Sartorius Cubis Series: User Manual

User Manual
Sartorius Cubis® Series

Electronic Semimicro Micro, Precision and Analytical Balances
MSU Models
Contents
Contents
Notes on Using This Manual. . . . . . . . . . . . . . . . . . . . . . 3 Density Determination. . . . . . . . . . . . . . . . . . . . . . . . . 88
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Intended Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Calculation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
General View of the Equipment and Equipment Averaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Supplied . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Formulation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Weighing in Percent . . . . . . . . . . . . . . . . . . . . . . . . . 109
Unpacking the Equipment . . . . . . . . . . . . . . . . . . . . 11 Timer-controlled Functions . . . . . . . . . . . . . . . . . . . . 112
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Totalizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Installation Instructions . . . . . . . . . . . . . . . . . . . . . . 23 DKD Measurement Uncertainty . . . . . . . . . . . . . . . . . 116
Power Connection . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Second Tare Memory (Preset Tare) . . . . . . . . . . . . . . 118
Anti-theft Locking Device. . . . . . . . . . . . . . . . . . . . . 26 Parts Counting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Leveling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Checkweighing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Switching On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Importing/Exporting Data . . . . . . . . . . . . . . . . . . . . . 128
Removing the Retainer with the Display and Calibration and Adjustment . . . . . . . . . . . . . . . . . . . 131
Control Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Calibration/Adjustment Using Internal
Below-balance Weighing . . . . . . . . . . . . . . . . . . . . . 33 Calibration Weight . . . . . . . . . . . . . . . . . . . . . . . . . 131
Cable Opening of the Manual Analytical Balance Calibration/Adjustment Using External
Draft Shield . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Calibration Weight . . . . . . . . . . . . . . . . . . . . . . . . . 132
Moving the Balance . . . . . . . . . . . . . . . . . . . . . . . . . . 37 User Management . . . . . . . . . . . . . . . . . . . . . . . . . . 134
Using the Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 User Management . . . . . . . . . . . . . . . . . . . . . . . . . 134
Turning the Balance On/Off . . . . . . . . . . . . . . . . . . . 38 Creating User Profiles . . . . . . . . . . . . . . . . . . . . . . . 134
Operating Design: Q-Guide. . . . . . . . . . . . . . . . . . . . 38 Activating Users . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Using the Display and Control Unit . . . . . . . . . . . . . . 39 Editing User Profiles. . . . . . . . . . . . . . . . . . . . . . . . 138
Setting the Language . . . . . . . . . . . . . . . . . . . . . . . . 40 Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
Quick Guide: First Weighing . . . . . . . . . . . . . . . . . . . 40 USB Port (PC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
Display in Operating Mode . . . . . . . . . . . . . . . . . . . 41 PS2 Interfaces for Barcode Scanner or Keyboard . . . 142
Display in Setup Mode . . . . . . . . . . . . . . . . . . . . . . . 42 Interfaces (RS-232) 25-pin and 9-pin . . . . . . . . . . . 143
Activating/Switching Users . . . . . . . . . . . . . . . . . . . . 44 Configuring Serial Ports . . . . . . . . . . . . . . . . . . . . . 146
System Settings (Menu) . . . . . . . . . . . . . . . . . . . . . . . 45 Bluetooth® Interface (COM C, Optional) . . . . . . . . . 149
Leveling the Balance (Q-Level) . . . . . . . . . . . . . . . . . 46 Network Interface (Ethernet). . . . . . . . . . . . . . . . . . 151
Calibration/Adjustment Data . . . . . . . . . . . . . . . . . . 47 Data Output. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
Configure Timer Controlled Actions . . . . . . . . . . . . . 48 Data Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
Displaying Device Information . . . . . . . . . . . . . . . . . 50 Updating the Software . . . . . . . . . . . . . . . . . . . . . . . 166
Alibi Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Error and Status Messages . . . . . . . . . . . . . . . . . . . . 168
Device Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . 54 GPL License . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
Task Management . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . 170
Using Applications with the Factory Settings. . . . . . . 68 Storage and Shipping . . . . . . . . . . . . . . . . . . . . . . . . 174
Creating New Tasks (Configuration) . . . . . . . . . . . . . 68 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
Configuring Printouts. . . . . . . . . . . . . . . . . . . . . . . . 71 Technical Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
Combining Applications into One Task . . . . . . . . . . . 77 Balance Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . 197
Executing Tasks . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205
Weighing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 Declarations of Conformity . . . . . . . . . . . . . . . . . . . . 207
Mass Unit Conversion . . . . . . . . . . . . . . . . . . . . . . . . . 80 EC Type-Approval Certificate . . . . . . . . . . . . . . . . . . 209
SQmin Minimum Weighing . . . . . . . . . . . . . . . . . . . . . 83 Plates and Markings . . . . . . . . . . . . . . . . . . . . . . . . . 211
Individual Identifiers . . . . . . . . . . . . . . . . . . . . . . . . . . 85
2 Cubis® MSU User Manual

Notes on Using this Manual
Notes on Using this Manual

t Please read this entire manual carefully and completely before using the device.
t Read the safety precautions carefully.
t This manual is part of the product. Keep it in a safe and easily accessible
location.
t If the manual should be lost or misplaced, please contact Sartorius for
a replacement or download the latest manual from our website:
www.sartorius.com
Symbols and Signs

The following symbols are used in this manual:
2 Warning symbol for various types of dangers.

These symbols are explained in more detail in Section “Safety Instructions.”
h This symbol indicates useful information and tips.
This symbol indicates notes on use of the balance in legal metrology within
the scope of validity of Council Directive No. 2014/31/EU for instruments for which
the conformity assessment procedure has been carried out (Models MS...-.CE...).
H This symbol means that the USER key should be pressed.
D This symbol means that the TASK key should be pressed.
When individual functions are displayed, press the associated softkey.
t Indicates a required action
y Describes the result of an action
1. If a procedure has multiple steps...
2. ... the steps are numbered consecutively.
– Indicates an item in a list
Cubis® MSU User Manual 3

Safety Instructions
Safety Instructions
This device complies with European Council Directives as well as international regulations
and standards for electrical equipment, electromagnetic compatibility, and the stipulated
safety requirements. Improper use or handling can, however, result in damage and/or injury.
This device should only be operated by trained personnel.
Operators must read these installation instructions, particularly the safety information, and
must be familiar with the operation of the equipment. The operator is required to supple-
ment these safety precautions as appropriate. The operating personnel must be provided
with the appropriate training.
The requirements pertaining to applicable installation regulations must be followed when
using electrical equipment in systems and environmental conditions with increased safety
requirements. Relevant laws, standards, regulations, guidelines and environmental protec-
tion laws valid in your country must be observed.
Always keep the equipment and balance freely accessible. Any installation work or balance
operation that does not conform to the instructions will result in forfeiture of all claims
under the manufacturer’s warranty.
Danger of Explosion!
1 Do not use this equipment in hazardous areas in which explosive materials are present.
Danger of Electrical Shock!

If the device is not used in accordance with the instructions, this can affect the product lia-
bility for the device.
2 Make sure that the voltage rating printed on the AC adapter is identical to your local
line voltage. The wall outlet must have a protective grounding conductor. The operating
instructions included with the AC adapter must be followed.
2 Do not switch on the equipment if the AC adapter or power cord are damaged.
If the balance itself, the AC adapter or any cables on the balance are damaged, disconnect
the equipment from the power supply and secure it so that it cannot be turned on.
2 Chemicals (e.g. gases or liquids) that can corrode and damage the inside or outside of the
balance, AC adapter, power cable or peripherals must be kept away from the equipment.
2 Do not operate the balance unless the housing and the display are undamaged and the
housing is closed so that inadvertent contact with parts inside the equipment is not pos-
sible. Make sure that no liquids penetrate the balance and do not allow conductive parts to
touch the balance.
2 Note on Installation:
The operator shall be solely responsible for any modifications to the equipment and for
connecting any cables or equipment not supplied by Sartorius.
Information on operational quality is available upon request from Sartorius.
You should only use peripherals and options supplied by Sartorius.

Safety Instructions
Note on cable quality:

CE conformity is only guaranteed with well shielded cables.
The shielding braid of the cable must be made of metal with at least 80% coverage and also
covered with metal foil as much as possible.
The shielding on both sides on the full metal or metalized connector casing, as well as on
the casing inlet, must be high-frequency compliant and have a flat design.
You can only turn off power to the device by pulling the plug or disconnecting the power
cord, or by unscrewing the four-pin plug at the DC supply cable for the balance.
Do not exert mechanical pressure on the display with sharp objects, as this will damage the
display. Liquid penetration can damage the electrical components.
Only use a lightly-moistened cloth for cleaning. See “Care and Maintenance” for cleaning
the device. Do not compromise the IP protection of the balance.
Do not open the balance housing. If the seal is broken, this will result in forfeiture of all
claims under the manufacturer’s warranty.
The device may only be opened by specialized personnel trained by Sartorius.
Disconnect the balance from the wall outlet prior to moving the device.
Avoid condensation damage to the device. When the balance is turned on, condensation
build-up is not possible. If the device is moved from a cool environment to a warm environ-
ment, you must allow the device to acclimatize for approx. 2 hours before connecting to the
power supply.
Hazards at the Place of Installation and During Operation
3 Avoid generating static electricity and establish equipotential bonding.

A 10 kOhm ground is used when connecting the balance to the power supply. Disconnect-
ing the ground conductor is not permitted.
3 Exercise caution to avoid glass breakage.

There is a danger of lacerations or cuts caused by sharp edges on glass or metal (contact
springs), particularly when removing or replacing the glass draft shield panels; during cleaning;
if a glass sample container breaks, or when modifying the balance hardware configuration.
3 Models with a separate electronics module (e. g. MSU6.6/3.6/2.7), MSU225S/P

and MSU125P:
Do not mix up the electronics module.
Interchanging with, e. g. models of the ME/SE series will damage the device.
3 Make sure all equipment operators have received proper instructions when working with
hazardous or toxic materials.
Failure to follow correct handling procedures can result in breakage of parts or spillage of
liquids or other substances. Make sure the necessary protective clothing or equipment is
worn, such as protective gloves, clothing, eyewear.
All safety regulations applicable in the laboratory must be observed.
3 Exercise caution to avoid squeezing or crushing fingers when

– Operating the electronic draft shield
– Removing or installing the panels
– Adjusting the display
Do not expose the device to aggressive chemical vapors or to unnecessarily extreme tem-
peratures, moisture, shocks, or vibration.
The device should be set up in areas away from equipment or devices that have strong mag-
netic properties. Extreme electromagnetic fields from electrical lines should also be avoided.

Intended Use
Intended Use
Cubis® models are high-resolution balances. They were specially Cubis® models are designed specially for use in research,
developed for exact determination of material mass in liquid, education and day-to-day laboratory tasks in science and
paste, powder or solid form. industry.
Appropriate containers must be used for each type of sample They are designed to be used exclusively indoors.
material.
Specific models cover specific weighing ranges: see Cubis® models can be operated as standalone, connected to
“Technical Data.” a PC, or on a network.
General View of the Equipment and Equipment Supplied

Microbalances: models MSU6.6S, MSU3.6P, MSU2.7S
1
2
19 3
3 4
1 5
6
7
7
8
10
11
12
13
18
Use 6971987
17
16 14
15
Item Description Item Description
1 Weighing pan 12 Female connector for weigh cell

2 Filter weighing pan d 50 mm 13 DC jack
3 Internal draft shield (for MSU2.7S-F only) 14 Display and control unit
4 Optional weighing pan d 75 mm 15 Serial communications port (PERIPHERALS)
5 Shield disk 16 Slot for optional interfaces
6 Optional weighing pan d 90 mm (e.g., 9-pin data output and PS2 or Bluetooth)
7 Shield plate 17 Lug for attaching antitheft locking device
8 Level indicator 18 Weigh cell connector - electronics module
9 Leveling foot 19 Equipotential bonding conductor terminal
10 MSA2.7..model: socket 20 Draft shield
11 Draft shield cover Not shown: AC adapter, USB cable

Models MSU66S, MSU66P, MSU36S, MSU36P
1 2
3
4
5
16
15 6
7
6 8
9
14 10
11
Use 6971987
12
13
1 Push handle/Handle 10 DC jack

2 Inner draft shield 11 Display and control unit
3 Weighing pan 12 Serial communications port (PERIPHERALS)
4 Shield disc 13 Slot for optional interface
5 Level indicator (e. g. 9-pin data output and PS2 or Bluetooth)
6 Leveling foot 14 Connection plug: Weigh cell – electronics module
7 SD card slot 15 Equipotential bonding conductor
8 USB interface for PC connection 16 Lug for attaching anti-theft locking device
9 Weigh cell female connector
Not shown: AC adapter, USB cable

Model MSU116P
2
1
3
4
5
6
16
15
7
8
9
6
10
14 11
Use 6971987
12
13
1 Push handle/Handle 10 DC jack

2 Inner draft shield 11 Display and control unit
3 Weighing pan 12 Serial communications port (PERIPHERALS)
4 Shield disc 13 Slot for optional interface
5 Level indicator (e. g. 9-pin data output and PS2 or Bluetooth)
6 Leveling foot 14 Connection plug: Weigh cell – electronics module
7 SD card slot 15 Equipotential bonding conductor
8 USB interface for PC connection 16 Lug for attaching anti-theft locking device
9 Weigh cell female connector

1
General View of the Equipment
2 and Equipment Supplied
3
4 Analytical and precision balances with a weighing range of up to 15 kg
5 Item Description
6 1 Upper sliding draft shield panel/handle

7 2 Back panel
8
3 Weighing pan
9 4 Pan support (not for MSU225.../MSU125... models)
24 5 Shield plate
22 25 6 Pan retainer
21 7 Right sliding panel/handle
26
8 SD card slot
15 9 Leveling foot
20 17 10 Display
11 Display and control unit
12 Draft shield/Shield disk (only for models
3 with a readability of 1 mg and 10 mg)
4 13 Below-balance weighing port
5 (on the bottom of the balance)
23
6 14 Leveling foot
15 Level indicator
10 16 Power socket
11 17 Slot for attaching an anti-theft device
18 USB socket for a PC connection
19 Below-balance weighing hook
12
20 Slot for optional interfaces,
e.g., 9-pin data output and PS2 (as shown) or Bluetooth
3
21 Communication port (PERIPHERALS) for accessories
5
22 Menu access switch
4 23 Left sliding panel/handle
24 Ethernet interface
6
(on the bottom of the display and control unit)
14 25 Semi-microbalances: Female connector for weigh cell
13 26 Semi-microbalances: Electronics module
11 (for MSU225.../MSU125... models)
3 Not shown:
– AC adapter
4 – USB cable
– Operating instructions
12
14
13
11
22
21 15
16
17
20 18
19


Balances with a weighing range of 20 kg or more
3
4
5
1 DC jack 5 USB socket for a PC connection

2 Leveling foot 6 Display and control unit
3 Level indicator 7 Weighing pan
4 Serial communications port (PERIPHERALS)

Getting Started
Getting Started
Unpacking
Models MSU116P, MSU66S, MSU66P, MSU36S, MSU36P:
t Lift the package containing the device out of the outer packaging by the strap.
t Loosen and remove the strap.
t Remove the cardboard sleeve.

Getting Started
t Remove the following parts from the recessed spaces of the inner packaging:
− Weighing pan
− Shield plate
t Remove the lateral packaging paddings of the inner packaging by pulling out-
ward.
t Remove the retainer securing the front draft shield panel.
t Open the plastic wrapping.
Exercise caution to avoid glass breakage.

Never lift the device by the draft shield panels to remove
it from the packaging.
t Place one hand under the front panel and the other under the back of the
housing and lift the device out of the lower packaging padding.

Getting Started
Do not lift the device by the draft shield or the front panel since
this can result in damage.
t Place the device at the intended installation location.
t Open the draft shield doors.
t Remove the inner foam padding from the draft shield.
Save the box and all parts of the packaging in case it should
become necessary to transport the device. Only the original
packaging provides the best protection for shipment (see also
Shipping on page 36).
Before packing the device for shipping, unplug all connected
cables to prevent unnecessary damage.
Balance with the Analytical Draft Shield
t Open the packaging at the top.
t With both hands in the side impressions lift the balance, with the packaging,
out of the cardboard box.

Getting Started
t Place the packaging with the balance on the floor.
t Remove the top part of the packaging.
t Remove the packages (containing draft shield panels, weighing pan, pan sup-
port, AC adapter, etc.) from the lower packaging and place them to one side.
3 Caution! Exercise caution to avoid glass breakage.

Never lift the device by the draft shield panels to remove it from the
packaging.
t Use both hands to lift the balance out of the packaging.
t Place the balance on an even surface.
Balance with No Draft Shield

t Use both hands to remove the model without a draft shield from the packag-
ing.
t Remove the AC adapter and the balance parts from the packaging.

Getting Started
Assembly
Installing the Analytical Draft Shield Labeled DA, DI, and DU

3
2 t Carefully fit parts onto the balance as shown in the picture.
1 1. Shield plate
2. Pan support (not for MSU225.../MSU125... models)
3. Weighing pan
t Slide the upper draft shield panel into the guide rails from the rear.
t Slide the left and right draft shield panels into the guide rails from the rear.
Make sure the panels are within the upper and lower guide rails.
t Slide the panels in until they engage.
1. Right draft shield panel

2. Left draft shield panel
y This completes the balance assembly.

Getting Started
Installing the Draft Shield Labeled DE for Milligram Balances
3 t Carefully fit all parts as shown.
2 1. Shield plate
2. Pan support
1
3. Weighing pan
Assembly of Milligram Balances without Glass Draft Shield (DR Option)
t Fit all components listed below onto the balance in the order given:
4 1. Pan support (see also next section)
2. Shield plate
3 3. Weighing pan
4. Draft shield frame
2
1 t First insert the shield plate.
t Make sure the pin on the pan support is facing toward the front, and slide it
under the clip on the pan retainer.
1
1. Insert the pan support.
t After inserting the pan support, press it down against the shield plate so that it
2 lies flat.
3 Exercise caution to avoid pinching or crushing fingers.
2. Press down on the pan support
t Place the weighing pan (3) on the pan support.
3
3

Getting Started
t Slide the upper draft shield panel into the guide rails from the rear while
pressing the locking tab.
1 t Slide the side draft shield panel into the guide rails from the rear while pressing
the locking tab.
y This completes the balance assembly.
1 2 t If necessary, remove the panel again:
1. Press on the locking tab

2. Remove the panel
t Place the panel in the storage slot at the back of the balance.
Assembling Precision Balances without a Draft Shield with a Weighing Range of

up to 15 kg
3
2 t Carefully insert all parts.
1 1. Pan support
2. Shield plate/Draft shield
3. Weighing pan
t Place the pan support (1) diagonally and press down lightly.
1

Getting Started
t Carefully turn the pan support clockwise until the two buttons engage.
The pan support is now attached.
t 2. Insert the shield plate/draft shield.

3
t 3. Place the weighing pan on the pan support
2 y This completes the balance assembly.
Balance with the Analytical Draft Shield
t Open the packaging at the top.
t With both hands in the side impressions lift the balance, with the packaging,
out of the cardboard box.

Getting Started
t Place the packaging with the balance on the floor.
t Remove the top part of the packaging.
t Remove the packages (containing draft shield panels, weighing pan, pan sup-
port, AC adapter, etc.) from the lower packaging and place them to one side.
3 Caution! Exercise caution to avoid glass breakage.

Never lift the equipment by the draft shield panels to remove it from the
packaging.
t Use both hands to lift the balance out of the packaging.
t Place the balance on an even surface.
Balance with No Draft Shield

t Use both hands to remove the model without a draft shield from the
packaging.
t Remove the AC adapter and the balance parts from the packaging.

Getting Started
Models with an External Electronics Module: Connecting the Weigh Cell to the
Electronics Module
t Connect the weigh cell and electronics module using the connection cable:
Make sure that the connectors click into place so that both ends engage
correctly.
3 Check the plug contacts to ensure that the connection is correct.

There should be no tension on the connection cable, e.g. if pushed
directly against a wall.
t Connecting the Weigh Cell to the Evaluation Unit:

Make sure that the connector clicks into place so that the cable is engaged.
3 Models with a separate electronics module (e.g. MSU66/36/6.6/3.6/2.7,

MSU225S/P, MSU125P and MSU116P):
Do not mix up the eletronics module.
Interchanging with, e.g. models of the ME/SE series will damage the
device.
Models MSU66 and MSU36: Placing components into weighing chamber
t Insert the following components into the weighing chamber in the order given:
1. Shield disk
2. Weighing pan
3. Internal draft shield
2
1

Getting Started
Model MSU116P: Placing components into the weighing chamber
t Position the support bracket directly behind the front panel.
t Position the glass panel in the retainers and place it at the back of the draft
shield.
t Place the components listed below inside the weighing chamber in the order
given:
1. Shield plate
2. Weighing pan
3 3. Internal draft shield
2
1

Getting Started
MSU6.6S/3.6P/2.7S: Models MSU6.6S/3.6P/2.7S: Placing Components on the Weigh Cell

t Place the following Parts in the order listed:
5 t 1. Shield plate
4 t 2. Shield plate
3 t 3. Weighing pan
Tip:
2 After inserting the weighing pan, turn it slightly to the left and right
1 while pressing it down lightly.
t 4. Internal draft shield (for SE2 only)
t 5. Draft shield: Center the hole over the pan (see arrows).
MSU6.6S-F/2.7S-F: Filter Balances (models MSU6.6S-F/2.7S-F): Placing Components on the

Weigh Cell
t Place the components on the weigh cell in the order given:
t 1. Model MSU2.7S-F: Connector
t 2. Shield plate
t 3. Internal draft shield
t 4. Filter weighing pan d 50 mm or weighing pan

(optional filter weighing pan d 75 mm or d 90 mm)
Note: After inserting the pan, turn it slightly to the left and right,
while pressing it down lightly.
t 5. Draft shield cover
! Notice
Turn the balance off and then on again after replacing the pan during
operation.
Setting up a filter weighing pan for left-handed users:
t Remove the draft shield cover
t Unscrew the pin and move from the right to the left side

Getting Started
t Turn draft shield parts approx. 90 degrees to the left (loosen knurled screw).
Setting the Angle for the Display and Control Unit

The angle of the display unit can be adjusted by the user in order to ensure optimal
readability of the weight values on the display at all times.
t The display and control unit can be tilted as desired.
Choosing a Location
t Selecting the right setup location:

– Set up the device on a stable, even surface that is not exposed to vibrations
(e.g., weighing stone).
– Place the device in a location with enough free space around it so that
excessive heat cannot build up.
– Maintain free access to the device at all times.
– The balance may only be used in closed spaces and at a max. height above
sea level (see, chapter Techn. Data, “Ambient conditions”).
Choose a location that is not subject to the following negative influences:

– Heat (heater or direct sunlight)
– Drafts from open windows, AC systems, and doors
– Extreme vibrations during measurement
– Extreme humidity
For further information, please refer to the “Proper handling of analytical balances
and microbalances” document.

Getting Started
Acclimatization
Condensation from humidity can form on the surfaces of a cold device when it is
brought into a substantially warmer area.
Allow the device to acclimatize for about two hours at room temperature, leaving it
unplugged from the power supply.
°C Carefully read all warnings and safety precautions in the respective section of this
manual.
Power Connection
t Check the voltage rating and plug design.
– Make sure that the voltage rating printed on the manufacturer’s ID label is
identical to that of your local mains voltage.
– If the stated supply voltage or the plug design of the power cord does not
comply with your country’s standard, please inform the nearest Sartorius
representative or your dealer.
– The power must be connected in accordance with the regulations applicable in
your country.
– In order to connect the equipment to the power supply (protection class 1),
use a suitable, correctly installed wall outlet with a protective grounding
conductor (PE) and a fuse of a maximum of 16A.
– Only use original Sartorius AC adapters.
Analytical and precision balances:

1. Plug the DC supply cable of the AC adapter into the power socket of the
balance and tighten the threaded fitting.

Getting Started
Balances with a readability of ) 0.01 mg

1. Plug the DC supply cable of the AC adapter into the power socket of the
electronics module and tighten the threaded fitting.
2. Plug the power cord into the AC adapter.
3. Insert the AC adapter plug into the wall outlet.
y The balance is now ready to use.
Safety Precautions
The output line of the adapter has a terminal (GND) connected to the metal
housing of the balance. The data port is also galvanically linked to the balance
housing (GND).
Connecting Electronic Devices (Peripherals)
t Make absolutely sure that the device is unplugged from the power supply
before connecting/disconnecting any peripheral device (printer, scanner, PC)
to or from the data port.
3 A device connected to the power supply should never be opened.

Getting Started
Anti-Theft Locking Device (Accessory)
Balances with a readability of ) 0.01 mg:

t An anti-theft locking device can be installed to the back of the balance if
required.
Balances with a readability of ) 1 μg:

To fasten the anti-theft locking device, use the lug located on the back of the
weigh cell.
Leveling
R L
h Leveling the balance compensates for slant or unevenness at the
place of installation. The scale must be perfectly horizontal to ensure
consistent, reproducible weighing results. All models are equipped with
an electronic tilt angle detection feature. If the balance is not level, a
R warning message appears on the display.
L Push-button automatic leveling is available on models with motorized
leveling feet. For models with manual leveling feet, please follow the
instructions on the display.
Leveling the Balance Manually

y The scale is leveled using both front leveling feet.
t Screw in both back leveling feet (only for models with back leveling feet).
t Turn the front leveling feet as shown in the illustration until the air bubble is
L R centered within the circle of the level indicator.
y Normally, several leveling steps are required
t Turn both back leveling feet until they touch the setup surface (only for models
with back leveling feet).

Getting Started
Switching On
t Turn on the device via the A key. The following appears on the display:
y You can now follow the brief instructions to configure further necessary
balance settings before beginning weighing operations.
Warm-up Time
12 y To deliver precise results as per the Specifications, the balance must warm up
for at least 30 minutes after initial connection to the power supply. Only then
2 will the device have reached the required operating temperature.
9 3
When a verified balance used in legal metrology (legal-for-trade
applications) is connected to the power, it must warm up for at least
6 two hours before operation.

