P100 T16000 SM PDF

Maintenance and Service Manual
T16000
Powershift
Transmission
SPICER® OFF HIGHWAY-PRODUCTS™
814922
TOWING OR PUSHING
Before towing the vehicle, be sure to lift the rear wheels off the ground or disconnect the driveline to avoid
damage to the transmission during towing.
Note: If the transmission has 4 wheel drive, disconnect both front and rear drivelines.
Because of the design of the hydraulic system, the engine cannot be started by pushing or
towing.
©Copyright DANA CORPORATION 1990. Unpublished material.
All rights reserved.
Limited Distribution.
No part of this work may be reproduced in any form under any means
without direct written permission of the DANA CORPORATION.
T16000 03/00
FOREWORD
This manual has been prepared to provide the customer and the maintenance personnel with information
and instructions on the maintenance and repair of the SPICER OFF-HIGHWAY PRODUCTS product.
Extreme care has been exercised in the design, selection of materials, and manufacturing of these units.
The slight outlay in personal attention and cost required to provide regular and proper lubrication, inspection
at stated intervals, and such adjustments as may be indicated will be reimbursed many times in low cost
operation and trouble free service.
In order to become familiar with the various parts of the product, its principle of operation, troubleshooting,
and adjustments, it is urged that the mechanic study the instructions in this manual carefully and use it as
a reference when performing maintenance and repair operations.
Whenever repair or replacement of component parts is required, only SPICER OFF-HIGHWAY PRODUCTS
approved parts as listed in the applicable parts manual should be used. Use of “will-fit” or non-approved parts
may endanger proper operation and performance of the equipment. SPICER OFF-HIGHWAY PRODUCTS
does not warrant repair or replacement parts, nor failures resulting from the use of parts which are not
supplied by or approved by SPICER OFF-HIGHWAY PRODUCTS PRODUCTS.
Important: Always furnish the Distributor with the serial and model number when ordering parts.
T16000 03/00
TABLE OF CONTENTS
CHAPTER
Foreword
Safety precautions
Cleaning and inspection, legend symbols 1
Technical specifications 2
a. Identification of the unit
b. Weight, oil capacity, dimensions
c. Tightening torques
d. Pressure and temperature specifications
e. Electrical specifications
f. Hydraulic cooler lines
Maintenance 3
a. Oil specification
b. Maintenance intervals
c. Servicing machine after components overhaul
d. Parking brake adjustment
Installation details 4
a. Converter drive coupling
b. Components to engine installation
c. External plumbing
Operation of the unit 5

a. Hydraulic circuit
b. Transmission assembly
c. Electric solenoid control
d. Power flows
e. Gear and clutch lay-out
Troubleshooting 6
a. Stall procedure
b. Check points
c. Electrical wiring
Sectional views and parts identification 7
Assembly instructions 8
Disassembly and reassembly of units 9
Service tools 10
T16000
SAFETY PRECAUTIONS
To reduce the chance of personal injury and/or property damage, the following instruction must be carefully
observed.
Proper service and repair are important to the safety of the service technician and the safe, reliable operation
of the machine. If replacement parts are required the part must be replaced with one of the same part
number or with a equivalent part. Do not use a replacement part of lesser quality.
The service procedures recommended in this manual are effective methods of performing service and repair.
Some of these procedures require the use of tools specifically designed for the purpose.
Accordingly, anyone who intends to use a replacement part, service procedure or tool, which is not
recommended by SPICER OFF-HIGHWAY PRODUCTS, must first determine that neither his safety nor
the safe operation of the machine will be jeopardized by the replacement part, service procedure or tool
selected.
It is important to note that this manual contains various ’Cautions’ and ‘Notices’ that must be carefully observed
in order to reduce the risk of personal injury during service or repair, or the possibility that improper service
or repair may damage the unit or render it unsafe. It is also important to understand that these ‘Cautions’ and
‘Notices’ are not exhaustive, because it is impossible to warn of all the possible hazardous consequences
that might result from failure to follow these instructions.
T16000 03/00
CLEANING AND INSPECTION
CLEANING
Clean all parts thoroughly using solvent type cleaning fluid. It is recommended that parts be immersed in
cleaning fluid and moved up and down slowly until all old lubricant and foreign material is dissolved and parts
are thoroughly cleaned.
CAUTION
CARE SHOULD BE EXERCISED TO AVOID SKIN RASHES, FIRE HAZARDS, AND INHALATION OF VAPOURS WHEN USING
SOLVENT TYPE CLEANERS.
BEARINGS
Remove bearings from cleaning fluid and strike flat against a block of wood to dislodge solidified particles of
lubricant. Immerse again in cleaning fluid to flush out particles. Repeat above operation until bearings are
thoroughly clean. Dry bearings using moisture-free compressed air. Be careful to direct air stream across
bearing to avoid spinning. Do not spin bearings when drying. Bearings may be rotated slowly by hand to
facilitate drying process.
HOUSINGS
Clean interior and exterior of housings, bearing caps, etc., thoroughly. Cast parts may be cleaned in hot
solution tanks with mild alkali solutions providing these parts do not have ground or polished surfaces. Parts
should remain in solution long enough to be thoroughly cleaned and heated. This will aid the evaporation of
the cleaning solution and rinse water. Parts cleaned in solution tanks must be thoroughly rinsed with clean
water to remove all traces of alkali. Cast parts may also be cleaned with steam cleaner.
CAUTION
CARE SHOULD BE EXERCISED TO AVOID INHALATION OF VAPOURS AND SKIN RASHES WHEN USING
ALKALI CLEANERS.
All parts cleaned must be thoroughly dried immediately by using moisture-free compressed air or soft, lintless
absorbent wiping rags free of abrasive materials such as metal fillings, contaminated oil, or lapping compound.
INSPECTION
The importance of careful and thorough inspection of all parts cannot be overstressed. Replacement of all
parts showing indication of wear or stress will eliminate costly and avoidable failures at a later date.
BEARINGS
Carefully inspect all rollers: cages and cups for wear, chipping, or nicks to determine fitness of bearings for
further use. Do not replace a bearing cone or cup individually without replacing the mating cup or cone at the
T16000 03/00 1-1

Cleaning and inspection
same time. After inspection, dip bearings in Automatic Transmission Fluid and wrap in clean lintless cloth or
paper to protect them until installed.
OIL SEALS, GASKETS, ETC.

Replacement of spring load oil seals, O-rings, metal sealing rings, gaskets, and snap rings is more economical
when unit is disassembled than premature overhaul to replace these parts at a future time. Further loss of
lubricant through a worn seal may result in failure of other more expensive parts of the assembly. Sealing
members should be handled carefully, particularly when being installed. Cutting, scratching, or curling under
of lip of seal seriously impairs its efficiency. When assembling new metal type sealing rings, same should be
lubricated with coat of chassis grease to stabilize rings in their grooves for ease of assembly of mating
members. Lubricate all O-rings and seals with recommended type Automatic Transmission Fluid before
assembly.
GEARS AND SHAFTS

If magna-flux process is available, use process to check parts. Examine teeth on all gears carefully for wear,
pitting, chipping, nicks, cracks, or scores. If gear teeth show spots where case hardening is worn through or
cracked, replace with new gear. Small nicks may be removed with suitable hone. Inspect shafts and quills to
make certain they are not sprung, bent, or splines twisted, and that shafts are true.
HOUSING, COVERS, ETC.

Inspect housings, covers and bearing caps to be certain they are thoroughly clean and that mating surfaces,
bearing bores, etc., are free from nicks or burrs. Check all parts carefully for evidence of cracks or condition
which would cause subsequent oil leaks or failures.
Legend symbols
Smontaggio di sottogruppi Sostituire con ogni montaggio

Disassembly of assembly groups Renew at each reassembly
Montaggio di sottogruppi Togliere - mettere la sicura

Reassemble to from assembly group Unlock - lock e.g. split pin, locking plate, etc.
Smontaggio di particollari ingombranti Mettere la sicura, incollare (mastice liquido)

Remove obstruction parts Lock - adhere (liquid sealant)
Montaggio di particollari ingombranti Evitare danni ai materiali, danni ai pezzi

Reinstall - remount parts which had obstructed disassembly Guard against material damage, damage to parts
Attenzione, indicazione importante Marchiari prima dello smontaggio (per il montaggio)

Attention! important notice Mark before disassembly, observe marks when reasembl.
Controllare regolare p.e. coppie, misure, pressione etc. Carricare riempire (olio - lubrificante)
Check - adjust e.g. torque, dimensions, pressures etc. Filling - topping up - refilling e.g. oil, cooling water, etc.
T = Attrezzature speciali P = Pagina Scarricare olio, lubrificante

T = Special tool P = Page Drain off oil, lubricant
Rispettare direzione di montaggio Tendere

Note direction of installation Tighten - clamp ; tightening a clamping device
Controllare esaminare controllo visuale Insere pressione nel circuito idraulico

Visual inspection Apply pressure into hydraulic circuit
Eventualimente riutilizzable (sostituire se necessario) Pulire

Possibly still serviceable, renew if necessary To clean
T16000 03/00 1-2

TECHNICAL SPECIFICATIONS
A. IDENTIFICATION OF THE UNIT
1. Model and type of the unit

2. Serial number
B. WEIGHT, DIMENSIONS, OIL CAPACITY

Weight (dry) 290 kg (639 lb)
Maximum length 705,3 mm (27,8”)
Maximum width 465 mm (18,3”)
Maximum height 648 mm (25,35”)
Oil capacity:
14 l (3,7 US Gallon) without cooler and hydraulic lines.
Consult operator’s manual on applicable machine for system capacity
T16000 03/00 2-1

Technical specifications
C. TIGHTENING TORQUE’S
Torque table for bolts.

