Dry Cast Concrete

Top 10 Facts about Dry-Cast Concrete
National Precast Concrete Association / Precast Magazines / Precast Inc. Magazine / 2015 - September-
October / Top 10 Facts about Dry-Cast Concrete / Top 10 Facts about Dry-Cast Concrete
September 10, 2015 7 Comments
A dry-cast mix design allows Concrete Systems Inc. production staff to

manufacture concrete barriers at a high-pace. (NPCA file photo)
By Eric Carleton, P.E.

Concrete is one of the oldest and most widely used building materials in the
world. Some of the earliest concrete structures were built by tradesmen in the
Middle East more than 8,000 years ago. When constructing the underground
concrete water cisterns, they had already learned that the key secret of quality
concrete is to keep the water-cement ratio as low as possible. Today, precast
manufacturers continue to rely on this secret to produce quality concrete. One
such product that depends on a low w/c ratio is dry-cast concrete. A dry-cast
mixture has just enough water to initiate cement hydration within the range of
0.30 to 0.38 without the use of admixtures. Below, several important facts
regarding dry-cast concrete are outlined.
1. Increased production
One benefit of using dry cast is it can be consolidated within a form. The stiffness
of the mix allows the form to be immediately stripped. The product will stand
under its own weight to complete the curing process and the form can be
returned to cast another product.
2. Reduced shrinkage and creep, rapid strength increase
In 1969, The Aberdeen Group published an article titled, “An Introduction to Dry-
cast Concrete,” that introduced the process. All the concrete components are
placed into the formwork dry, then compacted and lastly, infused water is added
into the mix via capillary action to start hydration. Though this process of dry
casting didn’t catch on commercially, the article described the reasons for the
positive attributes of dry-cast concrete: “Both shrinkage and creep are reduced
because all of the aggregate particles are in contact with each other, instead of
being separated by the cement-water paste formed in the wet-mix process of
producing concrete. The already compacted aggregate particles must of necessity
resist the shrinkage of the cement, with the result that the particles are
preloaded to increase the compressive strength of the concrete.”
Modern dry-cast concrete processes introduce water during mixing prior to

vibration. The low amount of water and corresponding paste combined with
consolidation from external vibration provides the same reduced separation of
aggregates. Consequently, the same attributes described include a rapid increase
in compressive strength. In some cases, dry-cast products can comply with
specified material strength requirements in 24 hours.
3. Dry-cast concrete ≈ roller-compacting concrete

Although dry-cast concrete mix designs and applications have been used for
decades within the precast concrete industry, the batching method is rarely
discussed in concrete engineering classes. In fact, zero-slump concrete testing is
not included in ACI Level 1 technician certification. With the expanded use of
roller-compacted concrete for paved surfaces, dry-cast methods are now
becoming more popular with engineers. Many of the same attributes associated
with dry-cast concrete are present with RCC.
4. Vibration: not one size fits all
One of the primary keys to quality dry-cast concrete products is consolidating

the mix with intensive external vibration, because the stiffness of the mix makes
traditional internal vibration impossible. Dry-cast products need to be
consolidated through a variety of methods. One is the use of centrifugal force and
mechanically packing the mix into the outside form jacket with the use of
spinning cylindrical heads. The method is similar to the packer-head pipe-
making process. The other more conventional methods are via individual
external vibrators attached to the product form or the entire form attached to a
vibrating table. Both vibration processes are designed to consolidate the mix to
the maximum density.
For optimal use, precast concrete producers need to be aware that the energy
provided by vibration technology needs to be directed to the concrete mix.
Additionally, different products may require different vibration settings to insure
the consolidation energy is adequate for the product being cast. For example, a
small short inlet section may use a vibration with high frequency but low
amplitude, while a large 8-foot-tall manhole section may need a higher amplitude
setting and lower frequency to evenly distribute the energy throughout the
product mass.
5. A heavy-duty form, all day long
The need for heavy-duty forms is twofold. Due to the need to transfer intense
external vibration energy to the mixture through the formwork, dry-cast forms
need to be very rigid. This does not simply mean thicker skin, as increased jacket
thickness can lead to dampening as a result of vibration energy. Similarly, simply
adding structural steel stiffeners can also be detrimental. Adding more weight to
a form reduces the effectiveness of the vibration methods employed.
Heavy-duty forms are typically used continuously throughout the day’s

production. The primary benefit of using a dry-cast process is the ability to
produce multiple precast concrete sections using a singleform system.
Consequently, that single form is handled repeatedly throughout the day with
setup, pouring, vibration, transportation to curing and setup areas and product
stripping. A dry-cast form must be designed to handle all that use, yet not be so
bulky to reduce the consolidation effectiveness. Proper form design is an
engineering art optimizing the highest form stiffness and ruggedness with the
lowest form weight.
6. Let a little out at the bottom
It is not always recognized or understood that most dry-cast products’ wall

surfaces are not perfectly vertical. A slight taper of the product is required to
accommodate immediate stripping. For traditional wet-cast precast operations,
the concrete mix is cast and internally vibrated into the forms and cured
overnight. The product is then hardened when the forms are removed.
Typically, to assist with stripping, the forms are hinged on the outside with
latches to open and are collapsible on the inside. However, many dry-cast outside
jackets or inside cores are fabricated as a single-steel section. Consequently, to
physically pull out either the form from the cast product or the cast product from
an anchored core or jacket, the form must include a slight taper. This reduces the
continuous skin friction of the lift and the potential vacuum suction that would
occur with vertical-facing forms. This taper is typically only 1/8 to 1/4 inch over
the length of the wall and has minimal effect on product function. However, this
small variation should be noted if the exact product perimeter or circumference
is needed.
A heavy-duty form is needed to manufacture dry-cast precast concrete
products. (NPCA file photo)
7. Leave the slump cone in the closet
When speaking to a precast manufacturing friend who lives in the Chicagoland

