FADHILI ONSHORE & OFFSHORE UPSTREAM FACILITIES

DIVISION
6600035803 (OOK) /CRPO NO.6510781900 / BI No. 10-01902
HASBAH OFFSHORE GAS FACILITIES INCREMENT II

ARAMCO DUMMY PO NO. FGCI-M98-89-A039-DA

PO NO. HYDR/78000-09836/JRD

PO ITEM NO/ TAG NO. 4-5-6-7-8-9-18-23-32-33-34-36-41-42-43

HSBH-40/43, HSBH-44/47, HSBH-48/51, HSBH-52/55, HSBH-56/59,
PLATFORM NO.
HSBH-60/63
DOCUMENT TYPE DRAWING

NMR SUB-ITEM NO. 601.1

DOCUMENT TITLE GENERAL ASSEMBLY DWG 1.13/16”- 16_351_001

CONTRACTOR DOCUMENT NO. PERACT-PI-Q23-DW-0004

VENDOR DOCUMENT NO. GA DWG 16_351_001

D 06/06/2017 M.Raschetti F.Tamola A.Barberini

Issued for Approval Michel
Firma digitale di
Michel Raschetti Fulvio Firma digitale di
Fulvio Tamola Alessandro
Barberini
Firma digitale di
Alessandro Barberini

Raschetti Data: 2017.06.06

16:18:54 +0200 Tamola Data: 2017.06.06
16:19:02 +0200
Data: 2017.06.06
16:19:09 +0200

C 05/09/2017 M.Raschetti F.Tamola A.Barberini

Issued for Approval
B 03/17/2017 M.Raschetti F.Tamola A.Barberini
Issued for Approval
A 01/23/2017 Issued for Approval D.Saligari F.Tamola A.Barberini

Rev. Date Description Prepared By Checked by Approved by

Project documents are controlled documents.
Revisions are denoted in the right-hand SAOC BI No: 10-01902
margin.

DISCIPLINE CHECK RETURN TO VENDOR Reviewed By

Engineer
A. Approved. Fabrication may proceed

QA Department B. Approved with comments. Vendor to revise the

document and resubmit for approval. Fabrication may
proceed.

C. Not Approved.

Other
D. For Information Only
Date:
LEGEND: Customer: CONSORTIUM OF L&T HYDROCARBON ENGINEERING & EMAS AMC
= INCONEL 625 OVERLAY DETAIL D DETAIL A Project: HASBAH OFFSHORE GAS FACILITIES INCREMENT II
16a End User: SAUDI ARAMCO ORGANISATION
39b
09a PERAR Ref.: 16-351
DETAIL C 06 09 16b Customer Item: 4-5-6-7-8-9-18-23-32-33-34-36-41-42-43
16b
39a 70
3
27c
45
47b
99a
16
77e PIN DETAIL
77d 31
99

25a 77
32
47 43
24a

30
77a 07
10

08
27d A
D
601.1
3

D 06/06/2017 ISSUED FOR APPROVAL M.R. F.T. A.B.

B C 05/09/2017 ISSUED FOR APPROVAL M.R. F.T. A.B.
Minimum groove hardness: 210 HBW B 03/17/2017 ISSUED FOR APPROVAL M.R. F.T. A.B.
A 01/23/2017 ISSUED FOR APPROVAL D.S. F.T. A.B.
DESCRIPTION

05d

16-351 CD-16-0351-X-00CS D
27a

16-351
24 FGCI-M98-89-A039-DA A 01/23/2017
C B 03/17/2017
PI-Q23-MR-4045 C 05/09/2017
01 D 06/06/2017
NTS

25
48 29

DETAIL B 39l 34l REV.NO.