(Based in VDI 2230, µ = 0,14 and CCI standard)
All threads must be lubricated before assembly.
Metric Inch
Class 8,8 Torque Grade 5 Torque
Nm lbft Nm lbft
M5 x 0,8 5-6 3,7 - 4,4 0,5000 87-95 64,1 - 70,0
M8 x 1,25 20 - 25 14,7 - 18,4
M10 x 1,5 40 - 50 29,5 - 36,8
Torque tables for plugs (o-ring ports)
Metric Inch
Size Torque Size Torque
Nm lbft Nm lbft
M10 x 1 8 - 10 5,9 - 7,4 1,3125 - UN 112 - 140 82,5 - 103,2
M22 x 1,5 48 - 60 35,4 - 44,2
M33 x 2 112 - 140 82,5 - 103,2
Torque tables for pipe plugs
Metric Inch
Size Torque Size Torque
Nm lbft Nm lbft
M22 x 1,5 48 - 60 35,4 - 44,2 0,1250 - 27 9 - 13 6,6 - 9,6
UNI 7707 NPTF
Output flanges
339 - 407 Nm (250 - 300 lbft).
Filter torque
30-38 Nm (22,1-28 lbft).
Control valve
Connector nut to cover: 6 - 8 Nm (4,4 - 5,9 lbft).
T16000 03/00 2-2

D. PRESSURE AND TEMPERATURE SPECIFICATIONS
• Normal operating temperature 70 - 120°C (158 - 248F) measured at temperature check port to cooler
(port 71 - **).
• Maximum allowed transmission temperature 120°C (248 F).
• Transmission regulator pressure (*) - (neutral 2nd speed) - port 31 (**).
- at 600 RPM min. 16,5 bar (239 PSI).
- at 2200 RPM : 19,6 - 23,1 bar (284 - 335 PSI).
• Pump flow (*)

- at 2200 RPM in neutral 2nd speed : 64,9 l/min. minimum (17,1 GPM).
- at 2200 RPM in reverse 1st, 2 nd, forward 1st, 2nd maximum 3 l/min. (0,8 GPM) less than in neutral 2nd.
- at 2200RPM in forward 3rd and 4th : maximum 5l/min. (1,3 GPM) less than in neutral 2nd.
• Clutch pressures (*)

- 1st clutch : port 41 (**).
- 2nd clutch : port 42 (**).
- forward high clutch : port 44 (**).
- forward low clutch : port 45 (**).
- reverse clutch : port 46 (**).
- disconnect clutch : port 47 (**).
at 2200 RPM :
- 18,1 - 21,5 bar (263 - 312 PSI) clutch activated.
- 0 - 0,2 bar (0 - 3 PSI) clutch released.
• Filter bypass valve set at 4,1 - 5 bar(*) (59 - 73 PSI), measured between port 31 and 35.
• Lube pressure (*) (port 33) - 0,3 - 0,5 bar (4,3 - 7,3 PSI) at 47 l/min. (12,4 GPM) pump flow
(±1800 RPM).
• Internal leakage (*) 1,5 - 3,0 l/min. (0,4 - 0,8 GPM) for each clutch.
Max. total leakage 6,8 l/min (1,8 GPM) (clutch leakage dir. + range + converter leak + valve leak) without
disconnect clutch.
• Safety valve : cracking pressure (*) 9,5 - 10,5 bar (138 - 152 PSI), measured at port 34.
• To cooler (converter out) pressure (*) (port 32) 2 bar min. (29 PSI) at 2000 RPM and max. 5 bar (73 PSI)
at no load governed speed).
• Converter by pass valve set at 5 - 7 bar (*) (73 - 102 PSI), measured between port 33 and 34.
(*) All pressures and flows to be measured with oil temperature of 82 - 93° C ( 180 - 200F).
(**) Refer to section troubleshooting for check port identification.
T16000 03/00 2-3

E. ELECTRICAL SPECIFICATIONS
• Solenoid (forward reverse, high/low, 2nd/1st, modulation, disconnect)

coil resistance : 28 Ω ± 2 Ω (20°C).
• Electronic controlled modulation valve :

coil resistance : 3,55 Ohm (± 0,25 Ohm) at 20°C (68F).
• Speed sensor :
- type: magneto resistive sensor with 7/14 mA current loop.
- frequency: 0 - 25000 Hz.
- sensing distance: 0 - 2,5 mm.
• Temperature sensor (in speed sensor) resistance versus temp: see table.
Tamb Resistance Tamb Resistance

°C Ω °C Ω
-55 980 50 2417

-50 1030 60 2597
-40 1135 70 2785
-30 1247 80 2980
-20 1367 90 3182
-10 1496 100 3392
0 1630 110 3607
10 1772 120 3817
20 1922 125 3915
25 2000 130 4008
30 2080 140 4166
40 2245 150 4280
F. HYDRAULIC COOLER LINES SPECIFICATIONS
• Minimum 19 mm internal diameter for lines and fittings.
• Suitable for operation from ambient to 120° C continuous operating temperature.
• Must withstand 20 bar continuous pressure and with 40 bar intermittent surges.
• Conform SAE J1019 and SAE J517,100RI.
T16000 03/00 2-4

MAINTENANCE
A. OIL SPECIFICATION
ATF oil only which meets following specifications:

• ATF Elfmatic G3.
A. MAINTENANCE INTERVALS
• Daily:
Check oil level daily with engine running at idle (600 RPM) and oil at 82 - 93°C (180 - 200 F).
Maintain oil level at full mark.
• Normal drain period:

Normal drain period and oil filter change are for average environment and duty cycle condition.
Severe or sustained high operating temperature or very dusty atmospheric conditions will cause accelerated
deterioration and contamination.
For extreme conditions judgement must be used to determine the required change intervals.
- Every 1000 hours change oil filter.

- Every 1000 hours drain and refill system as follows:
Drain with oil at 65 - 93°C (150 - 200 F).
1. Drain transmission.
2. Oil filter, remove and discard, install new filter.
3. Refill transmission (14 litres) (3,7 G).
4. Run engine at idle (600 RPM) to prime converter and lines.
5. When oil temperature is at 82 - 93°C (180 - 200 F) adjust oil level to full mark.
Note: It is recommended that oil filter be changed after 100 hours of operation on new,
rebuilt or repaired unit.
T16000 03/00 3-1

Maintenance
C. SERVICING MACHINE AFTER COMPONENTS OVERHAUL
The transmission, torque converter, and its allied hydraulic system are important links in the driveline between
the engine and the wheels. The proper operation of either unit depends greatly on the condition and operation
of the other; therefore, whenever repair or overhaul of one unit is performed, the balance of the system must
be considered before the job can be considered complete.
After the overhauled or repaired transmission has been installed in the machine, the oil cooler, and connecting
hydraulic system must be thoroughly cleaned. This can be accomplished in several manners and a degree of
judgement must be exercised as to the method employed.
The following are considered the minimum steps to be taken:
1. Drain entire system thoroughly.

2. Disconnect and clean all hydraulic lines. Where feasible hydraulic lines should be removed from machine
for cleaning.
3. Replace oil filter elements cleaning out filter cases thoroughly.
4. The oil cooler must be thoroughly cleaned. The cooler should be “back flushed” with oil and compressed
air until all foreign material has been removed. Flushing in direction of normal oil flow will not adequately
clean the cooler. If necessary, cooler assembly should be removed from machine for cleaning, using oil,
compressed air, and steam cleaner for that purpose. DO NOT use flushing compounds for cleaning purposes.
5. Reassemble all components and use only type oil recommended for lubrication section.
Fill transmission through filler opening until fluid comes up to the oil level check port.
Run engine 2 minutes at 500+600 R.P.M. to prime torque converter and hydraulic lines.
Recheck level of fluid in transmission with engine running at idle (500-600 R.P.M.).
Add quantity necessary to bring fluid level to oil level check port.
Recheck with hot oil (180-200 F) 82-93° C.
6. Recheck all drain plugs, lines, connections, etc., for leaks and tighten where necessary.
T16000 03/00 3-2

Maintenance
D. INSTRUCTIONS FOR LINING REPLACEMENT AND ADJUSTMENT OF PARKING BRAKE ASSEMBLY
1. Loosen two adjustment locking nuts (4 & 5) enough to slide each torque plate (16 & 18) away from disc far
enough to provide clearance to remove old carrier and lining assemblies and install new ones.
(It may be necessary to remove one or both nuts).
2. Collapse lining retraction spring (21) and remove from brake head assembly.
3. Slide torque plates (16 & 18) away from disc, move carrier and lining assemblies (17) out of pockets, and
remove from the brake head assembly from the side.
4. Install new carrier and lining assemblies (17) in each torque plate (16 & 18).
5. Install lining retention spring (21) into brake head assembly. Be sure spring’s “feet” are positioned properly
in holes in both lining carrier assemblies (17).
6. Tighten inner adjusting nut (5) until firm contact is made with the disc by the linings. Torque to (100 lbs-in)
11 Nm make certain lever is in proper operating position for application.
7. Back off inner adjusting nut 4 (5) to 5 flats and check that disc is free to move
(total clearance 0,8 - 1,1 mm (0.031 - 0.043)).
8. Tighten outer locking nut (4) against inner adjusting nut to lock adjustment bolt in place.
Torque to (45 to 55 lb-ft.) 61 - 75 Nm.
19
20
3
19
2 18
1
17
21
15
16
14
12 13
11
10
9
8
7
6
5
4
T16000 03/00 3-3

INSTALLATION DETAILS
A. CONVERTER DRIVE COUPLING
Measure the “A” dimension (bolt circle diameter) and order drive plate kit listed below.
Note two (2) kits have (2) intermediate drive plates and one (1) drive plate and weld nut assembly.
Two (2) kits with three intermediate drive plates.
(1) DRIVE PLATE AND WELD NUT ASSEMBLY
A A
BOLT CIRCLE DIA. BOLT CIRCLE DIA.

BACKING RING (2) INTERMEDIATE DRIVE PLATES BACKING RING (3) INTERMEDIATE DRIVE PLATES
“A” Dimension (Bolt circle diameter) “A” Dimension (Bolt circle diameter)
• 13.125” (333,38 mm) diameter • 13.125” (333,38 mm) diameter
Kit No. 802424 Kit No. 802426
• 13.500” (342,90 mm) diameter • 13.500” (342,90 mm) diameter
Kit No. 802425 Kit No. 802427
Each kit will include the following parts: Kit will include the following parts:
• 2 Intermediate drive plates • 3 Intermediate drive plates
• 1 Drive plate and weld nut assembly • 1 Backing ring
• 1 Backing ring • 6 Mounting screws
• 6 Mounting screws • 6 Lock washers
• 6 Lock washers • 1 Instruction sheet
• 1 Instruction sheet
Position drive plate and weld nut assembly on torque converter assembly with weld nuts toward converter.
Align intermediate drive plates and backing ring with holes in torque converter assembly.
Note
Two dimples 180° apart in backing ring must be out (Toward the engine flywheel).
Install cap screws and washers. Tighten (26 to 29 lbft) torque 35 - 39 Nm.
T16000 03/00 4-1

B. TRANSMISSION TO ENGINE INSTALLATION PROCEDURE
1. Remove all burrs from flywheel mounting face
and nose pilot bore. Clean drive plate surface with
solvent.
FLYWHEEL HOUSING MOUNT
2. Check engine flywheel & housing for DIAL INDICATOR
HERE
conformance to standard SAE No. 3 per SAE
J927 and J1033 tolerance specifications for pilot
bore size, pilot bore runout and mounting face ENGINE
flatness. Measure and record engine crankshaft

end play. FLYWHEEL
PILOT BORE
3. Install two (2.50) 63,500 mm long transmission
to flywheel housing guide studs in the engine
flywheel housing as shown. Rotate the engine FLYWHEEL
flywheel to align a drive plate mounting screw

hole with the flywheel housing access hole.
FIG. 1
*4. Install a (4.00) 101,60 mm long drive plate
locating stud .3750 - 24 fine thread in a drive plate
nut. Align the locating stud in the drive plate with
the flywheel drive plate mounting screw hole
positioned in step No. 3.
5. Rotate the transmission torque converter to align FLYWHEEL HOUSING CONVERTER HOUSING
the locating stud in the drive plate with the
flywheel drive plate mounting screw hole
positioned in step No. 3. Locate transmission on
flywheel housing. 4"STUD
Aligning drive plate to flywheel and transmission

to flywheel housing guide studs, install
transmission to flywheel housing screws. Tighten 21/2"ALIGNING
STUDS
screws to specified torque. Remove transmission
to engine guide studs. Install remaining screws FLYWHEEL
DRIVE
PLATE
and tighten to specified torque.
*6. Remove drive plate locating stud. FIG. 2
7. Install drive plate attaching screw and washer.
Snug screw but do not tighten. Some engine
flywheel housings have a hole located on the
flywheel housing circumference in line with the SPECIAL STUD, WASHER AND
drive plate screw access hole. A screwdriver or SELF LOCK NUT FURNISHED
FLYWHEEL HOUSING BY ENGINE MANUFACTURER.
pry bar used to hold the drive plate against the
flywheel will facilitate installation of the drive plate
screws. Rotate the engine flywheel and install the
remaining seven (7) flywheel to drive plate FLYWHEEL
attaching screws. Snug screws but do not tighten.

