MOT_REM 4 4 7 4 7 7 JOB_MOT_REM JOB_A/ 5 5 3 3 A/
DU2_REM_(CL_LOW) 45 45 20 20 DU2_REM_(CL_LOW) 24V1 5 5 6
Relay
5 6 6 24V1 JOB_B 6 6 2 2 B JEM
GND 46 46 19 19 GND JOB_MOT_CLK 6 6 5 6 5 5 JOB_MOT_CLK JOB_A 7 7 1 1 A
DU_OPEN 47 47 18 18 DU_OPEN 5V 7 7 4 7 4 4 5V
DU_FAN 48 48 17 17 DU_FAN JOB_MOT_DIR 8 8 3 8 3 3 JOB_MOT_DIR
PRESS_MOT_REM1 49 49 16 16 PRESS_MOT_REM1 JOB_OPEN_SENS 9 9 2 9 2 2 JOB_OPEN_SENS +24V1 8 8 2 1 COM
PRESS_MOT_REM2 50 50 15 15 PRESS_MOT_REM2 YC6 JOB SOL_REM
_ 10 10 1 10 1 1 JOB_SOL_REM JOB_SOL_OUT 9 9 1 2 ACT JFSSOL
PRESS_RLS_SENS 51 51 14 14 PRESS_RLS_SENS DLP_MOT_CLR_DIR 1 NC 11 11
DU_SENS 52 52 13 13 DU_SENS DLP_MOT_CLR_RDY 2
BELT_JAM_SENS 53 53 12 12 BELT_JAM_SENS DLP_MOT_CLR_CLK 3
GND 54 54 11 11 GND DLP_MOT_CLR_REM 4
CLN_SOL_RET 55 55 10 10 CLN_SOL_RET GND 5
CLN_SOL_REM 56 56 9 9 CLN_SOL_REM +24V1 6
REG SENS_R_S(BK)
_ 57 57 8 8 REG SENS_R_S(BK)
_
REG_SENS_R_P(BK) 58 58 7 7 REG_SENS_R_P(BK)
REG_R_LED 59 59 6 6 REG_R_LED
GND 60 60 5 5 GND
REG_SENS_F_S 61 61 4 4 REG_SENS_F_S
YC22
REG_SENS_F_P 62 62 3 3 REG_SENS_F_P REG_CL_REM 2 1 3 3
REG_F_LED 63 63 2 2 REG_F_LED YC9 2 2 RCL
GND 64 64 1 1 GND DRM_MOT_BK_BRK 1 24V2 1 2 1 1
DRM_MOT_BK_DIR 2
DRM_MOT_BK_RDY 3
YC5 YC2 DRM_MOT_BK_CLK 4
GND 1 1 50 50 GND DRM_MOT_BK_REM 5
YC25
M_TEMP 2 2 49 49 M_TEMP GND 6
LOOP_SENS 3 3 48 48 LOOP_SENS +24V2 7 REG_MOT_B/ 1
GND 4 4 47 47 GND REG_MOT_A/ 2
EDGE_FAN_H 5 5 46 46 EDGE_FAN_H REG_MOT_B 3
DU1_MOT_PD 6 6 45 45 DU1_MOT_PD REG_MOT_A 4
DU1_MOT_CLK 7 7 44 44 DU1_MOT_CLK
DU1_MOT_REM(CL_H) 8 8 43 43 DU1_MOT_REM(CL_H)
GND 9 9 42 42 GND
EXIT_FAN 10 10 41 41 EXIT_FAN YC7
DU_ENTER_SENS 11 11 40 40 DU_ENTER_SENS DRM_MOT_CLR_BRK 1
TCON_SET 12 12 39 39 TCON_SET DRM_MOT_CLR_DIR 2
GND 13 13 38 38 GND DRM_MOT_CLR_RDY 3
TRANS_MOT_REM 14 14 37 37 TRANS_MOT_REM DRM_MOT_CLR_CLK 4
TRANS_MOT_CLK 15 15 36 36 TRANS_MOT_CLK DRM_MOT_CLR_REM 5
TRANS_MOT_RDY 16 16 35 35 TRANS_MOT_RDY GND 6
TRANS_MOT_DIR 17 17 34 34 TRANS_MOT_DIR +24V1 7
TRANS_MOT_BRK 18 18 33 33 TRANS_MOT_BRK
GND 19 19 32 32 GND
DRM_MOT_BK_REM 20 20 31 31 DRM_MOT_BK_REM
DRM_MOT_BK_RDY 21 21 30 30 DRM_MOT_BK_RDY
DRM_MOT_BK_DIR 22 22 29 29 DRM_MOT_BK_DIR
DRM_MOT_BK_BRK 23 23 28 28 DRM_MOT_BK_BRK
GND 24 24 27 27 GND
DLP_MOT_BK_REM 25 25 26 26 DLP_MOT_BK_REM
DLP_MOT_BK_CLK 26 26 25 25 DLP_MOT_BK_CLK
DLP_MOT_BK_RDY 27 27 24 24 DLP_MOT_BK_RDY
DLP_MOT_BK_DIR 28 28 23 23 DLP_MOT_BK_DIR
GND 29 29 22 22 GND
DRM_MOT_CLR_REM 30 30 21 21 DRM_MOT_CLR_REM YC21
DRM_MOT_BK_CLR_CLK 31 31 20 20 DRM_MOT_BK_CLR_CLK 24V2 1
DRM_MOT_CLR_RDY 32 32 19 19 DRM_MOT_CLR_RDY FSR_CL_REM 2
DRM_MOT_CLR_DIR 33 33 18 18 DRM_MOT_CLR_DIR N.C 3
GND 34 34 17 17 GND
DLP_MOT_CLR_REM 35 35 16 16 DLP_MOT_CLR_REM
DLP_MOT_CLR_CLK 36 36 15 15 DLP_MOT_CLR_CLK
DLP_MOT_CLR_RDY 37 37 14 14 DLP_MOT_CLR_RDY
DLP_MOT_CLR_DIR 38 38 13 13 DLP_MOT_CLR_DIR
GND 39 39 12 12 GND
REG_MOT_PD 40 40 11 11 REG_MOT_PD
REG_MOT_CLK 41 41 10 10 REG_MOT_CLK
REG_MOT_REM(CL) 42 42 9 9 REG_MOT_REM(CL)
GND 43 43 8 8 GND
IH_PWB_FAN_L 44 44 7 7 IH_PWB_FAN_L
IH_PWB_FAN_H 45 45 6 6 IH_PWB_FAN_H
IH PWB_FAN_ALM
_ 46 46 5 5 IH PWB_FAN_ALM
_
POWER_OFF 47 47 4 4 POWER_OFF FPWB1
DRM_HEAT_REM 48 48 3 3 DRM_HEAT_REM
IH_PWB_FAN(U)_AL 49 49 2 2 IH_PWB_FAN(U)_AL
GND 50 50 1 1 GND
EPWB
2-4-18
2LK/2LN/2LM/2LC
YC6 YC1
GND 1 1 64 64 GND
JOB_SET 2 2 63 63 JOB_SET Fuser drive unit
JOB_MOT_REM 3 3 62 62 JOB_MOT_REM
YC10
JOB MOT_CLK
_ 4 4 61 61 JOB MOT_CLK
_ GND 1 1
JOB_MOT_DIR 5 5 60 60 JOB_MOT_DIR M_TEMP 2 2
JOB_OPEN_SENS 6 6 59 59 JOB_OPEN_SENS
JOB_SOL_REM 7 7 58 58 JOB_SOL_REM YC18
GND 8 8 57 57 GND FSR_MOT_BRK 1 1 3.3V 3 3 1 1 +3.3V ID sensor
MAIN_HEAT_REM 9 9 56 56 MAIN_HEAT_REM FSR_MOT_DIR 2 2 6 6 CW/CCW REG_F_LED 4 4 2 2 LED_REF
SUB_HEAT_REM 10 10 55 55 SUB_HEAT_REM FSR_MOT_RDY 3 3 5 5 LD GND 5 5 3 3 GND IDS1
ZEROC 11 11 54 54 ZEROC FSR_MOT_CLK 4 4 4 4 CLOCK REG SENS_F_P
_ 6 6 4 4 VO_P
FSR_RELAY 12 12 53 53 FSR_RELAY FSR_MOT_REM 5 5 3 3 START/STOP FUM REG_SENS_F_S 7 7 5 5 VO_S
PRESS_REM 13 13 52 52 PRESS_REM GND 6 6 2 2 GND
EXIT REAR_FAN_L
_ 14 14 51 51 EXIT REAR_FAN_L
_ 24V2 7 7 1 1 +24V
EXIT_REAR_FAN_H 15 15 50 50 EXIT_REAR_FAN_H 3.3V 8 8 1 1 +3.3V
GND 16 16 49 49 GND REG_R_LED 9 9 2 2 LED_REF
FSR_CL_REM 17 17 48 48 FSR_CL_REM GND 10 10 3 3 GND IDS2
FSR_MOT_REM 18 18 47 47 FSR_MOT_REM REG_SENS_R_P 11 11 4 4 VO_P
FSR_MOT_CLK 19 19 46 46 FSR_MOT_CLK REG_SENS_R_S 12 12 5 5 VO_S
FSR_MOT_RDY 20 20 45 45 FSR_MOT_RDY CN1 CN2
FSR_MOT_DIR 21 21 44 44 FSR_MOT_DIR 11 11 SIG2 +5V 1
FSR_MOT_BRK 22 22 43 43 FSR_MOT_BRK 10 10 SIG1 S.GND 2 24V 13 13 3 1 COM
GND 23 23 42 42 GND
YC13 9 9 SGND SIG_1 3 CLN_SOL_REM
CLN_SOL_RET
14 14 2 Relay 2 ACT CLSOL
MPF_TABLE 24 24 41 41 MPF_TABLE 8 8 +5V +5V 4 15 15 1 3 RET
MPF_WID1 25 25 40 40 MPF_WID1 TRANS_MOT_BRK 1 1 7 7 BRAKE S.GND 5
MPF_WID2 26 26 39 39 MPF_WID2 TRANS_MOT_DIR 2 2 6 6 CW/CCW SIG_2 6
MPF_WID3 27 27 38 38 MPF_WID3 TRANS_MOT_RDY 3 3 5 5 FG
MPF_LNG 28 28 37 37 MPF_LNG TRANS_MOT_CLK 4 4 4 4 VM
GND 29 29 36 36 GND TRANS_MOT_REM 5 5 3 3 START/STOP
MPF_PPR_SET 30 30 35 35 MPF_PPR_SET GND 6 6 2 2 PGND
MPF_LIFT_UP 31 31 34 34 MPF_LIFT_UP 24V2 7 7 1 1 +24V1
TRM
MPF_LIFT_DOWN 32 32 33 33 MPF_LIFT_DOWN GND 8 8 Job separator
MPF_JAM 33 33 32 32 MPF_JAM 24V2 9 9
MPF_CL 34 34 31 31 MPF_CL TANK_SET 10 10 JMPWB
MPF_LIF2 35 35 30 30 MPF_LIF2
MPF_LIFT1 36 36 29 29 MPF_LIFT1
GND 37 37 28 28 GND YC8
TC_MOT_LOCK 38 38 27 27 TC_MOT_LOCK DLP_MOT_BK_DIR 1 YC2
TC_TONER_LED 39 39 26 26 TC_TONER_LED DLP_MOT_BK_RDY 2 GND 1 1 3 3 GND
TC TONER_FULL
_ 40 40 25 25 TC TONER_FULL
_ DLP_MOT_BK_CLK 3 YC20 YC1 JOB_OPEN_SENS 2 2 2 2 Vout JOCS
TC_TONER_VCONT 41 41 24 24 TC_TONER_VCONT DLP_MOT_BK_REM 4 JOB_SET 1 1 10 1 10 10 JOB_SET +5V1 3 3 1 1 5V
INTER_LOCK 42 42 23 23 INTER_LOCK GND 5 GND 2 2 9 2 9 9 GND
DU2_PD 43 43 22 22 DU2_PD +24V1 6 GND 3 3 8 3 8 8 GND JOB_B/ 4 4 4 B/
DU2_CLK 44 44 21 21 DU2_CLK JOB_MOT_REM 4 4 7 4 7 7 JOB_MOT_REM JOB_A/ 5 5 3 3 A/
DU2_REM_(CL_LOW) 45 45 20 20 DU2_REM_(CL_LOW) 24V1 5 5 6
Relay
5 6 6 24V1 JOB_B 6 6 2 2 B JEM
GND 46 46 19 19 GND JOB_MOT_CLK 6 6 5 6 5 5 JOB_MOT_CLK JOB_A 7 7 1 1 A
DU_OPEN 47 47 18 18 DU_OPEN 5V 7 7 4 7 4 4 5V
DU_FAN 48 48 17 17 DU_FAN JOB_MOT_DIR 8 8 3 8 3 3 JOB_MOT_DIR
PRESS_MOT_REM1 49 49 16 16 PRESS_MOT_REM1 JOB_OPEN_SENS 9 9 2 9 2 2 JOB_OPEN_SENS +24V1 8 8 2 1 COM
PRESS_MOT_REM2 50 50 15 15 PRESS_MOT_REM2 YC6 JOB SOL_REM
_ 10 10 1 10 1 1 JOB_SOL_REM JOB_SOL_OUT 9 9 1 2 ACT JFSSOL
PRESS_RLS_SENS 51 51 14 14 PRESS_RLS_SENS DLP_MOT_CLR_DIR 1 NC 11 11
DU_SENS 52 52 13 13 DU_SENS DLP_MOT_CLR_RDY 2
BELT_JAM_SENS 53 53 12 12 BELT_JAM_SENS DLP_MOT_CLR_CLK 3
GND 54 54 11 11 GND DLP_MOT_CLR_REM 4
CLN_SOL_RET 55 55 10 10 CLN_SOL_RET GND 5
CLN_SOL_REM 56 56 9 9 CLN_SOL_REM +24V1 6
REG SENS_R_S(BK)
_ 57 57 8 8 REG SENS_R_S(BK)
_
REG_SENS_R_P(BK) 58 58 7 7 REG_SENS_R_P(BK)
REG_R_LED 59 59 6 6 REG_R_LED
GND 60 60 5 5 GND
REG_SENS_F_S 61 61 4 4 REG_SENS_F_S
YC22
REG_SENS_F_P 62 62 3 3 REG_SENS_F_P REG_CL_REM 2
REG_F_LED 63 63 2 2 REG_F_LED YC9
GND 64 64 1 1 GND DRM_MOT_BK_BRK 1 24V2 1
DRM_MOT_BK_DIR 2
DRM_MOT_BK_RDY 3
YC5 YC2 DRM_MOT_BK_CLK 4
GND 1 1 50 50 GND DRM_MOT_BK_REM 5
YC25
M_TEMP 2 2 49 49 M_TEMP GND 6
LOOP_SENS 3 3 48 48 LOOP_SENS +24V2 7 REG_MOT_B/ 1 1 4 4 B/
GND 4 4 47 47 GND REG_MOT_A/ 2 2 3 3 A/
EDGE_FAN_H 5 5 46 46 EDGE_FAN_H REG_MOT_B 3 3 2 2 B RM
DU1_MOT_PD 6 6 45 45 DU1_MOT_PD REG_MOT_A 4 4 1 1 A
DU1_MOT_CLK 7 7 44 44 DU1_MOT_CLK
DU1_MOT_REM(CL_H) 8 8 43 43 DU1_MOT_REM(CL_H)
GND 9 9 42 42 GND
EXIT_FAN 10 10 41 41 EXIT_FAN YC7
DU_ENTER_SENS 11 11 40 40 DU_ENTER_SENS DRM_MOT_CLR_BRK 1
TCON_SET 12 12 39 39 TCON_SET DRM_MOT_CLR_DIR 2
GND 13 13 38 38 GND DRM_MOT_CLR_RDY 3
TRANS_MOT_REM 14 14 37 37 TRANS_MOT_REM DRM_MOT_CLR_CLK 4
TRANS_MOT_CLK 15 15 36 36 TRANS_MOT_CLK DRM_MOT_CLR_REM 5
TRANS_MOT_RDY 16 16 35 35 TRANS_MOT_RDY GND 6
TRANS_MOT_DIR 17 17 34 34 TRANS_MOT_DIR +24V1 7
TRANS_MOT_BRK 18 18 33 33 TRANS_MOT_BRK
GND 19 19 32 32 GND
DRM_MOT_BK_REM 20 20 31 31 DRM_MOT_BK_REM
DRM_MOT_BK_RDY 21 21 30 30 DRM_MOT_BK_RDY
DRM_MOT_BK_DIR 22 22 29 29 DRM_MOT_BK_DIR
DRM_MOT_BK_BRK 23 23 28 28 DRM_MOT_BK_BRK
GND 24 24 27 27 GND
DLP_MOT_BK_REM 25 25 26 26 DLP_MOT_BK_REM
DLP_MOT_BK_CLK 26 26 25 25 DLP_MOT_BK_CLK
DLP_MOT_BK_RDY 27 27 24 24 DLP_MOT_BK_RDY
DLP_MOT_BK_DIR 28 28 23 23 DLP_MOT_BK_DIR
GND 29 29 22 22 GND
DRM_MOT_CLR_REM 30 30 21 21 DRM_MOT_CLR_REM YC21
DRM_MOT_BK_CLR_CLK 31 31 20 20 DRM_MOT_BK_CLR_CLK 24V2 1
DRM_MOT_CLR_RDY 32 32 19 19 DRM_MOT_CLR_RDY FSR_CL_REM 2
DRM_MOT_CLR_DIR 33 33 18 18 DRM_MOT_CLR_DIR N.C 3
GND 34 34 17 17 GND
DLP_MOT_CLR_REM 35 35 16 16 DLP_MOT_CLR_REM
DLP_MOT_CLR_CLK 36 36 15 15 DLP_MOT_CLR_CLK
DLP_MOT_CLR_RDY 37 37 14 14 DLP_MOT_CLR_RDY
DLP_MOT_CLR_DIR 38 38 13 13 DLP_MOT_CLR_DIR
GND 39 39 12 12 GND
REG_MOT_PD 40 40 11 11 REG_MOT_PD
REG_MOT_CLK 41 41 10 10 REG_MOT_CLK
REG_MOT_REM(CL) 42 42 9 9 REG_MOT_REM(CL)
GND 43 43 8 8 GND
IH_PWB_FAN_L 44 44 7 7 IH_PWB_FAN_L
IH_PWB_FAN_H 45 45 6 6 IH_PWB_FAN_H
IH PWB_FAN_ALM
_ 46 46 5 5 IH PWB_FAN_ALM
_
POWER_OFF 47 47 4 4 POWER_OFF FPWB1
IH_PWB_FAN(U)_AL 49 49 2 2 IH_PWB_FAN(U)_AL
GND 50 50 1 1 GND
EPWB
2-4-19
2LK/2LN/2LM/2LC
YC16
DU1_B/ 1 1
DU1_A/ 2 2
DU1_B 3 3
FPWB1 DU1_A 4 4
EDGE_FAN_REM 5 5 2 1 -
24V2 6 6 1 Relay 2 + FUFM1
24V2 8 8 1
Relay
2 + FUFM2
YC23 YC13
3.3V 12 12 1 C31 C31 12 1 1 3.3V
LOOP_SENS 11 11 2 C32 C32 11 2 2 LOOP_SENS YC8
EDGE_FAN_REM 10 10 3 C33 C33 10 3 3 EDGE_FAN_REM 24V2 1 1 1
DU1_A 9 9 4 C34 C34 9 4 4 DU1_A DU_FAN_REM 2 2 2 YC11
DU1_B 8 8 5 C35 C35 8 5 5 DU1_B Relay GND 1 1 3 3 GND
DU1_A/
DU1_B/
7
6
7
6
6
7
C36
C37
C36
C37
7
6
6
7
6
7
DU1_A/
DU1_B/
24V2
DU_FAN_REM
3
4
3
4
2
1
DU_ENTER_SENS
5V
2
3
2
3
2
1
2
1
Vout
5V
DUS1
GND 5 5 8 C38 C38 5 8 8 GND
DU_CL_UPPER_REM 4 4 9 C39 C39 4 9 9 DU_CL_UPPER_REM EXIT_FAN_REM 4 4 2 1 -
24V2 3 3 10 C40 C40 3 10 10 24V2 24V2 5 5 1
Relay
2 + EFM1
EXIT_FAN 2 2 11 C41 C41 2 11 11 EXIT_FAN
DU_ENTER_SENS 1 1 12 C42 C42 1 12 12 DU_ENTER_SENS EXIT_FAN_REM 6 6 2 1 -
24V2 7 7 1
Relay
2 + EFM2
24V2 8 8 3 3
YC17 YC12
DU_CL_UPPER_REM
2 2 DUCL1
GND
GND
20
19
20
19
1
2
B11
B12
B11
B12
20
19 2
1 1
2
GND
GND
MP tray 9 9 1 1
MPF_TABLE 18 18 3 B13 B13 18 3 3 MPF_TABLE

MPF_WID1 17 17 4 B14 B14 17 4 4 MPF_WID1 YC3 YC10
MPF_WID2 16 16 5 B15 B15 16 5 5 MPF_WID2 MPF_LIFT_DR_B 16 16 1 16 1 2 LOOP_SENS 1 1 1 1 OUT
MPF_WID3 15 15 6 B16 B16 15 6 6 MPF_WID3 MPF_LIFT_DR_A 15 15 2 15 2
Relay
1 MPLM GND 2 2 2 2 GND LPS
MPF_LNG 14 14 7 B17 B17 14 7 7 MPF_LNG 5V 3 3 3 3 5V
LED_3.3V3 13 13 8 B18 B18 13 8 8 LED_3.3V3 24V2 14 14 3 14 1 1
MPF_PPR_SET 12 12 9 B19 B19 12 9 9 MPF_PPR_SET 2 2 MPPFCL 3.3V 4 4
MPF_LIFT_UP_SENS 11 11 10 B20 B20 11 10 10 MPF_LIFT_UP_SENS MPF_CL_REM 13 13 4 13 3 3 REG_BK_LED 5 5
MPF_LIFT_DOWN_SENS 10 10 11 B21 B21 10 11 11 MPF_LIFT_DOWN_SENS GND 6 6
MPF_JAM_SENS 9 9 12 B22 B22 9 12 12 MPF_JAM_SENS 5V 12 12 5 12 1 1 5V REG_BK_SENS1_P 7 7
MPF_CL_REM 8 8 13 B23 B23 8 13 13 MPF_CL_REM MPF_JAM_SENS 11 11 6 11 2 2 Vout MPFS REG_BK_SENS1_S 8 8
24V2 7 7 14 B24 B24 7 14 14 24V2 GND 10 10 7 10 3 3 GND
MPF_LIFT_MOT_A 6 6 15 B25 B25 6 15 15 MPF_LIFT_MOT_A Relay GND 9 9
MPF_LIFT_MOT_B 5 5 16 B26 B26 5 16 16 MPF_LIFT_MOT_B 5V 9 9 8 9 1 1 5V BELT_JAM_SENS 10 10
TC TONER_MOT_A
_ 4 4 17 B27 B27 4 17 17 TC TONER_MOT_A
_ MPF_LIFT_DOWN_SENS 8 8 9 8 2 2 Vout MPLS2 5V 11 11
TC_TONER_MOT_B 3 3 18 B28 B28 3 18 18 TC_TONER_MOT_B GND 7 7 10 7 3 3 GND
TC_TONER_FULL 2 2 19 B29 B29 2 19 19 TC_TONER_FULL
TC_TONER_LED 1 1 20 B30 B30 1 20 20 TC_TONER_LED 5V 6 6 11 6 1 1 5V YC14
MPF_LIFT_UP_SENS 5 5 12 5 2 2 Vout MPLS1 GND
PRESS_RLS_SENS
1 1 3 3 GND
GND 4 4 13 4 3 3 GND 2 2 2 2 Vout TRRS
Drawer
Drawer
5V 3 3 1 1 5V
MPF_PPR_SET 3 3 14 3 1 1 Vout
GND 2 2 15 2 2 2 GND MPPS PRESS_RLS_REM1 4 4 2 1
LED_3.3V3 1 1 16 1 3 3 3.3V PRESS_RLS_REM2 5 5 1
Relay
2 TRRM
YC14 YC1 NC 6 6
5V_LED 18 18 1 D43 D43 18 1 1 5V_LED
DU2_A 17 17 2 D44 D44 17 2 2 DU2_A
DU2_B 16 16 3 D45 D45 16 3 3 DU2_B YC4
DU2_A/ 15 15 4 D46 D46 15 4 4 DU2_A/
YC2 24V2 1
DU2_B/ 14 14 5 D47 D47 14 5 5 DU2_B/ MPF_TABLE 9 9 1 9 1 1 Vout ID_SOL_REM 2
DU_OPEN_SW 13 13 6 D48 D48 13 6 6 DU_OPEN_SW GND 8 8 2 8 2 2 GND MPTSW
DU_CL_LOWER_REM 12 12 7 D49 D49 12 7 7 DU_CL_LOWER_REM
DU_FAN 11 11 8 D50 D50 11 8 8 DU_FAN MPF_WID1 7 7 3 7 1 1 WID1
24V2 10 10 9 D51 D51 10 9 9 24V2 GND 6 6 4 6 2 2 GND
PRESS_RLSMOT2 9 9 10 D52 D52 9 10 10 PRESS_RLSMOT2 MPF_WID2 5 5 5 Relay 5 3 3 WID2 MPPWSW
PRESS_RLSMOT21 8 8 11 D53 D53 8 11 11 PRESS_RLSMOT21 MPF_WID3 4 4 6 4 4 WID3
5V 7 7 12 D54 D54 7 12 12 5V
PRESS_RLS_SENS 6 6 13 D55 D55 6 13 13 PRESS_RLS_SENS 5V 3 3 7 3 1 3 1 1 5V
DU_SENS 5 5 14 D56 D56 5 14 14 DU_SENS MPF_LNG 2 2 8 2 2 Relay 2 2 2 Vout MPPLSW
BELT_JAM_SENS 4 4 15 D57 D57 4 15 15 BELT_JAM_SENS GND 1 1 9 1 3 1 3 3 GND
REG_BK_SENS1_S 3 3 16 D58 D58 3 16 16 REG_BK_SENS1_S
REG_BK_SENS1_P 2 2 17 D59 D59 2 17 17 REG_BK_SENS1_P
REG_BK_LED 1 1 18 D60 D60 1 18 18 REG_BK_LED YC9
GND 1 1 3 3 GND
DU_SENS 2 2 2 2 Vout DUS2
YC5 5V 3 3 1 1 5V
A1 A1 1 TANK_SET
YC6
A2 A2 2 +24V2 24V2 7
A3 A3 3 GND GND 6 YC7
A4 A4 4 +24V2 TRANS_MOT_REM 5 24V2 1 1 3 3
A5 A5 5 GND TRANS_MOT_CLK 4 2 2 DUCL2
A6 A6 6 TRANS_MOT_REM TRANS_MOT_RDY 3 DU_CL2_REM 2 2 1 1
A7 A7 7 TRANS_MOT_CLK TRANS_MOT_DIR 2
A8 A8 8 TRANS_MOT_RDY TRANS_MOT_BRK 1 DU_OPEN 3 3 2 2
A9 A9 9 TRANS_MOT_DIR GND 4 4 1 1 DUCSW
A10 A10 10 TRANS_MOT_BRK
DU2_B/ 5 5
DU2_A/ 6 6
DU2_B 7 7
DU2_A 8 8
RYPWB
2-4-20
2LK/2LN/2LM/2LC
YC16
DU1_B/ 1 1 4 4 B/
DU1_A/ 2 2 3 3 A/
DU1_B 3 3 2 2 B DUM1
FPWB1 DU1_A 4 4 1 1 A
24V2 6 6 1 Relay 2 + FUFM1
24V2 8 8 1
Relay
2 + FUFM2
YC23 YC13
3.3V 12 12 1 C31 C31 12 1 1 3.3V
LOOP_SENS 11 11 2 C32 C32 11 2 2 LOOP_SENS YC8
EDGE_FAN_REM 10 10 3 C33 C33 10 3 3 EDGE_FAN_REM 24V2 1 1 4
DU1_A 9 9 4 C34 C34 9 4 4 DU1_A DU_FAN_REM 2 2 3 YC11
DU1_B 8 8 5 C35 C35 8 5 5 DU1_B Relay GND 1 1 3 3 GND
DU1_A/
DU1_B/
7
6
7
6
6
7
C36
C37
C36
C37
7
6
6
7
6
7
DU1_A/
DU1_B/
24V2
DU_FAN_REM
3
4
3
4
2
1
DU_ENTER_SENS
5V
2
3
2
3
2
1
2
1
Vout
5V
DUS1
GND 5 5 8 C38 C38 5 8 8 GND
DU_CL_UPPER_REM 4 4 9 C39 C39 4 9 9 DU_CL_UPPER_REM EXIT_FAN_REM 4 4 2 1 -
24V2 3 3 10 C40 C40 3 10 10 24V2 24V2 5 5 1
Relay
2 + EFM1
EXIT_FAN 2 2 11 C41 C41 2 11 11 EXIT_FAN
DU_ENTER_SENS 1 1 12 C42 C42 1 12 12 DU_ENTER_SENS EXIT_FAN_REM 6 6 2 1 -
24V2 7 7 1
Relay
2 + EFM2
24V2 8 8
YC17 YC12
GND 20 20 1 B11 B11 20 1 1 GND MP tray DU_CL_UPPER_REM 9 9
GND 19 19 2 B12 B12 19 2 2 GND
MPF_TABLE 18 18 3 B13 B13 18 3 3 MPF_TABLE
MPF_WID1 17 17 4 B14 B14 17 4 4 MPF_WID1 YC3 YC10
MPF_WID2 16 16 5 B15 B15 16 5 5 MPF_WID2 MPF_LIFT_DR_B 16 16 1 16 1 2 LOOP_SENS 1 1 1 1 OUT
MPF_WID3 15 15 6 B16 B16 15 6 6 MPF_WID3 MPF_LIFT_DR_A 15 15 2 15 2
Relay
1 MPLM GND 2 2 2 2 GND LPS
MPF_LNG 14 14 7 B17 B17 14 7 7 MPF_LNG 5V 3 3 3 3 5V
LED_3.3V3 13 13 8 B18 B18 13 8 8 LED_3.3V3 24V2 14 14 3 14 1 1
MPF_PPR_SET 12 12 9 B19 B19 12 9 9 MPF_PPR_SET 2 2 MPPFCL 3.3V 4 4
MPF_LIFT_UP_SENS 11 11 10 B20 B20 11 10 10 MPF_LIFT_UP_SENS MPF_CL_REM 13 13 4 13 3 3 REG_BK_LED 5 5
MPF_LIFT_DOWN_SENS 10 10 11 B21 B21 10 11 11 MPF_LIFT_DOWN_SENS GND 6 6
MPF_JAM_SENS 9 9 12 B22 B22 9 12 12 MPF_JAM_SENS 5V 12 12 5 12 1 1 5V REG_BK_SENS1_P 7 7
MPF_CL_REM 8 8 13 B23 B23 8 13 13 MPF_CL_REM MPF_JAM_SENS 11 11 6 11 2 2 Vout MPFS REG_BK_SENS1_S 8 8
24V2 7 7 14 B24 B24 7 14 14 24V2 GND 10 10 7 10 3 3 GND
MPF_LIFT_MOT_A 6 6 15 B25 B25 6 15 15 MPF_LIFT_MOT_A Relay GND 9 9
MPF_LIFT_MOT_B 5 5 16 B26 B26 5 16 16 MPF_LIFT_MOT_B 5V 9 9 8 9 1 1 5V BELT_JAM_SENS 10 10
TC TONER_MOT_A
_ 4 4 17 B27 B27 4 17 17 TC TONER_MOT_A
_ MPF_LIFT_DOWN_SENS 8 8 9 8 2 2 Vout MPLS2 5V 11 11
TC_TONER_MOT_B 3 3 18 B28 B28 3 18 18 TC_TONER_MOT_B GND 7 7 10 7 3 3 GND
TC_TONER_FULL 2 2 19 B29 B29 2 19 19 TC_TONER_FULL
TC_TONER_LED 1 1 20 B30 B30 1 20 20 TC_TONER_LED 5V 6 6 11 6 1 1 5V YC14
MPF_LIFT_UP_SENS 5 5 12 5 2 2 Vout MPLS1 GND
PRESS_RLS_SENS
1 1 3 3 GND
GND 4 4 13 4 3 3 GND 2 2 2 2 Vout TRRS
Drawer
Drawer
5V 3 3 1 1 5V
MPF_PPR_SET 3 3 14 3 1 1 Vout
GND 2 2 15 2 2 2 GND MPPS PRESS_RLS_REM1 4 4 2 1
LED_3.3V3 1 1 16 1 3 3 3.3V PRESS_RLS_REM2 5 5 1
Relay
2 TRRM
YC14 YC1 NC 6 6
5V_LED 18 18 1 D43 D43 18 1 1 5V_LED
DU2_A 17 17 2 D44 D44 17 2 2 DU2_A
DU2_B 16 16 3 D45 D45 16 3 3 DU2_B YC4
DU2_A/ 15 15 4 D46 D46 15 4 4 DU2_A/
YC2 24V2 1
DU2_B/ 14 14 5 D47 D47 14 5 5 DU2_B/ MPF_TABLE 9 9 1 9 1 1 Vout ID_SOL_REM 2
DU_OPEN_SW 13 13 6 D48 D48 13 6 6 DU_OPEN_SW GND 8 8 2 8 2 2 GND MPTSW
DU_CL_LOWER_REM 12 12 7 D49 D49 12 7 7 DU_CL_LOWER_REM
DU_FAN 11 11 8 D50 D50 11 8 8 DU_FAN MPF_WID1 7 7 3 7 1 1 WID1
24V2 10 10 9 D51 D51 10 9 9 24V2 GND 6 6 4 6 2 2 GND
PRESS_RLSMOT2 9 9 10 D52 D52 9 10 10 PRESS_RLSMOT2 MPF_WID2 5 5 5 Relay 5 3 3 WID2 MPPWSW
PRESS_RLSMOT21 8 8 11 D53 D53 8 11 11 PRESS_RLSMOT21 MPF_WID3 4 4 6 4 4 WID3
5V 7 7 12 D54 D54 7 12 12 5V
PRESS_RLS_SENS 6 6 13 D55 D55 6 13 13 PRESS_RLS_SENS 5V 3 3 7 3 1 3 1 1 5V
DU_SENS 5 5 14 D56 D56 5 14 14 DU_SENS MPF_LNG 2 2 8 2 2 Relay 2 2 2 Vout MPPLSW
BELT_JAM_SENS 4 4 15 D57 D57 4 15 15 BELT_JAM_SENS GND 1 1 9 1 3 1 3 3 GND
REG_BK_SENS1_S 3 3 16 D58 D58 3 16 16 REG_BK_SENS1_S
REG_BK_SENS1_P 2 2 17 D59 D59 2 17 17 REG_BK_SENS1_P
REG_BK_LED 1 1 18 D60 D60 1 18 18 REG_BK_LED YC9
GND 1 1 3 3 GND
DU_SENS 2 2 2 2 Vout DUS2
YC5 5V 3 3 1 1 5V
A1 A1 1 TANK_SET
YC6
A2 A2 2 +24V2 24V2 7
A3 A3 3 GND GND 6 YC7
A4 A4 4 +24V2 TRANS_MOT_REM 5 24V2 1 1
A5 A5 5 GND TRANS_MOT_CLK 4
A6 A6 6 TRANS_MOT_REM TRANS_MOT_RDY 3 DU_CL2_REM 2 2
A7 A7 7 TRANS_MOT_CLK TRANS_MOT_DIR 2
A8 A8 8 TRANS_MOT_RDY TRANS_MOT_BRK 1 DU_OPEN 3 3 2 2
A9 A9 9 TRANS_MOT_DIR GND 4 4 1 1 DUCSW
A10 A10 10 TRANS_MOT_BRK
DU2_B/ 5 5 4 4 B/
DU2_A/ 6 6 3 3 A/
DU2_B 7 7 2 2 B DUM2
DU2_A 8 8 1 1 A
RYPWB
2-4-21
2LK/2LN/2LM/2LC
YC7 Middle guide unit

YC12 YC11 MID_B/ 1 1
+24V2 1 1 6 6 +24V2 MID_A/ 2 2
+24V2 2 2 5 5 +24V2 MID_B 3 3
+5V 3 3 4 4 +5V MID_A 4 4
GND 4 4 3 3 GND 13 1
GND 5 5 2 2 GND 12 2 4 4 TH
GND 6 6 1 1 GND BEND_SENS 5 5 11 3 3 3 OUT YC13
GND 6 6 10 4 2 2 GND RDS 5V1 3 3 1
5V 7 7 9 5 1 1 5V GND 2 2 2 From CRPWB
CURRENT_SIG 1 1 3
GND 8 8 8 6 3 3 GND
FEED1_SENS 9 9 7 7 2 2 Vout MS
Relay
5V 10 10 6 8 1 1 5V
GND 11 11 5 9 3 3 GND
REG_SENS 12 12 4 10 2 2 Vout RS Paper feed drive unit
5V 13 13 3 11 1 1 5V
FPWB1 MID_CL_REM 14 14 2 12 3 3
24V2 15 15 2 2 MCL YC2
1 13 1 1 FEED_MOT_GAIN 1 1
FEED_MOT_DIR 2 2 6 6 CW/CCW
FEED_MOT_RDY 3 3 5 5 LD
FEED_MOT_CLK 4 4 4 4 CLOCK PFM
YC5 FEED_MOT_REM 5 5 3 3 START/STOP
V-FEED_CL_REM 3 1 3 3 GND 6 6 2 2 GND
24V2 2 2
2
1
2
1
PCCL 24V2 7 7 1 1 +24V
NC 1 3
YC10
ASIST_CL1 1
Primary paper feed unit 24V2 2

YC8
24V2 1 1 12 1
YC4 YC1 PICK_SOL1_REM 2 2 11 2 YC12
GND 1 1 1 1 GND PICK_SOL1_RET 3 3 10 3 ASIST_CL2 1
FEED_MOT_REM 2 2 2 2 FEED_MOT_REM
FEED_MOT_CLK 3 3 3 3 FEED_MOT_CLK 24V2 2
FEED MOT_RDY
_ 4 4 4 4 FEED MOT_RDY
_ LED_5V 4 4 9 4 3 3 5V
FEED_MOT_DIR 5 5 5 5 FEED_MOT_DIR GND 5 5 8 5 2 2 GND PS1
FEED_CL1_REM 6 6 6 6 FEED_CL1_REM CAS1_EMPTY_SENS 6 6 7 6 1 1 Vout
YC4
Relay
FEED_CL2_REM 7 7 7 7 FEED_CL2_REM
ASIST_CL2 8 8 8 8 ASIST_CL2 FEED_CL1_REM 1 1 3 3
LIFT_MOT2_REM 9 9 9 9 LIFT_MOT2_REM LED_5V 7 7 6 7 3 3 5V 2 2 PFCL1
GND 10 10 10 10 GND GND
CAS1_LIFT_UP_SENS
8 8 5 8 2 2 GND LS1 24V2 2 2 1 1
LIFT_MOT1_REM1 11 11 11 11 LIFT_MOT1_REM1 9 9 4 9 1 1 Vout
CAS2_WID 12 12 12 12 CAS2_WID FEED_CL2_REM 3 3 3 3
CAS2_LNG3 13 13 13 13 CAS2_LNG3 2 2 PFCL2
CAS2_LNG2 14 14 14 14 CAS2_LNG2 5V 10 10 3 10 3 3 5V 24V2 4 4 1 1
CAS2_LNG1 15 15 15 15 CAS2_LNG1 CAS1_P0_SENS 11 11 2 11 2 2 Vout FS1
CAS1_WID CAS1_WID
Connector holder
16 16 16 16 GND 12 12 1 12 1 1 GND
CAS1_LNG3 17 17 17 17 CAS1_LNG3
CAS1_LNG2 18 18 18 18 CAS1_LNG2
CAS1_LNG1 19 19 19 19 CAS1_LNG1 24V2 13 1 12 1
GND 20 20 20 20 GND PICK_SOL2_REM 14 2 11 2
CAS2_QUANT2 21 21 21 21 CAS2_QUANT2 PICK_SOL2_RET 15 3 10 3
CAS2_QUANT1 22 22 22 22 CAS2_QUANT1
CAS1_QUANT1 24 24 24 24 CAS1_QUANT1 LED_5V 16 4 9 4 3 3 5V
LIFT_MOT1_LOCK LIFT_MOT1_LOCK YC3
LIFT_MOT2_LOCK
25
26
25
26
25
26
25
26 LIFT_MOT2_LOCK
GND
CAS2_EMPTY_SENS
17
18
5
6
8
7
Relay 5
6
2
1
2
1
GND
Vout
PS2 CAS1_LNG1 1 1 6 1 4 4 SW1
CURRENT_SIG 27 27 27 27 CURRENT_SIG CAS1_LNG2 2 2 5 2 3 3 SW2
V-FEED_CL 28 28 28 28 V-FEED_CL GND 3 3 4 3 2 2 COM PLSW1
COVER_OPEN 29 29 29 29 COVER_OPEN LED_5V 19 7 6 7 3 3 5V CAS1_LNG3 4 4 3 Relay 4 1 1 SW3
FEED2_SENS 30 30 30 30 FEED2_SENS GND 20 8 5 8 2 2 GND LS2
CAS1_P0 31 31 31 31 CAS1_P0 CAS2_LIFT_UP_SENS 21 9 4 9 1 1 Vout CAS1_WID 5 5 2 5 2 2
CAS1_LIFT_UP 32 32 32 32 CAS1_LIFT_UP GND 6 6 1 6 1 1 PWSW1
GND 33 33 33 33 GND
CAS1_EMPTY 34 34 34 34 CAS1_EMPTY 5V 22 10 3 10 3 3 5V
PICK_SOL1_RET 35 35 35 35 PICK_SOL1_RET CAS2_P0_SENS 23 11 2 11 2 2 Vout FS2 CAS2_LNG1 7 7 6 1 4 4 SW1
PICK_SOL1_REM 36 36 36 36 PICK_SOL1_REM GND 24 12 1 12 1 1 GND CAS2_LNG2 8 8 5 2 3 3 SW2
CAS2_P0 37 37 37 37 CAS2_P0 GND 9 9 4 3 2 2 COM PLSW2
CAS2_LIFT_UP 38 38 38 38 CAS2_LIFT_UP CAS2_LNG3 10 10 3 Relay 4 1 1 SW3
CAS2_EMPTY 39 39 39 39 CAS2_EMPTY
PICK_SOL2_RET 40 40 40 40 PICK_SOL2_RET CAS2_WID 11 11 2 5 2 2
PICK_SOL2_REM 41 41 41 41 PICK_SOL2_REM GND 12 12 1 6 1 1 PWSW2
GND 42 42 42 42 GND
REG_SENS 43 43 43 43 REG_SENS
FEED1_SENS 44 44 44 44 FEED1_SENS LIFT_MOT1_RET 13 13 2 2
BEND_SENS 45 45 45 45 BEND_SENS Lower guide unit LIFT_MOT1_DR 14 14 1 1 LM1
Connector holder
MID_MOT_PH 46 46 46 46 MID_MOT_PH
MID_MOT_REM(ROL) 47 47 47 47 MID_MOT_REM(ROL)
YC6
MID_MOT_CLK 48 48 48 48 MID_MOT_CLK LED_5V 1 1 5 1 3 3 5V
MID_MOT_PD 49 49 49 49 MID_MOT_PD GND 2 2 4 2 2 2 GND PCS LIFT_MOT2_RET 15 1 2 2
ASIST_CL1 50 50 50 50 ASIST_CL1 FEED2_SENS LIFT_MOT2_DR LM2
Relay
3 3 3 3 1 1 Vout 16 2 1 1
COVER_OPEN 4 4 2 4 2 2
GND 5 5 1 5 1 1 PCCSW LED_5V 17 3 6 1 3 3 5V
GND
CAS1_QUANT1
18
19
4
5
5
4
2
3
2
1
2
1
GND
Vout
PGS1(U)
Relay
LED_5V 20 6 3 4 3 3 5V
GND
CAS1_QUANT2
21
22
7
8
2
1
5
6
2
1
2
1
GND
Vout
PGS1(L)
LED_ 5V 23 9 6 1 3 3 5V
GND
CAS2_QUANT1
24
25
10
11
5
4
2
3
2
1
2
1
GND
Vout
PGS2(U)
EPWB LED_5V 26 12 3
Relay
4 3 3 5V
GND 27 13 2 5 2 2 GND PGS2(L)
FPWB2 CAS2_QUANT2 28 14 1 6 1 1 Vout
2-4-22
2LK/2LN/2LM/2LC
Middle guide unit

YC7
YC12 YC11 MID_B/ 1 1 13 1 4 1 B/
+24V2 1 1 6 6 +24V2 MID_A/ 2 2 12 2 3 2 A/
+24V2 2 2 5 5 +24V2 MID_B 3 3 11 3 2 3 B MM
+5V 3 3 4 4 +5V MID_A 4 4 10 4 1 4 A
GND 4 4 3 3 GND
GND 5 5 2 2 GND 4 4 TH
GND 6 6 1 1 GND BEND_SENS 5 5 9 5 3 3 OUT YC13
GND 6 6 8 6 2 2 GND RDS 5V1 3 3 1
5V 7 7 7 7 1 1 5V GND 2 2 2 From CRPWB
Relay
CURRENT_SIG 1 1 3
GND 8 8 6 8 3 3 GND
FEED1_SENS
5V
9
10
9
10
5
4
9
10
2
1
2
1
Vout
5V
MS
GND 11 11 3 11 3 3 GND
REG_SENS 12 12 2 12 2 2 Vout RS Paper feed drive unit
5V 13 13 1 13 1 1 5V
FPWB1 MID_CL_REM 14 14
24V2 15 15 YC2
FEED_MOT_GAIN 1 1
FEED_MOT_DIR 2 2 6 6 CW/CCW
FEED_MOT_RDY 3 3 5 5 LD
FEED_MOT_CLK 4 4 4 4 CLOCK PFM
YC5 FEED_MOT_REM 5 5 3 3 START/STOP
V-FEED_CL_REM 3 1 3 3 GND 6 6 2 2 GND
24V2 2 2
2
1
2
1
PCCL 24V2 7 7 1 1 +24V
NC 1 3
YC10
ASIST_CL1 1 1 3 3
Primary paper feed unit 24V2 2 2
2
1
2
1
ASCL1
YC8
24V2 1 1 12 1 3 1 COM
YC4 YC1 PICK_SOL1_REM 2 2 11 2 2 Relay 2 ACT PUSOL1 YC12
GND 1 1 1 1 GND PICK_SOL1_RET 3 3 10 3 1 3 RET ASIST_CL2 1 1 3 3
FEED_MOT_REM 2 2 2 2 FEED_MOT_REM 2 2 ASCL2
FEED_MOT_CLK 3 3 3 3 FEED_MOT_CLK 24V2 2 2 1 1
FEED MOT_RDY
_ 4 4 4 4 FEED MOT_RDY
_ LED_5V 4 4 9 4 3 3 5V
FEED_MOT_DIR 5 5 5 5 FEED_MOT_DIR GND 5 5 8 5 2 2 GND PS1
FEED_CL1_REM 6 6 6 6 FEED_CL1_REM CAS1_EMPTY_SENS 6 6 7 6 1 1 Vout
YC4
Relay
FEED_CL2_REM 7 7 7 7 FEED_CL2_REM
ASIST_CL2 8 8 8 8 ASIST_CL2 FEED_CL1_REM 1 1 3 3
LIFT_MOT2_REM 9 9 9 9 LIFT_MOT2_REM LED_5V 7 7 6 7 3 3 5V 2 2 PFCL1
GND 10 10 10 10 GND GND
CAS1_LIFT_UP_SENS
8 8 5 8 2 2 GND LS1 24V2 2 2 1 1
LIFT_MOT1_REM1 11 11 11 11 LIFT_MOT1_REM1 9 9 4 9 1 1 Vout
CAS2_WID 12 12 12 12 CAS2_WID FEED_CL2_REM 3 3 3 3
CAS2_LNG3 13 13 13 13 CAS2_LNG3 2 2 PFCL2
CAS2_LNG2 14 14 14 14 CAS2_LNG2 5V 10 10 3 10 3 3 5V 24V2 4 4 1 1
CAS2_LNG1 15 15 15 15 CAS2_LNG1 CAS1_P0_SENS 11 11 2 11 2 2 Vout FS1
CAS1_WID CAS1_WID
Connector holder
16 16 16 16 GND 12 12 1 12 1 1 GND
CAS1_LNG3 17 17 17 17 CAS1_LNG3
CAS1_LNG2 18 18 18 18 CAS1_LNG2
CAS1_LNG1 19 19 19 19 CAS1_LNG1 24V2 13 1 12 1 3 1 COM
GND 20 20 20 20 GND PICK_SOL2_REM 14 2 11 2 2 Relay 2 ACT PUSOL2
CAS2_QUANT2 21 21 21 21 CAS2_QUANT2 PICK_SOL2_RET 15 3 10 3 1 3 RET
CAS1_QUANT1 24 24 24 24 CAS1_QUANT1 LED_5V 16 4 9 4 3 3 5V
LIFT_MOT1_LOCK LIFT_MOT1_LOCK YC3
LIFT_MOT2_LOCK
25
26
25
26
25
26
25
26 LIFT_MOT2_LOCK
GND
CAS2_EMPTY_SENS
17
18
5
6
8
7
Relay 5
6
2
1
2
1
GND
Vout
PS2 CAS1_LNG1 1 1 6 1 4 4 SW1
CURRENT_SIG 27 27 27 27 CURRENT_SIG CAS1_LNG2 2 2 5 2 3 3 SW2
V-FEED_CL 28 28 28 28 V-FEED_CL GND 3 3 4 3 2 2 COM PLSW1
COVER_OPEN 29 29 29 29 COVER_OPEN LED_5V 19 7 6 7 3 3 5V CAS1_LNG3 4 4 3 Relay 4 1 1 SW3
FEED2_SENS 30 30 30 30 FEED2_SENS GND 20 8 5 8 2 2 GND LS2
CAS1_P0 31 31 31 31 CAS1_P0 CAS2_LIFT_UP_SENS 21 9 4 9 1 1 Vout CAS1_WID 5 5 2 5 2 2
CAS1_LIFT_UP 32 32 32 32 CAS1_LIFT_UP GND 6 6 1 6 1 1 PWSW1
GND 33 33 33 33 GND
CAS1_EMPTY 34 34 34 34 CAS1_EMPTY 5V 22 10 3 10 3 3 5V
PICK_SOL1_RET 35 35 35 35 PICK_SOL1_RET CAS2_P0_SENS 23 11 2 11 2 2 Vout FS2 CAS2_LNG1 7 7 6 1 4 4 SW1
PICK_SOL1_REM 36 36 36 36 PICK_SOL1_REM GND 24 12 1 12 1 1 GND CAS2_LNG2 8 8 5 2 3 3 SW2
CAS2_P0 37 37 37 37 CAS2_P0 GND 9 9 4 3 2 2 COM PLSW2
CAS2_LIFT_UP 38 38 38 38 CAS2_LIFT_UP CAS2_LNG3 10 10 3 Relay 4 1 1 SW3
CAS2_EMPTY 39 39 39 39 CAS2_EMPTY
PICK_SOL2_RET 40 40 40 40 PICK_SOL2_RET CAS2_WID 11 11 2 5 2 2
PICK_SOL2_REM 41 41 41 41 PICK_SOL2_REM GND 12 12 1 6 1 1 PWSW2
GND 42 42 42 42 GND
REG_SENS 43 43 43 43 REG_SENS
FEED1_SENS 44 44 44 44 FEED1_SENS LIFT_MOT1_RET 13 13 2 2
BEND_SENS 45 45 45 45 BEND_SENS Lower guide unit LIFT_MOT1_DR 14 14 1 1 LM1
Connector holder
MID_MOT_PH 46 46 46 46 MID_MOT_PH
MID_MOT_REM(ROL) 47 47 47 47 MID_MOT_REM(ROL)
YC6
MID_MOT_CLK 48 48 48 48 MID_MOT_CLK LED_5V 1 1 5 1 3 3 5V
MID_MOT_PD 49 49 49 49 MID_MOT_PD GND 2 2 4 2 2 2 GND PCS LIFT_MOT2_RET 15 1 2 2
ASIST_CL1 50 50 50 50 ASIST_CL1 FEED2_SENS LIFT_MOT2_DR LM2
Relay
3 3 3 3 1 1 Vout 16 2 1 1
COVER_OPEN 4 4 2 4 2 2
GND 5 5 1 5 1 1 PCCSW LED_5V 17 3 6 1 3 3 5V
GND
CAS1_QUANT1
18
19
4
5
5
4
2
3
2
1
2
1
GND
Vout
PGS1(U)
Relay
LED_5V 20 6 3 4 3 3 5V
GND
CAS1_QUANT2
21
22
7
8
2
1
5
6
2
1
2
1
GND
Vout
PGS1(L)
LED_ 5V 23 9 6 1 3 3 5V
GND
CAS2_QUANT1
24
25
10
11
5
4
2
3
2
1
2
1
GND
Vout
PGS2(U)
EPWB LED_5V 26 12 3
Relay
4 3 3 5V
GND 27 13 2 5 2 2 GND PGS2(L)
FPWB2 CAS2_QUANT2 28 14 1 6 1 1 Vout
2-4-23
2LK/2LN/2LM/2LC
YC4
NC 1
NC 3
NC 5
NC 7
YC3 DRM_C_BRAKE 9
+24V 1 6 A1 A16 A1 A1 +24V1 DRM C_GAIN
_ 11
GND 2 5 A2 A15 A2 A2 GND DRM_C_CW/CCW 13
START/STOP 3 4 A3 A14 A3 A3 ICL_MOT_ _REM DRM_C_LD 15
TRCM CLOCK 4 3 A4 A13 A4 A4 ICL MOT_CLK
_ DRM_C_CLK 17
LD 5 2 A5 A12 A5 A5 ICL_MOT_RDY DRM_C_S/S 19
CW/CCW 6 1 A6 A11 A6 A6 ICL_MOT_DIR PGND 21
+24V1 23
YC9 YC3
MOT_CLK 1 1 11 11 MOT_CLK
MOT_SDO 2 2 10 10 MOT_SDO
2 1 1 5 A7 A10 A7 A7 RLS_MOT_DR MOT_SEL 3 3 9 9 MOT_SEL
CRM 1
Relay
2 2 4 A8 A9 A8 A8 +24V1 MOT_SDI 4 4 8 8 MOT_SDI
MOT_RDY 5 5 7 7 MOT_RDY
Relay EMERGENCY 6 6 6 6 EMERGENCY NC
GND 3 3 3 3 A9 A8 A9 A9 GND BLT_SPEED 7 7 5 5 BLT_SPEED NC
CRS SIG 2 2 4 2 A10 A7 A10 A10 RLS_SENS BLT_INDEX 8 8 4 4 BLT_INDEX NC
5V 1 1 5 1 A11 A6 A11 A11 +5V DRM_INDEX_BK 9 9 3 3 DRM_INDEX_BK NC
DRM_INDEX_M 10 10 2 2 DRM_INDEX_M DRM_Y_BRAKE 10
DRM_INDEX_C 11 11 1 1 DRM_INDEX_C DRM_Y_GAIN 12
DRM_Y_CW/CCW 14
2 1 A12 A5 A12 A12 ZIG_MOT_DR_CCW DRM_Y_LD 16
DCM Relay A13 A4 A13 A13 ZIG_MOT_DR_CW DRM_Y_CLK 18
Connector holder
Connector holder
1 2
A14 A3 A14 A14 GND DRM_INDEX_Y 12 1 11 22 DRM_INDEX_Y DRM_Y_S/S 20
A15 A2 A15 A15 BLT_INDEX GND 13 2 10 21 GND PGND 22
Relay
A16 A1 A16 A16 +5V GND 14 3 9 20 GND +24V1 24
+5V 15 4 8 19 +5V
+5V 16 5 7 18 +5V
GND 3 3 B1 B16 B1 B1 GND BLT_BRAKE 17 6 6 17 BLT_BRAKE
DCS SIG 2 2 B2 B15 B2 B2 ZIG_SENS BLT_VM 18 7 5 16 BLT_VM
5V 1 1 B3 B14 B3 B3 +5V BLT_REM 19 8 4 15 BLT_REM
MOT_DATA_SET 20 9 3 14 MOT_DATA_SET
YC5
DRM_ON 21 10 2 13 DRM_ON NC 1 1
GND 3 3 1 11 B4 B13 B4 B4 GND BLT_FG 22 11 1 12 BLT_FG NC 3 3
TRBLS SIG 2 2 2 10 B5 B12 B5 B5 BLT_SPEED NC 5 5
5V 1 1 3 9 B6 B11 B6 B6 +5V NC 7 7
DRM_BK_BRAKE 9 9 DRM-K
DRM_BK_GAIN 11 11
TH 4 4 4 8 B7 B10 B7 B7 TEMP DRM_BK_CW/CCW 13 13 6 6 CW/CCW
OUT 3 3 5 7 B8 B9 B8 B8 ZIG_REV_SENS DRM_BK_LD 15 15 5 5 LD
DES GND 2 2 6 Relay 6 B9 B8 B9 B9 GND DRM_BK_CLK 17 17 4 4 CLOCK
5V 1 1 7 5 B10 B7 B10 B10 +5V DRM_BK_S/S 19 19 3 3 START/STOP
PGND 21 21 2 2 GND
+24V1 23 23 1 1 +24V
+3.3V 6 8 4 B11 B6 B11 B11 +3.3V2
EEP_SCL 5 9 3 B12 B5 B12 B12 EEP_SCL2
TRPWB EEP_SDA 4 10 2 B13 B4 B13 B13 EEP_SDA2
GND 3 11 1 B14 B3 B14 B14 GND
A0 2 B15 B2 B15 B15 A0 EPWB MCPWB
A1 1 B16 B1 B16 B16 A1
NC 2 2
NC 4 4
NC 6 6
NC 8 8
DRM_M_BRAKE 10 10 DRM-MCY
DRM_M_GAIN 12 12
RFPWB DRM_M_CW/CCW 14 14 6 6 CW/CCW
DRM_M_LD 16 16 5 5 LD
YC1 YC27 DRM_M_CLK 18 18 4 4 CLOCK
SDA 4 4 1 12 1 1 EEP_SDA2 DRM_M_S/S 20 20 3 3 START/STOP
GND 3 3 2 11 2 2 GND PGND 22 22 2 2 GND
SCL 2 2 3 10 3 3 EEP_SCL2 +24V1 24 24 1 1 +24V
+3.3V 1 1 4 9 4 4 3.3V2
YC6
DLP_Y_GAIN 1
1 2 1 5 5 8 5 5 +24V1 DLP_Y_CW/CCW 2
TM-Y 2 Relay 1 2 4 6 7 6 6 TMOT_Y_DR DLP_Y_LD 3
DLP_Y_CLK 4
Relay DLP_Y_S/S 5
GND 3 3 3 3 7 6 +24V1 PGND 6
SRS-Y SIG
5V
2
1
2
1
4
5
2
1
8 5 8 8 TMOT_C_DR +24V1 7
9 4 9 9 +24V1
10 3 10 10 TMOT_M_DR
1 2 1 5 DLP_C_GAIN 8
TM-C Relay
Connector holder
Connector holder
2 1 2 4 DLP_C_CW/CCW 9
11 2 11 11 +24V1 DLP_C_LD 10
Relay 12 1 12 12 TMOT_Bk_DR DLP_C_CLK 11
Relay
GND 3 3 3 3 DLP_C_S/S 12
SRS-C SIG 2 2 4 2 PGND 13
5V 1 1 5 1 +24V1 14
1 12 1 13 GND
ENCODE_Y
YC7
2
3
11
10
2
3
14
15 +5V DLP_M_GAIN 1 1
DEVM-MCY
1 2 1 5 DLP_M_CW/CCW 2 2 6 6 CW/CCW
TM-M 2 Relay 1 2 4 DLP_M_LD 3 3 5 5 LD
4 9 4 16 GND DLP_M_CLK 4 4 4 4 CLOCK
Relay 5 8 5 17 ENCODE_C DLP_M_S/S 5 5 3 3 START/STOP
GND 3 3 3 3 6 7 6 18 +5V PGND 6 6 2 2 GND
SRS-M SIG
5V
2
1
2
1
4 2
YC22
+24V1 7 7 1 1 +24V
5 1
7 6 7 19 GND LVU_FAN 1 1 6 1 2 1 -
8 5 8 20 ENCODE_M +24V1 2 2 5 2 1
Relay
2 + PSFM
9 4 9 21 +5V DEVM-K
1 2 1 5 DLP_BK_GAIN 8 8
TM-K 2 Relay 1 2 4 DLP_BK_CW/CCW 9 9 6 6 CW/CCW
10 3 10 22 GND Relay DLP_BK_LD 10 10 5 5 LD
Relay 11 2 11 23 ENCODE_K DLP_BK_CLK 11 11 4 4 CLOCK
GND 3 3 3 3 12 1 12 24 +5V DLP_BK_S/S 12 12 3 3 START/STOP
SRS-K SIG 2 2 4 2 3 3 4 3 PGND 13 13 2 2 GND
5V 1 1 5 1 4 4 3 4 +24V1 14 14 1 1 +24V
5 5 2 5
6 6 1 6
2-4-24
2LK/2LN/2LM/2LC
YC4
NC 1 1
NC 3 3
NC 5 5
NC 7 7
YC3 DRM_C_BRAKE 9 9 DRM-C
+24V 1 6 A1 A16 A1 A1 +24V1 DRM C_GAIN
_ 11 11
GND 2 5 A2 A15 A2 A2 GND DRM_C_CW/CCW 13 13 6 6 CW/CCW
START/STOP 3 4 A3 A14 A3 A3 ICL_MOT_ _REM DRM_C_LD 15 15 5 5 LD
TRCM CLOCK 4 3 A4 A13 A4 A4 ICL MOT_CLK
_ DRM_C_CLK 17 17 4 4 CLOCK
LD 5 2 A5 A12 A5 A5 ICL_MOT_RDY DRM_C_S/S 19 19 3 3 START/STOP
CW/CCW 6 1 A6 A11 A6 A6 ICL_MOT_DIR PGND 21 21 2 2 GND
+24V1 23 23 1 1 +24V
YC9 YC3
MOT_CLK 1 1 11 11 MOT_CLK
MOT_SDO 2 2 10 10 MOT_SDO
2 1 1 5 A7 A10 A7 A7 RLS_MOT_DR MOT_SEL 3 3 9 9 MOT_SEL
CRM 1
Relay
2 2 4 A8 A9 A8 A8 +24V1 MOT_SDI 4 4 8 8 MOT_SDI
MOT_RDY 5 5 7 7 MOT_RDY
Relay EMERGENCY 6 6 6 6 EMERGENCY NC
GND 3 3 3 3 A9 A8 A9 A9 GND BLT_SPEED 7 7 5 5 BLT_SPEED NC
CRS SIG 2 2 4 2 A10 A7 A10 A10 RLS_SENS BLT_INDEX 8 8 4 4 BLT_INDEX NC
5V 1 1 5 1 A11 A6 A11 A11 +5V DRM_INDEX_BK 9 9 3 3 DRM_INDEX_BK NC
DRM_INDEX_M 10 10 2 2 DRM_INDEX_M DRM_Y_BRAKE 10 10 DRM-Y
DRM_INDEX_C 11 11 1 1 DRM_INDEX_C DRM_Y_GAIN 12 12
DRM_Y_CW/CCW 14 14 6 6 CW/CCW
2 1 A12 A5 A12 A12 ZIG_MOT_DR_CCW DRM_Y_LD 16 16 5 5 LD
DCM Relay A13 A4 A13 A13 ZIG_MOT_DR_CW DRM_Y_CLK 18 18 4 4 CLOCK
Connector holder
Connector holder
1 2
A14 A3 A14 A14 GND DRM_INDEX_Y 12 1 11 22 DRM_INDEX_Y DRM_Y_S/S 20 20 3 3 START/STOP
A15 A2 A15 A15 BLT_INDEX GND 13 2 10 21 GND PGND 22 22 2 2 GND
Relay
A16 A1 A16 A16 +5V GND 14 3 9 20 GND +24V1 24 24 1 1 +24V
+5V 15 4 8 19 +5V
+5V 16 5 7 18 +5V
GND 3 3 B1 B16 B1 B1 GND BLT_BRAKE 17 6 6 17 BLT_BRAKE
DCS SIG 2 2 B2 B15 B2 B2 ZIG_SENS BLT_VM 18 7 5 16 BLT_VM
5V 1 1 B3 B14 B3 B3 +5V BLT_REM 19 8 4 15 BLT_REM
MOT_DATA_SET 20 9 3 14 MOT_DATA_SET
YC5
DRM_ON 21 10 2 13 DRM_ON NC 1 1
GND 3 3 1 11 B4 B13 B4 B4 GND BLT_FG 22 11 1 12 BLT_FG NC 3 3
TRBLS SIG 2 2 2 10 B5 B12 B5 B5 BLT_SPEED NC 5 5
5V 1 1 3 9 B6 B11 B6 B6 +5V NC 7 7
DRM_BK_BRAKE 9 9 DRM-K
DRM_BK_GAIN 11 11
TH 4 4 4 8 B7 B10 B7 B7 TEMP DRM_BK_CW/CCW 13 13 6 6 CW/CCW
OUT 3 3 5 7 B8 B9 B8 B8 ZIG_REV_SENS DRM_BK_LD 15 15 5 5 LD
DES GND 2 2 6 Relay 6 B9 B8 B9 B9 GND DRM_BK_CLK 17 17 4 4 CLOCK
5V 1 1 7 5 B10 B7 B10 B10 +5V DRM_BK_S/S 19 19 3 3 START/STOP
PGND 21 21 2 2 GND
+24V1 23 23 1 1 +24V
+3.3V 6 8 4 B11 B6 B11 B11 +3.3V2
EEP_SCL 5 9 3 B12 B5 B12 B12 EEP_SCL2
TRPWB EEP_SDA 4 10 2 B13 B4 B13 B13 EEP_SDA2
GND 3 11 1 B14 B3 B14 B14 GND
A0 2 B15 B2 B15 B15 A0 EPWB MCPWB
A1 1 B16 B1 B16 B16 A1
NC 2 2
NC 4 4
NC 6 6
NC 8 8
DRM_M_BRAKE 10 10 DRM-M
DRM_M_GAIN 12 12
RFPWB DRM_M_CW/CCW 14 14 6 6 CW/CCW
DRM_M_LD 16 16 5 5 LD
YC1 YC27 DRM_M_CLK 18 18 4 4 CLOCK
SDA 4 4 1 12 1 1 EEP_SDA2 DRM_M_S/S 20 20 3 3 START/STOP
GND 3 3 2 11 2 2 GND PGND 22 22 2 2 GND
SCL 2 2 3 10 3 3 EEP_SCL2 +24V1 24 24 1 1 +24V
+3.3V 1 1 4 9 4 4 3.3V2
YC6
DLP_Y_GAIN 1
1 2 1 5 5 8 5 5 +24V1 DLP_Y_CW/CCW 2
TM-Y 2 Relay 1 2 4 6 7 6 6 TMOT_Y_DR DLP_Y_LD 3
DLP_Y_CLK 4
Relay DLP_Y_S/S 5
GND 3 3 3 3 7 6 +24V1 PGND 6
SRS-Y SIG
5V
2
1
2
1
4
5
2
1
8 5 8 8 TMOT_C_DR +24V1 7
9 4 9 9 +24V1
10 3 10 10 TMOT_M_DR
1 2 1 5 DLP_C_GAIN 8
TM-C Relay
Connector holder
Connector holder
2 1 2 4 DLP_C_CW/CCW 9
11 2 11 11 +24V1 DLP_C_LD 10
Relay 12 1 12 12 TMOT_Bk_DR DLP_C_CLK 11
Relay
GND 3 3 3 3 DLP_C_S/S 12
SRS-C SIG 2 2 4 2 PGND 13
5V 1 1 5 1 +24V1 14
1 12 1 13 GND
ENCODE_Y
YC7
2
3
11
10
2
3
14
15 +5V DLP_M_GAIN 1 1
DEVM-MCY
1 2 1 5 DLP_M_CW/CCW 2 2 6 6 CW/CCW
TM-M 2 Relay 1 2 4 DLP_M_LD 3 3 5 5 LD
4 9 4 16 GND DLP_M_CLK 4 4 4 4 CLOCK
Relay 5 8 5 17 ENCODE_C DLP_M_S/S 5 5 3 3 START/STOP
GND 3 3 3 3 6 7 6 18 +5V PGND 6 6 2 2 GND
SRS-M SIG
5V
2
1
2
1
4 2
YC22
+24V1 7 7 1 1 +24V
5 1
7 6 7 19 GND LVU_FAN 1 1 6 1 2 1 -
8 5 8 20 ENCODE_M +24V1 2 2 5 2 1
Relay
2 + PSFM
9 4 9 21 +5V DEVM-K
1 2 1 5 DLP_BK_GAIN 8 8
TM-K 2 Relay 1 2 4 DLP_BK_CW/CCW 9 9 6 6 CW/CCW
10 3 10 22 GND Relay DLP_BK_LD 10 10 5 5 LD
Relay 11 2 11 23 ENCODE_K DLP_BK_CLK 11 11 4 4 CLOCK
GND 3 3 3 3 12 1 12 24 +5V DLP_BK_S/S 12 12 3 3 START/STOP
SRS-K SIG 2 2 4 2 3 3 4 3 PGND 13 13 2 2 GND
5V 1 1 5 1 4 4 3 4 +24V1 14 14 1 1 +24V
5 5 2 5
6 6 1 6
2-4-25
2LK/2LN/2LM/2LC

