HST-3

EXPANSION ANCHOR
Technical Datasheet
Update: Apr-18
HST3 Expansion anchor
Ultimate-performance expansion anchor for cracked concrete and seismic
Anchor version Benefits
- Highest resistance for reduced member
thickness, short spacing and edge
distances
HST3
HST3-R - Increased undercut percentage in
(M8-M24) combination with optimized coating
- Suitable for non-cracked and cracked
concrete C 12/15 to C 80/95
- Highly reliable and safe anchor for
structural seismic design with ETA
C1/C2 approval
- Flexibility with two embedment depths
included in the ETA
- Minimum edge and spacing distances
HST3-BW reduced by up to 25% compared to HST
HST3-R-BW
- Design tension resistance increased by
(M8-M24)
up to 66% compared to HST
- Product and length identification mark
facilitates quality control and inspection

Base material Load conditions

Concrete Concrete Static/ Seismic Fire

(non-cracked) (cracked) quasi-static ETA-C1/C2 resistance

Installation conditions Other information

Hammer Diamond Hollow drill- Impact wrench European CE PROFIS FM

drilled holes drilled holes bit drilling with adaptative Technical conformity Anchor design approved
torque module Assessment Software

Approvals / certificates
Description Authority / Laboratory No. / date of issue
European technical assessment a) DIBt, Berlin ETA-98/0001 / 2018-02-09
Fire test report DIBt, Berlin ETA-98/0001 / 2018-02-09
Shock approval FOCP, Zurich BZS D 08-602 / 2016-08-17
a) All data given in this section according to ETA-98/0001, issue 2017-20-07.

1 Updated: Apr-18
Static and quasi-static loading (for a single anchor)

All data in this section applies to:

- Correct setting (See setting instruction)
- No edge distance and spacing influence
- Steel failure
- Minimum base material thickness
- Concrete C 20/25, fck,cube = 25 N/mm²

Effective anchorage depth for static

Anchor size M8 M10 M12 M16 M20 M24
Eff. Anchorage depth hef [mm] 47 40 60 50 70 65 85 101 125

Mean ultimate resistance

Anchor size M8 M10 M12 M16 M20 M24
Non-cracked concrete
Tension HST3/HST3-BW 15,9 17,0 29,2 23,7 33,2 35,1 52,5 68,1 79,7
[kN]
NRu,m HST3-R/HST3-R-BW 15,9 17,0 29,2 23,7 33,2 35,1 52,5 68,1 79,7
Shear HST3/HST3-BW 14,5 23,0 24,8 35,7 37,2 57,2 58,1 88,1 98,7
[kN]
VRu,m HST3-R/HST3-R-BW 16,5 26,9 26,6 32,7 38,5 51,0 66,8 102,1 120,8
Cracked concrete
Tension HST3/HST3-BW 10,6 12,1 19,9 16,9 26,6 25,0 37,5 48,5 53,1
[kN]
NRu,m HST3-R/HST3-R-BW 11,3 12,1 19,9 16,9 26,6 25,0 37,5 48,5 53,1
Shear HST3/HST3-BW 14,5 23,0 24,8 35,7 37,2 57,2 58,1 88,1 98,7
[kN]
VRu,m HST3-R/HST3-R-BW 16,5 26,9 26,6 32,7 38,5 51,0 66,8 102,1 120,8

Characteristic resistance
Anchor size M8 M10 M12 M16 M20 M24
Non-cracked concrete
Tension HST3/HST3-BW 12,0 12,8 22,0 17,9 25,0 26,5 39,6 51,3 60,0
[kN]
NRk HST3-R/HST3-R-BW 12,0 12,8 22,0 17,9 25,0 26,5 39,6 51,3 60,0
Shear HST3/HST3-BW 13,8 21,9 23,6 34,0 35,4 54,5 55,3 83,9 94,0
[kN]
VRk HST3-R/HST3-R-BW 15,7 25,6 25,3 31,1 36,7 48,6 63,6 97,2 115,0
Cracked concrete
Tension HST3/HST3-BW 8,0 9,1 15,0 12,7 20,0 18,9 28,2 36,5 40,0
[kN]
NRk HST3-R/HST3-R-BW 8,5 9,1 15,0 12,7 20,0 18,9 28,2 36,5 40,0
Shear HST3/HST3-BW 13,8 21,9 23,6 34,0 35,4 54,5 55,3 83,9 94,0
[kN]
VRk HST3-R/HST3-R-BW 15,7 24,3 25,3 31,1 36,7 48,6 63,6 97,2 115,0

