Bridge ONT Quick Start 07
Bridge ONT Quick Start 07
Quick Start
Safety Information
Before using the device, read these precautions carefully. Follow these precautions and instructions
to ensure optimal product performance and to avoid danger and legal or regulatory violations.
Fire-proof Precautions
Keep the device away from fire or heat sources, including electric heaters, ovens, stoves, and
candles. Otherwise, the shell of the device may become hot or melt, causing fire in extreme
cases.
Replace deteriorated cables or power socket components on the power supply line or near the
device in a timely manner to eliminate safety risks.
Potentially Explosive Area
Do not place or operate the device in an environment with that contains flammable or explosive
gas or smoke.
Do not place flammable or explosive materials below or above the meter cabinet.
General Safety Precautions
Do not lead the strength member of the optical fiber or other metal parts indoors. Do not install
telephone lines, network cables, power adapters or power adapter cables outdoors. These
measures will help to prevent damage to the device and injury to people, which are especially
possible during thunderstorms.
If the power adapter is damaged from human factors, and the inside circuit is exposed, do not
touch the exposed parts. Otherwise, security risks are present.
Keep the device out of the reach of children. Components and accessories are small and could
pose a choking risk.
Looking directly at the optical port may injure your eyes.
Do not use any power adapters that are not in the standard configuration. Otherwise, the device
may be abnormal or unsafe.
If a backup power unit (BBU) is available in the packing box, do not disassemble it, refit it, or
put it in a fire. Otherwise, it may create a safety risk.
Product Overview
Product Function
� 1 Ethernet port
HG8110 series
� 1 POTS port
� 1 Ethernet port
HG8012 series
� 1 CATV port
� 2 Ethernet ports
HG8120 series
� 1 POTS port
� 4 Ethernet ports
HG8242 series � 2 POTS ports
� 1 CATV port
� 4 Ethernet ports
HG8240 series
� 2 POTS ports
NOTE
If some device types are not in the preceding list, refer to http://www.huawei.com.
2
Technical Specifications
Power adapter input: 100–240 V AC, 50/60 Hz
System power supply: See the nameplate on the device.
Ambient temperature: 0ºC to +40ºC
Ambient humidity: 5%–95% (non-condensing)
For other technical specifications, see the following table.
NOTE
If the appearance of the product in this document differs from the actual product, the actual product
prevails.
3
Mounting a GPON Terminal On The Desk
The schematic diagram for placing the device on a desk horizontally is as
follows (The HG8240H5 is used as an example here.):
1 2 3 4
2 3 mm
1
Reset
WLAN
WPS
4
NOTE
This terminal is mainly placed horizontally on a desk. When it is mounted
onto a wall, the silkscreen of its indicator is reversed. If you have a special
requirement on the silkscreen, purchase another terminal.
Connecting Cables
This document uses the HG8240H5 as an example to describe the connections. Ports
on GPON terminals of other types may be different. Therefore, connect cables based
on the ports that are actually supported by the device. If the external device is different
from the device in the figure, refer to the description for connections of the external
device.
1 2 3 4
1 Power switch
2 Power port
3 POTS port
4 Ethernet port
IP STB
5 Optical port
Power socket PC
Fax machine Phone TV set
6 Reset
5
Step 1 Use an optical fiber to connect the optical port on the ONT and the
optical port on the wall.
• The optical port of the HG8242 series, HG8240 series and HG8040
series are at the back of the device. For how to connect the optical
port, see the following figure (The HG8240H5 is used as an example
here.):
• For how to connect the optical ports of other ONTs, see the following
figure:(Use an optical fiber to directly connect the OPTICAL port on
the ONT to the optical port on the wall.) The HG8110F is used as an
example here.
6
NOTE
1.The optical connector connected to the OPTICAL port is an SC/APC connector, and
the type of the optical connector connected to the optical port in the wall is determined by
practical conditions.
2.To ensure normal use of fibers, make sure that the fiber bend radius is larger than
30 mm.
Step 2 Use a network cable to connect the LAN port to a PC or the Ethernet port on
the IP STB.
Step 3 Use a phone line to connect the TEL port to a phone or fax machine.
Step 4 Use a power adapter to connect the POWER port to the power socket.
NOTE
The preceding figure connects the power adapter as an example. For details about how to
use the backup battery unit, see the usage guide to the backup battery.
Step 5 Press the ON/OFF power switch.
Step 1 Set the IP address of the PC in the same subnet as the management IP address
of the GPON terminal.
NOTE
You can find the default management IP address on the nameplate of the
device.
Step 2 Enter the management IP address of the GPON terminal in the address bar of
Internet Explorer and press Enter.