After all eight (8) screws are installed torque one IMPELLER
COVER
(26 to 29) lbft torque 35 - 39 Nm. This will require
tightening each screw and rotating the engine
INTERMEDIATE
flywheel until the full amount of eight (8) screws DRIVE PLATES
have been tightened to specified torque.
8. Measure engine crankshaft end play after
transmission has been completely installed on
FIG. 3 FIG.4
engine flywheel. This value must be within (.001)
0,025 mm of the end play recorded in step No. 2.
* Does not apply to units having 3 intermediate drive
plates. (See fig. 4)
T16000 03/00 4-2

C. EXTERNAL PLUMBING
To cooler from converter
Transmission cooler
From cooler to
transmission lube
distributor
Cooler lines specifications
• Minimum 19 mm internal diameter for lines and fittings.
• Suitable for operation from ambient to 120° C continuous operating temperature.
• Must withstand 20 bar continuous pressure and with 40 bar intermittent surges.
• Conform SAE J1019 and SAE J517,100RI
T16000 03/00 4-3

TORQUE CONVERTER NEUTRAL, 2ND CLUTCH AND DISCONNECT CLUTCH ENGAGED
OPERATOR COMPARTMENT BY-PASS VALVE
PRESSURE DIFFERENCE 4 BAR
T16000
PRESSURE TEMPERATURE
GAUGE GAUGE
X : PRESSURE
bar CHECK PORT
X : TEMPERATURE
TORQUE °C CHECK PORT
CONVERTER
34 32 AA 33
bar bar °C bar
COOLER
71
HOSE HOSE
°C
LUBRICATION
SOLENOID PRESSURE 5 bar
SAFETY VALVE
10 bar CRACKING PRESSURE
SOLENOID
SOLENOID SOLENOID SOLENOID SOLENOID RANGE SOLENOID
N / FWD N / REV HIGH / LOW 2ND / FST MODULATION DISCONNECT
PRESSURE
REDUCER
TO 5,5 bar
03/00
PRESSURE
REGULATOR
VALVE
20 bar
31 ELECTRONIC
CONTROLLED
bar
MODULATION
VALVE
5,5 TO 0 bar
FILTER
BY-PASS VALVE
PRESSURE DIFFERENCE
4,3 bar ACCUMULATOR
35 PRESSURE BOOSTER
bar 46 45 44 42 41 47
0 - 5,5 TO 0 - 20 bar
bar bar bar bar bar bar
MODULATED PRESSURE
PUMP REV F LOW F HIGH 2ND 1ST DISCONNECT
0 TO 20 bar
CLUTCH CLUTCH CLUTCH CLUTCH CLUTCH CLUTCH
AIR
BREATHER
SCREEN
CLUTCH PRESSURE 20 bar
OIL SUMP
5-1
OPERATION OF THE UNIT
The transmission and hydraulic torque converter of the power train enacts an important role in transmitting
engine power to the driving wheels. In order to properly maintain and service these units it is important to first
understand their function and how they operate.
A. THE HYDRAULIC CIRCUIT (REFER TO HYDRAULIC DIAGRAM)

The transmission and torque converter function together and operate through a common hydraulic system.
With the engine running, the transmission charging pump draws oil through the oil suction screen and directs
it through the oil filter and pressure regulating valve.
Across the oil filter is a filter by pass valve which will open if the pressure difference becomes higher than
4,3 bar (62 PSI).
The pressure regulating valve maintains pressure for the control valve and clutches at 20 bar (288 PSI).
Excess oil volume is bled off into the converter circuit. A safety valve is fitted between the pressure regulator
and converter. The valve will open if pressure in this line becomes higher than 10 bar (144 PSI).
After entering the converter the oil is directed through the converter blade cavity and exits in the passage
between the turbine shaft and pump drive shaft and flows to the cooler.
After leaving the cooler the oil is directed to a fitting on the transmission. Then through a series of tubes and
passages lubricates and cools the transmission bearings and clutches.
The oil then gravity drains back to the transmission sump.
Across the converter and oil cooler is a converter by pass valve which will open if the pressure difference is
higher than 4 bar (58 PSI) (during start up from cold or at high RPM).
T16000 03/00 5-2

Operation of the unit
B. THE TRANSMISSION ASSEMBLY
Basically the transmission is composed of five main assemblies:
1. The converter and pump drive section.
2. The input or directional clutches.
3. The range clutches.
4. The output section.
5. The transmission controls.
T16000 03/00 5-3

1. The converter and pump drive section
Engine power is transmitted from the engine flywheel to the impeller through the impeller cover.
This element is the pump portion of the hydraulic torque converter and is the primary component which starts
the oil flowing to the other components which results in torque multiplication. This element can be compared
to a centrifugal pump in that it picks up fluid at its centre discharges at its outer diameter.
The torque converter turbine is mounted opposite the impeller and is connected to the turbine shaft or
directional clutch shaft. This element receives fluid at its outer diameter and discharges at its centre.
The reaction member of the torque converter is located between and at the centre of the inner diameters of
the impeller and turbine elements. Its function is to take the fluid which is exhausting from the inner portion of
the turbine and change its direction to allow correct entry for recirculation into the impeller element.
This recirculation will make the converter to multiply torque.
The torque multiplication in function of the balding (impeller, turbine and reaction member) and the converter
output speed (turbine speed). The converter will multiply engine torque to its designed maximum multiplication
ratio when the turbine shaft is at zero RPM (stall).
Therefore we can say that as the turbine shaft is decreasing in speed, the torque multiplication is increasing.
In the impeller cover a splined shaft is fitted which runs inside and through the turbine shaft to drive a
hydraulic pump which is fitted at the back of the transmission. Since the shaft is connected to the centre of the
impeller cover, the pump speed will be the same as engine speed.
The rear side of the impeller cover has a tanged drive which drives the transmission charging pump located
in the converter housing. The transmission charging pump speed is also the same as the engine speed.
The convertor and pump drive section
T16000 03/00 5-4

2. The input or directional clutches
The turbine shaft driven from the turbine transmits power to the forward or reverse clutches.
These clutches consists of a drum with splines and a bore to receive a hydraulic actuated piston.
The piston is oil tight by the use of sealing rings. A steel disc with external splines is inserted into the drum
and rests against the piston. Next, a friction disc with splines at the inner diameter is inserted.
Discs are alternated until the required total is achieved.
A back up plate is then inserted and secured with a span ring. A hub with outer diameter splines is inserted
into the splines of discs with teeth on the inner diameter. The discs and hub are free to increase in speed or
rotate in the opposite direction as long as no pressure is present in that specific clutch.
To engage the clutch, the control valve which is fitted on the side of the transmission will direct oil under
pressure through tubes and passages to the selected clutch shafts.
Oil sealings are located on the clutch shafts. These rings direct the oil through a drilled passage in the shaft
to the desired clutch.
Pressure of the oil forces the piston and discs against the back up plate. The discs with splines on the outer
diameter clamping against discs with teeth on the inner diameter enables the drum and hub to be locked
together and allows them to drive as one unit.
When the clutch is released, a return spring will push the piston back and oil will drain back via the control
valve into the transmission sump.
The T16000 transmission has one reverse clutch and two forward clutches (forward low and forward high).
This in combination with the two range clutches result in the transmission having 4 forward speeds and
2 reverse speeds.
The engagement of the directional clutches is modulated; which means that clutch pressure is built up gradually.
This will enable the unit to make forward, reverse shifts while the vehicle is still moving and will allow smooth
engagement of drive. The modulation is controlled electronically in the control valve.
The input or directional clutches
T16000 03/00 5-5

3. The range clutches
Once a directional clutch is engaged power is transmitted to the range clutches (1st or 2nd).
Operation and actuation of the range clutches is similar as the directional clutches.
The engagement of the range clutches is also modulated to enable a smooth engagement.
The modulation for these clutches is achieved by means of a restrictor valve fitted in the control valve which
is controlled electronically and which limits oil flow to the clutch during shifts. In the clutch itself the plate
before the end plates is dished to build up the clamping force of the clutch gradually.
4. The output section
With a range clutch engaged power is finally transmitted to the output shafts.
The T16000 transmission can have an upper output or lower output at the rear side of the unit, and a lower
output at the front side. Output rotation of the rear upper output is opposite the engine rotation when the
forward clutch is engaged, while output rotation of the lower rear output and the front output is the same as
the engine rotation with the forward clutch engaged.
Ration between upper and lower output is 0,951:1.
The lower front output has an axle disconnect clutch to enable 4 wheel drive.
The clutch is similar as the other clutches except that it has no modulation. The disconnect is controlled
electronically. Without an electrical signal the clutch is always engaged.
The range clutches The output section
T16000 03/00 5-6

5. The transmission controls (refer to hydraulic diagram)
The transmission is controlled by an electronic gear selector (EGS). This unit has a microprocessor which
receives certain inputs (gear selector position, speed sensor, ...) which are processed and will give output
signals to the control valve.
The control valve has 6 solenoid, 6 shift spools, a pressure reducer, an electronic controlled modulation
valve, an accumulator, a pressure booster and a speed sensor.
The transmission controls
Operation of the valve is as follows:

Regulated pressure 20 bar (290 PSI) is directed to the shift spools, pressure booster and pressure reducer.
In the pressure reducer, regulated pressure is reduced to 5,5 bar (80 PSI). This reduced pressure is used as
supply for the solenoid and electronic controlled modulation valve.
When activated, the electronic controlled modulation valve will give an output pressure curve from 0 to 5 bar
(0 to 80 PSI).
This pressure curve is multiplied in the booster so that a curve from 0 to 20 bar (0 to 290 PSI) is available for
the directional clutches. Between the electronic modulation valve and the booster is an accumulator to damper
any hydraulic vibration.
When forward is selected the electronic modulation valve and the forward solenoid are activated.
The pilot pressure of the forward solenoid will move the shift spool so that a forward clutch can be fed with
modulated pressure.
If the high/low solenoid is not activated the forward high clutch is engaged, if it is activated the forward low
clutch is engaged.
When reverse is selected the electronic modulation valve and the reverse solenoid are activated, the pilot
pressure of the reverse solenoid will move the shift spool so that the reverse clutch can be fed with modulated
pressure.
The shift spools from forward and reverse are located against each other with a return spring in between;
this is to make sure that only one direction can be selected.
Range is selected as follows:
If the range solenoid (2nd / 1st) is not activated, regulated pressure is fed through the modulation shift spool
and through the 2nd / 1st shift spool to the 2nd clutch.
If the range solenoid (2nd / 1st) is activated, the pilot pressure will move the shift spool so that 1st clutch is fed.
T16000 03/00 5-7

The range clutches also have modulation which operates as follows:

When the range is changed, oil will flow through the modulation shift spool to the chosen range clutch
momentary until the friction discs are closed against the dished plate. At that moment the range modulation
solenoid is activated.
The plot pressure will move the modulation shift spool so that oil supply is fed through a restrictor which is in
by pass of the valve.
The controlled volume of oil is used to push in the dished outer plate gradually until the clutch is fully closed.
This will give a smooth build up of torque. At that moment the range modulation solenoid is released,
so that the modulation shift spool return to its rest position and allowing full oil flow to the clutch.
The control valve also controls the front lower output disconnect clutch. If the solenoid is not activated full oil
pressure is fed through the disconnect shift spool to the disconnect clutch. If the solenoid is activated,
pilot pressure will move the disconnect shift spool to block oil supply to the disconnect clutch to release it.
The control valve also has a speed sensor. This sensor will pick up upper output gear speed. This information
is used in the electronic gear selector to determine shift logic. Since the sensor picks up upper output gear
speed, the signal will be in direct relation of the turbine speed if any directional clutch is engaged.
C. ELECTRIC SOLENOID CONTROLS
Transmission gear Activated solenoids Activated clutches
Forward 4 Forward Forward high, 2nd

Forward 3 Forward, 2nd / 1st Forward high, 1st
Forward 2 Forward, Forward high / low Forward low, 2nd
Forward 1 Forward, Forward high / low, 2nd / 1st Forward low, 1st
Reverse 1 Reverse, 2nd / 1st Reverse, 1st

Reverse 2 Reverse Reverse, 2nd
Disconnect off Disconnect ---------------

Disconnect on ---------------- Disconnect
T16000 03/00 5-8

D.POWER FLOWS
1st SPEED FORWARD 2nd SPEED FORWARD
3rd SPEED FORWARD 4th SPEED FORWARD
T16000 03/00 5-9

D. POWER FLOWS
1st SPEED REVERSE
2nd SPEED REVERSE
T16000 03/00 5 - 10
E. GEAR AND CLUTCH LAY-OUT
t
t pu
Ou
t
pu
In
p ut
O ut
Forward Low
Forward High
Reverse and 1st
2nd
Disconnect
T16000 03/00 5 - 11
TROUBLESHOOTING GUIDE FOR THE T16000 TRANSMISSION
The following information is presented as an aid to isolating and determining the specific problem area in a
transmission that is not functioning correctly.
When troubleshooting a “transmission” problem, it should be kept in mind that the transmission is only the
central unit of a group of related powertrain components. Proper operation of the transmission depends on
the condition and correct functioning of the other components of the group. Therefore, to properly diagnose
a suspected problem in the transmission, it is necessary to consider the transmission fluid, charging pump,
torque converter, transmission assembly, oil cooler, filter, connecting lines, and controls, including the engine,
as a complete system.
By analyzing the principles of operation together with the information in this section, it should be possible to
identify and correct any malfunction which may occur in the system.
T16000 TRANSMISSION
T16000 (power shift with torque converter transmission) troubles fall into three general categories: mechanical
hydraulic and electrical problems.
In addition to the mechanical and electrical components, all of which must be in the proper condition and
functioning correctly, the correct functioning of the hydraulic circuit is most important. Transmission fluid is
the “life blood” of the transmission. It must be supplied in an adequate quantity and delivered to the system
at the correct pressures to ensure converter operation, to engage and hold the clutches from slipping, and to
cool and lubricate the working components.
TROUBLESHOOTING PROCEDURES
Stall Test:
Use a stall test to identify transmission, converter, or engine problems.
Transmission pressure checks:

Transmission problems can be isolated by the use of pressure tests. When the stall test indicates slipping
clutches, then measure clutch pack pressure to determine if the slippage is due to low pressure or clutch
plate friction material failure.
In addition, converter charging pressure and transmission lubrication pressure may also be measured.
Mechanical and electrical checks:

Prior to checking any part of the system for hydraulic function (pressure testing), the following mechanical
and electrical checks should be made:
• Check the parking brake for correct adjustment.
• Be sure all lever linkage is properly connected and adjusted in each segment and at all connecting points.
• The controls are actuated electrically. Check the wiring and electrical components.
• Be sure that all components of the cooling system are in good condition and operating correctly.
The radiator must be clean to maintain the proper cooling and operating temperatures for the engine and
transmission. Air clean the radiator, if necessary.
• The engine must be operating correctly. Be sure that it is correctly tuned and adjusted to the correct idle
and maximum no-load governed speed specifications.
T16000 03/00 6-1

Troubleshooting guide
Hydraulic check:
Also, before checking the transmission clutches, torque converter, charging pump, and hydraulic circuit for
pressure and rate of oil flow, it is important to make the following transmission fluid check:
Check oil level in the transmission. The transmission fluid must be at the correct (full level). All clutches and
the converter and its fluid circuit lines must be fully charged (filled) at all times. See NOTE below.
NOTE: The transmission fluid must be at operating temperature of 82 - 93° C (180 - 200 F) to
obtain correct fluid level and pressure readings.
DO NOT ATTEMPT TO MAKE THESE CHECKS WITH COLD OIL.
To raise the oil temperature to this specification it is necessary to either operate (work) the vehicle or run the
engine with converter at “stall”. (Refer to converter stall procedure).
CAUTION: Be careful that the vehicle does not move unexpectedly when operating the engine and
converter at stall R.P.M.
A. CONVERTER STALL PROCEDURE
1. Put the vehicle against a solid barrier, such as a wall, and/or apply the parking brake and block the wheels.
2. Put the directional control lever in FORWARD (or REVERSE, as applicable).
3. Select the highest speed.
With the engine running, slowly increase engine speed to approximately one-half throttle and hold until
transmission (converter outlet) oil temperature reaches the operating range.
CAUTION: Do not operate the converter at stall condition longer than 30 seconds at one time, shift
to neutral for 15 seconds and repeat the procedure until desired temperature is reached.
Excessive temperature (120° C) 250 F maximum) will cause damage to transmission
clutches, fluid, converter, and seals.
T16000 03/00 6-2

TROUBLESHOOTING GUIDE
Refer to the following troubleshooting guide for the diagnosis of typical transmission troubles.
LOW CLUTCH PRESSURE

CAUSE REMEDY
1. Low oil level 1. Fill to proper level
2. Clutch pressure regulating valve stuck open 2. Clean valve spool and housing
3. Faulty charging pump 3. Replace pump
4. Broken or worn clutch shaft or piston sealing rings 4. Replace sealing rings
LOW CHARGING PUMP OUTPUT

CAUSE REMEDY
2. Suction screen plugged 2. Clean section pump
3. Defective charging pump 3. Replace pump
OVERHEATING
CAUSE REMEDY
1. Worn oil sealing rings 1. Remove, disassemble, and rebuild converter
assembly
2. Worn charging pump 2. Replace
4. Dirty oil cooler 4. Clean cooler
5. Restriction in cooler lines 5. Change cooler lines
NOISY CONVERTER
CAUSE REMEDY
1. Worn charging pump 1. Replace
2. Worn or damaged bearings 2. A complete disassembly will be necessary to
determine what bearing is faulty
LACK OF POWER
CAUSE REMEDY
1. Low engine R.P.M. at converter stall 1. Tune engine check governor
2. See “Overheating” and make same checks 2. Make corrections as explained in “Overheating”
T16000 03/00 6-3

B. CHECK POINTS
DIPSTICK HOLE
1.3125-12UN-2B THD
SAE O-RING PORT
FRONT VIEW
PORT 44
PRESSURE CHECK PORT FWD HI CLUTCH
(FWD 3RD AND FWD 4TH)
PORT 33
PRESSURE CHECK PORT FROM COOLER
(LUBE PRESSURE)
PORT 45
PRESSURE CHECK PORT FWD LOW CLUTCH
(FWD 1ST AND FWD 2ND)
PORT 11
TO COOLER
PORT 46
PRESSURE CHECK PORT REV. CLUTCH
(REV. 1ST AND REV. 2ND)
PORT 41
PRESSURE CHECK PORT 1ST CLUTCH
(FWD 1ST, FWD 3RD,REV. 1ST)
PORT 12
FROM COOLER
OIL LEVEL PLUG M10 X1
MAGNETIC DRAIN
PLUG M22 X 1,5
REAR VIEW
T16000 03/00 6-4

PORT 11
PORT 34
TO COOLER
PRESSURE CHECK PORT
CONVERTER IN
PORT 42
PRESSURE CHECK PORT
2ND CLUTCH
(FWD 2ND - FWD 4TH - REV. 2ND)
PORT 47
PRESSURE CHECK PORT -
DISCONNECT CLUTCH
(4 WHEEL DRIVE)
LEFT SIDE VIEW
PORT 31 FILTER PLUG M22 X 1,5 THD

PRESSURE CHECK PORT
REGULATOR PRESSURE
TOP VIEW
T16000 03/00 6-5

PORT 71
TEMPERATURE CHECK PORT
CONVERTER OUT TO COOLER
PORT 32
PRESSURE CHECK PORT
CONVERTER OUT TO COOLER
BOTTOM VIEW
Threads
All pressure and temperature check ports:

• M10 x 1 THD
o-ring port ISO 6149-1
All hydraulic line connection ports:
• 1,0625-12 UN 2B
SAE-o-ring port
PORT 35
PRESSURE BEFORE FILTER
RIGHT SIDE VIEW
T16000 03/00 6-6

SECTIONAL VIEWS AND PARTS IDENTIFICATION
T16000 03/00 7-1

GROUP - CONVERTER HOUSING & TRANSMISSION CASE
51
47 50
46 52
49
7 48 53
51
8
52
1 60
9
59
2
6 10
1 54
5 2
4
3 55
1 1 58
1 2 51 62
52 61
45
4 27 52
26 29 1 34 51 51
28 2 52
2 51
2 1 13 57 56
2
3 33 35
52
1 14 51
2 32
2 1 31
1 30
19 2
20 1
34
21
15
25
22 16
23 17
11 18
24 12
42
42
43 41
40
39
37 38
40
39
40 42
39
36 44
7-2 03/00 T16000