YC15
+24V1 1 1
N.C 2 2 PCUSW TB1 #250
+24V2 3 3 YC17 LIVE IN 1 1 1
3 1 5V1 From Inlet
To FPWB2 2 2 GND TB2 #250
HVPWB2 1 3 CURRENT_MONI LIVE OUT 1 1 2
YC2 YC16
TR
+24V2
GND
1
2
1
2
1
2
1
2
+24V2
GND
CRPWB
YC5 YC14
POWER_OFF 3 3 1 1 POWER_OFF
GND 1 1 3 3 GND YC10
4 4 FSR_RELAY_REM +24V1 1 1 1
+24V1 2 2 2 To Paper feeder
+24V1 3 3 1
+24V1 4 4 2 To Document finisher
YC1 YC8 YC1 YC3 YC4 YC9 +24V1 5 5 1
T1_CLR_OFF_REM 1 1 12 12 T1_CLR_OFF_REM GND 1 1 8 8 GND +24V1 1 1 1 1 +24V1 +24V1 6 6 5 To ISCPWB
T1_CNT1 2 2 11 11 T1_CNT1 +5V 2 2 7 7 +5V +24V1 2 2 2 2 +24V1 +24V1 7 7
T1_CNT2 3 3 10 10 T1_CNT2 GND 3 3 6 6 GND +24V1 3 3 3 3 +24V1 +24V1 8 8
T1_CNT3 4 4 9 9 T1_CNT3 +12V 4 4 5 5 +12V +12V 4 4 4 4 +12V GND 9 9 3
T1_CNT4 5 5 8 8 T1_CNT4 GND 5 5 4 4 GND GND 5 5 5 5 GND GND 10 10 4
FB_CNT 6 6 7 7 FB_CNT GND 6 6 3 3 GND GND 6 6 6 6 GND GND 11 11 3
T2_REM 7 7 6 6 T2_REM +24V1 7 7 2 2 +24V1 GND 7 7 7 7 GND GND 12 12 4
SP_REM 8 8 5 5 SP_REM +24V1 8 8 1 1 +24V1 GND 8 8 8 8 GND GND 13 13 2
T2_CNT 9 9 4 4 T2_CNT GND 14 14 4
SP_CNT 10 10 3 3 SP_CNT GND 15 15
SGND 11 11 2 2 SGND YC13 YC26 GND 16 16
GND 2 2 3 3 GND
3.3V3 3 3 2 2 3.3V3
3.3V2 4 4 1 1 3.3V2
YC3
IH_NEUTRAL 1 1 1
NC 2 2 To IHPWB
YC16 IH_LIVE 3 3 2
14 14 DC_REC_CNT
13 13 AC_MAG_CLK_Y
YC1 12 12 AC_MAG_CNT_Y FPWB1
DISCHARGE_Y 1 1 11 11 DISCHARGE_Y
AC_MAIN_CNT_Y 2 2 10 10 AC_MAIN_CNT_Y
AC_SLV_CNT_Y 3 3 9 9 AC_SLV_CNT_Y
DC_MAG_CNT_Y 4 4 8 8 DC_MAG_CNT_Y
DC_SLV_CNT_Y 5 5 7 7 DC_SLV_CNT_Y
AC_SLV_CLK_Y 6 6 6 6 AC_SLV_CLK_Y
MAIN_IDC_Y 7 7 5 5 MAIN_IDC_Y
DC_MAIN_CNT_Y 8 8 4 4 DC_MAIN_CNT_Y
DC_MAIN_REM 9 9 3 3 DC_MAIN_REM
AC_MAIN_CLK 10 10 2 2 AC_MAIN_CLK
SGND 11 11 1 1 SGND
4 DH_LIVE
TB3 #110 2 MSW_IN MSW
DH_LIVE 1 1 1 MSW_OUT
YC2
SGND 1 1 14 28 SGND
DC_MAIN_CNT_C 2 2 13 27 DC_MAIN_CNT_C YC1 2
MAIN_IDC_C 3 3 12 26 MAIN_IDC_C MSW_OUT 1 1 To CRPWB
DC_MAG_REM 4 4 11 25 DC_MAG_REM MSW_IN 2 2 1
AC_SLV_CLK_C 5 5 10 24 AC_SLV_CLK_C
DC_SLV_CNT_C 6 6 9 23 DC_SLV_CNT_C TB1 #250
DC_MAG_CNT_C 7 7 8 22 DC_MAG_CNT_C LIVE 1 1 AC_LIVE
AC_SLV_CNT_C 8 8 7 21 AC_SLV_CNT_C
AC_MAIN_CNT_C 9 9 6 20 AC_MAIN_CNT_C TB2 #250 Inlet
DISCHARGE_C 10 10 5 19 DISCHARGE_C NEUTRAL 1 1 AC_NEUTRAL
4 18 AC_MAG_CNT_C
3 17 AC_MAG_CLK_C
2 16 DC_REC_REM PSPWB YC4
1 15 NC DH_LIVE_OUT 1 1
2 2
EPWB 3 3 1 1
DH_LIVE_IN 4 4 2 2
YC17
11 11 AC_MAG_CLK_M YC5
YC3 10 10 AC_MAG_CNT_M YC2 YC8 DH_LIVE 1 1
DISCHARGE_M 1 1 9 9 DISCHARGE_M +24V1 6 6 1 1 +24V1 DH_LIVE 2 2 1 1
AC_MAIN_CNT_M 2 2 8 8 AC_MAIN_CNT_M +24V1 5 5 2 2 +24V1 NC 3 3 2 2 CH
AC_SLV_CNT_M 3 3 7 7 AC_SLV_CNT_M +24V1 4 4 3 3 +24V1 NC 4 4
DC_MAG_CNT_M 4 4 6 6 DC_MAG_CNT_M GND 3 3 4 4 GND DH_NEUTRAL 5 5 1 1
DC_SLV_CNT_M 5 5 5 5 DC_SLV_CNT_M GND 2 2 5 5 GND DH_NEUTRAL 6 6 2 2 CH
AC_SLV_CLK_M 6 6 4 4 AC_SLV_CLK_M GND 1 1 6 6 GND
MAIN_IDC_M 7 7 3 3 MAIN_IDC_M
DC_MAIN_CNT_M 8 8 2 2 DC_MAIN_CNT_M
SGND 9 9 1 1 SGND
MCPWB
SGND 10 10 11 22 SGND
DC_MAIN_CNT_Bk 11 11 10 21 DC_MAIN_CNT_Bk
MAIN_IDC_Bk 12 12 9 20 MAIN_IDC_Bk
AC MAIN_CNT_Bk
_ 13 13 8 19 AC MAIN_CNT_Bk
_
AC_SLV_CLK_Bk 14 14 7 18 AC_SLV_CLK_Bk
DC_SLV_CNT_Bk 15 15 6 17 DC_SLV_CNT_Bk YC6
DC_MAG_CNT_Bk 16 16 5 16 DC_MAG_CNT_Bk YC13 DH_LIVE 1 1 1
AC_SLV_CNT_Bk 17 17 4 15 AC_SLV_CNT_Bk 1 1 +24V1 2 To Paper feeder
DISCHARGE_Bk 18 18 3 14 DISCHARGE_Bk 2 2 +24V1 DH_NEUTRAL 2 3 2
2 13 AC_MAG_CNT_Bk 3 3 +24V1
1 12 AC_MAG_CLK_Bk 4 4 PGND
5 5 PGND
6 6 PGND
YC4
+24V1 1 1
DV +24V1 2 2
PGND 3 3
PGND 4 4
YC5
+24V1 1 1
MC
PGND 2 2
HVPWB1
2-4-26
2LK/2LN/2LM/2LC

YC15
+24V1 1 1
N.C 2 2 PCUSW TB1 #250
+24V2 3 3 YC17 LIVE IN 1 1 1
3 1 5V1 From Inlet
To FPWB2 2 2 GND TB2 #250
HVPWB2 1 3 CURRENT_MONI LIVE OUT 1 1 2
YC2 YC16
TR
+24V2
GND
1
2
1
2
1
2
1
2
+24V2
GND
CRPWB
YC5 YC17
POWER_OFF 3 3 1 1 POWER_OFF
GND 1 1 3 3 GND YC13
4 4 FSR_RELAY_REM +24V1 1 1 1
+24V1 2 2 2 To Paper feeder
+24V1 3 3 1
+24V1 4 4 2 To Document finisher
YC1 YC8 YC1 YC3 YC4 YC12 +24V1 5 5 1
T1_CLR_OFF_REM 1 1 12 12 T1_CLR_OFF_REM GND 1 1 8 8 GND +24V1 1 1 1 1 +24V1 +24V1 6 6 5 To ISCPWB
T1_CNT1 2 2 11 11 T1_CNT1 +5V 2 2 7 7 +5V +24V1 2 2 2 2 +24V1 +24V1 7 7
T1_CNT2 3 3 10 10 T1_CNT2 GND 3 3 6 6 GND +24V1 3 3 3 3 +24V1 +24V1 8 8
T1_CNT3 4 4 9 9 T1_CNT3 +12V 4 4 5 5 +12V +12V 4 4 4 4 +12V GND 9 9 3
T1_CNT4 5 5 8 8 T1_CNT4 GND 5 5 4 4 GND GND 5 5 5 5 GND GND 10 10 4
FB_CNT 6 6 7 7 FB_CNT GND 6 6 3 3 GND GND 6 6 6 6 GND GND 11 11 3
T2_REM 7 7 6 6 T2_REM +24V1 7 7 2 2 +24V1 GND 7 7 7 7 GND GND 12 12 4
SP_REM 8 8 5 5 SP_REM +24V1 8 8 1 1 +24V1 GND 8 8 8 8 GND GND 13 13 2
T2_CNT 9 9 4 4 T2_CNT GND 14 14 4
SP_CNT 10 10 3 3 SP_CNT GND 15 15
SGND 11 11 2 2 SGND YC13 YC26 GND 16 16
GND 2 2 3 3 GND
3.3V3 3 3 2 2 3.3V3
3.3V2 4 4 1 1 3.3V2
YC3
IH_NEUTRAL 1 1 1
NC 2 2 To IHPWB
YC1 YC16 IH_LIVE 3 3 2
DC_REC_CNT 1 1 14 14 DC_REC_CNT
AC_MAG_CLK_Y 2 2 13 13 AC_MAG_CLK_Y TB4
AC_MAG_CNT_Y 3 3 12 12 AC_MAG_CNT_Y FPWB1 NEUTRAL 1
DISCHARGE_Y 4 4 11 11 DISCHARGE_Y
AC_MAIN_CNT_Y 5 5 10 10 AC_MAIN_CNT_Y TB3
AC_SLV_CNT_Y 6 6 9 9 AC_SLV_CNT_Y LIVE 1
DC_MAG_CNT_Y 7 7 8 8 DC_MAG_CNT_Y
DC_SLV_CNT_Y 8 8 7 7 DC_SLV_CNT_Y
AC_SLV_CLK_Y 9 9 6 6 AC_SLV_CLK_Y
MAIN_IDC_Y 10 10 5 5 MAIN_IDC_Y
DC_MAIN_CNT_Y 11 11 4 4 DC_MAIN_CNT_Y
DC_MAIN_REM 12 12 3 3 DC_MAIN_REM YC2
AC_MAIN_CLK 13 13 2 2 AC_MAIN_CLK MSW IN 1
SGND 14 14 1 1 SGND IH_LIVE 2
4 DH_LIVE
TB5 #110 2 MSW_IN MSW
YC5 DH_LIVE 1 1 1 MSW_OUT
YC2 1 1 NEUTRAL_OUT
SGND 1 1 14 28 SGND 2 2 NEUTRAL_IN
DC_MAIN_CNT_C 2 2 13 27 DC_MAIN_CNT_C 3 3 LIVE_OUT YC1 2
MAIN_IDC_C 3 3 12 26 MAIN_IDC_C 4 4 LIVE_IN MSW_OUT 1 1 To CRPWB
DC_MAG_REM 4 4 11 25 DC_MAG_REM MSW_IN 2 2 1
AC_SLV_CLK_C 5 5 10 24 AC_SLV_CLK_C
DC_SLV_CNT_C 6 6 9 23 DC_SLV_CNT_C TB1 #250
DC_MAG_CNT_C 7 7 8 22 DC_MAG_CNT_C LIVE 1 1 AC_LIVE
AC_SLV_CNT_C 8 8 7 21 AC_SLV_CNT_C
AC_MAIN_CNT_C 9 9 6 20 AC_MAIN_CNT_C TB2 #250 Inlet
DISCHARGE_C 10 10 5 19 DISCHARGE_C NEUTRAL 1 1 AC_NEUTRAL
AC_MAG_CNT_C 11 11 4 18 AC_MAG_CNT_C
AC_MAG_CLK_C 12 12 3 17 AC_MAG_CLK_C
DC_REC_REM 13 13 2 16 DC_REC_REM PSPWB YC7
1 15 NC DH_LIVE_OUT 1 1
2 2
EPWB 3 3 1 1
DH_LIVE_IN 4 4 2 2
YC3 YC17
AC_MAG_CLK_M 1 1 11 11 AC_MAG_CLK_M YC8
AC_MAG_CNT_M 2 2 10 10 AC_MAG_CNT_M YC2 YC11 DH_LIVE 1 1
DISCHARGE_M 3 3 9 9 DISCHARGE_M +24V1 6 6 1 1 +24V1 DH_LIVE 2 2 1 1
AC_MAIN_CNT_M 4 4 8 8 AC_MAIN_CNT_M +24V1 5 5 2 2 +24V1 NC 3 3 2 2 CH
AC_SLV_CNT_M 5 5 7 7 AC_SLV_CNT_M +24V1 4 4 3 3 +24V1 NC 4 4
DC_MAG_CNT_M 6 6 6 6 DC_MAG_CNT_M GND 3 3 4 4 GND DH_NEUTRAL 5 5 1 1
DC_SLV_CNT_M 7 7 5 5 DC_SLV_CNT_M GND 2 2 5 5 GND DH_NEUTRAL 6 6 2 2 CH
AC_SLV_CLK_M 8 8 4 4 AC_SLV_CLK_M GND 1 1 6 6 GND
MAIN_IDC_M 9 9 3 3 MAIN_IDC_M
DC_MAIN_CNT_M 10 10 2 2 DC_MAIN_CNT_M
SGND 11 11 1 1 SGND
NC 12 12 YC4
MCPWB LIVE
NC
1
2
YC4 NEUTRAL 3
SGND 1 1 11 22 SGND
DC_MAIN_CNT_Bk 2 2 10 21 DC_MAIN_CNT_Bk
MAIN_IDC_Bk 3 3 9 20 MAIN_IDC_Bk
AC MAIN_CNT_Bk
_ 4 4 8 19 AC MAIN_CNT_Bk
_
AC_SLV_CLK_Bk 5 5 7 18 AC_SLV_CLK_Bk
DC_SLV_CNT_Bk 6 6 6 17 DC_SLV_CNT_Bk YC9
DC_MAG_CNT_Bk 7 7 5 16 DC_MAG_CNT_Bk YC16 DH_LIVE 1 1 1
AC_SLV_CNT_Bk 8 8 4 15 AC_SLV_CNT_Bk 1 1 +24V1 2 To Paper feeder
DISCHARGE_Bk 9 9 3 14 DISCHARGE_Bk 2 2 +24V1 DH_NEUTRAL 2 3 2
AC_MAG_CNT_Bk 10 10 2 13 AC_MAG_CNT_Bk 3 3 +24V1
AC_MAG_CLK_Bk 11 11 1 12 AC_MAG_CLK_Bk 4 4 PGND
5 5 PGND
6 6 PGND
YC5
+24V1 1 1
DV +24V1 2 2
PGND 3 3
PGND 4 4
YC6
+24V1 1 1
MC
PGND 2 2
HVPWB1
2-4-27
2LK/2LN/2LM/2LC
YC2 YC9
GND(AFE_SHP) 1 1 40 40 GND(AFE_SHP) MPWB
CLPIN 2 2 39 39 CLPIN
GND(AFE_SHD) 3 3 38 38 GND(AFE_SHD) YC4 YC25
MCLK 4 4 37 37 AFE_MCLK GND 1 1 1 1 GND
GND 5 5 36 36 GND HTPDN 2 2 2 2 HTPDN
CCDSEL 6 6 35 35 CCDSEL LOCKN 3 3 3 3 LOCKN YC2
GND 7 7 34 34 GND GND 4 4 4 4 GND 1 GND
TXCLK1P 8 8 33 33 DIS_CISCKN TX0N 5 5 5 5 TX0N 2 TXP
TXCLK1N 9 9 32 32 DIS_CISCKP TX0P 6 6 6 6 TX0P
YC10 YC4 3 TXN
GND 10 10 31 31 GND GND 7 7 7 7 GND GND 1 1 GND 4 GND
TXOUTC1P 11 11 30 30 DIS_CIS_5N GND 2 2 GND 5 RXN
TXOUTC1N 12 12 29 29 DIS_CIS_5P 3.3V 3 3 3.3V 6 RXP
GND 13 13 28 28 GND 3.3V 4 4 3.3V 7 GND
TXOUTB1P 14 14 27 27 DIS_CIS_4N 3.3V 5 5 3.3V
TXOUTB1N 15 15 26 26 DIS_CIS_4P 3.3V 6 6 3.3V
GND 16 16 25 25 GND VCLKB 7 7 VCLKB
TXOUTC2P 17 17 24 24 DIS_CIS_3N VSYNCB 8 8 VSYNCB
TXOUTC2N 18 18 23 23 DIS_CIS_3P HSYNCB 9 9 HSYNCB
GND 19 19 22 22 GND MREB 10 10 MREB
TXOUTB2P 20 20 21 21 DIS_CIS_2N GND 11 11 GND
TXOUTB2N 21 21 20 20 DIS_CIS_2P YC3 YC11 DRB0 12 12 DRB0
GND 22 22 19 19 GND SC_CLK 1 1 8 8 SC_CLK DRB1 13 13 DRB1
CCDPWB TXOUTA2P 23 23 18 18 DIS_CIS_1N SC_SO 2 2 7 7 SC_SO DRB2 14 14 DRB2 YC32
TXOUTA2N 24 24 17 17 DIS_CIS_1P SC_SI 3 3 6 6 SC_SI DRB3 15 15 DRB3 3 GND
GND 25 25 16 16 GND SC_BSY 4 4 5 5 SC_BSY DRB4 16 16 DRB4 2 +5V_HDD
SCLK 26 26 15 15 AFECLK SC_HLDN 5 5 4 4 SC_HLDN DRB5 17 17 DRB5 1 GND
SDI 27 27 14 14 AFE_SO SC_DIR 6 6 3 3 SC_DIR DRB6 18 18 DRB6
SENB 28 28 13 13 AFE_EN SC_IRN 7 7 2 2 SC_IRN DRB7 19 19 DRB7
SDO 29 29 12 12 AFE_SI GND(SPARE) 8 8 1 1 GND(SPARE) GND 20 20 GND
SH 30 30 11 11 SH DGB0 21 21 DGB0
TG 31 31 10 10 TG DGB1 22 22 DGB1
GND 32 32 9 9 GND(Mono/Color) DGB2 23 23 DGB2
RS 33 33 8 8 RS DGB3 24 24 DGB3
GND 34 34 7 7 GND DGB4 25 25 DGB4
CP 35 35 6 6 CP DGB5 26 26 DGB5
GND 36 36 5 5 GND DGB6 27 27 DGB6
CCDCLK2 37 37 4 4 CCDCLK2 DGB7 28 28 DGB7
GND 38 38 3 3 GND GND 29 29 GND
CCDCLK1 39 39 2 2 CCDCLK1 DBB0 30 30 DBB0
GND 40 40 1 1 GND DBB1 31 31 DBB1
DBB2 32 32 DBB2
DBB3 33 33 DBB3
YC1 YC11 DBB4 34 34 DBB4
+5.1V 6 6 1 1 +5.1V DBB5 35 35 DBB5
GND 5 5 2 2 GND DBB6 36 36 DBB6 DPRPWB
+10V 4 4 3 3 +10V DBB7 37 37 DBB7 YC1
GND 3 3 4 4 GND HHALF 38 38 HHALF GND 1 1 1 1 GND
+3.3V 2 2 5 5 +3.3V SLEEP 39 39 SLEEP A+ 2 2 2 2 TXP
GND 1 1 6 6 GND TWS_DET 40 40 TWS_DET A- 3 3 3 3 TXN
GND 41 41 GND GND 4 4 4 4 GND
LA2 42 42 LA2 B- 5 5 5 5 RXN
LA3 43 43 LA3 B+ 6 6 6 6 RXP
LA4 44 44 LA4 GND 7 7 7 7 GND
LA5 45 45 LA5
LA6 46 46 LA6
LA7 47 47 LA7
YC13 LA8 48 48 LA8
GND 3 3 1 1 +5.1V LA9 49 49 LA9 3.3V 1 1
OSS ORGSW 2 2 2 2 ORG_SW LA10 50 50 LA10 3.3V 2 2
5V 1 1 3 3 GND LA11 51 51 LA11 3.3V 3 3
LA12 52 52 LA12 GND 4 4
LA13 53 53 LA13 GND 5 5
LA14 54 54 LA14 GND 6 6 YC27
LA15 55 55 LA15 5V 7 7 3 3 GND
LA16 56 56 LA16 5V 8 8 2 2 +5V_HDD
YC6 LA17 57 57 LA17 5V 9 9 1 1 GND
11 11 11 11 +24V1 GND 58 58 GND GND 10 10
10 10 10 10 +24V1 LD0 59 59 LD0 ACT 11 11
9 9 9 9 POW LD1 60 60 LD1 GND 12 12
8 8 8 8 PWM LD2 61 61 LD2 12V 13 13
7 7 7 7 PGND LD3 62 62 LD3 12V 14 14
6 6 6 6 63 63 12V
LEDPWB 5 5 5 5
SGND
VSET
LD4
LD5 64 64
LD4
LD5
15 15
4 4 4 4 SCL
ISCPWB LD6 65 65 LD6
3 3 3 3 SDA LD7 66 66 LD7 HDD1
2 2 2 2 FAIL GND 67 67 GND
1 1 1 1 +5V INT 68 68 INT
RESETZ 69 69 RESETZ
GND 70 70 GND
YC14 CEZ 71 71 CEZ YC2
3.3V 3 3 1 1 +3.3V WEZ 72 72 WEZ GND 1 1
ODSW GND
COSW
2
1
2
1
2
3
2
3
GND
CO_SW
OEZ
SCLKIN
73
74
73
74
OEZ
SCLKIN
HTPDN
LOCKN
2
3
2
3
3.3V 75 75 3.3V GND 4 4 To DPDPWB
3.3V 76 76 3.3V RX0N 5 5
YC8 3.3V 77 77 3.3V RX0P 6 6
3.3V 3 3 4 4 +3.3V 3.3V 78 78 3.3V GND 7 7
HPS GND 2 2 5 5 GND GND 79 79 GND
HPSW 1 1 6 6 HP_SW GND 80 80 GND
YC5
A 4 1 SMOT AP
B 3 2 SMOT BP
SM A/ 2 3 SMOT AN
B/ 1 4 SMOT BN
YC7
+24V1
GND
1
2
1
2
1
2
PSPWB
YC12 GND 3 3 From PSPWB YC14 YC24
16 16 24V2 GND 4 4 4 12V1 8 8 1 1 +12V
15 15 24V2 +24V1_2 5 5 5 12V1 7 7 2 2 +12V
14 14 24V2 +24V1_2 6 6 12V1 6 6 3 3 +12V
13 13 Reserve 12V1 5 5 4 4 +12V
12 12 GND GND 4 4 5 5 GND
11 11 GND GND 3 3 6 6 GND
10 10 GND GND 2 2 7 7 GND
9 9 Reserve GND 1 1 8 8 GND
8 8 DP_OPEN
7 7 DP_SI
6 6 DP_SO
DPMPWB 5 5 DP_CLK
4 4 DP_SEL
(option) 3 3 DP_RDY
2 2 DP_TMG
1 1 GND(SPARE)
1
2
3
4 From DPRPWB
5
6
7
2-4-28
2LK/2LN/2LM/2LC
YC2 YC9
GND(AFE_SHP) 1 1 40 40 GND(AFE_SHP) MPWB
CLPIN 2 2 39 39 CLPIN
GND(AFE_SHD) 3 3 38 38 GND(AFE_SHD) YC4 YC25
MCLK 4 4 37 37 AFE_MCLK GND 1 1 1 1 GND
GND 5 5 36 36 GND HTPDN 2 2 2 2 HTPDN
CCDSEL 6 6 35 35 CCDSEL LOCKN 3 3 3 3 LOCKN YC2
GND 7 7 34 34 GND GND 4 4 4 4 GND GND 1 1 1 1 GND
TXCLK1P 8 8 33 33 DIS_CISCKN TX0N 5 5 5 5 TX0N A+ 2 2 2 2 TXP
TXCLK1N 9 9 32 32 DIS_CISCKP TX0P 6 6 6 6 TX0P
YC10 YC4 A- 3 3 3 3 TXN
GND 10 10 31 31 GND GND 7 7 7 7 GND GND 1 1 GND GND 4 4 4 4 GND
TXOUTC1P 11 11 30 30 DIS_CIS_5N GND 2 2 GND B- 5 5 5 5 RXN
TXOUTC1N 12 12 29 29 DIS_CIS_5P 3.3V 3 3 3.3V B+ 6 6 6 6 RXP
GND 13 13 28 28 GND 3.3V 4 4 3.3V GND 7 7 7 7 GND
TXOUTB1P 14 14 27 27 DIS_CIS_4N 3.3V 5 5 3.3V
TXOUTB1N 15 15 26 26 DIS_CIS_4P 3.3V 6 6 3.3V
GND 16 16 25 25 GND VCLKB 7 7 VCLKB
TXOUTC2P 17 17 24 24 DIS_CIS_3N VSYNCB 8 8 VSYNCB
TXOUTC2N 18 18 23 23 DIS_CIS_3P HSYNCB 9 9 HSYNCB 3.3V 1 1
GND 19 19 22 22 GND MREB 10 10 MREB 3.3V 2 2
TXOUTB2P 20 20 21 21 DIS_CIS_2N GND 11 11 GND 3.3V 3 3
TXOUTB2N 21 21 20 20 DIS_CIS_2P YC3 YC11 DRB0 12 12 DRB0 GND 4 4
GND 22 22 19 19 GND SC_CLK 1 1 8 8 SC_CLK DRB1 13 13 DRB1 GND 5 5
CCDPWB TXOUTA2P 23 23 18 18 DIS_CIS_1N SC_SO 2 2 7 7 SC_SO DRB2 14 14 DRB2 GND 6 6 YC32
TXOUTA2N 24 24 17 17 DIS_CIS_1P SC_SI 3 3 6 6 SC_SI DRB3 15 15 DRB3 5V 7 7 3 3 GND
GND 25 25 16 16 GND SC_BSY 4 4 5 5 SC_BSY DRB4 16 16 DRB4 5V 8 8 2 2 +5V_HDD
SCLK 26 26 15 15 AFECLK SC_HLDN 5 5 4 4 SC_HLDN DRB5 17 17 DRB5 5V 9 9 1 1 GND
SDI 27 27 14 14 AFE_SO SC_DIR 6 6 3 3 SC_DIR DRB6 18 18 DRB6 GND 10 10
SENB 28 28 13 13 AFE_EN SC_IRN 7 7 2 2 SC_IRN DRB7 19 19 DRB7 ACT 11 11
SDO 29 29 12 12 AFE_SI GND(SPARE) 8 8 1 1 GND(SPARE) GND 20 20 GND GND 12 12
SH 30 30 11 11 SH DGB0 21 21 DGB0 12V 13 13
TG 31 31 10 10 TG DGB1 22 22 DGB1 12V 14 14
GND 32 32 9 9 GND(Mono/Color) DGB2 23 23 DGB2 12V 15 15
RS 33 33 8 8 RS DGB3 24 24 DGB3
GND 34 34 7 7 GND DGB4 25 25 DGB4
CP 35 35 6 6 CP DGB5 26 26 DGB5 HDD2
GND 36 36 5 5 GND DGB6 27 27 DGB6
CCDCLK2 37 37 4 4 CCDCLK2 DGB7 28 28 DGB7
GND 38 38 3 3 GND GND 29 29 GND
CCDCLK1 39 39 2 2 CCDCLK1 DBB0 30 30 DBB0
GND 40 40 1 1 GND DBB1 31 31 DBB1
DBB2 32 32 DBB2
DBB3 33 33 DBB3
YC1 YC11 DBB4 34 34 DBB4
+5.1V 6 6 1 1 +5.1V DBB5 35 35 DBB5
GND 5 5 2 2 GND DBB6 36 36 DBB6 DPRPWB
+10V 4 4 3 3 +10V DBB7 37 37 DBB7 YC1
GND 3 3 4 4 GND HHALF 38 38 HHALF GND 1 1 1 1 GND
+3.3V 2 2 5 5 +3.3V SLEEP 39 39 SLEEP A+ 2 2 2 2 TXP
GND 1 1 6 6 GND TWS_DET 40 40 TWS_DET A- 3 3 3 3 TXN
GND 41 41 GND GND 4 4 4 4 GND
LA2 42 42 LA2 B- 5 5 5 5 RXN
LA3 43 43 LA3 B+ 6 6 6 6 RXP
LA4 44 44 LA4 GND 7 7 7 7 GND
LA5 45 45 LA5
LA6 46 46 LA6
LA7 47 47 LA7
YC13 LA8 48 48 LA8
GND 3 3 1 1 +5.1V LA9 49 49 LA9 3.3V 1 1
OSS ORGSW 2 2 2 2 ORG_SW LA10 50 50 LA10 3.3V 2 2
5V 1 1 3 3 GND LA11 51 51 LA11 3.3V 3 3
LA12 52 52 LA12 GND 4 4
LA13 53 53 LA13 GND 5 5
LA14 54 54 LA14 GND 6 6 YC27
LA15 55 55 LA15 5V 7 7 3 3 GND
LA16 56 56 LA16 5V 8 8 2 2 +5V_HDD
YC6 LA17 57 57 LA17 5V 9 9 1 1 GND
11 11 11 11 +24V1 GND 58 58 GND GND 10 10
10 10 10 10 +24V1 LD0 59 59 LD0 ACT 11 11
9 9 9 9 POW LD1 60 60 LD1 GND 12 12
8 8 8 8 PWM LD2 61 61 LD2 12V 13 13
7 7 7 7 PGND LD3 62 62 LD3 12V 14 14
6 6 6 6 63 63 12V
LEDPWB 5 5 5 5
SGND
VSET
LD4
LD5 64 64
LD4
LD5
15 15
4 4 4 4 SCL
ISCPWB LD6 65 65 LD6
3 3 3 3 SDA LD7 66 66 LD7 HDD1
2 2 2 2 FAIL GND 67 67 GND
1 1 1 1 +5V INT 68 68 INT
RESETZ 69 69 RESETZ
GND 70 70 GND
YC14 CEZ 71 71 CEZ YC2
3.3V 3 3 1 1 +3.3V WEZ 72 72 WEZ GND 1 1
ODSW GND
COSW
2
1
2
1
2
3
2
3
GND
CO_SW
OEZ
SCLKIN
73
74
73
74
OEZ
SCLKIN
HTPDN
LOCKN
2
3
2
3
3.3V 75 75 3.3V GND 4 4 To DPDPWB
3.3V 76 76 3.3V RX0N 5 5
YC8 3.3V 77 77 3.3V RX0P 6 6
3.3V 3 3 4 4 +3.3V 3.3V 78 78 3.3V GND 7 7
HPS GND 2 2 5 5 GND GND 79 79 GND
HPSW 1 1 6 6 HP_SW GND 80 80 GND
YC5
A 4 1 SMOT AP
B 3 2 SMOT BP
SM A/ 2 3 SMOT AN
B/ 1 4 SMOT BN
YC7
+24V1
GND
1
2
1
2
1
2
PSPWB
YC12 GND 3 3 From PSPWB YC14 YC24
16 16 24V2 GND 4 4 4 12V1 8 8 1 1 +12V
15 15 24V2 +24V1_2 5 5 5 12V1 7 7 2 2 +12V
14 14 24V2 +24V1_2 6 6 12V1 6 6 3 3 +12V
13 13 Reserve 12V1 5 5 4 4 +12V
12 12 GND GND 4 4 5 5 GND
11 11 GND GND 3 3 6 6 GND
10 10 GND GND 2 2 7 7 GND
9 9 Reserve GND 1 1 8 8 GND
8 8 DP_OPEN
7 7 DP_SI
6 6 DP_SO
DPMPWB 5 5 DP_CLK
4 4 DP_SEL
(option) 3 3 DP_RDY
2 2 DP_TMG
1 1 GND(SPARE)
1
2
3
4 From DPRPWB
5
6
7
2-4-29
2LK/2LN/2LM/2LC
CN1 YC4
SGND 1 1 1 1 SGND YC7 CN1 CN2
SGND 2 2 2 2 SGND KMDET 1 1 1 12 KMDET FG 1 1 1 1 FG
CK 3 3 3 3 CK NC 2 2 2 11 NC PHS TXD 2 2 3 3 TXD
SGND 4 4 4 4 SGND KMDREQ 3 3 3 10 KMDREQ SGND 3 3 13 13 SGND
SGND 5 5 5 5 SGND KMACK 4 4 4 9 KMACK PHS DTR 4 4 16 16 DTR
SC 6 6 6 6 SC KMRXD 5 5 5 8 KMRXD 5V OUT 5 5 18 18 5V
R0(LSB) 7 7 7 7 R0(LSB) SGND 6 6 6 7 SGND PHS RTS 6 6 7 7 RTS
R1 8 8 8 8 R1 KMTXD 7 7 7 6 KMTXD N.C. 7 7
R2 9 9 9 9 R2 SGND 8 8 8 5 SGND PHS DCD 8 8 15 15 DCD
SGND 10 10 10 10 SGND SGND 9 9 9 4 SGND N.C. 9 9
R3 11 11 11 11 R3 SGND 10 10 10 3 SGND PHS RXD 10 10 5 5 RXD
R4 12 12 12 12 R4 +5V 11 11 11 2 +5V SGND 11 11 19 19 SGND
R5(MSB) 13 13 13 13 R5(MSB) +5V 12 12 12 1 +5V PHS DSR 12 12 11 11 DSR KMAS
SGND 14 14 14 14 SGND PHS RI 13 13 14 14 RI
G0(LSB) 15 15 15 15 G0(LSB) PHS CTS 14 14 9 9 CTS
G1 16 16 16 16 G1 2 2 NC
G2 17 17 17 17 G2 4 4 NC
CN3
KMASPWB
SGND 18 18 18 18 SGND 6 6 NC
G3 19 19 19 19 G3 GND 1 8 8 NC
G4 20 20 20 20 G4 TXD 2 10 10 NC
G5(MSB) 21 21 21 21 G5(MSB) DTR 3 12 12 NC
SGND 22 22 22 22 SGND RTS 4 17 17 NC
B0(LSB) 23 23 23 23 B0(LSB) DCD 5 20 20 NC
B1 24 24 24 24 B1 RXD 6
B2 25 25 25 25 B2 DSR 7
SGND 26 26 26 26 SGND CTS 8
B3 27 27 27 27 B3 YC11 RI 9 KMAS
B4 28 28 28 28 B4 1 1 2 1 + YC5 NC 10
B5(MSB) 29 29 29 29 B5(MSB)
VO2
VO1 2 2 1
Relay
2 - Speaker TD1+ 1
(option)
SGND 30 30 30 30 SGND TD1- 2
H_SYNC 31 31 31 31 H_SYNC TD2+ 3
SGND 32 32 32 32 SGND TD2- 4
V_SYNC 33 33 33 33 V_SYNC CT1 5
SGND 34 34 34 34 SGND CT2 6
ENB 35 35 35 35 ENB TD3+ 7
CM 36 36 36 36 CM YC1 YC30 TD3- 8
3.3V 37 37 37 37 3.3V +5V 1 6 6 1 6 1 +5V TD4+ 9 Ethernet
3.3V 38 38 38 38 3.3V +5V 2 5 5 2 5 2 +5V TD4- 10
3.3V 39 39 39 39 3.3V +5V 3 4 4 3 4 3 +5V GRLED_A1 11
Relay
3.3V 40 40 40 40 3.3V GND 4 3 3 4 3 4 GND GRLED_K1 12
GND 5 2 2 5 2 5 GND YWLED_A2 13
GND 6 1 1 6 1 6 GND YWLED_K2 14
LCD YC16
YC3 YC12 GND 1
SGND 15 15 13 1 13 13 SGND D3 2
PANEL_STATUS 14 14 12 2 12 12 PANEL_STATUS D4 3
INT_POWERKEY_N 13 13 11 3 11 11 INT_POWERKEY_N D5 4
PANEL RESET 12 12 10 4 10 10 PANEL RESET D6 5
AUDIO 11 11 9 5 9 9 AUDIO D7 6
LIGHTOFF_POWERON 10 10 8 6 8 8 LIGHTOFF_POWERON /CE1 7
SHUT_DOWN 9 9 7 Relay 7 7 7 SHUT_DOWN A10 8
LED_PROCESSING_N 8 8 6 8 6 6 LED_PROCESSING_N /OE 9
YC14 LED_ATTENTION_N 7 7 5 9 5 5 LED_ATTENTION_N A9 10
1 1 LED_A LED_MEMORY_N 6 6 4 10 4 4 LED_MEMORY_N A8 11
2 2 NC SUPND_POWER 5 5 3 11 3 3 SUPND_POWER A7 12
3 3 LED_C ENERGY_SAVE 4 4 2 12 2 2 ENERGY_SAVE VCC 13
4 4 NC DEEP_POWERON 3 3 1 13 1 1 DEEP_POWERON A6 14
SECOND_TRAY_SW 2 2 YC20 A5 15
GND 1 1 VBUS 1 A4 16
YC5 DATA- 2 A3 17
TOP 1 1 BOT Y- DATA+ 3 A2 18
Touch panel LEFT 2 2 LEFT X+ GND 4 Type A+B A1 19
BOTTOM 3 3 TOP Y+ LockPin1 LP1 A0 20
RIGHT 4 4 RIGHT X- LockPin2 LP2 D0 21
LockPin3 LP3 D1 22
LockPin4 LP4 D2 23
WP 24
/CD2 25
/CD1 26
YC23 D11 27 CF card
D12 28
YC1 YC7 YC2 YC17 +12V 1 2 D13 29
SCAN4 12 12 1 1 SCAN4 VBUS 1 1 1 1 VBUS GND 2 1 CONFM D14 30
KEY5 11 11 2 2 KEY5 DN 2 2 2 2 DATA - D15 31
KEY6 10 10 3 3 KEY6 DP 3 3 3 3 DATA + /CE2 32
KEY7 9 9 4 4 KEY7 ID 4 4 4 4 NC /VS1 33
SCAN0 8 8 5 5 SCAN0 GND 5 5 5 5 GND /IORD 34
SCAN1 7 7 6 6 SCAN1 LockPin(1) LP-1 LP_1 LockPin(1) YC31 /IOWD 35
SCAN2 6 6 7 7 SCAN2 LockPin(2) LP-2 LP_2 LockPin(2) CD/DAT3 1 /WE 36
SCAN3 5 5 8 8 SCAN3 LockPin(3) LP-3 LP_3 LockPin(3) CMD 2 RDY/BSY 37
LED2 4 4 9 9 LED2 LockPin(4) LP-4 VSS 3 VCC 38
LED3 3 3 10 10 LED3 VDD 4 CSEL 39
LED4 2 2 11 11 LED4 CLK 5 VS2 40
GND 1 1 12 12 GND VSS 6 RESET 41
YC21 DAT0 7 /WAIT 42
VBUS 1 1 1 VBUS DAT1 8 INPACK 43
DATA - 2 2 2 DATA- DAT2 9 /REG 44
USB host DATA + 3 3 3 DATA+ CD 10
SD card BVD2 45
YC1 YC6 4 4 NC COMMON 11 BVD1 46
KEY4 1 1 1 1 KEY4 GND 4 5 5 GND WP 12 D8 47
SCAN2 2 2 2 2 SCAN2 LP1 LockPin1 LockPin(1) 13 D9 48
INT_POWERKEY_N 3 3 3 3 INT_POWERKEY_N LP2 LockPin2 LockPin(2) 14 D10 49
SCAN1 4 4 4 4 SCAN1 LP3 LockPin3 LockPin(3) 15 GND 50
LED1 5 5 5 5 LED1 LockPin(4) 16 Lock Pin(1) 51
SUPND_POWER 6 6 6 6 SUPND_POWER Lock Pin(2) 52
KEY3 7 7 7 7 KEY3
KEY2 8 8 8 8 KEY2 OPWB3
KEY1 9 9 9 9 KEY1
LED0 10 10 10 10 LED0
KEY0 11 11 11 11 KEY0 YC8 YC1 MPWB
SCAN4 12 12 12 12 SCAN4 PROCESSING_LED 1 1 4 4 PROCESSING_LED
SCAN3 13 13 13 13 SCAN3 MEMORY LED 2 2 3 3 MEMORY LED
SCAN0 14 14 14 14 SCAN0 ATTENTION_LED 3 3 2 2 ATTENTION_LED
GND 15 15 15 15 GND GND 4 4 1 1 GND
16 16 GND
17 17 GND
18 18 GND
OPWB2 19 19 GND
20 20 GND
OPWB1
2-4-30
2LK/2LN/2LM/2LC
YC2 FCPWB
VBUS1 20 20 VBUS
YC8 YC3 USB_DN1 19 19 USB_DN
VBUS1 15 15 1 1 VBUS1 USB_DP1 18 18 USB_DP
USB_DN1 14 14 2 2 USB_DN1 GND 17 17 GND
USB_DP1 13 13 3 3 USB_DP1 NC 16 16 NC
GND 12 12 4 4 GND NC 15 15 NC
AUDIO1 11 11 5 5 AUDIO1 GND 14 14 GND
WAKEUP1 10 10 6 6 WAKEUP1 NC 13 13 NC
RESET1 9 9 7 7 RESET1 NC 12 12 NC
GND 8 8 8 8 GND GND 11 11 GND
VBUS0 7 7 9 9 VBUS0 NC 10 10 NC
USB_DN0 6 6 10 10 USB_DN0 NC 9 9 NC
USB_DP0 5 5 11 11 USB_DP0 NC 8 8 NC
GND 4 4 12 12 GND AUDIO1 7 7 AUDIO
AUDIO0 3 3 13 13 AUDIO0 WAKEUP 6 6 WAKEUP
WAKEUP0 2 2 14 14 WAKEUP0 GND 5 5 GND
RESET0 1 1 15 15 RESET0 VDD5_CUT1 4 4 VDD5_CUT
RESETN1 3 3 RESETN
GND 2 2 GND
VDD5 1 1 VDD5
YC9 YC4
5V_CUT1 6 1 6 1 5V_CUT1
GND 5 2 5 2 GND
5V 4 3 4 3 5V
GND 3 4 3 4 GND YC1 FCPWB
5V_CUT0 2 5 2 5 5V_CUT0 VBUS0 20 20 VBUS
GND 1 6 1 6 GND USB_DN0 19 19 USB_DN
USB_DP0 18 18 USB_DP
GND 17 17 GND
NC 16 16 NC
NC 15 15 NC
GND 14 14 GND
NC 13 13 NC
NC 12 12 NC
GND 11 11 GND
NC 10 10 NC
NC 9 9 NC
IFPWB NC 8 8 NC
AUDIO0 7 7 AUDIO
WAKEUP0 6 6 WAKEUP
GND 5 5 GND
MPWB VDD5_CUT0 4 4 VDD5_CUT
RESETN0 3 3 RESETN
GND 2 2 GND
VDD5 1 1 VDD5
YC9 YC2
12V 10 10 1 1 12V
12V 9 9 2 2 12V
SGND 8 8 3 3 SGND
SGND 7 7 4 4 SGND
SDI 6 6 5 5 SDI
SDICLK 5 5 6 6 SDICLK FIRPWB
SGND 4 4 7 7 SGND
SDO 3 3 8 8 SDO
SDOCLK 2 2 9 9 SDOCLK
SGND 1 1 10 10 SGND
YC3 YC46 YC47 YC4 YC3

HSYNC_AN 1 1 1 1 HSYNC_AN HSYNC_AN 1 1 1 1 HSYNC_AN HSYNC_AN 1 1
HSYNC_AP 2 2 2 2 HSYNC_AP HSYNC_AP 2 2 2 2 HSYNC_AP HSYNC_AP 2 2
HSYNC_BN 3 3 3 3 HSYNC_BN HSYNC_BN 3 3 3 3 HSYNC_BN HSYNC_BN 3 3
HSYNC_BP 4 4 4 4 HSYNC_BP HSYNC_BP 4 4 4 4 HSYNC_BP HSYNC_BP 4 4
HSYNC_CN 5 5 5 5 HSYNC_CN HSYNC_CN 5 5 5 5 HSYNC_CN HSYNC_CN 5 5
HSYNC_CP 6 6 6 6 HSYNC_CP HSYNC_CP 6 6 6 6 HSYNC_CP HSYNC_CP 6 6
HSYNC_DN 7 7 7 7 HSYNC_DN HSYNC_DN 7 7 7 7 HSYNC_DN HSYNC_DN 7 7
HSYNC_DP 8 8 8 8 HSYNC_DP HSYNC_DP 8 8 8 8 HSYNC_DP HSYNC_DP 8 8
VSYNC_AN 9 9 9 9 VSYNC_AN VSYNC_AN 9 9 9 9 VSYNC_AN VSYNC_AN 9 9
VSYNC_AP 10 10 10 10 VSYNC_AP VSYNC_AP 10 10 10 10 VSYNC_AP VSYNC_AP 10 10
VSYNC_BN 11 11 11 11 VSYNC_BN VSYNC_BN 11 11 11 11 VSYNC_BN VSYNC_BN 11 11 FIERY CONTROLLER
VSYNC_BP 12 12 12 12 VSYNC_BP VSYNC_BP 12 12 12 12 VSYNC_BP VSYNC_BP 12 12
VSYNC_CN 13 13 13 13 VSYNC_CN VSYNC_CN 13 13 13 13 VSYNC_CN VSYNC_CN 13 13
VSYNC_CP 14 14 14 14 VSYNC_CP VSYNC_CP 14 14 14 14 VSYNC_CP VSYNC_CP 14 14
VSYNC_DN 15 15 15 15 VSYNC_DN VSYNC_DN 15 15 15 15 VSYNC_DN VSYNC_DN 15 15
VSYNC_DP 16 16 16 16 VSYNC_DP VSYNC_DP 16 16 16 16 VSYNC_DP VSYNC_DP 16 16
SGND 17 17 17 17 SGND SGND 17 17 17 17 SGND SGND 17 17
TCLKP 18 18 18 18 TCLKP VCLK_P 18 18 18 18 VCLK_P TCLKP 18 18
TCLKN 19 19 19 19 TCLKN VCLK_N 19 19 19 19 VCLK_N TCLKN 19 19
TCP 21 21 21 21 TCP CH3_P 21 21 21 21 CH3_P TCP 21 21
TCN 22 22 22 22 TCN CH3_N 22 22 22 22 CH3_N TCN 22 22
TBP 24 24 24 24 TBP CH2_P 24 24 24 24 CH2_P TBP 24 24
TBN 25 25 25 25 TBN CH2_N 25 25 25 25 CH2_N
SGND 26 26 26 26 SGND SGND 26 26 26 26 SGND
TAP 27 27 27 27 TAP CH1_P 27 27 27 27 CH1_P
TAN 28 28 28 28 TAN CH1_N 28 28 28 28 CH1_N
SGND 29 29 29 29 SGND NC 29 29 29 29 NC
SLEEP 30 30 30 30 SLEEP NC 30 30 30 30 NC
HLD_ENG 31 31 31 31 HLD_ENG NC 31 31 31 31 NC
NC 32 32 32 32 NC NC 32 32 32 32 NC
SGND 33 33 33 33 SGND NC 33 33 33 33 NC
EG IRN 34 34 34 34 EG IRN NC 34 34 34 34 NC
EG SO 35 35 35 35 EG SO NC 35 35 35 35 NC
EG SBSY 36 36 36 36 EG SBSY NC 36 36 36 36 NC
EG SDIR 37 37 37 37 EG SDIR NC 37 37 37 37 NC
EG_SI 38 38 38 38 EG_SI NC 38 38 38 38 NC
EG_SCLK 39 39 39 39 EG_SCLK NC 39 39 39 39 NC
SGND 40 40 40 40 SGND NC 40 40 40 40 NC
EPWB
YC5
TRP1+ 1 1
TRP1- 2 2
TRP2+ 3 3
TRP2- 4 4
TRP3+ 5 5
TRP3- 6 6
TRP4+ 7 7
TRP4- 8 8
2-4-31
1-1 INSTALLATION GUIDE
INSTALLATION GUIDE FOR

DOCUMENT PROCESSOR
D F
B
C C*
E
M N
K*
K** J
A L
H
C*. Fixing fitting (width: 45 mm)*1 .............................. 1 J. M3 × 8 screw BLACK*1 ......................................... 1

English
D. Angle control fitting............................................... 1 K. Label “Operation procedure” ..................................
Supplied parts E. DP cable cover..................................................... 1 *: for metric specification
A. DP ........................................................................ 1 F. Pin ........................................................................ 1 **: for inch specification
B. Original mat.......................................................... 1 G. M4 × 14TP screw ................................................. 8 L. Caution label “Original face up!”...........................1
C. Fixing fitting (width: 38.5 mm) ...............2 (DP-770) H. Left hinge cover*1 .................................................. 1 M. DP relay PWB*1 .................................................... 1
1 (DP-771) I. Right hinge cover*1 ............................................... 1 N. M3 × 8 screw*1 ...................................................... 2
*1: DP-771 only
C.*Fixation (largeur: 45 mm)*1 ................................... 1 K. Étiquette relative à la procédure d’utilisation........ 1

Français
D. Fixation d’angle .................................................... 1 * : pour des spécifications métriques
Pièces fournies E. Couvercle du câble du DP ................................... 1 ** : pour des spécifications anglo-saxonnes
A. DP ........................................................................ 1 F. Goupille ................................................................ 1 L. Étiquette d’avertissement relative à l’orientation
B. Plaque d’original .................................................. 1 G. Vis TP M4 × 14..................................................... 8 vers le haut de la face de l’original ......................1
C. Fixation (largeur: 38,5 mm)....................... 2 (DP-770) H. Couvercle de charnière gauche*1 ......................... 1 M. Carte de circuit imprimé relais du DP*1 .................1
1 (DP-771) I. Couvercle de charnière droite*1 ............................ 1 N. Vis M3 × 8*1 ......................................................... 2
J. Vis M3 × 8 NOIRE*1 .............................................. 1 *1: DP-771 uniquement
C*.Herraje de fijación (anchura: 45 mm)*1 ................. 1 J. Tornillo M3 × 8 NEGRO*1 ......................................1

Español
D. Herraje de control de ángulo................................ 1 K. Etiqueta “Procedimiento operativo” ..................... 1
Partes suministradas E. Cubierta del cable del DP..................................... 1 *: para especificaciones en el sistema métrico
A. DP ........................................................................ 1 F. Pasador................................................................ 1 **: para especificaciones en el sistema de pulgadas
B. Alfombrilla para originales.................................... 1 G. Tornillo TP M4 × 14 .............................................. 8 L. Etiqueta de precaución “Original cara arriba” ......1
C. Herraje de fijación (anchura: 38,5 mm)....2 (DP-770) H. Cubierta de la bisagra izquierda*1 ........................ 1 M. PWB del relé del DP*1...........................................1
1 (DP-771) I. Cubierta de la bisagra derecha*1 .......................... 1 N. Tornillo M3 × 8*1 .................................................... 2
*1: DP-771 solamente
C*.Befestigungshalterung (Breite: 45 mm)*1.............. 1 J. M3 × 8 Schraube SCHWARZ*1 ............................. 1

Deutsch
D. Winkeleinstellbefestigung..................................... 1 K. Schild “Funktionsanweisung” ..............................1
Gelieferte Teile E. DP-Kabelabdeckung ............................................ 1 *: für metrische Angaben
A. DP ........................................................................ 1 F. Stift ....................................................................... 1 **: für Angaben in Zoll
B. Originalmatte........................................................ 1 G. M4 × 14TP Schraube ........................................... 8 L. Warnschild “Originalschriftseite nach oben” ........ 1
C. Befestigungshalterung (Breite: 38,5 mm) .....2 (DP-770) H. Linke Scharnierabdeckung*1................................. 1 M. DP-Relaisleiterplatte *1.......................................... 1
.......................................................................1 (DP-771) I. Rechte Scharnierabdeckung*1 .............................. 1 N. M3 × 8*1 ................................................................2
*1: nur DP-771
C*. Accessorio di fissaggio (larghezza: 45 mm)*1 ...... 1 J. Vite M3 × 8 NERA*1 .............................................. 1

Italiano
D. Accessorio di regolazione angolare ..................... 1 K. Etichetta “Procedura di funzionamento” ..............1
Parti di fornitura E. Coperchio del cavo DP ........................................ 1 *: per specifiche in unità del sistema metrico
A. DP ........................................................................ 1 F. Perno.................................................................... 1 **: per specifiche in pollici
B. Tappetino originale ............................................... 1 G. Vite M4 × 14TP .................................................... 8 L. Etichetta di avvertimento “Originale rivolto verso l’alto!” ... 1
C. Accessorio di fissaggio (larghezza: 38,5 mm).... 2 (DP-770) H. Coperchio cerniera sinistra*1 ................................ 1 M. Scheda a circuiti stampati di comunicazione DP*1 ...1
1 (DP-771) I. Coperchio cerniera destra*1 .................................. 1 N. Vite M3 × 8*1 ........................................................2
*1: Solo DP-771
简体中文 C*.固定附件 ( 宽 45mm) *1 ..................1 I. 右部铰链盖板 *1 ........................1

D. 角度控制附件 .........................1 J. M3×8 螺丝 BLACK*1 .....................1
附属品 E. DP 电缆盖板 .......................... 1 M. DP 中继板 *1 ...........................1
A. DP................................... 1 F. 销 ...................................1 N. M3×8 螺 *1 ............................2
B. 原稿垫............................... 1 G. M4×14TP 螺钉 .........................8 *1: 仅限 DP-771
C. 固定附件 ( 宽 38.5mm) ......... 2(DP-770) H. 左部铰链盖板 *1 ........................1 (K) 和 (L) 并非附属品。
1(DP-771)
한국어 C*.고정쇠 (45mm 폭 ) *1 ................................1 I. 힌지커버 우 *1 ......................................... 1

D. 각도규제쇠 ............................................ 1 J. 나사 M3×8BLACK*1 ................................ 1
동봉품 E. DP 케이블커버 ....................................... 1 M. DP 중계기판 *1 ....................................... 1
A. DP 본체................................................. 1 F. 핀 ........................................................ 1 N. 나사 M3×8*1 .......................................... 2
B. 원고매트................................................ 1 G. 나사 M4×14TP ...................................... 8 *1: DP-771 만
C. 고정쇠 (38.5mm 폭 ) ...................2(DP-770) H. 힌지커버 좌 *1 ..........................................1 （K）（L）는 동봉되어 있지 않습니다 .
1(DP-771)
日本語 C*.固定金具 (45mm 幅 )*1 ...................1 J. ビス M3×8BLACK*1 ......................1

D. 角度規制金具 ........................ 1 M. DP 中継基板 *1 ........................ 1
同梱品 E. DP ケーブルカバー .................... 1 N. ビス M3×8*1 .......................... 2
A. DP 本体 ............................. 1 F. ピン ................................ 1
B. 原稿マット........................... 1 G. ビス M4×14TP ........................ 8 *1:DP-771 のみ
C. 固定金具 (38.5mm 幅 ) ......... 2(DP-770) H. ヒンジカバー左 *1 ......................1 (K)(L) は、同梱されていない。
1(DP-771) I. ヒンジカバー右 *1 ......................1
1
G
C
G
C
Precautions Procedure Attach the fixing fitting. (DP-770)

Be sure to remove any tape and/or cushioning When installing the DP, be sure to turn the MFP 1.Align projections (1) of each fixing fitting (C)
material from supplied parts. power off and disconnect the power plug from with holes (2) on the MFP and insert the fix-
The illustrations of the DP in the Installation the wall outlet. ing fittings (C) into the MFP.
Guide are for DP-771. 2.Secure each fixing fitting (C) with two M4 x
14TP screws (G).
Précautions Procédure Mettre en place la fixation. (DP-770)

Veillez à retirer les morceaux de bande adhé- Lors de l’installation du DP, veiller à mettre 1.Aligner les saillies (1) de chacune des
sive et/ou les matériaux de rembourrage des l’interrupteur du MFP hors tension et à pièces de fixation (C) avec les trous (2) sur
pièces fournies. débrancher la fiche d’alimentation de la prise le MFP et insérer ces pièces (C) dans le
Les schémas du DP dans le Guide d''installation murale. MFP.
concernent le DP-771. 2.Fixer chacune des pièces de fixation (C)
avec deux vis M4 x 14TP (G).
Precauciones Procedimiento Monte el herraje de fijación. (DP-770)

Asegúrese de despegar todas las cintas y/o Cuando instale el DP, asegúrese de apagar el 1.Alinee las salientes (1) de cada herraje de
material amortiguador de las partes suministra- interruptor principal del MFP y desenchúfelo del fijación (C) con los orificios (2) del MFP e
das. tomacorriente de la pared. inserte los herrajes de fijación (C) en el MFP.
Las ilustraciones del DP en la Guía de insta- 2.Asegure cada uno de los herrajes de fijación
lación corresponden al DP-771. (C) con dos tornillos M4 x 14TP (G).
Vorsichtsmaßnahmen Verfahren Anbringen der Befestigungshalterung. (DP-770)

Entfernen Sie Klebeband und/oder Dämpfungs- Schalten Sie vor Installation des DP unbedingt 1.Die Zapfen (1) jeder Befestigungshalterung
material vollständig von den mitgelieferten den MFP-Hauptschalter aus, und ziehen Sie (C) mit den Öffnungen (2) am MFP ausrich-
Teilen. den Netzstecker aus der Steckdose. ten und die Befestigungshalterungen (C) in
Die Abbildungen des DP in der den MFP einsetzen.
Installationsanleitung gelten für Modell DP-771. 2.Jede Befestigungshalterung (C) mit zwei M4
x 14TP Schrauben (G) befestigen.
Precauzioni Procedura Applicazione dell’accessorio di fissaggio. (DP-770)

Accertarsi di rimuovere tutti i nastri adesivi e/o il Spegnere l’interruttore principale e sfilare la 1.Allineare le sporgenze (1) di ogni accessorio
materiale di imbottitura dalle parti fornite. spina dell’MFP dalla presa prima di installare il di fissaggio (C) con i fori (2) sull’MFP, ed
Le illustrazioni del DP nella Guida DP. inserire gli accessori di fissaggio (C)
all’installazione sono per il modello DP-771. nell’MFP.
2.Bloccare ogni accessorio di fissaggio (C)
con le due viti M4 x 14TP (G).
注意事项安装步骤安装固定附件。（DP-770）

如果附属品上带有固定胶带，缓冲材料时务必揭安装 DP 时，请务必将 MFP 电源关闭，关拔下电源 1.将各固定附件（C）上的突出部分（1）与 MFP
下。插头再进行安装作业。上的孔（2）对齐，然后将固定附件（C）插入
安装手册中关于 DP 的图示以 DP-771 为例。 MFP 中。
2.用两颗 M4×14TP 螺钉（G）固定各固定附件
（C）。
주의사항 설치순서 고정쇠의 부착（DP-770）

동봉품에 고정 테이프 , 완충재가 붙어 있는 경 DP 본체를 설치할 때에는 반드시 MFP 본체의 1.고정쇠 (C) 의 돌기 (1) 와 MFP 본체의 구멍
우에는 반드시 제거할 것 . 주 전원 스위치를 OFF 로 하고 전원 플러그를 (2) 을 맞추고 MFP 본체에 고정쇠 (C) 를 꽂
설치순서에 기재되어 있는 DP 본체 일러스트는 뺀 다음 작업을 할 것 . 습니다 .
DP-771 입니다 . 2.나사 M4×14TP(G) 각 2 개로 2 개의 고정쇠
(C) 를 고정합니다 .
注意事項取付手順固定金具の取り付け（DP-770）

同梱品に固定テープ、緩衝材が付いている場合 DP 本体を設置するときは、必ず MFP 本体の主電 1.固定金具 (C) の突起 (1) と MFP 本体の穴
は必ず取り外すこと。源スイッチを OFF にし、電源プラグを抜いてか (2) を合わせ、 MFP 本体に固定金具 (C) を差
設置手順書に記載している DP 本体のイラストら作業すること。し込む。
は、
DP-771 です。 2.ビス M4×14TP(G) 各 2 本で 2 つの固定金具
(C) を固定する。
2
G
C*
G F
G
C G
C (C*)
A
2
C A
4
2
C (C*)
1 3
1 5
Attach the fixing fitting. (DP-771) Install the DP. 5.Install DP (A) onto the MFP securely with pin
1.Align the projections (1) on the right fixing fit- 3.Align hinge hole (3) of DP (A) with pin (4) of (F) and two M4 × 14TP screws (G).
ting (C) and on the wider left fixing fitting (C*) fixing fitting (C), place DP (A) on the MFP.
with the respective holes (2) in the MFP and 4.Slide the DP (A) toward the front side and
then insert the fixing fittings into the MFP. engage hinges into hooks (5) on fixing fit-
2.Secure each of the fixing fittings (C) (C*) tings (C).
with 2 M4 × 14TP screws (G).
Mettre en place la fixation. (DP-771) Installer le DP. 5.Installer le DP (A) sur le MFP en le fixant à
1.Aligner les saillies (1) de la fixation droite (C) 3.Aligner le trou de la charnière (3) du DP (A) l’aide de la goupille (F) et des deux vis TP
et de la fixation gauche plus large (C*) avec sur la goupille (4) de la fixation (C) et placer M4 × 14 (G).
les trous correspondants (2) du MFP et le DP (A) sur le MFP.
insérer les fixations dans le MFP. 4.Faire glisser le DP (A) vers l'avant et
2.Fixer chaque des fixations (C) (C*) avec 2 engager les charnières dans les crochets (5)
vis TP M4 × 14 (G). sur les pièces de fixation (C).
Monte el herraje de fijación. (DP-771) Instale el DP. 5.Instale el DP (A) firmemente en el MFP con
1. Alinee los salientes (1) del herraje de fijación dere- 3.Alinee el orificio de bisagra (3) del DP (A) el pasador (F) y dos tornillos TP M4 × 14 (G
cho (C) y del herraje de fijación izquierdo más con el pasador (4) del herraje de fijación (C)
ancho (C*) con los orificios correspondientes (2)
y coloque el DP (A) en el MFP.
del MFP y, después, inserte los herrajes de fijación
en el MFP. 4.Deslice el DP (A) hacia el frente y enganche
2. Asegure cada uno de los herrajes de fijación (C) las bisagras en los ganchos (5) de los her-
(C*) con 2 tornillos TP M4 × 14 (G). rajes de fijación (C).
Anbringen der Befestigungshalterung. (DP-771) Installieren des DP. 5.DP (A) sicher mit einem Stift (F) und zwei M4
1. Die Zapfen (1) an der rechten Befestigungshalter- 3.Scharnierloch (3) des DP (A) mit Stift (4) der × 14TP Schrauben (G) am MFP befestigen.
ung (C) und an der breiteren Befestigungshalter- Befestigungshalterung (C) ausrichten, und
ung (C*) mit den entsprechenden Öffnungen (2)
DP (A) auf den MFP stellen.
am MFP ausrichten und die Befestigungshalterun-
gen in den MFP einsetzen. 4.Den DP (A) nach vorne hin verschieben und
2. Die Befestigungshalterungen (C) (C*) mit den 2 M4 die Scharniere in die Haken (5) an den Bef-
× 14TP Schrauben (G) befestigen. estigungshalterungen (C) einsetzen.
Applicazione dell’accessorio di fissaggio. (DP-771) Montaggio del DP. 5.Montare il DP (A) sull’MFP assicurandolo
1. Allineare le sporgenze (1) sull'accessorio di fissag- 3.Allineare il foro della cerniera (3) del DP (A) con il perno (F) e due viti M4 × 14TP (G).
gio destro (C) e sull'accessorio di fissaggio sinistro con il perno (4) dell’accessorio di fissaggio
più largo (C*) con i rispettivi fori (2) nell'MFP, e (C), quindi posizionare il DP (A) sull’MFP.
quindi inserire gli accessori di fissaggio nell'MFP.
4.Far scorrere il DP (A) verso il lato anteriore
2. Fissare ciascuno degli accessori di fissaggio (C)
(C*) con 2 viti M4 × 14TP (G).
ed inserire le cerniere nei ganci (5) sugli
accessori di fissaggio (C).
安装固定附件。(DP-771) 安装 DP 5.用销（F）和两颗 M4×14TP 螺钉（G）将 DP

1.将固定附件 (C) 从右侧、宽幅固定夹具 (C*) 3.将 DP（A）的铰链孔（3）对准固定附件（C）的（A）安装到 MFP 上。
从左侧将各自的突出部分 (1) 与 MFP 主机的销（4），并将 DP（A）放在 MFP 上。
孔 (2) 对齐并插入到 MFP 主机中。 4.朝前侧滑动 DP（A），然后将铰链与固定附件
2.使用各 2 颗 M4×14 螺丝 TP(G) 来固定固定附（C）上的卡扣（5）相啮合。
件 (C) 与固定附件 (C*)
고정쇠의 부착（DP-771） DP 본체 부착 5.핀 (F) 1 개와 나사 M4×14TP(G) 2 개로 DP

1.우측에 고정쇠 (C), 좌측에 광폭 고정쇠 (C*) 3.DP 본체 (A) 의 힌지부 구멍 (3) 과 고정쇠 본체 (A) 를 MFP 본체에 고정합니다 .
각각의 돌기 (1) 와 MFP 본체 구멍 (2) 을 맞 (C) 핀 (4) 을 맞추고 MFP 본체에 DP 본체
추고 MFP 본체에 꽂습니다 . (A) 를 올립니다 .
2.나사 M4×14TP(G) 각 2 개로 고정쇠 (C) 와 4.DP 본체 (A) 를 미끄러트려 힌지부를 고정쇠
고정쇠 (C*) 를 고정합니다 . (C) 의 걸쇠 (5) 에 끼웁니다 .
固定金具の取り付け（DP-771） DP 本体の取り付け 5.ピン (F)1 本とビス M4×14TP(G)2 本で DP 本

1.右側に固定金具 (C)、左側に幅広の固定金具 3.DP 本体 (A) のヒンジ部の穴 (3) と固定金具体 (A) を MFP 本体に固定する。
(C*) のそれぞれの突起 (1) と MFP 本体の穴 (C) のピン (4) を合わせ、MFP 本体に DP 本体
(2) を合わせ、 MFP 本体に差し込む。 (A) を乗せる。
2.ビス M4×14TP(G) 各 2 本で固定金具 (C) と 4.DP 本体 (A) を手前にスライドさせ、ヒンジ
固定金具 (C*) を固定する。部を固定金具 (C) の引っ掛け部 (5) にはめ
込む。
3
6
8
A
12
9
11
G
D
10
7
Install the angle control fitting. To adjust DP open-close angle 30 degrees 9.Remove stop ring (11) of angle control fitting
To adjust DP open-close angle 60 degrees 7.Open the upper cover (6) of the DP (A). (D) that has been installed in step 6 to
6.Install angle control fitting (D) at the rear side 8.Remove the 3 TP screws (7) and the screw remove shaft (12).
of the right hinge with two M4 × 14TP screws (8), and remove the strap (9) from the rear
(G). cover (10). Then remove the DP (A) rear
cover (10).
Installer la fixation d’angle. Pour régler l’angle d’ouverture/de fermeture 9.Retirer l’anneau de butée (11) de la fixation
Pour régler l’angle d’ouverture/de fermeture du DP de 30 degrés d’angle (D) installée à l’étape 6 pour enlever
du DP de 60 degrés 7.Ouvrir le couvercle supérieur (6) du DP (A). la tige (12).
6.Placer la fixation d’angle (D) à l’arrière de la 8.Déposer les 3 vis TP (7) et la vis (8), puis
charnière droite à l’aide des deux vis TP M4 déposer la courroie (9) du couvercle arrière
× 14 (G). (10). Déposer ensuite le couvercle arrière
(10) du DP (A).
Instale el herraje de control de ángulo. Para ajustar el DP, abra o cierre el ángulo 30 9.Retire el anillo de retención (11) del herraje
Para ajustar el DP, abra o cierre el ángulo 60 grados de control de ángulo (D) que se instaló en el
grados 7.Abra la cubierta superior (6) del DP (A). paso 6 para retirar el eje (12).
6.Instale el herraje de control de ángulo (D) en 8. Quite los 3 tornillos TP (7) y el tornillo (8) y
el lado trasero de la bisagra derecha con quite la correa (9) de la cubierta trasera (10).
dos tornillos TP M4 × 14 (G). Después, quite la cubierta trasera (10) del
DP (A).
Installieren der Winkeleinstellbefestigung. Einstellen des Öffnungs-/Schließungswin- 9.Anschlagring (11) von der Winkeleinstellbef-
Einstellen des Öffnungs-/Schließungswin- kels des DP um 30 Grad estigung (D) abnehmen, die in Schritt 6 mon-
kels des DP um 60 Grad 7. Die obere Abdeckung (6) des DP (A) öffnen. tiert wurde, um die Welle (12) zu entfernen.
6.Winkeleinstellbefestigung (D) an der Rück- 8. Die 3 TP-Schrauben (7) und die Schraube (8)
seite des rechten Scharniers mit zwei M4 × entfernen und dann den Riemen (9) von der
14TP Schrauben (G) befestigen. hinteren Abdeckung (10) abnehmen. Dann die
hintere Abdeckung (10) des DP (A) abnehmen.
Montaggio dell’accessorio di regolazione Per regolare l’angolo di chiusura / apertura 9.Rimuovere l’anello di bloccaggio (11)
angolare. del DP a 30 gradi dell’accessorio di regolazione angolare (D)
Per regolare l’angolo di chiusura / apertura 7.Aprire il pannello superiore (6) del DP (A). che era stato installato al Punto 6 per
del DP a 60 gradi 8.Rimuovere le 3 viti TP (7) e la vite (8), e rimuovere l’albero (12).
6.Montare l’accessorio di regolazione ango- quindi rimuovere la cinghietta (9) dal coper-
lare (D) sul lato posteriore della cerniera chio posteriore (10). Quindi rimuovere il
destra con due viti M4 × 14TP (G). coperchio posteriore (10) del DP (A).
安装角度控制附件。若要将 DP 的开关角度调整为 30 度 9.拆下在第 6 步中安装的角度控制配件（D）的

若要将 DP 的开关角度调整为 60 度 7.打开 DP（A）的上盖板（6）。止动环（11），以将轴（12）拆下。
6.在右部铰链的后部使用两颗 M4×14TP 螺钉 8.拆除 3 颗 TP 螺丝 (7) 和 1 颗螺丝 (8)，将带
（G）安装角度控制附件（D）。子 (9) 从后盖板 (10) 上拆除，拆下 DP 主机
(A) 的后盖板 (10)。
각도규제쇠의 부착 DP 개폐 각도를 30 도로 설정하는 경우 9.순서 6 에서 부착한 각도규제쇠 (D) 의 스톱

DP 개폐각도를 60 도로 설정하는 경우 7.DP 본체 (A) 의 DP 윗커버 (6) 를 엽니다 . 링 (11) 1 개를 제거하고 시프트 (12) 를 제거
6.우 힌지 뒷측에 나사 M4×14TP(G) 2 개로 8.TP 나사 (7) 3 개와 나사 (8) 1 개를 빼고 스 합니다 .
각도규제쇠 (D) 를 부착합니다 . 트랩 (9) 을 뒷 커버 (10) 에서 제거해 DP 본
체 (A) 의 뒷 커버 (10) 를 제거합니다 .
角度規制金具の取り付け DP 開閉角度を 30 度に設定する場合 9.手順 6 で取り付けた角度規制金具 (D) のス