Updated: Apr-18 2
Design resistance
Anchor size M8 M10 M12 M16 M20 M24
Non-cracked concrete
Tension HST3/HST3-BW 8,0 8,5 14,7 11,9 16,7 17,6 26,4 34,2 40,0
[kN]
NRd HST3-R/HST3-R-BW 8,0 8,5 14,7 11,9 16,7 17,6 26,4 34,2 40,0
Shear HST3/HST3-BW 11,0 17,5 18,9 27,2 28,3 43,6 44,2 67,1 62,7
[kN]
VRd HST3-R/HST3-R-BW 12,6 20,5 20,2 24,9 29,4 38,9 50,9 77,8 88,5
Cracked concrete
Tension HST3/HST3-BW 5,3 6,1 10,0 8,5 13,3 12,6 18,8 24,4 26,7
[kN]
NRd HST3-R/HST3-R-BW 5,7 6,1 10,0 8,5 13,3 12,6 18,8 24,4 26,7
Shear HST3/HST3-BW 11,0 16,2 18,9 23,6 28,3 42,9 44,2 67,1 62,7
[kN]
VRd HST3-R/HST3-R-BW 12,6 16,2 20,2 23,6 29,4 38,9 50,9 77,8 83,9

Recommended loadsa)
Anchor size M8 M10 M12 M16 M20 M24
Non-cracked concrete
Tension HST3/HST3-BW 5,7 6,1 10,5 8,5 11,9 12,6 18,8 24,4 28,6
[kN]
NRec HST3-R/HST3-R-BW 5,7 6,1 10,5 8,5 11,9 12,6 18,8 24,4 28,6
Shear HST3/HST3-BW 7,9 12,5 13,5 19,4 20,2 31,1 31,6 47,9 44,8
[kN]
VRec HST3-R/HST3-R-BW 9,0 14,6 14,5 17,8 21,0 27,8 36,3 55,5 63,2
Cracked concrete
Tension HST3/HST3-BW 3,8 4,3 7,1 6,1 9,5 9,0 13,4 17,4 19,0
[kN]
NRec HST3-R/HST3-R-BW 4,0 4,3 7,1 6,1 9,5 9,0 13,4 17,4 19,0
Shear HST3/HST3-BW 7,9 11,6 13,5 16,8 20,2 30,6 31,6 47,9 44,8
[kN]
VRec HST3-R/HST3-R-BW 9,0 11,6 14,5 16,8 21,0 27,8 36,3 55,5 59,9
a) With overall partial safety factor for action  = 1,4, The partial safety factors for action depend on the type of loading and shall be
taken from national regulations,

Seismic loading (for a single anchor)

All data in this section applies to:

- Correct setting (See setting instruction)
- No edge distance and spacing influence
- Steel failure
- Minimum base material thickness
- Concrete C 20/25, fck,cube = 25 N/mm²
- αgap = 1,0 (using Hilti seismic filling set)

Effective anchorage depth for seismic C2 and C1

Anchor size M8 M10 M12 M16 M20 M24
Eff, Anchorage depth hef [mm] 47 60 70 85 101 -

Characteristic resistance in case of seismic performance C2

Anchor size M8 M10 M12 M16 M20 M24
Tension HST3 / HST3-BW 3,0 10,4 17,9 24,0 31,1 -
[kN]
NRk, seis HST3-R / HST3-R-BW 3,4 10,4 17,9 24,0 31,1 -
Shear HST3 / HST3-BW 9,9 19,0 28,6 48,5 84,3 -
[kN]
VRk,seis HST3-R / HST3-R-BW 9,9 17,2 27,6 42,5 67,4 -

3 Updated: Apr-18
 Design resistance in case of seismic performance C2
Anchor size M8 M10 M12 M16 M20 M24
Tension HST3 / HST3-BW 2,0 6,9 11,9 16,0 20,7 -
[kN]
NRd, seis HST3-R / HST3-R-BW 2,3 6,9 11,9 16,0 20,7 -
Shear HST3 / HST3-BW 7,9 15,2 22,9 38,8 66,3 -
[kN]
VRd,seis HST3-R / HST3-R-BW 7,9 13,8 22,1 34,0 53,9 -

Characteristic resistance in case of seismic performance C1

Anchor size M8 M10 M12 M16 M20 M24
Tension HST3 / HST3-BW 7,5 12,0 17,9 24,0 31,1 -
[kN]
NRk, seis HST3-R / HST3-R-BW 7,5 12,0 17,9 24,0 31,1 -
Shear HST3 / HST3-BW 16,6 25,8 39,0 60,9 99,4 -
[kN]
VRk,seis HST3-R / HST3-R-BW 19,5 28,4 44,3 70,2 99,4 -