Item Description Quantity
1 Plug 11
2 “O” ring plug 11
4 Plug 3
5 Ball 1
6 Spring 1
7 Plug 1
9 Spring safety valve 1
10 Ball 1
12 Plug 1
13 “O” ring - converter housing to transmission case 2
14 “O” ring - converter housing to transmission case 2
15 Gasket - converter housing to tranmission case 1
16 Housing - converter 1
17 Lockwasher - converter housing to transmission case screw 14
18 Screw - converter housing to transmission case 14
19 “O” ring - filter adaptor 1
20 “O” ring - filter adaptor 1
21 Filter - adaptor 1
22 Lockwasher - filter adaptor screw 3
23 Screw - filter adaptor 3
24 Assembly - filter 1
25 Oil seal - output shaft front 1
30 Clip - suction tube 1
31 Lockwasher - suction tube screw 1
32 Screw - suction tube 1
33 “O” ring - suction tube 1
34 Retainer - suction tube 1
35 Assembly - tube & screen 1
36 Baffle - oil 1
37 Lockwaher - oil baffle mountng screw 3
38 Screw - oil baffle mounting 3
39 Nut - oil baffle mounting screw 5
40 Lockwasher - oil baffle mounting screw 5
41 Baffle - oil 1
42 Screw - oil baffle mounting 5
43 Plate - oil baffle 1
44 Plate - oil baffle 1
45 Pin - transmission case to converter dowel 2
48 Case - transmission 1
T16000 03/00 7-3

51
47 50
46 52
49
7 48 53
51
8
52
1 60
9
59
2
6 10
1 54
5 2
4
3 55
1 1 58
1 2 51 62
52 61
45
4 27 52
26 29 1 34 51 51
28 2 52
2 51
2 1 13 57 56
2
3 33 35
52
1 14 51
2 32
2 1 31
1 30
19 2
20 1
34
21
15
25
22 16
23 17
11 18
24 12
42
42
43 41
40
39
37 38
40
39
40 42
39
36 44
7-4 03/00 T16000

50 Plug 1
51 Plug 11
53 Seal upper output 1
56 Plug - magnetic drain 1
57 Snapring - output shaft rear bearing 1
58 Plug - output shaft bore 1
59 Sealing ring - plug 1
60 Plug 1
61 Plug 1
62 Plug 1
T16000 03/00 7-5

GROUP - INPUT SHAFT, TORQUE CONVERTER,PUMP DRIVE, INTERNAL CHARGING PUMP AND DRIVE PLATE
12
11
10
9
7
8
5
6
4
3 23
22
21
2
1
20
19
18
17
30 32
16
29 31
15
14
13 28
27
26
25
24
7-6 03/00 T16000

GROUP - INPUT SHAFT, TORQUE CONVERTER,PUMP DRIVE, INTERNAL CHARGING PUMP AND DRIVE PLATE
1 Screw - drive plate mounting 6

2 Lockwasher - drive plate mounting screw 6
3 Ring - drive plate 1
4 Plate - drive 2
5 Assembly - drive plate 1
6 Bushing - converter pilot 1
7 Assembly - torque converter 1
8 Oil seal - charging pump 1
9 Screw - pump mounting 6
10 Seal washer - pump mounting screw 6
11 Assembly - charging pump 1
12 “O” ring - charging pump 1
13 Ring - piston 1
14 Bearing - input shaft front 1
15 Snap ring 1
16 Snap ring 1
17 Gear - forward low & reverse drive 1
18 Snap ring 1
19 Shaft - input 1
20 Snap ring 1
21 Gear - forward high drive 1
22 Bearing - input shaft rear 1
23 Ring - piston 1
24 Assembly - pump drive shaft & sleeve 1
25 Ring - piston 1
26 Bearing - pump drive shaft 1
27 Snap ring 1
28 Retaining ring 1
29 Gasket - permanent pump adapter cover 1
30 Cover - permanent pump adapter 1
31 Lockwasher - permanent pump adapter cover screw 4
32 Screw - permanent pump adapter cover 4
T16000 03/00 7-7

GROUP - FWD LOW/FWD HIGH SHAFT
18
17
5
4
2 3
1
16
15
14
13
12
11
10
9
8
7
6 32
31
30
29
28
27
26
25
50
24
49
23 48
22 47
46
21
20 45
19
44
43
42
41
40
39
38
37
36
34 35
33
7-8 03/00 T16000

GROUP - FWD LOW/FWD HIGH SHAFT
1 Bearing -front Fwd low / Fwd high shaft 1

2 Gear -forward driven 1
3 Snap ring 1
4 Bearing-clutch gear 1
5 Retaining ring-clutch gear bearing 1
6 Gear forward low clutch 1
7 Ring - clutch gear piston 1
8 Retaining ring - clutch gear bearing 1
9 Bearing - clutch gear 1
10 Snap ring 1
11 Snap ring 1
12 Washer 1
13 Snap ring-backing plate 1
14 Plate-clutch disc backing 1
15 Disc-outer half 1
16 Disc-outer 8
17 Disc-inner 9
19 Ring-retaining 1
20 Retainer spring 1
21 Spring-piston return 1
22 Plate spring-clutch piston wear 1
23 Assembly-clutch piston & seals 1
24 Seal-clutch piston-outer 1
25 Seal-clutch piston-inner 1
26 Assembly Fwd.low/Fwd.high,shaft drum & plug 1
29 Assembly clutch piston & seals 1
30 Plate spring clutch piston wear 1
31 Spring piston return 1
33 Spacer clutch spring fwd high 1
34 Ring-retaining 1
36 Disc-inner 4
37 Disc-outer 3
40 Spacer-clutch disc backing plate Fwd/high 1
41 Snap ring spacer 1
42 Thrust washer 1
43 Thrust bearing 1
44 Bearing-needle 1
45 Gear-forward high clutch 1
46 Bearing-needle 1
47 Thrust bearing 1
48 Thrust washer 1
49 Bearing-rear Fwd low/Fwd high shaft 1
50 Ring-piston 3
T16000 03/00 7-9

GROUP - REVERSE/1ST SHAFT AND GEARS
9
8
7
6
5
4
2 3
18
1 16 17
15
14 32
13
12
11
31
10
30
29
27 28
26
47
25
46
24 45
44
23
22 43
21
42
20
19
41
40
39
38
37
36
34 35
33
7 - 10 03/00 T16000
GROUP - REVERSE/1ST SHAFT AND GEARS
1 Bearing -front Rev.:1st shaft 1

2 Gear -reverse driven 1
3 Snap ring 1
4 Bearing-clutch gear 1
6 Gear forward low clutch 1
7 Ring - clutch gear piston 1
10 Snap ring 1
11 Snap ring 1
12 Washer 1
13 Snap ring-backing plate 1
16 Disc-outer 8
17 Disc-inner 9
19 Ring-retaining 1
26 Assembly Rev./1st,shaft drum & plug 1
29 Assembly clutch piston & seals 1
30 Plate clutch piston wear 1
31 Assembly-spring disc 1
32 Ring-retaining 1
34 Disc-inner 9
35 Disc-outer 8
37 Modulation spring 1
39 Snap ring-clutch disc backing plate 1
40 Bearing clutch gear 1
42 Gear-1st clutch 1
45 Snap ring 1
46 Bearing-rear Rev./1st shaft 1
47 Ring-piston 3
T16000 03/00 7 - 11
GROUP - 2ND SHAFT
7
6
5
4
3
2
15
14
1 13
12
11
10
9
8
23
22
21
20
19
18
17 31
16 30
29
28
27
26
25
24
7 - 12 03/00 T16000
GROUP - 2ND SHAFT
1 Ring-piston 2
2 Bearing-front 2nd.shaft 1
3 Washer-bearing support 1
5 Retaining-ring clutch gear bearing 1
6 Gear-2nd clutch 1
9 Snap ring-cluch disc backing plate 1
11 Modulation spring 1
13 Disc-outer 8
14 Disc-inner 9
16 Ring retaining 1
18 Spring clutch-piston return 1
23 Assembly-2nd shaft,drum & plug 1
24 Snap ring-gear retainer 1
25 Gear-lower output drive 1
26 Gear-upper output 1
27 Bearing rear-2nd shaft 1
28 Flange yoke 1410-upper output 1
29 “O”ring-flange 1
30 Washer-flange nut 1
31 Nut-flange 1
T16000 03/00 7 - 13
GROUP - OUTPUT SHAFT WITH INTERNAL DISCONNECT
13
12
11
10
8
7
5
4
22
3 21
2
1 20
19
18
17
16
15
32
31
30
29
28
14
27
26
25
24
23
7 - 14 03/00 T16000
GROUP - OUTPUT SHAFT WITH INTERNAL DISCONNECT
1 Nut-flange 1
2 Washer-flange nut 1
3 “O”ring-flange 1
4 Output flange front yoke 1410 with brake disc 1
5 Bearing-output shaft front 1
6 Ring-retaining 1
7 Disconnect hub 1
8 Snapring-gear retainer 1
9 Assembly-output shaft front 1
10 Bushing 2
11 Snapring-clutch disc backing plate 1
12 Spacer 1
13 Plate clutch disc backing 1
15 Disc-outer 11
16 Disc-inner 12
18 Ring-retaining 1
25 Assembly-output shaft rear, drum & plug 1
26 Snapring-gear retainer 1
27 Gear lower output 1
28 Snapring gear retainer 1
29 Snap ring - rear bearing 1
30 Bearing - output shaft rear 1
31 Snap ring - rear bearing 1
32 Ring-piston 3
T16000 03/00 7 - 15
GROUP - PARKING BRAKE
19
20
3
19
2 18
1
17
21
15
16
14
12 13
11
10
9
8
7
6
5
4
7 - 16 03/00 T16000
GROUP - PARKING BRAKE
1 Screw-brake mounting 2
2 Assembly-caliper 1
3 Nut- brake mounting screw 2
4 Nut-jam adjustment 1
5 Nut-adjustment 1
6 Washer-hardened 1
7 Washer-stainless steel 1
8 Washer-trust 1
9 Lever 1
10 Boot 1
11 Cam 1
12 Id seal 1
13 Ball bearing 3
14 Plastic retainer 1
15 Cam 1
16 Torque plate-front 1
17 Carrier and lining assembly 2
18 Torque plate-rear 1
19 Sleeve mounting 2
20 Bolt-Adjusting 1
21 Spring 1
T16000 03/00 7 - 17
GROUP - MOUNTING ELECTRIC CONTROL VALVE
6 3
7 - 18 03/00 T16000
GROUP - MOUNTING ELECTRIC CONTROL VALVE
1 Control valve assembly 1