area on this subject of dry-cast facts, he said, “Unlike the Cubs, dry-cast concrete
doesn’t slump.”
Dry cast is known as zero-slump or negative-slump concrete because with typical

mix designs, additional water could be added and the slump would still be zero if
tested in accordance to ASTM C143, “Standard Test Method for Slump of
Hydraulic-Cement Concrete.” In fact, the mix is so stiff that the tamping rod
simply would leave a hole when extracted.
A true story regarding slump testing and dry-cast concrete occurred at a

concrete pipe plant in the Midwest. During an unannounced inspection by the
owner’s engineer, a slump test was requested. When the plant manager said they
did not have a slump cone, the engineer lambasted him about the company being
inept by not conducting daily slump testing. After accepting a little more abuse,
the plant manager answered while pointing at the 2 full kilns of 24-inch-
diameter-by-8-feet-tall sections of pipe made that day, “Look, I just did 300
slump tests today, if the mix is off, they all fall down!” The engineer learned
something new about dry-cast concrete that day.
8. Leave the air tester
It is extremely difficult, if not impossible, to use air entrainment admixtures to

produce a controlled air content of a finished dry-cast product. It is believed the
high-intensity vibration and consolidation of the mix collapses the entrained air
bubbles. However, precast concrete products that use dry-cast processes have
shown complete resilience to freeze-thaw degradation, which can occur with
mixes of higher w/c ratios. Thousands of precast concrete pipes and box culverts
project out of roadway embankments in highways and are exposed to severe
freeze-thaw environments, yet they hold up to abuse. Canadian testing company,
Service d ’Expertise en Materiaux Inc. confirmed this through formal research.
The study conducted an extensive literature review that showed properly made
dry-cast concrete resisted frost-induced cracking. Additionally, dry-cast pipe and
box culvert products proved to meet the requirements of ASTM C1262-97,
“Standard Test Method for Freeze-Thaw Durability of Manufactured Concrete
Masonry Units and Related Products.”
9. Running on all cylinders
Though dry cast is not conducive to testing for slump or air, a producer still
needs to make and test concrete cylinders for testing in accordance to the
product specification. However, the method of fabrication for these cylinders
varies greatly from the traditional wet-cast concrete mix means to make a test
cylinder described in ASTM C33, “Standard Practice for Making and Curing
Concrete Test Specimens in the Field.” It is important to know these differences.
More information can be found in the July-Aug. 2014 Precast Inc. article
“Compress for Success.”
10. Production Savings & Speed of Fabrication
If the market for the precast product is great and the product to be made can be
standardized, then the initial expense of the dry-cast forms and production
equipment can be justified. As described by Mark Wilson, plant manager at
Cretex Concrete Products, “The economic factor (of dry-cast production) can’t be
ignored. Man-hours per ton and form costs over time can be attractive, as well as,
a quick response time in serving the customer.”
Quality required
As discussed, dry-cast mix and production methods provide many advantages.

New admixture technology has also introduced game-changing properties to
wet-cast concrete, including the rapid application of self-consolidating concrete
within the precast industry. However, regardless of your production methods,
always make sure it is quality concrete.
Eric Carleton, P.E., is NPCA’s vice president of Technical Services.
Filed Under: Precast Inc. Magazine, 2015 - September-October, Top 10 Facts about Dry-Cast
Concrete, Precast MagazinesTagged With: aggregate, dry-cast, form, mix design, vibration

Dry Cast Concrete

Uploaded by

Copyright:

Available Formats

Dry Cast Concrete

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Dry Cast Concrete

Uploaded by

Copyright:

Available Formats

What are the benefits of using dry-cast concrete?

What are the benefits of using dry-cast concrete?

What are some differences between dry-cast concrete and wet-cast concrete?

What are some differences between dry-cast concrete and wet-cast concrete?

Top 10 Facts about Dry-Cast Concrete

September 10, 2015 7 Comments

A dry-cast mix design allows Concrete Systems Inc. production staff to

By Eric Carleton, P.E.

2. Reduced shrinkage and creep, rapid strength increase

Modern dry-cast concrete processes introduce water during mixing prior to

3. Dry-cast concrete ≈ roller-compacting concrete

4. Vibration: not one size fits all

One of the primary keys to quality dry-cast concrete products is consolidating

5. A heavy-duty form, all day long

Heavy-duty forms are typically used continuously throughout the day’s

6. Let a little out at the bottom

It is not always recognized or understood that most dry-cast products’ wall

7. Leave the slump cone in the closet

When speaking to a precast manufacturing friend who lives in the Chicagoland

Dry cast is known as zero-slump or negative-slump concrete because with typical

A true story regarding slump testing and dry-cast concrete occurred at a

8. Leave the air tester

It is extremely difficult, if not impossible, to use air entrainment admixtures to

9. Running on all cylinders

As discussed, dry-cast mix and production methods provide many advantages.

Eric Carleton, P.E., is NPCA’s vice president of Technical Services.

You might also like