Design resistance in case of seismic performance C1

Anchor size M8 M10 M12 M16 M20 M24
Tension HST3 / HST3-BW 5,0 8,0 11,9 16,0 20,7 -
[kN]
NRd, seis HST3-R / HST3-R-BW 5,0 8,0 11,9 16,0 20,7 -
Shear HST3 / HST3-BW 13,3 20,6 31,2 48,7 66,3 -
[kN]
VRd,seis HST3-R / HST3-R-BW 15,6 22,7 33,2 54,5 66,3 -

Fire resistance

All data in this section applies to:

- Correct setting (See setting instruction)
- No edge distance and spacing influence
- Steel failure
- Minimum base material thickness
- Concrete C 20/25, fck,cube = 25 N/mm²
- Hilti technical data for concrete strength class C55/67 to C80/95: for a structural element that fullfills the
requirements according to DIN EN 1992-1-2 the fire resistance of C20/25 could be assumed.
- partial safety factor for resistance under fire exposure M,fi=1,0 (in absence of other national regulations)

Effective anchorage depth for static

Anchor size M8 M10 M12 M16 M20 M24
Eff. Anchorage depth hef [mm] 47 40 60 50 70 65 85 101 125

Characteristic resistance
Anchor size M8 M10 M12 M16 M20 M24
Fire Exposure R30
Tension HST3/HST3-BW 0,9 1,5 2,4 2,3 5,0 4,4 7,1 9,1 12,6
[kN]
NRk,fi HST3-R/HST3-R-BW 1,9 1,8 3,0 3,2 5,0 4,7 7,1 9,1 12,6
Shear HST3/HST3-BW 0,9 1,5 2,4 2,3 5,2 4,4 9,7 15,2 21,9
[kN]
VRk,fi HST3-R/HST3-R-BW 4,9 4,7 11,8 8,9 17,1 16,9 31,9 37,0 62,8
Fire Exposure R120
Tension HST3/HST3-BW 0,6 0,8 0,9 0,8 1,3 1,5 2,4 3,8 5,4
[kN]
NRk,fi HST3-R/HST3-R-BW 1,5 1,5 2,4 2,5 4,0 3,8 5,6 7,3 10,1
Shear HST3/HST3-BW 0,6 0,8 0,9 0,8 1,5 1,5 2,4 3,8 5,4
[kN]
VRk,fi HST3-R/HST3-R-BW 1,7 2,0 3,3 3,3 4,8 6,2 9,0 14,1 20,3

Updated: Apr-18 4
Design resistance
Anchor size M8 M10 M12 M16 M20 M24
Fire Exposure R30
Tension HST3/HST3-BW 0,9 1,5 2,4 2,3 5,0 4,4 7,1 9,1 12,6
[kN]
NRd,fi HST3-R/HST3-R-BW 1,9 1,8 3,0 3,2 5,0 4,7 7,1 9,1 12,6
Shear HST3/HST3-BW 0,9 1,5 2,4 2,3 5,2 4,4 9,7 15,2 21,9
[kN]
VRd,fi HST3-R/HST3-R-BW 4,9 4,7 11,8 8,9 17,1 16,9 31,9 37,0 62,8
Fire Exposure R120
Tension HST3/HST3-BW 0,6 0,8 0,9 0,8 1,3 1,5 2,4 3,8 5,4
[kN]
NRd,fi HST3-R/HST3-R-BW 1,5 1,5 2,4 2,5 4,0 3,8 5,6 7,3 10,1
Shear HST3/HST3-BW 0,6 0,8 0,9 0,8 1,5 1,5 2,4 3,8 5,4
[kN]
VRd,fi HST3-R/HST3-R-BW 1,7 2,0 3,3 3,3 4,8 6,2 9,0 14,1 20,3

Materials

Mechanical properties
Anchor size M8 M10 M12 M16 M20 M24
Nominal tensile HST3/HST3-BW 800 800 800 720 700 530
[N/mm²]
strength fuk,thread HST3-R/HST3-R-BW 720 710 710 650 650 650
Yield strength HST3/HST3-BW 640 640 640 576 560 450
fyk,thread HST3-R/HST3-R-BW [N/mm²] 576 568 568 520 520 500
Stressed cross-section As [mm²] 36,6 58,0 84,3 157 245 353
Moment of resistance W [mm³] 31,2 62,3 109 277 541 935
Char, bending HST3/HST3-BW 30 60 105 240 457 595
[Nm]
resistance M0Rk,s HST3-R/HST3-R-BW 27 53 93 216 425 730