2 Control valve mounting screws 17
3 Control valve protection cover gasket 1
4 Control valve protection cover 1
5 Protection cover screw 20
6 Air breather 1
T16000 03/00 7 - 19
GROUP - ELECTRIC CONTROL VALVE ASSEMBLY
28
16
27
6
37
15
.
DIR .
D
MO
39 NG
E
RA D.
MO
14
5 13 26
HI-
W
LO
D.
FW
38
12 1&
2
V.
RE
25 DIS
C.
40
36
11
4 18
23
10
3 9 24
17
8 35
22
2
34
7 19 21
31 33
32
1 20
29
41
42
30
43
44
46
45
47
48
7 - 20 03/00 T16000
GROUP - ELECTRIC CONTROL VALVE ASSEMBLY
1 Spool body 1
2 Pressure reducer spool 1
3 Pressure reducer spring 1
4 Separator plate 1
5 Pressure regulator spring 1
6 Pressure regulator spool 1
7 Pilot spool spring 1
8 Disconnect spool 1
9 Spool stop 1
10 Separator plate 1
11 1st/2nd spool 1
13 Spool stop 1
15 Range modulation spool 1
17 Accumulator spring 1
18 Accumulator spool 1
19 Booster spool 1
20 Reverse spool 1
22 Forward spool 1
23 Spool stop 1
25 Fwd. low/Fwd. high spool 1
27 Spool cover 1
28 Spool cover screw 11
29 Check port plugs 4
30 Spool body to solenoid plate screw 3
31 Spacer plate 1
32 Bypass valve spool 1
33 Bypass valve spring 1
34 Solenoid plate 1
35 Plug 6
36 Solenoid 6
37 Electronic controlled modulation valve 1
38 Solenoid clamp 1
39 Solenoid clamp screw 6
40 Wiring strap 6
41 Speed sensor 1
42 Speed sensor “O” ring 1
43 Jam nut “O” ring 1
44 Jam nut 1
45 Wiring harness, “O” rings and speed sensor assembly 1
46 Wiring clamp 1
47 Clamp screw lockwasher 1
48 Clamp screw 1
T16000 03/00 7 - 21
ASSEMBLY INSTRUCTIONS
1 10 6 7
3
6
14
15
2
4
5
10
2
13
15
2
10
10 3
16 11
12
3
15
11
3
8
T16000 03/00 8-1

ASSEMBLY INSTRUCTIONS
1 Add some grease to O-ring before assembly.
12 Add some grease to piston rings before assembly slots of piston rings is not allowed to pass bores in
housings
3 Teflon seals must be sized prior to assembly, add some grease to inner and outer dia of clutch drum
before assembly.
4 Pump must be filled up with test oil prior to assembly.
35 Pump drive shaft must be installed after torque converter
36 Fl, Rev, 1st, and 2nd clutch: 9 separator plates with inner splines. 8 friction plates (friction material both
sides) with outer splines, 2 1-side friction plates (friction material 1 side) with outer splines.
Start with one 1-side friction plate, metal against piston, then alternately separator and friction plate.
End with a 1-side friction plate, metal side against end plate or disc spring.
Be sure disc spring is mounted as shown.
- Clearance: Forward low and Reverse: min. clearance = 2,79 mm

(for carbon plates)
max. clearance = 5,21 mm
If clearance is more than 4,79 mm, add one separator plate upon last separator plate.
- Clearance: First and second: min. clearance = 2,54 mm

(for carbon plates)
37 - Fh clutch: 4 separator plates, 3 friction plates and two 1-side friction plates.
- Assembly see 36
- Clearance: min. clearance = 1,24 mm
(for carbon plates)
38 - Disconnect clutch: 12 separator plates, 11 friction plates and two 1-side friction plates.
- Assembly see 36
- Clearance: min. clearance = 3,66 mm
(for carbon plates)
39 CAUTION: Installation force of disc spring is 3280 N !
10
3 Be sure that shielded and sealed bearings are mounted as shown.
11
3 Seals must be pressed in perpendicular upon shaft axis from bearing side. Except lower rear output.
12
3 Plug to be screwed in and torqued but without Loctite.
T16000 03/00 8-2

;;
;
13
3 First clutch springs concave side of first disc spring to be placed against clutch piston wear sleeve.
Remaining 10 springs to be stacked alternately reversed as shown.
14
3 Shipping strap: Only used during shipment of the individual transmission.
;
NOTE: Check if safety valve and valve block are tested before assembly.
15
3 Heat gears up to 150° C (302 F) before assembling.
16
3 Parking brake.
17
3 Mounting: Tighten locking nuts with 0,25 to 1,25 mm clearance between nuts and sleeves.
Adjustment: loosen the (2) adjustment locking nuts (1 and 2). Put lever in correct position.
Tighten inner adjustment nut (2) with 11 Nm. Back off inner adjustment nut (2) with 4 or 5 flats.
;;
Tighten outer locking nut (1) against inner adjustment nut (2).Clearance must be from 0,8 to 1,1 mm.
;;;
;
;;
; ;;;
; ;
1
2
;;;
; ;
;;;
;
T16000 03/00 8-3

Disassembly T16000 transmission
Warning:
For disassembly and reassembly of this unit you will need, besides normal workshop tools and the special
tools mentioned in the last chapter of this manual, a press capable of minimum 20 tons and an induction
heater of minimum 3,5 kW to heat gears up to 150° C (302 F).
T16000 03/00 9-1

Figure 1 Figure 4
Remove oil filter. Remove drive plate screws.
Figure 2 Figure 5
Remove filter adapter screws. Remove drive plates.
Figure 3 Figure 6
Remove filter adapter with O-ring. Remove torque converter as an assembly.
T16000 03/00 9-2

Figure 7 Figure 10
Remove charging pump screws. Remove parking brake mounting screws.
Figure 8 Figure 11
Use a bearing puller to remove charging pump. Remove parking brake as an assembly.
Figure 9 Figure 12
Remove charging pump as an assembly, Remove upper output nut, washer, O-ring and flange.
remove O-ring.
T16000 03/00 9-3

Figure 13 Figure 16
Remove air breather. Remove control valve protection cover and gasket.
Figure 14 Figure 17
Remove control valve protection cover mounting Remove control valve mounting screws.
screws.
Figure 15 Figure 18
Remove wiring connector mounting nut. Remove control valve as an assembly: remove
bypass valve spool and spring in the meantime.
T16000 03/00 9-4

Figure 19 Figure 22
Remove auxiliary pump hole cover screws. Remove pump drive shaft and bearing as an
assembly.
Figure 20 Figure 23
Remove auxiliary pump hole cover and gasket. Remove upper output nut, washer, O-ring and flange.
Figure 21 Figure 24
Remove pump drive shaft rear bearing locating ring. Remove converter housing to transmission case
screws and lockwashers.
T16000 03/00 9-5

Figure 25 Figure 28
Remove transmission case plug. Transmission case removed all drums and shafts
remain in converter housing.
Figure 26 Figure 29
Transmission case plug and gasket removed. Remove transmission case to converter housing
gasket.
Figure 27 Figure 30
Using spreading type snap ring plier, spread ears on Remove output shaft sealing rings.
output shaft rear bearing retaining ring. Holding snap
ring open, tap on output shaft and transmission case T01
to remove case from converter housing. P10-1
Lift transmission case from converter housing
(using lifting bracket).
T16000 03/00 9-6

Figure 31 Figure 34
Remove output shaft rear bearing retaining ring. Using bearing puller to remove 2nd shaft rear
bearing.
Figure 32 Figure 35
Use bearing puller to remove output shaft rear 2nd shaft rear bearing removed.
bearing.
Figure 33 Figure 36
Output shaft rear bearing removed. Using bearing puller to remove input shaft rear
bearing.
T16000 03/00 9-7

Figure 37 Figure 40
Input shaft rear bearing removed. Reverse and 1st shaft rear bearing removed.
Figure 38 Figure 41
Remove reverse and 1st shaft sealing rings. Remove forward low and forward high shaft sealing
rings.
Figure 39 Figure 42
Using bearing puller to remove reverse and 1st shaft Using bearing puller to remove forward low and
rear bearing. forward high shaft rear bearing.
T16000 03/00 9-8

Figure 43 Figure 46
Forward low and forward high shaft rear bearing Remove baffle plates screws, remove baffle plates.
removed.
Figure 44 Figure 47
Use bearing puller to remove forward high gear from Remove oil baffle to converter housing
the input shaft. screws, do not remove oil baffle from output
shaft.
Figure 45 Figure 48
Forward high gear removed. Remove output shaft, 2nd shaft and oil baffle
at the same time.
T16000 03/00 9-9

Figure 49 Figure 52
Loosen suction tube retainer screw. Remove suction tube O-ring and washer.
Figure 50 Figure 53
Remove suction tube retainer screw and lockwasher. Remove output shaft front bearing retainer ring.
Figure 51 Figure 54
Remove suction tube retainer ring. Remove output shaft front assembly.
T16000 03/00 9 - 10
Figure 55
Remove input shaft, reverse and forward
shaft at the same time.
Figure 56
Remove safety valve plug, spring and ball.
Figure 57
Remove by-pass plug, spring and ball.
T16000 03/00 9 - 11
Disassembly forward high clutch
Figure 58 Figure 61
Remove clutch shaft sealing rings. Remove clutch gear.
Figure 59 Figure 62
Remove thrust washer and thrust bearing. Remove clutch gear inner needle bearing.
Figure 60 Figure 63
Remove clutch gear outer needle bearing. Remove thrust washer and thrust bearing.
T16000 03/00 9 - 12
Figure 64 Figure 67
Remove backing plate retaining ring. Remove one outer half disc.
Figure 65 Figure 68
Remove clutch plate spacer. Remove inner and outer discs.
Figure 66 Figure 69
Remove clutch disc backing plate. Remove one outer half disc.
T16000 03/00 9 - 13
Figure 70 Figure 73
Compress spring to remove spring retainer Remove clutch piston spring retainer.
snap ring.
Figure 71 Figure 74
Remove spring retainer snap ring. Remove clutch piston spring.
Figure 72 Figure 75
Remove clutch spring spacer. Remove clutch piston wear plate.
T16000 03/00 9 - 14
Figure 76
Remove clutch piston assembly.
T16000 03/00 9 - 15
Disassembly forward low clutch
Figure 77 Figure 80
Use bearing puller to remove front bearing and gear. Use a bearing puller to remove clutch gear and outer
bearing.
Figure 78 Figure 81
Front bearing and gear removed. Clutch gear and outer bearing removed.
Figure 79 Figure 82
Remove gear retainer ring. Remove spacer snap ring.
T16000 03/00 9 - 16
Figure 83 Figure 86
Remove spacer. Use a bearing puller to remove clutch gear inner
bearing
Figure 84 Figure 87
Remove backing plate retaining ring. Clutch gear inner bearing removed.
Figure 85 Figure 88
T16000 03/00 9 - 17
Figure 89 Figure 92
Remove inner and outer discs. Compress spring to remove spring retainer snap
ring.
Figure 90 Figure 93
Remove one outer half disc. Remove spring retainer snap ring.
Figure 91 Figure 94
Remove clutch gear inner bearing locating ring. Remove clutch piston spring retainer.
T16000 03/00 9 - 18
Figure 95
Remove clutch piston spring.
Figure 96
Remove clutch piston wear plate.
Figure 97
T16000 03/00 9 - 19
Reassembly forward low clutch
Figure 98 Figure 101

Install clutch piston outer seal. Note: Ring must Install clutch piston spring.
be sized before installing in clutch drum. Sizing is best
accomplished by rotating piston while holding a round object
against the new sealing ring. Rotate piston until sealing ring is
flush with outer diameter of piston.