Getting Started
Modifying the Balance
Setting Up the Display and Control Unit at the Place of Use
The display and control unit can be removed for all models to enable the operator
to customize the work space.
Removing the Retainer with the Display and Control Unit

1
Analytical balances:
2 t Remove all items (such as weights) from the draft shield.
3
t Carefully remove all parts as shown in the illustration.
1. Weighing pan
2. Pan support (not for models MSU225.../MSU125...)
t Keep all parts in a safe place.
t Remove the panels (right and left).
Models with the analytical draft shield:

2. Remove the panel
Models with the milligram draft shield:

2. Remove the panel

1
2 1 2

Getting Started
t Remove the upper draft shield

panel.
2 2 Models with the analytical draft shield

(left illustration):
2. Remove the panel
Models with the milligram draft shield

1
(right figure):
1 2. Remove the panel
t Turn over the balance and place on a soft surface.
3 Exercise caution to avoid breaking the glass on models with a draft shield.
t Use a 2.5 mm Allen wrench to remove the two screws from the display and
control unit retainer bracket.
t Remove the display and re-insert both screws back into their holes.
t Lengthen the cable and position the display and control unit as desired.
t Turn the balance over and place it on an even surface.
t Carefully place all parts on the balance.

3 1. Shield plate/Draft shield
2 2. Pan support (not for models MSU225.../MSU125...)
3. Weighing pan
1

Getting Started
t Replace the upper and side shield panels.

1 1. Upper draft shield panel
2. Right draft shield panel
3. Left draft shield panel
Removing the Display and Control Unit from Precision Balances without a Draft
1 Shield with a Weighing Range of up to 15 kg
2 t Carefully remove all parts as shown in the illustration.
1. Weighing pan
3 2. Shield plate/Draft shield
3. Pan support
t Turn over the balance and place it on a soft surface.
t Remove the two retaining screws.
t Remove the display and re-insert both screws back into their holes.
t Carefully pull the cable connected between the display and control unit from
the retainer.

Getting Started
t Determine the required cable length.
t Return the balance to an upright position and fit the parts onto the balance.
3 1. Attach the pan support

2
2. Shield disk (only for models with a readability of 10 mg)
1
3. Weighing pan
t Level the balance.
Removing the Display and Control Unit from Models with a Weighing Range of
20 kg or more
3 Remove the weighing pan before unscrewing the control unit, so that
the weighing pan does not fall and cause injury.
t Turn over the balance so that the pan side is facing down.
t Remove the two fixing screws using a screwdriver.
t Remove the control unit and re-insert both screws into their holes.
t Carefully remove the connection cable from its holder.
y Longer connection cables should only be installed by a Sartorius technician.

Getting Started
Semi-microbalances: Attaching the Display and Control Unit to the Electronics

Module (MSU225..., MSU125... models)
The display and control unit can also be attached to the electronics module if
required for operation.
Remove the connection cable from the cable channel:

t Remove two screws from beneath the weigh cell and detach the plate.
t Remove the connection cable plug.
t Then reattach the plate to the slot.
t Remove the display and control unit from the weigh cell:
Remove two retaining screws.
t Remove the display and control unit.

Getting Started
t Attach the display and control unit to the electronics module:

Reattach the two retaining screws.
Open the slot for the connection cable on the electronics module:
t Remove the screws from beneath the electronics module and detach the plate.
Connect the display and control unit to the electronics module:

t Plug in the connection cable.
t Then reattach the plate to the slot.
t Slide the cable that sticks out into the cable channel.
Preparing Below-balance Weighing
A port for a below-balance weighing hook is located on the bottom of the balance.
The below-balance weighing port may not be opened or used on

balances used for legal metrology.

Getting Started
Models MSU116P, MSU66S, MSU66P, MSU36S, MSU36P:

t Unscrew cover plate 3 from the bottom of the comparator
t Hang the container with the sample on the notched hook

t Install a draft shield if necessary
t Lift up weighing pan 1

t Unscrew hook 2
t Insert opposite end of hook 2 into port and refasten
t Place weighing pan 1 back on the device
Models MSU6.6S, MSU3.6P, MSU2.7S:

t Remove both screws from beneath the weigh cell and detach the cover plate.
t For example, attach a wire to sample and hang it on the notched hook.
h Install a draft protection shield.
Analytical and Precision Balances with a Weighing Range of up to 15 kg:
1. Remove the hook for below-balance weighing from the bottom of the balance.
1

Getting Started
2. Push the cover of the below-balance weighing port to one side.
3. Carefully screw on the hook for below-balance weighing.
3 Do not screw it in too tightly,

as this could damage the thread or the balance.
t Attach the sample (e.g., using a suspension wire) to the hook.

3
4. When the below-balance weighing has been completed, unscrew the hook and
return it to the clip under the balance.
Balances with a Weighing Range of 20 kg or more:

t Use a suitable screwdriver to unscrew the cover plate from the bottom of the
mass comparator.
t Request the hook directly from Sartorius.
Uninstalling Below-balance Weighing Equipment

t After uninstalling the below-balance weighing equipment, you must close the
opening again with the cover.

Getting Started
Using the Cable Opening of the Draft Shield
Models with an analytical draft shield have an opening for passing a cable
(for example, for a temperature sensor) through to the interior of the weighing
chamber.
1. Lift the locking tab on the rear panel of the analytical draft shield.
2. Lift the panel out of the draft shield.
t Turn the panel clockwise 180° so that the opening is at the bottom.
t Install the desired sensor.
t Insert the panel in the guide rail.
t Lift the locking tab and gently press the panel into position.
t Press the locking tab down and close it.
t You can now begin weighing.

Moving the Balance
Moving the Balance

Transporting the Device over Short Distances
3 Exercise caution to avoid glass breakage.

Never lift and carry the balance by its draft shield.
t Carry as shown in the illustration.
or
t Carry as shown in the illustration.
Storage and Shipping Conditions

– Permitted storage and shipping temperature: -10 to +60°C
– Unpacked devices can lose their precision if subjected to extreme vibrations.
– Excessive vibrations may compromise the safety of the equipment.
Save the packaging for any future storage or shipment of the balance.
Only the original packaging provides optimum protection for the equipment.
– Follow all warnings and safety precautions.
– Chapter: “Storage and Shipping”

Using the Balance
Using the Balance

Turning the Balance On/Off
t Make sure the balance has been installed and put into operation in accordance
with the installation instructions.
A t Press the on/off key A on the control unit.
y The start screen appears briefly on the display, and then the user interface
appears.
h On subsequent starts, the most recently active user profile and task are opened
(if at least one user profile has been set up).
t If prompted, level the balance (see Section “Leveling the Balance” for details).
A t To switch the balance to standby mode or turn it off, press the A key.
t Close the draft shield (if your model has one).
Operating Design: Q-Guide

Cubis® precision and analytical balances are controlled by application software with
interactive operator guidance. Once you open a menu or select an application, brief
instructions appear on the display to guide you through the menu or application
step-by-step. At each step along the way, the display shows only those options that
are relevant to your process; this helps prevent unnecessary “detours” and enables
you to reach your goal more quickly.
This type of user guidance is mostly intuitive. Although operation of the balance
is also mostly intuitive, this manual includes a section with very detailed, step-by-
step instructions where you can learn about all of the available options
(see “Creating User Profiles” in Section “User Management”).
Basic Operational Structure
The most basic functions, weighing and taring, can be carried out as soon
as the balance is switched on. The application software is divided into three general
areas in which individual settings can be configured:
In Task Management (TASK), task profiles with specific applications, weighing set-
tings, and printout settings can be configured.
Simple Weighing
Configured
at factory
D TASK H USER
Task Management (from page 67) User Management (from page 134)
Selecting and starting applications Selecting user profiles
Configuring applications Creating user profiles
Configured
Configuring tasks
by user
System Settings (from page 45)
User Management (USER) lets you set up user profiles with specific configura-
tion settings and user rights. You can also set up password protection to meet your
security requirements. Your balance can also be used without User Management.

Using the Balance
System Settings (MENU) contains all basic settings and parameters which are used
to operate the balance, affect the entire operation of the balance, and can also
be used for creating new tasks.
Wizard
You can choose between two display types in several menus:
The overview lists all parameters with their set options. You can select each individ-
ual option to change its setting.
When you activate the Wizard in the same menu, the program guides you step by
step: The individual parameters with their options are displayed in succession.
Using the Display and Control Unit
Control Keys (Softkeys):
D TASK key: opens Task Management, in which applications can be selected and
tasks defined. While working in this menu, you can also use the TASK key to cancel
at any time and return to task overview.
H USER key: opens User Management, in which user profiles can be selected and
user settings defined. While working in this menu, you can also use the USER key
to cancel at any time and return to user overview.
J TARE keys – left and right: Zero and tare the balance.
If a balance verified for use in legal metrology is unloaded after taring:
A negative gross value marked with a warning symbol appears. To avoid
this: Apply the value of a container, e.g. using the application “Second
tare memory” (see section “Second tare memory (preset tare)”, page 121.
P PRINT key: used to print the currently displayed measurement results

or a user-specific print-out
A On/off key: used to turn on/off and switch to standby
- Softkeys: used to activate the function displayed directly above them
qwe Cursor softkeys: used for navigation on the display
O Operating elements for electronic draft shield (optional)

Using the Balance
Adjusting the Display and Control Unit

The tilt angle of the display and control unit can be set as desired to enable optimal
readability for changing working conditions. The color and brightness of the display
can also be changed to match the illumination in the room.
(see “User Management” and “System Settings”).
SD Memory Card for Data Exchange

The display and control unit is equipped with a slot for an SD memory card where
you can import and export data (tasks, user profiles). Handling the memory card
is explained in Section Importing/Exporting Data.
Setting the Language

y The default language for the display is English.
t To change the language, select Menu and then Lang.
t Use the cursor softkeys to select the desired language.

y The display changes directly to the selected language.
t If you would like to select a language that was not included with the equip-
ment supplied but was later downloaded from the Cubis® website, you must
first import the language file (see Section “Importing/Exporting Data”).
y To display the downloaded language, select the last option in the language list
(“Reloadable language”) and then select the desired language.
Quick Guide: First Weighing

A
t Press the on/off key A to turn on the balance.

J
t Press the tare key J to tare the balance.
The balance is tared, and the displayed value is zero.
y

t If required, open the draft shield and carefully place the sample on the weigh-
ing pan (in a suitable container if required).
t You can read the measured value as soon as the weight value stops changing

and the unit is displayed.

Using the Balance
Display
The display varies depending on whether the application software is in operating
mode or a menu is currently open (setup mode).
Display in Operating Mode

1
7
2 8
3
9
1 Function display: Current task (here: step 1 of 2)

Verified balances feature the 2 Metrology line: Left: weighing capacity (max); right: d = readability (resolu-
following additional displays: tion) of the balance
3 Value range with current measurement value (the numeric value is displayed
In the line for metrological data: in black numbers once the weighing system reaches stability; beforehand it is
Min Minimum weight shown in gray)
e Verification scale interval 4 Status and warning messages (see below)
5 Task area with instructions on how to proceed
In the value range: 6 Functions which are currently available
o calculated values 7 User field: Display of current user, date, and time
k Values < 0 and other values 8 For _.CE model balances verified for use as legal measuring instruments:
pcs Piece count Display of weights that are not weight values, e. g., calculated values
and values < 0
9 Scaled display of measured value (percentage of weighing capacity utilization)
Status and Warning Messages
Tabs with the following messages may be displayed here:

isoCAL: isoCAL is active (extended temperature range)
isoCAL flashes: Calibration required
Level me! flashes: Balance is not level; leveling required
GLP: GLP print is active; header will be printed
[Maintenance] Maintenance: The next scheduled maintenance date has been reached.
SQmin: The entered SQmin value is permanently displayed

SQmin flashes: The weight value is less than the entered SQmin value
U or U* or PA: The selected DKD value (measurement uncertainty)

is currently displayed.
Ion: Ionizer in progress (only if your model has an ionizer)

Using the Balance
Display in Setup Mode

1 5
6
3
1 Interactive area with instructions on how to proceed

2 Orientation line showing your current location
3 Working area with selectable options
4 Toolbar with the available buttons
5 Symbol indicating which menu (TASK, USER, or MENU) is currently open
6 Scroll bar to view entire selection area
Operating the Display Unit
3
Equipment may be damaged by objects with points or sharp edges
(e. g., ballpoint pens).
Use only your fingertips to operate the buttons and softkeys.
q ew The cursor softkeys can be used to navigate to any of the selectable functions
or settings on the display.
w When you reach the desired menu item, press w to confirm your selection.
Alternative selection: When only one out of multiple options is possible, select
the desired option and confirm with w.
Multiple selection: When several options are available, each option will have
a checkbox. To select or deselect an option, highlight it and then press w.
To continue to the next program step, select Next.
If the scroll bar appears on the right edge of the display, there are more options
than are shown on the display. Scroll down with the cursor keys to view all
of the selection options.

Using the Balance
Entering Text and Numbers

A keyboard will appear whenever you have to enter text and numbers.
A cursor appears in the entry line above the keyboard.
t Select the character you would like to insert using the cursor softkeys.
t To accept the character, confirm with Add.
y The character will appear in the entry line.
Press the shift softkey to switch the input mode between uppercase letters,
lowercase letters, numbers, and a complete set of special characters.
Press Add to confirm the selected character and add it to the text line.
The backspace key is used to delete the character to the left of the cursor.
The two arrow keys move the cursor one character to the left or right.
Press OK to exit input mode and save your entry.
Press Back to cancel input mode and go back one program step to the previous
screen.
Opening and closing the rotation draft shield (models MSU6.6S/3.6P/2.7S):
Defining the opening width:

t Touch DraftShld.
yThe settings for the opening angle are displayed.

t Check the settings and change as required.
O Draft shield opens according to the opening angle setting.

Using the Balance
Activating/Switching Users
When the balance is in operating mode, the active user profile is displayed
in the user field at the top right of the screen. To activate another user profile,
open the User Management menu.
H t Press the USER key H.
y T
he user list is displayed. The user profile that is currently active is indicated
by an arrow.
t Select the user profile you would like to activate.
t Confirm your selection with w.
t If password protection is activated, enter your password.
The program switches back to operating mode, with the selected user profile
y
activated.

System Settings (Menu)

This menu contains all balance settings relevant to the device. Basic settings can
be made here that immediately affect the device. Changed settings do not affect
previously defined tasks and user profiles.
h All system settings are applied to all user profiles.
h As long as a task is active and/or a user has been selected, several basic settings
cannot be changed. In order to change all settings, “Weighing” has to be selected
in operating mode and no user profile may be selected.
Not all functions/settings can be selected on balances used as legal measuring

instruments.
t To open System Settings, select Menu when the balance is in operating mode.
y The list of available system settings is displayed.

t Use the cursor softkeys to select the menu item for the settings you would like
to edit.
System settings are divided into the following menus:

– Level the balance
– Calibration/adjustment data
– Configure timer controlled actions
– Device information
– Device parameters
– Import/export data
– Service
You have already learned how to use the menus. In the following, only configura-
tion options are described and explained.

Leveling the Balance (Q-Level)

It is essential for exact weighing results that the balance is absolutely level.
The front leveling feet can be used to level out small tilts in the floor. Depending
on the model, the balance is equipped with either motorized or manually operated
leveling feet.
An integrated sensor detects the alignment of the balance and triggers a warning
message when leveling is required. You can configure this warning message and the
automatic leveling function (see System Settings > Balance Parameters).
When the isoCAL function is activated, the isoCal trigger is set after manual
leveling. Balances with motorized leveling feet are leveled automatically prior to
each new calibration/adjustment.
3 Note: The scale needs to be re-leveled and then adjusted each time its setup
location is changed.
When “Level me!” appears on the display, you must level the balance.
t Make sure that the weighing pan is empty.
t Select the option Level the balance from the menu.
Balance with Motorized Leveling Feet (Available for all models with a weighing
capacity of >61 g and <6200 g):
t To start the leveling function, select Next.
t Follow the instructions on the display.
Balance with Manually Operated Leveling Feet

3 After each leveling routine, the balance must be calibrated/adjusted

(see Section “Calibration and Adjustment”).

Configuring Calibration/Adjustment
Settings are divided into the following submenus:

– Define calibration/adjustment functions
– Define external calibration weights
– Set fully autom. adjustment function isoCAL
t Configure the settings for all submenus.
t To save the settings, select Save.
h Factory settings are marked with an asterisk (*).
Defining Calibration/Adjustment Functions
Cal./adj. key: Function: Block key / *Configure key selection menu / Select
fixed 1-key function
Cal./adj. selection menu: Select which calibration/adjustment functions
are listed when the Cal./adj. key is touched.
Cal./adj. sequence: Options: *Calibrate, then adjust automatically / Calibrate,
then adjust manually
Cal./adj. unit: Options: *Gram / Kilogram / Defined via data record
Defining External Calibration Weights
No. of ext. cal. weights: Enter the number.

Ext. cal. weight n: Enter the data for each calibration weight: weight value
(in grams), ID, certificate, validation
Configuring Fully Automatic Adjustment Function isoCAL
isoCAL: Define the function setting: Off / Show alert levels, manual start /
*On, automatic execution
isoCAL alert level: *isoCAL status field only / Alert message, repeating /
Error message, adjustment required
isoCAL temperature: Enter temperature difference (in Kelvin).
isoCAL interval time: Enter interval time in hours.

Configuring Timer Controlled Actions

You can program the following actions so that they run automatically at preset
times:
– Show message and execute command (see example below)
– Execute command
– Show message (e. g., a prompt as a reminder)
y The available actions are displayed. When you open this menu for the first time,
the list will be empty.
t Select Edit.
t To define a new timer controlled action, select Create.
Later you can also modify, copy, or delete each action here.
Example: You want the “Internal calibration/adjustment” function to run each

morning at 7:00 a.m. In addition, you want a message to be displayed.
t Select the desired action (e. g., “Show message and execute command”).
t Select the command you want to be executed (e. g., “Internal calibration/
adjustment”).

t Enter the text you want to be displayed when the action is being performed
(e. g., “Timer-controlled adjustment”).
t Enter the time when the action should be performed for the first time.
t Define the time interval at which you want the action to be repeated
(e. g., one day for daily occurrence).
t To start the action at the preset time, select Enable action.
Here you can disable the programmed action at any time and re-enable it later with
a new starting time.
y An overview of all settings for the action is displayed.
t Check and correct all settings as required.
t Select Next.
t Enter a name and a description for the action.

t To save the action, select Save.

y The programmed action is displayed in the list of actions.

You can edit them again at any time here.
Displaying Device Information
You can view various information here.

t Select the information that you want to view.
Displaying Basic Information

Here you can find all information about the manufacturer, model, serial number,
host name, and IP address used.
t To view the parameters for SQmin and DKD, select SQminDKD.
t To view the version of the balance, display and control unit, and application
software, select Version.
t To view the weighing ranges and digits (resolution), select Ranges.
Service Information/Hotline
Service contact information is displayed here along with the hotline number
and maintenance contract and interval information.
Calibration/Adjustment Log File

The log file is displayed here with the results of all calibration and adjustment
routines. The older entries are deleted by new entries on a rolling basis.
View Audit Trail

All changes to the menu, user profiles, and task profiles are logged in the audit
trail. These logs will include the following information: user, profile, parameter ID,
parameter, old and new setting. The older entries are deleted by new entries on a
rolling basis. The audit trail can be deactivated via Sartorius Service.

Alibi Memory
The alibi memory contains (stores) weighing results with date, time, and process
number. This takes place every time a print job is requested [e. g., by pressing
Print P]. Tare and input values are also saved. The alibi memory can therefore
be used as a replacement for a log printer.
The data memory has a ring buffer, meaning that the oldest data records can
be overwritten by new ones. The user can define a memory-time dependent
overwrite protection as well a storage period. Standard: 90 days, see Section
“Device Parameters.” The alibi memory can contain approximately 450,000 data
records; storage capacity depends on the size of each data record.
The alibi memory is verifiable. When the balance is calibrated, you must check that
the alibi memory is correctly functioning by saving some values.
If the alibi memory is being used in legal metrology (according to Council Directive
2014/31/EU), the following must be observed:
– Make sure that there is sufficient storage capacity. Responsibility for this lies
with the operator.
– The weighing results should be stored together with a unique ID code (e. g.,
number or date and time). This makes it possible for every weighing opera-
tion or weighing result to be easily assigned and verified if necessary. These ID
codes must be indicated on any receipts generated on peripheral devices.
– All the required tare and net values will be saved during data output.
– It must be possible for the contractual partners involved to be able to check
and verify the stored weighing results.
– Any continuously output weighing results that have not previously been stored
and have no identification codes may only be used for applications that are not
used in legal metrology
(e. g., batching, controlling, or similar). It is not permissible to circulate any
results lacking identification codes for applications used in legal metrology.
– Receipts can be prepared by a peripheral device not subject to legal verifica-
tion in accordance with the preamble to Annex I of Directive 2014/31/EU and
Section 7b (3) 2 of the German Verification Act.
These receipts must contain the following information:
– ID code for every weighing result,
– if used in Germany, a note stating that the weighing results can be com-
pared with the legally stored weighing results using their identification
codes.
You must first install and activate the alibi memory in order to use it (see Device
Parameters > Alibi Memory Configuration).
Searching for and Displaying Data in the Alibi Memory

You can search for data using various search criteria and view the storage capacity
of the alibi memory.

Searching for Data Records by Date
t Select the search function.
y An overview appears on the display.
t Limit the search by selecting the year, month, or day.
t Select Next.
y The desired records are displayed.
t Using the Prev. and Next buttons, you can view more data records from the
selected date.
Searching Data Records by Sequential Number (Data Record Number)
t Select the search function.
t Enter the number for the desired data record.

t Select OK.

y The desired data record appears on the display.
Viewing Information on the Alibi Memory and Available Memory Space
All important status information for the alibi memory is shown here. You can view
the percentage of memory space in use and an estimate of how many data records
can still be stored. The exact number depends on the size of each data record.

Device Parameters
Here you can update the software and change the following device settings.
Settings are applied to all user profiles.
– Configure balance parameters
– Configure data output
– Entering the Device ID
– Set date/time
– Configure display and control unit properties
– Touchscreen adjustment
– Ports
– Alibi memory
– Update software
– Software activation codes (e.g. for “Q-Apps” software options)
– Restoring factory settings
– Motorized draft shield (optional)
– Ionizer (optional)
Configuring Balance Parameters

General Weighing Settings

Here you can configure the default settings for general weighing functions.
These settings can be changed for a specific task whenever a new task is created.
h These settings can only be changed when the balance is set to “Weighing”
in operating mode. If General weighing settings cannot be selected, use
the TASK D button to switch to Task Management and select Weighing.
In order to view detailed information about individual settings, select Info.
Adapt filter: The effects of unfavorable weighing conditions such as drafts or
vibration can be filtered out by adapting the balance filter (and thus its measuring
time) to suit ambient conditions. Options: Very stable conditions / *Stable condi-
tions / Unstable conditions / Very unstable conditions
Application filter: Equalizes the load deviations on the display. Options:
*Final readout / Filling mode / Low filtering / Without filtering
Stability range: The stability indicator lights up when the weighing results are
constant within a set range. Options: Maximal accuracy / High accuracy / *Medium
accuracy / Fast / Very fast / Maximal fast
Stability delay: This setting compensates for slowly abating disturbances, such
as turbulence in the weighing chamber of an analytical balance). Options:
*Very short delay / Short delay / Median delay / Long delay
Zero/tare function: Conditions for performing the tare function.
Options: Without stability / *After stability / At stability
Automatic zeroing: When this option is turned on, the balance is tared auto-
matically when a set fraction of scale intervals per second changes from the display
zero point. Options: On / *Off
Basic unit: Weight unit to be used for this task. Options: Any available weight
unit — the default setting is in grams.
Display accuracy: A lower display accuracy results in a faster display.
Options: *All digits on / Last digit off
Zero/tare at power on: Automatic taring when the balance is switched on.
54 Cubis® MSU User Manual Options: *On / Off
Leveler Configuration (Q-Level)

You can configure the leveling function here.
Leveling Notice
Off, no indication: Leveling prompt is disabled.
Display status: As soon as leveling is required,
Level me! appears and flashes.
Alarm message, leveling required: As soon as leveling is required,
Level me! appears and flashes. If this notice is ignored, an alarm message appears
after five minutes. If this occurs, you can only continue working after the balance
has been leveled.
Automatic Leveling (Balances with Motorized Leveling Feet Only)

Switch off, start with key: Select Start to activate automatic leveling.
Switch on fully automatic: The balance is leveled automatically before every
calibration/adjustment routine.
Power On Mode
t Select the balance’s startup mode for when the balance is switched on or when
the on/off key A is pressed repeatedly.
Options: On/standby or Always on
Power Saving Mode

t Switch the power saving mode of the balance on or off.
Off, no function: Power saving mode is not in use.
Automatic shutoff after 2 minutes: The backlight on the display
and control unit switches off if the device is idle for two minutes.
Restoring Factory Settings

You can reset all balance settings back to the default delivery status here
(after confirming the reset when prompted).

Configuring Data Output (Print Parameters)

Here you can configure all settings for printing and data output.
Several of these settings depend on the interface configuration
(see Section “Interfaces”).
In order to view detailed information about individual settings, select Info.

Printout interface: Options: COM port A, B, C (file/SD memory card), D and
print to file
Protocol: Options: Print / SBI / xBPI / Web services / SICS / Second display.
This setting cannot be changed here; it is defined when configuring the interfaces.
h The parameters and settings that are displayed here depend on the configured
protocol.
GLP printing: When should ISO/GLP printing be allowed? Options:
*Off / For calibration/adjustment only / Always on.
Taring after printing: Automatic tare after print
command. Options: *Off / On
Print event: What event should trigger printing?
Options: *PRINT key / Starting a task / Initialization of an application / Application
result / Printing of component / Result from an application (evaluation of applica-
tion) / End of task / Calibration/adjustment result
Print key elements: Which elements should be printed?
h For further information, please refer to Configuring Printouts in Section

Interfaces.
Entering the Device ID

With these two IDs, you can expand the printer protocol.
t Select the input for both the IDs
t Enter the desired value (text) for each identifier.
t To save settings, touch Save.
Associated input and output commands for data output:

See the chapter Interfaces: SBI Commands, page 164

Setting Date/Time
The date, time, and display format can be set here.
Under Date format:
t Select how the date is displayed and printed out.
− Standard: Language-dependent display format
− DD/MM/YYYY or DD.MM.YYYY: The date is displayed in the order of day,
month, and then year.
− MM/DD/YYYY: The date is displayed in the order of month, day, and then year.
− YYYY-MM-DD: The date is displayed in the order of year, month and then day.
Under Time format:

t Select how the time is displayed and printed out.
− Standard: Language-dependent display format
− HH.MM.SS or HH:MM:SS: The time is displayed in 24-hour format.
− HH.MM.SS on: The time is displayed in 12-hour format. The hours before noon
are displayed with AM, and the hours after noon are displayed with PM.
Configuring Display and Control Unit Properties

The following properties of the display and control unit can be changed as neces-
sary: Language, Background color, Brightness, Acoustic signal.
These general properties are applied to all user profiles, are also used when no user
is logged in, and serve as a template when a new user profile is created.
Configuring Ports and Network Settings)

Here you can configure interfaces (serial ports and network) and settings for
the network.
Also settings for:
– Control inputs/outputs
– Print to file
– FTP server settings
A detailed description of the connection options and data interface ports can
be found in Section Interfaces.