DP 開閉角度を 60 度に設定する場合 7.DP 本体 (A) の DP 上カバー(6) を開く。トップリング (11)1 個を外し、シャフト
6.右ヒンジ後側にビス M4×14TP(G)2 本で角度 8.TP ビス (7)3 本とビス (8)1 本を外し、スト (12) を取り外す。
規制金具 (D) を取り付ける。ラップ (9) を後カバー(10) から外して、DP
本体 (A) の後カバー(10) を取り外す。
4
11 14
12
12
14
15
13
10.Insert shaft (12) into the rear side of the right Connect the DP signal line (DP-770 only) 14.Remove the DP cable connection cap (15)
hinge. For the DP-771, proceed to step 13 on page 7. from the DP cable connection cover (14).
11.Attach stop ring (11) to the notch of shaft 13.Remove the screw (13) and remove the DP
(12) and secure shaft (12). cable connection cover (14).
12.Use the 3 TP screws (7) and the screw (8) to
replace the rear cover (10) removed in step
8.
10.Insérer la tige (12) à l’arrière de la charnière Raccorder le circuit de transmission (DP-770 14.Déposer le chapeau de la connexion du
droite. uniquement) câble du DP (15) du couvercle de la connex-
11.Fixer l’anneau de butée (11) sur l’encoche Pour le DP-771, passer à l'étape 13 en page 7. ion du câble du DP (14).
de la tige (12) et mettre en place la tige (12). 13.Déposer la vis (13) et déposer le couvercle
12.Reposer le couvercle arrière (10) déposé à de la connexion du câble du DP (14).
l'étape 8 et le fixer à l'aide des 3 vis TP (7) et
de la vis (8).
10.Inserte el eje (12) en el lado trasero de la Conecte la línea de señales del DP (DP-770 14.Quite la tapa de conexión del cable del DP
bisagra derecha. solamente) (15) de la cubierta de conexión del cable del
11.Fije el anillo de retención (11) a la muesca Para el DP-771, vaya al paso 13 de la página 7. DP (14)
del eje (12) y asegure el eje (12). 13.Quite el tornillo (13) y quite la cubierta de
12.Use los 3 tornillos TP (7) y el tornillo (8) para conexión del cable del DP (14).
volver a colocar la cubierta trasera (10) qui-
tada en el paso 8.
10.Welle (12) in die Rückseite des rechten Anschließen der DP-Signalleitungen (nur 14.Die Kappe (15) des DP-Kabelanschlusses
Scharniers einsetzen. DP-770) von der Abdeckung (14) des DP-Kabelan-
11.Anschlagring (11) an der Wellenkerbe (12) Beim DP-771 weitergehen zu Schritt 13 auf schlusses abnehmen.
anbringen und Welle befestigen (12). Seite 7.
12.Die in Schritt 8 ausgebaute hintere Abdeck- 13.Die Schraube (13) entfernen und die
ung (10) mittels der 3 TP-Schrauben (7) und Abdeckung (14) des DP-Kabelanschlusses
der Schraube (8) wieder anbringen. abnehmen.
10. Inserire l’albero (12) nella parte posteriore della Collegare la linea del segnale DP (solo DP- 14.Rimuovere il cappuccio (15) per la connes-
cerniera destra. 770) sione del cavo DP dal coperchio di connes-
11. Applicare l’anello di bloccaggio (11) nell’incavo Per il DP-771, procedere al passo 13 a pagina sione del cavo DP (14).
dell’albero (12) e assicurare l’albero (12). 7.
12. Utilizzare le 3 viti TP (7) e la vite (8) per ricollo- 13.Rimuovere la vite (13) e quindi rimuovere il
care il coperchio posteriore (10) rimosso nel coperchio di la connessione del cavo DP
passo 8. (14).
10.将轴（12）插入到右部铰链的后部。连接 DP 信号线（仅限 DP-770） 14.从 DP 电缆连接盖板 (14) 上拆下 DP 电缆连接

11.将止动环（11）安装到轴（12）的切口并将轴 DP-771 跳至 P7 的步骤 13。用盖 (15)。
（12）固定。 13.拆除 1 颗螺丝 (13)，拆下 DP 电缆连接盖板
12.使用 3 颗树脂固定螺丝 (7) 和 1 颗螺丝 (8) (14)。
按原样安装在步骤 8 中拆下的后盖板 (10)。
10.우 힌지 뒷측에 시프트 (12) 를 삽입합니다 . DP 신호선의 접속（DP-770 만） 14.DP 케이블 접속용커버 (14) 에서 DP 케이블
11.스톱링 (11) 을 시프트 (12) 의 구에 부착하고 DP-771 은 P7 의 순서 13 으로 진행 . 접속용 덮개 (15) 를 제거합니다 .
시프트 (12) 를 고정합니다 . 13.나사 (13) 1 개를 빼고 DP 케이블 접속커버
12.순서 8 에서 떼어낸 뒷 커버 (10) 를 수지고 (14) 를 제거합니다 .
정 나사 (7) 3 개와 나사 (8) 1 개로 원래 자리
에 부착합니다 .
10.右ヒンジ後側にシャフト (12) を挿入する。 DP 信号線の接続（DP-770 のみ） 14.DP ケーブル接続用カバー(14) から DP ケー

11.ストップリング (11) をシャフト (12) の溝 DP-771 は P7 の手順 13 へ進む。ブル接続用フタ (15) を取り外す。
に取り付け、シャフト (12) を固定する。 13.ビス (13)1 本を外して、DP ケーブル接続カ
12.手順 8 で外した後カバー(10) を TP ビスバー(14) を外す。
(7)3 本とビス (8)1 本で元通り取り付ける。
5
E
16
18
17 14
14
13
15.Pass the DP signal line (16) through the 16.Plug the DP signal line connector (17) into 17.Attach the DP cable cover (E) to the DP
right-hand hole in the DP cable cover (E) the connector (18) on the ISC PWB. cable connection cover (14) and install the
and then pass the DP signal line (16) DP cable connection cover (14) using the
through the DP cable connection cover (14). screw (13) removed in step 13.
Proceed to step 22 on page 10
15.Faire passer le câble du circuit de transmis- 16.Enficher le connecteur du câble du circuit de 17.Fixer le couvercle du câble du DP (E) sur le
sion du DP (16) dans le trou se trouvant à transmission du DP (17) dans le connecteur couvercle de la connexion du câble du DP
droite sur le couvercle du câble du DP (E) (18) sur l'ISC PWB. (14) et installer le couvercle de la connexion
puis faire passer le câble du circuit de trans- du câble du DP (14) à l'aide de la vis (13)
mission du DP (16) dans le couvercle de la déposée à l'étape 13.
connexion du câble du DP (14). Passer à l'étape 22 de la page 10.
15.Pase la línea de señales del DP (16) a 16.Enchufe el conector de la línea de señales 17. Fije la cubierta del cable del DP (E) a la
través del orificio derecho de la cubierta del del DP (17) al conector (18) PWB del ISC. cubierta de conexión del cable del DP (14) e
cable del DP (E) y, después, pase la línea de instale la cubierta de conexión del cable del
señales del DP (16) a través de la cubierta DP (14) usando el tornillo (13) quitado en el
de conexión del cable del DP (14). paso 13.
Vaya al paso 22 de la página 10.
15.Die DP-Signalleitung (16) durch die rechte 16.Den Stecker (17) der DP-Signalleitung an 17.Die DP-Kabelabdeckung (E) an der Abdeck-
Öffnung in der DP-Kabelabdeckung (E) füh- den Stecker (18) der ISC-Leiterplatte ung (14) des DP-Kabelanschlusses anbrin-
ren und dann die DP-Signalleitung (16) anschließen. gen und die Abdeckung (14) des DP-
durch die Abdeckung (14) des DP-Kabelan- Kabelanschlusses mittels der in Schritt 13
schlusses führen. entfernten Schraube (13) befestigen.
Weitergehen zu Schritt 22 auf Seite 10.
15.Passare la linea del segnale DP (16) attra- 16.Inserire il connettore (17) della linea del seg- 17..Fissare il coperchio del cavo DP (E) al
verso il foro al lato destro nel coperchio del nale DP nel connettore (18) sull'ISC PWB. coperchio di connessione del cavo DP (14),
cavo DP (E), e quindi passare la linea del e quindi installare il coperchio di connes-
segnale DP (16) attraverso il coperchio di sione del cavo DP (14) utilizzando la vite
connessione del cavo DP (14). (13) rimossa nel passo 13.
Procedere al passo 22 a pagina 10.
15.将 DP 信号线 (16) 穿过 DP 电缆盖板 (E) 的右 16.将 DP 信号线连接器 (17) 与 ISC 电路板的接 17.将 DP 电缆盖板 (E) 安装到 DP 电缆连接盖板
侧的孔，接着将 DP 信号线 (16) 穿过 DP 电缆插件 (18) 相连接。 (14) 上，使用步骤 13 中拆下的 1 颗螺丝
连接盖板 (14)。 (13) 来安装 DP 电缆连接盖板 (14)。
跳至 P10 的步骤 22。
15.DP 케이블커버 (E) 의 우측 구멍에 DP 신호 16.DP 신호선 커넥터 (17) 를 ISC 기판의 커넥 17.DP 케이블 커버 (E) 를 DP 케이블 접속커버
선 (16) 을 통과시키고 또한 , DP 케이블 접 터 (18) 에 접속합니다 . (14) 에 부착하고 순서 13 에서 제거한 나사
속용 커버 (14) 에 DP 신호선 (16) 을 통과시 (13) 1 개로 DP 케이블 접속커버 (14) 를 부
킵니다 . 착합니다 .
P10 의 순서 22 로 진행 .
15.DP ケーブルカバー(E) の右側の穴に DP 信号 16.DP 信号線コネクター(17) を ISC 基板のコネ 17.DP ケーブルカバー(E) を DP ケーブル接続カ
線 (16) を通し、さらに DP ケーブル接続用カクター(18) に接続する。バー(14) に取り付け、手順 13 で外したビス
バー(14) に DP 信号線 (16) を通す。 (13)1 本で DP ケーブル接続カバー(14) を取
り付ける。
P10 の手順 22 へ進む。
6
20
22
21
19
Connect the DP signal line (DP-771 only) 14.Remove the DP cable connection cap (22)
13.Remove the 8 screws (19) and remove the from the DP cable connection cover (21).
upper rear cover (20) of the MFP.
Raccorder le circuit de transmission (DP-771 14.Déposer le chapeau de la connexion du

uniquement) câble du DP (22) du couvercle de la connex-
13.Déposer les 8 vis (19) et déposer le couver- ion du câble du DP (21).
cle arrière supérieur (20) du MFP.
Conecte la línea de señales del DP (DP-771 14.Quite la tapa de conexión del cable del DP
solamente) (22) de la cubierta de conexión del cable del
13.Quite los 8 tornillos (19) y quite la cubierta DP (21)
trasera superior (20) del MFP.
Anschließen der DP-Signalleitungen (nur 14.Die Kappe (22) des DP-Kabelanschlusses

DP-771) von der Abdeckung (21) des DP-Kabelan-
13.Die 8 Schrauben (19) entfernen und die schlusses abnehmen.
obere hintere Abdeckung (20) des MFP
abnehmen.
Collegare la linea del segnale DP (solo DP- 14.Rimuovere il cappuccio (22) per la connes-
771) sione del cavo DP dal coperchio di connes-
13.Rimuovere le 8 viti (19) e quindi rimuovere il sione del cavo DP (21).
coperchio superiore posteriore (20)
dell'MFP.
连接 DP 信号线（仅限 DP-771） 14.从 DP 电缆连接盖板 (21) 上拆下 DP 电缆连接

13.拆除 8 颗螺丝 (19)，拆下 MFP 主机的后上方用盖 (22)。
盖板 (20)。
DP 신호선의 접속（DP-771 만） 14.DP 케이블 접속용커버 (21) 에서 DP 케이블

13.나사 (19) 8개를 제거하고 MFP 본체의 뒷면 접속용 덮개 (22) 를 제거합니다 .
상커버 (20) 를 떼어 냅니다 .
DP 信号線の接続（DP-771 のみ） 14.DP ケーブル接続用カバー(21) から DP ケー

13.ビス (19)8 本を外し、MFP 本体の後上カバーブル接続用フタ (22) を取り外す。
(20) を取り外す。
7
E
23
24 21
15.Pass the DP signal line (23) through the right-hand hole in the DP cable cover (E). Then pass the 16.Install the DP cable cover (E) and DP cable
red CIS data line (24) through the left-hand hole. connection cover (21).
NOTICE
Pass the DP signal line (23) and CIS data line (24) through the same hole could result in abnor-
mal images. Be sure that they pass through separate holes as shown in the figure.
15.Faire passer le câble du circuit de transmission du DP (23) dans le trou se trouvant à droite sur le 16.Installer le couvercle du câble du DP (E) et
couvercle du câble du DP (E). Faire ensuite passer le câble rouge de la ligne des données du le couvercle de la connexion du câble du DP
CIS (24) par le trou se trouvant côté gauche. (21).
AVIS
Faire passer le câble du circuit de transmission du DP (23) et le câble de la ligne des données du CIS (24)
dans le même passage de câble risque de résulter en production d'images anormales. S'assurer que ces
deux câbles sont tirés dans des passages de câble diff'érents comme illustré ici.
15.Pase la línea de señales del DP (23) a través del orificio derecho de la cubierta del cable del DP 16.Instale la cubierta del cable del DP (E) y la
(E). Después, pase la línea de datos CIS roja (24) a través del orificio izquierdo. cubierta de conexión del cable del DP (21).
AVISO
Si pasa la línea de señales del DP (23) y la línea de datos CIS (24) a través del mismo orificio
podría provocar imágenes anormales. Asegúrese de que pasen a través de orificios distintos
como aparece en la ilustración.
15.Die DP-Signalleitung (23) durch die rechte Öffnung in der DP-Kabelabdeckung (E) führen. Dann 16.Die DP-Kabelabdeckung (E) und die
die rote CIS-Signalleitung (24) durch die linke Öffnung führen. Abdeckung (21) des DP-Kabelanschlusses
HINWEIS anbringen.
Wenn Sie die DP-Signalleitung (23) und die CIS-Datenleitung (24) durch dieselbe Öffnung füh-
ren, könnte es zu Bildfehlern kommen. Achten Sie darauf, dass die Leitungen wie abgebildet
durch verschiedene Öffnungen geführt werden.
15.Passare la linea del segnale DP (23) attraverso il foro al lato destro nel coperchio del cavo DP 16.Installare il coperchio del cavo DP (E) e il
(E). Quindi passare la linea dati rossa CIS (24) attraverso il foro al lato sinistro. coperchio di connessione del cavo DP (21).
NOTIFICA
Facendo passare la linea del segnale DP (23) e la linea dati CIS (24) attraverso lo stesso foro,
potrebbe causare immagini anormali. Assicurarsi che tali linee passino attraverso fori separati,
come viene mostrato nella figura.
15.将 DP 信号线 (23) 穿过 DP 电缆盖板 (E) 的右侧的孔，接着将红色的 CIS 数据线 (24) 穿过左侧的 16.将DP电缆盖板(E)安装到DP电缆连接盖板(21)
孔。上。
注意
DP 信号线（23）与 CIS 数据线（24）如果穿过同一个孔，可能会发生图像异常，因此必须如图所示
分别穿过左右两侧的孔。
15.DP 케이블커버 (E) 의 우측 구멍에 DP 신호선 (23) 을 통과시킵니다 . 거기에 좌측 구멍에 적색 16.DP 케이블 커버 (E) 를 DP 케이블 접속용커
CIS 데이터선 (24) 을 통과시킵니다 . 버 (21) 에 부착합니다 .
주의
DP 신호선（23）과 CIS 데이터선（24）을 같은 구멍에 통과시키면 이상화상이 발생할 가능성이
있기 때문에 그림과 같이 좌우의 구멍에 각각 넣을 것 .
15.DP ケーブルカバー(E) の右側の穴に DP 信号線 (23) を通す。さらに左側の穴に赤色の CIS データ 16.DP ケーブルカバー(E) を DP ケーブル接続用
線 (24) を通す。カバー(21) に取り付ける。
注意
DP 信号線（23）と CIS データ線（24）
を同じ穴に通すと異常画像が発生する可能性があるため、図
の様に左右の穴に別々に入れること。
8
27
M
25
23 M
26
17.Plug the DP signal line connector (23) into Installing the DP relay PWB 19.Secure the DP relay PWB (M) with two
the connector (25) on the ISC PWB. 18.Connect connector (26) on the DP relay M3 x 8 screws (N).
PWB (M) to connector (27) on the MFP.
17.Enficher le connecteur du câble du circuit de Installation de la carte de circuit imprimé 19.Fixer la carte de circuit imprimé relais du DP
transmission du DP (23) dans le connecteur relais du DP (M) avec deux vis M3 x 8 (N).
(25) sur l'ISC PWB. 18.Raccorder le connecteur (26) sur la carte de
circuit imprimé relais du DP (M) au
connecteur (27) sur le MFP.
17.Enchufe el conector de la línea de señales Instalación del PWB del relé del DP 19.Asegure el PWB del relé del DP (M) con dos
del DP (23) al conector (25) PWB del ISC. 18.Conecte el conector (26) del PWB del relé tornillos M3 x 8 (N)
del DP (M) al conector (27) del MFP.
17.Den Stecker (23) der DP-Signalleitung an nstallieren der DP-Relaisleiterplatte 19.Die DP-Relaisleiterplatte (M) mit zwei
den Stecker (25) der ISC-Leiterplatte 18.Den Stecker (26) an der DP- M3 x 8 Schrauben (N) befestigen.
anschließen. Relaisleiterplatte (M) mit dem Stecker (27)
am MFP verbinden
17.Inserire il connettore (23) della linea del seg- Installazione della scheda a circuiti stampati 19.Fissare la scheda a circuiti stampati di
nale DP nel connettore (25) sull'ISC PWB. di comunicazione DP comunicazione DP (M) con due viti M3 x 8
18.Collegare il connettore (26) sulla scheda a (N).
circuiti stampati di comunicazione DP (M) al
connettore (27) sull’MFP.
17.将DP信号线连接器(23)与ISC电路板的接插件安装 DP 中继板 19.用两颗 M3×8 螺钉（N）固定 DP 中继板（M）。

(25) 相连接。 18.将 DP 中继板（M）上的接插件（26）连接至
MFP 上的接插件（27）。
17.DP 신호선 커넥터 (23) 를 ISC 기판의 커넥 DP 중계기판의 부착 19.DP 중계기판 (M) 을 나사 M3×8(N) 2 개로
터 (25) 에 접속합니다 . 18.DP 중계기판 (M) 의 커넥터 (26) 를 MFP 본 고정합니다 .
체의 커넥터 (27) 에 접속합니다 .
17.DP 信号線コネクター(23) を ISC 基板のコネ DP 中継基板の取り付け 19.DP 中継基板 (M) をビス M3×8(N)2 本で固定
クター(25) に接続する。 18.DP 中継基板 (M) のコネクター(26) を、MFP する。
本体のコネクター(27) に接続する。
9
A
B
24
29
28 M
B
20.Plug the CIS data line (24) into the connec- Fasten the original mat.
tor (28) on the DP relay PWB (M). 22.Place original mat (B) with its Velcro (29) upward over the contact glass.
21.Replace the upper rear cover (20) of the Align original mat (B) corner that has 90 degrees of angle with the inner left corner of the
MFP using the 8 screws (19). original instruction panel.
23.Close DP (A) and attach original mat (B) onto it with Velcro.
20.Enficher le câble de la ligne des données du Fixer la plaque d’original.

CIS (24) dans le connecteur (28) de la carte 22.Placer la plaque d’original (B) sur la vitre d’exposition, en orientant les bandes Velcro (29) vers le
de circuit imprimé relais du DP (M). haut.
21.Reposer le couvercle arrière supérieur (20) Aligner le coin du plateau d'original (B) faisant un angle de 90 degrés avec le coin gauche
sur le MFP à l'aide des 8 vis (19). interne du panneau d'instructions d'original.
23.Abaisser le DP (A) et y fixer la plaque d’original (B) à l’aide des bandes Velcro.
20.Enchufe la línea de datos CIS (24) al conec- Fije la alfombrilla para originales.
tor (28) PWB del relé del DP (M). 22.Coloque la alfombrilla para originales (B) con el velcro (29) hacia arriba sobre el cristal de con-
21.Vuelva a colocar la cubierta trasera superior tacto.
(20) del MFP usando los 8 tornillos (19). Alinee la esquina que tiene un ángulo de 90 grados de la alfombrilla para originales (B)
con la esquina interior izquierda del panel de instrucciones para el original.
23.Cierre el DP (A) y fije la alfombrilla para originales (B) con el velcro.
20.Die CIS-Datenleitung (24) an den Stecker Befestigen der Originalmatte.

(28) auf der DP-Relaisleiterplatte (M) 22.Die Originalmatte (B) mit dem Klettband (29) nach oben über das Kontaktglas legen.
anschließen. Die Ecke der Originalmatte (B), die einen 90-Grad-Winkel aufweist, mit der linken, inneren
21.Die obere hintere Abdeckung (20) des MFP Kante des Originalbedienfeldes ausrichten.
wieder mit den 8 Schrauben (19) anbringen. 23.Den DP (A) schließen und die Originalmatte (B) mit dem Klettband auf ihm befestigen.
20.Inserire la linea dati CIS (24) nel connettore Fissaggio del tappetino originale.
(28) sulla scheda a circuiti stampati di comu- 22.Posizionare il tappetino originale (B) con il velcro (29) rivolto verso l’alto sul vetro di appoggio.
nicazione DP (M). Allineare l’angolo di 90 gradi del coprioriginale (B) con l’angolo interno sinistro del pan-
21.Ricollocare il coperchio superiore posteriore nello di controllo originale.
(20) dell'MFP utilizzando le 8 viti (19). 23.Chiudere il DP (A) e applicarvi il tappetino originale (B) con il velcro.
20.将 CIS 数据线 (24) 连接到 DP 中继电路板粘贴原稿垫。

(M) 上的接插件 (28) 上。 22.将原稿垫（B）放置在稿台玻璃上，并使魔术贴（29）向上。
21.使用 8 颗螺丝 (19) 按原样安装 MFP 主机的后将原稿垫（B）的 90 度角对准原稿指示板的内部左角。
上方盖板 (20)。 23.关闭 DP（A），使原稿垫（B）粘贴到 DP 上。
20.DP 중계기판 (M) 상의 커넥터 (28) 에 CIS 데 원고매트 부착

이터선 (24) 을 접속합니다 . 22.매직테이프 (29) 를 위로 향하게 하고 원고매트 (B) 를 원고대 유리판에 놓습니다 .
21.나사 (19) 8 개로 MFP 본체 뒷면 상커버 (20) 원고매트 (B) 는 90° 가 되어 있는 각을 원고 지시판의 좌측 안에 맞출 것 .
를 원래대로 부착합니다 . 23.DP 본체 (A) 를 내리고 원고매트 (B) 를 DP 본체 (A) 에 부착합니다 .
20.DP 中継基板 (M) 上のコネクター(28) に CIS 原稿マットの貼り付け

データ線 (24) を接続する。 22.マジックテープ (29) を上に向けて、原稿マット (B) をコンタクトガラス上に置く。
21.ビス (19)8 本で、MFP 本体の後上カバー(20) 原稿マット (B) は 90° になっている角を原稿指示板の左奥に合わせること。
を元通り取り付ける。 23.DP 本体 (A) を下ろし、原稿マット (B) を DP 本体 (A) に貼り付ける。
10
I
H
J
Installing the hinge cover (DP-771 only) 25.Install the right hinge cover (I) using the M3
For the DP-770, proceed to step 26 on page 12. × 8 screw BLACK (J).
24.Install the left hinge cover (H).
Installation des couvercles de charnière 25.Installer le couvercle de la charnière droite

(DP-771 uniquement) (l) à l'aide de la vis M3 × 8 NOIRE (J).
Pour le DP-770, passer à l'étape 26 de la page
12.
24.Installer le couvercle de la charnière gauche
(H).
Instalación de la cubierta de las bisagras 25.Instale la cubierta de la bisagra derecha (I)

(DP-771 solamente) usando el tornillo M3 × 8 NEGRO (J).
Para el DP-770, vaya al paso 26 de la página
12.
24.Instale la cubierta de la bisagra izquierda
(H).
Installieren der Scharnierabdeckung 25.Die rechte Scharnierabdeckung (I) mit der

(nur DP-771) M3 × 8 Schraube SCHWARZ (J) anbringen.
Beim DP-770 gehen Sie zum Schritt 26 auf
Seite 12 weiter.
24.Die linke Scharnierabdeckung (H) anbrin-
gen.
Installazione del coperchio cerniera 25.Installare il coperchio cerniera destra (I) uti-
(solo DP-771) lizzando la vite M3 × 8 NERA (J).
Per DP-770, procedere con il punto 26 a pagina
12.
24.Installare il coperchio cerniera sinistra (H).
安装铰链盖板（仅限 DP-771） 25.使用 1 颗 M3×8 螺丝 BLACK(J) 来安装右部铰

DP-770 跳至 P12 的步骤 26。链盖板 (I)。
24.安装左部铰链盖板 (H)。
힌지커버 부착（DP-771 만） 25.나사 M3×8BLACK(J) 1 개로 우측 힌지커버

DP-770 은 P12 의 순서 26 으로 진행 . (I) 를 부착합니다 .
24.좌측 힌지커버 (H) 를 부착합니다 .
ヒンジカバーの取り付け（DP-771 のみ） 25.ビス M3×8BLACK(J)1 本で右ヒンジカバー

DP-770 は、
P12 の手順 26 に進む。 (I) を取り付ける。
24.左ヒンジカバー(H) を取り付ける。
11
(a)
(b) K
L
Adhere the label 27.Adhere Label “Operation procedure” (K) of 28.Adhere Caution label “Original face up!” (L)
26.Clean the label on the original table with which the language corresponding to the of which the language corresponding to the
alcohol. destination of the MFP onto the existing destination of the MFP onto the label on the
label on the original table. Figure (a) original table. Figure (b)
Coller l’étiquette relative 27.Coller l'étiquette “Processus opératoire” (K) 28.Coller l'étiquette de mise en garde “Original
26.Avec de l'alcool, nettoyer létiquette se trou- dans la langue correspondant au destina- en haut!” (L) dans la langue correspondant
vant sur le plateau d'original. taire du MFP sur l'étiquette existante sur le au destinataire du MFP sur l'étiquette du
plateau d'original du DP. Figure (a) plateau d'original. Figure (b)
Pegue la etiqueta 27.Adhiera la etiqueta “Procedimiento opera- 28.Pegue la etiqueta de precaución “¡La cara
26.Limpie con alcohol la etiqueta de la cubierta tivo” (K) del idioma correspondiente al des- del original hacia arriba!” (L), del idioma que
de originales. tino del MFP sobre la etiqueta que se corresponde al destino del MFP, sobre la eti-
encuentra sobre la cubierta de originales. queta en la cubierta de originales. Figura (b)
Figura (a)
Anbringen des Schildes 27.Das Schild „Funktionsanweisung“ (K) in der 28.Das Warnschild „Originalschriftseite nach
26.Das Schild auf dem Originalbedienfeld mit Sprache des jeweiligen Einsatzlandes des oben!“ (L) in der Sprache des jeweiligen
Alkohol reinigen. MFP auf das vorhandene Schild auf dem Einsatzlandes des MFP auf das vorhandene
Originalbedienfeld aufkleben. Abbildung (a) Schild auf dem Originalbedienfeld aufkle-
ben. Abbildung (b)
Applicazione dell’etichetta 27.Far aderire l’etichetta “Procedure di funzion- 28.Far aderire l’etichetta di avvertenza “Origi-
26.Pulire con alcool l’etichetta sul piano origi- amento” (K) corrispondente alla lingua di nale rivolto verso l’alto!” (L) corrispondente
nale. destinazione dell’MFP, sull’etichetta esis- alla lingua di destinazione dell’MFP,
tente sul piano originale. Figura (a) sull’etichetta del piano originale. Figura (b)
粘贴标签（220V 规格以外） 27.将 “ 动作步骤 ” 标签（K）（其语言与对应 28.将小心标签原稿正面朝上！（L）（其语言与

26.使用酒精清洁原稿台上的标签。的 MFP 销往目的地语言一致）粘贴至原稿台对应的 MFP 销往目的地语言一致）粘贴至原
的现有标签上。图（a）稿台的标签上。图（b）
라벨 부착 (220V 사양이외 ) 27.MFP 본체에 사용하는 국가의 언어에 맞는 28.MFP 본체에 사용하는 국가의 언어에 맞는
26.원고 테이블의 라벨 위를 알코올청소 합니다 . 조작라벨 (K) 을 원고 테이블 라벨위에 붙입 원고표용 라벨 (L) 을 원고 테이블 위에 붙입
니다 . 그림 (a) 니다 . 그림 (b)
ラベルの貼り付け (100V 仕様以外 ) 27.MFP 本体を使用する国の言語に合った操作 28.MFP 本体を使用する国の言語に合った原稿

26.原稿テーブルのラベル上をアルコール清掃ラベル (K) を原稿テーブルのラベル上に貼表向きラベル (L) を原稿テーブルのラベル
する。り付ける。図 (a) 上に貼り付ける。図 (b)
12
20mm 20mm
c
20mm
20mm
[Operation check]
1.To check the machine operation, prepare original (a) where 4 lines (b) are drawn 20 mm from the edges of the A3 sheet and 1 line (c) is drawn at its
center.
2.Connect the power plug of the MFP into the wall outlet and turn the main power switch on.
3.Set the original (a) on the DP and perform a test copy to check the operation and the copy example.
[Vérification du fonctionnement]
1.Pour vérifier le bon fonctionnement de l’appareil, préparer un original (a) sur lequel sont tracées 4 lignes (b) à 20 mm des bords de la feuille A3 et 1
ligne (c) en son axe.
2.Brancher la fiche d’alimentation du MFP sur la prise murale et mettre l’appareil sous tension.
3.Placer l’original (a) sur le DP et effectuer une copie de test pour vérifier le fonctionnement et l’exemple de copie.
[Verifique el funcionamiento]
1.Para comprobar el funcionamiento del aparato, prepare un original (a) que contenga 4 líneas (b) dibujadas a 20 mm de los bordes de la hoja A3 y 1
línea (c) dibujada en el centro.
2.Conecte el enchufe eléctrico del MFP en el tomacorriente de la pared y encienda el interruptor principal.
3.Coloque el original (a) en el DP y haga una copia de prueba para verificar el funcionamiento y el ejemplo de copia.
[Funktionsprüfung]
1.Zum Prüfen der Gerätefunktion das Original (a) vorbereiten, auf das 4 Linien (b) 20 mm von den Kanten des A3-Blattes und 1 Linie (c) in der Mitte
gezeichnet sind.
2.Den Netzstecker am MFP in die Steckdose stecken und den Strom einschalten.
3.Das Original (a) auf den DP legen und eine Testkopie erstellen, um die Funktion und das Kopierbeispiel zu prüfen.
[Verifica del funzionamento]

1.Per verificare il funzionamento della macchina, preparare l’originale (a) tirando 4 linee (b) a 20 mm dai bordi del foglio A3 e una linea (c) al centro.
2.Inserire la spina dell’alimentazione dell’MFP nella presa a muro, quindi posizionare l’interruttore principale su On.
3.Posizionare l’originale(a) sul DP ed eseguire una copia di prova per verificare il funzionamento e l’esempio di copia.
[ 动作确认 ]
1.若要检查机器动作，准备一张 A3 原稿（a），距纸张边缘 20mm 画出 4 条线（b）并且在原稿中心画出 1 条线（c）。
2.将 MFP 的电源插头插入墙壁插座并打开主电源。
3.在 DP 上设定原稿（a）并进行测试复印，确认机器动作和复印样本。
[ 동작확인 ]
1.A3 크기용지의 끝에서 20mm 의 위치에 선 (b) 4 개와 용지 중심에 선 (c) 1 개를 긋고 동작확인용 원고 (a) 를 준비합니다 .
2.MFP 본체의 전원 플러그를 콘센트에 꽂고 주 전원 스위치를 ON 으로 합니다 .
3.원고 (a) 를 DP 본체에 장착하고 시험복사를 합니다 . 동작 및 복사샘플을 확인합니다 .
[ 動作確認 ]
1.A3 サイズ用紙の端から 20mm の位置に線 (b)4 本と、用紙の中心に線 (c)1 本を引いた、動作確認用の原稿 (a) を用意する。
2.MFP 本体の電源プラグをコンセントに差し込み、主電源スイッチを ON にする。
3.原稿 (a) を DP 本体にセットし、テストコピーを行い、動作およびコピーサンプルを確認する。
13
20mm 20mm
c
20mm
20mm
4.Compare original (a) with the copy example. If the gap exceeds the reference value, perform the following adjustments according to the type of the
gap.
Check images of the DP after checking and adjusting images of the MFP. For details, see the service manual.
NOTICE: If there is any image fogging, adjust the U068 DP scanning position. If you change the scanning position with U068, adjust the U071 DP
leading edge timing.
4.Comparer l’original (a) avec l’exemple de copie. Si l’écart excède la valeur de référence, effectuer les réglages suivants en fonction du type d’écart.
Vérifier les images du DP après avoir contrôlé et réglé les images du MFP. Pour plus de détails, se reporter au manuel d’entretien.
AVIS: Si l’image est floue, régler la position de balayage de U068 du DP. Si la position de balayage de U068 est modifiée, régler la synchronisation
du bord d’attaque de U071.
4.Compare el original (a) con el ejemplo de copia. Si la separación supera el valor de referencia, realice los siguientes ajustes según el tipo de separa-
ción.
Compruebe las imágenes del DP después de comprobar y ajustar las imágenes del MFP. Para más detalles, lea el manual de servicio.
AVISO: Si la imagen estuviera borrosa, ajuste la posición de escaneo U068 del DP. Si cambia la posición de escaneo con U068, ajuste la sincroni-
zación de borde superior U071 del DP
4.Das Original (a) mit dem Kopierbeispiel vergleichen. Wenn der Abstand größer als der Bezugswert ist, die folgenden Einstellungen gemäß dem
Abstandstyp durchführen.
Die Bilder des DP nach dem Prüfen und Einstellen der Bilder des MFP prüfen. Weitere Einzelheiten siehe Wartungsanleitung.
HINWEIS: Falls das Bild verschwommen wirkt, ist die U068 DP Scan-Position zu verstellen. Wenn Sie die Scan-Position mit U068 verstellen, müssen
Sie das U071 DP-Vorderkanten-Timing entsprechend verstellen.
4.Confrontare l’originale (a) con l’esempio di copia. Se lo scostamento supera il valore di riferimento, eseguire le seguenti regolazioni in funzione del tipo di scostamento.
Controllare le immagini del DP dopo avere effettuato i controlli e le regolazioni delle immagini sull’MFP. Per ulteriori dettagli leggere il man-
uale d’istruzioni.
NOTIFICA: Se è presente una qualsiasi sfocatura dell’immagine, regolare la posizione di scansione DP U068. Se si cambia la posizione di scansione
con U068, regolare la sincronizzazione del bordo principale DP U071.
4.对比复印样本和原稿（a），如果偏移值在标准值以上时，对偏移原稿进行调整。
对 MFP 本体的图像确认和调整后再对 DP 的图像进行确认。详细内容请参见维修手册。
（注意）如果图像出现底灰，用 U068 来调整 DP 的扫描位置。如果用 U068 更改了扫描位置，则再用 U071 对 DP 的前端定时进行调
4.원고 (a) 와 복사샘플을 비교해 기준치 이상의 차이가 있는 경우 차이에 대해 조정을 합니다 .
MFP 본체의 화상확인 및 조정을 하고나서 DP 본체의 화상확인을 할 것 . 상세는 서비스 매뉴얼을 참조할 것 .
（주의） 화상 카브리가 발생하는 경우 , U068DP 스캔위치 조정을 합니다 . U068 에서 스캔위치를 변경한 경우 U071DP 선단 타이밍 조정을 합니다 .
4.原稿 (a) とコピーサンプルを比較し、基準値以上のずれがある場合、ずれ方に応じて調整を行う。

MFP 本体の画像確認及び調整を行ってから DP 本体の画像確認を行うこと。詳細はサービスマニュアルを参照のこと。
（注意）画像カブリが発生する場合、U068DP 読み取り位置の調整を行う。U068 で読み取り位置を変更した場合、U071DP 先端タイミング調整を行う。
14
Be sure to adjust in the following order. If not, the adjustment cannot be performed correctly.
For checking the angle of leading edge, see page 17. <Reference value> Simplex copying: within ±3.0 mm; Duplex copying: within ±4.0 mm
For checking the angle of trailing edge, see page 20. <Reference value> Simplex copying: within ±3.0 mm; Duplex copying: within ±4.0 mm
When using the original for adjustment, automatic adjustment of magnification, leading edge timing and center line can be performed at a
time.
For the automatic adjustment using the original for adjustment, see page 23.
Veillez à effectuer le réglage en procédant dans l’ordre suivant. Sinon, il sera impossible d’obtenir un réglage correct.
Pour vérifier l’angle du bord avant, reportez-vous à la page 17. <Valeur de référence>Copie recto seul: ±3,0 mm max.; copie recto verso: ±4,0 mm max.
Pour vérifier l’angle du bord arrière, reportez-vous à la page 20. <Valeur de référence>Copie recto seul: ±3,0 mm max.; copie recto verso: ±4,0 mm max.
Lorsque vous utilisez l’original pour effectuer le réglage, vous pouvez effectuer automatiquement le réglage de l’agrandissement, de la syn-
chronisation du bord avant et de la ligne médiane en une seule fois.
Pour le réglage automatique en utilisant l’original pour effectuer le réglage, reportez-vous à la page 23.
Asegúrese de ajustar en el siguiente orden. De lo contrario, el ajuste no puede hacerse correctamente.

Para verificar el ángulo del borde superior, vea la página 17. <Valor de referencia>Copia simple: dentro de ±3,0 mm; Copia duplex: dentro de ±4,0 mm
Para verificar el ángulo del borde inferior, vea la página 20. <Valor de referencia>Copia simple: dentro de ±3,0 mm; Copia duplex: dentro de ±4,0 mm
Cuando utilice el original para el ajuste, puede hacerse un ajuste automático del cambio de tamaño, sincronización del borde superior y línea
central al mismo tiempo.
Para el ajuste automático utilizando el original para el ajuste, vea la página 23.
Die Einstellung in der folgenden Reihenfolge durchführen. Anderenfalls kann die Einstellung nicht korrekt durchgeführt werden.
Angaben zur Prüfung des Winkels der Vorderkante auf Seite 17. <Bezugswert>Simplexkopie: innerhalb ±3,0 mm; Duplexkopie: innerhalb ±4,0 mm
Angaben zur Prüfung des Winkels der Hinterkante auf Seite 20. <Bezugswert>Simplexkopie: innerhalb ±3,0 mm; Duplexkopie: innerhalb ±4,0 mm
Bei Verwendung des Originals für die Einstellung können die automatischen Einstellungen für Vergrößerung, Vorderkanten-Timing und Mittel-
linie gleichzeitig durchgeführt werden.
Angaben zur automatischen Einstellung mithilfe des Originals auf Seite 23.
Accertarsi di eseguire le regolazioni in questa sequenza: in caso contrario, la regolazione non può essere effettuata correttamente.
Per controllare l’angolo del bordo principale, vedere pagina 17. <Valore di riferimento>Copia simplex: entro ±3,0 mm; Copia duplex: entro ±4,0 mm
Per controllare l’angolo del bordo di uscita, vedere pagina 20. <Valore di riferimento>Copia simplex: entro ±3,0 mm; Copia duplex: entro ±4,0 mm
Quando si utilizza l’originale per la regolazione, la regolazione automatica dell’ingrandimento, della sincronizzazione del bordo principale e
della linea centrale possono essere eseguiti contemporaneamente.
Per la regolazione automatica eseguita con l’originale, vedere pagina 23.
必须按照以下步骤进行调整，否则不能达到准确调整的要求。
・确认前端倾斜度第 17 页 < 标准值 > 单面：±3.0mm 以内，双面：±4.0mm 以内
・确认后端倾斜度第 20 页 < 标准值 > 单面：±3.0mm 以内，双面：±4.0mm 以内
使用调整用的原稿时，可以同时自动进行等倍值，前端定时以及中心线的调整。
・通过调整用原稿进行自动调整第 23 页
반드시 하기의 순서로 조정을 할 것 . 순서대로 조정을 하지 않는 경우 바른 조정을 할 수 없습니다 .

・선단경사확인 17 페이지 ＜기준치＞단면：±3.0mm 이내 , 양면：±4.0mm 이내
・후단경사확인 20 페이지 ＜기준치＞단면：±3.0mm 이내 , 양면：±4.0mm 이내
조정용 원고를 사용하면 등배도 조정 , 선단타이밍 조정 , 센터 라인조정의 자동조정이 한번에 수행됩니다 .
・조정용원고에 의한 자동조정 23 페이지
必ず下記の順序で調整を行うこと。順序通りに調整を行わない場合、正しい調整ができない。
・先端斜め確認 17 ページ＜基準値＞片面：±3.0mm 以内、
両面：±4.0mm 以内
・後端斜め確認 20 ページ＜基準値＞片面：±3.0mm 以内、
両面：±4.0mm 以内
調整用原稿を使用すると、等倍度調整、先端タイミング調整、センターライン調整の自動調整が一度におこなえる。
・調整用原稿による自動調整 23 ページ
15
For checking the magnification, see page26. <Reference value> Within ±1.5%
For checking the leading edge timing, see page 28. <Reference value> Within ±2.5 mm
For checking the center line, see page 30. <Reference value> Simplex copying: within ±2.0 mm; Duplex copying: within ±3.0 mm
Pour vérifier l’agrandissement, reportez-vous à la page 26. <Valeur de référence> ±1,5% max.
Pour vérifier la synchronisation du bord avant, reportez-vous à la page 28. <Valeur de référence> ±2,5 mm max.
Pour vérifier la ligne médiane, reportez-vous à la page 30. <Valeur de référence> Copie recto seul: ±2,0 mm max.;
copie recto verso: ±3,0 mm max.
Para verificar el cambio de tamaño, vea la página 26. <Valor de referencia> Dentro de ±1,5 %
Para verificar la sincronización del borde inferior, vea la página 28. <Valor de referencia> Dentro de ±2,5 mm
Para verificar la línea central, vea la página 30. <Valor de referencia> Copia simple: dentro de ±2,0 mm;
Copia duplex: dentro de ±3,0 mm
Angaben zur Prüfung der Vergrößerung auf Seite 26. <Bezugswert> Innerhalb ±1,5 %
Angaben zur Prüfung des Vorderkanten-Timings auf Seite 28. <Bezugswert> Innerhalb ±2,5 mm
Angaben zur Prüfung der Mittellinie auf Seite 30. <Bezugswert> Simplexkopie: innerhalb ±2,0 mm; Duplexkopie: innerhalb ±3,0 mm
Per controllare l’ingrandimento, vedere pagina 26. <Valore di riferimento> Entro ±1,5%
Per controllare la sincronizzazione del bordo principale, vedere pagina 28. <Valore di riferimento> Entro ±2,5 mm
Per controllare la linea centrale, vedere pagina 30. <Valore di riferimento> Copia simplex: entro ±2,0 mm;
Copia duplex: entro ±3,0 mm
・确认等倍值第 26 页 < 标准值 > ±1.5% 以内

・确认前端定时调整第 28 页 < 标准值 > ±2.5mm 以内
・确认中心线第 30 页 < 标准值 > 单面：±2.0mm 以内，双面：±3.0mm 以内
・등배도 확인 26 페이지 ＜기준치＞ ±1.5% 이내

・선단 타이밍 확인 28 페이지 ＜기준치＞ ±2.5mm 이내
・센터 라인확인 30 페이지 ＜기준치＞ 단면：±2.0mm 이내 , 양면：±3.0mm 이내
・等倍度確認 26 ページ＜基準値＞ ±1.5% 以内

・先端タイミング確認 28 ページ＜基準値＞ ±2.5mm 以内
・センターライン確認 30 ページ＜基準値＞片面：±2.0mm 以内、両面：±3.0mm 以内
16
[Checking the angle of leading edge]
1.Check the horizontal gap between line (1) of original (a) and line (2) of copy example positions. If the gap exceeds the reference value, adjust the gap
according to the following procedure.
<Reference value> For single copying: The horizontal gap of line (2) should be within ±3.0 mm.
For duplex copying: The horizontal gap of line (2) should be within ±4.0 mm.
[Vérification de l’angle du bord avant]

1.Vérifier l’écart horizontal entre la position de la ligne (1) de l’original (a) et celle de la ligne (2) de l’exemple de copie. Si l’écart excède la valeur de
référence, le régler selon la procédure suivante.
<Valeur de référence> Pour la copie recto : l’écart horizontal de la ligne (2) doit être de ±3.0 mm.
Pour la copie recto-verso : l’écart horizontal de la ligne (2) doit être de ±4.0 mm.
[Verificación del ángulo del borde superior]

1.Compruebe la separación horizontal entre la línea (1) del original (a) y la línea (2) de las posiciones del ejemplo de copia. Si la separación supera el
valor de referencia, ajústela siguiendo este procedimiento.
<Valor de referencia> Para el copiado por una cara: la separación horizontal de la línea (2) debe estar dentro de ±3.0 mm.
Para el copiado dúplex: la separación horizontal de la línea (2) debe estar dentro de ±4.0 mm.
[Überprüfen des Winkels der Vorderkante]

1.Den horizontalen Abstand zwischen der Linie (1) des Originals (a) und der Linie (2) der Kopierbeispielspositionen prüfen. Wenn der Abstand größer
als der Bezugswert ist, den Abstand mit dem folgenden Verfahren einstellen.
<Bezugswert> Einzelkopie: Der horizontale Abstand der Linie (2) sollte innerhalb von ±3.0 mm liegen.
Duplexkopie: Der horizontale Abstand der Linie (2) sollte innerhalb von ±4.0 mm liegen.
[Controllo dell’angolo del bordo principale]

1.Verificare lo scostamento orizzontale fra la linea (1) dell’originale (a) e la linea (2) delle posizioni dell’esempio di copia. Se lo scostamento supera il
valore di riferimento, regolare lo scostamento stesso seguendo questa procedura.
<Valore di riferimento>Per la copia singola: lo scostamento orizzontale della linea (2) deve limitarsi a ± 3.0 mm.
Per la copia duplex: lo scostamento orizzontale della linea (2) deve limitarsi a ±4.0 mm.
[ 确认前端倾斜度 ]
1.确认原稿（a）上的线（1）和复印样本上的线（2）的左右偏移值。如果偏移值超过标准值，则按照下列步骤进行调整
< 标准值 > 单面复印时，线（2）的左右偏移值：±3.0mm 以内。
　　　　　双面复印时，线（2）的左右偏移值：±4.0mm 以内。
[ 선단 경사확인 ]
1.원고 (a) 의 선 (1) 과 복사샘플의 선 (2) 의 좌우 차이를 확인합니다 . 차이가 기준치 외의 경우 다음의 순서대로 조정을 합니다 .
＜기준체＞단면의 경우 선 (2) 의 좌우차이：±3.0mm 이내
양면의 경우 선 (2) 의 좌우차이：±4.0mm 이내
[ 先端斜め確認 ]
1.原稿 (a) の線 (1) とコピーサンプルの線 (2) の左右のずれを確認する。ずれが基準値外の場合、次の手順で調整を行う。
＜基準値＞片面の場合、線 (2) の左右ずれ：±3.0mm 以内
　　　　　両面の場合、線 (2) の左右ずれ：±4.0mm 以内
17
C (C*)
G
G
C (C*)
C
2. DP-770: Remove the angle control fitting (D). Loosen the 2 M4 × 14TP screws (G) on the left and right fixing fittings (C).
DP-771: Remove the left hinge cover (H) and the angle control fitting (D). Loosen the 2 M4 × 14TP screws (G) on the left and right fixing fittings (C*) (C)
3.Turn adjusting screw (3) at the rear side of the right hinge to adjust the DP position.
For copy example (d): Turn the adjusting screw counterclockwise and move the DP to the inner side.
For copy example (e): Turn the adjusting screw clockwise and move the DP to the front side.
Amount of change per scale: Approx. 1.0 mm
4.Perform a test copy.
2. DP-770: Déposer la fixation d'angle (assurant le contrôle de l'ouverture) (D). Desserrer les 2 vis TP M4 × 14 (G) sur les fixations gauche et droite (C).
DP-771: Déposer le couvercle de la charnière gauche (H) et la fixation d'angle (assurant le contrôle de l'ouverture) (D). Desserrer les 2 vis TP M4 × 14 (G) sur les fixations
gauche et droite (C*) (C).
3. ourner la vis de réglage (3) à l’arrière de la charnière droite pour régler la position du DP.
Pour l’exemple de copie (d) : tourner la vis de réglage dans le sens inverse des aiguilles d’une montre et déplacer le DP vers l’intérieur.
Pour l’exemple de copie (e) : tourner la vis de réglage dans le sens des aiguilles d’une montre et déplacer le DP vers l’avant.
Changement par graduation d’échelle : environ 1.0 mm
4. Effectuer une copie de test.
2. DP-770: quite el herraje de control de ángulo (D). Afloje los 2 tornillos TP M4 × 14 (G) de los herrajes de fijación izquierdo y derecho (C).
DP-771: quite la cubierta de la bisagra izquierda (H) y el herraje de control de ángulo (D). Afloje los 2 tornillos TP M4 × 14 (G) de los herrajes de fijación izquierdo y dere-
cho (C*) (C).
3. Gire el tornillo de ajuste (3) en el lado trasero de la bisagra derecha para ajustar la posición del DP.
Para el ejemplo de copia (d): gire el tornillo de ajuste en sentido antihorario y mueva el DP al lado interno.
Para el ejemplo de copia (e): gire el tornillo de ajuste en sentido horario y mueva el DP al lado frontal.
Magnitud del cambio por escala: aprox. 1.0 mm
4. Haga una copia de prueba.
2. DP-770: Die Winkeleinstellbefestigung (D) entfernen. Die 2 M4 × 14TP Schrauben (G) an den linken und rechten Befestigungshalterung (C) lösen.
DP-771: Die linke Scharnierabdeckung (H) und die Winkeleinstellbefestigung (D) entfernen. Die 2 M4 × 14TP Schrauben (G) an den linken und rechten Befestigungshalter-
ungen (C*) (C) lösen.
3. Die Einstellschraube (3) an der Rückseite des rechten Scharniers einstellen, um die DP-Position einzustellen.
Kopierbeispiel (d): Die Einstellschraube nach links drehen und den DP nach innen schieben.
Kopierbeispiel (e): Die Einstellschraube nach rechts drehen und den DP nach vorne schieben.
Änderung pro Maßstab: Ungefähr 1.0 mm
4. Eine Testkopie erstellen.
2. DP-770: Rimuovere l'accessorio di regolazione angolare (D). Allentare le 2 viti M4 × 14TP (G) sugli accessori di fissaggio (C) destro e sinistro.
DP-771: Rimuovere il coperchio cerniera sinistra (H) e l'accessorio di regolazione angolare (D). Allentare le 2 viti M4 × 14TP (G) sui lati destro e sinistro degli accessori di
fissaggio (C*) (C) destro e sinistro.
3. Ruotare la vite di regolazione (3) sul lato posteriore della cerniera destra per regolare la posizione del DP.
Per l’esempio di copia (d): ruotare la vite di regolazione in senso antiorario e spostare il DP verso l’interno.
Per l’esempio di copia (e): ruotare la vite di regolazione in senso orario e spostare il DP in avanti.
Entità modifica per scala: circa 1.0 mm
4. Eseguire una copia di prova.
2.DP-770 时：拆下角度限制附件 (D)。拧松左右固定附件 (C) 的 2 颗 M4x14TP(G) 螺丝。

DP-771 时：拆下左部铰链盖板 (H) 以及角度限制附件 (D)。拧松左右固定附件 (C*)(C) 的 2 颗 M4x14TP(G) 螺丝。
3.旋转右部铰链的后部的调整螺钉（3）以调整 DP 位置。
对于复印样本 (d)：逆时针旋转调整螺钉并将 DP 移动到内侧。　对于复印样本 (e)：顺时针旋转调整螺钉并将 DP 移动到正面。
按比例尺的更改量：约 1.0mm
4.进行测试复印。
2.DP-770 의 경우：각도규제쇠 (D) 를 제거합니다 . 좌우의 고정쇠 (C) 나사 M4x14TP(G) 2 개를 느슨하게 합니다 .
DP-771 의 경우：좌 힌지커버 (H) 및 각도규제쇠 (D) 를 제거합니다 . 좌우의 고정쇠 (C*)(C) 의 나사 M4x14TP(G) 2 개를 느슨하게 합니다 .
3.우 힌지 뒷측 조정나사 (3) 를 돌려 DP 본체의 위치를 조정합니다 .
복사샘플 (d) 의 경우：조정나사를 좌로 돌려 DP 본체를 안으로 넣습니다 . 복사샘플 (e) 의 경우 ： 조정나사를 오른쪽으로 돌려 DP 본체를 앞으로 뺍니다 .
1 개 변화량：약 1.0mm
4.시험복사를 합니다 .
2.DP-770 の場合：角度規制金具 (D) を取り外す。左右の固定金具 (C) のビス M4x14TP(G)2 本を緩める

DP-771 の場合：左ヒンジカバー(H) および角度規制金具 (D) を取り外す。左右の固定金具 (C*)(C) のビス M4x14TP(G)2 本を緩める。
3.右ヒンジ後側の調整ビス (3) を回し、DP 本体の位置を調整する。
コピーサンプル (d) の場合：調整ビスを左に回し、 DP 本体を奥へ動かす。
コピーサンプル (e) の場合：調整ビスを右に回し、 DP 本体を手前へ動かす。
1 目盛り当たりの変化量：約 1.0mm
4.テストコピーを行う。
18
5.Repeat the steps above until the gap of line (2) of copy example shows the following reference values.
<Reference value> For single copying: The horizontal gap of line (2) should be within ±3.0 mm.
For duplex copying: The horizontal gap of line (2) should be within ±4.0 mm.
6.After adjustment is completed, retighten two M4 × 14TP screws (G) that have been loosened in step 2.
7.Remove the original mat (B) and refit it (see steps 22 and 23 on page 10).
5.Répéter les étapes ci-dessus jusqu’à ce que l’écart de la ligne (2) de l’exemple de copie indique les valeurs de référence suivantes.
<Valeur de référence> Pour la copie recto : l’écart horizontal de la ligne (2) doit être de ±3.0 mm.
Pour la copie recto-verso : l’écart horizontal de la ligne (2) doit être de ±4.0 mm.
6.Une fois le réglage effectué, resserrer les deux vis TP M4 × 14 (G) desserrées à l’étape 2.
7.Retirez le tapis d’original (B) et remettez-le en place. (Reportez-vous aux étapes 22 et 23 à la page 10.)
5.Repita los pasos anteriores hasta que la separación de la línea (2) del ejemplo de copia presente los siguientes valores de referencia.
<Valor de referencia> Para el copiado por una cara: la separación horizontal de la línea (2) debe estar dentro de ±3.0 mm.
Para el copiado dúplex: la separación horizontal de la línea (2) debe estar dentro de ±4.0 mm.
6.Una vez hecho el ajuste, vuelva a apretar los dos tornillos TP M4 × 14 (G) que ha aflojado en el paso 2.
7.Desmonte la plancha de original (B) y vuelva a colocar (vea los pasos 22 y 23 en la página 10).
5.Die obigen Schritte wiederholen, bis der Abstand der Linie (2) des Kopierbeispiels die folgenden Bezugswerte aufweist.
<Bezugswert> Einzelkopie: Der horizontale Abstand der Linie (2) sollte innerhalb von ±3.0 mm liegen.
Duplexkopie: Der horizontale Abstand der Linie (2) sollte innerhalb von ±4.0 mm liegen.
6.Nach der Einstellung die zwei M4 × 14TP Schrauben (G), die in Schritt 2 gelöst wurden, wieder festziehen.
7.Die Originalmatte (B) abnehmen und wieder anbringen (siehe Schritte 22 und 23 auf Seite 10).
5.Ripetere le operazioni sopra descritte fino a quando lo scostamento della linea (2) dell’esempio di copia riporterà i valori di riferimento seguenti.
<Valore di riferimento>Per la copia singola: lo scostamento orizzontale della linea (2) deve limitarsi a ± 3.0 mm.
Per la copia duplex: lo scostamento orizzontale della linea (2) deve limitarsi a ±4.0 mm.
6.Una volta conclusa la regolazione, serrare nuovamente le viti M4 × 14TP (G) che erano state allentate al Punto 2.
7.Rimuovere il coprioriginale (B) e reinserirlo (vedere i passi 22 e 23 a pagina 10).
5.重复上述步骤直至复印样本上的线（2）的偏移值达到标准值范围内。
< 标准值 > 单面时，线（2）的左右偏移值：±3.0mm 以内
　　　　　双面时，线（2）的左右偏移值：±4.0mm 以内
6.调整完成后，重新拧紧在步骤 2 中松开的两颗 M4×14TP 螺钉（G）。
7.拆下原稿垫（B），参照第 10 页的步骤 22 和 23 再次装上。
5.복사샘플 선 (2) 차이가 기준치내가 될 때까지 조정을 반복합니다 .

＜기준치＞단면의 경우 선 (2) 의 좌우차이：±3.0mm 이내
　　　　　양면의 경우 선 (2) 의 좌우차이：±4.0mm 이내
6.조정종료 후 순서 2 에서 느슨하게 한 나사 M4×14TP(G) 2 개를 조입니다 .
7.원고매트 (B) 를 제거하고 10 페이지 순서 22, 23 을 참고로 다시 부착합니다 .
5.コピーサンプルの線 (2) ずれが基準値内になるまで、調整を繰り返す。

＜基準値＞片面の場合、線 (2) の左右ずれ：±3.0mm 以内
　　　　　両面の場合、線 (2) の左右ずれ：±4.0mm 以内
6.調整終了後、手順 2 で緩めたビス M4×14TP(G)2 本を締め付ける。
7.原稿マット (B) を取り外し、
10 ページの手順 22、23 を参考に再度取り付ける。
19
2
1
3mm/4mm
3mm/4mm
a f 2 g
[Checking the angle of trailing edge]

1.Check the gap between line (1) of original (a) and line (2) of copy example. If the gap exceeds the reference value, perform the following adjustment.
<Reference value> For simplex copying: Within ±3.0 mm
For duplex copying: Within ±4.0 mm
[Vérification de l’angle du bord arrière]

1.Vérifiez l’écart entre la ligne (1) de l’original (a) et la ligne (2) de l’exemple de copie. Si l’écart est supérieur à la valeur de référence, effectuez le
réglage suivant.
<Valeur de référence> Copie recto seul: ±3,0 mm max.
Copie recto verso: ±4,0 mm max.
[Verificación del ángulo del borde inferior]

1.Verifique la separación entre la línea (1) del original (a) y la línea (2) de la copia de muestra. Si la superación supera el valor de referencia, haga el
siguiente ajuste.
<Valor de referencia> Para copia simple: Dentro de ±3,0 mm
Para copia duplex: Dentro de ±4,0 mm
[Überprüfen des Winkels der Hinterkante]

1.Die Abweichung der Linie (1) des Originals (a) und der Linie (2) des Kopienmusters prüfen. Überschreitet die Abweichung den Bezugswert, ist die fol-
gende Einstellung durchzuführen.
<Bezugswert> Für Simplexkopie: Innerhalb ±3,0 mm
Für Duplexkopie: Innerhalb ±4,0 mm
[Controllo dell’angolo del bordo di uscita]

1.Controllare la differenza tra la linea (1) dell’originale (a) e la linea (2) della copia di esempio. Se la differenza supera il valore di riferimento, effettuare
la seguente regolazione.
<Valore di riferimento> Per copia simplex: Entro ±3,0 mm
Per copia duplex: Entro ±4,0 mm
[ 确认后端倾斜度 ]
1.确认原稿（a）上的线（1）和复印样本上的线（2）的偏移值。如果超过标准值时，必须进行调整。
< 标准值 > 单面时：±3.0mm 以内
　　　　　双面时：±4.0mm 以内
[ 후단 경사확인 ]
1.원고 (a) 의 선 (1) 과 복사샘플 선 (2) 의 차이를 확인합니다 . 차이가 기준치 외의 경우에는 조정을 합니다 .
＜기준치＞단면의 경우：±3.0m 이내
양면의 경우：±4.0mm 이내
[ 後端斜め確認 ]
1.原稿 (a) の線 (1) とコピーサンプルの線 (2) のずれを確認する。ずれが基準値外の場合は調整をおこなう。
＜基準値＞片面の場合：±3.0mm 以内
　　　　　両面の場合：±4.0mm 以内
20
3
5
A
10
7
4
2.Open the upper cover (3) of the DP (A). 4.Adjust the height of DP. Amount of change per scale: Approx. 0.5
3.Remove the 3 TP screws (4) and the screw Loosen the nut (8). mm (10)
(5), and remove the strap (6) from the rear For copy example (f): Loosen the adjusting Retighten the nut (8).
cover (7). Then remove the DP (A) rear screw (9). 5.Refit the rear cover (7) removed in step 3.
cover (7). For copy example (g): Tighten the adjusting 6.Remove the original mat (B) and refit it (see
screw (9). steps 22 and 23 on page 10).
2.Ouvrir le couvercle supérieur (3) du DP (A) 4.Réglez la hauteur du DP. Quantité de changement par pas: environ
3.Déposer les 3 vis TP (4) et la vis (5) puis Desserrez l’écrou (8). 0,5 mm (10)
déposer la courroie (6) du couvercle arrière Pour l’exemple de copie (f): Desserrez la vis Resserrez l’écrou (8).
(7). Déposer ensuite le couvercle arrière (7) de réglage (9). 5.Reposer le capot arrière (7) déposé à l'étape 3.
du DP (A). Pour l’exemple de copie (g): Serrez la vis de 6.Retirez le tapis d’original (B) et remettez-le
réglage (9). en place. (Reportez-vous aux étapes 22 et
23 à la page 10.)
2.Abra la cubierta superior (3) del DP (A). 4.Ajuste la altura del DP. Cantidad de cambio de escala: Aprox. 0,5 mm (10)
3.Quite los 3 tornillos TP (4) y el tornillo (5) y Afloje la tuerca (8). Vuelva a apretar la tuerca (8).
quite la correa (6) de la cubierta trasera (7). Para la copia de muestra (f): Afloje el tornillo 5.Vuelva a colocar la cubierta (7) desmontada
Después, quite la cubierta trasera (7) del DP de ajuste (9). en el paso 3.
(A). Para la copia de muestra (g): Apriete el 6.Desmonte la plancha de original (B) y vuelva
tornillo de ajuste (9). a colocar (vea los pasos 22 y 23 en la
página 10).
2.Die obere Abdeckung (3) des DP (A) öffnen. 4.Die Höhe des DP einstellen. Änderungsbetrag pro Skalenstrich: ca. 0,5
3.Die 3 TP-Schrauben (4) und die Schraube Lösen Sie die Mutter (8). mm (10)
(5) entfernen und den Riemen (6) von der Für Kopienmuster (f): Lösen Sie die Ein- Ziehen Sie die Mutter (8) wieder fest.
hinteren Abdeckung (7) abnehmen. Dann stellschraube (9). 5.Die in Schritt 3 entfernte hintere Abdeckung
die hintere Abdeckung (7) des DP (A) Für Kopienmuster (g): Die Einstellschraube (7) wieder anbringen.
abnehmen. (9) festziehen. 6.Die Originalmatte (B) abnehmen und wieder
anbringen (siehe Schritte 22und 23 auf Seite 10).
2.Aprire il pannello superiore (3) del DP (A). 4.egolazione dell’altezza del DP Variazione graduale: circa 0,5 mm (10)
3.Rimuovere le 3 viti TP (4) e la vite (5), e Allentare il dado (8). Stringere di nuovo il dado (8).
quindi rimuovere la cinghietta (6) dal coper- Per un esempio di copia (f): Allentare la vite 5.Reinserire il coperchio posteriore (7)
chio posteriore (7). Quindi rimuovere il di regolazione (9). rimosso nel passo 3.
coperchio posteriore (7) del DP (A). Per un esempio di copia (g): Stringere la vite 6.Rimuovere il coprioriginale (B) e reinserirlo
di regolazione (9). (vedere i passi 22 e 23 a pagina 10).
2.打开 DP（A）的上盖板（3）。 4.调整 DP 的高度。每 1 格的移动量：约 0.5mm（10）

3.拆除 3 颗 TP 螺丝 (4) 和 1 颗螺丝 (5)，将带松驰螺母（8）。将螺母（8）按原样紧固好。
子 (6) 从后盖板 (7) 上拆除，拆下 DP 主机测印件（f）时：松弛调整螺丝（9）。 5.重新安装在步骤 3 中拆下的后盖板（7）。
(A) 的后盖板 (7)。测印件（g）时：紧固调整螺丝（9）。 6.拆下原稿垫（B），参照第 10 页的步骤 22 和
23 再次装上。
2.DP 본체 (A) 의 DP 윗 커버 (3) 를 엽니다 . 4.DP 의 높이를 조정합니다 . 1 개 변화량：약 0.5mm(10)

3.TP 나사 (4) 3 개와 나사 (5) 1 개를 제거하고 너트 (8) 를 느슨하게 합니다 . 너트 (8) 를 원래대로 조입니다 .
스트랩 (6) 을 뒷면 커버 (7) 에서 제거해 DP 복사샘플 (f) 의 경우：조정나사 (9) 를 느슨하 5.순서 3 에서 제거한 뒷 커버 (7) 를 원래대로
본체 (A) 의후면 커버 (7) 를 제거합니다 . 게 합니다 . 장착합니다 .
복사샘플 (g) 의 경우：조정나사 (9) 를 조입 6.원고너트 (B) 를 제거하고 10 페이지 순서
니다 . 22, 23 을 참고로 다시 부착합니다 .
2.DP 本体 (A) の DP 上カバー(3) を開く。 4.DP の高さを調整する。 1 目盛り当たりの変化量：約 0.5mm(10)

3.TP ビス (4)3 本とビス (5)1 本を外し、ストナット (8) をゆるめる。ナット (8) を元通り締める。
ラップ (6) を後カバー(7) から外して、DP 本コピーサンプル (f) の場合：調整ビス (9) を 5.手順 3 で取り外した後カバー(7) を元通り
体 (A) の後カバー(7) を取り外す。ゆるめる。取り付ける。
コピーサンプル (g) の場合：調整ビス (9) を 6.原稿マット (B) を取り外し、10 ページの手
締める。順 22、23 を参考に再度取り付ける。
21
2
1
3mm/4mm
3mm/4mm
a f 2 g
7.Make a proof copy again.

8.Repeat steps 1 to 6 until line (2) of copy example shows the following the reference values.
<Reference value> For simplex copying: Within ±3.0 mm
For duplex copying: Within ±4.0 mm
7.Effectuez à nouveau une copie de test.

8.Répétez les étapes 1 à 6 jusqu’à ce que la ligne (2) de l’exemple de copie corresponde aux valeurs de référence suivantes.
<Valeur de référence> Copie recto seul: ±3,0 mm max.
Copie recto verso: ±4,0 mm max.
7.Haga otra copia de prueba.

8.Repita los pasos 1 a 6 hasta que la línea (2) de la copia de muestra tenga los siguientes valores de referencia.
<Valor de referencia> Para copia simple: Dentro de ±3,0 mm
Para copia duplex: Dentro de ±4,0 mm
7.Eine erneute Probekopie anfertigen.

8.Die Schritte 1 bis 6 wiederholen, bis die Linie (2) des Kopienmusters die folgenden Bezugswerte aufweist.
<Bezugswert> Für Simplexkopie: Innerhalb ±3,0 mm
Für Duplexkopie: Innerhalb ±4,0 mm
7.Eseguire di nuovo una prova di copia.

8.Ripetere i passi da 1 a 6 fino a che la linea (2) dell’esempio di copia non mostra i seguenti valori di riferimento.
<Valore di riferimento> Per copia simplex: Entro ±3,0 mm
Per copia duplex: Entro ±4,0 mm
7.再次进行测试复印。
8.反复操作步骤 1~6，直至测印件的线（2）为标准值内。
< 标准值 > 单面时：±3.0mm 以内
　　　　　双面时：±4.0mm 以内
7.다시 시험복사를 합니다 .