D
DATE

06/06/2017
REVISION DESCRIPTION

ISSUED FOR APPROVAL

34 This document contains Perar Spa proprietary
and confidential informations. It is loaned for
Tollerances, unless
otherwise stated
TM
limited purposes only. It may not be
Greater of To ±
reproduced in whole or part or disclosed to third
parties without the prior written consent of 0 75 0.1 TITLE
Perar Spa. The document is to be returned to

86
Perar Spa upon request and in all events upon
completion of the use for which it was loaned.
75
200
200
500
0.3
0.5 SIDE ENTRY BALL VALVE
500 Over 1.5 SUBJECT
A3
Scale Size Angle ± ½°
GENERAL ASSEMBLY DRAWING General Outline Drawings
Sheet 1/4
Surface finish to be 3 Ra
Remove all burrs and sharp edges SIZE CLASS Weight D
REVISIONS 1 13/16" API 10000 On-Off Valves With Actuators, 10000 PSI
Drawing by Verified by Approved by
Mod. Description Date Dwg. Ver. Appr. Digital
Hasbah-II Wellheads Facilities
Firma digitale di Firma digitale di Firma digitale di

Signature Doriano Doriano Saligari

Data:
Fulvio Fulvio Tamola
Data:
Alessandro Alessandro
Barberini
Saligari Barberini
1 Revision according to Customers Comment's 17/03/17 Raschetti Tamola Barberini 2017.06.06
16:19:25 +0200 Tamola 2017.06.06
16:19:34 +0200
Data: 2017.06.06
16:19:43 +0200

Drawing by Verified by Approved by

05 53 33 03 04 2 Revision according to Customers Comment's 09/05/17 Raschetti Tamola Barberini
Date

23/01/17 Saligari Tamola Barberini

HASBAH SAUDI ARABIA

3 Revision according to Customers Comment's 06/06/17 Raschetti Tamola Barberini

DWG N°

CD-16-0351-X-00CS REV3 G09 L PERACT-PI-Q23-DW-0004 1 D

 POS Q.TY PART NAME MATERIAL NOTE GENERAL NOTES:
(1) Piping Spec: 95LL0T02
01 1 BODY ASTM A694 F60 (ISO 10423, 60K) (1)
(2) Valve & Seals Qualified as per ISO 10423 PR2.
03 2 SEAT API6A718 (2) (3) Valve in accordance with ISO 10423,04-SAMSS-055 (17 Jul 2014);04-SAMSS-056 (01 Sep 2015); 04-SAMSS-049
04 1 BALL API6A718 (2) (8 Mar 2016); 04-SAMSS-058 (1 Sep 2015); 02-SAMSS-012 (10 Sep 2013) ;04-SAMSS-035 (11 Sep 2013); 34-SAMSS-717 (1 jan 2012);
05 16 SEAT SPRING ELGILOY 34-SAMSS-718 (12 feb 2015); 04-SAMSS-003(11 Oct 2010); CE-892161 .
05d 1 STEM SPRING ELGILOY (4) Valve as per API 6FA fire safe certified & tested.
06 1 STEM API6A718 (5) Self Relieving seats, SPE-Single Piston Effect, DBB & Bi-Directional.
07 1 THRUST WASHER UNS N06625+PTFE (6) Valve design for 10 000 PSI at 143.3°C.
08 1 CLOSURE ASTM A694 F60 (ISO 10423, 60K) (1) (7) Drain Location as per MSS SP 45.
09 1 LIP SEAL PTFE+ELGILOY (8) ISO 10423 Material Class HH-400. 3
09a 1 GASKET GRAPHITE (9) Temperature range: -45° / 143.3° C.
10 4 CAP SCREW ASTM A320 L7M (10) Valve as per ISO 10423 PSL-3 & Gas test as per PSL-4 requirements.
16 1 V-PACK (2 RINGS) PTFE+ELGILOY+PEEK (11) Marking as per ISO 10423 & API 6FA & MSS SP 25.
16a 1 GASKET GRAPHITE (12) Actuator Operating Mounting Adapter flange: ISO 5211-F16.
16b 2 STEM GASKET PTFE (13) All wetted surfaces,parts,surface treatments, weld and heat-affected zones of welds exposed to line fluids, Including
materials under overlays, as per NACE MR0175/ISO 15156:2009.
24 7 STUD BOLT ASTM A320 L7M
(14) Vent/Drain connection: ISO 10423 Figure 19 Type II - 9/16'', AE STYLE 15000 PSI
25 7 NUT ASTM A194 7M
(15) Valve FEA as per ASME Sec. VIII Div.2, (Ed.2013)
24a 4 STUD BOLT ASTM A320 L7M
(16) Valve 9COM 6000014982
25a 4 NUT ASTM A194 7M (17) For Overall dimensions see DWG: PERACT-PI-Q23-DW-0005 (Perar CD-16-0351-X-00LY_ ) / PERACT-PI-Q23-DW-0032 (CD-16-0351-X-01LY_)
27a 1 BEARING UNS N06625+PTFE PERACT-PI-Q23-DW-0084 (Perar CD-16-0351-X-08LY_) / PERACT-PI-Q23-DW-0092 (Perar CD-16-0351-X-11LY_)
27c 1 BEARING UNS N06625+PTFE (18) For Name Plate & Tag Plate see DWG: PERACT-PI-Q23-DW-0007 (Perar CD-16-0351-X-00SH_)
27d 1 BEARING UNS N06625+PTFE (19) External Coating as mentioned below
29 1 TRUNNION INCONEL 718 (ISO 10423,60K) a) Carbon steel/Alloy Steel Material as per APCS-1A
30 1 GLAND INCONEL 718 (ISO 10423,60K) b) Stainless Steel as per APCS-1B
31 1 GASKET GRAPHITE
32 1 LIP SEAL PTFE+ELGILOY VALVE DATASHEET NUMBER ISS DOCUMENT NUMBER VALVE TAG PIPING SPEC
601.1
3
33 2 LIP SEAL PTFE+ELGILOY CE-881867 CE-880411 G09-H40-ZV-1012
D 06/06/2017 ISSUED FOR APPROVAL M.R. F.T. A.B.
CE-881868 CE-880412 G09-H40-ZV-1032 C 05/09/2017 ISSUED FOR APPROVAL M.R. F.T. A.B.
34 1 PLUG INCONEL 625 CE-881173 CE-881095 G09-H40-ZV-1052 B 03/17/2017 ISSUED FOR APPROVAL M.R. F.T. A.B.
3 A 01/23/2017 ISSUED FOR APPROVAL D.S. F.T. A.B.
34l 1 STOP PLATE CAP-SCREW ASTM A320 L7M CE-881870 CE-880414 G09-H40-ZV-1148 DESCRIPTION