Material quality
Part Material
M10, M16: Galvanized or Stainless steel
Expansion HST3/HST3-BW
M8, M12, M20, M24: Stainless steel
sleeve
HST3-R/HST3-R-BW Stainless steel A4
HST3/HST3-BW Carbon steel, galvanized, coated (transparent)
Bolt
HST3-R/HST3-R-BW Stainless steel A4, cone coated (transparent)
HST3/HST3-BW Galvanized
Washer
HST3-R/HST3-R-BW Stainless steel A4
HST3/HST3-BW Strength class 8
Hexagon nut
HST3-R/HST3-R-BW Stainless steel A4, coated

Anchor dimensions of HST3, HST3-BW, HST3-R, HST3-R-BW

Anchor size M8 M10 M12 M16 M20 M24
Maximum length of anchor lmax ≤ [mm] 260 280 350 475 450 500
Shaft diameter at the cone dR [mm] 5,60 6,94 8,22 11,00 14,62 17,4
Length of expansion sleeve ls [mm] 13,6 16,0 20,0 25,0 28,3 36,0
Diameter of washer dw ≥ [mm] 15,57 19,48 23,48 29,48 36,38 43,38

5 Updated: Apr-18
Setting information

Setting details
Anchor size M8 M10 M12 M16 M20 M24
Nominal diameter of drill bit do [mm] 8 10 12 16 20 24
Cutting diameter of drill bit dcut ≤ [mm] 8,45 10,45 12,5 16,5 20,55 24,55
hef,1 [mm] - 40 50 65 - -
Effective embedment depth
hef,2 [mm] 47 60 70 85 101 125
h1,1 ≥ [mm] - 53 68 86 - -
Drill hole depth1)
h1,2 ≥ 59 73 88 106 124 151
hnom,1 [mm] - 48 60 78 - -
Thread engagement length
hnom,2 [mm] 54 68 80 98 116 143
Maximum diameter of clearance
df [mm] 9 12 14 18 22 26
hole in the fixture
Torque moment Tinst [Nm] 20 45 60 110 180 300
Maximum thickness of fixture tfix,max [mm] 195 220 270 370 310 330
Width across ≤
SW [mm] 13 17 19 24 30 36
1) In case of diamond drilling +5 mm for M8 to M10 and +2 mm for M12 to M24.

Installation equipment
Anchor size M8 M10 M12 M16 M20 M24
Rotary hammer TE2(-A) – TE30(-A) TE40 – TE80
Diamond coring tool DD-30W, DD-EC1
Setting tool Hilti S7W 6AT 22A – SI-AT-A22 -
Hollow drill bit - TE-CD, TE-YD
Other tools hammer, torque wrench, blow out pump

Updated: Apr-18 6
Setting parameters of HST3 / HST3-R for M8 and M10
M10
Anchor Size M8
C20/25 to C50/60a) C12/15b) C12/15 to C20/25 to C50/60a) C12/15b)
Concrete class C55/67 to C80/95b) C16/20b) C16/20a) C55/67 to C80/95b) C16/20b)
Effective anchorage
hef [mm] 47 47 40 60 60
depth
Minimum base material
hmin [mm] 80 100 100 80 100 120 120
thickness
Minimum spacing in smin [mm] 35 35 35 50 40 40 70
non-cracked concrete for c ≥ [mm] 55 50 65 95 100 60 90
Minimum spacing in smin [mm] 35 35 35 40 40 40 45
cracked concrete for c ≥ [mm] 50 50 55 90 100 55 85
Minimum edge distance cmin [mm] 40 40 50 50 60 50 80
in non-cracked concrete for s ≥ [mm] 50 50 80 190 90 90 120
Minimum edge distance cmin [mm] 40 40 40 45 60 45 70
in cracked concrete for s ≥ [mm] 50 50 75 180 90 80 120
Critical spacing for scr,sp [mm] 141 188 168 180 240
splitting failure and
concrete cone failure scr,N [mm] 141 141 120 180 180
Critical edge distance for ccr,sp [mm] 71 94 84 90 120
splitting failure and
concrete cone failure ccr,N [mm] 71 71 60 90 90