8.복사샘플 선 (2) 이 기준치내로 될 때까지 순서 1 ～ 6 을 반복합니다 .
＜기준치＞단면의 경우：±3.0m 이내
양면의 경우：±4.0mm 이내
7.再度テストコピーをおこなう。
8.コピーサンプルの線 (2) が基準値内になるまで、手順 1 ～ 6 を繰り返す。
＜基準値＞片面の場合：±3.0mm 以内
　　　　　両面の場合：±4.0mm 以内
22
[Automatic adjustment using the original for adjustment] 4.Set the original on the DP face down and press the Start key to carry
If there is no DP auto adjustment origina out rear-side adjustment.
1.Set the maintenance mode U411, select DP Auto Adj and press the 5.If OK appears on the display, the adjustment is completed.
Start key to print an original. If ERROR XX appears, the adjustment failed. Check the original set
2.Set the printed original on the contact glass and press the Start key. position and repeat steps 2 and 4 until OK appears.
3.Set the original on the DP face up and press the Start key to carry out For details, see the service manual.
surface adjustment.
[Réglage automatique en utilisant l’original pour effectuer le réglage] 4. Placer l'original sur le DP côté imprimé en bas et appuyer sur la touche Start pour
Si la machine n'est pas pourvue de la fonction réglage automatique d'original du DP procéder au réglage du côté arrière.
1. Régler le mode maintenance U411, sélectionner DP Auto Adj et appuyer sur la 5. Si le message OK apparaît sur l'affichage, le réglage est terminé.Si le message
touche Start pour imprimer un original. ERROR XX (erreur XX) s'affiche, le réglage a échoué. Vérififer la position de
2. Placer l'original qui vient d'être imprimé sur la vitre d'exposition et appuyer sur la l'original et recommencer les opérations 2 et 4 jusqu'à ce que le message OK
touche Start. apparaisse.
3. Placer l'original sur le DP côté imprimé en haut et appuyer sur la touche Start Pour plus de details, se reporter au manuel d’entretien.
pour procéder au réglage de la surface.
[Ajuste automático utilizando el original para el ajuste] 4. Coloque el original en el DP cara abajo y pulse la tecla de Start para realizar un
Si no existe el original de ajuste automático del DP ajuste de reverso.
1. Entre al modo de mantenimiento U441, seleccione DP Auto Adj y pulse la tecla 5. Wenn am Display OK angezeigt wird, ist die Einstellung abgeschlossen. Wenn
de Start para imprimir un original. ERROR XX (FEHLER XX) angezeigt wird, ist die Einstellung fehlgeschlagen.
2. Coloque el original impreso sobre el cristal de contacto y pulse la tecla de Start. Überprüfen Sie die Originalpositionierung und wiederholen Sie Schritte 2 und 4,
3. Coloque el original en el DP cara arriba y pulse la tecla de Start para realizar un bis OK angezeigt wird.
ajuste de anverso. Weitere Einzelheiten siehe Wartungsanleitung.
[Automatische Einstellung mithilfe des Originals] 4. Das Original mit der Druckseite nach unten einlegen und die Start-Taste betäti-
Falls keine automatische Einstellung des Originals des DP vorhanden ist gen, um die Rückseiteneinstellung ausführen zu lassen.
1. Den Wartungsmodus U411 einschalten. DP Auto Adj wählen und die Start-Taste 5. Wenn am Display OK angezeigt wird, ist die Einstellung abgeschlossen. Wenn
betätigen, um ein Original auszudrucken. ERROR XX (FEHLER XX) angezeigt wird, ist die Einstellung fehlgeschlagen.
2. Das ausgedruckte Original auf das Kontaktglas legen und die Start-Taste betäti- Überprüfen Sie die Originalpositionierung und wiederholen Sie Schritte 2 und 4,
gen. bis OK angezeigt wird.
3. Das Original mit der Druckseite nach oben einlegen und die Start-Taste betäti- Weitere Einzelheiten siehe Wartungsanleitung.
gen, um die Oberflächeneinstellung ausführen zu lassen
[Regolazione automatica eseguita con l’originale] 4. Posizionare l'originale sul DP rivolto verso il basso e premere il tasto di Start per
Se non è presente l'autoregolazione originale DP eseguire la regolazione del lato posteriore.
1. Impostare la modalità manutenzione U411, selezionare DP Auto Adj e premere il 5. Se OK appare sul display, la regolazione è completata.Se compare ERROR XX
tasto di Start per stampare un originale. (ERRORE XX), la regolazione non è riuscita. Verificare la posizione di impostazi-
2. Posizionare l'originale stampato sul vetro di appoggio e premere il tasto di Start. one dell'originale e ripetere le operazioni 2 e 4
3. Posizionare l'originale sul DP rivolto verso l'alto e premere il tasto di Start per fino a quando appare OK.
eseguire la regolazione della superficie. Per ulteriori dettagli leggere il manuale d’istruzioni.
[ 通过调整用原稿进行自动调整 ] 4.将原稿面朝下放在 DP 主机上，按 Start 键以进行反面的调整。

没有 DP 调整用原稿时 5.如果屏幕上出现 OK（完成），则表示调整完成。
1.设置维护模式 U411，按 DP Auto Adj、Start 键以输出原稿。如果出现 ERROR XX（错误 XX），则表示调整失败。检查原稿设定位置并
2.将输出的原稿放在稿台上，按 Start 键。重复步骤 2 和 4，直到 OK（完成）出现。
3.将原稿面朝上放在 DP 主机上，按 Start 键以进行正面的调整。详细内容请参照维修手册。
[ 조정용 원고에 읳나 자동조정 ] 4.원고를 FaceDown 으로 DP 본체에 장착하고 시작키를 눌러 뒷면조정

DP 조정용 원고가 없는 경우 을 합니다 .
1. 메인터넌스 모드 U411 을 세트하고 DP Auto Adj, 시작키를 눌러 원고를 출 5.디스플레이에 OK 가 표시되면 조정완료가 됩니다 .
력합니다 . ERROR XX 가 표시된 경우에는 조정실패입니다 . 원고 장착위치를 확
2. 출력한 원고를 원고 유리에 장착하고 시작키를 누릅니다 . 인하고 OK 가 표시될 때까지 순서 2 ～ 4 를 반복합니다 .
3. 원고를 FaceUp 으로 DP 본체로 세트하고 시작키를 눌러 표면조정을 합니 상세는 서비스 매뉴얼을 참조
다.
[ 調整用原稿による自動調整 ] 4.原稿を FaceDown で DP 本体へセットし、Start キーを押し、

裏面の調整
DP 調整用原稿が無い場合を行う。
1.メンテナンスモード U411 をセットし、DP Auto Adj、 Start キーを押し 5.ディスプレイに OK が表示されれば調整完了となる。
原稿を出力する。 ERROR XX が表示された場合は調整失敗である。原稿のセット位置を確
2.出力した原稿をコンタクトガラス上にセットし、Start キーを押す。認し、OK が表示されるまで手順 2 ～ 4 を繰り返す。
3.原稿を FaceUp で DP 本体へセットし、Start キーを押し、表面の調整を詳細はサービスマニュアルを参照のこと。
行う。
23
5mm
F 149 1mm
A(149 5mm)
R 74 1mm
Using a DP auto adjustment original 3.If OK appears on the display, the adjustment is completed.
1.Direct F and R of the DP auto adjustment original upward, and set the If ERROR XX appears, the adjustment failed. Check the original set
original from the place where F and R are marked position and repeat steps 1 and 2 until OK appears.
2.Set the maintenance mode U411. Press the DP FaceUp (Chart2), Input For details, see the service manual.
and the Start key in that order to carry out surface adjustment.
Avec la fonction réglage automatique d'original du DP 3.Si le message OK apparaît sur l'affichage, le réglage est terminé.Si le
1.Diriger F (avant) et R (arrière) de la fonction de réglage automatique message ERROR XX (erreur XX) s'affiche, le réglage a échoué. Vérifi-
d’original du DP vers le haut, puis placer l’original à partir de l’emplace- fer la position de l'original et recommencer les opérations 1 et 2 jusqu'à
ment des repères F et R. ce que le message OK apparaisse.
2.Passer au mode maintenance U411. Appuyer sur les touches DP Pour plus de details, se reporter au manuel d’entretien.
FaceUp (Chart2), Input et Start dans cet ordre pour procéder au
réglage de la surface.
Uso del original de ajuste automático del DP 3.Si aparece OK en la pantalla significa que el ajuste ha sido realizado.
1.Dirija F y R del original de ajuste automático del DP hacia arriba, y Si aparece ERROR XX, el ajuste ha fallado. Compruebe la posición
coloque el original a partir del sitio en que están marcados F y R. ajustada del original y repita los pasos 1 y 2 hasta que aparezca OK en
2.Entre en el modo de mantenimiento U411. Pulse las teclas DP FaceUp la pantalla.
(Chart2), Input y la tecla de Start, en ese orden, para realizar el ajuste Para mas detalles, lea el manual de servicio.
de anverso.
Gebrauch der automatischen Einstellung des Originals des DP 3.Wenn am Display OK angezeigt wird, ist die Einstellung abgeschlos-
1.F und R der automatischen Einstellung des Originals des DP nach sen. Wenn ERROR XX (FEHLER XX) angezeigt wird, ist die Einstel-
oben zeigen und das Original an die mit F und R markierte Stelle set- lung fehlgeschlagen. Überprüfen Sie die Originalpositionierung und
zen. wiederholen Sie Schritte 1 und 2, bis OK angezeigt wird.
2.Den Wartungsmodus U411 einschalten. DP Faceup (Chart2), Input Weitere Einzelheiten siehe Wartungsanleitung.
und die Start-Taste in dieser Reihenfolge betätigen, um die Oberfläche-
neinstellung ausführen zu lassen.
Uso di un'autoregolazione originale DP 3.Se OK appare sul display, la regolazione è completata.Se compare
1.Orientare F e R dell’autoregolazione originale DP verso l’alto e dis- ERROR XX (ERRORE XX), la regolazione non è riuscita. Verificare la
porre l’originale rispetto ai punti in cui sono contrassegnati F e R. posizione di impostazione dell'originale e ripetere le operazioni 1 e 2
2.Impostare la modalità manutenzione U411. Premere nell'ordine DP fino a quando appare OK.
FaceUp (Chart2), Input e il tasto di Start, per eseguire la regolazione Per ulteriori dettagli leggere il manuale d’istruzioni.
della superficie.
使用 DP 自动调整用稿时 3.如果屏幕上出现 OK（完成），则表示调整完成。

1.将 DP 自动调整原稿的 F 和 R 向上，并把标有 F 和 R 的一侧插入 DP 来设如果出现 ERROR XX（错误 XX），则表示调整失败。检查原稿设定位置并
定原稿。重复步骤 1 和 2，直到 OK（完成）出现。
2.设置维护模式 U411，按顺序按 DP FaceUp(Chart2)、Input、Start 键以详细内容请参照维修手册。
进行正面的调整。
DP 자동조정용 원고를 사용하는 경우 3.디스플레이에 OK 가 표시되면 조정완료가 됩니다 .

1.DP 자동조정원고 F, R 을 위로 향하게 하고 F, R 이 쓰여져 있는 쪽에 ERROR XX 가 표시된 경우에는 조정실패입니다 . 원고 장착위치를 확
서 DP 본체로 세트합니다 . 인하고 OK 가 표시될 때까지 순서 1 ～ 2 를 반복합니다 .
2.메인터넌스 모드 U411 을 세트하고 DP FaceUp(Chart2), Input, 시작 상세는 서비스 매뉴얼을 참조
키의 순서로 눌러 표면 조정을 합니다 .
DP 自動調整原稿を使用する場合 3.ディスプレイに OK が表示されれば調整完了となる。

1.DP 自動調整原稿の F、R を上に向け、F、
R が書かれている方から DP 本体 ERROR XX が表示された場合は調整失敗である。原稿のセット位置を確
へセットする。認し、OK が表示されるまで手順 1 ～ 2 を繰り返す
2.メンテナンスモード U411 をセットし、DP FaceUp(Chart2)、Input、詳細はサービスマニュアルを参照のこと。
Start キーの順に押し、表面の調整を行う。
24
5mm
F 149 1mm
A(149 5mm)
R 74 1mm
4.After completing the surface adjustment, direct F and R of the DP auto 6.If OK appears on the display, the adjustment is completed.
adjustment original downward and set the original by inserting the side If ERROR XX appears, the adjustment failed. Check the original set
where the F and R are marked into the DP first. position and repeat steps 4 and 5 until OK appears.
5. Set the maintenance mode U411. Press the DP FaceDown (Chart2), For details, see the service manual.
Normal Target, Input and the Start key in that order to carry out rear-
side adjustment.
4. Une fois le réglage de la surface effectué, diriger F (avant) et R 6.Si le message OK apparaît sur l'affichage, le réglage est terminé. Si le
(arrière) de la fonction de réglage automatique d’original du DP vers le message ERROR XX (erreur XX) s'affiche, le réglage a échoué. Vérifi-
bas et placer l’original en introduisant en premier dans le DP le côté sur fer la position de l'original et recommencer les opérations 4 et 5 jusqu'à
lequel F et R sont indiqués. ce que le message OK apparaisse.
5.Passer au mode maintenance U411. Appuyer sur les touches DP
Pour plus de details, se reporter au manuel d’entretien.
FaceDown (Chart2), Normal Target, Input et Start dans cet ordre pour
procéder au réglage du côté arrière.
4.Una vez hecho el ajuste del anverso, dirija F y R del original de ajuste 6.Si aparece OK en la pantalla significa que el ajuste ha sido realizado.
automático del DP hacia abajo y coloque el original insertando en el Si aparece ERROR XX, el ajuste ha fallado. Compruebe la posición
DP, en primer lugar, el lado en el que están marcados F y R. ajustada del original y repita los pasos 4 y 5 hasta que aparezca OK en
5.Entre en el modo de mantenimiento U411. Pulse las teclas DP Face- la pantalla.
Down (Chart2), Normal Target, Input y la tecla de Start, en ese orden, Para mas detalles, lea el manual de servicio.
para realizar el ajuste de reverso.
4.Nach dem Abschluss der Oberflächeneinstellung F und R der automa- 6.Wenn am Display OK angezeigt wird, ist die Einstellung abgeschlos-
tischen Einstellung des Originals des DP nach unten zeigen und das sen.Wenn ERROR XX (FEHLER XX) angezeigt wird, ist die Einstel-
Original einstellen, indem die mit F und R markierte Seite zuerst in den lung fehlgeschlagen. Überprüfen Sie die Originalpositionierung und
DP eingeführt wird. wiederholen Sie Schritte 4 und 5, bis OK angezeigt wird.
5.Den Wartungsmodus U411 einschalten. DP FaceDown (Chart2), Nor- Weitere Einzelheiten siehe Wartungsanleitung.
mal Target, Input und die Start-Taste in dieser Reihenfolge betätigen,
um die Rückseiteneinstellung ausführen zu lassen.
4.Una volta conclusa la regolazione della superficie, orientare F e R 6.Se OK appare sul display, la regolazione è completata.Se compare
dell’autoregolazione originale DP verso il basso e disporre l’originale ERROR XX (ERRORE XX), la regolazione non è riuscita. Verificare la
inserendo nel DP prima il lato su cui sono contrassegnati F e R. posizione di impostazione dell'originale e ripetere le operazioni 4 e 5
5.Impostare la modalità manutenzione U411. Premere nell'ordine DP fino a quando appare OK.
FaceDown (Chart2), Normal Target, Input e il tasto di Start, per Per ulteriori dettagli leggere il manuale d’istruzioni.
eseguire la regolazione del lato posteriore.
4.完成正面调整后，将 DP 自动调整原稿的 F 和 R 向下，并首先将标有 F 和 6.如果屏幕上出现 OK（完成），则表示调整完成。

R 的一侧插入 DP 来设定原稿。如果出现 ERROR XX（错误 XX），则表示调整失败。检查原稿设定位置并
5.设置维护模式 U411，按顺序按 DP FaceDown(Chart2)、Normal Taget、重复步骤 4 和 5，直到 OK（完成）出现。
Input、Start 键以进行反面的调整。详细内容请参照维修手册。
4.표면의 조정완료 후 DP 자동조정원고의 F, R 을 아래로 향하게 해 F, R 6.디스플레이에 OK 가 표시되면 조정완료가 됩니다 .

이 쓰여져 있는 쪽에서 DP 본체로 세트합니다 . ERROR XX 가 표시된 경우에는 조정실패입니다 . 원고 장착위치를 확
5.메인터넌스 모드 U411 을 세트하고 DP FaceDown(Chart2), Normal 인하고 OK 가 표시될 때까지 순서 4 ～ 5 를 반복합니다 .
Taget, Input, 시작키 순서로 뒷면조정을 합니다 . 상세는 서비스 매뉴얼을 참조
4.表面の調整完了後、 DP 自動調整原稿の F、R を下に向け、

F、R が書かれて 6.ディスプレイに OK が表示されれば調整完了となる。
いる方から DP 本体へセットする。 ERROR XX が表示された場合は調整失敗である。原稿のセット位置を確
5.メンテナンスモード U411 をセットし、DP FaceDown(Chart2)、 Normal 認し、OK が表示されるまで手順 4 ～ 5 を繰り返す。
Taget、Input、Start キーの順に押し、裏面の調整を行う。詳細はサービスマニュアルを参照のこと。
25
X X'
X' X
3 3
X' X
X 2 X' 2
1
a h i j k
X X'
-1.5% 100 +1.5%
X
[Checking the magnification] 2. Use the maintenance mode U070 to adjust the magnification.
1.Check the gap between line (1) of original (a) and line (2) (3) of copy Main Scan: Adjusts the scanner main-scan magnification
example. If the gap exceeds the reference value, adjust the gap Sub Scan: Adjusts the scanner sub-scan magnificationSub
according to the following procedure. Scan (CIS): Adjusts the scanner CIS sub-scan magnification (DP-771)
<Reference value>
For the sub-scan direction, vertical gap of line (2): within ±1.5%
For the main-scan direction, horizontal gap of line (3): within ±1.5%
[Vérification de l’agrandissement] Pour la direction du balayage principal, l’écart horizontal de la ligne (3) est
1. Vérifier l’écart entre la ligne (1) de l’original (a) et la ligne (2) (3) de l’exem- de ±1,5%
ple de copie. Si l’écart excède la valeur de référence, le régler selon la 2. Pour régler l'agrandissement, utilisez le mode entretien U070.
procédure suivante. Main Scan: Permet de régler l'agrandissement du balayage principal du scanner
<Valeur de référence> Sub Scan: Permet de régler l'agrandissement du balayage secondaire du scanner
Pour la direction du balayage secondaire, l’écart vertical de la ligne (2) est Sub Scan (CIS): Permet de régler l'agrandissement du balayage secon-
de ±1,5% daire du CIS du scanner (DP-771)
[Verificación del cambio de tamaño] 2.Para ajustar la ampliación utilice el modo de mantenimiento U070.
1.Compruebe la separación entre la línea (1) del original (a) y la línea (2) Main Scan: ajusta el cambio de tamaño de la dirección de exploración
(3) del ejemplo de copia. Si la separación supera el valor de referencia, principal del escáner.
ajústela siguiendo este procedimiento. Sub Scan: ajusta el cambio de tamaño de la dirección de exploración
<Valor de referencia> secundaria del escáner.
Para la dirección de exploración secundaria, separación vertical de la línea (2): dentro de ±1,5% Sub Scan (CIS): ajusta el cambio de tamaño de la dirección de explor-
Para la dirección de exploración principal, separación horizontal de la línea (3): dentro de ±1,5% ación secundaria CIS del escáner (DP-771).
[Überprüfen der Vergrößerung] 2.Zum Einstellen der Vergrößerung den Wartungsmodus U070
1.Den Abstand zwischen der Linie (1) des Originals (a) und der Linie (2) verwenden.
(3) des Kopierbeispiels prüfen. Wenn der Abstand größer als der Main Scan: Zur Einstellung der Hauptscan-Vergrößerung
Bezugswert ist, den Abstand mit dem folgenden Verfahren einstellen. Sub Scan: Zur Einstellung der Subscan-Vergrößerung
<Bezugswert> Sub Scan (CIS): Zur Einstellung der Scanner-CIS-Subscan-Vergrößer-
Subscanrichtung: Vertikaler Abstand der Linie (2): Innerhalb ±1,5% ung (DP-771)
Hauptscanrichtung: Horizontaler Abstand der Linie (3): Innerhalb ±1,5%
[Controllo dell’ingrandimento] Per l’orientamento della scansione principale, lo scostamento orizzontale

1. Verificare lo scostamento fra la linea (1) dell’originale (a) e la linea (2) (3) della linea (3) deve essere compreso fra ±1,5%
dell’esempio di copia. Se lo scostamento supera il valore di riferimento, 2. Usare la modalità di manutenzione U070 per regolare l'ingrandimento.
regolare lo scostamento stesso seguendo questa procedura. Main Scan: Regola l'ingrandimento della scansione principale dello scanner
<Valore di riferimento> Sub Scan: Regola l'ingrandimento della scansione ausiliare dello scanner
Per l’orientamento della scansione ausiliare, lo scostamento verticale della Sub Scan (CIS): Regola l'ingrandimento della scansione ausiliare CIS dello
linea (2) deve essere compreso fra ±1,5% scanner (DP-771)
[ 确认等倍值 ] 2.使用维修模式 U070 调整等倍值。

1.确认原稿（a）上的线（1）和复印样本上的线（2）、（3）之间的偏移值。 Main Scan ：读取主扫描等倍度的调整
如果偏移值超过标准值，则按照下列步骤进行调整。 Sub Scan ：读取副扫描等倍度的调整
< 标准值 > Sub Scan(CIS) ：CIS 的读取副扫描等倍度的调整 (DP-771)
对于副扫描方向，线（2）的上下偏移值：±1.5% 以内
对于主扫描方向，线（3）的左右偏移值：±1.5% 以内
[ 등배도확인 ] 2.메인터넌스 모드 U070 을 세트하고 조정을 합니다 .

1.원고 (a) 선 (1) 과 복사샘플의 선 (2)(3) 의 차이를 확인합니다 . Main Scan：스캔 주사등배도의 조정
차이가 기준이외의 경우 , 다음 순서로 조정을 합니다 . Sub Scan：스캔 부주사등배도의 조정
＜기준치＞ Sub Scan(CIS)：CIS 의 스캔 부주사등배도의 조정 (DP-771)
부주사 방향의 경우 선 (2) 의 상하차이：±1.5% 이내
주주사 방향의 경우 선 (3) 의 좌우차이：±1.5% 이내
[ 等倍度確認 ] 2.メンテナンスモード U070 をセットし、調整を行う。

1.原稿 (a) の線 (1) とコピーサンプルの線 (2)(3) のずれを確認する。 Main Scan：読み取り主走査等倍度の調整
ずれが基準値外の場合、次の手順で調整を行う。 Sub Scan：読み取り副走査等倍度の調整
＜基準値＞ Sub Scan(CIS)：CIS の読み取り副走査等倍度の調整 (DP-771)
副走査方向の場合、線 (2) の上下ずれ：±1.5% 以内
主走査方向の場合、線 (3) の左右ずれ：±1.5% 以内
26
X X'
X' X
3 3
X' X
X 2 X' 2
1
a h i j k
X X'
-1.5% 100 +1.5%
X
3. Adjust the values. 5. Repeat the steps 2 to 4 above until the gap of line (2) (3) of copy
For the shorter length copy example (h)(j): Increases the value. example shows the reference value.
For the longer length copy example (i)(k): Decreases the value. <Reference value>
Amount of change per step: 0.10 % For the sub-scan direction, vertical gap of line (2): within ±1.5%
4.Perform a test copy. For the main-scan direction, horizontal gap of line (3): within ±1.5%
3.Régler les valeurs. 5.Répéter les étapes 2 à 4 jusqu’à ce que l’écart de la ligne (2) (3) de
Pour l’exemple de copie dont la longueur est plus courte (h)(j) : l’exemple de copie indique la valeur de référence.
augmenter la valeur. <Valeur de référence>
Pour l’exemple de copie dont la longueur est plus longue (i)(k) : Pour la direction du balayage secondaire, l’écart vertical de la ligne (2)
diminuer la valeur. est de ±1,5%
Changement par graduation d’échelle : 0.10 % Pour la direction du balayage principal, l’écart horizontal de la ligne (3)
4.Effectuer une copie de test. est de ±1,5%
3.Ajuste los valores. 5.Repita los pasos 2 a 4 anteriores hasta que la separación de la línea
Para el ejemplo de copia más corto (h)(j): aumenta el valor. (2) (3) del ejemplo de copia presente el valor de referencia.
Para el ejemplo de copia más largo (i)(k): disminuye el valor. <Valor de referencia>
Magnitud del cambio por incremento: 0.10 % Para la dirección de exploración secundaria, separación vertical de la
4.Haga una copia de prueba. línea (2): dentro de ±1,5%
Para la dirección de exploración principal, separación horizontal de la
línea (3): dentro de ±1,5%
3.Die Werte einstellen. 5.Die Schritte 2 bis 4 wiederholen, bis der Abstand der Linie (2) (3) des
Für die kürzere Länge des Kopierbeispiels (h)(j): Den Wert erhöhen. Kopierbeispiels den Bezugswert aufweist.
Für die längere Länge des Kopierbeispiels (i)(k): Den Wert verringern. <Bezugswert>
Änderung pro Schritt: 0.10 % Subscanrichtung: Vertikaler Abstand der Linie (2): Innerhalb ±1,5%
4.Eine Testkopie erstellen. Hauptscanrichtung: Horizontaler Abstand der Linie (3): Innerhalb
±1,5%
3.Regolare i valori. 5.Ripetere le operazioni sopra descritte da 2 a 4 fino a quando lo scostamento

Per l’esempio di copia di lunghezza inferiore (h)(j): aumenta il valore. della linea (2) (3) dell’esempio di copia riporterà i valori di riferimento.
Per l’esempio di copia di lunghezza superiore (i)(k): riduce il valore. <Valore di riferimento>
Entità modifica per passo: 0,10 % Per l’orientamento della scansione ausiliare, lo scostamento verticale
4.Eseguire una copia di prova della linea (2) deve essere compreso fra ±1,5%
Per l’orientamento della scansione principale, lo scostamento orizzon-
tale della linea (3) deve essere compreso fra ±1,5%
3.调整设定值。 5.重复上述步骤 2 到 4，直至复印样本上的线（2）、（3）之间的偏移值达

在长度偏短时复印样本（h）（j）：调高设定值到标准值范围内。
在长度偏长时复印样本（i）（k）：调低设定值 < 标准值 >
设定值的一个调整单位变化量：0.10% 对于副扫描方向，线（2）的上下偏移值：±1.5% 以内
4.进行测试复印。对于主扫描方向，线（3）的左右偏移值：±1.5% 以内
3.설정치를 조정합니다 . 5.복사샘플 선 (2)(3) 의 차이가 기준치내가 될 때까지 2 ～ 4 를 반복합니

길이가 짧은 경우 복사샘플 (h)(j)：설정치를 높입니다 . 다.
길이가 긴 경우 복사샘플 (i)(k)：설정치를 내립니다 . ＜기준치＞
1 스텝당 변화량：0.10% 부주사 방향의 경우 선 (2) 의 상하차이：±1.5% 이내
4.시험복사를 합니다 . 주주사 방향의 경우 선 (3) 의 좌우차이：±1.5% 이내
3.設定値を調整する。 5.コピーサンプルの線 (2)(3) のずれが基準値内になるまで手順 2 ～ 4

長さが短い場合コピーサンプル (h)(j)：設定値を上げるを繰り返す。
長さが長い場合コピーサンプル (i)(k)：設定値を下げる＜基準値＞
1 ステップ当たりの変化量：0.10% 副走査方向の場合、線 (2) の上下ずれ：±1.5% 以内
4.テストコピーを行う。主走査方向の場合、線 (3) の左右ずれ：±1.5% 以内
27
2.5mm
2.5mm
1 2
a l m
[Checking the leading edge timing] 2. Use the maintenance mode U071 to adjust the timing.
1.Check the gap between line (1) on original (a) and line (2) of copy Front Head: Adjusts the leading edge timing (surface)
example. If the gap exceeds the reference value, adjust the gap Front Tail: Adjusts the trailing edge timing (surface)
according to the following procedure. CIS Head: Adjusts the leading edge timing for CIS scanning.
<Reference value> CIS Tail: Adjusts the trailing edge timing for CIS scanning.
Vertical gap of line (2): within ±2.5 mm
[Vérification de la synchronisation du bord avant] 2. Pour régler la synchronisation, utilisez le mode entretien U071.
1.Vérifier l’écart entre la ligne (1) de l’original (a) et la ligne (2) de l’exem- Front Head: Permet de régler la synchronisation du bord de tête (surface)
ple de copie. Si l’écart excède la valeur de référence, le régler selon la Front Tail: Permet de régler la synchronisation du bord arrière (surface)
procédure suivante. CIS Head: Permet de régler la synchronisation du bord de tête pour le
<Valeur de référence> balayage par le CIS.
Écart vertical de la ligne (2) : ±2.5 mm CIS Tail: Permet de régler la synchronisation du bord arrière pour le balay-
age par le CIS.
[Cambio de la sincronización de borde superior] 2.Para ajustar la sincronización utilice el modo de mantenimiento U071.
1.Compruebe la separación entre la línea (1) del original (a) y la línea (2) Front Head: ajusta la sincronización del borde superior (anverso).
del ejemplo de copia. Si la separación supera el valor de referencia, Front Tail: ajusta la sincronización del borde inferior (anverso).
ajústela siguiendo este procedimiento. CIS Head: ajusta la sincronización del borde superior para exploración CIS.
<Valor de referencia> CIS Tail: ajusta la sincronización del borde inferior para exploración CIS.
Separación vertical de la línea (2): dentro de ±2,5 mm
[Überprüfen des Vorderkanten-Timings] 2.Zum Einstellen des Timing den Wartungsmodus U071 verwenden.
1.Den Abstand zwischen der Linie (1) des Originals (a) und der Linie (2) Front Head: Zur Einstellung des Vorderkanten-Timing (Oberfläche)
des Kopierbeispiels prüfen. Wenn der Abstand größer als der Front Tail: Zur Einstellung des Hinterkanten-Timing (Oberfläche)
Bezugswert ist, den Abstand mit dem folgenden Verfahren einstellen. CIS Head: Zur Einstellung des Vorderkanten-Timing für CIS-Scannen.
<Bezugswert> CIS Tail: Zur Einstellung des Hinterkanten-Timing für CIS-Scannen.
Vertikaler Abstand der Linie (2): Innerhalb ±2,5 mm
[Controllo della sincronizzazione del bordo principale] 2.Usare la modalità di manutenzione U071 per regolare la
1.Verificare lo scostamento fra la linea (1) sull’originale (a) e la linea (2) sincronizzazione.
dell’esempio di copia. Se lo scostamento supera il valore di riferimento, Front Head: Regola la sincronizzazione del bordo principale (superficie)
regolare lo scostamento stesso seguendo questa procedura. Front Tail: Regola la sincronizzazione del bordo di uscita (superficie)
<Valore di riferimento> CIS Head: Regola la sincronizzazione del bordo principale per scan-
Scostamento verticale della linea (2) compreso fra ±2,5 mm sione CIS.
CIS Tail: Regola la sincronizzazione del bordo di uscita per scansione CIS.
[ 确认前端定时调整 ] 2.使用维修模式 U071 调整定时。

1.确认原稿（a）上的线（1）和复印样本上的线（2）之间的偏移值。如果偏 Front Head ：调整前端对位 ( 正面 )
移值超过标准值，则按照下列步骤进行调整。 Front Tail ：调整后端对位 ( 正面 )
< 标准值 > CIS Head ：调整 CIS 读取时的前段对位
线（2）的上下偏移值：±2.5mm 以内 CIS Tail ：调整 CIS 读取时的后端对位
[ 선단 타이밍확인 ] 2.메인터넌스 모드 U071 을 세트하고 조정을 합니다 .

1.원고 (a) 선 (1) 과 복사샘플 선 (2) 의 차이를 확인합니다 . 차이가 기준 Front Head ：선단 타이밍 ( 표면 ) 을 조정합니다 .
치 외의 경우 다음 순서로 조정을 합니다 . Front Tail ：후단 타이밍 ( 표면 ) 을 조정합니다 .
＜기준치＞ CIS Head： CIS 스캔 시의 선단 타이밍을 조정합니다 .
선 (2) 의 상하차이：±2.5mm 이내 CIS Tail： CIS 스캔 시의 후단 타이밍을 조정합니다 .
[ 先端タイミング確認 ] 2.メンテナンスモード U071 をセットし、調整を行う。

1.原稿 (a) の線 (1) とコピーサンプルの線 (2) のずれを確認する。ずれ Front Head ：先端タイミング ( 表面 ) を調整する
が基準値外の場合、次の手順で調整を行う。 Front Tail ：後端タイミング ( 表面 ) を調整する
＜基準値＞ CIS Head： CIS 読み込み時の先端タイミングを調整する
線 (2) の上下ずれ：±2.5mm 以内 CIS Tail： CIS 読み込み時の後端タイミングを調整する
28
2.5mm
2.5mm
1 2
a l m
3.Adjust the values. 5.Repeat the steps 2 to 4 above until the gap of line (2) of copy example
For the faster leading edge timing, copy examples (l): Decreases the shows the reference value.
value. <Reference value>
For the slower leading edge timing, copy examples (m): Increases the Vertical gap of line (2): within ±2.5 mm
value.
Amount of change per step: 0.17 mm
4. Perform a test copy.
3.Régler les valeurs. 5.Répéter les étapes 2 à 4 jusqu’à ce que l’écart de la ligne (2) de
Pour les exemples de copie dont la synchronisation du bord avant est l’exemple de copie indique la valeur de référence.
plus rapide (l) : diminuer la valeur. <Valeur de référence>
Pour les exemples de copie dont la synchronisation du bord avant est Écart vertical de la ligne (2) : ±2.5 mm
plus lente (m) : augmenter la valeur.
Changement par graduation d’échelle : 0,17 mm
4.Effectuer une copie de test.
Para una sincronización más rápida de extremo guía, ejemplos de (2) del ejemplo de copia presente el valor de referencia.
copia (l): disminuye el valor. <Valor de referencia>
Para una sincronización más lenta de extremo guía, ejemplos de copia Separación vertical de la línea (2): dentro de ±2,5 mm
(m): aumenta el valor.
Magnitud del cambio por incremento: 0,17 mm
4.Haga una copia de prueba.
3.Die Werte einstellen. 5.Die Schritte 2 bis 4 wiederholen, bis der Abstand der Linie (2) des
Für den schnelleren Vorderkantentakt, Kopierbeispiel (l): Den Wert ver- Kopierbeispiels den Bezugswert aufweist.
ringern. <Bezugswert>
Für den langsameren Vorderkantentakt, Kopierbeispiel (m): Den Wert Vertikaler Abstand der Linie (2): Innerhalb ±2,5 mm
erhöhen.
Änderung pro Schritt: 0,17 mm
4.Eine Testkopie erstellen.
3.Regolare i valori. 5.Ripetere le operazioni sopra descritte da 2 a 4 fino a quando lo scosta-

Per accelerare la fasatura del bordo di entrata, esempi di copia (l): mento della linea (2) dell’esempio di copia riporterà i valori di riferi-
riduce il valore. mento.
Per rallentare la fasatura del bordo di entrata, esempi di copia (m): <Valore di riferimento>
aumenta il valore. Scostamento verticale della linea (2) compreso fra ±2,5 mm
Entità modifica per passo: 0,17 mm
4.Eseguire una copia di prova
3.调整设定值。 5.重复上述步骤 2 到 4，直至复印样本上的线（2）的偏移值达到标准值范

在前端定时偏快时复印样本（l）：调低设定值围内。
在前端定时偏慢时复印样本（m）：调高设定值 < 标准值 >
设定值的一个调整单位变化量：0.17mm 线（2）的上下偏移值：±2.5mm 以内
3.설정치를 조정합니다 . 5.복사샘플 선 (2) 의 차이가 기준치내가 될 때까지 2 ～ 4 를 반복합니다 .

선단 타이밍이 빠른 경우 복사샘플 (l)：설정치를 내립니다 . ＜기준치＞
선단 타이밍이 늦은 경우 복사샘플 (m)：설정치를 올립니다 . 선 (2) 의 상하차이：±2.5mm 이내
1 스텝당 변화량：0.17mm
3.設定値を調整する。 5.コピーサンプルの線 (2) のずれが基準値内になるまで手順 2 ～ 4 を繰

先端タイミングが早い場合コピーサンプル (l)：設定値を下げる。り返す。
先端タイミングが遅い場合コピーサンプル (m)：設定値を上げる。＜基準値＞
1 ステップ当たりの変化量：0.17mm 線 (2) の上下ずれ：±2.5mm 以内
29
2mm/3mm 2mm/3mm
1 2 2
a n o
[Checking the center line] 2.Use the maintenance mode U072 to adjust the timing.
1.Check the gap between center line (1) on original (a) and center line Front: Adjusts the center line (surface)
(2) of copy example. If the gap exceeds the reference value, adjust the Back: Adjusts the center line (rear side)
gap according to the following procedure. CIS: Adjusts the CIS center line
<Reference value>
Horizontal difference of center line (2) for the single copying: ±2.0 mm
Horizontal difference of center line (2) for the duplex copying: ±3.0 mm
[Vérification de la ligne médiane] 2.Pour régler la ligne médiane, utiliser le mode entretien U072.
1.Vérifier l’écart entre l’axe (1) de l’original (a) et l’axe (2) de l’exemple de Front: Permet de régler l'axe (surface)
copie. Si l’écart excède la valeur de référence, le régler selon la procé- Back: Permet de régler l'axe (arrière)
dure suivante. CIS: Permet de régler l'axe du CIS
<Valeur de référence>
Différence horizontale de l’axe (2) pour la copie recto : ±2.0 mm
Différence horizontale de l’axe (2) pour la copie recto-verso : ±3.0 mm
[Verificación de la línea central] Diferencia horizontal de la línea de centro (2) para el copiado dúplex:
1.Compruebe la separación entre la línea de centro (1) del original (a) y ±3.0 mm
la línea de centro (2) del ejemplo de copia. Si la separación supera el 2.Para ajustar la línea central utilice el modo de mantenimiento U072.
valor de referencia, ajústela siguiendo este procedimiento. Front: ajusta la línea central (anverso).
<Valor de referencia> Back: ajusta la línea central (reverso).
Diferencia horizontal de la línea de centro (2) para el copiado por una CIS: ajusta la línea central CIS.
cara: ±2.0 mm
[Überprüfen der Mittellinie] 2.Zum Einstellen der Mittellinie den Wartungsmodus U072 verwenden.
1.Den Abstand zwischen der Mittellinie (1) des Originals (a) und der Mit- Front: Zur Einstellung der Mittellinie (Oberfläche)
tellinie (2) des Kopierbeispiels prüfen. Wenn der Abstand größer als der Back: Zur Einstellung der Mittellinie (Rückseite)
Bezugswert ist, den Abstand mit dem folgenden Verfahren einstellen. CIS: Zur Einstellung der CIS-Mittellinie
<Bezugswert>
Horizontaler Unterschied der Mittellinie (2) für die Einzelkopie: ±2.0 mm
Horizontaler Unterschied der Mittellinie (2) für die Duplexkopie: ±3.0 mm
[Controllo della linea centrale] 2.Usare la modalità di manutenzione U072 per regolare la linea centrale.
1.Verificare lo scostamento fra la linea centrale (1) sull’originale (a) e la linea Front: Regola la linea centrale (superficie)
centrale (2) dell’esempio di copia. Se lo scostamento supera il valore di Back: Regola la linea centrale (lato posteriore)
riferimento, regolare lo scostamento stesso seguendo questa procedura. CIS: Regola la linea centrale CIS
<Valore di riferimento>
Differenza orizzontale della linea centrale (2) per la copia singola: ±2.0 mm
Differenza orizzontale della linea centrale (2) per la copia duplex: ±3.0 mm
[ 确认中心线 ] 2.使用维修模式 U072 调整中心线。

1.确认原稿（a）中心线（1）和复印样本中心线（2）之间的偏移值。如果偏 Front：中心位置（正面）的调整
移值超过标准值，则按照下列步骤进行调整。 Back：中心位置（反面）的调整
< 标准值 > 单面复印时，中心线（2）的左右偏移值：±2.0mm 以内 CIS：CIS 的中心位置的调整
　　　　　双面复印时，中心线（2）的左右偏移值：±3.0mm 以内
[ 센터 라인 확인 ] 2.메인터넌스 모드 U072 을 세트하고 조정을 합니다 .

1.원고 (a) 중심선 (1) 과 복사샘플 중심선 (2) 의 차이를 확인합니다 . 차 Front：센터 위치（표면）의 조정
이가 기준치 외의 경우 다음 순서로 조정합니다 . Back：센터 위치（뒷면）의 조정
＜기준치＞단면의 경우 중심선 (2) 의 좌우차이：±2.0mm 이내 CIS：CIS 의 센터 위치조정
양면의 경우 중심선 (2) 의 좌우차이：±3.0mm 이내
[ センターライン確認 ] 2.メンテナンスモード U072 をセットし、

調整を行う。
1.原稿 (a) の中心線 (1) とコピーサンプルの中心線 (2) のずれを確認す Front：センター位置（表面）の調整
る。ずれが基準値外の場合、次の手順で調整を行う。 Back：センター位置（裏面）の調整
＜基準値＞片面の場合、中心線 (2) の左右ずれ：±2.0mm 以内 CIS：CIS のセンター位置の調整
　　　　　両面の場合、中心線 (2) の左右ずれ：±3.0mm 以内
30
2mm/3mm 2mm/3mm
1 2 2
a n o
3. Adjust the values. 5.Repeat the steps 2 to 4 above until the gap of line (2) of copy example
If the center moves more front, copy example (n): Increases the value. shows the reference value.
If the center moves inner, copy sample (o): Decreases the value. <Reference value>
Amount of change per step: 0.085 mm Horizontal difference of center line (2) for the single copying: ±2.0 mm
4. Perform a test copy. Horizontal difference of center line (2) for the duplex copying: ±3.0 mm
3.Régler les valeurs. 5.Répéter les étapes 2 à 4 jusqu’à ce que l’écart de la ligne (2) de
Pour l’exemple de copie (n) dont l’axe se déplace davantage vers l’exemple de copie indique la valeur de référence.
l’avant : augmenter la valeur. <Valeur de référence>
Pour l’exemple de copie (o) dont l’axe se déplace vers l’intérieur : Différence horizontale de l’axe (2) pour la copie recto : ±2.0 mm
diminuer la valeur. Différence horizontale de l’axe (2) pour la copie recto-verso : ±3.0 mm
Changement par graduation d’échelle : 0,085 mm
4.Effectuer une copie de test.
Si el centro se desplaza más hacia el frente, ejemplo de copia (n): (2) del ejemplo de copia presente el valor de referencia.
aumenta el valor. <Valor de referencia>
Si el centro se desplaza hacia dentro, ejemplo de copia (0): disminuye Diferencia horizontal de la línea de centro (2) para el copiado por una
el valor. cara: ±2.0 mm
Magnitud del cambio por incremento: 0,085 mm Diferencia horizontal de la línea de centro (2) para el copiado dúplex:
4.Haga una copia de prueba. ±3.0 mm
3.Die Werte einstellen. 5.Die Schritte 2 bis 4 wiederholen, bis der Abstand der Linie (2) des
Wenn die Mitte nach vorne verlagert ist, Kopierbeispiel (n): Den Wert Kopierbeispiels den Bezugswert aufweist.
erhöhen. <Bezugswert>
Wenn die Mitte nach innen verlagert ist, Kopierbeispiel (o): Den Wert Horizontaler Unterschied der Mittellinie (2) für die Einzelkopie: ±2.0 mm
verringern. Horizontaler Unterschied der Mittellinie (2) für die Duplexkopie: ±3.0 mm
Änderung pro Schritt: 0,085 mm
4.Eine Testkopie erstellen.
3.Regolare i valori. 5.Ripetere le operazioni sopra descritte da 2 a 4 fino a quando lo

Se il centro si sposta più avanti, esempio di copia (n): aumenta il scostamento della linea (2) dell’esempio di copia riporterà i valori di
valore. riferimento.
Se il centro si sposta verso l’interno, esempio di copia (o): riduce il <Valore di riferimento>
valore. Differenza orizzontale della linea centrale (2) per la copia singola: ±2.0 mm
Entità modifica per passo: 0,085 mm Differenza orizzontale della linea centrale (2) per la copia duplex: ±3.0 mm
4.Eseguire una copia di prova
3.调整设定值。 5.重复上述步骤 2 到 4，直至复印样本上的线（2）的偏移值达到标准值范

当中心向前偏移时复印样本（n）：调高设定值围内。
当中心向内偏移时复印样本（o）：调低设定值 < 标准值 >
设定值的一个调整单位变化量：0.085mm 单面复印时，中心线（2）的左右偏移值：±2.0mm 以内
4.进行测试复印。双面复印时，中心线（2）的左右偏移值：±3.0mm 以内
3.설정치를 조정합니다 . 5.복사샘플 중심선 (2) 차이가 기준치 내가 될 때까지 순서 2 ～ 4 를 반복

센터가 바로 앞으로 틀려 있는 경우 복사샘플 (n)：설정치를 높입니다 . 합니다 .
센터가 안으로 틀려 있는 경우 복사샘플 (o) : 설정치를 내립니다 . ＜기준치＞
1 스텝당 변화량：0.085mm 단면의 경우 중심선 (2) 의 죄우차이：±2.0mm 이내
4.시험복사를 합니다 . 양면의 경우 중심선 (2) 의 좌우차이：±3.0mm 이내
3.設定値を調整する。 5.コピーサンプルの中心線 (2) ずれが基準値内になるまで手順 2 ～ 4 を

センターが手前にずれている場合コピーサンプル (n)：設定値を上げ繰り返す。
る。＜基準値＞
センターが奥にずれている場合コピーサンプル (o) 設定値を下げる。片面の場合、中心線 (2) の左右ずれ：±2.0mm 以内
1 ステップ当たりの変化量：0.085mm 両面の場合、中心線 (2) の左右ずれ：±3.0mm 以内
31
PAPER FEEDER
E
B
C G
F
A D I
E. Clamp ........................................................ 1 Be sure to remove any tape and/or cushioning

English
F. Wire cover.................................................. 1 material from supplied parts.
Supplied parts G. Paper size plate ......................................... 2
A. Paper feeder.............................................. 1 H. S Tite screw M4 × 8 ................................... 3
B. Pin ............................................................. 2 I. Paper type plate......................................... 2
C. Retainer ..................................................... 1
D. Intermediate paper conveying unit............. 1
E. Collier......................................................... 1 Veillez à retirer les morceaux de bande adhé-

Français
F. Couvercle de câble .................................... 1 sive et/ou les matériaux de rembourrage des
Pièces fournies G. Plateau de format du papier ...................... 2 pièces fournies.
A. Bureau papier ............................................ 1 H. Vis S Tite M4 × 8 ....................................... 3
B. Broche ....................................................... 2 I. Plaque de type de papier........................... 2
C. Élément de retenue ................................... 1
D. Unité de transport du papier intermédiaire 1
E. Sujetador ................................................... 1 Asegúrese de despegar todas las cintas y/o

Español
F. Cubierta para el cable................................ 1 material amortiguador de las partes suministra-
Partes suministradas G. Placa de tamaño de papel ......................... 2 das.
A. Alimentador de papel................................. 1 H. Tornillo S Tite M4 × 8 ................................. 3
B. Clavija........................................................ 2 I. Placa de tipo de papel ............................... 2
C. Retén ......................................................... 1
D. Unidad de transporte de papel intermedia. 1
E. Klemme...................................................... 1 Entfernen Sie Klebeband und/oder Dämpfungs-

Deutsch
F. Kabelabdeckung ........................................ 1 material vollständig von den mitgelieferten
Gelieferte Teile G. Papierformatplatte ..................................... 2 Teilen.
A. Papiereinzug.............................................. 1 H. S-Tite-Schraube M4 × 8............................. 3
B. Stift............................................................. 2 I. Papiertypplatte........................................... 2
C. Halterung ................................................... 1
D. Eingesetzte Papierfördereinheit ................ 1
E. Morsetto..................................................... 1 Accertarsi di rimuovere tutti i nastri adesivi e/o il

Italiano
F. Coperchio cavi ........................................... 1 materiale di imbottitura dalle parti fornite.
Parti di fornitura G. Piastra formato carta ................................. 2
A. Unità di alimentazione della carta ............. 1 H. Vite S Tite M4 × 8 ...................................... 3
B. Perno ........................................................ 2 I. Piastra tipo carta........................................ 2
C. Fermo ....................................................... 1
D. Unità intermediale di trasporto carta.......... 1
简体中文 E. 夹钳 .................................1 如果附属品上带有固定胶带，缓冲材料时务必揭

F. 电线盖板 .............................1 下。
附属品 G. 纸张尺寸托板 .........................2
A. 供纸工作台........................... 1 H. 紧固型 S 螺丝 M4×8 ....................3
B. 固定插销............................. 2 I. 纸张种类托板 .........................2
C. 安装板............................... 1
D. 中间搬运单元......................... 1
한국어 E. 크램프............................................... 1 동봉품에 고정 테이프 , 완충재가 붙어 있는 경

F. 전선커버............................................ 1 우에는 반드시 제거할 것 .
동봉품 G. 용지크기 플레이트............................... 2
A. 급지대............................................... 1 H. 나사 M4×8S 타이트............................. 3
B. 핀..................................................... 2 I. 용지종류 플레이트............................... 2
C. 부착판............................................... 1
D. 중간반송유니트................................... 1
日本語 E. クランプ .............................1 同梱品に固定テープ、緩衝材が付いている場合

F. 電線カバー ...........................1 は必ず取り外すこと。
同梱品 G. 用紙サイズプレート ...................2
A. ペーパーフィーダー................... 1 H. ビス M4×8S タイト ....................3
B. ピン................................. 2 I. 用紙種類プレート .....................2
C. 取付板............................... 1
D. 中間搬送ユニット..................... 1
1
2 4
1
3
Procedure 1. Pull each cassette out and then remove the 3.Remove the lower paper cassette (3) from
Be sure to turn the MFP main power switch off lift plate stopper (1) from each cassette and the MFP
and disconnect the MFP power plug from the attach it to the storage location (2). 4.Remove the pin (4) and remove the lower
wall outlet before starting to install the paper 2.Gently close each cassette. paper cassette (3) in the MFP.
feeder.
Procédure 1.Tirer chaque tiroir vers l’extérieur puis retirer 3.Retirer le tiroir inférieur (3) du MFP.
Veiller à bien mettre l’interrupteur principal du la butée de plaque d’élévation (1) de chaque 4.Déposer la broche (4) et le tiroir à papier
MFP hors tension et à débrancher la fiche d’ali- tiroir et la fixer à l’emplacement de range- inférieur (3) du MFP.
mentation du MFP de la prise murale avant de ment (2).
commencer l’installation du bureau papier. 2.Refermer progressivement chaque tiroir.
Procedimiento 1. Abra la bandeja y quite el tope de la placa 3.Quite el cajón de papel inferior (3) del MFP.
Asegúrese de apagar el interruptor principal del de elevación (1) de cada bandeja y 4.Quite el clavija (4) y el cajón de papel inferior
MFP y de desconectar el enchufe del MFP del colóquela en su lugar de depósito (2). (3) del MFP.
receptáculo de pared antes de empezar a insta- 2.Cierre suavemente cada bandeja.
lar el alimentador de papel.
Verfahren 1.Die einzelnen Kassetten herausziehen, 3.Nehmen Sie die untere Papierlade (3) vom
Schalten Sie unbedingt den Hauptschalter des dann den Hebeplattenanschlag (1) von jeder MFP ab.
MFP aus, und ziehen Sie den Netzstecker des Kassette entfernen und an der Speicherposi- 4. Die Stift (4) entfernen und die untere Papier-
MFP von der Netzsteckdose ab, bevor Sie mit tion (2) anbringen. lade (3) im MFP abnehmen.
der Installation des Papiereinzugs beginnen. 2.Alle Kassetten sachte schließen.
Procedura 1.Estrarre ciascun cassetto e poi rimuovere il 3.Rimuovere il cassetto inferiore della carta (3)
Prima di dare inizio alla procedura di installazi- fermo della piastra di sollevamento (1) da dall’MFP.
one dell’unità di alimentazione della carta, non ciascun cassetto e fissarlo nella posizione di 4.Rimuovere la perno (4) e quindi rimuovere il
mancare di spegnere l’MFP usando l’interruttore immagazzinaggio (2). cassetto inferiore della carta (3) nell'MFP.
principale di alimentazione e di disinserire la 2.Chiudere delicatamente ciascun cassetto.
spina del cavo di alimentazione dalla presa a
muro della rete elettrica.
安装步骤 1.拉出各供纸盒，拆下各 1 个升降板挡块 (1)， 3.取出 MFP 主机的下部供纸盒 (3)。

安装供纸工作台时，必须先关闭 MFP 主机上的主并安装在保管场所 (2) 上。 4.拆除 1 颗固定插销 (4)，取出 MFP 主机的下部
电源开关，并拔出电源插头后方可进行工作。 2.轻轻地推入各供纸盒。供纸盒 (3)。
설치순서 1.각 카세트를 빼고 리프트판 스토퍼 (1) 각 1 3.MFP 본체의 하단 카세트 (3) 를 꺼냅니다 .
급지대를 설치할 때에는 반드시 MFP 본체의 주 개를 빼내 보관장소 (2) 에 부착합니다 . 4.핀 (4) 1 개를 제거하고 MFP 본체 하단 카세
전원 스위치를 OFF 로 하고 MFP 본체 전원 플 2.각 카세트를 조용히 밀어 넣습니다 . 트 (3) 를 꺼냅니다 .
러그를 빼고 작업을 할 것 .
取付手順 1.各カセットを引き出し、リフト板ストッパー 3.MFP 本体の下段カセット (3) を引き出す。

ペーパーフィーダーを取り付ける際は、必ず MFP (1) 各 1 個を外して保管場所 (2) に取り付 4.ピン (4)1 本を外し、MFP 本体の下段カセッ
本体の主電源スイッチを OFF にし、
MFP 本体の電ける。ト (3) を取り外す。
源プラグを抜いてから作業をおこなうこと。 2.各カセットを静かに押し込む。
2
4
B
6 10 9
6
5 8
7
3
A 5
7
A
5.Place the MFP (7) on the paper feeder (A) 6.Secure the MFP (7) to the paper feeder (A) 7.Pull out the lower paper cassette rail (8) in
so that the pins (5) at the front left and front with the 2 pins (B). the MFP.
right of the paper feeder (A) are aligned with 8.Fit the hook (9) on the rail (8) into the hole
the holes (6) in the base of the MFP. (10) in the lower paper cassette (3) and
replace the lower paper cassette (3).
9.Secure the lower paper cassette (3) using
the pin (4) removed in step 4.
5.Monter le MFP (7) sur le bureau papier (A) 6.Fixer le MFP (7) au bureau papier (A) avec 7.Extraire la glissière du tiroir à papier inférieur
de sorte que les ergots (5) à l'avant gauche les 2 broches filetées (B). (8) dans le MFP.
et à l'avant droit du bureau papier (A) soient 8.Insérer le crochet (9) de la glissière (8) dans
alignés avec les trous (6) dans la base du le trou (10) du tiroir à papier inférieur (3) et
MFP. reposer le tiroir à papier inférieur (3).
9.Fixer le tiroir à papier inférieur (3) à l'aide de
la broche (4) déposée à l'étape 4.
5.Coloque el MFP (7) sobre el alimentador de 6.Asegure el MFP (7) al alimentador de papel 7. Extraiga el carril del cajón de papel inferior (8)
papel (A) de forma tal que los pasadores (5) (A) con los 2 pasadores (B). del MFP.
en los lados frontales izquierdo y derecho 8. Encaje el gancho (9) del carril (8) en el orificio
del alimentador de papel (A) estén alineados (10) del cajón de papel inferior (3) y vuelva a
con los orificios (6) de la base del MFP. colocar el cajón de papel inferior (3).
9. Asegure el cajón de papel inferior (3) usando el
clavija (4) quitado en el paso 4.
5.Den MFP (7) so auf den Papiereinzug (A) 6.Den MFP (7) mit den 2 Stiften (B) am 7. Die Schiene (8) der unteren Papierlade im
setzen, dass die Stifte (5) vorne links und Papiereinzug (A) sichern. MFP herausziehen.
vorne rechts am Papiereinzug (A) auf die 8. Den Haken (9) auf der Schiene (8) in die Öff-
Öffnungen (6) im Boden des MFP ausgeri- nung (10) der unteren Papierlade (3) einpassen
chtet sind. und die untere Papierlade (3) wieder einsetzen.
9. Die untere Papierlade (3) mit der in Schritt 4
entfernten Stift (4) befestigen.
5.Posizionare l'MFP (7) sull'unità di alimentazi- 6.Fissare l'MFP (7) all'unità di alimentazione 7.Estrarre la rotaia (8) del cassetto inferiore
one della carta (A), in modo che i perni (5) della carta (A) con i 2 perni (B). della carta nell'MFP.
alla parte frontale destra e sinistra dell'unità 8.Inserire il gancio (9) sulla rotaia (8) nel foro
di alimentazione della carta (A) siano (10) nel cassetto inferiore della carta (3) e
allineati con i fori (6) nella base dell'MFP. ricollocare il cassetto inferiore della carta (3).
9.Fissare il cassetto inferiore della carta (3)
utilizzando la perno (4) rimossa nel passo 4.
5.供纸盒 (A) 的左右前面的各插销 (5) 分别对 6.用 2 个固定插销 (B) 将 MFP 主机 (7) 固定在 7.拉出 MFP 主机的下部供纸盒 (8) 导轨。
准 MFP 主机底面的孔 (6) 后，将 MFP 主机 (7) 供纸盒 (A) 上。 8.将导轨 (8) 的卡扣 (9) 嵌入下部供纸盒 (3)
放在供纸盒 (A) 上的孔 (10) 中，按原样安装下部供纸盒 (3)
9.使用步骤 4 中取下的 1 颗固定插销 (4) 来固
定下部供纸盒 (3)
5.급지대 (A) 의 좌우 전방의 각 핀 (5) 과 MFP 6.핀 (B) 2 개로 MFP 본체 (7) 를 급지대 (A) 에 7.MFP 본체의 하단 카세트 레일 (8) 을 꺼냅니다 .
본체의 베이스 구멍 (6) 이 맞도록 급지대 (A) 고정합니다 . 8.레일 (8) 후크 (9) 를 하단 카세트 (3) 구멍
에 MFP 본체 (7) 를 놓습니다 . (10) 에 꽂습니다 . 하단 카세트 (3) 를 원래
대로 장착합니다 .
9.순서 4 에서 제거한 핀 (4) 1 개로 하단 카세
트 (3) 를 고정합니다 .
5.ペーパーフィーダー(A) の左右前方の各ピ 6.ピン (B)2 本で MFP 本体 (7) をペーパー 7.MFP 本体の下段カセットレール (8) を引き
ン (5) と MFP 本体のベースの穴 (6) が合うフィーダー(A) に固定する。出す。
ように、ペーパーフィーダー(A) に MFP 本体 8.レール (8) のフック (9) を下段カセット
(7) を載せる。 (3) の穴 (10) にはめ込み、下段カセット (3)
を元通り取り付ける。
9.手順 4 で外したピン (4)1 本で下段カセット
(3) を固定する。
3
15
13
16
11
14 H
C
12
10.Remove the screw (11) in the rear of the 11.Remove the screw (13) to remove the metal 12.Fit the hook (15) on the mounting plate (C)
paper feeder and remove the cover (12). plate (14). into the opening (16) and then align the 2
positioning projections.
13.Secure the mounting plate (C) with the
screw (H).
10.Déposer la vis (11) à l'arrière du bureau 11.Déposer la vis (13) pour enlever la plaque 12.Insérer le crochet (15) du plateau de mon-
papier et déposer le couvercle (12). métallique (14). tage (C) dans l'ouverture (16) et aligner les 2
saillies de positionnement.
13.Fixer le plateau de montage (C) avec la vis
(H).
10.Quite el tornillo (11) del lado trasero del ali- 11.Quite el tornillo (13) para desmontar la placa 12.Coloque el gancho (15) de la placa de mon-
mentador de papel y quite la cubierta (12). de metal (14). taje (C) en la abertura (16) y, después,
alinee los 2 resaltos de posición.
13.Asegure la placa de montaje (C) con el tor-
nillo (H).
10.Die Schraube (11) an der Rückseite des 11.Die Schraube (13) herausdrehen, um die 12.Den Haken (15) auf der Montageplatte (C) in
Papiereinzugs entfernen und die Abdeckung Metallplatte (14) abzunehmen. die Öffnung (16) einpassen und dann die 2
(12) abnehmen. Positionierungsnasen ausrichten.
13.Die Montageplatte (C) mit der Schraube (H)
befestigen.
10.Rimuovere la vite (11) nel retro dell'unità di 11.Rimuovere la vite (13), per rimuovere la 12.Inserire il gancio (15) sulla piastra di mon-
alimentazione della carta e quindi rimuovere piastra di metallo (14). taggio (C) nell'apertura (16) e quindi
il coperchio (12). allineare le 2 sporgenze di posizionamento.
13.Fissare la piastra di montaggio (C) con la
vite (H).
10.拆除供纸盒后部的 1 颗螺丝 (11)，拆下盖板 11.拆除 1 颗螺丝 (13)，拆下金属件 (14)。 12.将安装板 (C) 的卡扣 (15) 挂在开口部 (16)
(12)。上，并与定位用的 2 处突出部对齐。
13.使用 1 颗螺丝 (H) 来固定安装板 (C)。
10.급지대 후면의 뒤쪽 나사 (11) 1 개를 제거하 11.나사 (13) 1 개를 제거하고 쇠 (14) 를 제거합 12.부착판 (C) 의 후크 (15) 를 개구부 (16) 에 걸
고 커버 (12) 를 떼어 냅니다 . 니다 . 고 위치고정 돌기 2 곳을 맞춥니다 .
13.나사 (H) 1 개로 부착판 (C) 을 고정합니다 .
10.ペーパーフィーダー後側のビス (11)1 本を 11.ビス (13)1 本を外し、金具 (14) を取り外す。 12.取付板 (C) のフック (15) を開口部 (16) に
外し、
カバー(12) を取り外す。引っ掛けてから、位置決めの突起 2 箇所を合
わせる。
13.ビス (H)1 本で取付板 (C) を固定する。
4
24
27
23 22 26
18 20
21
17 25
19
14.Pass the power cord (17) through the edging 15.Connect the power cord (21) and the signal 17.Open the lower right cover (25) on the MFP.
(small) (18) and the signal cable (19) cable (22) to connectors (23) (24) respec- Remove the strap (26) from the shaft (27)
through the edging (large) (20) and then tively on the MFP. and remove lower right cover (25).
close the edging 16.Replace the cover (12) using the screw (11)
removed in step 10.
14.Faire passer le cordon d'alimentation (17) 15.Raccorder respectivement le cordon d'ali- 17.Ouvrir le couvercle inférieur droit (25) du
dans le (petit) passage (18) et le câble du mentation (21) et le câble à signal (22) aux MFP.
signal (19) dans le (grand) passage (20) puis connecteurs (23) (24) du MFP. Déposer la courroie (26) de l'arbre (27) et
fermer le passage. 16.Reposer le couvercle (12) à l'aide de la vis déposer le couvercle inférieur droit (25).
(11) déposée à l'étape 10.
14.Pase el cable de alimentación (17) a través 15.Conecte el cable de alimentación (21) y el 17.Abra la cubierta frontal inferior (25) del MFP.
de la pestaña (pequeña) (18) y el cable de cable de señales (22) a los conectores (23) Quite la correa (26) del eje (27) y quite la
señales (19) a través de la pestaña (grande) (24) del MFP, respectivamente. cubierta frontal inferior (25).
(20) y, después, cierre la pestaña. 16.Vuelva a colocar la cubierta (12) usando el
tornillo (11) quitado en el paso 10.
14.Das Netzkabel (17) durch den Kantenschutz 15.Das Netzkabel (21) und das Signalkabel 17.Die untere rechte Abdeckung (25) am MFP
(klein) (18) und das Signalkabel (19) durch (22) an den entsprechenden Steckverbind- öffnen.
den Kantenschutz (groß) (20) führen und ern (23) (24) des MFP anschließen. Den Riemen (26) von der Welle (27)
dann den Kantenschutz schließen. 16.Die Abdeckung (12) mittels der in Schritt 10 abnehmen und dann die untere rechte
entfernten Schraube (11) wieder anbringen. Abdeckung (25) abnehmen.
14.Passare il cavo di alimentazione (17) attra- 15.Collegare il cavo di alimentazione (21) e il 17.Aprire il pannello destro inferiore (25)
verso il bordo (piccolo) (18) e il cavo del seg- cavo del segnale (22) rispettivamente ai sull'MFP.
nale (19) attraverso il bordo (grande) (20), e connettori (23) e (24) sull'MFP. Rimuovere la cinghietta (26) dall'asta (27) e
quindi chiudere il bordo. 16.Ricollocare il coperchio (12) utilizzando la quindi rimuovere il pannello destro inferiore
vite (11) rimossa nel passo 10. (25).
14.将 AC 电线 (17) 从包边孔（小）(18)，信号线 15.将 AC 电线 (21) 以及信号线 (22) 分别与主机 17.打开 MFP 主机的右下部盖板 (25)。
(19) 从包边孔（大）(20) 中分别穿过，关闭的接插件 (23)、(24) 连接。将带子 (26) 从轴 (27) 上拆除，拆下右下部
包边孔。 16.使用在步骤 10 中拆除的 1 颗螺丝 (11) 按原盖板 (25)。
样安装盖板 (12)。
14.AC 전선 (17) 을 에징（소）(18) 에 , 신호선 15.AC 전선 (21) 및 신호선 (22) 을 본체 커넥터 17.MFP 본체의 오른쪽 아래 커버 (25) 를 엽니
(19) 을 에징（대）(20) 에 각각 지나가게 하 (23), (24) 에 각각 접속합니다 . 다.
고 에징을 닫습니다 . 16.순서 10 에서 제거한 나사 (11) 1 개로 커버 스트라프 (26) 를 축 (27) 에서 떼어내 오른쪽
(12) 를 원래대로 부착합니다 . 아래 커버 (25) 를 제거합니다 .
14.AC 電線 (17) をエッジング（小） (18) に、信号 15.AC 電線 (21) および信号線 (22) を本体のコ 17.MFP 本体の右下カバー(25) を開く。
線 (19) をエッジング（大） (20) にそれぞれネクター(23)、(24) にそれぞれ接続する。ストラップ (26) を軸 (27) から外し、右下カ
通し、エッジングを閉じる。 16.手順 10 で取り外したビス (11)1 本でカバーバー(25) を取り外す。
(12) を元通りに取り付ける。
5
29 D 29
28
30 H 30 H
18.Open the paper feeder right cover (28). 19.Fit the 3 hooks (29) on the intermediate paper conveying unit (D) into the 3 holes (30) in the
guide.
20.Secure the intermediate paper conveying unit (D) with the 2 screws (H).
18.Ouvrir le couvercle droit du bureau papier 19.Insérer les 3 crochets (29) de l'unité de transport du papier intermédiaire (D) dans les 3 trous (30)
(28). du guide.
20.Fixer l'unité de transport du papier intermédiaire (D) à l'aide des 2 vis (H).
18.Abra la cubierta derecha del alimentador de 19.Coloque los 3 ganchos (29) de la unidad de transporte de papel intermedia (D) en los 3 orificios
papel (28). (30) de la guía.
20.Asegure la unidad de transporte de papel intermedia (D) con los 2 tornillos (H).
18.Die rechte Abdeckung (28) des Papiere- 19.Die 3 Haken (29) an der eingesetzten Papierfördereinheit (D) in die 3 Öffnungen (30) in der Füh-
inzugs öffnen. rung einpassen.
20.Die eingesetzte Papierfördereinheit (D) mit den 2 Schrauben (H) sichern.
18.Aprire il pannello destro (28) dell'unità di ali- 19.Inserire i 3 ganci (29) sull'unità intermediale di trasporto carta (D) nei 3 fori (30) nella guida.
mentazione della carta. 20.Fissare l'unità intermediale di trasporto carta (D) con le 2 viti (H).
18.打开供纸盒的右部盖板 (28)。 19.将中间搬运单元 (D) 的 3 个卡扣 (29) 嵌入导向板的 3 个孔 (30) 中。

20.使用 2 颗螺丝 (H) 来固定中间搬运单元 (D)。
18.급지대 오른쪽 커버 (28) 를 엽니다 . 19.중간반송유니트 (D) 의 후크 (29) 3 개를 가이드 구멍 (30) 3 곳에 꽂습니다 .
20.나사 (H) 2 개로 중간반송유니트 (D) 를 고정합니다 .
18.ペーパーフィーダーの右カバー(28) を開 19.中間搬送ユニット (D) のフック (29)3 個をガイドの穴 (30)3 カ所にはめ込む。

く。 20.ビス (H)2 本で中間搬送ユニット (D) を固定する。
6
31
F
32
33 34
21.Connect the intermediate paper conveying 23.Insert the projection (32) on the wire cover 25.Turn the adjusters on each corner (34) until
unit connector (31). (F) into the hole (33) in the paper feeder and they reach the floor and then secure the
22.Attach the clamp (E) and secure the connec- install the wire cover (F). paper feeder.
tor wire. 24.Close the paper feeder right cover (28) and
replace the lower right cover (25) on the
MFP.
21.Raccorder le connecteur (31) de l'unité de 23.Insérer la saillie (32) du couvercle du câble 25.Faire tourner les dispositifs de réglage de
transport du papier intermédiaire. (F) dans le trou (33) du bureau papier et chacun des coins (34) jusqu'à ce qu'ils
22.Monter le collier (E) et fixer le câble du con- reposer le couvercle du câble (F). touchent le sol et fixer ensuite le bureau
necteur. 24.Fermer le couvercle droit du bureau papier papier.
(28) et reposer le couvercle inférieur droit
(25) sur le MFP.
21.Conecte el conector de la unidad de trans- 23.Inserte el resalto (32) de la cubierta para el 25.Gire los reguladores en cada esquina (34)
porte de papel intermedia (31). cable (F) en el orificio (33) del alimentador hasta que lleguen al piso y, a continuación,
22.Fije el sujetador (E) y asegure el cable del de papel e instale la cubierta para el cable asegure el alimentador de papel.
conector. (F).
24.Cierre la cubierta derecha del alimentador
de papel (28) y vuelva a colocar la cubierta
derecha inferior (25) en el MFP.
21.Den Steckverbinder (31) der eingesetzten 23.Die Nase (32) der Kabelabdeckung (F) in die 25.Die Einsteller an jeder Ecke (34) drehen, bis
Papierfördereinheit anschließen. Öffnung (33) des Papiereinzugs einsetzen sie den Boden berühren, und dann den
22.Die Klemme (E) anbringen und das Kabel und die Kabelabdeckung (F) anbringen. Papiereinzug sichern.
des Steckverbinders sichern. 24.Die rechte Abdeckung (28) des Papiere-
inzugs schließen und die untere rechte
Abdeckung (25) wieder am MFP einsetzen.
21.Collegare il connettore (31) dell'unità inter- 23.Inserire la sporgenza (32) del coperchio cavi 25.Ruotare i regolatori (34) presenti su ciascun
mediale di trasporto carta. (F) nel foro (33) nell'unità di alimentazione angolo finché vengano a contatto con il pavi-
22.Applicare il morsetto (E) e fissare il cavo del della carta ed installare il coperchio cavi (F). mento, e quindi fissare l’unità di alimentazi-
connettore. 24.Chiudere il pannello destro (28) dell'unità di one della carta.
alimentazione della carta e ricollocare il pan-
nello destro inferiore (25) sull'MFP.
21.连接中间搬运单元的接插件 (31)。 23.将电线盖板 (F) 的突出部 (32) 插入供纸盒的 25.转动四角上的调节器 (34) 直至与地面接触，
22.安装夹钳 (E)，以固定接插件电线。孔 (33) 中，安装电线盖板 (F)。然后再固定供纸盒
24.关闭供纸盒的右部盖板 (28)，按原样安装
MFP 主机的右下部盖板 (25)。
21.중간반송유니트의 커넥터 (31) 를 접속합니 23.전선커버 (F) 의 돌기 (32) 를 급지대의 구멍 25.네 곳의 어져스터 (34) 를 맨 밑에 닿을 위치
다. (33) 에 넣고 전선커버 (F) 를 부착합니다 . 까지 돌려 급지대를 고정합니다 .
22.클램프 (E) 를 부착 , 커넥터 전선을 고정합니 24.급지대 오른쪽 커버 (28) 를 닫고 , MFP 본체
다. 의 오른쪽 아래 커버 (25) 를 원래대로 부착
합니다 .
21.中間搬送ユニットのコネクター(31) を接続 23.電線カバー(F) の突起 (32) をペーパー 25.四隅のアジャスター(34) を床に接触する位

する。フィーダーの穴 (33) に入れて、電線カバー置まで回し、
ペーパーフィーダーを固定す
22.クランプ (E) を取り付け、
コネクター電線を (F) を取り付ける。る。
固定する。 24.ペーパーフィーダーの右カバー(28) を閉
じ、MFP 本体の右下カバー(25) を元通りに取
り付ける。
7
Setting the paper size plate and media type Skewed paper feed adjustment
plate 1.Connect the MFP power plug to the wall outlet and turn the MFP main power switch on.
Fold the plates in half and insert them into the 2.Load paper into the cassette and make a test copy to check the image.
size and media type slots respectively. For more 3.If the image is skewed (skewed paper feed), make the adjustments described below.
details, refer to the operation guide. <Reference value> Left-right difference of 1.5 mm or less
Réglage du plateau de format du papier et du Réglage de l'entraînement du papier en biais

plateau du type de média 1.Insérer la fiche d’alimentation du MFP dans la prise murale et mettre l’interrupteur principal du
Rabattre à moitié les plateaux et les insérer MFP sous tension.
respectivement dans les fentes du format et du 2.Mettre du papier dans le tiroir et effectuer une copie d'essai pour vérifier l'image.
type de média. Pour plus de détail, voir le mode 3.Si l'image est en biais (entraînement du papier en biais), régler en procédant comme décrit ci-
d'emploi. dessous.
<Valeur de référence> Différence de droite à gauche de 1,5 mm ou moins.
Ajuste de la placa de tamaño de papel y la Ajuste de alimentación de papel torcida

placa de tipo de medio 1.Conecte el enchufe del MFP en el receptáculo de pared y encienda el interruptor principal del
Pliegue las placas por la mitad e insértelas en MFP.
las ranuras de tamaño y tipo de medio respec- 2.Introduzca papel en el cajón y haga una copia de prueba para verificar la imagen.
tivamente. Para obtener más información, con- 3. Si la imagen está torcida (alimentación del papel torcida) haga los ajustes que se describen a
sulte la Guía de uso. continuación.
<Valor de referencia> diferencia izquierda-derecha de 1,5 mm o menor.
Einsetzen der Papierformatplatte und der Einstellung bei verkantetem Papiereinzug

Medientypplatte 1.Stecken Sie den Netzstecker des MFP in die Wandsteckdose und schalten Sie den MFP am
Die Platten halb zusammenklappen und in die Hauptschalter ein.
Öffnungen für Format bzw. Medientyp ein- 2.Legen Sie Papier in die Papierlade ein und machen Sie eine Testkopie, um das Bild zu prüfen.
schieben. Näheres hierzu siehe Bedienungs- 3.Nehmen Sie nachstehende Einstellungen vor, falls das Bild verkantet ist (verkanteter Papiere-
anleitung. inzug).
<Bezugswert> Links-rechts-Differenz maximal 1,5 mm.
Impostazione della piastra di formato carta e Regolazione alimentazione obliqua carta

della piastra del tipo di supporto 1.Collegare la spina del cavo di alimentazione dell’MFP alla presa a muro della rete elettrica e
Piegare le piastre a metà e inserirle rispettiva- accendere l’interruttore principale di alimentazione.
mente negli slot per il formato e il tipo di sup- 2.Caricare carta nel cassetto ed eseguire una copia di prova per controllare l'immagine.
porto. Per maggiori dettagli, fare riferimento alla 3.Se l'immagine risulta obliqua (alimentazione obliqua della carta), eseguire le regolazioni descritte
guida alle funzioni. sotto.
<Valore di riferimento> Differenza tra destra e sinistra di 1,5 mm o inferiore
纸张尺寸托板和纸张种类托板的安装歪斜进纸调节
把托板对折后，分别插入纸张尺寸、种类标记插 1.将 MFP 主机上的电源插头插入电源插座中，打开主电源开关。
槽中。详情请参阅使用说明书。 2.在纸盒中放入纸张。进行测试复印以确认图像。
3.图像倾斜（歪斜进纸）时进行以下调节。
＜基准值＞左右差 1.5mm 以下
용지크기 플레이트와 용지종류 플레이트의 세트 경사급지 조정

플레이트를 2 곳 접어 크기 , 용지종류표시 슬롯 1.MFP 본체 전원플러그를 콘센트에 꽂고 주 전원 스위치를 ON 으로 합니다 .
에 각각 삽입합니다 . 상세는 사용설명서를 참조 . 2.카세트에 용지를 장착합니다 . 시험복사를 하고 화상을 확인합니다 .
3.화상이 기울어져 있는 （경사급지）경우에는 다음 조정을 합니다 .
＜기준치＞ 좌우차 1.5mm 이하
用紙サイズプレートと用紙種類プレートのセット斜め給紙調整
プレートを 2 つ折りにし、サイズ、
用紙種表示ス 1.MFP 本体の電源プラグをコンセントに差し込み、主電源スイッチを ON にする。
ロットにそれぞれ挿入する。詳細は使用説明書 2.カセットに用紙をセットする。テストコピーをおこない、画像を確認する。
を参照。 3.画像が傾いている（斜め給紙）場合は次の調整をおこなう。
＜基準値＞左右差 1.5mm 以下
8
36
35 37
4.Pull out the cassette (35) in the paper feeder and loosen the 4 screws (36).
5.Turn the adjusting screw (37) to adjust the cursor skew.
6.Retighten the 4 screws (36).
7.Make another test copy to check the image.
4.Sortir le tiroir (35) du bureau papier et desserrer les 4 vis (36).