39a 4 CAP SCREW ASTM A320 L7M CE-832924 CE-831439 G09-H44-ZV-1012

39b 4 CAP SCREW ASTM A320 L7M CE-832925 CE-831440 G09-H44-ZV-1032
CE-832926 CE-831441 G09-H44-ZV-1052
39l 1 STOP PLATE AISI 316 CE-832928 CE-831443 G09-H44-ZV-1148
43 1 STEM GREASE FITTING INCONEL 625 CE-884252 CE-882767 G09-H48-ZV-1012 16-351 CD-16-0351-X-00CS D
43a 1 CHECK VALVE INCONEL 625 CE-884253 CE-882768 G09-H48-ZV-1032
45 1 LANTERN INCONEL 625 CE-884254 CE-882769 G09-H48-ZV-1052
CE-884256 CE-882771 G09-H48-ZV-1148 95LL0T02
47 1 GASKET GRAPHITE CE-886555 CE-885099 G09-H52-ZV-1012
16-351
A 01/23/2017
47b 1 LIP SEAL PTFE+ELGILOY FGCI-M98-89-A039-DA
CE-886556 CE-885100 G09-H52-ZV-1032 B 03/17/2017
PI-Q23-MR-4045 C 05/09/2017
48 8 CAP SCREW ASTM A320 L7M CE-886558 CE-885102 G09-H52-ZV-1148 D 06/06/2017
53 2 SPRING HOLDER INCONEL 625 CE-888931 CE-887446 G09-H56-ZV-1012
NTS
CE-888932 CE-887447 G09-H56-ZV-1032
70 1 KEY ASTM A182 F55 CE-888933 CE-887448 G09-H56-ZV-1052
77 2 PIN ASTM A29 Gr G4130 CE-888935 CE-887450 G09-H56-ZV-1148
77a 2 PIN ASTM A29 Gr G4130 CE-891269 CE-889783 G09-H60-ZV-1012
77d 2 PIN ASTM A29 Gr G4130 CE-891270 CE-889784 G09-H60-ZV-1032
CE-891271 CE-889785 G09-H60-ZV-1052
77e 2 PIN ASTM A29 Gr G4130
CE-891273 CE-889787 G09-H60-ZV-1148
86 4 LIFTING LUG ASTM A973 Gr.100 REV.NO.