Configuring Serial Ports
y The available ports are displayed.

t Select the port you want to configure.
t Configure all settings for this port.
Configuring Network Ports (Ethernet)
For more information on network operation, see “Network Interface” in Section

Interfaces.
t Select operating mode for the network interface.

No function / xBPI (expanded Sartorius communication / SBI (Sartorius standard
protocol) / Printer output / SICS protocol
t Select connection type.
Server or Client connection
t Configure the local TCP port.
Configuring Network (Ethernet)
t Define the settings for network operation.
The Hostname (device name — max. 24 characters) set here can be printed on logs.
The IP address can be entered and set as a default or obtained automatically.

Control Input/Output (e.g., for Remote Switch)

If you have connected a remote switch, for example, via the peripheral or optional
port, you can define its function here.
t Configure the setting for each port.
t Select the connected hardware device or control function.
h During checkweighing, the control outputs have no function when set to:
– Foot switch YPE01RC
– Control inputs
t Configure the settings for the control inputs and outputs.

Options: Off, no function / TARE key / PRINT key / Cal./Adj. key /
Zeroing / Taring

Configuring “Print to file”
Purpose:
– Transferring a print file in TXT or CSV format to a SD card or FTP server.
– Viewing a print file directly in an Internet Browser.
t Select Off.
t Specify the file format.

Print to CSV file:
In addition to the SBI output (like in the TXT file), three additional columns are also
written to the file: ID, Value and Unit.
The 4 columns are separated by the “;” character. The “+” sign has also been removed
in the third column and the decimal point has been replaced by a decimal comma
(because of Excel).
t To specify the settings for the automatic or manual data transfer, touch Off.
y The data are deleted from the balance after the automatic or manual transfer
so that only the new data are transmitted the next time there is an automatic
transfer.
y Manual transfer:
Touch Trans.SD or Trans.FTP during operation to transfer data to the SD card in
the balance or to the FTP server.
y The transfer takes place in the data/print directory.
t Select the output medium for the file.

y This file can be transferred manually or automatically to the SD card of the FTP
server. Combinations are also possible, e.g. manual transfer to the SD card and
automatic transfer to the FTP server.
“To SD card”:
y When exporting, print files can also be exported to the SD card independent of
the transfer. This will create a copy (backup) of the file to the SD card. This does
not delete the file from the balance. After the export, the files are located in the
directory data/all/EXPORT-xxxx/print.

“To FTP server”:

y If you use the FTP server option for the transfer, the parameters for the FTP server
must be entered in the menu (see next section). The user must have the rights to
create subdirectories on the FTP server.
t Select the desired interval, the date and the time of the first transfer.
t To save settings, touch Save.
Configuring Data Transfer Settings for an FTP Server
t Specify the data transfer settings to a FTP server.
t Enter the following parameters for the FTP server:

IP address, port, FTP user name, FTP password and optionally a subdirectory as
well. The user must have the rights to create directories on the FTP server.
t For more information about displaying a print record via an Internet browser,
go to Interfaces, “Remote Control of the Balance from a PC via Ethernet”
section.

Configuring the Alibi Memory

Here you can switch on the alibi memory, delete the recorded data, and set
the interval for automatic deletion.
t Use the cursor softkeys to navigate through the Device parameters
submenu to Alibi memory configuration.
Alibi Memory On/Off

t Select whether you want to have the alibi memory switched on or off.
Automatic Deletion of Older Data

t Define whether the data stored in the alibi memory should be deleted auto-
matically at regular intervals after a pre-specified time.
t If data should be regularly deleted, enter the desired interval (deletion cycle)
in days.
Reset and Initialize Alibi Memory

You can delete all data from the alibi memory immediately. The settings for the alibi
memory (on/off, deletion cycle) will remain stored.
t To delete data in the alibi memory, confirm deletion when prompted.
Updating the Software

Cubis® software is updated at regular intervals. A detailed description of how
to perform a software update on your balance can be found in Section Updating
the Software.
Restoring Factory Settings

You can reset all settings individually to the factory settings at any time.
t Use the cursor softkeys to navigate through the Device parameters sub-
menu to Restore factory settings.
t Mark any settings you wish to reset and select Next.

t Confirm the reset when prompted.

Motorized Draft Shield (Optional)
O On balances equipped with a motorized draft shield [sometimes called a windshield

(WS)], the control unit has keys on the right and left sides which can be used for the
motor-driven opening and closing of the draft shield doors. You can configure the
functionality of these keys in the menu.
Models with the analytical draft shield: for example, you can configure the left key
to open and close the right and upper door (for users who are right-handed) and
the right key to open and close the left door (for users who are left-handed). The
opening width (entirely or partially) of the sliding panels can also be defined. You
can configure these settings manually on the draft shield itself (see “Learning Func-
tion” below).

t Define the functions for the left and right keys:

Off, no function: The keys have no function.
Same function: Both keys have identical functions.
*Separate function: The left and right keys are configured with different
functions.

Models with a rotation draft shield (MSU6.6S/3.6P/2.7S):
Same function Separate function

(one open position) (two open positions)
Defining the Manually select the –
opening width desired opening position
Touch the O key 1) Open to the previously 1) Touch the left O key:
selected opening Opens 260° clockwise
position Right key O:
2) Close Opens 100° counter clockwise
2) Close
0°
100°
260°
180°

t Configure the automatic mode for the draft shield.

*Off, no function: Automatic mode is off.
Close -> function -> open: The draft shield doors are closed in automatic mode
while the function is executed, and then the doors re-open.
Close > function: The draft shield doors are closed in automatic mode while
the function is executed.
Automatic mode can be executed using the following keys:
– TARE key
– PRINT key
– Cal./Adj. softkey
– or can be executed when a component is saved for logging applications
(statistics, formulation, totalization)
h If automatic mode is on, the draft shield doors automatically close when the
balance is switched to standby.
Assigning Opening Functions to Keys (Learning Function)

The keys should be cross-configured (for example, left key opens and closes right
door and vice versa).
The balance must be turned on.
t Close all draft shield doors.
t Manually operate the door you want to assign to the left key: Push the right
door open to the extent you want it to be opened (entirely or partially).
t Press the left key O.
y The door will close again. Now you have configured the left key so that,
when pressed, it opens or closes the right door.
t Proceed accordingly to configure the left door/right key.
h Using the same method, you can assign operation of the upper door to one
of the keys. You can also configure one key to move both doors by manually
opening both doors during setup and then pressing the desired key.
Configuring the Ionizer (Optional)

If your balance is equipped with an ionizer module, you can configure the basic
settings for the ionizer module here. These settings can be changed as necessary
during any electrostatic charge eliminator task.
t Define ionizer function.

Switch off ionizer: The ionizer is switched off.
Manual activation with [Ion] key: Ionization can be turned
on at any time by pressing the Ion key.
*Automatic execution after closing of ws: Ionization is executed
automatically, as soon as the draft shield is closed.

t Define how long an ionization routine should take.

Operating time in seconds: 3 to 15 sec., *8 sec.
t Define the intensity of the ionization.

Soft intensity / *Normal intensity / Strong intensity


Task Management
Task Management
In the Task Management menu (TASK), you can:
– Start a task
– Configure a new task
– Edit an existing task (modify, copy, delete)
For task configuration, there are numerous applications available, e. g., weighing,
parts counting, calculation. Each task contains at least one of these applications.
However, it can also have a combination of several applications. Each application
can be used either with their factory settings, or you can modify them as desired.
The Weighing application is available as a basic function for every task. Each task
also contains the individual balance settings and the individually configured print-
out.
The options available to you in Task Management depend upon your user access
rights: An Administrator can use all options, while a User can only use limited
options (see “User Management”). If no users have been defined, all options can
be accessed. A maximum of 15 tasks can be created.
The administrator can create tasks with restricted use, i.e., tasks that can only
be used by certain users or only by the administrator himself.
Global tasks can be used by all users.
Separate tasks are only accessible to the users who created them.
Exception: A user can copy global tasks to use them afterwards as a separate task.
Option Administrator User
Configure, modify, delete separate tasks i
Configure, modify, delete global tasks i
Execute or copy separate tasks i
Execute or copy global tasks i i
Selecting Tasks
D t To switch to Task Management, press TASK D.
y A list of available tasks is displayed.
Initially, this overview will be empty. Once tasks have been configured, they will
be displayed here.
t When you touch Start, the task currently selected will be started (indicated
by the dark background).
Importing Tasks:
You can also load preconfigured tasks to the balance:
1) Unpack the desired ZIP archive file to the root directory (Root Dir) of a SD card
after downloading from the Sartorius homepage or from the included CD.
2) In the Balance menu, submenu “Import/Export data:
Import files from the SD card.”
3) Insert the SD card into the balance.
4) Select the corresponding import file and active the task download via Next
. Then exit the menu.
5) Start the loaded task via the selection list.

Task Management
Using Applications with the Factory Settings

Each application comes with specific factory settings.
If you want to apply these settings unchanged, you can do this quickly during
configuration:
D t Open Task Management and select Edit.
t Select Create.
y An application list is displayed.

t Select the application you want to assign to the new task.
t Select Done.
t Enter a name and a description for the task and select Save.
y The new task is saved with the factory settings and displayed in the task list.
Sorting the Task List

New tasks are always added to the end of the task list. After you have configured
several tasks, it may be helpful to sort the task list.
D y The task selection is displayed.
t Select Sort.
y The list is sorted alphabetically (A – Z).
t To reverse the sort order, select Sort again.
t To sort tasks by the date of last use, select Sort again.
Creating New Tasks (Configuration)

The Cubis® software contains the following applications that you can configure
as tasks as required:
– Weighing – Weighing in percent
– Mass unit conversion – Timer-controlled functions
– SQmin minimum weighing (optional) – Totalizing
– Individual identifiers – DKD uncertainty of measurement (optional)
– Density determination – Second tare memory (preset tare)
– Statistics – Parts counting
– Calculation – Checkweighing
– Averaging – Draft shield (optional)
– Formulation – Ionizer (optional)

Task Management
The basic procedure for configuring a task is:

1. Create new task.
2. Select application.
3. Review all of the following prompts and configure your own settings as
required.
4. Perform steps 2 and 3 for additional applications if you would like to combine
multiple applications.
5. Check settings for weighing and printouts and modify as required.
6. If you are an administrator, define whether the new task can be used by all
or only by certain users.
7. Enter a name and description for the new task.
8. Save task.
Create new task
Select application
Review settings
yes
Combine applications?
no
Settings for weighing
Settings for printing
Enter task name/description
Save task

Task Management
Example: Creating a Task

D t Open Task Management and select Edit.
y The list of options is displayed.
t To define a new task, select Create.
y The list of applications is displayed.

t Use the cursor softkeys to view all applications.
t Select the application you want to assign to the new task.
t Configure this application as required. The program guides you through
the configuration menu.
t If you want to assign additional applications to the task, these applications
should also be configured (see “Combining Applications into One Task”).
y After all applications for the new task have been configured, the settings
for weighing and printouts must be configured. All settings configured here
will only affect the new task.
On balances verified for use in legal metrology, the modification of some settings
may be limited or prohibited altogether.
Settings for Weighing

t Check all settings and change as required.
Explanations for the individual options can be found in Device Parameters

in Section System Settings.
t Select Next.
Settings for Printouts

Explanations for the individual options can be found in the following section.
t Select Next.
t Enter a short name and a description for the new task.

t Select Save.
y The task selection list with the new task is displayed.

Task Management
Configuring Printouts
You can configure the printout at two places; for example, you can have the printout
for basic weighing differ from all the other applications.
In the System Settings (Menu) You define the basic settings in the menu. Previously created tasks will not be
affected by modifications to the basic settings.
Creating Tasks This is where you can specifically modify the user-defined settings for any task. You
will be routinely prompted for the printer settings with every new task you create
and can then modify them.
Printout (Example): Print events Printout content (record) Print elements

Start task ------------------ GLP header
21.02.2017 09:17
SARTORIUS
Mod. MSU 224S
Ser. no. 12-34-56
------------------
Start task Laboratory Operator name
e.g. here: technician
Start task Product........... ID1, identification: fixed/variable
P key 123.5678g Measured values

------------------
End task 21.02.2017 09:20 GLP footer
Name:
------------------
Settings for Printouts

During printout configuration the following parameters are defined:
Printout interface Peripheral ports (Com A), USB/PC (Com B), optional interface (Com C), Ethernet
(Com D)
Protocol (operating mode) Depends on the interface: Print, SBI, xBPI, SICS
Output Depends on the operating mode: Single printout or automatic print (not with
printer), with/without stability. For “Autom. Print” for the fasted display result,
set additional software handshake or no handshake.
Printout criterion Manual without stability, manual with stability
Format auto. print 22 characters for applications, 16 characters for raw data
Standard data output Standard 1 (measured value only), Standard 2 (measured value and date/time),
Standard 3 [date/time, weight block (N,T,G), and dotted line]
GLP printing Off, no GLP printout / For calibration/adjustment only / Always on
Print event Defines which event should trigger a print job.
The selectable print events depend on the selected application.
For basic weighing: P key, start or end of task, calibration/adjustment result.
For calculating applications: additional initialization and result.
For logging applications: additional component and evaluation
Print elements The elements to be printed also depend on the selected application. Define the
print elements for each each event, e. g., date and time, dotted line, measured
value, and the sequence in which they should be printed, etc.
Tare after printing: Off, no tare / On (automatic tare after print request)

Task Management
Configuring Printouts in the System Settings (Menu).
h The settings can only be modified as long as no task has been activated (ready to
start) in the operating mode. Make sure that basic weighing is active in the operat-
ing mode.
t Toggle to the System Settings menu.

t Open the Configure data output submenu.
If the submenu is not selectable, check the operating mode and select basic weighing.
y The setting menu will open. Several options are not modifiable because they
are preset by the interface configuration.
The initial default setting and several examples of settings are described in the
following.

Task Management
Standard Printout Parameters When the Balance is First Delivered

When the balance is first delivered, two ports are configured: The peripheral port
(Com A) is configured for one printout; the USB port (Com B) is configured for data
exchange with a PC via SBI protocol.
Printout interface: Com A (peripheral port) and Com B (USB/PC)

Protocol to Com A: Print (preset by the port configuration)
Standard printout to Com A: Standard 1 (measured value only)
GLP printing to Com A: Off, no GLP printout
Print event for output to Com A: Press the PRINT P key
Element to be output via Com A: Measured value
Protocol to Com B: SBI (preset by the port configuration)
SBI output to Com B: Single printout to the PC
Criterion for output to Com B: After stability of balance
Format for output to Com B: 22 characters
Tare after printing: Off, no tare
O t The cursor softkeys can be used to select configurable parameters individually.

or
t To be guided step-by-step through the settings, use the wizard.
Example Manual Printout to Peripheral Port, SBI Operating Mode

y After manual operation, you would like a single printout to be printed by the
connected peripheral device.
Printout interface: Com A (peripheral port)

Protocol: SBI (toggling to port configuration possible)
SBI output: Single printout
Criterion: Manual without stability
Format: 22 characters (for applications)
Tare after printing: On or off
Example Automatic Printout to Peripheral Port, SBI Operating Mode

y At a preset interval, automatic printouts should be sent to the connected
peripheral device.
Interface: Com A (peripheral port)

Protocol: SBI (toggling to port configuration possible)
SBI output: Automatic printout
Criterion: Without stability, at stability, or after weight change
Stop automatic printing: Not possible or by pressing Print P key.
Interval for automatic printing: Number of cycles (1, 2, 5, 10 to100) and 0.1, 0.2,
0.5 to 10 seconds

Task Management
Example Automatic Printout to Peripheral Port, Second Display Operating Mode

y At a preset interval, automatic printouts should be sent to the connected
peripheral device as a second display.

Protocol: Remote display (toggling to port configuration possible)
SBI output: Automatic printout
Criterion: Without stability, at stability, or after weight change
Interval for automatic printing: Display updates (1, 2, 5, 10 to100) or every 0.1, 0.2,
0.5 to 10 seconds
Example Printout to Peripheral Port Only By Pressing the PRINT P Key; Printer
Operating Mode
y After pressing the Print key, the measured value should be printed by the
connected peripheral device.

Protocol: Print (toggling to port configuration possible)
Standard printout: Standard 1 (measured value only), Standard 2 (measured value
and date/time), Standard 3 (measured value with date/time and weight block)
GLP printing: On or off
Print event: Press the PRINT key
Elements for print event PRINT: Measured value PRINT.MEASURE
Tare after printing: On or off
Printout Parameter Settings

Standard Printout
You can select which data should be printed out as default.
Standard 1 (measured value only)
Standard 2 (measured value and date/time)
Standard 3 (measured value with date/time and weight block)
User input is only selectable if the default settings have been modified
by the user.
GLP Printing
You can select if and when the printout should be GLP-compliant.
Off, no GLP printout
For calibration/adjustment only
Always on
User input is only selectable as long as none of the three options apply, i.e.,
if only a GLP header but not a GLP footer has been configured.

Task Management
Print Events
You can define one or several events that trigger a printout.
The number of selectable print events depends on the selected application.
Basic Weighing:
PRINT key
Starting a task
End of task
Calibration/adjustment result, after calibration/adjustment
For calculating applications the following events are also possible:

Initialization of an application
Application result
For logging applications the following events are also available:

Component
Evaluation
The application-specific print events cannot only be configured when a new task
is created and not in the basic menu.
Print Elements
Which information should be printed?
Measured value
GLP header
GLP footer
Space line
Dash line
Form feed
Date and time
etc.
O t The cursor softkeys can be used to select elements individually.

t To view the complete list, select EXTEND.
t To minimize the list, select REDUCE.
Sequence of Print Elements

In which order should the print elements be printed?
y The list of selected print elements is displayed.

You can change the order and duplicate individual elements for multiple printouts
(e. g., at the beginning and end of the list).
t Select the element that you wish to move or duplicate.
t To duplicate the element, select Duplic.
t To move the element downwards in the list, select Down.

Task Management
Automatic Tare after Printing

Should the balance be tared automatically after each printout?
Off, no tare
On (automatic tare after print request)
Settings for SBI Output

SBI Output Mode
How should SBI printout be printed?
Single print: Printout generated by pressing the PRINT P key or by ESC
command via the interface
Automatic print: Printout generated automatically in the weighing cycle
Stability Parameter for Printout

Should the printout be dependent on balance stability?
Manual without stability: Immediate printout without waiting
Manual after stability: Printout generated immediately at stability, otherwise
not until after next stability
Format for Printout

How should the printout be formatted?
For other apps/GLP (22 characters): Printout with header; 20 characters
plus line break (“space line”) (CR) and dotted line (“dash line”) (LF)
For raw data (16 characters): Printout without header; 14 characters plus line
break (CR) and dotted line (LF)

Task Management
Combining Applications into One Task

You can combine applications that are saved in the balance into one
task. The following rules need to be followed (see table below):
– An application can only be combined with applications from different groups.
– You can only combine the applications of the first three groups in the
order given below, e.g., weighing, checkweighing, and totalizing, but not
weighing, totalizing, and checkweighing in that order.
– The applications of the Additional Functions group can be combined freely;
the order is not relevant in this case.
When you combine applications, the Cubis® software automatically suggests only
those applications that follow these rules.
DKD Measurement Uncertainty

Timer-controlled actions
Application group
Density Determination
Mass unit conversion
Second Tare Memory

Individual Identifiers
Weighing in Percent
SQmin function
Checkweighing
Parts Counting
Formulation
Draft Shield
Calculation
Averaging
Totalizing
Weighing
Statistics
Ionizer
Application
Weighing
Density determination z * z z * z z z
applications
Calculating
Calculation z * z z z z * z z z z
Averaging z z z z z z z z z z
Weighing in Percent z * z z z z z * z z z z
Parts Counting z * z z z * z z z z
applica-

Chek-
Timer-controlled actions z z z z z z z z z z
tions
applications king
Checkweighing z z z z z z z z z z z z z
Statistics z z z z z z z z z z z z z z
Logging
Formulation z z z z z z z z
Totalizing z z z z z z z z z z z z
Mass unit conversion z z z z z z z z z z z z z z z z
Additional functions
SQmin function z z * z * * z * z z z z * z z z
Individual Identifiers z z z z z z z z z z z z z z z z
DKD measurement uncertainty z z z * z * * z * z z z * z z z
Second tare memory z z z z z z z z z z z z z z z z
Draft Shield z z z z z z z z z z z z z z z
Ionizer z z z z z z z z z z z z z z z
Weighing is always available

z Combination possible
* Combination possible is only activated as long as no calculating applications
are active.
No combination with identical application possible
No combination with an application of the same group possible
No combination possible because it is not meaningful

Task Management
Executing Tasks
After all required settings have been configured, you can now start and execute
a task.
D t If you haven’t already done so, go to Task Management.
y The task selection is displayed.

t Select the desired task.
or
t If the desired task is already marked (dark background and arrow on left),
select Start.
y The program switches to operating mode and the selected task is activated.

Weighing
Weighing
Purpose: Weight determination within the scope of the device-specific weighing capacity
(see “Technical Data”)
Combination options: Mass unit conversion, second tare memory, and individual identifiers (SQmin
function, DKD measurement uncertainty)
Configuring a Task: My Weighing

D
Weighing without combining with any other application:
y The settings for Weighing are displayed.

t Select Next.
y The settings for Printouts are displayed.
t Select Next.
t If you are an administrator: Define whether all or only certain users may
use this task.
t Select Next.
t Enter a short name and a description for the new task (e.g., “My Weighing”).
t To save the new task, select Save.
Executing a Task: My Weighing

D t If you haven’t already done so, go to Application Management.
or
t If the desired task is already marked, select Start.
y The program switches to the operating mode, and the task is activated.

Mass Unit Conversion

Purpose: The weight value can be displayed in up to a maximum of five different units
in succession (see table below). However, the desired weight units must be assigned
beforehand (1 through 5).
Combination options: Second tare (SQmin function, DKD measurement uncertainty)
Not all units can be selected on balances used for legal metrology.
The user can only switch between metric units (e. g., milligram, gram, kilogram).
This may also depend on the balance model.
Conversion Factors for Weight Units
Unit Factor Display

Gram 1.00000000000 g
Kilogram 0.00100000000 kg
Carat 5.00000000000 ct
Pound 0.00220462260 lb
Ounce 0.03527396200 oz
Troy ounce 0,03215074700 ozt
Hong Kong tael 0.02671725000 tlh
Singapore tael 0.02645544638 tls
Taiwan tael 0.02666666000 tlt
Grain 15.43235835000 GN
Pennyweight 0.64301493100 dwt
Milligram 1000.00000000000 mg
Parts per pound 1.12876677120 /lb
Chinese tael 0.02645547175 tlc
Momme 0.26666666666666667 mom
Carat 5.00000000000 K
Tola 0.08573333810 tol
Baht 0.06578947437 bat
Mesghal 0.21700000000 MS
Ton 0.00000100000 t
Pound: ounce 0.03527396200 lb:oz
Newton 0.00980665000 N
Microgram 1000000.00000000000 μg

Configuring a Task: Mass Unit Conversion

D
t Select the desired number of units (max. 5) to be used to display the weighing
results.
y Now you will be prompted to enter the display accuracy and weight units of
all the desired units one by one.
t Select the Weight unit (e. g., gram, kilogram, carat, pound) for the first unit.
t Select the Display accuracy: (e. g., complete display of all decimal places
or leave off last digit).
y An overview of all settings is displayed.

t Check settings and change as required.
y A message asks whether you would like to add another application.

t If required, select additional applications to be combined.
y Now you will be prompted to configure the weighing and printing functions.

Executing a Task: Mass Unit Conversion

or
t To change the displayed unit, select Toggle.
t Select the unit to be used to display the weighing results.

This setting remains in effect until you change the selection or end the task.
t To display weighing results in all units,

select Toggle.

SQmin Minimum Weighing

Purpose: This application is used to compare the measured weight value directly with the
defined minimum sample quantity (SQmin = sample quantity minimum). This
ensures that weighing results are within tolerances defined by your quality assur-
ance system. This fulfils the requirements of the United States Pharmacopeia (USP).
According to USP guidelines, the measurement uncertainty can be a max. of 0.1%
in terms of the initial weight when weighing substances for quantitative analyses.
Requirements: The balance must be set up by a service technician to be able to use the SQmin
function. The technician will determine the permitted minimum sample quantity
and set this on your balance using your QA system’s guidelines. He will document
this setting via a “Weighing module test as per USP” certificate in which the mea-
surements and min. sample quantity are logged. The SQmin function ensures that
the weighing results correspond to USP guidelines.
Combination options: Mass unit conversion, second tare memory, individual identifiers (DKD measure-
ment uncertainty)
Configuring a Task: SQmin Minimum Weighing

D
t Select which function should be triggered for minimum sample quantity.

SQmin flashing: The SQmin tab flashes.
Disable print/save ...: Printout and saving of the weight value are disabled;
the weight value is displayed in gray.


t If required, select additional applications you would like to combine.

Executing a Task: SQmin Minimum Weighing

or
y W
hen you start a task with the SQmin function, the defined SQmin value
is shown on the display.
y As long as the weight value is lower than the SQmin value, the tab “SQmin”
will flash.

Purpose: You can define identifiers for the following print jobs:
– Printout by pressing PRINT
– Starting a task
– End of task
– Initialization (for calculating applications only)
– Result (for calculating applications only)
– Component (for logging applications only)
– Evaluation (for logging applications only)
These identifiers are also printed in the log (“protocol”).
Example: You want to configure the application as follows:

– You want the printout to be activated with the PRINT key.
– You want to configure the application so that four identifiers are included
in the printed log: your company address in three lines and the batch number
in one line.
– The batch number is to be counted up automatically.
Configuring a Task: Individual Identifiers

D
t Enter the desired number of individual IDs that you want to set up.
Print output: Identifier for the Print p key
Task start, task exit: Number of identifiers for task start or task end.
y The corresponding ID (P-ID1, T-ID1, T-ID2, etc.) will be displayed for each
identifier.
t Enter the desired title for each ID.

y In the example, a unique title has been defined for each identifier.
y Enter the desired value (text) for each identifier .

.
t Select the identifiers that can be entered for executing the task.
t Select whether or not the variable identifiers should be counted up

automatically.
y In the example, the identifier for printout ID1 can be entered and will be counted
up automatically.