The login window is displayed.
Step 3 In the login window, select your preferred language, enter the user name and
password ( printed on the nameplate of the device.), and click Login. After the
password is authenticated, the Web configuration window is displayed.
NOTE
-Shipped from different manufacture batches, the nameplates of some devices do not have
the IP address, user name, and password printed. In such a case, log in to the device using
192.168.100.1 (or 192.168.1.1), root (user name), and adminHW (password).
- If you do not perform any operations after logging in to the system for five minutes, you will
exit the system and the system automatically returns to the login interface.
- The system will be locked if you input incorrect user name and password three consecutive
times. One minute later, it will be unlocked.
- Change the initial password after logging in to the web page.
7
Indicator Description
Table 1 Indicator status description 1
Indicator Status Description
The CATV function is enabled and CATV signals
Steady on
are received.
CATV
The CATV function is disabled or CATV signals
Off
are not received.
The ONT is registered with the softswitch but no
Steady on
service flows are transmitted.
TEL1–TEL2 Blinking Service flows are transmitted.
The ONT is not powered on or fails to be
Off
registered to the softswitch.
Steady on The Ethernet connection is in the normal state.
LAN1–LAN4 Blinking Data is being transmitted on the Ethernet port.
Off The Ethernet connection is not set up.
LOS/PON See Table 2.
Steady green The terminal is powered on.
POWER
Off The power supply is cut off.
8
Disposal and recycling information
The crossed-out wheeled-bin symbol on your product, literature or packaging reminds
you that all electronic products must be taken to separate waste collection points at the
end of their working lives; they must not be disposed of in the normal waste stream with
household garbage. It is the responsibility of the user to dispose of the equipment using
a designated collection point or service for separate recycling of waste electrical and
electronic equipment (WEEE) according to local laws.
Proper collection and recycling of your equipment helps ensure electrical and electronic equipment
(EEE) waste is recycled in a manner that conserves valuable materials and protects human health
and the environment, improper handling, accidental breakage, damage, and/or improper recycling at
the end of its life may be harmful for health and environment. For more information about where and
how to drop off your EEE waste, please contact your local authorities, retailer or household waste
disposal service.
Disposal of the device is subject to WEEE Directive Recast (Directive 2012/19/EU). The purpose of
separating WEEE from other waste is to minimize the potential environmental impacts and human
health risk of any hazardous substances that may be present.
9
FAQs
10
Warranty Card
Thank you for choosing Huawei Technologies Co., Ltd. To get better services,
please read this warranty card carefully, fill in the required information, and
preserve this card in good condition.
User Information
Personal or
company's full name:__________________________________________________
Address/Postal Code:_________________________________________________
Telephone:__________________________________________________________
Email:______________________________________________________________
Product Type:________________________________________________________
Product Serial Number:________________________________________________
Purchase Date:______________________________________________________
Invoice Number:______________________________________________________
Dealer's Name:______________________________________________________
Dealer's Address:_____________________________________________________
Dealer's Telephone:___________________________________________________
Special Notice:
1. The warranty card shall be applicable only after being stamped by the dealer.
2. The warranty card must be preserved in good condition and free of any scratch or
alteration.
3. To claim such service for defects that are not included in the following exclusion
terms, the warranty card and the invoice that records that product serial number
shall be presented to a Huawei authorized service partner.
Exclusions:
In any of the following cases, the warranty card becomes unenforceable or
inapplicable without prior notice:
1. The defects are caused by improper handling in transportation and assembly.
2. The defects are caused by the fact that the product is dismantled or altered by
anyone that is not from a Huawei authorized service partner.
3. The defects are caused by the fact that the product is used in a harsh environment
that is not suitable for the operation of the product.
4. The defects are caused by any force majeure including but not limited to fire,
earthquake, lightning, and tsunami.
5. The defects are caused by the fact that the product is used or handled incorrectly,
roughly or not as instructed in the applicable User Guide.
6. The normal wear and tear, including but not limited to the normal wear and tear of
the shell and the power module, shall not be covered by the limited warranty.
7. The warranty card is altered or illegible, or the product serial number recorded on
the warranty card is inconsistent with the actual one imprinted or labeled on the
product.
In any case that is not covered by this limited warranty or should the warranty expire,
Huawei shall charge for the service(s) claimed for the products if the product is still
remediable. Huawei reserves all rights to interpret this limited warranty.
PASS
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of
their respective holders.
Notice
The information in this document is subject to change without notice. Unless
otherwise stated, this guide serves only as a guide. All statements, information, and
recommendations in this document do not constitute a warranty of any kind, expressed
or implied.
Issue: 07
BOM number: 31505717