Setting parameters of HST3 / HST3-R for M12 and M16

Anchor Size M12 M16
10
C20/25 to C20/25 to C50/60a) C12/15b) C20/25 to C20/25 to C50/60a) C12/15b)
Concrete class C50/60a) C55/67 to C80/95b) C16/20b) C50/20a) C55/67 to C80/95b) C16/20b)
Effective anchorage hef [mm] 50 70 70 65 85 85
depth
Minimum base material hmin [mm] 100 120 140 140 120 140 160 160
thickness
Minimum spacing in smin [mm] 55 50 60 110 75 80 65 90
non-cracked concrete for c [mm] 110 100 70 140 140 130 95 145
Minimum spacing in ≥smin [mm] 50 50 50 80 65 80 65 70
cracked concrete for c ≥ [mm] 105 90 70 120 130 130 95 125
Minimum edge distance cmin [mm] 60 60 55 90 65 65 65 110
in non-cracked concrete for s ≥ [mm] 210 120 110 190 240 180 150 170
Minimum edge distance cmin [mm] 55 60 55 80 65 65 65 90
in cracked concrete for s ≥ [mm] 210 120 110 170 240 180 150 165
Critical spacing for scr,sp [mm] 180 210 280 208 255 340
splitting failure and
concrete cone failure scr,N [mm] 150 210 210 195 255 255
Critical edge distance for ccr,sp [mm] 90 105 140 104 128 170
splitting failure and
concrete cone failure ccr,N [mm] 75 105 105 98 128 128

7 Updated: Apr-18
Setting parameters of HST3(-BW) / HST3-R(-BW) for M20 and M24
Anchor Size M20 M24
C20/25 to C50/60a) C12/15b) C20/25 to C50/60a) C12/15b)
Concrete class C55/67 to C80/95b) C16/20b) C55/67 to C80/95b) C16/20b)
Effective anchorage hef [mm] 101 101 125 125
depth
Minimum base material hmin [mm] 160 200 200 250 250
thickness
Minimum HST3 smin [mm] 120 90 90 125 180
spacing in HST3-BW for c ≥ [mm] 180 130 165 255 375
non-cracked HST3-R smin [mm] 120 90 90 125 180
concrete HST3-R-BW for c ≥ [mm] 180 130 165 205 375
Minimum HST3 smin [mm] 120 90 90 125 140
spacing in for c ≥
HST3-BW [mm] 180 130 165 180 325
cracked HST3- smin [mm] 120 90 90 125 140
concrete RHST3-R-BW for c ≥ [mm] 180 130 140 130 325
Min. edge HST3 cmin [mm] 120 80 90 170 260
distance in HST3-BW for s ≥ [mm] 180 180 140 295 400
non-cracked HST3-R cmin [mm] 120 80 120 150 260
concrete HST3-R-BW for s ≥ [mm] 180 180 270 235 400
Min. edge HST3 cmin [mm] 120 80 100 125 230
distance in HST3-BW for s ≥ [mm] 180 180 240 240 295
cracked HST3-R cmin [mm] 120 80 100 125 230
concrete HST3-R-BW for s ≥ [mm] 180 180 240 140 295
Critical spacing for scr,sp [mm] 384 404 375 500
splitting failure and concrete
cone failure scr,N [mm] 303 303 375 375
Critical spacing for ccr,sp [mm] 192 202 188 250
splitting failure and
concrete cone failure ccr,N [mm] 152 152 188 188
a) Data covered by ETA-98/0001 issue 2017-20-07.
b) Data covered by Hilti Technical Data
For spacing (edge distance) smaller than critical spacing (critical edge distance) the design loads have to
be reduced.

Updated: Apr-18 8
Setting instructions

*For detailed information on installation see instruction for use given with the package of the product
Setting instruction for HST3, HST3-BW, HST3-R, HST3-R-BW
Hammer drilling (M8, M10, M12, M16, M20, M24)
1. Drill the hole 2. Clean the hole

3a. Insert the anchor with hammer 3a. Insert the anchor with setting tool HS-SC

4. Check 5a. Torque with calibrated torque wrench (M8-M24)

5b. Torque with impact wrench with Adaptative torque module (M8-M12)

Hollow Drill Bit (M16, M20, M24), no cleaning required

1. Drill the hole with the Hollow drill bit 2a. Insert the anchor with hammer

2b. Insert the anchor with setting tool HS-SC 3. Check

9 Updated: Apr-18
 5a. Torque with calibrated torque wrench (M8-M24) 5b. Torque with impact wrench with Adaptative
torque module (M8-M12)

Diamond coring (M8, M10, M12, M16, M20, M24)

1. Core the hole 2. Flushing

3. Clean the hole 4a. Insert the anchor with hammer

4b. Use a setting tool HS-SC 5. Check

6a. Torque with calibrated torque wrench (M8-M24) 5b. Torque with impact wrench with Adaptative
torque module (M8-M12)

Updated: Apr-18 10