Executing a Task: Individual Identifiers

or
y The defined identifiers are displayed (cf. example above).

t Select Next.
y The predefined lines are printed when the task starts:
Company: Sartorius
Street:
Weender Landstr.
City: Goettingen
P t Place the sample on the weighing pan and press the

PRINT key p.
y The identifier for the printout is displayed and can be changed
if necessary.
y In the example, BATCH was defined for the printout.
t If required, you can change this value now.
t Select Next or press the PRINT key p again.
t To log the value, press the Print key p.
y The complete printout looks like this:
Company: Sartorius
Street:
Weender Landstr.
City: Goettingen
N + 214.5 g
BATCH 1
N + 213.3 g
BATCH 2

Purpose: You can determine the density and volume of liquid, solid, or pasty materials.
Combination options: Checkweighing, statistics, second tare, or individual identifiers
Requirements: You require the Sartorius YDK01MS density determination kit or your own
customer-specific set. The basic calculations for density determination are described
at the end of this section.
Features * = Factory setting

Liquid
*Water: For density determination using water; the density for the corresponding
temperature is calculated automatically
Ethanol: For density determination using ethanol; the density for the corresponding
temperature is calculated automatically
User input: For density determination using another liquid, enter liquid and its density for
corresponding temperature
Density at 20°C/68°F and exp. coefficient: For density determination using another liquid, enter density at 20°C and the
coefficients of expansion; the density for the corresponding temperature is calcu-
lated automatically.
Air Density
*Air density at 20°: For measurement under standard laboratory conditions
User input: For measurement under other conditions, enter air density
Decimal Places
No decimal place: The measurement value is displayed without decimal places.
1, *2, 3, or 4 decimal places: The measurement value is displayed with the selected number of decimal places.
You can choose from four methods for density determination:

– Determine density of liquid (with glass plummet)
– Determine density via buoyancy with Sartorius YDK01MS density determination
kit (for solid samples)
– Determine density via displacement (for solid samples)
– Determine density via pycnometer (for liquid, pasty, and powder samples)

Configuring a Task: Determining the Density of a Solid
You can choose from two methods to determine the density of a solid: buoyancy
or displacement.
D
t Select the method that you want to use: buoyancy or displacement.
t Select the density kit you want to use.

YDK-xxx density kit from Sartorius: For measuring with the YDK kit
Other density kit: If you want to use another kit
No density kit: If you do not want to use any kit.
t Select or enter the prompted values (for explanations see Features on page 66).
Additional Prompts/Settings for Other Density Kits

* = Factory setting
Parameters for the density kit
Name: Enter a name.
Number of wires: Enter the number of wires for the density kit that are immersed into the liquid.
Wire diameter: Enter wire diameter (in mm).
Vessel diameter: Enter vessel diameter (in mm).
Configuring a Task: Determining Density Using a Pycnometer

D
t Select the Pycnometer method.

t Select or enter the prompted values (for explanations see Features on page 66).

Configuring a Task: Determining Density of Liquid

D
t Select Determine density of liquid.
t Select the measurement conditions.

Air density at 20°: Measurement takes place under standard laboratory
conditions (20°C room and material temperature).
User input: If the measurement is to take place under deviating conditions.
t Enter the required values.
t Enter the volume of the glass plummet.
t Select the number of decimal places to be used for the density results.

t Check all settings in the overview and change individual parameters as required.

Executing a Task: Density Determination
t Prepare the density determination kit that you want to use.

or
y The program switches to operating mode.


Calculation Basis for Density Determination

The density determination application is based on the equations:
Rho Density of sample (l)
lfl Density of buoyancy liquid
Wa Weight of sample in air
Wfl Weight of sample in liquid (when determining liquid density, buoyancy
and displacement)
Weight of fill medium (for pycnometer)
Wr Weight of sample and fill medium (for pycnometer)
LA Air buoyancy correction = 0.0012 g/ccm
Buoyancy: Rho = (Wa * (lfl - LA)) / ((Wa - Wfl) * corr) + LA
Displacement: Rho = (Wa * (lfl - LA)) / (Wfl * corr) + LA
When the displacement method is used to correct for buoyancy by means of a wire
(string) suspended in liquid, the factor 1.00000 is used in the calculation as
a factory-set default.
The correction factor Corr is calculated from: Corr = 1 - n * d2 / D2

with:
n Number of wires
d Wire diameter (YKD01MS: 0.7 mm)
D Inner diameter of the vessel being used (YKD01MS: 76 mm)
When other vessels or other submersion assemblies are used, this factor can
be changed by modifying the parameters for the density kit.

Statistics
Statistics
Purpose: Saving and statistical analysis of weight values and other calculated values.
The values are generated as results:
– Transaction counter
– Sum of all values
– Average value
– Standard deviation
– Lowest value (minimum)
– Highest value (maximum)
– Difference between maximum and minimum
Options: You can save a maximum of 65,535 components.
Combination options: Density determination, calculation, averaging, weighing in percent, parts count-
ing, timer-controlled functions, checkweighing, mass unit conversion, second tare
memory, individual identifiers (SQmin function, DKD measurement uncertainty)
Configuring a Task: Statistics

D
* = Factory setting
t Define how the weight value will be applied.

*Manually: The weight value is applied as soon as the corresponding button
is touched.
Automatically: first value at stability: The weight value is applied auto-
matically as soon as the balance has stabilized after filling and the value exceeds
the minimum load.
Automatically: last value at stability: The last weight value with stabil-
ity is applied automatically, as soon as the balance is unloaded and the value falls
short of the minimum load. If stability was reached repeatedly between measure-
ments, the last stable weight value will be stored.
You must now select the minimum load to be applied:
(none, 10, 20, ...*100 ... 1000 digits).
Weighing Mode with Automatic Storage:

t Select the weighing mode to be used for the weight values. Weighing in:
Initial weighing of samples in a container.
Final readout: Final weighing of samples in a container.

Statistics
t Define when the number of measurements (items) will be set.

Enter fixed quantity: The item number is defined beforehand.
Quantity can be changed during the process: Enter the item number
when you execute the task.
t Define whether or not automatic taring should take place after storing the
value.


y The new task is saved with your settings and displayed in the task list.
Executing a Task: Statistics

or
t If the desired task is already selected, press Start.
y The program switches to operating mode.
t If required, enter the number of items that you want to analyze.

t Place the first sample on the weighing pan.
t To start Statistics, select Start.
y The first weight value is displayed.

Statistics
t Place the next sample on the weighing pan and select Next.
t Continue with all other samples in the same way.
t You can remove each last value from the statistics by selecting Corr.
t During the task, you view the result at any time by selecting Calc.
y Once all intended samples have been weighed, the result is displayed.
t To delete the results and begin the next task, select Clear.
Print example:
---------------------
n 1
Comp 98.8 g
n 2
Comp 56.4 g
:
:
:
n 5
Comp 56.4 g
n 5
Sum 280.3 g
x 56.06 g
s 24.93 g
sRel 44.46 %
Max 98.8 g
Min 37.2 g
Diff 61.6 g
---------------------

Calculation
Calculation
Purpose: This application is used to calculate the weight value using an algebraic formula
that you define yourself. You can define a fixed formula or one that you can
change while carrying out the task.
For balances used in legal metrology, follow the directions in Section “Executing
Tasks.”
Example: You want to determine the area of irregularly cut pieces of paper. The weight per
unit area of the respective paper type is known.
Configuring a Task: Calculation

D
t Select whether you want to use a fixed formula or a variable formula.

Enter fixed formula: All calculations are carried out with the formula that
you define for this task.
Formula can be changed during process: You can change the formula
before each calculation.
Example: The area of irregular paper samples must be determined.

The paper’s weight per unit area in g/cm2 is known. The equation for determining
the paper area in cm2 is:
Paper area = weight value W in g * 10000 / weight per unit area in g/cm2.
The formula to be entered for a weight per unit area of 80 g/cm2 is:
Wx10000/80
To analyze different paper types, the formula must be able to be changed before
each calculation (e.g., for paper with 80, 90, 100 g/cm2).
Additional formula examples are at the end of this section. Likewise, you can create
several tasks, one for each paper type.
t If a fixed formula will be used, enter it now.

t If you want to work with a variable formula, enter the formula when you carry
out the task.
Dynamic weight value Pi = 3.1415926
Applied weight value* a Applied weight value* b
Fixed constant
calculated value
Square root**
Second power**
Third power**
* for calculation
** corresponding to general mathematical characters

Calculation
t Enter a name for the event printout, e. g., “Area” (max. 6 characters).
t Define how many decimal points should be used for the results:
none, *1 ... 7 digits
t Enter the unit to be used for the results

(max. six characters, e.g., cm2)


Calculation
Examples of Calculation Formulae

1) Determination of diameter for cylindrical bodies
Definition: Diameter = 2 * V (W / (/ * l * Rho))
with: V = Square root
W = weight value in g
/ = 3.145
l = length of sample in cm
Rho = density of sample in g/cm3 (e.g., 8.30000 g/cm3)
Input: 2 + V (W/(/ + 100 + 8.3))
2) Determination of mass
1. Definition: m=W*K
with: m = Mass of sample
W = Weight value
K = Correction factor
2. Definition: K = 1 - (RhoL / RhoST) / 1 - (RhoL / RhoG)

with: RhoL = Air density (kg/m3), e.g., 1.2 kg/m3
RhoST = Density of steel (8000.00000 kg/m3)
RhoG = Density of sample (e.g., 2.4000 g/cm3 = 2400 kg/m3)
Input: W + ((1-(1.2/8000))/1-(1.2/2400)
3) Air density determination with YSS45 air density kit

mA * WST - mST * WA
RhoL = ____________________________
mA * WST mST * WA
_________ - __________
RhoA * 1000.0 RhoST * 1000.0
with:
RhoL = Air density[kg/m3]
RhoA = Aluminum density [kg/m3] RhoST = Steel density [kg/m3]
mA = Mass of aluminum mST = Mass of steel
WA = Measured value for aluminum WST = Measured value for steel
Input: ((X + Wa)-(Y + Wb))/(((X + Wa)/(2.72762 + 1000))-((Y + Wb)/(7.84231 + 1000)))

Calculation
Executing a Task: Calculation

or
t If you want to work with a variable formula, you can now enter or change
the formula.
t Place the sample on the balance.
y The weight value is displayed.

t To start the calculation, select Start.
y The calculation results are displayed.

t To return to the weight value display, select Weigh.
t If you want to carry out additional weighing and calculations using the same
formula, place the sample on the balance and then select Calc.
t If you want to carry out additional weighing using a different formula, select
Back.
t You can now change the formula and then proceed as described above.

Averaging
Averaging
Purpose: This application is used for moving samples (e. g., live animals) and for weighing
in unstable environments. A measurement cycle is automatically carried out with
a defined number of measurements for each object to be weighed. The individual
measurements are averaged, and this average is displayed as the result.
For balances used in legal metrology, follow the directions in Section “Executing
Tasks.”
Options: You can start the measurement manually or it can start automatically as soon as
the min. weight is reached. Depending on how strong the unsteadiness of the
sample is, you can vary the sensitivity for the measurement. The number of
measurements from which the average is taken can also be defined.
Combination options: Checkweighing, timer-controlled functions, totalizing, statistics, formulation,
SQmin function, DKD measurement uncertainty, second tare, individual identifiers
D Configuring a Task: Averaging
t Select how the application should start.

Start by pressing key: This starts the application manually.
*Automatic start: The application starts as soon as a pre-defined
min. load is exceeded.
t Define the min. load for the automatic start of the averaging and/or for
the release of the result display for the manual start.
none, 10, 20, 50, *100, ...1000 digits
The number of digits depends on the balance resolution (see Display).

Example: For a balance with a resolution of d = 0.1 (100 mg), 100 digits means
a min. load of 100 + 0.1 = 10 g. With this setting, the automatic start would
be triggered as soon as a min. of 10 g was placed on the balance.
Automatic start only:

t Determine the weighing mode: *Weighing in or Final readout

Averaging
t Enter the range of instability for the start of the measurement:

0.1%, 0.2%, 0.5% ... *10% ... 50% from measured object
This entry estimates the strength of the instability that is caused by the activity
(e. g., animal movement). You can use the rough estimation or a more detailed
estimation using percentages.
The weight value changes with each movement of the weighing pan. As soon
as three consecutive measurement values are within the selected instability range,
the interval measurement begins.
Example: You are weighing animals with an average weight of approx. 300 g.

With the “5.0% of object” setting, the measurement starts when the movements
are within a range of 15 g, i.e., ± 7.5 g. With the “50% of object” setting, the
interval measurement would start when the weight value was within a range
of 150 g, i.e. ± 75 g.

Activity
Measurement at 50% ±75 g Measurement at 5% ±7.5 g
400
350
300
250
Digits
200
150
100
50
0
Time
Start at minimum load 100 digits
t Define the number of measurements to be used for the average value.

Enter fixed number: You must now enter a fixed number.
*Number can be changed during process: You will define the number when
you execute the task.

Averaging
t Define whether or not the weighing results should be calculated with an

additional factor and how this factor should be applied.
No factor
Enter fixed factor: You must now enter this factor.
Factor can be changed during process: You must enter this factor when
you execute the task.
Example: Each animal should receive a food supplement of 50 mg per kg of body

weight. For this, the factor 0.05 can be entered (weight value in g/1000 g + 0.05 g).
During the measurement, both the weight value (animal weight, e.g., 285 g) as well
as the calculated value (amount of supplement, e.g., 14.25 mg) can be displayed.
If you chose to conduct the calculation:

t Define the number of decimal places to be used for the calculation.
none, 1, *2, ... 6 digits
t Define whether or not the end of the measurement (and if necessary the
calculation) should have an acoustic signal.
*Result beep, off or Result beep, on



Averaging
Executing a Task: Averaging with Manual Start

or
t If you are using a variable number of measurements, enter the desired number.
t If you are weighing live animals, place the container (cage) on the weighing
pan and tare the balance.
t Place the animal in the container.
t To begin weighing, select Start.
y The defined number of measurements is carried out and the average

is displayed.
t To start the calculation, select Start.
y The results calculated with the entered factor are displayed.
t To display the average weight value, select Result.
t To view the calculated value on the display again, select Calc.

Averaging
Executing a Task: Averaging with Automatic Start

or
t If you are using a variable number of measurements, enter the desired number.
t If you are weighing live animals, place the container (cage) on the weighing
pan and tare the balance.
t Press Start to begin the task.
t Place the animal in the container.
y The measurement starts automatically; the defined number of measurements

and averaging is carried out.
y The calculated results are displayed.
t To display the average weight value, select Result.
t To view the calculated value on the display again, select Calc.

Formulation
Formulation
Purpose: This application is used to weigh while adding several components consecutively.
The balance is tared automatically after each component. The weight values of all
individual components as well as the total weighing results are recorded and can be
logged. You can save a maximum of 65,535 components.
Combination options: Mass unit conversion, second tare memory and individual identifiers (SQmin
function, DKD measurement uncertainty)
Options: The program allows seven different formulations.
1) Fixed formulation in grams: Number of components and the weight portion

of each component (in g) are fixed.
2) Fixed formulation in % with total = 100%, total weight is entered: Number

of components and the percentage of each component (in g) are fixed. The total
weight is entered when the task is started. If the percentages do not add up to 100,
the individual values are converted to 100%.
Example: Number of components nDef =3; component 1 = 25%, component 2 =
30%, component 3 = 10%; components, total = 65% is set equal to 100%.
Component 1: 25%/65% * 100 = 38.46%; Component 2: 30%/65% * 100 = 46.15%;
Component 3: 10%/65% * 100 = 15,38%
3) Fixed formulation in % with total = 100%, total weight is calculated accord-

ing to the first component: Number of components and the percentage of each
component (in g) are fixed. If the percentages do not add up to 100, the individual
values are converted to 100% (cf. Formulation 2) After weighing the first compo-
nent, the total weight (100%) is calculated.
4) Fixed formulation in % with total <> 100%, total weight is entered: Number
of components and the percentage of each component (in g) are fixed. If the total
of percentages does not equal 100, the individual values are not converted. The
total weight is entered, for each component, the user-defined weight and the per-
centage are displayed before weighing.
5) Fixed formulation in % with total = 100%, total weight is calculated accord-

ing to the first component: Number of components and the percentage of each
component (in g) are fixed. If the percentages do not add up to 100, the individual
values are converted to 100%. For the first component, the user-defined weight
is displayed before weighing in percent. After weighing the first component,
the total weight (100%) is calculated. Before weighing any other component,
the respective user-defined weight is displayed in g and %.
6) Variable formulation in grams, component count are in a fixed order:

Before weighing the first component, you can change the number of components;
before weighing each component you can change its name.
7) Variable formulation in grams, component count are in a fixed order:

Before weighing the first component, you can zero the number of components;
before weighing each component you can change its name.

Formulation
For all formulations, the following applies:

– The individual components can be stored manually or automatically
(first reproducible value).
– If automatic storage of values was selected, the minimum load is determined
when the task is created.
– After weighing the first component, the Calc. option is displayed. That way,
you can change the display to show the intermediate result.
– Once the intermediate result is displayed, you can delete the value of the last
weighed component by selecting
Corr. and it will be removed from the calculation. This allows you to delete
all components step-by-step in reverse order. Deletion is irreversible!
– Use Back to toggle the display and continue the task.
– After the defined number of components has been weighed, the evaluation
is displayed. Here too, you can still delete the components (beginning with
the last component) and weigh them again.
Note: For the seventh formulation, there is no automatic evaluation because
the defined number of components is zero. You have to evaluate the measurement
manually by selecting Calc.
Configuring a Task: Formulation

D
* = factory setting
t Define how the weight values will be applied.
*Manually: The weight value is applied as soon as the corresponding softkey

is pressed.
matically as soon as the balance has stabilized. You must now select the minimum
load to be applied (10, 20, ... *100 ... 1000 digits).
t Set when the number of components will be defined.
Enter fixed quantity: The number of components is defined beforehand.

*Quantity can be changed during process: Enter the number of compo-
nents only when you execute the task (Formulations 6 and 7).

Formulation
t Once you configure the components, define the unit:

*Amount in weight unit (Formulation 1)
Default in percent, sum = 100% (Formulations 2 and 3)
Default in percent, sum <> 100% (Formulations 4 and 5)
t Select Next.
t Enter the number of components.
y An overview of all settings is displayed (here, Formulation 2 as an example).


Executing a Task: Formulation

or
t If required, enter the number of components that you want to weigh while
adding them.
t To start the formulation, select Start.
t If required, enter the name of components.
Please note that you will be able to scroll through the lines with the cursor softkeys
as soon as a scroll bar appears to the right of the display.

Formulation
y The evaluation is displayed as soon as all components of the formulation have

been added and weighed.
You can also see the complete list here using the cursorsoftkeys.
t To delete the last component, select Corr.
t To go to the parameter page, select Param.
t To restart the formulation (with changed parameters), select Start.
Print example:
---------------------
IdCm1 Component1
Comp1 + 39.2 g
IdCm2 Component2
Comp2 + 23.3 g
:
:
:
IdCm5 Component5
Comp5 + 32.4 g
nDef 5
Sum + 117.6 g
---------------------

Weighing in Percent
Weighing in Percent
Purpose: This application is used to determine the percentage share or the percentage
difference of the sample related to a reference weight.
Options: You can enter a fixed reference weight or a reference percentage.
second tare, individual identifiers (SQmin function, DKD measurement uncertainty)
Configuring a Task: Weighing in Percent
t Define how the weighing in percent will be initiated.

*By calculating reference weight: The reference weight is determined
by weighing a reference object.
By entering reference weight: The reference weight is entered as a numeri-
cal value.
If the reference weight should be calculated:

t Define whether the reference percentage should be fixed or variable.
Enter fixed reference percentage: You must now enter this.
*Reference percentage can be changed during process: You can enter
this when carrying out the task.
If the reference weight should be fixed:

Enter fixed reference weight: You must enter this now.
*Reference weight can be changed during process: You can enter this
when carrying out the task.

Weighing in Percent
t Define which percent calculation should be used.

Example: Weight value = 10 g, reference weight = 50 g
*Residue: The result is the percentage share of the weight value of the reference
weight (residue: weight value / reference weight * 100%; in this example: 20%)
Loss: The result is the percentage loss between the weight value and the reference
weight (loss: weight value - reference weight / reference weight * 100%; in this
example: -80%)
Ratio 1 (DR): The result is the percentage ratio of the difference to the weight
value (ratio 1: reference weight - weight value / weight value * 100%; in this
example: 400%)
Ratio 2 (OR): The result is the percentage ratio of the reference weight to the
weight value (ratio 2: reference weight / weight value * 100%; in the example:
500%)
t Define the number of decimal places to be used for the display of the
percentage.
none ... 1, *2 , 3, 4
t Define the accuracy to be used to store the weight value for the reference
weight.
*Normal resolution (display)
10-fold (+ 1 dec. place)
100-fold (+2 dec. places)



Weighing in Percent
Executing a Task: Weighing in Percent

or
t If required, enter the reference percentage (e. g., 100%) or the reference weight.
t Place the sample on the weighing pan.
In the example it is the reference sample.
y The weight value of the reference is displayed.

t To start weighing in percent, select Start.
y The values for the reference percentage and the reference weight are displayed.
t Place the next sample on the weighing pan and select Weigh.
y The weight value is displayed.

t To toggle between the display of weight and percent, select Percent
or Weigh.

Timer-controlled Functions
Purpose: This application is used to trigger individual balance functions automatically
at a specific time or after specific time intervals. The trigger time or interval must
occur within 24 hours (1 day).
Options: You can select the following functions:
- Acoustic signal
- Hold display (freeze)
- Automatic printout of the display value
- Transfer of components for totalizing, formulation, or statistics
Example: In order to determine the amount of evaporation of a sample over time, you can
place the sample on the weighing pan and print out the weight value at fixed
intervals (e. g., every two minutes).
Combination options: Totalizing, statistics, formulation, mass unit conversion, second tare memory,
individual identifiers (SQmin function, DKD measurement uncertainty)
Configuring a Task: Timer-controlled Functions

D
t Define which function should be timer-controlled.

*Acoustic signal (beep tone): The balance makes a beeping sound.
Lock in readout (hold display): The measured weight value remains
on the display for the defined time period.
Automatic printout of values: The displayed value is printed
at the defined time.
t Select the mode.

*Timer set to intervals: The function is triggered at regular intervals
(e.g., every 30 sec.)
Timer set to a specific time: The function is triggered at the fixed time
(after the start of the application) (e.g., at 08:00:00).
t Specify when the time and/or interval should be entered.

Enter fixed time: You must enter this time and/or interval now.
*Time setting can be changed during process: The time and/or interval
is only entered when the task is carried out.

t Specify whether or not there should be an automatic restart after

the timer-controlled function has been triggered.
*Off , no restart
On (restart automatically): The timer is restarted as soon as the
timer-controlled function has been carried out.


Executing a Task: Timer-controlled Functions

or
t If required, enter the time or interval

(hh:mm:ss, e. g., 00:00:30 for an interval of 30 seconds).

Totalizing
Totalizing
Purpose: Adding up weight values and calculating values. The weight values of all individual
components are recorded and can be logged.
Options: You can save a maximum of 65,535 components.
User rights: All settings for the “Totalizing” application are saved under the active user profile.
Each user can make their own settings for this application. For this reason, make
sure that the desired user profile is selected before you start.
Results: When a user creates a local totalizing task, the results are only saved locally for that
user. The results of global tasks, however, are available to all users and
the administrator.
Combination options: Calculation, averaging, weighing in percent, parts counting, checkweighing, mass
unit conversion, second tare memory, individual identifiers (SQmin function, DKD
measurement uncertainty)
Configuring a Task: Totalizing

D
(* = factory setting)
t Define how the weight value will be stored.
*Manually: The weight value is stored as soon as the corresponding cursor softkey
is pressed.
matically as soon as the balance has stabilized after filling and the value exceeds
the minimum load.
Automatically: last value at stability: The last weight value with stabil-
ity is applied automatically, as soon as the balance is unloaded and the value falls
short of the minimum load. If stability was reached repeatedly between measure-
ments, the last stable weight value will be stored.
You must now select the minimum load to be applied:
(none, 10, 20, ...*100 .. 1000 digits).
Weighing Mode with Automatic Storage:

t Select the weighing mode to be used for the weight values.
Weighing in: Initial weighing of samples in a container.
Final readout: Final weighing of samples in a container.

Totalizing
t Define when the number of measurements (items) will be set.

Enter fixed quantity: The quantity of items is defined beforehand.
Quantity can be changed during the process:
Enter the quantity of items when you execute the task.
t Define whether or not automatic taring should take place after storing the
value.


Executing a Task: Totalizing

or
t If required, enter the number of items that you want to add up.
t Place the first sample on the weighing pan.
t To start totalizing, select Start.
t During the task, you can view the results of previous measurements at any time
by selecting Calc.


Purpose: This application is used to ensure that the measurement uncertainty is displayed
dynamically so that it conforms to the data documented on the DKD calibration
certificate.
Requirements: The function can only be used when the balance has been prepared for this before-
hand by a service technician. The service technician determines the measurement
uncertainty of the balance via an onsite DKD calibration. The technician records
the measurements and the measurement uncertainty for weighing in the DKD cali-
bration certificate. He also saves the calculated data in the balance.
Options: The measurement uncertainty can be displayed as an absolute value (U), a relative
value (U*), or as process accuracy (PA).
Combination options: Mass unit conversion, second tare memory, individual identifiers (SQmin function)
Configuring a Task: DKD Measurement Uncertainty

D
t Select the measurement uncertainty display mode in terms of the maximum

capacity.
Display absolute uncertainty: Absolute value (e. g., 12.00 g)
Display relative uncertainty: Relative value (e. g., 0.000045%)
Display process accuracy: e.g., 0.00013%
t If you have selected process accuracy, enter the process accuracy factor now.



Executing a Task: DKD Measurement Uncertainty

or
y If you have selected absolute uncertainty, the uncertainty of the weight

value is displayed in a tab (e. g., U 12.01 g). This value is based on the DKD
value set by a service technician.
y If you have selected relative uncertainty, the relative uncertainty

of the measurement is displayed in a tab as a percentage of the weight value.
y If you have selected process accuracy, the process accuracy is displayed

in a tab in percent.

Second Tare Memory (Preset Tare)

Purpose: This application is used to define the second tare value. As soon as a second tare
value is used, Net1 appears on the display for the respective net value.
Options: You can either use a weight value or enter a numerical value as a second tare value.
Combination options: Mass unit conversion, individual identifiers (SQmin function, DKD measurement
uncertainty)
Configuring a Task: Second Tare Memory

D
y No pre-settings are required for this application.