5.Faire tourner la vis de réglage (37) pour régler la déviation du curseur.
6.Resserrer les 4 vis (36).
7.Faire une autre copie d'essai pour vérifier l'image.
4.Extraiga el cajón (35) del alimentador de papel y afloje los 4 tornillos (36).
5.Gire el tornillo de ajuste (37) para ajustar la desviación del cursor.
6.Vuelva a apretar los 4 tornillos (36).
7.Haga otra copia de prueba para verificar la imagen.
4.Ziehen Sie die Papierlade (35) aus dem Papiereinzug und lösen Sie die 4 Schrauben (36).
5.Drehen Sie die Einstellschraube (37), um die Cursor-Verkantung zu korrigieren.
6.Ziehen Sie die 4 Schrauben (36) wieder an
7.Erstellen Sie zur Überprüfung des Bilds noch einmal eine Testkopie.
4.Estrarre il cassetto (35) dell'unità di alimentazione della carta e quindi allentare le 4 viti (36).
5.Ruotare la vite di regolazione (37) per regolare l'inclinazione del cursore.
6.Ristringere le 4 viti (36).
7.Eseguire un'altra copia di prova per controllare l'immagine.
4.拉出供纸盒 (35) ，拧松 4 颗螺丝 (36)。

5.旋转调节螺丝 (37) ，以调节游标的倾斜。
6.拧紧 4 颗螺丝 (36)。
7.再次进行测试复印，确认图像。
4.급지 카세트 (35) 를 빼 내어 나사 (36) 4 개를 느슨하게 합니다 .

5.조정나사 (37) 을 돌려 커서 경사조정을 합니다 .
6.나사 (36) 4 개를 조입니다 .
7.다시 시험복사를 하고 화상을 확인합니다 .
4.ペーパーフィーダーのカセット (35) を引き出し、ビス (36)4 本を緩める。

5.調整ネジ (37) を回し、カーソルの傾き調整をおこなう。
6.ビス (36)4 本を締め付ける。
7.再度、テストコピーをおこない、画像を確認する。
9
㧙
b
㧗
a c d
Adjusting the leading edge timing

The reference value for the leading edge timing is 20 ±1.5 mm at position (b) in the correct image (a). If the timing is outside this range, perform the fol-
lowing adjustment.
1.Set maintenance mode U034, select LSU Out Left and Cassette(L)
2.Adjust the values.
Test pattern (c): Increase the setting value. Test pattern (d): Decrease the setting value.
3.Press the Start key to confirm the setting value.
Réglage de la synchronisation du bord de tête

La valeur de référence de la synchronisation du bord de tête est de 20 ±1,5 mm à la position (b) d'une image correcte (a). Si la synchronisation est hors
de cette plage, procéder au réglage suivant.
1.Passer en mode maintenance U034, sélectionner LSU Out Left et Cassette(L).
2.Régler les valeurs.
Mire d' essai (c): Augmentez la valeur de réglage. Mire d' essai (d): Diminuez la valeur de réglage.
3.Appuyer sur la touche de Start pour confirmer la valeur de réglage.
Cómo ajustar la sincronización del borde superior

El valor de referencia de la sincronización del borde superior es de 20 ±1,5 mm en la posición (b) de la imagen correcta (a). Si la sincronización estuviera
fuera de este rango, haga el siguiente ajuste.
1.Entre al modo de mantenimiento U034, seleccione LSU Out Left y Cassette(L).
2.Ajuste los valores.
Patrón de prueba (c): Aumente el valor de configuración. Patrón de prueba (d): Reduzca el valor de configuración.
3.Pulse la tecla de Start para confirmar el valor de configuración.
Einstellen des Vorderkanten-Timing

Der Bezugswert des Vorderkanten-Timing ist 20 ±1,5 mm an Position (b) des korrekten Bilds (a). Falls das Timing außerhalb dieses Bereichs liegt, ist fol-
gende Einstellung vorzunehmen.
1.Schalten Sie in den Wartungsmodus U034, wählen Sie LSU Out Left und Cassette(L).
2.Die Werte einstellen.
Testmuster (c): Den Einstellwert erhöhen. Testmuster (d): Den Einstellwert verringern.
3.Den Einstellwert durch Drücken der Start-Taste bestätigen.
Regolazione della sincronizzazione del bordo principale

Il valore di riferimento per la sincronizzazione del bordo principale è 20 ±1,5 mm alla posizione (b) nell'immagine corretta (a). Se la sincronizzazione è
all'infuori di questa gamma, effettuare la regolazione seguente.
1.Impostare la modalità manutenzione U034, selezionare LSU Out Left e Cassette(L).
2. Regolare i valori.
Modello di prova (c): Aumentare il valore dell'impostazione. Modello di prova (d): Diminuire il valore dell'impostazione.
3.Premere il tasto di Start per confermare il valore dell'impostazione.
前端对位调节
前端对位的基准值在矫正图像 (a) 的 (b) 位置为 20±1.5mm。超出该范围时，须进行以下调节。
1.设置维护模式 U034，选择 LSU Out Left、Cassette(L)。
2.调整设定值。
测试图案 (c) ：调高设定值。测试图案 (d) ：调低设定值。
3.按 Start 键，以确定设定值。
선단 타이밍 조정
선단 타이밍은 적정화상 (a) 의 (b) 위치에서 기준치는 20±1.5mm. 여기에서 벗어나는 것은 이하의 조정을 합니다 .
1.메인터넌스 모드 U034 를 세트하고 LSU Out Left, Cassette(L) 을 선택합니다 .
2.설정치를 조정합니다 .
테트스 패턴 (c) ：설정치를 높입니다 . 테스트 패턴 (d) ：설정치를 내립니다 .
3.시작키를 누르고 설정치를 확인합니다 .
先端タイミング調整
先端タイミングは、適正画像 (a) の (b) の位置で基準値は 20±1.5mm。これから外れるときは以下の調整をおこなう。
1.メンテナンスモード U034 をセットし、LSU Out Left、Cassette(L) を選択する。
2.設定値を調整する。
テストパターン (c) ：設定値を上げる。　テストパターン (d) ：設定値を下げる。
3.スタートキーを押し、設定値を確定する。
10
f
㧙㧗
e g h
Adjusting the center line

The reference value for the center line is ±0.5 mm or less at position (f) in the correct image (e). If the center line position is outside this range, perform the
following adjustment.
1.Set maintenance mode U034, select LSU Out Left and Cassette3 or Cassette4.
Test pattern (g): Increase the setting value. Test pattern (h): Decrease the setting value.
Réglage de l'axe
La valeur de référence pour l'axe est de ±0,5 mm ou moins à la position (f) d'une image correcte (e). Si la position de l'axe est hors de cette plage,
effectuez le réglage suivant.
1.Passer en mode maintenance U034, sélectionner LSU Out Left et Cassette3 ou Cassette4.
Mire d' essai (g): Augmentez la valeur de réglage. Mire d' essai (h): Diminuez la valeur de réglage.
Ajuste de la línea central
El valor de referencia de la línea central es de ±0,5 mm o menor, en la posición (f) de la imagen correcta (e). Si la posición de la línea central estuviera
1.Entre al modo de mantenimiento U034, seleccione LSU Out Left y Cassette3 o Cassette4.
Patrón de prueba (g): Aumente el valor de configuración. Patrón de prueba (h): Reduzca el valor de configuración.
Einstellen der Mittenlinie

Der Bezugswert für die Mittenlinie ist ±0,5 mm oder weniger an Position (f) des korrekten Bilds (e). Falls die Mittenlinie außerhalb dieses Bereichs liegt,
ist folgende Einstellung vorzunehmen.
1.Schalten Sie in den Wartungsmodus U034, wählen Sie LSU Out Left und Cassette3 oder Cassette4.
Testmuster (g): Den Einstellwert erhöhen. Testmuster (h): Den Einstellwert verringern.
Regolazione della linea centrale

Il valore di riferimento per la linea centrale è ±0,5 mm o inferiore alla posizione (f) nell'immagine corretta (e). Se la posizione della linea centrale è all'infu-
ori di questa gamma, effettuare la regolazione seguente.
1.Impostare la modalità manutenzione U034, selezionare LSU Out Left e Cassette3 o Cassette4.
2.Regolare i valori.
Modello di prova (g): Aumentare il valore dell'impostazione. Modello di prova (h): Diminuire il valore dell'impostazione.
中心线调节
中心线的基准值在矫正图像 (e) 的 (f) 位置为 ±0.5mm 以内。超出该范围时，须进行以下调节。
1.设置维护模式 U034，选择 LSU Out Left、Cassette3 或 Cassette4。
测试图案 (g) ：调高设定值。测试图案 (h) ：调低设定值。
센터라인 조정
센터라인은 적정화상 (e) 의 (f) 위치에서 기준치는 ±0.5mm 이내 . 여기에서 벗어나는 것은 이하의 조정을 합니다 .
1.메인터넌스 모드 U034 를 세트하고 LSU Out Left, Cassette3 또는 Cassette4 를 선택합니다 .
테트스 패턴 (g) ：설정치를 높입니다 . 테스트 패턴 (h) ：설정치를 내립니다 .
センターライン調整
センターラインは、適正画像 (e) の (f) の位置で基準値は ±0.5mm 以内。これから外れるときは以下の調整をおこなう。
1.メンテナンスモード U034 をセットし、LSU Out Left、Cassette3 または Cassette4 を選択する。
テストパターン (g) ：設定値を上げる。　テストパターン (h) ：設定値を下げる。
11
LARGE CAPACITY FEEDER
E
B
C
F G
A D I
E. Clamp ........................................................ 1 Be sure to remove any tape and/or cushioning

English
F. Wire cover.................................................. 1 material from supplied parts.
Supplied parts G. Paper size plate ......................................... 2
A. Paper feeder.............................................. 1 H. S Tite screw M4 × 8 ................................... 3
B. Pin ............................................................. 2 I. Paper type plate......................................... 2
C. Retainer ..................................................... 1
D. Intermediate paper conveying unit............. 1
E. Collier......................................................... 1 Veillez à retirer les morceaux de bande adhé-

Français
F. Couvercle de câble .................................... 1 sive et/ou les matériaux de rembourrage des
Pièces fournies G. Plateau de format du papier ...................... 2 pièces fournies.
A. Bureau papier ............................................ 1 H. Vis S Tite M4 × 8 ....................................... 3
B. Broche ....................................................... 2 I. Plaque de type de papier........................... 2
C. Élément de retenue ................................... 1
D. Unité de transport du papier intermédiaire 1
E. Sujetador ................................................... 1 Asegúrese de despegar todas las cintas y/o

Español
F. Cubierta para el cable................................ 1 material amortiguador de las partes suministra-
Partes suministradas G. Placa de tamaño de papel ......................... 2 das.
A. Alimentador de papel................................. 1 H. Tornillo S Tite M4 × 8 ................................. 3
B. Clavija........................................................ 2 I. Placa de tipo de papel ............................... 2
C. Retén ......................................................... 1
D. Unidad de transporte de papel intermedia. 1
E. Klemme...................................................... 1 Entfernen Sie Klebeband und/oder Dämpfungs-

Deutsch
F. Kabelabdeckung ........................................ 1 material vollständig von den mitgelieferten
Gelieferte Teile G. Papierformatplatte ..................................... 2 Teilen.
A. Papiereinzug.............................................. 1 H. S-Tite-Schraube M4 × 8............................. 3
B. Stift............................................................. 2 I. Papiertypplatte........................................... 2
C. Halterung ................................................... 1
D. Eingesetzte Papierfördereinheit ................ 1
E. Morsetto..................................................... 1 Accertarsi di rimuovere tutti i nastri adesivi e/o il

Italiano
F. Coperchio cavi ........................................... 1 materiale di imbottitura dalle parti fornite.
Parti di fornitura G. Piastra formato carta ................................. 2
A. Unità di alimentazione della carta ............. 1 H. Vite S Tite M4 × 8 ...................................... 3
B. Perno ........................................................ 2 I. Piastra tipo carta........................................ 2
C. Fermo ....................................................... 1
D. Unità intermediale di trasporto carta.......... 1
简体中文 E. 夹钳 .................................1 如果附属品上带有固定胶带，缓冲材料时务必揭

F. 电线盖板 .............................1 下。
附属品 G. 纸张尺寸托板 .........................2
A. 供纸工作台........................... 1 H. 紧固型 S 螺丝 M4×8 ....................3
B. 固定插销............................. 2 I. 纸张种类托板 .........................2
C. 安装板............................... 1
D. 中间搬运单元......................... 1
한국어 E. 크램프............................................... 1 동봉품에 고정 테이프 , 완충재가 붙어 있는 경

F. 전선커버............................................ 1 우에는 반드시 제거할 것 .
동봉품 G. 용지크기 플레이트............................... 2
A. 급지대............................................... 1 H. 나사 M4×8S 타이트............................. 3
B. 핀..................................................... 2 I. 용지종류 플레이트............................... 2
C. 부착판............................................... 1
D. 중간반송유니트................................... 1
日本語 E. クランプ .............................1 同梱品に固定テープ、緩衝材が付いている場合

F. 電線カバー ...........................1 は必ず取り外すこと。
同梱品 G. 用紙サイズプレート ...................2
A. ペーパーフィーダー................... 1 H. ビス M4×8S タイト ....................3
B. ピン................................. 2 I. 用紙種類プレート .....................2
C. 取付板............................... 1
D. 中間搬送ユニット..................... 1
1
3
Procedure 1.Pull out the right cassette (1) and left cas- 3.Remove the lower paper cassette (4) from
Be sure to turn the MFP main power switch off sette (2), remove each of the lift plate stop- the MFP
and disconnect the MFP power plug from the pers (3) and attach them in the storage 4.Remove the pin (5) and remove the lower
wall outlet before starting to install the paper location. paper cassette (4) in the MFP.
feeder. 2.Gently close each cassette.
Procédure 1.Sortir le tiroir droit (1) et le tiroir gauche (2), 3.Retirer le tiroir inférieur (4) du MFP.
Veiller à bien mettre l’interrupteur principal du déposer toutes les butées du plateau de 4.Déposer la broche (5) et le tiroir à papier
MFP hors tension et à débrancher la fiche d’ali- levage (3) et les ranger soigneusement. inférieur (4) du MFP.
mentation du MFP de la prise murale avant de 2.Refermer progressivement chaque tiroir.
commencer l’installation du bureau papier.
Procedimiento 1.Extraiga el cajón derecho (1) y el cajón 3.Quite el cajón de papel inferior (4) del MFP.
Asegúrese de apagar el interruptor principal del izquierdo (2), quite cada uno de los topes de 4.Quite el clavija (5) y el cajón de papel inferior
MFP y de desconectar el enchufe del MFP del placa de elevación (3) y fíjelos en el lugar de (4) del MFP.
receptáculo de pared antes de empezar a insta- almacenamiento.
lar el alimentador de papel. 2.Cierre suavemente cada bandeja.
Verfahren 1.Die rechte Papierlade (1) und die linke 3.Nehmen Sie die untere Papierlade (4) vom
Schalten Sie unbedingt den Hauptschalter des Papierlade (2) herausziehen, jeden der MFP ab.
MFP aus, und ziehen Sie den Netzstecker des Hebeplattenanschläge (3) entfernen und in 4.Die Stift (5) entfernen und die untere Papier-
MFP von der Netzsteckdose ab, bevor Sie mit der vorgesehenen Position verstauen. lade (4) im MFP abnehmen.
der Installation des Papiereinzugs beginnen. 2.Alle Kassetten sachte schließen.
Procedura 1.Estrarre il cassetto destro (1) e il cassetto 3.Rimuovere il cassetto inferiore della carta (4)
Prima di dare inizio alla procedura di installazi- sinistro (2), rimuovere ciascuno dei fermi (3) dall’MFP.
one dell’unità di alimentazione della carta, non della piastra di sollevamento ed applicarli 4.Rimuovere la perno (5) e quindi rimuovere il
mancare di spegnere l’MFP usando l’interruttore nella posizione di conservazione. cassetto inferiore della carta (4) nell'MFP.
principale di alimentazione e di disinserire la 2.Chiudere delicatamente ciascun cassetto.
spina del cavo di alimentazione dalla presa a
muro della rete elettrica.
安装步骤 1.拉出右侧供纸盒 (1) 以及左侧供纸盒 (2)，拆 3.取出 MFP 主机的下部供纸盒 (4)。

安装供纸工作台时，必须先关闭 MFP 主机上的主下各 1 个升降板挡块 (3)，并安装在保管场所 4.拆除 1 颗固定插销 (5)，取出 MFP 主机的下部
电源开关，并拔出电源插头后方可进行工作。上。供纸盒 (4)。
2.轻轻地推入各供纸盒。
설치순서 1.카세트 오른쪽 (1) 및 카세트 왼쪽 (2) 을 꺼 3.MFP 본체의 하단 카세트 (4) 를 꺼냅니다 .
급지대를 설치할 때에는 반드시 MFP 본체의 주 내어 리프트판 스토퍼 (3) 각 1 개를 제거하 4.핀 (5) 1 개를 제거하고 MFP 본체 하단 카세
전원 스위치를 OFF 로 하고 MFP 본체 전원 플 고 보관장소에 부착합니다 . 트 (4) 를 꺼냅니다 .
러그를 빼고 작업을 할 것 . 2.각 카세트를 조용히 밀어 넣습니다 .
取付手順 1.カセット右 (1) およびカセット左 (2) を引 3.MFP 本体の下段カセット (4) を引き出す。

ペーパーフィーダーを取り付ける際は、必ず MFP き出し、リフト板ストッパー(3) 各 1 個を取 4.ピン (5)1 本を外し、MFP 本体の下段カセッ
本体の主電源スイッチを OFF にし、
MFP 本体の電り外し、保管場所に取り付ける。ト (4) を取り外す。
源プラグを抜いてから作業をおこなうこと。 2.各カセットを静かに押し込む。
2
B 5
7 8
7
11 10
6
9
6
8 4
A A
5.Place the MFP (8) on the paper feeder (A) 6.Secure the MFP (8) to the paper feeder (A) 7.Pull out the lower paper cassette rail (9) in
so that the pins (6) at the front left and front with the 2 pins (B). the MFP.
right of the paper feeder (A) are aligned with 8.Fit the hook (10) on the rail (9) into the hole
the holes (7) in the base of the MFP. (11) in the lower paper cassette (4) and
replace the lower paper cassette (4).
9.Secure the lower paper cassette (4) using
the pin (5) removed in step 4.
5.Monter le MFP (8) sur le bureau papier (A) 6.Fixer le MFP (8) au bureau papier (A) avec 7.Extraire la glissière du tiroir à papier inférieur
de sorte que les ergots (6) à l'avant gauche les 2 broches filetées (B). (9) dans le MFP.
et à l'avant droit du bureau papier (A) soient 8.Insérer le crochet (10) de la glissière (9)
alignés avec les trous (7) dans la base du dans le trou (11) du tiroir à papier inférieur
MFP. (4) et reposer le tiroir à papier inférieur (4).
9.Fixer le tiroir à papier inférieur (4) à l'aide de
la broche (5) déposée à l'étape 4.
5.Coloque el MFP (8) sobre el alimentador de 6.Asegure el MFP (8) al alimentador de papel 7. Extraiga el carril del cajón de papel inferior (9)
papel (A) de forma tal que los pasadores (6) (A) con los 2 pasadores (B). del MFP.
en los lados frontales izquierdo y derecho 8. Encaje el gancho (10) del carril (9) en el orificio
del alimentador de papel (A) estén alineados (11) del cajón de papel inferior (4) y vuelva a
con los orificios (7) de la base del MFP. colocar el cajón de papel inferior (4).
9. Asegure el cajón de papel inferior (4) usando el
clavija (5) quitado en el paso 4.
5.Den MFP (8) so auf den Papiereinzug (A) 6.Den MFP (8) mit den 2 Stiften (B) am 7. Die Schiene (9) der unteren Papierlade im MFP
setzen, dass die Stifte (6) vorne links und Papiereinzug (A) sichern. herausziehen.
vorne rechts am Papiereinzug (A) auf die 8. Den Haken (10) auf der Schiene (9) in die Öff-
Öffnungen (7) im Boden des MFP ausgeri- nung (11) der unteren Papierlade (4) einpassen
chtet sind. und die untere Papierlade (4) wieder einsetzen.
9. Die untere Papierlade (4) mit der in Schritt 4
entfernten Stift (5) befestigen.
5.Posizionare l'MFP (8) sull'unità di alimentazi- 6.Fissare l'MFP (8) all'unità di alimentazione 7.Estrarre la rotaia (9) del cassetto inferiore
one della carta (A), in modo che i perni (6) della carta (A) con i 2 perni (B). della carta nell'MFP.
alla parte frontale destra e sinistra dell'unità 8.Inserire il gancio (10) sulla rotaia (9) nel foro
di alimentazione della carta (A) siano (11) nel cassetto inferiore della carta (4) e
allineati con i fori (7) nella base dell'MFP. ricollocare il cassetto inferiore della carta (4).
9.Fissare il cassetto inferiore della carta (4)
utilizzando la perno (5) rimossa nel passo 4.
5.供纸盒 (A) 的左右前面的各插销 (6) 分别对 6.用 2 个固定插销 (B) 将 MFP 主机 (8) 固定在 7.拉出 MFP 主机的下部供纸盒 (9) 导轨。
准 MFP 主机底面的孔 (7) 后，将 MFP 主机 (8) 供纸盒 (A) 上。 8.将导轨 (9) 的卡扣 (10) 嵌入下部供纸盒 (4)
放在供纸盒 (A) 上的孔 (11) 中，按原样安装下部供纸盒 (4)
9.使用步骤 4 中取下的 1 颗固定插销 (5) 来固
定下部供纸盒 (4)
5.급지대 (A) 의 좌우 전방의 각 핀 (6) 과 MFP 6.핀 (B) 2 개로 MFP 본체 (8) 를 급지대 (A) 에 7.MFP 본체의 하단 카세트 레일 (9) 을 꺼냅니다 .
본체의 베이스 구멍 (7) 이 맞도록 급지대 (A) 고정합니다 . 8.레일 (9) 후크 (10) 를 하단 카세트 (4) 구멍
에 MFP 본체 (8) 를 놓습니다 . (11) 에 꽂습니다 . 하단 카세트 (4) 를 원래
대로 장착합니다 .
9.순서 4 에서 제거한 핀 (5) 1 개로 하단 카세
트 (4) 를 고정합니다 .
5.ペーパーフィーダー(A) の左右前方の各ピ 6.ピン (B)2 本で MFP 本体 (8) をペーパー 7.MFP 本体の下段カセットレール (9) を引き
ン (6) と MFP 本体のベースの穴 (7) が合うフィーダー(A) に固定する。出す。
ように、ペーパーフィーダー(A) に MFP 本体 8.レール (9) のフック (10) を下段カセット
(8) を載せる。 (4) の穴 (11) にはめ込み、下段カセット (4)
を元通り取り付ける。
9.手順 4 で外したピン (5)1 本で下段カセット
(4) を固定する。
3
16
14
17
12
15 H
C
13
10.Remove the screw (12) in the rear of the 11.Remove the screw (14) to remove the metal 12.Fit the hook (16) on the mounting plate (C)
paper feeder and remove the cover (13). plate (15). into the opening (17) and then align the 2
positioning projections.
13.Secure the mounting plate (C) with the
screw (H).
10.Déposer la vis (12) à l'arrière du bureau 11.Déposer la vis (14) pour enlever la plaque 12.Insérer le crochet (16) du plateau de mon-
papier et déposer le couvercle (13). métallique (15). tage (C) dans l'ouverture (17) et aligner les 2
saillies de positionnement.
13.Fixer le plateau de montage (C) avec la vis
(H).
10.Quite el tornillo (12) del lado trasero del ali- 11.Quite el tornillo (14) para desmontar la placa 12.Coloque el gancho (16) de la placa de mon-
mentador de papel y quite la cubierta (13). de metal (15). taje (C) en la abertura (17) y, después,
alinee los 2 resaltos de posición.
13.Asegure la placa de montaje (C) con el tor-
nillo (H).
10.Die Schraube (12) an der Rückseite des 11.Die Schraube (14) herausdrehen, um die 12.Den Haken (16) auf der Montageplatte (C) in
Papiereinzugs entfernen und die Abdeckung Metallplatte (15) abzunehmen. die Öffnung (17) einpassen und dann die 2
(13) abnehmen. Positionierungsnasen ausrichten.
13.Die Montageplatte (C) mit der Schraube (H)
befestigen.
10.Rimuovere la vite (12) nel retro dell'unità di 11.Rimuovere la vite (14), per rimuovere la 12.Inserire il gancio (16) sulla piastra di mon-
alimentazione della carta e quindi rimuovere piastra di metallo (15). taggio (C) nell'apertura (17) e quindi
il coperchio (13). allineare le 2 sporgenze di posizionamento.
13.Fissare la piastra di montaggio (C) con la
vite (H).
10.拆除供纸盒后部的 1 颗螺丝 (12)，拆下盖板 11.拆除 1 颗螺丝 (14)，拆下金属件 (15)。 12.将安装板 (C) 的卡扣 (16) 挂在开口部 (17)
(13) 。上，并与定位用的 2 处突出部对齐。
13.使用 1 颗螺丝 (H) 来固定安装板 (C)。
10.급지대 후면의 뒤쪽 나사 (12) 1 개를 제거하 11.나사 (14) 1 개를 제거하고 쇠 (15) 를 제거합 12.부착판 (C) 의 후크 (16) 를 개구부 (17) 에 걸
고 커버 (13) 를 떼어 냅니다 . 니다 . 고 위치고정 돌기 2 곳을 맞춥니다 .
13.나사 (H) 1 개로 부착판 (C) 을 고정합니다 .
10.ペーパーフィーダー後側のビス (12)1 本を 11.ビス (14)1 本を外し、金具 (15) を取り外す。 12.取付板 (C) のフック (16) を開口部 (17) に
外し、
カバー(13) を取り外す。引っ掛けてから、位置決めの突起 2 箇所を合
わせる。
13.ビス (H)1 本で取付板 (C) を固定する。
4
25
28
24 23 27
19 21
22
18 26
20
14.Pass the power cord (18) through the edging 15.Connect the power cord (22) and the signal 17.Open the lower right cover (26) on the MFP.
(small) (19) and the signal cable (20) cable (23) to connectors (24) (25) respec- Remove the strap (27) from the shaft (28)
through the edging (large) (21) and then tively on the MFP. and remove lower right cover (26).
close the edging 16. Replace the cover (13) using the screw (12)
removed in step 10.
14.Faire passer le cordon d'alimentation (18) 15.Raccorder respectivement le cordon d'ali- 17.Ouvrir le couvercle inférieur droit (26) du
dans le (petit) passage (19) et le câble du mentation (22) et le câble à signal (23) aux MFP.
signal (20) dans le (grand) passage (21) puis connecteurs (24) (25) du MFP. Déposer la courroie (27) de l'arbre (28) et
fermer le passage. 16. Reposer le couvercle (13) à l'aide de la vis déposer le couvercle inférieur droit (26).
(12) déposée à l'étape 10.
14.Pase el cable de alimentación (18) a través 15.Conecte el cable de alimentación (22) y el 17.Abra la cubierta frontal inferior (26) del MFP.
de la pestaña (pequeña) (19) y el cable de cable de señales (23) a los conectores (24) Quite la correa (27) del eje (28) y quite la
señales (20) a través de la pestaña (grande) (25) del MFP, respectivamente. cubierta frontal inferior (26).
(21) y, después, cierre la pestaña. 16.Vuelva a colocar la cubierta (13) usando el
tornillo (12) quitado en el paso 10.
14.Das Netzkabel (18) durch den Kantenschutz 15.Das Netzkabel (22) und das Signalkabel 17.Die untere rechte Abdeckung (26) am MFP
(klein) (19) und das Signalkabel (20) durch (23) an den entsprechenden Steckverbind- öffnen.
den Kantenschutz (groß) (21) führen und ern (24) (25) des MFP anschließen. Den Riemen (27) von der Welle (28)
dann den Kantenschutz schließen. 16.Die Abdeckung (13) mittels der in Schritt 10 abnehmen und dann die untere rechte
entfernten Schraube (12) wieder anbringen. Abdeckung (26) abnehmen.
14.Passare il cavo di alimentazione (18) attra- 15.Collegare il cavo di alimentazione (22) e il 17.Aprire il pannello destro inferiore (26)
verso il bordo (piccolo) (19) e il cavo del seg- cavo del segnale (23) rispettivamente ai sull'MFP.
nale (20) attraverso il bordo (grande) (21), e connettori (24) e (25) sull'MFP. Rimuovere la cinghietta (27) dall'asta (28) e
quindi chiudere il bordo. 16.Ricollocare il coperchio (13) utilizzando la quindi rimuovere il pannello destro inferiore
vite (12) rimossa nel passo 10. (26).
14.将 AC 电线 (18) 从包边孔（小）(19)，信号线 15.将 AC 电线 (22) 以及信号线 (23) 分别与主机 17.打开 MFP 主机的右下部盖板 (26)。
(20) 从包边孔（大）(21) 中分别穿过，关闭的接插件 (24)、(25) 连接。将带子 (27) 从轴 (28) 上拆除，拆下右下部
包边孔。 16.使用在步骤 10 中拆除的 1 颗螺丝 (12) 按原盖板 (26)。
样安装盖板 (13)。
14.AC 전선 (18) 을 에징（소）(19) 에 , 신호선 15.AC 전선 (22) 및 신호선 (23) 을 본체 커넥터 17.MFP 본체의 오른쪽 아래 커버 (26) 를 엽니
(20) 을 에징（대）(21) 에 각각 지나가게 하 (24), (25) 에 각각 접속합니다 . 다.
고 에징을 닫습니다 . 16.순서 10 에서 제거한 나사 (12) 1 개로 커버 스트라프 (27) 를 축 (28) 에서 떼어내 오른쪽
(13) 를 원래대로 부착합니다 . 아래 커버 (26) 를 제거합니다 .
14.AC 電線 (18) をエッジング（小） (19) に、信号 15.AC 電線 (22) および信号線 (23) を本体のコ 17.MFP 本体の右下カバー(26) を開く。
線 (20) をエッジング（大） (21) にそれぞれネクター(24)、(25) にそれぞれ接続する。ストラップ (27) を軸 (28) から外し、
右下カ
通し、エッジングを閉じる。 16.手順 10 で取り外したビス (12)1 本でカバーバー(26) を取り外す。
(13) を元通りに取り付ける。
5
30 D 30
29
31 H 31 H
18.Open the paper feeder right cover (29). 19.Fit the 3 hooks (30) on the intermediate paper conveying unit (D) into the 3 holes (31) in the
guide.
20.Secure the intermediate paper conveying unit (D) with the 2 screws (H).
18.Ouvrir le couvercle droit du bureau papier 19.Insérer les 3 crochets (30) de l'unité de transport du papier intermédiaire (D) dans les 3 trous (31)
(29). du guide.
20.Fixer l'unité de transport du papier intermédiaire (D) à l'aide des 2 vis (H).
18.Abra la cubierta derecha del alimentador de 19.Coloque los 3 ganchos (30) de la unidad de transporte de papel intermedia (D) en los 3 orificios
papel (29). (31) de la guía.
20.Asegure la unidad de transporte de papel intermedia (D) con los 2 tornillos (H).
18.Die rechte Abdeckung (29) des Papiere- 19.Die 3 Haken (30) an der eingesetzten Papierfördereinheit (D) in die 3 Öffnungen (31) in der Füh-
inzugs öffnen. rung einpassen.
20.Die eingesetzte Papierfördereinheit (D) mit den 2 Schrauben (H) sichern.
18.Aprire il pannello destro (29) dell'unità di ali- 19.Inserire i 3 ganci (30) sull'unità intermediale di trasporto carta (D) nei 3 fori (31) nella guida.
mentazione della carta. 20.Fissare l'unità intermediale di trasporto carta (D) con le 2 viti (H).
18.打开供纸盒的右部盖板 (29)。 19.将中间搬运单元 (D) 的 3 个卡扣 (30) 嵌入导向板的 3 个孔 (31) 中。

20.使用 2 颗螺丝 (H) 来固定中间搬运单元 (D)。
18.급지대 오른쪽 커버 (29) 를 엽니다 . 19.중간반송유니트 (D) 의 후크 (30) 3 개를 가이드 구멍 (31) 3 곳에 꽂습니다 .
20.나사 (H) 2 개로 중간반송유니트 (D) 를 고정합니다 .
18.ペーパーフィーダーの右カバー(29) を開 19.中間搬送ユニット (D) のフック (30)3 個をガイドの穴 (31)3 カ所にはめ込む。

く。 20.ビス (H)2 本で中間搬送ユニット (D) を固定する。
6
32
F
33 35
34
21.Connect the intermediate paper conveying 23.Insert the projection (33) on the wire cover 25.Turn the adjusters on each corner (35) until
unit connector (32). (F) into the hole (34) in the paper feeder and they reach the floor and then secure the
22.Attach the clamp (E) and secure the connec- install the wire cover (F). paper feeder.
tor wire. 24.Close the paper feeder right cover (29) and
replace the lower right cover (26) on the
MFP.
21.Raccorder le connecteur (32) de l'unité de 23.Insérer la saillie (33) du couvercle du câble 25.Faire tourner les dispositifs de réglage de
transport du papier intermédiaire. (F) dans le trou (34) du bureau papier et chacun des coins (35) jusqu'à ce qu'ils
22.Monter le collier (E) et fixer le câble du con- reposer le couvercle du câble (F). touchent le sol et fixer ensuite le bureau
necteur. 24.Fermer le couvercle droit du bureau papier papier.
(29) et reposer le couvercle inférieur droit
(26) sur le MFP.
21.Conecte el conector de la unidad de trans- 23.Inserte el resalto (33) de la cubierta para el 25.Gire los reguladores en cada esquina (35)
porte de papel intermedia (32). cable (F) en el orificio (34) del alimentador hasta que lleguen al piso y, a continuación,
22.Fije el sujetador (E) y asegure el cable del de papel e instale la cubierta para el cable asegure el alimentador de papel.
conector. (F).
24.Cierre la cubierta derecha del alimentador
de papel (29) y vuelva a colocar la cubierta
derecha inferior (26) en el MFP.
21.Den Steckverbinder (32) der eingesetzten 23.Die Nase (33) der Kabelabdeckung (F) in die 25.Die Einsteller an jeder Ecke (35) drehen, bis
Papierfördereinheit anschließen. Öffnung (34) des Papiereinzugs einsetzen sie den Boden berühren, und dann den
22.Die Klemme (E) anbringen und das Kabel und die Kabelabdeckung (F) anbringen. Papiereinzug sichern.
des Steckverbinders sichern. 24.Die rechte Abdeckung (29) des Papiere-
inzugs schließen und die untere rechte
Abdeckung (26) wieder am MFP einsetzen.
21.Collegare il connettore (32) dell'unità inter- 23.Inserire la sporgenza (33) del coperchio cavi 25.Ruotare i regolatori (35) presenti su ciascun
mediale di trasporto carta. (F) nel foro (34) nell'unità di alimentazione angolo finché vengano a contatto con il pavi-
22.Applicare il morsetto (E) e fissare il cavo del della carta ed installare il coperchio cavi (F). mento, e quindi fissare l’unità di alimentazi-
connettore. 24.Chiudere il pannello destro (29) dell'unità di one della carta.
alimentazione della carta e ricollocare il pan-
nello destro inferiore (26) sull'MFP.
21.连接中间搬运单元的接插件 (32)。 23.将电线盖板 (F) 的突出部 (33) 插入供纸盒的 25.转动四角上的调节器 (35) 直至与地面接触，
22.安装夹钳 (E)，以固定接插件电线。孔 (34) 中，安装电线盖板 (F)。然后再固定供纸盒
24.关闭供纸盒的右部盖板 (29)，按原样安装
MFP 主机的右下部盖板 (26)。
21.중간반송유니트의 커넥터 (32) 를 접속합니 23.전선커버 (F) 의 돌기 (33) 를 급지대의 구멍 25.네 곳의 어져스터 (35) 를 맨 밑에 닿을 위치
다. (34) 에 넣고 전선커버 (F) 를 부착합니다 . 까지 돌려 급지대를 고정합니다 .
22.클램프 (E) 를 부착 , 커넥터 전선을 고정합니 24.급지대 오른쪽 커버 (29) 를 닫고 , MFP 본체
다. 의 오른쪽 아래 커버 (26) 를 원래대로 부착
합니다 .
21.中間搬送ユニットのコネクター(32) を接続 23.電線カバー(F) の突起 (33) をペーパー 25.四隅のアジャスター(35) を床に接触する位

する。フィーダーの穴 (34) に入れて、電線カバー置まで回し、
ペーパーフィーダーを固定す
22.クランプ (E) を取り付け、
コネクター電線を (F) を取り付ける。る。
固定する。 24.ペーパーフィーダーの右カバー(29) を閉
じ、MFP 本体の右下カバー(26) を元通りに取
り付ける。
7
37
36
37
Setting the paper size plate and media type Changing paper size (metric specifications 1.Pull out the cassette of the paper feeder.
plate only) 2.Turn the front lock lever (36) 90° and remove
Fold the plates in half and insert them into the At shipment, Letter is set for inch models and A4 the front deck cursor (37).
size and media type slots respectively. For more is set for metric models. Use the procedure
details, refer to the operation guide. below to change the size to B5.
Réglage du plateau de format du papier et du Modification du format du papier (pour 1.Tirer le magasin du bureau papier vers soi.
plateau du type de média spécifications métriques seulement) 2.Faire tourner le levier de verrouillage avant
Rabattre à moitié les plateaux et les insérer À expédition, les modèles à mesure en pouces (36) de 90º et déposer le curseur de platine
respectivement dans les fentes du format et du sont réglés sur le format Letter et les modèles à avant (37).
type de média. Pour plus de détail, voir le mode mesure métrique sur le format A4. Pour passer
d'emploi. au format B5, procéder de la manière suivante.
Ajuste de la placa de tamaño de papel y la Cómo cambiar el tamaño de papel (sólo para 1.Abra el casete del alimentador de papel.
placa de tipo de medio las especificaciones métricas) 2.Gire la palanca de bloqueo frontal (36) 90º y
Pliegue las placas por la mitad e insértelas en En el momento de salida de fábrica, se config- quite el cursor frontal de la plataforma (37).
las ranuras de tamaño y tipo de medio respec- ura Carta para los modelos en pulgadas y A4
tivamente. Para obtener más información, con- para los modelos en sistema métrico. Siga este
sulte la Guía de uso. procedimiento para cambiar el tamaño a B5.
Einsetzen der Papierformatplatte und der Ändern des Papierformats (nur metrische Spe- 1.Ziehen Sie die Papierlade aus dem Papiere-
Medientypplatte zifikationen) inzug.
Die Platten halb zusammenklappen und in die Beim Werksversand ist bei Modellen mit Zollmaß 2.Den vorderen Verriegelungshebel (36) um
Öffnungen für Format bzw. Medientyp ein- das Format Letter voreingestellt und bei Modellen 90° drehen und den vorderen Konsole-Cur-
schieben. Näheres hierzu siehe Bedienungs- mit metrischem Maß das Format A4. sor (37) abnehmen.
anleitung. Das Format kann wie folgend auf B5 umge-
schaltet werden.
Impostazione della piastra di formato carta e Cambio del formato della carta (solo per le 1.Estrarre il cassetto dell’unità di alimentatore
della piastra del tipo di supporto specifiche metriche) della carta.
Piegare le piastre a metà e inserirle rispettiva- Al momento della spedizione, Letter è impostato 2.Ruotare la leva frontale di blocco (36) di 90°
mente negli slot per il formato e il tipo di sup- per le specifiche in pollici e A4 è impostato per e rimuovere il cursore frontale del deck (37).
porto. Per maggiori dettagli, fare riferimento alla le specifiche metriche. Usare la procedura
guida alle funzioni. riportata sotto per cambiare il formato a B5.
纸张尺寸托板和纸张种类托板的安装纸张尺寸更改（仅限公制规格） 1.拉出供纸工作台的供纸盒。

把托板对折后，分别插入纸张尺寸、种类标记插产品出厂时，英制规格设定为 Letter、公制规格 2.将前部锁定杆 (36) 旋转 90°，拆下堆纸板前
槽中。详情请参阅使用说明书。设定为 A4。要将尺寸更改为 B5 时，请按以下步骤部游标（37）。
进行操作。
용지크기 플레이트와 용지종류 플레이트의 세트 용지크기 변경（센치 사양만） 1.급지대 카세트를 빼 냅니다 .
플레이트를 2 곳 접어 크기 , 용지종류표시 슬롯 출하시 , 인치사양은 Letter, 센치사양은 A4 로 2.잠금레버 앞 (36) 을 90° 회전시켜 데크커서
에 각각 삽입합니다 . 상세는 사용설명서를 참조 . 설정되어 있습니다 . 크기를 B5 로 변경하는 경 앞（37）을 제거합니다 .
우에는 다음 순서를 진행해 주십시오 .
用紙サイズプレートと用紙種類プレートのセット用紙サイズ変更（センチ仕様のみ） 1.ペーパーフィーダーのカセットを引き出す。

プレートを 2 つ折りにし、サイズ、
用紙種表示ス出荷時、インチ仕様は Letter、センチ仕様は A4 2.ロックレバー前 (36) を 90° 回転させ、
デッ
ロットにそれぞれ挿入する。詳細は使用説明書に設定されています。サイズを B5 に変更する場キカーソル前
（37）を取り外す。
を参照。合は次の手順をおこなってください。
8
40 41
38
B5 42
Letter 39
A4
B5
Letter
37
A4
36 41
3.Move the front deck cursor (37) so that it is aligned with the size indicators on the top (39) and 6.Release the hook (41) and remove the deck
bottom (38) of the cassette. trailing edge cursor (42).
4.Turn the front lock lever (36) 90° to lock it.
5.Move the rear deck cursor (40) in the same way.
3.Déplacer le curseur de platine avant (37) de sorte qu'il soit aligné avec les indicateurs de format 6.Libérer le crochet (41) et déposer le curseur
en haut (39) et en bas (38) du tiroir. du bord arrière de la platine (42).
4.Faire tourner le levier de verrouillage avant (36) de 90º pour le verrouiller.
5.Déplacer le curseur de platine arrière (40) en procédant de la même manière.
3.Mueva el cursor frontal de la plataforma (37) para que quede alineado con las indicadores de 6.Libere el gancho (41) y quite el cursor del
tamaño de la parte superior (39) e inferior (38) del cajón. borde inferior de la plataforma (42).
4.Gire la palanca de bloqueo frontal (36) 90º para bloquearla.
5.Mueva el cursor trasero de la plataforma (40) de la misma forma.
3.Den vorderen Konsole-Cursor (37) so verschieben, dass er mit den Formatanzeigen oben (39) 6.Den Haken (41) lösen und den Hinterkante-
und unten (38) an der Kassette fluchtet. Cursor (42) der Konsole abnehmen.
4.Den vorderen Verriegelungshebel (36) zum Verriegeln um 90° drehen.
5.Den hinteren Konsole-Cursor (40) auf gleiche Weise verschieben.
3.Spostare il cursore frontale del deck (37) in modo che esso risulti allineato con gli indicatori di for- 6.Rilasciare il gancio (41) e rimuovere il cur-
mato sulla parte superiore (39) e inferiore (38) del cassetto. sore del bordo di uscita del deck (42).
4.Ruotare la leva frontale di blocco (36) di 90°, per bloccarla.
5.Spostare il cursore posteriore del deck (40) allo stesso modo.
3.移动堆纸板前部游标 (37)，使供纸盒下部的尺寸标记 (38) 与供纸盒上部的尺寸标记 (39) 对齐。 6.解除卡扣（41），拆下堆纸板后部游标 (42)。

4.将前部锁定杆 (36) 旋转 90° 以固定。
5.按同样方式移动后部堆纸板后部游标 (40)。
3.카세트 밑의 크기표시 (38) 와 카세트 위의 크기 표시 (39) 에 맞춰 데크커서 앞 (37) 을 이동시킵 6.후크（41）를 해제하고 데크 뒷단커서 (42)
니다 . 를 제거합니다 .
4.잠금레버 앞 (36) 을 90° 회전시켜 고정합니다 .
5.똑같이 데크커서 뒤 (40) 를 이동시킵니다 .
3.カセット下のサイズ表示 (38) とカセット上のサイズ表示 (39) に合わせてデッキカーソル前 6.フック（41）を解除し、デッキ後端カーソル

(37) を移動させる。 (42) を取り外す。
4.ロックレバー前 (36) を 90° 回転させ固定する。
5.同様にデッキカーソル後 (40) を移動させる。
9
45 43
40
46
0.5㨪1.5mm
42
44 37
B5
A4
7.Lift up the sub-cursor (43). Adjusting the cursor width

8.Align with the size indicator (44), engage the 1.Load paper in the cassettes.
hook (45) and install the deck trailing edge 2.If the gap between the front deck cursor (37) and the paper (46) is outside the 0.5 to 1.5 mm
cursor (42). range when the paper (46) is touching up against the rear deck cursor (40), perform the following
adjustment.
* A cursor width that is too small can hinder paper feeding, while a cursor width that is too large
can lead to problems such as skewed paper feed.
7.Lever le curseur secondaire (43). Réglage de la largeur du curseur

8.Aligner avec l'indicateur de format (44), 1.Charger les tiroirs en papier.
engager le crochet (45) et reposer le curseur 2.Si l'écartement entre le curseur de platine avant (37) et le papier (46) est hors des limites de 0,5
du bord arrière de la platine (42). à 1,5 mm quand le papier (46) touche le curseur de platine arrière (40), procéder au réglage sui-
vant.
* Une largeur trop faible du curseur risque d'empêcher l'entraînement du papier et une largeur
trop grande risque d'entraîner des problèmes du type entraînement du papier de biais.
7.Levante el cursor secundario (43). Cómo ajustar la anchura del cursor

8.Alinee con el indicador de tamaño (44), 1.Cargue papel en los cajones.
enganche el gancho (45) e instale el cursor 2.Si la separación entre el cursor frontal de la plataforma (37) y el papel (46) está fuera del rango de
del borde inferior de la plataforma. (42). 0,5 a 1,5 mm cuando el papel (46) toca el cursor trasero de la plataforma (40), haga el siguiente
ajuste.
* Una anchura del cursor demasiado pequeña puede impedir la alimentación de papel; una anchura
del cursor demasiado grande puede provocar problemas con la alimentación torcida de papel.
7.Den Unter-Cursor (43) anheben. Einstellen der Cursor-Breite

8.Auf die Formatanzeige (44) ausrichten, den 1.Papier in die Papierladen einlegen.
Haken (45) einsetzen und den Hinterkante- 2.Falls der Abstand zwischen dem vorderen Konsole-Cursor (37) und dem Papier (46) außerhalb
Cursor (42) der Konsole anbringen. des Bereichs 0,5 bis 1,5 mm liegt, wenn das Papier (46) am hinteren Konsole-Cursor (40) anliegt,
* Eine zu kleine Cursor-Breite kann den Papiereinzug behindern, wogegen eine zu große Cursor-
Breite verkanteten Papiereinzug und ähnliche Probleme verursachen kann.
7.Sollevare il cursore secondario (43). Regolazione della larghezza del cursore

8.Allineare con l'indicatore formato (44), fis- 1. Caricare carta nei cassetti.
sare il gancio (45) e installare il cursore del 2. Se lo spazio tra il cursore frontale del deck (37) e la carta (46) è fuori della gamma da 0,5 a 1,5 mm
bordo di uscita del deck (42). quando la carta (46) tocca il cursore postertiore del deck (40), eseguire la regolazione seguente.
* Una larghezza dei cursori troppo piccola può ostacolare l'alimentazione della carta, mentre unalar-
ghezza dei cursori troppo grande può essere causa di problemi, come ad esempio l'alimentazione obbli-
qua della carta.
7.抬起副游标 (43)。游标宽度的调节

8.对齐尺寸标记 (44)，将卡扣（45）嵌入以安装 1.在供纸盒中装入纸张。
堆纸板后部游标 (42)。 2.在堆纸板后部游标 (40) 与纸张 (46) 接触的状态下，如果堆纸板前部游标 (37) 与纸张 (46) 的间
隙超出了 0.5 ～ 1.5mm 的范围，须进行以下调节。
※ 如果游标宽度过小，可能造成不供纸，游标宽度过大，则可能发生歪斜进纸等情况。
7.서브커서 (43) 를 세웁니다 . 커서 폭 조정

8.크기표시 (44) 에 맞춰 후크（45）를 판벽데 1.카세트에 용지를 장착합니다 .
크 후단커서 (42) 를 부착합니다 . 2.데크커서 뒤 (40) 에 용지 (46) 가 접하고 있는 상태에서 데크커서 앞 (37) 과 용지 (46) 의 틈이
0.5 ～ 1.5mm 의 범위외의 경우에는 이하의 조정을 합니다 .
※ 커서 폭이 작으면 무급지 , 커서 폭이 크면 경사급지 등이 발생할 가능성이 있습니다 .
7.サブカーソル (43) を起こす。カーソル幅の調整

8.サイズ表示 (44) に合わせて、
フック（45）を 1.カセットに用紙をセットする。
はめデッキ後端カーソル (42) を取り付け 2.デッキカーソル後 (40) に用紙 (46) が接している状態で、デッキカーソル前 (37) と用紙 (46) の
る。隙間が 0.5 ～ 1.5mm の範囲外の場合は、以下の調整をおこなう。
※ カーソル幅が小さいと無給紙、カーソル幅が大きいと斜め給紙などが発生する可能性がある。
10
48
37
37
47
3.Insert a Philips-head screwdriver into the 2 long slots (47) in the front deck cursor (37) and loosen 4.Retighten the 2 adjusting screws (48).
the 2 adjusting screws (48). Then move the front deck cursor (37). 5.Check that the gap between the front deck
cursor (37) and the paper is between 0.5
and 1.5 mm.
3.Insérer un tournevis cruciforme dans les 2 longues fentes (47) du curseur de platine avant (37) et 4.Resserrer les 2 vis de réglage (48).
desserrer les 2 vis de réglage (48). Déplacer ensuite le curseur de platine avant (37). 5.Vérifier que l'écartement entre le curseur de
platine avant (37) et le papier est entre 0,5 et
1,5 mm.
3.Inserte un destornillador de cabeza Philips en las dos ranuras largas (47) en el cursor frontal de 4.Vuelva a apretar los 2 tornillos de ajuste
la plataforma (37) y afloje los 2 tornillos de ajuste (48). Después, mueva el cursor frontal de la (48).
plataforma (37). 5.Verifique que la separación entre el cursor
frontal de la plataforma (37) y el papel sea
de entre 0,5 y 1,5 mm.
3.Einen Kreuzschlitzschraubendreher in die 2 langen Öffnungen (47) im vorderen Konsole-Cursor 4.Die 2 Einstellschrauben (48) wieder anzie-
(37) stecken und die 2 Einstellschrauben (48) lösen. Danach den vorderen Konsole-Cursor (37) hen.
verschieben. 5.Vergewissern Sie sich, dass der Abstand
zwischen dem vorderen Konsole-Cursor
(37) und dem Papier im Bereich 0,5 bis 1,5
mm liegt.
3.Inserire un cacciavite con testa a croce tipo Philips nelle 2 fessure lunghe (47) nel cursore fron- 4.Ristringere le 2 viti di regolazione (48).
tale del deck (37) e allentare le 2 viti di regolazione (48). Quindi spostare il cursore frontale del 5.Controllare che lo spazio tra il cursore fron-
deck (37). tale del deck (37) e la carta sia compreso
nella gamma tra 0,5 e 1,5 mm.
3.将十字螺丝刀从堆纸板前部游标 (37) 的 2 处长孔 (47) 处插入，拧松 2 颗调节螺丝 (48)，移动堆 4.拧紧 2 颗调节螺丝 (48)。
纸板前部游标 (37)。 5.确认堆纸板前部游标 (37) 与纸张的间隙在
0.5 ～ 1.5mm 的范围内。
3.데크커서 앞 (37) 2 곳의 긴 구멍 (47) 에서 플러스 드라이버를 넣어 조정나사 (48) 2 개를 느슨하 4.조정나사 (48) 2 개를 조입니다 .
게 하고 데크커서 앞 (37) 을 이동시킵니다 . 5.데크커서 앞 (37) 과 용지의 틈이 0.5 ～ 1.5
mm 범위내가 되어 있는 것을 확인합니다 .
3.デッキカーソル前 (37) の 2 箇所の長穴 (47) からプラスドライバー挿入し、調整ビス (48)2 本を 4.調整ビス (48)2 本を締め付ける。

緩め、
デッキカーソル前 (37) を移動させる。 5.デッキカーソル前 (37) と用紙の隙間が 0.5
～ 1.5mm の範囲内になっていることを確認
する
11
㧙
b
㧗
a c d
Adjusting the leading edge timing

The reference value for the leading edge timing is 20 ±1.5 mm at position (b) in the correct image (a). If the timing is outside this range, perform the fol-
lowing adjustment.
1.Set maintenance mode U034, select LSU Out Left and Cassette(L)
Test pattern (c): Increase the setting value. Test pattern (d): Decrease the setting value.
Réglage de la synchronisation du bord de tête

La valeur de référence de la synchronisation du bord de tête est de 20 ±1,5 mm à la position (b) d'une image correcte (a). Si la synchronisation est hors
de cette plage, procéder au réglage suivant.
1.Passer en mode maintenance U034, sélectionner LSU Out Left et Cassette(L).
Mire d' essai (c): Augmentez la valeur de réglage. Mire d' essai (d): Diminuez la valeur de réglage.
Cómo ajustar la sincronización del borde superior

El valor de referencia de la sincronización del borde superior es de 20 ±1,5 mm en la posición (b) de la imagen correcta (a). Si la sincronización estuviera
1.Entre al modo de mantenimiento U034, seleccione LSU Out Left y Cassette(L).
Patrón de prueba (c): Aumente el valor de configuración. Patrón de prueba (d): Reduzca el valor de configuración.
Einstellen des Vorderkanten-Timing

Der Bezugswert des Vorderkanten-Timing ist 20 ±1,5 mm an Position (b) des korrekten Bilds (a). Falls das Timing außerhalb dieses Bereichs liegt, ist fol-
gende Einstellung vorzunehmen.
1.Schalten Sie in den Wartungsmodus U034, wählen Sie LSU Out Left und Cassette(L).
Testmuster (c): Den Einstellwert erhöhen. Testmuster (d): Den Einstellwert verringern.
Regolazione della sincronizzazione del bordo principale

Il valore di riferimento per la sincronizzazione del bordo principale è 20 ±1,5 mm alla posizione (b) nell'immagine corretta (a). Se la sincronizzazione è
all'infuori di questa gamma, effettuare la regolazione seguente.
1.Impostare la modalità manutenzione U034, selezionare LSU Out Left e Cassette(L).
Modello di prova (c): Aumentare il valore dell'impostazione. Modello di prova (d): Diminuire il valore dell'impostazione.
前端对位调节
前端对位的基准值在矫正图像 (a) 的 (b) 位置为 20±1.5mm。超出该范围时，须进行以下调节。
1.设置维护模式 U034，选择 LSU Out Left、Cassette(L)。
测试图案 (c) ：调高设定值。测试图案 (d) ：调低设定值。
선단 타이밍 조정
선단 타이밍은 적정화상 (a) 의 (b) 위치에서 기준치는 20±1.5mm. 여기에서 벗어나는 것은 이하의 조정을 합니다 .
1.메인터넌스 모드 U034 를 세트하고 LSU Out Left, Cassette(L) 을 선택합니다 .
테트스 패턴 (c) ：설정치를 높입니다 . 테스트 패턴 (d) ：설정치를 내립니다 .
先端タイミング調整
先端タイミングは、適正画像 (a) の (b) の位置で基準値は 20±1.5mm。これから外れるときは以下の調整をおこなう。
1.メンテナンスモード U034 をセットし、LSU Out Left、Cassette(L) を選択する。
テストパターン (c) ：設定値を上げる。　テストパターン (d) ：設定値を下げる。
12
f
㧙㧗
e g h
Adjusting the center line

The reference value for the center line is ±0.5 mm or less at position (f) in the correct image (e). If the center line position is outside this range, perform the
following adjustment.
1.Set maintenance mode U034, select LSU Out Left and Cassette3 or Cassette4.
Test pattern (g): Increase the setting value. Test pattern (h): Decrease the setting value.
Réglage de l'axe
La valeur de référence pour l'axe est de ±0,5 mm ou moins à la position (f) d'une image correcte (e). Si la position de l'axe est hors de cette plage,
effectuez le réglage suivant.
1.Passer en mode maintenance U034, sélectionner LSU Out Left et Cassette3 ou Cassette4.
Mire d' essai (g): Augmentez la valeur de réglage. Mire d' essai (h): Diminuez la valeur de réglage.
Ajuste de la línea central
El valor de referencia de la línea central es de ±0,5 mm o menor, en la posición (f) de la imagen correcta (e). Si la posición de la línea central estuviera
1.Entre al modo de mantenimiento U034, seleccione LSU Out Left y Cassette3 o Cassette4.
Patrón de prueba (g): Aumente el valor de configuración. Patrón de prueba (h): Reduzca el valor de configuración.
Einstellen der Mittenlinie

Der Bezugswert für die Mittenlinie ist ±0,5 mm oder weniger an Position (f) des korrekten Bilds (e). Falls die Mittenlinie außerhalb dieses Bereichs liegt,
1.Schalten Sie in den Wartungsmodus U034, wählen Sie LSU Out Left und Cassette3 oder Cassette4.
Testmuster (g): Den Einstellwert erhöhen. Testmuster (h): Den Einstellwert verringern.
Regolazione della linea centrale

Il valore di riferimento per la linea centrale è ±0,5 mm o inferiore alla posizione (f) nell'immagine corretta (e). Se la posizione della linea centrale è all'infu-
ori di questa gamma, effettuare la regolazione seguente.
1.Impostare la modalità manutenzione U034, selezionare LSU Out Left e Cassette3 o Cassette4.
Modello di prova (g): Aumentare il valore dell'impostazione. Modello di prova (h): Diminuire il valore dell'impostazione.
中心线调节
中心线的基准值在矫正图像 (e) 的 (f) 位置为 ±0.5mm 以内。超出该范围时，须进行以下调节。
1.设置维护模式 U034，选择 LSU Out Left、Cassette3 或 Cassette4。
测试图案 (g) ：调高设定值。测试图案 (h) ：调低设定值。
센터라인 조정
센터라인은 적정화상 (e) 의 (f) 위치에서 기준치는 ±0.5mm 이내 . 여기에서 벗어나는 것은 이하의 조정을 합니다 .
1.메인터넌스 모드 U034 를 세트하고 LSU Out Left, Cassette3 또는 Cassette4 를 선택합니다 .
테트스 패턴 (g) ：설정치를 높입니다 . 테스트 패턴 (h) ：설정치를 내립니다 .
センターライン調整
センターラインは、適正画像 (e) の (f) の位置で基準値は ±0.5mm 以内。これから外れるときは以下の調整をおこなう。
1.メンテナンスモード U034 をセットし、LSU Out Left、Cassette3 または Cassette4 を選択する。
テストパターン (g) ：設定値を上げる。　テストパターン (h) ：設定値を下げる。
13
1000-SHEETS FINISHER
A F
C D
E
G H I K
E. Connecting plate........................................ 1 Be sure to remove any tape and/or cushioning

English
F. Wire guide.................................................. 1 material from supplied parts.
Supplied parts G. Eject guide ................................................. 1
A. Document finisher...................................... 1 H. Staple cartridge.......................................... 1
B. Eject tray.................................................... 1 I. M4 × 8 screw ............................................. 3
C. Upper earth plate....................................... 1 J. M4 × 30 screw ........................................... 2
D. Lower earth plate....................................... 1 K. M4 × 10 screw (black) ............................... 1
E. Plaque de connexion ................................. 1 Veillez à retirer les morceaux de bande adhé-

Français
F. Guide câble................................................ 1 sive et/ou les matériaux de rembourrage des
Pièces fournies G. Guide d'éjection ......................................... 1 pièces fournies.
A. Retoucheur de document .......................... 1 H. Cartouche d’agrafes .................................. 1
B. Bac d'éjection ............................................ 1 I. Vis M4 × 8.................................................. 3
C. Prise de terre supérieure ........................... 1 J. Vis M4 × 30................................................ 2
D. Prise de terre inférieure ............................. 1 K. Vis M4 × 10 (noire) .................................... 1
E. Placa de conexión ..................................... 1 Asegúrese de despegar todas las cintas y/o

Español
F. Guía para el cable ..................................... 1 material amortiguador de las partes suministra-
Partes suministradas G. Guía de salida............................................ 1 das.
A. Finalizador de documentos ....................... 1 H. Cartucho de grapas ................................... 1
B. Bandeja de salida ...................................... 1 I. Tornillo M4 × 8 ........................................... 3
C. Placa de conexión a tierra superior ........... 1 J. Tornillo M4 × 30 ......................................... 2
D. Placa de conexión a tierra inferior ............. 1 K. Tornillo M4 × 10 (negro)............................. 1
E. Verbindungsplatte ...................................... 1 Entfernen Sie Klebeband und/oder Dämpfungs-

Deutsch
F. Kabelführung ............................................. 1 material vollständig von den mitgelieferten
Gelieferte Teile G. Auswerfführung.......................................... 1 Teilen.
A. Dokument Finishers................................... 1 H. Heftklammermagazin................................. 1
B. Auswerffach ............................................... 1 I. M4 × 8 Schraube ....................................... 3
C. Obere Grundplatte ..................................... 1 J. M4 × 30 Schraube ..................................... 2
D. Untere Grundplatte .................................... 1 K. M4 × 10 Schraube (schwarz)..................... 1
E. Piastra di connessione............................... 1 Accertarsi di rimuovere tutti i nastri adesivi e/o il

Italiano
F. Guida cavi.................................................. 1 materiale di imbottitura dalle parti fornite.
Parti di fornitura G. Guida di espulsione ................................... 1
A. Finitrice di documenti................................. 1 H. Cartuccia punti metallici............................. 1
B. Vassoio di espulsione ................................ 1 I. Vite M4 × 8................................................. 3
C. Piastra di messa a terra superiore............. 1 J. Vite M4 × 30............................................... 2
D. Piastra di messa a terra inferiore............... 1 K. Vite M4 × 10 (nera) .................................... 1
简体中文 E. 连接板 ...............................1 K. M4×10 螺丝（黒）......................1

F. 电线导向板 ...........................1
附属品 G. 排纸导向板 ..........................1 如果附属品上带有固定胶带，缓冲材料时务必揭
A. 装订器............................... 1 H. 装订针盒 .............................1 下。
B. 排纸托盘............................. 1 I. M4×8 螺丝 ............................3
C. 上部接地板........................... 1 J. M4×30 螺丝 ...........................2
D. 下部接地板........................... 1
한국어 E. 연결판 .............................................. 1 K. 나사 M4×10（흑）............................... 1

F. 전선 가이드....................................... 1
동봉품 G. 배출 가이드 ....................................... 1 동봉품에 고정 테이프 , 완충재가 붙어 있는 경
A. 문서 피니셔........................................ 1 H. 스테이플 카트리지.............................. 1 우에는 반드시 제거할 것 .
B. 배출 트레이........................................ 1 I. 나사 M4×8......................................... 3
C. 접지판 상........................................... 1 J. 나사 M4×30 ....................................... 2
D. 접지판 하........................................... 1
日本語 E. 連結板 ...............................1 同梱品に固定テープ、緩衝材がついている場合

F. 電線ガイド .......................... 1 は、
必ず取り外すこと。
同梱品 G. 排出ガイド ..........................1
A. ドキュメントフィニッシャー........... 1 H. ステープルカートリッジ .............. 1
B. 排出トレイ........................... 1 I. ビス M4×8 ............................3
C. アース板上........................... 1 J. ビス M4×30 ...........................2
D. アース板下........................... 1 K. ビス M4×10
（黒）.......................1
1
B A
1 2
NOTICE Procedure 1.Install by inserting the 2 hooks (1) on the

The Attachment Kit (AK-730) must be installed Before installing the document finisher, make back of the eject tray (B) into the holes (2) in
before the document finisher is installed. sure that the MFP’s main power switch is turned the document finisher (A) lift.
off and that its power cord is unplugged from the
power outlet.
AVIS Procédure 1.Procéder en insérant les 2 crochets (1) au

Le gabarit de fixation (AK-730) doit être en Avant d’installer le retoucheur de document, dos du bac d'éjection (B) dans les trous (2)
place avant de procéder à l'installation du retou- s’assurer que l’interrupteur d’alimentation princi- du dispositif de levage du retoucheur de
cheur de document. pal du MFP est hors tension et que le cordon document (A).
d’alimentation est débranché de la prise
secteur.
AVISO Procedimiento 1.Instale insertando los 2 ganchos (1) de la

El Kit de instalación (AK-730) debe instalarse Antes de instalar el finalizador de documentos, parte posterior de la bandeja de salida (B)
antes de instalar el finalizador de documentos. asegúrese de que el interruptor principal de la en los orificios (2) del elevador del finaliza-
alimentación de la MFP esté desconectado y dor de documentos (A).
que su cable de alimentación esté desenchu-
fado de la toma de corriente.
HINWEIS Verfahren 1.Setzen Sie die 2 Haken (1) zur Befestigung

Das Gerätezusatz (AK-730) muss installiert Vor dem Einbau des Dokument-Finishers muss an der Rückseite des Auswerffachs (B) in
werden, bevor man den Dokument-Finisher der MFP-Hauptschalter aktiviert, und das Netzk- die Öffnungen (2) an der Hebeplatte (A) des
installiert. abel von der Steckdose abgezogen sein. Dokument-Finishers ein.
NOTIFICA Procedura 1.Installare inserendo i 2 ganci (1) sul retro del

Il kit accessorio (AK-730) deve essere installato Prima di installare la finitrice di documenti, vassoio di espulsione (B) nei fori (2) sul soll-
prima che sia installata la finitrice di documenti. assicurarsi che l’interruttore principale della evatore della finitrice di documenti (A).
MFP sia spento e che il cavo di alimentazione
non sia inserito nella presa.
注意安装步骤 1.将排纸托盘排 (B) 内侧的 2 个卡扣 (1) 装入

安装装订器之前，必须先安装连接组件（AK- 安装装订器时，必须事先关闭 MFP 主机的主电源装订器 (A) 的升降板的孔 (2) 中。
730)。开关，并拔下电源插头后再进行作业。
주의 장착순서 1.배출 트레이 (B) 의 후면 후크 (1) 2 개를 문

문서 피니셔를 장착하기 전에 연결킷（AK-730) 문서 피니셔를 장착할 때에는 반드시 MFP 본체 서 피니셔 (A) 의 승강판 구멍 (2) 에 넣고 장
의 장착을 선행할 것 . 의 주 전원 스위치를 OFF 로 하고 전원 플러그 착합니다 .
를 빼고 작업을 할 것 .
注意取付手順 1.排出トレイ (B) の裏側のフック (1)2 個をド