Install clutch piston inner seal. Install clutch piston spring retainer.
Install clutch piston in clutch drum,
use caution as not to damage sealing rings.

Install clutch piston wear plate on piston. Install clutch spring retainer snap ring.
T16000 03/00 9 - 20

Use a sleeve with the proper diameter to fit over shaft Install one outer half disc with friction material down.
and against retainer ring. A sharp blow with a shoft
hammer will compress spring and seat retainer ring.
Be sure ring is in full position in groove.

Install one outer half disc, with friction material away Install backing plate.
from the piston.

Install one steel disc. Alternate friction and steel Install backing plate snap ring.
discs until the proper amount of discs are installed.
First and last discs are steel.
T16000 03/00 9 - 21

Install spacer. Install clutch gear inner bearing.

Install spacer snap ring. Tap inner bearing into place.

Install inner bearing snap ring. Install clutch gear bearing locating rings.
T16000 03/00 9 - 22

Install clutch gear sealing ring. Install clutch gear in Install outer bearing snap ring.
clutch drum. Align splines on clutch gear with internal
teeth of steel discs. Do not force this operation. Gear
splines must be in full position with internal teeth of all
inner discs.

Install clutch gear outer bearing. Warm gear to 150° C (302 F), install gear.
Be sure that bearing shield is on the outside.

Tap outer bearing into place. Warm front bearing to 120° C (248 F), install bearing.
T16000 03/00 9 - 23
Reassembly forward high clutch

Install clutch outer seal. Note: Ring must Install clutch piston return spring.

Install piston inner seal and install clutch Install piston return spring retainer.
piston in clutch drum; use caution as not
to damage sealing rings.

Install clutch piston wear plate on piston. Install spring retainer spacer.
T16000 03/00 9 - 24

Install clutch spring retainer snap ring. Install one steel disc. Alternate friction and steel
discs until the proper amount of discs are installed,
first and last discs are steel.

and against retainer ring. A sharp blow with a soft

Install one outer half disc with friction material away Install backing plate.
from the piston.
T16000 03/00 9 - 25

Install backing plate spacer. Install clutch gear inner needle bearing.

Install backing plate spacer retainer ring. Install clutch gear in clutch drum. Align splines on
clutch gear with internal teeth of steel discs.
Do not force this operation. Gear splines must be in
full position with internal teeth of all inner discs.

Install thrust washer and thrust bearing. Install clutch gear outer needle bearing.
T16000 03/00 9 - 26
Figure 140
Install thrust washer and thrust bearing.
Figure 141
Install clutch shaft sealing rings.
T16000 03/00 9 - 27
Disassembly first clutch

Remove clutch shaft sealing rings. Clutch gear and outer bearing removed.

Remove clutch gear bearing retainer ring. Remove backing plate retainer ring.

Use a bearing puller to remove clutch gear and outer Remove backing plate.
bearing.
T16000 03/00 9 - 28

Remove modulation spring. Remove one outer half disc.

Use bearing puller to remove clutch gear inner Remove inner and outer discs.
bearing.

Clutch gear inner bearing removed. Remove one outer half disc.
T16000 03/00 9 - 29

Compress clutch piston belleville washer spring. Remove clutch piston wear sleeve.
Remove spring snap ring.
Note: Force of disc spring is 3.280N !

Spring retainer ring removed. Remove clutch piston assembly.
Figure 156
Remove disc belleville washer spring.
T16000 03/00 9 - 30
Disassembly reverse clutch

Use a bearing puller to remove gear and front Use a bearing puller to remove clutch gear and
bearing. clutch gear outer bearing.

Gear and front bearing removed. Clutch gear and outer bearing removed.

Remove clutch gear bearing retaining ring. Remove spacer snap ring.
T16000 03/00 9 - 31

Remove spacer. Use a bearing puller to remove clutch gear inner
bearing.

Remove backing plate retaining ring. Clutch gear inner bearing removed.

T16000 03/00 9 - 32

Remove inner and outer discs. Compress spring to remove spring retainer
snap ring.

Remove one outer half disc. Remove spring retainer snap ring.

Remove inner bearing locating ring. Remove clutch piston spring retainer.
T16000 03/00 9 - 33
Figure 177
Remove clutch piston spring.
Figure 178
Remove clutch piston wear plate.
Figure 179
T16000 03/00 9 - 34
Reassembly reverse clutch

Install clutch piston outer seal. Note: Ring must Install clutch piston spring.

Install clutch piston inner seal. Install clutch Install clutch piston spring retainer.
piston in clutch drum, use caution as not to
damage sealing rings.

Install piston wear plate on piston. Install clutch spring retainer snap ring.
T16000 03/00 9 - 35

and against retainer ring. A sharp blow with a soft

Install one outer half disc, with friction material away Install backing plate.
from the piston.

Install one steel disc. Alternate friction and steel Install backing plate snap ring.
T16000 03/00 9 - 36

Install spacer. Install clutch gear inner bearing.

Install spacer snap ring. Tap inner bearing into place.

Install inner bearing snap ring. Install clutch gear bearing locating rings.
T16000 03/00 9 - 37

Install clutch gear sealing ring. Install clutch gear in Install outer bearing snap ring.
clutch drum. Align splines on clutch gear with internal
teeth of steel discs. Do not force this operation. Gear
splines must be in full position with internal teeth of all
inner discs.

Install clutch gear outer bearing. Warm gear to 150° C (302 F), install gear.

Tap outer bearing into place. Warm front bearing to 120° C (248 F), install bearing.
T16000 03/00 9 - 38
Reassembly first clutch

Install clutch piston outer seal. Note: Ring must Install piston return disc springs. First spring with
be sized before installing in clutch drum. Sizing is best large diameter of bevel toward wear sleeve.
accomplished by rotating piston while holding a round object Alternate eleven (11) springs.

Install piston inner seal. Install clutch piston Install disc belleville washer spring retainer ring.
in clutch drum. Use caution as not to damage
sealing rings.

Install clutch piston wear sleeve. Compress spring to install spring retainer ring.
T16000 03/00 9 - 39

Install one outer half disc with friction material away Install modulation spring with large diameter up to
from the piston. the backing plate.

Install one steel disc. Alternate friction and steel Install backing plate.

Install one outer half disc with friction material down. Install backing plate snap ring.
T16000 03/00 9 - 40

Install clutch disc hub inner bearing. Install clutch hub outer bearing.

Tap inner bearing into place. Tap outer bearing into clutch hub.

Install clutch hub bearing locating rings. Install clutch Install outer bearing retaining ring.
gear in clutch drum. Align splines on clutch gear
witch internal teeth of steel discs. Do not force this
operation. Gear splines must be in full position with
internal teeth of all steel discs.
T16000 03/00 9 - 41
Figure 222
Install clutch shaft sealing rings.
T16000 03/00 9 - 42
Disassembly 2nd clutch drum

Press upper output gear from 2nd shaft. Remove clutch shaft sealing rings.

Press gear from 2nd shaft. Use bearing puller to remove clutch hub and front
bearing.

Remove gear retaining ring. Remove clutch shaft front bearing.
T16000 03/00 9 - 43

Remove bearing washer. Remove clutch hub inner bearing.

Remove clutch hub and outer bearing. Remove backing plate snap ring.

Use a bearing puller to remove clutch hub inner Remove backing plate.
bearing.
T16000 03/00 9 - 44

Remove modulation spring. Remove one outer half disc.

Remove one outer half disc. Compress spring to remove spring retaining ring.

Remove inner and outer discs. Remove spring retaining ring.
T16000 03/00 9 - 45

Remove spring retainer. Remove clutch piston assembly.
Figure 242
Remove clutch piston return spring.
Figure 243
Remove piston wear plate.
T16000 03/00 9 - 46
Resassembly 2nd clutch drum

Install piston outer seal. Note: Ring must be Install piston return spring.
sized before installing in clutch drum. Sizing is best

Install clutch piston inner seal. Install spring retainer.
Install clutch piston in clutch drum.
Use caution as not to damage sealing rings.

Install piston wear plate. Install spring retainer snap ring.
T16000 03/00 9 - 47

Use a sleeve with the proper inner diameter to fit over Install one outer half disc with friction material down.
shaft and against retainer ring. A sharp blow with a
soft hammer will compress spring and seat retainer
ring. Be sure ring is in full position in groove.

Install one outer half disc with friction material away Install modulator spring with large diameter up to the
from the piston. backing plate.

Install one steel disc. Alternate friction and steel Install backing plate.
T16000 03/00 9 - 48

Install backing plate retainer ring. Install clutch hub bearing locating rings. Install clutch
gear in clutch drum. Align splines on clutch gear with
internal teeth of steel discs. Do not force this operation.
Gear splines must be in full position with internal teeth of
all steel discs.

Install clutch hub inner bearing. Install clutch hub outer bearing.

Tap clutch gear inner bearing into place. Tap outer bearing into place.
T16000 03/00 9 - 49

Install bearing washer. Install gear retaining ring.

Warm front bearing to 120° C (248 F), install bearing. Warm gear to 150° C (302 F), install gear.

Install clutch shaft sealing rings. Warm upper output gear to 150° C (302 F) install
gear.
T16000 03/00 9 - 50
Disassembly output shaft

Remove oil baffle screws and nuts. Remove output shaft gear retaining ring.

Remove oil baffle. Press output gear from shaft.

Remove output shaft sealing rings. Remove output gear.
T16000 03/00 9 - 51

Remove oil baffle from output shaft. Remove backing plate spacer.

Remove gear retaining ring. Remove backing plate.

Remove backing plate snap ring. Remove one outer half disc.
T16000 03/00 9 - 52

Remove inner and outer discs. Remove spring retaining ring.

Remove one outer half disc. Remove spring retainer.

Compress spring to remove spring retaining ring. Remove clutch piston spring.
T16000 03/00 9 - 53
Figure 287
Remove piston wear plate.
Figure 288
Remove piston assembly.
T16000 03/00 9 - 54
Reassembly output shaft

Install piston outer seal. Note: Ring must be Install clutch piston spring.
sized before installing in clutch drum. Sizing is best

Install clutch piston inner seal. Install spring retainer.
Install clutch piston in clutch drum.
Use caution as not to damage sealing rings.