Executing a Task: Second Tare Memory (Preset Tare)

or
t You have two options for defining the second tare.
Using a Weight Value as a Second Tare
t Place the object (container) on the balance whose weight value you want to
use as the second tare.
t To set the weight value as a second tare, select T1.

y The stored weight value is displayed as the second tare value. Net 1 is also
displayed next to the current weight value.
t To delete the tare memory, select Clr T1.
Entering a Numerical Value as a Second Tare

t Enter the tare value for T1 (e.g., 20).
t To set this value as a second tare, select T1.
y The tare value is displayed.
t To delete the tare memory, select Clr T1.

Parts Counting
Parts Counting
Purpose: This application is used to determine the number of objects which each have
approximately equal weight. This saves you from having to count individual parts.
Options: You can calculate or enter the piece weight of individual objects.
mass unit conversion, second tare memory, individual identifiers (SQmin function,
DKD measurement uncertainty)
Configuring a Task: Parts Counting
t Select the method that you want to use.

*With calculation of reference piece weight: The piece weight is deter-
mined by weighing a known reference piece quantity.
With input of reference piece weight: The piece weight is entered as a
numerical value.
With calculation of the reference piece weight:
t Define how the reference piece count should be entered.

Enter fixed reference quantity: You must enter this reference piece count
nRef now.
*Reference quantity can be changed during process: The reference
piece count is entered when the task is executed.
When entering the piece count:
t Define how the piece weight should be entered.

Enter fixed piece weight: You must enter this piece weight wRef now.
*Piece weight can be changed during process: The piece weight is entered
when the task is carried out.

Parts Counting
t Define the accuracy to be used for the weight value.

*Normal resolution: As displayed
10-fold (+ 1 dec. place): With one decimal place more than on the display
100-fold (+2 dec. places): With two decimal places more than on the display
Only with calculation of reference piece weight:
t Define whether or not the piece weight should be updated when counting.
Optimization off
*By pressing key, after prompt
Automatic updating


Executing a Task:
Parts Counting with Reference Piece Weight Calculation
or
y The last used reference piece quantity nRef is displayed.

t If you are working with a variable reference piece quantity, you must enter
or change this now.
t Place this exact amount (nRef) of the objects to be counted on the
weighing pan.

Parts Counting
y The weight value for the reference objects is displayed.

t To determine the average piece weight, select Start.
y The reference piece count and the average piece weight are displayed.
You can now begin with the parts counting of unknown amounts.
t Place any amount of the objects on the weighing pan.

y The determined piece count is displayed.
t To display the weight value of this amount, select Weigh.
y The weighing results and all parameters are displayed.
t To count the next unknown amount, empty the weighing pan and place
the next amount of objects onto it.
y The calculated piece count and the weighing results are immediately updated.

Parts Counting
Executing a Task: Parts Counting by Entering the Piece Weight

or
y The last used piece weight wRef is displayed.
t Use the cursor softkeys to select the input field for the piece weight.
t Enter the piece weight of the reference object (e. g., 50 g).
y The reference piece quantity and the entered piece weight are displayed.
t Place the sample with the objects to be counted on the weighing pan.
y The calculated piece count is displayed.
t To display the weight of this sample, select Weigh.
y The weight of the sample is displayed.

t To toggle between the display of weight value and piece count, select Count
or Weigh.
t To count the next quantity of objects, empty the weighing pan and place
the next sample onto it.
y The weighing result is updated immediately.
t To display the piece count of this sample, select Count.

Checkweighing
Checkweighing
Purpose: This application is used to check a weight value using preset control values.
Options: Control values can be exact target values or tolerance range limit values within
which the check value must lie.
The check results are shown on the display. They can also be used for further
electronic editing by activating the control ports at the data output.
Combination options: Totalizing, statistics, formulation, mass unit conversion, second tare memory,
individual identifiers (SQmin function, DKD measurement uncertainty)
Configuring a Task: Checkweighing

D
t Define which values are to be used for checkweighing.

*Target, min., max. weight: The target value and a tolerance range in absolute
values
Minimum and maximum weights: Only a tolerance range in absolute values
Target; minimum and maximum in %: The target value and a tolerance range
as a percentage
t Define how the control values will be entered.

Enter fixed limits: You must enter these values now.
*Variable values (input): The check values can be entered now, but can still be
changed later when the task is carried out.
t Select the display mode for the results.

*Absolute value: Displays the absolute value.
Difference betw. target and actual: The deviation from the target value is
then displayed.

Checkweighing
t Define how the ports should be activated depending on the check results
*Ports not active
Within checkweighing range: Ports are only activated when the results
are within the checkweighing range.
Ports always activated: The ports are always activated with each weight value.
When stable and in checkweighing range: The ports are only activated
as soon as the balance becomes stable and the results are in the checkweighing
range.
At stability: The ports are always activated as soon as the balance has stabilized.
Once at stability and in the checkweighing range: The ports are acti-
vated on a one-time basis (not dynamically) as soon as the balance has stabilized
and the results are in the checkweighing range; effective until the balance has been
unloaded.
t Define whether or not the automatic counter for positive results should
be activated.
*No automatic counter
Counter for OK values: All positive checked results are counted.



Checkweighing
Executing a Task: Checkweighing

or
Define check values by entry:

t Select the input field Setp and enter the target.
t Select the input field Min or Max and enter the minimum or maximum check
values.
or
Define check values with current load:

t Place the weight on the weighing pan.
t Select More.
t Select the field of the check value with the current weight value you want
to use.
t If required, repeat the process with additional weights for the other check
values.
t To exit the input mode without saving the value, select Back.
t To start checkweighing, select Start.
y The entered check values are displayed graphically.
t Place the object to be checked on the weighing pan.

Checkweighing
y The weighing result is displayed.

y It is also possible to see the weighing result on a graphic scale for a set target
range.
It can be seen immediately on the graphic scale if the result is outside

of the tolerance.
t To switch the display to check mode, select Check.
y The display will now show whether the weighing result has gone over upper
limit (HH) or under the lower limit (LL).
t To check additional objects, empty the weighing pan and place the next object
on it.
y The display is updated dynamically.
t You can toggle between weighing and checkweighing at any time by selecting
Weigh or Check.

Importing/Exporting Data
You can use an SD memory card to move and exchange data (import/export).
This card is required when you want to save data externally or when you want
to exchange data with other balances. For example, you can easily copy user
profiles to several balances.
Inserting Memory Cards into the Display and Control Unit

The slot for the SD card is located at the back of the display and control unit.
1. Tilt the control unit until is it nearly vertical.

2. Swivel the cover of the card slot to the front. Align the SD card so that the con-
tacts are facing down.
3. Insert the card into the slot as far as it will go.
t To remove the card, press it against the resistance in the direction of the slot
so that the card springs out.
4. Press the position retainer and swivel the display and operating unit back into
the desired position.
The following data can be imported or exported via the SD card:
– Global tasks and separate tasks
– User profiles with their separate tasks
– Menu parameters
– Alibi memory
– Audit trail
– Calibration and adjustment data
– Individual, customer-specific applications “Q-Apps”
h You can view the data from the alibi memory (xml files) with any web browser
and import them to Microsoft Excel as well.

t Select the Import/export data menu item.
t Insert the SD card into the slot as shown in the picture.
t Select whether you wish to export or import data.
Export
t Mark the data you wish to export and select Next.
t Edit the name of the export folder, if desired, and select Next.
y The data is copied to the SD card.
y An icon is shown on the display during the data transfer.

The device cannot be operated during this time.

Import
In order for the data to be detected by the balance when importing them, always
copy the entire subdirectory rather than individual files.
- data
- all
- EXPORT-dd-mm-yyyy
- task
- language
t Select the folder on the SD card from which you want to import
data.
t Mark the data you wish to import and select Next.

y The data will be imported from the SD card.
y An icon is shown on the display during the data transfer.

The device cannot be operated during this time.
If the following error message appears:

Wrong XML version. Please check the data.
t Select Next.
y All previous data will be saved in the new format.
t Check your settings after importing the data (Menu, TASK, and USER).
t If the XML files continue to cause problems, contact your local Sartorius Service
Center.

Calibration and Adjustment

Background During calibration, a calibration weight is used to determine how much the
displayed value deviates from the actual measurement value. This deviation is
compared with an entered target value and is then eliminated by a subsequent
adjustment of the balance. During the Linearization, the deviation of the values
from the ideal characteristic curve is cleared.
Not all functions/settings can be selected on balances used as legal measuring

instruments.
When and how often Calibration/adjustment should be carried out on a regular basis, e. g., daily after
the balance is turned on. In addition, it should be done after each leveling and
always when the ambient conditions have changed (temperature, humidity, or air
pressure), and when the balance has been set up in another location.
isoCal All Cubis® balances are equipped with the automatic calibration function isoCal
(time and temperature-controlled). You can adapt this function according to your
requirements. You can set up a memory function that triggers a prompt for
calibration/adjustment at specified intervals.
h The process for the calibration/adjustment function may differ depending on the
preset configuration (see System Settings > Calibration/Adjustment Data).
The factory settings have not been changed for the procedure described here.
Calibration/Adjustment Using Internal

Calibration Weight
t If required, switch to operating mode.
J t Press TARE to tare the balance.
t Select Cal./Adj.
t Select Internal calibration/adjustment or, if this option is already

marked, select Start.

y The procedure will be executed.

t Wait until calibration/adjustment has been completed.
y The results are displayed after the procedure is completed.
t To return to operating mode, select Back.
Calibration/Adjustment Using External

Calibration Weight
h An external calibration weight is required for this function.
Please note the tolerance of the calibration weight being used.
t If required, switch to operating mode.

J t Press TARE to tare the balance.
t Select Cal./Adj.
t Place the calibration weight on the balance.

t Select External cal./adj. with factory-defined weight or, if this
option is already marked, select Start.
y Calibration is carried out (approx. 15 to 20 sec.)

y After calibration, the determined deviation is displayed.
t To adjust the balance, select Adjust.

t To complete calibration without adjustment, select Exit.

y Lastly, the results are shown on the display.
t To return to operating mode, select Back.

User Management
User Management
You can configure the following settings in this menu:
– Creating new user profiles (only possible as administrator)
– Editing user profiles (modify, copy, delete, change and delete passwords,
depending on user rights)
– Activating users
User Management
The user administration allows for defining of users with distinct sets of rights:
the administrator and multiple users.
The administrator can use all functions (except those in service) and he/she has all
user rights. Only he/she can create new user profiles and assign individual rights.
There is only one administrator.
A user, on the other hand, cannot use all functions. He/she has limited rights,
which are defined in the user profile. A max. of 15 user profiles can be created.
When the balance is first delivered, there are no user profiles, all settings can
be carried out. The first user profile that is created is automatically an administra-
tor. This person can then create additional user profiles.
H t To open the User Management menu, select the USER H key.
y The menu opens and the selection of user profiles is displayed.
Creating User Profiles

h This function is only available to an administrator.
The following settings can be made in the user profile and are only valid for that
user:
– Language
– Display settings (color, brightness)
– Volume and acoustic signal on/off
– User rights
– Password protection
– User name and description.

User Management
H t To create a new user profile, select Edit.

USER H
t Select Create.
The program now automatically guides you through the menu. Make your selec-
tions by selecting the desired option with the cursor softkeys. The program then
takes you to the next prompt.
or
If the desired option is already selected (highlighted), select Next to reach the next
prompt.
If more than one option can be selected for a single setting, press Next after
making your selection(s) to proceed to the next prompt.
Step 1: Select Language

t Select the desired language.
Steps 2 to 4: Set Background, Brightness, and Acoustic Signal

As a default the background is black with white text. The inverse setting is exactly
the opposite, i.e. a white background with black text.
t Select the desired setting.
y The display changes to the brightness setting.

t Select the desired brightness for the display.
y The display changes to the acoustic signal setting.

t Select the desired volume or switch off the signal.
Step 5: Assign User Rights

t Select the corresponding options to define which functions the user can access.
The following rights can be assigned individually:
– Creating, copying, modifying, and deleting tasks
– Importing data
– Modifying the calibration and adjustment settings
– Modifying the balance settings
– Creating, modifying, and deleting timer-controlled actions
Administrators can access all functions.
t To move to the next menu item, select Next.

User Management
Step 6: Configure Password Protection

If you assign a password, this profile cannot be used until the password has been
entered.
t Select the corresponding option to define whether the user profile is password-
protected or not.
The password will be defined in the step after next.
Only the administrator can open the user profile without the password (for example,
if the user forgets the password) and assign a different password. The administrator
can remove the password protection so that a new password can be set, if desired.
If the administrator forgets the password, please contact your Sartorius Service
Center.
Step 7: Check All Settings

t To see all settings, page down with the cursor softkeys.
t To modify a setting, press the corresponding button. This opens a screen
showing the options for that setting.
t If the settings are correct, select Next.
Step 8: Define the Password (if Password Protection Enabled)

y If you selected the option for password protection, you are now prompted to
enter the desired password twice.
t Select the upper button.
t Enter the desired password (minimum 4 characters, maximum 8;
only numbers and uppercase letters are permitted).
t Press the lower button, and enter the password again.
t Select Next.
Step 9: Enter User Names and Descriptions

t To enter a name for the user profile, select the User Profile Name button.
The user name is shown on the top right of the display during operation
as long as the respective user profile is active.
t Enter the name (max. 40 characters) and select OK.
t To enter a description for the user profile, select the User Description
button.
The user description can be viewed at any time during operation of the balance
by pressing the user info area on the display (see “Display”).
t Enter the description and select OK.
t To complete the process, select Save.

User Management
y The program switches to user selection. The newly created user profile is placed
at the end of the list.
t If you would like to activate the new user profile, select it here.
y The program switches to the operating mode and the selected user is activated.
or
t To create additional user profiles, select Edit and repeat the procedure
as described above.
or
t If you want to switch to operating mode without switching the user,
select Start.
Activating Users
When the balance is in operating mode, the active user profile is displayed
in the user field at the top right of the screen. To activate another user, you must
switch to the User Management menu.
H t Press the USER key H.
y The user list is displayed. The current, active user can be recognized
by the small arrow and the dark background.
t Select the user profile you would like to activate.
t If the user is password-protected, enter the password and confirm the entry.
y The program switches back to operating mode with the selected user activated
and displayed at the top right of the user field.

User Management
Editing User Profiles

H t If you have not already done so, open the User Management menu by
touching the USER H key.
t To open the menu for editing profiles, select Edit from the user selection
screen.
y The selection of edit functions is displayed.
h Which options for editing user profiles are available depends on whether or not
you have administrator rights. The following table shows who can carry out
which changes to user profiles.
Accordingly, the displays shown in this section may differ from your screen
because the administrator view is always shown here.
Option Administrator User

Change own profile i i
Change other profile i
Copy profile i
Delete profile i
Change or delete own password i i
Change or delete other user passwords i
Changing User Profiles

t Select Modify.
t If you are logged in as an administrator, you must select the profile you would
like to change and then select Next.
y The overview of all settings for this profile is displayed. You can now select
and change the parameters one by one.
or
t To have the program guide you through all settings step by step, select
Wizard. Now all setting options will be displayed one by one to be changed.
t Select Next.
t If required, change the user name and description.
t Select Save.
y The user profile has been changed. The display changes to the user selection.
Copying User Profiles

h This function can only be carried out by an administrator.
h When you copy a user profile with password protection, the password
is not transferred to the copy, but is deleted instead.
t Select Copy.
y All available user profiles are displayed.
t Select the profile that you want to copy.
t Select Next.
t Enter a new name and description for the copied user profile.
t Select Save.
y The display switches to the user selection in which the new profile is displayed.

User Management
Deleting User Profiles

h This function can only be carried out by an administrator.
t Select Delete.
y All available user profiles are displayed.
t Mark each profile that you wish to delete and select Next.
or
t To delete all profiles, select All.
y All profiles selected for deletion are displayed in a security prompt.
t If you wish to modify the selection, select No.
or
t Confirm the deletion with Yes.
Changing or Deleting Own Password

t If you haven’t already done so, activate your own user profile.
t Select Edit in the user selection.
t Select Change or delete own password.
t To change the password, select Yes.
t Touch both buttons one after the other and enter the new password twice.
or
t To delete the password, select No.
t Select Next.
y The display switches to the selection of change functions.
Deleting Other User Passwords

h This function is only available to an administrator.
t Activate your own profile.

t Select Edit in the user selection.
t Select Delete other passwords.
y An overview of all users with passwords is displayed.
t Mark each user whose password you wish to delete and select Next.
or
t To delete all passwords, select All.
y All users whose passwords you selected are displayed in a security prompt.
t If you wish to modify the selection, select No.
or
t Confirm the deletion with Yes.
y The display switches to the overview of user settings.

Interfaces
Interfaces
Purpose Interfaces are used to exchange data with ported peripheral devices: Measured
values and calculated values can be output to a printer, PC, or control display;
conversely, control commands and data inputs can be sent to ported devices
(PC, keyboard, foot switch, barcode scanner).
Except for PS2, each interface has to be configured according to the peripheral
device and desired function. No error messages are generated when no devices
are connected to an interface port (open data port).
Features Cubis® series balances have at least three interfaces:

1 Peripheral port (25-pin interface), Com A
1
2 USB interface for a PC connection, Com B
2 3 The slot may contain other ports (Com C):
– 25-pin interface (YDO01MS-R)
– 9-pin interface with PS2 port (YDO01MS-P)
– Bluetooth® Module (YDO01MS-B)
4 Ethernet interface (on the bottom of the display unit), Com D
3
4
Data exchange protocols For data exchange, the interfaces are configured with the following protocols:
– Printer output
– SBI (Sartorius Balance Interface): Sartorius standard protocol for output to a
PC or control unit. This simple ASCII-based protocol allows you to use ESC
commands from your PC to control the basic weighing functions.
– xBPI (eXtended Balance Processor Interface, also called X-Bus): binary protocol
with extended command volume. This protocol lets you control numerous
weighing functions. For further information on this, please contact Sartorius.
– SICS (Standard Interface Common Set): This interface protocol enables opera-
tion and control of the balance via a connected PC. You can read out measure-
ment data, enter weighing commands, and activate all operating functions.
To use the protocols, application software must be installed on the PC,
e. g., SartoTerminal.
Synchronization During data communication between balance and PC, messages consisting of ASCII
or binary characters are transmitted via the interface. For error-free data exchange,
parameters for baud rate, parity, handshake mode, and character format must
be identical for both units.
You can configure the respective settings in System Settings (menu). In addition
to these settings, data output for the balance can also be made dependent
on several conditions that are defined in the individual tasks. These conditions
are described under each of the tasks.

Interfaces
USB Port (PC)

Purpose Any Cubis® balance can be connected to a PC equipped with a USB port. A vir-
tual serial interface (virtual COM port) is set up as a device type at the USB port.
This virtual serial interface is identified und operated by the application program.
The protocols xBPI, SBI, and SICS can be transmitted via the USB port.
3
The USB port is designed for the laboratory environment and is not suitable for
use in purely industrial environments. Full IP protection is only guaranteed when
the USB cover is closed.
System Requirements – Computer (PC) with Windows 98SE®, Windows ME®, Windows 2000®,
Windows XP®, Windows Vista®, or Windows 7®
– Available USB port on the PC
– USB cable
Software Driver and Installation Guides Models MSU116P, MSU66S, MSU66P, MSU36S, MSU36P:
The USB driver for the virtual, serial interface is Microsoft-listed and available
online via the Microsoft Update Service: USB CDC serial port emulation
All remaining models:
The VCP driver, used to set up the virtual interface on the computer, can be down-
loaded from the internet:
http://www.ftdichip.com/FTDrivers.htm
The installation guides for the drivers can be found at
http://www.ftdichip.com/Documents/InstallGuides.htm
Connecting the Balance via USB
h The current USB port for the computer is established when the software driver
is being installed. The driver must be re-installed every time you wish to change
the port.
Therefore, choose one USB port that can permanently or regularly be used
to connect the balance.
t Switch off the balance.

t Unplug the balance from the mains.
t Connect the USB cable to the balance and to the USB port on the computer.
t Plug the balance into the mains again and switch it on.
y Windows detects the device connected to the USB port. If the device is being
connected for the first time, the Windows Installation Wizard will run.
Installing Software Drivers

t Run the Installation Wizard for the driver.
t Follow the instructions that appear.
t To complete the installation, click on Finish.
y The virtual interface is now ready for operation.
Windows® usually adds the virtual port in the position following your
highest-numbered COM port.
Example: For a PC with up to 4 COM ports, the new virtual port would then be COM5 (see
Device Manager).
Installation Guides for Windows XP®, Windows Vista®, and Windows 7®

Changing the Port Number If you use the USB interface with a program that limits the number of COM port
designations (e. g., COM1, 2, 3, 4 only), you may have to assign one of these port
numbers to the new virtual port.

Interfaces
t Open the setting for the USB serial port in the Windows® Control Panel:
– START > My Computer > Control Panel
– System > Hardware > Device Manager
t Open the Connections submenu.
t Double-click on USB Serial Port.
t Select Port Settings > Advanced.
Changing Latency Time t Open the settings for the USB serial port, following the above instructions.
t For a faster rate of communication, change the setting for the latency timer
to 1 msec.
Plug & Play Mode in Autoprint (SBI) t Open the settings for the USB serial port, following the above instructions.
t Stop the Plug & Play mode from running.
Uninstalling the Driver

The software driver for the USB connection can be uninstalled with the Windows®
Uninstaller.
PS2 Interfaces for Barcode Scanner or Keyboard

Via the PS2 port you can connect a barcode scanner or a PC keyboard to enter data
and operate the balance.
Installation The interface installation is described in the installation instructions supplied.
Connecting the Device t Plug the connector plug into the PS2 port on the balance.
y The input device is operational; no further settings are required.
Using the Input Device You can input entries directly via the keyboard or barcode scanner whenever
an input field is open on the display of the balance.
Key Assignment for the PC Keyboard

The five context-dependent buttons located at the bottom edge of the display are
operated via the Function keys F1 to F5 on the PC keyboard.
F1 F2 F3 F4 F5
If the last button on the right is assigned with the function Back, this function can
also be activated using the Esckey on the keyboard.
Esc
D F9 The TASK key is operated via F9 (Open Task menu).
H F10 The USER key is operated via F10 (Open User menu).
p Print The PRINT key is operated via the print key on the keyboard.
Shift F1 Use Shift F1 to select the first entry in a menu.
Shift F2 Use Shift F2 to select the second entry in a menu.
etc.
Pin Assignment PS2

Pin 1: Keyboard_DATA (universal)
6 5 Pin 2: Not assigned (larger)
4 3 Pin 3: Internal ground (GND)
2 1 Pin 4: +5 V
Pin 5: Keyboard_CLK (Set)
Pin 6: Not assigned (smaller)

Interfaces
Interfaces (RS-232) 25-pin and 9-pin

The balance is standard-equipped with a 25-pin interface(peripheral port) where
1 13
14 25
different Sartorius peripheral devices can be connected, e. g., hand or foot switch.
This interface is also used for the control lines for the Checkweighing application.
A 9-pin interface can be optionally installed. This port is intended for

1 5 connecting a PC.
6 9
3
When Using Pre-wired RS-232 Connecting Cables for the 25-pin
Interface:
RS-232 cables purchased from other manufacturers often have incorrect pin
assignments for use with Sartorius devices. Failure to do so may damage or destroy
your weighing system and/or peripheral devices!
t Be sure to check the pin assignments before you connect cables purchased
from other manufacturers.
t Disconnect any lines assigned differently (e. g., Pin 6).
Features (* = factory settings)

Type of interface: Serial port
Interface operating mode: Full duplex
Level: RS-232
Interface connector: D-SUB connector, 25-pin or 9-pin
Transmission rate: 600, 1200, 2400, 4800, *9600, and
19200 baud (selectable)
Parity: *Even, odd , none; blank spaces (selectable)
Character transmission: Start bit, 7/8* bit ASCII, parity, *1 or 2 stop bits
(selectable)
Handshake (selectable): 25-pin For 2-wire interface: Software (XON/XOFF)
For 4-wire interface: *Hardware (CTS/DTR)
9-pin Hardware (CTS/RTS)
Operating mode: *SBI, xBPI, printer, SICS, 2nd display
Manual print mode: Without stability, *after stability
Auto print mode: *Without stability, at stability, after load change
Cancel automatic printing: Not possible
Time-dependent automatic printout: After 1 display update
Data output of balance: 16 or *22 characters
Tare after individual printout: Off
Basic values, application: Off
Connectable Peripherals The following devices can be ported to the interface:

– Verifiable data printer YDP03-0CE, YDP10-0CE, YDP20-0CE
– Verifiable data printer with Bluetooth data transmission YDP10BT-0CE
(module required)
– Universal (serial printer)
– Strip/label printer YDP04IS-OCEUV
– Hand switch YHS01
– Foot switch YFS01, YPE01RC
– External control display YRD11Z
– Second display YRD03Z

Interfaces
Pin Assignment Chart for Connecting Peripherals

Purpose: For Sartorius peripheral devices
Female Interface Connector: 25-pin D-Sub (DB25S) with screw connection
Required Male Connector (Recommended): 25-pin D-Sub, DB25S, with integrated shielded cable clamp and
shield plate assembly (Amp type 826 985-1C) and fastening screws
(Amp type 164 868-1)
Pin assignment 25-pin socket, RS-232:

1 13 Pin 1: Signal ground Pin 14: Internal ground (GND)
14 25
Pin 2: Data output (TxD) Pin 15: Control input/output 12)
Pin 3: Data input (RxD) Pin 16: Control input/output 22)
Pin 4: Signal GND Pin 17: Control input/output 32)
Pin 5: Clear to send (CTS) Pin 18: Control input/output 42)
Pin 6: Not used Pin 19: Control input/output 52)
Pin 7: Internal ground (GND) Pin 20: Data terminal ready (DTR)
Pin 8: Internal ground (GND) Pin 21: Not used
Pin 9: Not used Pin 22: Not used
Pin 10: Not used Pin 23: Not used
Pin 11: + 12 V output Pin 24: Not used
Pin 12: Reset _ Out1) Pin 25: +5 V output
Pin 13: + 5 V output
1) = Peripherals restart
2) = Assignment of control inputs/outputs can be configured in each menu
(see below)
Control Inputs/Outputs
Data Output /
Setting Pin 15 Pin 16 Pin 17 Pin 18 Pin 19
Infrared sensor Input 1: Output 2: Output 3: Output 4: Output 5:

YHS01MS *“PRINT” key **“Smaller” **“Equal” **“Larger” **“Setp”
Hand switch Input 1: Output 2: Output 3: Output 4: Output 5:
YHS02 *“PRINT” key **“Smaller” **“Equal” **“Larger” **“Setp”
Foot switch Input 1: Output 2: Output 3: Output 4: Output 5:

YFS01 *“PRINT” key **“Smaller” **“Equal” **“Larger” **“Setp”
Triple foot switch Input 1: Input 2: No function No function Input 5:

YPE01RC Left Right (disabled) (disabled) Center
*“PRINT” key *Left Shieldpl.key *“TARE” key
Control display Output 1: Output 2: Output 3: Output 4: Output 5:

YRD11Z Currently **“Smaller” **“Equal” **“Larger” **“Setp”
no function
Control inputs Input 1: Input 2: Input 3: Input 4: Input 5:

*“PRINT” key *Left Shieldpl.key *no function *no function *“TARE” key
Control outputs Output 1: Output 2: Output 3: Output 4: Output 5:

Currently **“Smaller” **“Equal” **“Larger” **“Setp”
no function
* Default assignment of input, otherwise configurable

** Assignment of output for checkweigher
Interfaces
Wiring Diagram for 25-pin Interface

Diagram for connecting a computer or other peripheral device to the balance using
the RS-232/V24 standard and cables up to 15 m (50 ft.) long
3 Do not connect any other pins to the cable connector of the balance!
Balance/scale Computer,
25-pin 9-contact
male connector female connector
TxD 2 2
RxD 3 3
CTS 5 4
DTR 20 8
GND 4/7 6
GND 14 5
Cable type: AWG 2 specification
Pin assignment 9-pin socket, RS-232:

1 5
Pin 1: Not used
6 9 Pin 2: Data output (TxD)
Pin 3: Data input (RxD)
Pin 4: Not used
Pin 5: Internal ground (GND)
Pin 6: Not used
Pin 7: Clear to send (CTS)
Pin 8: Request to Send (RTS)
Pin 9: Not used
Establish a connection via a conventional RS-232 cable.