ドキュメントフィニッシャーを取り付ける前ドキュメントフィニッシャーを取り付ける際キュメントフィニッシャー(A) の昇降板の
に、
アタッチメントキット（AK-730) の取り付けは、
必ず MFP 本体の主電源スイッチを OFF にし、穴 (2) に入れて、取り付ける。
をおこなうこと。電源プラグを外して作業をおこなうこと。
2
C E
3
G
I
D 3
2.Secure the upper earth plate (C) and lower 3.Install the eject guide (G) by fitting the 2 4.Attach the connecting plate (E) to the MFP
earth plate (D) with M4 × 8 screws (I). eject guide pins (3) into the holes in the MFP. using 2 M4 × 30 screws (J).
2.Fixer la plaque de terre supérieure (C) et la 3.Installer le guide d'éjection (G) en insérant 4.Fixer la plaque de connexion (E) au MFP à
plaque de terre inférieure (D) à l'aide des vis les 2 ergots du guide d'éjection (3) dans les l'aide de 2 vis M4 × 30 (J).
M4 × 8 (l). trous du MFP.
2.Asegure la placa de conexión a tierra supe- 3..Instale la guía de salida (G) encajando los 2 4.Fije la placa de conexión (E) a la MFP medi-
rior (C) y la placa de conexión a tierra infe- pasadores de la guía de salida (3) en los ori- ante 2 tornillos M4 × 30 (J).
rior (D) con tornillos M4 × 8 (I). ficios de la MFP.
2.Befestigen Sie die obere Grundplatte (C) 3.Bringen Sie die Auswerfführung (G) an, 4.Bringen Sie die Verbindungsplatte (E) mit 2
und die untere Grundplatte (D) mit M4 × 8 indem Sie die 2 Auswerfführungsstifte (3) in M4 × 30 Schrauben (J) am MFP an.
Schrauben (I). die Öffnungen des MFP stecken.
2.Fissare la piastra di messa a terra superiore 3.Installare la guida di espulsione (G) inser- 4.Applicare la piastra di connessione (E)
(C) e la piastra di messa a terra inferiore (D) endo i 2 perni (3) della guida di espulsione all’MFP utilizzando le 2 viti M4 × 30 (J).
con le viti M4 × 8 (I). nei fori dell'MFP.
2.将上部接地板 (C) 与下部接地板 (D) 各自使 3.将排纸导向板 (G) 的 2 根销钉 (3) 插入 MFP 4.使用 2 颗 M4×30(J) 螺丝将连接板 (E) 安装
用 M4×8(I) 螺丝进行固定。主机的孔中。到 MFP 主机上。
2.접지판 상 (C) 과 접지판 하 (D) 를 각각 나사 3.배출 가이드 (G) 의 핀 (3) 2 개를 MFP 본체 4.연결판 (E) 을 나사 M4×30(J) 2 개로 MFP
M4×8(I) 로 고정합니다 . 구멍에 꽂아 장착합니다 . 본체에 장착합니다 .
2.アース板上 (C) とアース板下 (D) をそれぞ 3.排出ガイド (G) のピン (3)2 本を MFP 本体の 4.連結板 (E) をビス M4×30(J)2 本で、MFP 本
れビス M4×8(I) で固定する。穴に差し込み取り付ける。体に取り付ける。
3
E
4 8
5
8
5.Remove the tape and remove the rear cover 6.Remove the screw (5) and pull the lock 7.Insert the 2 pins (8) on the connecting plate
(4). frame (6) outwards. (E) into the document finisher connecting
The connecting holes (7) can now be seen. holes (7) to connect the document finisher to
the MFP.
* If you cannot connect the document fin-
isher, adjust the height as described on page
7.
5.Enlever la bande adhésive et déposer le 6.Déposer la vis (5) et tirer le bâti de verrouil- 7.Insérer les 2 ergots (8) de la plaque de con-
couvercle arrière (4). lage (6) vers l'extérieur. Les trous de raccor- nexion (E) dans les trous de raccordement
dement (7) sont maintenant visibles. du retoucheur de document (7) pour con-
necter le retoucheur de document au MFP.
* S'il s'avère impossible de connecter le
retoucheur de document, en régler la hau-
teur comme décrit en page 7.
5.Quite la cinta y la cubierta posterior (4). 6.Quite el tornillo (5) y tire de la carcasa de 7.Inserte los 2 pasadores (8) de la placa de
bloqueo (6) hacia fuera. Ahora se ven los conexión (E) en los orificios de conexión del
orificios de conexión (7). finalizador de documentos (7) para conec-
tarlo a la MFP.
* Si no puede conectar el finalizador de doc-
umentos, ajuste la altura como se describe
en la página 7.
5.Entfernen Sie das Band und die hintere 6.Entfernen Sie die Schraube (5) und ziehen 7.Stecken Sie die 2 Stifte (8) an der Verbind-
Abdeckung (4). Sie den Fixierrahmen (6) nach außen her- ungsplatte (E) in die Verbindungsöffnungen
aus. Die Verbindungsöffnungen (7) sind nun (7) des Dokument-Finishers, um den Doku-
sichtbar. ment-Finisher mit dem MFP zu verbinden.
* Falls Sie den Dokument-Finisher nicht
anschließen können, sollten Sie die Höhe
wie auf Seite 7 beschrieben einstellen.
5.Rimuovere il nastro e quindi rimuovere il 6.Rimuovere la vite (5) e tirare il telaio di bloc- 7.Inserire i 2 perni (8) della piastra di connes-
coperchio posteriore (4). caggio (6) verso l'esterno. È possibile ora sione (E) nei fori di connessione (7) della
vedere i fori di connessione (7). finitrice di documenti, per collegare la fini-
trice di documenti all’MFP.
* Se non è possibile collegare la finitrice di
documenti, regolare l’altezza come descritto
a pagina 7.
5.拆除胶带，拆下后盖板 (4)。 6.拆除 1 颗螺丝 (5)，将锁框 (6) 向外拉出。可 7.将连接板 (E) 的 2 根销钉 (8) 插入装订器的
以看到连接用的孔 (7)。连接用孔 (7)，以将装订器与 MFP 主机连接。
※ 如果无法连接，请进行 P7 的 “ 高度调节
”。
5.테이프를 제거하고 후면커버 (4) 를 떼어 냅 6.나사 (5) 1 개를 빼고 잠금 프레임 (6) 을 앞 7.연결판 (E) 의 핀 (8) 2 개를 문서 피니셔의
니다 . 으로 뺍니다 . 연결용 구멍 (7) 이 보입니다 . 연결용 구멍 (7) 에 삽입하고 , 문서 피니셔를
MFP 본체에 접속합니다 .
※ 연결할 수 없는 경우에는 P7 의「높이조
정」을 할 것 .
5.テープを外し、後カバー(4) を取り外す。 6.ビス (5)1 本を外し、ロックフレーム (6) を 7.連結板 (E) のピン (8)2 本をドキュメント
手前に引く。フィニッシャーの連結用の穴 (7) に挿入し
連結用の穴 (7) が見える。て、ドキュメントフィニッシャーを MFP 本体
に接続する。
※ 連結できない場合は、 P7 の「高さ調整」を
行う。
4
F
9
10
6
8.Push the lock frame (6) in fully so that the 10.Install the wire guide (F) using the M4 × 8 11.Pass the signal line (9) through the wire
lock frame ribs fit into the pin slots. screw (I). guide (F) and connect it to the connector
9.Secure the lock frame (6) using the screw (10) on the MFP.
(5) removed in step 6.
8.Pousser à fond le bâti de verrouillage (6) de 10.Installer le guide câble (F) à l'aide d'une vis 11.Faire passer la ligne d'interconnexion (9)
sorte que les nervures du bâti de verrouil- M4 × 8 (l). dans le guide câble (F) et la raccorder au
lage pénètrent dans les encoches des connecteur (10) sur le MFP.
ergots.
9.Fixer le bâti de verrouillage (6) à l'aide de la
vis (5) déposée à l'étape 6.
8.Presione la carcasa de bloqueo (6) comple- 10.Instale la guía para el cable (F) por medio 11.Pase la línea de señales (9) a través de la
tamente hacia dentro para que sus nervadu- del tornillo M4 × 8 (I). guía para el cable (F) y conéctela al conec-
ras encajen en las ranuras de los tor (10) de la MFP.
pasadores.
9.Asegure la carcasa de bloqueo (6) por
medio del tornillo (5) quitado en el paso 6.
8.Drücken Sie den Fixierrahmen (6) ganz ein, 10.Bringen Sie die Kabelführung (F) mit der M4 11.Führen Sie die Signalleitung (9) durch die
damit die Fixierrahmenrippen in die × 8 Schraube (I) an. Kabelführung (F) und schließen Sie sie am
Stiftschlitze greifen. Steckverbinder (10) des MFP an.
9.Befestigen Sie den Fixierrahmen (6) mit der
in Schritt 6 entfernten Schraube (5).
8.Spingere completamente il telaio di bloccag- 10.Installare la guida cavi (F) utilizzando la vite 11.Far passare il cavo del segnale (9) attra-
gio (6) in modo che i rilievi del telaio di bloc- M4 × 8 (I). verso la guida cavi (F) e collegarlo al connet-
caggio si inseriscano nelle scanalature dei tore (10) sull’MFP.
perni.
9.Fissare il telaio di bloccaggio (6) utilizzando
la vite (5) rimossa nel passo 6.
8.将锁框 (6) 推入到底，使锁框的肋片嵌入销 10.使用 1 颗 M4×8(I) 螺丝来安装电线导向板 11.将信号线 (9) 在电线导向板 (F) 上配线，与
钉的沟槽内。 (F)。 MFP 主机的接插件 (10) 连接。
9.使用在步骤 6 中取下的 1 颗螺丝（5）来固定
锁框（6）。
8.잠금 프레임 (6) 을 안으로 밀고 핀의 홈에 10.전선 가이드 (F) 를 나사 M4×8(I) 1 개로 장 11.신호선 (9) 을 전선 가이드 (F) 에 배선하고
잠금 프레임 RIB 를 끼워 넣습니다 . 착합니다 . MFP 본체의 커넥터 (10) 에 접속합니다 .
9.순서 6 에서 뺀 나사（5）1 개로 잠금 프레임
（6）을 고정합니다 .
8.ロックフレーム (6) を奥へ押して、ピンの溝 10.電線ガイド (F) をビス M4×8(I)1 本で取り 11.信号線 (9) を電線ガイド (F) に配線し、
MFP
にロックフレームのリブをはめ込む。付ける。本体のコネクター(10) に接続する。
9.手順 6 で外したビス
（5）1 本で、
ロックフ
レーム（6）を固定する。
5
4
H
11 12
12.Install the back cover (4) using the M4 × 10 13.Install the interface cover (11)* on the MFP. 14.Open the document finisher front cover (12)
screw (K). * The cover removed while installing the AK- and install the staple cartridge (H).
730. 15.Close the front cover (12).
12.Reposer le couvercle arrière (4) à l'aide des 13.Reposer le couvercle d'interface (11)* sur le 14.Ouvrir le couvercle avant du retoucheur de
vis M4 × 10 (K). MFP. document (12) et installer la cartouche
* Le couvercle a été déposé à l'installation d'agrafes (H).
de l'AK-730. 15.Refermer le couvercle avant (12).
12.Instale la cubierta posterior (4) por medio del 13.Instale la cubierta de la interfaz (11)* en la 14.Abra la cubierta frontal del finalizador de
tornillo M4 × 10 (K). MFP. documentos (12) e instale el cartucho de
* La cubierta quitada durante la instalación grapas (H).
del AK-730. 15.Cierre la cubierta frontal (12).
12.Bringen Sie die hintere Abdeckung (4) mit 13.Bringen Sie die Schnittstellenabdeckung 14.Öffnen Sie die vordere Abdeckung (12) des
der M4 × 10 Schraube (K) an. (11)* am MFP an. Dokument-Finishers und setzen Sie das
* Die beim Installieren des AK-730 entfernte Heftklammermagazin (H) ein.
Abdeckung. 15.Schließen Sie die vordere Abdeckung (12).
12.Installare il pannello anteriore (4) utilizzando 13.Installare la copertura di interfaccia (11)* 14.Aprire il pannello anteriore della finitrice di
la vite M4 × 10 (K). sull’MFP. documenti (12) e installare la cartuccia punti
* La copertura rimossa durante l'installazi- metallici (H).
one dell'AK-730. 15.Chiudere il pannello anteriore (12).
12.使用 M4×10(K) 螺丝来安装后盖板（4）。 13.将接口盖板 (11)* 安装到 MFP 主机上。 14.打开装订器的前盖板 (12)，安装装订针盒
* 安装 AK-730 时取下的盖板。 (H)。
15.关闭前盖板 (12)。
12.나사 M4×10(K) 으로 후면 커버
（4）
를 장착 13.MFP 본체에 인터페이스 커버 (11)* 를 장착 14.문서 피니셔의 전면커버 (12) 를 열고 스테이
합니다 . 합니다 . 플 카트리지 (H) 를 장착합니다 .
*AK-730 설치 시에 떼어내었던 커버 . 15.전면커버 (12) 를 닫습니다 .
12.ビス M4×10(K) で後カバー（4）を取り付け 13.MFP 本体にインターフェイスカバー(11)* を 14.ドキュメントフィニッシャーの前カバー

る。取り付ける。 (12) を開き、ステープルカートリッジ (H)
*AK-730 設置時に取り外したカバー。を取り付ける。
15.前カバー(12) を閉じる。
6
8
a b b a b
a
8 7
13
Adjusting the height Compliant: The diameter (a) of the pin (8) is within the height range (b) of the curved section (13).
1.Check that the respective heights of the pins Non-compliant: The diameter (a) of the pin (8) is extends beyond the height range (b) of the curved
(8) on the connecting plate installed on the section (13).
MFP and the connecting holes (7) on the If the heights are non-compliant, use the procedure below to adjust the height.
document finisher comply with the standards
below.
Réglage de la hauteur Bon : Le diamètre (a) de l'ergot (8) est dans les limites de hauteur (b) de la partie courbée (13).
1.Vérifier que la hauteur des différents ergots Mauvais : Le diamètre (a) de l'ergot (8) dépasse les limites de hauteur (b) de la partie courbée (13).
(8) de la plaque de connexion installée sur le Si la hauteur n'est pas conforme, l'ajuster en procédant comme indiqué ci-dessous.
MFP et les trous de raccordement (7) sur le
retoucheur de document sont conformes à
ce qui suit.
Ajuste de la altura Cumple: el diámetro (a) del pasador (8) está dentro del rango de altura (b) de la sección curvada
1.Compruebe si las alturas respectivas de los (13).
pasadores (8) de la placa de conexión insta- No cumple: el diámetro (a) del pasador (8) sobrepasa el rango de altura (b) de la sección curvada
lada en la MFP y los orificios de conexión (7) (13).
del finalizador de documentos cumplen con Si las alturas no cumplen con las especificaciones, utilice el siguiente procedimiento para ajustar la
los siguientes estándares. altura.
Einstellen der Höhe Korrekt: Der Durchmesser (a) des Stifts (8) befindet sich im Höhenbereich (b) des Kurvenabschnitts
1.Vergewissern Sie sich, dass die jeweilige (13).
Höhe der Stifte (8) der am MFP ange- Nicht korrekt: Der Durchmesser (a) des Stifts (8) ragt über den Höhenbereich (b) des Kurvenab-
brachten Verbindungsplatte und die Verbind- schnitts (13) hinaus.
ungsöffnungen (7) am Dokument-Finisher Falls die Höhen nicht korrekt sind, müssen Sie sie wie folgend einstellen.
den nachstehenden Vorgaben entsprechen.
Regolazione dell'altezza Conformità: Il diametro (a) del perno (8) è compreso nella gamma di altezza (b) della sezione curvata
1.Controllare che le rispettive altezze dei perni (13).
(8) sulla piastra di connessione installata Non conformità: Il diametro (a) del perno (8) si estende oltre la gamma di altezza (b) della sezione
sull'MFP e i fori di connessione (7) sulla fini- curvata (13).
trice di documenti corrispondano ai riferi- Se le altezze sono non corrispondenti, utilizzare la procedura riportata sotto per regolare l'altezza.
menti mostrati sotto.
高度调节符合：销钉 (8) 的直径 a 在弯曲部 (13) 的高度 b 的范围内。

1.确认 MFP 主机上安装的连接板的销钉 (8) 和不符合：销钉 (8) 的直径 a 超出了弯曲部 (13) 的高度 b 的范围。
装订器的连接用孔 (7) 的高度是否符合以下不符合时，通过以下步骤进行调节。
标准。
높이조정 적 합 ：핀 (8) 의 직경 a 가 곡선부 (13) 의 높이 b 의 범위에 들어간다 .

1.MFP 본체에 장착한 연결판 핀 (8) 과 문서 피 부적합：핀 (8) 의 직경 a 가 곡선부 (13) 의 높이 b 의 범위를 넘는다 .
니셔의 연결용 구멍 (7) 의 높이가 이하의 기 부적합의 경우에는 이하의 순서대로 조정합니다 .
준에 적합한지 확인합니다 .
高さ調整適　合：ピン (8) の直径 a が曲げ部 (13) の高さ b の範囲に収まっている。

1.MFP 本体に取り付けた連結板のピン (8) と不適合：ピン (8) の直径 a が曲げ部 (13) の高さ b の範囲からはみだしている。
ドキュメントフィニッシャーの連結用の穴不適合の場合は、以下の手順で調整する。
(7) の高さが以下の基準に適合するか確認
する。
7
19
16
15
14 18
17
2.Remove each of the screws (14) and 3.Remove the screw (17) to remove the span-
remove the front foot cover (15) and rear ner (18).
foot cover (16). 4.Loosen the 2 screws (19) on the front right
and on the rear right of the document fin-
isher.
2.Déposer toutes les vis (14) puis le couvercle 3.Déposer la vis (17) pour libérer la clé (18).
du pied avant (15) et le couvercle du pied 4.Desserrer les 2 vis (19) du côté avant droit et
arrière (16). arrière droit du retoucheur de document.
2.Quite cada uno de los tornillos (14) y quite la 3.Quite el tornillo (17) para extraer la llave
cubierta de la pata frontal (15) y la cubierta inglesa (18).
de la pata posterior (16). 4.Afloje los 2 tornillos (19) en los lados dere-
cho frontal y derecho posterior del finaliza-
dor de documentos.
2.Entfernen Sie sämtliche Schrauben (14) und 3.Entfernen Sie die Schraube (17), um den
nehmen Sie die Vorderfußabdeckung (15) Schlüssel (18) abzunehmen
und die Hinterfußabdeckung (16). 4.Lösen Sie die 2 Schrauben (19) vorne rechts
und hinten rechts am Dokument-Finisher.
2.Rimuovere ciascuna delle viti (14) e quindi 3.Rimuovere la vite (17) per rimuovere la chi-
rimuovere la copertura del piede anteriore ave (18).
(15) e la copertura del piede posteriore (16). 4.Allentare le 2 viti (19) sulla parte anteriore
destra e posteriore destra della finitrice di
documenti.
2.拆除各 1 颗螺丝 (14)，取下前脚座盖板 3.取下螺丝（17）以便拆下扳手（18）。

(15)、后脚座盖板 (16)。 4.拧松装订器右前侧与右后侧的各 2 颗螺丝
(19)。
2.나사 (14) 각 1 개를 빼고 풋커버 앞 (15), 풋 3.나사 (17) 1 개를 빼고 , 스패너 (18) 를 떼어

커버 뒤 (16) 를 뺍니다 . 냅니다 .
4.문서 피니셔 우측 앞과 뒤의 나사 (19) 각 2
개를 느슨하게 합니다 .
2.ビス (14) 各 1 本を外し、フットカバー前 3.ビス (17)1 本を外し、スパナー(18) を取り

(15)、
フットカバー後 (16) を取り外す。外す。
4.ドキュメントフィニッシャー右前と右後の
ビス (19) 各 2 本を緩める。
8
20
21
22
18
5.Turn the adjustment bolts (20) with the spanner (18) to adjust the height of the document finisher. 7.If the distances between the document fin-
Turning the adjustment bolt clockwise lifts the document finisher, and turning it counterclockwise isher and the MFP (21, 22) are unequal, use
lowers the document finisher. the procedure below to adjust the spacing.
6.Retighten each of the 2 screws (19) and replace the spanner (18).
5.Faire tourner les boulons de réglage (20) avec la clé (18) pour ajuster la hauteur du retoucheur 7.Si la distance entre le retoucheur de docu-
de document. ment et le MFP (21, 22) n'est pas uniforme,
Tourner le boulon de réglage dans le sens horloger pour lever le retoucheur de document, et régler en procédant de la manière suivante.
dans le sens contraire au sens horloger pour le descendre.
6.Resserrer les 2 vis (19) et repositionner la clé (18) au même endroit.
5.Gire los pernos de ajuste (20) con la llave inglesa (18) para ajustar la altura del finalizador de 7.Si las distancias entre el finalizador de docu-
documentos. mentos y la MFP (21, 22) no son iguales, uti-
Al girar el perno de ajuste en la dirección de las manecillas del reloj se levanta el finalizador de lice el siguiente procedimiento para ajustar
documentos y al girar en sentido contrario a las manecillas del reloj baja el finalizador de docu- la separación.
mentos.
6.Vuelva a apretar los 2 tornillos (19) y coloque la llave inglesa en su lugar (18).
5.Drehen Sie die Einstellschrauben (20) mit dem Schlüssel (18), um die Höhe des Dokument-Fin- 7.Falls die Abstände zwischen dem Doku-
ishers einzustellen. ment-Finisher und dem MFP (21, 22) nicht
Durch Drehen der Einstellschraube im Uhrzeigersinn wird der Dokument-Finisher angehoben, gleich sind, korrigieren Sie sie wie folgend.
während er durch Drehen entgegen dem Uhrzeigersinn abgesenkt wird.
6.Ziehen Sie die 2 Schrauben (19) wieder an und verstauen Sie den Schlüssel (18) wieder.
5.Ruotare i bulloni di regolazione (20) con la chiave (18) per regolare l'altezza della finitrice di doc- 7.Se le distanze tra la finitrice di documenti e
umenti. l'MFP (21, 22) sono disuguali, utilizzare la
Ruotando il bullone di regolazione in senso orario si solleva la finitrice di documenti, mentre procedura riportata sotto per regolare la spa-
ruotandolo in senso antiorario si abbassa la finitrice di documenti. ziatura.
6.Ristringere ciascuna delle 2 viti (19) e riporre la chiave (18).
5.使用扳手 (18) 旋转调节螺栓 (20)，以调节装订器的高度。 7.装订器与 MFP 主机的间隙（21、22）不等时，

将调节螺栓向顺时针方向旋转，装订器的高度升高，逆时针方向旋转则装订器的高度降低。按以下步骤进行调节。
6.拧紧各 2 颗螺丝 (19)，按原样安装扳手 (18)。
5.스패너 (18) 로 조정 볼트 (20) 를 돌려 문서 피니셔의 높이를 조정한다 . 7.문서 피니셔와 MFP 본체의 간격（21、22）이
조정 볼트를 시계방향으로 돌리면 문서 피니셔의 높이가 높아지고 , 반 시계방향으로 돌리면 낮아 집 같지 않은 경우에는 이하의 순서대로 조정을
니다 . 합니다 .
6.나사 (19) 각 2 개를 조이고 스패너 (18) 를 원래 자리에 장착합니다 .
5.スパナー(18) で調整ボルト (20) を回し、

ドキュメントフィニッシャーの高さを調整する。 7.ドキュメントフィニッシャーと MFP 本体の
調整ボルトを時計方向に回すとドキュメントフィニッシャーの高さが高くなり、反時計方向に回間隔（21、
22）
が等しくない場合は、以下の手
すと低くなる。順で調整を行う。
6.ビス (19) 各 2 本を締め付け、
スパナー(18) を元通り取り付ける。
9
23
24
8.Loosen the 2 screws (23) on the front left 9.Turn the adjustment bolts (24) with a Philips-head screwdriver to adjust the height of the docu-
and on the rear left of the document finisher. ment finisher.
Turning the adjustment bolt clockwise lifts the document finisher, and turning it counterclockwise
lowers the document finisher.
10.Retighten each of the 2 screws (23).
11.Replace the front foot cover (15) and rear foot cover (16).
8.Desserrer les 2 vis (23) du côté avant 9.Faire tourner les boulons de réglage (24) à l'aide d'un tournevis cruciforme pour ajuster la hau-
gauche et arrière gauche du retoucheur de teur du retoucheur de document.
document. Tourner le boulon de réglage dans le sens horloger pour lever le retoucheur de document, et
dans le sens contraire au sens horloger pour le descendre.
10.Resserrer les 2 vis (23).
11.Reposer le couvercle du pied avant (15) et le couvercle du pied arrière (16).
8.Afloje los 2 tornillos (23) en los lados izqui- 9.Gire los pernos de ajuste (24) con un destornillador de cabeza Philips para ajustar la altura del
erdo frontal e izquierdo posterior del finaliza- finalizador de documentos.
dor de documentos. Al girar el perno de ajuste en la dirección de las manecillas del reloj se levanta el finalizador de
documentos y al girar en sentido contrario a las manecillas del reloj baja el finalizador de docu-
mentos.
10.Vuelva a apretar los 2 tornillos (23).
11.Vuelva a colocar la cubierta de la pata frontal (15) y la cubierta de la pata posterior (16).
8.Lösen Sie die 2 Schrauben (23) vorne links 9.Stellen Sie die Einstellschrauben (24) mit einem Kreuzschlitzschraubendreher ein, um die Höhe
und hinten links am Dokument-Finisher. des Dokument-Finishers zu korrigieren.
Durch Drehen der Einstellschraube im Uhrzeigersinn wird der Dokument-Finisher angehoben,
während er durch Drehen entgegen dem Uhrzeigersinn abgesenkt wird.
10.Ziehen Sie die 2 Schrauben (23) nach.
11.Setzen Sie die Vorderfußabdeckung (15) und die Hinterfußabdeckung (16) wieder ein.
8.Allentare le 2 viti (23) sulla parte anteriore 9.Ruotare i bulloni di regolazione (24) con un cacciavite con testa a croce tipo Philips per regolare
sinistra e posteriore sinistra della finitrice di l'altezza della finitrice di documenti.
documenti. Ruotando il bullone di regolazione in senso orario si solleva la finitrice di documenti, mentre
ruotandolo in senso antiorario si abbassa la finitrice di documenti.
10.Ristringere ciascuna delle 2 viti (23).
11.Ricollocare la copertura del piede anteriore (15) e la copertura del piede posteriore (16).
8.拧松装订器左前侧与左后侧的各 2 颗螺丝 9.使用十字螺丝刀旋转调节螺栓 (24)，以调节装订器的高度。

(23)。将调节螺栓向顺时针方向旋转，装订器的高度升高，逆时针方向旋转则装订器的高度降低。
10.拧紧各 2 颗螺丝 (23)。
11.将前脚座盖板 (15)、后脚座盖板 (16) 按原样安装
8.문서 피니셔 좌측 앞과 뒤의 나사 (23) 각 2 9.플러스 드라이버로 조정 볼트 (24) 를 돌려 문서 피니셔 높이를 조정합니다 .

개를 느슨하게 합니다 . 조정 볼트를 시계방향으로 돌리면 문서 피니셔의 높이가 높아지고 , 반 시계방향으로 돌리면 낮아 집
니다 .
10. 나사 (23) 각 2 개를 조입니다 .
11. 풋커버 앞 (15), 풋커버 뒤 (16) 를 원래대로 장착합니다 .
8.ドキュメントフィニッシャー左前と左後の 9.プラスドライバーで調整ボルト (24) を回し、ドキュメントフィニッシャーの高さを調整する。

ビス (23) 各 2 本を緩める。調整ボルトを時計方向に回すとドキュメントフィニッシャーの高さが高くなり、反時計方向に回
すと低くなる。
10.ビス (23) 各 2 本を締め付ける。
11.フットカバー前 (15)、フットカバー後 (16) を元通りに取り付ける。
10
78.5mm±2.5
158mm±2.5
Adjusting the stapling position

1.Connect the MFP power plug to the wall outlet and turn the MFP main power switch on.
2.Make a test copy using staple mode (double stapled).
3.Check whether the stapling position is off-center. If the staple position is off-center, follow the procedure below to adjust the position.
<Reference value> 78.5 mm ±2.5 mm from the center of the paper
Réglage de la position d'agrafage

1.Insérer la fiche d’alimentation du MFP dans la prise murale et mettre l’interrupteur principal du MFP sous tension.
2.Procéder à une copie d'essai en mode agrafage (double agrafage).
3.Vérifier que la position d'agrafage n'est pas en décalage.
Si la position d'agrafage est décalée, la régler en procédant de la manière suivante.
<Valeur de référence> 78,5 mm ±2,5 mm depuis le milieu de la feuille de papier.
Ajuste de la posición de grapado

1.Conecte el enchufe del MFP en el receptáculo de pared y encienda el interruptor principal del MFP.
2.Haga una copia de prueba en el modo de grapado (grapado doble).
3.Compruebe si la posición de grapado está descentrada.
Si la posición de grapado está descentrada, realice el siguiente procedimiento para ajustar la posición.
<Valor de referencia> 78,5 mm ± 2,5 mm del centro del papel
Einstellen der Heftposition

1.Stecken Sie den Netzstecker des MFP in die Wandsteckdose und schalten Sie den MFP am Hauptschalter ein.
2.Erstellen Sie eine Probekopie im Heftmodus (doppelt geheftet).
3.Prüfen Sie, ob die Heftposition außermittig ist.
Falls die Heftposition außermittig ist, müssen Sie sie wie folgend einstellen.
<Bezugswert> 78,5 mm ±2,5 mm von der Blattmitte
Regolazione della posizione di spillatura

1.Collegare la spina del cavo di alimentazione dell’MFP alla presa a muro della rete elettrica e accendere l’interruttore principale di alimentazione.
2.Eseguire una copia di prova utilizzando la modalità di spillatura con punti metallici (spillatura doppia).
3.Verificare che la posizione di spillatura non sia fuori centro.
Se la posizione di spillatura è fuori centro, seguire la procedura riportata sotto per regolare la posizione.
<Valore di riferimento> 78,5 mm ± 2,5 mm dal centro del foglio
调节装订位置
1.将 MFP 主机上的电源插头插入电源插座中，打开主电源开关。
2.在装订模式（2 点固定）下进行测试复印。
3.确认装订位置的中心偏差。装订位置偏离中心时，按以下步骤进行调节。
＜基准值＞距离纸张中心 78.5mm± 2.5mm
스테이플 위치 조정
1.MFP 본체 전원플러그를 콘센트에 꽂고 주 전원 스위치를 ON 으로 합니다 .
2.스테이플 모드 （2 곳）
에서 시험복사를 합니다 .
3.스테이플 위치의 센터 어긋남을 확인합니다 . 스테이플 위치가 중심에서 벗어난 경우다음 순서로 조정을 합니다 .
＜기준치＞ 용지 센터에서 78.5mm± 2.5mm
ステープル位置の調整
1.MFP 本体の電源プラグをコンセントに差し込み、主電源スイッチを ON にする。
2.ステープルモード（2 箇所止め）でテストコピーを行う。
3.ステープル位置のセンターずれを確認する。ステープル位置が中心からずれていた場合、次の手順で調整を行う。
＜基準値＞用紙センターより 78.5mm± 2.5mm
11
(a) (b)
4.Set maintenance mode U246, select Finisher and Staple HP. 7.Repeat steps 4 to 6 until the staple position is within the reference
5.Adjust the values. value.
If the paper is stapled too close to the front of the machine (a): Increase <Reference value> 78.5 mm ±2.5 mm from the center of the paper
the setting value.
If the paper is stapled too close to the rear of the machine (b):
Decrease the setting value.
6.Perform a test copy.
4.Passer en mode maintenance U246, sélectionner Finisher et Staple 6.Effectuer une copie de test.
HP. 7.Recommencer les étapes 4 à 6 jusqu'à ce que la position d'agrafe soit
5.Régler les valeurs. conforme à la valeur de référence
Si le papier est agrafé trop près de l'avant de la machine (a): aug- <Valeur de référence> 78,5 mm ±2,5 mm depuis le milieu de la feuille
menter la valeur de réglage. de papier.
Si le papier est agrafé trop près de l'arrière de la machine (b): réduire
la valeur de réglage.
4.Entre en el modo de mantenimiento U246, seleccione Finisher y Staple 6.Haga una copia de prueba.
HP. 7.Repita los pasos 4 a 6 hasta que la posición de grapado se encuentre
5.Ajuste los valores. dentro del valor de referencia.
Si el grapado del papel se encuentra demasiado cerca del frente de la <Valor de referencia> 78,5 mm ± 2,5 mm del centro del pape
máquina (a): aumente el valor de configuración.
Si el grapado del papel se encuentra demasiado cerca de la parte pos-
terior de la máquina (b): disminuya el valor de configuración.
4.Schalten Sie in den Wartungsmodus U246, wählen Sie Finisher und 6.Eine Testkopie erstellen.
Staple HP. 7.Wiederholen Sie die Schritte 4 bis 6, bis die Heftposition im Bereich
5.Die Werte einstellen. des Bezugswerts liegt.
Falls das Papier zu nahe am vorderen Rand des Geräts (a) abgesta- <Bezugswert> 78,5 mm ±2,5 mm von der Blattmitte
pelt wird: Vergrößern Sie den Stellwert.
Falls das Papier zu nahe am hinteren Rand des Geräts (b) abgestapelt
wird: Verkleinern Sie den Stellwert.
4.Impostare la modalità manutenzione U246, selezionare Finisher e Sta- 6.Eseguire una copia di prova.
ple HP. 7.Ripetere i passi 4 to 6 finché la posizione di spillatura risulta all'interno
5.Regolare i valori. del valore di riferimento.
Se il foglio viene spillato troppo vicino alla parte anteriore della mac- <Valore di riferimento> 78,5 mm ± 2,5 mm dal centro del foglio
china (a): Aumentare il valore di impostazione.
Se il foglio viene spillato troppo vicino alla parte posteriore della mac-
china (b): Diminuire il valore di impostazione.
4.设置维护模式 U246，选择 Finisher、Staple HP。 7.重复步骤 4 ～ 6，直到装订位置在基准范围内为止。

5.调整设定值。＜基准值＞距离纸张中心 78.5mm± 2.5mm
装订位置向机器前部偏移时 (a)：调高设定值。
装订位置向机器后部偏移时 (b)：调低设定值。
4.메인터넌스 모드 U246 을 세트하고 Finisher, Staple HP 를 선택합니 7.스테이플 위치가 기준치내가 될 때까지 순서 4 ～ 6 을 반복합니다 .
다. ＜기준치＞ 용지 센터에서 78.5mm± 2.5mm
스테이플 위치가 기기앞측으로 벗어난 경우 (a)：설정치를 높입니다 .
스테이플 위치가 기기뒷측으로 벗어난 경우 (b)：설정치를 내입니다 .
4.メンテナンスモード U246 をセットし、Finisher、

Staple HP を選択す 7.ステープル位置が基準値内になるまで、手順 4 ～ 6 を繰り返す。
る。＜基準値＞用紙センターより 78.5mm± 2.5mm
ステープル位置が機械前側にずれている場合 (a)：設定値を上げる。
ステープル位置が機械後側にずれている場合 (b)：設定値を下げる。
12
ATTACHMENT KIT
E
G
B D
F
A
C I
J
H
K
E. Rear left stay.............................................. 1

English
F. Left scanner cover ..................................... 1
Supplied parts G. Front left stay ............................................. 1
A. Drive unit ................................................... 1 H. Eject unit .................................................... 1
B. Paper entry unit ......................................... 1 I. Wire stopper .............................................. 1
C. Paper entry unit cover ............................... 1 J. Upper front cover ....................................... 1
D. Edging ....................................................... 1 K. Left connection cover................................. 1
E. Support arrière gauche .............................. 1

Français
F. Couvercle de scanner gauche ................... 1
Pièces fournies G. Support avant gauche................................ 1
A. Unité d'entraînement ................................. 1 H. Unité d'éjection .......................................... 1
B. Unité d'entrée du papier ............................ 1 I. Butée de cable........................................... 1
C. Couvercle de l'unité d'entrée du papier ..... 1 J. Couvercle avant supérieur......................... 1
D. Passage..................................................... 1 K. Couvercle de connexion gauche ............... 1
E. Soporte izquierdo trasero .......................... 1

Español
F. Cubierta izquierda del escáner .................. 1
Partes suministradas G. Soporte frontal izquierdo............................ 1
A. Unidad de accionamiento .......................... 1 H. Unidad de salida ........................................ 1
B. Unidad de ingreso de papel....................... 1 I. Tope para cables ....................................... 1
C. Cubierta de la unidad de ingreso de papel ... 1 J. Cubierta frontal superior ............................ 1
D. Pestaña ..................................................... 1 K. Cubierta de conexiones izquierda ............. 1
E. Hintere linke Stütze.................................... 1

Deutsch
F. Linke Scanner-Abdeckung......................... 1
Gelieferte Teile G. Vordere linke Stütze................................... 1
A. Antriebseinheit........................................... 1 H. Auswerfeinheit ........................................... 1
B. Papiereinzugseinheit ................................. 1 I. Kabelhalter................................................. 1
C. Abdeckung der Papiereinzugseinheit ........ 1 J. Obere vordere Abdeckung......................... 1
D. Kantenschutz............................................. 1 K. Linke Verbindungsabdeckung.................... 1
E. Supporto posteriore sinistro....................... 1

Italiano
F. Coperchio sinistro dello scanner................ 1
Parti di fornitura G. Supporto anteriore sinistro......................... 1
A. Unità guida ................................................ 1 H. Unità di espulsione .................................... 1
B. Unità di ingresso carta ............................... 1 I. Fermacavo................................................. 1
C. Coperchio unità di ingresso carta .............. 1 J. Coperchio superiore anterior ..................... 1
D. Bordo ......................................................... 1 K. Coperchio connessione sinistro................. 1
简体中文 E. 左后部支架 ...........................1

F. 扫描仪左盖板 .........................1
附属品 G. 左前部支架 ...........................1
A. 驱动单元............................. 1 H. 排纸单元 .............................1
B. 进纸单元............................. 1 I. 电线固定夹 ...........................1
C. 进纸单元盖板......................... 1 J. 前上部盖板 ...........................1
D. 电线护具............................. 1 K. 连接左盖板 ...........................1
한국어 E. 좌측 뒷 받침대.................................... 1
F. 스캐너 좌측 커버................................. 1
동봉품 G. 좌측 앞 받침대.................................... 1
A. 구동 유니트........................................ 1 H. 배출 유니트........................................ 1
B. 반입 유니트........................................ 1 I. 와이어 스토퍼..................................... 1
C. 반입 유니트 커버................................. 1 J. 전면 상커버........................................ 1
D. 에징.................................................. 1 K. 연결 좌측커버..................................... 1
日本語 E. 左後ステー ...........................1

F. スキャナー左カバー ...................1
同梱品 G. 左前ステー ...........................1
A. 駆動ユニット......................... 1 H. 排出ユニット .........................1
B. 搬入ユニット......................... 1 I. ワイヤーストッパー ...................1
C. 搬入ユニットカバー................... 1 J. 前上カバー ...........................1
D. エッジング........................... 1 K. 連結左カバー .........................1
1
O P Q
L
N R
L. Left cover ................................................... 1 Be sure to remove any tape and/or cushioning Before installing the AK-730, make sure that the
M. Upper left cover ......................................... 1 material from supplied parts. MFP’s main power switch is turned off and that
N. Paper conveying unit ................................. 1 its power cord is unplugged from the power out-
O. M4 × 8 screw ............................................. 7 let.
P. M4 × 20 screw ........................................... 4
Q. P Tite screw M3 × 8 ................................... 1
R. Lower connection cover............................. 1
L. Couvercle gauche...................................... 1 Veillez à retirer les morceaux de bande adhé- Avant d’installer l'AK-730, s’assurer que l’inter-
M. Couvercle supérieur gauche...................... 1 sive et/ou les matériaux de rembourrage des rupteur d’alimentation principal du MFP est
N. Unité de transport du papier ...................... 1 pièces fournies. coupé et que le cordon d’alimentation est
O. Vis M4 × 8.................................................. 7 débranché de la prise secteur.
P. Vis M4 × 20................................................ 4
Q. Vis P Tite M3 × 8 ....................................... 1
R. Couvercle de connexion inférieur .............. 1
L. Cubierta izquierda...................................... 1 Asegúrese de despegar todas las cintas y/o Antes de instalar el AK-730, asegúrese de que
M. Cubierta superior izquierda........................ 1 material amortiguador de las partes suministra- el interruptor principal de la alimentación de la
N. Unidad de transporte de papel .................. 1 das. MFP esté desconectado y que su cable de ali-
O. Tornillo M4 × 8 ........................................... 7 mentación esté desenchufado de la toma de
P. Tornillo M4 × 20 ......................................... 4 corriente.
Q. Tornillo P Tite M3 × 8 ................................. 1
R. Cubierta de conexiones inferior ................. 1
L. Linke Abdeckung ....................................... 1 Entfernen Sie Klebeband und/oder Dämpfungs- Vor dem Einbau des AK-730 muss der MFP-
M. Obere linke Abdeckung ............................. 1 material vollständig von den mitgelieferten Hauptschalter ausgeschaltet und das Netzkabel
N. Papierfördereinheit .................................... 1 Teilen. von der Steckdose abgezogen sein.
O. M4 × 8 Schraube ....................................... 7
P. M4 × 20 Schraube ..................................... 4
Q. P-Tite-Schraube M3 × 8 ............................ 1
R. Untere Verbindungsabdeckung ................. 1
L. Coperchio sinistro...................................... 1 Accertarsi di rimuovere tutti i nastri adesivi e/o il Prima di installare l'unità AK-730, assicurarsi
M. Coperchio superiore sinistro...................... 1 materiale di imbottitura dalle parti fornite. che l’interruttore principale dell'MFP sia spento
N. Unità di trasporto carta .............................. 1 e che il suo cavo di alimentazione sia scollegato
O. Vite M4 × 8 ................................................ 7 presa di corrente.
P. Vite M4 × 20 .............................................. 4
Q. Vite P Tite M3 × 8 ...................................... 1
R. Coperchio connessione inferior ................. 1
L. 左盖板............................... 1 如果附属品上带有固定胶带，缓冲材料时务必揭安装 AK-730 时，请务必将 MFP 主机电源关闭，关

M. 左上部盖板........................... 1 下。拔下电源插头再进行安装作业。
N. 输纸单元............................. 1
O. M4×8 螺丝 ........................... 7
P. M4×20 螺丝 .......................... 4
Q. 紧固型 P 螺丝 M3×8 ................... 1
R. 连接下盖板........................... 1
L. 좌측 커버........................................... 1 동봉품에 고정 테이프 , 완충재가 붙어 있는 경 AK-730 을 부착할 때에는 반드시 MFP 본체의
M. 좌측 상커버........................................ 1 우에는 반드시 제거할 것 . 주 전원 스위치를 OFF 로 하고 전원 플러그를
N. 반송 유니트........................................ 1 제거하고 작업을 할 것 .
O. 나사 M4×8......................................... 7
P. 나사 M4×20 ....................................... 4
Q. 나사 M3×8P Tight............................... 1
R. 연결 하커버........................................ 1
L. 左カバー............................. 1 同梱品に固定テープ、緩衝材がついている場合 AK-730 を取り付ける際は、必ず MFP 本体の主電

M. 左上カバー........................... 1 は、
必ず取り外すこと。源スイッチを OFF にし、電源プラグを外して作
N. 搬送ユニット......................... 1 業をおこなうこと。
O. ビス M4×8 ........................... 7
P. ビス M4×20 .......................... 4
Q. ビス M3×8P タイト.................... 1
R. 連結下カバー......................... 1
2
3
6
2
1
3
4
5
Procedure 2.Push in the top and bottom hooks (3) and 3.Remove the 2 screws (5) inside the interface
1.Remove the 2 screws (2) in the left ISU open the interface cover (4). cover (4) and remove the left scanner cover
cover (1). (6).
Procédure 2.Appuyer sur les crochets haut et bas (3) et 3.Déposer les 2 vis (5) à l'intérieur du couver-
1.Déposer les 2 vis (2) du couvercle gauche ouvrir le couvercle de l'interface (4). cle de l'interface (4) et déposer le couvercle
de l'ISU (1). de scanner gauche (6).
Procedimiento 2.Presione los ganchos superior e inferior (3) y 3.Quite los 2 tornillos (5) de interior de la cubi-
1.Quite los 2 tornillos (2) de la cubierta ISU abra la cubierta de la interfaz (4). erta de la interfaz (4) y quite la cubierta
izquierda (1). izquierda del escáner (6).
Verfahren 2.Drücken Sie die Haken (3) oben und unten 3.Entfernen Sie die 2 Schrauben (5) im Innern
1.Entfernen Sie die 2 Schrauben (2) in der ein und öffnen Sie die Schnittstellenabdeck- der Schnittstellenabdeckung (4) und
linken ISU-Abdeckung (1). ung (4). nehmen Sie die linke Scanner-Abdeckung
(6) ab.
Procedura 2.Spingere i ganci (3) superiore e inferiore ed 3.Rimuovere le 2 viti (5) all'interno della coper-
1.Rimuovere le 2 viti (2) sul coperchio ISU sin- aprire la copertura di interfaccia (4). tura di interfaccia (4) e quindi rimuovere il
istro (1). coperchio sinistro dello scanner (6).
安装步骤 2.按压上下的卡扣 (3) 以打开接口盖板 (4)。 3.卸下接口盖板 (4) 内侧的 2 颗螺丝 (5)，拆下
1.卸下 ISU 左盖板 (1) 的 2 颗螺丝 (2)。扫描仪左盖板 (6)。
설치순서 2.상하의 후크 (3) 를 눌러 인터페이스 커버 (4) 3.인터페이스 커버 (4) 안쪽의 나사 (5) 2 개를

1.ISU 좌측 커버 (1) 의 나사 (2) 2 개를 제거합 를 엽니다 . 제거하고 스캐너 좌측커버 (6) 를 제거합니
니다 . 다.
取付手順 2.上下のフック (3) を押してインターフェイ 3.インターフェイスカバー(4) 内側のビス

1.ISU 左カバー(1) のビス (2)2 本を取り外す。スカバー(4) を開く。 (5)2 本を外し、スキャナー左カバー(6) を取
り外す。
3
13
15
9
14
12
10
11
8
4.Open the front cover (7) on the MFP. 7.Remove the screw (11) from the fan cover 9.Remove the eject cover (15).
5.Pull out the paper conveyor cover (8). (10). * Pull the lower front side to the left before
6.If the operation panel (9) is lowered, raise it 8.Remove the screw (12) and pull the upper removing the cover.
to the top position. right cover (13) outwards slightly while
removing the front right cover (14).
4.Ouvrir le capot avant (7) sur le MFP. 7.Déposer la vis (11) du couvercle du ventila- 9.Déposer le capot d’éjection (15).
5.Sortir le couvercle du transporteur du papier teur (10). * Tirer le côté avant inférieur sur la gauche
(8). 8.Déposer la vis (12) et tirer légèrement le avant de déposer le capot.
6.Si le panneau de commande (9) est abaissé, couvercle supérieur droit (13) vers l'extérieur
le relever dans sa position maximum. tout en déposant le couvercle avant droit
(14).
4.Abra la cubierta frontal (7) en la MFP. 7.Quite el tornillo (11) de la cubierta del venti- 9.Quite la cubierta de expulsión (15).
5.Extraiga la cubierta de la unidad de trans- lador (10). * Tire del lado frontal inferior hacia la izqui-
porte de papel (8). 8.Quite el tornillo (12) y saque la cubierta erda antes de quitar la cubierta.
6.Si el panel de trabajo (9) está bajo, levántelo superior derecha (13) ligeramente mientras
hasta la posición superior. quita la cubierta frontal derecha (14).
4.Öffnen Sie die vordere Abdeckung (7) am 7.Entfernen Sie die Schraube (11) von der 9.Entfernen Sie die Auswerfabdeckung (15).
MFP. Lüfterabdeckung (10). * Ziehen Sie die untere Vorderseite nach
5.Ziehen Sie die Papierfördererabdeckung (8) 8.Entfernen Sie die Schraube (12) und ziehen links, bevor Sie die Abdeckung abnehmen.
heraus. Sie die obere rechte Abdeckung (13) leicht
6.Heben Sie das Bedienfeld (9) in die oberste nach außen, während Sie gleichzeitig die
Position, falls es gesenkt ist. vordere rechte Abdeckung (14) abnehmen.
4.Aprire il pannello anteriore (7) sull'MFP. 7.Rimuovere la vite (11) dal coperchio ventola 9.Rimuovere il coperchio di espulsione carta
5.Estrarre il coperchio di trasporto carta (8). (10). (15).
6.Se il pannello operativo (9) è abbassato, sol- 8.Rimuovere la vite (12) e tirare il coperchio * Tirare il lato anteriore in basso a sinistra
levarlo alla posizione in alto. superiore destro (13) leggermente verso prima di rimuovere il coperchio.
l'esterno mentre si rimuove il coperchio ante-
riore destro (14).
4.打开 MFP 主机的前盖板 (7)。 7.卸下风扇盖板 (10) 的 1 颗螺丝 (11)。 9.拆下排纸盖板 (15)。
5.拉出输纸盖板 (8)。 8.卸下 1 颗螺丝 (12)，稍稍拉出右上部盖板 ※ 将盖板前下部向左侧拉出以拆卸。
6.操作面板 (9) 处于低位时，将其升到最高位 (13) 的同时，拆下右前部盖板 (14)。
置。
4.MFP 본체의 전면커버 (7) 를 엽니다 . 7.팬커버 (10) 의 나사 (11) 1 개를 제거합니다 . 9.배출커버 (15) 를 제거합니다 .
5.반송커버 (8) 를 당겨 냅니다 . 8.나사 (12) 1 개를 제거하고 오른쪽 상커버 ※ 전면 아래쪽을 좌측으로 당겨서 제거합니
6.조작판넬 (9) 이 내려가 있는 경우에는 위로 (13) 를 조금 당기면서 오른쪽 전면커버 (14) 　 다.
올립니다 . 를 제거합니다 .
4.MFP 本体の前カバー(7) を開く。 7.ファンカバー(10) のビス (11)1 本を外す。 9.排出カバー(15) を取り外す。

5.搬送カバー(8) を引き出す。 8.ビス (12)1 本を外し、右上カバー(13) を少 ※ 前下側を左側に引いてから取り外す。
6.操作パネル (9) が下がっている場合は上位し外に引っ張りながら右前カバー(14) を取
置に上げる。り外す。
4
19
17
21 A
16
18
22 20 16
10.Remove the 2 M4 × 10 screws (16) and 11.Insert the hook (19) on the upper side of the drive unit (A) and the projection (20) on the under-
remove the rear tray cover (17) and scanner side into the respective positioning holes (21) (22) in the back plate and secure the drive unit
bottom cover (18). using the 2 M4 × 10 screws (16) removed in step 10.
10.Déposer les 2 vis M4 × 10 (16) et déposer le 11.Insérer le crochet (19) sur le côté supérieur de l'unité d'entraînement (A) et la projection (20)
couvercle du support arrière (17) et le cou- inférieure dans les trous de positionnement correspondant (21) (22) de la tôle arrière et fixer
vercle inférieur du scanner (18). l'unité d'entraînement à l'aide des 2 vis M4 × 10 (16) déposées à l'étape 10.
10.Quite los 2 tornillos M4 × 10 (16) y quite la 11.Inserte el gancho (19) del lado superior de la unidad de accionamiento (A) y el saliente (20) del
cubierta izquierda de la bandeja (17) y la lado inferior en sus respectivos orificios de posición (21) (22) en la placa posterior y asegure la
cubierta inferior del escáner (18). unidad de accionamiento usando los 2 tornillos M4 × 10 (16) quitados en el paso 10.
10.Entfernen Sie die 2 M4 × 10 Schrauben (16) 11.Setzen Sie den Haken (19) an der Oberseite der Antriebseinheit (A) und den Vorsprung (20) an
und nehmen Sie die hintere Fachabdeckung der Unterseite in die entsprechenden Positionierungsöffnungen (21) (22) der Rückplatte ein und
(17) und die Scanner-Bodenabdeckung (18) sichern Sie die Antriebseinheit mit den 2 in Schritt 10 entfernten M4 × 10 Schrauben (16).
ab.
10.Rimuovere le 2 viti M4 × 10 (16) e quindi 11.Inserire il gancio (19) sul lato superiore dell'unità guida (A) e la parte sporgente (20) sulla parte
rimuovere il coperchio posteriore del vassoio inferiore, nei rispettivi fori di posizionamento (21) (22) nella piastra posteriore e fissare l'unità
(17) e il coperchio in basso dello scanner guida usando le 2 viti M4 × 10 (16) rimosse nel punto 10.
(18).
10.卸下 2 颗 M4×10(16) 螺丝，拆下托盘后部盖 11.将驱动单元 (A) 上部的卡扣 (19) 和下部的突出部 (20) 分别插入背板的定位孔 (21)(22) 中，使用
板 (17) 以及扫描仪底部盖板 (18)。步骤 10 中卸下的 2 颗螺丝 M4×10(16) 进行固定。
10.나사 M4×10(16) 2 개를 제거하고 트레이 뒷 11.구동 유니트 (A) 윗쪽 후크 (19) 및 아래쪽 돌기 (20) 를 뒷판의 위치고정 구멍 (21)(22) 에 각각
커버 (17) 및 스캐너 밑커버 (18) 를 제거합 넣고 순서 10 의 나사 M4×10(16) 2 개로 고정합니다 .
니다 .
10.ビス M4×10(16)2 本を外し、

トレイ後カバー 11.駆動ユニット (A) 上側のフック (19) および下側の突起 (20) を後板の位置決め穴 (21)(22) にそ
(17) およびスキャナー底カバー(18) を取りれぞれ入れ、
手順 10 のビス M4×10(16)2 本で固定する。
外す。
5
A 27 23
25
A
D
24
B
26
12.Insert the projection (23) on the paper entry unit (B) into the hole (24) in the drive unit (A) and 13.Attach the edging (D) to the side plate, run
insert the projection (25) into the hole (26) in the MFP frame to attach the paper entry unit (B). the cable from the drive unit (A) through the
Push the paper entry unit (B) to the right and fit the projection (25) into the hole (26) until it clicks edging (D) and secure it in place.
into place.
NOTICE
When installing the paper entry unit, take care not to dislodge the paper eject actuator (27).
After installing the unit, check the operation of the actuator.
12. Insérer la projection (23) de l'unité d'entrée du papier (B) dans le trou (24) de l'unité d'entraînement (A) 13.Fixer le passage (D) à la tôle latérale, faire
et insérer la projection (25) dans le trou (26) du bâti du MFP pour fixer l'unité d'entrée du papier (B). passer le câble venant de l'unité d'entraîne-
Pousser l'unité d'entrée du papier (B) vers la droite et insérer la projection (25) dans le trou (26) ment (A) dans le passage (D) et le fixer en
jusqu'au clic. place.
AVIS
À l'installation de l'unité d'entrée du papier, attention à ne pas déplacer l'actionneur d'éjection du papier
(27). Après avoir installé l'unité, vérifier le bon fonctionnement de l'actuateur.
12. Inserte el saliente (23) de la unidad de ingreso de papel (B) en el orificio (24) de la unidad de accionamiento (A) 13.Fije la pestaña (D) a la placa lateral, tienda
e inserte el saliente (25) en el orificio (26) de la carcasa de la MFP para fijar la unidad de ingreso de papel (B). el cable desde la unidad de accionamiento
Presione la unidad de ingreso de papel (B) hacia la derecha y encaje el saliente (25) en el orificio (26) hasta (A) a través de la pestaña (D) y asegúrelo en
escuchar un clic. posición.
AVISO
Cuando instale la unidad de ingreso de papel tenga cuidado de no desplazar el actuador de expulsión de papel
(27). Después de instalar la unidad, compruebe el funcionamiento del actuador.
12. Setzen Sie den Vorsprung (23) an der Papiereinzugseinheit (B) in die Öffnung (24) der Antriebseinheit (A) ein 13. Bringen Sie den Kantenschutz (D) an der
und setzen Sie den Vorsprung (25) in die Öffnung (26) im MFP-Rahmen ein, um die Papiereinzugseinheit (B) Seitenplatte an, führen Sie das Kabel von
anzubringen. der Antriebseinheit (A) durch den Kanten-
Drücken Sie die Papiereinzugseinheit (B) nach rechts und drücken Sie den Vorsprung (25) in die Öffnung (26),
schutz (D) und befestigen Sie es.
bis er einrastet.
HINWEIS
Achten Sie beim Anbringen der Papiereinzugseinheit darauf, dass der Papierauswerfaktuator (27) nicht
abspringt. Überprüfen Sie nach dem Montieren der Einheit die Funktionsfähigkeit des Aktuators.
12. Inserire la parte sporgente (23) sull'unità di ingresso carta (B) nel foro (24) dell'unità guida (A), ed 13.Fissare il bordo (D) alla piastra laterale, far
inserire la parte sporgente (25) nel foro (26) del telaio dell'MFP per fissare l'unità di ingresso carta (B). passare il cavo dall'unità guida (A) attra-
Spingere l'unità di ingresso carta (B) alla destra ed inserire la parte sporgente (25) nel foro (26) finché verso il bordo (D) e fissarlo in posizione.
non scatta in posizione con un clic.
NOTIFICA
Quando si installa l'unità di ingresso carta, fare attenzione a non rimuovere l'attuatore (27) di espulsione
carta. Dopo l'installazione dell'unità, controllare il funzionamento dell'attuatore.
12.将进纸单元 (B) 的突出部 (23) 插入驱动单元 (A) 的孔 (24) 中，将突出部 (25) 插入主机框架的孔 13.在侧板上安装电线护具 (D)，将来自驱动单元
(26) 中以安装进纸单元 (B)。 (A) 的电线从其中穿过以进行固定。
将进纸单元 (B) 向右侧推，直到突出部 (25) 嵌入孔 (26) 中并发出咔嚓声为止。
注意
安装进纸单元时，请勿拆卸排出执行元件 (27)。
安装后，必须进行执行元件的动作确认。
12.반입 유니트 (B) 의 돌기 (23) 를 구동 유니트 (A) 의 구멍 (24) 에 넣고 돌기 (25) 를 본체 프레임 13.측면판에 에징 (D) 을 부착 , 구동 유니트 (A)
구멍 (26) 에 넣어 반입 유니트 (B) 를 장착합니다 . 의 전선을 통과시키고 고정합니다 .
반입 유니트 (B) 를 오른쪽으로 밀고 돌기 (25) 를 구멍 (26) 에 딸깍하고 소리가 날 때까지 끼웁니다 .
주의
반입 유니트를 부착할 때에는 배출 액츄에이터 (27) 가 빠지지 않도록 작업을 합니다 .
부착 후 액츄에이터의 동작 확인을 합니다 .
12.搬入ユニット (B) の突起 (23) を駆動ユニット (A) の穴 (24) に入れ、突起 (25) を本体フレーム 13.側板にエッジング (D) を取り付け、駆動ユ
の穴 (26) に入れて搬入ユニット (B) を取り付ける。ニット (A) からの電線を通し、固定する。
搬入ユニット (B) を右側に押し、突起 (25) を穴 (26) にカチッと音がするまではめ込むこと。
注意
搬入ユニットを取り付ける時は、排出のアクチュエーター(27) を外さないように作業をする。
取付後、アクチュエーターの動作確認を行うこと。
6
A
29
28
E
29
28
31
O O
30 32
14.Insert the 2 projections (28) on the rear left 15.Insert the clamped binding band (30) 16.Insert the hook (32) on the left scanner cover
stay (E) into the holes (29) in the side plate attached to the cable from the drive unit (A) (F) into the hole in the side plate and secure
and secure the rear left stay (E) with the M4 into the hole, run the cable through the 2 the left scanner cover (F) with the M4 × 8
× 8 screw (O). edgings (31) and secure it in place. screw (O).
14.Insérer les 2 projections (28) du support arri- 15.Insérer le collier de fixation (30) fixé au câble 16.Insérer le crochet (32) du couvercle de scan-
ère gauche (E) dans les trous (29) de la tôle venant de l'unité d'entraînement (A) dans le ner gauche (F) dans le trou de la tôle latérale
latérale et fixer le support arrière gauche (E) trou, faire passer le câble dans les 2 pas- et fixer le couvercle de scanner gauche (F) à
à l'aide d'une vis M4 × 8 (O). sages (31) et le fixer en place. l'aide d'une vis M4 × 8 (O).
14.Inserte los 2 salientes (28) del soporte tra- 15.Inserte la correa de sujeción (30) fijada al 16.Inserte el gancho (32) de la cubierta izqui-
sero izquierdo (E) en los orificios (29) de la cable de la unidad de accionamiento (A) en erda del escáner (F) en el orificio de la placa
placa lateral y asegure el soporte trasero el orificio, tienda el cable a través de las 2 lateral y asegure la cubierta izquierda del
izquierdo (E) con el tornillo M4 × 8 (O). pestañas (31) y asegúrelo en posición. escáner (F) con el tornillo M4 × 8 (O).
14.Setzen Sie die 2 Vorsprünge (28) der hin- 15.Setzen Sie das Klemmschellenband (30) am 16.Setzen Sie den Haken (32) an der linken
teren linken Stütze (E) in die Öffnungen (29) Kabel von der Antriebseinheit (A) in die Öff- Scanner-Abdeckung (F) in die Öffnung der
der Seitenplatte ein und sichern Sie die hin- nung ein, führen Sie das Kabel durch die 2 Seitenplatte und sichern Sie die linke Scan-
tere linke Stütze (E) mit der M4 × 8 Kantenschutze (31) und befestigen Sie es. ner-Abdeckung (F) mit der M4 × 8 Schraube
Schraube (O). (O).
14.Inserire le 2 parti sporgenti (28) sul supporto 15.Inserire la fascetta di legatura con morsetto 16.Inserire il gancio (32) sul coperchio sinistro
posteriore sinistro (E) nei fori (29) nella pias- (30) applicata al cavo dell'unità guida (A) nel dello scanner (F) nel foro della piastra later-
tra laterale, e quindi fissare il supporto pos- foro, far passare il cavo attraverso i 2 bordi ale e fissare il coperchio sinistro dello scan-
teriore sinistro (E) con la vite M4 × 8 (O). (31) e fissarlo in posizione. ner (F) con la vite M4 × 8 (O).
14.将左后部支架 (E) 的 2 处突出部 (28) 插入侧 15.将来自驱动单元 (A) 的电线附带的带夹头束 16.将扫描仪左盖板 (F) 的卡扣 (32) 插入侧板的
板的孔 (29) 中，使用 1 颗 M4×8 螺丝 (O) 来线带 (30) 插入孔中固定，并使其从 2 处电线孔中，使用 1 颗 M4×8 螺丝 (O) 螺丝来固定
固定左后部支架 (E)。护具 (31) 中通过以固定。扫描仪左盖板 (F)。
14.좌측 뒷 받침대 (E) 의 돌기 (28) 2 개를 측면 15.구동 유니트 (A) 의 전선에 붙어 있는 클램프 16.스캐너 좌측커버 (F) 의 후크 (32) 를 측면판
판의 구멍 (29) 에 넣고 나사 M4×8(O)1 개로 부착 결속밴드 (30) 를 구멍에 넣고 고정해 2 의 구멍에 넣고 나사 M4×8(O) 1 개로 스캐
좌측 뒷 받침대 (E) 를 고정합니다 . 곳의 에징 (31) 을 통과 시켜 고정합니다 . 너 좌측커버 (F) 를 고정합니다 .
14.左後ステー(E) の 2 個の突起 (28) を側板の 15.駆動ユニット (A) からの電線に付いている 16.スキャナー左カバー(F) のフック (32) を側
穴 (29) に入れて、ビス M4×8(O)1 本で左後クランプ付き結束バンド (30) を穴に入れ固板の穴に入れて、ビス M4×8(O)1 本でスキャ
ステー(E) を固定する。定し、
2 箇所のエッジング (31) に通し、固定ナー左カバー(F) を固定する。
する。
7
33
G 33
17.Insert the 2 projections (33) on the front left

stay (G) into the holes in the left cover on the
MFP and temporarily fasten the front left
stay (G) in place with the 2 M4 × 20 screws
(P).
17.Insérer les 2 projections (33) du support

avant gauche (G) dans les trous du couver-
cle gauche du MFP et fixer provisoirement le
support avant gauche (G) à l'aide de 2 vis
M4 × 20 (P).
17.Inserte los 2 salientes (33) del soporte fron-

tal izquierdo (G) en los orificios de la cubi-
erta izquierda de la MFP y ajuste
temporariamente el soporte frontal izquierdo
(G) en posición con los 2 tornillos M4 × 20
(P).
17.Setzen Sie die 2 Vorsprünge (33) der vor-

deren linken Stütze (G) in die Öffnungen der
linken Abdeckung am MFP ein und befesti-
gen Sie die vordere linke Stütze (G) provi-
sorisch mit den 2 M4 × 20 Schrauben (P).
17.Inserire le 2 parti sporgenti (33) sul supporto

anteriore sinistro (G) nei fori nel coperchio
sinistro sull'MFP e stringere temporanea-
mente il supporto anteriore sinistro (G) in
posizione con le 2 viti M4 × 20 (P).
17.将左前部支架 (G) 的 2 处突出部 (33) 插入

MFP 主机的左盖板的孔中，使用 2 颗 M4×20
螺丝 (P) 临时固定左前部支架 (G)。
17.좌측 앞 받침대 (G) 의 돌기 (33) 2 군데를

MFP 본체의 좌측커버의 구멍에 넣고 나사
M4×20(P) 2 개로 좌측앞 받침대 (G) 를 반
정도 조입니다 .
17.左前ステー(G) の 2 箇所の突起 (33) を MFP

本体の左カバーの穴に入れ、ビス M4×20(P)
2 本で左前ステー(G) を仮締めする。
8
H
35
H O
36 37
G
34
18.Position the eject unit (H) so that its rail section (34) is inside the MFP, insert the projection (35) on the rear into the hole in the side plate and then
place the front end onto the plate section (37) on the front left stay (G).
NOTICE
When installing the eject unit (H), take care not to pinch the drive unit cable (36).
19.Fully tighten the 2 M4 × 20 screws (P) that were temporarily fastened in step 17 and secure the front left stay (G).
20.Secure the eject unit (H) with the 2 M4 × 8 screws (O).
18.Positionner l'unité d'éjection (H) de sorte que sa partie glissière (34) se trouve dans le MFP, insérer la projection arrière (35) dans le trou de la tôle
latérale puis placer l'extrémité avant sur la partie plaque (37) du support avant gauche (G).
AVIS
À l'installation de l'unité d'éjection (H), attention à ne pas coincer le câble de l'unité d'entraînement (36).
19.Serrer à fond les 2 vis M4 × 20 (P) provisoirement serrées à l'étape 17 et fixer le support avant gauche (G).
20.Fixer l'unité d'éjection (H) avec 2 vis M4 × 8 (O).
18.Coloque la unidad de salida (H) de forma tal que la sección de su carril (34) quede dentro de la MFP, inserte el saliente (35) de la parte posterior en el
orificio de la placa lateral y, a continuación, coloque el extremo frontal sobre la sección de la placa (37) del soporte frontal izquierdo (G).
AVISO
Cuando instale la unidad de salida (H) tenga cuidado de no pinzar el cable de la unidad de accionamiento (36).
19.Apriete totalmente los 2 tornillos M4 × 20 (P) que ajustó temporariamente en el paso 17 y asegure el soporte frontal izquierdo (G).
20.Asegure la unidad de salida (H) con los 2 tornillos M4 × 8 (O).
18.Richten Sie die Auswerfeinheit (H) so aus, dass der Schienenabschnitt (34) im MFP sitzt, setzen Sie den Vorsprung (35) auf der Rückseite in die Öff-
nung der Seitenplatte ein und setzen Sie dann das Vorderteil auf den Plattenabschnitt (37) an der vorderen linken Stütze (G).
HINWEIS
Achten Sie beim Montieren der Auswerfeinheit (H) darauf, dass das Kabel (36) der Antriebseinheit nicht eingeklemmt wird.
19.Ziehen Sie die in Schritt 17 provisorisch angezogenen 2 M4 × 20 Schrauben (P) vollständig an und sichern Sie die vordere linke Stütze (G).
20.Befestigen Sie die Auswerfeinheit (H) mit den 2 M4 × 8 Schrauben (O).
18.Posizionare l'unità di espulsione (H) in modo che la sua sezione di rotaia (34) sia all'interno dell'MFP, inserire la parte sporgente (35) sul retro, nel foro
nella piastra laterale e quindi posizionare il terminale anteriore sulla sezione della piastra (37) sul supporto anteriore sinistro (G).
NOTIFICA
Quando si installa l'unità di espulsione (H), fare attenzione a non schiacciare il cavo dell'unità guida (36).
19.Stringere completamente le 2 viti M4 × 20 (P) che sono state strette temporaneamente nel punto 17 e fissare il supporto anteriore sinistro (G).
20.Fissare l'unità di espulsione (H) con le 2 viti M4 × 8 (O).
18.将排纸单元 (H) 的导轨部分 (34) 靠 MFP 主机内侧设置，将后部的突出部 (35) 插入侧板的孔中，将前部放在左前部支架 (G) 的托板部 (37) 上。
注意
安装排纸单元 (H) 时，必须注意不要夹住驱动单元的电线 (36)。
19.将步骤 17 中临时固定的 2 颗 M4×20 螺丝 (P) 拧紧，以固定左前部支架 (G)。
20.使用 2 颗 M4×8 螺丝 (O) 来固定排纸单元 (H)。
18.배출 유니트 (H) 의 레일부분 (34) 이 MFP 본체의 안쪽이 되게 세트하고 뒷쪽의 돌기 (35) 를 측면판 구멍에 넣어 앞쪽 좌측 받침대 (G) 의 플레이트부
(37) 에 얹습니다 .
주의
배출 유니트 (H) 를 부착할 때에는 구동 유니트의 전선 (36) 을 끼지 않도록 주의합니다 .
19.순서 17 에서 반정도 조인 나사 M4×20(P) 2 개를 완전히 조이고 좌측 앞 받침대 (G) 를 고정합니다 .
20.나사 M4×8(O) 2 개로 배출 유니트 (H) 를 고정합니다 .
18.排出ユニット (H) のレール部分 (34) が MFP 本体の内側にくるようにセットし、後側の突起 (35) を側板の穴に入れ、前側を左前ステー(G) のプレート