D
DATE

06/06/2017
REVISION DESCRIPTION

ISSUED FOR APPROVAL

99 1 ADAPTER PLATE ASTM A516-Gr70 S5 This document contains Perar Spa proprietary
and confidential informations. It is loaned for
limited purposes only. It may not be
Tollerances, unless
otherwise stated
Greater of To ±
TM

99a 1 ADAPTER FLANGE ASTM A516-Gr70 S5

reproduced in whole or part or disclosed to third
parties without the prior written consent of 0 75 0.1 TITLE
Perar Spa. The document is to be returned to
SIDE ENTRY BALL VALVE
Perar Spa upon request and in all events upon
75 200 0.3

NOTES: completion of the use for which it was loaned. 200 500 0.5
500 Over 1.5 SUBJECT
A3
Scale Size
GENERAL ASSEMBLY DRAWING Angle ± ½°
General Outline Drawings
(1) INCONEL 625 OVERLAY ON ALL WETTED AREA (MIN. THK 3 mm) AS PER 02-SAMSS-012 TYPE OF TEST TEST PRESSURE (PSIG)
LEAKAGE RATE 2/4 Sheet
Surface finish to be 3 Ra
Remove all burrs and sharp edges SIZE CLASS Weight D
ACCEPTANCE CRITERIA 1 13/16"
REVISIONS API 10000 On-Off Valves With Actuators, 10000 PSI
(2) TUNGSTEN CARBIDE COATING (MIN THK 0.2 mm) Hydrostatic Body 15,000 PSL 3 Mod. Description Date Dwg. Ver. Appr. Digital
Signature
Drawing by
Doriano Firma digitale di
Doriano Saligari
Verified by
Fulvio
Firma digitale di
Fulvio Tamola
Approved by
Alessandro
Firma digitale di
Alessandro
Barberini
Hasbah-II Wellheads Facilities
Hydrostatic Seat 10,000 PSL 3 1 Revision according to Customers Comment's 17/03/17 Raschetti Tamola Barberini Saligari Data: 2017.06.06
16:19:56 +0200 Tamola
Data:
2017.06.06
16:20:04 +0200
Barberini Data: 2017.06.06
16:20:14 +0200