Install piston wear plate on piston. Install spring retainer snap ring. Use a sleeve with
the proper inner diameter to fit over shaft and against
snap ring. A sharp blow of a soft hammer will
compress spring and seat retainer ring. Be sure ring
is in full position in groove.
T16000 03/00 9 - 55

Install one outer half disc with friction material away Install backing plate.
from the piston.

Install one steel disc. Alternate friction and steel Install backing plate spacer.

Install one half disc with friction material down Install backing plate snap ring.
T16000 03/00 9 - 56

Install oil baffle on output shaft. Install output gear retaining ring.

Install output gear retaining ring. Install output shaft sealing rings.

Warm gear to 150° C (302 F), install gear. Install rear oil baffle on output shaft.
T16000 03/00 9 - 57
Figure 307
Install oil baffle mountng screws, washer
and nuts and tighten nuts to specified
torque (Use Loctite 243).
T16000 03/00 9 - 58
Disassembly disconnect shaft

Use bearing puller to remove disconnect shaft front Remove clutch hub from shaft.
bearing.

Remove front bearing. Remove clutch hub locating ring from shaft.
Figure 310
Remove front bearing retaining ring.
T16000 03/00 9 - 59
Reassembly disconnect shaft

Install bushing if necessary. Install front bearing retaining ring.

Install clutch hub locating ring. Install front bearing on shaft.

Install clutch hub on shaft. Tap bearing on shaft.
T16000 03/00 9 - 60
Disassembly pump drive shaft

Remove rear bearing snap ring. Remove sealing ring from shaft.
Figure 320
Use bearing puller to remove rear bearing.
Figure 321
Remove rear bearing from shaft.
T16000 03/00 9 - 61
Reassembly pump drive shaft

Install sealing ring on shaft. Install rear bearing retainer ring.
Figure 324
Install rear bearing on shaft.
Figure 325
Tap bearing into place.
T16000 03/00 9 - 62
Disassembly input shaft

Remove input shaft rear sealing ring. Remove input shaft front sealing ring.

Remove forward high gear retaining ring. Use bearing puller to remove input shaft front
bearing.

Remove forward low gear retaining ring. Remove input shaft front bearing.
T16000 03/00 9 - 63
Disassembly input shaft
Figure 333
Remove input shaft front bearing retaining ring.
Figure 334
Remove forward low gear retaining ring.
Figure 335
Press forward low gear from shaft.
T16000 03/00 9 - 64
Reassembly input shaft

Install forward low gear retaining ring. Install input shaft front bearing retaining ring.

Warm gear to 150° C (302 F), install gear. Install input shaft front sealing ring.

Install forward low gear retaining ring. Warm input shaft front bearing to 120° C (248 F),
install bearing.
T16000 03/00 9 - 65
Reassembly input shaft
Figure 342
Turn shaft and install input shaft forward high gear
retaining ring.
Figure 343
Install input shaft rear sealing ring.
T16000 03/00 9 - 66
Reassembly converter housing

Install safety valve ball spring and plug. Tap seal into place.

Install by-pass valve ball spring and plug. Install input shaft into housing and in the meantime
install reverse and first shaft (they have to be installed
together). Using caution as not to damage any of the
first shaft sealing rings.

Install output shaft front oil seal. Install forward low shaft and high shaft into housing.
Using caution as not to damage any sealing rings.
T16000 03/00 9 - 67

Install disconnect shaft assembly into housing. Install baffle plate, mounting screws,
washers and nuts. Tighten nuts to specified
torque. (Use Loctite 243).

Open bearing retaining ring. Tap shaft into place. Install baffle plate, mounting screws,
Be sure ring is in groove. washers and nuts. Tighten nuts to specified
torque. (Use Loctite 243).

Install upper and lower output at the same time. Install oil baffle, mounting screws and
Do not force this operation, be sure discs of washers. Tighten screws to specified
disconnect are in full position. Using caution as not to torque. (Use Loctite 243).
damage any of the lower shaft sealing rings.
T16000 03/00 9 - 68

Install O-ring, spacer and snap ring on Install output shaft rear bearing retaining ring.
suction tube. Install suction tube into
housing. Be sure ring is in groove.

Install suction tube retainer, mounting screw and Warm forward high gear to 150° C (302 F),
lockwasher (Use Loctite 243). install gear.

Tighten mounting screw to specified torque. Warm upper output rear bearing to 120° C (248 F),
install bearing.
T16000 03/00 9 - 69

Warm reverse and 1st shaft rear bearing to 120° C Warm lower output shaft rear bearing to 120° C
(248 F), install bearing. (248 F), install bearing.

Warm input shaft rear bearing to 120° C (248 F), Install output shaft rear bearing retaining ring.
install bearing.

Warm forward low and high shaft rear bearing to Install gasket and clutch pressure O-rings (4)
120° C (248 F), install bearing. into O-ring grooves.
T16000 03/00 9 - 70
Reassembly T16000 transmission

Remove lower output bore plug. Position Install transmission case to converter
transmission case on converter housing housing mounting screws and lockwashers.
T01
(using lifting bracket). P10-1 Tighten mounting screws to specified torque.

Using spreading type snap ring pliers, spread ears Using spreading type snap ring plier, spread ears on output
on output shaft rear bearing retaining ring. Holding shaft rear bearing retaining ring. Hold snap ring open, pry or
snap ring open. Tap transmission case into place. lift output shaft. Be sure retaining ring is complete in bearing
groove. (Using a lifting eye or screw M12).

Tap dowel pin in transmission case and converter Install hole plug and gasket.
housing.
T16000 03/00 9 - 71

Tighten plug to 13,6 - 20,3 Nm (10 -15 lbft). Tap seal into place.

Position lower output bore plug and tap bore plug Install upper output flange, O-ring, washer
into place. and nut and tighten nut to 339-407 Nm.
(205-300 lbft).

Position upper output seal. Install pump drive shaft assembly into housing.
T16000 03/00 9 - 72

Install pump drive shaft rear bearing retaining ring. Install pump and O-ring into converter housing.

Install pump hole cover , gasket, screws and Install pump mounting screws and
lockwashers. lockwashers and tighten screws to specified
torque.

Tighten pump hole cover screws to Install convertor assembly on input shaft.
specified torque.
T16000 03/00 9 - 73

Install drive plates on converter. Tighten screws to specified torque.

Install drive plates screws and lockwashers Install oil filter and tighten to 30 - 38 Nm
and tighten screws to specified torque. (22,1 - 28 lbft).

Install filter adapter, O-ring, lockwashers and Instal output shaft front flange, O-ring,
mounting screws. washer and nut. Tighten nut to 339 - 407 Nm
(250 - 300 lbft).
T16000 03/00 9 - 74

Position parking brake , install mounting Position wiring connector in valve protection cover.
screws (See packing brake adjustment).

Install by-pass valve spool into solenoid housing and Install gasket and valve protection cover
spring into transmission case, position control valve mounting screws and tighten screws to
on transmission case. specified torque.

Install control valve mounting screws and Install air breather and tighten to 34 - 41 Nm
lockwashers, tighten screws to specified (25 - 30 lbft).
torque.
T16000 03/00 9 - 75
Figure 398
Install wiring connector nut and tighten to 6 - 8 Nm
(4,4 - 5,9 lbft).
T16000 03/00 9 - 76
SERVICE TOOLS
1. LIFTING BRACKET
10 10
45°
Ø 190 Ø 126
255
"A"
±0,1
57,2
2 Holes Ø13 Ø 10
2 x 30°
±0,1 ±0,1
57,2 57,2
1 7
15
2 15
#TG 1500-676, 1 piece

3 95
Material: ST37
NOTE: Determine measure "A" and weld part 3 after try-out.
+5
R 15 -0
T16000 03/00 10 - 1
Printed in Belgium
Brugge, Belgium
Prepared and printed for SPICER OFF-HIGHWAY PRODUCTS by Brouwer Technisch Bureau

P100 T16000 SM PDF

Uploaded by

Document Informationclick to expand document information

Document Informationclick to expand document information

Copyright:

Available Formats

P100 T16000 SM PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

P100 T16000 SM PDF

Uploaded by

Copyright:

Available Formats

Maintenance and Service Manual

SPICER® OFF HIGHWAY-PRODUCTS™

©Copyright DANA CORPORATION 1990. Unpublished material.

All rights reserved.

Operation of the unit 5

Sectional views and parts identification 7

Disassembly and reassembly of units 9

T16000 03/00 1-1

OIL SEALS, GASKETS, ETC.

GEARS AND SHAFTS

HOUSING, COVERS, ETC.

Smontaggio di sottogruppi Sostituire con ogni montaggio

Montaggio di sottogruppi Togliere - mettere la sicura

Smontaggio di particollari ingombranti Mettere la sicura, incollare (mastice liquido)

Montaggio di particollari ingombranti Evitare danni ai materiali, danni ai pezzi

Attenzione, indicazione importante Marchiari prima dello smontaggio (per il montaggio)

T = Attrezzature speciali P = Pagina Scarricare olio, lubrificante

Rispettare direzione di montaggio Tendere

Controllare esaminare controllo visuale Insere pressione nel circuito idraulico

Eventualimente riutilizzable (sostituire se necessario) Pulire

T16000 03/00 1-2

A. IDENTIFICATION OF THE UNIT

1. Model and type of the unit

B. WEIGHT, DIMENSIONS, OIL CAPACITY

T16000 03/00 2-1

Torque table for bolts.

Torque tables for plugs (o-ring ports)

Torque tables for pipe plugs

T16000 03/00 2-2

D. PRESSURE AND TEMPERATURE SPECIFICATIONS

• Pump flow (*)

• Clutch pressures (*)

T16000 03/00 2-3

• Solenoid (forward reverse, high/low, 2nd/1st, modulation, disconnect)

• Electronic controlled modulation valve :

Tamb Resistance Tamb Resistance

-55 980 50 2417

F. HYDRAULIC COOLER LINES SPECIFICATIONS

• Minimum 19 mm internal diameter for lines and fittings.

• Suitable for operation from ambient to 120° C continuous operating temperature.

• Conform SAE J1019 and SAE J517,100RI.

T16000 03/00 2-4

ATF oil only which meets following specifications:

• Normal drain period:

- Every 1000 hours change oil filter.

T16000 03/00 3-1

C. SERVICING MACHINE AFTER COMPONENTS OVERHAUL

The following are considered the minimum steps to be taken:

1. Drain entire system thoroughly.

T16000 03/00 3-2

D. INSTRUCTIONS FOR LINING REPLACEMENT AND ADJUSTMENT OF PARKING BRAKE ASSEMBLY

T16000 03/00 3-3

(1) DRIVE PLATE AND WELD NUT ASSEMBLY

BOLT CIRCLE DIA. BOLT CIRCLE DIA.

T16000 03/00 4-1

flatness. Measure and record engine crankshaft

flywheel to align a drive plate mounting screw