部 (37) に乗せる。
注意
排出ユニット (H) を取り付ける時は駆動ユニットの電線 (36) を挟まないように注意する。
19.手順 17 で仮締めしたビス M4×20(P)2 本を本締めし、左前ステー(G) を固定する。
20.ビス M4×8(O)2 本で排出ユニット (H) を固定する。
9
40
38
H
G
J
I 39 O J
21.Plug the 3 connectors (38) into the eject unit 23.Position the upper front cover (J) so that the screw housing (39) is not touching the front left stay
(H) and MFP. (G) and align the projections (40) with the 2 holes on the right side of the upper front cover (J)
22.Secure the cables with the 2 wire stoppers before attaching the upper front cover (J) and securing it in place with the M4 × 8 screw (O).
(I).
21.Enficher les 3 connecteurs (38) dans l'unité 23.Positionner le couvercle supérieur avant (J) de sorte que le logement de la vis (39) ne soit pas en
d'éjection (H) et le MFP. contact avec le support avant gauche (G) et aligner les projections (40) avec les 2 trous du côté
22.Fixer les câbles à l'aide des 2 butées de droit du couvercle supérieur avant (J) avant de fixer ce couvercle supérieur avant (J) à l'aide
câble (I). d'une vis M4 × 8 (O).
21.Enchufe los 3 conectores (38) en la unidad 23.Coloque la cubierta frontal superior (J) de forma tal que el alojamiento del tornillo (39) no toque el
de salida (H) y la MFP. soporte frontal izquierdo (G) y alinee los salientes (40) con los 2 orificios del lado derecho de la
22.Asegure los cables con los 2 topes para cubierta frontal superior (J) antes de instalar la cubierta frontal superior (J) y asegurarla en
cables (I). posición con el tornillo M4 × 8 (O).
21.Stecken Sie die 3 Stecker (38) in die Aus- 23.Positionieren Sie die obere vordere Abdeckung (J) so, dass das Schraubengehäuse (39) nicht
werfeinheit (H) und den MFP. die vordere linke Stütze (G) berührt und richten Sie die Vorsprünge (40) auf die 2 Öffnungen an
22.Befestigen Sie die Kabel mit den 2 Kabelhal- der rechten Seite der oberen vorderen Abdeckung (J) aus, bevor Sie die obere vordere Abdeck-
tern (I). ung (J) anbringen und mit der M4 × 8 Schraube (O) sichern.
21.Collegare i 3 connettori (38) all'unità di 23.Posizionare il coperchio superiore anteriore (J) in modo che l'alloggiamento delle viti (39) non
espulsione (H) e all'MFP. tocchi il supporto anteriore sinistro (G), e allineare le parti sporgenti (40) con i 2 fori sul lato destro
22.Fissare i cavi con i 2 fermacavo (I). del coperchio superiore anteriore (J) prima di applicare il coperchio superiore anteriore (J) e fis-
sarlo in posizione con la vite M4 × 8 (O).
21.使用 3 个接插件 (38) 来连接排纸单元 (H) 以 23.设置前上部盖板 (J)，注意避免其左侧的螺丝固定部 (39) 碰到左前部支架 (G)，将前上部盖板 (J)
及 MFP 主机。右侧的 2 处孔与突出部 (40) 对齐后安装前上部盖板 (J)，使用 1 颗 M4×8 螺丝 (O) 来固定。
22.使用 2 个电线固定夹 (I) 来固定电线。
21.커넥터 (38) 3 개를 배출 유니트 (H) 및 MFP 23.전면 상커버 (J) 좌측의 나사 고정부 (39) 가 좌측 앞 받침대 (G) 에 닿지 않도록 세트하고 전면 상
본체에 접속합니다 . 커버 (J) 우측 구멍 돌기 (40) 2 곳를 맞춰 전면 상커버 (J) 를 부착 , 나사 M4×8(O) 1 개로 고정
22.와이어 스토퍼 (I) 2 개로 전선을 고정합니다 합니다 .
.
21.コネクター(38)3 個を排出ユニット (H) お 23.前上カバー(J) 左側のビス止め部 (39) が左前ステー(G) に当たらないようセットし、前上カバー

よび MFP 本体に接続する。 (J) 右側の穴 2 箇所に突起 (40) を合わせてから前上カバー(J) を取り付け、ビス M4×8(O)1 本で
22.ワイヤーストッパー(I)2 個で電線を固定す固定する。
る。
10
B
O
14
12
C
41
O
10 G
11 K
24.Install the front right cover (14) using the 25.Fit the paper entry unit cover (C) onto the 26.Insert the 2 projections (41) on the left con-
screw (12) removed in step 8. paper entry unit (B). nection cover (K) into the holes in the front
Secure the fan cover (10) using the screw left stay (G) and secure the cover with the 2
(11) removed in step 7. M4 × 8 screws (O).
* Check that connector on the inside of the
fan cover (10) has not been dislodged.
24.Reposer le couvercle avant droit (14) à l'aide 25.Monter le couvercle de l'unité d'entrée du 26.Insérer les 2 projections (41) du couvercle
de la vis (12) déposée à l'étape 8. papier (C) sur l'unité d'entrée du papier (B). de connexion gauche (K) dans les trous du
Fixer le couvercle du ventilateur (10) à l'aide support avant gauche (G) et fixer le couver-
de la vis (11) déposée à l'étape 7. cle à l'aide de 2 vis M4 × 8 (O).
* Vérifier que le connecteur à l'intérieur du
couvercle du ventilateur (10) n'a pas bougé.
24.Instale la cubierta frontal derecha (14) 25.Coloque la cubierta de la unidad de ingreso 26.Inserte los 2 salientes (41) de la cubierta de
usando el tornillo (12) quitado en el paso 8. de papel (C) en la unidad de ingreso de conexiones izquierda (K) en los orificios del
Asegure la cubierta del ventilador (10) papel (B). soporte frontal izquierdo (G) y asegure la
usando el tornillo (11) quitado en el paso 7. cubierta con los 2 tornillos M4 × 8 (O).
* Compruebe si no se desplazó el conector
del interior de la cubierta del ventilador (10).
24. Bringen Sie die vordere rechte Abdeckung (14) 25.Setzen Sie die Abdeckung (C) der Papiere- 26.Setzen Sie die 2 Vorsprünge (41) an der
mit der in Schritt 8 entfernten Schraube (12) an. inzugseinheit in die Papiereinzugseinheit (B) linken Verbindungsabdeckung (K) in die Öff-
Befestigen Sie die Lüfterabdeckung (10) mit der ein. nungen der vorderen linken Stütze (G) ein
in Schritt 7 entfernten Schraube (11). und befestigen Sie die Abdeckung mit den 2
* Vergewissern Sie sich, dass der Stecker auf M4 × 8 Schrauben (O).
der Innenseite der Lüfterabdeckung (10) nicht
abgetrennt wurde.
24.Installare il coperchio anteriore destro (14) 25.Applicare il coperchio (C) dell'unità di 26.Inserire le 2 parti sporgenti (41) sul coper-
utilizzando la vite (12) rimossa nel punto 8. ingresso carta, sull'unità di ingresso carta chio connessione sinistro (K) nei fori del sup-
Fissare il coperchio ventola (10) utilizzando (B). porto anteriore sinistro (G) e quindi fissare il
la vite (11) rimossa nel punto 7. coperchio con le 2 viti M4 × 8 (O).
* Controllare che il connettore sull'interno del
coperchio della ventola (10) non sia stato
rimosso.
24.使用在步骤 8 中卸下的 1 颗螺丝 (12) 来固定 25.将进纸单元盖板 (C) 安装在进纸单元 (B) 26.连接左盖板 (K) 的 2 处突出部 (41) 插入左前
右前盖板 (14)。上。部支架 (G) 的孔中，使用 2 颗 M4×8 螺丝 (O)
使用在步骤 7 中卸下的 1 颗螺丝 (11) 来固定来固定。
风扇盖板 (10)。
※ 确认位于风扇盖板 (10) 内侧的接插件有
无露出。
24.순서 8 에서 제거한 나사 (12) 1 개로 오른쪽 25.반입 유니트 커버 (C) 를 반입 유니트 (B) 에 26.연결 좌측커버 (K) 의 돌기 (41) 2 곳을 좌측
전면커버 (14) 를 부착합니다 . 부착합니다 . 앞 받침대 (G) 의 구멍에 넣고 나사
순서 7 에서 제거한 나사 (11) 1 개로 팬커버 M4×8(O) 2 개로 고정합니다 .
(10) 를 고정합니다 .
※ 팬커버 (10) 안쪽에 있는 커넥터가 빠져
있지 않은지를 확인합니다 .
24.手順 8 で取り外したビス (12)1 本で右前カ 25.搬入ユニットカバー(C) を搬入ユニット (B) 26.連結左カバー(K) の突起 (41)2 箇所を左前
バー(14) を取り付ける。に取り付ける。ステー(G) の穴に入れ、ビス M4×8(O)2 本で
手順 7 で外したビス (11)1 本でファンカ固定する。
バー(10) を固定する。
※ ファンカバー(10) 内側にあるコネクター
が外れていないことを確認する。
11
L
43
P
R
O P
42
27.Remove the interface cover (42). 29.Open the eject cover (43). 31.Attach the lower connection cover (R) with
* After installing the document finisher, re- 30.Attach the upper left cover (M) and close the the 2 M4 × 20 screws (P).
attach the interface cover (42). eject cover (43).
28.Secure the left cover (L) using the 2 M4 × 8
screws (O).
27.Déposer le couvercle d'interface (42). 29.Ouvrir le couvercle d'éjection (43). 31.Fixer le couvercle de connexion inférieur (R)
* Après avoir installé le retoucheur de docu- 30.Fixer le couvercle supérieur gauche (M) et à l'aide de 2 vis M4 × 20 (P).
ment, reposer le couvercle d'interface (42). fermer le capot d’éjection (43).
28.Fixer le couvercle gauche (L) à l'aide de 2
vis M4 × 8 (O).
27.Quite la cubierta de la interfaz (42). 29.Abra la cubierta de expulsión (43). 31.Fije la cubierta de conexiones inferior (R)
* Después de instalar el finalizador de docu- 30.Fije la cubierta superior izquierda (M) y con los 2 tornillos M4 × 20 (P).
mentos, vuelva a colocar la cubierta de la cierre la cubierta de expulsión (43).
interfaz (42).
28.Asegure la cubierta izquierda (L) usando los
2 tornillos M4 × 8 (O).
27.Entfernen Sie die Schnittstellenabdeckung 29.Öffnen Sie die Auswerfabdeckung (43). 31.Bringen Sie die untere Verbindungsabdeck-
(42). 30.Bringen Sie die obere linke Abdeckung (M) ung (R) mit den 2 M4 × 20 Schrauben (P)
* Bringen Sie nach der Installation des Doku- wieder an und schließen Sie die Auswerfab- an.
ment-Finishers wieder die Schnittstellenab- deckung (43).
deckung (42) an.
28.Befestigen Sie die linke Abdeckung (L) mit
den 2 M4 × 8 Schrauben (O).
27.Rimuovere la copertura di interfaccia (42). 29.Aprire il coperchio di espulsione (43). 31.Fissare il coperchio connessione inferiore
* Dopo l'installazione della finitrice di docu- 30.Fissare il coperchio superiore sinistro (M) e (R) con le 2 viti M4 × 20 (P).
menti, fissare di nuovo la copertura di inter- chiudere il coperchio di espulsione (43).
faccia (42).
28.Fissare il coperchio sinistro (L) utilizzando le
2 viti M4 × 8 (O).
27.拆下接口盖板 (42)。 29.打开排纸盖板 (43)。 31.使用 2 颗 M4×20 螺丝 (P) 来安装连接下盖板

※ 在装订器设置完成后，按原样安装接口盖 30.安装左上部盖板 (M)，关闭排纸盖板 (43)。 (R)。
板 (42)。
28.使用 2 颗 M4×8 螺丝 (O) 来固定左盖板 (L)。
27.인터페이스 커버 (42) 를 제거합니다 . 29.배출커버 (43) 를 엽니다 . 31.나사 M4×20(P) 2 개로 연결 하커버 (R) 를
※ 인터페이스 커버 (42) 는 문서 피니셔 설 30.좌측 상커버 (M) 를 부착하고 배출커버 (43) 장착합니다 .
치 후에 원래대로 장착합니다 . 를 닫습니다 .
28.좌측 커버 (L) 를 나사 M4×8(O) 2 개로 고정
합니다 .
27.インターフェイスカバー(42) を取り外す。 29.排出カバー(43) を開く。 31.ビス M4×20(P)2 本で連結下カバー(R) を取

※ インターフェイスカバー(42) はドキュメ 30.左上カバー(M) を取り付け、排出カバー(43) り付ける。
ントフィニッシャー設置後に、元通り取り付を閉じる。
ける。
28.左カバー(L) をビス M4×8(O)2 本で固定す
る。
12
N
N Q
45
44
44 46
45
32.Pull the 2 slide rails (44) out from inside the 34.Move the slide rails (44) backwards and secure the paper conveying unit (N) to the 4 hooks (45).
MFP. Check that the hooks are securely engaged through the opening (46).
33.Align the 4 hooks (45) on the slide rails (44) 35.Lift the rear right side of the paper conveying unit (N) slightly while pushing it firmly in as far as it
with the notched sections of the paper con- will go. After pushing it all the way in, pull it out again and check that it stops mid-way.
veying unit (N) and fit the paper conveying 36.Secure the paper conveying unit (N) with the P Tite screw M3 × 8 (Q).
unit (N) onto the slide rails (44). 37.Close the front cover (7).
32.Sortir les 2 glissières coulissantes (44) hors 34.Remettre les glissières coulissantes (44) en place et fixer l'unité de transport du papier (N) avec
du MFP. les 4 crochets (45). Vérifier que les crochets sont soigneusement engagés dans les ouvertures
33.Aligner les 4 crochets (45) des glissières (46).
coulissantes (44) avec les encoches de 35.Lever légèrement le côté arrière droit de l'unité de transport du papier (N) tout en pousant cette
l'unité de transport du papier (N) et insérer unité à fond. Une fois poussée à fond, tirer sur l'unité et vérifier qu'elle s'arrête à mi-course.
l'unité de transport du papier (N) sur ces glis- 36.Fixer l'unité de transport du papier (N) à l'aide d'une vis P Tite M3 x 8 (Q).
sières coulissantes (44). 37.Refermer le capot avant (7).
32.Tire de los 2 carriles deslizantes (44) para 34. Mueva los carriles deslizantes (44) hacia atrás y asegure la unidad de transporte de papel (N) a los 4 gan-
sacarlos de la MFP. chos (45). A través de la abertura (46), compruebe si los ganchos están enganchados de forma segura.
33.Alinee los 4 ganchos (45) de los carriles 35. Levante ligeramente el lado trasero derecho de la unidad de transporte de papel (N) mientras presiona
deslizantes (44) con las secciones con firmemente hasta el fondo. Después de empujarla hasta el fondo, vuelva a sacarla y compruebe si se
muescas de la unidad de transporte de detiene en la mitad del recorrido.
papel (N) y encaje la unidad de transporte 36. Asegure la unidad de transporte de papel (N) con el tornillo P Tite M3 × 8 (Q).
de papel (N) en los carriles deslizantes (44). 37. Cierre la cubierta frontal (7).
32.Ziehen Sie die 2 Schlittenschienen (44) aus 34. Verschieben Sie die Schlittenschienen (44) nach hinten und befestigen Sie die Papierfördereinheit (N) mit
dem MFP heraus. den 4 Haken (45). Vergewissern Sie sich durch die Öffnung (46), dass die Haken ordnungsgemäß greifen.
33.Richten Sie die 4 Haken (45) der Schlitten- 35. Heben Sie die hintere rechte Seite der Papierfördereinheit (N) leicht an und drücken Sie sie gleichzeitig bis
schienen (44) auf die Einkerbungen der zum Anschlag einwärts. Ziehen Sie sie nach dem Hineindrücken bis zum Anschlag wieder heraus und ver-
Papierfördereinheit (N) aus und setzen Sie gewissern Sie sich, dass sie mittendrin anhält.
die Papierfördereinheit (N) auf die Schlitten- 36. Befestigen Sie die Papierfördereinheit (N) mit der P-Tite-Schraube M3 × 8 (Q).
schienen (44). 37. Schließen Sie die vordere Abdeckung (7).
32.Estrarre le 2 rotaie di scorrimento (44) 34.Spostare le rotaie di scorrimento (44) all'indietro e fissare l'unità di trasporto carta (N) ai 4 ganci
dall'interno dell'MFP. (45). Controllare che i ganci siano innestati in modo sicuro attraverso l'apertura (46).
33.Allineare i 4 ganci (45) sulle rotaie di scorri- 35.Sollevare leggermente il lato posteriore destro dell'unità di trasporto carta (N) mentre lo si spinge
mento (44) con le sezioni intagliate dell'unità fermamente fino in fondo. Dopo averlo spinto fino in fondo, estrarlo di nuovo e controllare che si
di trasporto carta (N), ed inserire l'unità di arresti a metà corsa.
trasporto carta (N) sulle rotaie di scorrimento 36.Fissare l'unità di trasporto carta (N) con la vite P Tite M3 × 8 (Q)
(44). 37.Chiudere il pannello anteriore (7).
32.拉出机身内的 2 根滑轨 (44)。 34.将滑轨 (44) 向后方移动，使输纸单元 (N) 固定在 4 处卡扣 (45) 上。通过开口部（46）来确认是否
33.将输纸单元 (N) 的缺口部与滑轨 (44) 的 4 处确实卡入卡扣。
卡扣 (45) 对齐，将输纸单元 (N) 放在滑轨 35.将输纸单元 (N) 的右后部稍稍抬起的同时，将其插入到底。插入到底后再将其拉出，确认是否在中
(44) 上。途停止。
36.使用 1 颗紧固型 P 螺丝 M3×8(Q) 来固定输纸单元 (N)。
37.关闭前盖板 (7)。
32.기내의 슬라이드 레일 (44) 2 개를 빼 냅니다 . 34.슬라이드 레일 (44) 을 뒷 방향으로 움직여 4 곳의 후크 (45) 에 반송 유니트 (N) 을 고정시킵니다
33.슬라이드 레일 (44) 4 곳의 후크 (45) 에 반송 . 확실히 후크에 걸린 것을 개구부（46）에서 확인합니다 .
유니트 (N) 를 맞춰 반송 유니트 (N) 를 슬라 35.반송 유니트 (N) 오른쪽 뒤쪽을 조금 들어 올리면서 안까지 확실히 삽입합니다 . 안까지 삽입한
이드 레일 (44) 에 얹습니다 . 후 앞으로 당겨 도중에 멈추는지를 확인합니다 .
36.나사 M3×8P Tight (Q) 1 개로 반송 유니트 (N) 를 고정합니다 .
37.전면 커버 (7) 을 닫습니다 .
32.胴内のスライドレール (44)2 本を引き出す。 34.スライドレール (44) を後方向に動かし、4 箇所のフック (45) に搬送ユニット (N) を固定させ
33.スライドレール (44) の 4 箇所のフックる。確実にフックに掛かったことを、開口部（46）から確認する。
(45) に搬送ユニット (N) の切り欠き部を合 35.搬送ユニット (N) の右後側を少し持ち上げながら、奥までしっかり挿入する。奥まで挿入した後、
わせて搬送ユニット (N) をスライドレール手前に引き出し、途中で止まることを確認する。
(44) に載せる。 36.ビス M3×8P タイト (Q)1 本で搬送ユニット (N) を固定する。
37.前カバー(7) を閉める。
13
HOLE PUNCH UNIT
B
F
C
A H I
D E
E. Spring......................................................... 1 Be sure to remove any tape and/or cushioning

English
F. Punch PWB ............................................... 1 material from supplied parts.
Supplied parts G. Waste hole punch box ............................... 1
A. Punch guide............................................... 1 H. M3 × 8 tap Tight S screw ........................... 3
B. Hole punch unit.......................................... 1 I. Label .......................................................... 1
C. Motor unit................................................... 1
D. Stop ring .................................................... 1
E. Ressort ...................................................... 1 Veillez à retirer les morceaux de bande adhé-

Français
F. PWB de la perforatrice............................... 1 sive et/ou les matériaux de rembourrage des
Pièces fournies G. Bac de récupération de la perforatrice....... 1 pièces fournies.
A. Guide de perforatrice................................. 1 H. Vis S taraudée M3 × 8 ............................... 3
B. Perforatrice ................................................ 1 I. Étiquette..................................................... 1
C. Moteur ....................................................... 1
D. Bague d'arrêt ............................................. 1
E. Resorte ...................................................... 1 Asegúrese de despegar todas las cintas y/o

Español
F. PWB de perforación................................... 1 material amortiguador de las partes suministra-
Partes suministradas G. Caja para desechos de la perforación ....... 1 das.
A. Guía de perforación................................... 1 H. Tornillo de ajuste M3 × 8........................... 3
B. Perforadora................................................ 1 I. Etiqueta...................................................... 1
C. Unidad motriz ............................................ 1
D. Anillo de tope............................................. 1
E. Feder ......................................................... 1 Entfernen Sie Klebeband und/oder Dämpfungs-

Deutsch
F. Locher-PWB .............................................. 1 material vollständig von den mitgelieferten
Gelieferte Teile G. Lochungsabfallbehälter.............................. 1 Teilen.
A. Locherführung ........................................... 1 H. M3 × 8 Passstift-Verbundschrauben.......... 3
B. Lochereinheit ............................................. 1 I. Aufkleber.................................................... 1
C. Motoreinheit............................................... 1
D. Anschlagring.............................................. 1
E. Molla .......................................................... 1 Accertarsi di rimuovere tutti i nastri adesivi e/o il

Italiano
F. Scheda a circuiti stampati di perforazione .... 1 materiale di imbottitura dalle parti fornite.
Parti di fornitura G. Scarto perforazione ................................... 1
A. Guida perforazione .................................... 1 H. Viti con testa a croce S M3 × 8 .................. 3
B. Unità di perforazione ................................. 1 I. Etichetta..................................................... 1
C. Unità motore .............................................. 1
D. Anello di bloccaggio................................... 1
简体中文 E. 弹簧 .................................1 如果附属品上带有固定胶带，缓冲材料时务必揭

F. 打孔单元电路板 .......................1 下。
附属品 G. 打孔纸屑盒 ...........................1
A. 打孔导向板........................... 1 H. M3 X 8 攻丝紧固型 S 螺丝 ..............3
B. 打孔单元............................. 1 I. 标签 .................................1
C. 电机单元............................. 1
D. 止动环............................... 1
한국어 E. 스프링............................................... 1 동봉품에 고정 테이프 , 완충재가 붙어 있는 경

F. 펀치기판............................................ 1 우에는 반드시 제거할 것 .
동봉품 G. 펀치폐기박스...................................... 1
A. 펀치가이드......................................... 1 H. 나사 M3×8 탭타이트 S......................... 3
B. 펀치유니트......................................... 1 I. 라벨.................................................. 1
C. 모터유니트......................................... 1
D. 스톱링............................................... 1
日本語 E. バネ .................................1 同梱品に固定テープ、緩衝材が付いている場合

F. パンチ基板 ...........................1 は必ず取り外すこと。
同梱品 G. パンチくずボックス ...................1
A. パンチガイド......................... 1 H. ビス M3×8 タップタイト S .............3
B. パンチユニット....................... 1 I. ラベル ...............................1
C. モーターユニット..................... 1
D. ストップリング....................... 1
1
2 4
1
3
Procedure Removing the cover (DF-770) 2.Remove the 2 screws (3) and remove the
Before installing the hole punch unit, make sure If installing on the DF-790, proceed to step 1 on upper rear cover (4).
the MFP's main power switch is turned off and page 3.
that its power cord is unplugged from the power 1.Remove the screw (1) and remove the small
outlet. rear cover (2).
Procédure Dépose du couvercle (DF-770) 2.Déposer les 2 vis (3) et déposer le couvercle
Avant d’installer la perforatrice, s’assurer que Pour l'installation sur le modèle DF-790, passer supérieur arrière (4).
l’interrupteur d’alimentation principal du MFP est à l'étape 1 de la page 3.
hors tension et que le câble d’alimentation est 1.Déposer la vis (1) et déposer le petit couver-
débranché de la prise secteur. cle arrière (2).
Procedimiento Extracción de la cubierta (DF-770) 2.Quite los 2 tornillos (3) y, después, quite la
Antes de instalar la perforadora, asegúrese de Si realiza la instalación en el DF-790, vaya al cubierta trasera superior (4).
que el interruptor principal de la alimentación paso 1 de la página 3.
del MFP esté desconectado y de que el cable 1.Quite el tornillo (1) y, después, quite la cubi-
de alimentación esté desenchufado de la toma erta trasera pequeña (2).
de corriente de la pared.
Verfahren Entfernen der Abdeckung (DF-770) 2.Die 2 Schrauben (3) entfernen und die obere
Bevor Sie mit dem Einbau der Lochereinheit Zur Installation des DF-790 weitergehen zu hintere Abdeckung (4) abnehmen.
beginnen, stellen Sie sicher, dass der Schritt 1 auf Seite 3.
Hauptschalter des Kopierers ausgeschaltet und 1.Die Schraube (1) entfernen und die kleine
das Netzkabel aus der Steckdose gezogen ist. hintere Abdeckung (2) abnehmen.
Procedura Rimozione del coperchio (DF-770) 2.Rimuovere le 2 viti (3) e quindi rimuovere il
Prima di installate l'unità di perforazione, assicu- Se si installa sull'unità DF-790, procedere al pannello superiore posteriore (4).
rarsi che l'interruttore principale dell'MFP sia passo 1 a pagina 3.
spento e che il cavo di alimentazione sia scolle- 1.Rimuovere la vite (1) e quindi rimuovere il
gato dalla presa di corrente. pannello posteriore piccolo (2).
安装步骤拆下盖板（DF-770 时） 2.拆除 2 颗螺丝 (3)，拆下后上部盖板 (4)。

安装打孔单元时，必须事先关闭 MFP 主机的主电安装到 DF-790 上时，跳至 P3 的步骤 1。
源开关，并拔下电源插头后再进行作业。 1.拆除 1 颗螺丝 (1)，拆下后部小盖板 (2)。
설치순서 커버제거（DF-770 의 경우） 2.나사 (3) 2 개를 제거하고 뒷 상커버 (4) 를

펀치유니트를 부착할 때에는 반드시 MFP 본체 DF-790 에 장착하는 경우에는 P3 의 순서 1 로 제거합니다 .
의 주 전원 스위치를 OFF 로 하고 전원플러그를 진행합니다 .
뺀 다음 작업을 할 것 . 1.나사 (1) 1 개를 제거하고 뒷 소커버 (2) 를
제거합니다 .
取付手順カバーの取り外し（DF-770 の場合） 2.ビス (3)2 本を外し、後上カバー(4) を取り

パンチユニットを設置するときは、必ず MFP 本 DF-790 に装着の場合は、 P3 の手順 1 へ進む。外す。
体の主電源スイッチを OFF にし、電源プラグを 1.ビス (1)1 本を外し、後小カバー(2) を取り
抜いてから作業すること。外す。
2
6
10
7
5 7
7 9
Removing the cover (DF-790) 2.Remove the 3 screws (7) and remove the Installing the hole punch unit
1.Remove the screw (5) and remove the small upper rear cover (8). 3.Remove the screw (9) and pull the guide
rear cover (6). (10) outwards.
Dépose du couvercle (DF-790) 2.Déposer les 3 vis (7) et déposer le couvercle Installation de la perforatrice
1.Déposer la vis (5) et déposer le petit couver- supérieur arrière (8). 3.Déposer la vis (9) et tirer le guide (10) vers
cle arrière (6). l'extérieur.
Extracción de la cubierta (DF-790) 2.Quite los 3 tornillos (7) y, después, quite la Instalación de la perforadora
1.Quite el tornillo (5) y, después, quite la cubi- cubierta trasera superior (8). 3.Quite el tornillo (9) y tire de la guía (10)
erta trasera pequeña (6). hacia fuera.
Entfernen der Abdeckung (DF-790) 2.Die 3 Schrauben (7) entfernen und die obere Anbringen der Lochereinheit
1.Die Schraube (5) entfernen und die kleine hintere Abdeckung (8) abnehmen. 3.Die Schraube (9) entfernen und die Führung
hintere Abdeckung (6) abnehmen. (10) nach außen ziehen.
Rimozione del coperchio (DF-790) 2.Rimuovere le 3 viti (7) e quindi rimuovere il Installare l’unità di perforazione
1.Rimuovere la vite (5) e quindi rimuovere il pannello superiore posteriore (8). 3.Rimuovere la vite (9) ed estrarre la guida
pannello posteriore piccolo (6). (10) verso l'esterno.
拆下盖板（DF-790 时） 2.拆除 3 颗螺丝 (7)，拆下后上部盖板 (8)。安装打孔单元

1.拆除 1 颗螺丝 (5)，拆下后部小盖板 (6)。 3.拆除 1 颗螺丝 (9)，将导向板 (10) 向外拉
出。
커버제거（DF-790 의 경우） 2.나사 (7) 3 개를 제거하고 뒷 상커버 (8) 를 펀치유니트 부착

1.나사 (5) 1 개를 제거하고 뒷 소커버 (6) 를 제거합니다 . 3.나사 (9) 1 개를 제거하고 가이드 (10) 을 앞
제거합니다 . 으로 끌어 당깁니다 .
カバーの取り外し（DF-790 の場合） 2.ビス (7)3 本を外し、後上カバー(8) を取りパンチユニットの取り付け

1.ビス (5)1 本を外し、後小カバー(6) を取り外す。 3.ビス (9)1 本を外し、ガイド (10) を手前に引
外す。き出す。
3
12
B
11
4.Install the punch guide (A) so that the leading edge of the guide (11) is below the document fin- 5.Insert the hole punch unit (B) into the docu-
isher frame (12). ment finisher.
4.Monter le guide de la perforatrice (A) de sorte que le bord d'attaque du guide (11) se trouve sous 5.Insérer la perforatrice (B) dans le retoucheur
le bâti du retoucheur de document (12). de document.
4.Instale la guía de perforación (A) de forma tal que el borde delantero de la guía (11) quede 5.Inserte la perforadora (B) en el finalizador de
debajo de la carcasa del finalizador de documentos (12). documentos.
4.Die Locherführung (A) so einsetzen, dass die Vorderkante der Führung (11) unter dem Rahmen 5.Die Lochereinheit (B) in den Dokument-Fin-
(12) des Dokument-Finishers liegt. isher einsetzen.
4.Installare la guida perforazione (A) in modo che il bordo principale della guida (11) sia sotto il 5.Inserire l'unità di perforazione (B) nella fini-
telaio (12) della finitrice di documenti. trice di documenti.
4.将打孔导向板 (A) 的前端 (11) 安装在装订器的框架 (12) 的下部。 5.将打孔单元 (B) 插入到装订器中。
4.펀치가이드 (A) 의 끝 (11) 이 문서 피니셔의 프레임 (12) 밑으로 되도록 장착합니다 . 5.펀치유니트 (B) 를 문서 피니셔에 삽입합니
다.
4.パンチガイド (A) の先端 (11) がドキュメントフィニッシャーのフレーム (12) の下になるよう 5.パンチユニット (B) をドキュメントフィ
に取り付ける。ニッシャーに挿入する。
4
B
C
13 16
B
15
14
C
C
6.Raise the hole punch unit (B) slightly and fit the hook (13) on the motor unit (C) into the groove 7.Secure the motor unit (C) with the 2 screws
(14) in the document finisher. At the same time, insert the rod (15) on the motor unit (C) into the (H).
hole (16) in the hole punch unit (B).
6.Lever légèrement la perforatrice (B) et insérer le crochet (13) du moteur (C) dans la rainure (14) 7.Fixer le moteur (C) à l'aide de 2 vis (H).
du retoucheur de document. Insérer en même temps la tige (15) du moteur (C) dans le trou (16)
de la perforatrice (B).
6.Levante ligeramente la perforadora (B) y encaje el gancho (13) de la unidad motriz (C) en la 7.Asegure la unidad motriz (C) con los 2 tornil-
ranura (14) del finalizador de documentos. Al mismo tiempo, inserte la varilla (15) de la unidad los (H).
motriz (C) en el orificio (16) de la perforadora (B).
6.Die Lochereinheit (B) leicht anheben und den Haken (13) an der Motoreinheit (C) in die Nut (14) 7.Die Motoreinheit (C) mit den 2 Schrauben
des Dokument-Finishers einsetzen. Dabei auch die Stange (15) an der Motoreinheit (C) in die (H) sichern.
Öffnung (16) der Lochereinheit (B) einstecken.
6.Sollevare leggermente l'unità di perforazione (B) ed inserire il gancio (13) sull'unità motore (C) 7.Fissare l'unità motore (C) con le 2 viti (H).
nella scanalatura (14) della finitrice di documenti. Contemporaneamente, inserire l'asta (15)
sull'unità motore (C) nel foro (16) dell'unità di perforazione (B).
6.稍稍抬起打孔单元 (B)，将电机单元 (C) 的卡扣 (13) 嵌入装订器的沟槽 (14) 内。与此同时，将电 7.使用 2 颗螺丝 (H) 来固定电机单元 (C)。
机单元 (C) 的轴 (15) 插入打孔单元 (B) 的孔 (16) 中。
6.펀치유니트 (B) 를 조금 들면서 모터유니트 (C) 후크 (13) 를 문서 피니셔의 구 (14) 에 꽂습니다 . 7.나사 (H) 2 개로 모터유니트 (C) 를 고정합니
이것과 동시에 모터유니트 (C) 의 축 (15) 을 펀치유니트 (B) 구멍 (16) 에 삽입합니다 . 다.
6.パンチユニット (B) を少し持ち上げながら、モーターユニット (C) のフック (13) をドキュメン 7.ビス (H)2 本で、
モーターユニット (C) を固
トフィニッシャーの溝 (14) にはめ込む。これと同時に、モーターユニット (C) の軸 (15) をパン定する。
チユニット (B) の穴 (16) に挿入する。
5
17
19
E 15 18
D
8.Fit the stop ring (D) over the motor unit rod 9.Run the hole punch unit wire (17) through
(15) and fit the spring (E) between the hole the motor unit edging (18).
punch unit and motor unit. 10.Plug the wire from the hole punch unit motor
into the connector on the motor unit (19).
8.Monter la bague d'arrêt (D) sur la tige du 9.Faire passer le câble de la perforatrice (17)
moteur (15) et insérer le ressort (E) entre la dans le passage de câbles du moteur (18)
perforatrice et le moteur. 10.Raccorder le câble du moteur de la perfora-
trice au connecteur du moteur (19).
8.Coloque el anillo de tope (D) sobre la varilla 9.Tienda el cable de la perforadora (17) a
de la unidad motriz (15) y coloque el resorte través de la pestaña de la unidad motriz
(E) entre la perforadora y la unidad motriz. (18).
10.Enchufe el cable del motor de la perforadora
al conector de la unidad motriz (19).
8.Den Anschlagring (D) auf die Stange (15) 9.Das Kabel (17) der Lochereinheit durch den
der Motoreinheit setzen und die Feder (E) Kantenschutz (18) der Motoreinheit führen.
zwischen Lochereinheit und Motoreinheit 10.Das Kabel vom Motor der Lochereinheit an
einsetzen. den Steckverbinder der Motoreinheit (19)
anschließen.
8.Inserire l'anello di bloccaggio (D) sull'asta 9.Far passare il cavo dell'unità di perforazione
(15) dell'unità motore ed inserire molla (E) (17) attraverso il bordo (18) dell'unità
tra l'unità di perforazione e l'unità motore. motore.
10.Collegare il cavo dal motore dell'unità di per-
forazione nel connettore sull'unità motore
(19).
8.将止动环 (D) 嵌入到电机单元的轴 (15) 上， 9.将打孔单元的电线 (17) 穿过电机单元的包边

在打孔单元与电机单元之间安装弹簧 (E)。孔 (18)。
10.将来自打孔单元的电机的电线与电机单元的
接插件 (19) 相连接。
8.모터유니트 축 (15) 에 스톱링 (D) 을 꽂고 펀 9.펀치유니트의 전선 (17) 을 모터유니트의 에

치유니트와 모터유니트 사이에 스프링 (E) 징 (18) 에 지나가게 합니다 .
을설치합니다 . 10.펀치유니트 모터에서의 전선을 모터유니트
커넥터 (19) 에 접속합니다 .
8.モーターユニットの軸 (15) にストップリン 9.パンチユニットの電線 (17) をモーターユ

グ (D) をはめ、パンチユニットとモーターユニットのエッジング (18) に通す。
ニットの間にバネ (E) を取り付ける。 10.パンチユニットのモーターからの電線を
モーターユニットのコネクター(19) に接続
する。
6
25
23
21 25
24
F F
20
20
22 H
Installing the punch PWB and waste hole punch box (DF-770) 13.Plug the 6 hole punch unit wires into the con-
If installing on the DF-790, proceed to step 11 on page 9. nectors (25) on the punch PWB (F).
11.Fit the 2 hooks (20) in the punch PWB (F) into the cut (21) in the document finisher. At the same
time, insert the projection (23) on the document finisher into the hole (22) in the punch PWB (F).
12.Using the screw (H), tighten the hole punch unit ground wire (24) and the punch PWB (F)
together.
Installation de la PWB de la perforatrice et du bac de récupération de la perforatrice (DF-770). 13.Raccorder les 6 câbles de la perforatrice aux
Pour une installation sur le modèle DF-790, passer à l'étape 11 en page 9. connecteurs (25) de la PWB de la perfora-
11.Insérer les 2 crochets (20) de la PWB de la perforatrice (F) dans la découpe (21) du retoucheur trice (F).
de document. Insérer en même temps la saillie (23) du retoucheur de document dans le trou (22)
de la PWB de la perforatrice (F).
12.Fixer le câble de terre de la perforatrice (24) à la PWB de la perforatrice (F) à l'aide d'une vis (H).
Instalación del PWB de perforación y la caja para desechos de la perforación (DF-770) 13.Enchufe los 6 cables de la perforadora a los
Si realiza la instalación en el DF-790, vaya al paso 11 de la página 9. conectores (25) del PWB de perforación (F).
11.Coloque los 2 ganchos (20) del PWB de perforación (F) en el corte (21) del finalizador de docu-
mentos. Al mismo tiempo, inserte el resalto (23) del finalizador de documentos en el orificio (22)
del PWB de perforación (F).
12.Usando el tornillo (H), apriete juntos el cable de conexión a tierra de la perforadora (24) y el PWB
de perforación (F).
Installation der Locher-PWB und des Lochungsabfallbehälters (DF-770) 13.Die 6 Kabel der Lochereinheit an die Steck-
Zur Installation des DF-790 weitergehen zu Schritt 11 auf Seite 9. verbinder (25) der Locher-PWB (F)
11.Die 2 Haken (20) in der Locher-PWB (F) in die Aussparung (21) am Dokument-Finisher einset- anschließen.
zen. Dabei auch den Vorsprung (23) am Dokument-Finisher in die Öffnung (22) auf der Locher-
PWB (F) einsetzen.
12.Mit der Schraube (H) das Massekabel (24) der Lochereinheit an der Locher-PWB (F) festziehen.
Installazione della scheda a circuiti stampati di perforazione e dello scarto perforazione (DF-770) 13.Collegare i 6 cavi dell'unità di perforazione
Se si installa sull'unità DF-790, procedere al passo 11 a pagina 9. nei connettori (25) sulla scheda a circuiti
11.Inserire i 2 ganci (20) della scheda a circuiti stampati di perforazione (F) nell'intaglio (21) della stampati di perforazione (F).
finitrice di documenti. Contemporaneamente, inserire la sporgenza (23) sulla finitrice di docu-
menti nel foro (22) della scheda a circuiti stampati di perforazione (F).
12.Utilizzando la vite (H), stringere insieme il cavo di terra (24) dell'unità di perforazione e la scheda
a circuiti stampati di perforazione (F).
安装电路板与打孔纸屑盒（DF-770 时） 13.将打孔单元的 6 根电线与打孔电路板 (F) 的

安装到 DF-790 上时，跳至 P9 的步骤 11。接插件 (25) 相连接。
11.将打孔电路板 (F) 的 2 个卡扣 (20) 挂在装订器的缺口 (21) 上。同时，将打孔电路板 (F) 的孔
(22) 卡入装订器的突出部 (23)。
12.使用 1 颗螺丝 (H) 将打孔单元的接地线 (24) 与打孔电路板 (F) 一起固定。
기판과 펀치폐기박스의 부착（DF-770 의 경우） 13.펀치유니트의 전선 6 선을 펀치기판 (F) 커넥

DF-790 에 장착하는 경우에는 P9 의 순서 11 로 진행합니다 . 터 (25) 에 접속합니다 .
11.펀치기판 (F) 의 후크 (20) 2 곳을 문서 피니셔의 구멍 (21) 에 겁니다 . 동시에 펀치기판 (F) 구멍
(22) 을 문서 피니셔의 돌기 (23) 에 넣습니다 .
12.나사 (H) 1 개로 펀치유니트의 접지선 (24) 과 펀치기판 (F) 을 함게 조입니다 .
基板とパンチくずボックスの取り付け（DF-770 の場合） 13.パンチユニットの電線 6 本を、パンチ基板

DF-790 に装着の場合は、P9 の手順 11 へ進む。 (F) のコネクター(25) に接続する。
11.パンチ基板 (F) のフック (20)2 箇所をドキュメントフィニッシャーの切り欠き (21) に引っ掛け
る。同時に、パンチ基板 (F) の穴 (22) をドキュメントフィニッシャーの突起 (23) に入れる。
12.ビス (H)1 本で、
パンチユニットのアース線 (24) とパンチ基板 (F) を共締めする。
7
28
27
I
26
G
14.Plug the 2 punch PWB wires into the con- 16.Open the upper front cover (28) and insert 17.Attach the label (I) in the location shown in
nectors (27) on the DF main PWB (26). the waste hole punch box (G). the figure.
15.Replace the upper rear cover (4) and small 18.Close the upper front cover (28).
rear cover (2).
14.Raccorder les 2 câbles de la PWB de la per- 16.Ouvrir le couvercle supérieur avant (28) et 17.Apposer l'étiquette (l) à l'endroit indiqué sur
foratrice aux connecteurs (27) de la PWB insérer le bac de récupération de la perfora- la figure.
principale du DF (26). trice (G). 18.Fermer le couvercle supérieur avant (28).
15.Reposer le couvercle supérieur arrière (4) et
le petit couvercle arrière (2).
14.Enchufe los 2 cables del PWB de per- 16.Abra la cubierta delantera superior (28) e 17.Fije la etiqueta (I) en la ubicación como se
foración a los conectores (27) del PWB prin- inserte la caja para desechos de la per- indica en el gráfico.
cipal del DF (26). foración (G). 18.Cierre la cubierta delantera superior (28).
15.Vuelva a colocar la cubierta trasera superior
(4) y la cubierta trasera pequeña (2).
14.Die 2 Kabel der Locher-PWB an die Steck- 16.Die obere vordere Abdeckung (28) öffnen 17.Den Aufkleber (I) an der abgebildeten Stelle
verbinder (27) der DF-Haupt-PWB (26) und den Lochungsabfallbehälter (G) einset- anbringen.
anschließen. zen. 18.Die obere vordere Abdeckung (28)
15.Die obere hintere Abdeckung (4) und die kle- schließen.
ine hintere Abdeckung (2) wieder einsetzen.
14.Collegare i 2 cavi della scheda a circuiti 16.Aprire il pannello superiore anteriore (28) ed 17.Applicare l' etichetta (I) nella posizione
stampati di perforazione nei connettori (27) inserire lo scarto perforazione (G). mostrata nella figura.
sulla scheda principale PWB (26) della DF. 18.Chiudere il pannello superiore anteriore (28).
15.Ricollocare il pannello superiore posteriore
(4) e il pannello posteriore piccolo (2).
14.将打孔电路板的 2 根电线与 DF 主电路板 16.打开前上部盖板 (28)，插入打孔纸屑盒 (G)。 17.在图示位置粘贴标签 (I)。

(26) 的接插件 (27) 连接。 18.关闭前上部盖板 (28)。
15.按原样安装后上部盖板 (4) 与后部小盖板
(2)。
14.펀치기판의 전선 2 선을 DF 주 회로기판 16.앞 상커버 (28) 를 열고 펀치폐기박스 (G) 를 17.라벨 (I) 을 그림의 위치에 붙입니다 .
(26) 의 커넥터 (27) 에 접속합니다 . 삽입합니다 . 18.앞 상커버 (28) 를 닫습니다 .
15.뒷 상커버 (4) 와 후 소커버 (2) 를 원래대로
부착합니다 .
14.パンチ基板の電線 2 本を DF 主回路基板 16.前上カバー(28) を開き、

パンチくずボック 17.ラベル (I) を図の位置に貼り付ける。
(26) のコネクター(27) に接続する。ス (G) を挿入する。 18.前上カバー(28) を閉じる。
15.後上カバー(4) と後小カバー(2) を元通り取
り付ける。
8
32
33 34
31 34
30
29
F
F
Installing the punch PWB and waste hole punch box (DF-790) 13.Plug the 6 hole punch unit wires into the con-
11.Fit the 2 hooks (29) in the punch PWB (F) into the cut (30) in the document finisher. At the same nectors (34) on the punch PWB (F).
time, insert the projection (32) on the document finisher into the hole (31) in the punch PWB (F).
12.Using the screw (H), tighten the hole punch unit ground wire (33) and the punch PWB (F)
together.
Installation de la PWB de la perforatrice et du bac de récupération de la perforatrice (DF-790). 13.Raccorder les 6 câbles de la perforatrice aux
11.Insérer les 2 crochets (29) de la PWB de la perforatrice (F) dans la découpe (30) du retoucheur connecteurs (34) de la PWB de la perfora-
de document. Insérer en même temps la saillie (32) du retoucheur de document dans le trou (31) trice (F).
de la PWB de la perforatrice (F).
12.Fixer le câble de terre de la perforatrice (33) à la PWB de la perforatrice (F) à l'aide d'une vis (H).
Instalación del PWB de perforación y la caja para desechos de la perforación (DF-790) 13.Enchufe los 6 cables de la perforadora a los
11.Coloque los 2 ganchos (29) del PWB de perforación (F) en el corte (30) del finalizador de docu- conectores (34) del PWB de perforación (F).
mentos. Al mismo tiempo, inserte el resalto (32) del finalizador de documentos en el orificio (31)
del PWB de perforación (F).
12.Usando el tornillo (H), apriete juntos el cable de conexión a tierra de la perforadora (33) y el PWB
de perforación (F).
Installation der Locher-PWB und des Lochungsabfallbehälters (DF-790) 13.Die 6 Kabel der Lochereinheit an die Steck-
11.Die 2 Haken (29) in der Locher-PWB (F) in die Aussparung (30) am Dokument-Finisher einset- verbinder (34) der Locher-PWB (F)
zen. Dabei auch den Vorsprung (32) am Dokument-Finisher in die Öffnung (31) auf der Locher- anschließen.
PWB (F) einsetzen.
12.Mit der Schraube (H) das Massekabel (33) der Lochereinheit an der Locher-PWB (F) festziehen.
Installazione della scheda a circuiti stampati di perforazione e dello scarto perforazione (DF-790) 13.Collegare i 6 cavi dell'unità di perforazione
11.Inserire i 2 ganci (29) della scheda a circuiti stampati di perforazione (F) nell'intaglio (30) della nei connettori (34) sulla scheda a circuiti
finitrice di documenti. Contemporaneamente, inserire la sporgenza (32) sulla finitrice di docu- stampati di perforazione (F).
menti nel foro (31) della scheda a circuiti stampati di perforazione (F).
12.Utilizzando la vite (H), stringere insieme il cavo di terra (33) dell'unità di perforazione e la scheda
a circuiti stampati di perforazione (F).
安装电路板与打孔纸屑盒（DF-790 时） 13.将打孔单元的 6 根电线与打孔电路板 (F) 的

11.将打孔电路板 (F) 的 2 个卡扣 (29) 挂在装订器的缺口 (30) 上。同时，将打孔电路板 (F) 的孔接插件 (34) 相连接。
(31) 卡入装订器的突出部 (32)。
12.使用 1 颗螺丝 (H) 将打孔单元的接地线 (33) 与打孔电路板 (F) 一起固定。
기판과 펀치폐기박스의 부착（DF-790 의 경우） 13.펀치유니트의 전선 6 선을 펀치기판 (F) 커넥

11.펀치기판 (F) 의 후크 (29) 2 곳을 문서 피니셔의 구멍 (30) 에 겁니다 . 동시에 펀치기판 (F) 구멍 터 (34) 에 접속합니다 .
(31) 을 문서 피니셔의 돌기 (32) 에 넣습니다 .
12.나사 (H) 1 개로 펀치유니트의 접지선 (33) 과 펀치기판 (F) 을 함게 조입니다 .
基板とパンチくずボックスの取り付け（DF-790 の場合） 13.パンチユニットの電線 6 本を、パンチ基板

11.パンチ基板 (F) のフック (29)2 箇所をドキュメントフィニッシャーの切り欠き (30) に引っ掛け (F) のコネクター(34) に接続する。
る。同時に、パンチ基板 (F) の穴 (31) をドキュメントフィニッシャーの突起 (32) に入れる。
12.ビス (H)1 本で、
パンチユニットのアース線 (33) とパンチ基板 (F) を共締めする。
9
36
37
35 G I
14.Plug the 2 punch PWB wires into the con- 16.Open the upper front cover (37) and insert 17.Attach the label (I) in the location shown in
nectors (36) on the DF main PWB (35). the waste hole punch box (G). the figure.
15.Replace the upper rear cover (8) and small 18.Close the upper front cover (37).
rear cover (6).
14.Raccorder les 2 câbles de la PWB de la per- 16.Ouvrir le couvercle supérieur avant (37) et 17.Apposer l'étiquette (l) à l'endroit indiqué sur
foratrice aux connecteurs (36) de la PWB insérer le bac de récupération de la perfora- la figure.
principale du DF (35). trice (G). 18.Fermer le couvercle supérieur avant (37).
15.Reposer le couvercle supérieur arrière (8) et
le petit couvercle arrière (6).
14.Enchufe los 2 cables del PWB de per- 16.Abra la cubierta delantera superior (37) e 17.Fije la etiqueta (I) en la ubicación como se
foración a los conectores (36) del PWB prin- inserte la caja para desechos de la per- indica en el gráfico.
cipal del DF (35). foración (G). 18.Cierre la cubierta delantera superior (37).
15.Vuelva a colocar la cubierta trasera superior
(8) y la cubierta trasera pequeña (6).
14.Die 2 Kabel der Locher-PWB an die Steck- 16.Die obere vordere Abdeckung (37) öffnen 17.Den Aufkleber (I) an der abgebildeten Stelle
verbinder (36) der DF-Haupt-PWB (35) und den Lochungsabfallbehälter (G) einset- anbringen.
anschließen. zen. 18.Die obere vordere Abdeckung (37) schlie-
15.Die obere hintere Abdeckung (8) und die kle- ßen.
ine hintere Abdeckung (6) wieder einsetzen.
14.Collegare i 2 cavi della scheda a circuiti 16.Aprire il pannello superiore anteriore (37) ed 17.Applicare l' etichetta (I) nella posizione
stampati di perforazione nei connettori (36) inserire lo scarto perforazione (G). mostrata nella figura.
sulla scheda principale PWB (35) della DF. 18.Chiudere il pannello superiore anteriore (37).
15.Ricollocare il pannello superiore posteriore
(8) e il pannello posteriore piccolo (6).
14.将打孔电路板的 2 根电线与 DF 主电路板 16.打开前上部盖板 (37)，插入打孔纸屑盒 (G)。 17.在图示位置粘贴标签 (I)。

(35) 的接插件 (36) 连接。 18.关闭前上部盖板 (37)。
15.按原样安装后上部盖板 (8) 与后部小盖板
(6)。
14.펀치기판의 전선 2 선을 DF 주 회로기판 16.앞 상커버 (37) 를 열고 펀치폐기박스 (G) 를 17.라벨 (I) 을 그림의 위치에 붙입니다 .
(35) 의 커넥터 (36) 에 접속합니다 . 삽입합니다 . 18.앞 상커버 (37) 를 닫습니다 .
15.뒷 상커버 (8) 와 후 소커버 (6) 를 원래대로
부착합니다 .
14.パンチ基板の電線 2 本を DF 主回路基板 16.前上カバー(37) を開き、

パンチくずボック 17.ラベル (I) を図の位置に貼り付ける。
(35) のコネクター(36) に接続する。ス (G) を挿入する。 18.前上カバー(37) を閉じる。
15.後上カバー(8) と後小カバー(6) を元通り取
り付ける。
10
a b
[Adjusting the hole punch position] Adjusting the hole punch entry registration
1.Connect the MFP power plug to the wall out- 1.Enter the maintenance mode U246, select Finisher and Punch Regist.
let and turn the MFP main power switch on. 2.Adjust the values.
2.Make a test copy in punch mode. When the paper fed in skewed copy example (a): Increase the setting value.
3.If any off-centering is observed, follow the When the paper crimped copy example (b): Decrease the setting value.
procedure below to adjust the hole position. 3.Press the Start key to confirm the setting value.
[Réglage de la position des perforations] Réglage de l'enregistrement de l'entrée des perforations

1. Insérer la fiche d’alimentation du MFP dans la prise 1.Passer en mode maintenance U246, sélectionner Finisher et Punch Regist.
murale et mettre l’interrupteur principal du MFP 2.Régler les valeurs.
sous tension.
2. Effectuer une copie d'essai en mode perforation. Si le papier est alimenté de travers exemple de copie (a): Augmentez la valeur de réglage.
3. Si les perforations sont décentrées, suivre la Si le papier est froissé exemple de copie (b): Diminuez la valeur de réglage.
procédure ci-dessous pour ajuster la position de 3.Appuyer sur la touche de Start pour confirmer la valeur de réglage.
perforation.
[Ajuste de la posición de perforación] Ajuste del registro de entrada de perforación

1. Conecte el enchufe del MFP en el receptáculo de 1.Entre en el modo de mantenimiento U246, seleccione Finisher y Punch Regist.
pared y encienda el interruptor principal del MFP. 2.Ajuste los valores.
2. Haga una copia de prueba en el modo de per- Cuando el papel alimentado está torcido copia de muestra (a): Aumente el valor de configuración.
foración. Cuando el papel se dobló copia de muestra (b): Reduzca el valor de configuración.
3. Si observa descentrado, siga el procedimiento de 3.Pulse la tecla de Start para confirmar el valor de configuración.
abajo para ajustar la posición del agujero.
[Einstellen der Lochungsposition] Einstellen der Lochungsregistrierung

1. Stecken Sie den Netzstecker des MFP in die 1.Schalten Sie in den Wartungsmodus U246, wählen Sie Finisher und Punch Regist.
Wandsteckdose und schalten Sie den MFP am 2.Die Werte einstellen.
Hauptschalter ein. Wenn Papier verkantet eingezogen wird Kopiebeispiel (a): Den Einstellwert erhöhen.
2. Eine Testkopie im Lochungsmodus erstellen. Wenn Papier verknittert wird Kopiebeispiel (b): Den Einstellwert verringern.
3. Falls eine außermittige Lochung erfolgte, ist die 3.Den Einstellwert durch Drücken der Start-Taste bestätigen.
Lochungsposition wie folgend nachzustellen.
[Regolazione di posizione dei fori di perforazione] Regolazione del registro del foro di perforazione
1. Collegare la spina del cavo di alimentazione 1.Entrare in modalità manutenzione U246, selezionare Finisher e Punch Regist.
dell’MFP alla presa a muro della rete elettrica e 2.Regolare i valori.
accendere l’interruttore principale di alimentazione.
Quando l'alimentazione della carta risulta obliqua esempio di copia (a): Aumentare il valore
2. Eseguire una copia di prova in modalità di perfora-
zione. dell'impostazione.
3. Nel caso in cui non lo siano, eseguire la procedura Quando la carta risulta increspata esempio di copia (b): Diminuire il valore dell'impostazione.
indicata qui di seguito per regolarne la posizione. 3.Premere il tasto di Start per confermare il valore dell'impostazione.
［打孔位置的调节］打孔装入定位调节
1.将 MFP 主机上的电源插头插入电源插座中， 1.设置维护模式 U246，选择 Finisher、Punch Regist。
打开主电源开关。 2.调整设定值。
2.在打孔模式下进行测试复印。纸张斜向搬运时的复印样本 (a)：调高设定值。
3.打孔位置有偏差时，按以下步骤进行调节。纸张作 Z 字折时的复印样本 (b)：调低设定值。
［펀치위치의 조정］ 펀치반입 레지스트 조정

1.MFP 본체 전원플러그를 콘센트에 꽂고 주 1.메인터넌스 모드 U246 를 세트하고 Finisher, Punch Regist 를 선택합니다 .
전원 스위치를 ON 으로 합니다 . 2.설정치를 조정합니다 .
2.펀치모드에서 시험복사를 합니다 . 용지가 경사로 반송되는 경우의 복사샘플 (a)：설정치를 높입니다 .
3.펀치위치가 벗어난 경우에는 다음 순서로 조 용지가 Z 꺾임이 있는 경의 복사샘플 (b)：설정치를 내립니다 .
정합니다 . 3.시작키를 누르고 설정치를 확인합니다 .
［パンチ位置の調整］パンチ搬入レジスト調整
1.MFP 本体の電源プラグをコンセントに差し 1.メンテナンスモード U246 をセットし、Finisher、
Punch Regist を選択する。
込み、主電源スイッチを ON にする。 2.設定値を調整する。
2.パンチモードでテストコピーを行う。用紙が斜めに搬送される場合コピーサンプル (a)：設定値を上げる。
3.パンチ位置がずれていた場合、次の手順で調用紙が Z 折れする場合コピーサンプル (b)：設定値を下げる。
整を行う。 3.スタートキーを押し、設定値を確定する。
11
c
Adjusting the hole punch position feed 3.Press the Start key to confirm the setting value.
1.Enter the maintenance mode U246, select Finisher and Punch Feed. <Reference value (c)>
2.Adjust the values. Metric specification: 13 mm; Inch specification: 9.5 mm
If the punch hole position is closer to the edge than the reference value
(c): Increase the setting value.
If the punch hole position is further from the edge than the reference
value (c): Decrease the setting value.
Réglage de la position du point de perforation 3.Appuyer sur la touche de Start pour confirmer la valeur de réglage.
1. Passer en mode maintenance U246, sélectionner Finisher et Punch Feed. <Valeur de référence (c)>
2. Régler les valeurs. Spécifications métriques: 13 mm; Spécifications en pouces: 9,5 mm
Si la perforation est plus proche du bord de la feuille que défini par la valeur de
référence (c): Augmentez la valeur de réglage.
Si la perforation est plus loin du bord de la feuille que défini par la valeur de
référence (c): Diminuez la valeur de réglage.
Ajuste de la alimentación de la posición de perforación 3.Pulse la tecla de Start para confirmar el valor de configuración.
1. Entre en el modo de mantenimiento U246, seleccione Finisher y Punch Feed. <Valor de referencia (c)>
2. Ajuste los valores. Sistema métrico: 13 mm; en pulgadas: 9,5 mm
Si la posición de perforación está más cerca del borde que el valor de referencia
(c): Aumente el valor de configuración.
Si la posición de perforación está más alejada del borde que el valor de referen-
cia (c): Reduzca el valor de configuración.
Einstellen des Transports der Lochungsposition 3.Den Einstellwert durch Drücken der Start-Taste bestätigen.
1. Schalten Sie in den Wartungsmodus U246, wählen Sie Finisher und Punch Feed. <Bezugswert (c)>
2. Die Werte einstellen. Metrischer Abstand: 13 mm; Abstand in Zoll: 9,5 mm
Falls die Lochungsposition näher an der Kante liegt als der Bezugswert (c)
erlaubt: Den Einstellwert erhöhen.
Falls die Lochungsposition ferner von der Kante liegt als der Bezugswert (c)
erlaubt: Den Einstellwert verringern.
Regolazione spostamento di posizione dei fori di perforazione 3.Premere il tasto di Start per confermare il valore dell'impostazione.
1. Entrare in modalità manutenzione U246, selezionare Finisher e Punch Feed. <Valore di riferimento (c)>
2. Regolare i valori. Specificazione in unità metrica: 13 mm; Specificazione in pollici: 9,5
Se la posizione dei fori di perforazione è più vicina al bordo rispetto al valore di mm
riferimento (c): Aumentare il valore dell'impostazione.
Se la posizione dei fori di perforazione è più lontana dal bordo rispetto al valore di
riferimento (c): Diminuire il valore dell'impostazione.
打孔位置搬运调节 3.按 Start 键，以确定设定值。

1.设置维护模式 U246，选择 Finisher、Punch Feed。＜基准值 (c) ＞
2.调整设定值。公制规格：13mm、英制规格：9.5mm
打孔位置比基准值 (c) 短时：调高设定值。
打孔位置比基准值 (c) 长时：调低设定值。
펀치위치 반송조정 3.시작키를 누르고 설정치를 확인합니다 .

1.메인터넌스 모드 U246 를 세트하고 Finisher, Punch Feed 를 선택합 ＜기준치 (c) ＞
니다 . 센치사양：13mm, 인치사양：9.5mm
펀치구멍의 위치가 기준치 (c) 보다 짧은 경우：설정치를 높입니다 .
펀치구멍의 위치가 기준치 (c) 보다 긴 경우：설정치를 내립니다 .
パンチ位置搬送調整 3.スタートキーを押し、設定値を確定する。

Punch Feed を選択す＜基準値 (c) ＞
る。センチ仕様：13mm、インチ仕様：9.5mm
パンチ穴の位置が基準値 (c) より短い場合：設定値を上げる。
パンチ穴の位置が基準値 (c) より長い場合：設定値を下げる。
12
e f
d
f
Centering the hole punch position 3.Press the Start key to confirm the setting value.
1.Enter the maintenance mode U246, select Finisher and Punch Width. <Reference value>
2.Adjust the values. Metric specification: d = 80 mm ± 0.5, e = 40 mm ± 2
If the punch hole is too close to the front of the machine: Decrease the Inch specification: d = 2.75 inch ± 0.5, e = 1.375 inch ± 2,
setting value. f = 4.25 inch ± 0.5
If the punch hole is too close to the rear of the machine: Increase the
setting value.
Centrage de la position de perforation 3.Appuyer sur la touche de Start pour confirmer la valeur de réglage.
1. Passer en mode maintenance U246, sélectionner Finisher et Punch Width. <Valeur de référence>
2. Régler les valeurs. Spécifications métriques: d = 80 mm ± 0,5, e = 40 mm ± 2
Si la perforation est trop proche de l'avant de la machine: Diminuez la valeur de Spécifications en pouces: d = 2,75 pouces ± 0,5, e = 1,375 pouces ± 2,
réglage. f = 4.25 pouces ± 0,5
Si la perforation est trop proche de l'arrière de la machine: Augmentez la valeur
de réglage.
Centrado de la posición de perforación 3.Pulse la tecla de Start para confirmar el valor de configuración.
1. Entre en el modo de mantenimiento U246, seleccione Finisher y Punch Width. <Valor de referencia>
2. Ajuste los valores. Sistema métrico: d = 80 mm ± 0,5, e = 40 mm ± 2
Si la perforación se encuentra demasiado cerca del frente de la máquina: En pulgadas: d = 2,75 pulgada ± 0,5, e = 1,375 pulgada ± 2,
Reduzca el valor de configuración. f = 4.25 ± 0,5 pulgada
Si la perforación se encuentra demasiado cerca de la parte trasera de la
máquina: Aumente el valor de configuración.
Zentrieren der Stanzlochposition 3.Den Einstellwert durch Drücken der Start-Taste bestätigen.
1. Schalten Sie in den Wartungsmodus U246, wählen Sie Finisher und Punch <Bezugswert>
Width. Metrischer Abstand: d = 80 mm ± 0,5; e = 40 mm ± 2
2. Die Werte einstellen. Abstand in Zoll: d = 2,75 Zoll ± 0,5, e = 1,375 Zoll ± 2,
Falls die Lochung zu nah an der Gerätefront liegt: Den Einstellwert verringern. f = 4.25 Zoll ± 0,5
Falls die Lochung zu weit weg von der Gerätefront liegt: Den Einstellwert
erhöhen.
Centratura della posizione dei fori di perforazione 3.Premere il tasto di Start per confermare il valore dell'impostazione.
1. Entrare in modalità manutenzione U246, selezionare Finisher e Punch Width. <Valore di riferimento>
2. Regolare i valori. Specificazione in unità metrica: d = 80 mm ± 0,5, e = 40 mm ± 2
Se la posizione dei fori di perforazione è troppo vicina alla parte anteriore della Specificazione in pollici: d = 2,75 pollici ± 0.5, e = 1,375 pollici ± 2,
macchina: Diminuire il valore dell'impostazione. f = 4.25 pollici ± 0.5
Se la posizione dei fori di perforazione è troppo vicina alla parte posteriore della
macchina: Aumentare il valore dell'impostazione.
打孔位置中心调节 3.按 Start 键，以确定设定值。

1.设置维护模式 U246，选择 Finisher、Punch Width。＜基准值＞
2.调整设定值。公制规格：d=80mm±0.5、e=40mm±2
打孔位置向机器前部偏移时：调低设定值。英制规格：d=2.75inch±0.5、e=1.375inch±2、f=4.25inch±0.5
打孔位置向机器后部偏移时：调高设定值。
펀치위치 센터조정 3.시작키를 누르고 설정치를 확인합니다 .