Date Drawing by Verified by Approved by

Gas Body Test 10,000 PSL 4 2 Revision according to Customers Comment's 09/05/17 Raschetti Tamola Barberini HASBAH SAUDI ARABIA
Primary Gas Seat Test 10,000 PSL 4 3 Revision according to Customers Comment's 06/06/17 Raschetti Tamola Barberini
23/01/17 Saligari Tamola Barberini
DWG N°
Secondary Gas Seat Test 500 to 1000 PSL 4
Low pressure gas seat 80 to 100 PSL 4 CD-16-0351-X-00CS REV3 G09 L PERACT-PI-Q23-DW-0004 2 D
VALVE DATASHEET NUMBER ISS DOCUMENT NUMBER VALVE TAG PIPING SPEC
CE-881844 CE-880388 G09-H40-MOV-1085
CE-881843 CE-880387 G09-H40-MOV-1090
CE-881172 CE-881094 G09-H40-MOV-1105
CE-881171 CE-881093 G09-H40-MOV-1110 3
CE-881845 CE-880389 G09-H40-MOV-1125
CE-881850 CE-880394 G09-H40-MOV-1130
CE-881859 CE-880403 G09-H40-MOV-1145
CE-881857 CE-880401 G09-H40-MOV-1163
CE-832897 CE-831412 G09-H44-MOV-1110
CE-832898 CE-831413 G09-H44-MOV-1090
CE-832899 CE-831414 G09-H44-MOV-1085
CE-832900 CE-831415 G09-H44-MOV-1105
CE-832901 CE-831416 G09-H44-MOV-1125
CE-832906 CE-831421 G09-H44-MOV-1130
CE-832915 CE-831430 G09-H44-MOV-1145
CE-832913 CE-831428 G09-H44-MOV-1163
CE-884227 CE-882742 G09-H48-MOV-1085
CE-884226 CE-882741 G09-H48-MOV-1090
CE-884228 CE-882743 G09-H48-MOV-1105
CE-884225 CE-882740 G09-H48-MOV-1110
CE-884229 CE-882744 G09-H48-MOV-1125
601.1
3
CE-884234 CE-882749 G09-H48-MOV-1130
CE-884243 CE-882758 G09-H48-MOV-1145 D
C
06/06/2017
05/09/2017
ISSUED FOR APPROVAL
ISSUED FOR APPROVAL
M.R.
M.R.
F.T.
F.T.
A.B.
A.B.
95LL0T02 B 03/17/2017 ISSUED FOR APPROVAL M.R. F.T. A.B.
CE-884241 CE-882756 G09-H48-MOV-1163 A 01/23/2017 ISSUED FOR APPROVAL D.S. F.T. A.B.
CE-886532 CE-885076 G09-H52-MOV-1085 DESCRIPTION

CE-886531 CE-885075 G09-H52-MOV-1090

CE-886533 CE-885077 G09-H52-MOV-1125
CE-886538 CE-885082 G09-H52-MOV-1130 16-351 CD-16-0351-X-00CS D
CE-886547 CE-885091 G09-H52-MOV-1145
CE-886545 CE-885089 G09-H52-MOV-1163
CE-888904 CE-887419 G09-H56-MOV-1110 16-351
FGCI-M98-89-A039-DA A 01/23/2017
CE-888905 CE-887420 G09-H56-MOV-1090 B 03/17/2017
PI-Q23-MR-4045 C 05/09/2017
CE-888906 CE-887421 G09-H56-MOV-1085 D 06/06/2017
NTS
CE-888907 CE-887422 G09-H56-MOV-1105
CE-888908 CE-887423 G09-H56-MOV-1125
CE-888913 CE-887428 G09-H56-MOV-1130
CE-888922 CE-887437 G09-H56-MOV-1145
CE-888920 CE-887435 G09-H56-MOV-1163
REV.NO. DATE REVISION DESCRIPTION
CE-891242 CE-889756 G09-H60-MOV-1110 D 06/06/2017 ISSUED FOR APPROVAL
This document contains Perar Spa proprietary Tollerances, unless TM
CE-891243 CE-889757 G09-H60-MOV-1090 and confidential informations. It is loaned for
limited purposes only. It may not be
reproduced in whole or part or disclosed to third
otherwise stated
Greater of To ±
parties without the prior written consent of 0 75 0.1 TITLE

CE-891244 CE-889758 G09-H60-MOV-1085 Perar Spa. The document is to be returned to

Perar Spa upon request and in all events upon
completion of the use for which it was loaned.
75
200
200
500
0.3
0.5 SIDE ENTRY BALL VALVE
500 Over 1.5 SUBJECT

CE-891245 CE-889759 G09-H60-MOV-1105 Scale Size A3 Angle ± ½°

GENERAL ASSEMBLY DRAWING General Outline Drawings
Sheet 3/4
Surface finish to be 3 Ra
Remove all burrs and sharp edges SIZE CLASS Weight D
CE-891246 CE-889760 G09-H60-MOV-1125 REVISIONS 1 13/16" API 10000 On-Off Valves With Actuators, 10000 PSI
Drawing by Verified by Approved by
Mod. Description Date Dwg. Ver. Appr. Digital
Hasbah-II Wellheads Facilities
Firma digitale di

