Scribd
Upload
189 views4 pages

15 BC547

A transistor is a semiconductor device with three connections - the emitter, base, and collector. A small current flowing between the base and emitter controls a larger current flowing between the collector and emitter. Transistors exist in two configurations - PNP or NPN. The collector characteristics curves show the relationship between collector current and collector voltage for different base currents. The current gain, hFE, is the ratio of collector to base current and typically ranges from 10 to 500. A small alternating current signal at the base is amplified at the collector.

Uploaded by

Niranjan Reddy
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
189 views4 pages

15 BC547

A transistor is a semiconductor device with three connections - the emitter, base, and collector. A small current flowing between the base and emitter controls a larger current flowing between the collector and emitter. Transistors exist in two configurations - PNP or NPN. The collector characteristics curves show the relationship between collector current and collector voltage for different base currents. The current gain, hFE, is the ratio of collector to base current and typically ranges from 10 to 500. A small alternating current signal at the base is amplified at the collector.

Uploaded by

Niranjan Reddy
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 4

TRANSISTOR

INTRODUCTION

A transistor is a solid-state, semiconductor device with three electrical connections (emitter,


base, collector). A small current flowing between base and emitter has the ability to control a much
larger current flowing between the collector and emitter. Transistors can be manufactured in two
distinct configurations: PNP or NPN. The N's and P's refer to the kind of impurity introduced into
the crystal structure of the various regions of the transistor. This determines which way the currents
flow through the transistor. The circuit symbol for a transistor reveals its configuration by the
direction of an arrow placed on the emitter lead and distinguishes the emitter from the collector as
shown in Figure 1.

P N P Transistor
N P N Transistor

Figure 1. Construction and circuit symbol for PNP and NPN transistors.

If, in the case of an NPN transistor, a positive voltage is applied to the collector (and the emitter
connected to the negative terminal to complete the circuit) no current will flow unless a small
current is allowed to flow through the base to the emitter. (For older types of transistor a small
leakage current, uncontrolled by the IB, but dependent on the temperature, flows between the emitter
and collector). The amount of collector current depends almost entirely on the amount of base
current and the first part of the experiment is concerned with determining the extent of this
dependence by plotting a set of curves known as the collector characteristics. The collector
characteristics are a family of curves showing the collector current flowing as a function of collector
voltage for various values of base current as shown in Figure 2. From the collector characteristics
the current amplification of the transistor may be determined.
Figure 2. Characteristic curves for a transistor

At any point X (in Figure 2) we may define a current ratio


Ic (X)
h FE =
IB (X)
(1)
which typically may be from 10 to 500 depending on the transistor. Few are less than 10 (unless
they are faulty) and a value in excess of 500 would indicate a rather exceptional transistor. In some
references αFE or ß may be used instead of hFE.

The symbol h refers to what are known as "hybrid parameters", of which there are four to describe
most of the circuit properties of a transistor at low frequencies. The F identifies the h-parameter as
the Forward Current Amplification Factor and the E refers to circuit operation with the Emitter
common to both the input and output circuits surrounding the transistor, as shown in Figure 3.

Figure 3. Identification of Input and Output circuits for an NPN transistor

A small current IB in the input circuit will control a larger current and

IC = hFE IB (2)
In most applications, such as amplifiers or radios, an alternating (AC) signal current is amplified.
An alternating current flows in both forward and reverse directions but transistor action occurs only
for current flowing in one direction through the transistor. This is achieved by adding a D.C. bias to
the signal. The forward half-cycles of the A.C. signal add to the bias current and the reverse half-
cycles subtract from it. To measure the amplification produced by the transistor for A.C. signals we
use
Δ IC (X)
h fe =
Δ IB (X)
(3)
at a constant VCE as shown in Figure 4.

Figure 4. Measurement parameters for hfe (see equation 3)

You might also like