Interfaces
Configuring Serial Ports
y The available ports are displayed.

t Select the port you want to configure.
t Configure all settings for this port.
Configuration Options for the Serial Ports

The following operating modes are available for this port:
– No function; the interface is blocked
– xBPI
– SBI
– Second display (SBI)
– Printer output
– SICS
Configuration Options for xBPI Operating Mode

For this operating mode, you can only configure baud rate and number of stop bits.
– Selected protocol: No protocol (fixed setting)

– Baud rate: *9600 to 115200 baud
– Data bits: 8 (fixed setting)
– Parity: Odd (fixed setting)
– Stop bits: *1 or 2 stop bits
Configuration Options for SBI Operating Mode and Second Display

You can change all settings for this operating mode.
– Selected protocol: No protocol / Software handshake XON; XOFF /

*Hardware handshake RTS; CTS
– Baud rate: 300 to 19200 baud (to 115200 baud for second display), *9600
– Data bits: 7 or *8
– Parity: None / *Odd / Even
– Log data: *Turn off / Turn on

Interfaces
Configuration Options for Printer Output Operating Mode

You can modify all settings for this operating mode depending on the configured
printer type.
– Printer type: YDP10-0CE/YDP20-0CE/YDP03-0CE/Universal/

YDP04IS-0CEUV
– Selected protocol: Hardware handshake
– Baud rate: 300 to 19200 baud (*9600)
– Log data: *Turn off / Turn on
The following setting options are available for the printer types:
– YDP10-0CE: No setting option; all parameters are permanently defined

– YDP20-0CE: All can be configured except stop bits
– YDP03-0CE: All can be configured except data bits and stop bits
– Universal: All can be configured
– YDP04IS-0CEUV: No setting option; all parameters are permanently defined
– YDP10BT-0CE (for optional Bluetooth module only, Com C): No setting

option; all parameters are permanently defined
Configuration Options for SICS Operating Mode

You can change all settings for this operating mode.
– Selected protocol: No protocol / Software handshake XON; XOFF /

*Hardware handshake RTS; CTS
– Baud rate: 300 to 115200 Baud, *9600
– Log data: *Turn off/Turn on

Interfaces
Explanations for the Setting Parameters

Selected Protocol/Handshake
The SBI (Sartorius Balance Interface) has transmit and receive buffers. Data trans-
mission can be operated with a hardware or software handshake.
Hardware Handshake (CTS/DTR): With a hardware handshake (4-wire interface) protocol, the handshake is controlled
via the CTS and DTR lines.
Software Handshake (XON, XOFF): The software handshake is controlled via the XON and XOFF control commands.
When the device is switched on, XON must be transmitted to enable any connected
device to communicate.
Data transmission:
Balance ––– byte –––> PC

(transmitting device) ––– byte –––> (receiving device)
––– byte –––>
––– byte –––>
<––XOFF –––
––– byte –––>
––– byte –––>
…
(Break)
…
<––XON –––
––– byte –––>
––– byte –––>
––– byte –––>
––– byte –––>
Transmitting Device: Once XOFF has been received, it prevents further transmission of characters.
Once XON has been received it re-enables the transmitting device to send data.
Receiving Device: To prevent too many control commands from being received at one time, XON is
not transmitted until the buffer is almost empty.

Interfaces
Bluetooth® Interface (COM C, Optional)

How to install the Bluetooth® module is described in the supplied installation
instructions.
In order to transmit data via the Bluetooth module, the interface must first
be configured.
Configuring the Bluetooth® Interface

t If appropriate, toggle to the System Settings menu.
t Select the Device parameters submenu.
t Select Configure ports.
t Open the Serial ports submenu.
t Select Available ports.
The following operating modes are available for this port:

– No function
– SBI (data exchange with PC or notebook)
– Printer output
– SICS protocol (data exchange with PC or notebook)
t Select the desired operating mode.
Bluetooth Printer Output Operating Mode

t If required, you can change the device name (only with Bluetooth modules
from Version 04-10-01).
t To connect a PC/notebook, select PC or other devices.

Interfaces
Establishing a Radio Connection with the Bluetooth Printer

t Make sure that the printer to which you wish to connect is ready to operate.
t Select the Sartorius BT printer as the device.
t To establish the connection, select Scan.
y The balance will now search for the Bluetooth device. This process may take
time. Wait for the next message to appear on the display.
y A message will appear to confirm whether the printer has been found.
y The connection will initially be terminated after saving.

The LED on the printer will continue to flash blue/red.
y As soon as the configuration menu is exited, the connection will
be re-established. The LED on the printer will then illuminate permanently
(blue).

Interfaces
Network Interface (Ethernet)

Purpose This interface lets you integrate your balance into a TCP/IP-based network.
System Requirements The person configuring the Ethernet interface should have basic knowledge of TCP/
IP-base networks and network technologies in general.
The Ethernet interface is connected to the local network via the RJ45 slot.
Features
Transfer rate: 10 Mbs/sec (10BASE-T, Ethernet) and 100 Mbs/sec
(100BASE-TX, Fast Ethernet), auto-recognition (10/100,
HalfDX/FullDX)
Connection type: Network protocol: TCP
Transport: TCP/IP or UDP /IP
HMS certificates: Compatible with the TCP standard, industry-compatible as
per CE, UL, cUL
Cable: Twisted pair, shielded, CAT-5 or higher, 1:1, UTP / STP,
male connector RJ45; e. g., patch cable CAT5 depending
on application (straight/crossover)
Cable impedance: 150 ohm
Cable length to HUB: Max. 30 m
Connecting Network Cables

The slot for the network port is located at the back of the control unit.
1
t Tilt the control unit (1) until it is nearly vertical.
On the bottom panel of the display unit:
t Turn the locking lever (2) 90°.

Interfaces
t Remove the cover plate (3).

3
t Insert the Ethernet cable plug (4) so that it clicks audibly into place.
t Reattach the cover plate (5).
t Turn the locking lever back to its locked position.
3 Exercise caution to avoid glass breakage for models with a draft shield.
t Lay the Ethernet cable (6) through the cable channel of the weighing module.

Interfaces
Configuring Network Operation (Ethernet)

Preparation: Before you can start with the configuration, you will require some information
about your network. Please contact your network administrator. The important
question is whether your network supports DHCP or not.
DHCP With DHCP, you can automatically link a (new) balance to an existing network
without having to configure it manually. Normally, the balance (client) only
requires the automatic acquisition setting for IP address (factory setting).
DHCP is supported In this case, no additional information is required.
DHCP is not supported In this case, you need the following information from the network administrator:
– IP address
– Subnet mask
– Default gateway address
Device name (host name): This name can be changed if required.
This name is used to select the balance in the network.
Selecting Network Setting (Fixed Setting)

t Select the Device parameters submenu and slide the
right scroll bar down.
t Open the Network settings (Ethernet) submenu.
t To change the IP settings, select the input field behind

Network configuration.
t Select Use fixed IP address and confirm with OK.
t In the overview, check all settings and change as required.
Device name (host name): You can select this name freely.
This name is used to select the balance in the network.
t If you then want to establish an Ethernet connection, write down the IP

address now.
t To save the network settings, select Save.

y The “Configure ports” submenu is displayed.

Interfaces
Configuring Network Interface (Com D)

t Select the Device parameters submenu and slide the right scroll bar down.
t Open the Network ports setup. submenu.
t Define the operating mode and, depending on the connection type, either
server port and address or the local TCP port.
Operating mode: No function assigned / XBPI / SBI / Printer output /
SICS protocol
Connection type (of the balance): Server / Client
Examples:
For the connection type Balance = Server you only need to enter the local TCP port
(e. g., for working with the Sartorius SartoCollect software for data communication).
For the connection type Balance = Client, you have to enter the server TCP port
and the server IP address (e. g., for working with “Virtual serial port emulator”
as the server for all previous serial PC applications with the balance or for printing
on a network printer server).
Remote Control of the Balance from a PC via Ethernet

System Requirements
– PC with Internet browser
– Operating systems Windows, Mac OS, Linux, Unix, and Solaris.
Installation
t Connect the balance to your network via the Ethernet interface.
t Enter the IP address of the balance in the address field of your Windows
browser.
The IP address of your balance is listed under Menu > Device Information > Display
device information.
Port Release
– If you are having problems with the connection, you must configure your
firewall to release the right TCP/IP UDP port.
– If you are using a router and want to access your computer via the Internet using
your IP address, the port must also be set in the router’s virtual server settings.
This means that you must forward the port to the IP address of the server.
– If you still have problems, you may have to deactivate your firewall temporarily
while using a browser connection.

Interfaces
Selecting Functions
t Click on the desired function in the browser.
t To exit a function, click on >>Back or on the Go back key of your browser.
Remote configuration (VNC): Use this function for remote control of the
balance. The display screen on the balance is reproduced in the browser, you can
operate the balance now by using the mouse and keyboard of your PC
Software version: You can view the version of the balance, control unit and
application software.
Screenshot: You can print the current screen or save it as a GIF file.
Browse alibi memory: View the Alibi memory. This function can also be deactivated
by Sartorius Service.
Show settings: You can view the following settings:
– Task profiles
– User profiles
– System settings (menu)
– Service information (service)
– Interface information (ports)
– Timer controlled actions
Show log files: You can view the respective log files.
Web Services: The balance has a “Web Services” communication function. This
standardized communications technology allows external software systems like
LIMS, ELN, etc., to display and use information, entry fields, menus or complex
operations on the touch screen of the balance. Bidirectional data transfer is enabled
without complicated driver software. This eliminates the need to install PCs, laptops
or terminals in the area directly around the balance.
QWeb “Cubis ® individual”: Download Q-Apps to your Cubis® laboratory balance
and test them free for 30 days.
Viewing a Print File Directly in an Internet Browser
Requirements:
Preferences can be found in the Chapter “System Settings (Menu)”: Configuring
“Print to file” Select the following file format for viewing directly in an Internet
browser: Print to TXT file.
t In the browser, click on “Show Log Files” and then “Print to File.”
t To view the printout directly in the Internet browser, click on “print.txt.”
y The printout is displayed in the Internet browser.

Interfaces
Data Output
You can define the data output parameter so that output is activated either when
a print command is received or automatically synchronized with the display
or at defined intervals (see application programs and autoprint settings).
Data Output by Print Command The print command can be transmitted by pressing P or by a software com-
mand (Esc P).
Automatic Data Output In autoprint mode, data is output to the data interface port without an extra print
command. You can have synchronized data output automatically at defined display
update intervals, with or without the stability parameter. The interval time depends
on the balance operating status and balance type. For Autoprint for the fasted
display result, set additional software handshake or no handshake.
If the automatic data output is activated in the Device Configuration, it starts
immediately after the balance is turned on. You can also configure whether
the automatic data output can be stopped and started by pressing the P key.
Output rate The max. output rate of the data interfaces depends on the selected menu settings.
Data Output Formats

You can output the value displayed in the measured value line and the weight unit,
with or without a data ID code. Configure this output parameter in the Device
Parameters menu (Menu > Device parameters > Configure data output > Line
format).
Example: Output Without an ID Code + 253 pcs 16 characters are printed
Example: Output Without an ID Code Qnt + 253 pcs 22 characters are printed
Data Output Format with 16 Characters

Display segments that are not activated are printed as spaces.
Display values without a decimal point are printed without a decimal point.
The type of character that can be printed depends on the character’s position.
Normal Operation
Position 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
8 characters + A A A A A A A A A * E E E CR LF
9 characters + A A A A A A A A A A E E E CR LF
or – . . . . . . . . . . * * *
or * * * * * * * * * *
*: Spaces CR: Carriage return

A: Displayed characters LF: Line feed
E: Symbol for the unit, or “!”
as a warning symbol for
calculated values

Interfaces
Special Outputs
Position 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
* * * * * * – – * * * * * * CR LF
or* * * * * * A * * * * * * * CR LF
or* * * * * * A B * * * * * * CR LF
and only upon request with ESC w0 (no print command):
* * * * * W * X X X Y Y Y CR LF
or* * * * * * I * X X X * * * CR LF
*: Space A = C: Calibration/Adjustment
AB = – –: Final readout W: Draft shield status (optional):
A = H: Overload I: Ionizer (optional)
AB = H H: Overload in checkweighing Y,Y,Y = Draft shield doors
A = L: Underweight XXX = Decimal value calculated from
AB = L L: Underweight in checkweighing binary data
Decimal value Binary value Control information

Bit0 = 0: No error/ionizer off
1 Bit0 = 1: Draft shield error/ionizer on
Bit1 = 0: Draft shield motors off
2 Bit1 = 1: Draft shield in motion
Bit3 = 0: Learning function off
8 Bit3 = 1: Learning function on
Bit4 = 0: At least one draft shield door open
16 Bit4 = 1: All draft shield doors closed
Bit6 = 0: Motorized draft shield operation
64 Bit6 = 1: Manual draft shield operation
R,M,L = COO: Right door closed (Closed), Middle and Left doors open (Open)
R,M,L = OCC: Right door open (Open), Middle and Left doors closed (Closed)
Error Message
Position 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
* * * E r r * */# # # * * * * CR LF
*: Space # # #: Error code number
Example: Output of the weight value + 111.255 g

Position 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
8 characters * * * 1 1 1 . 2 5 5 * g * * CR LF
9 characters * 1 1 1 . 2 5 5 4 3 2 g * * CR LF
Position 1: Plus +, or minus – or space

Position 2: Space or weight value
Position 3 – 10: Weight value with decimal point; leading zeros are output
as spaces.
Position 11: Space
Position 12 – 14: Characters for unit of measure or space
Position 15: Carriage return
Position 16: Line feed

Interfaces
Data Output Format with 22 Characters
When data is output in this format, ID codes with 6 characters will precede data
with a 16-character format. These six characters identify the subsequent value.
Normal Operation
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
K K K K K K + A A A A A A A A A * E E E CR LF
* * * * * * – . . . . . . . . . * * * *
* * * * * * * * * *
K: ID code character1) E: Unit symbol character1)

*: Space See Section “Mass Unit Conversion”
A: Displayed characters CR: Carriage return
LF: Line feed
Special Outputs
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
S t a t * * * * * * * * – – * * * * * * CR LF
H H
L L
C
*: Space L: Underweight
– –: Final readout L L: Underweight in checkweighing
H: Overload C: Calibration/Adjustment
H H: Overload in checkweighing Draft shield and ionizer status
similar to data output format with
16 characters
Error Message
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
S t a t * * * * * E r r * # # # * * * * CR LF
*: Space # # #: Error code number
Print Format for Climate Data

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
A i r * t e m p e r a t u r e * C 1 * * * *
* * * * * * * * * * * * * * * 2 2 . 5 7 ’ C
*: Space

Interfaces
ID Code Character K Individual Identifiers

h The ID is based on model type, P-ID1 Print ID1
e. g., not all units and IDs are T-ID1 Task start ID1
available for balances used in
legal metrology. I-ID1 Initialization ID1
R-ID1 Result output ID1
C-ID1 Component ID1
Device Information, Basic Data E-ID1 Evaluation ID1
Manuf. Manufacturer X-ID1 Task end ID1
Model Model Density Determination
SerNo. Serial number ID-Dk Name of density
BAC: Balance version determination kit
APC: Display version n No. of wires
d Wire diameter
Print Function
D Vessel diameter
Name Name
Id-Liq Name of liquid
Task Profiles RefFl Density of liquid
Task Task name b Coefficient of expansion
TskDes Task description of the liquid
LA Correction for air density
User Profiles
Pl.vol Volume of glass plummet
User User name
Temp Temperature of liquid
UsrDes User description
RhoFl Density of liquid
Data Memory Corr Correction factor of the
MemNo. Memory number density determination kit
MemID Memory ID Wa Weight of sample in air
Wfl Weight of sample in liquid
Basic Weighing or weight of liquid
G# Gross weight 2 Wt Residual liquid
N Net weight Wr Sample plus weight of liquid
N1 Net weight (T10) Rho Density of sample
T Tare weight Vol Volume of sample
T1 Tare weight 1
Statistics
T2 Tare weight 2
nDef Default number of items
Calibration/Adjustment n Transaction counter
Set Target weight x Average value of the weight
Stat Status values
Dev Deviation weight s Standard deviation
s = Result ReproTEST of the weight values
sRel Variation coefficient
Leveling of the weight values
LevRes Leveling result Sum Total of all weight values
Max Highest weight value
SQmin Function
Min Lowest weight value
SQmin Minimum weight
Dif Difference between highest
and lowest weight value

Interfaces
ID Code Character K Totalizing

(Continued) nDef Default number of items
Calculation Comp Weight value start
Form Formula Comp Current weight value
Res Results using equations n Number of the item
X Variable X CompC Weight value start:
calculated components
Y Variable Y
CompC Current weight value:
a Variable a
calculated components
b Variable b
Sum Total of all weight values
Animal Weighing
mDef Target value
a1 Addend a1
Mul Calculation factor
b1 Factor b1
mAct Actual number
b1 e- Exponent b1
x-Net Results
a2 Addend a2
x-Res Calculated result
b2 Factor b2
Formulation b2 e- Exponent b2
IDCm1 Id Component 1 P fact Pa Factor
TCmp1 Reference weight Comp. 1 U Absolute process inaccuracy
PCmp1 Reference percentage weight U* Relative process inaccuracy
Comp. 1 PA Process inaccuracy
Comp1 Weight value Comp.1
WD1 Difference Weight 1 Parts Counting
wRef Reference piece weight
PD1 Difference Percent 1
nRef Reference sample quantity
WghMod Mode for inputting initial
weight Qnt Piece count
nDef Default number of
Checkweighing
components
Setp Target value
Total Total of weight values
Min Min. tolerance for checkw.
RSum Total reference
Max Upper tolerance for checkw.
n Transaction counter
Lim- Lower percentage
IniWgt Default total weight
Lim+ Upper percentage
Weighing in Percent Count Counter for correct values
pRef Percentage of reference CountLL Counter for too small
Wxx% Reference percentage weight values
Prc Percent CountHH Counter for too large
values
D Percent loss
Diff Check result measure
DR Ratio in percent 1
OR Ratio in percent 2 Motorized Draft Shield
WPC Draft shield version
Stat Draft shield status
InvTim Interval
FixTim Fixed point in time Ionizer
ResTim Remaining time Stat Ionizer status
Hold Display blocked

Interfaces
Data Input
SBI Commands (Data Input Format)
The computer connected via the data port can send control commands to the
balance to control balance and application program functions.
These control commands may have different formats and contain up to 26 charac-
ters. Each of these characters must be sent based on the setup configuration for
data transmission.
Formats for Control Commands

Format 1: Esc ! CR LF
Format 2: Esc ! # _ CR LF
Format 3: Esc ! # & (max. 20 &) & _ CR LF
Esc: Escape
!: Command character
#: Number
&: Number or letter
_: Underline (ASCII: 95)
CR: Carriage return (optional)
LF: Line feed (optional)
max: Depends on command character (parameters): The entry is truncated after
the max. length and not rejected as when entered via the keyboard.
Examples:
Format 1: Esc P
Format 2: Esc x1_
Format 3: Esc t Article1_
Format 4: Esc e!{MESSAGE.SHOW_ERROR “Weight too low!}_
Esc e?{DEVICE.CLMOD_MEAS_TEMP}
ESC e?{DEVICE.CLMOD_MEAS_PRESS} (e.g. Query climate data)
Esc ea{Art.413}_
(Determine weight and tare values and save to the alibi memory
together with the label)

Interfaces
Overview of SBI Commands

Format Command Action/Function Comments
1 ESC P Print to the interface where the prompt originated Corresp. to menu, with/without stability
1 ESC T “TARE“ key taring and zeroing
1 ESC K Filter “Very stable conditions”
1 ESC L Filter “Stable conditions”
1 ESC M Filter “Unstable conditions”
1 ESC N Filter “Very unstable conditions”
1 ESC O Block keys
1 ESC Q Acoustic signal
1 ESC R Unblock keys
1 ESC S Restart
1 ESC Z Internal calibration/adjustment Depending on menu, 1/2 step increments
1 ESC U Tare
1 ESC V Zero key
1 ESC W Ext. Adjustment with default weight Depending on menu, 1/2 step increments
2 ESC f3_ Zero
2 ESC f4_ Tare (without zeroing)
2 ESC f5_ Left draft shield key (closing and opening as learned or default) Only if available
2 ESC f6_ Right draft shield key (closing and opening as learned or default) Only if available
2 ESC kF1_ Softkey 1, first from right Depends on application
2 ESC kF2_ Softkey 2, second from right Depends on application
2 ESC kF3_ Softkey 3, third from right Depends on application
2 ESC kF4_ Softkey 4, fourth from right Depends on application
2 ESC kF5_ Softkey 5, fifth from right Depends on application
2 ESC kF7_ “Menu” softkey
2 ESC kF9_ “TASK” key
2 ESC kF10_ “USER” key
2 ESC kP_ Print as with “PRINT” key (e.g., to several interfaces)
2 ESC m0_ Ionizer status Only if available
2 ESC m1_ Ionizer on, with preset time Only if available
2 ESC m2_ Ionizer off Only if available
2 ESC s3_ Back, exit, cancel
Models with the Models with the Analytical and rotation
analytical draft shield rotation draft shield draft shield
2 ESC w0_ Draft shield status Draft shield status Only if available
2 ESC w1_ Open left door Open draft shield 100% to the left Only if available
2 ESC w2_ Close all doors Close draft shield Only if available
2 ESC w3_ Open upper door Open draft shield to saved position Only if available
2 ESC w4_ Open right door Open draft shield 100% to the right Only if available
2 ESC w5_ Open left and upper door – Only if available
2 ESC w6_ Open left and right door – Only if available
2 ESC w7_ Open right and upper door – Only if available
2 ESC w8_ Open all doors Only if available
2 ESC x0_ Perform internal calibration
2 ESC x1_ Print weigher type
2 ESC x2_ Print serial number
2 ESC x3_ Print balance software version
2 ESC x4_ Print softw. version of display and control unit
2 ESC x5_ Print user/device ID
2 ESC x6_ Print cal./adjust. weight ID
2 ESC x7_ Print batch ID
3 ESC txxx_ Input text
3 ESC txxx_ESC f5_ Entry of opening angle xxx in degrees for left key
3 ESC txxx_ESC f6_ Entry of opening angle xxx in degrees for right key
3 ESC z5xxx_ Entry device ID
3 ESC z6xxx_ Entry cal./adj. device ID
3 ESC z7xxx_ Entry measurement series ID
4 ESC e! {xxx}_ Execute application command, {xxx} = Task ID
4 ESC e? {Xxx}_ Query parameter, {xxx} = Parameter ID
4 ESC ea {xxx}_ Save weight value to alibi memory (with optional label), {x…x} = Memory ID

Interfaces
Microbalances with a weighing range greater than 30 g:

Print formates
The following functions can be output in 1 or 2 lines.
Output “1-line” print format

Select the following system setting: Interfaces: …: SBI operating mode
Output “2-line” print format

Select the following system setting: Interfaces: …: “Printer” operating mode
Format Command (input) Climate data: Action/Function

4 ESC c {DEVICE.CLMOD_MEAS_TEMP:0}_ Temperature measurement value
4 ESC c {DEVICE.CLMOD_MEAS_HUMID:0}_ Humidity measurement value
4 ESC c {DEVICE.CLMOD_MEAS_PRESS:0}_ Pressure measurement value
4 ESC c {DEVICE.CLMOD_MEAS_AIR_DENS:0}_ Air density measurement value
4 ESC c {DEVICE.CLMOD_UNC_TEMP:0}_ Uncertainty temperature value
4 ESC c {DEVICE.CLMOD_UNC_HUMID:0}_ Uncertainty humidity value
4 ESC c {DEVICE.CLMOD_UNC_PRESS:0}_ Uncertainty pressure value
4 ESC c {DEVICE.CLMOD_UNC_AIR_DENS:0}_ Uncertainty air density
4 ESC c {DEVICE.CLMOD_SERIAL_NO:0}_ Serial number
4 ESC c {DEVICE.CLMOD_MODEL_NO:0}_ Model
4 ESC c {DEVICE.CLMOD_VERSION:0}_ Version
4 ESC c {DEVICE.CLMOD_CAL_LAB_TEMP:0}_ Calibration lab temperature sensor
4 ESC c {DEVICE.CLMOD_CAL_CER_TEMP:0}_ Calibration certificate temperature sensor
4 ESC c {DEVICE.CLMOD_CAL_DAT_TEMP:0}_ Calibration certificate temperature sensor
4 ESC c {DEVICE.CLMOD_CAL_LAB_HUMID:0}_ Calibration lab humidity sensor
4 ESC c {DEVICE.CLMOD_CAL_CER_HUMID:0}_ Calibration certificate humidity sensor
4 ESC c {DEVICE.CLMOD_CAL_DAT_HUMID:0}_ Calibration certificate humidity sensor
4 ESC c {DEVICE.CLMOD_CAL_LAB_PRESS:0}_ Calibration lab pressure sensor
4 ESC c {DEVICE.CLMOD_CAL_CER_PRESS:0}_ Calibration certificate pressure sensor
4 ESC c {DEVICE.CLMOD_CAL_DAT_PRESS:0}_ Calibration date pressure sensor
Select climate module or temp. sensor:

“0” internal climate module, 1 = Ext. climate module or 2 = Ext. temp. sensor
Only for internal climate module:

Format Command (input) Action/Function
2 ESC ca1_ Temperature measurement value
2 ESC ca2_ Humidity measurement value
2 ESC ca3_ Pressure measurement value
2 ESC ca5_ Air density measurement value
2 ESC ca6_ Uncertainty temperature value
2 ESC ca7_ Uncertainty humidity value
2 ESC ca8_ Uncertainty pressure value
2 ESC ca10_ Uncertainty air density
2 ESC ca11_ Serial number
2 ESC ca12_ Model
2 ESC ca13_ Version
2 ESC ca14_ Calibration lab temperature sensor
2 ESC ca15_ Calibration certificate temperature sensor
2 ESC ca16_ Calibration certificate temperature sensor
2 ESC ca17_ Calibration lab humidity sensor
2 ESC ca18_ Calibration certificate humidity sensor
2 ESC ca19_ Calibration certificate humidity sensor
2 ESC ca20_ Calibration lab pressure sensor
2 ESC ca21_ Calibration certificate pressure sensor
2 ESC ca22_ Calibration date pressure sensor
Example of the internal climate module, temperature measurement value:

ESC ca1_
or
ESC c {DEVICE.CLMOD_MEAS_TEMP:0}_
Interfaces
SICS and Mini-SICS Commands

The computer connected via the data port can send control commands to the
balance to control balance and application program functions.
h Please consult the separate SICS documentation for a description of the syntax.
1) Some labeled commands can also be mini-SICS commands.
Command Action/Function
Level 0 Version 2.3x
@ Reset all SICS commands
I0 List all available commands
I1 Send information about the level and its versions
I2 Balance model prompt
I3 Prompt for input of software version of balance (BAC)
I4 Prompt for balance serial number
I5 Prompt for software version of display (APC)
S1) Send weight value at stability
SI1) Send weight value without stability
SIR1) Send automatic weight values at and without stability
Z Zero the balance at stability
ZI Zero the balance without stability
Level 1 Version 2.2x
T1) Tare the balance at stability
TI1) Tare the balance without stability
D Write text in display
DW Delete text from display
K Key control
TA Prompt for and allocate tare memory
TAC Delete tare memory
SR Send weight value if weight changes
Level 2
SU Send weight value at stability with current weight unit (with motorized draft shield)
WS Query door position of motorized draft shield / Open or close door
PWR Turn balance on/off (standby)
I10 Query/set the balance ID
I11 Query balance type
I14 Query balance components
M01 Query/set application filter
M02 Query/set filter adjustment
M03 Query/set automatic zeroing
M04 Query/set I/O inputs
M07 Query/activate/deactivate automatic draft shield
M12 Acoustic signal (beep)
M13 Activate/deactivate touch screen softkeys
M21 Query/set unit of weight
M24 Query/deactivate “Print” key / Print the stable or unstable weight values
M39 Query/activate bar graph display in working environment
P100 Send text line to printer
C1 Execute calibration/adjustment (as set in menu)

Interfaces
Remote control (remote)

P112 Write text in selected line on display
P113 Delete text from selected line in display
P114 Overwrite task or user names
P120 Turn off bar graph in checkweigher
P121 Turn on bar graph in checkweigher
RM20 Activate/deactivate user input
RM30 Assign new function to softkeys
RM32 Assign new order to softkeys
RM34 Create a dynamic parameter
RM35 Immediately change softkey designations
RM36 Assign/prompt for function of multiple softkey lines
RM37 Prepare preset softkey designations for display
RM38 Activate RM36-assigned softkey lines
RM39 Activate/deactivate RM30-assigned softkey functions
RM44 Query/set input with barcode scanner
RM48 Change order of standard keys
RM49 Activate/deactivate message
RM51 Activate/deactivate selection window
RM52 Define properties for a window with info text
RM53 Activate/deactivate window with info text
RM54 Activate / deactivate info window
Additional Sartorius Commands

SA Send weight value at stability and store in alibi memory (with optional label)
CMD Execute application command
PAR Query parameter
MN36 Assign a description to several menus
MN38 Activate/deactivate MN36-assigned menus
TX36 Assign texts to several text pages
TX37 Overwrite a line of a text page
TX38 Activate/deactivate TX38-assigned text pages


Purpose: To better serve our customers, Sartorius constantly improves its balance software.
Sartorius makes the latest software versions available online so that you can quickly
and easily remain up-to-date. Sartorius, however, makes no guarantee regarding
the use of this software.
The software should only be updated by an administrator.
On verified balances, observe the Audit Trail instructions under

(3) Upload the Software Update to the Balance.
3 Before updating the software, save all data (see Section Exporting Data).
h If you are working with User Management (user profiles are defined), the software
can only be updated by the administrator.
1) Download the Software Update from the Internet

The first step is to download the software to your computer:
t In your browser, go to
“www.sartorius.com/downloads” and click on the “Software” link.
t Select the update package for your balance.
t Enter the information required for registration.
t Download the software package to your computer.
t Unzip the file.
t Copy the software update to an SD card (32 + 24 + 2.1 mm).
2) Insert the Memory Card into the Control Unit

The slot for the SD card is located at the back of the control unit.
1 2
1. Tilt the display and control unit.

2. Swivel the cover of the card slot to the front.
Align the SD card so that the contacts are facing forward.
3. Insert the card into the slot as far as it will go.
t To remove the card, press it down into the slot so that the card springs out.

3) Upload the Software Update to the Balance

t If you are working with User Management (user profiles are defined),
the software can only be updated by the administrator.
t Toggle to the System Settings menu.
t Open the Update software submenu.
y You are asked if you want to delete the existing profiles.

t Select No or Yes.
t Once the SD card with the current software is inserted, select Next.
If the following error message appears:

Wrong XML version. Please check the data.
t Touch Next.
y All previous data will be saved in the new format.
t After updating your software, check your settings (Menu, TASK and USER).
t If the XML files continue to cause problems, contact your local Sartorius
Service Center.
y After a version check is run, the versions of the current and the new software
are displayed.
t To start the update, select Continue.
y An acoustic signal will sound when the update is complete, and the balance
then carries out a self test.
Audit Trail for Software Download on Models Verified for Legal

Metrology
Software Status of the Balance
Models verified for use in legal metrology are assigned an authorized software
status when the balance is shipped for delivery. This can be indicated on the display.
If something concerning the software or the legal regulations changes, the software
status must be updated.
Displaying the Audit Trail of the Balance Software
t Turn off the balance and disconnect it from the power supply.
t Hold down A and reconnect the balance to the power supply.
y The “Bios” menu is displayed.
t Press the “Show settings” menu item.
t Select the “Audit trail of software updates” menu item.
t Select “Show audit trail.”
y The Audit Trail with modification date, name, new and old software,
and version number are indicated on the display.

Error and Status Messages
Error and Status Messages

Error messages appear directly in the respective active application, usually with
descriptive text on how to correct it. Warning and reminder functions are displayed
with a fixed 3-level action hierarchy:
Status Display (Tab):

The available status displays and their meanings are described in the “Display”
section.
Warning Text with a Repeated Reminder
Error Text with Mandatory Prompt for Troubleshooting

You cannot proceed until you have eliminated the error.
Ineffective Key Commands or Entries

If you press a key that has no function or is not allowed, this error is indicated
as follows:
– An error message indicates invalid input.
– An error code or error message indicates incorrect operation.
Error messages are shown on the display for two seconds or must be acknowledged
by pressing a key. The error text provides direct suggestions on how to proceed.
If the error cannot be resolved by following the suggestions, please contact
Sartorius customer service.

GPL License
GPL License
Devices of the Cubis® series also contain “free software” in the firmware that is
licensed under the GNU General Public License (GPL) Version 2, June 1991 and the
GNU Lesser General Public License (LGPL) Version 2.1, February 1999. This third-
party developed “free software” is copyrighted and is provided free of charge.
The licensing conditions of the Free Software Foundation, Inc. are available in
English on the included CD-ROM.
You can purchase the GPL source text from Sartorius on CD under the
VF no. VF 4043 for a shipping cost of ¤ 20.00.

Care and Maintenance

Service
Regular servicing by a Sartorius technician will extend the service life of your bal-
ance and ensure its continued weighing accuracy. Sartorius offers its customers ser-
vice contracts with regular maintenance intervals ranging from 1 month to 2 years.
The frequency of the maintenance intervals depends on the operating conditions
and user’s tolerance requirements.
Repairs
Repair work must only be carried out by trained service technicians. Repairs per-
formed by untrained persons may result in considerable hazards for the user.
3 The device must be unplugged during repair work.

Unplug the power cord from the outlet.
Repair work must only be performed b y Sartorius-trained service
technicians.
If required: Please contact your Sartorius dealer!
Cleaning the Balance
3 Ensure that no dust or liquid enters the balance weighing system.
Do not use aggressive cleaning agents (solvents or similar).
Isolate from supply voltage: Unplug the power cord from the wall outlet
and unplug any data cables connected to the balance.
t Open the panels of the analytical draft shield completely.
t Clean the housing and interior of the balance with a cloth lightly moistened
with a soap solution.
t Dry all parts with a soft, dry cloth or use blotting paper to absorb dampness.
Then replace all dried parts.
t Remove panels from the analytical draft shield and clean them with commer-
cially available glass cleaner. Dry the panels.
Then reinstall them to the balance.

t Carefully remove any sample residue/spilled powder using a brush or hand-held

vacuum cleaner.
t If necessary, remove the weighing pan, shield plate, and pan support.
1
1. Weighing pan
2
3 3. Pan support
t Clean parts with a cloth or brush.

Then replace the parts.

Cleaning the Stainless Steel Weighing Pan

All stainless steel parts should be cleaned at regular intervals.
Use a damp cloth or sponge to clean stainless steel parts on the balance.
Only use conventional household cleaning agents which are suitable for stainless
steel (e.g. Stahlfix). After this, let the device dry.
For additional protection, protective oil may be applied.
Remove the stainless steel weighing pan and thoroughly clean it separately.
Only use solvents for cleaning stainless steel parts.
The stainless steel weighing pan should be cleaned simply by rubbing.
After this, rinse the equipment thoroughly until all residue is removed.
No protective oil should be applied to the stainless steel weighing pan.
Cleaning the Weighing Chamber of Balances with a readability of ) 1 μg

t Carefully remove any powdered sample material from beneath the shield disk
using a small car vacuum cleaner with an mini-hose attached.
t Use blotting paper to remove any liquid sample material.
3 Do not insert forceps or similar utensils behind the draft shield plate.
Note: The weighing system is hermetically separated from the area of the draft
shield plate. This prevents spillage or other impurities from entering.

Safety Inspection
If there is any indication that safe operation of the balance is no longer warranted:
t Disconnect from the supply voltage: Unplug the power cord from the outlet.
t Secure the AC adapter and cord so that they cannot be used.
Safe operation of the AC adapter is no longer ensured:
– When the AC adapter or the power cord shows visible damage.

– When he AC adapter no longer functions properly.
– Following extended storage in adverse conditions.
In this case, notify the Sartorius Service Center.
Maintenance and repair work may be performed only by authorized service

technicians who have access to the required maintenance manuals and instruc-
tions and who have received the necessary training.
We recommend that the AC adapter be inspected by a qualified service technician

with regard to the following:
– Leakage current: <0.25 mA measured with a properly calibrated multimeter.

– Insulation resistance >SOhm as measured with a constant voltage of at least
500 volts at a 500 kOhm load.
The duration and number of checks should be determined by a qualified Sartorius

service technician on site based on specific ambient and operating conditions
(once a year as a minimum).

Storage and Shipping

Storage and Shipping Conditions
– Permitted storage and shipping temperature: -10 to +60°C
– Unpacked devices can lose their precision if subjected to extreme vibrations.
– Excessive vibrations may compromise the safety of the equipment.
Save the packaging for any future storage or shipment of the balance.
Only the original packaging provides optimum protection for the equipment.
– Follow all warnings and safety precautions.
Transporting or Shipping the Device over Long Distances
t Switch the device to standby mode.
t Disconnect the device from the power supply.
t Disconnect any data cables from the device.
Models MSU116P, MSU66, MSU36:

Always use the complete original packaging:
− Whenthe device is to be transported over long distances or shipped.
− If you are unsure whether or not the device will be transported upright.
t Remove the following parts:

− Inner draft shield
− Shield disk
− Weighing pan and shield plate:
Reach beneath the shield plate and lift it up carefully in a vertical position
together with the weighing pan to avoid damaging the weighing system.
t Open the draft shield doors and carefully position the device in the lower
packaging padding.
t Push the inner foam padding against the housing.

t Attach the retainers to the panel.
t Place the shield disk into a bag.
t Position the lateral packaging padding around the device and press inward.
t Place the following parts in the recessed spaces:

− Shield plate
− Weighing pan
− Inner draft shield
t Wrap the cardboard sleeve around the inner packaging.

t Place the holding strap around the cardboard sleeve and pull it
tight.
t Lift the packaged device by the strap and place it in the shipping box in the
bottom packaging padding.
t Place the upper packaging padding on top.
t Close the outside shipping box and seal it appropriately.
Box:
t Place the control unit into the bottom packaging padding.
t Place the upper packaging padding on top.
t Pack the display unit into the small cardboard box.
t Pack the weigh cell cardboard box and the display unit cardboard box into the
large outside box.
t Ship the packaged device.

Models with the Analytical Draft Shield:

t Remove all items (such as weights, sensors, etc.) from the weighing chamber.
1) Remove one side draft shield panel
4 2) Remove the other side draft shield panel
3) Remove the upper draft shield panel
5 4) Remove the weighing pan
6 5) Remove the pan support (not for MSU225.../MSU125... models)
3 6) Remove the shield plate/draft shield
1
t On models without a draft shield: press down on the two pan support
fasteners.
t Rotate and remove the pan support.
t Place the balance in the lower part of the packaging.

Transporting the Parts (Large Analytical Draft Shield)
t Get the box for the individual parts of the balance ready.
t Place the bottom foam piece in the box.
t Place the panels in the packaging:

1) Place the upper draft shield panel into the packaging (handle upwards).
3 2 2) Place the side draft shield panel into the packaging (handle upwards).
3) Place the other side panel into the packaging (handle downwards).
t Then place the top foam piece in the box.

For a small weighing pan:

t Place the shield plate into the box.
t Place the pan support and weighing pan into the opening.
t Close the box.
For a large weighing pan:

t Place the following parts into the foam piece in the order given:
1) Shield plate
2) Pan support
3) Weighing pan
t Close the box.

Transporting the Parts (Small Analytical Draft Shield)
t Get the box ready for the individual parts of the balance.
t Get the foam pieces ready.
t Place the balance parts on top of each other

1) Upper draft shield panel
2) Shield plate/draft shield
3) Pan support
3
2
1
t Slide the parts into the foam.

t Place the panels in the packaging.

1) Place the side draft shield panel into the packaging (handle downwards).
2) Place the side draft shield panel into the packaging (handle downwards).
t Place the foam piece in front of the parts.
t Place the package into the box.
t Slide the shield plate into the packaging.

t Close the box.
t Place the box into the packaging.
t Place the top part on to the packaging.
t Insert the balance into the box with cushioning.
t Send the packaged balance.

Disposal
Disposal
Information on Decontamination
The device does not contain any hazardous materials that would necessitate special
disposal measures. The contaminated samples used in the process are potentially
hazardous substances that can cause biological or chemical hazards.
If the device has come into contact with hazardous substances: Measures must be
carried out to properly decontaminate and declare such devices. The operator is
responsible for adhering to local legislation on the proper declaration of
transportation and disposal and the proper disposal of the device.
WARNING
Danger of injury due to contaminated equipment!
Devices contaminated with hazardous materials (ABC contamination) will not be
accepted by Sartorius for repair or disposal.
Disposing of Device and Parts
Information on Disposal
The device and its accessories do not belong in regular household waste, since they
are made of high-grade materials that can be recycled and reused. All parts must be
disposed of properly by disposal facilities.
A lithium cell battery is installed inside the device. Batteries do not belong in regular
household waste since they are made of high-grade materials that can be recycled
and reused. Batteries must be disposed of properly by disposal facilities. The
packaging consists of environmentally friendly materials that can be used as
secondary raw materials.
Disposal
Requirements
The device has been decontaminated.
Procedure
Dispose of the device. Follow the disposal instructions on our website (www.sartorius.
com). Inform the disposal facility that a lithium cell battery is installed in the device.
Dispose of the packaging in accordance with local government regulations.

Technical Data
Technical Data
General Data
Sartorius power supply Model 6971987

Primary 100 – 240 V~, –15%/+10%, 50–60 Hz, 1.0 A
Secondary 15 V, ± 5%, 2.66 A (max.), protected electronically against short circuit
Other data Protection class II as per EN/IEC 60950-1 | up to 3000 m above sea level | IP40 as
per EN 60529/IEC 60529
Power supply connection cable Two-sided plug with a 3-pin country-specific power plug and 3-pin socket
(IEC/EN60320-1/C14) for connection to the power supply
Other data See the power supply label
Balance
Power supply Only via Sartorius adaptor 6971987
Input voltage 15 VDC, ± 5%
Power consumption 7 W (max.)
IP protection for models
with a readability of * 10 mg IP54 as per EN 60529/IEC 60529
Ambient Conditions
Environment For indoor use only
Storage and shipping temperature –10 °C to +60 °C
Ambient temperature, operation* +5 °C to +40 °C
Height Up to 2000 m above sea level
Maximum relative humidity** 80 % for temperatures up to 31 °C, decreasing linearly up to 50%
relative humidity at 40 °C
Safety of Electrical Equipment According to EN 61010-1:2010

Safety requirements for electrical equipment for measurement, control and
laboratory use – Part 1: General requirements
Electromagnetic Compatibility as per EN 61326-1:2013

Electrical equipment for measurement, control, and laboratory use
EMC requirements – Part 1: General requirements
Interference resistance Suitable for use in industrial areas
Interference emission Class B: (Suitable for use in residential areas and areas that are connected to a low
voltage network that also supplies residential buildings).
-.CE model balances verified for use in legal metrology comply with the requirements of Council Directive No.
2014/31/EU with EN 45501:2015 and OIML R76:2006.
* For -.CE model balances verified for use in legal metrology, refer to the information on the balance.
** For -.CE model balances verified for use in legal metrology, the legal regulations apply.

Technical Data
Model-specific Data
Microbalances 0.001mg
Model MSU6.6S MSU6.6S-F MSU3.6P
Readability mg 0.001 0.001 0.001/0.002/0.005
Weighing capacity g 6.1 6.1 1.1/2.1/3.1
Tare range (subtractive) g –6.1 –6.1 –3.1
Repeatability <±mg 0.001 0.001 0.003/0.004/0.005
Linearity <±mg 0.004 0.004 0.004
Corner load (test load [g]) mg 4 (2 g) 4 (2 g)* 5 (1 g)
Min. initial weight mg 2 – 4
Sensitivity drift between +10...+30°C ±ppm/K 1 1 1
Typical stabilization time s <5 <5 <5
Typical measurement time s <8 <8 <8
External standard calibration value g 5 (E2) 5 (E2) 3 (E2)
(min. accuracy class)
Display result
(depending on the set filter level) 0.1 – 0.4 0.1 – 0.4 0.1 – 0.4
Weighing pan size d mm 30 50 30
Weighing chamber height mm 70 – 70
Protection Protected against dust and water
Ultra-Microbalances 0.0001mg
Model MSU2.7S MSU2.7S-F
Readability mg 0,0001 0,0001
Weighing capacity g 2.1 2.1
Tare range (subtractive) g –2.1 –2.1
Repeatability <±mg 0.00025 0.00025
Linearity <±mg 0.0009 0.0009
Corner load (test load [g])1) mg 2.5 (1) 2.5 (1)
Min. initial weight mg 1 –
Sensitivity drift between zw. +10...+30°C ±ppm/K 1 1
Typical stabilization time s <7
Typical measurement time s < 10
External standard calibration value g 2 (E2) 2 (E2)
Display result
(depending on the set filter level) 0.1 – 0.4 0.1 – 0.4
Weighing pan size d mm 20 50
Weighing chamber height mm 70 15
1) = Standard pan
2) Typical min. initial weighing according to USP (United States Pharmacopeia), USP31-NF26

Technical Data
Model-specific Data
High-capacity microbalances
Models MSU66S MSU66P MSU36S MSU36P MSU116P
Readability mg 0.001 0.001/0.01 0.001 0.001/0.01 0.002/0.01
Weighing capacity g 61 12/61 31 31/6 12/111
Tare range (subtractive) g 61 61 31 31 111
Reproducibility (100 g/5 g) <±mg – – – – 0.01/0.004
Reproducibility (50 g/2 g) <±mg 0.004/0.0015 0.010/0.002 – – –
Reproducibility (20 g/1 g) <±mg – – 0.002/0.0015 0.008/0.0015 –
Linearity <±mg 0.02 0.02 0.015 0.015 0.02
Corner load (test load [g]) mg 0.02 (20) 0.02 (20) 0.015 (10) 0.015 (10) 0.03 (50)
Optimal min. initial weight mg 0.82 0.82 0.82 0.82 1.64
Sensitivity drift between +10 to +30°C ±ppm/K 1 1 1 1 1
Typical stabilization time s 3.5 3.5 3.5 3.5 3.5
Typical measurement time s 10 10 10 10 10
External standard calibration value g 50 (E2) 50 (E2) 20 (E2) 20 (E2) 100 (E2)
Display result s 0.2 – 0.4 0.2 – 0.4 0.2 – 0.4 0.2 – 0.4 0.2 – 0.4
(depending on the set filter level)
Weighing plan size d mm 30/50* 30/50* 30* 30* 50**
Weighing chamber height mm 181 181 181 181 240
* = The technical weighing specifications refer to the weighing pan with d = 30 mm.
** = The technical weighing specifications refer to the weighing pan with d = 50 mm.
Semi-microbalances 0.01 mg
Model MSU225S MSU225P MSU125P
Readability mg 0.01 0.01/0.02/0.05 0.01/0.1
Weighing capacity g 220 60/120/220 60/120
Tare range (subtractive) g – 220 – 220 – 120
Repeatability <±mg 0 to 6 g: 0.015 0 to 6 g: 0.015 0 to 6 g: 0.015
60 to 220g: 0.025 60 to 220g: 0.04 60 to 120g: 0.06
Linearity <±mg 0.1 0.15 0.15
Corner load (test load [g]) mg 0.15 (100) 0.2 (100) 0.15 (50)
Min. initial weight* mg 20 20 20
Sensitivity drift between +10 to +30°C ±ppm/K 1 1 1
Typical stabilization time s < 2 < 2 <2
Typical measurement time s < 6 < 6 <6
Display result
(depending on the set filter level) 0.2 – 0.4
Weighing pan size (W + D) mm 85 + 85
Weighing chamber height (draft shield DU) mm 261
* = Typical min. initial weighing according to USP (United States Pharmacopeia), USP31-NF26

Technical Data
Model-specific Data
Analytical balances 0.1 mg

Model MSU524S MSU524P MSU324S MSU224S MSU324P MSU124S
Readability mg 0.1 0.1/0.2/0.5 0.1 0.1 0.1/0.2/0.5 0.1
Weighing capacity g 520 120/240/520 320 220 80/160/320 120
Tare range (subtractive) g – 520 – 520 – 320 – 220 – 320 – 120
Repeatability <±mg 0.1 0.15/0.2/0.4 0.1 0.07 0.1/0.2/0.4 0.1
Linearity <±mg 0.4 0.5 0.3 0.2 0.5 0.2
Corner load (test load [g]) mg 0.3 (200) 0.4 (200) 0.3 (200) 0.2 (100) 0.4 (200) 0.2 (50)
Min. initial weight* mg 120 120 120 120
Sensitivity drift between +10 to +30°C ±ppm/K 1 1 1 1 1 1
Typical stabilization time s <1 <1 <1 <1 <1 <1
Typical measurement time s <3 <3 <3 <3 <3 <3
External standard calibration value g 500 500 200+100 200 (E2) 200+100 100 (E2)
(min. accuracy class) (E2) (E2)
Display result
Precision balances
Models MSU5203S MSU5203P MSU3203S MSU3203P
Readability mg 1 1/2/5 1 1/10
Weighing capacity g 5200 1200/2400/5200 3200 1010/3200
Tare range (subtractive) g - 5200 - 5200 – 3200 – 3200
Repeatability <±mg 1 1 1 1/6
Linearity <±mg 5 5 5 5
Corner load (test load [g]) mg 2 (2000) 2 (2000) 2 (1000) 2 (1000)
Min. initial weight* g 1.5
Sensitivity drift between +10 to +30°C ±ppm/K 1 1 1 1
Typical stabilization time s <1 <1 <1 <1
Typical measurement time s <2 <2 <2 < 1.5
External standard calibration value g 5000 5000 2000 2000 (E2)
Display result
Weighing chamber height
(draft shield DE) mm 172
* = Position according to OIML R76

Technical Data
Model-specific Data
Models MSU2203S MSU2203P MSU1203S

Readability mg 1 1/10 1
Weighing capacity g 2200 1010/2200 1200
Repeatability <±mg 1 1/6 0.7
Linearity <±mg 3 5 2
Corner load (test load [g]) mg 2 (1000) 3 (1000) 2 (500)
Min. initial weight* g 1.5 1.5 1.5
Sensitivity drift between +10 to +30°C ±ppm/K 1 1 1.5
Typical measurement time s < 1.5 < 1.5 < 1.5
Display result
Precision balances
Models MSU623S MSU623P MSU323S
Readability mg 1 1/2/5 1
Weighing capacity g 620 150/300/620 320
Repeatability <±mg 0.7 1/2/4 0.7
Linearity <±mg 2 5 2
Corner load (test load [g]) mg 2 (200) 4 (200) 2 (200)
Min. initial weight* g 1.5 1.5 1.5
Sensitivity drift between +10 to +30°C ±ppm/K 2 2 2
Typical stabilization time s < 0.8 < 0.8 < 0.8
External standard calibration value g 500 (E2) 500 (F1) 200 (E2)
Display result