1.메인터넌스 모드 U246 를 세트하고 Finisher, Punch Width 를 선택합 ＜기준치＞
니다 . 센치 사양：d=80mm±0.5, e=40mm±2
2.설정치를 조정합니다 . 인치사양：d=2.75inch±0.5, e=1.375inch±2, f=4.25inch±0.5
펀치구멍이 기기 앞측으로 벗어난 경우：설정치를 내립니다 .
펀치구멍의 위치가 기기 뒷측으로 벗어난 경우：설정치를 높입니다 .
パンチ位置センター調整 3.スタートキーを押し、設定値を確定する。

Punch Width を選択す＜基準値＞
る。センチ仕様：d=80mm±0.5、e=40mm±2
2.設定値を調整する。インチ仕様：d=2.75inch±0.5、e=1.375inch±2、f=4.25inch±0.5
パンチ穴の位置が機械前側にずれている場合：設定値を下げる。
パンチ穴の位置が機械後側にずれている場合：設定値を上げる。
13
[Swedish specification]
1.When using the hole punch unit of Swedish specification, enter the maintenance mode U234 and select Sweden.
[Spécifications suédoises]
1.Lors de l’utilisation de la perforatrice avec les spécifications suédoises, entrer le mode d’entretien U234 et sélectionner Sweden.
[Especificaciones suecas]
1.Cuando se utilice la perforadora con especificaciones suecas, entre en el modo de mantenimiento U234 y seleccione Sweden.
[Schwedische Spezifikation]
1.Wenn die Lochereinheit der schwedischen Spezifikation benutzt wird, ist der Wartungsmodus U234 einzugeben und dann Sweden anzuwählen.
[Specificazione svedese]
1.Quando si utilizza un’unità di perforazione di specificazione svedese, entrare nella modalità di manutenzione U234 e selezionare Sweden.
[ 瑞典规格 ]
1.使用瑞典规格的打孔单元时，输入维修模式 U234 并选择 Sweden（瑞典公制）。
[ 스웨덴 사양 ]
1.펀치 유니트가 스웨덴 사양인 경우 , 메인터넌스 모드 U234 를 세트하고 Sweden 을 선택합니다 .
[ スウェーデン仕様 ]
1.パンチユニットがスウェーデン仕様の場合、メンテナンスモード U234 をセットし、Sweden を選択する。
14
NOTICE
This accessory is for use only with the following Applicant's Listed Machine.
Refer to the supplied guide to install the accessory in the field.
Machine: DF-770, DF-790
AVIS
Cet accessoire est utilisable uniquement avec le copieur figurant dans la liste du demandeur suivant.
Se reporter au guide fourni pour installer l'accessoire dans le champ.
Modèle: DF-770, DF-790
AVISO
Este accesorio es sólo para usar en las siguientes fotocopiadoras de la lista de solicitantes.
Consulte las instrucciones para la instalación de accesorios en el lugar del cliente.
Modelo: DF-770, DF-790
HINWEIS
Dieses Zubehör ist nur für den Einsatz mit der folgenden Antragstellerlisten-Kopiermaschine vorgesehen.
Installieren Sie das Zubehör gemäß der mitgelieferten Anleitung im Feld.
Modell: DF-770, DF-790
NOTIFICA
Questo accessorio deve essere usato solo con le seguenti fotocopiatrici nella lista dell’applicante.
Consultare la guida fornita in dotazione per il montaggio in campo dell’accessorio.
Modello: DF-770, DF-790
注意
本产品适用于以下选购件。
安装时，请参照附带的说明书。
式样 :DF-770,DF-790
주의
본 제품은 이하의 기종에 적용됩니다 .
설치할 때에는 동봉된 안내문을 참조해 주십시오 .
기종：DF-770,DF-790
注意
本製品は、以下の機種に適用します。
設置する際は、同梱の手順書を参照してください。
機種：DF-770, DF-790
15
FAX System
English
To install the FAX circuit board, see page 1. To install the FAX circuit board as Dual FAX, see page 17.
References to medium-speed MFPs in this document denote 30/30, 35/35, 45/45 and 55/50 ppm color machines, and 35, 45 and 55 ppm monochrome machines.
References to high-speed MFPs in this document denote 65/65 and 75/70 ppm color machines, and 65 and 80 ppm monochrome machines.
(The generic procedure figures in this document show medium-speed MFPs.)
If the finisher is already installed, remove the finisher before installing FAX System(V).
Français
Pour installer la carte à circuits FAX, se reporter à la page 1. Pour installer la carte à circuits FAX comme FAX double, se reporter à la page 17.
Dans le présent document, les références aux MFP à vitesse moyenne renvoient aux machines couleurs 30/30, 35/35, 45/45 et 55/50 ppm et aux machines mono-
chromes 35, 45 et 55 ppm.
Dans le présent document, les références aux MFP à grande vitesse renvoient aux machines couleurs 65/65 et 75/70 ppm et aux machines monochromes 65 et 80
ppm. (Dans ce document, les chiffres des processus génériques renvoient aux MPF à vitesse moyenne.)
Si le retoucheur est déjà en place, le déposer avant de monter le FAX System(V).
Español
Para instalar la tarjeta de circuitos de FAX, vea la página 1. Para instalar la tarjeta de circuitos de FAX en el FAX dual, vea la página 17.
Las referencias a las MFP de velocidad media de este documento corresponden a las máquinas a color de 30/30, 35/35, 45/45 y 55/50 ppm y a las máquinas
monocromáticas de 35, 45 y 55 ppm.
Las referencias a las MFP de alta velocidad de este documento corresponden a las máquinas a color de 65/65 y 75/70 ppm y a las máquinas monocromáticas de
65 y 80 ppm. (Las ilustraciones de procedimientos genéricos de este documento muestran las MFP de velocidad media.)
Si el finalizador ya se encuentra instalado, desmóntelo antes de instalar el FAX System(V).
Deutsch
Angaben zur Installation der FAX-Leiterplatte finden Sie auf Seite 1. Angaben zur Installation der FAX-Leiterplatte als Dual FAX finden Sie auf Seite 17.
Angaben für MFP der mittleren Leistungsklasse in dieser Anleitung gelten für die 30/30, 35/35, 45/45 und 55/50 ppm Vollfarbenkopierer sowie für die 35, 45 und 55
ppm Monochrommaschinen.
Angaben für MFP der Hochleistungsklasse in dieser Anleitung gelten für die 65/65 und 75/70 ppm Vollfarbenkopierer sowie für die 65 und 80 ppm Monochrommas-
chinen. (Die Abbildungen der allgemeinen Prozeduren zeigen MFP der mittleren Leistungsklasse.)
Falls der Finisher schon installiert ist, müssen Sie ihn ausbauen, bevor Sie das FAX System(V) installieren.
Italiano
Per installare la scheda a circuiti FAX, vedere pagina 1. Per installare la scheda a circuiti FAX come Dual FAX, vedere pagina 17.
I riferimenti per le MFP a velocità media riportati in questo documento indicano le macchine a colori 30/30, 35/35, 45/45 e 55/50 ppm, e le macchine monocro-
matiche 35, 45 e 55 ppm.
I riferimenti per le MFP a velocità alta riportati in questo documento indicano le macchine a colori 65/65 e 75/70 ppm, e le macchine monocromatiche 65 e 80 ppm.
(Le figure della procedura generica riportate in questo documento mostrano le MFP a velocitò media.)
Se la finitrice è già installata, rimuovere la finitrice prima di installare il FAX System(V).
简体中文
安装传真组件时 … 从第 1 页开始　安装多插口组件时 … 从第 17 页开始
本文中的中速 MFP 代表彩色 30/30 页机型、35/35 页机型、45/45 页机型、55/50 页机型、黑白 35 页机型、45 页机型、55 页机型。
本文中的高速 MFP 代表彩色 65/65 页机型、75/70 页机型、黑白 65 页机型、80 页机型。（本文中的通用步骤的插图为中速 MFP。）
已安装装订器时，必须先拆下装订器再安装 FAX System(V)。
한국어
팩스 시스템을 설치하는 경우 …1 페이지에서 시작합니다 .
멀티포트를 설치하는 경우 …17 페이지에서 시작합니다 .
본문 중 중속 MFP 는 컬러 30/30 매기 , 35/35 매기 , 45/45 매기 , 55/50 매기 , 흑백 35 매기 , 45 매기 , 55 매기를 나타냅니다 .
본문 중 고속 MFP 는 컬러 65/65 매기 , 75/70 매기 , 흑백 65 매기 , 80 매기를 나타냅니다 .（본문 중 공통 순서 일러스트는 중속 MFP 로 한다 .）
피니셔가 이미 장착되어 있는 경우에는 피니셔를 제거하고 FAX System(V) 를 설치할 것 .
日本語
ファクスシステムを設置する場合 …1 ページから始める。　マルチポートを設置する場合 …17 ページから始める。
本文中の中速 MFP はカラー機の 30/30 枚機、35/35 枚機、45/45 枚機、55/50 枚機、モノクロ機の 35 枚機、45 枚機、55 枚機を表す。
本文中の高速 MFP はカラー機の 65/65 枚機、75/70 枚機、モノクロ機の 65 枚機、 80 枚機を表す。
（本文中の共通手順イラストは中速 MFP とする。）
フィニッシャーがすでに装着されている場合は、フィニッシャーを取り外してから、FAX System(V) を取り付けること。
A
H
E
C
K
I
F
B
J
D G
Supplied parts D. Alphabet label ............................................ 1 J. Memory DIMM (16 MB) ............................. 1
A. FAX circuit board ....................................... 1 E. FAX operation section label ....................... 1
B. Modular connector cable F. FAX key ..................................................... 1 Option
(120 V/Australian model only) G. FAX key cover............................................ 1 K. Memory DIMM (128 MB) ........................... 1
PJJWC0016Z (UL Listed.HUAN HSIN H. PTT label (110V model only) ..................... 1
Type TL:120 V only)1 I. Approval label When installing the Dual FAX, (A), (B), (C) are
C. Terminal seal ............................................. 1 (Australian/New Zealand models only) ...... 2 required.
Pièces fournies E. Etiquette de la section de fonctionnement Option

A. Carte à circuits FAX ................................... 1 FAX ........................................................... 1 K. Mémoire DIMM (128 MB) .......................... 1
B. Câble du connecteur modulaire (modèles F. Touche FAX ............................................... 1
pour l’Australie/120 V seulement).............. 1 G. Couvercle de touche FAX .......................... 1 (H) et (I) ne sont pas fournis.
C. Joint de borne............................................ 1 J. Mémoire DIMM (16 MB) ............................ 1 L'installation du Dual FAX requiert l'installation
D. Etiquette de l’alphabet ............................... 1 des pièces (A), (B), (C).
Partes suministradas E. Etiqueta de la sección de funcionamiento Opción

A. Tarjeta de circuitos de fax .......................... 1 de FAX ...................................................... 1 K. Memoria DIMM (128 MB) .......................... 1
B. Cable conector modular (sólo para F. Tecla de FAX.............................................. 1
modelos de 120 V/Australianos)................ 1 G. Cubierta de la tecla de FAX ....................... 1 (H) y (I) no se suministran.
C. Sello del terminal ....................................... 1 J. Memoria DIMM (16 MB) ............................ 1 Cuando instale el fax Dual se necesitan (A), (B),
D. Etiqueta de alfabeto................................... 1 (C).
Gelieferte Teile J. Speicher-DIMM (16 MB) ............................ 1 (B), (H) und (I) liegen nicht bei.
A. FAX-Leiterplatte......................................... 1 Für die Installation von Dual FAX sind (A), (C)
C. Verschlusskappe ....................................... 1 Option erforderlich.
D. Alphabetaufkleber...................................... 1 K. Speicher-DIMM (128 MB) .......................... 1
E. Aufkleber für FAX-Bedienungsabschnitt.... 1
F. FAX-Taste .................................................. 1
G. FAX-Tastenabdeckung .............................. 1
Parti di fornitura G. Copertura tasto FAX .................................. 1 (B), (H) e (I) non sono in dotazione.
A. Scheda a circuiti FAX ................................ 1 J. Memoria DIMM (16 MB) ............................ 1 Quando si installa il Dual FAX, sono necessari
C. Guarnizione terminale ............................... 1 (A), (C).
D. Etichetta alfabetica .................................... 1 Opzioni
E. Etichetta della sezione funzionamento K. Memoria DIMM (128 MB) .......................... 1
FAX............................................................ 1
F. Tasto FAX .................................................. 1
附属品 F. FAX 键 ................................1 选购件

A. 传真电路板........................... 1 G. FAX 键盖板 ............................1 K. 内存模组 DIMM (128MB) .................1
B. 电话线............................... 1 H. 规格标签 .............................1
C. 端子密封............................. 1 J. 内存模组 DIMM (16MB) ..................1 (I) 并非附属品。
D. 英文字母标签......................... 1 安装多插口组件时，需要 (A)、(B)、(C)。
E. 传真操作部标签....................... 1
동봉품 G. FAX 키커버 ........................................ 1 （B）（H）

（I）는 동봉되어 있지 않습니다 .
A. FAX 기판 ........................................... 1 J. 메모리 DIMM（16MB）......................... 1 멀티포트 설치 시에는 (A),(C) 가 필요합니다 .
C. 단자씰............................................... 1
D. 알파벳 라벨........................................ 1 옵션
E. FAX 조작부 라벨 ................................. 1 K. 메로리 DIMM（128MB）........................ 1
F. FAX 키 .............................................. 1
同梱品 J. メモリーDIMM（16MB）...................1 (D)(H)(I) は、

同梱されていない。
A. FAX 基板 ............................. 1 マルチポート設置時は (A),(B),(C), が必要と
B. モジュラーコード..................... 1 オプションなる。
C. 端子シール........................... 1 K. メモリーDIMM（128MB）..................1
E. FAX 操作部ラベル ..................... 1
F. FAX キー ............................. 1
G. FAX キーカバー ....................... 1
1
3
2
1
J K
Precautions Procedure 2.Install the memory DIMM (J) or the optional

Be sure to remove any tape and/or cushioning Installing the memory DIMM memory DIMM (K) into the memory slot (3)
material from supplied parts. 1.Remove 2 screws (1), and then remove the on the lower level (FLS).
Be sure to turn the MFP switch OFF and unplug cover (2). Install it with the IC side facing down. Insert it
the MFP from the power supply before installing in the direction of the arrow until it clicks.
the fax system.
Précautions Procédure 2.Installer la mémoire DIMM (J) ou la mémoire

Veillez à retirer les morceaux de bande adhé- Installation de la mémoire DIMM DIMM en option (K) dans la fente mémoire
sive et/ou les matériaux de rembourrage des 1.Déposez les 2 vis (1) puis enlevez le couver- (3) se trouvant au niveau inférieur (FLS).
pièces fournies. cle (2). L'installer avec le côté IC en bas. L'insérer
Veiller à mettre l’interrupteur principal du MFP dans la direction de la flèche jusqu'au clic.
hors tension et à débrancher le MFP de la prise
secteur avant d’installer le système fax.
Precauciones Procedimiento 2.Instale la memoria DIMM (J), o la memoria

Asegúrese de despegar todas las cintas y/o mate- Instalación de la memoria DIMM DIMM opcional (K), en la ranura para memo-
rial amortiguador de las partes suministradas. 1.Quite 2 tornillos (1) y, después, desmonte la ria (3) en el nivel inferior (FLS).
Asegúrese de apagar el MFP colocando el interrup- cubierta (2). Instálelo con el lado IC hacia abajo.Insértela
tor principal a OFF y desenchufe el MFP del sumin- en la dirección que indica la flecha hasta
istro de red eléctrica antes de instalar el sistema de que escuche un clic.
fax.
Vorsichtsmaßnahmen Verfahren 2.Setzen Sie das DIMM-Speichermodul (J)

Entfernen Sie Klebeband und/oder Dämpfungs- Installation der DIMM-Speichermodule oder das optionale DIMM-Speichermodul (K)
material vollständig von den mitgelieferten 1.Entfernen Sie 2 Schrauben (1) und nehmen in die untere Position (FLS) der Speicher-
Teilen. Sie dann die Abdeckung (2) ab. bank (3) ein.
Schalten Sie den Netzschalter des MFP aus Mit der IC-Seite nach unten weisend install-
und trennen Sie den MFP vom Netz, bevor Sie ieren.Schieben Sie das Modul in
das Faxsystem installieren. Pfeilrichtung, bis es hörbar einrastet.
Precauzioni Procedura 2.Installare la memoria DIMM (J) o la memoria

Accertarsi di rimuovere tutti i nastri adesivi e/o il Installazione della memoria DIMM DIMM opzionale (K) nello slot della memoria
materiale di imbottitura dalle parti fornite. 1.Rimuovere 2 viti (1), e quindi rimuovere il (3) al livello inferiore (FLS).
Assicurarsi di aver spento l’interruttore dell’MFP coperchio (2). Installare con il lato IC rivolto verso il
e di aver sfilato la spina dell’MFP dalla presa basso.Inserirla nella direzione della freccia
prima di installare il sistema fax. finché non scatta in posizione.
注意事项安装步骤 2.将内存模组 DIMM (J) 或选购件内存模组

如果附属品上带有固定胶带，缓冲材料时务必揭安装内存模组 DIMM DIMM (K) 安装至下层 (FLS) 的内存插槽 (3)。
下。 1.取下 2 个螺丝 (1)，然后取下盖板 (2)。安装时，将 IC 侧正面朝下。沿箭头方向将其
请务必关闭 MFP 的开关并拔下电源插头再安装传插入到底直至发出喀嗒声。
真组件。
주의사항 설치순서 2.메모리 DIMM（J） 또는 옵션 메모리

동봉품에 고정 테이프 , 완충재가 붙어 있는 경 메모리 DIMM 설치 DIMM(K) 를 하단 (FLS) 의 메모리 슬롯 (3)
우에는 반드시 제거할 것 . 1.나사 (1) 2 개를 제거하고 커버 (2) 를 제거합 에 장착합니다 .
팩스 시스템을 설치하는 경우에는 MFP 본체의 니다 . IC 면을 밑으로 할 것 .
주 전원 스위치를 OFF 로 하고 전원 플러그를 딸칵하고 소리가 날 때까지 화살표 방향으로
뺀 다음 작업을 합니다 . 삽입합니다 .
注意事項取付手順 2.メモリーDIMM（J）または、オプションのメモ

同梱品に固定テープ、緩衝材が付いている場合メモリーDIMM の取り付けリーDIMM(K) を下段 (FLS) のメモリース
は必ず取り外すこと。 1.ビス (1)2 本を外し、カバー(2) を取り外す。ロット (3) に取り付ける。
ファクスシステムを設置する場合は、 MFP 本体の IC 面を下向きに取り付けること。
主電源スイッチを OFF にし、電源プラグを抜いカチッと音がするまで矢印方向に挿入する。
てから作業をおこなう。
2
4
3.Replace the cover (2) using the 2 screws (1). Removing the slot cover 5.Remove 2 screws (6) and then remove the
(medium-speed MFPs) OPT1 slot cover (5).
4.Open the cover (4). * Do not use OPT2.
To install the FAX circuit board as Dual FAX,

see page 17.
3.Reposez le couvercle (2) à l'aide des 2 vis (1). Dépose du couvercle de la fente 5.Déposer les 2 vis (6) puis le couvercle de la
(MFP à vitesse moyenne) fente OPT1 (5).
4.Ouvrir le couvercle (4). * Ne pas utiliser OPT2.
Pour installer la carte à circuits FAX comme

FAX double, se reporter à la page 17.
3.Vuelva a colocar la cubierta (2) utilizando los Desmontaje de la cubierta de la ranura 5.Quite 2 tornillos (6) y, después, quite la cubi-
2 tornillos (1). (MFP de velocidad media) erta de la ranura OPT1 (5).
4.Abra la cubierta (4). * No utilice OPT2.
Para instalar la tarjeta de circuitos de FAX

en el FAX dual, vea la página 17.
3.Bringen Sie die Abdeckung (2) wieder mit Entfernen der Einschubabdeckung 5.2 Schrauben (6) entfernen und dann die
den 2 Schrauben (1) an. (MFP der mittleren Leistungsklasse) Abdeckung (5) des Einschubs OPT1 ent-
4.Die Abdeckung (4) öffnen. fernen.
* OPT2 nicht verrwenden.
Angaben zur Installation der FAX-Leiter-

platte als Dual FAX finden Sie auf Seite 17.
3.Ricollocare il coperchio (2) utilizzando le 2 Rimozione del coperchio vano 5.Rimuovere le 2 viti (6) e quinidi rimuovere il
viti (1). (MFP a velocità media) coperchio (5) del vano OPT1.
4.Aprire il coperchio (4). * Non utilizzare OPT2.
Per installare la scheda a circuiti FAX come

Dual FAX, vedere pagina 17.
3.使用 2 个螺丝 (1) 重新安装盖板 (2)。拆下插槽盖板（中速 MFP 时） 5.拆除 2 颗螺丝 (6)，拆下 OPT1 的插槽盖板
4.打开盖板 (4)。 (5)。
※ 不使用 OPT2。
安装多插口组件时 … 从第 17 页开始
3.나사 (1) 2 개로 커버 (2) 를 원래대로 장착합 슬롯커버 제거（중속 MFP 의 경우） 5.나사 (6) 2 개를 제거하고 OPT1 의 슬롯커버
니다 . 4.커버 (4) 를 엽니다 . (5) 를 제거합니다 .
※OPT2 는 사용하지 말 것 .
멀티포트를 설치하는 경우 …17 페이지에서

시작합니다 .
3.ビス (1)2 本で、

カバー(2) を元通り取り付スロットカバーの取り外し（中速 MFP の場合） 5.ビス (6)2 本を外し、OPT1 のスロットカバー
ける。 4.カバー(4) を開ける。 (5) を取り外す。
※OPT2 は使用しないこと。
マルチポートを設置する場合 …17 ページか

ら始める。
3
4
5
Removing the slot cover (For high-speed 5.Remove 2 screws (6) and then remove the
MFPs and when the finisher is installed) OPT1 slot cover (5).
4.Remove the cover (4). * Do not use OPT2.
To install the FAX circuit board as Dual FAX,

see page 17.
Dépose du couvercle de la fente (Pour les 5.Déposer les 2 vis (6) puis le couvercle de la
MFP à grande vitesse quand le retoucheur fente OPT1 (5).
est installé) * Ne pas utiliser OPT2.
4.Déposer le couvercle (4).
Pour installer la carte à circuits FAX comme
FAX double, se reporter à la page 17.
Desmontaje de la cubierta de la ranura (Para 5.Quite 2 tornillos (6) y, después, quite la cubi-
las MFP de alta velocidad y cuando el final- erta de la ranura OPT1 (5).
izador está instalado) * No utilice OPT2.
4.Quite la cubierta (4).
Para instalar la tarjeta de circuitos de FAX
en el FAX dual, vea la página 17.
Entfernen der Einschubabdeckung (Für MFP 5.2 Schrauben (6) entfernen und dann die
der Hochleistungsklasse und wenn der Fin- Abdeckung (5) des Einschubs OPT1 ent-
isher installiert ist) fernen.
4.Die Abdeckung (4) entfernen. * OPT2 nicht verrwenden.
Angaben zur Installation der FAX-Leiter-

platte als Dual FAX finden Sie auf Seite 17.
Rimozione del coperchio vano (Per MFP a 5.Rimuovere le 2 viti (6) e quinidi rimuovere il
velocità alta e quando la finitrice è installata) coperchio (5) del vano OPT1.
4.Rimuovere il coperchio (4). * Non utilizzare OPT2.
Per installare la scheda a circuiti FAX come

Dual FAX, vedere pagina 17.
拆下插槽盖板 5.拆除 2 颗螺丝 (6)，拆下 OPT1 的插槽盖板

（高速 MFP 且安装装订器时） (5)。
4.拆下盖板 (4)。 ※ 不使用 OPT2。
安装多插口组件时 … 从第 17 页开始
슬롯커버 제거 5.나사 (6) 2 개를 제거하고 OPT1 의 슬롯커버

（고속 MFP 및 피니셔 장착 시의 경우） (5) 를 제거합니다 .
4.커버 (4) 를 제거합니다 . ※OPT2 는 사용하지 말 것 .
멀티포트를 설치하는 경우 …17 페이지에서

시작합니다 .
スロットカバーの取り外し 5.ビス (6)2 本を外し、OPT1 のスロットカバー

（高速 MFP およびフィニッシャー装着時の場合） (5) を取り外す。
4.カバー(4) を取り外す。 ※OPT2 は使用しないこと。
マルチポートを設置する場合 …17 ページか

ら始める。
4
7
A
6
Install the FAX circuit board.

6.Insert the FAX circuit board (A) along the groove in OPT1 and secure the board with two screws
(6) that have been removed in step 5.
Do not directly touch the FAX circuit board (A) terminal. Hold the top and bottom of the FAX circuit
board, or the projection of the board to insert the FAX circuit board (A).
Direct the label (7) on to the FAX circuit board (A) as indicated in the illustration and insert the
board along the groove.
Installer la carte à circuits FAX.

6.Insérer la carte à circuits FAX (A) le long de la rainure dans l’OPT1 et la fixer à l’aide des deux vis
(6) retirées à l’étape 5.
Ne pas toucher directement la borne de la carte à circuits FAX (A). Tenir les parties inférieure et
supérieure de la carte à circuits FAX ou la saillie de la carte pour insérer la carte à circuits FAX
(A).Orienter l'étiquette (7) de la carte à circuits FAX (A) comme illustré et insérer la plaquette le
long de la rainure.
Instale la tarjeta de circuitos de fax.

6. Inserte la tarjeta de circuitos de fax (A) a lo largo de la ranura de OPT1 y asegúrela con los dos tornillos
(6) que ha quitado en el paso 5.
No toque directamente el terminal de la tarjeta de circuitos del fax (A). Sujete las partes superior e infe-
rior de la tarjeta de circuitos de fax o la saliente de la tarjeta para insertar la tarjeta de circuitos de fax
(A).Oriente la etiqueta (7) en la tarjeta de circuitos del FAX (A) como se indica en la ilustración e inserte
la tarjeta a lo largo de la ranura.
Installieren der FAX-Leiterplatte.

6.FAX-Leiterplatte (A) in die Nut des Einbauschachts OPT1 einsetzen und Leiterplatte mit den in
Schritt 5 ausgebauten Schrauben (6) befestigen.
Berühren Sie die Anschlüsse der FAX-Platine (A) nicht mit den Fingern. Die FAX-Leiterplatte (A)
bein Einsetzen oben und unten oder an dem Vorsprung festhalten.
Die FAX-Leiterplatte (A) so in die Nut einsetzen, dass der Aufkleber (7) wie abgebildet zur
Leiterplatte zeigt.
Installare la scheda a circuiti FAX.

6.Inserire la scheda a circuiti FAX (A) lungo l’incavo nell’OPT1 e fissare la scheda con le due viti (6)
rimosse nell’operazione 5.
Non toccare direttamente il terminale della scheda a circuiti FAX (A). Per inserire il circuito FAX
(A), tenere l’estremit superiore e la base della scheda a circuiti FAX, o la sporgenza della scheda
a circuiti FAX. Orientare l'etichetta (7) sulla scheda a circuiti FAX (A) come indicato nell'illustra-
zione e inserire la scheda lungo l'incavo.
安装传真电路板
6.沿着 OPT1 的沟槽插入传真电路板 (A) 并用在步骤 5 中拆下的两颗螺钉 (6) 固定电路板。
请勿直接触摸传真电路板 (A) 端子。
按住传真电路板的顶部和底部，或者按住电路板的突出部将传真电路板 (A) 插入。
将传真电路板 (A) 上的标签 (7) 保持图示中的方向，将电路板沿着沟槽方向插入。
FAX 기판 장착
6.OPT1 구에 붙여 FAX 기판 (A) 를 삽입하고 순서 5 에서 제거한 나사 (6) 2 개로 고정합니다 .
FAX 기판 (A) 의 단자에 직접 닿지 않게 할 것 .
FAX 기판 (A) 을 삽입 시에는 기판의 상하 또는 돌기를 잡을 것 .
FAX 기판 (A) 을 붙여진 라벨 (7) 그림 표기 방향대로 되도록 삽입할 것 .
FAX 基板の取り付け
6.OPT1 の溝に沿って FAX 基板 (A) を挿入し、手順 5 で外したビス (6)2 本で固定する。
FAX 基板 (A) の端子に直接触れないこと。
FAX 基板 (A) の挿入時は基板の上下か突起を持つこと。
FAX 基板 (A) は、貼り付けられているラベル (7) が図に示す方向になるように、挿入すること。
5
B
Connect the MFP to the telephone line. For 100 V/120 V/Australian or Chinese models,
7.Plug the modular connector cable (8) into use the supplied modular connector cable (B).
the line terminal, and then connect the other
end to the telephone line.
Connecter le MFP à la ligne de téléphone. Pour les modèles 100 V/120 V/Australie ou
7.Brancher le câble du connecteur modulaire Chine, utilisez le câble à connecteur modulaire
(8) à la borne de la ligne, puis connecter (B) fourni.
l'autre extrémité à la ligne de téléphone.
Conecte el MFP a la línea telefónica. Para los modelos de 100 V/120 V/Australiano o
7.Enchufe el cable del conector modular (8) en Chino, utilice el cable conector modular (B)
el terminal de línea y, a continuación, suministrado.
conecte el otro extremo a la línea telefónica.
Anschließen des MFP an die Telefonleitung. Das mitgelieferte Modularsteckerkabel (B) für
7.Telefonmodulkabel (8) in die Gerätebuchse die 100-V/120-V/Australien- oder China-Modelle
einstecken und das Kabel an der Telefon- verwenden.
dose anschließen.
Collegamento dell’MFP alla linea del tele- Per modelli da 100 V/120 V/Australia o Cina, uti-
fono. lizzare il cavo connettore modulare (B) in dota-
7.Inserire il cavo connettore modulare (8) nel zione.
terminale della linea, e quindi collegare
l'altro terminale alla linea del telefono.
将 MFP 连接到电话线对于 100V/120V/ 澳大利亚或中国机型，请使用随

7.将模块接插件电缆 (8) 插入电话线端子，然附的模块接插件电缆 (B)。
后将另一端与电话线连接。
전화회선과 접속 100V/120V/ 오스트레일리아 / 중국사양은 부속

7.모듈코드 (8) 를 라인단자에 꼽습니다 . 다른 모듈코드 (B) 를 사용할 것 .
한 쪽의 플러그는 전화회선과 접속합니다 .
電話回線との接続 100V/120V/ オーストラリア / 中国仕様は付属の

7.モジュラーコード (8) をライン端子に差しモジュラーコード (B) を使用すること。
込む。
もう片方のプラグは、電話回線へ接続
する。
6
10
Connect the MFP to the separate phone (except for New Zealand model). If you don't connect the MFP to the separate
8.Plug the modular connector cable (9) into the telephone terminal, and then connect the other end phone, wipe the surface of the telephone termi-
to the separate phone. nal with alcohol and adhere the terminal seal (C)
upon the customer's request.
On 120 V models, be sure that it is not attached
over the top of the approval label (10).
Connecter le MFP au téléphone séparé. Si le MFP n’est pas connecté au téléphone

8.Brancher le câble du connecteur modulaire (9) à la borne du téléphone, puis connecter l'autre séparé à la demande du client, nettoyer la sur-
extrémité au téléphone séparé. face de la borne de téléphone avec de l’alcool et
apposer le joint de borne (C).
Sur les modèles 120 V, attention à ne pas
installer en recouvrant le haut de l'étiquette
d'approbation (10).
Conecte el MFP al teléfono separado. Si no conecta el MFP a un teléfono separado,

8.Enchufe el cable del conector modular (9) en el terminal del teléfono y, a continuación, conecte el limpie la superficie del terminal del teléfono con
otro extremo al teléfono separado. alcohol y pegue el sello del terminal (C), a solic-
itud del cliente.
En los modelos de 120 V, asegúrese de que no
se fije sobre la etiqueta de aprobación (10).
Anschließen des MFP an das separate Telefon. Wenn der MFP nicht an das separate Telefon ange-
8.Das Telefonmodulkabel (9) in die Telefonbuchse einstecken und das andere Ende an das sepa- schlossen wird, die Oberfläche der Telefonbuchse
rate Telefon anschließen. mit Alkohol abwischen und Verschlusskappe (C)
einsetzen, falls vom Kunden gewünscht.
Bei 120-V-Modellen darauf achten, dass der
Aufkleber nicht den Genehmigungsaufkleber (10)
verdeckt.
Collegamento dell’MFP al telefono separato. Nel caso in cui non si colleghi l'MFP al telefono
8.Inserire il cavo connettore modulare (9) nel terminale del telefono, e quindi collegare l'altro termi- separato, pulire la superficie del terminale del
nale al telefono separato. telefono con dell'alcol e applicare la guarnizione
terminale (C) a richiesta del cliente.
Sui modelli da 120 V, assicurarsi che essa non
venga applicata sopra l’etichetta di approvazi-
one (10).
将 MFP 连接到其它电话如果您没有将 MFP 连接至其他电话，请用酒精擦

8.将模块接插件电缆 (9) 插入电话端子，然后将另一端与其他电话连接。拭电话端子表面，并按照客户要求粘上端子密封
(C)。
120V 规格在粘贴时注意不要与认可标签 (10) 重
叠。
외부 전화와 접속 외부 전화와 접속하지 않는 경우 고객의 요청에

8.모듈코드 (9) 를 TEL 단자에 꼽습니다 . 다른 한 쪽의 플러그는 외부 전화와 접속합니다 . 따라 TEL 단자 주위를 알코올 청소하고 단자씰
(C) 을 붙입니다 .
120V 사양은 허가 라벨 (10) 에 겹치지 않도록
붙일 것 .
外付け電話との接続外付け電話と接続しない場合、お客様の要望に

8.モジュラーコード (9) を TEL 端子に差し込む。
もう片方のプラグは、外付け電話と接続する。より、TEL 端子周囲をアルコール清掃し、端子
シール (C) を貼り付ける。
120V 仕様は認可ラベル (10) に重ならないよう
に、貼りつけること。
7
2
11
C 1
Seal the terminal (for New Zealand model). Wiring the modular connector cable 11.Reinstall the covers (11).
9.Wipe the surface of the telephone terminal (High-speed MFPs only)
with alcohol and adhere the terminal seal 10.Remove the covers (11) and run the modular
(C). connector cable as shown in the figure.
Perform this procedure for New Zealand
model only.
Fermer hermétiquement la borne Câblage du câble à connecteur modulaire 11.Reposer les couvercles (11).
(modèle pour la Nouvelle-Zélande). (MFP à grande vitesse uniquement)
9.Effectuer cette procédure pour le modèle 10.Déposer les couvercles (11) et implanter le
pour la Nouvelle-Zélande seulement. câble à connecteur modulaire comme illustré
par la figure.
Selle el terminal Tendido del cable conector modular 11.Vuelva a instalar las cubiertas (11).
(para el modelo Nuevo Zelandés). (Solo para las MFP de alta velocidad)
9.Realice este procedimiento sólo para el 10.Quite las cubiertas (11) y tienda el cable
modelo Nuevo Zelandés. conector modular como se muestra en la
ilustración.
Versiegeln der Anschlussbuchse Verlegung des Modularsteckerkabels 11.Die Abdeckungen (11) wieder anbringen.
(für Neuseeland-Modell). (Nur MFP der Hochleistungsklasse)
9.Dieses Verfahren nur für das Neuseeland- 10.Die Abdeckungen (11) entfernen und das
Modell anwenden. Modularsteckerkabel gemäß der Abbildung
verlegen.
Sigillare il terminale Cablaggio del cavo connettore modulare 11.Reinstallare i coperchi (11).
(per il modello Nuova Zelanda). (Solo per MFP a velocità alta)
9.Eseguire questa procedura solo per il mod- 10.Rimuovere i coperchi (11) e far passare il
ello Nuova Zelanda. cavo connettore modulare come indicato
nella figura.
安装端子密封 ( 仅适用于新西兰型号 ) 电话线的配线（仅限高速 MFP 时） 11.安装盖板（11）。

9.该操作步骤仅适用于新西兰型号。 10.拆下盖板（11），将电话线如图所示穿过。
단자씰의 부착 ( 뉴질랜드 사양만 ) 모듈코드의 배선（고속 MFP 의 경우만） 11.커버（11）을 장착합니다 .

9.TEL 단자 주위를 알코올청소하고 단자씰 (C) 10.커버（11）를 떼어 내고 모듈코드를 그림과
을 붙입니다 . 같이 지나가게 합니다 .
端子シールの貼り付け ( ニュージーランド仕様モジュラーコードの配線（高速 MFP の場合のみ） 11.カバー

（11）を取り付ける。
のみ ) 10.カバー
（11）を取り外し、モジュラーコードを
9.この手順はニュージーランド仕様のみおこ図のように通す。
なう。
8
(Medium-speed MFPs)
12.Close the cover (4).
(For high-speed MFPs and when the finisher

is installed)
12.Reinstall the cover (4).
(MFP à vitesse moyenne)

12.Fermer le couvercle (4).
(Pour les MFP à grande vitesse quand le

retoucheur est installé)
12.Reposer le couvercle (4).
(MFP de velocidad media)

12.Cierre la cubierta (4).
(Para las MFP de alta velocidad y cuando el

finalizador está instalado)
12.Vuelva a instalar la cubierta (4).
(MFP der mittleren Leistungsklasse)

12.Die Abdeckung (4) schließen.
(Für MFP der Hochleistungsklasse und wenn

der Finisher installiert ist)
12.Die Abdeckung (4) wieder anbringen.
(Per MFP a velocità media)

12.Chiudere il coperchio (4).
(Per MFP a velocità alta e quando la finitrice

è installata)
12.Reinstallare il coperchio (4).
（中速 MFP 时）
12.关闭盖板（4）。
（高速 MFP 且安装装订器时）

12.安装盖板（4）。
( 중속 MFP 의 경우）
12.커버（4）를 닫습니다 .
（고속 MFP 및 피니셔 장착 시의 경우）

12.커버（4）를 장착합니다 .
（中速 MFP の場合）

12.カバー（4）を閉める。
（高速 MFP およびフィニッシャー装着時の場合）

12.カバー（4）を取り付ける。
9
13
12
12
14
Installing the FAX key

13.Insert a flat-head screwdriver at the tip indicated by the arrows (12) as shown on the left, and slide the operation panel covers (13) (14) to remove
them.
Installation de la touche FAX

13.Insérer un tournevis à lame à l'endroit repéré par les flèches (12) comme illustré ci-contre à gauche et faire glisser les couvercles du panneau de com-
mande (13) (14) pour les déposer.
Instalación de la tecla de FAX

13.Inserte un destornillador de pala plana en la punta que indican las flechas (12) como se muestra a la izquierda y deslice las cubiertas del panel de tra-
bajo (13) (14) para quitarlas.
Installieren der FAX-Taste

13.Einen flachen Schraubendreher an der links mit Pfeilen (12) bezeichneten Spitze einschieben und die Bedienfeldabdeckungen (13) (14) verschieben,
um sie dann abzunehmen.
Installazione del tasto FAX

13.Inserire un cacciavite a testa piana nel punto indicato dalla freccia (12) come mostrato sulla sinistra, e slittare i coperchi (13) (14) del pannello opera-
tivo per rimuoverli.
安装 FAX 键
13.如图所示，在▲箭头（12）前方插入一字螺丝刀，滑动并取下操作面板的盖板（13）（14）。
FAX 키 부착
13.그림과 같이 ▲ 표시（12） 앞에 마이너스 드라이버를 삽입해 조작 판넬의 커버（13）（14）를 미끄러트리면서 떼어 냅니다 .
FAX キーの取り付け
13.図のように▲印（12）の先にマイナスドライバーを挿入し、操作パネルのカバー（13）
（14）
をスライドさせて取り外す。
10
15 16 17
14.Remove the clear panel (15). 15.Remove the operation panel sheet (16). 16.Remove the FAX key section cover (17).
14.Déposer le panneau transparent (15). 15.Déposer la tôle du panneau de commande 16.Déposer le couvercle de la partie touche
(16). FAX (17).
14.Quite el panel transparente (15). 15.Quite la hoja del panel de trabajo (16). 16.Quite la cubierta de la sección de la tecla de
FAX (17).
14.Die durchsichtige Platte (15) entfernen. 15.Die Bedienfeldfolie (16) entfernen. 16.Die Abdeckung (17) des FAX-Tastenbe-
reichs entfernen.
14.Rimuovere il pannello trasparente (15). 15.Rimuovere il foglio (16) del pannello opera- 16.Rimuovere la copertura (17) della sezione
tivo. tasto FAX.
14.拆下透明面板（15）。 15.拆下操作面板页（16）。 16.拆下 FAX 键部分的盖板（17）。
14.클리어 판넬（15）을 제거합니다 . 15.조작판넬시트（16）를 제거합니다 . 16.FAX 키 부분의 커버（17）를 제거합니다 .
14.クリアパネル
（15）を取り外す。 15.操作パネルシート（16）
を取り外す。 16.FAX キー部分のカバー
（17）を取り外す。
11
G
17.Install the FAX key (F). 18.Install the FAX key cover (G).
17.Installer la touche FAX (F). 18.Installer le couvercle de la touche FAX (G).
17.Instale la tecla de FAX (F). 18.Instale la cubierta de la tecla de FAX (G).
17.Die FAX-Taste (F) anbringen. 18.Die Abdeckung (G) der FAX-Taste anbrin-
gen.
17.Installare il tasto FAX (F). 18.Installare la copertura (G) del tasto FAX.
17.安装 FAX 键（F）。 18.安装 FAX 键盖板（G）。
17.FAX 키（F）를 부착합니다 . 18.FAX 키커버（G）를 부착합니다 .
17.FAX キー
（F）を取り付ける。 18.FAX キーカバー
（G）を取り付ける。
12
E
D
16 16
Attach the alphabet labels (excluding 100 V models). Attach the FAX operation section label.
19.Wipe the area above the numeric keys on the operation panel sheet 20.Wipe the label surface shown in the figure of the operation panel sheet
(16) with alcohol and attach the alphabet labels (D). (16) with alcohol and attach the FAX operation section label (E) of the
In Asia and Oceania, use PQRS TUV WXYZ label, and do not use corresponding language.
PRS TUV WXY and OPER labels.
Apposer les étiquettes de l’alphabet (Sauf sur les modèles 100 V). Apposer l’étiquette de la section de fonctionnement FAX.
19.Nettoyer à l'alcool la surface au-dessus des touches numériques sur la 20.Nettoyer avec de l’alcool la surface de l’étiquette montrée sur l’illustra-
tôle du panneau de commande (16) et apposer les étiquettes alphabé- tion de la tôle du panneau de commande (16) et apposer l’étiquette de
tiques (D). la section de fonctionnement FAX (E) de la langue correspondante.
En Asie et Océanie, utiliser l’étiquette PQRS TUV WXYZ et pas les
étiquettes PRS TUV WXY et OPER.
Fije las etiquetas de alfabeto (a excepción de los modelos de 100 V). Fije la etiqueta de la sección de funcionamiento del FAX.
19.Limpie el área sobre las teclas numéricas de la hoja del panel de tra- 20.Limpie la superficie de la etiqueta que aparece en la figura de la hoja
bajo (16) con alcohol y fije las etiquetas de alfabeto (D). del panel de trabajo (16) con alcohol y fije la etiqueta de la sección de
En Asia y Oceanía, utilice la etiqueta PQRS TUV WXYZ y no use las funcionamiento del FAX (E) del idioma correspondiente.
PRS TUV WXY ni las OPER.
Anbringen der Alphabetaufkleber (ausgenommen 100-V-Modelle). Anbringen des Aufklebers für den FAX-Bedienungsabschnitt.
19.Den Bereich über den Zifferntasten an der Bedienfeldfolie (16) mit 20.Die in der Abbildung der Bedienfeldfolie (16) gezeigte Klebefläche des
Alkohol abwischen und die Alphabetaufkleber (D) hier anbringen. Aufklebers mit Alkohol reinigen und den Aufkleber für den FAX- Bedi-
In Asien und Ozeanien den Aufkleber PQRS TUV WXYZ verwenden; enungsabschnitt (E) der entsprechenden Sprache anbringen.
nicht die Aufkleber PRS TUV WXY und OPER verwenden.
Applicare le etichette alfabetiche (esclusi i modelli da 100 V). Applicare l'etichetta della sezione funzionamento FAX.
19.Pulire l’area sopra i tasti numerici sul foglio del pannello operativo (16) 20.Pulire con alcool la superficie dell'etichetta indicata in figura del foglio
con alcool ed applicare le etichette alfabetiche (D). del pannello operativo (16), ed applicare l'etichetta della sezione funzi-
In Asia ed Oceania, utilizzare l’etichetta PQRS TUV WXYZ e non utiliz- onamento FAX (E) della lingua corrispondente.
zare le etichette PRS TUV WXY e OPER.
粘贴英文字母标签 (100V 规格以外 ) 粘贴 FAX 操作部标签

19.使用酒精清洁操作面板页（16）的数字键上部，粘贴英文字母标签 (D)。 20.使用酒精清洁操作面板页（16）的插图位置的标签表面后，粘贴对应语
在亚洲和大洋州，请使用 PQRS TUV WXYZ 标签，而不要使用 PRS TUV WXY 言的 FAX 操作部标签 (E)。
和 OPER 标签。
알파벳 라벨의 부착 (100V 사양 이외 ) FAX 조작부라벨의 부착

19.조작판넬시트（16）의 텐키 윗측을 알코올 청소하고 알파벳 라벨 (D) 20.조작판넬시트（16）의 일러스트 위치의 라벨윗면을 알코올청소 후 해
을 붙입니다 . 당하는 언어의 FAX 조작부 라벨 (E) 을 붙입니다 .
아시아?오세아니아에서는 「PRS TUV WXY」 및 「OPER」 라벨을 사
용하지 말고 「PQRS TUV WXYZ」의 라벨을 사용할 것 .
アルファベットラベルの貼り付け (100V 仕様以外 ) FAX 操作部ラベルの貼り付け

19.この作業は不要。 20.操作パネルシート（16）のイラストの位置のラベル上面をアルコール清
掃後、該当する言語の FAX 操作部ラベル (E) を貼り付ける。
13
13
16
15
14
21.Attach the operation panel sheet (16). 22.Reinstall the clear panel (15). 23.Reinstall the operation panel covers (13)
(14).
21.Fixer la tôle du panneau de commande (16). 22.Reposer le panneau transparent (15). 23.Reposer les couvercles du panneau de com-
mande (13) (14).
21.Fije la hoja del panel de trabajo (16). 22.Vuelva a instalar el panel transparente (15). 23.Vuelva a instalar las cubiertas del panel de
trabajo (13) (14).
21.Die Bedienfeldfolie (16) anbringen. 22.Die durchsichtige Platte (15) wieder anbrin- 23.Die Bedienfeldabdeckungen (13) (14) wie-
gen. der anbringen.
21.Applicare il foglio del pannello operativo 22.Reinstallare il pannello trasparente (15). 23.Reinstallare i coperchi (13) (14) del pannello
(16). operativo.
21.安装操作面板页（16）。 22.安装透明面板（15）。 23.安装操作面板的盖板（13）（14）。
21.조작판넬시트（16）를 붙입니다 . 22.클리어판넬（15）를 부착합니다 . 23.조작판넬 커버（13）（14）을 부착합니다 .
21.操作パネルシート（16）
を取り付ける。 22.クリアパネル
（15）を取り付ける。 23.操作パネルのカバー
（13）
（14）
を取り付ける。
14
H
Attach the PTT label (for China, 110 V models only).

24.Attach the PTT label (H) after wiping with alcohol.
Fixer l’étiquette d’approbation (pour la Chine, modèles 110 V seulement).

24.Effectuer cette procédure pour les modèles Chine ou 110 V seulement.
Coloque la etiqueta de aprobación (para China, solo para los modelos de 110 V).
24.Realice el procedimiento sólo para los modelos de Chino o 110 V.
Den Genehmigungsaufkleber anbringen (für China nur 110-V-Modelle).

24.Dieses Verfahren nur für die China- oder 110-VModelle anwenden.
Applicare l’etichetta di approvazione (per Cina, solo per i modelli da 110 V).
24.Eseguire questa procedura solo per modelli da Cina o 110 V.
粘贴规格标签 ( 仅限中国、110V 规格 )
24.用酒精清洁后，请在如图所示的位置贴上规格标签 (H)。
규격라벨의 부착 ( 중국 , 110V 사양만 )

24.이 순서는 중국 , 110V 사양만 실시해 주십시오．
規格ラベルの貼り付け ( 中国、 110V 仕様のみ )

24.この手順は中国、110V 仕様のみおこなう。
15
For Australian model
For New Zealand model
Attach the approval label (for Australian/New Zealand model only). When installing the optional Dual FAX (when
25.Attach the approval label (I) after wiping with alcohol. adding the FAX circuit board to OPT2), proceed
Perform this procedure for Australian/New Zealand model only. to the following procedures.When not installing,
proceed to page 23.
Fixer l’étiquette d’approbation (modèle pour l’Australie/Nouvelle-Zélande seulement). Lorsqu’on installe le FAX double en option
25.Effectuer cette procédure pour le modèle pour l’Australie/Nouvelle-Zélande seulement. (lorsqu’on ajoute la carte à circuits FAX à
l’OPT2), effectuer les procédures suivantes.
Si on ne l’installe pas, passer à la page 23.
Coloque la etiqueta de aprobación (sólo para los modelos Australiano/Nuevo Zelandés) Cuando instale el FAX dual opcional (cuando
25.Realice este procedimiento sólo para los modelos Australiano/Nuevo Zelandés. agrega la tarjeta de circuitos de FAX a OPT2),
vaya a los siguientes procedimientos.
Cuando no lo instala, vaya a la página 23.
Den Genehmigungsaufkleber anbringen (nur für Australien/Neuseeland-Modell). Wenn das optionale Dual FAX installiert wird
25.Dieses Verfahren nur für das Australien/Neuseeland-Modell anwenden. (Hinzufügen der FAX-Leiterplatte zu OPT2), mit
den folgenden Verfahren fortfahren.
Erfolgt diese Installation nicht, mit Seite 23
fortfahren.
Applicare l’etichetta di approvazione (solo per il modello Australia/Nuova Zelanda). Quando si installa il Dual FAX opzionale
25.Eseguire questa procedura solo per il modello Australia/Nuova Zelanda. (quando si aggiunge la scheda a circuiti FAX
all’OPT2), continuare con la seguente
procedura.
Se non si esegue l’installazione passare alla
pagina 23.
粘贴规格标签 ( 仅适用于澳大利亚 / 新西兰型号 ) 安装选购件的多插口组件时 ( 将传真电路板安装

25.该步骤仅适用于澳大利亚 / 新西兰型号时操作。在 OPT2 上时 )，请按以下步骤进行。
不安装时，按第 23 页的要求进行操作。
규격라벨의 부착 ( 오스트레일리아 / 뉴질랜드 사양만 ) 옵션 멀티포트를 설치하는 경우

25.알코올청소 후 규격라벨 (I) 을 부착합니다 . （FAX 기판을 OPT2 에 증설하는 경우）에는 다
음 순서로 진행합니다 .
설치하지 않는 경우에는 23 페이지로 진행합니
다.
規格ラベルの貼り付け ( オーストラリア / ニュージーランド仕様のみ ) オプションのマルチポートを設置する場合

25.この手順はオーストラリア / ニュージーランド仕様のみおこなう。（FAX 基板を OPT2 に増設する場合）は、次の手順
に進む。
設置しない場合は、 23 ページへ進む。
16
1 3
Install the Dual FAX Removing the slot cover 2.Remove 2 screws (2) and then remove the
Refer to page 1 for the supplied parts. (medium-speed MFPs) OPT2 slot cover (3).
1.Open the cover (1).
Installer le FAX double. Dépose du couvercle de la fente 2.Déposer les 2 vis (2) puis le couvercle de la
Pour plus de détails concernant les pièces (MFP à vitesse moyenne) fente OPT2 (3).
fournies, se reporter à la page 1. 1.Ouvrir le couvercle (1).
Instale el FAX dual Desmontaje de la cubierta de la ranura 2.Quite 2 tornillos (2) y, después, quite la cubi-
Consulte la página 1 de las piezas suministra- (MFP de velocidad media) erta de la ranura OPT2 (3).
das. 1.Abra la cubierta (1).
Installieren des Dual FAX Entfernen der Einschubabdeckung 2.2 Schrauben (2) entfernen und dann die
Die mitgelieferten Teile sind auf Seite 1 (MFP der mittleren Leistungsklasse) Abdeckung (3) des Einschubs OPT2 ent-
aufgelistet. 1.Die Abdeckung (1) öffnen. fernen.
Installare il Dual FAX Rimozione del coperchio vano 2.Rimuovere le 2 viti (2) e quinidi rimuovere il
Fare riferimento alla pagina 1 per le parti in dot- (MFP a velocità media) coperchio (3) del vano OPT2.
azione. 1.Aprire il coperchio (1).
安装多插口组件拆下插槽盖板（中速 MFP 时） 2.拆除 2 颗螺丝 (2)，拆下 OPT2 的插槽盖板

同装品时，参照第 1 页。 1.打开盖板 (1)。 (3)。
멀티포트 설치 슬롯커버 제거（중속 MFP 의 경우） 2.나사 (2) 2 개를 제거하고 OPT2 의 슬롯커버
동봉품은 1 페이지를 참조합니다 . 1.커버 (1) 를 엽니다 . (3) 를 제거합니다 .
マルチポートの設置スロットカバーの取り外し（中速 MFP の場合） 2.ビス (2)2 本を外し、OPT2 のスロットカバー

同梱品は 1 ページを参照する。 1.カバー(1) を開ける。 (3) を取り外す。
17
3
1
2
Removing the slot cover (For high-speed 2.Remove 2 screws (2) and then remove the
MFPs and when the finisher is installed) OPT2 slot cover (3).
1.Remove the cover (1).
Dépose du couvercle de la fente (Pour les 2.Déposer les 2 vis (2) puis le couvercle de la
MFP à grande vitesse quand le retoucheur fente OPT2 (3).
est installé)
1.Déposer le couvercle (1).
Desmontaje de la cubierta de la ranura (Para 2.Quite 2 tornillos (2) y, después, quite la cubi-
las MFP de alta velocidad y cuando el final- erta de la ranura OPT2 (3).
izador está instalado)
1.Quite la cubierta (1).
Entfernen der Einschubabdeckung (Für MFP 2.2 Schrauben (2) entfernen und dann die
der Hochleistungsklasse und wenn der Fin- Abdeckung (3) des Einschubs OPT2 ent-
isher installiert ist) fernen.
1.Die Abdeckung (1) entfernen.
Rimozione del coperchio vano (Per MFP a 2.Rimuovere le 2 viti (2) e quinidi rimuovere il
velocità alta e quando la finitrice è installata) coperchio (3) del vano OPT2.
1.Rimuovere il coperchio (1).
拆下插槽盖板 2.拆除 2 颗螺丝 (2)，拆下 OPT2 的插槽盖板

（高速 MFP 且安装装订器时） (3)。
1.拆下盖板 (1)。
슬롯커버 제거 2.나사 (2) 2 개를 제거하고 OPT2 의 슬롯커버

（고속 MFP 및 피니셔 장착 시의 경우） (3) 를 제거합니다 .
1.커버 (1) 를 제거합니다 .
スロットカバーの取り外し（高速 MFP および 2.ビス (2)2 本を外し、OPT2 のスロットカバー

フィニッシャー装着時の場合） (3) を取り外す。
1.カバー(1) を取り外す。
18
4
2
A
Install the FAX circuit board.

3.Insert the FAX circuit board (A) along the groove in OPT2 and secure the board with two screws (2) that have been removed in step 2.
Do not directly touch the FAX circuit board (A) terminal.
Hold the top and bottom of the FAX circuit board, or the projection of the board to insert the FAX circuit board (A).
Direct the label (4) on to the FAX circuit board (A) toward left side and insert the board along the groove.
Installer la carte à circuits FAX.

3.Insérer la carte à circuits FAX (A) le long de la rainure dans l’OPT2 et la fixer à l’aide des deux vis (2) retirées à l’étape 2.
Ne pas toucher directement la borne de la carte à circuits FAX (A).
Tenir les parties inférieure et supérieure de la carte à circuits FAX ou la saillie de la carte pour insérer la carte à circuits FAX (A).
Orienter l'étiquette (4) de la carte à circuits FAX (A) comme illustré et insérer la plaquette le long de la rainure.
Instale la tarjeta de circuitos de FAX.

3.Inserte la tarjeta de circuitos de fax (A) a lo largo de la ranura de OPT2 y asegúrela con los dos tornillos (2) que ha quitado en el paso 2.
No toque directamente el terminal de la tarjeta de circuitos del FAX (A).
Sujete las partes superior e inferior de la tarjeta de circuitos de FAX o la saliente de la tarjeta para insertar la tarjeta de circuitos de FAX (A).
Oriente la etiqueta (4) en la tarjeta de circuitos del FAX (A) como se indica en la ilustración e inserte la tarjeta a lo largo de la ranura.
Installieren der FAX-Leiterplatte.

3.FAX-Leiterplatte (A) in die Nut des Einbauschachts OPT2 einsetzen und Leiterplatte mit den in Schritt 2 ausgebauten Schrauben (2) befestigen.
Berühren Sie die Anschlüsse der FAX-Platine (A) nicht mit den Fingern.
Die FAX-Leiterplatte (A) bein Einsetzen oben und unten oder an dem Vorsprung festhalten.
Die FAX-Leiterplatte (A) so in die Nut einsetzen, dass der Aufkleber (4) wie abgebildet zur Leiterplatte zeigt.
Installare la scheda a circuiti FAX.

3.Inserire la scheda a circuiti FAX (A) lungo l’incavo nell’OPT2 e fissare la scheda con le due viti (2) rimosse nell’operazione 2.
Non toccare direttamente il terminale della scheda a circuiti FAX (A),
Per inserire il circuito FAX (A), tenere l’estremit superiore e la base della scheda a circuiti FAX, o la sporgenza della scheda a circuiti FAX.
Orientare l'etichetta (4) sulla scheda a circuiti FAX (A) come indicato nell'illustrazione e inserire la scheda lungo l'incavo.
安装传真电路板
3.沿着 OPT2 的沟槽插入传真电路板 (A) 并用在步骤 2 中拆下的两颗螺钉 (2) 固定电路板。
请勿直接触摸传真电路板 (A) 端子。
按住传真电路板的顶部和底部，或者按住电路板的突出部将传真电路板 (A) 插入。
将传真电路板 (A) 上的标签 (7) 保持图示中的方向，将电路板沿着沟槽方向插入。
FAX 기판 장착
3.OPT2 구에 붙여 FAX 기판 (A) 를 삽입하고 순서 2 에서 제거한 나사 (2) 2 개로 고정합니다 .
FAX 기판 (A) 의 단자에 직접 닿지 않게 할 것 .
FAX 기판 (A) 을 삽입 시에는 기판의 상하 또는 돌기를 잡을 것 .
FAX 기판 (A) 을 붙여진 라벨 (4) 그림 표기 방향대로 되도록 삽입할 것 .
FAX 基板の取り付け
3.OPT2 の溝に沿って FAX 基板 (A) を挿入し、手順 2 で外したビス (2)2 本で固定する。
FAX 基板 (A) の端子に直接触れないこと。
FAX 基板 (A) の挿入時は基板の上下か突起を持つこと。
FAX 基板 (A) は、貼り付けられているラベル (4) が図に示す方向になるように、挿入すること。
19
5
Seal the terminal. On 120 V models, be sure that it is not attached

4.Wipe the surface of the telephone terminal with alcohol and adhere the terminal seal (C). over the top of the approval label (5).
The telephone terminal on the FAX circuit board installed to OPT2 is unavailable (invalid). Seal
the terminal securely to prevent a user from connecting a separate phone.
Fermer hermétiquement la borne. Sur les modèles 120 V, attention à ne pas

4.Nettoyer la surface de la borne de téléphone avec de l’alcool, et apposer le joint de borne (C). installer en recouvrant le haut de l'étiquette
La borne de téléphone de la carte à circuits FAX installée sur l’OPT2 n’est pas utilisable d'approbation (5).
(invalide). Fermer hermétiquement la borne pour empêcher tout utilisateur de connecter un télé-
phone séparé.
Selle el terminal. En los modelos de 120 V, asegúrese de que no

4.Limpie la superficie del terminal de teléfono con alcohol y pegue el sello de terminal (C). se fije sobre la etiqueta de aprobación (5).
El terminal de teléfono de la tarjeta de circuitos de FAX instalado en el OPT2 no está disponible
(inválido). Selle firmemente el terminal para evitar que un usuario conecte un teléfono por sepa-
rado.
Versiegeln der Anschlussbuchse. Bei 120-V-Modellen darauf achten, dass der

4.Die Oberfläche der Telefonanschlussbuchse mit Alkohol abwischen und die Verschlusskappe (C) Aufkleber nicht den Genehmigungsaufkleber (5)
anbringen. verdeckt.
Die Telefonanschlussbuchse der in OPT2 installierten FAX-Leiterplatte ist nicht verfügbar (ungül-
tig). Die Anschlussbuchse vollkommen versiegeln, um den Anschluss eines separaten Telefons
zu verhindern.
Sigillare il terminale. Sui modelli da 120 V, assicurarsi che essa non

4.Pulire la superficie del terminale del telefono con alcol e fare aderire la guarnizione terminale (C). venga applicata sopra l’etichetta di approvazi-
Il terminale del telefono sulla scheda a circuiti FAX installata su OPT2 non è disponibile (invalido). one (5).
Sigillare il terminale saldamente per prevenire a un utente di collegare un telefono separato.
安装端子密封 120V 规格在粘贴时注意不要与认可标签 (5) 重

4.用酒精擦拭电话端子表面并粘上端子密封 (C)。叠。
安装在 OPT2 上的传真电路板的电话端子不可使用 ( 无效 )。为了避免用户错误与其它电话连接，
必须确实粘贴好端子密封。
단자씰의 부착 120V 사양은 허가 라벨 (5) 에 겹치지 않도록 붙

4.TEL 단자주위를 알코올청소하고 단자씰 (C) 을 부착합니다 . 일 것.
OPT2 에 부착한 FAX 기판의 TEL 단자는 사용불가（무효）가 됩니다 . 사용자가 잘못해 외부 전화
를 접속하지 않도록 확실히 부착할 것 .
端子シールの貼り付け 120V 仕様は認可ラベル（5）に重ならないように、

4.TEL 端子周囲をアルコール清掃し、端子シール (C) を貼り付ける。貼り付けること。
OPT2 に取り付けた FAX 基板の TEL 端子は使用不可（無効）となる。
ユーザーが誤って外付け電話
を接続しないよう確実に貼り付けること。
20
6 B
Connect the MFP to the telephone line.

5.Plug the modular connector cable (6) into the line terminal, and then connect the other end to the
telephone line.
For 100 V/120 V/Australian or Chinese models, use the supplied modular connector cable (B).
Connecter le MFP à la ligne de téléphone.

5.Brancher le câble du connecteur modulaire (6) à la borne de la ligne, puis connecter l'autre
extrémité à la ligne de téléphone.
Pour les modèles 100 V/120 V/Australie ou Chine, utilisez le câble à connecteur modulaire (B)
fourni.
Conecte el MFP a la línea telefónica.

5.Enchufe el cable del conector modular (6) en el terminal de línea y, a continuación, conecte el
otro extremo a la línea telefónica.
Para los modelos de 100 V/120 V/Australiano o Chino, utilice el cable conector modular (B)
suministrado.
Anschließen des MFP an die Telefonleitung.

5.Telefonmodulkabel (6) in die Gerätebuchse einstecken und das Kabel an der Telefondose
anschließen.
Das mitgelieferte Modularsteckerkabel (B) für die 100-V/120-V/Australien- oder China-Modelle
verwenden.
Collegamento dell’MFP alla linea del telefono.

5.Inserire il cavo connettore modulare (6) nel terminale della linea, e quindi collegare l'altro termi-
nale alla linea del telefono.
Per modelli da 100 V/120 V/Australia o Cina, utilizzare il cavo connettore modulare (B) in dota-
zione.
将 MFP 连接到电话线
5.将模块接插件电缆 (6) 插入电话线端子，然后将另一端与电话线连接。
对于 100V/120V/ 澳大利亚或中国机型，请使用随附的模块接插件电缆 (B)。
전화회선과의 접속
5.모듈코드 (6) 를 라인단자에 꼽습니다 . 다른 한 쪽의 플러그는 전화회선과 접속합니다 .
100V/120V/ 오스트레일리아 / 중국사양은 부속 모듈코드 (B) 를 사용할 것 .
電話回線との接続
5.モジュラーコード (6) をライン端子に差し込む。もう片方のプラグは、電話回線へ接続する。
100V/120V/ オーストラリア / 中国仕様は付属のモジュラーコード (B) を使用すること。
21
7 2
Wiring the modular connector cable 7.Reinstall the covers (7). (Medium-speed MFPs)
(High-speed MFPs only) 8.Close the cover (1).
6.Remove the covers (7) and run the modular
connector cable as shown in the figure. (For high-speed MFPs and when the finisher
is installed)
8.Reinstall the cover (1).
Câblage du câble à connecteur modulaire 7.Reposer les couvercles (7). (MFP à vitesse moyenne)
(MFP à grande vitesse uniquement) 8.Fermer le couvercle (1).
6.Déposer les couvercles (7) et implanter le
câble à connecteur modulaire comme illustré (Pour les MFP à grande vitesse quand le
par la figure. retoucheur est installé)
8.Reposer le couvercle (1).
Tendido del cable conector modular 7.Vuelva a instalar las cubiertas (7). (MFP de velocidad media)
(Solo para las MFP de alta velocidad) 8.Cierre la cubierta (1).
6.Quite las cubiertas (7) y tienda el cable
conector modular como se muestra en la (Para las MFP de alta velocidad y cuando el
ilustración. finalizador está instalado)
8.Vuelva a instalar la cubierta (1).
Verlegung des Modularsteckerkabels 7.Die Abdeckungen (7) wieder anbringen. (MFP der mittleren Leistungsklasse)
(Nur MFP der Hochleistungsklasse) 8.Die Abdeckung (1) schließen.
6.Die Abdeckungen (7) entfernen und das
Modularsteckerkabel gemäß der Abbildung (Für MFP der Hochleistungsklasse und wenn
verlegen. der Finisher installiert ist)
8.Die Abdeckung (1) wieder anbringen.
Cablaggio del cavo connettore modulare 7.Reinstallare i coperchi (7). (Per MFP a velocità media)
(Solo per MFP a velocità alta) 8.Chiudere il coperchio (1).
6.Rimuovere i coperchi (7) e far passare il
cavo connettore modulare come indicato (Per MFP a velocità alta e quando la finitrice
nella figura. è installata)
8.Reinstallare il coperchio (1).
电话线的配线（仅限高速 MFP 时） 7.安装盖板（7）。（中速 MFP 时）

6.拆下盖板（7），将电话线如图所示穿过。 8.关闭盖板（1）。
（高速 MFP 且安装装订器时）

8.安装盖板（1）。
모듈코드의 배선（고속 MFP 의 경우만） 7.커버（7）을 장착합니다 . ( 중속 MFP 의 경우）

6.커버（7）를 떼어 내고 모듈코드를 그림과 같 8.커버（1）를 닫습니다 .
이 지나가게 합니다 .
（고속 MFP 및 피니셔 장착 시의 경우）
8.커버（1）를 장착합니다 .
モジュラーコードの配線（高速 MFP の場合のみ） 7.カバー

（7）を取り付ける。（中速 MFP の場合）
6.カバー
（7）を取り外し、
モジュラーコードを 8.カバー（1）を閉める。
図のように通す。
（高速 MFP およびフィニッシャー装着時の場合）
8.カバー（1）を取り付ける。
22
Initialize the FAX circuit board. 3.If the FAX circuit board has been added to OPT2 (to initialize the FAX
1.Plug the MFP into a power outlet, and turn on the main power. circuit board in OPT2)
2.If the FAX circuit board has been installed only in OPT1 or installed Initialize OPT2 by pressing [PORT2], and the Start key in this order in
both in OPT1 and OPT2 (to initialize all FAX circuit boards) Perform the the maintenance mode U698 and executing the maintenance mode
maintenance mode U600 to initialize the fax control assembly. U600. If [ALL] is selected in U698, both OPT1 and OPT2 are initialized.
For details, see the service manual.
Refer to the operation guide to create a FAX Box.
Initialiser la carte à circuits FAX. 3. Si la carte à circuits FAX a été ajoutée à l’OPT2 (pour initialiser la carte à circuits
1.Brancher le MFP sur une prise d’alimentation et le mettre sous tension. FAX dans l’OPT2)
2.Si la carte à circuits FAX a été installée dans l’OPT1 seulement, ou a Initialiser l’OPT2 en appuyant sur [PORT2] et la touche Départ dans cet ordre en
été installée dans l’OPT1 et dans l’OPT2 (pour initialiser toutes les mode de maintenance U698, et exécuter le mode de maintenance U600. Si [ALL]
est sélectionné dans U698, l’OPT1 et l’OPT2 sont tous deux initialisés. Pour plus
cartes à circuits FAX) Exécuter le mode de maintenance U600 pour ini-
de détails, se reporter au manuel d’entretien.
tialiser l’ensemble de commande de fax.
Se reporter au manuel d’utilisation pour créer une Boîte de FAX.
Inicialice la tarjeta de circuitos FAX. 3. Si la tarjeta de circuitos de FAX se agregó a OPT2 (para inicializar la tarjeta de
1.Conecte el MFP a un receptáculo de pared y encienda el interruptor circuitos de FAX en OPT2)
principal. Inicialice el OPT2 presionando [PORT2] y la tecla de Inicio en ese orden en el
2.Si la tarjeta de circuitos de FAX se instaló solo en OPT1 o se instaló modo de mantenimiento U698 y ejecutando el modo de mantenimiento U600. Si
se selecciona [ALL] en U698, se inicializan ambos OPT1 y OPT2. Para más det-
tanto en OPT1 como OPT2(para inicializar todas las tarjetas de circuito
alles, lea el manual de servicio.
de FAX) Ejecute el modo de mantenimiento U600 para inicializar el
Consulte la guía de uso para crear un Buzón de FAX.
conjunto de control de fax.
Initialisieren der FAX-Leiterplatte. 3. Wenn die FAX-Leiterplatte zu OPT2 hinzugefügt worden ist (um die FAX-Leiter-
1.Netzstecker des MFP in eine Steckdose stecken und Hauptschalter platte in OPT2 zu in7itialisieren)
einschalten. OPT2 initialisieren. Dazu [PORT2] und die Start-Taste im
2.Wenn die FAX-Leiterplatte nur in OPT1 oder sowohl in OPT1 als auch Wartungsmodus U698 in dieser Reihenfolge drücken und den
Wartungsmodus U600 ausführen. Wenn [ALL] in U698 gewählt wird, werden
in OPT2 installiert worden ist (um alle FAX-Leiterplatten zu initialisie-
OPT1 und OPT2 initialisiert. Weitere Einzelheiten siehe Wartungsanleitung.
ren) Wartungsmodus U600 ausführen, um die Faxsteuerbaugruppe zu
Schlagen Sie zur Erzeugung einer FAX-Box in der Einfuhrung nach.
initialisieren.
Inizializzare la scheda a circuiti FAX. 3. Se la scheda a circuiti è stata aggiunta all’OPT2 (per inzializzare la scheda a cir-
1.Collegare l’MFP ad una presa di corrente e portare l’interruttore princi- cuiti FAX nell’OPT2)
pale su On. Inizializzare OPT2 premendo [PORT2] e il tasto Avvio in questo ordine nel modo
2.Se la scheda a circuiti FAX è stata installata solo nell’OPT1 o in di manutenzione U698 ed eseguendo il modo di manutenzione U600. Se viene
selezionato [ALL] nel modo U698, entrambi OPT1 e OPT2 sono inizializzati. Per
entrambi l’OPT1 e l’OPT2(per inizializzare tutte le schede di circuito
ulteriori dettagli leggere il manuale d’istruzioni.
FAX) Eseguire il modo di manutenzione U600 per inizializzare il
Leggere la guida alle funzioni per creare una Casella FAX.
gruppo di controllo fax.
传真电话板的初始化 3.在 OPT2 上增设时

1.将 MFP 插入电源插座，打开主电源。 (OPT2 的传真电路板初始化 )
2.仅限于在 OPT1 或 OPT1 和 OPT2 上同时安装传真电路板时 ( 全部的传真只进行 OPT2 初始化时，在维修保养模式 U698 状态下，按顺序按下
电路板初始化 ) “PORT2”、开始键，执行维修保养模式 U600。
执行维修保养模式 U600，初始化传真控制组件在 U698 状态下设定 “ALL” 时，会使 OPT1 和 OPT2 均初始化。
有关详信息，请参见维修手册。参照操作手册，作成传真盒。
FAX 기판의 초기화 3. OPT2 에 증설한 경우 (OPT2 의 FAX 기판을 초기화 )

1.MFP 본체 전원플러그를 콘센트에 꼽고 주 전원 스위치를 ON 으로 한 메인터넌스모드 U698 에서 「PORT2」, 시작키 순으로 누릅니다 . 메인터넌
다. 스 모드 U600 을 실행하고 FAX 기판을 초기화합니다 .
2.OPT1 만 또는 OPT1 와 OPT2 에 FAX 기판을 동시에 설치한 경우 ( 전 U698 에서 「ALL」을 설정하면 OPT1 과 OPT2 양쪽을 초기화하기 때문에
주의할 것 .
부 FAX 기판을 초기화 ) 메인터넌스 모드 U600 을 실행하고 FAX 기판
상세는 서비스 매뉴얼을 참조할 것 .
을 초기화합니다 .
사용설명서를 참조해 팩스박스를 작성합니다 .
FAX 基板の初期化 3.OPT2 に増設した場合 (OPT2 の FAX 基板を初期化 )

1.MFP 本体の電源プラグをコンセントに差し込み、主電源スイッチを ON メンテナンスモード U698 で「PORT2」、スタートキーの順に押す。メンテ
にする。ナンスモード U600 を実行し、FAX 基板を初期化する。
2.OPT1 のみまたは OPT1 と OPT2 に FAX 基板を同時に設置した場合 ( すべ U698 で「ALL」を設定すると OPT1 と OPT2 両方を初期化するので注意す
ての FAX 基板を初期化 ) メンテナンスモード U600 を実行し、FAX 基板ること。詳細はサービスマニュアルを参照のこと。
を初期化する。使用説明書を参照し、ファクスボックスを作成する。
23
2011
2011

Taskalfa 3050ci PDF

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

Taskalfa 3050ci PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Taskalfa 3050ci PDF

Uploaded by

Copyright:

Available Formats

TASKalfa 3050ci

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE

IL Y A UN RISQUE D’EXPLOSION SI LA BATTERIE EST REMPLACEE PAR UN MODELE

Notation of products in the manual

TASKalfa 3050ci: 30 ppm model

General warning. Warning of risk of electric shock.

Warning of high temperature.

General prohibited action. Disassembly prohibited.

Always ground the copier.

• Always use parts having the correct specifications. ............................................................................

• Remove toner completely from electronic components. .....................................................................

1-3 Maintenance Mode

(3) Scan to E-mail error codes ........................................................................................... 1-4-108

1-5 Assembly and disassembly

1-5-8 Drive section ........................................................................................................................ 1-5-70

1-6 Requirements on PWB Replacement

2-1 Mechanical Construction

2-2 Electrical Parts Layout

2-3 Operation of the PWBs

2-3-8 Feed PWB 2 ........................................................................................................................ 2-3-75

Warm-up Power on 25 s or less 25 s or less 30 s or less 30 s or less

550 sheets (64 g/m2)

Main Standard 2048 MB

Operating Humidity 15 to 80% RH

Resolution 600 x 600 dpi

Scanning speed B/W : 70 images/min B/W : 80 images/min

Interface Ethernet (10 BASE-T/100 BASE-TX/1000 BASE-T)

NOTE: These specifications are subject to change without notice.

1-1-2 Parts names

1. Original size indicator plate 11. Handles

21. Inner tray 31. Paper conveying unit lever

1. Machine 7. SMT paper feeder

(3) Operation panel

1. Program key 11. Power key 21. Memory indicator

1-1-3 Machine cross section

1-2-1 Installation environment

1. Temperature: 10 to 32.5°C/50 to 90.5°F

30cm/11 13/16" 35cm/13 3/4"

1-2-2 Unpacking and installation

Unpacking Installing the waste toner box

Removing the eject spacer Replacing operation panel sheet

Removing the tapes

Installing the paper feeder (option)

Release the lock of the scanner mirror frame

Release of lift plate stopper

Installing the toner containers

Unlocking the developer waste

Moving the machine

1. Machine 12. Machine cover

Place the machine on a level surface.

Removing the eject spacer

1. Remove the eject spacer and silica gel

Removing the tapes

1. Remove three tapes and then remove Tape A3 papers

3. Remove six tapes.

Installing the paper feeder (option)

1. Install the optional paper feeder or large

Release the lock of the scanner mirror frame