CE-891251 CE-889765 G09-H60-MOV-1130

Firma digitale di Firma digitale di Alessandro
Signature Doriano Doriano Saligari
Data:
Fulvio Fulvio Tamola
Data:
Alessandro Barberini

Saligari Barberini Data:

1 Revision according to Customers Comment's 17/03/17 Raschetti Tamola Barberini 2017.06.06
16:20:26 +0200 Tamola 2017.06.06
16:20:34 +0200
2017.06.06
16:20:43 +0200

Date Drawing by Verified by Approved by

2 Revision according to Customers Comment's 09/05/17 Raschetti Tamola Barberini HASBAH SAUDI ARABIA
CE-891260 CE-889774 G09-H60-MOV-1145 3 Revision according to Customers Comment's 06/06/17 Raschetti Tamola Barberini
23/01/17 Saligari Tamola Barberini
DWG N°

CE-891258 CE-889772 G09-H60-MOV-1163 CD-16-0351-X-00CS REV3 G09 L PERACT-PI-Q23-DW-0004 3 D

GAINT BUTTON HEAD INJECTION FITTING, 15 000 PSI, SECTIONAL VIEW
6.5

-0.1
1/4 " NPT

-0.1
0
CH. 24

CH. 32
0

O 16
M27
O 17.5
O 22
3.5 +0.1
0

N°2 HOLES O 3
601.1
3

D 06/06/2017 ISSUED FOR APPROVAL M.R. F.T. A.B.

C 05/09/2017 ISSUED FOR APPROVAL M.R. F.T. A.B.
ADAPTER PLATE B 03/17/2017 ISSUED FOR APPROVAL M.R. F.T. A.B.
A 01/23/2017 ISSUED FOR APPROVAL D.S. F.T. A.B.
DESCRIPTION

16-351 CD-16-0351-X-00CS D
GLAND
16-351
FGCI-M98-89-A039-DA A 01/23/2017
43a B 03/17/2017
PI-Q23-MR-4045 C 05/09/2017
D 06/06/2017
NTS

CAP

REV.NO. DATE REVISION DESCRIPTION

D 06/06/2017 ISSUED FOR APPROVAL

This document contains Perar Spa proprietary Tollerances, unless TM
and confidential informations. It is loaned for otherwise stated
limited purposes only. It may not be
GREASE FITTING reproduced in whole or part or disclosed to third
parties without the prior written consent of
Perar Spa. The document is to be returned to
Greater of
0
To
75
±
0.1 TITLE
Perar Spa upon request and in all events upon
completion of the use for which it was loaned.
75
200
200
500
0.3
0.5 SIDE ENTRY BALL VALVE
500 Over 1.5 SUBJECT
A3
Scale Size Angle ± ½°
GENERAL ASSEMBLY DRAWING General Outline Drawings
BODY Sheet 4/4
Surface finish to be 3 Ra
Remove all burrs and sharp edges SIZE CLASS Weight D
REVISIONS 1 13/16" API 10000 On-Off Valves With Actuators, 10000 PSI
Drawing by Verified by Approved by
Mod. Description Date Dwg. Ver. Appr. Digital
Hasbah-II Wellheads Facilities
Firma digitale di Firma digitale di
Signature Doriano Firma digitale di
Doriano Saligari Fulvio Fulvio Tamola
Data: Alessandro Alessandro
Barberini
Saligari Tamola 2017.06.06 Barberini
Revision according to Customers Comment's 17/03/17 Raschetti Tamola Barberini
Data: 2017.06.06
1 16:20:53 +0200 16:21:01 +0200 Data: 2017.06.06
16:21:08 +0200

Date Drawing by Verified by Approved by

2 Revision according to Customers Comment's 09/05/17 Raschetti Tamola Barberini HASBAH SAUDI ARABIA

3 Revision according to Customers Comment's 06/06/17 Raschetti Tamola Barberini

23/01/17 Saligari Tamola Barberini
DWG N°

CD-16-0351-X-00CS REV3 G09 L PERACT-PI-Q23-DW-0004 4 D