Technical Data
Model-specific Data
Models MSU14202S MSU14202P MSU10202S MSU8202S

Readability mg 10 10/20/50 10 10
Weighing capacity g 14,200 3500/7000/14,200 10,200 8200
Tare range (subtractive) g - 14,200 - 14,200 – 10,200 – 8200
Repeatability <±mg 10 10/20/40 7 7
Min. initial weight* g 15 15 12 12
Sensitivity drift between +10 to +30°C ±ppm/K 1.5 1.5 2 2
Typical measurement time s < 1.5 < 1.5 < 1.5 < 1.5
External standard calibration value kg 10 (E2) 10 (E2) 10 (E2) 5 (E2)
Display result
Precision balances
Models MSU6202S MSU6202P MSU5202S MSU4202S
Readability mg 10 10/20/50 10 10
Weighing capacity g 6200 1500/3000/ 5200 4200
6200
Tare range (subtractive) g – 6200 – 6200 - 5200 – 4200
Repeatability <±mg 7 7/20/40 6 7
Typical stabilization time s <1 <1 < 0.8 < 0.8
Typical measurement time s << 1.5 < 1.5 <1 <1
External standard calibration value kg 5 (E2) 5 (F1) 5 2 (E2)
Display result
Weighing pan size (W + D) mm 206 + 206 206 + 206 140 + 140 206 + 206

Technical Data
Model-specific Data
Precision balances
Models MSU2202S MSU1202S MSU70201S MSU36201S MSU36201P
Readability mg 10 10 100 100 100/1000
Weighing capacity g 2200 1200 70,200 36,200 10,200/36,200
Tare range (subtractive) g – 2200 – 1200 – 70,200 – 36,200 – 36,200
Repeatability <±mg 7 7 70 70 70/500
Linearity <±mg 20 20 500 200 200
Corner load (test load [g]) mg 20 (1000) 20 (500) 500 (20,000) 300 (10,000) 300 (10,000)
Min. initial weight* g 12 12 120 120 120
Sensitivity drift between +10 to +30°C ±ppm/K 2 2 3 2 2
Typical stabilization time s < 0.8 < 0.8 <1 <1 <1
Typical measurement time s <1 <1 < 1,5 < 1,5 < 1,5
External standard calibration value kg 2 (F1) 1 (F1) 50 (F1) 20 (F1) 20 (F1)
Display result
Weighing pan size (W + D) mm 206 + 206 206 + 206 400 + 300 400 + 300 400 + 300
Protection IP54
Precision balances
Models MSU20201S MSU12201S MSU8201S MSU5201S
Readability mg 100 100 100 100
Weighing capacity g 20,200 12,200 8200 5200
Tare range (subtractive) g – 20,200 – 12,200 – 8200 – 5200
Repeatability <±mg 70 50 50 50
Linearity <±mg 200 100 100 100
Typical stabilization time s <1 < 0.8 < 0.8 < 0,8
Typical measurement time s < 1,5 <1 <1 <1
External standard calibration value kg 20 (F1) 10 (F1) 5 (F2) 5 (F2)
Display result
Protection IP54

Technical Data
Model-specific Data
Precision balances
Models MSU70200S MSU36200S
Readability mg 1000 1000
Weighing capacity g 70,200 36,200
Tare range (subtractive) g – 70,200 – 36,200
Repeatability <±mg 500 500
Linearity <±mg 1000 1000
Corner load (test load [g]) mg 1000 (20,000) 1000 (10,000)
Min. initial weight* g 1000 1000
Sensitivity drift between +10 to +30°C ±ppm/K 3 2
Typical stabilization time s < 0.8 < 0.8
Typical measurement time s <1 <1
External standard calibration value kg 50 (F1) 20 (F1)
Display result
Protection IP54
Verified Models with EC Type Approval Certificate: Micro- and ultramicrobalances

Model MSU6.6S-0CE MSU2.7S-0CE MSU3.6P-0CE
Accuracy class* k k k
For verified models: EC Type Approval Certificate D09-09-015, Type: MSX
Scale interval d* mg 0.001 0.0001 0.001/0.002/0.005
Weighing capacity Max* g 6.1 2.1 3.1
Calibration value e* mg 1 1 1
Min. load Min* mg 0.1 0.01 0.1
Tare equalization range (subtractive) < 100 % from max. weighing capacity
Application range according to DIR* g 0.001 – 6.1 0.001 – 2.1 0.001 – 3.1
Min. initial weight** mg 2 1 4
Typical measurement time s <8 < 10 <8
External standard calibration value
(min. accuracy class) g 5 2 3
Application range (temperature) With “isoCAL” function: +5…+40°C |
Without “isoCAL” function: +15 … +25°C
Display result (depending on the set filter level) By selection of 1 of 4 optimized filter levels
Weighing pan size d mm 30 20 30
(draft shield DM) mm 70 70 70
* DIR = Directive 2014/31/EU on non-automatic weighing instruments used within the European Economic Area
** = Typical min. initial weighing according to USP (United States Pharmacopeia), USP31-NF26

Technical Data
Model-specific Data
Verified Models with EC Type Approval Certificate: High-capacity microbalances

Models MSU66S- MSU66P- MSU36S- MSU36P- MSU116P-
0CE 0CE 0CE 0CE 0CE
Accuracy class* k k k k k
For verified models: EC Type Approval Certificate DE-17-NAWID-PTB021, Type: MSY
Digits d* mg 0.001 0.001 / 0.01 0.001 0.001 / 0.01 0.002 / 0.01
Weighing capacity Max* g 61 12 / 61 31 6 / 31 12 / 111
Verification scale interval e* mg 1 1 1 1 1
Min. load, Min* mg 0.1 0.1 0.1 0.1 0.2
Tare equalization range (subtractive) < 100% from max. weighing capacity
Application range according to DIR * g 0.0001 – 61 0.0001 – 61 0.0001 – 31 0.0001 – 31 0.0002 – 111
Min. initial weight** g 0.82 0.82 0.82 0.82 1.64
Typical stabilization time s 3.5 3.5 3.5 3.5 3.5
Typical measurement time s 10 10 10 10 10
Application range (temperature) with “isoCAL” function: +10 to +30 °C | without “isoCAL” function: +15 to +25 °C
Display result
Weighing plan size d mm 30/50 30/50 30 30 50/90
IPprotection Protected against dust and water
Verified Models with EC Type Approval Certificate: Semimicrobalances 0.01 mg

Model MSU225S-0CE MSU225P-0CE MSU125P-0CE
For verified models: EC Type Approval Certificate D09-09-015, Type: MSX
Digits d* mg 0.01 0.01/0.02/0.05 0.01/0.1
Weighing capacity Max* g 220 60/120/220 60/120
Verification scale interval e* mg 1 1 1
Min. load, Min* mg 1 1 1
Application range according to DIR * g 0.001 – 220 0.001 – 220 0.001 – 120
Min. initial weight** mg 20 20 20
Typical stabilization time s < 2 < 2 <2
Typical measurement time s < 6 < 6 <6
Application range (temperature) with “isoCAL” function: +5 to +40°C | without “isoCAL” function: +15 to +25 °C
Adaptation to ambient conditions 4 optimized filter levels
Display result (depending on the set filter level) 0.2 – 0.4
Weighing chamber height (DU draft shield) mm 261

Technical Data
Model-specific Data
Verified models with EC Type Approval Certificate: Analytical balances 0.1 mg

Model MSU524S- MSU524P- MSU324S- MSU224S- MSU324P- MSU124S-
0CE 0CE 0CE 0CE 0CE 0CE
Accuracy class* k k k k k k
For verified models: EC Type-Approval Certificate D09-09-015, Type: MSX
Scale interval d* mg 0.1 0.1/0.2/0.5 0.1 0.1 0.1/0.2/0.5 0,1
Weighing capacity Max* g 520 120/240/520 320 220 80/160/320 120
Calibration value e* mg 1 1 1 1 1 1
Min. load Min* mg 10 10 10 10 10 10
Application range according to DIR* g 0.01–520 0.01–520 0.01–320 0.01–220 0.01–320 0.01–120
Min. initial weight** mg 120 120 120 120 120 120
Typical stabilization time s <1 <1 <1 <1 <1 <1
Typical measurement time s <3 <3 <3 <3 <3 <3
External standard calibration value g 500 500 200+100 200 200 +100 100
(min. accuracy class) (E2) (E2) (E2) (E2)
Application range (temperature) With “isoCAL” function: +5 to +40 °C | Without “isoCAL” function: +15 to +25 °C
Display result (depending on the set filter level) 0.1 – 0.4
Verified models with EC Type Approval Certificate: Precision balances

Models MSU5203S-0CE MSU5203P-0CE MSU3203S-0CE MSU3203P-0CE
Accuracy class* k k k k
Scale interval d* mg 1 1/2/5 1 1/10
Weighing capacity Max* g 5200 1200/2400/5200 3200 1010/3200
Calibration value e* mg 10 10 10 10
Min. load Min* mg 100 100 100 100
Application range according to DIR* g 0.1 – 5200 0.1 – 5200 0.1 – 3200 0.1 – 3200
Min. initial weight** g 1.5 1.5 1.5 1.5
Typical measurement time s <2 <2 <2 < 1.5
External standard calibration value g 5000 5000 2000 2000 (E2)
Display result
Weighing chamber height (draft shield DE) mm 172

Technical Data
Model-specific Data
Models MSU2203S-0CE MSU2203P-0CE MSU1203S-0CE

Scale interval d* mg 1 1/10 1
Weighing capacity Max* g 2200 1010/2200 1200
Min. load Min* mg 100 100 100
Application range according to DIR* g 0.1 – 2200 0.1 – 2200 0.1 – 1200
Min. initial weight** g 1.5 1.5 1.5
Typical measurement time s < 1.5 < 1.5 < 1.5
Application range (temperature) With “isoCAL” function: +5 ... +40 °C
Without “isoCAL” function: +15 ... +25 °C
Display result
Weighing chamber height (draft shield DE) mm 172

Models MSU623S-0CE MSU623P-0CE MSU323S-0CE
Accuracy class* K K K
For verified models: EG-Type-Approval Certificate D09-09-015, Type: MSX
Scale interval d* mg 1 1/2/5 1
Weighing capacity Max* g 620 150/300/620 320
Min. load Min* mg 20 20 20
Application range according to DIR* g 0.02 – 620 0.02 – 620 0.02 – 320
Min. initial weight** g 1.5 1.5 1.5
Typical stabilization time s < 0.8 < 0.8 < 0.8
Display result
Weighing chamber height (draft shield DE)) mm 172

Technical Data
Model-specific Data
Models MSU14202S- MSU14202P- MSU10202S- MSU8202S-

0CE 0CE 0CE 0CE
Accuracy class* k k K K
Scale interval d* g 0.01 0.01/0.02/0.05 0.01 0.01
Weighing capacity Max* g 14,200 3500/7000/ 10,200 8200
14,200
Calibration value e* g 0.1 0.1 0.1 0.1
Min. load Min* g 1 1 1 0.5
Application range according to DIR* g 1 – 14,200 1 – 14,200 1 – 10,200 0.5 – 8200
Min. initial weight** g 15 15 12 12
Typical stabilization time s < 1 < 1 < 1 <1
Typical measurement time s < 1.5 < 1.5 < 1.5 < 1.5
Application range (temperature):
With “isoCAL” function +5 to +40 °C +5 to +40 °C +5 to +40 °C +5 to +40 °C
Without “isoCAL” function +15 to +25 °C +15 to +25 °C +15 to +25 °C +10 to +30 °C
Display result

Models MSU6202S- MSU6202P- MSU5202S- MSU4202S-
0CE 0CE 0CE 0CE
Accuracy class* K K k K
Scale interval d* g 0.01 0.01/0.02/0.05 0.01 0.01
Weighing capacity Max* g 6200 1500/3000/6200 5200 4200
Calibration value e* g 0.1 0.1 0.1 0.1
Min. load Min* g 0.5 0.5 1 0.5
Application range according to DIR* g 0.5 – 6200 0.5 – 6200 1 – 5200 05 – 4200
Min. initial weight** g 12 12 10 12
Typical stabilization time s < 1 < 1 < 0.8 < 0.8
Typical measurement time s < 1.5 < 1.5 < 1 <1
Application range (temperature):
With “isoCAL” function +5 to +40 °C +5 to +40 °C +5 to +40 °C +5 to +40 °C
Without “isoCAL” function +10 to +30 °C +10 to +30 °C +10 to +25 °C +10 to +30 °C
Display result
Weighing pan size (W + D) mm 206 + 206 206 + 206 140 + 140 206 + 206

Technical Data
Model-specific Data

Models MSU2202S- MSU1202S- MSU36201S- MSU36201P- MSU20201S-
0CE 0CE 0CE 0CE 0CE
Accuracy class* K K K K K
Scale interval d* mg 10 10 100 100/1000 100
Weighing capacity Max* g 2200 1200 36,200 10,200 /36,200 20,200
Calibration value e* g 0.1 0.1 1 1 1
Min. load Min* g 0.5 0.5 5 5 5
Application range according to DIR* g 0,5 – 2200 0,5 – 1200 5 – 36,200 5 – 36,200 5 – 20,200
Min. initial weight** g 12 12 120 120 120
Typical stabilization time s < 0.8 < 0.8 < 1.5 < 1.5 < 1.5
Typical measurement time s <1 <1 <2 <2 <2
Display result
(depending on the set filter level) 0,1 – 0,4
Protection IP54

Models MSU12201S- MSU8201S- MSU5201S- MSU70200S- MSU36200S-
0CE 0CE 0CE 0CE 0CE
Accuracy class* K K K K K
Scale interval d* mg 100 100 100 1000 1000
Weighing capacity Max* g 12,200 8200 5200 70,200 36,200
Calibration value e* g 1 1 1 10 1
Min. load Min* g 5 5 5 50 50
Tare equalization range (subtractive) < 100%from max. weighing capacity
Application range according to DIR* g 5 – 12,200 5 – 8200 5 – 5200 50 – 70,200 50 – 36,200
Min. initial weight** g 100 100 100 1000 1000
Typical stabilization time s < 0.8 < 0.8 < 0.8 <1 <1
Typical measurement time s <1 <1 <1 < 1.2 < 1.2
Display result
(depending on the set filter level) 0,1 – 0,4
Protection IP54

Balance Dimensions
Balance Dimensions
Microbalances
All dimensions are given in millimeters
max. 88
56
192
358
240
323
d 85 122
d 86.5
d 80
67
121
106.5
35
50 94
70 180 132
246
340

Balance Dimensions
Filter-Microbalances
max. 88
56
192
358
240
323
122
d 106.5
d 84
24
20
106.5
93
77
35
50 94
70 180 132
246
344

Balance Dimensions
High-capacity Microbalances, Models MSU116P, MSU66S, MSU66P, MSU36S, MSU36P

±1
232
154
358
322
435
410
30 MSx36 / MSx66
50 MSx66 / MSA116P
222
181.5 MSx36 / MSx66
240.5 MSA116P
225
56
63
30.5 235.5 55
115
max. 88
56

Balance Dimensions
Semi-microbalances with Motorized Draft Shield


Balance Dimensions
Semi-microbalances and Analytical Balances with Manual DU Draft Shield


Balance Dimensions
Precision Balances with a Readability of 1 mg and Manual DE Draft Shield


Balance Dimensions
Precision Balances with a Readability of 1 mg and Framed DR Draft Shield


Balance Dimensions
Precision Balances with no Draft Shield


Balance Dimensions
Accessories
Cubis® Optional Accessories
Printers and Communication

Verifiable data printer for connection to RS-232, 25-pin accessory interface YDP10-0CE
Verifiable data printer with Bluetooth® data transmission (with YDO01MS-B or IB option only) YDP10BT-0CE
Color ribbon for YDP10-0CE and YDP10BT-OCE 6906918
Paper rolls for printer YDP10-0CE; 5 rolls 50 m each 6906937
Bluetooth® data interface for wireless connection of data printer YDP10BT YDO01MS-B
RS232C data interface, 9-pin including PS/2 for connecting a PC or keyboard YDO01MS-P
RS232C data interface, 25-pin for connection of Cubis® accessories YDO01MS-R
Display cable 3 m for Cubis® MSA and MSU models, for separate setup of display and weighing unit YCC01-MSD3
(Installation by Sartorius Service or in factory [order VF4016])
Cable 3 m between weighing module and electronics module for Cubis® models YCC01-MSM3
with 0.01 mg | 0.001 mg | 0.0001 mg readability
Installation display cable 3 m for Cubis® models, for separate setup of display and weighing unit VF4016
RS232C connection cable to connect PC with 9-pin COM interface, length 1.5 m 7357314
Sartowedge software for data communication between balance and PC YSW02
Sartorius OPC Server for connecting all Sartorius Cubis®
balances
Requires 32-bit Microsoft Windows 2000 or XP with current service packs.
(free download of a 30-day trial version from the Sartorius website)
– Initial license 6289OPC
– Each additional license within an order 6289OPC-L
Displays and Input | Output Elements

MSA control unit with color TFT graphic display and touch screen YAC01MSA
MSE display unit with backlit LC display and tactile keys YAC01MSE
MSU control unit with backlit b | w graphic display and tactile navigation keys YAC01MSU
Barcode reader with connection cable, 120 mm reading range YBR03PS2
Foot switch for printing, taring, or using function keys, selection via menu, incl. T connector YFS01
Infrared sensor for touch-free activation of functions (e.g., draft shield control) YHS01MS
Hand switch for printing, taring, or using function keys, selection via menu, incl. T connector YHS02
Foot switch for the draft shield OPEN | CLOSED functions (only in combination with DA and DI draft shield), YPE01RC
taring and printing
Additional display, LCD, figure size 13 mm, backlit YRD03Z
3-segment control display, red – green – red, for plus | minus measurements, incl. T connector YRD11Z

Balance Dimensions
Pipette Calibration Hardware and Software

Pipette calibration kit (hardware) for models with 0.1 mg and 0.01 mg readability YCP04MS
Consists of moisture trap and all required adapters
Pipette calibration kit (hardware) for microbalance weighing modules 6.6S and 3.6P VF988
Consists of moisture trap and all required adapters
Pipette Tracker pipette calibration software. Software and user manual in English only. YCP04-PT
Pipette Tracker Pro pipette calibration software, for use in regulated areas, networkable and validatable, YCP04-PTPro
according to the 21 CFR Part 11 regulations. Software and user manual in English only.
Documentation basis for validation (IQ, OQ) of Pipette Tracker PRO version. YCP04-VTK
All documents are in English only.
Filter Weighing and Antistatic Accessories

Antistatic weighing pan, diameter 130 mm, for weighing modules with a readability of 0.1 mg or 0.01 mg YWP01MS
Filter weighing pan d 75 mm, for ultramicrobalance or microbalance models VF2562
(weighing modules 6.6S, 2.7S; only together with DF draft shield)
Filter weighing pan d 90 mm, for ultramicrobalance or microbalance models VF2880
(weighing modules 6.6S, 2.7S; only together with DF draft shield)
Ionization blower to eliminate electrostatic charges on sample containers and samples YIB01-DR
Stat-Pen ionization probe for discharging electrostatically charged samples and filters YSTP01
Ionizer with U-shaped electrode incl. power supply for 230 V YIB02-230V
Ionizer with U-shaped electrode incl. power supply for 115 V YIB02-115V
Special Applications
Density determination kit for solids and liquids for weighing modules with a readability < 1 mg YDK01MS
Density determination kit for solids and liquids for weighing modules with a readability of 1 mg YDK02MS
Q-Grip, flexible holder for weigh-in containers and filters up to 120 mm diameter YFH01MS
(replaces the original weighing pan, for Cubis® models with 0.01 and 0.1 mg readability)
Q-Grid grid weighing pan for Cubis® models with a readability of 10 mg or 100 mg for weighing in laboratory hoods, YWP03MS
safety weighing cabinets or workbenches (reduced wind attack surface of the weighing pan; replaces the standard
weighing pan)
Weighing Tables
Weighing table made from synthetic stone, with vibration dampening YWT03
Wall console YWT04
Weighing table made from wood with synthetic stone for precise, reliable measurements YWT09
Weighing Accessories
Weighing scoop made from chrome nickel steel , 90 + 32 × 8 mm 641214
Aluminum weighing scoop, 4.5 mg (250 pieces) for ultramicrobalance and microbalance models 6565-250
Aluminum weighing scoop, 52 mg (50 pieces) for ultramicrobalance and microbalance models 6566-50
Support arm for 10/100 mg precision weighing modules for raising the control units MSE, MSU, MSA YDH01MS
Stand for precision weighing modules with a 100 mg | 1 g readability and weighing capacity > 20 kg for raising the YDH02MS
control units
Hook for below-balance weighing for precision weighing modules with a 100 mg | 1 g readability and weighing capacity 69EA0040
> 20 kg (not for models verified for legal use, CE marks)
Adjustable sample holder for high-capacity Cubis® microbalances MSU36x, MSU66x and MSU116P YSH02
Slotted weighing pan for MSU116P with a 90 mm diameter YWP10
Slotted weighing pan for high-capacity microbalances (MSU36, MSU66 and MSU116P), diameter 50 mm YWP09
The brand name and logo for Bluetooth® wireless technology are are the property of Bluetooth SIG Inc. The use of this brand name
and trademark by Sartorius is under license. Other brand names and trademarks are the property of their respective owners.

Declarations of Conformity
Weighing instruments for use in legal metrology: Council Directive 2014/31/EU
“Non-automatic Weighing Instruments”
This Directive regulates the determination of mass in legal metrology.
For the respective Declaration of Conformity for weighing instruments Sartorius has
performed the conformity assessment for use as legal measuring instruments and
that have an EC Type-Approval Certificate, declaration attached the instrument.
This Directive also regulates conformity assessment by the manufacturer,

provided that an EC Type Approval Certificate has been issued and the
manufacturer has been accredited by a Body registered at the Commission of the
European Community for performing such conformity assessment.
The legal basis for Sartorius to perform the conformity assessment is EC Directive
No. 2014/31/EU for non-automatic weighing instruments. The further legal basis
is founded on the Sartorius Quality Management System issued by the Metrol-
ogy Department of the Regional-Administration Office of Lower Saxony, Germany
(“Mess- und Eichwesen Niedersachsen”).
“Installation” Service in Germany

Our “Installation” service package provides a range of important services that
guarantee satisfactory work from your balance:
– Setup
– Getting Started
– Inspection
– Training
If the installation of the weighing instrument is to be carried out by Sartorius,

please request this service from a customer service employee.
Periodic Verification in Germany

Balance verification for legal metrology is valid until the end of the calendar year
after next.
If the balance is used for fill level control in accordance with legislation on
prepackaging, conformity assessment is valid until the end of the following
calendar year. Periodical verification must currently be carried out by a weights and
measures official. Periodical verification should be requested in good time from
the local Weights and Measures office. As appropriate, please observe all statutory
amendments.
Periodic Verification within Europe and Outside of Germany

The expiration date of the conformity assessment/verification depends on the
national regulations of the country in which the weighing instrument is used.
For information on verification and legal regulations currently applicable in your
country, and to obtain the names of the persons to contact, please contact your
local Sartorius office, dealer, or Service Center.

For verified balances, the conformity declaration supplied with the balance is valid for use in the EEA.
Please retain this declaration.

EC Type-examination Certificate

EU Type-approval Certificate

Plates and Markings

Plates and Markings

Plates and Markings

Plates and Markings

Plates and Markings

Plates and Markings

Sartorius Lab Instruments GmbH & Co. KG
Otto-Brenner-Strasse 20
37079 Goettingen, Germany
Phone: +49.551.308.0
www.sartorius.com
The information and figures contained in these

instructions correspond to the version date
specified below.
Sartorius reserves the right to make changes
to the technology, features, specifications and
design of the equipment without notice.
Masculine or feminine forms are used to
facilitate legibility in these instructions and
always simultaneously denote the other
gender as well.
Copyright notice:
This instruction manual, including all of its
components, is protected by copyright.
Any use beyond the limits of the copyright law
is not permitted without our approval.
This applies in particular to reprinting,
translation and editing irrespective of the type
of media used.
© Sartorius Germany
Last updated:
11 | 2017
Printed in the EU on paper bleached

without chlorine. | W
Publication No.: WMS6006-e171105

Sartorius Cubis Series: User Manual

Uploaded by

Copyright:

Available Formats

Sartorius Cubis Series: User Manual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Sartorius Cubis Series: User Manual

Uploaded by

Copyright:

Available Formats

User Manual

Sartorius Cubis® Series

2 Cubis® MSU User Manual

Notes on Using this Manual

Symbols and Signs

2 Warning symbol for various types of dangers.

h This symbol indicates useful information and tips.

H This symbol means that the USER key should be pressed.

D This symbol means that the TASK key should be pressed.

When individual functions are displayed, press the associated softkey.

t Indicates a required action

y Describes the result of an action

1. If a procedure has multiple steps...

2. ... the steps are numbered consecutively.

– Indicates an item in a list

Cubis® MSU User Manual 3

Danger of Electrical Shock!

4 Cubis® MSU User Manual

Note on cable quality:

Hazards at the Place of Installation and During Operation

3 Avoid generating static electricity and establish equipotential bonding.

3 Exercise caution to avoid glass breakage.

3 Models with a separate electronics module (e. g. MSU6.6/3.6/2.7), MSU225S/P

3 Exercise caution to avoid squeezing or crushing fingers when

Cubis® MSU User Manual 5

General View of the Equipment and Equipment Supplied

Item Description Item Description

1 Weighing pan 12 Female connector for weigh cell

6 Cubis® MSU User Manual

Models MSU66S, MSU66P, MSU36S, MSU36P

Item Description Item Description

1 Push handle/Handle 10 DC jack

Cubis® MSU User Manual 7

Item Description Item Description

1 Push handle/Handle 10 DC jack

8 Cubis® MSU User Manual

4 Analytical and precision balances with a weighing range of up to 15 kg

6 1 Upper sliding draft shield panel/handle

Cubis® MSU User Manual 9

General View of the Equipment and Equipment Supplied

Item Description Item Description

1 DC jack 5 USB socket for a PC connection

10 Cubis® MSU User Manual

Models MSU116P, MSU66S, MSU66P, MSU36S, MSU36P:

t Loosen and remove the strap.

t Remove the cardboard sleeve.

Cubis® MSU User Manual 11

t Remove the retainer securing the front draft shield panel.

t Open the plastic wrapping.

Exercise caution to avoid glass breakage.

12 Cubis® MSU User Manual

t Place the device at the intended installation location.

t Open the draft shield doors.

t Remove the inner foam padding from the draft shield.

Balance with the Analytical Draft Shield

t Open the packaging at the top.

Cubis® MSU User Manual 13

t Place the packaging with the balance on the floor.

t Remove the top part of the packaging.